Commit Graph

28641 Commits

Author SHA1 Message Date
Nick Hainke
7c5e847827 kernel: move CONFIG_PAGE_POOL to generic
Move "# CONFIG_PAGE_POOL is not set" to generic.

Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-03-04 10:20:58 +01:00
Álvaro Fernández Rojas
12a3c863d2 bmips: loader-lzma: drop unused RAMSIZE parameter
This parameter has never been used.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-03-02 20:37:56 +01:00
Álvaro Fernández Rojas
05603df730 bcm63xx: loader-lzma: drop unused RAMSIZE parameter
This parameter has never been used.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-03-02 20:37:56 +01:00
Felix Fietkau
9307c27539 kernel: fix mtk dsa tag padding
The padding intended to avoid corrupted non-zero padding payload was
accidentally adding too many padding bytes, tripping up some setups.
Fix this by using eth_skb_pad instead.
Fixes #11942.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-03-02 12:59:53 +01:00
Felix Fietkau
23b46b1c61 linux-firmware: add mt7986 offload firmware
This is needed for WED support on MT7986.
Enable it by default for the filogic subtarget.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-03-02 11:25:17 +01:00
Bjørn Mork
79bd0172ca mt7621: move uboot-envtools to DEFAULT_PACKAGES
Several devices depend on fw_printenv during sysupgrade.  Make sure
it always is present in all images, including initramfs images built
by the buildbots.

Fixes: 2449a63208 ("ramips: mt7621: Add support for ZyXEL NR7101")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-03-01 23:24:23 +01:00
Sergio Paracuellos
84c04ff406 ramips: rt5350: enable lzma-loader for ALLNET ALL5003
Fixes the boot loader LZMA decompression issue:
LZMA ERROR 1 - must RESET board to recover

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
2023-03-01 22:15:13 +01:00
John Audia
736257141f kernel: bump 5.15 to 5.15.96
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-28 04:38:13 -05:00
John Audia
de8d5b50e2 kernel: bump 5.15 to 5.15.95
Removed upstreamed:
	backport-5.15/807-v6.1-0003-nvmem-core-add-error-handling-for-dev_set_name.patch[1]
	bcm47xx/patches-5.15/070-net-bgmac-fix-BCM5358-support-by-setting-correct-fla.patch[2]

Added fix:
	backport-5.15/883-0001-net-Remove-WARN_ON_ONCE-sk-sk_forward_alloc-from-sk_.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.95&id=14eea6449473c1f55e196cc104ba16d144465869
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.95&id=2603a5ca6223bb3a88814e2728335eec14f715ab
3. https://lore.kernel.org/stable/20230227211548.13923-1-kuniyu@amazon.com

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-28 04:38:13 -05:00
Rafał Miłecki
5e48c534f7 bcm47xx: fix bgmac support for BCM5358
Fix two long-standing regressions.

Fixes: https://github.com/openwrt/openwrt/issues/8278
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-27 11:11:01 +01:00
Rafał Miłecki
8457636868 bcm47xx: add pending devices support
This includes Lines E2500 V2 and Huawei B593u-12.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-27 09:10:40 +01:00
Rafał Miłecki
b894fbdfe0 bcm47xx: reorder MIPS BCM47XX patches
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-27 09:10:40 +01:00
Tim Harvey
026004d530 octeontx: add f2fs and ext4 support
Add both ext4 and f2fs support for overlayfs. The fstools mount_root
application will choose f2fs if the overlay volume space available
exceeds 100MB, otherwise ext4 is used.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-02-26 22:22:48 +01:00
Tim Harvey
fb2480df36 octeontx: add default packages for on-board devices
The Gateworks Newport boards supported by the octeontx target have
the following on-board devices:
 - Gateworks System Controller
 - GPIO buttons
 - GPIO leds
 - GPS PPS
 - Accelerometer
 - MCP251X CAN controller

Add kernel drivers for these devices in DEFAULT_PACKAGES

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-02-26 22:22:48 +01:00
Tomasz Maciej Nowak
43c7132bf8 ath79: add support for MikroTik RouterBOARD 911 Lite2/Lite5
Forward-port from ar71xx target the board introduced in commit
eb9e3651dd (" ar71xx: add support for the MikroTik RB911-2Hn/5Hn
boards"). Citing:

The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:

  https://mikrotik.com/product/RB911-2Hn
  https://mikrotik.com/product/RB911-5Hn

The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.

Specifications:
  * SoC: Atheros AR9344 (600MHz)
  * RAM: 64MiB
  * Storage: 16 MiB SPI NOR flash
  * Ethernet: 1x100M (Passive PoE in)
  * Wireless: AR9344 built-in wireless MAC, single chain
              802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)

Notes:
  * Older versions of these boards might be equipped with a NAND
    flash chip instead of the SPI NOR device. Those boards are not
    supported (yet).[1]
  * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
    same hardware. Support for that can be added later with little
    effort probably.[2]

End of citation.

Follow intallation instruction from that commit message, using
openwrt-ath79-mikrotik-mikrotik_routerboard-911-lite-initramfs-kernel.bin
and
openwrt-ath79-mikrotik-mikrotik_routerboard-911-lite-squashfs-sysupgrade.bin
images found in ath79/mikrotik directory. Be advised that the board
accepts 10-30 V on PoE input.

Known issues
Compared to ar71xx target image, there is still small leak of current to
user LED, which makes it lit, although weaker, even if brightness is set
to 0. The cause of that is still unknown.

1. https://github.com/openwrt/openwrt/pull/3652
2. RB911-5HnD should work with this commit or with [1], depending on
   what flash topology was used.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2023-02-26 22:22:48 +01:00
Tomasz Maciej Nowak
173d864253 ath79: mikrotik: stack ar9344 devices to single dtsi
Most of boards from MikroTik with AR9344 SoC (supported and
un-supported) replicate the same schematic, so stack common device nodes
to a single dtsi.

ar9344_mikrotik_routerboard-16m-nor.dtsi:
- remove include paragraph and wmac node, make it single nor flash node
  for others dts to include

ar9344_mikrotik_routerboard-lhg-5nd.dts:
- move all of the nodes to new file ar9344_mikrotik_routerboard.dtsi
  and leave only power, user and lan LEDs which differ from sxt-5nd-r2
  and other yet unsupported devices

ar9344_mikrotik_routerboard-sxt-5n.dtsi:
- remove, it made no sense to keep it, as only
  ar9344_mikrotik_routerboard-sxt-5nd-r2.dts included this file and
  added only compatible and model

ar9344_mikrotik_routerboard-sxt-5nd-r2.dts:
- include ar9344_mikrotik_routerboard.dtsi
- add nand gpio activating node, beeper, additional LEDs and flash chips
  which previously have been in ar9344_mikrotik_routerboard-sxt-5n.dtsi

ar9344_mikrotik_routerboard.dtsi:
- inherited most of the content from ar9344_mikrotik_routerboard-lhg-5nd.dts
  except three LEDs
- add wmac node, removed from ar9344_mikrotik_routerboard-16m-nor.dtsi

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2023-02-26 22:22:48 +01:00
Arınç ÜNAL
9df035b3ea treewide: remove label = "cpu" from DSA dt-binding
This is not used by the DSA dt-binding, so remove it from all devicetrees.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9cc115d8d6f73dd260de1609182f3645844d6907
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-26 22:22:48 +01:00
Linus Walleij
d51c44a3ba bcm53xx: Add D-Link DWL-8610AP board settings
The D-Link DWL-8610AP does not make use of the B53 switch
like most equipment. It lies dormant and the machine is using
eth0 and eth1 directly.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-02-26 22:22:48 +01:00
Linus Walleij
4d903a5009 bcm53xx: Add support for D-Link DWL-8610AP
The D-Link DWL-8610AP is a pretty straight-forward BC53016
device, D-Link has invented a firmware package format which
is a tar file, and we implement this for the factory image.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-02-26 22:22:48 +01:00
Jan-Niklas Burfeind
1e138ca703 sunxi: enable CONFIG_NVMEM_SYSFS
in both the stable and the testing kernel

h2+/h3/h5 devices have a Secure ID that can be read from
`/sys/bus/nvmem/devices/sunxi-sid0/nvmem`.
Enabling CONFIG_NVMEM_SYSFS grants sysfs access from userspace.

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2023-02-26 22:22:48 +01:00
Tomasz Maciej Nowak
909cc6ef5f x86: remove bootloader upgrade from preinit
This hack was to bring all existing installations to the newest GRUB
version as fast as possible. Since 19.07.x is EoL we can assume this
task is completed. Now sysupgrade will solely be responsible for
bootloader upgrade.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2023-02-26 22:22:48 +01:00
Daniel González Cabanelas
be0f1c1b26 mvebu: add support for Buffalo LinkStation LS220DE
The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell
Armada 370

Hardware:
   SoC:         Marvell Armada 88F6707
   CPU:         Cortex-A9 800 MHz, 1 core
   Flash 1:     SPI-NOR 1 MiB (U-Boot)
   Flash 2:     NAND 512 MiB (OS)
   RAM:         DDR3 256 MiB
   Ethernet:    1x 1GbE
   USB:         1x 2.0
   SATA:        2x 3Gb/s
   LEDs/Input:  5x / 2x (1x button, 1x slide-switch)
   Fan:         1x casing

Flash instructions, from hard drive:
  1. Get access to the "boot" partition at the hard drive where the stock
     firmware is installed. It can be done with acp-commander or by
     plugging the hard drive to a computer.
  2. Backup the stock uImage:
         mv /boot/uImage.buffalo /boot/uImage.buffalo.bak
  3. Move and rename the Openwrt initramfs image to the boot partition:
         mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo
  4. Power on the Linkstation with the hardrive inside. Now Openwrt will
     boot, but still not installed.
  5. Connect via ssh to OpenWrt:
         ssh root@192.168.1.1
  6. Rename boot files inside boot partition
         mount -t ext3 /dev/sda1 /mnt
         mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak
         mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak
  7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"):
         ubiformat /dev/mtd0 -y
         ubidetach -p /dev/mtd1
         ubiformat /dev/mtd1 -y
  8. Flash the sysupgrade image:
         sysupgrade -n openwrt-squashfs-sysupgrade.bin
  9. Wait until it finish, the device will reboot with OpenWrt installed
     on the NAND flash.

Restore the stock firmware:
  1. Take the hard drive used for the installation and restore boot backup
     files to their original names:
         mount -t ext3 /dev/sda1 /mnt
         mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo
         mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo
  2. Boot from the hard drive and perform a stock firmware update using
     the Buffalo utility. The NAND will be restored to the original
     state.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-02-26 22:22:48 +01:00
Tim Harvey
107f7374c9 octeontx: switch to Kernel 5.15
Switch over from testing version.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-02-26 18:15:33 +01:00
Karl Chan
5c04c3943e ramips: Alternative name Asus RT-AC750L for Asus RT-AC1200V2
The Asus RT-AC750L is identical to the already supported Asus RT-AC1200V2. Use the ALT0 buildroot tags to show both devices.

Reference : https://forum.openwrt.org/t/asus-rt-ac750l-is-the-same-as-rt-ac1200-v2/151783

Signed-off-by: Karl Chan <exkc@exkc.moe>
2023-02-26 17:46:27 +01:00
Daniel González Cabanelas
ed64c33235 ipq40xx: Linksys MR8300: fix the USB port power
The USB port on the MR8300 randomly fails to feed bus-powered devices.

This is caused by a misconfigured pinmux. The GPIO68 should be used to
enable the USB power (active low), but it's inside the NAND pinmux.

This GPIO pin was found in the original firmware at a startup script in
both MR8300 and EA8300. Therefore apply the fix for both boards.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2023-02-25 20:33:40 +01:00
Felix Baumann
688697889c ramips: correct the PCIe port number for some mt7621 devices
MT7621 uses a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Netgear R6220, WAC104 and WNDR3700 v5.

According to bootlog, MT7612E (5GHz) is connected to pcie0, and
MT7603E (2GHz) is connected to pcie2:
[2.758986] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
[2.772862] mt7621-pci 1e140000.pcie: PCIE0 enabled
[2.782579] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[3.009151] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[3.125715] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000

Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[felix.bau@gmx.de: adjust commit message for Netgear devices]
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-25 20:21:36 +01:00
Daniel Golle
aa41f4a395 mvebu: setup effective thermal zones on Puzzle M901 and M902
Assign fan with 4 active cooling levels to be used for the main CPU as
well as external SerDes units.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-02-25 19:01:40 +00:00
Daniel Golle
ea33a5def5 mvebu: puzzle: fix fan thermal cooling driver
Several fixes for the Puzzle WT61P803 hwmon driver were needed to make
it behave well as thermal cooling device:
 - wire-up cooling device with OF node in device tree
 - properly parse cooling-levels (u32 with range check vs. u8)
 - actually use cooling-levels
 - keep current state and only write to uC if state has changed
   (avoids flooding the uC with commands which will result in uC crashing)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-02-25 19:01:40 +00:00
Xinfa Deng
dd8a4a8c34 ath79: add support for GL.iNet GL-X1200
This patch adds supports for GL-X1200.

Specification:
	- SOC: QCA9563 (775MHz)
	- Flash: 16 MiB
	- RAM: 128 MiB DDR2
	- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
	- Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
	- SIM: 2x SIM card slots
	- MicroSD: 1x microSD slot
	- Antenna: 2x external 5dBi antennas
	- USB: 1x USB 2.0 port
	- Button: 1x reset button
	- LED: 16x LEDs (3x GPIO controllable)
	- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
	- OEM U-Boot supplies HTTP/GUI access

Implementation Notes
====================

Both the NOR and NAND variants boot off a NOR-based kernel,
consistent with the OEM's firmware.

The mode LEDs are
    * Boot, Running   system
    * Failsafe        2G
    * Upgrade         5G

Installation
============

Using sysupgrade
----------------

sysupgrade may be used to install a NAND image on a device running
a NAND image or a NOR image on a device running a NOR image. It is
recommended to *not* preserve config when upgrading from OEM firmware
or previous versions of OpenWrt. No supported sysupgrade path should
require "force". Transitioning from NOR to NAND can be accomplished

Using U-Boot
------------

The OEM U-Boot can be put into a graphical, firmware-upload mode by
holding down the button on the side of the router while applying power
and for a bit more than five seconds following with the current OEM
U-Boot. The power LED will come on, then the 5G LED will flash five
times, about once a second.  When the 5G LED stops flashing and the
2G LED lights solid, the router's U-Boot will provide an upload page
at http://192.168.1.1/ Either a browser may be used to upload an image,
or a utility such as curl may be used:

curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
         http://192.168.1.1/index.html
or
    curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
         http://192.168.1.1/index.html

Note that NOR vs. NAND is based on the file name extension.

Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
2023-02-25 14:31:42 +01:00
Rafał Miłecki
eaf5c85fd3 bcm47xx: switch default kernel to the 5.15
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-24 12:06:10 +01:00
Rafał Miłecki
ee85786b43 bcm47xx: relocate LZMA loader #2
Increased size of the 5.15 kernel requires bumping BZ_TEXT_START again.
Without this CFE hangs at the:
Starting program at 0x80001000

This fixes booting 5.15 based mips74k images on:
1. BCM4706 (Luxul XWR-1750)
2. BCM5357B0 (Linksys E1000 V2.1)
3. BCM47186B0 (Luxul XWR-600)
4. BCM5358 (Linksys E2500 V3)

It isn't needed but also doesn't break:
1. BCM5354 (Asus WL-500gP V2)

Ref: 4cd97e4760 ("bcm47xx: relocate LZMA loader")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-02-24 12:05:14 +01:00
Hauke Mehrtens
218f425b61 kernel: Add CONFIG_PPC_QUEUED_SPINLOCKS configuration option
The CONFIG_PPC_QUEUED_SPINLOCKS configuration option is not defined for
kernel 5.15, it is defined for kernel 5.10.

This fixes the compilation of mpc85xx/p2020 with kernel 5.15.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-02-23 22:22:27 +01:00
Rafał Miłecki
b4ae914037 kernel: backport NVMEM late fixes from v6.2
They were backported to stable kernels but we backport more stuff on our
own so we have to pick up few remaining.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-23 09:50:01 +01:00
Nick Hainke
9837f81bae mpc85xx: switch default kernel to 5.15
The default kernel should be switched to 5.15 in order to enable testing
by a broader audience.

Tested on TP-Link TL-WDR4900 v1.

Acked-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-02-22 23:39:01 +01:00
Robert Marko
00c5276659
mvebu: mochabin: enlarge PCI memory window
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.

So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.

This has been already sent upstream [1].
[1] https://lore.kernel.org/linux-arm-kernel/20230219121418.1395401-1-robert.marko@sartura.hr/

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-02-21 17:15:40 +01:00
Rafał Miłecki
52ddb38469 kernel: update NVMEM subsystem to the v6.3
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-21 11:58:47 +01:00
Pawel Dembicki
bfa5e4e4eb
mcp85xx: Switch TP-Link TL-WDR4900 v1 to DSA
This patch introduces DSA support for TP-Link TL-WDR4900 v1 switch.
Swconfig driver for QCA8327 switch is removed because this router is
only one device which use Qualcom swconfig switch.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Nick Hainke <vincent@systemli.org> # TP Link WDR4900 v1 (5.15)
2023-02-20 12:04:44 +01:00
Pawel Dembicki
f56ef4c040
mpc85xx: refresh kernel config
It was done by "make kernel_oldconfig" command for 5.10 and 5.15.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2023-02-20 12:04:43 +01:00
Andre Heider
7ae4716243 toolchain: remove installing twice in the "initial" subdir
This was apparently introduced to recreate the toolchain (wipe
staging_dir/toolchain*, but keep build_dir/toolchain*, followed by a
`make toolchain/compile`).

But it leaves leftovers and causes re-links to happen at src_install phase,
because of the changed paths, possibly adding yet another source of issues.

With the prior commits removing various hacks related to the "initial"
folder we can remove installing it twice altogether.

The recreated toolchain is exactly the same as before.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-02-19 19:44:39 +01:00
Shiji Yang
68004f1942 ramips: add alternative device name for Wiflyer WF3526-P
Wiflyer WF3526-P and Zbtlink ZBT-WE1326 have the same circuit design.
Installing the misunderstading firmware of ZBT-WE3526 will cause Wi-Fi
not work due to allocate the wrong pcie port. Add alternative name to
help users easily build or download the correct firmware.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-02-19 18:37:55 +01:00
Shiji Yang
c77913be5b ramips: correct the PCIe port number for Zbtlink ZBT-WE1326
MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Zbtlink ZBT-WE1326.

According to the bootlog, MT7612E (5 GHz) is connected to pcie1, and
MT7603E (2 GHz) is connected to pcie2:
[4.197658] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[4.204609] mt7621-pci 1e140000.pcie: PCIE1 enabled
[4.209476] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[4.307988] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[4.367206] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-02-19 18:37:55 +01:00
Christian Marangi
01262c921c
tools/squashfs: rename to squashfs3-lzma
The name of squashfs is confusing since in reality it's a really old
version using an old lzma library. This tools is used for old ath79
netgear target and to produde a fake squasfs3 image needed for some
specific bootloader from some OEM (AVM for example)

Rename squashfs tool to squasfs3-lzma to better describe it.
Rename the installed bin from mksquashfs-lzma to mksquashfs3-lzma.
Use tar transform to migrate the root directory in tar to the new
naming.
Drop redundant PKG_CAT variable not needed anymore.
Also update any user of this tool.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-02-18 21:11:36 +01:00
Brian Norris
46ea81ba99 ipq40xx: chromium: Enable kmod-ramoops by default
Chromium devices (like Google WiFi) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-02-18 19:58:22 +01:00
Brian Norris
a79abd813d ipq806x: chromium: Enable kmod-ramoops by default
Chromium devices (like OnHub) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-02-18 19:58:22 +01:00
Arınç ÜNAL
efbb623deb ramips: add support for Huasifei WS1208V2
The Huasifei WS1208V2 is an AC1200 router featuring 5 Ethernet ports with a
Quectel RM520N-GL cellular modem which supports QMI and MBIM modes.

Specifications:
- MT7621AT, 256 MiB RAM, 16 MiB SPI Flash
- MT7603EN 2.4 GHz & MT7612EN 5 GHz WLAN
- Quectel RM520N-GL Cellular Modem
- 2 WLAN & 4 Cellular Antennas
- 5 Gigabit Ethernet Ports
- 1 USB 2.0 port
- 1 PCI-E Slot
- 1 M.2 slot
- 1 SIM card slot
- 1 SD card slot

Installation:
- Install sysupgrade image via ROOter OS.

TFTP Recovery:
- Connect to serial console.
- Boot initramfs image by choosing option 1 when U-Boot prompts.
- Install sysupgrade image via OpenWrt.

Link: https://www.huasifei.com/a/Products/5G%20CPE/240.html
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-18 19:56:37 +01:00
John Audia
461072fc7b kernel: bump 5.10 to 5.10.168
Manually rebased:
  backport-5.10/804-v5.14-0001-nvmem-core-allow-specifying-of_node.patch

Removed upstreamed:
  generic-backport/807-v5.17-0003-nvmem-core-Fix-a-conflict-between-MTD-and-NVMEM-on-w.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.168&id=34ec4c7831c416ac56619477f1701986634a7efc

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-18 17:41:23 +01:00
Michael Pratt
6f6d24a00a ramips: add label MAC address for EPG600 and ESR600
set label mac for the current ESR600 and new EPG600
using the board.d scripts

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Michael Pratt
4ef86c620f ramips: add support for Senao Engenius EPG600
FCC ID: A8J-EPG600

Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)

this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.

**Specification:**

  - MT7620 SOC		MIPS 24kec, 2.4 GHz WMAC, 2x2
  - RT5592N WLAN	PCI chip, 5 GHz, 2x2
  - QCA8337N Gb SW	RGMII GbE, SW P0 -- SOC P5, 5 LEDs
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 64 MB RAM		NT5TU32M16
  - UART console	J2, populated
  - USB 2.0 port	direct to SOC
  - 6 GPIO LEDs		power, 2G, 5G, wps2g, wps5g, line
  - 3 buttons		reset, wps, "reg" (registeration)
  - 4 antennas		internal omni-directional plates

NOT YET SUPPORTED: VoIP

  - Si3050-FT + Si3019-FT	Voice DAA, SPI control, PCM data
  - Phone Ports "TEL", "LINE"	RJ11, 4P2C (2 pins)

**MAC addresses:**

  MAC address labeled as MAC ADDRESS
  MACs present in both wifi cal data and uboot environment

  eth0.1/phy1	----	*:82	rf 0x4
  phy0		----	*:83	factory 0x4
  eth0.2	MAC	*:b8	"wanaddr"

**Installation:**

  Method 1: Firmware upgrade page:

    (if you cannot access the APs webpage)
    factory reset with the reset button
    connect ethernet to a computer
    OEM webpage at 192.168.0.1
    username and password 'admin'

    Navigate to gear icon, "Device Management", "Tools"
    select the factory.dlf image
    Upload and verify checksum

  Method 2: Serial to upload initramfs:

    Follow directions for TFTP recovery
    upload and boot initramfs and do a sysupgrade

**TFTP recovery:**

  Requires UART serial console, reset button does nothing

  rename initramfs-kernel.bin to 'uImageEPG600'
  make available on TFTP server at 192.168.99.8
  power board, interrupt boot with "4"
  execute `tftpboot` and `bootm` (with the load address)

**Return to OEM:**

  Images from OEM are provided, but not compatible
  with openwrt sysupgrade. So it must be modified.

  Alternatively, back up all mtd partitions before flashing

**Note on switch registers:**

  The necessary registers needed for the QCA8337 switch
  can be read from interrupted boot (tftpboot, bootm)
  by using the following lines in the switch driver ar8327.c
  in the function 'ar8327_hw_config_of'
  where 'qca,ar8327-initvals' is parsed from DTS
  before the new register values are written:

    pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
    pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
    pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
    pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Michael Pratt
6b07d0c077 ramips: mt7620: split gsw hw_init to mac_init, ephy_init
in order for the option ephy-disable to work
without also needing ephy-base option,
we have to skip all the lines that write to mdio addresses that
assume those addresses do not have an external switch.

Otherwise, ephy ports will be disabled in hardware,
but register writes still happen as if they are enabled.

Split the functions so that other things are done first,
and ephy port setup can be skipped with a simple "return".

Tested on Engenius EPG600 (MT7620A ver:2 eco:3)
with QCA8337 external switch

Ref: cc6fd6fbb5 ("ramips: mt7620: add ephy-disable option to switch driver")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Karol Przybylski
71a22ef175 ipq807x: Add bluetooth driver to zyxel nbg7815
Zyxel NBG7815 supports bluetooth with blsp1_uart3.
Configuration are already added to dts file, device needs only module to working bluetooth properly.
Tested at below posts:
https://forum.openwrt.org/t/openwrt-support-for-armor-g5-nbg7815/98598/259?u=itork

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Karol Przybylski <karol.przybylski@esm-technology.pl>
2023-02-18 16:23:31 +01:00
Karl Chan
8ef81b4a19 ramips: fix the name of ASUS AX54 because it has dupilcated twice
The name of ASUS AX54 has dupilcated in the DEVICE_ALT0_VENDOR/DEVICE_ALT0_MODEL

Signed-off-by: Karl Chan <exkc@exkc.moe>
2023-02-18 16:01:30 +01:00
Marcel Ziswiler
f6d2a23cbc mediatek: add support for Netgear WAX206
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
  * 2.4 GHz: MediaTek MT7622BV
  * 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
            1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
             Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
        115200n8
* Power: 12 VDC, 2.5 A

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
  setenv ipaddr 192.168.1.1
  setenv serverip 192.168.1.100
  tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
  bootm

Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
  moment. If connected to a multi-gig port the speed has to be manually
  set to 1G/full either for the switch port or in OpenWrt. For example
  add the following to /etc/rc.local to set it on boot:
  /usr/sbin/ethtool -s wan speed 1000 duplex full

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar

* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
  DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
  Image creation code for this device

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2023-02-18 15:46:45 +01:00
John Audia
4536c76b55 kernel: bump 5.15 to 5.15.94
Patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-18 15:06:04 +01:00
Shiji Yang
748f7f1b9c ramips: backport mt7621 PCIs initialization delay patch
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Some devices like ZBT WE1326 and ZBT WF3526-P and some Netgear models need
to delay phy port initialization after calling the mt7621_pcie_init_port()
driver function to get into reliable boots for both warm and hard resets.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-02-18 11:41:54 +02:00
Paul Spooren
c0683ec458 kernel: 5.15: refresh patches
This commit fixes the following commit

    f584fb2f7e kernel: import accepted MediaTek Ethernet patches

Unrefreshed patches caused the CI to fail.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2023-02-17 18:30:30 +01:00
Christian Marangi
86ecf7bd39
Revert "ipq806x: disable ea8500 image by default"
This reverts commit c4a9a67de8.

Device is now fixed and works correctly with kernel 5.15.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-02-17 04:27:16 +01:00
Christian Marangi
e12ff74ba1
Revert "ipq806x: disable ea8500 image by default"
This reverts commit 5384c9337f.

Device is now fixed and works correctly with kernel 5.15.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-02-17 04:27:15 +01:00
Christian Marangi
2ddf479cc7
ipq806x: 5.10: refresh patches
Refresh patches for kernel 5.10

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-02-17 04:27:15 +01:00
Christian Marangi
9a24040d20
ipq806x: fix Linksys EAX500 family devices dead Ethernet switch
With 5.15 kernel version Linksys EAX500 family devices suffered from a
big regression where the Ethernet switch became silent and started to
malfunction.

It was discovered later that the cause was not really the kernel upgrade
itself but a hackish implementation of the hw implementation of these
special routers.

In the original Linksys source code, GPIO 63 was handled in a special way
and was reset on reboot.

Normally GPIO 63 is used for pcie2 reset but in every device we support,
pcie2 is actually never used as nothing is attached to it.

Linksys rerouted GPIO 63 to the switch reset pin and deviates from
common hw implementation.

Till now it was used an hack to handle this case... It was set pcie3 as
working (while actually nothing was connected), set it to output low
(for assert-deassert from the pcie init code) and be done with it.
The result was that the GPIO was reset for enough time in early boot and
everything worked correctly.
This hack implementation was born to fail from the very start and in
kernel 5.15 finally problem arised.

In 5.15 pcie code changed and now the GPIO reset pin is not asserted as
probe won't fail if nothing is connected to the line (the old behaviour)
This result in the switch hold the reset pin and the Ethernet switch
dead.

On top of that with 5.15 code got optimized and simply attaching the
GPIO reset to the mdio wasn't enough as the switch require at least 10ms
to be correctly reset.

So implement finally a correct solution where:
- pcie2 is correctly disabled (nothing attached, unused)
- drop the wrong output-low for pcie2 reset pin
- define GPIO 63 as switch reset
- Add the reset-gpios to the mdio0 node
- Set the reset-post-delay-us to 12ms to correctly give time the switch
  to reset

Fixes: #10983
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-02-17 04:27:15 +01:00
Rodrigo B. de Sousa Martins
77d061167c ramips: Switch default kernel to 5.15
I tested kernel 5.15 on my device for several times without any problems.
In my tests, 5.15 kernel has performance improvements such MGLRU.
Finally, initial kernel 6.1 support is imminent. All ramips subtargets have
5.15 as testing kernel. So, it's time to change.

Tested on my Archer C6 v3.2 (mt7621)

Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
[reformat commit subject and message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2023-02-17 16:31:53 +02:00
Mikhail Zhilkin
51e5f22096 ramips: fix wrong pcie port number for Arcadyan devices
Wrong pcie port number for WLAN causes missing 5g WLAN interface with 5.15
kernel. This changes port from pcie0 to pcie1 in dtsi.

[1.166330] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[1.180073] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[1.193889] mt7621-pci 1e140000.pcie: PCIE1 enabled

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-02-17 16:30:32 +02:00
Robert Marko
8c3bcc1989
ipq807x: move AQR driver from built-in to kmod
ipq807x does not compile-in hwmon core, and this is leading to the hwmon
code in AQR driver not being compiled due to IS_REACHABLE(CONFIG_HWMON)
evaluating to false as hwmon is being built as a module.

So, lets not compile-in Aquantia PHY driver so it can be included as kmod
instead to have functioning hwmon.

This allows using the thermal sensors in AQR-s as thermal zones for
cooling devices like fans.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-02-15 23:29:01 +01:00
Rafał Miłecki
f06bd5bdb8 bcm4908: refactor packet steering init
Replace a standalone init.d script with a platform implementation as
supported by netifd. This avoids a race between netifd and target
specific setups.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-15 19:44:11 +01:00
Rafał Miłecki
56a93f9873 bcm53xx: fix shebang in packet_steering.sh
Fixes: 6e555ac3ad ("bcm53xx: refactor packet steering init")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-15 19:44:11 +01:00
Rafał Miłecki
6e555ac3ad bcm53xx: refactor packet steering init
Replace a standalone init.d script with a platform implementation as
supported by netifd. This avoids a race between netifd and target
specific setups.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-15 14:25:57 +01:00
Daniel Golle
f584fb2f7e kernel: import accepted MediaTek Ethernet patches
Import some accepted and pending upstream patches for mtk_eth_soc,
replacing some semantically equivalent local patches and fixing issues
when operating the PCS in 1G SGMII mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-02-15 03:28:09 +00:00
Daniel Golle
80196f4e3c mediatek: mtk_thermal: replace with upstream patch
Replace local patch adding thermal support for MT7986 with version
accepted upstream.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-02-15 03:28:09 +00:00
Daniel Golle
e8625c89ef treewide: replace /sys/devices/virtual/ubi by /sys/class/ubi
Starting from Linux Kernel version 6.3 UBI devices will no longer be
considered virtual, but rather have an MTD device parent. Hence they
will no longer be listed under /sys/devices/virtual/ubi which is
used in multiple places in OpenWrt. Prepare for future kernels by
using /sys/class/ubi instead of /sys/devuces/virtual/ubi.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-02-15 03:27:59 +00:00
INAGAKI Hiroshi
f490295bf2
ipq807x: add support for Buffalo WXR-5950AX12
Buffalo WXR-5950AX12 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ8074A.

Specification:

- SoC         : Qualcomm IPQ8074A
- RAM         : DDR3 1024 MiB (2x Nanya NT5CC256M16ER-EK)
- Flash       : RAW NAND 256 MiB (Winbond W29N02GZBIBA)
- WLAN        : 2.4/5 GHz (IPQ8074A)
- Ethernet    : 5 ports
  - WAN       : 100/1000/2500/10000 Mbps x1 (AQR113C)
  - LAN       : 100/1000/2500/10000 Mbps x1 (AQR113C),
                10/100/1000 Mbps x3 (QCA8075)
- LED/Keys    : 8x/5x
- UART        : pin header on PCB (J7)
  - assignment: 3.3V, GND, TX, RX from disc marking
  - settings  : 115200n8
- Power       : 12 VDC, 4 A

Flash instruction using initramfs image:

1. Prepare TFTP server with IP address 192.168.11.10
2. Rename OpenWrt initramfs image to "WXR-5950AX12-initramfs.uImage and
   place it to TFTP directory
3. Hold AOSS (WPS) button and power on WXR-5950AX12
4. WXR-5950AX12 downloads initramfs image from TFTP server and boots
   with it automatically
5. Upload sysupgrade image to WXR-5950AX12 and perform sysupgrade
6. Wait ~120 seconds to complete flashing

Partition layout:

0x000000000000-0x000000100000 : "0:sbl1"
0x000000100000-0x000000200000 : "0:mibib"
0x000000200000-0x000000280000 : "0:bootconfig"
0x000000280000-0x000000300000 : "0:bootconfig1"
0x000000300000-0x000000600000 : "0:qsee"
0x000000600000-0x000000900000 : "0:qsee_1"
0x000000900000-0x000000980000 : "0:devcfg"
0x000000980000-0x000000a00000 : "0:devcfg_1"
0x000000a00000-0x000000a80000 : "0:apdp"
0x000000a80000-0x000000b00000 : "0:apdp_1"
0x000000b00000-0x000000b80000 : "0:rpm"
0x000000b80000-0x000000c00000 : "0:rpm_1"
0x000000c00000-0x000000c80000 : "0:cdt"
0x000000c80000-0x000000d00000 : "0:cdt_1"
0x000000d00000-0x000000d80000 : "0:appsblenv"
0x000000d80000-0x000000e80000 : "0:appsbl"
0x000000e80000-0x000000f80000 : "0:appsbl_1"
0x000000f80000-0x000001000000 : "0:art"
0x000001000000-0x000001080000 : "0:art_1"
0x000001080000-0x000001100000 : "0:orgdata"
0x000001100000-0x000001180000 : "0:orgdata_1"
0x000001180000-0x000005180000 : "rootfs"
0x000005180000-0x000009180000 : "rootfs_recover"
0x000009180000-0x000010000000 : "user_property"

Notes:

- WXR-5950AX12 has 2x OS images on NAND flash. The 1st image is for
  normal operation and the 2nd one is for recoverying or firmware
  upgrading on stock.

- Stock U-Boot checks MD5 hashes in "fw_hash" volume in each "root*"
  partition when booting. This is just a comparation of hash strings.

  Behaviors:

  - both "fw_hash" volumes exist, hashes are rootfs == rootfs_recover
    ---> boot from rootfs

  - both "fw_hash" volumes exist, hashes are rootfs != rootfs_recover
    ---> boot from rootfs_recover

    Note: this behavior is used for firmware upgrading on stock

  - "fw_hash" volume in rootfs is missing
    ---> boot from rootfs_recover

  - "fw_hash" volume in rootfs_recover is missing
    ---> boot from rootfs

  - "fw_hash" volumes in both root* partition are missing
    ---> boot from rootfs_recover

Reverting to stock firmware:

1. Decrypt official image by buffalo-enc and remove header

   example of decryption:

   $ buffalo-enc -i wxr_5950ax12_jp_305 -o wxr_5950ax12_jp_305.dec \
                 -d -k olaffuB -O 0xc8

   example of removing header (v3.05):

   - before

   $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.dec
   00000000  57 58 52 2d 35 39 35 30  41 58 31 32 5f 33 2e 30  |WXR-5950AX12_3.0|
   00000010  35 5f 31 2e 30 31 5f 4a  50 5f 6a 70 5f 71 63 61  |5_1.01_JP_jp_qca|
   00000020  0a 66 69 6c 65 6c 65 6e  3d 34 35 33 35 30 39 31  |.filelen=4535091|
   00000030  32 0a 55 42 49 23 01 00  00 00 00 00 00 00 00 00  |2.UBI#..........|
   00000040

   - after

   $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.ubi
   00000000  55 42 49 23 01 00 00 00  00 00 00 00 00 00 00 00  |UBI#............|
   00000010  00 00 08 00 00 00 10 00  78 cf c4 91 00 00 00 00  |........x.......|
   00000020  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
   00000030  00 00 00 00 00 00 00 00  00 00 00 00 3d 2a 64 fd  |............=*d.|
   00000040

2. Boot WXR-5950AX12 with OpenWrt initramfs image

3. Upload modified stock image to WXR-5950AX12

4. Find partitions "rootfs" and "rootfs_recover"

   example:

   root@OpenWrt:/# cat /proc/mtd
   dev:    size   erasesize  name
   ...
   mtd22: 04000000 00020000 "rootfs"
   mtd23: 04000000 00020000 "rootfs_recover"
   ...

   in this case, "rootfs" is mtd22 and "rootfs_recover" is mtd23

5. Format "rootfs"/"rootfs_recover" partition with the uploaded image

   example:

   ubiformat /dev/mtd22 -f /tmp/wxr_5950ax12_jp_305.ubi
   ubiformat /dev/mtd23 -f /tmp/wxr_5950ax12_jp_305.ubi

6. Remove "rootfs"/"rootfs_data" volume from user_property partition

   example:

   . /lib/upgrade/nand.sh
   UBI=$(nand_attach_ubi user_property)
   ubirmvol /dev/$UBI -N rootfs
   ubirmvol /dev/$UBI -N rootfs_data

7. Reboot

MAC addresses:

LAN    : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text))
WAN    : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text))
2.4 GHz: 50:C4:DD:xx:xx:30 (0:APPSBLENV, wlan0addr (text))
5 GHz  : 50:C4:DD:xx:xx:38 (0:APPSBLENV, wlan1addr (text))

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-02-12 01:18:39 +01:00
INAGAKI Hiroshi
d256c0bfd7
ipq807x: merge duplicate network configurations in 02_network
Merge network configurations in 02_network of Dynalink DL-WRX36 and
Xiaomi AX9000.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-02-12 01:18:39 +01:00
INAGAKI Hiroshi
f5d962f9b3
ipq807x: enable regulator-fixed driver
Enable regulator-fixed to define the regulator of USB vbus on Buffalo
WXR-5950AX12.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-02-12 01:18:35 +01:00
INAGAKI Hiroshi
5163bb5e54 realtek: add support for APRESIA ApresiaLightGS120GT-SS
APRESIA ApresiaLightGS120GT-SS (APLGS120GTSS) is a 16 + 4 ports gigabit
switch, based on RTL8382M.

Specifications:

- SoC          : Realtek RTL8382M
- RAM          : DDR3 256 MiB (Nanya NT5CC256M8JQ-EK)
- Flash        : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet     : 10/100/1000 Mbps x16 + 4
  - port  1-8  : RTL8218B
  - port  9-16 : RTL8382M, TP (SoC, RTL8218B)
  - port 17-20 : RTL8214FC, TP/SFP (Combo)
- LEDs/Keys    : 3x/1x
- UART         : through-hole on PCB
  - J6: 3.3V, TX, RX, GND from tri-angle marking side
  - 115200n8
- Power        : 100-120/200-240 VAC, 50/60 Hz
                 Max. 16 W, Avg 14 W (100 VAC)
  - Plug       : IEC 60320-C13

Flash instruction using factory image:

1. Boot ApresiaLightGS120GT-SS normally
2. Login to WebUI and open firmware page ("ファームウェア")
3. If the device is booted from image1, set active image for next
   booting ("起動イメージ選択") to image2("イメージ2"), press apply
   ("適用") button and reboot the device to make booting from image2
4. On the WebUI, set active image to image1
5. Select the OpenWrt factory image and press update button ("更新")
6. Open reboot page ("再起動") and press reboot button ("再起動実行")

Notes:

- "ApresiaLightGS120GT-SS" is a model name and "APLGS120GTSS" is a model
  number

- this device has 3x GPIO-controlled LEDs on PCB, but 1x LED
  ("green:unused") has no hole on the case

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-02-13 12:22:17 +01:00
INAGAKI Hiroshi
5b33916c0a realtek: add common definition of cameo based firmware
The cameo-related recipes can also be used for APRESIA ApresiaLightGS
series devices. So create common definition for the devices manufactured
by Cameo.
And also, the model name of ApresiaLightGS120GT-SS is too long for cameo
header (max: 20 bytes), so use additional variable "CAMEO_BOARD_MODEL"
in Build/cameo-headers instead of DEVICE_MODEL to use the custom name.
(default of CAMEO_BOARD_MODEL: DEVICE_MODEL)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-02-13 12:22:17 +01:00
INAGAKI Hiroshi
d76f0f407b realtek: rename cameo specific names in "Build/*" definitions
This patch renames some Cameo specific definitions for image generation.
The same format is also used on APRESIA ApresiaLightGS series devices, not
D-Link specific.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-02-13 12:22:17 +01:00
Jan Hoffmann
65b2bcbf5f realtek: fix memory leak in netevent handler
The net_event_work struct is allocated, but only freed in a single case.
Move the allocation to the branch where it is actually needed, and free
it after the work has been done.

Fixes: 03e1d93e07 ("realtek: add driver support for routing offload")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2023-02-13 12:14:16 +01:00
Felix Fietkau
1352e5da8d kernel: add missing optimization for page pool
Improves performance in combination with threaded NAPI

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-13 11:48:55 +01:00
Karl Chan
92276eef70 ramips: add support for ASUS RT-AX54
Specifications:
- Device: ASUS RT-AX54 (AX1800S/HP,AX54HP)
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x POWER (blue, configurable)
        1x LAN (blue, configurable)
        1x WAN (blue, configurable)
	1x 2.4G (blue, not configurable)
	1x 5G (blue, not configurable)

Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
   Select "2. Upgrade firmware"
   Press enter when show "Run firmware after upgrading? (Y/n):"
   Select 0 for TFTP method
   Input U-Boot's IP address: 192.168.1.1
   Input TFTP server's IP address: 192.168.1.2
   Input IP netmask: 255.255.255.0
   Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"

Signed-off-by: Karl Chan <exkc@exkc.moe>
2023-02-12 18:27:45 +01:00
Michael Pratt
51982560a9 ath79: bump SPI frequency of Senao qca955x routers
All boards using this DTSI are expected to have
the same 16 MB MX25L12845EMI-10G flash chip,
or a larger one which can also use 40 MHz frequency.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-12 18:07:31 +01:00
Michael Pratt
5e973dd61f ath79: add eth0 mac and initvals for Engenius EPG5000
Although VLANs are used, the "eth0" device by itself
does not have a valid MAC, so fix that with preinit script.

More initvals added by editing the driver to print switch registers,
after the bootloader sets them but before openwrt changes them.

The register bits needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by adding print lines in the switch driver ar8327.c
before 'qca,ar8327-initvals' is parsed from DTS and written
for example:

  pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-12 18:07:31 +01:00
Michael Pratt
f545caf001 ath79: convert Engenius EPG5000 radios to nvmem-cells
Use nvmem kernel subsystem to pull radio calibration data
with the devicetree instead of userspace scripts.

Existing blocks for caldata_extract are reordered alphabetically.

MAC address is set using the hotplug script.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-12 18:07:31 +01:00
Michael Pratt
f9c28222c8 ath79: add support for Senao Engenius ESR1200
FCC ID: A8J-ESR900

Engenius ESR1200 is an indoor wireless router with
a gigabit ethernet switch, dual-band wireless,
internal antenna plates, and a USB 2.0 port

**Specification:**

  - QCA9557 SOC		2.4 GHz, 2x2
  - QCA9882 WLAN	PCIe mini card, 5 GHz, 2x2
  - QCA8337N SW		4 ports LAN, 1 port WAN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM
  - UART at J1		populated, RX grounded
  - 6 internal antenna plates (omni-directional)
  - 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset)

**MAC addresses:**

  Base MAC address labeled as "MAC ADDRESS"
  MAC "wanaddr" is not similar to "ethaddr"

  eth0 *:c8 MAC u-boot-env ethaddr
  phy0 *:c8 MAC u-boot-env ethaddr
  phy1 *:c9 --- u-boot-env ethaddr +1
  WAN  *:66:44  u-boot-env wanaddr

**Serial Access:**

  RX on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin

**Installation:**

  Method 1: Firmware upgrade page

    OEM webpage at 192.168.0.1
    username and password "admin"
    Navigate to Settings (gear icon) --> Tools --> Firmware
    select the factory.bin image
    confirm and wait 3 minutes

  Method 2: TFTP recovery

    Follow TFTP instructions using initramfs.bin
    use sysupgrade.bin to flash using openwrt web interface

**Return to OEM:**

  MTD partitions should be backed up before flashing
  using TFTP to boot openwrt without overwriting flash

  Alternatively, it is possible to edit OEM firmware images
  to flash MTD partitions in openwrt to restore OEM firmware
  by removing the OEM header and writing the rest to "firmware"

**TFTP recovery:**

  Requires serial console, reset button does nothing at boot

  rename initramfs.bin to 'uImageESR1200'
  make available on TFTP server at 192.168.99.8
  power board, interrupt boot by pressing '4' rapidly
  execute tftpboot and bootm

**Note on ETH switch registers**

  Registers must be written to the ethernet switch
  in order to set up the switch's MAC interface.
  U-boot can write the registers on it's own
  which is needed, for example, in a TFTP transfer.

  The register bits from OEM for the QCA8337 switch
  can be read from interrupted boot (tftpboot, bootm)
  by adding print lines in the switch driver ar8327.c
  before 'qca,ar8327-initvals' is parsed from DTS and written.
  for example:

    pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-12 18:07:31 +01:00
Michael Pratt
96c2119dba ath79: add support for Senao Engenius ESR1750
FCC ID: A8J-ESR1750

Engenius ESR1750 is an indoor wireless router with
a gigabit ethernet switch, dual-band wireless,
internal antenna plates, and a USB 2.0 port

**Specification:**

  - QCA9558 SOC		2.4 GHz, 3x3
  - QCA9880 WLAN	PCIe mini card, 5 GHz, 3x3
  - QCA8337N SW		4 ports LAN, 1 port WAN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM
  - UART at J1		populated, RX grounded
  - 6 internal antenna plates (omni-directional)
  - 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset)

**MAC addresses:**

  Base MAC address labeled as "MAC ADDRESS"
  MAC "wanaddr" is similar to "ethaddr"

  eth0 *:58 MAC u-boot-env ethaddr
  phy0 *:58 MAC u-boot-env ethaddr
  phy1 *:59 --- u-boot-env ethaddr +1
  WAN  *:10:58  u-boot-env wanaddr

**Serial Access:**

  RX on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin

**Installation:**

  Method 1: Firmware upgrade page

    NOTE: ESR1750 might require the factory.bin
      for ESR1200 instead, OEM provides 1 image for both.

    OEM webpage at 192.168.0.1
    username and password "admin"
    Navigate to Settings (gear icon) --> Tools --> Firmware
    select the factory.bin image
    confirm and wait 3 minutes

  Method 2: TFTP recovery

    Follow TFTP instructions using initramfs.bin
    use sysupgrade.bin to flash using openwrt web interface

**Return to OEM:**

  MTD partitions should be backed up before flashing
  using TFTP to boot openwrt without overwriting flash

  Alternatively, it is possible to edit OEM firmware images
  to flash MTD partitions in openwrt to restore OEM firmware
  by removing the OEM header and writing the rest to "firmware"

**TFTP recovery:**

  Requires serial console, reset button does nothing at boot

  rename initramfs.bin to 'uImageESR1200'
  make available on TFTP server at 192.168.99.8
  power board, interrupt boot by pressing '4' rapidly
  execute tftpboot and bootm

**Note on ETH switch registers**

  Registers must be written to the ethernet switch
  in order to set up the switch's MAC interface.
  U-boot can write the registers on it's own
  which is needed, for example, in a TFTP transfer.

  The register bits from OEM for the QCA8337 switch
  can be read from interrupted boot (tftpboot, bootm)
  by adding print lines in the switch driver ar8327.c
  before 'qca,ar8327-initvals' is parsed from DTS and written.
  for example:

    pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-12 18:07:31 +01:00
Michael Pratt
2f99f7e2d0 ath79: add support for Senao Engenius ESR900
FCC ID: A8J-ESR900

Engenius ESR900 is an indoor wireless router with
a gigabit ethernet switch, dual-band wireless,
internal antenna plates, and a USB 2.0 port

**Specification:**

  - QCA9558 SOC		2.4 GHz, 3x3
  - AR9580 WLAN		PCIe on board, 5 GHz, 3x3
  - AR8327N SW		4 ports LAN, 1 port WAN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM
  - UART at J1		populated, RX grounded
  - 6 internal antenna plates (omni-directional)
  - 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset)

**MAC addresses:**

  Base MAC address labeled as "MAC ADDRESS"
  MAC "wanaddr" is not similar to "ethaddr"

  eth0 *:06 MAC u-boot-env ethaddr
  phy0 *:06 MAC u-boot-env ethaddr
  phy1 *:07 --- u-boot-env ethaddr +1
  WAN  *:6E:81  u-boot-env wanaddr

**Serial Access:**

  RX on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin

**Installation:**

  Method 1: Firmware upgrade page

    OEM webpage at 192.168.0.1
    username and password "admin"
    Navigate to Settings (gear icon) --> Tools --> Firmware
    select the factory.bin image
    confirm and wait 3 minutes

  Method 2: TFTP recovery

    Follow TFTP instructions using initramfs.bin
    use sysupgrade.bin to flash using openwrt web interface

**Return to OEM:**

  MTD partitions should be backed up before flashing
  using TFTP to boot openwrt without overwriting flash

  Alternatively, it is possible to edit OEM firmware images
  to flash MTD partitions in openwrt to restore OEM firmware
  by removing the OEM header and writing the rest to "firmware"

**TFTP recovery:**

  Requires serial console, reset button does nothing at boot

  rename initramfs.bin to 'uImageESR900'
  make available on TFTP server at 192.168.99.8
  power board, interrupt boot by pressing '4' rapidly
  execute tftpboot and bootm

**Note on ETH switch registers**

  Registers must be written to the ethernet switch
  in order to set up the switch's MAC interface.
  U-boot can write the registers on it's own
  which is needed, for example, in a TFTP transfer.

  The register bits from OEM for the AR8327 switch
  can be read from interrupted boot (tftpboot, bootm)
  by adding print lines in the switch driver ar8327.c
  before 'qca,ar8327-initvals' is parsed from DTS and written.
  for example:

    pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-12 18:07:31 +01:00
Michael Pratt
2742705fa5 ath79: split Engenius EPG5000 DTS to common DTSI
Split the DTS to be used with similar boards made by Senao,
dual-band routers with Atheros / Qualcomm ethernet switch.

Set initvals for the switch in each device's DTS.
Set some common calibration nvmem-cells in DTSI.

While at it, fix MTD partition node names.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-12 18:07:31 +01:00
Eneas U de Queiroz
ed81acdcc2
toolchain: wrapper.sh: use --rpath-link
Use --rpath-link option instead of --rpath.  The former is used only at
link-time, while the latter is searched at run-time as well.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2023-02-12 10:55:06 -03:00
Eneas U de Queiroz
9a49e257d6
toolchain: wrapper.sh: fix TOOLCHAIN_SYSROOT path
62c1740676 changed the location of the script from $(TOOLCHAIN_DIR)/usr
to $(TOOLCHAIN_DIR), but the TOOLCHAIN_SYSROOT used in wrapper.sh was
still expecting to find the script under usr/bin.

Fixes: 62c1740676 toolchain: fix the sysroot mess by getting...
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2023-02-12 10:55:05 -03:00
John Audia
3c0676911b kernel: bump 5.15 to 5.15.93
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-11 23:39:30 +01:00
Oleg S
b174de2c5f mediatek: mt7622: fix rootfs/ubi detection for Xiaomi AX6S
By specifying the flag "denx,fit" for partition "kernel", the kernel
try to find rootfs in the same partition during boot. Reality is that
the placement of rootfs is precisely determined by the name of another
partition -"ubi".
It was also found that on some device (for example devices with NAND
chips), the "Denx search engine" manages to find roots at the end of
partition "kernel", but such partition doesn't exist and is empty
there.

Fix this by removing the "denx,fit" flag from partition "kernel". With
this change the original behavior of searchif rootfs in partition "ubi"
is restored.

Signed-off-by: Oleg S <remittor@gmail.com>
2023-02-11 21:42:06 +08:00
Felix Baumann
e8096de9a2
realtek: fix dts whitespace
Remove whitespace from otherwise empty lines

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:52 +01:00
Felix Baumann
d87482a8db
ramips: fix dts whitespace
Replace blanks with tabs
Remove whitespace from otherwise empty lines

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:52 +01:00
Felix Baumann
d88e2aa794
mediatek: fix dts whitespace
Replace blanks with tabs

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:52 +01:00
Felix Baumann
fc4bf73d39
kirkwood: fix dts whitespace
Replace blanks with tabs

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:51 +01:00
Felix Baumann
abdb9f327e
ipq807x: fix dts whitespace
Replace blanks with tabs

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:51 +01:00
Felix Baumann
505cf10e83
ipq806x: fix dts whitespace
Replace blanks with tabs

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:51 +01:00
Felix Baumann
836b994132
bcm63xx: fix dts whitespace
Remove whitespace from otherwise empty lines

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:50 +01:00
Felix Baumann
d0c64ae695
ath79: fix dts whitespace
Replace blanks with tabs
Remove whitespace from otherwise empty lines

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:50 +01:00
Felix Baumann
7fd28f2e3a
ipq40xx: fix dts whitespace
Remove whitespace from otherwise empty lines

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:47 +01:00
Felix Baumann
1c31ca5da9 ipq4019: fix dts white-space
Replace blanks with tabs
Remove whitespace from otherwise empty lines

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-08 02:29:55 +01:00
John Audia
712681458a kernel: bump 5.10 to 5.10.167
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-08 00:22:58 +01:00
John Audia
64cf31f6ff kernel: bump 5.15 to 5.15.92
All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-08 00:21:28 +01:00
Felix Baumann
d53ec2943a lantiq: ar9/vr9: add fritz-tffs package
Add fritz-tffs package to AVM devices
Reorder some devices packages for consistency

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-08 00:19:54 +01:00
Šimon Bořek
628870146d
mpc85xx: p2020: kernel: enable CONFIG_BLK_DEV_NVME
Enables use of NVMe storage devices with appropriate adapter in miniPCIe slots (including for boot)
in Turris 1.x routers and possibly NXP P2020RDB boards
(these are the only currently supported p2020 devices according to docs[^1]).

Proper detection, mountability and readability was proved to be working
on Turris 1.1, OpenWrt 21.02 with similar configuration.

Increases gzip compressed kernel size by approximately 37 KiB (from 3 703 KiB to 3 740 KiB).

Should boot from those devices be possible the driver needs to be built in.
Inclusion as a module would prevent this functionality.

CONFIG_BLK_DEV_NVME=y
Includes NVMe driver in the kernel.[^2]

CONFIG_NVME_CORE=y
Selected by CONFIG_BLK_DEV_NVME.[^3] Not necessarily needed to be enabled explicitly,
but included to match the form of similar functionality implementations
for mvebu, x86_64 and rockchip_armv8 targets.

CONFIG_NVME_MULTIPATH disabled explicitly to prevent using more space than necessary.

[^1]: https://openwrt.org/docs/techref/targets/mpc85xx
[^2]: https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[^3]: https://cateee.net/lkddb/web-lkddb/NVME_CORE.html

Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
2023-02-07 21:24:37 +01:00
Šimon Bořek
acd5aa0bb0
mpc85xx: p2020: kernel: refresh configuration
'make kernel_oldconfig CONFIG_TARGET=subtarget'
applied to current master

Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
2023-02-07 21:24:32 +01:00
Rafał Miłecki
4970dd027b bcm47xx: revert bgmac back to the old limited max frame size
Bumping max frame size has significantly affected network performance
and memory usage. It was done by upstream commit that first appeared in
the 5.7 release.

Allocating 512 (BGMAC_RX_RING_SLOTS) buffers, 10 k each, is clearly a
bad idea on 32 MiB devices. This commit fixes support for Linksys E1000
V2.1 which gives up after allocating ~346 such buffers running 5.15
kernel.

Ref: 230c9da963 ("bcm53xx: revert bgmac back to the old limited max frame size")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-07 18:29:34 +01:00
Filip Matijević
047fb7c76d
ipq806x: add missing enclosing reserved-memory block on C2600/AD7200
Most of the time when booting kernel prints a warning from
mm/page_alloc.c when pstore/ramoops is being initialized and ramoops is
not functional.

Fix this by moving ramopps node into reserved-memory block as described
in kernel documentation.

Fixes: 2964e5024c ("ipq806x: kernel ramoops storage for C2600/AD7200")
Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
2023-02-07 16:27:02 +01:00
Robert Marko
bd9844a6fd ipq807x: refresh kernel config
Refresh the ipq807x kernel config to keep it up to date and in sync with
the generic one.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-02-07 11:22:50 +01:00
Cezary Jackiewicz
cefc543b02
ipq40xx: fix assignment of lan port numbers for Cell C RTL30VW
After switching to DSA, the LAN ports in Cell C RTL30VW have swapped numbers. Assigning the right numbers.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2023-02-06 13:26:58 +01:00
Brian Norris
b5193291bd
ipq806x: onhub: Enable fstools_partname_fallback_scan
When fstools is unable to parse our root=<...> arg correctly, it can
fall back to scanning all block devices for a 'rootfs_data' partition.
This fallback was deemed wrong (or at least, a breaking/incompatible
change) for some targets, so we're forced to opt back into it with
fstools_partname_fallback_scan=1.

Without this, OnHub devices will use a rootfs-appended loop device for
rootfs_data instead of the intended 3rd partition.

While I'm at it, just move all the boot args into the 'cros-vboot'
build rule, instead of using the custom bootargs-append. All cros-vboot
subtargets here are using the same rootwait (to support both eMMC and
USB boot) and root/partition args.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[ drop unrelated comments in commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-02-04 20:16:20 +01:00
Rosen Penev
059263dd6e ipq807x: remove libwolfsslcpu-crypto dependency
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-04 02:35:03 +01:00
Rosen Penev
2630e5063d treewide: replace wpad-basic-wolfssl default
The newly merged mbedtls backend is smaller and has fewer ABI related
issues than the wolfSSL one.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-04 02:35:03 +01:00
Arınç ÜNAL
5155200f97 ramips: mt7621-dts: fix phy-mode of external phy on GB-PC2
The phy-mode property must be defined on the MAC instead of the PHY. Define
phy-mode under gmac1 which the external phy is connected to.

Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-03 14:11:19 +01:00
Tomasz Maciej Nowak
d9a1eee764 x86: add Barracuda Networks F12 interfaces
Match interface numbers with printed numbers on device enclosure and
assign first port as WAN interface.

Notes
Serial console is available through RJ-45 port with Cisco pinout
baud: 19200, parity: none, flow control: none
The device is setup with UEFI. To enter setup hold DEL or ESC key on
boot. Default UEFI Administrator password is: bcndk1
For users using graphics IC it's advisable to disable display with:
i915.disable_display=1
appending to kernel command line inside bootloader, to save about
0.5-0.6W energy on idle.
For users not using graphics IC, disable it in UEFI, this will save about
1.5W energy on idle.
Pins marked CN19 are ATX power On/Off button.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2023-02-03 14:05:37 +01:00
Arınç ÜNAL
c6e412378c ramips: mt7621-dts: fix compatible string for mt7530 on TP-Link EAP615-Wall
The correct compatible string for the multi-chip module MT7530 switch in
MT7621AT, MT7621DAT and MT7621ST SoCs is mediatek,mt7621. Remove the
property on TP-Link EAP615-Wall which will default to the said string.

Fixes: a1b8a4d7b3 ("ramips: support TP-Link EAP615-Wall")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-03 13:49:51 +01:00
Jan Hoffmann
c46584ab30 ramips: use on-flash partition table for Sercomm BZV/CHJ
These devices have a partition table stored in flash, which compensates
for any pre-existing bad blocks by enlarging the respective partition.
This means that the current static partition table is only correct for
devices without any bad blocks.

Typical results of this mismatch are degraded wireless performance and
wrong MAC addresses, when the factory partition is shifted due to a bad
block somewhere before it. If there is a bad block already before the
ubi partition, then OpenWrt may not run at all because the kernel can't
find the rootfs.

Use the on-flash partition table to fix these issues. Replace the two
reserved partitions by the full partition list, as the driver does not
allow merging them.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2023-02-03 13:47:04 +01:00
Tony Butler
8bc72ea7be treewide: strip useless default n Kconfig lines
Kconfig docs say:
> The default value deliberately defaults to 'n' in order to avoid
> bloating the build.

Apply this rule everywhere, to avoid more cloning of bad examples

Signed-off-by: Tony Butler <spudz76@gmail.com>
2023-02-03 12:50:15 +01:00
Mark Ceeha
d4c63c7786 ramips: add support for TP-Link Deco M4R v4
This commit adds support for the V4 hardware revision of the Deco M4R.
V4 is a complete overhaul of the hardware compared to V1 and V2,
and is much more similar to the Archer C6 V3 and C6U V1.

Specifications:

  SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads)
  RAM: Kingston D1216ECMDXGJD (256 MB)
  Wireless 2.4 GHz: MediaTek MT7603EN
  Wireless 5 GHz: MediaTek MT7613BEN
  Flash: 16 MB SPI NOR

Installation:

Flash the *-factory.bin image in the U-Boot recovery webserver.
You can trigger this webserver by holding the reset button until the LED
flashes yellow, or by hooking up to serial pads on the board (clearly
labeled GND, RX and TX) and pressing `x` early in boot.

Once the factory image has been flashed, you can use the regular upgrade
procedure with sysupgrade images for subsequent flashes.

Signed-off-by: Mark Ceeha <hi@shiz.me>
Tested-by: Mark Ceeha <hi@shiz.me>
2023-02-03 12:13:50 +01:00
Hauke Mehrtens
18e6df83bb bcm47xx: Refresh kernel 5.15
This makes the patches and the kernel configuration apply on top of
kernel 5.15.

The following patch was removed because the old IDE subsystem was
removed from upstream kernel:
target/linux/bcm47xx/patches-5.15/610-pci_ide_fix.patch

This was tested successfully on a ASUS WL-500g Premium V1.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-02-03 11:59:07 +01:00
Hauke Mehrtens
30c0ffeccc bcm47xx: Copy kernel from 5.10 to 5.15
Copy patches and configuration from kernel 5.10 to kernel 5.15 files. No
changes were done.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-02-03 11:59:07 +01:00
Rosen Penev
822c554d57 mvebu/uDPU: add quotes to unmount file
This is the last relevant shellcheck warning thrown.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-03 11:34:20 +01:00
Rosen Penev
cb6df29cbd mvebu/uDPU: remove $? usage
shellcheck warns against it with SC2086. It also hides a bug that
shellcheck marks with SC2015. Fixed those with explicit if/else.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-03 11:34:20 +01:00
Rosen Penev
3b80b8e560 mvebu/uDPU: remove echo y
It's a bit of a hack. mkfs.ext4 has an -F parameter that does the same
thing.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-03 11:34:20 +01:00
Rosen Penev
7be11ee35e mvebu/uDPU: simplify grep usage
Instead of using the shell's evaluation, use grep's -q parameter.

Found with shellcheck's SC2143.

Also replaced a head call with grep's -m.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-03 11:34:20 +01:00
John Audia
50324b949b kernel: bump 5.10 to 5.10.166
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-03 09:38:11 +01:00
John Audia
59fe39f6fc kernel: bump 5.15 to 5.15.91
Manually rebased:
  pending-5.15/103-kbuild-export-SUBARCH.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-03 09:34:32 +01:00
Felix Fietkau
521efb62eb mt76: update to the latest version, import WED related mtk_eth_soc patches
6c256218e59e wifi: mt76: dma: use napi_build_skb
679254c50f27 mt7915: add CONFIG_MT76_LEDS to cflags
15b9dd6b1b6a wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work
8e5c21fe7c5c wifi: mt76: mt7915: rework mt7915_mcu_set_thermal_throttling
87cb74fe42d9 wifi: mt76: mt7915: rework mt7915_thermal_temp_store()
c6f24b83eba5 wifi: mt76: mt7915: add error message in mt7915_thermal_set_cur_throttle_state()
99e96b89ee4d wifi: mt76: mt7915: add chip id condition in mt7915_check_eeprom()
833cd420480f wifi: mt76: mt7921: fix channel switch fail in monitor mode
f1f8bae6092d wifi: mt76: mt7921: add ack signal support
f47087a6dd62 wifi: mt76: mt7996: fix chainmask calculation in mt7996_set_antenna()
2f3b0acc1588 wifi: mt76: mt7996: update register for CFEND_RATE
7e9540dcbd70 wifi: mt76: mt7996: do not hardcode vht beamform cap
a37e427d0959 wifi: mt76: connac: fix POWER_CTRL command name typo
98aa346042bd wifi: mt76: mt7915: remove BW160 and BW80+80 support
94fed6a43541 wifi: mt76: mt7921: fix invalid remain_on_channel duration
3c162384d80a wifi: mt76: introduce mt76_queue_is_wed_rx utility routine
a409a9454587 wifi: mt76: mt7915: fix memory leak in mt7915_mcu_exit
8b27ecd3a684 wifi: mt76: mt7996: fix memory leak in mt7996_mcu_exit
683760461dd0 wifi: mt76: dma: free rx_head in mt76_dma_rx_cleanup
0c750cf08f85 wifi: mt76: dma: fix memory leak running mt76_dma_tx_cleanup
5de9ae29bea2 wifi: mt76: mt7915: avoid mcu_restart function pointer
dad96dd3e62d wifi: mt76: mt7603: avoid mcu_restart function pointer
19d36dd9c8ea wifi: mt76: mt7615: avoid mcu_restart function pointer
6fe2c2383d3d wifi: mt76: mt7921: avoid mcu_restart function pointer
9df89143bf71 wifi: mt76: mt7915: get rid of wed rx_buf_ring page_frag_cache
8d51d11760cb wifi: mt76: fix switch default case in mt7996_reverse_frag0_hdr_trans
0d8057dbd51c wifi: mt76: mt7921u: add support for Comfast CF-952AX
ddbf4e933d54 wifi: mt76: mt7915: set sku initial value to zero
06a8904e954e wifi: mt76: mt7915: wed: enable red per-band token drop
724a337caef9 wifi: mt76: mt7915: fix WED TxS reporting
747ca943a5bb wifi: mt76: add flexible polling wait-interval support
133d7859977a wifi: mt76: mt7921: reduce polling time in pmctrl
5fe319a0550e wifi: mt76: add memory barrier to SDIO queue kick
822f060b9d19 wifi: mt76: mt7921: fix rx filter incorrect by drv/fw inconsistent
c6794954a723 wifi: mt76: mt7915: fix memory leak in mt7915_mmio_wed_init_rx_buf
9686cd7cc65c wifi: mt76: switch to page_pool allocator
04da4eaa8235 wifi: mt76: enable page_pool stats
1af4a911ebcb wifi: mt76: mt7915: release rxwi in mt7915_wed_release_rx_buf
e8c10835cf06 wifi: mt76: fix compile error without CONFIG_PAGE_POOL_STATS
0cf0ede7cc42 net: ethernet: mtk_wed: add reset to rx_ring_setup callback
715b3ed9708a net: ethernet: mtk_wed: add reset to tx_ring_setup callback
9107381d0ff3 wifi: mt76: mt7921: fix error code of return in mt7921_acpi_read
36d2a5bf7802 wifi: mt76: mt7996: rely on mt76_connac2_mac_tx_rate_val
c67f57d2cda2 wifi: mt76: dma: add reset to mt76_dma_wed_setup signature
3dace36e2941 wifi: mt76: dma: reset wed queues in mt76_dma_rx_reset
4b229d2da562 wifi: mt76: mt7915: add mt7915 wed reset callbacks
f83958376085 wifi: mt76: mt7915: complete wed reset support
321edbb414dc wifi: mt76: mt7996: rely on mt76_connac_txp_common structure
bdb7dc38a6d1 wifi: mt76: mt7996: rely on mt76_connac_txp_skb_unmap
8688756305c6 wifi: mt76: mt7996: rely on mt76_connac_tx_complete_skb
fbf986dbd4c0 wifi: mt76: mt7996: rely on mt76_connac2_mac_decode_he_radiotap
adc556cbce37 wifi: mt76: mt7996: avoid mcu_restart function pointer
5eb4e2303be4 wifi: mt76: remove __mt76_mcu_restart macro
e7a61c5f70f5 wifi: mt76: add EHT phy type
b375845abc10 wifi: mt76: connac: add CMD_CBW_320MHZ
68b17a243332 wifi: mt76: connac: add helpers for EHT capability
02ec1f61b3a2 wifi: mt76: connac: add cmd id related to EHT support
9209294cd81b wifi: mt76: increase wcid size to 1088
5e85136c9b2f wifi: mt76: add EHT rate stats for ethtool
a171f672fdeb wifi: mt76: mt7996: add variants support
eda8fd62c105 wifi: mt76: mt7996: add helpers for wtbl and interface limit
4a5a9f4cdc3b wifi: mt76: mt7996: rework capability init
06b73c155680 wifi: mt76: mt7996: add EHT capability init
ae71a1b8294f wifi: mt76: mt7996: add support for EHT rate report
65bdfae2991d wifi: mt76: mt7996: enable EHT support in firmware
b2360d59747c wifi: mt76: mt7996: add EHT beamforming support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-02 11:16:49 +01:00
Hannu Nyman
91add68e50
ipq807x: Enable CPU frequency scaling stats
Enable the CPU frequency scaling statistics in kernel config.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2023-01-31 16:33:21 +01:00
INAGAKI Hiroshi
3cfa465387
realtek: use generic earlycon setup on 5.15
Use generic earlycon on Linux Kernel instead of initialization in platform
setup.
And also, drop bootargs with console= parameter from I-O DATA BSH-G24MB. It
uses 115200bps as baud-rate, the same as default in rtl838x.dtsi.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-30 14:30:41 +01:00
Zoltan HERPAI
d649a8dcef mxs: switch default kernel to 5.15
The testing kernel has been available since Mar/2022, let's switch
to it by default.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-01-30 11:13:14 +01:00
Robert Marko
c2903ebadc ath25: mark as source-only
ath25 seems to be a target with low number of users according to download
statistics, most of which are for older releases anyway.
Users that we managed to find are currently building images downstream as
due to low amount of RAM (32MB) default config will not work.

Target also suffers from inability for the 5.15 kernel bump to be tested
which is a requirment for the next release.

So, for those reasons, lets mark it as source-only so that Buildbots dont
use the resources for building the images for this target anymore.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-30 18:01:14 +08:00
Chuanhong Guo
0c64c5f520 zynq: remove kconfig for 5.10
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2023-01-30 18:01:14 +08:00
Nick Hainke
459d40811e zynq: switch default kernel to 5.15
The default kernel should be switched to 5.15 in order to enable testing
by a broader audience.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-30 18:01:14 +08:00
Sander Vanheule
a336b6c7cf realtek: remove KERNEL_PATCHVER overrides
On the realtek target, the subtarget makefiles include a KERNEL_PATCHVER
setting, shadowing KERNEL_PATCHVER from target/linux/realtek/Makefile.
This makes the realtek target an exception in this regard, and makes
switching kernel version a bit bothersome. Remove the overrides so all
subtargets use the same kernel version.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-29 16:29:42 +01:00
Felix Fietkau
d02d455678 kernel: make it possible for packages to select page pool support
Will be used by the next mt76 update

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-29 10:08:21 +01:00
Felix Fietkau
2770cbe63f kernel: add fix for a page pool related crash on GRO
Needed for upcoming mt76 page pool support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-29 10:08:21 +01:00
Felix Fietkau
638283d481 kernel: backport page pool fragment support from v5.15
Required for an upcoming mt76 update

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-29 10:08:21 +01:00
Chen Minqiang
016a7bd558 mediatek: fix wrong return code in platform_check_image()
Ensure that the platform_check_image() function returns an error code.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2023-01-29 01:02:45 +00:00
Dmitry Sokolov
39e4f03fd3 ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2
Device is the same as Xiaomi Mi Router 4A Gigabit, except of:
- 5G WiFi is MT7663
- addresses of leds, wifi and eth ports are slightly changed

Specs:
  SoC:  MT7621
  CPU:  2 x 880 MHz
  ROM:  16 MB
  RAM:  128 MB
  WLAN: MT7603, MT7663

MAC addresses:
  WAN     ****  factory 0xe006 (label)
  LAN     *:f7  factory 0xe000
  2.4 GHz *:f8  factory 0x0000+0x4 (mtd-eeprom+0x4)
  5 GHz   *:f9  factory 0x8000+0x4 (mtd-eeprom+0x4)

Installation:

Factory firmware is based on a custom OpenWrt 17.x.
Installation is the same as for Xiaomi Mi Router 4A Gigabit.

Probably the easiest way to install is to use the script from
this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155

In a more advanced case, you can do everything yourself:
- gain access to the device through one of the exploits described
  in the link above
- upload sysupgrade image to /tmp
- overwrite stock firmware:
  # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1

Recovery:

Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit.
Possible options can be found here:
https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition

One of the ways is to use another router with OpenWrt:
- connect both routers by their LAN ports
- download stock firmware from [1]
- place it inside /tmp/test.bin on the main router
- configure PXE/TFTP on the main router
- power off 4Av2, hold Reset button, power on
- as soon as image download via TFTP starts, Reset can be released
- blinking blue wan LED will indicate the end of the flashing process,
  now router can be rebooted
[1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin

Signed-off-by: Dmitry Sokolov <e323w@proton.me>
2023-01-28 22:11:44 +01:00
Maxim Anisimov
3690c4a092 ramips: improve support for Zyxel Keenetic Extra II
- drop unneeded default-state for led_power
- concat firmware partitions to extend available free space
- increase spi flash frequency to 32 Mhz (value from stock firmware bootlog)
- drop broken-flash-reset because of onboard flash chip W25Q256FV has reset support
- add compatible for pcie wifi according to kernel documetation
- switch to wan mac address with offset 0x28 in rf-eeprom

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-28 21:45:34 +01:00
Maxim Anisimov
2fe29794b1 ramips: use hex value in zyimage command for Keenetic KN-3010
This is cosmetic change. The hex value is related to the device
model and more human friendly.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-28 21:40:37 +01:00
Tom Herbers
67f283be44 ath79: add LTE packages for GL-XE300
Add LTE packages required for operating the LTE modems shipped with
the GL-XE300.

Example configuration for an unauthenticated dual-stack APN:

network.wwan0=interface
network.wwan0.proto='qmi'
network.wwan0.device='/dev/cdc-wdm0'
network.wwan0.apn='internet'
network.wwan0.auth='none'
network.wwan0.delay='10'
network.wwan0.pdptype='IPV4V6'

Signed-off-by: Tom Herbers <mail@tomherbers.de>
2023-01-28 21:38:51 +01:00
Shiji Yang
c7059c56a8 ath79: improve support for Letv LBA-047-CH
1. Convert wireless calibration data to NVMEM.
2. Enable control green status LED and change default LED behaviors.
   The three LEDs of LBA-047-CH are in the same position, and the green
   LED will be completely covered by the other two LEDs. So don's use
   green LED as WAN indicator to ensure that only one LED is on at a time.
   LED     Factory          OpenWrt
   blue    internet fail    failsafe && upgrade
   green   internet okay    run
   red     boot             boot
3. Reduce the SPI clock to 30 MHz because the ath79 target does not
   support 50 MHz SPI operation well. Keep the fast-read support to
   ensure the spi-mem feature (b3f9842330) is enabled.
4. Remove unused package "uboot-envtools".
5. Split the factory image into two parts: rootfs and kernel.
   This change can reduce the factory image size and allow users to
   upgrade the OpenWrt kernel loader uImage (OKLI) independently.

   The new installation method: First, rename "squashfs-kernel.bin" to
   "openwrt-ar71xx-generic-ap147-16M-kernel.bin" and rename "rootfs.bin"
   to "openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin". Then we
   can press reset button for about 5 seconds to enter tftp download mode.
   Finally, set IP address to 192.168.67.100 and upload the above two
   parts via tftp server.

Tested on Letv LBA-047-CH

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-28 21:37:14 +01:00
Edward Chow
2a20dc717a ath79: calibrate dlink dir-825 c1 and dir-835 a1 with nvmem
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

Currently, "mac-address-ascii" cells only works for ethernet and wmac devices,
so PCI ath9k device uses the old method to calibrate.

Signed-off-by: Edward Chow <equu@openmail.cc>
2023-01-28 21:28:25 +01:00
Tony Butler
a7f3a51982 kernel: add kmod-lib-842
"842" is a compression scheme and this is the software implementation
which is too slow to really use beyond a proof of concept.  It can be
selected in ZRAM, ZSWAP, or `fs/pstore`, and is here for completeness.
In general you need a Power8 or better with 842-in-hardware for it to
be fast, but other 842-accelerators are emerging.

Signed-off-by: Tony Butler <spudz76@gmail.com>
2023-01-28 21:19:17 +01:00
Tom Herbers
f83f5f8452 ath79: add label-mac-device for GL-XE300
This adds an label-mac-device alias which refrences the mac which is
printed on the Label of the device.

Signed-off-by: Tom Herbers <mail@tomherbers.de>
2023-01-28 21:11:17 +01:00
Daniel Groth
a911f63df9 realtek: dgs-1210-10mp: update sfp phy-handle
Adjust the wrong phy-handle definitions for the sfp ports so that they
match the correct switch ports.

Fixes: 89eb8b50d1 ("realtek: dgs-1210-10mp: add full sfp description")
Signed-off-by: Daniel Groth <flygarn12@gmail.com>
2023-01-28 21:01:29 +01:00
Michael Pratt
52992efc34 ath79: add support for Senao Engenius EWS660AP
FCC ID: A8J-EWS660AP

Engenius EWS660AP is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9558 SOC		2.4 GHz, 3x3
  - QCA9880 WLAN	mini PCIe card, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - AR8033 PHY		SGMII GbE with PoE+ OUT
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM
  - UART at J1		populated, RX grounded
  - 6 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)

**MAC addresses:**

  Base MAC addressed labeled as "MAC"
  Only one Vendor MAC address in flash

  eth0 *:d4 MAC art 0x0
  eth1 *:d5 --- art 0x0 +1
  phy1 *:d6 --- art 0x0 +2
  phy0 *:d7 --- art 0x0 +3

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs.bin to '0101A8C0.img'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

**Format of OEM firmware image:**

  The OEM software of EWS660AP is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-ews660ap-uImage-lzma.bin
    openwrt-ar71xx-generic-ews660ap-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Tested-by: Niklas Arnitz <openwrt@arnitz.email>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-01-28 20:34:00 +01:00
Michael Pratt
290a6527be ath79: add pcie1 wifi device to Senao qca955x AP DTSI
Each individual device DTS now enables either pcie0 or pcie1.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-01-28 20:34:00 +01:00
Hauke Mehrtens
5d227b1603 pistachio: Cleanup kernel configuration
This removes some kernel configuration options which are not needed.
This brings the target closer to the OpenWrt standard configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-28 19:58:20 +01:00
Hauke Mehrtens
3ba8dd0731 realtek: Refresh kernel patches
Make the patches apply cleanly again.

Fixes: 4db8598e42 ("realtek: Do not set KERNEL_ENTRY just to avoid NO_EXCEPT_FILL")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-28 19:49:51 +01:00
Olliver Schinagl
afb5d9e9d5 realtek: timer: Fix cosmetic whitespace in comments
Comments are a bit weird in the timer driver, lets fix those.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-28 17:31:12 +01:00
Olliver Schinagl
f6ba61b929 realtek: timer: Remove CEVT_RTL9300 completely
As the timer has been fixed now, we can drop the CEVT_RTL9300 timer all
together.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-28 17:31:12 +01:00
Olliver Schinagl
68e28cdc47 realtek: timer: Activate for RTL930x devices
Use the new timer driver for the RTL930x devices.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[remove old clock provider, select MIPS_EXTERNAL_TIMER and refresh
kernel config]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-28 17:30:26 +01:00
Sander Vanheule
38cba61bff
realtek: timer: Register enabled scheduler clock
Before calling sched_clock_register(), the timer used to drive the
scheduling clock should already be enabled. Otherwise the kernel log
will show strange time jumps during, and the watchdog might not be
pinged in a timely fashion, resulting in reboots.

[    0.160281] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[   78.104319] clocksource: Switched to clocksource realtek_otto_timer

Fixes: 3cc8011171 ("realtek: resurrect timer driver")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-28 15:23:03 +01:00
Zoltan HERPAI
6e428a8490 mxs: fix SD-card image generation for OLinuXino boards
Fixes: mxs: add generic subtarget (64ef920)

Adding the generic target caused the TARGET_BOOTFS_PARTSIZE to stay
hidden for these boards, crashing the FAT filesystem creation.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-01-27 23:19:38 +01:00
Olliver Schinagl
7f5edeb8bd realtek: eth: Fix missing end of comment marker
Because this comment is followed by another comment, nothing luckily
breaks, so only a cosmetic change.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-27 22:03:17 +01:00
Shiji Yang
cfb296b79a ath79: add support for D-Link DIR-629 A1
Specifications:
  SOC:      QCA9588 CPU 720 MHz AHB 200 MHz
  Switch:   AR8236
  RAM:      64 MiB DDR2-600
  Flash:    8 MiB
  WLAN:     Wi-Fi4 2.4 GHz 3*3
  LAN:      LAN ports *4
  WAN:      WAN port *1
  Buttons:  reset *1 + wps *1
  LEDs: ethernet *5, power, wlan, wps

MAC Address:
  use      address               source
  label    70:62:b8:xx:xx:96     lan && wlan
  lan      70:62:b8:xx:xx:96     mfcdata@0x35
  wan      70:62:b8:xx:xx:97     mfcdata@0x6a
  wlan     70:62:b8:xx:xx:96     mfcdata@0x51

Install via Web UI:
  Apply factory image in the stock firmware's Web UI.

Install via Emergency Room Mode:
  DIR-629 A1 will enter recovery mode when the system fails to boot or
  press reset button for about 10 seconds.

  First, set IP address to 192.168.0.1 and server IP to 192.168.0.10.
  Then we can open http://192.168.0.1 in the web browser to upload
  OpenWrt factory image or stock firmware. Some modern browsers may
  need to turn on compatibility mode.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-26 00:32:36 +01:00
John Audia
4e9365a654 kernel: bump 5.15 to 5.15.90
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-26 00:16:00 +01:00
Sander Vanheule
8f47b87b0c realtek: rtl931x: drop LINKER_LOAD_ADDRESS bypass
RTL931x kernel builds were patched to bypass the LINKER_LOAD_ADDRESS
parameter, and hardcode it to 0x80220000. This doesn't make much sense,
since value of LINKER_LOAD_ADDRESS, load-ld, only appears to be a copy
of load-y, adjusted to the linker's taste.

Dropping the hacks for bypassing LINKER_LOAD_ADDRESS results in a kernel
that actually starts booting on an RTL9313 (Netgear MS510TXM), but
currently still hangs when the kernel switches timers.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-25 22:39:35 +01:00
Wenli Looi
7396263680 ath79: convert Netgear EX7300 caldata to nvmem
Transition to specify caldata in the DTS.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-01-25 00:42:52 +01:00
Wenli Looi
f0eb73a888 ath79: consolidate Netgear EX7300 series images
This change consolidates Netgear EX7300 series devices into two images
corresponding to devices that share the same manufacturer firmware
image. Similar to the manufacturer firmware, the actual device model is
detected at runtime. The logic is taken from the netgear GPL dumps in a
file called generate_board_conf.sh.

Hardware details for EX7300 v2 variants
---------------------------------------
SoC: QCN5502
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 1 gigabit port
Wireless 2.4GHz (currently unsupported due to lack of ath9k support):
- EX6250 / EX6400 v2 / EX6410 / EX6420: QCN5502 3x3
- EX7300 v2 / EX7320: QCN5502 4x4
Wireless 5GHz:
- EX6250: QCA9986 3x3 (detected by ath10k as QCA9984 3x3)
- EX6400 v2 / EX6410 / EX6420 / EX7300 v2 / EX7320: QCA9984 4x4

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-01-25 00:42:52 +01:00
John Audia
257e9fc57c kernel: bump 5.10 to 5.10.165
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-24 23:08:43 +01:00
John Audia
9c3954bc46 kernel: bump 5.10 to 5.10.164
All patches automatically rebased

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-24 23:08:43 +01:00
Lorenz Brun
bec9e79a99 realtek: dsa: support active-high LEDs
The TP-LINK TL-ST1008F has active-high LEDs, so we need a device tree
property to express this.

Signed-off-by: Lorenz Brun <lorenz@brun.one>
[Tidy up code, restrict changes to 5.15]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-24 21:55:44 +01:00
Sander Vanheule
d84dc5d4d7 realtek: rtl931x: drop CONFIG_NO_EXCEPT_FILL hack
On RTL931x builds, CONFIG_RTL931X was used as a stand-in for
CONFIG_NO_EXCEPT_FILL.  Now that the latter is always selected for
devices in the realtek target, this hack can be removed. Resulting
device images are binary identical.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2023-01-24 21:35:00 +01:00
Olliver Schinagl
1bf39d91d5 realtek: Refresh kernel config with no_except_fill
Update the config files with the previous commit.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-24 21:00:19 +01:00
Olliver Schinagl
4db8598e42 realtek: Do not set KERNEL_ENTRY just to avoid NO_EXCEPT_FILL
It seems like we are offsetting the KERNEL_ENTRY to +0x400, which is
also accomplished by the NO_EXCEPT_FILL configuration option.

Since this is the default for MIPS_GENERIC_KERNEL, lets push a little
bit closer to that one by doing the same thing.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-24 21:00:19 +01:00
Nick Hainke
ac21dff5b6 pistachio: switch to 5.15 by default
It appears that only a few users are using the pistachio SoC. The most
active user of the target has already approved the testing kernel and
so it is very unlikely bugs will be reported in the near future.
Therefore, the target should be directly bumped to 5.15.

Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-24 00:30:47 +01:00
Nick Hainke
496d32cb78 pistachio: add 5.15 testing kernel
Manually refreshed:
- 903-MIPS-DTS-img-marduk-Add-NXP-SC16IS752IPW.patch
- 905-MIPS-DTS-img-marduk-Add-led-aliases.patch (led node was renamed to led-1)

Automatically refreshed:
- 109-MIPS-DTS-img-marduk-switch-mmc-to-1-bit-mode.patch
- 401-mtd-nor-support-mtd-name-from-device-tree.patch
- 901-MIPS-DTS-img-marduk-Add-SPI-NAND-flash.patch
- 902-MIPS-DTS-img-marduk-Add-Cascoda-CA8210-6LoWPAN.patch
- 904-MIPS-DTS-img-marduk-Add-partition-name.patch

Enable testing kernel.

Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-24 00:30:47 +01:00
Nick Hainke
94059ce864 pistachio: 5:15: copy config and patch from 5.10
Copy config and patch from kernel 5.10 to kernel 5.15.

Signed-off-by: Nick Hainke <vincent@systemli.org>
[Updated the copy]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-24 00:30:19 +01:00
Robert Marko
e3082dc555
generic: backport fix for #nvmem-cell-cells false warning
Recent backport of NVMEM layout support as well as acommpanying OF changes
introduced a false #nvmem-cell-cells warning as #nvmem-cell-cells are
fully optional.

So, backport an upstream fix for this.

Fixes: 11759a5bf3 ("kernel: backport of changes & helpers")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-23 19:08:01 +01:00
Nikolay Martynov
62dbcb8305 ramips: Fix root volume for tplink-er605-v2
This device has two sets of volumes: main ones (`kernel`, `rootfs`, etc) and
'backup' (`kernel.b`, `rootfs.b`, etc). Bootloader tries to determine which set of
volumes to use by looking at contens of `extra-para` and `extra-para.b` volumes.
These volumes contain JSON that looks like this:

```
{
	"dbootFlag": "1",
	"integerFlag": "1",
	"fwFlag": "GOOD",
	"score":1
}
```

It looks like the bootloader looks for `"fwFlag": "GOOD"` (as opposed to `BAD`)
then it compares `score` field - whichever 'good' volume has bigger score wins.
This determines which set of volumes to use to boot.

So for example if `extra-para` is good and has bigger score then `kernel`,
`rootfs`, etc volumes are used. This means bootloader needs to explain to the
kernel which volume to use for the rootfs. After looking at bootloader code with
disassembler I think it contains a bug. Relevant part of code looks something
like this:

```
  if (image_id == 0) {
    rootfs_volume_id = 8;
    rootfs_volume_name = "rootfs";
  }
  else {
    rootfs_volume_id = 0xf;
    rootfs_volume_name = "rootfs.b";
  }
  sprintf(
    &buffer,
    0x800,
    "console=ttyS0,115200 noinitrd ubi.mtd=3,2048 ubi.block=0,%s
    root=/dev/ubiblock0_%d DKMGT_IMAGE_ID=%d DKMGT_IMAGE_TYPE=ubi",
    rootfs_volume_name,
    rootfs_volume_id,
    image_id
    );
```

Where `image_id == 0` if 'normal' (not '*.b' set of volumes is used).
However from device dumps we know that from the factory `rootfs.b` has id 8 and
`rootfs` has id 15.

So from above we can see that ids and names of rootfs volumes do not match. More
over - they are hardcoded in the bootloader.

Both things are problematic for OpwnWRT which completely removes volumes on
update meaning that volume ids may actually change.

So instead of relying on bootloader to provide the kernel with root device this
patch forces kernel to determine root automatically - and it defaults to
`rootfs` volume which is correct for our purposes.

Overall this makes image boot fine from flash after sysupgrade from inirams.
assuming `extra-para*` volumes make bootloader use non-'*.b' set of volumes.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
2023-01-22 14:37:47 +01:00
Alexey Smirnov
f86658e269 omap: refresh config
Refresh target config by running:
make kernel_nconfig CONFIG_TARGET=target

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2023-01-22 02:08:28 +01:00
Alexey Smirnov
c2f0419a12 omap: enable ARM Accelerated Cryptographic Algorithms
This selects cryptographic algorithms implemented
using ARM specific CPU features.

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2023-01-22 02:08:28 +01:00
Alexey Smirnov
8a3a4c84d7 omap: enable cpuidle driver
This enables generic cpuidle driver for ARM.

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2023-01-22 02:08:28 +01:00
John Audia
6a3816efb7 kernel: bump 5.15 to 5.15.89
Removed upstreamed:
  ipq806x/patches-5.15/007-v6.3-ASoC-qcom-lpass-cpu-Fix-fallback-SD-line-index-handl.patch[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.89&id=d4fa65960a9d0cb87a1102d47145675ceed7a4e6

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-22 01:41:10 +01:00
INAGAKI Hiroshi
614bba0958 realtek: use irq_force_affinity on otto timer instead
After commit e0d2c59ee995 ("genirq: Always limit the affinity to online
CPUs", 5.10) on Linux, the cpumask passed to irq_set_affinity of irqchip
driver is limited to online CPUs. When irq_do_set_affinity called from
otto timer driver with only one secondary CPU, that CPU is not marked as
online yet, filtered out by cpu_online_mask and fall to error path.
Then, fail to set affinity for that CPU and it leads to instability of
timer on secondary CPU(s).

At least, RTL839x system will be affected.

log:

[   37.560020] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[   37.638025] rcu:     1-...!: (0 ticks this GP) idle=6ac/0/0x0 softirq=0/0 fqs=1  (false positive?)
[   37.752683]  (detected by 0, t=6002 jiffies, g=-1179, q=26293)
[   37.829510] Sending NMI from CPU 0 to CPUs 1:
[   37.886857] NMI backtrace for cpu 1 skipped: idling at r4k_wait_irqoff+0x1c/0x24
[   37.984801] rcu: rcu_sched kthread timer wakeup didn't happen for 5999 jiffies! g-1179 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402
[   38.132743] rcu:     Possible timer handling issue on cpu=1 timer-softirq=0
[   38.221033] rcu: rcu_sched kthread starved for 6000 jiffies! g-1179 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=1
[   38.356336] rcu:     Unless rcu_sched kthread gets sufficient CPU time, OOM is now expected behavior.
[   38.474440] rcu: RCU grace-period kthread stack dump:
...

Replace to irq_force_affinity from irq_set_affinity and ignore
cpu_online_mask to fix the issue.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-21 19:58:24 +01:00
Chuanhong Guo
f183ce35b8
kernel: mtk-bmt: fix usage of _oob_read
_oob_read returns number of bitflips on success while
bbt_nand_read should return 0.

Fixes: 2d49e49b18 ("mediatek: bmt: use generic mtd api")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2023-01-21 10:54:23 +08:00
Brian Norris
ef649b0b14
ipq806x: Initial TP-Link and ASUS OnHub support
TP-Link and ASUS OnHub devices are very similar, sharing many of the
same characteristics and much of their Device Tree. They both run a
version of ChromeOS for their factory firmware, and so installation
instructions look very similar to Google Wifi [1].

Things I've tested, and are working:

 * Ethernet
 * WiFi (2.4 and 5 GHz)
 * LEDs
 * USB
 * eMMC
 * Serial console (if you wire it up yourself)
 * 2x CPU
 * Speaker

== Installation instructions summary ==

1. Flash *-factory.bin to a USB drive (e.g., with `dd`)
2. Insert USB drive, to boot OpenWrt from USB
3. Copy the same *-factory.bin over to device, and flash it to eMMC to
   make OpenWrt permanent

== Developer mode, booting from USB (Step 2) ==

To enter Developer Mode and boot OpenWrt from a USB stick:

1. Unplug power
2. Gain access to the "developer switch" through the bottom of the
   device
3. Hold down the "reset switch" (near the USB port / power plug)
4. Plug power back in
5. The LED on the device should turn white, then blink orange, then
   red. Release the reset switch.
6. Insert USB drive with OpenWrt factory.bin
7. Press the hidden developer switch under the device to boot to USB;
   you should see some activity lights (if you have any) on your USB
   drive
8. Depending on your configuration, the router's LED(s) should come on.
   You're now running OpenWrt off a USB stick.

These instructions are derived from:

https://www.exploitee.rs/index.php/Rooting_The_Google_OnHub#Enabling_%22Developer_Mode%22_on_the_OnHub
https://www.exploitee.rs/index.php/Asus_OnHub#Enabling_%22Developer_Mode%22_on_the_OnHub

~~Finding the developer switch:~~ for TP-Link, the developer switch is
on the bottom of the device, underneath some of the rubber padding and a
screw. For ASUS, remove the entire base, via 4 screws under the rubber
feet. See the Exploitee instructions for more info and photos.

== Making OpenWrt permanent (on eMMC) (Step 3) ==

Once you're running OpenWrt via USB:

1. Connect Ethernet to the LAN port; router's LAN address should be at
   192.168.1.1
2. Connect another system to the router's LAN, and copy the factory.bin
   image over, via SCP and SSH:

     scp -O openwrt-ipq806x-chromium-tplink_onhub-squashfs-factory.bin root@192.168.1.1:
     ssh root@192.168.1.1 -C "dd if=/dev/zero bs=512 seek=7552991 of=/dev/mmcblk0 count=33 && \
     dd if=/root/openwrt-ipq806x-chromium-tplink_onhub-squashfs-factory.bin of=/dev/mmcblk0"
3. Reboot and remove the USB drive.

== Developer mode beep ==

Note that every time you boot the OnHub in developer mode, the device
will play a loud "beep" after a few seconds. This is described in the
Chromium docs [2], and is intended to make it clear that the device is
not running Google software. It is nontrivial to completely disable this
beep, although it's possible to "acknowledge" developer mode (and skip
the beep) by using a USB keyboard to press CTRL+D every time you boot.

[1] https://openwrt.org/toh/google/wifi
[2] https://chromium.googlesource.com/chromiumos/docs/+/HEAD/developer_mode.md

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:25 +01:00
Brian Norris
69d1b289b0
ipq806x: Add kmod-sound-soc-ipq8064-storm
For IPQ8064 systems based off the "Google Storm" reference platform,
such as the TP-Link OnHub.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:25 +01:00
Brian Norris
c20915e841
ipq806x: ASoC: qcom: lpass-cpu: Fix fallback SD line index handling
This fixes device tree registration for 'qcom,lpass-cpu' as used by
qcom-ipq8064 SoCs, and allows speaker audio to function.

This patch has been submitted (and merged, for -next; likely v6.3)
upstream.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:24 +01:00
Brian Norris
108ed0e1c7
ipq806x: config-5.15: Normalize
Refresh target config with `make kernel_menuconfig`, then save the
result. This drops missing symbols or otherwise accounts for defaults.
It should not change any functionality.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:24 +01:00
Brian Norris
84ee3436a4
ipq806x: Point to externally compiled dtbs in recipes
Similar to commit 4d8b42d8a7 ("ipq40xx: point to externally compiled
dtbs in recipes").

Currently, we patch our DTS files into the kernel source tree, so the
kernel build process will produce DTBs for us. The kernel-to-DTS
dependency can cause buildroot to perform excessive rebuilds of the
kernel though, which slows down device development iteration.

Buildroot also compiles DTBs on its own, to
$(KDIR)/image-$(DEVICE_DTS).dtb. With small adjustments, we can leverage
this, and stop patching DTS files into the kernel Makefile at the same
time.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:24 +01:00
Josef Schlehofer
6475d030b9 mvebu: cortexa9: use renamed U-boot binaries
Due to upstream change in U-boot the binaries were renamed [1].

[1] 87ac4b4b4c

Fixes: 2f83369e3e ("uboot-mvebu: update to version 2023.01")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2023-01-20 21:10:37 +01:00
André Valentin
5dee596501
ipq807x: Add ZyXEL NBG7815
ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1 GB 2x Nanya NT5CC256M16ER-EK
* Storage:
        * 8MB serial flash Winbond W25Q64DW
        * 4GB eMMC flash Kingston EMMC04G-M627
* Ethernet:
        * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port
        * 1x2.5G RJ45 port (QCA8081) with 1x status LED
        * 1x10G RJ45 port (AQR113C) with 1x status LED
* Switch: Qualcomm Atheros QCA8075
* WLAN:
        * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
        * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
* Bluetooth CSR8811 using HSUART, currently unsupported
* USB: 1x USB3.0 Type-A port
* LED-s currently not supported:
        * White
        * Dark Blu
        * Amber
        * Purple
        * Purple and dark blue
        * Red
* Buttons:
        * 1x Soft reset
* Power: 12V DC Jack

Installation instructions:
* Disconnect WAN
* Reset device to factory defaults by pushing reset button 15 sec,
  LEDs should lit orange color.
* After 5-10 minutes, when the LEDs turn constant dark blue,
  put your LAN cable and connect at address 192.168.123.1 by telnet on port 23
* Login with
  NBG7815 login: root
  password: nbg7815@2019
* cd /tmp/ApplicationData
* wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://...
* wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh
* run flash_to_openwrt.sh
If you can't use wget, you can transfer the files via nc.
See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details.

Bluetooth usage:
* you need at least package bluez-utils, recommended bluez-daemon
* run following commands to enable and start
  hciattach  /dev/ttyMSM1 bcsp
  hciconfig hci0 up

Many thanks to itorK for his work on this device:
https://github.com/itorK/openwrt/tree/nbg7815

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-19 13:26:15 +01:00
André Valentin
952c738c0f
ipq807x: add nvmem uboot-env support
Enabling kernel symbol CONFIG_NVMEM_U_BOOT_ENV allows to use u-boot
environement variable ethaddr with nvmen. That way it is possible to assign
the MAC address to the ethernet device driver.

Example of usage in dts:
....
	partition@600000 {
			compatible = "u-boot,env";
			label = "0:appsblenv";
			reg = <0x600000 0x10000>;

			macaddr_lan: ethaddr {
			};
	};
....
&dp5 {
	status = "okay";
	phy-handle = <&qca8081>;
	label = "wan";
	nvmem-cells = <&macaddr_lan>;
	nvmem-cell-names = "mac-address-ascii";
	mac-address-increment = <1>;
};

This is needed for Zyxel NBG7815.

Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-19 13:26:15 +01:00
James Andrewartha
7c04e80f87 ipq40xx: convert Extreme AP3915i to DSA
Convert and re-enabled Extreme AP3915i to DSA.

Signed-off-by: James Andrewartha <trs80@ucc.asn.au>
2023-01-17 23:45:44 +01:00
Martin Schiller
539b52068a ipq40xx: add DSL support for FritzBox 7530
Set up MAC, LED, settings and default packages for DSL usage, similar
to the lantiq target.

Due to licensing uncertainty, we do not include the firmware files for the
DSL drivers. To have a working DSL setup, follow the instructions below.

Download the firmware files locally:

  mkdir -p files/lib/firmware/09a9
  wget -P files/lib/firmware/09a9 https://gitlab.com/prpl-foundation/intel/vrx518_aca_fw/-/raw/ugw-8.5.2/platform/xrx500/aca_fw.bin
  wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/vrx518_ppe_fw/-/raw/ugw_8.5.2.10/platform/xrx500/ppe_fw.bin
  wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/dsl_vr11_firmware_xdsl/-/raw/ugw-8.5.2/xcpe_8D1507_8D0901.bin
  ln -s xcpe_8D1507_8D0901.bin files/lib/firmware/vdsl.bin

For people building their own images:

Run the above commands in the root of your local OpenWrt clone,
and the firmware files will be part of the resulting images.

For people downloading images:

Copy the firmware files onto the router once it's booted up:
  scp -O -r files/lib/firmware root@fritz:/lib
Reboot the device afterwards.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[cleaned up]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[set up LED]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Martin Schiller
bc205a34a4 ipq40xx: fritzbox-7530.dts: increase dma coherent pool size
This is needed by the mei driver to be able to download the firmware.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Martin Schiller
cfd42a0098 ipq40xx: add Intel/Lantiq ATM hacks
Similar to the lantiq platform, these are required for DSL support.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[switch to kernel 5.10 and 5.15]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update patches based on UGW 8.5.2.10, remove 5.10 support]
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Daniel Golle
ab3c9ccb61
mediatek: filogic: fix sysupgrade on MMC on the BPi-R3
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.

Fixes: de94587e70 ("mediatek: filogic: don't rely on image preset in flash or sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-16 22:04:55 +00:00
Daniel Golle
86a2dae29a
mediatek: mt7622: fix sysupgrade on MMC on BPi-R64
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.

Fixes: d640cbac0e ("mediatek: mt7622: don't rely on existing image for sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-16 22:04:44 +00:00
Daniel Golle
83c0942ff7
kernel: fix kernel panic in mtk_ppe
The patch that adds support for hw flow-offloading counters on newer
MediaTek SoCs tries to prints acct->packets and acct->bytes in debugfs,
without checking that acct isn't null. This causes a kernel panic when
trying to read /sys/kernel/debug/ppe0/entries on older MediaTek SoCs.
Fix this by adding a check for acct.

Fixes: openwrt#11756
Fixes: 9721a42a27 ("kernel: support hw flow-offloading counters on newer MediaTek SoCs")
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-16 22:04:35 +00:00
Nick Hainke
1cefb14230
archs38: switch to 5.15 by default
It appears that only a few users are using the archs38 SoC. The most
active user of the target has already approved the testing kernel and
so it is very unlikely bugs will be reported in the near future.
Therefore, the target should be directly bumped to 5.15.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-16 20:48:01 +01:00
Dirk Buchwalder
26c095cb4d ipq807x: add Dynalink DL-WRX36
Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 256MB Nand
    •     Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
    •     1x USB 3.0

    •     1 gpio-controlled dual color led (blue/red)

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard (J1004)
        the connector size is a 4-pin 2.0 mm JST PH.
        RX/TX is working, u-boot bootwait is active, secure boot is enabled.

        Notes:
	- Serial is completely deactivated in the stock firmware image.
	- This commit adds only single partition support, that means
	  sysupgrade is upgrading the current rootfs partition.
	- Installation can be done by serial connection or
	  SSH access on OEM firmware

	Installation Instructions:

	Most part of the installation is performed from an initramfs image
	running OpenWrt, and there are two options to boot it.

	Boot initramfs option 1: Using serial connection (3.3V)
	1. Stop auto boot to get to U-boot shell
	2. Transfer initramfs image to device
	   (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
	   Tested using TFTP and a FAT-formatted USB flash drive.
	3. Boot the initramfs image
	   # bootm

	Boot initramfs option 2: From SSH access on OEM firmware
	1. Copy the initramfs image to a FAT-formatted flash drive
	   (tested on single-partition drive) and connect it to device USB port.
	2. Change boot command so it loads the initramfs image on next boot
	   Fallback to OEM firmware is provided.
	   # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
	3. Reboot the device to boot the initramfs
	   # reboot

	Install OpenWrt from initramfs image:
	1. Use SCP (or other way) to transfer OpenWrt factory image
	2. Connect to device using SSH (on a LAN port)
	3. Check MTD partition table.
	   rootfs and rootfs_1 should be mtd18 and mtd20
	   depending on current OEM slot.
	   # cat /proc/mtd
	4. Do a ubiformat to both rootfs partitions:
	   # ubiformat /dev/mtd18 -y -f /path_to/factory_image
	   # ubiformat /dev/mtd20 -y -f /path_to/factory_image
	5. Set U-boot env variable: mtdids
	   # fw_setenv mtdids 'nand0=nand0'
	6. Get offset of mtd18 to determine current OEM slot
	   - If current OEM slot is 1, offset is 16777216  (0x1000000)
	   - If current OEM slot is 2, offset is 127926272 (0x7a00000)
	   # cat /sys/class/mtd/mtd18/offset
	7. Set U-boot env variable: mtdparts
	   If current OEM slot is 1, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
	   If current OEM slot is 2, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
	8. Set U-boot env variable: bootcmd
	   # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
	9. Reboot the device
	   # reboot

        Note: this PR adds only single partition support, that means sysupgrade is
              upgrading the current rootfs partition

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Matthew Hagan
6e03304c76 ipq807x: add Edgecore EAP102
The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be
powered by either PoE or AC adapter.

Device info:
 - IPQ8071-A SoC
 - 1GiB RAM
 - 256MiB NAND flash
 - 32MiB SPI NOR
 - 2 Ethernet ports
 - 1 Console port
 - 2GHz/5GHz AX WLAN
 - 2 USB 2.0 ports

Install instructions:

Prerequistes - TFTP server, preferrably within 192.168.1.0/24
	       Console cable plugged in (115200 8N1 no flow control)

1. Power on device and interrupt u-boot to obtain u-boot CLI

2. set serverip to IP address of the TFTP server:

	`setenv serverip 192.168.1.250`

3. Download image from TFTP server:

	`tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi`

4. Flash ubi image to both partitions and reset:

	`sf probe
	 imxtract 0x44000000 ubi
	 nand device 0
	 nand erase 0x0 0x3400000
	 nand erase 0x3c00000 0x3400000
	 nand write $fileaddr 0x0 $filesize
	 nand write $fileaddr 0x3c00000 $filesize
	 reset`

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
2ddb2057cd ipq807x: Add Xiaomi AX9000
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet:
	* 4x1G RJ45 ports (QCA8075) with 1x status LED per port
	* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* WLAN:
	* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
	* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
	* 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate
	* 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate
* USB: 1x USB3.0 Type-A port
* LED-s:
	* System (Blue and Yellow)
	* Network (Blue and Yellow)
	* RGB light bar on top in X shape
* Buttons:
	* 1x Power switch
	* 1x Soft reset
	* 1x Mesh button
* Power: 12V DC Jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd21 and mtd22 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Dirk Buchwalder
bd17683261 ipq807x: add QNAP 301w
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
          (contains art and u-boot-env)
    •     Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate

    •     LEDs:
          7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard.
        RX/TX is working, bootwait is active, secure boot is not enabled.

        SSH can be activated in the stock firmware, hold WPS button til the second beep
	(yes the router has a buzzer)
        SSH is available on port 22200, login with user admin and
	password "mac address of the router".

        Installation Instructions:

            • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
            • stop auto boot
            • setenv serverip 192.168.10.1
            • setenv ipaddr 192.168.10.10
            • tftpboot the initramfs image
              (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
            • bootm

            • make sure that current_entry is set to "0":
              "fw_printenv -n current_entry" should be print "0". If not,
	       do "fw_setenv current_entry 0"
            • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
	          to the device to /tmp folder
            • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
              this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
            • reboot

        Note: this leaves the second kernel / rootfs parition untouched. So if you want
              to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
	       "saveenv", "bootipq".
              Stock firmware should start from the second partition.
	      Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
	      in the first partitions

        Make 10G Aquantia phy's work:
              The aquantia phy's need a firmware to work. This can either be loaded
	      in linux with a userspace tool or in u-boot.

              I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
	      aq_load_fw available in u-boot. But first the right firmware needs to write
	      to the 0:ETHPHYFW mtd partition (it is empty on my device)

              Grab the ethphy firmware image from:
	      https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
	      and scp that to openwrt.

              Check the 0:ETHPHYFW partition number:
              cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.

              Backup the 0:ETHPHYFW partition:
              dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.

              Write the new firmware image to the 0:ETHPHYFW partition:
              "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".

              Reboot to u-boot.

              Check if aq_load_fw is working:

              "aq_load_fw 0", that checks the firmware and if successfull,
	      loads iram and dram to one of the aquantia phy's.

              If that worked, add the aq_load_fw to the bootcmd:
              setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"

              "saveenv"

              "reset"

              Board reboots and the firmware load to both phy's should start and
	      then openwrt boots.

              Check if the 10G ports work.

              Note: lan port labeled "10G-2" is configured as WAN port as per default.
	      All other port are in the br-lan. This can be changed in the network config.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Dirk Buchwalder
a36fc589fe ipq807x: add Edimax CAX1800
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.

Specifications:

    •     CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
    •     RAM: 512MB of DDR3
    •     Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
    •     Ethernet: 1x 1G RJ45 port (QCA8072) PoE
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
          5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate

    •     LEDs:
          3 x GPIO-controlled System-LEDs
          (form one virtual RGB System-LED)
            black_small_square  Buttons: 1x soft reset
            black_small_square  Power: 12V DC jack or PoE (802.3af )

        An unpopulated serial header is onboard.
        RX/TX is working, bootwait is active, secure boot is not enabled.

        SSH can be activated in the stock firmware, but it drops only
        to a limited shell .

        Installation Instructions:

            black_small_square obtain serial access
            black_small_square stop auto boot

            black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
            black_small_square bootm

            black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
	      to the device
            black_small_square write the image to the NAND:
            black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
            black_small_square ubiformat /dev/mtd0 -f -y  openwrt-ipq807x-generic-edimax_cax1800-squashfs-
              nand-factory.ubi
            black_small_square reboot

	Note: Device is not using dual partitioning (NAND contains other partitions
        with different manufacture data etc.)
	Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Zhijun You
8253cb2de5 ipq807x: add Redmi AX6
Redmi AX6 is a budget 802.11ax dual-band router/AP

Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 128MB NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LEDs:
	* System (Blue/Yellow)
	* Network (Blue/Yellow)
*Buttons: 1x soft reset
*Power: 12V DC jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Zhijun You <hujy652@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
8364f08164 ipq807x: add Xiaomi AX3600
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
	* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
	* System (Blue and Yellow)
	* IoT (Blue)
	* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
bc120521db ipq807x: include kmods for wired networking by default
Include NSS DP and SSDK (Pulled as dependency) by default on ipq807x to
provide wired networking to the target.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
d092dee9ed ipq807x: include ath11k-ahb by default
All of the IPQ807x devices support having 2 radios, so lets include the
required driver as well.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
4359d10b01 kernel: 5.15: add missing kernel configuration options
Found during compilation of ipq807x with ALL_NONSHARED.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
b5f32064ed ipq807x: add Qualcomm Atheros IPQ807x target
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
	* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
	* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
	* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
	* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
	* 5G: 2x2/80MHz (IPQ8070A)
	* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
	* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)

Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.

SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
6c9329e088 generic: 5.15: add MHI SBL callback for ath11k
This adds the MHI SBL callback that ath11k will utilize in order to
support multiple PCI cards or AHB+PCI combo which currently does not
work due to QRTR ID-s conflicting.

This is a prerequisite for the mac80211 patch targeting ath11k as it
uses MHI from kernel.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
c01641bcc7 archs38: mark as source-only
archs38 seems to be pretty much unused, usually only treewide changes or
kernel bumps in order to branch off new stable are done to it.

Considering that target only support some Synopsis HS38 ARC reference
boards and no consumer hardware so mark the target as source-only to stop
using Buildbot resources on building the target and packages for it.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 11:05:34 +01:00
Harm Berntsen
09f313bfd7 ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.

Specifications
--------------
SOC   : Mediatek MT7621AT
ETH   : Two 1 gigabit ports, built into the SOC
WIFI  : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED   : Power (green+red)
LED   : WiFi (green+blue)
LED   : WPS (green+red)
LED   : Followme (green+red)
Power : 12 VDC, 1A barrel plug

Winbond variant:
RAM   : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1

Macronix variant:
RAM   : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec  4 2017 - 11:37:57), Ralink 5.0.0.1

Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.

The pinout is: VCC (the square), RX, TX, GND.

Installation
------------
See the Wiki page [1] for more details, it comes down to:

1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
   connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
   environment located at 0x30000

Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.

MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use      | address          | example           |
+----------+------------------+-------------------+
| Device   | label            | 00:00:00:11:00:00 |
| Ethernet | + 3              | 00:00:00:11:00:03 |
| 2g       | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g       | + 1              | 00:00:00:11:00:01 |
+----------+------------------+-------------------+

The label address is stored in ASCII in the board_data partition

Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
  both partitions for more storage space.

Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
  macaddr_add
- Only the power LED is configured by default

References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653

Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
2023-01-15 13:41:02 +01:00
Florian Eckert
1e0604e0d1 kernel/x86: fix typo
Fix typo for KernelPackage w83627hf-wdt.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2023-01-15 13:30:09 +01:00
Vincent Tremblay
9e4ede8344 ipq40xx: add support for Linksys WHW03 V2
SOC:             Qualcomm IPQ4019
WiFi 1:          QCA4019 IEEE 802.11b/g/n
WiFi 2:          QCA4019 IEEE 802.11a/n/ac
WiFi 3:          QCA8888 IEEE 802.11a/n/ac
Bluetooth:       Qualcomm CSR8811 (A12U)
Zigbee:          Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet:        Qualcomm Atheros QCA8072 (2-port)
Flash 1:         Mactronix MX30LF4G18AC-XKI
RAM (NAND):      SK hynix H5TC4G63CFR-PBA (512MB)
LED Controller:  NXP PCA9633 (I2C)
Buttons:         Single reset button (GPIO).

- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.

Bluetooth:
========
- Fully working with the following caveats:
  - RFKILL need to be enabled in the kernel.
  - An older version of bluez is needed as bccmd is needed to configure the chip.

Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.

Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.

The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.

It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2023-01-15 12:55:38 +01:00
John Audia
2835df54ab kernel: bump 5.10 to 5.10.163
Removed upstreamed:
  generic/101-Use-stddefs.h-instead-of-compiler.h.patch[1]

All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.163&id=ddd2bb08bd99b7ee4442fbbe0f9b80236fdd71d2

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-14 22:31:38 +01:00
Filip Milivojevic
990419dac3 ramips: cudy wr1300v1 reduce SPI freq to 10000000
Reducing SPI flash frequency allows the build to boot on both old variants
with W25Q128 chip and new variants with XM25QH128C chip.

The old 80000000 value only boots on devices with the W25Q128 flash.

This is also the change Cudy themselves made in their openwrt builds and
their .dts file.

Removed m25p,fast-read as it is not needed with slower speeds.

Signed-off-by: Filip Milivojevic <zekica@gmail.com>
2023-01-14 19:25:06 +01:00
Marcin Gajda
700c47a5f6 ipq40xx: Add support ZTE MF18A
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification

SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..)  modules ( not supported by orginal software )
Installation

 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
   with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :

    VCC (3.3V). Do not use unless you need to source power for the converer from it.
    TX
    RX
    GND

    Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.

 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2

 3.Connect TFTP server to RJ-45 port (WAN/LAN1).

 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
    setenv serverip 192.168.0.2
    setenv ipaddr 192.168.0.1
    set fdt_high 0x85000000
    tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
    bootm 0x84000000

 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:

WEB PARITION

cat /dev/mtd8 > /tmp/mtd8.bin
scp /tmp/mtd8.bin root@YOURSERVERIP:/
rm /tmp/mtd8.bin
ROOT PARITION

cat /dev/mtd9 > /tmp/mtd9.bin
scp /tmp/mtd9.bin root@YOURSERVERIP:/
rm /tmp/mtd9.bin

If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000

 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it

 7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin

previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.

Back to Stock (!!! need original dump taken from initramfs !!!) -------------

Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000

This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000

This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000

After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router

As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com

Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2023-01-14 19:19:36 +01:00
Luo Chongjun
b352124cd2 ath79: Fix glinet ar300m usb not working
glinet forum users reported the problem at
https://forum.gl-inet.com/t/gl-ar300m16-openwrt-22-03-0-rc5-usb-port-power-off-by-default/23199

The current code uses the regulator framework to control the USB power
supply. Although usb0 described in DTS refers to the regulator by
vbus-supply, but there is no code related to regulator implemented
in the USB driver of QCA953X, so the USB of the device cannot work.

Under the regulator framework, adding the regulator-always-on attribute
fixes this problem, but it means that USB power will not be able to be
turned off. Since we need to control the USB power supply in user space,
I didn't find any other better way under the regulator framework of Linux,
so I directly export gpio.

Signed-off-by: Luo Chongjun <luochongjun@gl-inet.com>
2023-01-14 19:13:42 +01:00
Keith Harrison
c13263ca07 ramips: add support for D-Link DIR-1935 A1
Add support for D-Link DIR-1935 A1 based on similarities to DIR-882 A1,
DIR-867 A1 and other DIR-8xx A1 models. Existing DIR-882 A1 openwrt
"factory" firmware installs without modificaitons via the D-Link
Recovery GUI and has no known incompatibilities with the DIR-1935 A1.

Changes to be committed:
       new file:   target/linux/ramips/dts/mt7621_dlink_dir-1935-a1.dts
       modified:   target/linux/ramips/image/mt7621.mk
       modified:   target/linux/ramips/mt7621/base-files/etc/board.d/01_leds

Specifications:
* Board: Not known
* SoC: MediaTek MT7621 Family
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615 Family (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
        WiFi 5G (green)

Notes:
* 160MHz 5GHz is available in LuCi but does not appear to work (i.e. no
  SSID is visible in wifi scanning apps on other devices) with either
  official DIR-882 A1 firmware or a test build for the DIR-1935 A1 based
  on the 22.03.2 branch. 80 MHz 5GHz works.

Serial port:
* Untested (potential user damage/error)
* Expected to be identical to other DIR-8xx A1 models:
	* Parameters: 57600, 8N1
	* Location: J1 header (close to the Reset, WiFi and WPS buttons)
	* Pinout: 1 - VCC
		  2 - RXD
	          3 - TXD
		  4 - GND

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

Signed-off-by: Keith Harrison <keithh@protonmail.com>
2023-01-14 19:09:56 +01:00
Felix Baumann
acd3b5e83b ramips: Alternative name Asus RT-AX1800U for Asus RT-AX53U
The Asus RT-AX1800U is identical to the already supported Asus RT-AX53U.
Use the ALT0 buildroot tags to show both devices.

Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-01-14 19:05:41 +01:00
Jo Deisenhofer
f204c812e9 ramips: add support for xiaomi RA75 Range Extender
This device is a 'Range extender' variant of the Xiaomi 4A router.
Its identical to the 100m non-intl/chinese version as much as it can run
the same firmware, differences being form factor, LEDs, WPS button
and one 100M port only.
The stock firmware differs significantly, being 'app managed only'.

Device specification
--------------------
SoC:      MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi:     MT7612EN 5G-ac 80MHz 2T2R
Flash:    16MB W25Q128BV
DRAM:     64MB built-in SoC
Switch:   built-in SoC
Ethernet: 1x10/100 Mbps
USB:      None
Antennas: 2 x external, non-detachable
LEDs:     2 programmable blue/amber
Buttons:  WPS and reset (hidden)
Housing:  Range Extender / Wall wart
Serial:   115200,8n1

MAC Addresses
-------------
All 3 MACs are read from flash and identical to stock.
Label MAC is WIFI 2G

Installation
------------
No HTML UI on this device, serial console only. The serial connector
is unpopulated but standard size and clearly marked. Flash from the
U-Boot shell at boot by choosing (2) and flashing the sysupgrade file
via tftp.

Recovery/Debricking procedures of the xiaomi 4A and variants should
work, but there currently is no official source for the stock firmware.

Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
2023-01-14 19:02:21 +01:00
Jo Deisenhofer
ab402f3d23 ramips: Move LED definition out of included dtsi into dts
Prepare for a new target with different led definitions that wants to
include this dtsi. The resulting dtb are unchanged, verified with dtdiff

Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
2023-01-14 19:02:20 +01:00
Mikhail Zhilkin
1a35edfbdb ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |              J2
    |
    +--- Don't connect

Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
   with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 't'
3. Load and run OpenWrt initramfs image:
      tftpboot
      bootm
4. Once inside OpenWrt, switch to the first boot image:
      fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Back to Stock
-------------
1. Run in the OpenWrt shell:
      fw_setenv BootImage 1
      reboot

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
   the OEM firmware

MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
|         | MAC example 1     | MAC example 2     | Algorithm   |
+---------+-------------------+-------------------+-------------+
| label   | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| LAN     | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WAN     | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2     |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).

Notes
-----
[1] WAN MAC address:
   a. First octet of WAN MAC is differ than others and OUI is not related
      to TP-Link company. This probably should be fixed.
   b. Flipping bits in first octet and hex delta are different for the
      different MAC examples:
      +-----------------+----------------+----------------+
      |                 | Example 1      | Example 2      |
      +-----------------+----------------+----------------+
      | LAN             | 68 = 0110 1000 | 50 = 0101 0000 |
      | MAC (1st octet) |         ^ ^ ^  |                |
      +-----------------+----------------+----------------+
      | WAN             | 72 = 0111 0010 | 54 = 0101 0100 |
      | MAC (1st octet) |         ^ ^ ^  |            ^   |
      +-----------------+----------------+----------------+
      | HEX delta       | 0xa            | 0x4            |
      +-----------------+----------------+----------------+
      | DEC delta       | 4              | 4              |
      +-----------------+----------------+----------------+
   c. DEC delta is a constant (4). This looks like a mistake in OEM
      firmware and probably should be fixed.
   Based on the above, I decided to keep correct OUI and make WAN MAC =
   label + 1.

[2] Bootloaders
   The device contains 3 bootloaders:
   - First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
     located on NAND Flash to load next full-feature Uboot.
   - Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
     bootloader includes recovery webserver. Requires special uImages to
     continue the boot process:
        0x00 (os0, os1) - firmware uImage
        0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
   - Additionally, both slots of the original TP-Link firmware contains
     Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
     magics and CRCs. We don't use this U-Boot with OpenWrt.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-14 18:36:33 +01:00
INAGAKI Hiroshi
1f5f2e588a ramips: add support for ELECOM WRC-2533GHBK2-T
ELECOM WRC-2533GHBK2-T is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC      : MediaTek MT7621A
- RAM      : DDR3 128 MiB
- Flash    : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN     : 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
  - Switch : MediaTek MT7530 (SoC)
- LED/keys : 4x/3x (2x buttons, 1x slide-switch)
- UART     : through-hole on PCB
  - J4: 3.3V, RX, GND, TX from SoC side
  - 57600n8
- Power    : 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-2533GHBK2-T normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

MAC addresses:

LAN    : BC:5C:4C:xx:xx:FD (Config,  "ethaddr" (text))
WAN    : BC:5C:4C:xx:xx:FC (Config,  "wanaddr" (text), Label)
2.4 GHz: BC:5C:4C:xx:xx:FE (Factory, 0x4       (hex))
5 GHz  : BC:5C:4C:xx:xx:FF (Factory, 0x8004    (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-14 15:41:00 +01:00
INAGAKI Hiroshi
9fe648166e ramips: separate and update dtsi of ELECOM WRC-2533GHBK-I/GHBK2-T
ELECOM WRC-2533GHBK2-T has the almost same hardware as WRC-2533GHBK-I,
so separate the common parts from dts to dtsi.
Additionaly, add color/function properties to LED nodes and change the
trigger of wlan2g/wlan5g LED to "phy*tpt" trigger.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-14 15:41:00 +01:00
Markus Stockhausen
c03e458c86 realtek: Follow kernel comment style recommendation
While Linus is fine with longer code lines, comments should still be
within the 80 char limit.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
2023-01-13 22:34:16 +01:00
Davide Fioravanti
ea42a04161 realtek: add support for Netgear GS750E
This is an RTL8393-based switch with 48 RJ-45 and 2 SFP ports.

Hardware
--------
SoC:	Realtek RTL8393M
RAM:	128MB DDR3 (Nanya NT5CC64M16GP-DI)
FLASH:	8MB NOR (Macronix MX25L6433F)
ETH:	48x 10/100/1000 Mbps RJ-45 Ethernet
SFP:	2x SFP
BTN:
  - 1x	Reset button
LEDS:
  - 50x	Green-Amber leds: lan/sfp status
  - 1x	Green led: power (Always on)
UART:
  - 115200-8-N-1 (CN3, pin-out on PCB)

Everything works correctly except for the 2 SFP ports that are not
working unless you enable it every boot in U-Boot with the command:
	rtk network on

Installation
------------
You can install Openwrt using one of the following methods.

Warning: flashing OpenWrt will delete your current configuration.
Warning 2: if the -factory.bix file is not available anymore, you must
follow Method 2.

Method 1:
Check the firmware version currently running on your switch. If you are
running FW V1.0.1.10 or greater, you have to download the firmware
V1.0.1.8 from Netgear website and then flash this version. When the
switch restarts, it should be on version V1.0.1.8. Now you can get the
OpenWrt -factory.bix file and then flash it using the OEM web interface.

Method 2 (requires the UART connection):
Boot the -initramfs-kernel.bin image from U-Boot with these commands:
	rtk network on;
	tftpboot 0x8f000000 openwrt-realtek-rtl839x-netgear_gs750e-initramfs-kernel.bin;
	bootm;
And then flash the -sysupgrade.bin file from OpenWrt.

Revert to stock
---------------
Get the stock firmware from the Netgear website and flash it using the
OpenWrt web interface. Remember to not keep the current configuration
and check the "Force upgrade" checkbox

Once reverted to stock the firmware could complain in the UART console
about mtdblock3 and/or mtdblock4 not being mounted correctly but it
seems to work anyway without any problems. Sample error:
	mount: Mounting /dev/mtdblock4 on /mntlog failed: Input/output error

If you want to get rid of these error messages you can boot the
-initramfs-kernel.bin image from U-Boot with these commands:
	rtk network on;
	tftpboot 0x8f000000 openwrt-realtek-rtl839x-netgear_gs750e-initramfs-kernel.bin;
	bootm;

And then erase the corresponding partitions using the command:
	For mtdblock3:
		mtd erase jffs2_cfg
	For mtdblock4:
		mtd erase jffs2_log

Now you can reboot the switch and the errors should be gone

Note
----
To get the SFP ports fully working, all the right GPIOs must be found.
In the GPL sources I found these:
 - GPIO_14: SFP_TX_DIS1;
 - GPIO_19: SFP_TX_DIS0;

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2023-01-13 22:28:36 +01:00
Davide Fioravanti
79e0b503a4 realtek: rtl839x: enable driver for virtual mtd_concat devices in config
Enable the driver for the rtl839x target. It's required at least for
Netgear GS750E

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2023-01-13 22:22:38 +01:00
John Audia
843e3dace7 kernel: bump 5.15 to 5.15.87
Removed upstreamed:
  generic/hack-5.15/290-net-dsa-mv88e6xxx-depend-on-PTP-conditionally.patch[1]

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.87&id=945e58bdaf6faf6e3f957d182244fa830acddab4

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-13 22:04:22 +01:00
Nick Hainke
feeec1e14f archs38: enable 5.15 testing kernel
Add 5.15 as testing kernel.

Tested-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 21:55:58 +01:00
Nick Hainke
f43dc6fd74 archs38: 5.15: copy config from 5.10
Copy config from 5.10 to 5.15.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 21:55:57 +01:00
Florian Maurer
2e3d1edf59 lantiq: xrx200: Fix wifi LED on o2 box 6431
Wifi LED did not work using phy0radio, which somehow slipped through in
the previous testing

Signed-off-by: Florian Maurer <f.maurer@outlook.de>
2023-01-11 22:01:56 +01:00
Michal Hrusecky
f6b46c9269 mvebu: backport upstream patch to fix COMPHY reset
Upstream commit [1] included in the Linux kernel version 6.2 was
backported to Linux kernels 6.1.4, 6.0.18. It should be possible that it
is going to be backported even to the 5.15 series, but before it happens,
let's include it here.

It was discovered that on SOC Marvell Armada 3720, which is using e.g.
Turris MOX, and if you are also using it with older ARM Trusted Firmware
v1.5, it is not possible to detect connected USB 3.0 devices, but they
are working just fine when connected with USB 2.0 cable. This patch
fixes it.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/phy/marvell/phy-mvebu-a3700-comphy.c?id=b01d622d76134e9401970ffd3fbbb9a7051f976a

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Michal Hrusecky <michal.hrusecky@turris.com>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[improve commit description, added tag to the patch]
2023-01-11 21:56:36 +01:00
Petr Štetiar
3b669bc3f3 at91: sam9x,sama5: fix racy SD card image generation
We've few low spec (make -j3) build workers attached to the 22.03
buildbot instance which from time to time exhibit following build
failure during image generation (shortened for brewity):

 + dd bs=512 if=root.ext4 of=openwrt-22.03...sdcard.img.gz.img
 dd: failed to open 'root.ext4': No such file or directory

Thats happening likely due to the fact, that on buildbots we've
`TARGET_PER_DEVICE_ROOTFS=y` which produces differently named filesystem
image in the SD card image target dependency chain:

 make_ext4fs -L rootfs ... root.ext4+pkg=68b329da

and that hardcoded `root.ext4` image filename becomes available from
other Make targets in the later stages. So lets fix this issue by using
IMAGE_ROOTFS Make variable which should contain proper path to the root
filesystem image.

Fixing remaining subtargets ommited in commit 5c3679e39b ("at91:
sama7: fix racy SD card image generation").

Fixes: 5c3679e39b ("at91: sama7: fix racy SD card image generation")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-01-11 15:23:18 +01:00
Philip Prindeville
26595eac05 x86: Add APU6 board support for startup detection
The APU6 is similar to the APU4 except for eth0 having
an SFP cage instead of RJ45.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
2023-01-11 15:16:53 +01:00
Philip Prindeville
5ffa8d06c8 x86: Add definitions for APU6 platform
The board is similar to an APU4 except it has an SFP cage for eth0.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [patch refresh]
2023-01-11 15:16:52 +01:00
Petr Štetiar
5c3679e39b at91: sama7: fix racy SD card image generation
We've few low spec (make -j3) build workers attached to the 22.03
buildbot instance which from time to time exhibit following build
failure during image generation:

 + dd bs=512 if=root.ext4 of=openwrt-22.03-snapshot-r20028-43d71ad93e-at91-sama7-microchip_sama7g5-ek-ext4-sdcard.img.gz.img seek=135168 conv=notrunc
 dd: failed to open 'root.ext4': No such file or directory

Thats likely due to the fact, that on buildbots we've
`TARGET_PER_DEVICE_ROOTFS=y` which produces differently named filesystem
image in the SD card image target dependency chain:

 make_ext4fs -L rootfs ... root.ext4+pkg=68b329da

and that hardcoded root.ext4 becomes available from other target in the
later stages. So lets fix this issue by using IMAGE_ROOTFS Make variable
which should contain proper path to the root filesystem image.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-01-11 15:16:52 +01:00
Christian Marangi
dca1b92ecd
Revert "TODROP: test for ipq4019 target"
This reverts commit 4eb587f7e0.

Pushed by mistake while merging a pr using script.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-11 14:29:44 +01:00
Christian Marangi
4eb587f7e0
TODROP: test for ipq4019 target
COMMIT TO DROP

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-11 14:28:41 +01:00
Christian Marangi
55c32a6ce3
ipq806x: refresh upstreamed patch with kernel version tag
Refresh upstreamed patch with kernel version tag and replace them with
the upstream version.

For krait-cc patch rework them with the upstream changes.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-10 20:59:21 +01:00
Stijn Tintel
f1aa8f34ff sunxi: switch to kernel 5.15
The testing kernel has been available since early 2022, and is running
fine for several people. Let's switch to it by default.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Jan-Niklas Burfeind <openwrt@aiyionpri.me>
2023-01-09 21:39:46 +02:00
Stijn Tintel
55f93085bb qoriq: drop unused kernel config
While switching qoriq to kernel 5.15, the config for kernel 5.10 was
left behind. Drop it.

Fixes: 230f2fccd1 ("qoriq: switch to kernel 5.15")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2023-01-09 21:39:45 +02:00
Hauke Mehrtens
ef3919bea9 layerscape: Add CONFIG_NVMEM_LAYERSCAPE_SFP kernel configuration option
The kernel configuration option is now available on kernel 5.10 and
5.15, add it to the config for 5.15 too.

Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-08 18:51:27 +01:00
Hauke Mehrtens
111b183ca9 at91: Add CONFIG_NVMEM_MICROCHIP_OTPC kernel configuration option
The kernel configuration option is now available on kernel 5.10 and
5.15, add it to the config for 5.15 too.

Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-08 16:10:49 +01:00
Hauke Mehrtens
0627874594 kernel: Refresh kernel patches
Make the patches apply cleanly again.

Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-08 14:55:44 +01:00
Daniel Groth
89eb8b50d1 realtek: dgs-1210-10mp: add full sfp description
Added the full SFP description for both SFP ports (lan9, 10) on D-Link
DGS-1210-10MP, which enables hot-plug detection of SFP modules.
Added the patch to both kernel 5.10 and 5.15 dts files.

Signed-off-by: Daniel Groth <flygarn12@gmail.com>
2023-01-08 11:38:47 +01:00
Arınç ÜNAL
fc33c41c21 ramips: do not use GPIO function on switch pins on certain devices
The pins of the MT7530 switch that translate to GPIO 0, 3, 6, 9 and 12 has
got a function, by default, which does the same thing as the netdev
trigger. Because of bridge offloading on DSA, the netdev trigger won't see
the frames between the switch ports whilst the default function will.

Do not use the GPIO function on switch pins on devices that fall under this
category.

Keep it for:

mt7621_belkin_rt1800.dts: There's only one LED which is for the wan
interface and there's no bridge offloading between the "wan" interface and
other interfaces.

mt7621_yuncore_ax820.dts: There's no bridge offloading between the "wan"
and "lan" interfaces.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-01-08 12:31:52 +08:00
Sebastian Schaper
3c31f6b521 ramips: add support for D-Link DAP-X1860 A1
The DAP-X1860 is a wall-plug AX1800 repeater.

Specifications:
- MT7621, 256 MiB RAM, 128 MiB SPI NAND
- MT7915 + MT7975 2x2 802.11ax (DBDC)
- Ethernet: 1 port 10/100/1000
- LED RSSI bargraph (2x green, 1x red/orange), status
  and RSSI LEDs are incorrectly populated red/orange
  (should be red/green according to documentation)

Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
- Upload factory.bin, confirm flashing
  (seems to work best with Chromium-based browsers)

Revert to OEM firmware:
- tar -xvf DAP-X1860_RevA_Firmware_101b94.bin
- openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \
  -out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ==
- tar -xvf FWImage.st1
- flash kernel_DAP-X1860.bin via Recovery

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2023-01-07 17:56:10 +01:00
Rafał Miłecki
11759a5bf3 kernel: backport of changes & helpers
This code is required for upcoming NVMEM changes.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-07 17:45:17 +01:00
Shiji Yang
9a07895729 mt76: add stand-alone MT7622 firmware package
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
fc9dd3f083 mt76: add stand-alone MT7915 firmware package
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
3dbaf89296 ramips: use default lzma dictionary size for better performance
limit dictionary size patch was introduced to solve the well known
"LZMA ERROR 1 - must RESET board to recover" error.
09b6755946 "ramips: limit dictionary size for lzma compression"

It seems that it has failed recently and we can use lzma loader to fix
this error by adding "$(Device/uimage-lzma-loader)". So just remove it
to use the default parameter -d24 for a higher compression ratio.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 16:56:16 +01:00
Hauke Mehrtens
2f847da79d kernel: Refresh kernel patches
Make the patches apply cleanly again.

Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-07 14:53:10 +01:00
Rafał Miłecki
a1abf71827 kernel: fix bugs added with mac-address-ascii support
1. Check for -EPROBE_DEFER
If it occurs we have to return immediately. Trying other properties
could result in another error and ignoring -EPROBE_DEFER which has a
special meaning.

2. Check for read result
Assuming property->read() success can result in NULL pointer
dereference. It happens e.g. for "mac-address" with NVMEM cell
containing invalid MAC.

3. Simplify code
Don't move cell reading & nvmem_cell_put() into a loop. Simplify loop
code.

Fixes: ecd81de7a5 ("ath79: add nvmem cell mac-address-ascii support")
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-07 12:02:30 +01:00
Jan Hoffmann
7c574525ee realtek: don't relocate kernel on HPE 1920 series
This is no longer needed now that the kernel is built with a load
address that matches the one hard-coded in the bootloader.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2023-01-07 11:16:59 +01:00
David Bauer
e4a76673ff ath79: combine UniFi AC dual firmware-partitions
In order to maximize the available space on UniFi AC boards using a
dual-image partition layout, combine the two OS partitions into a single
partition.

This allows users to access more usable space for additional packages.

Don't limit the usable image size to the size of a single OS partition.
The initial installation has to be done with an older version of OpenWrt
in case the generated image exceeds the space of a single kernel
partition in the future.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-07 01:32:58 +01:00
David Bauer
8036fb8dd0 ramips: combine USW-Flex dual firmware-partitions
In order to maximize the available space on USW-Flex boards using a
dual-image partition layout, combine the two OS partitions into a single
partition.

This allows users to access more usable space for additional packages.

Don't limit the usable image size to the size of a single OS partition.
The initial installation has to be done with an older version of OpenWrt
in case the generated image exceeds the space of a single kernel
partition in the future.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-07 01:32:58 +01:00
David Bauer
eded295cd7 ath79: combine OCEDO dual firmware-partitions
In order to maximize the available space on OCEDO boards using a
dual-image partition layout, combine the two OS partitions into a single
partition.

This allows users to access more usable space for additional packages.

Don't limit the usable image size to the size of a single OS partition.
The initial installation has to be done with an older version of OpenWrt
in case the generated image exceeds the space of a single OS
partition in the future.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-07 01:32:58 +01:00
Rafał Miłecki
69ea580882 treewide: update NVMEM symbols
Fixes: 8dfe69cdfc ("kernel: update nvmem subsystem to the latest upstream")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-07 01:30:31 +01:00
Rafał Miłecki
8dfe69cdfc kernel: update nvmem subsystem to the latest upstream
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-06 22:08:03 +01:00
Enrico Mioso
d3e89e69c5 mvebu: harmonize GL.iNet GL-MV1000 MTD partitions layout with vendor
The GL-MV1000 ships with a 16MB spi-nor flash, containing a copy of the stock GL.iNet firmware.
Add the corresponding flash areas, so our view matches the one of the in-flash stock firmware.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2023-01-06 19:59:42 +01:00
Tim Harvey
af5635e6ca octeontx: add sqaushfs and ramdisk to features
Add squashfs and ramdisk to features as these are commonly used images
for the octeontx.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-01-06 19:44:35 +01:00
Leon M. Busch-George
f6d394e9f2 ramips: add support for Cudy M1800
Specifications

  SoC:       MT7621
  CPU:       880 MHz
  Flash:     32 MiB
  RAM:       256 MiB
  WLAN:      MT7915 WiFi 6 (2.4/5 GHz)
  Ethernet:  2x Gbit ports

                  MAC
LAN        b4:4b:d6:2e:c7:b0 (label)
WAN        b4:4b:d6:2e:c7:b1
WiFi 2.4   00:0c:43:26:46:08
WiFi 5     00:0c:43:26:59:97

Installation

There are two known options:
1) The Luci-based UI.
2) Press and hold the reset button during power up.
   The router will request 'recovery.bin' from a TFTP server at
   192.168.1.88.

Both options require a signed firmware binary.
The openwrt image supplied by cudy is signed and can be used to
install unsigned images.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2023-01-06 19:22:52 +01:00
Leon M. Busch-George
ed7c1a504e kernel: add patch to support en25qh256a
The EN25QH256A variant of the EN25QH256 doesn't initialize correctly from SFDP
alone and only accesses memory below 8m (addr_width is 4 but read_opcode takes
only 3 bytes).

Set SNOR_F_4B_OPCODES if the flash chip variant was detected using hwcaps.

The fix submitted upstream uses the PARSE_SFDP initializer that is not
available in the kernel used with Openwrt.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2023-01-06 19:22:52 +01:00
Joe Mullally
4965cbd259 ath79: tiny: Do not build TPLink WPA8630Pv2 by default
22.03.1+ and snapshot builds no longer fit the 6M flash space
available for these models.

This disables failing buildbot image builds for these devices.
Images can still be built manually with ImageBuilder.

Signed-off-by: Joe Mullally <jwmullally@gmail.com>
2023-01-06 18:52:01 +01:00
Florian Eckert
744a5ab9ce target/imagebuilder: add help text and rename whatdepends to package_whatdepens
Add the command `package_whatdepends` to show all package that have a
dependency to this packages.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2023-01-06 18:44:45 +01:00
Florian Eckert
c75a565d2c target/imagebuilder: update help text for manifest target
- Add a help text for the manifest command.
- Unify command detail help text to use `manifest`.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2023-01-06 18:44:45 +01:00
Florian Eckert
e1cf4688ec target/imagebuilder: change help text for image build
Using command `image` to unify help text.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2023-01-06 18:44:44 +01:00
Florian Eckert
7b60dba954 target/imagebuilder: add depends target to show all package that gets installed
This commits adds the makefile targets `depends` this wrapper is a call
to `opkg depends`. This command shows which runtime dependencies exist
if this package is installed into the image.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2023-01-06 18:44:44 +01:00
Stefan Kalscheuer
f193f2d1a0 ath79: convert UBNT Aircube AC WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Merge art into partition node.

Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
2023-01-06 18:20:31 +01:00
Maxim Anisimov
dbebfb88b5 ramips: add support for Keenetic KN-1613
Keenetic KN-1613 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7628AN.

Specification:
- System-On-Chip: MT7628AN
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 4x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): SoC Built-in 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-keenetic_kn-1613-squashfs-factory.bin"
   to "KN-1613_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-06 17:53:10 +01:00
Maxim Anisimov
4eeecf41cf ramips: enable mtd virtual concat support for mt76x8 subtarget
This is required for upcoming Keenetic KN-1613 support

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-06 17:53:10 +01:00
Vincent Tremblay
2fab942ce1 generic: fix silicon labs spidev bindings
Fix Silicon Labs bindings in the spidev driver

Some bindings for Silicon Labs chips already exists upstream.
These bindings can be found in trivial-devices.yaml.

The existing bindings are using "silabs" instead of "siliconlabs" to
identify the manufacturer.

This commit add two submitted patches for silabs chips and rename the
manufacturer in the different DTS for more coherence.

Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2023-01-06 16:01:10 +01:00
Michael Pratt
e085812a7d ath79: add support for Fortinet FAP-221-B
FCC ID: U2M-CAP4100AG

Fortinet FAP-221-B is an indoor access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

Hardware and board design from Senao

**Specification:**

 - AR9344 SOC		2G 2x2, 5G 2x2, 25 MHz CLK
 - AR9382 WLAN		2G 2x2 PCIe, 40 MHz CLK
 - AR8035-A PHY		RGMII, PoE+ IN, 25 MHz CLK
 - 16 MB FLASH		MX25L12845EMI-10G
 - 2x 32 MB RAM		W9725G6JB-25
 - UART at J11		populated, 9600 baud
 - 6 LEDs, 1 button	power, ethernet, wlan, reset

  Note:	ethernet LEDs are not enabled
	because a new netifd hotplug is required
	in order to operate like OEM.
	Board has 1 amber and 1 green
	for each of the 3 case viewports.

**MAC addresses:**

1 MAC Address in flash at end of uboot
ASCII encoded, no delimiters
Labeled as "MAC Address" on case
OEM firmware sets offsets 1 and 8 for wlan

  eth0 *:1e	uboot 0x3ff80
  phy0 *:1f	uboot 0x3ff80 +1
  phy1 *:26	uboot 0x3ff80 +8

**Serial Access:**

Pinout: (arrow) VCC GND RX TX

Pins are populated with a header and traces not blocked.
Bootloader is set to 9600 baud, 8 data, 1 stop.

**Console Access:**

Bootloader:

Interrupt boot with Ctrl+C
Press "k" and enter password "1"
OR
Hold reset button for 5 sec during power on
Interrupt the TFTP transfer with Ctrl+C

to print commands available, enter "help"

OEM:

default username is "admin", password blank
telnet is available at default address 192.168.1.2
serial is available with baud 9600

to print commands available, enter "help"
or tab-tab (busybox list of commands)

**Installation:**

Use factory.bin with OEM upgrade procedures
OR
Use initramfs.bin with uboot TFTP commands.
Then perform a sysupgrade with sysupgrade.bin

**TFTP Recovery:**

Using serial console, load initramfs.bin using TFTP
to boot openwrt without touching the flash.
TFTP is not reliable due to bugged bootloader,
set MTU to 600 and try many times.
If your TFTP server supports setting block size,
higher block size is better.
Splitting the file into 1 MB parts may be necessary

example:

$ tftpboot 0x80100000 image1.bin
$ tftpboot 0x80200000 image2.bin
$ tftpboot 0x80300000 image3.bin
$ tftpboot 0x80400000 image4.bin
$ tftpboot 0x80500000 image5.bin
$ tftpboot 0x80600000 image6.bin
$ bootm 0x80100000

**Return to OEM:**

The best way to return to OEM firmware
is to have a copy of the MTD partitions
before flashing Openwrt.

Backup copies should be made of partitions
"fwconcat0", "loader", and "fwconcat1"
which together is the same flash range
as OEM's "rootfs" and "uimage"
by loading an initramfs.bin
and using LuCI to download the mtdblocks.

It is also possible to extract from the
OEM firmware upgrade image by splitting it up
in parts of lengths that correspond
to the partitions in openwrt
and write them to flash,
after gzip decompression.

After writing to the firmware partitions,
erase the "reserved" partition and reboot.

**OEM firmware image format:**

Images from Fortinet for this device
ending with the suffix .out
are actually a .gz file

The gzip metadata stores the original filename
before compression, which is a special string
used to verify the image during OEM upgrade.

After gzip decompression, the resulting file
is an exact copy of the MTD partitions
"rootfs" and "uimage" combined in the same order and size
that they appear in /proc/mtd and as they are on flash.

OEM upgrade is performed by a customized busybox
with the command "upgrade".
Another binary, "restore"
is a wrapper for busybox's "tftp" and "upgrade".

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-01-06 15:34:07 +01:00
Michael Pratt
766de7013f ath79: allow skipping hash for Senao sysupgrade
Some vendors of Senao boards have a similar flash layout
situation that causes the need to split the firmware partition
and use the lzma-loader, but do not store
checksums of the partitions or otherwise
do not even have a uboot environment partition.

This adds simple shell logic to skip that part.

Also, simplify some lines and variable usage.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-01-06 15:34:07 +01:00
Michael Pratt
8342c092a0 ath79: use lzma-loader for Senao initramfs images
Some vendors of Senao boards have put a bootloader
that cannot handle both large gzip or large lzma files.

There is no disadvantage by doing this for all of them.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-01-06 15:34:07 +01:00
Rafał Miłecki
457cc59795 kernel: 5.10: update nvmem subsystem to the 5.15 state
This allows cleanly backporting more recent stuff that's important for
OpenWrt.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-06 14:34:37 +01:00
John Audia
2621ddb0be kernel: bump 5.10 to 5.10.162
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-06 12:13:49 +01:00
Pascal Ernster
720b243171 realtek: 5.15: Improve error handling in rtl838x_pie_rule_write()
In target/linux/realtek/files-5.15/drivers/net/dsa/rtl83xx/rtl838x.c,
make rtl838x_pie_rule_write() return non-zero value case of error.

Signed-off-by: Pascal Ernster <git@hardfalcon.net>
2023-01-05 23:09:23 +01:00
Pascal Ernster
a188536ef6 realtek: 5.15: Improve rtl838x dsa driver error handling
Make sure functions calling rtl838x_smi_wait_op() return its return
value in target/linux/realtek/files-5.15/drivers/net/dsa/rtl83xx/rtl838x.c.
This brings the code style in line with the rtl839x implementation.

Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Pascal Ernster <git@hardfalcon.net>
2023-01-05 23:08:13 +01:00
Pascal Ernster
de2dc3feae realtek: return correct error value for phy ops
A behavioural change was introduced with commit 758c88b969 ("realtek:
Whitespace and codestyle cleanup") causing rtl838x_read_phy() and
rtl838x_write_phy() to unconditionally return -ETIMEDOUT. As a result,
probing the device during boot fails:

    Error setting up netdev, freeing it again.
    rtl838x-eth: probe of 1b00a300.ethernet failed with error -5

Fix the bootloop caused by this regression with kernel 5.15 on rtl838x
devices, by properly returning 0 on success.

Tested on a Netgear GS108T v3, a Netgear GS310TP v1, a Zyxel GS1900-8HP
v1 and an HPE 1920-8G.

Fixes: 758c88b969 ("realtek: Whitespace and codestyle cleanup")
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Pascal Ernster <git@hardfalcon.net>
2023-01-05 23:08:04 +01:00
Olliver Schinagl
44e0785285 realtek: Migrate to upstream generic MIPS addresses
Upstream generic MIPS uses 0x80100000 and 0x80100400 for the LOADADDR
and ENTRY addresses. As we do not want to diverge from upstream and
patch upstream when not needed, adjust our addresses as well to be
future proof.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Tested-by: Jan Hoffmann <jan@3e8.eu> # HPE 1920-8G, HPE 1920-48G
2023-01-05 21:59:20 +01:00
Ignas Poklad
7801e814dd ramips: add Unielec U7621-06 32M build target
Add 32M build target

Rest of the details as per commit 46ab81e405 ("ramips add support for
UniElec U7621-06")

Signed-off-by: Ignas Poklad <ignas2526@gmail.com>
2023-01-05 00:10:14 +01:00
Nick Hainke
aa6c8c38ea ath79: convert Netgear WNDAP360 WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Merge art into partition node.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-04 23:59:09 +01:00
Florian Maurer
0820d62012 lantiq-xrx200: fix wan LED on o2 box 6431
The WIFI LED already worked for me with the latest openwrt 22.03 version.
Wifi LED did not with an older 22.x version (in gluon - there phy0radio did nothing but phy0tpt did show activity

the WAN interface has the name "wan" and not "pppoe-wan" on this device

fixes #7757 (and FS#2987)

Signed-off-by: Florian Maurer <f.maurer@outlook.de>
2023-01-04 23:50:48 +01:00
Shiji Yang
6760c7cbe5 ramips: enable Wi-Fi LED support for Afoundry EW1200
Add LED properties to PCIe node to enable Wi-Fi LED support.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-04 23:32:27 +01:00
Shiji Yang
0eefea2ed7 ramips: enable Wi-Fi LED support for Zbtlink ZBT-WE1326
Add LED properties to PCIe node to enable Wi-Fi LED support.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-04 23:32:27 +01:00
Nikolay Martynov
665c2154ef ramips: add basic support for tp-link er605-v2
This is a MT7621-based device with 128MB NAND flash, 256MB RAM, and a USB port.
The board has headers to attach console. In order for them to work two solder
bridges near those pads need to be made.

The defice has the following partition table:

```
0x000000000000-0x000000080000 : "u-boot"
0x000000080000-0x000000100000 : "u-boot-env"
0x000000100000-0x000000140000 : "factory"
0x000000140000-0x000007e00000 : "firmware"
0x000007e00000-0x000008000000 : "panic-ops"
```

`firmware` partition contains UBI volumes. Unfortunately I accidentally wiped
partition and I no longer have access to it.

`firmware` partition contains 'secondary' U-Boot which is run by 'first' u-boot.
It also contains various configuration partitions that include device info and
MAC address. There also seems to be 'primary' and 'backup' set of 'main' volumes.

U-boot has `mtkupgrade` command that just overrides data on firmware partitions.
Firmware file provided by TP-Link cannot be used with that command.

U-boot also has 'recovery' http server. Unfortunately I was not able to make it
work with manufacturer's firmware.

Manufacturer's firmware essentially contains multiple UBI volumes along with
'partition table'. Unfortunately I no longer can properly run manufacturer's
firmware so I cannot at the moment try to a support for building 'factory' images.

This patch adds support for initramfs image as well as sysupgrade image.

This seems to be pretty standard MT7621 board otherwise.

Things that work:
* network
* leds
* usb
* factory MAC detection

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
2023-01-04 23:19:19 +01:00
Marian Sarcinschi
c4b806d5c4 ramips: add missing LEDs to Asus RT-AX53U
This patch adds the missing LEDs to Asus RT-AX53U.
Based on PR #10400 and patch provided in #11068
 - enable the two LEDs controlled by mt7915e for wireless;
 - add label to power LED so it works properly and fix formatting;
 - add the USB LED;
 - switch LEDs are best left to be controlled by hardware for now.

Co-Authored-By: Ivan Rozhuk <rozhuk.im@gmail.com>
Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Co-Authored-By: Hartmut Birr <e9hack@gmail.com>
Tested-by: Felix Baumann <felix.bau@gmx.de>
Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Marian Sarcinschi <znevna@gmail.com>
2023-01-04 21:56:49 +01:00
Bjoern Dobe
1036545b00
ipq40xx: fix wlan mac address for Aruba AP-303H
Assigns the correct mac address from nvmen to the wlan interfaces.
This Mac address corresponds to the label "Wireless MAC" on the device
and the stock firmware.
Removes duplicate entry of calibration variant for both radios.

Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
2023-01-04 19:17:56 +01:00
Christian Marangi
f4d949b404
generic: 5.15: backport qca8k fixup for mgmt and mdio read/write
Backport qca8k fixup for mgmt and mdio read/write for kernel 5.15 fixup
port dropping and configuration issue.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2023-01-04 16:54:19 +01:00
Seth David Schoen
68f983ba41 generic: 5.10: backport Treat IPv4 segment's lowest address as unicast
Backport patch from kernel 5.14.

Treat only the highest, not the lowest, IPv4 address within a local
subnet as a broadcast address, as subnets do not need two different
broadcast addresses and networking documentation consistently prefers
the highest address as broadcast.

This patch was merged in upstream net-next tree in May 2021 at

https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=94c821c74bf5

This eventually frees up one address per subnet. It matches behavior
suggested in our Internet-Draft, and also the default behavior of OpenBSD
and FreeBSD.

Signed-off-by: Seth David Schoen <schoen@loyalty.org>
2023-01-04 00:48:15 +01:00
John Audia
738b04c881 kernel: bump 5.15 to 5.15.86
Removed upstreamed:
  pending-5.15/101-Use-stddefs.h-instead-of-compiler.h.patch[1]
  ipq806x/patches-5.15/122-01-clk-qcom-clk-krait-fix-wrong-div2-functions.patch[2]
  bcm27xx/patches-5.15/950-0198-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch[3]

Manually rebased:
  ramips/patches-5.15/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch[4]

Added patch/backported:
  ramips/patches-5.15/107-PCI-mt7621-Add-sentinel-to-quirks-table.patch[5]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=c160505c9b574b346031fdf2c649d19e7939ca11
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=a051e10bfc6906d29dae7a31f0773f2702edfe1b
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=ec1727f89ecd6f2252c0c75e200058819f7ce47a
4. Quilt gave this output when I applied the patch to rebase it:
% quilt push -f
Applying patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch
patching file arch/mips/ralink/Kconfig
patching file drivers/pci/controller/Kconfig
patching file drivers/pci/controller/Makefile
patching file drivers/staging/Kconfig
patching file drivers/staging/Makefile
patching file drivers/staging/mt7621-pci/Kconfig
patching file drivers/staging/mt7621-pci/Makefile
patching file drivers/staging/mt7621-pci/TODO
patching file drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
patching file drivers/staging/mt7621-pci/pci-mt7621.c
Hunk #1 FAILED at 1.
Not deleting file drivers/staging/mt7621-pci/pci-mt7621.c as content differs from patch
1 out of 1 hunk FAILED -- saving rejects to file drivers/staging/mt7621-pci/pci-mt7621.c.rej
patching file drivers/pci/controller/pcie-mt7621.c
Applied patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch (forced; needs refresh)

Upon inspecting drivers/staging/mt7621-pci/pci-mt7621.c.rej, it seems that
the original patch wants to delete drivers/staging/mt7621-pci/pci-mt7621.c
but upstream's version was not an exact match.  I opted to delete that
file.

5. Suggestion by hauke: 19098934f9
"This patch is in upstream kernel, but it was backported to the old
staging driver in kernel 5.15."

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-03 23:55:45 +01:00
Robert Marko
a80e630131 oxnas: sata_oxnas: use ata_link_err
Kernel 5.15.86 has backported ("ata: libata: move ata_{port,link,dev}_dbg
to standard pr_XXX() macros") and this is now causing compilation errors
for oxnas SATA driver due to usage of ata_link_printk().

Upstream has migrated to using the appropriate
ata_link_{err, warn, notice, info} calls a while ago so its not affected.

Lets do the same for oxnas SATA driver and use ata_link_err() instead of
ata_link_printk().

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-03 23:40:30 +01:00
Nick Hainke
b069d4ac6d octeontx: add 5.15 testing kernel
Add 5.15 as testing.

Refreshed:
- 0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch

Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-03 20:56:01 +01:00
Nick Hainke
c6edf3bf8c octeontx: 5.15: copy config
Copy config from kernel 5.10 to kernel 5.15.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-03 20:56:01 +01:00
Nick Hainke
bb39ed3f36 zynq: add 5.15 testing kernel
Enable testing kernel.

Reviewed-by: Luis Araneda <luaraneda@gmail.com>
Tested-by: Luis Araneda <luaraneda@gmail.com> (Digilent Zybo Z7-20)
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-03 20:56:01 +01:00
Nick Hainke
45cb7336cb zynq: 5.15: copy config
Copy config from kernel 5.10 to kernel 5.15.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-03 20:56:01 +01:00
Nick Hainke
65f606fb82 ipq40xx: delete files used for building 5.10 kernel
The kernel 5.15 now defaults. Remove unnecessary files.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-03 20:56:01 +01:00
Olliver Schinagl
9260027535 realtek: Migrate to libdeflate
Libdeflate is a more advanced gzip compressor, which allows for faster
decompression, higher compression speed (factor 3-4), while being fully
gzip compatible.

Some comparison
gzip    | libdeflate-gzip | delta  | image [openwrt-realtek-rtl839x-*]
--------+-----------------+--------+-----------------------------------------------
6589174 | 6298794         | 290380 | d-link_dgs-1210-52-initramfs-kernel.bin
6291632 | 6029488         | 262144 | d-link_dgs-1210-52-squashfs-factory_image1.bin
6292270 | 6030128         | 262142 | d-link_dgs-1210-52-squashfs-sysupgrade.bin
6589142 | 6298760         | 290382 | zyxel_gs1900-48-initramfs-kernel.bin
6292264 | 6030122         | 262142 | zyxel_gs1900-48-squashfs-sysupgrade.bin

and changing lzma to (libdeflate-)gzip on existing rtl930x target:
gzip    | libdeflate-gzip | delta  | image [openwrt-realtek-rtl930x-*]
--------+-----------------+--------+--------------------------------------
6816230 | 6510382         | 305848 | zyxel_xgs1250-12-initramfs-kernel.bin

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
2023-01-02 10:18:44 +01:00
Olliver Schinagl
c9a7c00f80 realtek: Disable boston clock
We are not on the 'boston' platform so no point in having that clock
driver enabled.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2023-01-01 22:31:20 +01:00
Hauke Mehrtens
55d176fd0b tfa-layerscape: Use trusted-firmware-a.mk
This converts the trusted firmware arm build Makefile to make use of
the common trusted-firmware-a.mk file. This also fixes the build with
binutils 2.39.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-31 20:02:09 +01:00
Tony Ambardar
6fc334cbdc ipq40xx: sysupgrade: allow flashing Linksys factory firmware
Allow forced flashing of a factory firmware image, after checking for the
correct FIT magic header and Linksys board-specific footer. Details of the
footer are already described in scripts/linksys-image.sh.

This is convenient as it avoids using a TFTP server or OEM GUI, and allows
restoring OEM firmware or installing a "breaking" OpenWrt update (e.g DSA
migration and kernel repartition) directly from the command line.

Devices supported at this time include EA6350v3, EA8300, MR8300 and WHW01.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by:  Wyatt Martin <wawowl@gmail.com> # WHW01
Tested-by:  Tony Ambardar <itugrok@yahoo.com> # EA6350v3
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Tony Ambardar
4b367e2b60 ipq40xx: migrate Linksys WHW01 to DSA and re-enable
Convert Linksys WHW01 network configuration to DSA and re-enable builds.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Tony Ambardar
2a9f3b7717 ipq40xx: fix up Linksys WHW01 board name, device definition
Update the board name defined in DTS to match online documentation and the
name encoded into factory firmware. This helps supports flashing firmware
factory images using 'sysupgrade'.

Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB
instead of the correct 74 MB, and defines factory images which include
extra adjustments/padding that do not match OEM factory images and may
cause problems flashing. Update image size and build recipe to fix these.

Suggested-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Tony Ambardar
cda6f1c832 ipq40xx: re-enable EA6350v3, EA8300, MR8300 builds
Raise the kernel size from 3 MB to 5 MB for EA6350v3, EA8300 and MR8300,
and correspondingly reduce the rootfs size by 2 MB:
  * modify partition definitions in related .dts files
  * modify device kernel/image sizes in generic.mk

Update to compat-version 2.0 to force factory image usage on sysupgrade,
noting the current version 1.1 is an unreleased update for DSA migration.

Also update the compat-version message, explaining the need to run one of
the following console commands to update U-Boot's kernel-size variable
before flashing the OpenWrt factory image.

    fw_setenv kernsize 500000          # (OpenWrt command line)

    setenv kernsize 500000 ; saveenv   # (U-Boot serial console)

Finally, re-enable the 3 devices.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Nicolas TORMO <badulesia.granieri@gmail.com> # MR8300
Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Nick Hainke
00952fb0ca
bcm47xx: replace "Devices-database-update-patch" with upstream patches
Replace "320-MIPS-BCM47XX-Devices-database-update-for-4.x.patch" with
upstream patches:
- 320-v5.17-MIPS-BCM47XX-Add-board-entry-for-Linksys-WRT320N-v1.patch
- 321-v5.17-MIPS-BCM47XX-Add-support-for-Netgear-R6300-v1.patch
- 322-v5.17-MIPS-BCM47XX-Add-support-for-Netgear-WN2500RP-v1-v2.patch
- 323-v6.0-MIPS-BCM47XX-Add-support-for-Netgear-WNR3500L-v2.patch
- 324-v5.17-MIPS-BCM47XX-Add-LEDs-and-buttons-for-Asus-RTN-10U.patch
- 325-v5.17-MIPS-BCM47XX-Define-Linksys-WRT310N-V2-buttons.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-30 20:03:59 +01:00
Nick Hainke
defd016aef
bcm47xx: add tags to upstreamed patches
All of the mtd patches are upstreamed to 5.18. Add tags indicating this.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-30 20:03:56 +01:00
INAGAKI Hiroshi
ef4e1ae18d ramips: enable BBT on NAND in I-O DATA devices
This patch enables MediaTek NAND BBT on I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.).

[WN-AX2033GR]
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[WN-AX1167GR2, WN-DX1167R, WN-DX1200GR, WN-DX2033GR]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-30 16:12:15 +08:00
Chuanhong Guo
d29dbf052a
mediatek: drop redmi-ax6000 variant with modified env
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-30 16:11:59 +08:00
Hauke Mehrtens
7272203022 ramips: Refresh patches
The patch was not applying cleanly any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-29 19:01:15 +01:00
Nick Hainke
3195a992d6
ipq40xx: convert Aruba AP-303H to DSA and enable target again
The target was disabled since noone did the DSA conversion. Add the
conversion and enable it again.

Tested-by: John Walshaw <jjw@myself.com>
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-29 17:39:30 +01:00
Šimon Bořek
2cad88b99f
mpc85xx: change CPU_TYPE from 8540 to 8548
All subtargets as p1010, p1020, p2020 uses e500v2 cores [1] [2] [3] [4],
 so let's force cpu type to 8545 for all mpc85xx target even though
there might exist device with e500v1, but there is no such router supported in OpenWrt
and because of that it does not make sense to to set CPU_TYPE for each subtarget.

All MPC85xx SoC can be found here:
https://www.nxp.com/products/processors-and-microcontrollers/legacy-mpu-mcus/powerquicc-processors:POWERQUICC_HOME#powerquicc-iii-mpc85xx

[1] https://www.nxp.com/docs/en/application-note/AN2807.pdf
[2] https://www.nxp.com/docs/en/fact-sheet/QP1010FS.pdf
[3] https://www.nxp.com/docs/en/product-brief/P1020PB.pdf
[4] https://www.nxp.com/docs/en/fact-sheet/QP20XXFS.pdf

Co-authored-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
2022-12-29 16:49:09 +01:00
Furong Xu
8bac5dc18a mediatek: add new layout for Xiaomi Redmi Router AX6000 for OpenWrt U-Boot
This new layout is only bootable with OpenWrt U-Boot. It reuses the
two crash partions and expands the ubi partion to the end of whole flash.

Do not use this layout with stock U-Boot!

Signed-off-by: Furong Xu <xfr@outlook.com>
2022-12-29 03:00:31 +00:00
Sander Vanheule
045baca10b realtek: deduplicate GS1900 recipes
ZyXEL GS1900 devices with SoCs from both the RTL838x and RTL839x
families share the same image structure and size of the firmware
partition. Additionally, the GS1900-48 recipe provided a parameter for
the zyxel-vers command, but this parameter is not used. Deduplicate the
recipes by moving it to target/linux/realtek/image/common.mk.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-28 22:44:10 +01:00
Sander Vanheule
1e13081064 realtek: fix GS1900-48 firwmare partition
The listed partition size doesn't match the original partition size, and
actually overlaps with the following partition. The partition node name
for the "firmware" partition also has an extra 'b' compared to the
partition offset.

Fixes: 47f5a0a3ee ("realtek: Add support for ZyXEL GS1900-48 Switch")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-28 22:44:10 +01:00
Sander Vanheule
80be0fea03 realtek: fix ZYXELS_VERS for GS1900-48
The GS1900-48 firmware image is identified by the 'AAHN' ID, while the
GS1900-48HP is identified by 'AAHO' [1]. The latter was used, resulting
in the following error message when upgrading via the stock web UI:

  Device only can support firmware from V1.00(AAHN.0) and later version

Fix image generation by using the correct ID.

[1] https://download.zyxel.com/GS1900-48/firmware/GS1900-48_2.70(AAHN.3)C0_2.pdf

Link: https://forum.openwrt.org/t/146533
Fixes: 47f5a0a3ee ("realtek: Add support for ZyXEL GS1900-48 Switch")
Suggested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-28 22:44:10 +01:00
Sander Vanheule
ab8a5f2ea0 realtek: fix default image generation
While cleaning up the makefiles for the realtek target, the order of the
default image generating commands was accidentally changed. This caused
the image signature to end up somewhere in the middle, misaligning the
rootfs. As a result, sysupgrade couldn't verify upgrade images anymore,
and devices end up in a boot loop due to the unaligned (and not found)
rootfs.

Fixes: 94d8b4852b ("realtek: Cleanup Makefiles")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-28 22:44:10 +01:00
Nick Hainke
a14170b6e9 ath79: fix calibration-art for some boards
"0x1000" looks suspicious. By looking at data provided
by @DragonBluep I was able to identify the correct size for
AR9380, AR9287 WiFis. Furthermore, PowerCloud Systems CAP324
has a AR9344 WiFi.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-28 22:36:32 +01:00
Felix Fietkau
6c85c343d2 kernel: fix ethernet regression on mt7986
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-28 20:06:12 +01:00
Felix Baumann
3f1e9f6f3b
ramips: add support for read/write uboot env to Asus RX-AX53U
Add support for read/writing uboot env by renaming the second partition
to its stock label "nvram" and remove the deemed unnecessary
"read-only". Split the first partition "u-boot" in two, in order
to allow `fw_setenv` safe write-access to the uboot environment
variables.

This implements hauke's request from [1].
Based on the patch provided by Shiji Yang.

[1] https://github.com/openwrt/openwrt/pull/10400#discussion_r945153224

Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description, fix some whitespace problem ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-28 14:04:57 +01:00
Birger Koblitz
e143e27c8c realtek: Fix reset register access
The reset register on RTL93xx not merely have bits to execute
a reset of a hardware component, but also configuration bits for
reset procedures. Keep them during executing a reset.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[backport to 5.10 kernel]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-28 16:53:56 +01:00
Álvaro Fernández Rojas
5863363493 bcm27xx: fix BCMGENET kernel config
Revert backported upstream commits 421f8663b3a7 and 8d820bc9d12b, which have
introduced a regression in BCMGENET kconfig that disabled the network driver
for the Raspberry Pi.

Fixes: 0c405bceba ("kernel: bump 5.15 to 5.15.85")
Fixes: e900822326 ("kernel: bump 5.15 to 5.15.84")

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-12-28 13:41:04 +01:00
Felix Fietkau
425945c313 kernel: mediatek: fix WED offload regression on MT7622
Fix dealing with DSA untagging offload

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-27 19:10:05 +01:00
Felix Fietkau
78c51de847 kernel: mediatek: improve ethernet fix for dealing with small fragments
Replace the workaround on MT7986 with a proper fix. Software workaround is
still needed on older chips.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-27 19:10:04 +01:00
Olliver Schinagl
0a83889e89 realtek: Reduce variable scopes
Linus prefers to have loop initializers nice and tightly scoped. In
OpenWRT this has been possible since 41a1a652fb ("kernel: backport
gnu11 upgrade").

This patch cleans up variable scope while trying to do the above for
'simple for loops'.

This cleans up and simplifies some functions and code, and pulls in
variables to a smaller scope.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-12-27 16:33:15 +01:00
Olliver Schinagl
94d8b4852b realtek: Cleanup Makefiles
Our current Makefiles a little bit messy and can be improved somewhat,
both in whitespace and in style.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-12-27 16:33:15 +01:00
Olliver Schinagl
0a931767cf realtek: Replace C++ style comments
The only exception to C++ style comments are SPDX license identifier
markers at the start of C files (even headers have C style markers).

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-12-27 16:33:01 +01:00
Olliver Schinagl
758c88b969 realtek: Whitespace and codestyle cleanup
Fix some ugly whitepsaces and codestyle issues around the realtek sources.

While this is by no means perfect, it catches what it caught.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-12-27 16:31:48 +01:00
Jan Hoffmann
2c40359c5c realtek: add cond_resched to loops accessing the FDB table
A full loop accessing all FDB entries can take several milliseconds
(on RTL839x about 20 ms), so give other kernel tasks a chance to run.
This is especially important for rtl83xx_port_fdb_dump which is itself
called in a loop for all ports by the kernel.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-12-27 16:29:57 +01:00
Jan Hoffmann
ae0a3f88ac realtek: restructure rtl_table_read/write
These two functions are identical apart from writing different values to
the read/write bit. Create a new function rtl_table_exec to reduce code
duplication.

Also replace the unbounded busy-waiting loop. The new implementation may
sleep, but as the hardware typically responds before the first poll, any
callers doing many table accesses still need to make sure not to block
other kernel tasks themselves.

So far, polling timeout errors are only handled by logging an error, but
a return value is added to allow proper handling in the future.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-12-27 16:29:57 +01:00
Jan Hoffmann
9aa123d778 realtek: simplify log messages in rtl83xx_mdio_probe
This function currently prints three messages for every switch port at
KERN_INFO level. This takes a considerable amount of time during bootup
and can even trigger an external watchdog.

Replace these log messages by a single one at KERN_DEBUG level.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-12-27 16:29:57 +01:00
Jan Hoffmann
c94ca63ed4 realtek: don't set L2LEARNING flag in rtl83xx TX header
As learning for the CPU port is now disabled globally, the bit in the
TX header doesn't have any effect anymore. Remove it to make the header
consistent with the global configuration.

Originally, this change was intended to be applied before commit
eb456aedfe ("realtek: use assisted learning on CPU port"), which is
why the commit message incorrectly mentions that the TX header already
disables learning.

The reason for disabling learning on the CPU port in the first place is
that it doesn't work correctly when packets are trapped to the CPU and
then forwarded by the CPU to other ports. In that case, the switch would
incorrectly learn the CPU port as source. An example that triggered this
issue are Multicast Listener Reports and IGMP membership reports.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-12-27 16:29:39 +01:00
Jan-Niklas Burfeind
c7d3bbb909 sunxi: ensure NanoPi R1 has unique MAC address
Ensure the MAC address for all NanoPi R1 boards is assigned uniquely for
each board.

The vendor ships the device in two variants; one with and one without
eMMC; but both without static mac-addresses.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S and R4S in case the EEPROM
chip is not present by generating the board MAC from the SD card CID.

[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R1#Hardware_Spec

Similar too and based on:

commit b5675f500d ("rockchip: ensure NanoPi R4S has unique MAC address")

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-12-25 02:27:55 +01:00
John Audia
5925401007 kernel: bump 5.10 to 5.10.161
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-24 15:24:18 +01:00
John Audia
0c405bceba kernel: bump 5.15 to 5.15.85
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-24 15:22:33 +01:00
Josef Schlehofer
b4da12c2a0
mpc85xx: drop empty patch as it backported to LTS kernel 5.15.70
This patch is part of Linux kernel 5.15.70, the content was removed, but
the empty file is still being carried over the repository, so remove it
once for all

Fixes: e1b009c ("kernel: bump 5.15 to 5.15.70")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-12-24 12:24:46 +01:00
Olliver Schinagl
f649a7b5f3
realtek: 5.15: Fix incorrect switch patches
Add correct header to patche(s) to be correctly used
by git am and have better tracking of it.

See commit f1f97db627 ("realtek: Convert incorrect v5.10 patches").

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-12-24 11:56:21 +01:00
Olliver Schinagl
113fd5b93b
realtek: 5.10: Fix incorrect switch patches
Add correct header to patche(s) to be correctly used
by git am and have better tracking of it.

See commit f1f97db627 ("realtek: Convert incorrect v5.10 patches").

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-12-24 11:56:21 +01:00
Christian Marangi
b2bfea481e
omap: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-23 19:44:22 +01:00
Christian Marangi
314d997e26
pistachio: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-23 19:44:22 +01:00
Christian Marangi
8e2e67d117
octeontx: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-23 19:44:21 +01:00
Christian Marangi
c028e1b1a0
tegra: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-23 19:44:21 +01:00
Christian Marangi
6d7129ef04
zynq: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-23 19:44:21 +01:00
Christian Marangi
64ef920bb7
mxs: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-23 19:44:20 +01:00
Christian Marangi
cada395a50
kirkwood: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-23 19:44:20 +01:00
Christian Marangi
cf49c7d522
gemini: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-23 19:44:20 +01:00
Christian Marangi
13d6048e06
ath25: add generic subtarget
Same game as for 853e4dd306. Add generic
to the filenames.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-23 19:44:14 +01:00
Hauke Mehrtens
376eb2d924 ramips: Fix drivers/pwm/pwm-mediatek-ramips.c compile
The pwmchip_remove() function returns void now. Fix a compile problem in
the drivers/pwm/pwm-mediatek-ramips.c driver.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-23 00:43:39 +01:00
Hauke Mehrtens
92eb787d08 kernel: Move CONFIG_PWM_IMG and CONFIG_PWM_MEDIATEK to generic configuration
In the build of the ramips/mt76x8 target the user gets asked about these
two configuration options, add them to the generic kernel configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-23 00:43:33 +01:00
Hauke Mehrtens
259c014555 kernel: Move CONFIG_DRM_XEN_FRONTEND to generic configuration
The CONFIG_DRM_XEN_FRONTEND configuration symbol is also used by the
layerscape target, move it to the generic kernel configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-23 00:43:23 +01:00
Hauke Mehrtens
f620eb70f1 kernel: Add missing kernel configuration options
This fixes compile of the bmips target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-21 15:15:00 +01:00
Hauke Mehrtens
fbd5573dca kernel: Reorder kernel configuration options
./scripts/kconfig.pl '+' target/linux/generic/config-5.10 /dev/null > target/linux/generic/config-5.10-new
mv target/linux/generic/config-5.10-new target/linux/generic/config-5.10

./scripts/kconfig.pl '+' target/linux/generic/config-5.15 /dev/null > target/linux/generic/config-5.15-new
mv target/linux/generic/config-5.15-new target/linux/generic/config-5.15

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-21 15:14:51 +01:00
Petr Štetiar
5f973c1eef Revert "Revert "mvebu: switch default kernel to 5.15""
This reverts commit 97c77fff28 as commit
8be6350f66 ("generic: 5.15: allow MV88E6xxx built-in when PTP support
disabled") contains the fix, so lets enable kernel 5.15 on mvebu again.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-12-20 14:00:35 +01:00
John Audia
e900822326 kernel: bump 5.15 to 5.15.84
All patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-19 23:51:10 +01:00
Alexander Couzens
17c6fb1054 ath79: image: don't depend on other COMPILE targets
A device COMPILE target should not depend on another COMPILE.
Otherwise race condition may happen.
The loader is very small. Compiling it twice shouldn't
have a huge impact.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2022-12-19 12:27:35 +00:00
Julien Dusser
b893aa7992 ramips: add support for Linksys E5400 and clones
Linksys E5400 is a 2.4/5GHz dual band AC router, based on MediaTek
MT7628AN. This device is also sold as Linksys E2500v4, E5300 and E5350
with the same hardware, but software speed limitations in vendor
firmwares.

Specification:
 * SoC: MT7628AN (580 MHz)
 * RAM: DDR2 64 MiB
 * Flash: 16 MiB NOR (W25Q128BV)
 * Wi-Fi:
   * 2.4GHz: SoC Built-in
   * 5GHz: MT7612EN
 * Ethernet: 5x 100Mbps
   * Switch: SoC built-in
 * UART:
   * 115200, 8N1, 3.3V (real u-boot speed: 119050)
   * Pinout JB4: 1:[3V3] (TXD) (RXD) [NC] (GND)

Flash Layout:
  0x0000000-0x0030000 : "Bootloader"
  0x0030000-0x0040000 : "Config"
  0x0040000-0x0050000 : "Factory"
  0x0050000-0x0ff0000 : "Kernel"
  0x0ff0000-0x1000000 : "CBTinfo"

MAC address:
  LAN: factory 0x28
  WAN: LAN + 1
  2.4G: LAN + 2
  5G: LAN + 3

Installation:
1. Connect to UART, use LF as EOL (not CRLF)
2. Set IP address
  - Press 4 during boot
  - setenv serverip <TFTPSERVER_IP>
  - setenv ipaddr <DEVICE_IP>
  - setenv bootfile openwrt-ramips-mt76x8-linksys_e5400-initramfs-kernel.bin
  - saveenv
  - reset
3. Load Openwrt Kernel image from TFTP:
  - Press 1 during boot
  - IP and filename should be already set
4. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2022-12-18 21:24:57 +01:00
Johnny S. Lee
8be6350f66 generic: 5.15: allow MV88E6xxx built-in when PTP support disabled
As described in commit 97c77fff28
MV88E6xxx driver (NET_DSA_MV88E6XXX) cannot be built-in when PTP
(PTP_1588_CLOCK) is a module in Linux 5.15. But actually it should be
allowed to be built-in when its PTP support (NET_DSA_MV88E6XXX_PTP) is
disabled.

This adds a patch to fix that.

Signed-off-by: Johnny S. Lee <foss@jsl.io>
2022-12-18 16:38:37 +01:00
Alexey Bartenev
3f201d1f8e ramips: add support for SNR-CPE-W4N-MT router
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A

Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
 "Administration/Management/Firmware update/Choose File" in vendor's
 web interface (ip: 192.168.1.10, login: Admin, password: Admin).
 Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 file by "System/Backup/Flash Firmware/Flash image..." in
 LuCI web interface (ip: 192.168.1.1, login: root, no password).
 Wait ~240 seconds.

Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
 Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
 Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
 new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2022-12-17 22:34:44 +01:00
Davide Fioravanti
d9566d059c ath79: add support for KuWFi C910
KuWFi C910 is an 802.11n (300N) indoor router with LTE support.

I can't find anywhere the OEM firmware. So if you want to restore the
original firmware you must do a dump before the OpenWrt flash.

According to the U-Boot, the board name is Iyunlink MINI_V2.

Hardware
--------
SoC:   Qualcomm QCA9533 650/400/200/25/25 MHz (CPU/RAM/AHB/SPI/REF)
RAM:   128 MB DDR2 16-bit CL3-4-4-10 (Nanya NT5TU64M16HG-AC)
FLASH: 16 MB Winbond W25Q128
ETH:
  - 2x 100M LAN (QCA9533 internal AR8229 switch, eth0)
  - 1x 100M WAN (QCA9533 internal PHY, eth1)
WIFI:
  - 2.4GHz: 1x QCA9533 2T2R (b/g/n)
  - 2 external non detachable antennas (near the power barrel side)
LTE:
  - Quectel EC200T-EU (or -CN or -AU depending on markets)
  - 2 external non detachable antennas (near the sim slot side)
BTN:
  - 1x Reset button
LEDS:
  - 5x White leds (Power, Wifi, Wan, Lan1, Lan2)
  - 1x RGB led (Internet)
UART: 115200-8-N-1 (Starting from lan ports in order: GND, RX, TX, VCC)

Everything works correctly.

MAC Addresses
-------------
LAN XX:XX:XX:XX:XX:48 (art@0x1002)
WAN XX:XX:XX:XX:XX:49 (art@0x1002 + 1)
WIFI XX:XX:XX:XX:XX:48

LABEL XX:XX:XX:XX:XX:48

Installation
------------
Turn the router on while pressing the reset button for 4 seconds.
You can simply count the flashes of the first lan led. (See notes)
If done correctly you should see the first lan led glowing slowly and
you should be able to enter the U-Boot web interface.

Click on the second tab ("固件") and select the -factory.bin firmware
then click "Update firmware".

A screen "Update in progress" should appear.

After few minutes the flash should be completed.

This procedure can be used also to recover the router in case of soft
brick.

Backup the original firmware
----------------------------
The following steps are intended for a linux pc. However using the
right software this guide should also work for Windows and MacOS.

1) Install a tftp server on your pc. For example tftpd-hpa.

2) Create two empty files in your tftp folder called:
	kuwfi_c910_all_nor.bin
	kuwfi_c910_firmware_only.bin

3) Give global write permissions to these files:
	chmod 666 kuwfi_c910_all_nor.bin
	chmod 666 kuwfi_c910_firmware_only.bin

4) Start a netcat session on your pc with this command:
	nc -u -p 6666 192.168.1.1 6666

5) Set the static address on your pc: 192.168.1.2. Connect the router
	to your pc.

6) Turn the router on while pressing the reset button for 8-9 seconds.
	You can simply count the flashes of the first lan led. If you
	press the reset button for too many seconds it will continue
	the normal boot, so you have to restart the router. (See notes)

7) If done correctly you should see the U-Boot network console and you
	should see the following lines on the netcat session:
Version and build date:
  U-Boot 1.1.4-55f1bca8-dirty, 2020-05-07

Modification by:
  Piotr Dymacz <piotr@dymacz.pl>
  https://github.com/pepe2k/u-boot_mod

u-boot>

8) Start the transfer of the whole NOR:
	tftpput 0x9f000000 0x1000000 kuwfi_c910_all_nor.bin

9) The router should start the transfer and it should end with a
	message like this (pay attention to the bytes transferred):
TFTP transfer complete!

Bytes transferred: 16777216 (0x1000000)

10) Repeat the same transfer for the firmware:
	tftpput 0x9f050000 0xfa0000 kuwfi_c910_firmware_only.bin

11) The router should start the transfer and it should end with a
	message like this (pay attention to the bytes transferred):
TFTP transfer complete!

Bytes transferred: 16384000 (0xfa0000)

12) Now you have the backup for the whole nor and for the firmware
	partition. If you want to restore the OEM firmware from OpenWrt
	you have to flash the kuwfi_c910_firmware_only.bin from the
	U-Boot web interface.

	WARNING: Don't use the kuwfi_c910_all_nor.bin file. This file
	is only useful if you manage to	hard brick the router or you
	damage the art partition (ask on the forum)

Notes
-----
This router (or at least my unit) has the pepe2k's U-Boot. It's a
modded U-Boot version with a lot of cool features. You can read more
here: https://github.com/pepe2k/u-boot_mod

With this version of U-Boot, pushing the reset button while turning on
the router starts different tools:
 - 3-5 seconds: U-Boot web interface that can be used to replace the
 	firmware, the art or the U-Boot itself
 - 5-7 seconds: U-Boot uart console
 - 7-10 seconds: U-Boot network console
 - 11+ seconds: Normal boot

The LTE modem can be used in cdc_ether (ECM) or RNDIS mode.
The default mode is ECM and in this commit only the ECM software is
included. In order to set RNDIS mode you must use this AT command:
	AT+QCFG="usbnet",3
In order to use again the ECM mode you must use this AT command:
	AT+QCFG="usbnet",1

Look for "Quectel_EC200T_Linux_USB_Driver_User_Guide_V1.0.pdf" for
other AT commands

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-12-17 22:28:10 +01:00
Shiji Yang
6361a952af ramips: improve support for SIM SIMAX1800T and Haier HAR-20S2U1
1. Use ARTIFACTS to build factory image. This change allows users to
   generate initramfs factory image using OpenWrt ImageBuilder.

2. Override the default bootargs property defined in "mt7621.dtsi".
   Although we use the "bootargs-override" property to set bootargs,
   the default "bootargs" property will still be written into the
   device tree, so it is better to override it.

Tested on SIM SIMAX1800T

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-17 21:08:14 +01:00
Shiji Yang
a7d8b54f86 ramips: improve support for H3C TX180x series devices
1. Explicitly declare gpio pin groups to ensure that gpio works properly.

2. Override bootargs in device tree to avoid modifying u-boot envs during
   initial installation.

Tested on H3C TX1801 Plus

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-17 21:08:14 +01:00
Chukun Pan
53123b93b0 sunxi: fix board_name for MarsBoard A10
The compatible in the device tree is "haoyu,a10-marsboard",
modify the board_name to keep it consistent.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-12-17 20:55:47 +01:00
Chukun Pan
7bcf6b54fc sunxi: fix typo in device packages for MarsBoard A10
The kmod prefix for sound-soc-sunxi is missing, fix it.
Also add kmod-sound-core as dependence.

Fixes: 6a35659 ("sunxi: Added profile for HAOYU Electronics Marsboard A10")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-12-17 20:55:47 +01:00
Nick Hainke
af5306ba70 ath79: convert WiFis based on ar7241_ubnt_unifi.dtsi to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

While working on it remove stale uboot partition label and merge art
into partition node.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:48:57 +01:00
Nick Hainke
b7ad3c5c5d ath79: convert Buffalo WZR-HP-G302H A1A0 WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Merge art into partition node.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:48:57 +01:00
Nick Hainke
d4ec4f9d0b ath79: convert OpenMesh OM2P v1 WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Merge art into partition node.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:40:30 +01:00
Nick Hainke
f6ca84bf02 ath79: convert OpenMesh OM5P-AN WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Merge art into partition node.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:40:30 +01:00
Nick Hainke
46077860c2 ath79: convert boards based on ar9344_openmesh_mr600.dtsi to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Merge art into partition node.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:40:29 +01:00
Chuanhong Guo
7fb32285d5
mediatek: redmi-ax6000: drop cs-gpios
'cs-gpios = <0>, <0>' is a hack in ath79 to override the incorrectly
specified maximum number of chipselects available in spi-ath79.c.
It's not needed here and must have been copied here by mistake.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 15:07:54 +08:00
Chen Minqiang
18bea173a6 mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.

1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
   stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
   to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
   be helpful for users who may forget to do this before sysupgrade in
   the initramfs.

New flash instructions:
1. Gain ssh access. Please refer to:
   https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)

2. Check which system current u-boot is loading from:
   COMMAND: `cat /proc/cmdline`
   sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
   if firmware=1, current system is ubi1
   if firmware=0, current system is ubi0

3. Setup nvram and write the firmware:
   If the current system is ubi1, please set it up so that the next time
   it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
   If the current system is ubi, please set it up so that the next time
   it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```

4. After rebooting, the system should now boot into the openwrt initramfs.
   Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.

For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:

1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```

2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 15:04:16 +08:00
Christian Marangi
d7876daf65
generic: add support for EON EN25QX128A spi nor flash
Add support for EON EN25QX128A spi nor flash with no flags as it does
support SFDP parsing.

Fixes: #9442
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ramips/mt7621: xiaomi_mi-router-4a-gigabit]
2022-12-16 20:58:36 +01:00
Furong Xu
d9e1362581 mediatek: add LED support for Xiaomi Redmi AX6000
add DT nodes and default package for the LEDs on Redmi AX6000

Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-16 21:42:02 +08:00
Furong Xu
335c1e7cfd mediatek: enable sel_clk for spi-mt65xx
Without explicitly enabling sel_clk, clk_disable_unused() will disable
it when boot is done, causing CPU hang on SPI1 register access on MT7986.
Explicitly enable sel_clk to make SPI1 functional.

Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-16 21:42:02 +08:00
INAGAKI Hiroshi
88db7461cf realtek: add Linux Kernel 5.15 as testing version
Add Linux Kernel 5.15 support for testing.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[APRESIA ApresiaLightGS120GT-SS, Panasonic Switch-M24eG PN28240K, Switch-M48eG PN28480K]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
TP-Link TL-SG2008P
Tested-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[D-Link DGS-1210-20, DGS-1210-52, Zyxel XGS1010-12]
Tested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[Zyxel XGS1250-12]
Tested-by: Lucian Cristian <lucian.cristian@gmail.com> # Zyxel
[HPE 1920-8G, 1920-48G]
Tested-by: Jan Hoffmann <jan@3e8.eu>
2022-12-15 20:54:12 +01:00
INAGAKI Hiroshi
69055a5412 realtek: enable needs_standalone_vlan_filtering on DSA driver in 5.15
To configure VLAN 0, enable needs_standalone_vlan_filtering option
of dsa_switch struct.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:54:03 +01:00
INAGAKI Hiroshi
109962d8bf realtek: update dsa.c of DSA driver for 5.15
- rtl83xx_vlan_filtering()

  "struct switchdev_trans *trans" parameter was removed[1] and
  "struct netlink_ext_ack *extack" was added[2].

[1]: https://www.spinics.net/lists/netdev/msg712250.html
[2]: https://www.spinics.net/lists/netdev/msg722496.html

- rtl83xx_vlan_add/del()

  vlan->vid_begin and vlan->vid_end were removed and vlan->vid was
  added[3].

[3]: https://www.spinics.net/lists/netdev/msg712248.html

- rtl83xx_vlan_prepare()

  "port_vlan_prepare" member was removed from "dsa_switch_ops" struct
  in dsa.h[4] and vlan_prepare function should be called from vlan_add
  function. Also, change return type of vlan_add function to int.

[4]: https://www.spinics.net/lists/netdev/msg712252.html

- rtl83xx_port_mdb_add()

  "port_mdb_prepare" member in "dsa_switch_ops" struct was removed and
  preparation need to be done in the function of "port_mdb_add" member
  instead. And also, int type need to be returned on "port_mdb_add"
  member[5].

[5]: https://www.spinics.net/lists/netdev/msg712251.html

- rtl83xx_port_pre_bridge_flags(), rtl83xx_port_bridge_flags()

  The current "port_pre_bridge_flags" member and "port_bridge_flags"
  member in "dsa_switch_ops" in dsa.h has flags of
  "struct switchdev_brport_flags" type instead[6], so adjust to it.
  And, the changed features are passed by flags.mask[7] in
  rtl83xx_port_bridge_flags(), so check it before calling function
  to enable/disable fieature.

[6]: https://lore.kernel.org/lkml/20210212151600.3357121-7-olteanv@gmail.com/
[7]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e18f4c18ab5b0dd47caaf8377c2e36d66f632a8c

Suggested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[shorten final return statement of rtl83xx_port_mdb_add()]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
1f153558a3 realtek: update platform support for 5.15
- fw_passed_dtb and others were replaced to get_fdt() function[1]
- __appended_dtb defined by asm/bootinfo.h[2]

[1]: https://www.spinics.net/lists/linux-mips/msg03332.html
[2]: https://www.spinics.net/lists/linux-mips/msg03332.html

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
f3a9975549 realtek: refresh config-5.15 in all subtargets
Refresh config-5.15 in all subtargets by kernel_menuconfig.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
aa528eec73 realtek: refresh patches in 5.15
Adjust patches for kernel 5.15.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
23881c91e5 realtek: drop patches of upstreamed fix and changes from 5.15
- 007-5.16-gpio-realtek...: upstreamed on 5.16 and backported to 5.15.3
- 708-brflood-spi.patch   : upstreamed
- 709-lag-offloading.patch: upstreamed
- 713-v5.12-net-dsa-...   : upstreamed and some implementations are
                            replaced

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
a9d5a8bc79 realtek: drop patches of upstreamed drivers from 5.15
The following drivers were upstreamed and available on 5.15, so drop
from OpenWrt tree.

- realtek-otto-gpio (5.13)
- realtek-rtl-spi (5.12)
- realtek-rtl-intc (5.12)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
8fb15ea52a realtek: copy dts/files/patches/configs for 5.15
Copy dts/files/patches/configs from 5.10 to 5.15.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[refresh with updated DGS-1210 dts files]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-15 20:52:09 +01:00
Christian Lamparter
d8da5002a2 ath79: fix dtc warnings in ruckus zf7372
|:69.4-14: Warning (reg_format): beamforming-2g-gpio@0:reg: property has invalid length (4 bytes)
|:85.4-14: Warning (reg_format): beamforming-5g-gpio@0:reg: property has invalid length (4 bytes)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Christian Lamparter
0dacf14495 ath79: fix dtc warnings in eap1750h
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)

also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Christian Lamparter
0f227720f9 ath79: fix dtc warnings in eap1200h
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)

also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
4146701469 ath79: replace reference to legacy qca,disable-2ghz in WatchGuard AP100
Commit 4c8dd973ef ("ath9k: OF: qca,disable-(2|5)ghz => ieee80211-freq-limit")
removed "qca,disable-5ghz" and "qca,disable-2ghz".

Signed-off-by: Nick Hainke <vincent@systemli.org>
(converted patch to remove the ieee80211-freq-limit property instead)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
ae5cb164cd ath79: switch to upstream ieee80211-freq-limit for Araknis AN-300-AP-I-N
Commit 4c8dd973ef ("ath9k: OF: qca,disable-(2|5)ghz => ieee80211-freq-limit")
removed "qca,disable-5ghz" and "qca,disable-2ghz". Switch to upstream
ieee80211-freq-limit.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-15 15:45:47 +01:00
Nick Hainke
08c114ee16 ath79: convert Winchannel WB2000 WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
(removed mtd-cal-data property, merged art + addr nodes back into
partition)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
fd456106aa ath79: convert Ubiquiti UniFi AP Pro WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
f63cf33aa7 ath79: convert OCEDO Raccoon WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art into partition node, removed stale uboot label)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
783936c1f7 ath79: Mercury MW4530R v1 already uses nvmem-cells
Remove the caldata extraction in userspace. The board already uses
nvmem-cells since
commit e354b01baf ("ath79: calibrate all ar9344 tl-WDRxxxx with nvmem")

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-15 15:45:35 +01:00
Nick Hainke
4845b60525 ath79: convert boards based on senao_ap-dual.dtsi WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-15 15:08:09 +01:00
Nick Hainke
21495c92dc ath79: convert Atheros DB120 WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art-node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:08:09 +01:00
Nick Hainke
1b125aabf4 ath79: convert Araknis AN-300-AP-I-N WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-15 15:08:08 +01:00
Johannes Heimansberg
708ea56fb9 bcm27xx: bcm2711: add kmod-r8169
Some carrier boards [1][2] for the Raspberry Pi CM4 that are specifically
designed to be used as routers come with secondary NICs using a Realtek
RTL8111 Gigabit Ethernet chip.

When using such a board as a router with OpenWrt, it is very helpful
when both NICs are working by default. Since the Raspberry Pi 4 and the
CM4 have plenty of disk space, it should cause no harm to include the
kmod-r8169.

[1] https://wiki.dfrobot.com/Compute_Module_4_IoT_Router_Board_Mini_SKU_DFR0767
[2] https://www.waveshare.com/wiki/CM4-DUAL-ETH-MINI

Signed-off-by: Johannes Heimansberg <git@jhe.dedyn.io>
(r8169 should pull in the necessary dependencies.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:08:08 +01:00
Linus Walleij
1bef8d62d4 bcm53xx: Patch to support BCMA rev 11
A backported patch to the BCMA driver necessary to support the
DWL-8610AP and DIR-890L. Patch will be in upstream v6.2.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-12-15 15:08:08 +01:00
John Audia
90120a1552 kernel: bump 5.10 to 5.10.159
Removed upstreamed:
	backport-5.10/888-v6.1-ca8210-Fix-crash-by-zero-initializing-data.patch[1]

All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.159&id=0a8e66e375736ea12c11f0ef238ba2a8efec460b

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-14 23:37:28 +01:00
John Audia
b6fa423907 kernel: bump 5.15 to 5.15.83
Removed upstreamed:
	backport-5.15/883-v6.1-ca8210-Fix-crash-by-zero-initializing-data.patch[1]

All patches automatically rebased

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.83&id=246bcd05ba6cc43b34ac0bb4bac3ea94a4efa07c

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-14 23:34:50 +01:00
Stijn Tintel
b3dd15ca0a kernel: add missing symbol to 5.10 config
Kernel 5.10.158 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.

Fixes: 6801c460b6 ("kernel: bump 5.10 to 5.10.158")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-14 20:29:36 +02:00
Stijn Tintel
f9bd655f16 kernel: add missing symbol to 5.15 config
Kernel 5.15.82 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.

Fixes: 68426e54ed ("kernel: bump 5.15 to 5.15.82")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-14 19:12:33 +02:00
Stijn Tintel
230f2fccd1 qoriq: switch to kernel 5.15
The testing kernel has been running fine for months on a rather complex
network setup, with one exception being a crash in
__xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so
let's switch the qoriq target to kernel 5.15 by default.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-14 18:53:39 +02:00
Christian Marangi
823ddab80e
ipq806x: 5.15: standardize wpq864 partition table
Compex WPQ864 contains a non standard partition table. Each partition
node should be named partition and should contain a valid reg.
Fix an extra "-" present after the reg for SBL2_1 partition.

Also add "0:" to each qcom default partition following smem naming.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-14 02:23:22 +01:00
Christian Marangi
266b261d39
ipq806x: 5.15: fix wrong boot-partitions values for split partitions
The refreshed patch actually use the format of <start size start size>
instead of <start end start end>. This cause boot fail since the rootfs
can't be mounted with these wrong values.

Fix it to the correct format in each affected dts.

Fixes: #11498
Fixes: 6134ba4a34 ("ipq806x: 5.15: add boot-partitions binding to fix block warning")
Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-14 02:23:22 +01:00
Andrew Cameron
550e5b2184 ath79: add support for TP-Link CPE605-v1
TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - 560/450/225 MHz (CPU/DDR/AHB)
 - 1x 10/100 Mbps Ethernet
 - 64 MB of DDR2 RAM
 - 8 MB of SPI-NOR Flash
 - 23dBi high-gain directional antenna and a dedicated metal reflector
 - Power, LAN, WLAN5G green LEDs
 - 3x green RSSI LEDs

Flashing instructions:
 Flash factory image through stock firmware WEB UI or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2022-12-13 23:17:27 +01:00
Mikhail Zhilkin
0ec8d991c2 ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1.  Login to the router web interface under admin account
2.  Navigate to Settings -> Configuration -> Save to Computer
3.  Decode the configuration. For example, using cfgtool.py tool (see
    related section):
       cfgtool.py -u configurationBackup.cfg
4.  Open configurationBackup.xml and find the following line:
    <PARAMETER name="Password" type="string" value="<your router serial \
       is here>" writable="1" encryption="1" password="1"/>
5.  Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6.  Encode the configuration. For example, using cfgtool.py tool:
       cfgtool.py -p configurationBackup.xml
7.  Upload the changed configuration (configurationBackup_changed.cfg) to
    the router
8.  Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
    ETxxxxxxxxxx is the serial number from the backplate label)
9.  Navigate to Settings -> WAN -> Add static IP interface (e.g.
    10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
    10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
    ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
       sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
       printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
       reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
      cd /tmp
      for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
      tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
      tftp -l mtd.md5 -p 10.0.0.2

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | *:50    |
| WAN | label + 11 | *:5b    |
| 2g  | label + 2  | *:52    |
| 5g  | label + 3  | *:53    |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000

cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker

Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-12-13 23:06:20 +01:00
Christian Marangi
05dbdcbd32
generic: move pending 870 ca8210 fix crash patch to backport
Patch got merged upstream in kernel 6.1. Move it to backport to better
track it.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-13 02:05:29 +01:00
Christian Marangi
c3c9ef598c
generic: fix wrong PTR_ERR use in of net mac address ascii patch
nvmem_cell_read return a pointer error when an error occurs. Currently
we convert the pointer error to an int while the rest of the function
return a void* and expcet an error pointer. Fix this PTR_ERR msuse
fixing compilation warning.

Fixes the following compilation warning:
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address':
net/ethernet/eth.c:547:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
  547 |                 return PTR_ERR(mac);
      |                        ^~~~~~~~~~~~
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address_ascii':
net/ethernet/eth.c:564:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
  564 |                 return PTR_ERR(mac_ascii);
      |                        ^~~~~~~~~~~~~~~~~~

Fixes: 7b863af180 ("kernel: move mac-address-ascii patches to generic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-13 00:33:19 +01:00
Linus Walleij
772434e707 gemini: Set proper default networks
Some Gemini devices are NAS type devices and need to ask for
DHCP IP on eth0. Some has a LAN/WAN setup. Add sensible
defaults for all known devices.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-12-12 11:18:02 +01:00
Christian Lamparter
50d20db6a8 uml: switch to Kernel 5.15
Switch over from testing version.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Christian Lamparter
f6c61571fb bcm53xx: remove MR32's openwrt specific patch for LEDs
The patch managed to sneak into v5.15 whereas it was
properly deleted for v5.10.

Fixes: 8f6e2bb178 ("bcm53xx: remove MR32's specific get_leds_dt code")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Chukun Pan
b40a047f1f sunxi: fix sunxi-ir kconfig and description
Removed a20 in description, since it
only works for a10, a13 and a31.
Also refreshed kernel config.

Fixes: #10466
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(moved fixes, refreshed, added CONFIG_DVB_USB=n)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Chukun Pan
a125d46a28 sunxi: modules: remove useless AddDepends/rtc
AddDepends/rtc has been removed in commit 3da7fe6, same here.
Fixes: 3da7fe6 ("kernel: remove useless AddDepends/rtc abstraction")

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(RTC_SUPPORT - though this is implied by the TARGET_sunxi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Tony Butler
1e240f60a5 kernel: modules/lib-lz4: add lz4hc_compress
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config

this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor

Signed-off-by: Tony Butler <spudz76@gmail.com>
2022-12-11 09:32:53 -08:00
Tony Butler
9a1ab8aa03 lantiq: vr9: include usb driver for fritz 7430
Reported by user: missing driver for USB; add to image definition
https://github.com/openwrt/openwrt/issues/11326

Resolves: #11326

Signed-off-by: Tony Butler <spudz76@gmail.com>
Acked-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-12-11 16:46:34 +01:00
Hauke Mehrtens
2484f0951c kernel: Refresh kernel 5.10
Make the patches apply cleanly again.

Fixes: 8327e0fb72 ("kernel: backport the dev_set_threaded export to 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-11 16:42:16 +01:00
Weiping Yang
1c169d28ff ipq40xx: fix usb driver not loaded for GL-A1300
This patch enables USB support for the GL.iNet GL-A1300
Repair the usb driver startup phase is not loaded

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2022-12-11 03:06:54 +01:00
John Audia
6801c460b6 kernel: bump 5.10 to 5.10.158
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00
John Audia
7b7d8fe60d kernel: bump 5.10 to 5.10.157
Manually rebased:
	backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch
	hack-5.10/645-netfilter-connmark-introduce-set-dscpmark.patch

Removed upstreamed:
	pending-5.10/706-netfilter-nf_flow_table-add-missing-locking.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.157&id=b8e494240e69f91517256adcd6fda62d0671772d

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00
John Audia
f83a8329a3 kernel: add symbol in generic config for 5.10.157
Add CONFIG_INET_TABLE_PERTURB_ORDER=16 to generic config

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00
John Audia
68426e54ed kernel: bump 5.15 to 5.15.82
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:42:52 +01:00
John Audia
424210b7be kernel: bump 5.15 to 5.15.81
Manually rebased:
	backport-5.15/715-v6.0-net-ethernet-mtk_eth_soc-add-the-capability-to-run-m.patch
	hack-5.15/645-netfilter-connmark-introduce-set-dscpmark.patch[1]

Removed upstreamed:
	pending-5.15/701-netfilter-nf_flow_table-add-missing-locking.patch[2]

All other patches automatically rebased

1. Rebase by Kevin 'ldir' Darbyshire-Bryant<ldir@darbyshire-bryant.me.uk>
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.81&id=8db9e60cdfdae5b049e32e82323da8f0f989066a

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:42:52 +01:00
John Audia
2b375b7db4 kernel: add symbol in generic config for 5.15.81
Add CONFIG_INET_TABLE_PERTURB_ORDER=16 to generic config

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:42:52 +01:00
Felix Fietkau
8327e0fb72 kernel: backport the dev_set_threaded export to 5.10
Fixes mt76 build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-10 17:36:12 +01:00
Felix Fietkau
5f2d471279 kernel: backport mtk_wed.h from 5.15 to 5.10
Fixes mt76 build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-10 17:30:36 +01:00
David Bauer
4c0919839d ath79: fix Teltonika RUT230 v1 MAC assignment
The MAC-Address setup for the Teltonika RUT230 v1 was swapped for the
LAN / WAN ports. Also the Label-MAC was assigned incorrect, as the WiFi
MAC is printed on the case as part of the SSID, however only the LAN
MAC-Address is designated as a MAC-Address.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-12-09 01:59:47 +01:00
Jan-Niklas Burfeind
dbc93d280c realtek: update GPIO bindings for DGS-1210-10P
add three missing LEDs
 - PoE-Max
 - Link/Act
 - PoE

add two missing buttons
 - mode
 - reset

The last was dropped in
commit 61a3d0075b ("realtek: update GPIO bindings in the dts files in dts-5.10")

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-12-09 00:13:51 +01:00
Andreas Böhler
3e7e4d0b97 realtek: d-link: add support for dgs-1210-28mp-f
General hardware info:
----------------------

D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz,
DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable
with a total PoE power budget of 370W.

Power over Ethernet:
--------------------

The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU.
In order to enable PoE, the realtek-poe package is required. It is
installed by default, but currently it requires the manual editing of
/etc/config/poe. Keep in mind that the port number assignment does not
match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and
24-17.

LEDs and Buttons:
-----------------

On stock firmware, the mode button is supposed to switch the LED indicators
of all port LEDs between Link Activity and PoE status. The currently
selected mode is visualized using the respective LEDs. PoE Max indicates
that the maximum PoE budget has been reached.
Since there is currently no support for this behavior, these LEDs and
the mode button can be used independently.

Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.

Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd

OEM installation from Web Interface:
------------------------------------

  1. Make sure you are booting using OEM in image 2 slot. If not, switch to
     image2 using the menus
        System > Firmware Information > Boot from image2
        Tools > reboot
  2. Upload image in vendor firmware via Tools > Backup / Upgrade
     Firmware > image1
  3. Toogle startup image via System > Firmware Information > Boot from
     image1
  4. Tools > reboot

Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:

Boot initramfs image from U-Boot:
---------------------------------

  1. Press Escape key during `Hit Esc key to stop autoboot` prompt
  2. Press CTRL+C keys to get into real U-Boot prompt
  3. Init network with `rtk network on` command
  4. Load image with `tftpboot 0x8f000000
     openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin`
     command
  5. Boot the image with `bootm` command

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-12-08 21:51:43 +01:00
Jan-Niklas Burfeind
dce66899bf ramips: add support for Wavlink WS-WN572HP3 4G
Wavlink WS-WN572HP3 4G is an 802.11ac
dual-band outdoor router with LTE support.

Specifications;
* Soc: MT7621DAT
* RAM: 128MiB
* Flash: NOR 16MiB GD-25Q128ESIG3
* Wi-Fi:
  * MT7613BEN: 5GHz
  * MT7603EN: 2.4GHz
* Ethernet: 2x 1GbE
* USB: None - only used internally
* LTE Modem: Quectel EC200T-EU
* UART: 115200 baud
* LEDs:
  * 7 blue at the front
    * 1 Power
    * 2 LAN / WAN
    * 1 Status
    * 3 RSSI (annotated 4G)
  * 1 green at the bottom (4G LED)
* Buttons: 1 reset button

Installation:
* press and hold the reset button while powering on the device
* keep it pressed for ten seconds
* connect to 192.168.10.1 via webbrowser (chromium/chrome works, at
  least Firefox 106.0.3 does not)
* upload the sysupgrade image, confirm the checksum, wait 2 minutes
  until the device reboots

Revert to stock firmware:
* same as installation but use the recovery image for WL-WN572HP3

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-12-07 12:30:45 +01:00
David Bauer
bc14925f3d ramips: define loadaddr for all UniFi devices
Define the load-address for the DTB of all Ubiquiti UniFi devices using
FIT images. From the GPL code we can assume these boards are affected by
the same relocating issue with the vendor bootloader.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-12-07 12:30:29 +01:00
Daniel Golle
2307b049e4
mediatek: also move &slot0 from dtsi down to board dts
As the referenced MTD partition is only present in the dts, also move
&slot0 down to the dts files.

Fixes: 64e9b62829 ("mediatek: remove redundant flash entry from dtsi")
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-07 01:45:14 +00:00
Daniel Golle
9d22ab703f mediatek: remove redundant flash entry from dtsi
Splitting-off the common parts of Ruijie RG-EW3200GX PRO and
reyee AX3200-E5 went wrong because the flash descriptiom was kept
also in the dtsi. Remove it there, as flash definition is added by
both board dts files.

Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-07 00:46:26 +00:00
Shiji Yang
3c1512a25d ath79: optimize the firmware recipe for Netgear NAND devices
1. Drop useless character '0xff' before fake filesystem header.
2. Reduce useless padding to shrink the size of the sysupgrade image.
3. Do not check the size of sysupgrade image. It does not make sense to
   check the size of a compressed package.
4. Do not take the size of netgear header into account because it will
   not be written to Flash.
5. Use the default lzma compression dictionary parameter '-d24' to get
   better performance.

Tested on Netgear R6100
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-06 23:11:23 +01:00
Shiji Yang
58088ff457 ath79: convert Netgear R6100 radio calibration to nvmem-cells
use nvmem-cells implementation to avoid copying art calibration data
to rootfs.

Tested on Netgear R6100
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-06 23:11:23 +01:00
Hauke Mehrtens
48025b8ac9 kernel: ca8210: Fix crash by zero initializing data
This fixes crashes at bootup on pistachio.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-06 23:09:48 +01:00
Alex Hansen
7dbac3433f mediatek: add support for reyee AX3200-E5
This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly
different flash layout, install process is the same.

Specifications:
SoC: MT7622B
RAM: 256MB
Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
Ethernet: 5x1GbE
Switch: MT7531BE
WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
2Keys: Mesh button + Reset button
UART: Marked J19 on board. 3.3v, 115200n1
Power: 12V 2.5A

Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
    dd if=/dev/mtd7 of=/tmp/firmware.bin
    and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.

Recovery stock firmware:

1. Transfer the firmware.bin image to the device.
2. Flash the image with:
    mtd write firmware.bin firmware

Signed-off-by: Alex Hansen <mralexh123@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-06 12:43:15 +00:00
Joonhyuk Song
25ede5170d ramips: mt7621: enable lzma-loader for netis WF2881
Fixes boot loader LZMA decompression issues (LZMA ERROR 1)

Signed-off-by: Joonhyuk Song <thenoface303@gmail.com>
2022-12-06 01:51:00 +01:00
John Thomson
7ea965b578 ramips: mt7621: mikrotik 760igs (hEX S) fix SFP
This device uses an AR8031/AR8033 chip to convert SoC gmac1
RGMII to 1000base-x or sgmii for the SFP fibre cage.
The SFP cage requires phy-mode rgmii-rxid, and without it will not
recieve any packets: ethtool -S sfp rx_fcs_errors will increase when
packets should be being received, but no other _rx counters will change.

Fixes: c77858aa79 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2022-12-06 01:47:36 +01:00
Daniel Golle
83f20fc9f7 mediatek: mt7623: build mt6577_auxadc driver into kernel
Set CONFIG_MT6577_AUXADC=y as otherwise reading temperature of the
thermal-zone doesn't work on MT7623 (it does work fine without this
driver on MT7622 and MT7986).

Fixes: f2ae4e2f8c ("mediatek: clean up platform kernel modules")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-05 23:14:36 +00:00
INAGAKI Hiroshi
a224412bbc ramips: use ARTIFACTS for initramfs-factory of I-O DATA WN-AX1167GR
Use ARTIFACTS to generate initramfs-based factory image of I-O DATA
WN-AX1167GR instead of redundant recipe which generate on
KERNEL_INITRAMFS.

Note:

WN-AX1167GR has 2x OS images on stock firmware.

stock log:

flash manufacture id: c2, device id 20 18
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"

1st image is "Kernel" and 2nd is "app" when booted from 1st image.
In OpenWrt, those 2x partitions are combined to "firmware" with
undefined (empty) areas (0x7e0000-0x7fffff, 0xf80000-0xf8ffff).

The size of an OS image partition is 0x780000 (7680 KiB = 7.5 MiB), so
check-size for initramfs-factory image needs to be called with the size.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-05 01:28:28 +00:00
Senis John
a8f3c97ce8 ramips: add support for HiWiFi HC5611
CPU: MediaTek MT7628AN @ 575 MHz
Flash: 16 MB
RAM: 128 MB
Ethernet: 10/100Mbps x 1
Wlan: 300 Mbps
USB: USB 2.0 x 1
LED: red/green x 1
Button: reset x 1

1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh
2. Upload the openwrt firmware to the router via SCP
3. Login the router via SSH
4. Run `mtd -r write path_to_firmware.bin firmware`

I have tested on my device.
- The LED will display RED on power-on, After system start completed, trun GREEN
- Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device
- USB can working under official u-boot

Signed-off-by: Senis John <thank243@gmail.com>
2022-12-04 15:21:12 +08:00
Kien Truong
d11d93b9ae rockchip: enable watchdog driver
Enable Synopsys DesignWare watchdog driver for rockchip device

Tested on NanoPi R2S

Signed-off-by: Kien Truong <duckientruong@gmail.com>
2022-12-04 15:21:12 +08:00
Petr Štetiar
97c77fff28 Revert "mvebu: switch default kernel to 5.15"
This reverts commit 5429411f73 as upstream
in commit e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies") has
changed `PTP_1588_CLOCK` dependency handling in 5.15 kernel.

That currently leads to `CONFIG_NET_DSA_MV88E6XXX=m` in images produced
by buildbots due to `CONFIG_ALL_KMODS=y` config option being used in
those builds, which leads to a broken LAN bridge network on several
devices.

References: https://lists.infradead.org/pipermail/openwrt-devel/2022-December/039950.html
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-12-04 08:16:49 +01:00
Bjørn Mork
8719f73fa2 ramips: mt7621: enable lzma-loader for ZyXEL WAP6805
Fixing "Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board
to recover".

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2022-12-03 21:04:38 +01:00
Stijn Segers
5429411f73 mvebu: switch default kernel to 5.15
In light of https://github.com/openwrt/openwrt/issues/11077, switch mvebu
to 5.15 which has been the testing kernel on this target since April - over
half a year.

Run-tested on the following subtargets:
* cortexa9 (Turris Omnia - 03f41b1eb2)
* cortexa72 (MikroTik RB5009UG+S+IN)

Tested-by: Enrico Mioso <mrkiko.rs@gmail.com> [GL-MV1000]
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2022-12-02 16:57:48 +01:00
Jan-Niklas Burfeind
a5873ad675 realtek: fix dell typo
should be add/delete or abbreviated add/del

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
2022-12-01 22:49:23 +01:00
Luiz Angelo Daros de Luca
ed9bd9824a realtek: refactor keep vlan tag setup, fix tagged forwarding
The code in dsa.c:rtl83xx_port_enable() was trying to set
vlan_port_tag_sts_ctrl while dealing with differences between SoCs.
However, not only that register has a different address, the register
structure and even the 2-bit value semantic changes for each SoC.

The vlan_port_tag_sts_ctrl field was dropped and converted into a
vlan_port_keep_incoming_tag_set() function that abstracts the different
between SoCs. The macro referencing that register migrated to the SoC
specific c file as it will be privately used by each file.

All magic numbers were converted into macros using BITMASK and
FIELD_PREP.

The vlan_port_tag_sts_ctrl debugfs was dropped for now as it is already
broken for rtl93xx. The best place for SoC specific code might be in each
respective c file and not in if/else clauses.

The final result is:

rtl838x: set ITAG_STS=TAGGED, same as before
rtl839x: set ITAG_STS=TAGGED instead of IGR_P_ITAG_KEEP=0x1, fixing
	 forwarding of tagged packets
rtl930x: set EGR_ITAG_STS=TAGGED instead of IGR_P_ITAG=0x1, possibly
	 fixing forwarding of tagged packets
rtl931x: set EGR_ITAG_STS=TAGGED instead of OTPID_KEEP=0x1, possibly
         fixing forwarding of tagged packets

Without (EGR_)ITAG_STS=TAGGED, at least for rtl839x, forwarded packets
will drop the vlan tag while packets from the CPU will still have the
correct tag.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2022-12-01 22:15:55 +01:00
Olliver Schinagl
59542c9ac9 realtek: Fix rtl930x speed status accessor
The rtl930x speed status registers require 4 bits to indicate the speed
status. As such, we want to divide by 8. To make things consistent with
the rest of this code, use a bitshift however.

This bug probably won't affect many users yet, as there aren't many
rtl930x switches in the wild yet with more then 10 ports, and thus a
low-impact bugfix.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[also fix port field extraction]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-01 22:11:06 +01:00
Alexander Couzens
d4c460648d
ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6
The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP
with a miniPCIe slot for a LTE modem.
The wAP R AC is similar to the wAP AC but with the miniPCIe slot.
The wAP R AC requires installing a LTE modem.
The wAP LTE and wAP LTE6 comes with a LTE modem installed.

See https://mikrotik.com/product/wap_r_ac for more info.

Specifications:
- SoC: Qualcomm Atheros IPQ4018
- CPU: 4x ARM Cortex A7
- RAM: 128MB
- Storage: 16MB NOR flash
- Wireless:
   - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna
   - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports
  one with 802.3af/at PoE in
- 1x Mini PCI-E port (USB2)

Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2022-11-27 13:28:22 +00:00
Aleksander Jan Bajkowski
bb2fb4f16a airoha: disable swconfig
Swconfig isn't used by this target and can be disabled for
this reason. Airoha doesn't even have an Ethernet driver.
In the future, this target should get a DSA driver.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-27 13:18:29 +01:00
Aleksander Jan Bajkowski
d81e948dc2 airoha: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=platform

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
5b0e111789 layerscape: kmod-ppfe: Use ppfe driver as module
In 8274451cb86 kmod-ppfe was changed to built-in because CONFIG_FSL_PPFE
was binary. In 5.10 and 5.15 kernel, PPFE driver can be build as module.

This patch switch kmod-ppfe from build-in to loadable module.
Loadable module helps to avoid hazard: driver is looking for firmware
file before mount root.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
23b9b01cdd layerscape: switch kernel testing to 5.15
Let's test layerscape with 5.15 kernel.

Run tested: LS1012A-FRDM, LS1046A-RDB (nor and sd-boot images),
	    LS1021A-IOT (By @ArtelMike with u-boot fix)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
afcccaad82 layerscape: Switch LS1012A-FRDM initramfs to gzip
At this moment LS1012A-FRDM have uncompressed initramfs image.

Error was caused, because gzip extract area overlap image.

Let's change loadaddr and enable gzip initramfs images again.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
d64d1c86cc layerscape: remove kernel 5.4 dependences
5.4 kernel was removed. Let's clean old dependences.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
a42edce9fd layerscape: 5.15: refresh kernel config
Done by 'make kernel_oldconfig'.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
8efffce677 layerscape: copy patches 5.10 to 5.15
One patch manually rebased:
302-arm64-dts-ls1012a-update-with-ppfe-support.patch

PFE driver patch recreated from NXP 5.15 tree:
701-staging-add-fsl_ppfe-driver.patch

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
f620fb4b73 layerscape: copy config 5.10 to 5.15
Configs was just copied.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
2268d55521 layerscape: refresh kernel config
Done by 'make kernel_oldconfig'.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
2e4fe289ce layerscape: Fix SPI-NOR issues with vendor patches
For some reason LS1012A and LS1046A devboards don't work well with
Spansion SPI NOR flash. It cause read and write errors like:

[   27.285887] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x025ae000
[   27.468922] jffs2: Newly-erased block contained word 0x0 at offset 0x02573000
[   27.502615] jffs2: Newly-erased block contained word 0xe723f41e5823f110 at offset 0x02572000
[   27.541550] jffs2: Newly-erased block contained word 0x1a7d266ee6 at offset 0x02571000
[   27.577195] jffs2: Newly-erased block contained word 0x5d000bae8d52fec6 at offset 0x02570000
[   27.611800] jffs2: Newly-erased block contained word 0x63515aee63515a4b at offset 0x0256f000
[   27.651749] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0256e000
[   27.825593] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0252e000

NXP have found workarround and applied in their vendor kernel version.
They force 1x tx and 1x rx lines in qspi. That method fix issues.
This patch ports patches from NXP LSDK tree.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Will Moss
a58146d452 ath79: D-Link DIR-825 B1 add factory.bin recipe
- Bring back factory.bin image which was missing after porting device to ath79 target
- Use default sysupgrade.bin image recipe
- Adjust max image size according to new firmware partition size after
"ath79: expand rootfs for DIR-825-B1 with unused space (aca8bb5)" changes
- Remove support of upgrading from version 19.07, because partition size changes mentioned above

Signed-off-by: Will Moss <willormos@gmail.com>
2022-11-27 13:18:29 +01:00
Michael Pratt
6de9287abd ath79: add support for Senao Engenius EAP1750H
FCC ID: A8J-EAP1750H

Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9558 SOC
  - QCA9880 WLAN	PCI card, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM	NT5TU32M16FG
  - UART at J10		populated
  - 4 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)

**MAC addresses:**

  MAC addresses are labeled as ETH, 2.4G, and 5GHz
  Only one Vendor MAC address in flash

  eth0 ETH  *:fb art 0x0
  phy1 2.4G *:fc ---
  phy0 5GHz *:fd ---

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin at J10

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs to 'vmlinux-art-ramdisk'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

  NOTE: TFTP is not reliable due to bugged bootloader
  set MTU to 600 and try many times
  if your TFTP server supports setting block size
  higher block size is better.

**Format of OEM firmware image:**

  The OEM software of EAP1750H is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
    openwrt-ar71xx-generic-eap1750h-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-11-27 13:18:29 +01:00
Michael Pratt
128947db42 ath79: use nvmem-cells for radio calibration of EAP1200H
Transition from userscript to DTS for all of ART.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-11-27 13:18:29 +01:00
Edward Chow
2c33fd39a5 ath79: calibrate TP-LINK TL-WR2543ND with nvmem
Driver for and pci wlan card now pull the calibration data from the nvmem
subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my tplink tl-wr2543nd.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-27 13:18:29 +01:00
John Audia
acb10faa35 kernel: bump 5.10 to 5.10.156
Manually rebased: ath79/patches-5.10/910-unaligned_access_hacks.patch

All other patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-27 13:18:29 +01:00
John Audia
590aa0ca51 kernel: bump 5.15 to 5.15.80
Manually rebase:
   pending-5.15/330-MIPS-kexec-Accept-command-line-parameters-from-users.patch
   ath79/patches-5.15/910-unaligned_access_hacks.patch

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-27 13:18:29 +01:00
Christian Marangi
60fc93b359
ipq806x: disable cache and fabric devfreq driver to improve stability
It was tested that cache scaling currently cause instability problem.
This is probably caused by a latent misconfiguration that cause the L2
cache to be sourced from the wrong source and runs at an unstable freq
compared to the original QSDK fw.

To improve stability while the problem is bisected, disable the devfreq
drivers with minimal perf penality.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-11-26 00:38:31 +01:00
Felix Fietkau
3dff6b53db kernel: fix mtk_eth_soc issue when using secondary GMAC on MT7621/MT7622
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break

Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-25 01:56:53 +01:00
Daniel Golle
c1d1202e67
mediatek: set persistent wifi mac for bpi-r64 and bpi-r3
Use persistent MAC address for the built-in wireless interfaces of the
BPi-R64 and BPi-R3 development boards.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:33 +00:00
Daniel Golle
87fc485450
ipq40xx: remove '-fit' string from kernel filenames
The type of those images is already distinguishable by the '.itb'
extension, there is no need for an additional '-fit' string in the
filenames. Remove it to behave more like other targets.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:28 +00:00
Daniel Golle
d9f7c751c9
ipq40xx: remove 'nand-' string from image filenames
Only on the ipq40xx subtarget different filenames were used for NAND-
based devices. This is unneeded, confusing and breaks downstream tools
such as luci-app-attendedsysupgrade and auc.
Remove the 'nand-' string from image filenames to fix that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:18 +00:00
Edmunt Pienkowsky
c34eab6fd1 bcm27xx: sound-soc-justboom-*: fix packages
Affected packages: sound-soc-justboom-both, sound-soc-justboom-dac and sound-soc-justboom-digi.

- Add snd-soc-wm8804-i2c and/or snd-soc-pcm512x-i2c kernel modules.
- Add kmod-regmap-i2c package dependency.

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
2022-11-23 20:17:21 +01:00
Edmunt Pienkowsky
0889adf16f bcm27xx: sound-soc-hifiberry-digi: fix package
- Add snd-soc-wm8804-i2c kernel module,
- Add kmod-regmap-i2c package dependency.

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
2022-11-23 20:17:18 +01:00
John Audia
3f7cc9d014 bcm27xx: disable duplicate sdhost driver
Enabling both CONFIG_MMC_BCM2835 and CONFIG_MMC_BCM2835_SDHOST causes this
error in dmesg:
Error: Driver 'sdhost-bcm2835' is already registered, aborting...

Disabling CONFIG_MMC_BCM2835 and leaving CONFIG_MMC_BCM2835_SDHOST enabled
avoids this error.

Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
[Disable driver for all subtargets, refresh configs, tweak description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-23 20:13:46 +01:00
Felix Fietkau
eaba63cdde kernel: fix regression on mt7986
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break

Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-23 11:34:43 +01:00
Felix Fietkau
4e1a6ee903 kernel: add WED rx support for mediatek
This is required for rx flow offloading on mt76 with MT7986 and MT7915

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 20:46:47 +01:00
Felix Fietkau
e410833bdd kernel: add a locking fix for netfilter hardware flow offloading
Protect the flow block cb list readers against concurrent updates

Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 20:44:01 +01:00
Felix Fietkau
9b482ee22f kernel: add more fixes for mtk_eth_soc
Fix corner cases in DSA offload
Add refcounting fix for flow offload
Fix VLAN untagging issue on MT7986

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 11:47:36 +01:00
Maxim Anisimov
21762e4653 ramips: add support for Keenetic KN-3010
Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT.

Specification:
- System-On-Chip: MT7621DAT
- CPU/Speed: 880 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100/1000 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin"
   to "KN-3010_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2022-11-20 16:44:24 +01:00
Xiaopo Zhang
a28297d395 x86: enable PINCTRL for all Intel platform
Enable Intel PINCTRL for all platform on both 32 bit and 64 bit target.

Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
2022-11-20 16:31:10 +01:00
Xiaopo Zhang
34615250a9 x86/64: enable Intel PINCTRL in 64bit target
Intel PINCTRL is not enable in the 64bit build, while it is enabled in
the x86/general target, which disables the ability of controlling GPIO
in the 64 bit build.

This commit copies the corresponding part of x86/general config, since
it is already there, so it should be fine to enable the same settings
here.

Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
2022-11-20 16:31:10 +01:00
Will Moss
288b0004bf ath79: fix MAC address assigment for TP-Link TL-WR740N/TL-WR741ND v4
On TP-Link TL-WR740N/TL-WR741ND v4 LAN MAC address (eth1 in DTS) is main
device MAC address, so do not increment it. WAN MAC is LAN MAC + 1.

Signed-off-by: Will Moss <willormos@gmail.com>
2022-11-20 16:30:27 +01:00
Roger Pueyo Centelles
5a1d7d8c1b ath79: disable image building for Ubiquiti EdgeSwitch 8XP
The downstream OpenWrt driver for the BCM53128 switch ceased to work,
rendering the 8 LAN ports of the device unusable. This commit disables
image building while the problem is being solved.

See issue #10374 for more details.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2022-11-20 16:24:24 +01:00
Edward Chow
3d343ca713 ath79: calibrate nand netgear wndrxxxx with nvmem
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my wndr3700v4 and wndr4500v3.
Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-20 16:13:48 +01:00
Aleksander Jan Bajkowski
bca663f20f kernel: backport tso for asix driver
Performance comparison (iperf3, mtu 1500):
Before: 53.9 Mbps
After: 87.9 Mbps

The tests were performed on a BT Home Hub 5A router.
The iperf3 server was running on the router, the client
on the host.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Christian Buschau
084c20f6c5 lantiq: xway: kernel: enable SMP support
Enabled CONFIG_MIPS_MT_SMP and CONFIG_SCHED_SMT.

Tested on FRITZ!Box 7330 SL, 7312 and o2 Box 4421.

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Christian Buschau
d3527bb83b lantiq: xway: ar9: add ICU1 (2nd core for SMP)
Fixes leftover TODO from commit 6bf179b270

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Christian Buschau
fb0256e88e lantiq: xway: refresh kernel config
Run of 'make kernel_oldconfig CONFIG_TARGET=subtarget'

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Edward Chow
e354b01baf ath79: calibrate all ar9344 tl-WDRxxxx with nvmem
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my tplink tl-wdr4310.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-18 20:27:52 +01:00
Aleksander Jan Bajkowski
224babfd6f mediatek: mt7623: disable swconfig
The mt7623 subtarget supports 2 devices:
 * Bananapi BPi-R2 (added in 1f068588ef, 7762c07c88),
 * UniElec U7623-02 (added in 4def81f30f).

Both devices support DSA from the beginning, thus
swconfig can be safely disabled.

In the past, the subtarget mt7623 also supported
the mt7623 reference board. This board originally
supported swconfig, and was later converted to DSA
(64175ffb79) and then dropped (1ab81bf02d).

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Aleksander Jan Bajkowski
0e001e4185 mediatek: mt7623: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Moritz Warning
dc7d431b60 treewide: uniform vendor name for devolo
The company name is lower case on the website
(https://www.devolo.de) and in product names.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2022-11-18 20:27:52 +01:00
Moritz Warning
c0fb12c42e treewide: uniform vendor name for ASUS
Their own website (https://www.asus.com)
always uses the upper case style name.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2022-11-16 23:30:11 +01:00
Josef Schlehofer
941132cb3c mpc85xx: fix missing kernel config symbol
While compiling OpenWrt master for Turris 1.x routers (p2020), it
reported following error:

    Gianfar Ethernet (GIANFAR) [Y/n/m/?] y
    Freescale DPAA2 Ethernet Switch (FSL_DPAA2_SWITCH) [N/m/y/?] (NEW)
Error in reading or end of file.

Let's fix it by disabling it.

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-11-16 23:30:11 +01:00
John Audia
9e137bb10e kernel: bump 5.10 to 5.10.155
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-16 23:30:11 +01:00
John Audia
170f3d7b0a kernel: bump 5.15 to 5.15.79
All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/mt7621
Run-tested: bcm2711/RPi4B, ramips/mt7621

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-16 23:30:11 +01:00
Kuan-Yi Li
49bbfd9968 cypress-nvram: consolidate NVRAM packages
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-16 20:14:13 +01:00
Kuan-Yi Li
c6e86d8095 linux-firmware: broadcom: consolidate NVRAM packages
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-16 20:14:13 +01:00
Kuan-Yi Li
22fd8b0df6 cypress-nvram: disassociate from external source repo
Since all NVRAM files in external repo are now upstreamed and to lower
future maintenance cost, disassociate the package from external source
repo.

All upstream pending NVRAM files shall be stored locally from now on.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[Remove outdated URL, add SPDX-License-Identifier]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-16 20:14:13 +01:00
Pawel Dembicki
f74275c936 kernel: add missing symbol in generic config
Found during work on qoriq target.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[improve commit message, remove from target configs]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-11-16 20:23:34 +02:00
Kuan-Yi Li
a110418027 linux-firmware: offer two versions of firmware for CYW4339
According to commit 6f6c2fb321, AP6335 module used in PICO-PI-IMX7D works
only with firmware from `linux-firmware`. However, firmware from
`cypress-firmware` suite is directly from the chip company (Infineon) and
is actually newer.

Instead of dropping the firmware from Infineon, create a package named
`brcmfmac-firmware-4339-sdio`, and keep the Infineon version of
`cypress-firmware-4339-sdio` around.

This gives us devs the option to choose. Also, it means that

 - packages `brcmfmac-firmware-*` uniformly come from `linux-firmware`
 - packages `cypress-firmware-*` uniformly come from `cypress-firmware`

so hopefully brings more clarity.

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-15 20:49:58 +01:00
Kuan-Yi Li
729cdff71d bcm27xx: switch to linux-firmware SDIO NVRAM
Package `cypress-nvram` was added because back then the files for newer
RPi models on `linux-firmware` didn't have the proper values.

It is the other way around nowadays, so switch back to `linux-firmware`.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-15 20:48:54 +01:00
Kuan-Yi Li
efaad5e901 cypress-nvram: use symlink to provide NVRAM for some RPis
This is to align the implementation with upstream `linux-firmware`.

Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware`
source repository, their NVRAM is provided through a symbolic link to
NVRAM of another board with an identical wireless design.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-15 20:47:54 +01:00
Chuanhong Guo
c984fc7624
rockchip: use LZMA FIT for kernel image
Use LZMA compressed kernel to save some space in boot partition.

Fixes: #11197
Tested-by: Tianling Shen <cnsztl@immortalwrt.org> [NanoPi R2S]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-11-14 22:50:21 +08:00
Lech Perczak
6fdeb48c1e ath79: support Ruckus ZoneFlex 7025
Ruckus ZoneFlex 7025 is a single 2.4GHz radio 802.11n 1x1 enterprise
access point with built-in Ethernet switch, in an electrical outlet form factor.

Hardware highligts:
- CPU: Atheros AR7240 SoC at 400 MHz
- RAM: 64MB DDR2
- Flash: 16MB SPI-NOR
- Wi-Fi: AR9285 built-in 2.4GHz 1x1 radio
- Ethernet: single Fast Ethernet port inside the electrical enclosure,
  coupled with internal LSA connector for direct wiring,
  four external Fast Ethernet ports on the lower side of the device.
- PoE: 802.3af PD input inside the electrical box.
  802.3af PSE output on the LAN4 port, capable of sourcing
  class 0 or class 2 devices, depending on power supply capacity.
- External 8P8C pass-through connectors on the back and right side of the device
- Standalone 48V power input on the side, through 2/1mm micro DC barrel jack

Serial console: 115200-8-N-1 on internal JP1 header.
Pinout:

---------- JP1
|5|4|3|2|1|
----------

Pin 1 is near the "H1" marking.
1 - RX
2 - n/c
3 - VCC (3.3V)
4 - GND
5 - TX

Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
  adapter, TFTP server,  and removing a single T10 screw,
  but with much less manual steps, and is generally recommended, being
  safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
  work on some rare versions of stock firmware. A more involved, and
  requires installing `mkenvimage` from u-boot-tools package if you
  choose to rebuild your own environment, but can be used without
  disassembly or removal from installation point, if you have the
  credentials.
  If for some reason, size of your sysupgrade image exceeds 13312kB,
  proceed with method [1]. For official images this is not likely to
  happen ever.

[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
   does not back-power the board, otherwise it will fail to boot.

1. Power-on the board. Then quickly connect serial converter to PC and
   hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
   you'll enter U-boot shell. Then skip to point 3.
   Connection parameters are 115200-8-N-1.

2. Allow the board to boot.  Press the reset button, so the board
   reboots into U-boot again and go back to point 1.

3. Set the "bootcmd" variable to disable the dual-boot feature of the
   system and ensure that uImage is loaded. This is critical step, and
   needs to be done only on initial installation.

   > setenv bootcmd "bootm 0x9f040000"
   > saveenv

4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:

   > setenv serverip 192.168.1.2
   > setenv ipaddr 192.168.1.1
   > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7025-initramfs-kernel.bin
   > bootm 0x81000000

5. Optional, but highly recommended: back up contents of "firmware" partition:

   $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7025_fw1_backup.bin

6. Copy over sysupgrade image, and perform actual installation. OpenWrt
   shall boot from flash afterwards:

   $ ssh root@192.168.1.1
   # sysupgrade -n openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin

[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
   it boots, hold the reset button near Ethernet connectors for 5
   seconds.

1. Connect the device to the network. It will acquire address over DHCP,
   so either find its address using list of DHCP leases by looking for
   label MAC address, or try finding it by scanning for SSH port:

   $ nmap 10.42.0.0/24 -p22

   From now on, we assume your computer has address 10.42.0.1 and the device
   has address 10.42.0.254.

2. Set up a TFTP server on your computer. We assume that TFTP server
   root is at /srv/tftp.

3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
   frmware is pretty ancient and requires enabling HMAC-MD5.

   $ ssh 10.42.0.254 \
   -o UserKnownHostsFile=/dev/null \
   -o StrictHostKeyCheking=no \
   -o MACs=hmac-md5

   Login. User is "super", password is "sp-admin".
   Now execute a hidden command:

   Ruckus

   It is case-sensitive. Copy and paste the following string,
   including quotes. There will be no output on the console for that.

   ";/bin/sh;"

   Hit "enter". The AP will respond with:

   grrrr
   OK

   Now execute another hidden command:

   !v54!

   At "What's your chow?" prompt just hit "enter".
   Congratulations, you should now be dropped to Busybox shell with root
   permissions.

4. Optional, but highly recommended: backup the flash contents before
   installation. At your PC ensure the device can write the firmware
   over TFTP:

   $ sudo touch /srv/tftp/ruckus_zf7025_firmware{1,2}.bin
   $ sudo chmod 666 /srv/tftp/ruckus_zf7025_firmware{1,2}.bin

   Locate partitions for primary and secondary firmware image.
   NEVER blindly copy over MTD nodes, because MTD indices change
   depending on the currently active firmware, and all partitions are
   writable!

   # grep rcks_wlan /proc/mtd

   Copy over both images using TFTP, this will be useful in case you'd
   like to return to stock FW in future. Make sure to backup both, as
   OpenWrt uses bot firmwre partitions for storage!

   # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7025_firmware1.bin -p 10.42.0.1
   # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7025_firmware2.bin -p 10.42.0.1

   When the command finishes, copy over the dump to a safe place for
   storage.

   $ cp /srv/tftp/ruckus_zf7025_firmware{1,2}.bin ~/

5. Ensure the system is running from the BACKUP image, i.e. from
   rcks_wlan.bkup partition or "image 2". Otherwise the installation
   WILL fail, and you will need to access mtd0 device to write image
   which risks overwriting the bootloader, and so is not covered here
   and not supported.

   Switching to backup firmware can be achieved by executing a few
   consecutive reboots of the device, or by updating the stock firmware. The
   system will boot from the image it was not running from previously.
   Stock firmware available to update was conveniently dumped in point 4 :-)

6. Prepare U-boot environment image.
   Install u-boot-tools package. Alternatively, if you build your own
   images, OpenWrt provides mkenvimage in host staging directory as well.
   It is recommended to extract environment from the device, and modify
   it, rather then relying on defaults:

   $ sudo touch /srv/tftp/u-boot-env.bin
   $ sudo chmod 666 /srv/tftp/u-boot-env.bin

   On the device, find the MTD partition on which environment resides.
   Beware, it may change depending on currently active firmware image!

   # grep u-boot-env /proc/mtd

   Now, copy over the partition

   # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1

   Store the stock environment in a safe place:

   $ cp /srv/tftp/u-boot-env.bin ~/

   Extract the values from the dump:

   $ strings u-boot-env.bin | tee u-boot-env.txt

   Now clean up the debris at the end of output, you should end up with
   each variable defined once. After that, set the bootcmd variable like
   this:

   bootcmd=bootm 0x9f040000

   You should end up with something like this:

bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),7168k(rcks_wlan.main),7168k(rcks_wlan.bkup),1280k(datafs),256k(u-boot-env)
mtdids=nor0=ar7100-nor0
bootdelay=2
filesize=52e000
fileaddr=81000000
ethact=eth0
stdin=serial
stdout=serial
stderr=serial
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=192.168.0.1
serverip=192.168.0.2
stderr=serial
ethact=eth0

   These are the defaults, you can use most likely just this as input to
   mkenvimage.

   Now, create environment image and copy it over to TFTP root:

   $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
   $ sudo cp u-boot-env.bin /srv/tftp

   This is the same image, gzipped and base64-encoded:
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7. Perform actual installation. Copy over OpenWrt sysupgrade image to
   TFTP root:

   $ sudo cp openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin /srv/tftp

   Now load both to the device over TFTP:

   # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
   # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin -g 10.42.0.1

   Verify checksums of both images to ensure the transfer over TFTP
   was completed:

   # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin

   And compare it against source images:

   $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin

   Locate MTD partition of the primary image:

   # grep rcks_wlan.main /proc/mtd

   Now, write the images in place. Write U-boot environment last, so
   unit still can boot from backup image, should power failure occur during
   this. Replace MTD placeholders with real MTD nodes:

   # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
   # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>

   Finally, reboot the device. The device should directly boot into
   OpenWrt. Look for the characteristic power LED blinking pattern.

   # reboot -f

   After unit boots, it should be available at the usual 192.168.1.1/24.

Return to factory firmware:

1. Boot into OpenWrt initramfs as for initial installation. To do that
   without disassembly, you can write an initramfs image to the device
   using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
   fw_setenv bootcmd ""
3. Concatenate the firmware backups, if you took them during installation using method 2:

   $ cat ruckus_zf7025_fw1_backup.bin ruckus_zf7025_fw2_backup.bin > ruckus_zf7025_backup.bin

3. Write factory images downloaded from manufacturer website into
   fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
   before installation:

   # mtd write ruckus_zf7025_backup.bin /dev/mtd1

4. Reboot the system, it should load into factory firmware again.

Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
  partitions for storage using mtd-concat, and uImage format is used to
  actually boot the system, which rules out the dual-boot capability.
- The 2.4 GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
  OpenWrt by choice.
  It is controlled by data in the top 64kB of RAM which is unmapped,
  to avoid   the interference in the boot process and accidental
  switch to the inactive image, although boot script presence in
  form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
  however not much is available in terms of debugging facitilies.
  1. Login to the rkscli
  2. Execute hidden command "Ruckus"
  3. Copy and paste ";/bin/sh;" including quotes. This is required only
     once, the payload will be stored in writable filesystem.
  4. Execute hidden command "!v54!". Press Enter leaving empty reply for
     "What's your chow?" prompt.
  5. Busybox shell shall open.
  Source: https://alephsecurity.com/vulns/aleph-2019014

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-11-13 22:36:06 +01:00
Ivaylo Ivanov
6afc355b2e ramips: Add support for D-Link DIR-3060 A1
Hardware specification:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HVSINA 128MB
RAM: Micron MT41K128M16JT-125 256MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7615DN 2.4GHz N 2x2:2
WiFi2: MT7615DN 5GHz AC 2x2:2
WiFi3: MT7615N 5GHz AC 4x4:4
Button: WPS, Reset

Flash instructions:
OpenWrt can be installed via D-Link Recovery GUI:

    Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
    Give it ~30 seconds, to boot the recovery mode GUI
    Connect your client computer to LAN1 of the device
    Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
    Call the recovery page for the device at http://192.168.0.1/
    Use the provided emergency web GUI to upload and flash a new firmware to the device

Signed-off-by: Ivaylo Ivanov <iivailo@mail.bg>
2022-11-13 22:36:06 +01:00
Daniel Fuchs
794d1645b3 ramips: add support for Amped Wireless B1200EX
This device is almost identical to the already supported Edimax
EW-7476RP5, the only differences are:
- There is no mode selection slider switch on this device
- The two wireless LEDs are green instead of blue
- Model name in the CSYS header is RN10

Additional changes:
- Moved WiFi LEDs and the slider switch to the individual dt files
- Added ieee80211-freq-limit to the mt7612e radio to properly disable
  2.4GHz band on this radio

Device specifications:
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS/RESET
LED:	- WiFi 5G (green)
	- WiFi 2.4G (green)
	- Signal Strength (green)
	- Power (green)
	- WPS (green)
	- LAN (green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the WPS button
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation:
Upload the sysupgrade image via the default web interface

Signed-off-by: Daniel Fuchs <software@sagacioussuricata.com>
2022-11-13 22:36:06 +01:00
Mikhail Zhilkin
0cfd15552e ramips: add support for Rostelecom RT-SF-1
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
   Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
   firmware
6. Update firmware using web interface with the OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
    printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+------------+
| use | address    | example    |
+-----+------------+------------+
| LAN | label      | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g  | label + 2  | *:74, *:d4 |
| 5g  | label + 3  | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-13 21:51:22 +01:00
Mikhail Zhilkin
e6b99a4e43 ramips: create common dtsi for Sercomm Dxx routers
This commit adds common dtsi for the following Sercomm devices with 256
MB NAND:
Beeline Smartbox TURBO (Sercomm DF3)
Rostelecom RT-SF-1 (Sercomm DKG)

Also fixed typo ("Container" mtd name should be with a capital).

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-13 21:51:22 +01:00
Martin Dziura
a0b25e17ae ramips: glinet_gl-mt300n-v2: allow to use I2C and UART1 pins as GPIO
This is explicitly intended by the official documentation at
https://docs.gl-inet.com/en/3/specification/gl-mt300n-v2/#pcb-pinout

Signed-off-by: Martin Dziura <m.dziura@tum.de>
2022-11-13 21:51:22 +01:00
David Bauer
fdcd383919 kconfig: abort configuration on unset symbol
This fixes the initial patch to cover all cases where unset symbols are
handled in the code.

Fixes commit eaa9c94c75 ("generic: Kconfig: exit on unset symbol")

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-11-13 16:49:30 +01:00
Lech Perczak
1a49b499f1 ipq40xx: dts: remove leftover nodes after DSA conversion
Remove ess-psgmii@98000, edma@c080000 and ess-switch@c000000 nodes.
These nodes are not used after the DSA conversion, but were left over
in a few devices added recently.

ZTE MF289F is omitted on purpose, as for it, these nodes will be removed
together with DSA conversion.

Build tested only, as I only have MF286D from those devices.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-11-13 15:31:54 +01:00
Sven Eckelmann
fc69532eb9 ipq40xx: Convert plasmacloud,pa2200 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"
  - can be used to power the device

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 2" port was used in the past
for "WAN" functionality in OpenWrt.

Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
ce6c9e0328 ipq40xx: utilize nvmem-cells for plasmacloud,pa2200
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
539a5fd624 ipq40xx: Convert plasmacloud,pa1200 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"
  - can be used to power the device

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 2" port was used in the past
for "WAN" functionality in OpenWrt.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
b8bda645fc ipq40xx: utilize nvmem-cells for plasmacloud,pa1200
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Arne Zachlod
364550f9d9 ramips: fix MAC address assignment for rt1800, e7350
previous commit ffa4b5283b introduced a bug which broke the MAC address
assignment for belkin,rt1800 and linksys,e7350.

Fixes: ffa4b5283b ("ramips: add support for Mikrotik LtAP-2HnD")
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2022-11-13 15:17:49 +01:00
Hauke Mehrtens
b97e5ac785 bcm4908: Refresh kernel patches
Refresh the kernel patches for this target. No manual changes.

Fixes: 45ac906c64 ("bcm4908: update DTS files with the latest changes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-11-12 22:53:04 +01:00
Sven Eckelmann
087a8e39be ipq40xx: utilize nvmem-cells for openmesh,a62
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Sven Eckelmann
2b2f14c959 ipq40xx: utilize nvmem-cells for openmesh,a42
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Sven Eckelmann
c6bef1b83a ipq40xx: Convert openmesh,a62 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - can be used to power the device
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 1" port was used in the past
for "WAN" functionality in OpenWrt.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Sven Eckelmann
66a3c32b47 ipq40xx: Convert openmesh,a42 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - can be used to power the device
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 1" port was used in the past
for "WAN" functionality in OpenWrt.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Guillaume Lefebvre
65d9a715fc ipq40xx: D-Link DAP-2610: convert to DSA
Reenable D-Link DAP-2610, convert it to DSA and label port to 'lan', as shown on the case

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
2022-11-12 18:15:55 +01:00
Óscar García Amor
62efb34071 ramips: add support for Cudy WR1300 v2
Specifications:
 - SoC: MediaTek MT7621AT
 - RAM: 128 MB (DDR3)
 - Flash: 16 MB (SPI NOR)
 - WiFi: MediaTek MT7603E, MediaTek MT7613BE
 - Switch: 1 WAN, 4 LAN (Gigabit)
 - Ports: 1 USB 3.0
 - Buttons: Reset, WPS
 - LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS
 - Power: DC 12V 1A tip positive

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:
 - Loads only signed manufacture firmware due to bootloader RSA verification
 - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
 - connect to any lan ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button for image to
   download
 - See http://www.cudytech.com/newsinfo/547425.html

Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
2022-11-12 18:15:55 +01:00
Szabolcs Hubai
18801f2648 ramips: mt7621: use seama-lzma-loader for D-Link DIR-860L B1
Fix the LZMA ERROR 1 with a single line of recipe instead of duplicating
"uimage-lzma-loader".

While reviewing my original submission of commit ce19571004 David
suggested to use $(Device/uimage-lzma-loader), but due to the specific
needs of the vendor bootloader that simple oneliner didn't work.

The new $(Device/seama-lzma-loader) is for those SEAMA capable
bootloaders.

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2022-11-12 18:15:55 +01:00
Szabolcs Hubai
c293b492df ramips: rt3883: use seama-lzma-loader for D-Link DIR-645
In the support topic [0] of the GitHub issue #10634 it was found out
(based on boot logs) that the uimage-lzma-loader (commit 09faa73c53)
never worked, as an earlier workaround (commit 6fba88de19) negated
the recipe:

    3: System Boot system code via Flash.
    ## Booting image at bc050000 ...
    raspi_read: from:50000 len:40
    .raspi_read: from:50000 len:c
    .raspi_read: from:50000 len:1fa000
    ................................We have SEAMA, Image Size = 2072512
    Verifying Checksum ...
    Uncompressing SEAMA linux.lzma ... OK
    ## Transferring control to Linux (at address 80000000) ...
    ## Giving linux memsize in MB, 64

    Starting kernel ...

    [    0.000000] Linux version 5.4.188 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022
    [    0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
    [    0.000000] printk: bootconsolde [early0] enabled
    [    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
    [    0.000000] MIPS: machine is D-Link DIR-645
    [    0.000000] Initrd not found or empty - disabling initrd

Using the new seama-lzma-loader it's able to boot OpenWrt 22.03
and OpenWrt SNAPSHOT too:

    3: System Boot system code via Flash.
    ## Booting image at bc050000 ...
    raspi_read: from:50000 len:40
    .raspi_read: from:50000 len:c
    .raspi_read: from:50000 len:48b004
    .........................................................................We have SEAMA, Image Size = 4763588
    Verifying Checksum ...
    Uncompressing SEAMA linux.lzma ... OK
    ## Transferring control to Linux (at address 80000000) ...
    ## Giving linux memsize in MB, 64

    Starting kernel ...

    OpenWrt kernel loader for MIPS based SoC
    Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
    Decompressing kernel... done!
    Starting kernel at 80000000...

    [    0.000000] Linux version 5.10.144 (xabolcs@ut2004) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20774+2-b71affaf8b) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 Tue Sep 27 23:02:30 2022
    [    0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
    [    0.000000] printk: bootconsole [early0] enabled
    [    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
    [    0.000000] MIPS: machine is D-Link DIR-645
    [    0.000000] Initrd not found or empty - disabling initrd
    [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
    [    0.000000] Zone ranges:
    [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
    [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
    [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
    [    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2

The OKLI Loader is unable to read the flash on this SoC:

    Looking for OpenWrt image... not found! ('0xddbaddba' at 0xbc051000)

0: https://forum.openwrt.org/t/136435

Fixes: GitHub issue #10634 ("V22.03.0 release currently does not work on D-Link DIR-645")
Fixes: 09faa73c53 ("ramips: rt3883: use lzma-loader for DIR-645")
Tested-by: Glenn Fowler <gfowler1@outlook.com>
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2022-11-12 18:15:55 +01:00
Szabolcs Hubai
e7ad68d682 ramips: define lzma-loader recipe for SEAMA devices
Define "Device/seama-lzma-loader" recipe for SEAMA devices to help
contributors avoid doing recipe mistakes.

In a forum topic [0] I was under the impression that the good old
uimage-lzma-loader didn't fix the LZMA ERROR 1 for a device.

It was found out, that the uimage-lzma-loader never worked because the
KERNEL variable was overriden earlier (also an LZMA ERROR 1 related
commit, 6fba88de19), and the "use lzma-loader" fix (commit
09faa73c53) didn't catch that to include the "loader-kernel" part.

I contributed an LZMA ERROR 1 fix (commit ce19571004) for the SEAMA
device D-Link DIR-860L B1, where I had to duplicate the whole
uimage-lzma-loader recipe because of the special needs of the vendor
bootloader.

This new recipe reuse most of uimage-lzma-loader's KERNEL definiton to
avoid duplication.

It uses "relocate-kernel" as it needed for D-Link DIR-860L B1 to
boot from flash, and it's compatible with D-Link DIR-645 too.

It repacks lzma-loader with lzma for kernel (without uImage), because
these weird hacked vendor bootloaders accepts only LZMA compressed
kernels from flash:

    We have SEAMA, Image Size = 4759794
    Verifying Checksum ...
    Uncompressing SEAMA linux.lzma ... OK

It uses uImage header for initramfs kernel to be little bit verbose.

0: https://forum.openwrt.org/t/136435/10

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2022-11-12 18:15:55 +01:00
Arne Zachlod
ffa4b5283b ramips: add support for Mikrotik LtAP-2HnD
Mikrotik LtAP-2HnD is a outdoor/automotive WLAN 4 router with integrated GPS
receiver and two mPCIe slots.

Specifications:
* SoC: MT7621A
* RAM: 128 MiB Nanya NT5CC64M16GP-DI
* Flash: 16 MiB winbond W25Q128JV
* WLAN:
  * Atheros AR9382 with power amplifier SKY 85330 (2x2 internal antennas,
    with RF switches for external connectors)
* Ethernet: 1 Gbps, single port
* USB Host: USB 2.0 Speeds
* Serial: 115200 baud
* LEDs: Power, System, GPS, 5* RSSI
*  mPCIe:
   * miniPCIe slot 1: PCIe and USB 2.0 Host (via switch shared with USB Host)
   * miniPCIe slot 2: USB 2.0 and 3.0
* SIM Cards:
  * Slot 1 Connected to mPCIe slot 1
  * Slot 2 and 3 connected to mPCIe slot 2 via switch
* GPS: MTK 3333 on serial port 2 (/dev/ttyS1), 115200 baud and PPS on gpio 14

gpios are exposed to /sys/class/gpio:

* usb-select: swithes USB 2.0 interface between external port and internal
mPCIe slot 1 default is the external USB interface
* gps-reset: resets the GPS interface chip
* sim-select: switches between sim slot 2 and 3 connected to mPCIe slot 2
* gps-ant-select: switches GPS antenna between internal antenna and SMA
connected antenna
* lte-reset: resets mPCIe slot 2

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2022-11-12 18:15:55 +01:00
Will Moss
5a1af6ed62 ath79: fix MAC address assignment for TP-Link ar7241 devices
On TP-Link ar7241 devices LAN and WAN interfaces are swapped. Keeping
that in mind fix MAC address assignment as used in vendor firmware:
LAN MAC - main MAC stored in u-boot and printed on label
WAN MAC - LAN MAC + 1

Signed-off-by: Will Moss <willormos@gmail.com>
2022-11-12 17:10:12 +01:00
Shiji Yang
4778f6e959 ath79: move usb led trigger node to SoC dtsi
These frequently used usb led triggers are universal. They should be
moved to SoC dtsi.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-12 17:10:12 +01:00
John Audia
e7bd3767a9 kernel: bump 5.10 to 5.10.154
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-12 17:05:13 +01:00
John Audia
0252c0b1bc kernel: bump 5.15 to 5.15.78
All patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-12 17:05:13 +01:00
Quintin Hill
4c3f664c2f kernel: backport some Bluetooth RTL8761 USB IDs
These USB IDs appear in the 5.15 stable kernel series but not the 5.10
stable series.

Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
2022-11-12 17:05:13 +01:00
Quintin Hill
5e6e45b7ff kernel: backport RTL8761B FW name change to v5.10
Make the firmware filenames referenced by the module consistent for
v5.10 and v5.15 kernels.  Backport two upstream patches a cleanup commit
and the commit making the change, the former is required for the latter
to apply cleanly.

Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
2022-11-12 17:05:13 +01:00
Rafał Miłecki
797177ad85 kernel: update U-Boot nvmem driver to v6.2 release version
Backport queued patches that
1. Fix CRC32 calculation for redundant images
2. Fix CRC32 on big-endian
3. Fix parting images with Broadcom header

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-12 11:42:05 +01:00
Rafał Miłecki
ce296b1aeb bcm4908: refresh kernel 5.15 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-11 17:21:55 +01:00
Rafał Miłecki
66b6414a20 bcm4908: prepare support for kernel 5.15
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-11 17:21:55 +01:00
Rafał Miłecki
45ac906c64 bcm4908: update DTS files with the latest changes
The most affecting change is move of files from bcm4908/ to the bcmbca/.
That required updating few paths.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-11 15:37:57 +01:00
Daniel Golle
e586de8dbf
ath79: add support for Teltonika RUT300
Add support for the Teltonika RUT300 rugged industrial Ethernet router

Hardware
--------
SoC:    Qualcomm Atheros QCA9531
RAM:    64M DDR2 (EtronTech EM68B16CWQK-25IH)
FLASH:  16M SPI-NOR (Winbond W25Q128)
ETH:    4x 100M LAN (QCA9533 internal AR8229 switch, eth0)
        1x 100M WAN (QCA9533 internal PHY, eth1)
UART:   115200 8n1, same debug port as other Teltonika devices
USB:    1 single USB 2.0 host port
BUTTON: Reset
LED:    1x green power LED (always on)
        5x yellow Ethernet port LED (controlled by Linux)
        WAN port LED is used as boot status and upgrade indicator as
        the power LED cannot be controlled in software.

Use the *-factory.bin file to intially flash the device using the
vendor firmware's Web-UI.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-10 21:35:34 +00:00
Felix Fietkau
04b8ad60fd kernel: more fixes for mtk_eth_soc performance optimization
- fix features sync between netdevs
- fix crash in dsa_switch_rcv

Fixes: ceb1451c10 ("kernel: add mediatek soc ethernet performance improvements")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-10 22:27:18 +01:00
Felix Fietkau
7bd314a577 kernel: fix vlan parsing issue in mediatek ethernet driver
Check the vlan rx offload flag
Sync features across netdevs

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-10 13:20:57 +01:00
Rafał Miłecki
e4770db163 kernel: support "linux,rootfs" DT property for splitting rootfs
OpenWrt's support for splitting rootfs (to create an extra "rootfs_data"
partition) is limited to partitions called "rootfs". Upstream kernel
allows any name partition to be rootfs if it has "linux,rootfs" property
set. Add split support to such partitions in OpenWrt code.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-10 12:47:22 +01:00
Rafał Miłecki
8cdafa149e bcm53xx: update DTS files with the latest changes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-10 09:51:25 +01:00
Weiping Yang
9945d05171 ipq40xx: add support for GL.iNet GL-A1300
Specifications:
SOC:		Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:		256 MiB
FLASH1:		4 MiB NOR
FLASH2:		128 MiB NAND
ETH:		Qualcomm QCA8075
WLAN1:		Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:		Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB:		1 x USB 3.0 port
Button:		1 x Reset button
Switch:		1 x Mode switch
LED:		1 x Blue LED + 1 x White LED

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2022-11-09 23:34:37 +01:00
Edward Chow
79107116d1 ath79: calibrate TL-WDR4900 v2 with nvmem-cells
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-09 22:55:33 +01:00
Shiji Yang
8d4c22a956 ath79: add missing clock name strings in SoC dtsi
For all SoC in the ath79 target, the PLL controller provides 3 main
clocks "cpu", "ddr" and "ahb" through the input clock "ref".

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-09 22:55:33 +01:00
Shiji Yang
520c90854c ath79: move reference clock node to SoC dtsi
AR7161, AR724x, AR9132 and QCA95xx only support fixed frequency external
crystal oscillator, so move reference clock node to SoC dtsi files.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-09 22:55:33 +01:00
Felix Fietkau
a06e023b4e mac80211: remove old legacy legacy drivers
Get rid of drivers that are either limited to 802.11b/g or don't even support
cfg80211/mac80211. Most of these are either limited to boards that we don't even
support anymore because of firmware size, or were only used for custom hacks by
a really small number of users in the past.
Let's get rid of those to reduce the maintenance effort and the number of useless
packages

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:44:28 +01:00
Felix Fietkau
f753316f4a mediatek: filogic: enable maxlinear PHY support, refresh config
Needed for the 7986 RFB1 board

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:55 +01:00
Felix Fietkau
5faff99c7b mediatek: filogic: fix mt7986a ethernet devicetree entries
Add all ports, rename DSA ports to start at lan1

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:51 +01:00
Felix Fietkau
4f1e54801e mediatek: drop the use of device tree overlays on mt7986a-rfb board
The boot loader does not support it. Instead make NAND the default image for
this board

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:45 +01:00
Felix Fietkau
ceb1451c10 kernel: add mediatek soc ethernet performance improvements
- implement multiqueue via qdma hardware shaper to deal with ports with different speeds
- implement hardware DSA untagging
- add NETIF_F_ALL_TSO to reduce unnecessary segmentation

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 18:18:27 +01:00
Edward Matijevic
2964e5024c
ipq806x: kernel ramoops storage for C2600/AD7200
Define the kernel crash log storage ramoops/pstore feature
for C2600/AD7200 and add kmod-ramoops to default.

Tested with C2600 only.

Signed-off-by: Edward Matijevic <motolav@gmail.com>
2022-11-09 17:07:15 +01:00
David Bauer
10ba380ec3 ramips: define loadaddr for U6 Lite DTB
The Ubiquiti UniFi 6 Lite does not correctly align the FDT by always
setting fdt_high to 0xffffffff when invoking the bootubnt command.

Work around this issue by loading the DTB to a valid,aligned address, so
the bootloader does not have to relocate the FDT automatically.

Note: The device does read the kernel before invoking bootm on the FIT
image to 0x86000000.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-11-08 12:16:43 +01:00
Rafał Miłecki
d33e49857e kernel: backport support for "linux,rootfs" in DT
This DT property allows marking flash partition that Linux should use as
a root device. It's useful for devices that don't use U-Boot and cmdline
parser for partitioning. It may be used with "fixed-partitions" or some
dynamic partitioning based on flash content.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-08 09:12:16 +01:00
Rafał Miłecki
6a64eb2664 kernel: split out mtd hack for CONFIG_FIT_PARTITION + rootfs
This is some hack on top of our old hack. Use separated patch for it so
it's easier to understand and actually possible to describe. We should
ideally get rid of this (and we actually did with kernels 5.15+).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-08 09:12:05 +01:00
Michael Lyle
961e01fc67 ramips: gl-mt1300: downclock SPI to 50MHz
The SPI max frequency was set to 80MHz, considerably higher than the
vendor clocks it in their firmware (10MHz).  Multiple users reported
jffs2 corruption/instability in GitHub issue #10461.

My unit has a W25Q256; datasheet specifies maximum SPI frequency for
read command of 50MHz.

Thanks to @DragonBlueP for suggesting to eliminate m25p,fast-read;
and @MPannen1979 for identifying the problem.

Fixes: #10461
Signed-off-by: Michael Lyle <mlyle@lyle.org>
2022-11-07 12:54:31 +01:00
Sungbo Eo
02aa7a2bb9 ramips: fix TP-Link RE200 v3/v4 LEDs
Set power LED to gpio 43 instead of 44 for v3 and v4.
Set red wifi LED to gpio 40 (was assigned to `red:wifi5g`).

Tested by the author of the initial v3 and v4 commit.

Reported-by: Richard Fröhning <misanthropos@gmx.de>
Tested-by: Richard Fröhning <misanthropos@gmx.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-11-07 12:33:42 +01:00
Kuan-Yi Li
f795ecc0dd sdk: use git-src-full to allow Git versioning
$(AUTORELEASE) uses Git log to determine releases and package timestamps.

Base feed is shallow cloned by default in generated SDK, resulting in
an incomplete Git log and therefore different local package versions than
offered upstream.

This patch complements commit 7fae1e5677 by setting the base feed to use
`src-git-full` to solve that.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-06 17:08:23 +01:00
Alan Luck
aca8bb5cc3 ath79: expand rootfs for DIR-825-B1 with unused space
Expand currently unused flash space to roofs for DIR-825-B1 by using the same
flash space as the old ar71xx big image without moving the caldata.

With some testing this partition is use by the OEM firmware
but if changed is regenerated which allows reverting to OEM firmware

Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
2022-11-06 01:03:16 +01:00
Korey Caro
12cee86989 ath79: add support to TrendNet TEW-673GRU
Add support for the TrendNet TEW-673GRU to ath79.
This device was supported in 19.07.9 but was deprecated with ar71xx.
This is mostly a copy of D-Link DIR-825 B1.
Updates have been completed to enable factory.bin and sysupgrade.bin both.
Code improvements to DTS file and makefile.

Architecture   |  MIPS
Vendor         |  Qualcomm Atheros
bootloader     |  U-Boot
System-On-Chip |  AR7161 rev 2 (MIPS 24Kc V7.4)
CPU/Speed      |  24Kc V7.4 680 MHz
Flash-Chip     |  Macronix MX25L6405D
Flash size     |  8192 KiB
RAM Chip:      |  ProMOS V58C2256164SCI5 × 2
RAM size       |  64 MiB
Wireless       |  2 x Atheros AR922X 2.4GHz/5.0GHz 802.11abgn
Ethernet       |  RealTek RTL8366S Gigabit w/ port based vlan support
USB            |  Yes 2 x 2.0

Initial Flashing Process:
	1) Download 22.03 tew-673gru factory bin
	2) Flash 22.03 using TrendNet GUI

OpenWRT Upgrade Process
	3) Download 22.03 tew-673gru sysupgrade.bin
	4) Flash 22.03 using OpenWRT GUI

Signed-off-by: Korey Caro <korey.caro@gmail.com>
2022-11-06 00:51:58 +01:00
Linos Giannopoulos
78110c3b5f ramips: add support for TP-Link MR600 V2(EU)
MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation
etc. and can reportedly achieve higher bandwidth with it.

- Specifications:

* SoC: Mediatek MT7621DAT 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* LTE Modem: Qualcomm MDM9240
* WiFi 5GHz: Mediatek MT7613BEN
* WiFi 2.4GHz: Mediatek MT7603EN
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console (115200 8n1), J1(GND:3)
* Buttons: Reset, WPS.
* LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2,
  Signal3

- MAC Addresses:

OEM firmware configuration:
54:af:97:xx:xx:7b : 2.4G
54:af:97:xx:xx:7a : 5G
54:af:97:xx:xx:7c : LTE
54:af:97:xx:xx:7b : LAN (label)
54:af:97:xx:xx:7c : WAN

- Installation:

1. Download the OpenWrt initramfs-image.

Place it into a TFTP server root directory and rename it to openwrt.img
Configure the TFTP server to listen at 192.168.0.5/24.

3. Connect to the serial console.

Attach power and interrupt the boot procedure when prompted (type `tpl`).

Credentials are admin / 1234

4. Configure U-Boot for booting OpenWrt from ram

 $ tftpboot
 $ bootm

5. Transfer the OpenWrt sysupgrade image to the device.

- LTE:

In order to setup the wwan0 interface:
1. Add a `qmi` proto interface under `/etc/config/network`, e.g.:
```
config interface 'wwan0'
        option device '/dev/cdc-wdm0'
        option proto 'qmi'
        option pincode 'XXXX'
        option apn 'your_isp_apn'
```

2. Add `wwan0` interface to the `wan` firewall zone
3. `/etc/init.d/network restart`

Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
2022-11-05 23:13:16 +01:00
Shiji Yang
f7f9203854 ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based
on Tenbay WR1800K. They have the same hardware circuits and u-boot.
SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile),
SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these
models run the same firmware.

Specifications:
 SOC:      MT7621 + MT7905 + MT7975
 ROM:      128 MiB
 RAM:      256 MiB
 LED:      status *3 R/G/B
 Button:   reset *1 + wps/mesh *1
 Ethernet:      lan *3 + wan *1 (10/100/1000Mbps)
 TTL Baudrate:  115200
 TFTP Server:   192.168.1.254
 TFTP IP:       192.168.1.28 or 192.168.1.160 (when envs is broken)

MAC Address:
 use        address               source
 label      30:xx:xx:xx:xx:62     wan
 lan        30:xx:xx:xx:xx:65     factory.0x8004
 wan        30:xx:xx:xx:xx:62     factory.0x8004 -3
 wlan2g     30:xx:xx:xx:xx:64     factory.0x0004
 wlan5g     32:xx:xx:xx:xx:64     factory.0x0004 set 7th bit

TFTP Installation (initramfs image only & recommend):
1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
   directory of the tftp server. (tftpd64 is a good choice for Windows)
3. Start the TFTP server, plug in the power supply, and wait for the
   system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin", we need
   it to back to stock firmware.
5. Use "fw_printenv" command to list envs.
   If "firmware_select=2" is observed then set u-boot enviroment:
   /# fw_setenv firmware_select 1
6. Apply sysupgrade.bin in OpenWrt LuCI.

Web UI Installation:
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs.
   If "firmware_select=2" is observed then set u-boot enviroment:
   /# fw_setenv firmware_select 1
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.

Recovery to stock firmware:
a. Upload "firmware.bin" to OpenWrt /tmp, then execute:
   /# mtd -r write /tmp/firmware.bin firmware
b. We can also write factory image "UploadBrush-bin.img" to firmware
   partition to recovery. Upload image file to /tmp, then execute:
   /# mtd erase firmware
   /# mtd -r write /tmp/UploadBrush-bin.img firmware

How to extract stock firmware image:
  Download stock firmware, then use openssl:
  openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \
  -out "firmware.tar.tgz" -k QiLunSmartWL

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 22:38:01 +01:00
Alexander Horner
53f2e438cb ramips: add support for Zbtlink ZBT-WG1602-V04
Description heavily based on commit
7e89421a7c by
Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have
been removed

Completed with great help from \x on IRC. Thanks, \x!

Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe
slots with USB and SIM only and another one which is a pure miniPCIe
slot as well as five Gigabit Ethernet ports (4xLAN + WAN).

Specification:

* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2)
* WLAN 5GHz: MT7662E (.11nac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 3.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled,
  1 power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)

Additional HW information:

* SoC USB port 1 is shared by internal miniPCIe slot and external
  Type-A USB port, USB D+/D- lines are toggled between ports using a
  GPIO controlled DPDT switch.

Installation:

The kernel image can be installed directly onto the device via a browser
to 192.168.1.1 using the built in firmware recovery Web UI available.
It can be accessed by pushing the reset button in, applying power and
holding the reset button for approximately 10 seconds. When the kernel
image has been flashed, you can access LuCI and upload the sysupgrade
as normal.

Signed-off-by: Alexander Horner <ahorner@programmer.net>
2022-11-05 21:12:25 +01:00
Shiji Yang
7a504c151d ramips: add support for Youku X2
Specifications:
  SOC:      MT7620AN + MT7612EN
  RAM:      128 MiB DDR2
  Flash:    16 MiB (Winbond W25Q28FVFG)
  WLAN:     2.4G + 5G
  LAN:      LAN ports *2
  WAN:      WAN port *1
  USB:      USB2.0 *1
  SD Card:  MicroSD *1
  Buttons:  Reset *1
  LEDs: ethernet *3, system, usb, wlan2g, wlan5g

MAC Address:
  use        address               source
  label      54:36:9b:xx:xx:ac     lan
  lan        54:36:9b:xx:xx:ac     factory.0x0028
  wan        54:36:9b:xx:xx:ad     factory.0x002e
  wlan2g     54:36:9b:xx:xx:ae     factory.0x0004
  wlan5g     54:36:9b:xx:xx:af     factory.0x8004

Installation:
1. Apply initramfs-kernel.bin in stock firmware Web UI.
2. Install sysupgrade.bin on OpenWrt and do not retain any configuration.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 21:12:24 +01:00
Shiji Yang
eba0a8deb6 ramips: improve compatibility for Youku YK-L2 and YK-L1 series
Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install
initramfs-kernel.bin from the stock firmware Web UI. At the same time,
this change makes it possible to boot OpenWrt with the official u-boot.

Notice:
Since the stock firmware is based on OpenWrt and the configuration
will be retained by default during the upgrade process, so we must use
initramfs-kernel.bin to do a initial installation. After the system
restarts, install sysupgrade.bin and do not retain any configuration.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 21:12:24 +01:00
Martin Schiller
1e028ac51e kernel: further cleanup of xfrm[4|6]_mode*
In my commit da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_*
modules") I missed a few default config options and description entries.
Those should be gone as well.

Fixes: da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_* modules")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-11-05 16:28:33 +01:00
Luiz Angelo Daros de Luca
1ee635c561 realtek: fix typo in debug message
vid_end was mentioned twice.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2022-11-05 16:27:21 +01:00
John Audia
1eebe72a80 kernel: bump 5.15 to 5.15.77
Manually rebased:
   bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
   bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
   bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
   bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
   lantiq/patches-5.15/0028-NET-lantiq-various-etop-fixes.patch

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-05 16:26:38 +01:00
John Audia
87edb650c7 kernel: bump 5.10 to 5.10.153
Manually rebased:
  bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
  lantiq/patches-5.10/0028-NET-lantiq-various-etop-fixes.patch

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-05 16:26:00 +01:00
Nick Hainke
29d987fc89 mediatek: replace mt7986 watchdog assert patch with upstream
Replace "920-watchdog-add-mt7986-assert.patch" with upstreamed
- 920-v5.16-watchdog-mtk-add-disable_wdt_extrst-support.patch
- 921-v5.19-watchdog-mtk_wdt-mt7986-Add-toprgu-reset-controller.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
61a9367b86 mediatek: mt7629: add tag to upstreamed patches
The patches were upstreamed.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
0c8d84a642 mediatek: add tag for upstreamed patches
The patches were upstreamed.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
e8080ce89b mediatek: mt7986: add tag to upstreamed patches
The patch "210-pinctrl-mediatek-add-support-for-MT7986-SoC.patch" and
"212-clk-mediatek-add-mt7986-clock-support.patch" are upstreamed.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
e4270d6493 mediatek: mt7622: add tag to upstreamed patches
The patches "191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch"
and "192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch" are
upstreamed to 5.19.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Aleksander Jan Bajkowski
985d59cdf0 mediatek: filogic: disable swconfig
This subtarget supports 3 devices:
 * Bananapi BPi-R3 (added in a96382c1bb),
 * MediaTek MTK7986 rfba AP (added in cffc77ae55),
 * MediaTek MTK7986 rfbb AP (added in cffc77ae55).

This subtarget supports DSA from the beginning. It looks like CONFIG_SWCONFIG
was copied from another config when the subtarget was created.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-05 14:02:13 +00:00
Aleksander Jan Bajkowski
c4f63f7364 mediatek: filogic: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-05 14:02:13 +00:00
Rafał Miłecki
6198eb3e64 bcm4908: backport upstream BQL support for bcm4908_enet
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-03 07:38:35 +01:00
Hauke Mehrtens
e42ec112a4 kernel: Refresh generic patches
This patch was out of sync.

Fixes: 1673b7dca3 ("kernel: backport fixes for MediaTek Ethernet driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-11-03 00:25:34 +01:00
Daniel Golle
1673b7dca3 kernel: backport fixes for MediaTek Ethernet driver
Backport patches from net-next which fix possible memory and resource
leaks in the error codepaths of WED initialization.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-02 15:53:34 +00:00
Daniel Golle
9721a42a27
kernel: support hw flow-offloading counters on newer MediaTek SoCs
The packet processing engine (PPE) found in newer ARM-based MediaTek
SoCs provides packet and byte counters for offloaded streams.
Import pending patch reading and using those counters.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-02 11:41:56 +00:00
Daniel Golle
82a05ce14b
mediatek: remove obsolete patch
The patch enabling hardware flow offloading support on the MT7623 SoC
has been merged upstream as of Linux 5.13. Remove our local patch which
wrongly got forward-ported and now actually enables hardware flow
offloading for the MT2701 SoC family (unsupported in OpenWrt).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-02 11:41:50 +00:00
Sander Vanheule
75c576d4c4 realtek: mark clock source as continuous
After replacing the R4K event timer and clock source with the new
Realtek Otto timer, performance for RTL839x devices was severely
impacted, as reported by Hiroshi.

Research by Markus showed that after commit 4657a5301e ("realtek:
avoid busy waiting for RTL839x PHY read/write"), the ethernet driver
could only update a phy once per timer interval, which also heavily
impacted boot time. On e.g. a Zyxel GS1900-48, this added around a
minute to the time to fully initialise the switch.

By marking the otto clocksource as continuous, the kernel enables it to
be used for high resolution timers. This allows readx_poll_timeout() to
sleep for less than one system timer interval, reducing system dead
time.

Link: https://github.com/openwrt/openwrt/issues/11117
Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Cc: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> # Panasonic Switch-M48eG PN28480K
Tested-by: Jan Hoffmann <jan@3e8.eu> # HPE 1920-8G, HPE 1920-48G
2022-11-01 09:13:11 +01:00
Rosen Penev
3b93651072 target/realtek: use netif_receive_skb_list
Small performance improvement on rx.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-11-01 09:09:24 +01:00
Daniel Golle
e131a66e30
mediatek: consider adc_oe thermal calibration value in efuse
The use of the adc_oe value stored in the efuse has been dropped in
MediaTek's SDK during a recent refactorization of the temperature
calculation formula. Don't ignore this offset value and again include
it in raw-to-deg-celsius calculation.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-31 22:37:05 +00:00
Volodymyr Puiul
08e153c3c3 ramips: add support for YunCore FAP690
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI NOR
- Wi-Fi:
    - MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 1x 1GiE via MT7530
- UART: J4 (115200 baud)
    - Pinout: [3V3] (TXD) (RXD) (GND)

- Bootloader: U-Boot
- Buttons:
    - SW1 - no label on the box, combined with led
- Led: Status. RGB controlled by
    - GPIO 14 - green color
    - GPIO 15 - red color
    - GPIO 16 - blue color

Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
it will not boot.

MAC addresses as verified by OEM firmware:
vendor   source
LAN      factory 0x4 (label)
5g       factory 0x4 (label)
2g       label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
	4-th byte

Example
label:  44:xx:xx:b7:xx:xx
lan:    44:xx:xx:b7:xx:xx
2g      46:xx:xx:c7:xx:xx
5g      44:xx:xx:b7:xx:xx

Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2022-10-31 22:01:49 +01:00
Martin Schiller
da5c45f4d8 kernel: remove handling of xfrm[4|6]_mode_* modules
For kernel versions before 5.2, the required IPsec modes have to be
enabled explicitly (they are built-in for newer kernels).

Commit 1556ed155a ("kernel: mode_beet mode_transport mode_tunnel xfram
modules") tried to handle this, but it does not really work.

Since we don't support these kernel versions anymore and the code is
also broken, let's remove it.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[Remove old generic config options too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-31 21:58:15 +01:00
Hauke Mehrtens
95c216806b at91: Remove CONFIG_PINCTRL_MCP23S08 configuration option
The CONFIG_PINCTRL_MCP23S08 configuration option is already unset in the
generic kernel configuration.

Fixes: f938512af6 ("target/at91: replace gpio-mcp23s08 with pinctrl-mcp23s08-spi update config")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-31 00:46:15 +01:00
Hauke Mehrtens
d15fed98ec Revert "at91:"
This reverts commit 7cc6ffa1b9.

This should have been folded in an other commit.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-31 00:45:52 +01:00
Hauke Mehrtens
7cc6ffa1b9 at91:
[CONFIG_PINCTRL_MCP23S08 is already unset in generic config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-30 23:37:53 +01:00
Volodymyr Puiul
3d14c610e8 ramips: add support for YunCore FAP640
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI
- Wi-Fi:
    - MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN
- UART: J4 (115200 baud)
    - Pinout: [3V3] (TXD) (RXD) (GND)
- Power: 802.11af/at PoE;

- Bootloader: U-Boot
- Buttons:
    - Reset
- LEDs:
    - Status - RGB controlled by
      - GPIO 14 LOW - green color
      - GPIO 15 LOW- red color
      - GPIO 16 LOW - blue color
    - WAN - gren color, controlled by switch GPIO 12 LOW
    - LAN1 - gren color, controlled by switch GPIO 9 HIGH
    - LAN2 - gren color, controlled by switch GPIO 6 LOW
    - LAN3 - gren color, controlled by switch GPIO 3 LOW
    - LAN4 - gren color, controlled by switch GPIO 0 LOW

Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
router will not boot.

MAC addresses with OEM firmware:
vendor   source
lan      factory 0x4 (label)
5g       factory 0x4 (label)
2g       label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
  4-th byte

Example
label:  44:xx:xx:b7:xx:xx
lan:    44:xx:xx:b7:xx:xx
2g      46:xx:xx:c7:xx:xx
5g      44:xx:xx:b7:xx:xx

Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2022-10-30 23:14:45 +01:00
Csaba Sipos
cc8b8f1b41 ipq40xx: add support for MikroTik hAP ac3 LTE6 kit
This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD
(hAP ac³ LTE6 kit), an  indoor dual band, dual-radio 802.11ac
wireless AP with built-in Mini PCI-E LTE modem, one USB port, five
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/hap_ac3_lte6_kit for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4019
 - RAM: 256 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae
   · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae
 - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port
 - 1x USB Type A port
 - 1x Mini PCI-E port (supporting USB)
 - 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6)

Installation:

Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6).

0. Export your MikroTik license key (in case you want to use the device with RouterOS later)
1. Boot the initramfs image via TFTP
2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder
3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin
4. Recovery to factory software is possible via Netinstall:
   https://help.mikrotik.com/docs/display/ROS/Netinstall

Signed-off-by: Csaba Sipos <metro4@freemail.hu>
2022-10-30 23:14:45 +01:00
Florian Eckert
80edacc8a6 target/mxs: replace gpio-mcp23s08 with pinctrl-mcp23s08
The dependency on the kernel module gpio-mcp23s08 is replaced by
pinctrl-mcp23s08-spi and pinctrl-mcp23s08-i2c, as the gpio-mpc23s08 kernel
module no longer exists.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Florian Eckert
29ae20519a kernel: remove CONFIG_GPIO_MCP23S08 from default kernel configs
The kernel config option 'CONFIG_GPIO_MCP23S08' no longer exists.
Therefore, it is removed from the generic kernel configuration for
linux-5.10 and linux-5.15.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Florian Eckert
f938512af6 target/at91: replace gpio-mcp23s08 with pinctrl-mcp23s08-spi update config
Adapt the device package to no longer use the gpio-mcp23s08 but instead
use the pinctrl-mcp23s08-spi. In addition, the kernel configuration was
adapted so that this can be built as a module and does not have to be
integrated directly into the kernel for this target.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Edward Chow
50f727b773 ath79: add support for Linksys EA4500 v3
Add support for the Linksys EA4500 v3 wireless router

Hardware
--------
SoC:    Qualcomm Atheros QCA9558
RAM:    128M DDR2 (Winbond W971GG6KB-25)
FLASH:  128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN:   QCA9558 3T3R 802.11 bgn
        QCA9580 3T3R 802.11 an
ETH:    Qualcomm Atheros QCA8337
UART:   115200 8n1, same as ea4500 v2
USB:	1 single USB 2.0 host port
BUTTON: Reset - WPS
LED:    1x system-LED
        LEDs besides the ethernet ports are controlled
        by the ethernet switch

MAC Address:
 use        address(sample 1)    source
 label      94:10:3e:xx:xx:6f   caldata@cal_macaddr
 lan        94:10:3e:xx:xx:6f   $label
 wan        94:10:3e:xx:xx:6f   $label
 WiFi4_2G   94:10:3e:xx:xx:70   caldata@cal_ath9k_soc
 WiFi4_5G   94:10:3e:xx:xx:71   caldata@cal_ath9k_pci

Installation from Serial Console
------------

1. Connect to the serial console. Power up the device and interrupt
   autoboot when prompted

2. Connect a TFTP server reachable at 192.168.1.0/24
   (e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
   initramfs image as "openwrt.bin"

3. To test OpenWrt only, go to step 4 and never execute step 5;
   To install, auto_recovery should be disabled first, and boot_part
   should be set to 1 if its current value is not.

   ath> setenv auto_recovery no
   ath> setenv boot_part 1
   ath> saveenv

4. Boot the initramfs image using U-Boot

   ath> setenv serverip 192.168.1.66
   ath> tftpboot 0x84000000 openwrt.bin
   ath> bootm

5. Copy the OpenWrt sysupgrade image to the device using scp and
   install it like a normal upgrade (with no need to keeping config
   since no config from "previous OpenWRT installation" could be kept
   at all)

   # sysupgrade -n /path/to/openwrt/sysupgrade.bin

Note: Like many other routers produced by Linksys, it has a dual
      firmware flash layout, but because I do not know how to handle
      it, I decide to disable it for more usable space. (That is why
      the "auto_recovery" above should be disabled before installing
      OpenWRT.) If someone is interested in generating factory
      firmware image capable to flash from stock firmware, as well as
      restoring the dual firmware layout, commented-out layout for the
      original secondary partitions left in the device tree may be a
      useful hint.

Installation from Web Interface
------------

1. Login to the router via its web interface (default password: admin)

2. Find the firmware update interface under "Connectivity/Basic"

3. Choose the OpenWrt factory image and click "Start"

4. If the router still boots into the stock firmware, it means that
   the OpenWrt factory image has been installed to the secondary
   partitions and failed to boot (since OpenWrt on EA4500 v3 does not
   support dual boot yet), and the router switched back to the stock
   firmware on the primary partitions. You have to install a stock
   firmware (e.g. 3.1.6.172023, downloadable from
   https://www.linksys.com/support-article?articleNum=148385 ) first
   (to the secondary partitions) , and after that, install OpenWrt
   factory image (to the primary partitions). After successful
   installation of OpenWrt, auto_recovery will be automatically
   disabled and router will only boot from the primary partitions.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-10-30 23:14:45 +01:00
John Audia
910bdda6af kernel: bump 5.15 to 5.15.76
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:57:25 +01:00
John Audia
af1e3439a8 rockchip: armv8: add CONFIG_ARM64_ERRATUM_1742098
5.15.76 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:55:00 +01:00
John Audia
86ba286766 mvebu: cortexa72: add CONFIG_ARM64_ERRATUM_1742098
5.15.76 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:55:00 +01:00
John Audia
8e7cc06254 kernel: add # CONFIG_ARM64_ERRATUM_1742098
Introduced with 5.15.76[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
a34255b795 kernel: bump 5.15 to 5.15.75
Removed upstreamed:
   bcm27xx/patches-5.15/950-0446-drm-vc4-Fix-timings-for-VEC-modes.patch[1]

Manually rebased:
   patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
   bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
   bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
   bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

All other patches automatically rebased

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.75&id=2810061452f9b748b096ad023d318690ca519aa3

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
a133423c59 kernel: add # CONFIG_ARM64_ERRATUM_2441007 symbol
Introduced with 5.15.75.[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.75&id2=v5.15.74

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
52400e167d kernel: bump 5.10 to 5.10.152
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
dab23d04af layerscape: armv8_64b: add CONFIG_ARM64_ERRATUM_1742098
5.10.152 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].

https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.10.152&id2=v5.10.151

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
7a27ac605c kernel: bump 5.10 to 5.10.151
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
aa2fa2eb76 kernel: bump 5.10 to 5.10.150
Manually rebased:
  bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-30 17:52:42 +01:00
Chukun Pan
641e4f2f04 mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128 MB
  RAM: K4A4G165WF-BCWE 512 MB
  Ethernet: 4x 10/100/1000 Mbps
  WiFi1: MT7976GN 2.4GHz ax 4x4
  WiFi2: MT7976AN 5GHz ax 4x4
  Button: Mesh, Reset

Flash instructions:
  1. Gain ssh and serial port access, see the link below:
     https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
  2. Use ssh or serial port to log in to the router, and
     execute the following command:
     nvram set boot_wait=on
     nvram set flag_boot_rootfs=0
     nvram set flag_boot_success=1
     nvram set flag_last_success=1
     nvram set flag_try_sys1_failed=8
     nvram set flag_try_sys2_failed=8
     nvram commit
  3. Set a static ip on the ethernet interface of your computer
     (e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
  4. Download the initramfs image, rename it to initramfs.bin,
     and host it with the tftp server.
  5. Interrupt U-Boot and run these commands:
     setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
     saveenv
     tftpboot initramfs.bin
     bootm
  6. After openwrt boots up, use scp or luci web
     to upload sysupgrade.bin to upgrade.

Revert to stock firmware:
  Restore mtdparts back to default, then use the
  vendor's recovery tool (Windows only).

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-30 14:30:22 +00:00
Olliver Schinagl
f4849c0ab7 realtek: Fix CRC offloading for rtl83xx
In rtl83xx_set_features we set bit 3 to enable, and bit 4 to disable
checksuming. Looking at rtl93xx_set_features we however see that for
both enable and disable the same bit is used (bit 4). This can't be
right, especially as bit 4 for rtl83xx seems to be Collision threshold
occupying 2 bits. Change this to make this more logical.

Fixes: 9e8d62e421 ("realtek: enable CRC offloading")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-10-29 11:18:04 +02:00
Christian Marangi
5384c9337f
ipq806x: disable ea8500 image by default
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.

Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.

The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-28 01:16:00 +02:00
Christian Marangi
c4a9a67de8
ipq806x: disable ea8500 image by default
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.

Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.

The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-28 01:10:21 +02:00
Rafał Miłecki
ae57770c95 bcm4908: add pending BQL support for bcm4908_enet
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-27 22:34:00 +02:00
Rafał Miłecki
31e4e56654 bcm4908: backport bcm4908_enet fix for NULL dereference
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-27 21:14:02 +02:00
Rafał Miłecki
6a02205a4d bcm4908: optimize Ethernet driver by using build_skb()
This should slightly improve performance thanks to the better cache
usage.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-27 18:59:46 +02:00
Jan Hoffmann
eb456aedfe realtek: use assisted learning on CPU port
L2 learning on the CPU port is currently not consistently configured and
relies on the default configuration of the device. On RTL83xx, it is
disabled for packets transmitted with a TX header, as hardware learning
corrupts the forwarding table otherwise. As a result, unneeded flooding
of traffic for the CPU port can already happen on some devices now. It
is also likely that similar issues exist on RTL93xx, which doesn't have
a field to disable learning in the TX header.

To address this, disable hardware learning for the CPU port globally on
all devices. Instead, enable assisted learning to let DSA write FDB
entries to the switch.

For now, this does not sync local/bridge entries to the switch. However,
support for that was added in Linux 5.14, so the next switch to a newer
kernel version is going to fix this.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-26 09:59:38 +02:00
Jan Hoffmann
2088e440b1 realtek: set up L2 table entries properly
Initialize the data structure using memset to avoid the possibility of
writing garbage values to the hardware.

Always set a valid entry type, which should fix writing unicast entries
on RTL930x.

For unicast entries, set the is_static flag to prevent the switch from
aging them out.

Also set the rvid field for unicast entries. This is not strictly
necessary, as the switch fills it in automatically from a non-zero vid.
However, this makes the code consistent with multicast entry setup.

While at it, reorder the statements and fix some style issues (double
space, comma instead of semicolon at end of statement). Also remove the
unneeded priv parameter and debug print for the multicast entry setup
function.

Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-26 09:59:24 +02:00
Christian Marangi
a31b598590
realtek: 5.10: refresh kernel patches
Refresh kernel patches for realtek 5.10 kernel

Refreshed patch:
- 300-mips-add-rtl838x-platform.patch

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 04:56:16 +02:00
Davide Fioravanti
8d921167e9
ipq40xx: convert to DSA and enable Netgear Orbi devices
Convert to DSA and enable again Netgear Orbi devices:
 - RBR50
 - RBS50
 - SRR60
 - SRS60

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-10-25 02:34:46 +02:00
Christian Marangi
ea63945b25
generic: 5.15: add missing CMDLINE_OVERRIDE patch
This patch was wrongly dropped with the assumption that it was moved to
generic. This wasn't the case and caused the malfunction of the Asrock
G10 router.

Reintroduce it to fix Asrock G10 functionality.

Fixes: 8cc2caed58 ("ipq806x: 5:15: add testing kernel version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:45 +02:00
Christian Marangi
1c514f05ab
ipq806x: 5.15: drop mmc-ddr-1_8v from sdcc1 node
Zyxel NGB6817 is the only router that use mmc for rootfs. Upstream
kernel dtsi have mmc-ddr-1_8v enabled for sddc1. This is wrong as mmc on
ipq806x is supplied by a fixed 3.3v regulator and can't operate at 1.8v.
This cause the sddc1 to malfunction and cause kernel panic.
In old 5.15 version this was disabled but it was put in addition to many
other changes so it was dropped silently. Restore this patch to fix
working condition of such router.

Fixes: 88bf652 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Fixes: #11000
Tested-by: Hendrik Koerner <koerhen@web.de>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:45 +02:00
Christian Marangi
a87b6cda02
ipq806x: 5.15: revert unwanted DSA conversion for ASRock G10
In refreshing DTS to the upstream version an unwanted change slipped in
the commit. The ASRock G10 dts got converted to DSA without any support.

Revert this to swconfig driver to restore normal functionality.

Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:45 +02:00
Christian Marangi
dd2515cb53
ipq806x: 5.15: backport qcom_nandc patch for unprotected spare data fix
We currently ignore ret of the nandc partition parser if unprotected
spare data is true. This is the case for ipq806x nand.

Backport patch that fix this error and correctly handle error from
partition parser.

Fixes: ae6a63bc97 ("ipq806x: 5.15: replace nandc patch with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:44 +02:00
Christian Marangi
04a8944178
generic: 5.15: backport smempart parser fixup patch with EPROBE_DEFER error
Backport patch from kernel 5.15 that mute error on EPROBE_DEFER with
smempart parser.

This parser require the smem device to be probed first and currently it
may happen that mtd gets probed before the smem device causing an error
on the smempart parser. This error may be confusing and should be muted.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:44 +02:00
Christian Marangi
221020fda6
generic: 5.15: backport qcom smem patch for reserved-space support
In new kernel version from 5.16, smem node can be declared directly in
the reserved-space node. Upstream ipq806x (and to-be-merged) ipq807x
allign to this new implementation. Backport this patch to kernel 5.15 to
fix support for smem parser for ipq806x target.

Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:43 +02:00
Christian Marangi
ffe91ca478
generic: 5.15: move not backport patch to pending dir
Move patch wrongly placed in backport dir to pending dir as they still
didn't got merged upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:48 +02:00
Christian Marangi
2a7bdde29b
generic: 5.15: move MGLRU patches from pending to backport
Move MGLRU patches from pending to backport as they got merged upstream.
These are direct porting from one of the dev so it's better to just move
than trying to backport them again from upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:48 +02:00
Christian Marangi
ccedd7175d
generic: 5.15: move mvebu aardvark patch from pending to backport
Move mvebu aardvark patch from pending to backport as they got merged
upstream.
One additional patch is needed as a later fixup for it.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:47 +02:00
Christian Marangi
08c6c0c217
generic: 5.15: move ZTE MF286D modem patch from pending to backport
Move ZTE MF286D modem patch from pending to backport as it was merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:47 +02:00
Christian Marangi
e25890ce45
generic: 5.15: move bluetooth mt79 usb id patch from pending to backport
Move bluetooth mt79 usb id patch from pending to backport as it got
merged upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:47 +02:00
Christian Marangi
a1522ec156
generic: 5.15: move mtk eth soc patch from pending to backport
Move mtk eth soc patch from pending to backport as it got merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:46 +02:00
Christian Marangi
d7a6e171c0
generic: 5.15: move sfp HALNy patch from pending to backport
Move sfp HALNy patch from pending to backport as they got merged
upstream. The patch was reordered and one was squashed in the upstream
variant.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:46 +02:00
Christian Marangi
90629d82da
generic: 5.15: move pending xtx nand patch from pending to backport
Move pending xtx nand patch from pending to backport as it got merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:46 +02:00
Christian Marangi
f846945bd2
generic: 5.15: move dtc drop interrupt check from pending to backport
Move dtc drop interrupto check from pending to backport as it got merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:46 +02:00
Christian Marangi
b182634689
generic: 5.15: move MIPS cpuinfo patch from pending to backport
Move MIPS cpuinfo patch from pending to backport as it got merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:45 +02:00
Shiji Yang
288b36c2ea ramips: add missing WAN LED for Xiaomi Mi Router 4A / 4C
The blue WAN LED connected to GPIO37 is missing, so re-add it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-10-23 23:33:22 +02:00
Sander Vanheule
9f6cbc78cd realtek: consistently flood RMA frames
The switches support different actions for incoming ethernet multicast
frames with Reserved Multicast Addresses (01-80-C2-00-00-{01-2F}). The
current code will set the 2-bit action field to FLOOD (0x3) for most
classes, but the highest bit is always unset for the relevant control
registers. This means the DROP (0x1) action being used for these
classes; whatever class the MSB happens to be in.

For RTL838x, this results in {20,23-2F} frames being dropped, instead of
flooding all ports. On other switch generations, {0F,1F,2F} frames are
dropped. This is inconsistent, and appears to be a mistake. Remove this
inconsistency by flooding all multicast frames with RMA addresses.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Sander Vanheule
039e5be4af realtek: remove RTL839x path in RTL838x multicast
The multicast setup function rtl838x_eth_set_multicast_list() checks if
the current SoC is a RTL839x family device. However, the function is
only included in the RTL838x ops table, so this path should never be
taken, making this dead code. rtl839x_eth_set_multicast_list() is
already present in the RTL839x ops table, so it should be safe to remove
this branch.

While touching the code, also re-sort the functions to match sorting
elsewhere, with rtl838x coming before rtl839x.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Jan Hoffmann
19b86658b7 realtek: reduce excessive logging for FDB operations
Currently several messages at KERN_INFO level are printed for every FDB
del/dump operation. This can cause a significant slowdown for example
while using "bridge fdb", and may even trigger a watchdog.

Remove most of these log messages, as the new L2 table debugfs node
should be a good replacement. Change the remaining messages to
KERN_DEBUG level.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-23 22:33:08 +02:00
Jan Hoffmann
ae9487c535 realtek: add debugfs node for L2 table
This allows to view all unicast and multicast entries that are currently
in the L2 hash table and the CAM.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-23 22:33:08 +02:00
Jan Hoffmann
4657a5301e realtek: avoid busy waiting for RTL839x PHY read/write
Switch to a polling implementation similar to the one for RTL838x, to
allow other kernel tasks to run while waiting.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
b295c7140b realtek: disable otto timer for RTL93xx targets
The new timer is not yet ready for all targets. Avoid interactive
questions during build

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[rename symbol to CONFIG_REALTEK_OTTO_TIMER]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
beb5b07943 realtek: timer driver: activate for RTL839X devices
Use the	new timer driver for the RTL839X devices and remove the
no longer needed modules.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
ec675fb744 realtek: timer driver: activate for RTL838X devices
Use the new timer driver for the RTL838X devices. Remove the no
longer needed modules.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
5c677b2298 realtek: timer driver: documentation
Provide some helpful information about the devicetree configuration of
our new driver

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct compatible order in examples]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
3cc8011171 realtek: resurrect timer driver
Now that we provide a clock driver for the Reltek SOCs the CPU frequency might
change on demand. This has direct visible effects during operation

- the CEVT 4K timer is no longer a stable clocksource
- after CPU frequencies changes time calculation works wrong
- sched_clock falls back to kernel default interval (100 Hz)
- timestamps in dmesg have only 2 digits left

[    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps ...
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.080000] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.090000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ...

Looking around where we can start the CEVT timer for RTL930X is a good basis.
Initially it was developed as a clocksource driver for the broken timer in that
specific SOC series. Afterwards it was shifted around to the CEVT location,
got SMP enablement and lost its clocksource feature. So we at least have
something to copy from. As the timers on these devices are well understood
the implementation follows this way:

- leave the RTL930X implementation as is
- provide a new driver for RTL83XX devices only
- swap RTL930X driver at a later time

Like the clock driver this patch contains a self contained module that is SOC
independet and already provides full support for the RTL838X, RTL839X and
RTL930X devices. Some of the new (or reestablished) features are:

- simplified initialization routines
- SMP setup with CPU hotplug framework
- derived from LXB clock speed
- supplied clocksource
- dedicated register functions for better readability
- documentation about some caveats

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[remove unused header includes, remove old CONFIG_MIPS dependency, add
REALTEK_ prefix to driver symbol]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Brian Norris
a3da858ab0 ipq40xx: Convert Google Wifi to DSA, reenable
Undo parts of these:

116feb4a1c ipq40xx: remove non-converted network configs
db19efee95 ipq40xx: disable boards not converted to DSA

Reintroduce the DT paths /soc/edma@c080000/gmac{0,1}, because the stock
bootloader has memorized them (instead of following aliases); then plug
the MAC address back in via 05_set_iface_mac_ipq40xx.sh, since the
'local-mac-address' property is no longer in the correct node.

Cc: David Bauer <mail@david-bauer.net>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2022-10-23 08:27:40 +02:00
Jack Chen
57577bb8cc ipq40xx: convert to DSA and enable mobipromo,cm520-79f
Convert to DSA and enable the MobiPromo CM520-79F device again.

Signed-off-by: Jack Chen <redchenjs@live.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2022-10-23 01:45:52 +02:00
Pavel Kamaev
a716ac5564 ath79: fix reference clock for RouterBoard 912UAG
This fixes reference clock frequency of RB912. 25 MHz frequency leads
to system clock running too fast, uptime incrementing too fast and
delays (like `sleep 10`) returning too early.

Board has quartz with NSK 3KHAA Z 40 000 marking.

Signed-off-by: Pavel Kamaev <pavel@kamaev.me>
2022-10-23 01:45:52 +02:00
David Bentham
67660d3667 ramips: fix WAN mac address allocation for Unielec 01 and 06 models
Manufacturer has predetermined mac address values for lan and wan ports.

This change keeps inline with other mt7621 devices mac address allocation
from factory mtd partition.

Example from hexdump output:

0xe000 0x6 (lan) -           0xe006 0x6 (wan)

0000e000  70 b3 d5 10 02 96 70 b3  d5 10 02 95 ff ff ff ff

Previous change had created an overlapping mac address situation as it
would increment by one based on the lan mac address location found in the
factory partition, which would sometimes increment to the same as the
mt7603 wifi chip.

Tested on Unielec u7621-01 model

Signed-off-by: David Bentham <db260179@gmail.com>
2022-10-23 01:45:52 +02:00
Robert Senderek
ac296f6210 ramips: rt3883: enable lzma-loader for Belkin F9K1109v1
Fixes boot loader LZMA decompression issues

Fixes: #10968
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
2022-10-23 01:45:52 +02:00
Alex Khodin
f6099d7974 ramips: mt7621: enable lzma-loader for Asus RT-N56U-B1
Fixes boot loader LZMA decompression issues.

Without this change the board end up in a boot loop.

Signed-off-by: Alex Khodin <mxktz1@gmail.com>
2022-10-23 01:45:52 +02:00
Chukun Pan
4f9b360f0b ramips: add A-040W-Q alternative name for MSG1500 X.00
The hardware of Nokia A-040W-Q and RAISECOM MSG1500 X.00 are
exactly the same, both of which are customized by operators.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-23 01:45:52 +02:00
Chukun Pan
7b863af180 kernel: move mac-address-ascii patches to generic
This enables other targets to use the mac-address-ascii
feature.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-23 01:45:52 +02:00
Aleksander Jan Bajkowski
802ca492d8 lantiq: add 6.1 tag to upstream patch
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-23 01:45:52 +02:00
Martin Blumenstingl
d4571e98ab lantiq: Add Linux 5.15 as testing kernel version
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-10-22 19:44:46 +02:00
Martin Blumenstingl
d374e0346e lantiq: 5.15: refresh patches
0001-MIPS-lantiq-add-pcie-driver.patch needs to drop
MODULE_SUPPORTED_DEVICE because that macro is gone on newer kernels.

Add checks for copy_{to,from}_user in
0008-MIPS-lantiq-backport-old-timer-code.patch which is now mandatory.

0705-v5.13-net-dsa-lantiq-allow-to-use-all-GPHYs-on-xRX300-and-.patch
get dropped because it's a backport from Linux 5.13.

All other patches are refreshed.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-10-22 19:44:45 +02:00
Martin Blumenstingl
c783073894 lantiq: copy Linux 5.10 files in preparation for Linux 5.15 support
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-10-22 19:44:45 +02:00
Chen Minqiang
3505933073 ipq40xx: convert to DSA and enable asus,rt-ac42u
This convert board asus,rt-ac42u to DSA and re-enable it

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2022-10-22 20:09:58 +08:00
Hauke Mehrtens
1ea3510c5c kernel: Add missing kernel configuration options
The at91/sam9x targets misses these configuration options when using
kernel 5.15.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
0a00189e41 at91: kernel v5.15: use KERNEL_TESTING_PATCHVER:=5.15
Use KERNEL_TESTING_PATCHVER:=15 for at91 targets.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
dd37b205f8 at91: kernel v5.10: refresh configs
Refresh kernel v5.10 configs.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
fe7e34d793 at91: kernel v5.15: refresh configs
Refresh kernel v5.15 configs.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
d0d7771262 at91: kernel v5.15: remove upstreamed patches
Remove patches that are now integrated in kernel v5.15.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
eb758a8fec at91: kernel v5.15: copy config and patches from 5.10
Copy kernel config and patches from 5.10. Along with it
individual targets' config-default from 5.10 has been moved to
config-5.10.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Daniel Golle
c5c37886cf oxnas: shuttle-kd20: fix thermal zone
Fix typo ('_' vs '-') and add #cooling-cells to gpio-fan to get
thermal zone into functional state.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-21 20:57:53 +01:00
Daniel Golle
63ff5b783d oxnas: switch to Linux 5.15 and drop Linux 5.10
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-21 20:57:53 +01:00
Aleksander Jan Bajkowski
9226f1e419
kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic config
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.

Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....

Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
  If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
  option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
  the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC -  enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-21 13:47:01 +02:00
Aleksander Jan Bajkowski
069bda0adb
lantiq: add rgmii delays on BT Home Hub 5A
This comit fixes warnings that occur on kernel 5.15:
...
[    2.269736] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 1e108000.switch-mii:00:
               PHY has delays (e.g. via pin strapping), but phy-mode = 'rgmii'
[    2.269736] Should be 'rgmii-id' to use internal delays txskew:1500 ps rxskew:1500 ps
...

Ref: be393dd685
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-21 13:45:37 +02:00
Linus Walleij
e629ced778 bcm53xx: only fixup seama on D-Link DIR-885L
Just one device builds seama images so let's just fix up
seama on that one device. I guess the tool errors out but
this feels cleaner.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[rmilecki: drop "fixtrx" from D-Link case]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-21 08:54:34 +02:00
Arınç ÜNAL
2b9bb5b187 bcm53xx: enable Broadcom 4366b1 firmware for Asus RT-AC88U
On some of the hardware revisions of Asus RT-AC88U, brcmfmac detects the
4366b1 wireless chip and tries to load the firmware file which doesn't
exist because it's not included in the image.

Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-10-21 08:50:51 +02:00
Daniel Golle
c15e7e2910
mediatek: filogic: consolidate adc '32k' clock
Add dependency to '32k' ADC clock so it is always enabled for thermal
and raw access to ADC values. This allows to remove the patch for the
ADC driver and reduce the patch adding thermal support for MT7986 to
only add the new efuse layout and temperature decoding for V3.

Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-20 20:37:50 +01:00
Petr Štetiar
ae76c978c9 pistachio: refresh kernel patches
Refresh dirty patches after commit 711f1a8bcb ("kernel: mtd: backport
SafeLoader parser").

Fixes: 711f1a8bcb ("kernel: mtd: backport SafeLoader parser")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-20 09:53:23 +02:00
Petr Štetiar
329b583aad ath79: refresh kernel patches
Refresh dirty patches after commit 711f1a8bcb ("kernel: mtd: backport
SafeLoader parser").

Fixes: 711f1a8bcb ("kernel: mtd: backport SafeLoader parser")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-20 09:53:23 +02:00
John Audia
b1cc4eac1b
mt7622: switch default CPU governor to ondemand
The most common CPU governor in the OpenWRT project is currently ondemand (see
below).  Switch mt7622 over to it as well.

Audit the code by running the following and then analyzing the results:
find -name 'config-5.*' -print0 | xargs -0 grep 'CONFIG_CPU_FREQ_DEFAULT_GOV.*=y'

ondemand: 16
performance: 5
schedutil: 5
userspace: 2

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-10-20 00:44:53 +02:00
Daniel Golle
f2ae4e2f8c
mediatek: clean up platform kernel modules
Remove kmod-sdhci-mtk as the mtk-sd driver is built-in anyway for the
relevant subtargets in order to support mounting rootfs from eMMC or
SD card.

Add kmod-iio-mt6577-auxadc to support reading the raw values from the
auxadc unit used as in-SoC thermal sensor. This driver was previously
built-in, but as thermal itself works well without it there is no use
for it in every day use of a device. Build the module to still allow
access to the raw values for those who need it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-19 23:20:48 +01:00
Andrey Butirsky
47d58afbdf ramips: kndrt31r19: set up wan interface by default
The only WAN port of the device is it's modem, so set it up as such

Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-10-19 23:00:40 +02:00
Mark Mentovai
9a8e008188 ipq40xx: Convert mikrotik,wap-ac to DSA
As done previously, this preserves the MAC addresses of they physical
Ethernet ports. The interfaces are renamed as eth0 is in use for the
native GMAC; the new interface naming matches the physical port labels.
 - sw-eth1 corresponds to the physical port labeled ETH1 and has the
   base MAC address. This port can be used to power the device.
 - sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC
   address one greater than the base.

As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.

Signed-off-by: Mark Mentovai <mark@mentovai.com>
2022-10-19 22:58:12 +02:00
INAGAKI Hiroshi
48bb71ff28 ath79: improve MAC address configuration of ELECOM devices
Get MAC address of WAN from HW.WAN.MAC.Address in hwconfig partition
instead of calculated one from wlan's address.
And added label_mac.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-19 22:58:12 +02:00
INAGAKI Hiroshi
961d4230f4 ath79: use NVMEM for wlan caldata on ELECOM devices
Use NVMEM "calibration" implementation for ath9k/ath10k(-ct) on ELECOM
WRC-300GHBK2-I and WRC-1750GHBK2-I/C instead of mtd-cal-data property
or user-space script.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-19 22:58:12 +02:00
INAGAKI Hiroshi
2e1ffc3412 ath79: use ARTIFACTS for initramfs-factory of ELECOM devices
Use ARTIFACTS to generate factory image of the following ELECOM devices
instead of redundant recipe which generate on KERNEL_INITRAMFS.

- ELECOM WRC-300GHBK2-I
- ELECOM WRC-1750GHBK2-I/C

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-19 22:58:12 +02:00
INAGAKI Hiroshi
00ddd29b65 build: move Build/edimax-header to image-commands.mk
To use from the following devices in ath79 target, move edimax-header to
image-commands.mk.

- ELECOM WRC-300GHBK2-I
- ELECOM WRC-1750GHBK2-I/C

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-19 22:58:12 +02:00
Nick Hainke
fdd605581c x86: switch to 5.15 as default kernel
Set 5.15 as default kernel. Testing support was already added on
29.03.2021.

Testing support was added in
9b3bc5d119 ("x86: enable 5.15 as testing kernel").

[0] - edd6021465

Tested-by: Mark Mentovai <mark@mentovai.com>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-10-19 21:40:23 +02:00
Daniel Golle
d640cbac0e
mediatek: mt7622: don't rely on existing image for sysupgrade
Don't reply on mapped rootfs partition but rather just take what ever
has been set to the kernel cmdline root= parameter as a hint to decide
which media to install sysupgrade to on the BananaPi BPi-R64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-19 20:05:17 +01:00
Daniel Golle
a97991fbeb
mediatek: mt7622: kernel config fixes
* remove orphaned Kconfig symbol now that CONFIG_IIO is no longer
   selected after commit ef8b935c95 ("mediatek: clean up mt7622 kernel config")

 * select UBI fast-map feature to decrease boot time and keep the
   number of spare blocks required in sync with U-Boot's expectations
   (we got fast-map enabled in U-Boot)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-19 20:05:12 +01:00
Daniel Golle
dca5bf6d53
mediatek: update pending and rename merged patch
Add patch headers and description for pending patch.
Add version tag to patch already merged upstream.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-19 20:05:01 +01:00
Rafał Miłecki
711f1a8bcb kernel: mtd: backport SafeLoader parser
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-19 07:07:14 +02:00
Rafał Miłecki
4eda414b09 kernel: mtd: backport extended dynamic partitions support
This gets rid of "nvmem-cells" limitation. Dynamic partitions can be
defined for any (sub)partitions layout.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-19 07:07:14 +02:00
Rafał Miłecki
76a470d5df kernel: mtd: fix unbalanced of_node_put() in dynamic partitions code
Fixes: 1a9ee36734 ("kernel: backport mtd dynamic partition patch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-19 07:07:14 +02:00
Christian Marangi
d80c91b23e
generic: 5.15: add missing tag for some backports patches
Add for mtd-parsers-trx-allow-to-use-on-MediaTek-MIPS-SoCs.patch and
hwmon-lm70-Add-ti-tmp125-support.patch the 5.18 tag as it was merged
in kernel 5.18.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-18 22:45:08 +02:00
Christian Marangi
4611fdd759
ipq806x: 5.15: add 6.1 tag to upstream patch
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-18 22:21:04 +02:00
Daniel Golle
de94587e70
mediatek: filogic: don't rely on image preset in flash or sysupgrade
Instead of trying to figure out the actual root device, just use the
kernel 'root' cmdline parameter as a hint to decide which device to
flash to.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-18 20:08:47 +01:00
Daniel Golle
51ee5fb274
mediatek: filogic: use UBI fast map to speed up boot
Use UBI fast map feature to avoid scanning the whole flash on each
boot which takes several seconds.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-18 20:08:30 +01:00
Daniel Golle
b00640bd06
mediatek: don't break auxadc without 32k clk
Make the newly added 32k clock optional for the auxadc driver also used
on pre-filogic platforms.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-18 20:08:25 +01:00
Petr Štetiar
b63d6d4730 mt7621: hiwifi_hc5962: fix reboot loop by using LZMA loader
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

References: https://github.com/openwrt/openwrt/issues/10645#issuecomment-1282607274
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-18 19:05:06 +02:00
Josef Schlehofer
ed0dd05bfd kernel: add missing config symbols for 5.15
When I enabled CONFIG_HOTPLUG_PCI for mvebu platform, it was asking for
more symbols.

Fixes:
Support for PCI Hotplug (HOTPLUG_PCI) [Y/?] y
  CompactPCI Hotplug driver (HOTPLUG_PCI_CPCI) [N/y/?] n
  SHPC PCI Hotplug driver (HOTPLUG_PCI_SHPC) [N/y/?] (NEW)

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-10-18 15:09:23 +02:00
John Audia
b0a94fc60d kernel: bump 5.15 to 5.15.74
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-18 15:09:23 +02:00
Petr Štetiar
7dd1cab1c1 mt7621: netgear_ex6150: fix reboot loop by using LZMA loader
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

Fixes: #10645
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-18 09:01:39 +02:00
Christian Marangi
1b147bec1a
ipq806x: 5.15: refresh target patches
Refresh ipq806x target patches for kernel 5.15.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-17 00:40:16 +02:00
Christian Marangi
32ecf4251a
bcm53xx: 5.10: refresh target patches
Refresh bcm53xx target patches for kernel 5.10.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-17 00:34:28 +02:00
Christian Marangi
32c683ddce
generic: 5.10: refresh hack patches
Refresh hack patches for kernel 5.10.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-16 20:36:49 +02:00
Christian Marangi
6b4bdab918
generic: 5.10: refresh backport patches
Refresh backport patches for kernel 5.10.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-16 20:36:03 +02:00
Christian Marangi
6893dd4803
generic: 5.15: refresh hack patches
Refresh hack patches for kernel 5.15.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-16 13:19:33 +02:00
Christian Marangi
fb67733d87
generic: 5.15: refresh backport patches
Refresh backport patches for kernel 5.15.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-16 13:19:05 +02:00
David Bauer
f8942d1428 mpc85xx: fix unset kernel symbol
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-10-14 23:13:02 +02:00
Matthias Schiffer
2fa53c9214 mpc85xx: p1010: make TP-Link WDR4900 v1 build again
Add the spi-loader as a pre-kernel stage, so we can lift the kernel size
limit.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2022-10-14 23:13:02 +02:00
Matthias Schiffer
a296055b82 mpc85xx: add SPI kernel loader for TP-Link TL-WDR4900 v1
Similar to the lzma-loader on our MIPS targets, the spi-loader acts as
a second-stage loader that will then load and start the actual kernel.
As the TL-WDR4900 uses SPI-NOR and the P1010 family does not have support
for memory mapping of this type of flash, this loader needs to contain a
basic driver for the FSL ESPI controller.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2022-10-14 23:13:02 +02:00
Christian Marangi
fcff86be06
generic: 5.15: backport qca8k fixup patches for Big-Endian systems
Backport qca8k fixup patches for inband mgmt on Big-Endian systems.
This is needed for ath79 and mpc85xx targets that are Big-Endian and use
qca8k based switch.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-14 15:10:52 +02:00
Bruno Umuarama
85ae64bb27
mediatek: mt7623: fix thermal zone
Raising the temperatures for passive and active trips. @VA1DER
proposed at issue 9396 to remove passive trip. This commit relates to
his suggestion.

Without this patch. the CPU will be throttled all the way down to 98MHz
if the temperature rises even a degree above the trip point, and it was
further discovered that if the internal temperature of the device is
above the first trip point temperature when it boots then it will start
in a throttled state and even
$ echo disabled > /sys/class/thermal/thermal_zone0/mode
will have no effect.

The patch increases the passive trip point and active cooling map. The
throttling temperature will then be at 77°C and 82°C, which is still a
low enough temperature for ARM devices to not be in the real danger
zone, and gives some operational headroom.

Signed-off-by: Bruno Umuarama <anonimou_eu@hotmail.com>
2022-10-14 14:44:37 +02:00
Felix Fietkau
ef8b935c95 mediatek: clean up mt7622 kernel config
Remove a few unused options to reduce kernel size

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-10-14 13:16:16 +02:00
Felix Fietkau
9995dd2543 kernel: remove target specific CONFIG_IKCONFIG lines
Use generic configuration for this feature

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-10-14 13:15:47 +02:00
Felix Fietkau
d3cd09d1c6 kernel: add missing lockdep config symbols for 5.15
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-10-14 13:15:29 +02:00
Felix Fietkau
34054e4c06 mediatek: fill wlan device entries in board.json on mt7622
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-10-14 13:13:49 +02:00
Nick Hainke
dbce336539
airoha: fix imagebuilder generation by introducing generic target
The generic imagebuilder does not have a generic in the name, although
this is the default naming scheme. Apply the same fix as for the octeon
target. Thanks to @dangowrt for reporting that the same issues applies
also for the airoha target.

Before the fix:
openwrt-imagebuilder-airoha.Linux-x86_64.tar.xz

After:
openwrt-imagebuilder-airoha-generic.Linux-x86_64.tar.xz

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-10-13 17:38:59 +02:00
Aleksey Nasibulin
3413409ef6
bcm53xx: linksys ea6500-v2: extend RAM to full 256MB
Linksys ea6500-v2 have 256MB of ram. Currently we only use 128MB.
Expand the definition to use all the available RAM.

Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
[ wrap to 80 columns ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-13 16:34:50 +02:00
Olliver Schinagl
41a1a652fb
kernel: backport gnu11 upgrade
Upstream has switched to gnu11 not too long ago. One advantage of
backporting this to these older kernels is, that we can encourage and
write better upstreamable kernels. E.g. the kernel devs prefer loop
declarations. Shrinking the master/local gap will be useful in these
cases.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-13 16:03:35 +02:00
Giammarco Marzano
cd93980abb
ipq40xx: Fix wrong GPIO for internal status LED on ZTE MF289F
Change GPIO from 10 to 35 to make it works as expected

Fixes: 0de6a3339f ("ipq40xx: Add ZTE MF289F")
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2022-10-12 00:59:39 +02:00
Christian Marangi
bb451eccaa
ipq806x: switch to 5.15 kernel by default
Switch to 5.15 kernel by default to promote more wider testing and use
better upstream patch.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:46 +02:00
Christian Marangi
8d9dfac2bd
ipq806x: 5.15: add clk krait fixes/improvement patch
Add various krait fixes patch that correctly bringup mux and cpu clocks.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:46 +02:00
Christian Marangi
ecf1abe5bf
ipq806x: 5.15: enable again usb node for each device
Usb node now are disabled by default in dtsi. Enable again them in each
device dts.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:46 +02:00
Christian Marangi
6f1b89baba
ipq806x: 5.15: add krait-cc modernization patch and fixup
Add multiple patch for krait-cc modernization and multiple fixup for the
driver. Also modify a patch to enable the qsb fixed clock and add pxo to
krait-cc node.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:45 +02:00
Christian Marangi
e5a3720a56
ipq806x: 5.15: add krait clock modernization patch
Backport krait clock modernization patch.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:45 +02:00
Christian Marangi
a7c7a3c009
ipq806x: 5.15: backport qcom clk fixes for krait and hfpll
Backport some qcom clock fixes for krait and hfpll driver.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:45 +02:00
Christian Marangi
78fef3cc6f
ipq806x: 5.15: renumber tsens patch with new order
Renumber tsens patch with new order for consistency.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:44 +02:00
Christian Marangi
8392a6b395
ipq806x: 5.15: enable new devfreq scaling driver in config
Enable new devfreq scaling driver in kernel config.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:44 +02:00
Christian Marangi
9254ed0f3b
ipq806x: 5.15: rework nand_pins for wg2600hp3 dts
nand_pins definition is now shipped in ipq8064 dtsi. Rework the
nand_pins definition for wg2600hp3 5.15 files.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:44 +02:00
Christian Marangi
6134ba4a34
ipq806x: 5.15: add boot-partitions binding to fix block warning
The patch has changed implementation and now the binding has changed.
Replace the old binding with boot-partitions and reimplement the
definition with the new definition.
The new definition is:
<offset1 size1 offset2 size2 offset3 ...>
and now supports sparsed patch.

Also add missing binding in some dts and add the backup boot partition
to the boot-partitions list.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:44 +02:00
Christian Marangi
900542698c
ipq806x: 5.15: remove useless spm patch
Remove useless spm patch as using the normal qcom,spm compatible is
enough to register it with no clks.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:43 +02:00
Christian Marangi
ae6a63bc97
ipq806x: 5.15: replace nandc patch with upstream version
Replace nandc fix patch with upstream version.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:43 +02:00
Christian Marangi
a8d7aed033
ipq806x: 5.15: replace fab scaling patch with devfreq driver
Replace fab scaling patch with devfreq driver.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:43 +02:00
Christian Marangi
25aa65304c
ipq806x: 5.15: add new version of cache cpu scaling driver
Use a new implementation by using a devfreq driver to scale the shared
cache of the krait cpu cores.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:42 +02:00
Christian Marangi
3a911b8c2d
ipq806x: 5.15: backport devfreq new cpufreq based PASSIVE governor
Backport devfreq new cpufreq based PASSIVE governor needed for devfreq
based fab and cache scaling.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:42 +02:00
Christian Marangi
5ad826f48a
ipq806x: 5.15: replace stmmac pcs fix with upstream version
Replace stmmac pcs fix with upstream version.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:42 +02:00
Christian Marangi
cd619eeff2
ipq806x: 5.15: replace gcc fixes with upstream version
Replace gcc patch fixes with upstream version.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:41 +02:00
Christian Marangi
61a2bedf79
ipq806x: 5.15: replace lcc patch with upstream version
Replace lcc patch with proposed upstream version.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:41 +02:00
Christian Marangi
88bf652525
ipq806x: 5.15: replace dtsi patches with upstream version
Reorganize dtsi patches with upstream version and drop dtsi in 5.15
files.
Also add an additional upstream patch for hwspinlock support.
Refresh all the dts with needed changes.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:41 +02:00
Christian Marangi
bd02eb7502
ipq806x: 5.15: remove PCI_DOMAINS patch not needed anymore
This doesn't cause any panic anymore and no regression are observed with
ath10k. Remove this additional patch.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:40 +02:00
Christian Marangi
f2dc002495
ipq806x: 5.15: remove qcom adm Documentation patch
Remove qcom adm Documentation patch that is not needed for the target.
Probably a leftover when the adm bus was added, now merged upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:40 +02:00
Christian Marangi
faa79f97b6
ipq806x: split files dir to 5.10 and 5.15
In preparation for a cleanup of 5.15 patches copy the files dir to 5.10
and 5.15 kernel version.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-11 21:28:37 +02:00
Martin Blumenstingl
2683cca592 lantiq: dts: vr9: Add missing properties to the CPU port on the switch
The CPU port should define the phy-mode and and a PHY phandle or
fixed-link to indicate how the CPU port is connected to the SoC's
Ethernet controller. On xRX200 this is all internal connection, so use
phy-mode = "internal" along with a fixed-link that matches the
definition inside &eth0.

Linux 6.0 shows a warning since upstream commit e09e9873152e3f ("net:
dsa: make phylink-related OF properties mandatory on DSA and CPU
ports"). when these properties are missing. Adding the properties
before OpenWrt is updated to Linux 6.0 is harmless.

Suggested-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-10-10 21:51:05 +02:00
Du Cai
8ac69159f2 ramips: use lzma-loader on JCG Q20
Fixes the LZMA uncompression issue on JCG Q20.

Signed-off-by: Du Cai <caidu@smail.nju.edu.cn>
2022-10-09 22:50:57 +02:00
INAGAKI Hiroshi
32e41ba18a ipq40xx: convert to DSA and enable Sony NCP-HG100/Cellular
This patch converts networking on Sony NCP-HG100/Cellular to DSA and
re-enables support for the device.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-09 22:45:06 +02:00
Dirk Buchwalder
579ea6b970 ipq40xx: ZTE MF289F: convert to DSA
Convert ZTE MF289F device to DSA, re-order network ports to match the
labels on the case and re-enable the device.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
2022-10-09 22:39:48 +02:00
John Audia
9110126620 kernel: bump 5.15 to 5.15.72
Removed upstreamed:
  generic/pending-5.15/722-net-mt7531-only-do-PLL-once-after-the-reset.patch[1]
  bcm53xx/patches-5.15/082-v6.0-clk-iproc-Do-not-rely-on-node-name-for-correct-PLL-s.patch[2]

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72
Run-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72 (RB5009UG+S+IN)

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=5de02ab84aeca765da0e4d8e999af35325ac67c2
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=ab5c5787ab5ecdc4a7ea20b4ef542579e1beb49d

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-09 22:26:16 +02:00
John Audia
e2da6a0a59 kernel: bump 5.10 to 5.10.147
Removed upstreamed:
  bcm53xx/patches-5.10/083-v6.0-clk-iproc-Do-not-rely-on-node-name-for-correct-PLL-s.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.147&id=a8e6cde5062fb2aff81f86cc0770591714bee545

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-09 22:18:24 +02:00
Daniel Golle
88eae0f036
mediatek: filogic: set correct PWM clock and clean thermal zone
* set correct clocks for PWM to work.
 * MT7986 PWM does have the 26MHz-clock-select, set that in patch
 * drop useless 'passive' trip point in thermal zone
 * extend pwm-fan to have 3 active operating points
 * set reasonable trip points in thermal zone
 * invert pwm-fan operating points and set shorter period to allow
   less noisy operation of the PWM fan of the BPi-R3.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-09 16:41:16 +01:00
INAGAKI Hiroshi
629f2de1a7 realtek: cleanup rtl83{8x,9x}_enable_learning/flood
In *_enable_learning() only address learning should be configured, so
remove enabling forwarding. Forwarding is configured by the respective
*_enable_flood() functions.

Clean up both functions for RTL838x and RTL839x, and fix the comment on
the number of entries.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[squash RTL838x, RTL839x changes]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-08 11:05:03 +02:00
INAGAKI Hiroshi
b11b56e8a8 realtek: swap *_phylink_mac_link_down() contents
Fix the (accidentally?) swapped contents of
rtl83xx_phylink_mac_link_down() and rtl93xx_phylink_mac_link_down().

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amend commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-08 11:05:02 +02:00
INAGAKI Hiroshi
ff307f52f5 realtek: fix place of fdb/mdb info messages
Those messages should be printed when entry was found (idx >= 0). Move
them to the right place to not print invalid entry indices.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amden commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-08 11:05:02 +02:00
INAGAKI Hiroshi
3834e72fa3 realtek: add missing of.h include in phy driver
of.h is required for of_property_read_u32().

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amend commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-08 11:05:02 +02:00
INAGAKI Hiroshi
04cca345df realtek: fix use of uninitialized sds_mode
The initial state of sds_mode in rtl9300_force_sds_mode() is null and it
will be configured in switch-case. So print message after it.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amend commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-08 11:05:02 +02:00
INAGAKI Hiroshi
27a580df4a realtek: use MIPS fw_init_cmdline()
Use the generic function of MIPS in Linux Kernel instead of open coding
our own initialisation.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amend commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-08 11:05:02 +02:00
INAGAKI Hiroshi
5b37e3245d realtek: update SMP-related calls in prom_init()
The availabibity of probing CPC depends on CONFIG_MIPS_CPC symbol and it
will be checked in arch/mips/include/asm/mips-cpc.h. RTL9310 selects
this symbol, so the family check is redudant.

Furthermore, mips_cm_probe() is already called from setup_arch() in
mips/kernel/setup.c before prom_init(), and as such is not required.

Also move mips_cpc_probe() to run just before registering SMP ops.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[squash SMP change commits, reword commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
---
This patch only really has an impact on the rtl931x subtarget, which has
no devices. Noboby is currently set up to test these patches either, but
the end result is closer to MIPS_GENERIC, so I do not expect it to cause
issues.
2022-10-08 11:05:02 +02:00
INAGAKI Hiroshi
9b53a29a58 realtek: separate lock of RTL8231 from phy driver
RTL8231 and ethernet phys are not on the same bus, so separate the lock
to each own to cut off the unnecessary dependency.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-08 11:05:02 +02:00
Tom Herbers
7d6032f310 ath79: fix model name of Extreme Networks WS-AP3805i
Everywhere else the device is referred to as WS-AP3805i,
only the model name wrongly only said AP3805i.

Signed-off-by: Tom Herbers <mail@tomherbers.de>
2022-10-08 01:34:28 +02:00
Daniel Golle
f38276c9be mediatek: filogic: enable thermal, I2C and PWM of the BPi-R3
Setup thermal zone, select pins and enabled drivers for I2C (on 26-pin
GPIO bank) and PWM (1x fan and 1x GPIO bank).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-07 16:45:10 +01:00
Daniel Golle
5d921aa72f mediatek: filogic: add support for hw i2c, pwm and thermal
Add support for hardware I2C and PWM units found in the Filogic SoCs
as well as the CPU thermal support.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-07 16:45:10 +01:00
Daniel Golle
05501304ed kernel: refresh backport-5.15 patches
Refresh patches, removing unwanted git metadata from some backported
commits.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-07 16:45:10 +01:00
Robert Meijer
c3b9f00aaa
ath79: increase max tx ring buffer for ag71xx
This allows the user to specify a larger tx ring buffer size via ethtool.
Having symmetrical ring buffer sizes increases throughput on high bandwidth
(1 gbps tested) network connections.

The default value is not changed so the same behaviour is saved.

Signed-off-by: Robert Meijer <robert.s.meijer@gmail.com>
[ improve title, commit description and wrap to 80 columns ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-06 16:45:43 +02:00
Tomasz Maciej Nowak
ee38573093
ipq40xx: pakedge_wr-1: convert to DSA
Convert pakedge_wr-1 device to DSA and enable it.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>i
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-05 19:16:52 +02:00
Tomasz Maciej Nowak
70d9193b51
ipq40xx: luma_wrtq-329acn: convert to DSA
Convert luma_wrtq-329acn device to DSA and enable it.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-05 19:10:28 +02:00
Stijn Tintel
dc51342d34 qoriq: fix typo in FEATURES
There is no root-part FEATURE.

Reported-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-10-05 14:36:00 +03:00
Rafał Miłecki
a5265497a4 kernel: fix possible mtd NULL pointer dereference
Fixes: 1a9ee36734 ("kernel: backport mtd dynamic partition patch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-04 12:06:03 +02:00
Matthias Schiffer
149fc3a269
ramips: fix switch setup for ASUS RT-AX53U
The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface
corresponding to the non-existing port.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2022-10-03 13:23:41 +02:00
Petr Štetiar
606eb43b72 ipq40xx: glinet-b1300: fix LAN and WAN MAC address assigments
When testing the DSA changes with 5.15.60 kernel, I've noticed, that the
MAC addresses are not properly configured, there is single MAC being
used for LAN and WAN interfaces:

 eth0: 94:83:c4:XX:YY:4a (MAC on sticker)
 lan1@eth0: 94:83:c4:XX:YY:4a
 lan2@eth0: 94:83:c4:XX:YY:4a
 wan@eth0: 94:83:c4:XX:YY:4a
 wlan0: 94:83:c4:XX:YY:4a
 wlan1: 94:83:c4:XX:YY:4b

The same config, prior to the DSA conversion:

 lan/eth0: 94:83:c4:XX:YY:4a (MAC on sticker)
 wan/eth1: 94:83:c4:XX:YY:4b
 wlan0: 94:83:c4:XX:YY:4a
 wlan1: 94:83:c4:XX:YY:4b

Settings in ART partition:

 root@OpenWrt:/# hexdump -C /dev/mtd7 | grep '94 83'
 00000000  94 83 c4 XX YY 4a 94 83  c4 0e YY 4b ff ff ff ff  |.....J.....K....|
 00001000  20 2f 8d 8c 01 01 94 83  c4 XX YY 4a 00 00 20 00  | /.........J.. .|
 00005000  20 2f 5a 3a 01 01 94 83  c4 XX YY 4b 00 00 20 00  | /Z:.......K.. .|

So let's fix it by keeping same MAC address assigment as was done before
DSA conversion and while at it, define `label-mac-device` as well.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-03 08:06:43 +02:00
Tomas Lara
2b4f12e55b rockchip: switch to 5.15 kernel
Run tested: NanoPI R4S

Signed-off-by: Tomas Lara <tl849670@gmail.com>
2022-10-02 23:07:50 +02:00
Tomas Lara
fcaf7b32da kernel: add missing config symbols for 5.15
Add missing symbols, needed when rockchip kernel 5.15 is compile with ALL_KMODS=y

Signed-off-by: Tomas Lara <tl849670@gmail.com>
2022-10-02 23:07:50 +02:00
Tomas Lara
c4f0781eae rockchip: refresh kernel 5.15 config
Refreshed using make kernel oldconfig CONFIG TARGET=rockchip .

Signed-off-by: Tomas Lara <tl849670@gmail.com>
2022-10-02 23:07:50 +02:00
David Bauer
db19efee95 ipq40xx: disable boards not converted to DSA
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-10-02 23:04:39 +02:00
Robert Marko
116feb4a1c ipq40xx: remove non-converted network configs
Remove networking configs for non DSA converted boards in ipq40xx.
Currently, they are just causing clutter.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:39 +02:00
Robert Marko
132545785b ipq40xx: ipqess: enable threaded NAPI
Enable threaded NAPI by default in IPQESS driver as it significantly
improves network perfromance, in my testing about 100+ Mbps in WAN-LAN
routing.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:39 +02:00
Lech Perczak
b9b4c51b2b ipq40xx: Meraki MR33: convert MAC addresses to nvmem
This fixes assigning random MAC to br-lan interface upon boot.
While at that, rename at24@50 node to eeprom@50, to align with upstream
device tree style.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-10-02 23:04:39 +02:00
Robert Marko
550253bdf9 ipq40xx: convert some boards to DSA
Convert IPQ40xx boards to DSA setup.

Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Signed-off-by: ChunAm See <z1250747241@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:39 +02:00
Serhii Serhieiev
ad9ecd33cc ipq40xx: qca8k: introduce proper PSGMII calibration
Serhii and others have experienced PSGMII link degradation up to point
that it actually does not pass packets at all or packets arrive as zeros.
This usually happened after a couple of hot reboots.

Serhii has managed to track it down to PSGMII calibration not being done
properly and has fixed it, so all of the code is Serhii-s work.

Signed-off-by: Serhii Serhieiev <adron@mstnt.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:39 +02:00
Robert Marko
f5c62c6e91 ipq40xx: qca807x: drop kernel version checks
Since kernel 5.4 has been droppped from IPQ40xx, there is no need to keep
the version checks for kernels older than 5.10.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:39 +02:00
Serhii Serhieiev
12eebe8871 ipq40xx: qca807x: add suspend and resume ops
Currently, suspend and resume ops are not present, this means that if user
disables a DSA interface that the PHY-s remain alive and the link is up.

Fix it by using generic PHY suspend and resume ops.

Signed-off-by: Serhii Serhieiev <adron@mstnt.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:39 +02:00
Robert Marko
5293c08290 ipq40xx: sxtsq-5-ac: correct TCSR ESS type
SXTsq 5 ac uses RGMII on the port 5 and not PSGMII, so correct the TCSR
interface type property.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
a4470685ac ipq40xx: enable ethernet and DSA driver combo
Select the Ethernet driver, DSA tag driver and the DSA driver itself to
be built in the kernel config.
They automatically pull in switchdev and phylink.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
b1f21329d4 ipq40xx: add DSA switch driver
Qualcomm IPQ40xx SoC-s have a variant of QCA8337N switch built-in.

It shares most of the stuff with its external counterpart, however it is
modified for the SoC.
Namely, it doesn't have second CPU port (Port 6), so it has 6 ports
instead of 7.
It also has no built-in PHY-s but rather requires external PSGMII based
companion PHY-s (QCA8072 and QCA8075) for which it first needs to carry
out calibration before using them.
PSGMII has a SoC built-in PHY that is used to connect to the PHY-s which
unfortunately requires some magic values as the datasheet doesnt document
the bits that are being set or the register at all.

Since its built-in it is MMIO like other peripherals and doesn't have its
own MDIO bus but depends on the SoC provided one.

CPU connection is at Port 0 and it uses some kind of a internal connection
and no traditional RGMII/SGMII.
It also doesn't use in-band tagging like other qca8k switches so a shinfo
based tagger is used.

This is based on the current OpenWrt qca8k version that has been imported
from generic target.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
28b13bb157 ipq40xx: import qca8k from generic
This is just importing the qca8k driver from the generic target.
It will be used as the based for IPQ40xx version, this is just
to be able to see the diff.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
17a55f9c9d ipq40xx: add PSGMII PHY mode define
PSGMII is a Qualcomm specific mode similar to QSGMII but it has 5 SGMII
lines instead of 4 in QSGMII.

This just adds the support for the PHY layer to be able to identify the
mode for further use.
It is required for the DSA driver.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
a15ccc2fe0 ipq40xx: add IPQESS ethernet driver
IPQESS is the EDMA replacement driver for the IPQ40xx SoC built-in
ethernet controller.

Unlike EDMA it is Phylink based and doesnt touch PHY-s directly.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
45ad5beb80 ipq40xx: qca807x: always set PSGMII AZ WAR
There is no point in using a DT property to trigger setting the PSGMII
PHY AZ transmitting ability.
Especially since EEE can be disabled using ethtool anyway.

Fixup the mask for setting the workaround as only BIT(0) is actually being
changed and use the phy_clear_bits_mmd helper instead of reading, then
clearing the bit and writing back as it does everything for us.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
acc4add9a7 ipq40xx: add shinfo based DSA tag driver
IPQ40xx requires a special DSA tag driver despite using the QCA8337N
switch.
However they have changed the header format and the existing QCA tag
driver cannot be reused.

For details on how it actually works and else read the patch commit
description.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
ccd08ef912 ipq40xx: disable nodes instead of deleting them
There is no reason to delete the DT PHY nodes
as you can just disable them.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
378d1a6569 ipq40xx: qca807x: add SFP improvements
Currently, QCA807x doesnt do any kind of validation to see whether it
actually supports the inserted module.

So lets add checks to allow only 1000BaseX and 100BaseFX based modules.

While adding validation, move fiber configuration to insert/remove events
instead of always doing it at config time.
This allows getting rid of the DT property for fiber enable and now only
the upstream sfp phandle is required.

Since we are refactoring fiber related code, lets heavily simplify the
status polling as the current logic is overcomplicated due to previous
wish to support non standard SFP cages that dont have pins properly
connected, that is removed now and only proper SFP cages will work.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
27b441cbaf ipq40xx: drop ESSEDMA + AR40xx DTS nodes
In order to start working on IPQESS + DSA drop
the old ESSEDMA + AR40xx DTS nodes.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Robert Marko
6d24d10f3d ipq40xx: drop ESSEDMA + AR40xx
In order to start working on IPQESS + DSA drop the old ESSEDMA + AR40xx
driver combo.

Remove the kernel symbols, disable swconfig and drop swconfig package
as they are not needed anymore.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-02 23:04:38 +02:00
Aleksander Jan Bajkowski
fbd33d6164 lantiq: enable interrupts on second VPEs
This patch is needed to handle interrupts by the second VPE on the Lantiq
ARX100, xRX200, xRX300 and xRX330 SoCs. Switching some ICU interrupts to
the second VPE results in a hang. Currently, the vsmp_init_secondary()
function is responsible for enabling these interrupts. It only enables
Malta-specific interrupts (SW0, SW1, HW4 and HW5).

The MIPS core has 8 interrupts defined. On Lantiq SoCs, hardware
interrupts are wired to an ICU instance. Each VPE has an independent
instance of the ICU. The mapping of the ICU interrupts is shown below:
SW0(IP0) - IPI call,
SW1(IP1) - IPI resched,
HW0(IP2) - ICU 0-31,
HW1(IP3) - ICU 32-63,
HW2(IP4) - ICU 64-95,
HW3(IP5) - ICU 96-127,
HW4(IP6) - ICU 128-159,
HW5(IP7) - timer.

This patch enables all interrupt lines on the second VPE.

This problem affects multithreaded SoCs with a custom interrupt controller.
SOCs with 1004Kc core and newer use the MIPS GIC. At this point, I am aware
that the Realtek RTL839x and RTL930x SoCs may need a similar fix. In the
future, this may be replaced with some generic solution.

Tested on Lantiq xRX200.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-02 20:22:54 +02:00
Alexey Kosmakov
a664d39c5b ramips: add support for SNR SNR-CPE-ME2-Lite
SNR SNR-CPE-ME2-Lite is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A.

Specification:
    - SoC           : MediaTek MT7621A
    - RAM           : DDR3 128 MiB
    - Flash         : SPI-NOR 16 MiB
    - WLAN          : 2.4 GHz 2T2R (MediaTek MT7603E)
                      5 GHz 2T2R (MediaTek MT7613BE)
    - Ethernet      : 10/100/1000 Mbps x5
      - Switch      : MediaTek MT7530 (SoC)
    - UART          : through-hole on PCB
      - J4: 3.3V, GND, TX, RX
      - 57600n8
    - Power         : 12 VDC, 1.5 A

Flash instruction via WEB (firmware 1.10.4 and later)
    1. Boot SNR-CPE-ME2-Lite normally with "Router" mode
    2. Access to "http://192.168.1.1/" and open "Administration -> Management" page
    3. Select the OpenWrt factory image in "Firmware update" section and click "Update" button
    4. Wait ~120 seconds to complete flashing

Flash instruction via TFTP (all version):
    1. Boot SNR-CPE-ME2-Lite to recovery mode (hold the reset button while power on)
    2. Send firmware via TFTP client:
       TFTP Server address: 192.168.1.1
       TFTP Client address: 192.168.1.131
    3. Wait ~120 seconds to complete flashing

Signed-off-by: Alexey Kosmakov <a.kosmakov@nagtech.ru>
2022-10-02 20:21:55 +02:00
Mark King
bf5b1a53d4 ramips: enable LZMA loader to fix Linksys RE6500 boot
At some point after 21.02.3 and before 22.03.0, the size limits of the
Linksys RE6500 were reached and prevent booting from the 22.03.0 release
or builds of current SNAPSHOT. This patch allows builds of master to boot
again and has been tested on my device.

Fixes: #8577

Signed-off-by: Mark King <mark@vemek.co>
2022-10-02 20:21:55 +02:00
John Audia
eed0a31b90 kernel: bump 5.10 to 5.10.146
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-02 20:21:55 +02:00
John Audia
8fe67fae1d kernel: bump 5.10 to 5.10.145
Manually rebased:
  hack-5.10/780-usb-net-MeigLink_modem_support.patch

Removed upstreamed:
  patches-5.10/110-gpio-mpc8xxx-Fix-support-for-IRQ_TYPE_LEVEL_LOW-flow.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.145&id=24196210b198e8e39296e277bb93b362aa207775

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-02 20:21:55 +02:00
John Audia
e71a360f57 kernel: bump 5.15 to 5.15.71
Removed upstreamed:
  uml/patches-5.15/001-um-fix-default-console-kernel-parameter.patch[1]

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.71&id=e1dbe8a62098b20f5093cf75ade2f2dc9259b006

Signed-off-by: John Audia <therealgraysky@proton.me>
Compile-tested: mvebu/cortexa72 (RB5009UG+S+IN)
Run-tested: mvebu/cortexa72 (RB5009UG+S+IN)
2022-10-02 20:21:55 +02:00
John Audia
e1b009c1fe kernel: bump 5.15 to 5.15.70
Manually rebased:
  hack-5.15/780-usb-net-MeigLink_modem_support.patch

Removed upstreamed:
  patches-5.15/110-gpio-mpc8xxx-Fix-support-for-IRQ_TYPE_LEVEL_LOW-flow.patch[1]

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.70&id=89cfddd416bac41ff35f37f928ed3d7fefef908e

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-02 20:21:55 +02:00
Santiago Piccinini
2ad949b11d ath79: fix LibreRouter-v1 watchdog and poe_pass
Watchdog and poe_passthrough gpios require the jtag disabled.

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
2022-10-02 11:39:13 +02:00
Sander Vanheule
918e774658 realtek: use correct CAUSEF_DC macro in prom.c
The workaround for an already-enabled R4K timer used a non-existent
macro CAUSE_DC. Fix compiling by using the actual macro CAUSEF_DC.

Fixes: b7aab19585 ("realtek: SMP handling of R4K timer interrupts")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-01 09:56:54 +02:00
Markus Stockhausen
b7aab19585 realtek: SMP handling of R4K timer interrupts
Until now there has been no good explanation why we mess with the R4K
timer on SMP. After extensive testing and looking at the SDK code it
becomes clear what it is all about.

When we disable the CEVT_R4K module (we will do with the new timer
driver) the R4K timer hardware still fires interrupts on the secondary
CPU. To get around this we have two options:

- Disable IRQ 7
- Stop the counter completely

This patch selects option two because this is the root of evil.. To be
on the safe side we will do it only in case the CEVT_R4K module is
disabled.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
2022-10-01 09:22:32 +02:00
Markus Stockhausen
2b12da1313 realtek: fix SMP startup
The scope of the SMP startup structure is wrong. It is created on the
stack and not as a global variable. This can lead to startup failures.

Fixes: 3f41360eb7 ("realtek: use upstream recommendation for CPU start")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de
2022-10-01 09:22:32 +02:00
Olliver Schinagl
f1f97db627
realtek: Convert incorrect v5.10 patches
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.

However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.

This commit tries to rectify that, by digging in the history to find
where and how it was first added.

It is by no means perfect and also shows some patches that should have
been long gone.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-10-01 02:47:57 +02:00
Olliver Schinagl
ba6096d04b
ath79: Convert incorrect 5.10 and 5.15 patches
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.

However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.

This commit tries to rectify that, by digging in the history to find
where and how it was first added.

It is by no means perfect and also shows some patches that should have
been long gone.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-10-01 02:47:56 +02:00
Olliver Schinagl
d5bf46bbe8
generic: Convert incorrect generic/5.10 patches
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.

However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.

This commit tries to rectify that, by digging in the history to find
where and how it was first added.

It is by no means perfect and also shows some patches that should have
been long gone.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-10-01 02:47:56 +02:00
Daniel Golle
ca0e7054d8 ramips: add led driver to UniFi FlexHD defaut package set
Add kmod-leds-ubnt-ledbar to the packages selected by default on the
UniFi FlexHD access point.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-30 13:29:58 +01:00
Daniel Golle
0419f7dead mediatek: add support t-phy settings from efuse on MT7986
Import patches from mtk-openwrt-feeds (MTK SDK) to support reading
t-phy settings affecting PCIe as well as USB2 and USB3 from efuse.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-30 13:29:58 +01:00
Daniel Golle
b18b5a7ca3 mediatek: filogic: add efuse layout to mt7986a.dtsi
efuse is used to store board-specific settings of some of the in-SoC
peripherals. Add it to device tree, so it gets probed on boot and can
be accessed by other drivers.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-30 13:29:58 +01:00
Daniel Golle
243a2184f2 mediatek: add patch allowing 1-byte wide access to efuse
Allow byte-wise access to mtk-efuse as some drivers require that.
Patch imported from mtk-openwrt-feeds (MTK SDK).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-30 13:29:58 +01:00
Felix Fietkau
c7c7905bce kernel: fold lzma debloat patch into the patch adding the code
Reduces the number of hack patches

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-09-30 13:13:51 +02:00
Felix Fietkau
36f2ab4bfd kernel: move kernel image cmdline hack to the octeon target
It is the only remaining user of this hack

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-09-30 13:13:51 +02:00
Felix Fietkau
2e375e9b31 kernel: remove hack patch, move kirkwood specific kmods to target modules.mk
Tweaking the KCONFIG line of kmod-ata-marvell-sata makes the hack patch
unnecessary

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-09-30 12:59:19 +02:00
Felix Fietkau
4363faef8a kernel: move ubnt ledbar driver to a separate package
Simplifies the tree by removing a non-upstream kernel patch and related kconfig
symbols

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-09-30 11:28:51 +02:00
Felix Fietkau
a0a4cfd83b kernel: remove udp tunnel kconfig selection hack
The corresponding kmod package is marked as HIDDEN and selected by all
other kernel modules that need it, so the kconfig side will be in sync
without manual selection

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-09-30 11:28:51 +02:00
Rafał Miłecki
77d9cce604 bcm53xx: backport clk driver fix for DT nodes names
It allows dropping downstream patch renaming DT nodes.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-09-29 05:51:25 +02:00
Chris Osgood
c5e167e0d6
build: fix warnings from grep
Fixes build warnings when using newer versions of grep.

Signed-off-by: Chris Osgood <chris_github@functionalfuture.com>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
2022-09-28 17:17:48 +02:00
Kazuhiro Ito
e739ccb2f6 ramips: update MAC address configuration for Buffalo WSR-1166DHP
Convert MAC address and label_mac configuration of Buffalo
WSR-1166DHP to use the generic function of OpenWrt.

Apply commit 770cfe9 for WCR-1166DS to WSR-1166DHP too.

Tested on the device and MAC address is kept before and after this
change.

Signed-off-by: Kazuhiro Ito <kzhr@d1.dion.ne.jp>
2022-09-28 22:35:02 +09:00
Daniel Golle
9e08724634 kernel: mtk_ppe: use MTK_FOE_STATE_INVALID instead of *_UNBIND
Instead of dropping *fix-typo-in-__mtk_foe_entry.patch which effectively
means keeping the (also wrong) assignment of MTK_FOE_STATE_BIND, rather
use MTK_FOE_STATE_INVALID as that works well on both older (NETSYS_V1)
and newer (NETSYS_V2) MediaTek SoCs.

Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-28 03:34:47 +01:00
Christian Marangi
165b66d910
realtek: rtl931x: fix missing CONFIG_COMMON_CLK_REALTEK config flag
When the realtek clock driver was introduced, CONFIG_COMMON_CLK_REALTEK
was not correctly disabled for other subtarget. Add the missing config
flag to fix compilation error on buildbot.

Fixes: 4850bd887c ("realtek: add RTL83XX clock driver")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-09-28 01:15:47 +02:00
Daniel Golle
e8b00cfdcb kernel: rename upstreamed patches and import fixes
Move and rename patches which were merged upstream and import follow-up
fixes for MediaTek Ethernet offloading features on MT7622 and Filogic
platforms. Remove patch
793-net-ethernet-mtk_eth_soc-fix-typo-in-__mtk_foe_entry.patch
which breaks hardware flow offloading on MT7622, it will be reverted
upstream as well.

Fixes: c93c5365c0 ("kernel: pick patches for MediaTek Ethernet from linux-next")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-27 17:07:20 +01:00
Felix Fietkau
3a8825ad6a build: fix issues with targets installed via feeds
- fix including modules.mk when a target is being replaced
- fix calling make targets from target/linux

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-09-27 13:41:12 +02:00
Jan Hoffmann
d924a75be3 realtek: fix RTL839x egress tag for ports >= 32
Don't overwrite AS_DPM and L2LEARNING flags when dest_port is >= 32.

Fixes: 1773264a0c ("realtek: correct egress frame port verification")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-09-25 20:53:24 +02:00
Nick Hainke
a67f484e67 octeon: fix imagebuilder generation by introducing generic target
The generic imagebuilder does not have a generic in the name, although
this is the default naming scheme. Use bcm53xx as template for this fix.

Before the fix:
  openwrt-imagebuilder-octeon.Linux-x86_64.tar.xz

After:
  openwrt-imagebuilder-octeon-generic.Linux-x86_64.tar.xz

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-09-24 23:53:53 +02:00
Florian Eckert
99b6e3cb41 x86/config-5.10: geode: add missing CONFIG_WATCHDOG_CORE option
If this module is not set to y, then I get the following compilation
error during geode build.

Package kmod-w83627hf-wdt is missing dependencies for the following libraries:
watchdog.ko

Setting the linux CONFIG_WATCHDOG_CORE to y as in all other targets
fixes this issue.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-09-24 23:53:53 +02:00
Florian Eckert
fea1705819 x86/config-5.15: geode: add missing CONFIG_WATCHDOG_CORE option
If this module is not set to y, then I get the following compilation
error during geode build.

Package kmod-w83627hf-wdt is missing dependencies for the following
libraries:
watchdog.ko

Setting the linux CONFIG_WATCHDOG_CORE to y as in all other targets
fixes this issue.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-09-24 23:53:53 +02:00
Florian Eckert
355c02d963 linux/x86: add missing CONFIG_WATCHDOG_CORE to *-wdt
The packages also need a dependency to watchdog core. This commit adds the
needed WATCHDOG_CORE dependency.

https://github.com/torvalds/linux/blob/master/drivers/watchdog/Kconfig

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-09-24 23:53:53 +02:00
Giammarco Marzano
0de6a3339f ipq40xx: Add ZTE MF289F
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).

Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.

There are currently two hardware revisions, which
differ on the 5Ghz radio:

AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz

Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
	(QCA9984): a/n/ac, 4x4 HW REV AT1
	(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot

Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
   in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
   GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
   (refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:

setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr

5. Please make backup of original partitions, if you think about revert to
   stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:

WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin

ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin

6. Login via ssh or serial and remove stock partitions
   (default IP 192.168.0.1):

 # this can return an error, if ubi was attached before
 # or rootfs part was erased before.
ubiattach -m 17

 # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
 # some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data

7. download and install image via sysupgrade -n
 (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
 to the device's /tmp directory)

 sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin

Sometimes it could print ubi attach error, but please ignore it
if process goes forward.

Flash Layout

NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"

SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"

Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
   for the device on a TFTP in the server's root.
   This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
   connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:

This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000

This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize

This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize

After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router

Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
INAGAKI Hiroshi
c34f071972 ipq40xx: add support for Sony NCP-HG100/Cellular
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.

Specification:

- SoC                   : Qualcomm IPQ4019
- RAM                   : DDR3 512 MiB (H5TC4G63EFR)
- Flash                 : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN                  : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet              : 10/100/1000 Mbps x2
  - Transceiver         : Qualcomm QCA8072
- WWAN                  : Telit LN940A9
- Z-Wave                : Silicon Labs ZM5101
- Bluetooth             : Qualcomm CSR8811
- Audio DAC             : Realtek ALC5629
- Audio Amp.            : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
  - RGB LED, Fan, Temp. sensors
- Touch Sensor          : Cypress CY8C4014LQI
- RGB LED driver        : TI LP55231 (2x)
- LEDs/Keys             : 11x, 6x
- UART                  : through-hole on PCB
  - J1: 3.3V, TX, RX, GND from tri-angle marking
  - 115200n8
- Power                 : 12 VDC, 2.5 A

Flash instruction using initramfs image:

1. Prepare TFTP server with the IP address 192.168.132.100 and place the
   initramfs image to TFTP directory with the name "C0A88401.img"

2. Boot NCP-HG100/Cellular and interrupt after the message
   "Hit any key to stop autoboot:  2"

3. Perform the following commands and set bootcmd to allow booting from
   eMMC

   setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
   saveenv

4. Perform the following command to load/boot the OpenWrt initramfs image

   tftpboot && bootm

5. On the initramfs image, perform sysupgrade with the sysupgrade image
   (if needed, backup eMMC partitions by dd command and download to
   other place before performing sysupgrade)

6. Wait for ~120 seconds to complete flashing

Known issues:

- There are no drivers for audio-related chips/functions in Linux Kernel
  and OpenWrt, they cannot be used.

- There is no driver for MINI54FDE Micro-Controller Unit, customized for
  this device by the firmware in the MCU. This chip controls the
  following functions, but they cannot be controlled in OpenWrt.

  - RGB LED
  - Fan
    this fan is controlled automatically by MCU by default, without
    driver
  - Thermal Sensors (2x)

- Currently, there is no driver or tool for CY8C4014LQI and cannot be
  controlled. It cannot be exited from "booting mode" and moved to "normal
  op mode" after booting. And also, the 4x buttons (mic mute, vol down,
  vol up, alexa trigger) connected to the IC cannot be controlled.

  - it can be exited from "booting mode" by installing and executing
    i2cset command:

    opkg update
    opkg install i2c-tools
    i2cset -y 1 0x14 0xf 1

- There is a connection issue on the control by uqmi for the WWAN module.
  But modemmanager can be used without any issues and the use of it is
  recommended.

- With the F2FS format, too many errors are reported on erasing eMMC
  partition "rootfs_data" while booting:

  [    1.360270] sdhci: Secure Digital Host Controller Interface driver
  [    1.363636] sdhci: Copyright(c) Pierre Ossman
  [    1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
  [    1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
  ...
  [    1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
  [    1.528325] mmc0: new HS200 MMC card at address 0001
  [    1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
  [    1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
  [    1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
  [    1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
  [    1.550323] Alternate GPT is invalid, using primary GPT.
  [    1.561669]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
  ...
  [    8.841400] mount_root: loading kmods from internal overlay
  [    8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
  [    8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
  [    9.240465] block: attempting to load /etc/config/fstab
  [    9.246722] block: unable to load configuration (fstab: Entry not found)
  [    9.246863] block: no usable configuration
  [    9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
  [    9.438915] urandom_read: 5 callbacks suppressed
  [    9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
  [   12.243332] mmc_erase: erase error -110, status 0x800
  [   12.246638] mmc0: cache flush error -110
  [   15.134585] mmc_erase: erase error -110, status 0x800
  [   15.135891] mmc_erase: group start error -110, status 0x0
  [   15.139850] mmc_erase: group start error -110, status 0x0
  ...(too many the same errors)...
  [   17.350811] mmc_erase: group start error -110, status 0x0
  [   17.356197] mmc_erase: group start error -110, status 0x0
  [   17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
  [   17.446910] mmc0: tuning execution failed: -5
  [   17.447111] mmc0: cache flush error -110
  [   18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
  [   18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
  [   18.198691] block: attempting to load /etc/config/fstab
  [   18.198972] block: unable to load configuration (fstab: Entry not found)
  [   18.203029] block: no usable configuration
  [   18.211371] mount_root: overlay filesystem has not been fully initialized yet
  [   18.214487] mount_root: switching to f2fs overlay

  So, this support uses ext4 format instead which has no errors.

Note:

- The primary uart is shared for debug console and Z-Wave chip. The
  function is switched by GPIO15 (Linux: 427).

  value:

    1: debug console
    0: Z-Wave

- NCP-HG100/Cellular has 2x os-image pairs in eMMC.

  - 0:HLOS, rootfs
  - 0:HLOS_1, rootfs_1

  In OpenWrt, the first image pair is used.

- "bootipq" command in U-Boot requires authentication with signed-image
  by default. To boot unsigned image of OpenWrt, use "mmc read" and
  "bootm" command instead.

- This support is for "Cellular" variant of NCP-HG100 and not tested on
  "WLAN" (non-cellular) variant.

- The board files of ipq-wifi may also be used in "WLAN" variant of
  NCP-HG100, but unconfirmed and add files as for "Cellular" variant.

- "NET" LED is used to indicate WWAN status in stock firmware.

- There is no MAC address information in the label on the case, use the
  address included in UUID in the label as "label-MAC" instead.

- The "CLOUD" LEDs are partially used for indication of system status in
  stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
  connected to the MCU.

MAC addresses:

LAN    : 5C:FF:35:**:**:ED (ART, 0x6    (hex))
WAN    : 5C:FF:35:**:**:EF (ART, 0x0    (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz  : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))

partition layout in eMMC (by fdisk, GPT):

Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910

Number  Start (sector)    End (sector)  Size Name
     1              34            1057  512K 0:SBL1
     2            1058            2081  512K 0:BOOTCONFIG
     3            2082            3105  512K 0:QSEE
     4            3106            4129  512K 0:QSEE_1
     5            4130            4641  256K 0:CDT
     6            4642            5153  256K 0:CDT_1
     7            5154            6177  512K 0:BOOTCONFIG1
     8            6178            6689  256K 0:APPSBLENV
     9            6690            8737 1024K 0:APPSBL
    10            8738           10785 1024K 0:APPSBL_1
    11           10786           11297  256K 0:ART
    12           11298           11809  256K 0:HSEE
    13           11810           28193 8192K 0:HLOS
    14           28194           44577 8192K 0:HLOS_1
    15           44578          306721  128M rootfs
    16          306722          568865  128M rootfs_1
    17          568866         3958065 1654M rootfs_data

[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
Tomasz Maciej Nowak
0410c95f0b ipq40xx: base-files: properly close case
Fix this occurrence during boot:
/bin/board_detect: line 10: Unsupported: not found

Fixes: 80baffd2aa (" ipq40xx: add support for Pakedge WR-1")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-24 23:53:53 +02:00
Tomasz Maciej Nowak
04eb080290 ipq40xx: luma_wrtq-329acn: differentiate ethernet mac addresses
On OEM firmware both addresses for In and Out ports are different. Set
them as such also in OpenWrt.

Fixes: e24635710c (" ipq40xx: add support for Luma Home WRTQ-329ACN")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-24 23:53:53 +02:00
Christian Lamparter
3aec35ab96 apm821xx: make 5.15 kernel default
5.15 has been available for some time for testing.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
Christian Lamparter
48ef669759 apm821xx: refresh 5.15 config
use the toolchain's default CPU (464fp) as the CPU option.
This fixes a CPU selection prompt which shows up now.

CPU selection
> 1. Generic 32 bits powerpc (POWERPC_CPU) (NEW)
  2. Rely on the toolchain's implicit default CPU (TOOLCHAIN_DEFAULT_CPU) (NEW)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
Kasparas Elzbutas
e562746263 ipq40xx: fix RUTX10 Wi-Fi woes
This partially reverts:
commit cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")

U-Boot on these devices mangles the device tree,
so nvmem-cell type calibration doesn't work.

Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Signed-off-by: Kasparas Elzbutas <elzkas@gmail.com>
(added reference to commit, rewrote commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
Christian Lamparter
e2f0821b5a uml: add Kernel 5.15 support via testing
Add the latest default Kernel for testing.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
Christian Lamparter
8bea5edf89 uml: fix 5.10 build
the 5.10 uml build currently breaks with:

/usr/bin/ld: arch/um/os-Linux/signal.o: in function `sigusr1_handler':
arch/um/os-Linux/signal.c:141: undefined reference to `uml_pm_wake'

But there's an upstream fix for this. Backport the fix
for now but also let upstream know so it finds its way
through the -stable releases.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
Hauke Mehrtens
f08f7e88c9 kernel: Move some IOMMU options to generic
This adds some missing IOMMU related options for x86/64 and moves some
of them to generic for all targets.

On x86 IOMMU_DEFAULT_DMA_LAZY is used by default, on all other platforms
IOMMU_DEFAULT_DMA_STRICT is the default. we just follow the default
kernel configuration here.

Fixes: 8fea4a102c ("x86/64: enable IOMMU support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-09-24 13:49:47 +02:00
Nick Hainke
579703f38c ath79: switch to 5.15 as default kernel
The 5.15 kernel has new interesting features like MGLRU. Most of the
targets already have added support for testing kernel 5.15 since April
2022. Set 5.15 as default for all subtargets.

Testing support was added here:
- ae6bfb7d67 ("ath79: tiny: add 5.15 support for tiny subtarget")
- 9a0155bc4f ("ath79: add 5.15 support for generic subtarget")
- 5af9aafabb ("ath79: mikrotik: add 5.15 support for mikrotik subtarget")
- f3fa68e515 ("ath79: nand: add 5.15 support for nand subtarget")

Tested on:
- Nanostation M5 XM (tiny)
- TP-Link EAP-225 Outdoor (generic)
- TP-Link CPE210 (generic)

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-09-24 13:04:24 +02:00
Will Moss
a24e07700d
kernel: fix mac-address-increment on driver probe defer
Fixes situations where MAC address gets incremented multiple times
if device initialization fails at first and then is deferred.

Fixes: d284e6ef0f ("treewide: convert mtd-mac-address-increment* to generic implementation")
Signed-off-by: Will Moss <willormos@gmail.com>
2022-09-23 12:16:29 +02:00
Christian Marangi
dce035bb71
generic: 5.15: add missing PAGE_POOL_STATS config
Add new PAGE_POOL_STATS config backported for the mtk offload patches.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-09-23 02:06:00 +02:00
Daniel Golle
c93c5365c0
kernel: pick patches for MediaTek Ethernet from linux-next
Pick patches with several fixes and improvements, preparation for
upcoming WED (TX) [1] as well as basic XDP support [2] with MediaTek's
Filogic SoCs to the mtk_eth_soc driver.

Also pick follow-up patch fixing Ethernet on MT7621 [3].

Tested on Bananapi BPi-R3 (MT7986), Bananapi BPi-R64 (MT7622),
Bananapi BPi-R2 (MT7623), MikroTik RouterBoard M11G (MT7621).

[1]: https://patchwork.kernel.org/project/netdevbpf/list/?series=662108&state=*
[2]: https://patchwork.kernel.org/project/netdevbpf/list/?series=675368&state=*
     (the first part of the series adding wed nodes to mt7986a.dtsi was
      applied to the copy of mt7986a.dtsi in our tree)
[3]: https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=5e69163d3b9931098922b3fc2f8e786af8c1f37e

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-22 23:55:02 +01:00
Felix Fietkau
6eeb5d4564 kernel: disable wireless extensions only when needed
They are only needed by a few very old drivers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-09-22 15:26:58 +02:00
John Audia
37a0cae33e kernel: bump 5.15 to 5.15.69
All patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-22 12:46:55 +02:00
John Audia
eff4f8b2f0 kernel: bump 5.10 to 5.10.144
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-22 12:46:55 +02:00
Hauke Mehrtens
8762759015 kernel: Reorder kernel configuration
This was done by running this:
./scripts/kconfig.pl '+' target/linux/generic/config-5.15 /dev/null > target/linux/generic/config-5.15-new
mv target/linux/generic/config-5.15-new target/linux/generic/config-5.15

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-09-22 11:48:39 +02:00
Hauke Mehrtens
fa578335c9 kernel: Deactivate CONFIG_DEFAULT_FQ_PIE by default
When building OpenWrt with CONFIG_ALL_KMODS the kernel build will ask
for CONFIG_DEFAULT_FQ_PIE option. This deactivates it by default.

Fixes: c3e4a0d99b ("kernel: netsupport: Add FQ-PIE as an optional sched kmod and extract PIE")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-09-22 11:46:48 +02:00
Nicola Corna
8fea4a102c x86/64: enable IOMMU support
Enable IOMMU support for Intel and AMD x86 platforms. With this, when the
vfio module is present, physical PCI devices can be passed to VMs, for
example with `qemu-system-x86_64 -device vfio-pci,host=05:00.0 ...`.

IOMMU support increases the kernel size by a small amount (~370KB, from
5239840 B to 5611200 B, a ~7% increase in size).

Signed-off-by: Nicola Corna <nicola@corna.info>
2022-09-21 13:06:10 +02:00
Rafał Miłecki
1722e23ffc bcm4908: fix -EPROBE_DEFER support in bcm4908_enet
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-09-21 07:54:21 +02:00
Rafał Miłecki
5652f378c6 kernel: update U-Boot NVMEM driver
1. Fix casting
2. Support DT-defined variables

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-09-20 23:08:19 +02:00
Rafał Miłecki
137149847d bcm4908: backport mtd parser for Broadcom's U-Boot partition
Broadcom's U-Boot contains environment data blocks. They need to be
found (offsets aren't predefined) to access env variables.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-09-20 22:36:46 +02:00
Stijn Tintel
117f41ee95 mediatek: fix Unifi 6LR network config
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.

Fix this by using a wildcard that matches all the variants.

Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a7 ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a11 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
2022-09-20 22:07:59 +03:00
Felix Fietkau
0a72695844 kernel: backport MTK ethernet/WLAN offload fixes
Fixes issues with offloading to WED, especially with VLAN bridges involved

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-09-20 12:08:26 +02:00
Florian Eckert
027845b4ce target/x86: add grub2-bios-setup to DEFAULT_PACKAGES
With the commit 5876d6a62f the command under
`/usr/sbin/grub-bios-setup` has been moved to its own package named
`grub-bios-setup`.

The script `81_upgrade_bootloader` under `/lib/preinit` is used by all
x86 targets to update the bootloader. The script is using the command
`grub-bios-setup` for this.

I get the following output at the first boot after the upgrade.
`/etc/preinit: line 9: /usr/sbin/grub-bios-setup: not found`.

To fix this, the DEFAULT_PACKAGES dependency is extended by the entry
`grub2-bios-setup` so that the missing command is installed again.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-09-19 19:30:15 +02:00
Andrew Sim
e2ffb61821
ipq40xx: fix power LED colour ID in Netgear WAC510 dts
led_power_green color ID in dts is mistakenly set to amber so
correct it by setting it to green

Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
2022-09-19 17:49:56 +02:00
Christian Marangi
691b3dd35e
generic: 5.15: backport stmmac patches to change MTU
Backport stmmac patches to change MTU while the interface is up.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-09-19 15:19:54 +02:00
Christian Marangi
7ace30aeb6
generic: 5.15: qca8k: backport code split patch
Backport upstream code split patch for qca8k needed for ipq40xx target
to correctly implement a DSA driver.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-09-19 15:19:53 +02:00
Christian Marangi
ddcebda08b
generic: 5.15: qca8k: add kernel version tag on backport patch
Add kernel tag that introduced the patch on backport patch.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-09-19 15:19:53 +02:00
Markus Stockhausen
3f41360eb7 realtek: use upstream recommendation for secondary CPU start
Currently we fix interrupts/timers for the secondary CPU by patching
vsmp_init_secondary(). Get a little bit more generic and use the
upstream recommended way instead. Additionally avoid a check around
register_cps_smp_ops() because it does that itself.

See https://lkml.org/lkml/2022/9/12/522

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
2022-09-18 20:38:56 +02:00
Markus Stockhausen
bcb5d6b21b realtek: avoid wrong interrupt routing
The interrupt controller depends on two control registers. GIMR enables
or disables interrupts and IRRx routes these to MIPS CPU interrupts 2-7.
Wiki currently states "A value of '0' (in IRRx) disconnects this input from
the output line, independent of the line's setting in GIMR."

Contrary to normal intuition this statement DOES NOT mean, that interrupts
can be disabled by IRRx alone. The sad truth was discovered by enabling
SMP for an Zyxel XGS1010 on the 930x target. It shows that driver and
interrupts behave as follows:

- Timer 0 interrupt 7 has active routing to CPU0 and no routing to CPU1
- Timer 1 interrupt 8 has no routing to CPU0 and active routing to CPU1
- Unmasking (enabling) interrupts writes 1 bits to all GIMR registers
- Masking (disabling) interrupts writes 0 bits to both GIMR registers

During operation we can encounter a situation like

- GIMR bit for a interrupt/CPU combination is set to enabed (=1)
- IRRx routing bits for a interrupt/CPU combination are set to disabed (=0)

This setting already allows the hardware to fire interrupts to the target
CPU/VPE if the other CPU/VPE is currently busy. Especially for CPU bound
timer interrupts this is lethal. If timer interrupt 7 arrives at CPU1 and
vice versa for interrupt 8 the restart trigger gets lost. The timer dies
and a msleep() operation in the kernel will halt endlessly.

Fix this by tracking the IRRx active routing setting in a new bitfield with
0="routing active" and 1="no routing". Enable interrupts in GIMR only
for a interrupt & CPU if routing is active. Thus we have

- GIMR = 0 / IRRx = 0 -> everything disabled
- GIMR = 1 / IRRx > 0 -> active and normal routing
- GIMR = 0 / IRRx > 0 -> masked (disabled) with normal routing
- GIMR = 1 / IRRx = 0 -> no longer possible

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
2022-09-18 20:38:56 +02:00
Sungbo Eo
f0ea3df439 ipq40xx: disable devices with 3MiB kernel size
The image builds for Linksys EA6350 v3, EA8300, and MR8300 currently
fail on buildbots due to the KERNEL_SIZE, as stated in commit
17b7756b5a ("ipq40xx: 5.15: add testing kernel version"). Disable
these boards for now.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-09-18 21:33:50 +09:00
Arınç ÜNAL
c77858aa79 ramips: mt7621-dts: change phy-mode of gmac1 to rgmii
Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-09-18 11:50:32 +02:00
Arınç ÜNAL
2a6ef7f53d ramips: fix GB-PC1 and GB-PC2 LEDs
Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.

Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired
to GPIO 3 or 4 and the wiring is currently unknown.

Set ethyellow-orange to display link state and activity of the ethyellow
interface for GB-PC2.

Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-09-18 11:50:32 +02:00
Sander Vanheule
fe5a2f334f realtek: use Device prefix for common recipes
The Build prefix is used for image build commands, while the Device
prefix should be used for base recipes for devices. Apply the same
naming convention here.

While touching the file, also fix the mixed indentation.

Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-18 10:12:19 +02:00
Olliver Schinagl
d2fa68379f realtek: move Netgear recipe to subtarget Makefile
There seems to be no reason to have the Netgear switches as part of
the main Makefile. Move it to its subtarget-specific Makefile since
it is only applicable there.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[update commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-17 22:27:32 +02:00
Sander Vanheule
51ecfb086c realtek: move hpe_1920 recipe to common.mk
Currently supported HPE 1920 devices all have an RTL838x SoC, but there
are larger switches with RTL839x SoCs, although currently not supported.
Move the build recipe to common.mk so the larger devices can also make
use of the recipe, while moving it out of the main Makefile.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-17 22:20:32 +02:00
Sander Vanheule
9338c09ecb realtek: merge duplicated DGS-1210 recipes
The D-Link DGS-1210 device series currently has supported devices with
both RTL838x and RTL839x SoCs. An image build recipe has been defined in
both subtarget makefiles, but these are mostly identical, save for the
SOC variable.

Move the SOC variable from the DGS-1210 build recipes to the applicable
devices, and put the remaining duplicate code in a shared Makefile.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-17 22:12:35 +02:00
Markus Stockhausen
e04e821471 realtek: add support for DGS-1210-52
Hardware specification
----------------------

* RTL8393M SoC, 1 MIPS 34Kc core @ 700MHz
* 128MB DRAM
* 32MB NOR Flash
* 48 x 10/100/1000BASE-T ports
  - 6 x External PHY with 8 ports (RTL8218D)
* 4 x Gigabit RJ45/SFP Combo ports
  - External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J14

The gpio-restart node is not required but it does reset the switch.

TODO: The 4 combo ports attached to the RTL8214FC are not detect
properly. Linux kernel reports 49 and 50 as "External RTL8393 SERDES"
and 51 and 52 as "RTL8218B (external)". Those ports only work if
u-boot initialize it (for example, loading initramfs image using one
of those ports). A patch to PHY detection is needed for full support.

The firmware recovery using U-Boot is broken for all DGS-1210 tested
devices as pressing RESET does not trigger it (only if pressed from a
running stock image)

UART pinout
-----------

[o]ooo|J14
 | ||`------ GND
 | |`------- RX
 | `-------- TX
 `---------- Vcc (3V3)

Installation using OEM upgrade
------------------------------

1. Make sure you are running OEM firmware in image2 slot (logged as admin):
   - > config firmware image_id 2 boot_up
   - > reboot
2. Install squashfs-factory_image1.bin to image1 using (logged as admin):
   - > download firmware_fromTFTP <tftpserver> factory_image1.bin
   - > config firmware image_id 1 boot_up
   - > reboot

Installation using serial interface
-----------------------------------

1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl839x-d-link_dgs-1210-52-initramfs-kernel.bin` command
5. Boot the image with `bootm` command

Once booted the initramfs, install the squashfs-sysupgrade.bin as a
normal OpenWrt system.

Dual-boot with stock firmware using writable u-boot-env
-------------------------------------------------------

From stock to OpenWrt / boot image 1 (CLI as admin):
   - > config firmware image_id 1 boot_up
   - > reboot

From OpenWrt to stock / boot image 2: (shell as root)
   - # fw_setenv bootcmd 'run addargs ; bootm 0xb4e80000'
   - # fw_setenv image '/dev/mtdblock7'
   - # reboot

Debrick using serial interface
------------------------------

1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
   detect the switch
3. Flash the firmware.

Back to stock firmware using dual-boot
--------------------------------------

If you have serial interface, you can change u-boot env vars
interrupting the boot process. If not but you are running OpenWrt, you
can dual-boot (as mentioned eariler) and skip to step 4:

1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Boot the image 2:
   - set image /dev/mtdblock7; run addargs; bootm 0xb4e80000
4. Once booted, log as admin and change the boot image to 2
   - > config firmware image_id 2 boot_up
   - > reboot
5. After the boot, flash image1 with the vendor image

Back to stock firmware using DNA
--------------------------------

1. From an OpenWrt:
   - # fw_setenv bootstop on
   - # reboot
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
   detect the switch
3. Flash the firmware.

It has been developed and tested on device with F3 revision.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2022-09-17 21:28:21 +02:00
Markus Stockhausen
9ed1a1138e realtek: align DT macros in RTL839X with RTL838X
Add a missing definition to the RTL839X DT.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
2022-09-17 21:28:21 +02:00
Markus Stockhausen
307e5cfc6e realtek: D-Link make common DT include generic
The D-Link DGS device tree was reorganized to better reflect the common
DT parts. The common include is named SOC specific (838X) and it seemed
like a good choice to add another common include in the future for the
RTL839X devices. From the current point of view this option is not really
needed.

1. The common part only includes data that matches RTL839X devices too.
2. The Panasonic DT structure avoids including the basic DTSI inside the
   common DTSI.

Taking simplicity of the Panasonic include logic and in perparation to
provide DGS-1210-52 support it makes sense to harmonize this.

- rename common include to reflect its content
- move the link to the root DTSI directly to the device specific DTS

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
2022-09-17 21:28:21 +02:00
Sungbo Eo
b201462c89 ramips: 5.15: add disabled PINCTRL_AW9523
Otherwise kernel 5.15 will fail to build on subtargets except for mt7621
that has enabled the config.
The disabled PINCTRL_AW9523 config disappears after a refresh, it needs
to be added back manually.

Fixes: 675cf75578 ("ramips: add config-5.15 for mt7620 subtarget")
Fixes: 001176994a ("ramips: add config-5.15 for mt76x8 subtarget")
Fixes: b9d9f33c33 ("ramips: add config-5.15 for rt288x subtarget")
Fixes: 0164dc0c25 ("ramips: add config-5.15 for rt305x subtarget")
Fixes: ef59da8669 ("ramips: add config-5.15 for rt3883 subtarget")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-09-18 03:09:19 +09:00
Sungbo Eo
bcd5d35dc0 ramips: 5.15: refresh subtarget kconfigs
Refresh config with `make kernel_oldconfig`.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-09-18 03:09:19 +09:00
Sungbo Eo
deb6f378bf ath79: specify factory.bin recipe for ASUS RP-AC51
Currently factory.bin image recipe of ASUS RP-AC51 is not specified
explicitly and is thus set to the leaked one from the device recipe
right above, i.e. ASUS PL-AC56. Fix it to avoid potential breakage.

Fixes: 416d4483e8 ("ath79: add support for ASUS RP-AC51")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-09-18 03:09:19 +09:00
Andre Heider
33e2115fe4 ltq-vdsl-app: rename to ltq-vdsl-vr9-app
This matches the scheme used by other target packages and will avoid
confusion with any future version.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-09-17 17:39:23 +02:00
John Audia
b77217d916 kernel: bump 5.10 to 5.10.143
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-17 14:16:37 +02:00
John Audia
fe209fa47d kernel: bump 5.15 to 5.15.68
All patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-17 14:16:37 +02:00
Koen Vandeputte
731646e13a kernel: mhi: backport upstream patch
This patch will print the name of the modem in the bootlog
during probing.

This allows to verify that the exact model was loaded and not some
generic type.

The only other way to do this is by enabling dynamic debugging
which is disabled by default in OpenWRT

Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
2022-09-16 09:17:24 +02:00
Daniel Golle
8010d3da03 mediatek: build USB XHCI support as module
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-14 20:26:58 +01:00
Olliver Schinagl
c4d030f24c
realtek: rtl838x: Fix ethernet polling timeout on probe
Due to an oversight we accidentally inverted the timeout check. This
patch corrects this.

Fixes: 9cec4a0ea4 ("realtek: Use built-in functionality for timeout loop")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[ wrap poll_timeout line to 80 char ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-09-14 18:23:06 +02:00
Petr Štetiar
67144f38e7 armvirt: make 5.15 kernel default
In order to begin testing of upcoming kernel.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-09-14 16:45:06 +02:00
Petr Štetiar
4ed850fcb1 malta: make 5.15 kernel default
In order to begin testing of upcoming kernel.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-09-14 16:45:06 +02:00
Wojciech Dubowik
016c934482 mpc85xx: Add 5.15 kernel as testing and fix configs
Build system: x86_64
Build-tested: generic
Run-tested: generic/TL-WDR4900 v1 board from TP-Link

Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@westermo.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [un-dmarc]
2022-09-14 16:45:06 +02:00
Wojciech Dubowik
00643b4584 mpc85xx: Copy over kernel 5.10 patches and config to 5.15
Split patches for better change visibility.

Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@westermo.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [un-dmarc, commit description]
2022-09-14 16:45:06 +02:00
Tomasz Maciej Nowak
df59c07fe9 tegra: add kernel 5.15 support
- refresh config
- disable suspend as it's pointless in the sope of OpenWrt
- enable CPU frequency scaling

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-14 16:45:06 +02:00
Tomasz Maciej Nowak
f8cd56def6 tegra: copy patches and config for kernel 5.15
Simple copy to better illustrate the forthcoming changes.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-14 16:45:06 +02:00
Rafał Miłecki
2f50c53f17 bcm53xx: update NVMEM driver for NVRAM
Include support for NVMEM cells.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-09-14 14:21:57 +02:00
Olliver Schinagl
9cec4a0ea4
realtek: Use built-in functionality for timeout loop
In commit 81e3017609 ("realtek: clean up rtl838x MDIO busy wait loop")
a hand-crafted loop was created, that nearly exactly replicate the
iopoll's `read_poll_timeout` functionality.

Use that instead.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-09-14 12:03:57 +02:00
Rosen Penev
cfd916065f
mt7621: fix Linksys E7350 GPIO
When converting this device to use both GMACs, I mistakenly removed
state_default, which prevented GPIO LEDs and keys from being used.

Fixes: f4eef5f2a1 ("ramips: add support for Linksys E7350")

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-09-13 22:19:10 +02:00
Rosen Penev
fb59070466
mt7621: fix Belkin RT1800 GPIO
When converting this device to use both GMACs, I mistakenly removed
state_default, which prevented GPIO LEDs and keys from being used.

Add back and and extra LEDs that were missing.

Tested all LEDs by turning them on.

Fixes: 26a6a6a60b ("ramips: add support for Belkin RT1800")

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-09-13 22:19:10 +02:00
Alexandru Gagniuc
01e2184c49 realtek: add support for TP-Link SG2210P
Add support for the TP-Link SG2210P switch. This is an RTL8380 based
switch with eight RJ-45 ports with 802.3af PoE, and two SFP ports.

This device shares the same board with the SG2008P and SG2008. To
model this, declare all the capabilities in the sg2xxx dtsi, and
disable unpopulated on the lower end models.

Specifications:
---------------
 - SoC:       Realtek RTL8380M
 - Flash:     32 MiB SPI flash (Vendor varies)
 - RAM:	      256 MiB (Vendor varies)
 - Ethernet:  8x 10/100/1000 Mbps with PoE (all ports)
              2x SFP ports
 - Buttons:   1x "Reset" button on front panel
 - Power:     53.5V DC barrel jack
 - UART:      1x serial header, unpopulated
 - PoE:       2x TI TPS23861 I2C PoE controller

Works:
------
  - (8) RJ-45 ethernet ports
  - (2) SFP ports (with caveats)
  - Switch functions
  - System LED

Not yet enabled:
----------------
  - Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
  - PoE LEDs

Enabling SFP ports:
-------------------

The SFP port control lines are hardwired, except for tx-disable. These
lines are controller by the RTL8231 in shift register mode. There is
no driver support for this yet.

However, to enable the lasers on SFP1 and SFP2 respectively:

    echo 0x0510ff00 > /sys/kernel/debug/rtl838x/led/led_p_en_ctrl
    echo      0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.26
    echo      0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.24

Install via serial console/tftp:
--------------------------------

The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.

The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.

Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWrt:

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"

Power on device, and stop boot by pressing any key.
Once the shell is active:
 1. Ground out the CLK (pin 16) of the ROM (U7)
 2. Select option "3. Start"
 3. Bootloader notes that "The kernel has been damaged!"
 4. Release CLK as sson as bootloader thinks image is corrupted.
 5. Bootloader enters automatic recovery -- details printed on console
 6. Watch as the bootloader flashes and boots OpenWrt.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[OpenWrt capitalisation in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-13 09:22:26 +02:00
Alexandru Gagniuc
ab2a4c1e01 realtek: rtl8380-tl-sg2xxx: use a single "firmware" partition
The "firmware" partition was assembled from two contiguous partitions.
This complexity is unnecessary. Instead of using mtd-concat over
"sys" and "usrimg1", simply declare the "firmware" partition to cover
the flash space instead.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2022-09-13 09:22:26 +02:00
Alexandru Gagniuc
d55c087390 realtek: tl-sg2xxx: read MAC address from nvmem-cells
The TP-Link RTL83xx based switches have their MAC address programmed
in the "para" partition. While in theory, the format of this partition
is dynamic, in practice, the MAC address appears to be located at a
consistent address. Thus, use nvmem-cells to read this MAC address.

The main MAC is required for deriving the MAC address of the switch
ports. Instead of reading it via mtd_get_mac_binary(), alias the
ethernet0 node as the label-mac-device, and use get_mac_label().

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2022-09-13 09:22:26 +02:00
Alexandru Gagniuc
5f026f1272 realtek: rtl838x: label switch port dts nodes
Although PHY nodes are labeled, the port nodes were not. Labeling of
ports is useful for 'status = "disabled"' ports, which is supported
since commit 9a7f17e11f ("realtek: ignore disabled switch ports")

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2022-09-13 09:22:26 +02:00
Alexandru Gagniuc
bc9dcfb1ce realtek: split TP-Link SG2000 series devicetree
The TP-Link TL-SG2008, TL-SG2008P, and TL-SG2210P use the same board.
The main difference is that some footprints are not populated in the
lower-end models. To model this with minimal duplication, move the
devicetree to a common dtsi, leaving out just the board name.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[remove port relabelling from commit message, already merged with commit
 18a2b29aa1 ("realtek: tl-sg2008p: fix labeling of lan ports")]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-13 09:22:26 +02:00
Hauke Mehrtens
9403810c02 toolchain: Select USE_SSTRIP with external musl toolchain
When we use the internal toolchain USE_SSTRIP will be selected by
default for musl libc and USE_STRIP when glibc is used. Do the same when
an external toolchain is used. USE_GLIBC will also be set for external
toolchain builds based on the EXTERNAL_TOOLCHAIN_LIBC_USE_GLIBC setting.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-09-12 23:16:22 +02:00
Daniel Golle
31a6605de0 mac80211: rt2x00: experimental improvements for MT7620 wifi
Serge Vasilugin reports:

To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
	https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
   set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
    a) RF and BBP regs never be corrected for this mode
    b) eLNA is driven the same way as ePA with mt7620's pin PA
	but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
	so I'm not sure that request for pa_pin in dts-file will be enough

First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA

Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
 35-40/30-35 Mbps for HT20
 65-70/60-65 Mbps for HT40

Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.

Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-12 21:37:08 +01:00
Sergei Burakov
2905ce3d64 ramips: add support for ZyXEL Keenetic 4G Rev.B Device
Specification:
SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
3x 10/100 Mbps Ethernet (2x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: Yes
8x LED, 2x button

Flash instruction:
Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-4g-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Sergei Burakov <senior.anonymous@mail.ru>
2022-09-13 01:01:52 +09:00
Daniel Golle
a46e91e8a1 mediatek: unset CONFIG_CMDLINE_OVERRIDE for all targets but mt7629
The newly introduced config symbol CONFIG_CMDLINE_OVERRIDE is only set
for mt7629 for now which breaks automated build on all other mediatek
subtargets. Make sure the symbol is configured as 'is not set' for all
remaining subtargets.

Fixes: c27279dc26 ("mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-12 14:10:26 +01:00
Yoonji Park
c27279dc26 mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)

Installation:
- Flash recovery image with TFTP recovery

Revert to stock firmware:
- Flash stock firmware with TFTP recovery

TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1

Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
2022-09-12 01:43:49 +01:00
Yoonji Park
49763d907b kernel: add support for mtdsplit-fit offset
Support devices that has vendor custom header before FIT image.

Some devices has vendor custom header before FIT image. In this case mtd-
split can not find FIT image and it results in rootfs mount failure.
Please refer iptime,a6004mx device for further examples.

Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
2022-09-12 01:43:49 +01:00
Shiji Yang
60384d8a74 mediatek: disable unsupported background radar detection
MT7915 requires an additional antenna for background radar scanning.
Disable this feature in the following devices that do not have a
separate DFS antenna:
  linksys,e8450
  ruijie,rg-ew3200gx-pro
  xiaomi,redmi-router-ax6s

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-09-12 00:14:02 +01:00
Shiji Yang
6cbcc34f50 ramips: disable unsupported background radar detection
Background radar detection is not supported on devices that
using MT7905, so disable this feature in the following devices:
  asus,rt-ax53u
  jcg,q20
  tplink,eap615-wall-v1
  xiaomi,mi-router-cr6606
  xiaomi,mi-router-cr6608
  xiaomi,mi-router-cr6609
  yuncore,ax820

Devices with MT7915 lacking a DFS antenna also do not support
background DFS:
  totolink,x5000r
  cudy,x6

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-09-12 00:14:02 +01:00
Jasper Scholte
4fcfb61ec9 ramips: use lzma-loader on Sitecom WLR-6000
Fixes the boot loader LZMA decompression issue:
LZMA ERROR 1 - must RESET board to recover

Signed-off-by: Jasper Scholte <NightNL@outlook.com>
2022-09-11 22:22:42 +02:00
Hauke Mehrtens
76fc277917 ath79: Make patches apply again
The patch adding support for LEDs connected to a reset controller did
not apply any more, refresh it on top of current master.

Fixes: 53fc987b25 ("generic: move ledbar driver from mediatek target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-09-11 22:17:47 +02:00
Will Moss
e22ca21daa ath79: add support for TP-Link TL-WR941ND v5
Specifications:
- SoC: ar9341
- RAM: 32M
- Flash: 4M
- Ethernet: 5x FE ports
- WiFi: ar9341-wmac

Flash instruction:
Upload generated factory firmware on vendor's web interface.

This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Buttons configuration is similar to TL-WR842ND v2 but both buttons are
active low.

Signed-off-by: Will Moss <willormos@gmail.com>
2022-09-11 22:00:22 +02:00
Nick French
20581ee8b5 ath79: add support for TP-Link Deco S4
Add support for TP-Link Deco S4 wifi router

The label refers to the device as S4R and the TP-Link firmware
site calls it the Deco S4 v2. (There does not appear to be a v1)

Hardware (and FCC id) are identical to the Deco M4R v2 but the
flash layout is ordered differently and the OEM firmware encrypts
some config parameters (including the label mac address) in flash

In order to set the encrypted mac address, the wlan's caldata
node is removed from the DTS so the mac can be decrypted with
the help of the uencrypt tool and patched into the wlan fw
via hotplug

Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR

UART serial access (115200N1) on board via solder pads:
RX = TP1 pad
TX = TP2 pad
GND = C201 (pad nearest board edge)

The device's bootloader and web gui will only accept images that
were signed using TP-Link's RSA key, however a memory safety bug
in the bootloader can be leveraged to install openwrt without
accessing the serial console. See developer forum S4 support page
for link to a "firmware" file that starts a tftp client, or you
may generate one on your own like this:
```
python - > deco_s4_faux_fw_tftp.bin <<EOF
import sys
from struct import pack

b = pack('>I', 0x00008000) + b'X'*16 + b"fw-type:" \
  + b'x'*256 + b"S000S001S002" + pack('>I', 0x80060200) \

b += b"\x00"*(0x200-len(b)) \
  + pack(">33I", *[0x3c0887fc, 0x35083ddc, 0xad000000, 0x24050000,
                   0x3c048006, 0x348402a0, 0x3c1987f9, 0x373947f4,
                   0x0320f809, 0x00000000, 0x24050000, 0x3c048006,
                   0x348402d0, 0x3c1987f9, 0x373947f4, 0x0320f809,
                   0x00000000, 0x24050000, 0x3c048006, 0x34840300,
                   0x3c1987f9, 0x373947f4, 0x0320f809, 0x00000000,
                   0x24050000, 0x3c048006, 0x34840400, 0x3c1987f9,
                   0x373947f4, 0x0320f809, 0x00000000, 0x1000fff1,
                   0x00000000])

b += b"\xff"*(0x2A0-len(b)) + b"setenv serverip 192.168.0.2\x00"
b += b"\xff"*(0x2D0-len(b)) + b"setenv ipaddr 192.168.0.1\x00"
b += b"\xff"*(0x300-len(b)) + b"tftpboot 0x81000000 initramfs-kernel.bin\x00"
b += b"\xff"*(0x400-len(b)) + b"bootm 0x81000000\x00"
b += b"\xff"*(0x8000-len(b))

sys.stdout.buffer.write(b)
EOF
```

Installation:
1. Run tftp server on pc with static ip 192.168.0.2
2. Place openwrt "initramfs-kernel.bin" image in tftp root dir
3. Connect pc to router ethernet port1
4. While holding in reset button on bottom of router, power on router
5. From pc access router webgui at http://192.168.0.1
6. Upload deco_s4_faux_fw_tftp.bin
7. Router will load and execture in-memory openwrt
8. Switch pc back to dhcp or static 192.168.1.x
9. Flash openwrt sysupgrade image via luci/ssh at 192.168.1.1

Revert to stock:
Press and hold reset button while powering device to start the
bootloader's recovery mode, where stock firmware can be uploaded
via web gui at 192.168.0.1

Please note that one additional non-github commits is also needed:
firmware-utils: add tplink-safeloader support for Deco S4

Signed-off-by: Nick French <nickfrench@gmail.com>
2022-09-11 21:54:00 +02:00
Michael Pratt
5df1b33298 ath79: add support for Senao Watchguard AP100
FCC ID: U2M-CAP2100AG

WatchGuard AP100 is an indoor wireless access point with
1 Gb ethernet port, dual-band but single-radio wireless,
internal antenna plates, and 802.3at PoE+

this board is a Senao device:
the hardware is equivalent to EnGenius EAP300 v2
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails

**Specification:**

  - AR9344 SOC          MIPS 74kc, 2.4 GHz AND 5 GHz WMAC, 2x2
  - AR8035-A EPHY       RGMII GbE with PoE+ IN
  - 25 MHz clock
  - 16 MB FLASH         mx25l12805d
  - 2x 64 MB RAM
  - UART console        J11, populated
  - GPIO watchdog       GPIO 16, 20 sec toggle
  - 2 antennas          5 dBi, internal omni-directional plates
  - 5 LEDs              power, eth0 link/data, 2G, 5G
  - 1 button            reset

**MAC addresses:**

  Label has no MAC
  Only one Vendor MAC address in flash at art 0x0

  eth0 ---- *:e5 art 0x0 -2
  phy0 ---- *:e5 art 0x0 -2

**Installation:**

  Method 1: OEM webpage

    use OEM webpage for firmware upgrade to upload factory.bin

  Method 2: root shell

    It may be necessary to use a Watchguard router to flash the image to the AP
    and / or to downgrade the software on the AP to access SSH
    For some Watchguard devices, serial console over UART is disabled.

  NOTE: DHCP is not enabled by default after flashing

**TFTP recovery:**

  reset button has no function at boot time
  only possible with modified uboot environment,
  (see commit message for Watchguard AP300)

**Return to OEM:**

  user should make backup of MTD partitions
  and write the backups back to mtd devices
  in order to revert to OEM reliably

  It may be possible to use sysupgrade
  with an OEM image as well...
  (not tested)

**OEM upgrade info:**

  The OEM upgrade script is at /etc/fwupgrade.sh

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

**Note on eth0 PLL-data:**

  The default Ethernet Configuration register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For AR934x series, the PLL registers for eth0
  can be see in the DTSI as 0x2c.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x1805002c 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

**Note on WatchGuard Magic string:**

  The OEM upgrade script is a modified version of
  the generic Senao sysupgrade script
  which is used on EnGenius devices.

  On WatchGuard boards produced by Senao,
  images are verified using a md5sum checksum of
  the upgrade image concatenated with a magic string.
  this checksum is then appended to the end of the final image.

  This variable does not apply to all the senao devices
  so set to null string as default

Tested-by: Steve Wheeler <stephenw10@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-09-11 21:54:00 +02:00
Michael Pratt
9f6e247854 ath79: add support for Senao WatchGuard AP200
FCC ID: U2M-CAP4200AG

WatchGuard AP200 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

this board is a Senao device:
the hardware is equivalent to EnGenius EAP600
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails

**Specification:**

  - AR9344 SOC		MIPS 74kc, 2.4 GHz WMAC, 2x2
  - AR9382 WLAN		PCI card 168c:0030, 5 GHz, 2x2, 26dBm
  - AR8035-A EPHY	RGMII GbE with PoE+ IN
  - 25 MHz clock
  - 16 MB FLASH		mx25l12805d
  - 2x 64 MB RAM
  - UART console        J11, populated
  - GPIO watchdog       GPIO 16, 20 sec toggle
  - 4 antennas          5 dBi, internal omni-directional plates
  - 5 LEDs              power, eth0 link/data, 2G, 5G
  - 1 button            reset

**MAC addresses:**

  Label has no MAC
  Only one Vendor MAC address in flash at art 0x0

  eth0 ---- *:be art 0x0 -2
  phy1 ---- *:bf art 0x0 -1
  phy0 ---- *:be art 0x0 -2

**Installation:**

  Method 1: OEM webpage

    use OEM webpage for firmware upgrade to upload factory.bin

  Method 2: root shell

    It may be necessary to use a Watchguard router to flash the image to the AP
    and / or to downgrade the software on the AP to access SSH
    For some Watchguard devices, serial console over UART is disabled.

  NOTE: DHCP is not enabled by default after flashing

**TFTP recovery:**

  reset button has no function at boot time
  only possible with modified uboot environment,
  (see commit message for Watchguard AP300)

**Return to OEM:**

  user should make backup of MTD partitions
  and write the backups back to mtd devices
  in order to revert to OEM reliably

  It may be possible to use sysupgrade
  with an OEM image as well...
  (not tested)

**OEM upgrade info:**

  The OEM upgrade script is at /etc/fwupgrade.sh

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

**Note on eth0 PLL-data:**

  The default Ethernet Configuration register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For AR934x series, the PLL registers for eth0
  can be see in the DTSI as 0x2c.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x1805002c 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

**Note on WatchGuard Magic string:**

  The OEM upgrade script is a modified version of
  the generic Senao sysupgrade script
  which is used on EnGenius devices.

  On WatchGuard boards produced by Senao,
  images are verified using a md5sum checksum of
  the upgrade image concatenated with a magic string.
  this checksum is then appended to the end of the final image.

  This variable does not apply to all the senao devices
  so set to null string as default

Tested-by: Steve Wheeler <stephenw10@gmail.com>
Tested-by: John Delaney <johnd@ankco.net>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-09-11 21:54:00 +02:00
Michael Pratt
146aaeafb7 ath79: add support for Senao WatchGuard AP300
FCC ID: Q6G-AP300

WatchGuard AP300 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails

**Specification:**

  - QCA9558 SOC		MIPS 74kc, 2.4 GHz WMAC, 3x3
  - QCA9880 WLAN	PCI card 168c:003c, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 32 MB FLASH		S25FL512S
  - 2x 64 MB RAM	NT5TU32M16
  - UART console	J10, populated
  - GPIO watchdog	GPIO 16, 20 sec toggle
  - 6 antennas		5 dBi, internal omni-directional plates
  - 5 LEDs		power, eth0 link/data, 2G, 5G
  - 1 button		reset

**MAC addresses:**

  MAC address labeled as ETH
  Only one Vendor MAC address in flash at art 0x0

  eth0 ETH  *:3c art 0x0
  phy1 ---- *:3d ---
  phy0 ---- *:3e ---

**Serial console access:**

  For this board, its not certain whether UART is possible
  it is likely that software is blocking console access

  the RX line on the board for UART is shorted to ground by resistor R176
  the resistors R175 and R176 are next to the UART RX pin at J10

  however console output is garbage even after this fix

**Installation:**

  Method 1: OEM webpage

    use OEM webpage for firmware upgrade to upload factory.bin

  Method 2: root shell access

    downgrade XTM firewall to v2.0.0.1
    downgrade AP300 firmware: v1.0.1
    remove / unpair AP from controller
    perform factory reset with reset button
    connect ethernet to a computer
    login to OEM webpage with default address / pass: wgwap
    enable SSHD in OEM webpage settings
    access root shell with SSH as user 'root'
    modify uboot environment to automatically try TFTP at boot time
    (see command below)

    rename initramfs-kernel.bin to test.bin
    load test.bin over TFTP (see TFTP recovery)
    (optionally backup all mtdblocks to have flash backup)
    perform a sysupgrade with sysupgrade.bin

  NOTE: DHCP is not enabled by default after flashing

**TFTP recovery:**

  server ip: 192.168.1.101

  reset button seems to do nothing at boot time...
  only possible with modified uboot environment,
  running this command in the root shell:

  fw_setenv bootcmd 'if ping 192.168.1.101; then tftp 0x82000000 test.bin && bootm 0x82000000; else bootm 0x9f0a0000; fi'

  and verify that it is correct with

  fw_printenv

  then, before boot, the device will attempt TFTP from 192.168.1.101
  looking for file 'test.bin'

  to return uboot environment to normal:

  fw_setenv bootcmd 'bootm 0x9f0a0000'

**Return to OEM:**

  user should make backup of MTD partitions
  and write the backups back to mtd devices
  in order to revert to OEM
  (see installation method 2)

  It may be possible to use sysupgrade
  with an OEM image as well...
  (not tested)

**OEM upgrade info:**

  The OEM upgrade script is at /etc/fwupgrade.sh

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

**Note on eth0 PLL-data:**

  The default Ethernet Configuration register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

**Note on WatchGuard Magic string:**

  The OEM upgrade script is a modified version of
  the generic Senao sysupgrade script
  which is used on EnGenius devices.

  On WatchGuard boards produced by Senao,
  images are verified using a md5sum checksum of
  the upgrade image concatenated with a magic string.
  this checksum is then appended to the end of the final image.

  This variable does not apply to all the senao devices
  so set to null string as default

Tested-by: Alessandro Kornowski <ak@wski.org>
Tested-by: John Wagner <john@wagner.us.org>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-09-11 21:54:00 +02:00
Michael Pratt
c107506883 ath79: fix RGMII delay for ar9344 Senao APs
after some trial and error, it was discovered
that by setting TX only delay on the AR8035 PHY
that setting GMAC registers is no longer necessary.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-09-11 21:54:00 +02:00
Michael Pratt
513f9855e9 ath79: rename an engenius DTSI to generic senao name
Other vendors can use this DTSI, for example, WatchGuard
there are likely several brands that use the same board design
because of outsourcing hardware from Senao.

For example, Watchguard AP300
has the same hardware as Engenius EAP600
so we use ar9344_engenius_exx600.dtsi for that

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-09-11 21:54:00 +02:00
Daniel Golle
0b5cf952cf mediatek: fix ledbar of UniFi 6 LR when running custom U-Boot
The RGB LED of the UniFi 6 LR v1 doesn't work when using the Openwrt-
built U-Boot. This is because the vendor loader resets the ledbar
controller while our U-Boot doesn't care.
Add reset-gpio so the ledbar driver in Linux will always reset the
ledbar controller.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-11 20:26:42 +01:00
Sven Wegener
820f0c07c5 ramips: add support for Ubiquiti UniFi FlexHD
Hardware
--------

- SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash
- Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4)
- Bluetooth: CSR8811 (internal USB, install kmod-bluetooth)

Installation
------------

1. Connect to the booted device at 192.168.1.20 using username/password
   "ubnt".

2. Update the bootloader environment.

   $ fw_setenv devmode TRUE
   $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
     fdt rm /signature; bootubnt"
   $ fw_setenv bootcmd "run boot_openwrt"

3. Transfer the OpenWrt sysupgrade image to the device using SCP.

4. Check the mtd partition number for bs / kernel0 / kernel1

   $ cat /proc/mtd

5. Set the bootselect flag to boot from kernel0

   $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4

6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1

   $ dd if=openwrt.bin of=/dev/mtdblock6
   $ dd if=openwrt.bin of=/dev/mtdblock7

7. Reboot the device. It should boot into OpenWrt.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:42 +01:00
Sven Wegener
53fc987b25 generic: move ledbar driver from mediatek target
This moves the ledbar driver to generic, to be also used by the ramips target.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:42 +01:00
Sven Wegener
76198e8f09 mediatek: add led count
The LEDs connected to the MCU are so-called smart LEDs and their signal is
daisy-chained. Because of this, the MCU needs to be told how many LEDs are
connected. It also means the LEDs could be individually controlled, if the MCU
has a command for this.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:42 +01:00
Sven Wegener
013a956f08 mediatek: add initialization after reset
During GPIO initialization the pin state flips and triggers a reset of
the ledbar MCU. It needs to be moved through an initialization sequence
before working correctly.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:42 +01:00
Sven Wegener
84e4bbf5f0 mediatek: add support for reset gpio
Some versions of the ledbar MCU have a reset pin. It needs to be
correctly initialized or we might keep the MCU in reset state.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:42 +01:00
Sven Wegener
7c852e7df5 mediatek: support reading more than one byte of response
There are commands that return more than one byte of response.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:41 +01:00
Sven Wegener
e9a22ce253 mediatek: cast literal value to char
Or the comparison against a signed char is always true, because the
literal 0xaa is treated as an unsigned int, to which the signed char is
casted during comparison. 0xaa is above the positive values of a signed
char and negative signed char values result in values larger than 0xaa
when casted to unsigned int.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:41 +01:00
Sven Wegener
c4f9f9b44c mediatek: correctly log i2c response
The read response is in the i2c_response variable. Also use %hhx format,
because we're dealing with a single char.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:41 +01:00
Sven Wegener
a188356484 mediatek: remove gpiod_direction_output()
It's already set to output with GPIOD_OUT_LOW.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:41 +01:00
Sven Wegener
56c2d15587 mediatek: do not use gpiod_set_raw_value()
The polarity of the signal is set in the device dts.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
2022-09-11 20:26:41 +01:00
David Bauer
470ca65bda ipq40xx: add GL-AP1300 label-mac-device
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-11 16:24:11 +02:00
David Bauer
4d014a7bd6 ipq40xx: add WAN LED mapping for GL-AP1300
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-11 15:53:49 +02:00
David Santamaría Rogado
548db4980f
ramips: ASUS RT-ACx5P phy[01]radio to phy[01]tpt
phy[01]radio leaves the leds always on, if they are set through sysfs the leds
get off.
Set the triggers to phy[01]tpt to make them work.

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
2022-09-11 11:42:03 +02:00
Daniel Golle
a9dda40fe2 oxnas: add testing support for Linux 5.15
Rebase patches and port SATA driver to work with Linux > 5.13.
Tested on Shuttle KD-20.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-11 02:49:28 +01:00
Daniel Golle
ef59da8669 ramips: add config-5.15 for rt3883 subtarget
Add Kernel config for testing Linux 5.15 for the rt3883 subtarget.
Compile tested only.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-11 02:49:28 +01:00
Daniel Golle
0164dc0c25 ramips: add config-5.15 for rt305x subtarget
Add Kernel config for testing Linux 5.15 for the rt305x subtarget.
Tested on ZyXEL NBG-419N, works but bad wireless performance.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-11 02:49:28 +01:00
Daniel Golle
b9d9f33c33 ramips: add config-5.15 for rt288x subtarget
Add Kernel config for testing Linux 5.15 for the rt288x subtarget.
Compile tested only.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-11 02:49:28 +01:00
Daniel Golle
001176994a ramips: add config-5.15 for mt76x8 subtarget
Add Kernel config for testing Linux 5.15 for the mt76x8 subtarget.
Compile tested only.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-11 02:49:28 +01:00
Rui Salvaterra
05158082f6 kernel: add and enable MGLRU for Linux 5.15
Backport a preliminary version of Yu Zhao's multi-generational LRU, for
improved memory management. Refresh the patches while at it.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-09-11 02:49:28 +01:00
Gregory Detal
0be1b78856 ipq40xx: cellc_rtl30vw: fix imagebuilder generation
The image build process was modifying the generated IMAGE_KERNEL to
append rootfs information (crc). This caused:
 - sysupgrade & factory images to contain 2 times the root.squashfs
   information due to both modifying the same IMAGE_KERNEL.
 - the generated imagebuilder to contain an erroneous IMAGE_KERNEL that
   contained references to an unexisting root.squashfs (the one from
   previous cause). The RTL30VW wasn't therefore able to boot the
   generated images as they contained checksums from non existing rootfs.

This commit makes sure to use a temporary IMAGE_KERNEL to append the
rootfs information for both factory and sysupgrade images.

Fixes: #10511
Signed-off-by: Gregory Detal <gregory.detal@tessares.net>
2022-09-11 01:36:25 +02:00
Lech Perczak
f1d112ee5a ath79: support Ruckus ZoneFlex 7321
Ruckus ZoneFlex 7321 is a dual-band, single radio 802.11n 2x2 MIMO enterprise
access point. It is very similar to its bigger brother, ZoneFlex 7372.

Hardware highligts:
- CPU: Atheros AR9342 SoC at 533 MHz
- RAM: 64MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi: AR9342 built-in dual-band 2x2 MIMO radio
- Ethernet: single Gigabit Ethernet port through AR8035 gigabit PHY
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the 7321-U variant.

Serial console: 115200-8-N-1 on internal H1 header.
Pinout:

H1 ----------
   |1|x3|4|5|
   ----------

Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX

JTAG: Connector H5, unpopulated, similar to MIPS eJTAG, standard,
but without the key in pin 12 and not every pin routed:

------- H5
|1 |2 |
-------
|3 |4 |
-------
|5 |6 |
-------
|7 |8 |
-------
|9 |10|
-------
|11|12|
-------
|13|14|
-------

3 - TDI
5 - TDO
7 - TMS
9 - TCK
2,4,6,8,10 - GND
14 - Vref
1,11,12,13 - Not connected

Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
  adapter, TFTP server,  and removing a single T10 screw,
  but with much less manual steps, and is generally recommended, being
  safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
  work on some rare versions of stock firmware. A more involved, and
  requires installing `mkenvimage` from u-boot-tools package if you
  choose to rebuild your own environment, but can be used without
  disassembly or removal from installation point, if you have the
  credentials.
  If for some reason, size of your sysupgrade image exceeds 13312kB,
  proceed with method [1]. For official images this is not likely to
  happen ever.

[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
   does not back-power the board, otherwise it will fail to boot.

1. Power-on the board. Then quickly connect serial converter to PC and
   hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
   you'll enter U-boot shell. Then skip to point 3.
   Connection parameters are 115200-8-N-1.

2. Allow the board to boot.  Press the reset button, so the board
   reboots into U-boot again and go back to point 1.

3. Set the "bootcmd" variable to disable the dual-boot feature of the
   system and ensure that uImage is loaded. This is critical step, and
   needs to be done only on initial installation.

   > setenv bootcmd "bootm 0x9f040000"
   > saveenv

4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:

   > setenv serverip 192.168.1.2
   > setenv ipaddr 192.168.1.1
   > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7321-initramfs-kernel.bin
   > bootm 0x81000000

5. Optional, but highly recommended: back up contents of "firmware" partition:

   $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7321_fw1_backup.bin
   $ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7321_fw2_backup.bin

6. Copy over sysupgrade image, and perform actual installation. OpenWrt
   shall boot from flash afterwards:

   $ ssh root@192.168.1.1
   # sysupgrade -n openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin

[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
   it boots, hold the reset button near Ethernet connectors for 5
   seconds.

1. Connect the device to the network. It will acquire address over DHCP,
   so either find its address using list of DHCP leases by looking for
   label MAC address, or try finding it by scanning for SSH port:

   $ nmap 10.42.0.0/24 -p22

   From now on, we assume your computer has address 10.42.0.1 and the device
   has address 10.42.0.254.

2. Set up a TFTP server on your computer. We assume that TFTP server
   root is at /srv/tftp.

3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
   frmware is pretty ancient and requires enabling HMAC-MD5.

   $ ssh 10.42.0.254 \
   -o UserKnownHostsFile=/dev/null \
   -o StrictHostKeyCheking=no \
   -o MACs=hmac-md5

   Login. User is "super", password is "sp-admin".
   Now execute a hidden command:

   Ruckus

   It is case-sensitive. Copy and paste the following string,
   including quotes. There will be no output on the console for that.

   ";/bin/sh;"

   Hit "enter". The AP will respond with:

   grrrr
   OK

   Now execute another hidden command:

   !v54!

   At "What's your chow?" prompt just hit "enter".
   Congratulations, you should now be dropped to Busybox shell with root
   permissions.

4. Optional, but highly recommended: backup the flash contents before
   installation. At your PC ensure the device can write the firmware
   over TFTP:

   $ sudo touch /srv/tftp/ruckus_zf7321_firmware{1,2}.bin
   $ sudo chmod 666 /srv/tftp/ruckus_zf7321_firmware{1,2}.bin

   Locate partitions for primary and secondary firmware image.
   NEVER blindly copy over MTD nodes, because MTD indices change
   depending on the currently active firmware, and all partitions are
   writable!

   # grep rcks_wlan /proc/mtd

   Copy over both images using TFTP, this will be useful in case you'd
   like to return to stock FW in future. Make sure to backup both, as
   OpenWrt uses bot firmwre partitions for storage!

   # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7321_firmware1.bin -p 10.42.0.1
   # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7321_firmware2.bin -p 10.42.0.1

   When the command finishes, copy over the dump to a safe place for
   storage.

   $ cp /srv/tftp/ruckus_zf7321_firmware{1,2}.bin ~/

5. Ensure the system is running from the BACKUP image, i.e. from
   rcks_wlan.bkup partition or "image 2". Otherwise the installation
   WILL fail, and you will need to access mtd0 device to write image
   which risks overwriting the bootloader, and so is not covered here
   and not supported.

   Switching to backup firmware can be achieved by executing a few
   consecutive reboots of the device, or by updating the stock firmware. The
   system will boot from the image it was not running from previously.
   Stock firmware available to update was conveniently dumped in point 4 :-)

6. Prepare U-boot environment image.
   Install u-boot-tools package. Alternatively, if you build your own
   images, OpenWrt provides mkenvimage in host staging directory as well.
   It is recommended to extract environment from the device, and modify
   it, rather then relying on defaults:

   $ sudo touch /srv/tftp/u-boot-env.bin
   $ sudo chmod 666 /srv/tftp/u-boot-env.bin

   On the device, find the MTD partition on which environment resides.
   Beware, it may change depending on currently active firmware image!

   # grep u-boot-env /proc/mtd

   Now, copy over the partition

   # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1

   Store the stock environment in a safe place:

   $ cp /srv/tftp/u-boot-env.bin ~/

   Extract the values from the dump:

   $ strings u-boot-env.bin | tee u-boot-env.txt

   Now clean up the debris at the end of output, you should end up with
   each variable defined once. After that, set the bootcmd variable like
   this:

   bootcmd=bootm 0x9f040000

   You should end up with something like this:

bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup)
mtdids=nor0=ar7100-nor0
bootdelay=2
ethact=eth0
filesize=78a000
fileaddr=81000000
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=10.0.0.1
serverip=10.0.0.5
stdin=serial
stdout=serial
stderr=serial

   These are the defaults, you can use most likely just this as input to
   mkenvimage.

   Now, create environment image and copy it over to TFTP root:

   $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
   $ sudo cp u-boot-env.bin /srv/tftp

   This is the same image, gzipped and base64-encoded:

H4sIAAAAAAAAA+3QQW7TQBQAUF8EKRtQI6XtJDS0VJoN4gYcAE3iCbWS2MF2Sss1ORDYqVq6YMEB3rP0
Z/7Yf+aP3/56827VNP16X8Zx3E/Cw8dNuAqDYlxI7bcurpu6a3Y59v3jlzCbz5eLECbt8HbT9Y+HHLvv
x9TdbbpJVVd9vOxWVX05TotVOpZt6nN8qilyf5fKso3hIYTb8JDSEFarIazXQyjLIeRc7PvykNq+iy+T
1F7PQzivmzbcLpYftmfH87G56Wz+/v18sT1r19vu649dqi/2qaqns0W4utmelalPm27I/lac5/p+OluO
NZ+a1JaTz8M3/9hmtT0epmMjVdnF8djXLZx+TJl36TEuTlda93EYQrGpdrmrfuZ4fZPGHzjmp/vezMNJ
MV6n6qumPm06C+MRZb6vj/v4Mk/7HJ+6LarDqXweLsZnXnS5vc9tdXheWRbd0GIdh/Uq7cakOfavsty2
z1nxGwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAD+1x9eTkHLAAAEAA==

7. Perform actual installation. Copy over OpenWrt sysupgrade image to
   TFTP root:

   $ sudo cp openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin /srv/tftp

   Now load both to the device over TFTP:

   # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
   # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin -g 10.42.0.1

   Vverify checksums of both images to ensure the transfer over TFTP
   was completed:

   # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin

   And compare it against source images:

   $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin

   Locate MTD partition of the primary image:

   # grep rcks_wlan.main /proc/mtd

   Now, write the images in place. Write U-boot environment last, so
   unit still can boot from backup image, should power failure occur during
   this. Replace MTD placeholders with real MTD nodes:

   # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
   # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>

   Finally, reboot the device. The device should directly boot into
   OpenWrt. Look for the characteristic power LED blinking pattern.

   # reboot -f

   After unit boots, it should be available at the usual 192.168.1.1/24.

Return to factory firmware:

1. Boot into OpenWrt initramfs as for initial installation. To do that
   without disassembly, you can write an initramfs image to the device
   using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
   fw_setenv bootcmd ""
3. Write factory images downloaded from manufacturer website into
   fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
   before installation:
   mtd write ruckus_zf7321_fw1_backup.bin /dev/mtd1
   mtd write ruckus_zf7321_fw2_backup.bin /dev/mtd5
4. Reboot the system, it should load into factory firmware again.

Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
  partitions for storage using mtd-concat, and uImage format is used to
  actually boot the system, which rules out the dual-boot capability.
- The 5GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
  OpenWrt by choice.
  It is controlled by data in the top 64kB of RAM which is unmapped,
  to avoid   the interference in the boot process and accidental
  switch to the inactive image, although boot script presence in
  form of "bootcmd" variable should prevent this entirely.
- U-boot disables JTAG when starting. To re-enable it, you need to
  execute the following command before booting:
  mw.l 1804006c 40
  And also you need to disable the reset button in device tree if you
  intend to debug Linux, because reset button on GPIO0 shares the TCK
  pin.
- On some versions of stock firmware, it is possible to obtain root shell,
  however not much is available in terms of debugging facitilies.
  1. Login to the rkscli
  2. Execute hidden command "Ruckus"
  3. Copy and paste ";/bin/sh;" including quotes. This is required only
     once, the payload will be stored in writable filesystem.
  4. Execute hidden command "!v54!". Press Enter leaving empty reply for
     "What's your chow?" prompt.
  5. Busybox shell shall open.
  Source: https://alephsecurity.com/vulns/aleph-2019014

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-09-11 01:36:25 +02:00
Lech Perczak
59cb4dc91d ath79: support Ruckus ZoneFlex 7372
Ruckus ZoneFlex 7372 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point.

Ruckus ZoneFlex 7352 is also supported, lacking the 5GHz radio part.

Hardware highligts:
- CPU: Atheros AR9344 SoC at 560 MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344 built-in 2x2 MIMO radio
- Wi-Fi 5Ghz: AR9582 2x2 MIMO radio (Only in ZF7372)
- Antennas:
  - Separate internal active antennas with beamforming support on both
    bands with 7 elements per band, each controlled by 74LV164 GPIO
    expanders, attached to GPIOs of each radio.
  - Two dual-band external RP-SMA antenna connections on "7372-E"
    variant.
- Ethernet 1: single Gigabit Ethernet port through AR8035 gigabit PHY
- Ethernet 2: single Fast Ethernet port through AR9344 built-in switch
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on "-U" variants.

The same image should support:
- ZoneFlex 7372E (variant with external antennas, without beamforming
  capability)
- ZoneFlex 7352 (single-band, 2.4GHz-only variant).

which are based on same baseboard (codename St. Bernard),
with different populated components.

Serial console: 115200-8-N-1 on internal H1 header.
Pinout:

H1
---
|5|
---
|4|
---
|3|
---
|x|
---
|1|
---

Pin 5 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX

JTAG: Connector H2, similar to MIPS eJTAG, standard,
but without the key in pin 12 and not every pin routed:

------- H2
|1 |2 |
-------
|3 |4 |
-------
|5 |6 |
-------
|7 |8 |
-------
|9 |10|
-------
|11|12|
-------
|13|14|
-------

3 - TDI
5 - TDO
7 - TMS
9 - TCK
2,4,6,8,10 - GND
14 - Vref
1,11,12,13 - Not connected

Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
  adapter, TFTP server,  and removing a single T10 screw,
  but with much less manual steps, and is generally recommended, being
  safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
  work on some rare versions of stock firmware. A more involved, and
  requires installing `mkenvimage` from u-boot-tools package if you
  choose to rebuild your own environment, but can be used without
  disassembly or removal from installation point, if you have the
  credentials.
  If for some reason, size of your sysupgrade image exceeds 13312kB,
  proceed with method [1]. For official images this is not likely to
  happen ever.

[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
   does not back-power the board, otherwise it will fail to boot.

1. Power-on the board. Then quickly connect serial converter to PC and
   hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
   you'll enter U-boot shell. Then skip to point 3.
   Connection parameters are 115200-8-N-1.

2. Allow the board to boot.  Press the reset button, so the board
   reboots into U-boot again and go back to point 1.

3. Set the "bootcmd" variable to disable the dual-boot feature of the
   system and ensure that uImage is loaded. This is critical step, and
   needs to be done only on initial installation.

   > setenv bootcmd "bootm 0x9f040000"
   > saveenv

4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:

   > setenv serverip 192.168.1.2
   > setenv ipaddr 192.168.1.1
   > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7372-initramfs-kernel.bin
   > bootm 0x81000000

5. Optional, but highly recommended: back up contents of "firmware" partition:

   $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7372_fw1_backup.bin
   $ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7372_fw2_backup.bin

6. Copy over sysupgrade image, and perform actual installation. OpenWrt
   shall boot from flash afterwards:

   $ ssh root@192.168.1.1
   # sysupgrade -n openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin

[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
   it boots, hold the reset button near Ethernet connectors for 5
   seconds.

1. Connect the device to the network. It will acquire address over DHCP,
   so either find its address using list of DHCP leases by looking for
   label MAC address, or try finding it by scanning for SSH port:

   $ nmap 10.42.0.0/24 -p22

   From now on, we assume your computer has address 10.42.0.1 and the device
   has address 10.42.0.254.

2. Set up a TFTP server on your computer. We assume that TFTP server
   root is at /srv/tftp.

3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
   frmware is pretty ancient and requires enabling HMAC-MD5.

   $ ssh 10.42.0.254 \
   -o UserKnownHostsFile=/dev/null \
   -o StrictHostKeyCheking=no \
   -o MACs=hmac-md5

   Login. User is "super", password is "sp-admin".
   Now execute a hidden command:

   Ruckus

   It is case-sensitive. Copy and paste the following string,
   including quotes. There will be no output on the console for that.

   ";/bin/sh;"

   Hit "enter". The AP will respond with:

   grrrr
   OK

   Now execute another hidden command:

   !v54!

   At "What's your chow?" prompt just hit "enter".
   Congratulations, you should now be dropped to Busybox shell with root
   permissions.

4. Optional, but highly recommended: backup the flash contents before
   installation. At your PC ensure the device can write the firmware
   over TFTP:

   $ sudo touch /srv/tftp/ruckus_zf7372_firmware{1,2}.bin
   $ sudo chmod 666 /srv/tftp/ruckus_zf7372_firmware{1,2}.bin

   Locate partitions for primary and secondary firmware image.
   NEVER blindly copy over MTD nodes, because MTD indices change
   depending on the currently active firmware, and all partitions are
   writable!

   # grep rcks_wlan /proc/mtd

   Copy over both images using TFTP, this will be useful in case you'd
   like to return to stock FW in future. Make sure to backup both, as
   OpenWrt uses bot firmwre partitions for storage!

   # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7372_firmware1.bin -p 10.42.0.1
   # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7372_firmware2.bin -p 10.42.0.1

   When the command finishes, copy over the dump to a safe place for
   storage.

   $ cp /srv/tftp/ruckus_zf7372_firmware{1,2}.bin ~/

5. Ensure the system is running from the BACKUP image, i.e. from
   rcks_wlan.bkup partition or "image 2". Otherwise the installation
   WILL fail, and you will need to access mtd0 device to write image
   which risks overwriting the bootloader, and so is not covered here
   and not supported.

   Switching to backup firmware can be achieved by executing a few
   consecutive reboots of the device, or by updating the stock firmware. The
   system will boot from the image it was not running from previously.
   Stock firmware available to update was conveniently dumped in point 4 :-)

6. Prepare U-boot environment image.
   Install u-boot-tools package. Alternatively, if you build your own
   images, OpenWrt provides mkenvimage in host staging directory as well.
   It is recommended to extract environment from the device, and modify
   it, rather then relying on defaults:

   $ sudo touch /srv/tftp/u-boot-env.bin
   $ sudo chmod 666 /srv/tftp/u-boot-env.bin

   On the device, find the MTD partition on which environment resides.
   Beware, it may change depending on currently active firmware image!

   # grep u-boot-env /proc/mtd

   Now, copy over the partition

   # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1

   Store the stock environment in a safe place:

   $ cp /srv/tftp/u-boot-env.bin ~/

   Extract the values from the dump:

   $ strings u-boot-env.bin | tee u-boot-env.txt

   Now clean up the debris at the end of output, you should end up with
   each variable defined once. After that, set the bootcmd variable like
   this:

   bootcmd=bootm 0x9f040000

   You should end up with something like this:

bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
bootdelay=2
mtdids=nor0=ar7100-nor0
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup)
ethact=eth0
filesize=1000000
fileaddr=81000000
ipaddr=192.168.0.7
serverip=192.168.0.51
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
stdin=serial
stdout=serial
stderr=serial

   These are the defaults, you can use most likely just this as input to
   mkenvimage.

   Now, create environment image and copy it over to TFTP root:

   $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
   $ sudo cp u-boot-env.bin /srv/tftp

   This is the same image, gzipped and base64-encoded:

H4sIAAAAAAAAA+3QTW7TQBQAYB+AQ2TZSGk6Tpv+SbNBrNhyADSJHWolsYPtlJaDcAWOCXaqQhdIXOD7
Fm/ee+MZ+/nHu58fV03Tr/dFHNf9JDzdbcJVGGRjI7Vfurhu6q7ZlbHvnz+FWZ4vFyFM2mF30/XPhzJ2
X4+pe9h0k6qu+njRrar6YkyzVToWberL+HImK/uHVBRtDE8h3IenlIawWg1hvR5CUQyhLE/vLcpdeo6L
bN8XVdHFumlDTO1NHsL5mI/9Q2r7Lv5J3uzeL5bX27Pj+XjRdJZfXuaL7Vm73nafv+1SPd+nqp7OFuHq
dntWpD5tuqH6e+K8rB+ns+V45n2T2mLyYXjmH9estsfD9DTSuo/DErJNtSu76vswbjg5NU4D3752qsOp
zu8W8/z6dh7mN1lXto9lWx3eNJd5Ng5V9VVTn2afnSYuysf6uI9/8rQv48s3Z93wn+o4XFWl3Vg0x/5N
Vbbta5X9AgAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAID/+Q2Z/B7cAAAEAA==

7. Perform actual installation. Copy over OpenWrt sysupgrade image to
   TFTP root:

   $ sudo cp openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin /srv/tftp

   Now load both to the device over TFTP:

   # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
   # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin -g 10.42.0.1

   Verify checksums of both images to ensure the transfer over TFTP
   was completed:

   # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin

   And compare it against source images:

   $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin

   Locate MTD partition of the primary image:

   # grep rcks_wlan.main /proc/mtd

   Now, write the images in place. Write U-boot environment last, so
   unit still can boot from backup image, should power failure occur during
   this. Replace MTD placeholders with real MTD nodes:

   # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
   # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>

   Finally, reboot the device. The device should directly boot into
   OpenWrt. Look for the characteristic power LED blinking pattern.

   # reboot -f

   After unit boots, it should be available at the usual 192.168.1.1/24.

Return to factory firmware:

1. Boot into OpenWrt initramfs as for initial installation. To do that
   without disassembly, you can write an initramfs image to the device
   using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
   fw_setenv bootcmd ""
3. Write factory images downloaded from manufacturer website into
   fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
   before installation:
   mtd write ruckus_zf7372_fw1_backup.bin /dev/mtd1
   mtd write ruckus_zf7372_fw2_backup.bin /dev/mtd5
4. Reboot the system, it should load into factory firmware again.

Quirks and known issues:
- This is first device in ath79 target to support link state reporting
  on FE port attached trough the built-in switch.
- Flash layout is changed from the factory, to use both firmware image
  partitions for storage using mtd-concat, and uImage format is used to
  actually boot the system, which rules out the dual-boot capability.
  The 5GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
  OpenWrt by choice.
  It is controlled by data in the top 64kB of RAM which is unmapped,
  to avoid   the interference in the boot process and accidental
  switch to the inactive image, although boot script presence in
  form of "bootcmd" variable should prevent this entirely.
- U-boot disables JTAG when starting. To re-enable it, you need to
  execute the following command before booting:
  mw.l 1804006c 40
  And also you need to disable the reset button in device tree if you
  intend to debug Linux, because reset button on GPIO0 shares the TCK
  pin.
- On some versions of stock firmware, it is possible to obtain root shell,
  however not much is available in terms of debugging facitilies.
  1. Login to the rkscli
  2. Execute hidden command "Ruckus"
  3. Copy and paste ";/bin/sh;" including quotes. This is required only
     once, the payload will be stored in writable filesystem.
  4. Execute hidden command "!v54!". Press Enter leaving empty reply for
     "What's your chow?" prompt.
  5. Busybox shell shall open.
  Source: https://alephsecurity.com/vulns/aleph-2019014
- Stock firmware has beamforming functionality, known as BeamFlex,
  using active multi-segment antennas on both bands - controlled by
  RF analog switches, driven by a pair of 74LV164 shift registers.
  Shift registers used for each radio are connected to GPIO14 (clock)
  and GPIO15 of the respective chip.
  They are mapped as generic GPIOs in OpenWrt - in stock firmware,
  they were most likely handled directly by radio firmware,
  given the real-time nature of their control.
  Lack of this support in OpenWrt causes the antennas to behave as
  ordinary omnidirectional antennas, and does not affect throughput in
  normal conditions, but GPIOs are available to tinker with nonetheless.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-09-11 01:36:25 +02:00
John Thomson
62b72eafe4 ath79: mikrotik: use OpenWrt loader for initram image
Return to using the OpenWrt kernel loader to decompress and load kernel
initram image.

Continue to use the vmlinuz kernel for squashfs.

Mikrotik's bootloader RouterBOOT on some ath79 devices is
failing to boot the current initram, due to the size of the initram image.

On the ath79 wAP-ac:
a 5.7MiB initram image would fail to boot
After this change:
a 6.6MiB initram image successfully loads

This partially reverts commit e91344776b.

An alternative of using RouterBOOT's capability of loading an initrd ELF
section was investigated, but the OpenWrt kernel loader allows larger image.

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2022-09-11 01:30:11 +02:00
Aleksander Jan Bajkowski
9423fc424c lantiq: xrx200: backport upstream network fixes
This series contains bug fixes that may occur under
memory pressure.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-09-11 01:30:11 +02:00
Josef Schlehofer
ef223e58a3 mvebu: PCI: aardvark: Implement workaround for PCIe Completion Timeout
Turris MOX randomly crashes up, when there is connected miniPCIe card
MediaTek MT7915 with the following output:

[   71.457007] Internal error: synchronous external abort: 96000210 [#1] SMP
[   71.464021] Modules linked in: xt_connlimit pppoe ppp_async nf_conncount iptable_nat ath9k xt_state xt_nat xt_helper xt_conntrack xt_connmark xt_connbytes xt_REDIREl
[   71.464187]  btintel br_netfilter bnep bluetooth ath9k_hw ath10k_pci ath10k_core ath sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_tcindex cls_route cls_mg
[   71.629589] CPU: 0 PID: 1298 Comm: kworker/u5:3 Not tainted 5.4.114 #0
[   71.636319] Hardware name: CZ.NIC Turris Mox Board (DT)
[   71.641725] Workqueue: napi_workq napi_workfn
[   71.646221] pstate: 80400085 (Nzcv daIf +PAN -UAO)
[   71.651169] pc : mt76_set_irq_mask+0x118/0x150 [mt76]
[   71.656385] lr : mt7915_init_debugfs+0x358/0x368 [mt7915e]
[   71.662038] sp : ffffffc010003cd0
[   71.665451] x29: ffffffc010003cd0 x28: 0000000000000060
[   71.670929] x27: ffffffc010a56f98 x26: ffffffc010c0fa9a
[   71.676407] x25: ffffffc010ba8788 x24: ffffff803e01fe00
[   71.681885] x23: 0000000000000030 x22: ffffffc010003dc4
[   71.687361] x21: 0000000000000000 x20: ffffff803e01fea4
[   71.692839] x19: ffffff803cb725c0 x18: 000000002d660780
[   71.698317] x17: 0000000000000000 x16: 0000000000000001
[   71.703795] x15: 0000000000005ee0 x14: ffffffc010d1d000
[   71.709272] x13: 0000000000002f70 x12: 0000000000000000
[   71.714749] x11: 0000000000000000 x10: 0000000000000040
[   71.720226] x9 : ffffffc010bbe980 x8 : ffffffc010bbe978
[   71.725704] x7 : ffffff803e4003f0 x6 : 0000000000000000
[   71.731181] x5 : ffffffc02f240000 x4 : ffffffc010003e00
[   71.736658] x3 : 0000000000000000 x2 : ffffffc008e3f230
[   71.742135] x1 : 00000000000d7010 x0 : ffffffc0114d7010
[   71.747613] Call trace:
[   71.750137]  mt76_set_irq_mask+0x118/0x150 [mt76]
[   71.754990]  mt7915_dual_hif_set_irq_mask+0x108/0xdc0 [mt7915e]
[   71.761098]  __handle_irq_event_percpu+0x6c/0x170
[   71.765950]  handle_irq_event_percpu+0x34/0x88
[   71.770531]  handle_irq_event+0x40/0xb0
[   71.774486]  handle_level_irq+0xe0/0x170
[   71.778530]  generic_handle_irq+0x24/0x38
[   71.782667]  advk_pcie_irq_handler+0x11c/0x238
[   71.787249]  __handle_irq_event_percpu+0x6c/0x170
[   71.792099]  handle_irq_event_percpu+0x34/0x88
[   71.796680]  handle_irq_event+0x40/0xb0
[   71.800633]  handle_fasteoi_irq+0xdc/0x190
[   71.804855]  generic_handle_irq+0x24/0x38
[   71.808988]  __handle_domain_irq+0x60/0xb8
[   71.813213]  gic_handle_irq+0x8c/0x198
[   71.817077]  el1_irq+0xf0/0x1c0
[   71.820314]  el1_da+0xc/0xc0
[   71.823288]  mt76_set_irq_mask+0x118/0x150 [mt76]
[   71.828141]  mt7915_mac_tx_free+0x4c4/0x828 [mt7915e]
[   71.833352]  mt7915_queue_rx_skb+0x5c/0xa8 [mt7915e]
[   71.838473]  mt76_dma_cleanup+0x89c/0x1248 [mt76]
[   71.843329]  __napi_poll+0x38/0xf8
[   71.846835]  napi_workfn+0x58/0xb0
[   71.850342]  process_one_work+0x1fc/0x390
[   71.854475]  worker_thread+0x48/0x4d0
[   71.858252]  kthread+0x120/0x128
[   71.861581]  ret_from_fork+0x10/0x1c
[   71.865273] Code: 52800000 d65f03c0 f9562c00 8b214000 (b9400000)
[   71.871560] ---[ end trace 1d4e29987011411b ]---
[   71.876320] Kernel panic - not syncing: Fatal exception in interrupt
[   71.882875] SMP: stopping secondary CPUs
[   71.886923] Kernel Offset: disabled
[   71.890519] CPU features: 0x0002,00002008
[   71.894649] Memory Limit: none
[   71.897799] Rebooting in 3 seconds..

Patch is awaiting upstream merge:
https://lore.kernel.org/linux-pci/20220802123816.21817-1-pali@kernel.org/T/#u

There was also discussion about it in the linux-pci mailing list, where can
be found response from Marvell's employee regarding A3720 PCIe erratum 3.12, which seems to provide further details which help this issue:
https://lore.kernel.org/linux-pci/BN9PR18MB425154FE5019DCAF2028A1D5DB8D9@BN9PR18MB4251.namprd18.prod.outlook.com/t/#u

Reported-by: Ondřej Caletka <ondrej@caletka.cz> [Turris MOX]
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2022-09-11 01:30:11 +02:00
Martin Kennedy
9efbcdfdee mpc85xx: Make AP3825i boot env partition writable
End-users may need to be able to rewrite u-boot configuration on the
WS-AP3825i, which has had repeated issues with the exact configuration
of u-boot, e.g. commit 1d06277407 ("mpc85xx: Fix output location of
padded dtb") (alongside other failures documented for example in this
post[^1] from the main AP3825i porting thread).

To assist with this, remove the `read-only` property from the u-boot
configuration partitions cfg1 and cfg2.

[^1]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/107

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
2022-09-11 01:30:11 +02:00
Josef Schlehofer
2f496c34b6 mpc85xx: add patch to fix gpio mpc8xxx
Backports patch, which is currently on review [1] for kernel 5.10 and
kernel 5.15, where it applies cleanly. This was tested on CZ.NIC Turris
1.1 router running OpenWrt 21.02.03 with kernel 5.15.

Before:

- In /var/log/messages:
```
[   16.392988] lm90 0-004c: cannot request IRQ 48
[   16.398280] lm90: probe of 0-004c failed with error -22
```

- Sensors does not work:
```
root@turris:~# sensors
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
```

After:

```
root@turris:/# sensors
sa56004-i2c-0-4c
Adapter: MPC adapter (i2c@3000)
temp1:        +44.0°C  (low  =  +0.0°C, high = +70.0°C)
                       (crit = +85.0°C, hyst = +75.0°C)
temp2:        +73.8°C  (low  =  +0.0°C, high = +70.0°C)  ALARM (HIGH)
                       (crit = +85.0°C, hyst = +75.0°C)
```

[1] https://lore.kernel.org/linux-gpio/20220906105431.30911-1-pali@kernel.org/

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-09-11 01:30:11 +02:00
Rosen Penev
f4eef5f2a1 ramips: add support for Linksys E7350
Linksys E7350 is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specifications:
- SoC: MT7621 (880MHz, 2 Cores)
- RAM: 256 MB
- Flash: 128 MB NAND
- Wi-Fi:
  - MT7915D: 2.4/5 GHz (DBDC)
- Ethernet: 5x 1GiE MT7530
- USB: 1x USB 3.0
- UART: J4 (57600 baud)
  - Pinout: [3V3] (TXD) (RXD) (blank) (GND)

Notes:
* This device has a dual-boot partition scheme, but this firmware works
  only on boot partition 1.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-09-11 01:30:11 +02:00
Rosen Penev
26a6a6a60b ramips: add support for Belkin RT1800
Belkin RT1800 is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specifications:
- SoC: MT7621 (880MHz, 2 Cores)
- RAM: 256 MB
- Flash: 128 MB NAND
- Wi-Fi:
  - MT7915D: 2.4/5 GHz (DBDC)
- Ethernet: 5x 1GiE MT7530
- USB: 1x USB 3.0
- UART: J4 (57600 baud)
  - Pinout: [3V3] (TXD) (RXD) (blank) (GND)

Notes:
* This device has a dual-boot partition scheme, but this firmware works
  only on boot partition 1.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-09-11 01:30:11 +02:00
Ray Wang
fe609889e2 ramips: add RT-N600 alternative name to RT-AC1200
RT-N600 is internally the same as RT-AC1200, as veryfied by @russinnes .
Adding alt_name so that people can find it in firmware selector.

Signed-off-by: Ray Wang <raywang777@foxmail.com>
Tested-by: Russ Innes <russ.innes@gmail.com>
2022-09-11 01:30:11 +02:00
Andrey Butirsky
5806914794 ramips: add support for Kroks Rt-Cse SIM Injector DS
Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958:
https://kroks.ru/search/?text=1958
See Kroks OpenWrt fork for support of other models:
https://github.com/kroks-free/openwrt

Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 5x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- USB: 1x
- SIM-reader: 2x (driven by a dedicated chip with it's own firmware)
- Buttons: reset
- LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.)

Flashing:
- sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254
- U-Boot launches a WEB server if Reset button is held during power up,
  IP: 192.168.1.1

MAC addresses as verified by OEM firmware:
vendor   OpenWrt   source
LAN      eth0      factory 0x4 (label)
2g       wlan0     label

Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-09-11 01:30:11 +02:00
Andrey Butirsky
0a79c77a4e ramips: add support for Kroks Rt-Pot mXw DS RSIM router
Aka "Kroks KNdRt31R19".
Ported from v19.07.8 of OpenWrt fork:
see https://github.com/kroks-free/openwrt
for support of other models.

Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- mPCIe: 1x (usually equipped with an LTE modem by vendor)
- Buttons: reset
- LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status

Flashing:
- sysupgrade image via stock firmware WEB interface.
- U-Boot launches a WEB server if Reset button is held during power up.
Server IP: 192.168.1.1

SIM card switching:
The device supports up to 4 SIM cards - 2 locally on board and 2 on
remote SIM-injector.
By default, 1-st local SIM is active.
To switch to e.g. 1-st remote SIM:
echo 0 > /sys/class/gpio/modem1power/value
echo 0 > /sys/class/gpio/modem1sim1/value
echo 1 > /sys/class/gpio/modem1rsim1/value
echo 1 > /sys/class/gpio/modem1power/value

MAC addresses as verified by OEM firmware:
vendor   OpenWrt   source
LAN      eth0      factory 0x4 (label)
2g       wlan0     label

Signed-off-by: Kroks <dev@kroks.ru>
[butirsky@gmail.com: port to master; drop dts-v1]
Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-09-11 01:30:11 +02:00
John Audia
837fd23c80 kernel: bump 5.10 to 5.10.142
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-11 01:30:11 +02:00
John Audia
e8a62a1e60 kernel: bump 5.10 to 5.10.141
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-11 01:30:11 +02:00
Daniel Golle
675cf75578 ramips: add config-5.15 for mt7620 subtarget
Add Kernel config for testing Linux 5.15 for the mt7620 subtarget.
Tested on Youku YK-L1 which boots fine.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-10 22:52:20 +01:00
Andreas Böhler
5f8c86e654 realtek: add support for TP-Link SG2452P v4 aka T1600G-52PS v4
This is an RTL8393-based switch with 802.3af on all 48 ports.

Specifications:
---------------
 * SoC:       Realtek RTL8393M
 * Flash:     32 MiB SPI flash
 * RAM:       256 MiB
 * Ethernet:  48x 10/100/1000 Mbps with PoE+
 * Buttons:   1x "Reset" button, 1x "Speed" button
 * UART:      1x serial header, unpopulated
 * PoE:       12x TI TPS23861 I2C PoE controller, 384W PoE budget
 * SFP:       4 SFP ports

Works:
------
  - (48) RJ-45 ethernet ports
  - Switch functions
  - Buttons
  - All LEDs on front panel except port LEDs
  - Fan monitoring and basic control

Not yet enabled:
----------------
  - PoE - ICs are not in AUTO mode, so the kernel driver is not usable
  - Port LEDs
  - SFP cages

Install via web interface:
-------------------------

Not supported at this time.

Install via serial console/tftp:
--------------------------------

The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.

Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. To install OpenWRT:

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"

Power on device, and stop boot by pressing any key.
Once the shell is active:
 1. Ground out the CLK (pin 16) of the ROM (U6)
 2. Select option "3. Start"
 3. Bootloader notes that "The kernel has been damaged!"
 4. Release CLK as soon as bootloader thinks image is corrupted.
 5. Bootloader enters automatic recovery -- details printed on console
 6. Watch as the bootloader flashes and boots OpenWRT.

Blind install via tftp:
-----------------------

This method works when it's not feasible to install a serial header.

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"
 3. Watch network traffic (tcpdump or wireshark works)
 4. Power on the device.
 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6)
 6. When 192.168.0.30 makes tftp requests, release pin 16
 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-09-10 22:13:52 +02:00
Martin Kennedy
eb425f9ec9 x86: setup netdev paths for MX100
The Meraki MX100 has ten 1000BASE-T and 2 SFP ethernet ports through
3, 4-port PCIe devices. The default enumeration of these network
devices' names does not correspond to their labeling. Fix this by
explicitly naming the devices, mapping against their sysfs path.

Note that these default network names can only be up to 8 characters,
because we can have up to 8 characters of modifiers (e.g. ^br-,
.4096$), and because the maximum network interface name is 16
characters long.

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[lowercase subject]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-09-10 21:16:39 +02:00
Daniel Golle
f7dbdcfa54 mediatek: filogic: use WPS button instead of RST on BPi-R3
The GPIO used for the RST button is also used for PCIe-CLKREQ signal.
Hence it cannot be used as button signal if PCIe is also used.
Wire up WPS button to serve as KEY_RESTART in Linux and "reset" button
in U-Boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-10 19:20:26 +01:00
Rosen Penev
22b7bd6b13
Makefile: replace head call with grep's -m
head is not necessary here.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-09-10 15:42:36 +02:00
Daniel Golle
a34cd4f66a mediatek: bananapi-r3: remove kmod-btmtkuart from default packages
The package kmod-btmtkuart is specific for MT7622 and isn't available
for MT7986 (which doesn't have this built-in Bluetooth like MT7622).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-10 03:23:20 +01:00
Daniel Golle
ff55e54fa3 kernel: fix build on bcm27xx target platform
The bump to Linux 5.15.67 brought some changes in the VC4 display
driver which we had also patched downstream. Fix our local patches to
fix the build.

Fixes: fbe2f7db86 ("kernel: bump 5.15 to 5.15.67")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-10 01:26:53 +01:00
David Bauer
1588069612 rockchip: add system-LED aliases specific to OpenWrt
Add the aliases sections required to detect LEDs specific to OpenWrt
boot / update indication for the NanoPi R4S.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-10 01:55:54 +02:00
David Bauer
b5675f500d rockchip: ensure NanoPi R4S has unique MAC address
Ensure the MAC address for all NanoPi R4S boards is assigned unique for
each board.

FriendlyElec ship two versions of the R4S: The standard as well as the
enterprise edition with only the enterprise edition including the EEPROM
chip that stores the unique MAC address.

In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S in case the EEPROM chip is not
present by generating the board MAC from the SD card CID.

[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R4S#Differences_Between_R4S_Standard_Version_.26_R4S_Enterprise_Version

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-10 01:54:40 +02:00
Bjørn Mork
2ca5602864 realtek: fix RTL839x receive tag decoding
The previous fixup was incomplete, and the offsets for the
queue and crc_error cpu_tag bitfields were still wrong on
RTL839x.

Fixes: 545c6113c9 ("realtek: fix RTL838x receive tag decoding")
Suggested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2022-09-09 22:11:55 +02:00
Daniel Golle
f755c41038 kernel: backport MediaTek USB Bluetooth additions
Backport commits from linux.git adding support for various MT7921
Bluetooth USB IDs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-09 21:08:37 +01:00
Daniel Golle
f97fbd8a9a mediatek: rename some patches
To ease maintainance rename patches to contain the kernel version they
have first been part of.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-09 21:08:37 +01:00
Chukun Pan
c91dd139d6 mediatek: 5.15: add missing patch suffix
The 213 patch is missing filename suffix. Fix it.

Fixes: dabcaac ("mediatek: add mt7986 soc support to the target")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-09-09 21:08:37 +01:00
Chukun Pan
a9233175e8 mediatek: mt7986a/b-rfb: fix 02_network setup
According to the device tree, the lan ports are
lan0 to lan3, and the wan port is eth1.

Fixes: cffc77a ("mediatek: add filogic subtarget")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-09-09 21:08:37 +01:00
John Audia
fbe2f7db86 kernel: bump 5.15 to 5.15.67
All patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-09 21:08:37 +01:00
John Audia
c0f74a01b5 kernel: add # CONFIG_ARM64_ERRATUM_2441009 symbol
No current targets are ARMv9 or Cortex-A510 so comment the new symbol.[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.65&id2=v5.15.64

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-09 21:08:37 +01:00