mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 22:47:56 +00:00
ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access point distributed as Experia WiFi by KPN in the Netherlands. It features two ethernet ports and 2 internal antennas. Specifications -------------- SOC : Mediatek MT7621AT ETH : Two 1 gigabit ports, built into the SOC WIFI : MT7615DN BUTTON: Reset BUTTON: WPS LED : Power (green+red) LED : WiFi (green+blue) LED : WPS (green+red) LED : Followme (green+red) Power : 12 VDC, 1A barrel plug Winbond variant: RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM Flash : Winbond W25Q256JVFQ, 256Mb SPI U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 Macronix variant: RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM Flash : MX25l25635FMI-10G, 256Mb SPI U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 Serial ------ The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin header. The pinout is: VCC (the square), RX, TX, GND. Installation ------------ See the Wiki page [1] for more details, it comes down to: 1. Open the device, take off the heat sink 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also connect the RESET pin for stability (thanks @FPSUsername for reporting) 3. Make a backup in case you want to revert to stock later 4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash 5. Ensure the bootpartition variable is set to 0 in the U-Boot environment located at 0x30000 Note that the U-Boot is password protected, this can optionally be removed. See the forum [2] for more details. MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 00:00:00:11:00:00 | | Ethernet | + 3 | 00:00:00:11:00:03 | | 2g | + 0x020000f00001 | 02:00:00:01:00:01 | | 5g | + 1 | 00:00:00:11:00:01 | +----------+------------------+-------------------+ The label address is stored in ASCII in the board_data partition Notes ----- - This device has a dual-boot partition scheme, but OpenWRT will claim both partitions for more storage space. Known issues ------------ - 2g MAC address does not match stock due to missing support for that in macaddr_add - Only the power LED is configured by default References ---------- [1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99 [2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653 Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
This commit is contained in:
Harm Berntsen
Hauke Mehrtens
parent
1e0604e0d1
commit
09f313bfd7
@ -21,6 +21,9 @@ engenius,esr600h|\
|
||||
sitecom,wlr-4100-v1-002)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x1000"
|
||||
;;
|
||||
arcadyan,we420223-99)
|
||||
ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x1000" "0x1000"
|
||||
;;
|
||||
allnet,all0256n-4m|\
|
||||
allnet,all0256n-8m|\
|
||||
allnet,all5002|\
|
||||
|
||||
219
target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts
Normal file
219
target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts
Normal file
@ -0,0 +1,219 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "Arcadyan WE420223-99";
|
||||
compatible = "arcadyan,we420223-99", "mediatek,mt7621-soc";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_wps_green;
|
||||
led-wifi = &led_wifi_green;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,57600 ubi.mtd=5 root=/dev/ubiblock0_0";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_green: power_green {
|
||||
label = "green:power";
|
||||
gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
led_power_red: power_red {
|
||||
label = "red:power";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_FAULT;
|
||||
};
|
||||
|
||||
led_wifi_blue: wifi_blue {
|
||||
label = "blue:wifi";
|
||||
gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
};
|
||||
|
||||
led_wifi_green: wifi_green {
|
||||
label = "green:wifi";
|
||||
gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
};
|
||||
|
||||
led_wps_red: wps_red {
|
||||
label = "red:wps";
|
||||
gpios = <&gpio 45 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WPS;
|
||||
};
|
||||
|
||||
led_wps_green: wps_green {
|
||||
label = "green:wps";
|
||||
gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WPS;
|
||||
};
|
||||
|
||||
led_followme_r: followme_red {
|
||||
label = "red:followme";
|
||||
gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
};
|
||||
|
||||
led_followme_g: followme_green {
|
||||
label = "green:followme";
|
||||
gpios = <&gpio 48 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
|
||||
reg = <0>;
|
||||
spi-max-frequency = <70000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "ALL";
|
||||
reg = <0x0 0x2000000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1 {
|
||||
label = "Bootloader";
|
||||
reg = <0x0 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "Config";
|
||||
reg = <0x30000 0x10000>;
|
||||
};
|
||||
|
||||
factory: partition@40000 {
|
||||
label = "Factory";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "kernel";
|
||||
reg = <0x50000 0x1f60000>;
|
||||
};
|
||||
|
||||
partition@490000 {
|
||||
label = "rootfs";
|
||||
reg = <0x490000 0x1b20000>;
|
||||
};
|
||||
|
||||
partition@1000000 {
|
||||
label = "Kernel2";
|
||||
reg = <0x1000000 0xfb0000>;
|
||||
};
|
||||
|
||||
partition@1440000 {
|
||||
label = "RootFS2";
|
||||
reg = <0x1440000 0xb70000>;
|
||||
};
|
||||
|
||||
partition@1fb0000 {
|
||||
label = "glbcfg";
|
||||
reg = <0x1fb0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1fc0000 {
|
||||
label = "board_data";
|
||||
reg = <0x1fc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1fd0000 {
|
||||
label = "glbcfg2";
|
||||
reg = <0x1fd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1fe0000 {
|
||||
label = "board_data2";
|
||||
reg = <0x1fe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@1 {
|
||||
status = "okay";
|
||||
label = "swp1";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "okay";
|
||||
label = "swp0";
|
||||
phy-handle = <ðphy0>;
|
||||
};
|
||||
|
||||
&mdio {
|
||||
ethphy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
mt76@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&factory 0x0000>;
|
||||
};
|
||||
};
|
||||
@ -187,6 +187,31 @@ define Device/ampedwireless_ally-00x19k
|
||||
endef
|
||||
TARGET_DEVICES += ampedwireless_ally-00x19k
|
||||
|
||||
define Device/arcadyan_we420223-99
|
||||
$(Device/dsa-migration)
|
||||
$(Device/uimage-lzma-loader)
|
||||
DEVICE_VENDOR := Arcadyan
|
||||
DEVICE_MODEL := WE420223-99
|
||||
DEVICE_ALT0_VENDOR := KPN
|
||||
DEVICE_ALT0_MODEL := Experia WiFi
|
||||
IMAGE_SIZE := 32128k
|
||||
KERNEL_SIZE := 4352k
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 64k
|
||||
PAGESIZE := 1
|
||||
SUBPAGESIZE := 1
|
||||
VID_HDR_OFFSET := 64
|
||||
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
||||
uImage none | arcadyan-trx 0x746f435d
|
||||
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
||||
uImage none
|
||||
IMAGES += factory.trx
|
||||
IMAGE/factory.trx := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | check-size
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
DEVICE_PACKAGES := kmod-mt7615-firmware
|
||||
endef
|
||||
TARGET_DEVICES += arcadyan_we420223-99
|
||||
|
||||
define Device/asiarf_ap7621-001
|
||||
$(Device/dsa-migration)
|
||||
IMAGE_SIZE := 16000k
|
||||
|
||||
@ -8,6 +8,9 @@ ramips_setup_interfaces()
|
||||
local board="$1"
|
||||
|
||||
case $board in
|
||||
arcadyan,we420223-99)
|
||||
ucidef_set_interface_lan "swp0 swp1"
|
||||
;;
|
||||
ampedwireless,ally-00x19k|\
|
||||
asus,rp-ac56|\
|
||||
asus,rp-ac87|\
|
||||
@ -150,6 +153,11 @@ ramips_setup_macs()
|
||||
wan_mac=$(mtd_get_mac_ascii hwconfig HW.WAN.MAC.Address)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
arcadyan,we420223-99)
|
||||
label_mac=$(mtd_get_mac_ascii board_data mac)
|
||||
lan_mac=$label_mac
|
||||
ucidef_set_network_device_mac eth0 $(macaddr_add "$label_mac" 3)
|
||||
;;
|
||||
asus,rt-ac65p|\
|
||||
asus,rt-ac85p)
|
||||
wan_mac=$(mtd_get_mac_ascii u-boot-env et1macaddr)
|
||||
|
||||
@ -10,6 +10,15 @@ PHYNBR=${DEVPATH##*/phy}
|
||||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
arcadyan,we420223-99)
|
||||
if [ "$PHYNBR" = "0" ]; then
|
||||
mac24=$(macaddr_add "$(get_mac_label)" "0xf00001")
|
||||
echo -n "$mac24" > /sys${DEVPATH}/macaddress
|
||||
elif [ "$PHYNBR" = "1" ]; then
|
||||
mac5=$(macaddr_add "$(get_mac_label)" 1)
|
||||
echo -n "$mac5" > /sys${DEVPATH}/macaddress
|
||||
fi
|
||||
;;
|
||||
beeline,smartbox-flash)
|
||||
hw_mac_addr=$(macaddr_add $(mtd_get_mac_encrypted_arcadyan "board_data") 1)
|
||||
[ "$PHYNBR" = "0" ] && echo -n "$hw_mac_addr" > /sys${DEVPATH}/macaddress
|
||||
|
||||
@ -52,6 +52,7 @@ platform_do_upgrade() {
|
||||
case "$board" in
|
||||
ampedwireless,ally-00x19k|\
|
||||
ampedwireless,ally-r1900k|\
|
||||
arcadyan,we420223-99|\
|
||||
asus,rt-ac65p|\
|
||||
asus,rt-ac85p|\
|
||||
asus,rt-ax53u|\
|
||||
|
||||
Loading…
Reference in New Issue
Block a user