mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
09f313bfd7
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access point distributed as Experia WiFi by KPN in the Netherlands. It features two ethernet ports and 2 internal antennas. Specifications -------------- SOC : Mediatek MT7621AT ETH : Two 1 gigabit ports, built into the SOC WIFI : MT7615DN BUTTON: Reset BUTTON: WPS LED : Power (green+red) LED : WiFi (green+blue) LED : WPS (green+red) LED : Followme (green+red) Power : 12 VDC, 1A barrel plug Winbond variant: RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM Flash : Winbond W25Q256JVFQ, 256Mb SPI U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 Macronix variant: RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM Flash : MX25l25635FMI-10G, 256Mb SPI U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 Serial ------ The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin header. The pinout is: VCC (the square), RX, TX, GND. Installation ------------ See the Wiki page [1] for more details, it comes down to: 1. Open the device, take off the heat sink 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also connect the RESET pin for stability (thanks @FPSUsername for reporting) 3. Make a backup in case you want to revert to stock later 4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash 5. Ensure the bootpartition variable is set to 0 in the U-Boot environment located at 0x30000 Note that the U-Boot is password protected, this can optionally be removed. See the forum [2] for more details. MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 00:00:00:11:00:00 | | Ethernet | + 3 | 00:00:00:11:00:03 | | 2g | + 0x020000f00001 | 02:00:00:01:00:01 | | 5g | + 1 | 00:00:00:11:00:01 | +----------+------------------+-------------------+ The label address is stored in ASCII in the board_data partition Notes ----- - This device has a dual-boot partition scheme, but OpenWRT will claim both partitions for more storage space. Known issues ------------ - 2g MAC address does not match stock due to missing support for that in macaddr_add - Only the power LED is configured by default References ---------- [1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99 [2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653 Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
2744 lines
77 KiB
Makefile
2744 lines
77 KiB
Makefile
#
|
|
# MT7621 Profiles
|
|
#
|
|
|
|
include ./common-sercomm.mk
|
|
include ./common-tp-link.mk
|
|
|
|
DEFAULT_SOC := mt7621
|
|
|
|
DEVICE_VARS += ELECOM_HWNAME LINKSYS_HWNAME
|
|
|
|
ifdef CONFIG_LINUX_5_10
|
|
DTS_CPPFLAGS += -DDTS_LEGACY
|
|
endif
|
|
|
|
define Build/arcadyan-trx
|
|
echo -ne "hsqs" > $@.hsqs
|
|
$(eval trx_magic=$(word 1,$(1)))
|
|
$(STAGING_DIR_HOST)/bin/otrx create $@.trx -M $(trx_magic) -f $@ \
|
|
-a 0x20000 -b 0x420000 -f $@.hsqs -a 1000
|
|
mv $@.trx $@
|
|
dd if=/dev/zero bs=1024 count=1 >> $@.tail
|
|
echo -ne "HDR0" | dd of=$@.tail bs=1 seek=$$((0x10c)) count=4 \
|
|
conv=notrunc 2>/dev/null
|
|
dd if=$@.tail >> $@ 2>/dev/null
|
|
rm $@.hsqs $@.tail
|
|
endef
|
|
|
|
define Build/gemtek-trailer
|
|
printf "%s%08X" ".GEMTEK." "$$(cksum $@ | cut -d ' ' -f1)" >> $@
|
|
endef
|
|
|
|
define Build/h3c-blank-header
|
|
dd if=/dev/zero of=$@.blank bs=160 count=1
|
|
cat $@ >> $@.blank
|
|
mv $@.blank $@
|
|
endef
|
|
|
|
define Build/haier-sim_wr1800k-factory
|
|
mkdir -p "$@.tmp"
|
|
mv "$@" "$@.tmp/UploadBrush-bin.img"
|
|
$(MKHASH) md5 "$@.tmp/UploadBrush-bin.img" | head -c32 > "$@.tmp/check_MD5.txt"
|
|
$(TAR) -czf "$@.tmp.tgz" -C "$@.tmp" UploadBrush-bin.img check_MD5.txt
|
|
$(STAGING_DIR_HOST)/bin/openssl aes-256-cbc -e -salt -in "$@.tmp.tgz" -out "$@" -k QiLunSmartWL
|
|
printf %32s $(DEVICE_MODEL) >> "$@"
|
|
rm -rf "$@.tmp" "$@.tmp.tgz"
|
|
endef
|
|
|
|
define Build/iodata-mstc-header
|
|
( \
|
|
data_size_crc="$$(dd if=$@ ibs=64 skip=1 2>/dev/null | gzip -c | \
|
|
tail -c 8 | od -An -tx8 --endian little | tr -d ' \n')"; \
|
|
echo -ne "$$(echo $$data_size_crc | sed 's/../\\x&/g')" | \
|
|
dd of=$@ bs=8 count=1 seek=7 conv=notrunc 2>/dev/null; \
|
|
)
|
|
dd if=/dev/zero of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null
|
|
( \
|
|
header_crc="$$(dd if=$@ bs=64 count=1 2>/dev/null | gzip -c | \
|
|
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
|
|
echo -ne "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
|
|
dd of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null; \
|
|
)
|
|
endef
|
|
|
|
define Build/belkin-header
|
|
$(eval magic=$(word 1,$(1)))
|
|
$(eval hw_ver=$(word 2,$(1)))
|
|
$(eval fw_ver=$(word 3,$(1)))
|
|
|
|
( \
|
|
type_fw_date=$$(printf "01%02x%02x%02x" \
|
|
$$(date -d "@$(SOURCE_DATE_EPOCH)" "+%y %m %d")); \
|
|
hw_fw_ver=$$(printf "%02x%02x%02x%02x" \
|
|
$(hw_ver) $$(echo $(fw_ver) | cut -d. -f-3 | tr . ' ')); \
|
|
fw_len_crc=$$(gzip -c $@ | tail -c 8 | od -An -tx8 | tr -d ' \n'); \
|
|
fw_crc_len="$${fw_len_crc:8:8}$${fw_len_crc:0:8}"; \
|
|
\
|
|
printf "$(magic)" | dd bs=4 count=1 conv=sync 2>/dev/null; \
|
|
printf "$$(echo $${type_fw_date}$${hw_fw_ver} | \
|
|
sed 's/../\\x&/g')"; \
|
|
printf "$$(echo $${fw_crc_len}$${fw_crc_len} | \
|
|
sed 's/../\\x&/g')"; \
|
|
printf "\x5c\x78\x00\x00"; \
|
|
cat $@; \
|
|
) > $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/ubnt-erx-factory-image
|
|
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
|
|
echo '21001:7' > $(1).compat; \
|
|
$(TAR) -cf $(1) --transform='s/^.*/compat/' $(1).compat; \
|
|
\
|
|
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp/' $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE); \
|
|
$(MKHASH) md5 $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) > $(1).md5; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp.md5/' $(1).md5; \
|
|
\
|
|
echo "dummy" > $(1).rootfs; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp/' $(1).rootfs; \
|
|
\
|
|
$(MKHASH) md5 $(1).rootfs > $(1).md5; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp.md5/' $(1).md5; \
|
|
\
|
|
echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $(1).version; \
|
|
$(TAR) -rf $(1) --transform='s/^.*/version.tmp/' $(1).version; \
|
|
\
|
|
$(CP) $(1) $(BIN_DIR)/; \
|
|
else \
|
|
echo "WARNING: initramfs kernel image too big, cannot generate factory image (actual $$(stat -c%s $@); max $(KERNEL_SIZE))" >&2; \
|
|
fi
|
|
endef
|
|
|
|
define Build/zytrx-header
|
|
$(eval board=$(word 1,$(1)))
|
|
$(eval version=$(word 2,$(1)))
|
|
$(STAGING_DIR_HOST)/bin/zytrx -B '$(board)' -v '$(version)' -i $@ -o $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/zyxel-nwa-fit
|
|
$(TOPDIR)/scripts/mkits-zyxel-fit.sh \
|
|
$@.its $@ "6b e1 6f e1 ff ff ff ff ff ff"
|
|
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Device/dsa-migration
|
|
DEVICE_COMPAT_VERSION := 1.1
|
|
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
|
|
endef
|
|
|
|
define Device/adslr_g7
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ADSLR
|
|
DEVICE_MODEL := G7
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += adslr_g7
|
|
|
|
define Device/afoundry_ew1200
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := AFOUNDRY
|
|
DEVICE_MODEL := EW1200
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-mt7603 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += ew1200
|
|
endef
|
|
TARGET_DEVICES += afoundry_ew1200
|
|
|
|
define Device/alfa-network_quad-e4g
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := Quad-E4G
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 uboot-envtools \
|
|
-wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += quad-e4g
|
|
endef
|
|
TARGET_DEVICES += alfa-network_quad-e4g
|
|
|
|
define Device/ampedwireless_ally_common
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Amped Wireless
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware uboot-envtools
|
|
IMAGE_SIZE := 32768k
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'flashable-initramfs' |\
|
|
edimax-header -s CSYS -m RN68 -f 0x001c0000 -S 0x01100000
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/ampedwireless_ally-r1900k
|
|
$(Device/ampedwireless_ally_common)
|
|
DEVICE_MODEL := ALLY-R1900K
|
|
DEVICE_PACKAGES += kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += ampedwireless_ally-r1900k
|
|
|
|
define Device/ampedwireless_ally-00x19k
|
|
$(Device/ampedwireless_ally_common)
|
|
DEVICE_MODEL := ALLY-00X19K
|
|
endef
|
|
TARGET_DEVICES += ampedwireless_ally-00x19k
|
|
|
|
define Device/arcadyan_we420223-99
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Arcadyan
|
|
DEVICE_MODEL := WE420223-99
|
|
DEVICE_ALT0_VENDOR := KPN
|
|
DEVICE_ALT0_MODEL := Experia WiFi
|
|
IMAGE_SIZE := 32128k
|
|
KERNEL_SIZE := 4352k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 64k
|
|
PAGESIZE := 1
|
|
SUBPAGESIZE := 1
|
|
VID_HDR_OFFSET := 64
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none | arcadyan-trx 0x746f435d
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none
|
|
IMAGES += factory.trx
|
|
IMAGE/factory.trx := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += arcadyan_we420223-99
|
|
|
|
define Device/asiarf_ap7621-001
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := AsiaRF
|
|
DEVICE_MODEL := AP7621-001
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += asiarf_ap7621-001
|
|
|
|
define Device/asiarf_ap7621-nv1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := AsiaRF
|
|
DEVICE_MODEL := AP7621-NV1
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += asiarf_ap7621-nv1
|
|
|
|
define Device/asus_rp-ac56
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RP-AC56
|
|
IMAGE_SIZE := 16000k
|
|
BLOCKSIZE := 64k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 \
|
|
kmod-i2c-ralink kmod-sound-mt7620
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
endef
|
|
TARGET_DEVICES += asus_rp-ac56
|
|
|
|
define Device/asus_rp-ac87
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RP-AC87
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware rssileds
|
|
endef
|
|
TARGET_DEVICES += asus_rp-ac87
|
|
|
|
define Device/asus_rt-ac57u
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC57U
|
|
DEVICE_ALT0_VENDOR := ASUS
|
|
DEVICE_ALT0_MODEL := RT-AC1200GU
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac57u
|
|
|
|
define Device/asus_rt-ac65p
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC65P
|
|
IMAGE_SIZE := 51200k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615-firmware uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac65p
|
|
|
|
define Device/asus_rt-ac85p
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC85P
|
|
IMAGE_SIZE := 51200k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615-firmware uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac85p
|
|
|
|
define Device/asus_rt-n56u-b1
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-N56U
|
|
DEVICE_VARIANT := B1
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-n56u-b1
|
|
|
|
define Device/asus_rt-ax53u
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AX53U
|
|
DEVICE_ALT0_VENDOR := ASUS
|
|
DEVICE_ALT0_MODEL := RT-AX1800U
|
|
IMAGE_SIZE := 51200k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware kmod-usb3 uboot-envtools \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ax53u
|
|
|
|
define Device/beeline_smartbox-flash
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Beeline
|
|
DEVICE_MODEL := SmartBox Flash
|
|
IMAGE_SIZE := 32768k
|
|
KERNEL_SIZE := 4352k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none | arcadyan-trx 0x746f435d | pad-to $$(KERNEL_SIZE)
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none
|
|
IMAGES += factory.trx
|
|
IMAGE/factory.trx := append-kernel | append-ubi | check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615-firmware \
|
|
uboot-envtools uencrypt
|
|
endef
|
|
TARGET_DEVICES += beeline_smartbox-flash
|
|
|
|
define Device/beeline_smartbox-giga
|
|
$(Device/sercomm_dxx)
|
|
IMAGE_SIZE := 24576k
|
|
SERCOMM_HWID := DBE
|
|
SERCOMM_HWVER := 10100
|
|
SERCOMM_SWVER := 1001
|
|
DEVICE_VENDOR := Beeline
|
|
DEVICE_MODEL := SmartBox GIGA
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
kmod-usb3 uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += beeline_smartbox-giga
|
|
|
|
define Device/beeline_smartbox-turbo
|
|
$(Device/sercomm_dxx)
|
|
IMAGE_SIZE := 32768k
|
|
SERCOMM_HWID := DF3
|
|
SERCOMM_HWVER := 10200
|
|
SERCOMM_SWVER := 1004
|
|
DEVICE_VENDOR := Beeline
|
|
DEVICE_MODEL := SmartBox TURBO
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware \
|
|
kmod-usb3 uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += beeline_smartbox-turbo
|
|
|
|
define Device/belkin_rt1800
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 49152k
|
|
DEVICE_VENDOR := Belkin
|
|
DEVICE_MODEL := RT1800
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware kmod-usb3 uboot-envtools
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
|
append-squashfs4-fakeroot
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | belkin-header RT18 1 9.9.9
|
|
endef
|
|
TARGET_DEVICES += belkin_rt1800
|
|
|
|
define Device/buffalo_wsr-1166dhp
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
|
|
IMAGE_SIZE := 15936k
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WSR-1166DHP
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
SUPPORTED_DEVICES += wsr-1166
|
|
endef
|
|
TARGET_DEVICES += buffalo_wsr-1166dhp
|
|
|
|
define Device/buffalo_wsr-2533dhpl
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7936k
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WSR-2533DHPL
|
|
DEVICE_ALT0_VENDOR := Buffalo
|
|
DEVICE_ALT0_MODEL := WSR-2533DHP
|
|
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += buffalo_wsr-2533dhpl
|
|
|
|
define Device/buffalo_wsr-600dhp
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WSR-600DHP
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-rt2800-pci
|
|
SUPPORTED_DEVICES += wsr-600
|
|
endef
|
|
TARGET_DEVICES += buffalo_wsr-600dhp
|
|
|
|
define Device/bolt_arion
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := BOLT
|
|
DEVICE_MODEL := Arion
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += bolt_arion
|
|
|
|
define Device/cudy_m1800
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := M1800
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := R17
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
endef
|
|
TARGET_DEVICES += cudy_m1800
|
|
|
|
define Device/cudy_wr1300-v1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := WR1300
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += cudy,wr1300 R10
|
|
endef
|
|
TARGET_DEVICES += cudy_wr1300-v1
|
|
|
|
define Device/cudy_wr1300-v2
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := WR1300
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
SUPPORTED_DEVICES += cudy,wr1300 R23
|
|
endef
|
|
TARGET_DEVICES += cudy_wr1300-v2
|
|
|
|
define Device/cudy_wr2100
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := WR2100
|
|
IMAGE_SIZE := 15872k
|
|
UIMAGE_NAME := R11
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += cudy_wr2100
|
|
|
|
define Device/cudy_x6
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32256k
|
|
DEVICE_VENDOR := Cudy
|
|
DEVICE_MODEL := X6
|
|
UIMAGE_NAME := R13
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
endef
|
|
TARGET_DEVICES += cudy_x6
|
|
|
|
define Device/dlink_dap-x1860-a1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 53248k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-X1860
|
|
DEVICE_VARIANT := A1
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 8192k
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size | elx-header 011b0060 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware rssileds
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-x1860-a1
|
|
|
|
define Device/dlink_dir-8xx-a1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
KERNEL := $$(KERNEL) | uimage-sgehdr
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size
|
|
endef
|
|
|
|
define Device/dlink_dir-8xx-r1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
check-size | append-metadata
|
|
endef
|
|
|
|
define Device/dlink_dir-xx60-a1
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 40960k
|
|
UBINIZE_OPTS := -E 5
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
KERNEL := $$(KERNEL) | uimage-sgehdr
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
endef
|
|
|
|
define Device/dlink_dir-1935-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-1935
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES += kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-1935-a1
|
|
|
|
define Device/dlink_dir-1960-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-1960
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-1960-a1
|
|
|
|
define Device/dlink_dir-2640-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-2640
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-2640-a1
|
|
|
|
define Device/dlink_dir-2660-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-2660
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-2660-a1
|
|
|
|
define Device/dlink_dir-3060-a1
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-3060
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-3060-a1
|
|
|
|
define Device/dlink_dir-853-a3
|
|
$(Device/dlink_dir-xx60-a1)
|
|
DEVICE_MODEL := DIR-853
|
|
DEVICE_VARIANT := A3
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-853-a3
|
|
|
|
define Device/dlink_dir-853-r1
|
|
$(Device/dlink_dir-8xx-r1)
|
|
DEVICE_MODEL := DIR-853
|
|
DEVICE_VARIANT := R1
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-853-r1
|
|
|
|
define Device/dlink_dir-860l-b1
|
|
$(Device/dsa-migration)
|
|
$(Device/seama-lzma-loader)
|
|
SEAMA_SIGNATURE := wrgac13_dlink.2013gui_dir860lb
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-860L
|
|
DEVICE_VARIANT := B1
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += dir-860l-b1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-860l-b1
|
|
|
|
define Device/dlink_dir-867-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-867
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-867-a1
|
|
|
|
define Device/dlink_dir-878-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-878
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-878-a1
|
|
|
|
define Device/dlink_dir-878-r1
|
|
$(Device/dlink_dir-8xx-r1)
|
|
DEVICE_MODEL := DIR-878
|
|
DEVICE_VARIANT := R1
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size | \
|
|
sign-dlink-ru 57c5375741c30ca9ebcb36713db4ba51 \
|
|
ab0dff19af8842cdb70a86b4b68d23f7
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-878-r1
|
|
|
|
define Device/dlink_dir-882-a1
|
|
$(Device/dlink_dir-8xx-a1)
|
|
DEVICE_MODEL := DIR-882
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-882-a1
|
|
|
|
define Device/dlink_dir-882-r1
|
|
$(Device/dlink_dir-8xx-r1)
|
|
DEVICE_MODEL := DIR-882
|
|
DEVICE_VARIANT := R1
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size | \
|
|
sign-dlink-ru 57c5375741c30ca9ebcb36713db4ba51 \
|
|
ab0dff19af8842cdb70a86b4b68d23f7
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-882-r1
|
|
|
|
define Device/dual-q_h721
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Dual-Q
|
|
DEVICE_MODEL := H721
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += dual-q_h721
|
|
|
|
define Device/d-team_newifi-d2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := Newifi
|
|
DEVICE_MODEL := D2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += d-team_newifi-d2
|
|
|
|
define Device/d-team_pbr-m1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := PandoraBox
|
|
DEVICE_MODEL := PBR-M1
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += pbr-m1
|
|
endef
|
|
TARGET_DEVICES += d-team_pbr-m1
|
|
|
|
define Device/edimax_ra21s
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Edimax
|
|
DEVICE_MODEL := RA21S
|
|
DEVICE_ALT0_VENDOR := Edimax
|
|
DEVICE_ALT0_MODEL := Gemini RA21S
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 02020040 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += edimax_ra21s
|
|
|
|
define Device/edimax_re23s
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15680k
|
|
DEVICE_VENDOR := Edimax
|
|
DEVICE_MODEL := RE23S
|
|
DEVICE_ALT0_VENDOR := Edimax
|
|
DEVICE_ALT0_MODEL := Gemini RE23S
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
|
|
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | \
|
|
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += edimax_re23s
|
|
|
|
define Device/edimax_rg21s
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Edimax
|
|
DEVICE_MODEL := Gemini AC2600 RG21S
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 02020038 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += edimax_rg21s
|
|
|
|
define Device/elecom_wrc-1167ghbk2-s
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15488k
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-1167GHBK2-S
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elecom-wrc-gs-factory WRC-1167GHBK2-S 0.00
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1167ghbk2-s
|
|
|
|
define Device/elecom_wrc-gs
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := ELECOM
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elecom-wrc-gs-factory $$$$(ELECOM_HWNAME) 0.00 -N | \
|
|
append-string MT7621_ELECOM_$$$$(ELECOM_HWNAME)
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
|
|
define Device/elecom_wrc-1167gs2-b
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1167GS2-B
|
|
ELECOM_HWNAME := WRC-1167GS2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1167gs2-b
|
|
|
|
define Device/elecom_wrc-1167gst2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 24576k
|
|
DEVICE_MODEL := WRC-1167GST2
|
|
ELECOM_HWNAME := WRC-1167GST2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1167gst2
|
|
|
|
define Device/elecom_wrc-1750gs
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1750GS
|
|
ELECOM_HWNAME := WRC-1750GS
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750gs
|
|
|
|
define Device/elecom_wrc-1750gst2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 24576k
|
|
DEVICE_MODEL := WRC-1750GST2
|
|
ELECOM_HWNAME := WRC-1750GST2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750gst2
|
|
|
|
define Device/elecom_wrc-1750gsv
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1750GSV
|
|
ELECOM_HWNAME := WRC-1750GSV
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750gsv
|
|
|
|
define Device/elecom_wrc-1900gst
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-1900GST
|
|
ELECOM_HWNAME := WRC-1900GST
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1900gst
|
|
|
|
define Device/elecom_wrc-2533ghbk2-t
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-2533GHBK2-T
|
|
IMAGE_SIZE := 7808k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 0107003b 8844A2D168B45A2D | \
|
|
elecom-product-header WRC-2533GHBK2-T
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533ghbk2-t
|
|
|
|
define Device/elecom_wrc-2533ghbk-i
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-2533GHBK-I
|
|
IMAGE_SIZE := 9856k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 0107002d 8844A2D168B45A2D | \
|
|
elecom-product-header WRC-2533GHBK-I
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533ghbk-i
|
|
|
|
define Device/elecom_wrc-2533gs2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-2533GS2
|
|
ELECOM_HWNAME := WRC-2533GS2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533gs2
|
|
|
|
define Device/elecom_wrc-2533gst
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 11264k
|
|
DEVICE_MODEL := WRC-2533GST
|
|
ELECOM_HWNAME := WRC-2533GST
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533gst
|
|
|
|
define Device/elecom_wrc-2533gst2
|
|
$(Device/elecom_wrc-gs)
|
|
IMAGE_SIZE := 24576k
|
|
DEVICE_MODEL := WRC-2533GST2
|
|
ELECOM_HWNAME := WRC-2533GST2
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-2533gst2
|
|
|
|
define Device/etisalat_s3
|
|
$(Device/sercomm_dxx)
|
|
IMAGE_SIZE := 32768k
|
|
SERCOMM_HWID := DDK
|
|
SERCOMM_HWVER := 10000
|
|
SERCOMM_SWVER := 4009
|
|
DEVICE_VENDOR := Etisalat
|
|
DEVICE_MODEL := S3
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware \
|
|
kmod-usb3 uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += etisalat_s3
|
|
|
|
define Device/firefly_firewrt
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Firefly
|
|
DEVICE_MODEL := FireWRT
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += firewrt
|
|
endef
|
|
TARGET_DEVICES += firefly_firewrt
|
|
|
|
define Device/gehua_ghl-r-001
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := GeHua
|
|
DEVICE_MODEL := GHL-R-001
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += gehua_ghl-r-001
|
|
|
|
define Device/glinet_gl-mt1300
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-MT1300
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-mt1300
|
|
|
|
define Device/gnubee_gb-pc1
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := GnuBee
|
|
DEVICE_MODEL := Personal Cloud One
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-basic-wolfssl
|
|
IMAGE_SIZE := 32448k
|
|
endef
|
|
TARGET_DEVICES += gnubee_gb-pc1
|
|
|
|
define Device/gnubee_gb-pc2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := GnuBee
|
|
DEVICE_MODEL := Personal Cloud Two
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 -wpad-basic-wolfssl
|
|
IMAGE_SIZE := 32448k
|
|
endef
|
|
TARGET_DEVICES += gnubee_gb-pc2
|
|
|
|
define Device/h3c_tx180x
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 8192k
|
|
IMAGE_SIZE := 120832k
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL_INITRAMFS := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
KERNEL := $$(KERNEL_INITRAMFS) | h3c-blank-header
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := H3C
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware uboot-envtools
|
|
endef
|
|
|
|
define Device/h3c_tx1800-plus
|
|
$(Device/h3c_tx180x)
|
|
DEVICE_MODEL := TX1800 Plus
|
|
endef
|
|
TARGET_DEVICES += h3c_tx1800-plus
|
|
|
|
define Device/h3c_tx1801-plus
|
|
$(Device/h3c_tx180x)
|
|
DEVICE_MODEL := TX1801 Plus
|
|
endef
|
|
TARGET_DEVICES += h3c_tx1801-plus
|
|
|
|
define Device/h3c_tx1806
|
|
$(Device/h3c_tx180x)
|
|
DEVICE_MODEL := TX1806
|
|
endef
|
|
TARGET_DEVICES += h3c_tx1806
|
|
|
|
define Device/haier-sim_wr1800k
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 125440k
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
|
|
ARTIFACTS := initramfs-factory.bin
|
|
ARTIFACT/initramfs-factory.bin := append-image-stage initramfs-kernel.bin | \
|
|
haier-sim_wr1800k-factory
|
|
endif
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware uboot-envtools
|
|
endef
|
|
|
|
define Device/haier_har-20s2u1
|
|
$(Device/haier-sim_wr1800k)
|
|
DEVICE_VENDOR := Haier
|
|
DEVICE_MODEL := HAR-20S2U1
|
|
endef
|
|
TARGET_DEVICES += haier_har-20s2u1
|
|
|
|
define Device/hilink_hlk-7621a-evb
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := HiLink
|
|
DEVICE_MODEL := HLK-7621A evaluation board
|
|
DEVICE_PACKAGES += kmod-mt76x2 kmod-usb3
|
|
IMAGE_SIZE := 32448k
|
|
endef
|
|
TARGET_DEVICES += hilink_hlk-7621a-evb
|
|
|
|
define Device/hiwifi_hc5962
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 32768k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_VENDOR := HiWiFi
|
|
DEVICE_MODEL := HC5962
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += hiwifi_hc5962
|
|
|
|
define Device/humax_e10
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15936k
|
|
DEVICE_VENDOR := HUMAX
|
|
DEVICE_MODEL := E10
|
|
DEVICE_ALT0_VENDOR := HUMAX
|
|
DEVICE_ALT0_MODEL := QUANTUM E10
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
|
|
edimax-header -s CSYS -m EA03 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
edimax-header -s CSYS -m EA03 -f 0x70000 -S 0x01100000 | \
|
|
check-size | zip upg -P f013c26cf0a320fb71d03356dcb6bb63
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += humax_e10
|
|
|
|
define Device/iodata_wn-ax1167gr
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15552k
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AX1167GR
|
|
ARTIFACTS := initramfs-factory.bin
|
|
ARTIFACT/initramfs-factory.bin := append-image-stage initramfs-kernel.bin | \
|
|
check-size 7680k | senao-header -r 0x30a -p 0x1055 -t 4
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ax1167gr
|
|
|
|
define Device/iodata_nand
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := I-O DATA
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 51200k
|
|
LOADER_TYPE := bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | lzma | uImage lzma
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
# The OEM webinterface expects an kernel with initramfs which has the uImage
|
|
# header field ih_name.
|
|
# We don't want to set the header name field for the kernel include in the
|
|
# sysupgrade image as well, as this image shouldn't be accepted by the OEM
|
|
# webinterface. It will soft-brick the board.
|
|
|
|
define Device/iodata_wn-ax1167gr2
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-AX1167GR2
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d42 -n '3.10(XBC.1)b10' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ax1167gr2
|
|
|
|
define Device/iodata_wn-ax2033gr
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-AX2033GR
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d42 -n '3.10(VST.1)C10' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ax2033gr
|
|
|
|
define Device/iodata_wn-dx1167r
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-DX1167R
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d43 -n '3.10(XIK.1)b10' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-dx1167r
|
|
|
|
define Device/iodata_wn-dx1200gr
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-DX1200GR
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d43 -n '3.10(XIQ.0)b20' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-dx1200gr
|
|
|
|
define Device/iodata_wn-dx2033gr
|
|
$(Device/iodata_nand)
|
|
DEVICE_MODEL := WN-DX2033GR
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
uImage lzma -M 0x434f4d42 -n '3.10(XID.0)b30' | iodata-mstc-header
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-dx2033gr
|
|
|
|
define Device/iodata_wn-gx300gr
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7616k
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-GX300GR
|
|
DEVICE_PACKAGES := kmod-mt7603
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-gx300gr
|
|
|
|
define Device/iodata_wnpr2600g
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WNPR2600G
|
|
IMAGE_SIZE := 13952k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
elx-header 0104003a 8844A2D168B45A2D
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iodata_wnpr2600g
|
|
|
|
define Device/iptime_a3002mesh
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a3002me
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A3002MESH
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += iptime_a3002mesh
|
|
|
|
define Device/iptime_a3004ns-dual
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a3004nd
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A3004NS-dual
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt76x2 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += iptime_a3004ns-dual
|
|
|
|
define Device/iptime_a3004t
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UIMAGE_NAME := a3004t
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A3004T
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += iptime_a3004t
|
|
|
|
define Device/iptime_a6004ns-m
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a6004nm
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A6004NS-M
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += iptime_a6004ns-m
|
|
|
|
define Device/iptime_a6ns-m
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a6nm
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A6ns-M
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += iptime_a6ns-m
|
|
|
|
define Device/iptime_a8004t
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16128k
|
|
UIMAGE_NAME := a8004t
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := A8004T
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += iptime_a8004t
|
|
|
|
define Device/iptime_ax2004m
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 121344k
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGES += recovery.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/recovery.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size | iptime-crc32 ax2004m
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := AX2004M
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += iptime_ax2004m
|
|
|
|
define Device/iptime_t5004
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UBINIZE_OPTS := -E 5
|
|
UIMAGE_NAME := t5004
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := ipTIME
|
|
DEVICE_MODEL := T5004
|
|
DEVICE_PACKAGES := -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += iptime_t5004
|
|
|
|
define Device/jcg_jhr-ac876m
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 89.1
|
|
JCG_MAXSIZE := 16064k
|
|
DEVICE_VENDOR := JCG
|
|
DEVICE_MODEL := JHR-AC876M
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += jcg_jhr-ac876m
|
|
|
|
define Device/jcg_q20
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 91136k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_VENDOR := JCG
|
|
DEVICE_MODEL := Q20
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += jcg_q20
|
|
|
|
define Device/jcg_y2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 95.1
|
|
JCG_MAXSIZE := 16064k
|
|
DEVICE_VENDOR := JCG
|
|
DEVICE_MODEL := Y2
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += jcg_y2
|
|
|
|
define Device/keenetic_kn-3010
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 31488k
|
|
DEVICE_VENDOR := Keenetic
|
|
DEVICE_MODEL := KN-3010
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | pad-to $$$$(BLOCKSIZE) | \
|
|
check-size | zyimage -d 8400912 -v "KN-3010"
|
|
endef
|
|
TARGET_DEVICES += keenetic_kn-3010
|
|
|
|
define Device/lenovo_newifi-d1
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := Newifi
|
|
DEVICE_MODEL := D1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += newifi-d1
|
|
endef
|
|
TARGET_DEVICES += lenovo_newifi-d1
|
|
|
|
define Device/linksys_e5600
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := E5600
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
uboot-envtools
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | check-size | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | gemtek-trailer
|
|
endef
|
|
TARGET_DEVICES += linksys_e5600
|
|
|
|
define Device/linksys_e7350
|
|
$(Device/belkin_rt1800)
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := E7350
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | belkin-header GOLF 1 9.9.9
|
|
endef
|
|
TARGET_DEVICES += linksys_e7350
|
|
|
|
define Device/linksys_ea7xxx
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 36864k
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615-firmware \
|
|
uboot-envtools
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES := sysupgrade.bin factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | check-size | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | linksys-image type=$$$$(LINKSYS_HWNAME)
|
|
endef
|
|
|
|
define Device/linksys_ea6350-v4
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA6350
|
|
DEVICE_VARIANT := v4
|
|
LINKSYS_HWNAME := EA6350
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7663-firmware-ap
|
|
endef
|
|
TARGET_DEVICES += linksys_ea6350-v4
|
|
|
|
define Device/linksys_ea7300-v1
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA7300
|
|
DEVICE_VARIANT := v1
|
|
LINKSYS_HWNAME := EA7300
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7300-v1
|
|
|
|
define Device/linksys_ea7300-v2
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA7300
|
|
DEVICE_VARIANT := v2
|
|
LINKSYS_HWNAME := EA7300v2
|
|
DEVICE_PACKAGES += kmod-mt7603
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7300-v2
|
|
|
|
define Device/linksys_ea7500-v2
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA7500
|
|
DEVICE_VARIANT := v2
|
|
LINKSYS_HWNAME := EA7500v2
|
|
endef
|
|
TARGET_DEVICES += linksys_ea7500-v2
|
|
|
|
define Device/linksys_ea8100-v1
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA8100
|
|
DEVICE_VARIANT := v1
|
|
LINKSYS_HWNAME := EA8100
|
|
endef
|
|
TARGET_DEVICES += linksys_ea8100-v1
|
|
|
|
define Device/linksys_ea8100-v2
|
|
$(Device/linksys_ea7xxx)
|
|
DEVICE_MODEL := EA8100
|
|
DEVICE_VARIANT := v2
|
|
LINKSYS_HWNAME := EA8100v2
|
|
endef
|
|
TARGET_DEVICES += linksys_ea8100-v2
|
|
|
|
define Device/linksys_re6500
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := RE6500
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
|
SUPPORTED_DEVICES += re6500
|
|
endef
|
|
TARGET_DEVICES += linksys_re6500
|
|
|
|
define Device/mediatek_ap-mt7621a-v60
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := Mediatek
|
|
DEVICE_MODEL := AP-MT7621A-V60 EVB
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-sdhci-mt7620 kmod-sound-mt7620 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += mediatek_ap-mt7621a-v60
|
|
|
|
define Device/mediatek_mt7621-eval-board
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 15104k
|
|
DEVICE_VENDOR := MediaTek
|
|
DEVICE_MODEL := MT7621 EVB
|
|
DEVICE_PACKAGES := -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += mt7621
|
|
endef
|
|
TARGET_DEVICES += mediatek_mt7621-eval-board
|
|
|
|
define Device/MikroTik
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := MikroTik
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_PACKAGES := kmod-usb3
|
|
KERNEL_NAME := vmlinuz
|
|
KERNEL := kernel-bin | append-dtb-elf
|
|
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 | \
|
|
pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | \
|
|
append-metadata
|
|
endef
|
|
|
|
define Device/mikrotik_ltap-2hnd
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := LtAP-2HnD
|
|
DEVICE_PACKAGES += kmod-ath9k kmod-pps-gpio rssileds
|
|
endef
|
|
TARGET_DEVICES += mikrotik_ltap-2hnd
|
|
|
|
define Device/mikrotik_routerboard-750gr3
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD 750Gr3
|
|
DEVICE_PACKAGES += -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += mikrotik,rb750gr3
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-750gr3
|
|
|
|
define Device/mikrotik_routerboard-760igs
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD 760iGS
|
|
DEVICE_PACKAGES += kmod-sfp -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-760igs
|
|
|
|
define Device/mikrotik_routerboard-m11g
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD M11G
|
|
DEVICE_PACKAGES := -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += mikrotik,rbm11g
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-m11g
|
|
|
|
define Device/mikrotik_routerboard-m33g
|
|
$(Device/MikroTik)
|
|
DEVICE_MODEL := RouterBOARD M33G
|
|
DEVICE_PACKAGES := -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += mikrotik,rbm33g
|
|
endef
|
|
TARGET_DEVICES += mikrotik_routerboard-m33g
|
|
|
|
define Device/mqmaker_witi
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := MQmaker
|
|
DEVICE_MODEL := WiTi
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-sdhci-mt7620 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += witi mqmaker,witi-256m mqmaker,witi-512m
|
|
endef
|
|
TARGET_DEVICES += mqmaker_witi
|
|
|
|
define Device/mtc_wr1201
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_VENDOR := MTC
|
|
DEVICE_MODEL := Wireless Router WR1201
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'WR1201_8_128'
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += mtc_wr1201
|
|
|
|
define Device/mts_wg430223
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := MTS
|
|
DEVICE_MODEL := WG430223
|
|
IMAGE_SIZE := 32768k
|
|
KERNEL_SIZE := 4352k
|
|
UBINIZE_OPTS := -E 5
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none | arcadyan-trx 0x53485231 | pad-to $$(KERNEL_SIZE)
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none
|
|
IMAGES += factory.trx
|
|
IMAGE/factory.trx := append-kernel | append-ubi | check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware uboot-envtools uencrypt
|
|
endef
|
|
TARGET_DEVICES += mts_wg430223
|
|
|
|
define Device/netgear_ex6150
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := EX6150
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
|
NETGEAR_BOARD_ID := U12H318T00_NETGEAR
|
|
IMAGE_SIZE := 14848k
|
|
IMAGES += factory.chk
|
|
IMAGE/factory.chk := $$(sysupgrade_bin) | check-size | netgear-chk
|
|
endef
|
|
TARGET_DEVICES += netgear_ex6150
|
|
|
|
define Device/netgear_sercomm_nand
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.img kernel.bin rootfs.bin
|
|
IMAGE/factory.img := pad-extra 2048k | append-kernel | pad-to 6144k | \
|
|
append-ubi | pad-to $$$$(BLOCKSIZE) | sercom-footer | pad-to 128 | \
|
|
zip $$$$(SERCOMM_HWNAME).bin | sercom-seal
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/kernel.bin := append-kernel
|
|
IMAGE/rootfs.bin := append-ubi | check-size
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
|
|
define Device/netgear_r6220
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6220
|
|
SERCOMM_HWNAME := R6220
|
|
SERCOMM_HWID := AYA
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0086
|
|
IMAGE_SIZE := 28672k
|
|
DEVICE_PACKAGES += kmod-mt76x2
|
|
SUPPORTED_DEVICES += r6220
|
|
endef
|
|
TARGET_DEVICES += netgear_r6220
|
|
|
|
|
|
define Device/netgear_r6260
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6260
|
|
SERCOMM_HWNAME := R6260
|
|
SERCOMM_HWID := CHJ
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0052
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6260
|
|
|
|
define Device/netgear_r6350
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6350
|
|
SERCOMM_HWNAME := R6350
|
|
SERCOMM_HWID := CHJ
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0052
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6350
|
|
|
|
define Device/netgear_r6700-v2
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6700
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_ALT0_VENDOR := NETGEAR
|
|
DEVICE_ALT0_MODEL := Nighthawk AC2400
|
|
DEVICE_ALT0_VARIANT := v1
|
|
DEVICE_ALT1_VENDOR := NETGEAR
|
|
DEVICE_ALT1_MODEL := Nighthawk AC2100
|
|
DEVICE_ALT1_VARIANT := v1
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6700-v2
|
|
|
|
define Device/netgear_r6800
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6800
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0062
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6800
|
|
|
|
define Device/netgear_r6850
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6850
|
|
SERCOMM_HWNAME := R6850
|
|
SERCOMM_HWID := CHJ
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0052
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6850
|
|
|
|
define Device/netgear_r6900-v2
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R6900
|
|
DEVICE_VARIANT := v2
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r6900-v2
|
|
|
|
define Device/netgear_r7200
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R7200
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r7200
|
|
|
|
define Device/netgear_r7450
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := R7450
|
|
SERCOMM_HWNAME := R6950
|
|
SERCOMM_HWID := BZV
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1032
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_r7450
|
|
|
|
define Device/netgear_wac104
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := WAC104
|
|
SERCOMM_HWNAME := WAC104
|
|
SERCOMM_HWID := CAY
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x0006
|
|
IMAGE_SIZE := 28672k
|
|
DEVICE_PACKAGES += kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += netgear_wac104
|
|
|
|
define Device/netgear_wac124
|
|
$(Device/netgear_sercomm_nand)
|
|
DEVICE_MODEL := WAC124
|
|
SERCOMM_HWNAME := WAC124
|
|
SERCOMM_HWID := CTL
|
|
SERCOMM_HWVER := A003
|
|
SERCOMM_SWVER := 0x0402
|
|
IMAGE_SIZE := 40960k
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += netgear_wac124
|
|
|
|
define Device/netgear_wax202
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_MODEL := WAX202
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
NETGEAR_ENC_MODEL := WAX202
|
|
NETGEAR_ENC_REGION := US
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 38912k
|
|
KERNEL_SIZE := 4096k
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
|
append-squashfs4-fakeroot
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | netgear-encrypted-factory
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += netgear_wax202
|
|
|
|
define Device/netgear_wndr3700-v5
|
|
$(Device/dsa-migration)
|
|
$(Device/netgear_sercomm_nor)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := WNDR3700
|
|
DEVICE_VARIANT := v5
|
|
SERCOMM_HWNAME := WNDR3700v5
|
|
SERCOMM_HWID := AYB
|
|
SERCOMM_HWVER := A001
|
|
SERCOMM_SWVER := 0x1054
|
|
SERCOMM_PAD := 320k
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += wndr3700v5
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3700-v5
|
|
|
|
define Device/netis_wf2881
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UBINIZE_OPTS := -E 5
|
|
UIMAGE_NAME := WF2881_0.0.00
|
|
KERNEL_INITRAMFS := $$(KERNEL) | netis-tail WF2881
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_VENDOR := NETIS
|
|
DEVICE_MODEL := WF2881
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += netis_wf2881
|
|
|
|
define Device/oraybox_x3a
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15360k
|
|
DEVICE_VENDOR := OrayBox
|
|
DEVICE_MODEL := X3A
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += oraybox_x3a
|
|
|
|
define Device/phicomm_k2p
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15744k
|
|
DEVICE_VENDOR := Phicomm
|
|
DEVICE_MODEL := K2P
|
|
DEVICE_ALT0_VENDOR := Phicomm
|
|
DEVICE_ALT0_MODEL := KE 2P
|
|
SUPPORTED_DEVICES += k2p
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += phicomm_k2p
|
|
|
|
define Device/planex_vr500
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 65216k
|
|
DEVICE_VENDOR := Planex
|
|
DEVICE_MODEL := VR500
|
|
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += vr500
|
|
endef
|
|
TARGET_DEVICES += planex_vr500
|
|
|
|
define Device/raisecom_msg1500-x-00
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 129280k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := RAISECOM
|
|
DEVICE_MODEL := MSG1500
|
|
DEVICE_VARIANT := X.00
|
|
DEVICE_ALT0_VENDOR := Nokia
|
|
DEVICE_ALT0_MODEL := A-040W-Q
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += raisecom_msg1500-x-00
|
|
|
|
define Device/renkforce_ws-wn530hp3-a
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Renkforce
|
|
DEVICE_MODEL := WS-WN530HP3-A
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 65536 | append-rootfs | \
|
|
check-size | append-metadata
|
|
IMAGE_SIZE := 15040k
|
|
endef
|
|
TARGET_DEVICES += renkforce_ws-wn530hp3-a
|
|
|
|
define Device/rostelecom_rt-sf-1
|
|
$(Device/sercomm_dxx)
|
|
IMAGE_SIZE := 32768k
|
|
SERCOMM_HWID := DKG
|
|
SERCOMM_HWVER := 10110
|
|
SERCOMM_SWVER := 1026
|
|
DEVICE_VENDOR := Rostelecom
|
|
DEVICE_MODEL := RT-SF-1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware \
|
|
kmod-usb3 uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += rostelecom_rt-sf-1
|
|
|
|
define Device/samknows_whitebox-v8
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := SamKnows
|
|
DEVICE_MODEL := Whitebox 8
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
SUPPORTED_DEVICES += sk-wb8
|
|
endef
|
|
TARGET_DEVICES += samknows_whitebox-v8
|
|
|
|
define Device/sercomm_na502
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 20480k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
DEVICE_VENDOR := SERCOMM
|
|
DEVICE_MODEL := NA502
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-mt7603 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += sercomm_na502
|
|
|
|
define Device/sercomm_na502s
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 20971520
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
DEVICE_VENDOR := SERCOMM
|
|
DEVICE_MODEL := NA502S
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-mt7603 kmod-usb3 kmod-usb-serial \
|
|
kmod-usb-serial-xr_usb_serial_common
|
|
endef
|
|
TARGET_DEVICES += sercomm_na502s
|
|
|
|
define Device/sim_simax1800t
|
|
$(Device/haier-sim_wr1800k)
|
|
DEVICE_VENDOR := SIM
|
|
DEVICE_MODEL := SIMAX1800T
|
|
endef
|
|
TARGET_DEVICES += sim_simax1800t
|
|
|
|
define Device/snr_snr-cpe-me2-lite
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := SNR
|
|
DEVICE_MODEL := SNR-CPE-ME2-Lite
|
|
UIMAGE_NAME := $$(DEVICE_MODEL)
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
endef
|
|
TARGET_DEVICES += snr_snr-cpe-me2-lite
|
|
|
|
define Device/storylink_sap-g3200u3
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := STORYLiNK
|
|
DEVICE_MODEL := SAP-G3200U3
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += sap-g3200u3
|
|
endef
|
|
TARGET_DEVICES += storylink_sap-g3200u3
|
|
|
|
define Device/telco-electronics_x1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Telco Electronics
|
|
DEVICE_MODEL := X1
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt76
|
|
endef
|
|
TARGET_DEVICES += telco-electronics_x1
|
|
|
|
define Device/tenbay_t-mb5eu-v01
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Tenbay
|
|
DEVICE_MODEL := T-MB5EU-V01
|
|
DEVICE_DTS_CONFIG := config@1
|
|
DEVICE_PACKAGES += kmod-mt7915-firmware kmod-usb3
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGE_SIZE := 15808k
|
|
SUPPORTED_DEVICES += mt7621-dm2-t-mb5eu-v01-nor
|
|
endef
|
|
TARGET_DEVICES += tenbay_t-mb5eu-v01
|
|
|
|
define Device/thunder_timecloud
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Thunder
|
|
DEVICE_MODEL := Timecloud
|
|
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += timecloud
|
|
endef
|
|
TARGET_DEVICES += thunder_timecloud
|
|
|
|
define Device/totolink_a7000r
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := C8340R1C-9999
|
|
DEVICE_VENDOR := TOTOLINK
|
|
DEVICE_MODEL := A7000R
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += totolink_a7000r
|
|
|
|
define Device/totolink_x5000r
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := C8343R-9999
|
|
DEVICE_VENDOR := TOTOLINK
|
|
DEVICE_MODEL := X5000R
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
endef
|
|
TARGET_DEVICES += totolink_x5000r
|
|
|
|
define Device/tplink_archer-a6-v3
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := Archer A6
|
|
DEVICE_VARIANT := V3
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e \
|
|
kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := ARCHER-A6-V3
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
IMAGE_SIZE := 15744k
|
|
endef
|
|
TARGET_DEVICES += tplink_archer-a6-v3
|
|
|
|
define Device/tplink_archer-c6-v3
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := Archer C6
|
|
DEVICE_VARIANT := V3
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e \
|
|
kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := ARCHER-C6-V3
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
IMAGE_SIZE := 15744k
|
|
endef
|
|
TARGET_DEVICES += tplink_archer-c6-v3
|
|
|
|
define Device/tplink_archer-c6u-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := Archer C6U
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 \
|
|
kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
TPLINK_BOARD_ID := ARCHER-C6U-V1
|
|
IMAGE_SIZE := 15744k
|
|
endef
|
|
TARGET_DEVICES += tplink_archer-c6u-v1
|
|
|
|
define Device/tplink_eap235-wall-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := EAP235-Wall
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := EAP235-WALL-V1
|
|
IMAGE_SIZE := 13440k
|
|
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory | \
|
|
pad-extra 128
|
|
endef
|
|
TARGET_DEVICES += tplink_eap235-wall-v1
|
|
|
|
define Device/tplink_eap615-wall-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := EAP615-Wall
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
TPLINK_BOARD_ID := EAP615-WALL-V1
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | pad-to 64k
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
|
|
IMAGE_SIZE := 13248k
|
|
endef
|
|
TARGET_DEVICES += tplink_eap615-wall-v1
|
|
|
|
define Device/tplink_ec330-g5u-v1
|
|
$(Device/dsa-migration)
|
|
LOADER := bin
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 49152k
|
|
DEVICE_VENDOR := TP-Link
|
|
DEVICE_MODEL := EC330-G5u
|
|
DEVICE_ALT0_VENDOR := TP-Link
|
|
DEVICE_ALT0_MODEL := Archer C9ERT
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb-ledtrig-usbport \
|
|
kmod-usb3 uboot-envtools
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage-tplink-c9 standalone '$(call toupper,$(LINUX_KARCH)) \
|
|
$(VERSION_DIST) Linux-$(LINUX_VERSION)' | \
|
|
uImage-tplink-c9 firmware 'OS IMAGE ($(VERSION_DIST))'
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
uImage none
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata | check-size
|
|
endef
|
|
TARGET_DEVICES += tplink_ec330-g5u-v1
|
|
|
|
define Device/tplink_er605-v2
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := TP-Link
|
|
DEVICE_MODEL := ER605
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := -wpad-basic-wolfssl kmod-usb3
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
KERNEL_IN_UBI := 1
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGES += sysupgrade.tar
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE_SIZE := 127744k
|
|
endef
|
|
TARGET_DEVICES += tplink_er605-v2
|
|
|
|
define Device/tplink_mr600-v2-eu
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-v2)
|
|
DEVICE_MODEL := MR600
|
|
DEVICE_VARIANT := v2 (EU)
|
|
TPLINK_FLASHLAYOUT := 16Mltq
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
kmod-usb-net-qmi-wwan uqmi kmod-usb3
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
KERNEL_INITRAMFS := $$(KERNEL) | tplink-v2-header
|
|
TPLINK_BOARD_ID := MR600-V2-EU
|
|
IMAGE_SIZE := 16384k
|
|
endef
|
|
TARGET_DEVICES += tplink_mr600-v2-eu
|
|
|
|
define Device/tplink_re350-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE350
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
TPLINK_BOARD_ID := RE350-V1
|
|
IMAGE_SIZE := 6016k
|
|
SUPPORTED_DEVICES += re350-v1
|
|
endef
|
|
TARGET_DEVICES += tplink_re350-v1
|
|
|
|
define Device/tplink_re500-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE500
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
TPLINK_BOARD_ID := RE500-V1
|
|
IMAGE_SIZE := 14208k
|
|
endef
|
|
TARGET_DEVICES += tplink_re500-v1
|
|
|
|
define Device/tplink_re650-v1
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE650
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
TPLINK_BOARD_ID := RE650-V1
|
|
IMAGE_SIZE := 14208k
|
|
endef
|
|
TARGET_DEVICES += tplink_re650-v1
|
|
|
|
define Device/tplink_re650-v2
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := RE650
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
|
TPLINK_BOARD_ID := RE650-V2
|
|
IMAGE_SIZE := 7994k
|
|
endef
|
|
TARGET_DEVICES += tplink_re650-v2
|
|
|
|
define Device/tplink_tl-wpa8631p-v3
|
|
$(Device/dsa-migration)
|
|
$(Device/tplink-safeloader)
|
|
DEVICE_MODEL := TL-WPA8631P
|
|
DEVICE_VARIANT := v3
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
|
TPLINK_BOARD_ID := TL-WPA8631P-V3
|
|
IMAGE_SIZE := 7232k
|
|
endef
|
|
TARGET_DEVICES += tplink_tl-wpa8631p-v3
|
|
|
|
define Device/ubnt_edgerouter_common
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
IMAGE_SIZE := 256768k
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SIZE := 3145728
|
|
KERNEL_INITRAMFS := $$(KERNEL) | \
|
|
ubnt-erx-factory-image $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.tar
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
DEVICE_PACKAGES += -wpad-basic-wolfssl
|
|
endef
|
|
|
|
define Device/ubnt_edgerouter-x
|
|
$(Device/ubnt_edgerouter_common)
|
|
DEVICE_MODEL := EdgeRouter X
|
|
SUPPORTED_DEVICES += ubnt-erx ubiquiti,edgerouterx
|
|
endef
|
|
TARGET_DEVICES += ubnt_edgerouter-x
|
|
|
|
define Device/ubnt_edgerouter-x-sfp
|
|
$(Device/ubnt_edgerouter_common)
|
|
DEVICE_MODEL := EdgeRouter X SFP
|
|
DEVICE_ALT0_VENDOR := Ubiquiti
|
|
DEVICE_ALT0_MODEL := EdgePoint R6
|
|
DEVICE_PACKAGES += kmod-i2c-algo-pca kmod-gpio-pca953x kmod-sfp
|
|
SUPPORTED_DEVICES += ubnt-erx-sfp ubiquiti,edgerouterx-sfp
|
|
endef
|
|
TARGET_DEVICES += ubnt_edgerouter-x-sfp
|
|
|
|
define Device/ubnt_unifi-6-lite
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi 6 Lite
|
|
DEVICE_DTS_CONFIG := config@1
|
|
DEVICE_DTS_LOADADDR := 0x87000000
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7915-firmware
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGE_SIZE := 15424k
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-6-lite
|
|
|
|
define Device/ubnt_unifi-flexhd
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi FlexHD
|
|
DEVICE_DTS_CONFIG := config@2
|
|
DEVICE_DTS_LOADADDR := 0x87000000
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615-firmware kmod-leds-ubnt-ledbar
|
|
IMAGE_SIZE := 15552k
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-flexhd
|
|
|
|
define Device/ubnt_unifi-nanohd
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi nanoHD
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615-firmware
|
|
IMAGE_SIZE := 15552k
|
|
endef
|
|
TARGET_DEVICES += ubnt_unifi-nanohd
|
|
|
|
define Device/ubnt_usw-flex
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Ubiquiti
|
|
DEVICE_MODEL := UniFi Switch Flex
|
|
DEVICE_DTS_CONFIG := config@1
|
|
DEVICE_DTS_LOADADDR := 0x87000000
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGE_SIZE := 14720k
|
|
endef
|
|
TARGET_DEVICES += ubnt_usw-flex
|
|
|
|
define Device/unielec_u7621-01-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-01
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-01-16m
|
|
|
|
define Device/unielec_u7621-06-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-06
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += u7621-06-256M-16M unielec,u7621-06-256m-16m
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-06-16m
|
|
|
|
define Device/unielec_u7621-06-32m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-06
|
|
DEVICE_VARIANT := 32M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += unielec,u7621-06-32m
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-06-32m
|
|
|
|
define Device/unielec_u7621-06-64m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 65216k
|
|
DEVICE_VENDOR := UniElec
|
|
DEVICE_MODEL := U7621-06
|
|
DEVICE_VARIANT := 64M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += unielec,u7621-06-512m-64m
|
|
endef
|
|
TARGET_DEVICES += unielec_u7621-06-64m
|
|
|
|
define Device/wavlink_wl-wn531a6
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Wavlink
|
|
DEVICE_MODEL := WL-WN531A6
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware kmod-usb3
|
|
IMAGE_SIZE := 15040k
|
|
endef
|
|
TARGET_DEVICES += wavlink_wl-wn531a6
|
|
|
|
define Device/wavlink_wl-wn533a8
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := Wavlink
|
|
DEVICE_MODEL := WL-WN533A8
|
|
KERNEL_INITRAMFS_SUFFIX := -WN533A8$$(KERNEL_SUFFIX)
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3
|
|
IMAGE_SIZE := 15040k
|
|
endef
|
|
TARGET_DEVICES += wavlink_wl-wn533a8
|
|
|
|
define Device/wavlink_ws-wn572hp3-4g
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 64k
|
|
DEVICE_VENDOR := Wavlink
|
|
DEVICE_MODEL := WS-WN572HP3
|
|
DEVICE_VARIANT := 4G
|
|
IMAGE_SIZE := 15040k
|
|
KERNEL_LOADADDR := 0x82000000
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | append-metadata
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
kmod-usb3 kmod-usb-net-rndis comgt-ncm
|
|
endef
|
|
TARGET_DEVICES += wavlink_ws-wn572hp3-4g
|
|
|
|
define Device/wevo_11acnas
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := 11AC-NAS-Router(0.0.0)
|
|
DEVICE_VENDOR := WeVO
|
|
DEVICE_MODEL := 11AC NAS Router
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += 11acnas
|
|
endef
|
|
TARGET_DEVICES += wevo_11acnas
|
|
|
|
define Device/wevo_w2914ns-v2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
UIMAGE_NAME := W2914NS-V2(0.0.0)
|
|
DEVICE_VENDOR := WeVO
|
|
DEVICE_MODEL := W2914NS
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += w2914nsv2
|
|
endef
|
|
TARGET_DEVICES += wevo_w2914ns-v2
|
|
|
|
define Device/winstars_ws-wn583a6
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 7872k
|
|
DEVICE_VENDOR := Winstars
|
|
DEVICE_MODEL := WS-WN583A6
|
|
DEVICE_ALT0_VENDOR := Gemeita
|
|
DEVICE_ALT0_MODEL := AC2100
|
|
KERNEL_INITRAMFS_SUFFIX := -WN583A6$$(KERNEL_SUFFIX)
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += winstars_ws-wn583a6
|
|
|
|
define Device/xiaomi_nand_separate
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += kernel1.bin rootfs0.bin
|
|
IMAGE/kernel1.bin := append-kernel
|
|
IMAGE/rootfs0.bin := append-ubi | check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/xiaomi_mi-router-3g
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Mi Router 3G
|
|
IMAGE_SIZE := 124416k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += R3G mir3g xiaomi,mir3g
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-3g
|
|
|
|
define Device/xiaomi_mi-router-3g-v2
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 14848k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 3G
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
SUPPORTED_DEVICES += xiaomi,mir3g-v2
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-3g-v2
|
|
|
|
define Device/xiaomi_mi-router-3-pro
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE:= 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 255488k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 3 Pro
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
SUPPORTED_DEVICES += xiaomi,mir3p
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-3-pro
|
|
|
|
define Device/xiaomi_mi-router-4
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Mi Router 4
|
|
IMAGE_SIZE := 124416k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-4
|
|
|
|
define Device/xiaomi_mi-router-4a-gigabit
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 14848k
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 4A
|
|
DEVICE_VARIANT := Gigabit Edition
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-4a-gigabit
|
|
|
|
define Device/xiaomi_mi-router-ac2100
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Mi Router AC2100
|
|
IMAGE_SIZE := 120320k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-ac2100
|
|
|
|
define Device/xiaomi_mi-router-cr660x
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
DEVICE_VENDOR := Xiaomi
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 128512k
|
|
IMAGES += firmware.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/firmware.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES += kmod-mt7915-firmware uboot-envtools
|
|
endef
|
|
|
|
define Device/xiaomi_mi-router-cr6606
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
DEVICE_MODEL := Mi Router CR6606
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6606
|
|
|
|
define Device/xiaomi_mi-router-cr6608
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
DEVICE_MODEL := Mi Router CR6608
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6608
|
|
|
|
define Device/xiaomi_mi-router-cr6609
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
DEVICE_MODEL := Mi Router CR6609
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6609
|
|
|
|
define Device/xiaomi_redmi-router-ac2100
|
|
$(Device/xiaomi_nand_separate)
|
|
DEVICE_MODEL := Redmi Router AC2100
|
|
IMAGE_SIZE := 120320k
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615-firmware
|
|
endef
|
|
TARGET_DEVICES += xiaomi_redmi-router-ac2100
|
|
|
|
define Device/xiaoyu_xy-c5
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := XiaoYu
|
|
DEVICE_MODEL := XY-C5
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += xiaoyu_xy-c5
|
|
|
|
define Device/xzwifi_creativebox-v1
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := CreativeBox
|
|
DEVICE_MODEL := v1
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
|
kmod-usb3 -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += xzwifi_creativebox-v1
|
|
|
|
define Device/youhua_wr1200js
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := YouHua
|
|
DEVICE_MODEL := WR1200JS
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += youhua_wr1200js
|
|
|
|
define Device/youku_yk-l2
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Youku
|
|
DEVICE_MODEL := YK-L2
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
UIMAGE_MAGIC := 0x12291000
|
|
UIMAGE_NAME := 400000000000000000003000
|
|
endef
|
|
TARGET_DEVICES += youku_yk-l2
|
|
|
|
define Device/yuncore_ax820
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 15808k
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := AX820
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
endef
|
|
TARGET_DEVICES += yuncore_ax820
|
|
|
|
define Device/yuncore_fap640
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15808k
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := FAP640
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
endef
|
|
TARGET_DEVICES += yuncore_fap640
|
|
|
|
define Device/yuncore_fap690
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 15808k
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := FAP690
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
endef
|
|
TARGET_DEVICES += yuncore_fap690
|
|
|
|
define Device/zbtlink_zbt-we1326
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WE1326
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620
|
|
SUPPORTED_DEVICES += zbt-we1326
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-we1326
|
|
|
|
define Device/zbtlink_zbt-we3526
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WE3526
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-we3526
|
|
|
|
define Device/zbtlink_zbt-wg1602-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG1602
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg1602-16m
|
|
|
|
define Device/zbtlink_zbt-wg1602-v04-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG1602-V04
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg1602-v04-16m
|
|
|
|
define Device/zbtlink_zbt-wg1602-v04-32m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32128k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG1602-V04
|
|
DEVICE_VARIANT := 32M
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg1602-v04-32m
|
|
|
|
define Device/zbtlink_zbt-wg1608-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG1608
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt7615e \
|
|
kmod-mt7663-firmware-ap kmod-usb3 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg1608-16m
|
|
|
|
define Device/zbtlink_zbt-wg2626
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG2626
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += zbt-wg2626
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg2626
|
|
|
|
define Device/zbtlink_zbt-wg3526-16m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG3526
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += zbt-wg3526 zbt-wg3526-16M
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg3526-16m
|
|
|
|
define Device/zbtlink_zbt-wg3526-32m
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := Zbtlink
|
|
DEVICE_MODEL := ZBT-WG3526
|
|
DEVICE_VARIANT := 32M
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
SUPPORTED_DEVICES += ac1200pro zbt-wg3526-32M
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wg3526-32m
|
|
|
|
define Device/zio_freezio
|
|
$(Device/dsa-migration)
|
|
IMAGE_SIZE := 16064k
|
|
DEVICE_VENDOR := ZIO
|
|
DEVICE_MODEL := FREEZIO
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zio_freezio
|
|
|
|
define Device/zyxel_lte3301-plus
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := LTE3301-PLUS
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
|
uboot-envtools kmod-usb-ledtrig-usbport kmod-usb-net-qmi-wwan \
|
|
kmod-usb-serial-option uqmi
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma | \
|
|
zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | \
|
|
zytrx-header $$(DEVICE_MODEL) 9.99(ABQU.1)$$(VERSION_DIST)-recovery
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += zyxel_lte3301-plus
|
|
|
|
define Device/zyxel_nr7101
|
|
$(Device/dsa-migration)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NR7101
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 uboot-envtools kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) 9.99(ABUV.9)$$(VERSION_DIST)-recovery
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += zyxel_nr7101
|
|
|
|
define Device/zyxel_nwa-ax
|
|
$(Device/dsa-migration)
|
|
DEVICE_VENDOR := ZyXEL
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 8192k
|
|
UBINIZE_OPTS := -E 5
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware uboot-envtools zyxel-bootconfig
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
IMAGES += factory.bin ramboot-factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | zyxel-nwa-fit
|
|
IMAGE/ramboot-factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/zyxel_nwa50ax
|
|
$(Device/zyxel_nwa-ax)
|
|
DEVICE_MODEL := NWA50AX
|
|
endef
|
|
TARGET_DEVICES += zyxel_nwa50ax
|
|
|
|
define Device/zyxel_nwa55axe
|
|
$(Device/zyxel_nwa-ax)
|
|
DEVICE_MODEL := NWA55AXE
|
|
endef
|
|
TARGET_DEVICES += zyxel_nwa55axe
|
|
|
|
define Device/zyxel_wap6805
|
|
$(Device/dsa-migration)
|
|
$(Device/uimage-lzma-loader)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 32448k
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := WAP6805
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7621-qtn-rgmii
|
|
KERNEL := $$(KERNEL/lzma-loader) | uImage none | uimage-padhdr 160
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += zyxel_wap6805
|