mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 14:37:57 +00:00
mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This commit is contained in:
Chukun Pan
Daniel Golle
parent
9d1e687da3
commit
641e4f2f04
@ -34,9 +34,13 @@ bananapi,bpi-r3)
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
xiaomi,redmi-router-ax6000)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000"
|
||||
ubootenv_add_uci_sys_config "/dev/mtd2" "0x0" "0x10000" "0x20000"
|
||||
;;
|
||||
esac
|
||||
|
||||
config_load ubootenv
|
||||
config_foreach ubootenv_add_app_config ubootenv
|
||||
config_foreach ubootenv_add_app_config
|
||||
|
||||
exit 0
|
||||
|
||||
255
target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts
Normal file
255
target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts
Normal file
@ -0,0 +1,255 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
#include "mt7986a.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Xiaomi Redmi Router AX6000";
|
||||
compatible = "xiaomi,redmi-router-ax6000", "mediatek,mt7986a";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x20000000>;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
mesh {
|
||||
label = "mesh";
|
||||
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_9>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
nvmem-cells = <&macaddr_factory_4>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
mac-address-increment = <(-1)>;
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
mdio: mdio-bus {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
switch: switch@0 {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <31>;
|
||||
reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi_flash_pins: spi-flash-pins-33-to-38 {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
conf-pu {
|
||||
pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
|
||||
drive-strength = <8>;
|
||||
mediatek,pull-up-adv = <0>; /* bias-disable */
|
||||
};
|
||||
conf-pd {
|
||||
pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
|
||||
drive-strength = <8>;
|
||||
mediatek,pull-down-adv = <0>; /* bias-disable */
|
||||
};
|
||||
};
|
||||
|
||||
wf_2g_5g_pins: wf_2g_5g-pins {
|
||||
mux {
|
||||
function = "wifi";
|
||||
groups = "wf_2g", "wf_5g";
|
||||
};
|
||||
conf {
|
||||
pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
|
||||
"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
|
||||
"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
|
||||
"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
|
||||
"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
|
||||
"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
|
||||
"WF1_TOP_CLK", "WF1_TOP_DATA";
|
||||
drive-strength = <4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi_flash_pins>;
|
||||
cs-gpios = <0>, <0>;
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "spi-nand";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
spi-max-frequency = <20000000>;
|
||||
spi-tx-buswidth = <4>;
|
||||
spi-rx-buswidth = <4>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x0 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "Nvram";
|
||||
reg = <0x100000 0x40000>;
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "Bdata";
|
||||
reg = <0x140000 0x40000>;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x200000>;
|
||||
read-only;
|
||||
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
reg = <0x4 0x6>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "crash";
|
||||
reg = <0x580000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5c0000 {
|
||||
label = "crash_log";
|
||||
reg = <0x5c0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* ubi partition is the result of squashing
|
||||
* consecutive stock partitions:
|
||||
* - ubi
|
||||
* - ubi1
|
||||
* - overlay
|
||||
*/
|
||||
partition@600000 {
|
||||
label = "ubi";
|
||||
reg = <0x600000 0x6e00000>;
|
||||
};
|
||||
|
||||
/* last 12 MiB is reserved for NMBM bad block table */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
label = "cpu";
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wf_2g_5g_pins>;
|
||||
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
@ -16,15 +16,38 @@ mediatek_setup_interfaces()
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan"
|
||||
ucidef_set_interface_macaddr "wan" "$(macaddr_add $(cat /sys/class/net/eth0/address) 1)"
|
||||
;;
|
||||
xiaomi,redmi-router-ax6000)
|
||||
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" wan
|
||||
;;
|
||||
*)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
mediatek_setup_macs()
|
||||
{
|
||||
local board="$1"
|
||||
local lan_mac=""
|
||||
local wan_mac=""
|
||||
local label_mac=""
|
||||
|
||||
case $board in
|
||||
xiaomi,redmi-router-ax6000)
|
||||
wan_mac=$(mtd_get_mac_ascii Bdata ethaddr_wan)
|
||||
label_mac=$wan_mac
|
||||
;;
|
||||
esac
|
||||
|
||||
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
||||
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
||||
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
||||
}
|
||||
|
||||
board_config_update
|
||||
board=$(board_name)
|
||||
mediatek_setup_interfaces $board
|
||||
mediatek_setup_macs $board
|
||||
board_config_flush
|
||||
|
||||
exit 0
|
||||
|
||||
@ -125,3 +125,17 @@ define Device/mediatek_mt7986b-rfb
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += mediatek_mt7986b-rfb
|
||||
|
||||
define Device/xiaomi_redmi-router-ax6000
|
||||
DEVICE_VENDOR := Xiaomi
|
||||
DEVICE_MODEL := Redmi Router AX6000
|
||||
DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
KERNEL_LOADADDR := 0x48000000
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += xiaomi_redmi-router-ax6000
|
||||
|
||||
Loading…
Reference in New Issue
Block a user