From 641e4f2f0479997c71ff6c1f1b63fb9b5c67e687 Mon Sep 17 00:00:00 2001 From: Chukun Pan Date: Sun, 18 Sep 2022 23:16:18 +0800 Subject: [PATCH] mediatek: add Xiaomi Redmi Router AX6000 support Hardware specification: SoC: MediaTek MT7986A 4x A53 Flash: ESMT F50L1G41LB 128 MB RAM: K4A4G165WF-BCWE 512 MB Ethernet: 4x 10/100/1000 Mbps WiFi1: MT7976GN 2.4GHz ax 4x4 WiFi2: MT7976AN 5GHz ax 4x4 Button: Mesh, Reset Flash instructions: 1. Gain ssh and serial port access, see the link below: https://openwrt.org/toh/xiaomi/redmi_ax6000#installation 2. Use ssh or serial port to log in to the router, and execute the following command: nvram set boot_wait=on nvram set flag_boot_rootfs=0 nvram set flag_boot_success=1 nvram set flag_last_success=1 nvram set flag_try_sys1_failed=8 nvram set flag_try_sys2_failed=8 nvram commit 3. Set a static ip on the ethernet interface of your computer (e.g. default: ip 192.168.31.100, gateway 192.168.31.1) 4. Download the initramfs image, rename it to initramfs.bin, and host it with the tftp server. 5. Interrupt U-Boot and run these commands: setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi) saveenv tftpboot initramfs.bin bootm 6. After openwrt boots up, use scp or luci web to upload sysupgrade.bin to upgrade. Revert to stock firmware: Restore mtdparts back to default, then use the vendor's recovery tool (Windows only). Signed-off-by: Chukun Pan --- .../uboot-envtools/files/mediatek_filogic | 6 +- .../mt7986a-xiaomi-redmi-router-ax6000.dts | 255 ++++++++++++++++++ .../filogic/base-files/etc/board.d/02_network | 23 ++ target/linux/mediatek/image/filogic.mk | 14 + 4 files changed, 297 insertions(+), 1 deletion(-) create mode 100644 target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index a29ec7d0ee2..fe986b2e4ea 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -34,9 +34,13 @@ bananapi,bpi-r3) ;; esac ;; +xiaomi,redmi-router-ax6000) + ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000" + ubootenv_add_uci_sys_config "/dev/mtd2" "0x0" "0x10000" "0x20000" + ;; esac config_load ubootenv -config_foreach ubootenv_add_app_config ubootenv +config_foreach ubootenv_add_app_config exit 0 diff --git a/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts b/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts new file mode 100644 index 00000000000..7c590d22e22 --- /dev/null +++ b/target/linux/mediatek/dts/mt7986a-xiaomi-redmi-router-ax6000.dts @@ -0,0 +1,255 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; +#include +#include + +#include "mt7986a.dtsi" + +/ { + model = "Xiaomi Redmi Router AX6000"; + compatible = "xiaomi,redmi-router-ax6000", "mediatek,mt7986a"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x20000000>; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + mesh { + label = "mesh"; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_factory_4>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <(-1)>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + }; +}; + +&mdio { + switch: switch@0 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <66 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&pio { + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + mediatek,pull-down-adv = <0>; /* bias-disable */ + }; + }; + + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + cs-gpios = <0>, <0>; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + spi-max-frequency = <20000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "Nvram"; + reg = <0x100000 0x40000>; + }; + + partition@140000 { + label = "Bdata"; + reg = <0x140000 0x40000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_4: macaddr@4 { + reg = <0x4 0x6>; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + read-only; + }; + + partition@580000 { + label = "crash"; + reg = <0x580000 0x40000>; + read-only; + }; + + partition@5c0000 { + label = "crash_log"; + reg = <0x5c0000 0x40000>; + read-only; + }; + + /* ubi partition is the result of squashing + * consecutive stock partitions: + * - ubi + * - ubi1 + * - overlay + */ + partition@600000 { + label = "ubi"; + reg = <0x600000 0x6e00000>; + }; + + /* last 12 MiB is reserved for NMBM bad block table */ + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan4"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan2"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&wmac { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wf_2g_5g_pins>; + + mediatek,mtd-eeprom = <&factory 0x0>; +}; + +&uart0 { + status = "okay"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index f7dc7a01e06..0f0a0fc86b1 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -16,15 +16,38 @@ mediatek_setup_interfaces() ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan" ucidef_set_interface_macaddr "wan" "$(macaddr_add $(cat /sys/class/net/eth0/address) 1)" ;; + xiaomi,redmi-router-ax6000) + ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" wan + ;; *) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan ;; esac } +mediatek_setup_macs() +{ + local board="$1" + local lan_mac="" + local wan_mac="" + local label_mac="" + + case $board in + xiaomi,redmi-router-ax6000) + wan_mac=$(mtd_get_mac_ascii Bdata ethaddr_wan) + label_mac=$wan_mac + ;; + esac + + [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac + [ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac + [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac +} + board_config_update board=$(board_name) mediatek_setup_interfaces $board +mediatek_setup_macs $board board_config_flush exit 0 diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index df890a41523..f7fc9e30d15 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -125,3 +125,17 @@ define Device/mediatek_mt7986b-rfb IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata endef TARGET_DEVICES += mediatek_mt7986b-rfb + +define Device/xiaomi_redmi-router-ax6000 + DEVICE_VENDOR := Xiaomi + DEVICE_MODEL := Redmi Router AX6000 + DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000 + DEVICE_DTS_DIR := ../dts + KERNEL_LOADADDR := 0x48000000 + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_IN_UBI := 1 + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += xiaomi_redmi-router-ax6000