This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
For the ARM arch on 6.6, DTS files are moved into their vendor directories,
mimicking arm64. Reflect this in the image Makefile.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add support for kernel 6.1 as testing kernel for qoriq. Refresh config
using `make kernel_oldconfig`.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
It's the A13-based Olinuxino Micro which has only wireless interfaces. The
A20-based board is a fully-fledged one which has an ethernet interface.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This device supports channel ranges 36-64 and 100-165, just like
others based on the same reference design, but its current DTS is
unnecessarily restricting these ranges to 36-48 and 149-165.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
In preparation for supporting kernel 6.6, where the DTS files are grouped into
vendors - similarly to what arm64 has been doing all along -, update the
SUNXI_DTS var of this board to prepend it with SUNXI_DTS_DIR.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Kernel 6.1.83 allows to select CONFIG_GPIO_VF610, deactivate it by
default.
This fixes compilation of the armsr/armv8 target.
Fixes: 2ad898e091 ("kernel: bump 6.1 to 6.1.83")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the A1 hardware revision of the DIR-3040.
It is an exact copy of the DIR-3060 save for some cosmetic changes to the housing.
Even going so far as having the same FCC ID.
Hardware specification:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HVSINA 128MB
RAM: Micron MT41K128M16JT-125 256MB
Ethernet: 5x 10/100/1000 Mbps
WiFi1: MT7615DN 2.4GHz N 2x2:2
WiFi2: MT7615DN 5GHz AC 2x2:2
WiFi3: MT7615N 5GHz AC 4x4:4
Button: WPS, Reset
Flash instructions:
OpenWrt can be installed via D-Link Recovery GUI:
NOTE: Seems to only work in Firefox on Windows.
Tried with Chrome on Windows, Firefox in Linux, and Chromium in Linux.
None of these other browsers worked.
1. Push and hold reset button (on the bottom of the device) until power led
starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the recovery mode GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
5. Call the recovery page for the device at http://192.168.0.1/
6. Use the provided emergency web GUI to upload and flash a new firmware to the device
Thanks to @Lucky1openwrt and @iivailo for creating the DIR-3060 DTS file and related changes,
so it was possible for me to adapt them to the DIR-3040, build images,
test and fix minor issues.
MAC Addresses:
| use | address | example |
| --- | --- | --- |
| LAN | label | f4:*:61 |
| WAN | label + 4 | f4:*:65 |
| WI1/2g | label + 2 | f4:*:63 |
| WI1/5g | label + 1 | f4:*:62 |
| WI2/5g | label + 3 | f4:*:64 |
The label MAC address was found in Factory, 0xe000
Checklist:
✓ nand
✓ ethernet
✓ button
✓ wifi2g
✓ wifi5g
✓ wifi5g
✓ mac
✓ led
Signed-off-by: Vince McKinsey <vincemckinsey@gmail.com>
On IIJ SA-W2, some multiple LEDs have no "function" property and only
"color" property is available for the newer binding of LED on Linux
Kernel.
9d93b6d091 ("mvebu: drop redundant label with new LED color/function
format") removes "label" property from LEDs, then, multiple "<color>:"
(ex.: "green:"/"red:") will be appeared and renamed to "<color>:_<num>"
(ex.: "green:_1", "green:_2", ...) by kernel.
log:
[ 1.911118] leds-gpio leds: Led green: renamed to green:_1 due to name collision
[ 1.918600] leds-gpio leds: Led red: renamed to red:_1 due to name collision
[ 1.925727] leds-gpio leds: Led green: renamed to green:_2 due to name collision
[ 1.933202] leds-gpio leds: Led red: renamed to red:_2 due to name collision
[ 1.940321] leds-gpio leds: Led green: renamed to green:_3 due to name collision
[ 1.947797] leds-gpio leds: Led red: renamed to red:_3 due to name collision
[ 1.954939] leds-gpio leds: Led green: renamed to green:_4 due to name collision
[ 1.962456] leds-gpio leds: Led green: renamed to green:_5 due to name collision
/sys/class/leds:
root@OpenWrt:/# ls /sys/class/leds/
green: green:_3 green:status red:_2
green:_1 green:_4 red: red:_3
green:_2 green:_5 red:_1 red:status
Fix this issue by adding missing "function" (and "function-enumerator")
property to those LEDs on IIJ SA-W2.
Fixes: 9d93b6d091 ("mvebu: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
On Fortinet FortiGate 30E/50E, some multiple LEDs have no "function"
property and only "color" property is available for the new binding of
LED on Linux Kernel.
9d93b6d091 ("mvebu: drop redundant label with new LED color/function
format") removes "label" property from LEDs, then, multiple "<color>:"
(ex.: "green:"/"red:"/"amber:") will be appeared as LED names and
renamed to "<color>:_<num>" (ex.: "green:_1", "green:_2", ...) by
kernel.
log:
[ 12.425170] leds-gpio gpio-leds: Led green: renamed to green:_1 due to name collision
[ 12.520390] leds-gpio gpio-leds: Led amber: renamed to amber:_1 due to name collision
[ 12.614931] leds-gpio gpio-leds: Led green: renamed to green:_2 due to name collision
[ 12.709895] leds-gpio gpio-leds: Led green: renamed to green:_3 due to name collision
[ 12.804439] leds-gpio gpio-leds: Led amber: renamed to amber:_2 due to name collision
[ 12.898969] leds-gpio gpio-leds: Led green: renamed to green:_4 due to name collision
[ 12.993504] leds-gpio gpio-leds: Led amber: renamed to amber:_3 due to name collision
[ 13.088033] leds-gpio gpio-leds: Led green: renamed to green:_5 due to name collision
[ 13.182570] leds-gpio gpio-leds: Led green: renamed to green:_6 due to name collision
[ 13.277103] leds-gpio gpio-leds: Led amber: renamed to amber:_4 due to name collision
[ 13.371636] leds-gpio gpio-leds: Led green: renamed to green:_7 due to name collision
/sys/class/leds:
root@OpenWrt:/# ls /sys/class/leds/
amber: amber:_4 green:_2 green:_6 red:alarm
amber:_1 amber:alarm green:_3 green:_7 red:status
amber:_2 green: green:_4 green:status
amber:_3 green:_1 green:_5 red:
Fix this issue by adding missing "function" (and "function-enumerator")
property those to LEDs on Fortinet FortiGate devices.
Note: there is no appropriate function for "ha" LEDs in
dt-bindings/leds/common.h, so use the hardcoded string for them instead.
Fixes: 9d93b6d091 ("mvebu: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add pending patches to add LED_FUNCTION_MOBILE and LED_FUNCTION_SPEED_*
definitions for Fortinet FortiGate devices and IIJ SA-W2.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Specifications:
Qualcomm/Atheros QCA9531
2x 10/100 Mbps Ethernet, with 48v PoE
2T2R 2.4 GHz, 802.11b/g/n
128MB RAM
16MB SPI Flash
4x LED (Always On Power, LAN, WAN, WLAN)
Flashing instructions:
The original firmware is based on OpenWrt, so flashing the sysupgrade image over the factory firmware is sufficient.
The bootloader has a built-in recovery web-ui. This is the method I used to flash OpenWrt. You can get to the recovery web-ui by holding down the reset button for a few seconds (~5s) while pluggin in the router. The LEDs should start blinking fast and the router should be available on 192.168.1.1 for the recovery.
Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much to test), WLAN LED, MAC addresses (same as factory firmware).
Signed-off-by: Felix Golatofski <git@xdfr.de>
This reordering was done using these commands:
./scripts/kconfig.pl '+' target/linux/generic/config-6.1 /dev/null > target/linux/generic/config-6.1-new
mv target/linux/generic/config-6.1-new target/linux/generic/config-6.1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change the RGB indicator LED color for the running state from green to
blue. There are various reasons for this change:
- In stock firmware, green means internet connection is up, red means it
is down, and blue means indeterminate. To track stock behavior as
closely as possible, OpenWrt should indicate blue by default.
- In the current 23.x OpenWrt releases for this router, the led glows
blue all the time -not green- because the bootloader sets it blue
and there is an OpenWrt bug that makes it unable to control the LED.
The bug is fixed in master, so without this commit there would be an
unexpected change of behavior for this device in the next release.
- The ports other closely related Linksys devices (such as EA8300 and
MR8300) get this right and use blue for the running state.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
The RGB LED should glow green in the 'running' state, but it
was glowing cyan because the blue component defaulted to 'on'.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
The upstream solution to define the MDIO bus in DT is a bit
more strict than our previous downstream solution doing the same thing
and now requires switch PHYs to be referenced in DT as well.
Arınç Ünal told us in #15141:
"With [the now upstream patch written by him which we backported], the
switch MDIO bus won't be assigned to ds->user_mii_bus when the switch
MDIO bus is defined on the device tree anymore. This was not the case
with the downstream patch.
When ds->user_mii_bus is populated, DSA will 1:1 map the port with
PHY. Meaning port with address 1 will be mapped to PHY with address 1.
Because that ds->user_mii_bus is not populated when the switch MDIO
bus is defined on the device tree, on every port node, the PHY address
must be supplied by the phy-handle property."
Add those phy-handles to affected devices' DT.
Fixes: 4354b34f6f ("generic: 6.6: sync mt7530 DSA driver with upstream")
Fixes: 401a6ccfaf ("generic: 6.1: sync mt7530 DSA driver with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
TP-Link EC220-G5 v2 is a dual band router with 4 GbE ports
Advertised as AC1200 for its 867Mbps (2x2) 5GHz band
and 300 Mbps (2x2) 2.4GHz band.
Specs:
- SoC: MediaTek MT7620A
- Ethernet: 4x GbE ports (Realtek RTL8367S)
- Wireless 2.4GHz: MediaTek MT7620A
- Wireless 5GHz: MediaTek MT7612E
- RAM: 64MiB
- ROM: 8MiB (W25Q64BV)
- 2 Buttons (WPS and reset)
- 7 LEDs
Flash instructions via serial console:
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
tftp 0x80060000 test.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
Flash instructions via TFTP:
1. Update orginal firmware of the router to the latest one.
2. Rename openwrt-ramips-mt7620-tplink_ec220-g5-v2-squashfs-tftp-recovery.bin to tp_recovery.bin
3. Change computer IP to 192.168.0.66
4. Run TFTP serwer
5. Start the router with the reset button pressed, the file will be automatically downloaded and after a while the router will restart.
6. After updating, set your computer's IP to DHCP
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Change the name mt7620a_tplink_archer.dtsi to mt7620a_tplink_8m.dtsi because it will also be a base for TP-Link non-Archer routers.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
The function introduced in commit 7cbfe5654d is named
filter_port_list_reverse, not filter_port_list_reversed.
Fixes the following error on hpe,1920-8g-poe-65w and
hpe,1920-8g-poe-180w.
/bin/board_detect: /etc/board.d/02_network: line 84: filter_port_list_reversed: not found
Fixes: 7cbfe5654d ("realtek: move port filtering out of uci_set_poe()")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Sander Vanheule <sander@svanheule.net>
Fix also some Chinese GB18030 -> UTF-8 encoding problems
(translated the Chinese strings to English):
修改 -> modification
port8~port10的设置在另外一个register ->
port8~port10 setup is done in a separate register
You are in the correct (UTF-8) encoding when you see:
* $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
e.g. week 3, 08 third month, 2017
But not if you see:
* $Date: 2017-03-08 15:13:58 +0800 (閫变笁, 08 涓夋湀 2017) $
rtl8367c/rtl8367c_asicdrv_lut.c should be read as UTF-8, despite having
some earlier Chinese text lost to GB18030 encoding.
Improves indexing and searches
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
We have defaulted to 6.6 for a while so its time to completely drop 6.1
so new devices dont have to include patches for 6.1.
Signed-off-by: Robert Marko <robimarko@gmail.com>
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input
Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Airoha EN8801SC PHY is a gigabit PHY used on Edgecore EAP111 so, include
the MTK driver with some cleanups.
Unfortunatelly, there is no specification sheet nor datasheet available
in order to demistify the magic PBUS writes and work on upstreaming
this driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
First patch allows to inquire and modify Energy-Efficient-Ethernet
(EEE) settings via ethtool and thereby override the default setting of
a board done via bootstrap pins.
The second patch fixes a long-standing issue with STP (and similar
protocols) when using boards (or SoCs) governed by the mt7530 DSA
driver.
Both patches could also be (dirty-)applied to Linux 5.15, but I'd
rather just wait for that to happen via linux-stable to avoid the
mess.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport lots upstream changes, many of them fixes, for the mt7530 DSA
driver, similar to how it was done for Linux 6.1 in the previous commit.
The remaining differences compared to the upstream driver are only
the 'slave' -> 'user', 'master' -> 'conduit' language change in DSA
and the rename of 'struct ethtool_eee' to 'struct ethtool_keee' as
well as tree-wide replacement of ethtool_sprintf with ethtool_puts,
all of them do not have any functional impact.
Apart from some minor bug fixes and style improvements the switch
should now behave more conformant when it comes to link-local frames,
and we will again be able to cleanly pick patches from upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport lots upstream changes, many of them fixes, for the mt7530 DSA
driver. Some of them may or may not find they way into Linux 6.1
stable, some certainly won't because they are fixes for backported
commits which aren't even present in Linux 6.1 upstream.
Apart from adding new patches, also remove mutated patch
723-net-mt7531-ensure-all-MACs-are-powered-down-before-r.patch
which should never have been added for Linux 6.1 -- it was applied
already upstream but coincidentally would fuzzy-apply in the wrong
place as well (for MT7530 instead of MT7531). While that didn't really
hurt anyone it is just unneeded.
The other deleted patch
795-mt7530-register-OF-node-for-internal-MDIO-bus.patch
has been replaced by an equivalent commit with a more complete patch
description by upstream maintainer Arınç Ünal.
The remaining differences compared to the upstream driver are:
* C22/C45 MDIO ops aren't split
Upstream did that, backporting it would require making changes to
*all* DSA drivers
* 'slave' -> 'user', 'master' -> 'conduit' language change in DSA
* support for selecting preferred CPU port on MT7531
Also this would require too many DSA framework changes potentially
affecting other devices. If we ever really use Linux 6.1 in a
release (I hope not) we can still reconsider to make the effort to
backport that.
In addition to some minor bug fixes and style improvements the switch
should now behave more conformant when it comes to link-local frames,
and we will again be able to cleanly pick patches from upstream.
MAINTAIERS NOTE:
Three patches are already part of Linux stable and should be removed with
the next minor kernel version bump:
789-STABLE-01-net-dsa-mt7530-prevent-possible-incorrect-XTAL-frequ.patch
789-STABLE-02-net-dsa-mt7530-fix-link-local-frames-that-ingress-vl.patch
789-STABLE-03-net-dsa-mt7530-fix-handling-of-all-link-local-frames.patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure all patches can be applied to a git tree using 'git am'
by adding missing patch headers where needed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The sysupgrade formware of the Puzzle series is a slightly strange
dual-boot approach while remaining compatible with Marvell's SDK
firmware upgrade binary format -- which happens to be a full-disk
image with GPT partition table. Hence that /lib/upgrade/emmc-puzzle.sh
script is like an exotic disease which results from those decisions,
and as we also want to somehow stay compatible with the IEI-World
stock firmware we got to use it in that same way (we are not
compatible with the QNAP-branded identical hardware device anyway).
Currently, on sysupgrade the result is that one ends up with the old
content of rootfs_data (a GPT partition on those devices) as nothing
ever wipes or in any way re-creates the filesystem there. As a simple
work-around, let's kill the filesystem on rootfs_data so fstools
re-formats it on the next boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Trying to link certain kernel modules like dahdi-linux when building with
the OpenWrt SDK will fail with:
openwrt-sdk-apm821xx-sata_gcc-13.2.0_musl.Linux-x86_64/staging_dir/toolchain-powerpc_464fp_gcc-13.2.0_musl/bin/powerpc-openwrt-linux-musl-ld: cannot find arch/powerpc/lib/crtsavres.o: No such file or directory
Previously this worked with the PowerPC SDK since we carried a hack that
was passing --save-restore-funcs to module LDFLAGS so the linker provided
the required functions automatically as without --save-restore-funcs it
doesnt do so automatically on relocatable links and as a sideffect did not
require the kernel provided crtsaves.o to link against.
Now that hack has been removed as upstream kernel now compiles crtsaves.o
by default so it can be linked against but its not included in the SDK.
So, lets include lib/crtsavres.o when SDK is generated for PowerPC.
Fixes: 99c9d8abd6 ("kernel: bump 5.15 to 5.15.148")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently the compile phase of the kernel builds `Image dtbs modules`.
However, none of the dtbs that get built are used for the final image.
This ends up unnecessarily taking CPU cycles and produces a lot of
`WARNINGS` that can lead users to believe there's cause for concern. I
believe the same principle can be applied to other targets.
```
DTC arch/arm64/boot/dts/qcom/msm8996-mtp.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])
DTC arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])
DTC arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])
DTC arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])
DTC arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])
DTC arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])
DTC arch/arm64/boot/dts/qcom/msm8996-xiaomi-scorpio.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])
```
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Historically it's possible to leave the `SUBTARGETS` undefined and
automatically fallback to a "generic" subtarget. This however breaks
various downstream scripts which may have expectations around filenames:
While some targets with an explicit generic subtarget contain `generic`
in the filenames of artifacts, implicit "subtargets" don't.
Right now this breaks the CI[1], possibly also scripts using the ImageBuilders.
This commit removes all code that support implicit handling of
subtargets and instead requires every target to define "SUBTARGETS".
[1]: https://github.com/openwrt/openwrt/actions/runs/8592821105/job/23548273630
Signed-off-by: Paul Spooren <mail@aparcar.org>
Historically it's possible to leave the `SUBTARGETS` undefined and
automatically fallback to a "generic" subtarget. This however breaks
various downstream scripts which may have expectations around filenames:
While some targets with an explicit generic subtarget contain `generic`
in the filenames of artifacts, implicit "subtargets" don't.
Right now this breaks the CI[1], possibly also scripts using the ImageBuilders.
Do to the D1 target what's done to other target, explicitly define the
"generic" subtarget.
[1]: https://github.com/openwrt/openwrt/actions/runs/8592821105/job/23548273630
Signed-off-by: Paul Spooren <mail@aparcar.org>
This device is very similar to the GS1900-24E switch (added in b515ad1),
except that the first 12 of 24 ethernet ports are capable of PoE and the
physical jacks are in the right order - unlike for the GS1900-24E, where
even and uneven ports are flipped (up <-> down on panel).
Zyxel version code for this device (-24EP) is: ABTO
Signed-off-by: Mirko Vogt <mirko-openwrt@nanl.de>
Sync 6.1 patches with the RPi foundation.
Since rpi-6.6.y is now the main branch of the RPi foundation, there won't be
any new patches for linux 6.1.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Kernel 6.6 added dynamic SWIOTLB allocation, but with it also started
allocating 64MB of the SWIOTLB bounce buffer by default which is quite a
lot of memory on most OpenWrt devices.
Luckily in kernel 6.7 arm64 received an optimization that reduces that
default size to 1MB per 1GB of RAM if certain criteria was met.
So in order to reclaim back 63MB of RAM which brought some ipq807x devices
close to OOM under load lets backport the upstream commit.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add options removed by `make kernel_oldconfig CONFIG_TARGET=subtarget', missing which causes compilation to stop and cause an error.
Fixes: 2a86425de1 ("x86: 6.6: refresh kernel config")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Add:
110-pwm-img-fix-clock-lookup.patch
- patch to fix a clock lookup issue from upstream
Update:
401-mtd-nor-support-mtd-name-from-device-tree.patch
- mtd-name lookup hack to reflect the updated spi_nor_scan function
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
refreshed kernel config + patches
otherwise same as 6.1/5.15.
Tested on: WNDAP620, WNDAP660, MyBook Live Single, MR24, MX60, WNDR4700
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With the default BUILD_BOT configuration on a linux 6.6 kernel,
the WNDR4700's kernel no longer fits into the alloted ~3.5MiB,
even with LZMA compression.
Bigger kernels are possible, but there's a problem with Netgear's
"bootcmd":
> if loadn_dniimg 0 0x180000 0x4e0000 && chk_dniimg 0x4e0000; then nand read 0x800000 0x180000 0x20000;bootm 0x500000 - 0x800040;else fw_recovery; fi"
This loads the dni-image starting offset 0x180000 from the NAND
flash (which is the DTB partition) to 0x4e0000 in the RAM. It then
checks whenever the provided image is "valid". If it is then it
reads the DTB again to 0x800000 in the RAM and starts the extraction
and boot process. (If the image wasn't valid then it starts the
automated firmware recovery).
The issues here are that first: the kernel image gets "squeezed"
between 0x500040 and 0x7fffff... And second, the decompressor
only has area 0x0 - 0x500000 for decompression.
Hence the image now requires to update the bootcmd by providing
new values (which have been successfully tested with the original
Netgear WNDR4700 v1.0.0.56 firmware) for the RAM locations and
make full use of the fact that loadn_dniimg loads the DTB as well.
This needs to be done only once. Just connect a serial adapter to
interface with uboot and overwrite (and save) the new bootcmd.
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
Steps:
0. Power-off the WNDR4700
1. Connect the serial interface (you need to open the WNDR4700)
2. Power-up the WNDR4700
3. Monitor the boot-sequence and hit "Enter"-key when it says:
"Hit any key to stop autoboot" (Be quick, you have a ~2 second window)
4. in the Prompt enter the following commands (copy & paste)
setenv bootcmd "if loadn_dniimg 0 0x180000 0xce0000 && chk_dniimg 0xce0000; then bootm 0xd00000 - 0xce0040;else fw_recovery; fi"
saveenv
run bootcmd
Note: This new bootcmd will also unbrick devices that were bricked
by the bigger 4.19-6.1 kernels.
Note2: This method was tested with a WNDR4700. A big kernel with most
debug features enabled on v6.6.22 measured 4.30 MiB when compressed
with lzma. The uncompressed kernel is 12.34 MiB. This is over the 3 MiB,
the device reserves for the kernel... But it booted! For bigger kernels,
the device needs repartitioning of the the ubi partition due to the
kernel+dtb not fitting into the partition.
Note3: For initramfs development. I would advice to load the initramfs
images to 0x800000 (or higher). i.e.: tftp 800000 wndr4700.bin
Note4: the fw_recovery uboot command to transfer the factory image to
the flash still works.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Compatiblity with kernel 6.6 for Awinic AW9523B i2c pin controller driver.
It follows the kernel patch: i2c: Drop legacy callback .probe_new() (5eb1e6e459)
and kernel patch: gpiolib: Get rid of not used of_node member (70d0fc4288)
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Fix error: 'struct snd_soc_dai_driver' has no member named 'remove'
It follows the kernel patch: ASoC: soc-dai.h: remove unused call back functions (446b31e894)
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
With 6.6, all DTSes were moved to their vendor subdirectories. ARM64
DTSes already used this scheme, but 32 bit Cortex A9 did not, prior
to 6.6. Introduce a kernel version check to keep backward compatibility
with 6.1.
Suggested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
As of 6.6, all upstream DTSes are moved to their respective vendor subdir.
OpenWrt already followed this practice for ARM64, but not yet for 32 bit
ARM (Armada 37x/38x).
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
DTS paths for 32 bit ARM devices changed with 6.6, move files/ to
files-6.1 to prep for kernel 6.6 introduction.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Add pending patch fixing nandc with new kerenel due to broken convertion
to new nand API. Patch has been sent upstream and will be backported to
stable kernel if accepted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework kernel patches for new kernel. Mainly adaptation for patch
related to DTS and changes for the downstream div generalize patch that
now use determine_rate.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since with recent kernel version DTS moved to a dedicated directory,
it's required to split files to per kernel version to follow kernel
version directory structure.
Also makes use of DEVICE_DTS_DIR to target the correct DTS directory
based on the kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch fixing mtdcore with MTD OTP with a fragile detection
if Nand supports OTP. Patch has been sent upstream and will be backported
to stable kernel if accepted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework kernel patches for new kernel. Mainly adaptation for patch
related to DTS, OOB Tagger and SDHCI patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS to use reference for usb node instead of redefining
them since upstream usb node names changed from usb2/3 to usb.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since with recent kernel version DTS moved to a dedicated directory,
it's required to split files to per kernel version to follow kernel
version directory structure.
Also makes use of DEVICE_DTS_DIR to target the correct DTS directory
based on the kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh backport patches for kernel 6.1.82 with make target/linux/refresh.
Fixes: 06cdc07f8c ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 3 buttons (WPS, reset, LED on/off)
- 1 1Gbit WAN port
- 4 1Gbit LAN ports
Disassembly:
- There are four screws at the bottom: 2 under the rubber feets, 2 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes on the side of the board.
- Pins (from front to rear):
- 3.3V
- RX
- TX
- GND
- Settings: 115200, 8N1
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- The recovery web interface always flashes to the currently active partition.
- If OpenWrt is flahsed to the second partition, it will not boot.
- Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end.
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-recovery.bin
- The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt.
- If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are reuqired:
- Start the web recovery interface again and flash the **decrypted OEM image**. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1.
- Now flash the **encrypted OEM image** via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1.
- Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-initramfs-kernel.bin.
- Power on the device and select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.200.2, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M30 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware M30A1_FW101B05: ./m32-firmware-util M30 --DecryptFactoryImage M30A1_FW101B05\(0725091522\).bin M30A1_FW101B05\(0725091522\)_decrypted.bin
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Controlling the LEDs:
- The LEDs are controlled by a chip called "GCA230718" which is connected to the main CPU via I2C (address 0x40)
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Comparison to M32/R32:
- The algorithms for decrypting the OEM firmware are the same for M30/M32/R32, only the keys differ
- The keys are available in the GPL sources for the M32
- The M32/R32 contained raw data in the firmware images (kernel, rootfs), the R30 uses a sysupgrade tar instead
- Creation of the recovery image is quite similar, only the header start string changes. So mostly takeover from M32/R32 for that.
- Turned out that the bytes at offset 0x0E and 0x0F in the recovery image header are the checksum over the data area
- This checksum was not checked in the recovery web interface of M32/R32 devices, but is now active in R30
- I adapted the recovery image creation to also calculate the checksum over the data area
- The recovery image header for M30 contains addresses which don't match the memory layout in the DTS. The same addresses are also present in the OEM images
- The recovery web interface either calculates the correct addresses from it or has it's own logic to determine where which information must be written
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
The recovery image is reqired for D-Link M30 as well. So I moved it to include/image-commands.mk to be able to use it for MT7622 and filogic devices.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO
enterprise access point with two Gigabit Ethernet ports and PoE
support.
Hardware highlights:
- CPU: QCA9550 SoC at 720MHz
- RAM: 256MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: QCA9550-internal radio
- Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC
- Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY
- Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY
- PoE: input through Ethernet 1 port
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: SGM706 (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- eth1 = label MAC + 1
- radio0 (Wi-Fi 5GHz) = label MAC + 2
- radio1 (Wi-Fi 2.4GHz) = label MAC + 3
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script
"run ramboot". Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile
openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot
be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from
non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP5X30XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap5030dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues
-----------------------
- On initial power-up, the Huawei-modified bootloader suspends both
ethernet PHYs (it sets the "Power Down" bit in the MII control
register). Unfortunately, at the time of the initial port, the kernel
driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume
callback defined which would clear this bit. This makes the PHY unusable
since it remains suspended forever. This is why the backported kernel
patches in this commit are required which add this callback and for
completeness also a suspend callback.
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the CPU_CLK/4 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
[fixed 6.6 backport patch naming]
Signed-off-by: David Bauer <mail@david-bauer.net>
On x86, the build failed while trying to compile tools/lib/string.c because
of a clash with the system provided implementation for strlcpy
Add ifdefs to prevent the conflict.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This device only has 64 MiB RAM and ath10k wireless driver will
consume a lot of memory. Let's move it to the tiny sub-target to
get extra 7 MiB of free space. In this way, we can extend their
lifetime to receive support for the next OpenWrt LTS version. This
patch also trims the duplicate "recovery.bin" image as it's the
same as the "factory.bin".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
These devices only have 64 MiB RAM and ath10k wireless driver will
consume a lot of memory. Let's move them to the tiny sub-target to
get extra 7 MiB of free space. In this way, we can extend their
lifetime to receive support for the next OpenWrt LTS version. This
patch also trims the USB package for the non-existent USB port.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The upcoming D-Link devices to the tiny sub-target require it to
parse the u-env MAC address. The kernel size will increase by
about 1 KiB.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Move seama image recipe to the common Makefile in order for some
tiny sub-target D-Link devices can share it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: W632GU6NB DDR3 256MB
Ethernet: 1x 2.5G + 4x 1G
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
1. Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
2. Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-preloader.bin spi0.0"
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
3. Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download initramfs image, reboot router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Note:
1. Back up all mtd partitions before flashing.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The image generation would fail, if the target is included from a feed.
To fix this, check if targets is found in the feed directory.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Fixes the regression so that targets that were installed via a feed can
also be build again with the Image Builder.
Fixes: 84ec8c4 ("imagebuilder: copy from buildroot only target/linux")
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
ttyS2 is the default console used for all rockchip boards.
The redundant 'console=tty1' parameter now breaks the console due to
recent procd update.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: e35c7ab51f ("rockchip: merge bootscript")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
6.6 has been in testing on qualcommax for a while so it should be in a
good shape, but lets default to it to get a wider audience.
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's required to support NAND controllers with WP pin on boards that
don't have it connected to NAND chip.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Key features:
Allwinner H618 SoC (Quad core Cortex-A53)
1/1.5/2/4 GiB LPDDR4 DRAM
1 USB 2.0 type C port (Power + OTG)
1 USB 2.0 host port
1Gbps Ethernet port
Micro-HDMI port
MicroSD slot
Installation:
Write the image to SD Card with dd.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Backport AXP15060, AXP313a and AXP192 support.
The AXP15060 PMIC is used for starfive boards,
and the AXP313a PMIC is used for sunxi boards.
Remove conflicting patches from starfive target.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix issue of transmitting abnormal data which leads to link problems
in 1G and 2.5G SerDes modes (SGMII, 1000Base-X, 2500Base-X) on the
MediaTek MT7988 SoC.
Link: b72d6cba92
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Zyxel GS1900-8 v2 or Rev.B1 is a newer variant of the GS1900-8, but
otherwise similar to the other GS1900 switches.
Differences
------------
* Front Button labeled RESTORE
* NO Power Switch on rear
* Serial Header next to the barrel power connector
* Part Number ends 0102F
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 8GB eMMC or 128 MB SPI-NAND
RAM: 256MB
Ethernet: 5x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
USB: M.2(B-key) for 4G/5G Module
Power: DC 12V 1A
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC RX TX GND | <= |
| ----------------- |
--------------------------
The U-boot menu will automatically appear at startup, and then select
the required options through UP/DOWN Key.
NAND Flash and eMMC Flash instructions:
1. Set your computers IP adress to 192.168.1.2.
2. Run a TFTP server providing the sysupgrade.bin image.
3. Power on the router, into the U-Boot menu.
4. Select "2. Upgrade firmware"
5. Update sysupgrade.bin file name, input server IP and input device
IP (if they deviate from the defaults)
6. Wait for automatic startup after burning
Signed-off-by: Allen Zhao <allenzhao@unielecinc.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
patch 150-arch-powerpc-simpleboot-prevent-overwrite-of-CPU1-sp.patch
was missed durring copy from 5.15 to 6.1.
This patch restore it.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Add support for Gateworks Venice imx8m family of boards:
- required kernel modules for on-board devices
- image generation
- initial network config
- sysupgrade support
The resulting compressed disk image
(bin/targets/imx/cortexa53/openwrt-imx-cortexa53-gateworks_venice-squashfs-img.gz)
can be installed on a Gateworks venice board via U-Boot:
u-boot=> tftpboot $loadaddr openwrt-imx-cortexa53-gateworks_venice-squashfs-img.gz && \
gzwrite mmc $dev $loadaddr $filesize
WARNING: this will overwrite any boot firmware on the eMMC user hardware
partition which if being used will brick your board requiring JTAG to
re-program boot firmware and recover
The compressed disk image contains the partition table and filesystems only
and that it is expected that boot firmware is installed properly on the
eMMC boot0 hardware partition. The easiest way to ensure this is to
use the Gateworks JTAG adapter/process to install the latest boot firmware
as follows from a Linux host:
wget http://dev.gateworks.com/jtag/jtag_usbv4
chmod +x jtag_usbv4
wget http://dev.gateworks.com/venice/images/firmware-venice-imx8mm.bin
sudo ./jtag_usbv4 -p firmware-venice-imx8mm.bin
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add imx8m support:
- add a cortexa53 subtarget to imx
- move ARCH and KERNELNAME to subtargets
- account for kernel modules that are not used for cortexa53
No device-specific targets or firmware images are created yet but all
imx8m* dtbs will be built.
enabling CONFIG_TARGET_ROOTFS_INITRAMFS results in
openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin which has been
successfully booted on an imx8mm-evk using the following:
u-boot=> tftpboot $fdt_addr_r image-imx8mm-evk.dtb && \
tftpboot $kernel_addr_r openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin && \
booti $kernel_addr_r - $fdt_addr_r
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a hotplug script and add ttyATH1 on ELECOM WAB-I1750-PS to
/etc/inittab while booting for using that console as an OpenWrt console.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Register ttyS0 and ttyATH1 as Linux console on ELECOM WAB-I1750-PS.
ttyS0 provides "SERVICE" port and internal pin header for debugging and
recoverying by maker, ttyATH1 provides "SERIAL" port for configuration
by users.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The 6.1 kernel has caused another increase in kernel size, and now
it's more than 3MB:
WARNING: Image file iom_ix4-200d-uImage is too big: 3170394 > 3145728
WARNING: Image file iom_ix2-200-uImage is too big: 3171494 > 3145728
WARNING: Image file linksys_e4200-v2-uImage is too big: 3171879 > 3145728
WARNING: Image file linksys_ea4500-uImage is too big: 3171871 > 3145728
WARNING: Image file linksys_ea3500-uImage is too big: 3171651 > 3145728
This causes problems for 5 devices:
- Iomega StorCenter ix2/ix4
- Linksys EA3500/EA4200/EA4500
They have enough resources for proper operation with 6.1, but all of
them had a 3MB kernel size limit. Let's keep them alive and
resize kernel partitions to 4MB.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
6.1 testing version was introduced some time ago. Kernel size issues
are resolved now. Time to bump kernel version.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
When build images with the 6.1 kernel for all devices and all kmods,
there is one dependancy error:
pkg_hash_check_unresolved: cannot find dependency kmod-thermal
for kmod-hwmon-gpiofan
This commit fix that issue.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Copied from original Andrew's Lunn commit message:
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Kirkwood Ethernet is an RGMII port. Set the
switch to impose the RGMII delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
This commit backport change from upstream and fix downstream EA3500 dts.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
TP-Link RE205 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with external antennas.
It's based on MediaTek MT7628AN+MT7610EN like the RE200 v3/v4 but with
external antennas.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 5x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)
There are 2.4G and 5G LEDs in blue which are controlled separately.
Installation
------------
Installation is identical to RE200 v3 devices as described at
https://openwrt.org/toh/tp-link/re200#installation
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
U-Boot seems to be locked on newer versions, if not it can be accessed over
the UART as described in the link above.
Signed-off-by: Steffen Loley <slo-src@web.de>
This service was unfunctional due to not having its executable bit set.
Furthermore, sysupgrade complains about the file being present in images.
Also, the tc654 driver doesn't provide pwm1_enable sysfs file, instead its
now called pwm1_mode.
Please note that the fan was always spinning. It should now turn off, when
there's enough the thermal headroom.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
D-Link DGS-1210-16 hangs when rebooting and has no support for the reset
button.
Fix both by enabling the same GPIOs for reboot and the reset button as
already used for D-Link DGS-1210-20 and D-Link DGS-1210-28.
Signed-off-by: Richard Kunze <kunze@tivano.de>
When rebasing patches on top of 6.1, a change that removed NF_TABLES
from NF_FLOW_TABLE's dependency was dropped accidentally, and iptables
flow offload module can only be built when nftables is selected.
Restore the change to fix it.
Fixes: 19a246bb65 ("generic: 6.1: manually refresh hack patches")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Installation:
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Kernel 6.6 has changed the path of WLAN devices as the soc node was updated
to include an adress as well because according to spec it needed one:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v6.6.21&id=da6aa1111a17db11367817ddc10c5a6c188cdc44
So, this will break existing configuration as device path was changed for
example:
"platform/soc/c000000.wifi" to "platform/soc@0/c000000.wifi"
"platform/soc/c000000.wifi+1" to "platform/soc@0/c000000.wifi+1"
PCIe attached devices also have their path changed, so lets add a script
that will migrate the paths based on the detected running kernel version
so returning to kernel 6.1 will work as well.
Co-developed-by: Sean Khan <datapronix@protonmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When building MT7629 with ALL_KMODS then we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot compilation.
It depends on I2C so the symbol is hidden until ALL_KMODS is used and I2C
support is available, so disable the LEDS_SMARTRG_LED symbol in 6.6 config
intentionally as is done in the 6.1 mt7629 config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Disable CONFIG_CRYPTO_SM4_ARM64_CE_CCM and CONFIG_CRYPTO_SM4_ARM64_CE_GCM
in the generic config like we do with similar CE symbols.
This avoids the need to disable them in individual targets.
Signed-off-by: Robert Marko <robimarko@gmail.com>
* have more defined PWM steps similar to the vendor's shell script doing
the same thing
* replace PWM values with experiencal values provided by forum users
* increase hyteresis to prevent changing fan speed every second
(just because it's annoying to listen to)
* add 'hot' trip point at 75 deg. to warn users that shutdown is imminent
Tested on Puzzle M902 only for now, PWM values for Puzzle M901 might be
slightly different but should quite certainly also be rised.
Suggested-by: Martin Gierschner <martin_gierschner@gmx.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The vendor u-boot knows nothing about UBI, and we used to have a
fixed-size kernel partition for vendor u-boot and UBI for rootfs.
However, that fixed partition becomes too small eventually, and
expanding it requires complicated procedure.
This commit changed the flash layout and added a second u-boot
where the kernel supposed to be.
Now the vendor u-boot chainloads our mainline u-boot, and our
u-boot reads kernel+rootfs from UBI, verifies it, and boot
into OpenWrt.
There are two possible ways to convert from the old fw:
Flash the factory image using mtd (provided by @rany2):
mount -o remount,ro /
mount -o remount,ro /overlay
cd /tmp
dd if=factory.bin bs=1M count=4 | mtd write - kernel
dd if=factory.bin bs=1M skip=4 | mtd -r write - ubi
Or, flash the 2nd u-boot via mtd and upload the firmware
to the 2nd u-boot using tftp:
1. prepare a tftp server at 192.168.1.254 to serve the
sysupgrade image:
openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-squashfs-sysupgrade.itb
2. upload the ubi-loader.itb to OpenWrt /tmp, and flash it to
the old kernel partition:
mtd -r write openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-ubi-loader.itb
3. The router should reboot and flash the sysupgrade image via TFTP.
Procedure for flashing from vendor firmware shouldn't change.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
With kernel 6.1 image size is too large for Edgerouter X current size
limit and is causing the buildbots to fail building so images for other
devices are not updated as well.
So, disable building Edgerouter X images until a workaround is found.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit e298d8a38b23 [0] changed method how to blink delays are pased
to function. Downstream commit must follow it.
[0] https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Currently, 6 MAC addresses are read from the "boarddata1" partition and set for network interfaces in sequence.
This partition only contains 3 MAC addresses:
1. lan mac
2. wan mac
3. wlan5g mac
As result only lan2, lan3 and lan4 have correct (OUI) MAC addresses.
lan1, lan5 and wan interfaces get MAC addresses with incorrect OUI from random data on "boarddata1" partition.
This commit fix this and use first MAC for lan and second MAC for wan interfaces.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
The port 5 of most ipq60xx devices is connected to qca8075,
a few are connected to qca8081. So assume that the default
connection is qca8075 and set the phy mode to psgmii.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Marvell's thermal sensors do not support interrupts, so we need to
poll them. Reading temperature every second should be enough to
control the fan.
While at it, also make sure fan speed is reduced again if temperature
goes down.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On Buffalo WXR-5590AX12, some LEDs don't have "function" property and
only "color" property is available for the newer binding of LED on
Linux Kernel.
2e659930d3 ("qualcommax: drop redundant label with new LED
color/function format") removes "label" property from LEDs, then,
multiple "<color>:" (ex.: "white:"/"red:") will be appeared as LED names
and renamed to "<color>:_<num>" ("ex.: "white:_1", "green:_2", ...) by
kernel.
logs:
[ 5.372863] leds-gpio leds: Led white: renamed to white:_1 due to name collision
[ 5.375796] leds-gpio leds: Led red: renamed to red:_1 due to name collision
/sys/class/leds:
root@OpenWrt:/# ls /sys/class/leds/
red: red:power white: white:power
red:_1 red:wlan white:_1 white:wlan
Fix this issue by adding missing "function" property to LEDs on Buffalo
WXR-5950AX12.
Note: there are no appropriate functions in dt-bindings/leds/common.h
for some LEDs, so use the hardcoded strings for them instead.
Fixes: 2e659930d3 ("qualcommax: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
On QNAP QHora-301W, all LEDs don't have "function" property and only
"color" property is available for the newer binding of LED on Linux
Kernel.
2e659930d3 ("qualcommax: drop redundant label with new LED
color/function format") removes "label" property from LEDs, then,
multiple "<color>:" (ex.: "amber:"/"green:"/"red:") will be appeared as
LED names and renamed to "<color>:_<num>" ("ex.: "green:_1", "green:_2",
...) by kernel.
logs:
[ 4.246494] leds-gpio leds: Led green: renamed to green:_1 due to name collision
[ 4.248978] leds-gpio leds: Led green: renamed to green:_2 due to name collision
[ 4.256345] leds-gpio leds: Led green: renamed to green:_3 due to name collision
[ 4.263770] leds-gpio leds: Led green: renamed to green:_4 due to name collision
[ 4.271105] leds-gpio leds: Led amber: renamed to amber:_1 due to name collision
[ 4.278487] leds-gpio leds: Led green: renamed to green:_5 due to name collision
[ 4.285856] leds-gpio leds: Led amber: renamed to amber:_2 due to name collision
[ 4.293257] leds-gpio leds: Led green: renamed to green:_6 due to name collision
[ 4.300616] leds-gpio leds: Led amber: renamed to amber:_3 due to name collision
[ 4.308002] leds-gpio leds: Led green: renamed to green:_7 due to name collision
[ 4.315384] leds-gpio leds: Led amber: renamed to amber:_4 due to name collision
[ 4.322760] leds-gpio leds: Led green: renamed to green:_8 due to name collision
[ 4.330135] leds-gpio leds: Led amber: renamed to amber:_5 due to name collision
/sys/class/leds:
amber: amber:_4 green:_2 green:_6
amber:_1 green:_5 green:_3 green:_7
amber:_2 green: green:_4 green:_8
amber:_3 green:_1 green:_5 red:
Fix this issue by adding missing "function" (and "function-enumerator")
property to LEDs on QNAP QHora-301W.
Note: there are no appropriate functions in dt-bindings/leds/common.h
for some LEDs, so use the hardcoded strings for them instead.
Fixes: 2e659930d3 ("qualcommax: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is needed recommended.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6281 @1GHz
- 128Mb RAM
- 256Mb NAND
- 1x GbE LAN (Marvell 88E1116)
- 1x USB 2.0
- 2x SATA
- PCF8563 RTC
- LM75 sensor
- TC654 PWM fan controller
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b ./u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 netgear_stora-u-boot.kwb
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-netgear_stora-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
The fan is controlled in 3 stages by a script running every minute
from cron, measuring the CPU temperature.
Snippets taken from bodhi <mibodhi@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The dir variable has been used uninitialized since the port to 5.10, and
somehow this remains undetected by GCC.
Fixes: b10d604459 ("kernel: add linux 5.10 support")
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Most mt7622 devices use the mt7531 switch, which have been
switched to dsa driver for a long time. So use dsa as the
default configuration and configure these rtl8367s devices
separately. This reduces the amount of code.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
In kernel 6.6, dts files for mediatek arm target are moved into
arch/arm/boot/dts/mediatek instead of legacy path arch/arm/boot/dts.
To avoid dts compile failure, change DTS_DIR to the mediatek subfolder
for kernel 6.6.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Also backport most recent MHI modem additions to Linux 6.6.
Adds support for generic SDX75-based modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing CLK_TOP_PEXTP_Px_SEL clock for each of the 4 PCIe interfaces
of the MT7988 SoC. Without that clock PCIe doesn't work reliable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CONFIG_NET_VENDOR_DAVICOM is needed to activate the CONFIG_DM9000 option
which builds the kmod-dm9000. This fixes the following warning:
logs/package/kernel/linux/compile.txt:WARNING: kmod-dm9000 is not available in the kernel config - generating empty package
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Many can kernel modules are now gated by the newly introduced
CONFIG_CAN_NETLINK configuration option. Activate it to build the can
drivers again.
This was changed in this upstream Linux commit:
https://git.kernel.org/linus/df6ad5dd838e0fa543ca28ca6154901fa65a9443
This should fix these warnings with kernel 6.1 and 6.6:
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can-pci is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can-platform is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-mcp251x is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-slcan is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-8dev is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-ems is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-kvaser is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-peak is not available in the kernel config - generating empty package
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove the remaining configuration entries that were omitted in the
previous commit.
Fixes: 1576474f55 ("ramips: switch to 6.1 kernel")
Signed-off-by: Nick Hainke <vincent@systemli.org>
The GL.iNet X3000 and XE3000 are Wi-Fi 6 5G cellular routers, based on
MediaTek MT7981A SoC. The XE3000 is the same device as the X3000,
except for an additional battery.
Specifications:
- SoC: Filogic 820 MT7981A (1.3GHz)
- RAM: DDR4 512M
- Flash: eMMC 8G, MicroSD card slot
- WiFi: 2.4GHz and 5GHz with 6 antennas
- Ethernet:
- 1x LAN (10/100/1000M)
- 1x WAN (10/100/1000/2500M)
- 5G: Quectel RM520N-GL with two nano-SIM card slots
- USB: 1x USB 2.0 port
- UART:
- 3.3V, TX, RX, GND / 115200 8N1
MAC addresses as verified by OEM firmware:
vendor OpenWrt address source
WAN eth0 label factory 0x0a (label)
LAN eth1 label + 1
2g phy0-ap0 label + 2 factory 0x04
5g phy1-ap0 label + 3
Installation via U-Boot rescue:
1. Press and hold reset button while booting the device
2. Wait for the Internet led to blink 5 times
3. Release reset button
4. The rescue page is accessible via http://192.168.1.1
5. Select the OpenWrt sysupgrade image and start upgrade
6. Wait for the router to flash new firmware and reboot
Revert to stock firmware:
1. Download the stock firmware from GL.iNet website
2. Use the method explained above to flash the stock firmware
Switch the modem network port between PCIe and USB interfaces:
1. Connect to the AT commands (/dev/ttyUSB2) port using
e.g. minicom: minicom -D /dev/ttyUSB2
2. Check the current modem mode with 'AT+QCFG="data_interface"':
- 0,0 indicates that the network port uses the USB interface
- 1,0 indicates that the network port uses the PCIe interface
3. Switch the active interface with:
- 'AT+QCFG="data_interface",0,0' to use the USB interface
- 'AT+QCFG="data_interface",1,0' to use the PCIe interface
4. Reboot
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Add new emmc groups in the pinctrl driver for the
MediaTek MT7981 SoC:
* emmc reset, with pin 15.
* emmc 4-bit bus-width, with pins 16 to 19, and 24 to 25.
* emmc 8-bit bus-width, with pins 16 to 25.
The existing emmc_45 group is kept for legacy reasons, even
if this is the union of emmc_reset and emmc_8 groups.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Reference: b40da332df
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport commit faa5f17fe2 ("kernel: mtk_eth_soc: release
MAC_MCR_FORCE_LINK only when MAC is up") to Linux 5.15 as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The 5.15 kenel config file, patches and version switches will be
removed in this patch. We will introduce kernel 6.6 support soon.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This commit adds support for Z-ROUTER ZR-2660 (also known as Routerich
AX1800) wireless WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (AMD/Spansion S34ML01G2)
- WLAN :
- 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2
- 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- USB : 1x 2.0
- UART : 3.3V, 115200n8, pins are silkscreened on the pcb
- Buttons : 1x Reset
- LEDs : 1x WiFi 2.4 GHz (green)
1x WiFi 5 GHz (green)
1x LAN (green)
1x WAN (green)
1x WAN no-internet (red)
- Power : 12 VDC, 1 A
Installation
------------
1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs
image (initramfs.bin) to the tftp root dir
2. Open the following link in the browser to enable telnet:
http://192.168.2.1/cgi-bin/telnet_ssh
3. Connect to the router (default IP: 192.168.2.1) using telnet shell
(credentials - user:admin)
4. Run the following commands in the telnet shell (this will install
OpenWrt initramfs image on nand flash):
cd /tmp
tftp -g -r initramfs.bin 192.168.2.2
mtd write initramfs.bin firmware
mtd erase firmware_backup
reboot
5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the
router
6. Connect to the router (IP: 192.168.1.1) using ssh shell and run
sysupgrade command:
sysupgrade -n /tmp/sysupgrade.bin
Return to stock
---------------
1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp
2. Run following command in the router shell:
cd /tmp
mtd write stock.bin firmware
reboot
Recovery
--------
Connect uart (pins are silkscreened on the pcb), interrupt boot process by
pressing any key, use u-boot menu to flash stock firmware image or OpenWrt
initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 24:0f:5e:xx:xx:4c | label |
| WAN | 24:0f:5e:xx:xx:4d | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 |
+---------+-------------------+-----------+
The WLAN 2.4 MAC was found in 'factory', 0x4
The LAN MAC was found in 'factory', 0xfff4
The WAN MAC was found in 'factory', 0xfffa
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
When kernel 6.6 is being compiled with GCC13 it will prompt for:
Compressed Debug information
> 1. Don't compress debug information (DEBUG_INFO_COMPRESSED_NONE)
2. Compress debugging information with zlib (DEBUG_INFO_COMPRESSED_ZLIB)
3. Compress debugging information with zstd (DEBUG_INFO_COMPRESSED_ZSTD) (NEW)
This is because kernel now also has support for compressing debug info
with ZSTD, so add the missing symbol and disable it by default.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The YunCore G720 is a dual band 802.11ax router with 5 GbE ports.
Specs:
- SoC: MediaTek MT7621
- Ethernet: 5x GbE ports (built-in MT7530)
- Wireless 2.4GHz / 5GHz: MediaTek MT7915E
- RAM: 256MiB
- ROM: 16MiB (W25Q128)
- 1 Button (reset)
- 8 LEDs (1x system, 2x wifi, 5x switch ports)
Flash instructions:
The vendor firmware is based on OpenWrt, the sysupgrade image can be
flashed using the '-F' (force) option on the CLI.
Make sure not to keep settings when doing so.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
We have had the testing kernel for several weeks now. Let's switch to 6.1
to have more testers. Additionally, 6.6 is already in the pipeline.
Signed-off-by: Nick Hainke <vincent@systemli.org>
CONFIG_HID_SUPPORT:
Set default value for kmod-hid
CONFIG_USB_CDNS3_IMX:
CONFIG_USB_CDNS3_PCI_WRAP:
CONFIG_USB_CDNSP_PCI:
Introduced by db0d7cf6a1 (usb: add cdns3 support)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This reverts commit 7ea82bc17d.
This commit does not meet formal requirments, and has been merged due to
my error.
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_DEBUG_INFO_COMPRESSED_ZSTD, required by GCC 13.0+
Compress the debug information using zstd. This may provide better compression than zlib, for about the same time costs, but requires newer toolchain support. Requires GCC 13.0+ or Clang 16.0+, binutils 2.40+, and zstd.
Signed-off-by: CharlesMengCA <58993776+CharlesMengCA@users.noreply.github.com>
As shared remove functions now returns void instead of int we need to
use .remove_new instead of .remove.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A new patch was added meanwhile which will go as fix via netdev tree.
Copy & refresh it for Linux 6.6 as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Avoid crashing the kernel when trying to detect early versions of
RealTek RTL8221B 2.5G Ethernet PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, the existing uncompressed kallsym support is causing qualcommax
boards to hang on boot, and only after earlycon and verbose BUG() prints
are enabled the trace is visible:
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] kernel BUG at kernel/kallsyms.c:340!
[ 0.000000] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
Felix has fixed up the uncompressed kallsyms support so modify the current
patch with the fix.
All credits for the code go to Felix.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update fitblk driver which has previously been backported to Linux 6.1
so it can build and work with Linux 6.6.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing symbols to config for 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Due to what seems to be an undocumented oddity in MediaTek's MT7988
SoC design the CLK_INFRA_PCIE_PERI_26M_CK_P2 clock requires
CLK_INFRA_PCIE_PERI_26M_CK_P3 to be enabled.
This currently leads to PCIe port 2 not working in Linux.
Reflect the apparent relationship in the clk driver to make sure PCIe
port 2 of the MT7988 SoC works.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Clearing bit MAC_MCR_FORCE_LINK which forces the link down too early
can result in MAC ending up in a broken/blocked state.
Fix this by handling this bit in the .mac_link_up and .mac_link_down
calls instead of in .mac_finish.
Suggested-by: Mason-cw Chang <Mason-cw.Chang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 16MB SPI NOR W25Q128WFG
- RAM: 128MB DDR3 W631GG6KB-15
- Ethernet: 1x 1000M, 3x 100M
- Wifi: BCM435F
- 1x USB 2.0 port
- 3x Button
- 12x LED
Flashing via serial
- Connect to the 3.3V TTL UART on the board
(J6 pinout Vcc Rx Tx Gnd) at 115200-8-N-1
- Press any key in the serial console when powering up the board to enter
the CFE prompt
- Configure an interface on your workstation to static IP 192.168.1.100
and connect it to the board
- Start a TFTP server with the firmware image
- On the CFE prompt, enter the command
"f 192.168.1.100:openwrt-bmips-bcm63268-smartrg_sr505n-squashfs-cfe.bin"
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Remove unneeded LED labels]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
CDNS3 is a SuperSpeed (SS) USB 3.0 Dual-Role-Device (DRD) controller from
Cadence. Add support for this device, and add the required symbols into
the generic configs.
Compile-tested: apm821xx, bcm4908, imx, mpc85xx, pistachio, starfive
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* Increase flash SPI frequency to 50MHz
The maximum SPI frequency of MX25L6406EM2I is 86 MHz,
but in this patch 50 MHz was chosen as a safe value.
* Update Ethernet MAC addresses
Till now LAN/WAN MAC addresses were flipped
compared to stock firmware.
* Fix Wi-Fi LEDs by adding mt76 led nodes
* Fix LAN port order
LAN ports are in reverse order of switch ports.
* Fix the well-known "LZMA ERROR 1" error by using lzma-loader
* Set uImage name, which enables installation via stock web interface:
1. Upload **initramfs** image file to the web page.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Unlike the recovery image, this initramfs-factory image can be flashed
using the stock firmware web interface (from any active boot partition),
as well as the bootloader recovery web page. Drop the recovery image in
favor of the factory image.
Installation via stock/recovery web interface:
1. Flash **initramfs-factory** image through the web page.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The "0x80001000" address logically comes from "loadaddr-y" variable for
mt7621 subtarget. Let's replace the hardcoded value with the predefined
variable. This change is purely cosmetic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Contrary to common ipTIME NOR devices, the "Config" partition of T5004
and AX2004M contain normal U-Boot environment variables. Renaming the
partition into "u-boot-env" serves for better description, and it also
conforms to common naming practice in OpenWrt.
This patch might also be extended to A3004T, but its u-boot-env
partition layout has not been confirmed yet.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
AX2004M uses NMBM on its NAND flash, but it was not enabled in DTS as the
device support [1] had been added before NMBM feature in mtk_bmt driver [2].
Let's enable it now.
With this change, there is a low possibility of boot failure after
sysupgrade from older versions. As AX2004M already has gone through
two stable releases in the meantime, it would be safe to warn users
by bumping DEVICE_COMPAT_VERSION.
[1] 37753f34ac ("ramips: add support for ipTIME AX2004M")
[2] 06382d1af7 ("kernel: add support for mediatek NMBM flash mapping support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The COVR-C1200 devices are sold as "Whole Home Mesh Wi-Fi"
sets in packs of two (COVR-C1202) and three (COVR-C1203).
Specifications:
* QCA9563, 16 MiB flash, 128 MiB RAM, 2x3:2 802.11n
* QCA9886 2x2:2 801.11ac Wave 2
* AR8337, 2 Gigabit ports (1: WAN; 2: LAN)
* USB Type-C power connector (5V, 3A)
Installation COVR Point A:
* In factory reset state: OEM Web UI is at 192.168.0.50
no DHCP, skip wizard by directly accessing:
http://192.168.0.50/UpdateFirmware_Simple.html
* After completing setup wizard: Web UI is at 192.168.0.1
DHCP enabled, login with empty password
* Flash factory.bin
* Perform a factory reset to restore OpenWrt UCI defaults
Installation COVR Points B:
* OEM Web UI is at 192.168.0.50, no DHCP, empty password
* Flash factory.bin
* Perform a factory reset to restore OpenWrt UCI defaults
Recovery:
* Keep reset button pressed during power on
* Recovery Web UI is at 192.168.0.50, no DHCP
* Flash factory.bin
used to work best with Chromium-based browsers or curl:
curl -F firmware=@factory.bin \
http://192.168.0.50/upgrade.cgi
since this fails to work on modern Linux systems,
there is also a script dlink_recovery_upload.py
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Include a statement about having to run the installer in the
sysupgrade compat warning for the Linksys E8450 (UBI).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Probing of the fitblk driver in some situations happens after the kernel
attempts to mount rootfs, which then fails.
Always use 'rootwait' when using fitblk for rootfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cleanup uart1-related node on ELECOM WAB-I1750-PS and enable it for
"SERIAL" port on the case.
"SERIAL" port can be used for OpenWrt console by adding the following
line to /etc/inittab and rebooting:
ttyATH1::askfirst:/usr/libexec/login.sh
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add aliases with "serialN = &uartN;" of uart0/1 on QCA955x SoCs to
qca955x.dtsi, to enable uart1 on Linux Kernel.
without this:
[ 0.342915] ar933x-uart 18500000.uart: unable to get alias id, err=-19
Additionally, remove "serial0 = &uart;" alias from QCA955x device
dts/dtsi files.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add HighSpeed UART support to QCA955x series SoCs as a secondary UART
(uart1). This UART is compatible with qca,ar9330-uart.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Rename the DT label of the primary UART on Qualcomm Atheros QCA955x
series SoCs to "uart0" from "uart" for the preparation to add HighSpeed
UART (uart1) support.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
with 6.1, the kernel no longer fitted into the 16 MiB and
kicking down the can and increasing KERNEL_SIZE to 20 MiB
didn't help as the device failed to boot.
Using 'kernel-bin | gzip | uimage gzip' didn't work since the
uboot does not have enough heap to decompress these big kernels.
And finally playing around with uboot was more a hassle than
converting this device to take the simpleImage-boot-route in
the future.
Note: The device now takes even longer on the first boot-up after
the flash due to JFFS2 initializing all the remaining flash.
Be prepared to wait up to 10 minutes before the green status LED
stops blinking and will shine a solid green!
(On the plus site: the device now has ~10 MiB of additional
space for rootfs+rootfs_data).
Note2: This patch includes a kernel patch refresh.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kernel and initramfs size grows. Now uncompressed initramfs image and
regular kernel image overlaps configured area:
Initramfs:
WRAP arch/powerpc/boot/simpleImage.br200-wp
INFO: Uncompressed kernel (size 0x1428688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1500000)
WRAP arch/powerpc/boot/simpleImage.tl-wdr4900-v1
INFO: Uncompressed kernel (size 0x1428688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1500000)
WRAP arch/powerpc/boot/simpleImage.ws-ap3715i
INFO: Uncompressed kernel (size 0x1428688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1500000)
Regular image:
WRAP arch/powerpc/boot/simpleImage.br200-wp
INFO: Uncompressed kernel (size 0x10e0688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1100000)
WRAP arch/powerpc/boot/simpleImage.tl-wdr4900-v1
INFO: Uncompressed kernel (size 0x10e0688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1100000)
WRAP arch/powerpc/boot/simpleImage.ws-ap3715i
INFO: Uncompressed kernel (size 0x10e0688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1100000)
Let's change wrapper address to safe value.
Tested on: TL-WDR4900, BR200-WP
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch replaces 'of_flat_dt_is_compatible' with 'of_machine_is_compatible'.
The TL-WDR4900 platform file won't compile in the 6.1 kernel. The platform
files for the rest of the routers have been reworked or based on newer
solutions.
Let's make the TL-WDR4900 consistent with them.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This fixes the following compile problem:
````
CC arch/mips/kernel/vpe-mt.o
arch/mips/kernel/vpe-mt.c: In function 'vpe_run':
arch/mips/kernel/vpe-mt.c:32:23: error: unused variable 'physical_memsize' [-Werror=unused-variable]
32 | unsigned long physical_memsize = 0L;
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:289: arch/mips/kernel/vpe-mt.o] Error 1
````
physical_memsize was removed from upstream kernel, see:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=5b4f6c5ff65c8551018ccea40c569afd759734c0
Fixes: 387fde0da0 ("kernel: bump 5.15 to 5.15.150")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 2d63d42f5e ("mediatek: convert to new LED color/function
format where possible") leaves Xiaomi Redmi AX6000 un-converted,
the two LEDs become dead.
Now, LEDs are alive again.
Fixes: 2d63d42f5e ("mediatek: convert to new LED color/function
format where possible")
Signed-off-by: Furong Xu <xfr@outlook.com>
ath25 has been on life support for the last couple of releases, eventually
leading to marking it as source-only in 2023.
It has been basically only touched to do a kernel bump so that we can make
the new OpenWrt release which was a challenge due to small RAM amount.
However, with the attempt of kernel 6.1 update it turns out that kernel
cannot even finish booting due to RAM constraints, so its time to let this
target go.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX214 is a 802.11 ax dual-band AP
with PoE. (similar to Engenius EWS357APV3)
Specifications:
• CPU: Qualcomm IPQ6010 Quad core Cortex-A53
• RAM: 512MB of DDR3
• Storage: 128MB NAND (Macronix MX30UF1G18AC)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WIFI:
2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
4 x GPIO-controlled LEDs
- 1 Power LED (orange)
- 1 LAN LED (blue)
- 1 WIFI 5g LED (blue)
- 1 WIFI 2g LED (blue)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An populated serial header is onboard, format is
1.25mm 4p (DF13A-4P-1.25H)
RX/TX is working, bootwait is active, secure boot is not
enabled.
The root password of the stock firmware is unknown,
but failsafe mode can be entered to reset the password.
Installation Instructions:
- obtain serial access
- stop auto boot (press "4", Entr boot command line
interface)
- setenv active_fw 0 (to boot from the primary rootfs,
or set to 1 to boot from the secondary rootfs
partition)
- saveenv
- tftpboot the initramfs image
- bootm
- copy
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
to the device
- write the image to the NAND:
- cat /proc/mtd and look for rootfs partition (should
be mtd11,
or mtd12 if you choose active_fw 1)
- ubiformat /dev/mtd11 -f -y
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
- reboot
Note: the firmware is senao-based. But I was unable to build
a valid senao-header into the image.
Maybe they changed the header format and senaoFW isn't
working any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
BCM63xx maintainance is a PITA since there's no full Device Tree support and
therefore every board needs it's own definition in board_bcm963xx.c
There's no DSA support for this board and there have been very few
contributions in the last years.
Moreover, BCM63xx SoCs >= BCM6358 are already supported in bmips target, so
any efforts to keep this target alive aren't worth the time.
Let's focus the community efforts on improving bmips instead.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
In a pristine build, these directories are created as dependencies of
the tools subdir compile, however this step never runs when the tools
compile stamp already exists. Since commit ed6ba2801c ("tools: keep
stamp file in $(STAGING_DIR_HOST)"), this will happen after `make clean`:
$(STAGING_DIR) has been deleted, but the tools stamp still exists, so
the next build will fail because $(STAGING_DIR) has not been set up
correctly.
Fix builds after `make clean` by adding the preparation as dependencies
for the target and package directories as well.
Fixes: ed6ba2801c ("tools: keep stamp file in $(STAGING_DIR_HOST)")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The SolidRun ClearFog Pro is a router based on the SolidRun CN9130 SOM.
Specs:
- SoC: Quad-Core Cortex-A72 CN9130 SoC
- RAM: 4GiB DDR4
- Serial: Micro-USB port on front (FT232R, 115200 8n1)
- Storage: 8GiB eMMC, microSD card slot, 8MiB SPI NOR flash
- Ethernet: 7x GbE (1 port dedicated on SoC, 6 port switch with single GbE CPU port)
- SFP: 1x SFP+
- USB: 1x USB-A 3.1 Gen 1
- PCIe: 2x mini PCIe (one slot with USB and SIM card socket)
- SATA: 1x M.2 Key-B
In addition to the usual connectivity options this device also features
an internal mikroBUS expansion connector.
SATA is currently untested due to lack of a suitable M.2 SSD.
Installation
============
1. Write sdcard sysupgrade image to microSD card using dd or similar
2. Insert microSD card into router and apply power
3. Device boots into OpenWRT
4. (optional) dd sysupgrade image to /dev/mmcblk0 to install to eMMC
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
Upstream a patch adding support for cpufreq on AP807-based SoC like the
CN913x was submitted. Include it in patches to ensure best performance
under load and lowest power consumption in idle.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
ELECOM WAB-I1750-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 3T3R
- 2.4 GHz : Qualcomm Atheros QCA9558 (SoC)
- 5 GHz : Qualcomm Atheros QCA9880
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 2x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- "SERIAL" : RS232C (+-12V)
- port : ?
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- settings : 115200n8
- note : compatible with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1.04 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.26 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-I1750-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- "SERIAL" port is provided by HS UART on QCA9558 SoC that has
compatibility with qca,ar9330-uart, but QCA955x SoC's is not supported
on Linux Kernel and OpenWrt.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): 00:90:FE:xx:xx:0A (Config, ethaddr (text))
2.4GHz : 00:90:FE:xx:xx:0A (Config, ethaddr (text))
5GHz : 00:90:FE:xx:xx:0B
[original work]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[update for NVMEM and others]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9557.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S1167-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S600-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): 00:90:FE:xx:xx:04 (Config, ethaddr (text))
2.4GHz : 00:90:FE:xx:xx:04 (Config, ethaddr (text))
5GHz : 00:90:FE:xx:xx:05
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
ELECOM WAB-S600-PS is a 2.4/5 GHz band 11n (Wi-Fi 4) access point, based
on QCA9557.
This device also supports 11ac (Wi-Fi 5) with the another official
firmware.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S600-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S1167-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
2.4GHz : BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
5GHz : BC:5C:4C:xx:xx:7D
[original work of common dtsi part for WAB-I1750-PS]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[adding support for WAB-S600-PS]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The original commit had an invalid setting of the
led status for this device.
There is no gpio pin connected to that led so lets
remove these from the u7621-01 dtsi file.
Signed-off-by: David Bentham <db260179@gmail.com>
Update the default network configuration for Gateworks Newport boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge:
- gw610x/gw6903; single NIC: eth0
- gw620x/gw630x; two NIC's from left to right are: eth1 eth0
- gw640x; multiple NIC's from left to right: eth4 eth0 eth1 eth2 eth3
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
it is possible to boot and run OpenWrt from an image on an USB-Stick
on the MyBook Live DUO. (No, the MyBook Live Single does NOT have an
USB-Port and attempts at enabling it sadly all failed... so far).
To do that:
First, prepare a USB-Stick by writing the raw and uncompressed OpenWRT
factory image for the device onto the stick (i.e.
# gunzip -c openwrt-*wd_mybooklive*-factory.img.gz > /dev/sd$XX).
Then enter the u-boot via an attached TTL/CMOS 3.3V cable adapter and
give the following commands a try in the:
usb start; sata init
ext2load usb 0:1 ${fdt_addr_r} /boot/apollo3g.dtb
ext2load usb 0:1 ${kernel_addr_r} /boot/uImage
setenv bootargs 'root=/dev/sdc2 rw rootfstype=squashfs,ext4 rootdelay=5'
run addtty; bootm ${kernel_addr_r} - ${fdt_addr_r}
Notes:
- booting from USB-Sticks takes a long time! Be prepared to wait a few
minutes. (~3 minutes for 4 MiB /boot/uImage file on a USB 2.0 Stick)
- the bootargs part 'root=/dev/sdX2' depends on how many HDDs/SSDs are
slotted in. (if none: then use sda, if one: sdb. if two: sdc)
- rootdelay is important as the storage on the USB-Sticks do not show
up fast enough. 5 seconds might be excessive though.
- it's possible to concat these commands together in one line and
write it into u-boot's "bootcmd" environment variable and save the
environment to make the device to always boot from USB from then on.
if you have accidentally overridden the 'bootcmd' and want to return
to 'spec' enter the following commands :
setenv bootcmd 'run boot_sata_script_ap2nc'
saveenv
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Note about the MyBook Live.
The MyBook Live didn't have the encompassing fixed-partitions.
This is needed for the u-boot,env compatible to be read as otherwise
the kernel assumes this is a legacy NOR/NAND node and this binding
is unsupported.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Enable DEBUG_BUGVERBOSE by default on qualcommax as without it once BUG()
is called we will not get any output other than
"------------[ cut here ]------------"
which is not usefull at all, so since we dont have kernel size constraints
lets enable it by default.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use type casts to prevent compiler warnings which are going to turn
into errors when we switch to Linux 6.6.
In the long run we should try to get rid of this downstream driver
now that RTL8367S is support by the rtl8365mb DSA driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rename kernel patches accepted upstream to indicate at which version
they have been accepted, replacing downstream variants which what was
accepted upstream. Note that some of them are fixes which will
find their way to older kernel versions as well via linux-stable.
No functional changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some backported thermal patches ended up with the wrong kernel
version in their filename. Fix this.
Fixes: c36de2e73a ("mediatek: backport a hell of thermal commits")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Kirkwood SoCs all have an onchip RTC that can hold the time
over e.g. a reboot which will help if no NTP servers are available.
Create a kernel module package for the Marvell RTC, and add it to
all Kirkwood devices that do not have their own discrete
battery-backed RTC. Adding it to platforms with a proper RTC
is just surplus.
All Kirkwoods have at least one RTC so add RTC to the features
list for Kirkwood as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MT7981B /256MB /16MB SPI (XM25QH128C)
AX 2.4Ghz
AX 5Ghz 160Mhz wide
1Gbit LAN
OEM:
root@RE3000:~# ifconfig |grep HWaddr
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0
rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0
rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0
OpenWrt
root@OpenWrt:/# ifconfig |grep HW
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1
tftp Installation via u-boot:
Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin
write to flash via sysupgrade or gui
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
This target adds support for the Allwinner D1 RISC-V based SoCs.
- RISC-V single-core T-Head C906 (RV64GCV)
- Tensilica HiFi4 DSP
- DDR2/DDR3 support
- 10/100/1000M ethernet
- usual peripherals like USB2, SPI, I2C, PWM, etc.
Four boards are supported:
- Dongshan Nezha STU
- 512Mb RAM
- ethernet
- LicheePi RV Dock
- 512Mb RAM
- wireless-only (RTL8723DS)
- MangoPi MQ-Pro
- 512Mb RAM
- there are pads available for an SPI flash
- wireless-only (RTL8723DS)
- Nezha D1
- 512Mb/1Gb/2Gb RAM
- 256Mb NAND flash
- ethernet, wireless
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The boot loader does not have a fixed size limit for the kernel,
so we're free to change the layout. This may break sysupgrade, but a fresh
flash from initramfs works.
Fixes: 6e2962d4c5 ("mediatek: mt7622: skip build for MT7622 rfb1 (UBI)")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The Arcadyan VRV9510KWAC23 (trade name Livebox Next) is a Lantiq router distributed by some spanish ISPs
Hardware:
- SoC: Lantiq VRX200
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 256 MiB DDR2
- Flash: 128 MiB NAND
- Ethernet: Built-in Gigabit Ethernet switch, 5x 1GbE
- Wifi 2.4GHz: Broadcom BCM43222KFBG 802.11b/g/b MIMO 2T2R
- Wifi 5GHz: Broadcom BCM4360KMLG 802.11ac MIMO 3T3R
- USB: 2x USB 2.0
- DSL: Built-in VDSL/ADSL2+ XWAY VRX208
- LEDs: 8x
- Buttons: 4x
- Phone: Lantiq PEF 42068 V XWAY SLIC120
Install instructions:
Detailed instructions can be found on the wiki https://openwrt.org/toh/arcadyan/vrv9510kwac23
1. Boot into UART mode and upload the the https://raw.githubusercontent.com/danielhuici/arcadyan-vrv9510kwac23-utils/main/u-boot.asc file via serial console to boot into U-Boot.
2. Perform a backup of the NAND
3. Setup a TFTP server and serve the https://github.com/danielhuici/arcadyan-vrv9510kwac23-utils/raw/main/u-boot.ltq.lzo.nandspl. Replace the OEM bootloader with this one. Erase your NAND and write the image into it
4. Reboot the router
5. Serve the OpenWrt ramdisk image on your TFTP server and boot it via U-Boot
6. When OpenWrt boots, flash the SquashFS OpenWrt image using LuCi interface, so OpenWrt gets installed into the NAND
Signed-off-by: Daniel Huici <danielhuici@hotmail.com>
Drop the flow-hash of the skb when forwarding to the L2TP netdev.
This avoids the L2TP qdisc from using the flow-hash from the outer
packet, which is identical for every flow within the tunnel.
This does not affect every platform but is specific for the ethernet
driver. It depends on the platform including L4 information in the
flow-hash.
Signed-off-by: David Bauer <mail@david-bauer.net>
The following kernel module package was added to the build recipe for the
Turris Omnia: kmod-mt7915-firmware
This module enables support for the official Wi-Fi 6 upgrade kit sold by
CZ.NIC, which includes the AW7915-NP1 miniPCIE board based on Mediatek
MT7915AN, providing 5 GHz Wi-Fi 6 connectivity. With this commit we now
support the latest Turris Omnia Wi-Fi 6 Edition
Signed-off-by: Jan Jasper de Kroon <jajadekroon@gmail.com>
Because some still unresolved bugs in this driver, which sprout
occasional questions what this patch works around, point to the issue
which started this. Being here, fill headers required by git am.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reduce and split pcie controller memory ranges for en7523 SoC
in order to properly load a pcie card on the second port.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
If selected on a per-board base, fitblk doesn't end up in initramfs
images which always only come with the subtarget's default packages.
Hence fitblk needs to be included as a default package of all
subtargets making use of fitblk instead of it being selected for
individual boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we got fitblk_get_bootdev in /lib/upgrade/common.sh we don't
need platform_get_bootdev in each of the subtargets any longer.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When building the UBI NVMEM provider on 32-bit platforms a compiler
warning is triggered due to different sizeof(int).
Fix this by using integer types with well-defined size.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In official OpenWrt we use kmod-r8169 driver provided by upstream kernel
instead of kmod-r8168 driver from Realtek.
Fixes: afca1236f3 ("rockchip: add NanoPi R4S Enterprise Edition build")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The device booting successfully indicates that bootloader has been
updated. Set compat_version to 1.1 on new configs and bump
compat_version to 1.1 on first boot after a successful sysupgrade.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Without UBINIZE_OPTS it is possile to have error:
"ubi0 error: ubi_attach_mtd_dev: failed to atach mtd23, error -22"
This solve this problem.
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
TP-Link Archer C5 v4 is a dual band router with 5 GbE ports
Advertised as AC1200 for its 867Mbps (2x2) 5GHz band
and 300 Mbps (2x2) 2.4GHz band.
Specs:
- SoC: MediaTek MT7620A
- Ethernet: 5x GbE ports (Realtek RTL8367S)
- Wireless 2.4GHz: MediaTek MT7620A
- Wireless 5GHz: MediaTek MT7612E
- RAM: 64MiB
- ROM: 8MiB (GD25Q64CSIG)
- 1 USB 2.0 port
- 2 Buttons (WPS and reset)
- 8 LEDs
Flash instructions:
Currently one has to install OpenWrt only via the serial console
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
tftp 0x80060000 test.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[Update leds, add fast-read]
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[Rebuilt version based on mt7620 tplink_archer.dtsi, support for external LNA, remove bad cell count info]
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
From driver point of view no differance between rtl8367b and rtl8367s
if it connected through EXT2 (rgmii only).
So this trivial patch add some identification and initialization only.
SGMII/HSGMII mode for EXT1 is not implemented for the sake of patch
clairity.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
[Fix code format]
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[add flags to separate chip_num/chip_id detection; drop error print in
rtl8367b_init_regs, drop unnecessary info prints, code style fixes]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[rebase; use MII macros]
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[code optimization]
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Set root=/dev/fit0 cmdline parameter as the kernel won't mount rootfs
otherwise after the change from the FIT partition parser to the fitblk
driver which replaces it.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel warns about comparision of different types without cast when
building the fitblk driver on 32-bit platforms.
Fix this by using `min_t(size_t, ...`.
Fixes: 8fc5457869 ("kernel: add pending fitblk uImage.FIT sub-image block driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623.
Introduce boot device selection for fitblk's /chosen/rootdisk
handle, similar to how it is already done on MT7622, MT7986 and MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
**Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem.
SoC Type: Qualcomm IPQ4019
RAM: 512 MiB
Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC)
Bootloader: U-Boot
Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink
WiFi class AC2200:
- radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels
- radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz
- radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on.
Ethernet: 2x1GbE (WAN/LAN1, LAN2)
LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white
USB ports: No
Buttons: 2 Reset and SYNC(WPS)
Power: 12 VDC, 2,5 A
Connector type: Barrel
OpenWRT Installation
1. Simplest way is just do upgrade from webpage with *factory.img
2. You can also do it with standard tool for Netgear's debricking - NMPRFlash
3. Most advanced way is to open device , connect to UART console and :
- Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10)
- Connect serial console (115200,8n1) to UART connector
- Connect TFTP server to RJ-45 port
- Stop in u-Boot and run u-Boot command:
> setenv serverip 192.168.1.10
> set fdt_high 0x85000000
> tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb
> bootm 0x83000000
- Login via ssh
- upload or download *sysupgrade.bin ( like wget ... or scp transfer)
- Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”)
Back to Stock
- Download firmware from official Netgear's webpage , it will be *.img file after decompressing.
- Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash )
Open the case
- Unscrew nuts and remove washers from antenna's conectors.
- There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it
- Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that.
- PCB is screwed with 4Pcs of Torx T10 screws
- Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires)
- On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg )
BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org.
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
Replace ARM bootloader patch with pending upstream version. The patch
got reviewed upstream and tested on a Netgear R7800.
This fix a problem with the ARM decompressor and permits to use
AUTO_ZRELADDR without having to hardcode PHYS_OFFSET as the bootloader
now correctly parse the memory modes in the appended DTB.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
All mt7622 board previously using the FIT partition parser have been
converted to use the fitblk driver:
6aec3c7b5b mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build
41c053141e mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblk
208f6c1232 mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblk
Remove the now no longer needed FIT partition parser from builds for
mt7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add node to support the QUP4 SPI controller inside of IPQ8074.
Some devices use this bus to communicate to a Bluetooth controller.
Signed-off-by: Robert Marko <robimarko@gmail.com>
add back WIFI eprom addresses pointer in mt7621_dlink_dir-xx60-a1.dtsi
Change MAC address pointer from factory_e006 to factory_e000 + 3
same as used in D-link firmware 1.11 DIR-1960-A1
DIR-1960-A1,DIR-2640-A1,DIR-2660-A1,DIR-3060-A1
Clean-up MAC addresses in D-Link NOR devices DTS's
Change WIFI MAC Addressees to the same as NAND cousins macaddr_factory_e000 + ?
as later devices don't have the MAC address in factory configuration
same as used in D-Link firmware 1.30 DIR-878-A1
DIR-867-A1,DIR-878-A1,DIR-878-R1,DIR-882-A1,DIR-882-R1,DIR-1935-A1
* D-link software differs between source of wan address
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Now we support parsing the color and function properties.
Ref: e814acc599 ("base-files: support parse DT LED color and function")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
[port 8ed390a (qualcommax: set correct PHY mode for port 0-4) to ipq60xx]
Port 0-4 have the mode set to SGMII instead of PSGMII. Now that we use
he upstream qca807x driver, this conflicts with the qca SSDK driver
that expects the mode to be PSGMII as for not integrated driver, it does
refer to the real PHY mode.
Update the entry for port 0-4 to PSGMII to solve warning from qca SSDK
in ipq6018-ess.dtsi.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Hardware
--------
RockChip RK3566 ARM64 (4 cores)
- up to 8GB LPDDR4X
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- 10/100/1000 Base-T
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Simple AQR hack patch has been merged upstream, hence we can drop it from
hack directory and move it to backport.
The patch for 5.15 are correctly reworked to align to outdated API.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address)
to "enterprise" edition, and it was added as a "new" board in upstream
kernel.
This patch switched to use that upstreamed dts and removed local
EEPROM patch.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Ubiquiti WA devices with newer hw version (sold 2023)
require UBNT_VERSION to be at least 8.7.4, otherwise
the image is rejected.
For consistency, also increase version number for XC devices.
Signed-off-by: Martin Garbe <monomartin@opennet-initiative.de>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Fix style of nvmem cell names in the device tree of the GL.iNet MT-2500.
Fixes: 49ed52b862 ("mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMC)"
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Recent OEM firmware versions test the version number embedded in the uimage
"name" header field. The exact restricton is unknown, but "7.0.8.4" seems
to be the lowest number accepted on a GS110TPPv1 which already has that
version or higher.
A "9.9.9.9" version is accepted as valid by the GS110TPPv1 OEM firmware,
and considered both unique enough to identify an OpenWrt image and
moderately future proof against OEM version bumps.
This change is also boot tested on a GS108Tv3 with
"BOOT Loader Version 1.0.0.2 (2018-08-31 17:05:26 UTC)"
to verify that it doesn't break boot on older hardware.
Link: https://forum.openwrt.org/t/72510/58
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Import patch to make sure SGM_REG_SEL clock is always enabled as it
seems that more registers than just SGMIISYS0 and SGMIISYS1 are
depending on that clock being enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we can reference MMC partitions in device tree, use that
to get rid of Wi-Fi EEPROM and MAC address setup in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use device_set_node to make sure OF node gets assigned on block
devices to be used as NVMEM providers. While block partitions were
already working fine as NVMEM providers, bare block devices such as
mmcblk0boot1 will not work without this change.
Fixes: fc153aa8d9 ("kernel: import pending patches adding support for NVMEM on UBI and MMC")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
UNIPHY2 on the WAX630 is connected to a QCA8081 PHY which is only 2.5G and
it does not support using USXGMII at all but rather only SGMII or SGMII+.
Tested-by: Kristian Skramstad <kristian+github@83.no>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove inaccurate compatible string 'mediatek,mt7986-ethsys' which
results in the wrong clock driver probing on MT7981 with Linux 6.1 and
ends up freezing the system once WED is used.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by
host system. With built-in drivers this doesn't work in OpenWrt /
embeddded as filesystem isn't available during PHY probe. That results
in delays like:
[ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld
[ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110)
Switch to module to postpone PHY probe to init state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14
Since this is not Qnap 301W specific lets fix it subtarget wide by
declaring the correct PHY mode for 10G AQR-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14
So, lets fix 10G AQR ports by declaring the correct PHY mode.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also here build fails due to increased kernel size.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Due to increased kernel size the build currently fails if including
the MT7622 rfb1 (UBI). Skip it for now until there is a better
solution (such as replacing the bootloader and changing the flash
layout).
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Include the needed Ethernet PHY driver module for the BananaPi R3 mini.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Reported-by: BPI forum user nezar_taima
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
One of the pins requiered by M.2 slot is conflict with spi1,
however, spi1 seems unused so simply disable it for now, this
matches the factory behavior [1].
1. 9bd78779f2
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Conversion to new LED color/function format and drop label format.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property can be
removed in favor of the new format.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This commit fixes the alphabetical order in 02_network.
The 2 deco devices in ath79_setup_interfaces() were in the wrong place.
Signed-off-by: Foica David <superh552@gmail.com>
Since we can configure the PHY LED of the qca8081,
add a configuration for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The dts of Arcadyan AW1000 forgot to convert qca807x PHY
to PHY package implementation. This commit fix it.
Fixes: 0ab4b92 ("qualcommax: convert qca807x PHY to PHY package implementation")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Generate ubinized image as ARTIFACT and make use of now available
generic 'ubinize-image' build step intended for that purpose.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix NAND flash layout which was out-of-sync with the definition in
ARM TrustedFirmware-A which expects UBI to start at 0x200000.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The U-Boot binary for the RAVPower RP-WD009 has been renamed.
In order to be uniform with all other U-Boot binaries generated the SoC type has been prepended.
Set that new name also in the image build recipe for that device in order to fix build.
Fixes: 927334a8f7 ("uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
update the default network configuration for Gateworks Ventana boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Hardware specification
----------------------
SoC: MediaTek MT7986A 4x A53
Flash: 128MB SPI-NAND, 8GB eMMC
RAM: 2GB DDR4
Ethernet: 2x 2.5GbE (Airoha EN8811H)
WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
Interfaces:
* M.2 Key-M: PCIe 2.0 x2 for NVMe SSD
* M.2 Key-B: USB 3.0 with SIM slot
* front USB 2.0 port
LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
Button: Reset, internal boot switch
Fan: PWM-controlled 5V fan
Power: 12V Type-C PD
Installation instructions for eMMC
----------------------------------
0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt
running there).
1. Write GPT partition table to eMMC
Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to
the device /tmp using scp and write it to /dev/mmcblk0:
dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0
2. Reboot (to reload partition table)
3. Write bootloader and OpenWrt images
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate partitions:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5
sync
4. Remove the device from power, set boot switch to eMMC and boot into
OpenWrt. The device will come up with IP 192.168.1.1 and assume the
Ethernet port closer to the USB-C power connector as LAN port.
5. If you like to have Ethernet support inside U-Boot (eg. to boot via
TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1:
echo 0 > /sys/block/mmcblk0boot1/force_ro
dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1
dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1
Installation instructions for NAND
----------------------------------
0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there
by instructions above. Using stock rom or immortalwrt does NOT work!)
1. Write things to NAND
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate locations:
mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0
ubidetach -m 1
ubiformat /dev/mtd1
ubiattach -m 1
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip)
ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static
ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
cd /lib/firmware/airoha
cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static
ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976
ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
3. Remove the device from power, set boot switch to NAND, power up and
boot into OpenWrt.
Partially based on immortalwrt support for the R3 mini, big thanks for
doing the ground work!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add PHY driver for Airoha EN8811H PHY and package it as kernel module.
The PHY needs to load firmware from rootfs, so there is no point in
having the driver built-into the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Firmware for the built-in 2.5G Ethernet PHY of the MediaTek MT7988 SoC
is now part of linux-firmware, so we can package it.
Only a single file is needed with recent driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Switch to all-UBI layout on SPI-NAND
* use fitblk driver instead of uImage.FIT partition parser
* adapt sysupgrade
* bump COMPAT_VERSION
Remove BROKEN mark now that all needed changes are done.
Boards running images generated before this commit will require
full reflash of the bootloader, re-install from SD card is the
easiest way to achieve that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add environment settings for the BananaPi BPI-R4 router board which
can boot from (and store its bootloader environment on) micro SD card,
SPI-NAND and eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SOC: MediaTek MT7988A (4x Cortex-A73)
RAM: 4 GiB DDR4
Flash: 128 MiB Winbond SPI-NAND
MMC: 8 GiB eMMC *or* microSD (cannot be used both)
ETH: 4x 1GE (1x WAN, 3x LAN)
2x SFP+ (10G, 5G, 2.5G, 1G)
USB: on-board USB 3.2 4-port hub
1x USB 3.2 port (type A connector)
1x M.2 for 4G/5G modem
2x mPCIe for additional modems
WiFi: optional MediaTek MT7996 Wi-Fi 7 module
(using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)
Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).
2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.
3. Switch to boot from SPI-NAND and install to eMMC.
Known issues
------------
- The RST button is hard-wired to the SoC reset and can't be read
from software. This can be changed by modifying the board (ie.
moving a 0-ohm resistor). However, in order to maintain compatibility
with the board as it comes from factory the button isn't used by
OpenWrt and the WPS button is used as factory/reset button instead.
- various small things still need to be fixed in DT
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch from MediaTek SDK which allows using the third
PCIe host controller of the MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add UART pinctrl group for using only pins 80 and 81 for uart1.
This is needed on the BPi-R4 as RTS/CTS signals are used for other
on-board functions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace previous patch adding paths and SerDes modes with patch series
pending upstream adding dedicated drivers for XFI T-PHY and USXGMII PCS,
extends LynxI PCS to be a standalone platform driver and as a consequence
makes much less changes to the actual Ethernet driver mtk_eth_soc.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport almost 50 commits from upstream Linux to improve thermal
drivers for MediaTek SoCs and add new LVTS driver for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let's pick a bunch of useful phylink changes which allow us to keep
drivers in sync with mainline Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add 'fitblk' driver to replace the rejected/deprecated uImage.FIT
partition parser.
To use the new driver, add phandle /chosen/rootdisk and point it to
the MTD partition, UBI volume or block device holding the uImage.FIT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Similar to supporting nvmem-layouts on MTD devices, also allow referencing
UBI and MMC devices in DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to allow gradually migrating the boards currently using the
uImage.FIT partition (deprecated/rejected) parser to the new fitblk
driver, skip the partition parser code in case the new fitblk driver
(which serves the same purpose) is used.
As an indicator for the use of the new fitblk driver, check if the
/chosen/rootdisk property is present in the Device Tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The partition parser approach has been rejected upstream, it will be
replaced by a small block driver which is the solution suggestion by
upstream maintainers.
As the partition parser has only been used by the mediatek target, as
a first step, move it there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport two commits from Linux 6.3 wiring up device node parents of
ubi devices (pointing to their MTD parent) as well as ubiblock devices
(poiting to their parent UBI volume).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Convert qca807x PHY to new implementation like for other devices.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Now that Malibu (QCA807x) PHY is using the upstream driver, we dont need
support to define address of the first PHY in package, so remove the
malibu_first_phy_addr DTS property.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that QCA807x interface mode check was upstreamed, use the upstreamed
version and mark it as such.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use order described as preferred in DTS Coding Style. Mostly just move
"compatible", "reg", "ranges" and "status" properties.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
PoE devices in the realtek target have the possibility to add PSE info
to the board description via 02_network. Make this available for all
targets, by moving the uci_set_poe() function to the globally available
uci-default.sh script.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
uci_set_poe() now performs two duties: filtering the list of device
ports to exclude non-PoE ports, and generating the PoE related device
config.
Extract the port filtering to an external function, which is made a bit
more readable by the use of 'sort -V [-r] | uniq -u' to filter duplicate
entries out of a (reverse) version sorted list.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The ZyXEL XGS1250-12 has a chassis fan. The fan is positioned perfectly to
provide additional cooling to the Aquantia NBase-T phys. Testing has shown
that the phys can reach temperatures upwards of 72 degrees Celsius quite
easily at about 20 degrees Celsius ambient.
Support the chassis fan to give the phys a bit of extra cooling.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This reverts commit 131e41614d.
Sadly it makes menuconfig fail with
tmp/.config-package.in:171: glob failed: No files found "feeds/base/utils/busybox/Config.in"
make: *** [/usr/src/openwrt/include/toplevel.mk:136: menuconfig] Error 1
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building a package in the build system or the SDK results in different
values for the `SOURCE` property, it's either `packages/<package name>`
or `feeds/base/<package name>`. The reason is that the SDK handles
`openwrt.git` as an external feed called while the build system contains
the *base* packages directly.
Since packages created with either method are (ideally) the same (bit
for bit), align the content of SOURCE. To do so this commit creates a
symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE
when building from inside the build system.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Currently, we are checking whether the PHY package mode matches the
individual PHY interface modes at PHY package probe time, but at that time
we only know the PHY package mode and not the individual PHY interface
modes as of_get_phy_mode() that populates it will only get called once the
netdev to which PHY-s are attached to is being probed and thus this check
will always fail and return -EINVAL.
So, lets move this check to .config_init_once as at that point individual
PHY interface modes should be populated.
Fixes: 16364e4100 ("generic: 6.1: backport QCA807x PHY patches")
Signed-off-by: Robert Marko <robimarko@gmail.com>
This Qualcomm Gigabit phy driver was mistakenly added because
MT76x8 does not support external phy, and it only supports max
100M full duplex speed.
Fixes: cadf517107 ("ralink: add support for mt7628")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Xiaomi AX9000 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Xiaomi AX3600 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Also enable CONFIG_PHYLIB_LEDS to actually expose the PHY LEDs if
defined in DT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert every qca807x PHY definition in DT to new PHY package
implementation to correctly support applying fixup for the correct PHY
mode.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Port 0-4 have the mode set to SGMII instead of PSGMII. Now that we use
the upstream qca807x driver, this conflicts with the qca SSDK driver
that expects the mode to be PSGMII as for not integrated driver, it does
refer to the real PHY mode.
Update the entry for port 0-4 to PSGMII to solve warning from qca SSDK
in ipq8074-ess.dtsi.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
IPQ807x have integrated qca8074 PHY supported by the upstream qca807x driver.
Enable it to use it instead of the downstream qca SSDK variant.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adapt patches to new Upstream QCA807x PHY driver.
Rework the PHY patch to new PHY Package nodes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport QCA807x PHY patches merged upstream that introduce the new
concept of PHY package.
Also add in generic config the new Kconfig CONFIG_QCA807X_PHY.
All affected patch automatically refreshed with make
target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport Aquantia PHY endianess patch. While the current implementation
works ok for Little-Endian targets, backport patch to prevent any kind
of malfunction if in the future we will have Big-Endian target with
Aquantia PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit d737ae99cb ("qualcommax: Fix Buffalo WXR-5950AX12 Ethernet
DTS") reverted the switch bmp to the original OEM definition and
added the malibu_first_phy_addr property.
Problem is that OEM bmp definition is wrong and actually doesn't make sense,
probably caused by copy-paste of the QCOM reference DTS without actually
setting real values. What actually fixed the regression was adding the
malibu_first_phy_addr as without it the MALIBU PHY was actually not
correctly configured and the Aquantia PHY were actually configured as
MALIBU PHY.
Fix all these wrong PHY definition.
The BPM is reverted and the following fixes are applied:
- Drop ESS_PORT1 as it's not actually attached in HW.
- Move ESS_PORT5 AGAIN from lan to wan. This refer to the first Aquantia
PHY that is labelled "wan"
- Move ESS_PORT6 AGAIN from wan to lan. This refer to the second
Aquantia PHY that is labelled "lan1".
Also PHY tag in MDIO node are renumbered to start from 0 following the
tagging standard used also in other dts and the not attached one (reg
0x18 and reg 0x1c) are correctly dropped.
Definition for port@1 in phyinfo is dropped as it doesn't exist.
dp nodes are updated to reference the new PHY tag numbering.
Fixes: d737ae99cb ("qualcommax: Fix Buffalo WXR-5950AX12 Ethernet DTS")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The NWA50AX Pro only has a eth0 interface for its only ethernet port.
Use this port for preinit.
Fixes non-working network in failsafe mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
u64_stats_init() has been unable to handle NULL pointer since
6.1 kernel. This patch fixes kernel oops on mt76x8 and rt305x
sub-target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In the 5.15 kernel, we use the staging driver version instead of the
downstream file.
Fixes: 88d982e3bd ("ramips: 6.1: mt7621-dma: add hsdma driver to files")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Fixes errors in the form of:
make[9]: Entering directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7620/linux-6.1.77'
CC drivers/net/ethernet/ralink/mtk_eth_soc.o
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1368:51: warning: passing argument 2 of 'of_get_mac_address' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
1368 | of_get_mac_address(priv->dev->of_node, dev->dev_addr);
| ~~~^~~~~~~~~~
In file included from drivers/net/ethernet/ralink/mtk_eth_soc.c:26:
./include/linux/of_net.h:16:59: note: expected 'u8 *' {aka 'unsigned char *'} but argument is of type 'const unsigned char *'
16 | extern int of_get_mac_address(struct device_node *np, u8 *mac);
| ~~~~^~~
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_probe':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1641:9: error: too many arguments to function 'netif_napi_add'
1641 | netif_napi_add(netdev, &priv->rx_napi, fe_poll, napi_weight);
| ^~~~~~~~~~~~~~
In file included from ./include/linux/etherdevice.h:21,
from drivers/net/ethernet/ralink/mtk_eth_soc.c:21:
./include/linux/netdevice.h:2611:1: note: declared here
2611 | netif_napi_add(struct net_device *dev, struct napi_struct *napi,
| ^~~~~~~~~~~~~~
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream commit f48dc6b96649 ("spi: Retire legacy GPIO handling") [0]
removed support using GPIOs as chip select. Fix it by replacing cs_gpio
with cs_gpiod.
[0] - f48dc6b966
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Change fe_hw_set_macaddr and the set_mac parameter to const to fix
errors in the form of:
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_set_mac_address':
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
174 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_hw_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1220 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c:1222:44: error: passing argument 2 of 'fe_hw_set_macaddr' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1222 | fe_hw_set_macaddr(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:155:75: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
155 | static inline void fe_hw_set_macaddr(struct fe_priv *priv, unsigned char *mac)
| ~~~~~~~~~~~~~~~^~~
cc1: all warnings being treated as errors
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped support for legacy driver [0]. Rewrite the driver like
the renesas pwm driver [1].
Fixes erros in the form of:
make: *** [/__w/openwrt/openwrt/openwrt/include/toplevel.mk:232: target/compile] Error 1
====== Make errors from logs/target/linux/compile.txt ======
| ^~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:107:19: note: (near initialization for 'mtk_pwm_ops.free')
drivers/pwm/pwm-mediatek-ramips.c:108:10: error: 'const struct pwm_ops' has no member named 'disable'
108 | .disable = mtk_pwm_disable,
| ^~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: error: initialization of 'int (*)(struct pwm_chip *, struct pwm_device *, struct pwm_capture *, long unsigned int)' from incompatible pointer type 'void (*)(struct pwm_chip *, struct pwm_device *)' [-Werror=incompatible-pointer-types]
108 | .disable = mtk_pwm_disable,
| ^~~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: note: (near initialization for 'mtk_pwm_ops.capture')
cc1: all warnings being treated as errors
[0] - 0829c35dc5
[1] - ec00cd5e63
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped slave_id in dai_dma [0]. So drop it also in the mt7620
support patch.
Fixes errors in the form of:
sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_init_dma_data':
sound/soc/ralink/ralink-i2s.c:452:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
452 | dma_data->slave_id = i2s->txdma_req;
| ^~
sound/soc/ralink/ralink-i2s.c:462:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
462 | dma_data->slave_id = i2s->rxdma_req;
| ^~
[0] - https://lore.kernel.org/r/20211122222203.4103644-3-arnd@kernel.org
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream changed in ed5c2f5fd10d ("i2c: Make remove callback return void")
the i2c driver's remove function to return no value. Adapt the driver code
to compile with 5.15 and 6.1 like it is done in other projects [0].
Fixes errors in the form of:
make[8]: Leaving directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-6.1.29'
CC drivers/pinctrl/pinctrl-aw9523.o
drivers/pinctrl/pinctrl-aw9523.c:1117:19: error: initialization of 'void (*)(struct i2c_client *)' from incompatible pointer type 'int (*)(struct i2c_client *)' [-Werror=incompatible-pointer-types]
1117 | .remove = aw9523_remove,
| ^~~~~~~~~~~~~
drivers/pinctrl/pinctrl-aw9523.c:1117:19: note: (near initialization for 'aw9523_driver.remove')
cc1: all warnings being treated as errors
[0] - https://gitlab.com/ddcci-driver-linux/ddcci-driver-linux/-/merge_requests/10/diffs
Signed-off-by: Nick Hainke <vincent@systemli.org>
Apply the "109-drivers-mt7621-dma-handle-error-from-device_reset.patch"
directly on the downstream maintained dma driver.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Commit 87dd67f496f7 ("staging: mt7621-dma: remove driver from tree")
removed the mt7621-dma driver. Maintain the driver downstream in the
folder of the other mediatek drivers.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Refresh kernel patches changed from the just introduced ipq60xx new
subtarget.
Patch automatically refreshed with make target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These recipes are generic and will be used for other subtargets, so lets
move them to the target Makefile so they can reused.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for the Qualcomm IPQ60xx SoC. WiFi support still has
to be handled and correctly fix hence this is currently marked as
source-only to have a solid base to progress on correct support of this
and hope Upstream QUIC publish newers ath11k drivers for this SoC.
Co-developed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ improve commit description, add SoB for Robert, make it source-only ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: a9e0d97e1f ("ipq40xx: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add dtb makefile target to targets list to permit correct working of
make target/linux/dtb
Fixes: c47532b1ea ("kernel-buildOnmk: add support for compiling only DTS")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
bmips has all the dt-bindings includes inside each SoC .dtsi files, so let's
move the new includes there instead of adding them to each board .dts files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 19c45b95db ("ramips: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 0c3f3eb229 ("lantiq: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 33e7962329 ("ipq806x: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch fixing kernel panic with mcast packets, patch is already
scheduled to be backported to stable kernels and will be dropped once
new stable kernel version are released.
Fixes: #14554
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The rtl93xx SoC supports both 1000Base-X and 10GBase-CR on its SerDes
interfaces. Enable dynamic switching between mac-signaled modes to
support 1000Base-X and 10GBase-CR on the SFP port.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This patch adds support for 1000Base-X and 10GBase-CR directly on the
SerDes lanes of rtl93xx SoCs.
This fixes SFP/SFP+ support on devices like the XSG1250-12.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
Backport patch to enable PHYLIB_LEDS kconfig dynamically instead of
having to select this config for every target that makes use of PHY LEDs
API.
All affected patch are automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_PHYLIB_LEDS is required in order for phylib to probe the DT for LEDs
attached to PHY-s.
Fixes: 75ad5c2 ("qualcommax: switch to qca8081 upstream PHY driver")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit daefc646e6 ("realtek: fix ZyXEL initramfs image generation")
fixed a shell expansion issue with zyxel-vers usage. Commit 045baca10b
("realtek: deduplicate GS1900 recipes") took care of this for the
rtl838x and rtl839x subtargets, but the single device officially
supported in rtl930x - the XGS1250-12 - was overlooked. This commit
updates the XGS1250-12 build recipe as well.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Add even more missing Kconfig for video-core introduced by recent fixup
to video kmods.
Fixes: 76b0d24157 ("kernel: modules: video: fix video-core for 6.1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport one patch merged upstream that prevent a deadlock for LED
netdev trigger and add a pending patch that fix kernel panic on
interface rename trigger notification with invalid dev.
Fixes: #14477
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing Kconfig for video-core introduced by recent fixup to video
kmods.
Fixes: 76b0d24157 ("kernel: modules: video: fix video-core for 6.1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linux 6.1 wraps core video drivers in a MEDIA_PLATFORM_DRIVERS submenu.
Enable that for 6.1 and add some new necessary undefines to
target/linux/generic/config-6.1 to avoid build failures.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds support for the Fritzbox 3490 device. It contains two
SoCs, one Lantiq with a 5GHz WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module which is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
- Without telephony or ISDN
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This adds support for the Fritzbox 5490/5491 devices. They contain
two SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module which is not supported with this commit.
Both devices have fiber WAN ports.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port Lantiq gswip switch,
4x 1000/100/10 port (additional qca8334 switch for 2 ports), Port 5 is
fixed and connected to the Wireless SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- AT 8033 based AON fiber port (5490) or GPON fiber port (5491)
Unsupported:
- DECT and ISDN telephony
- Two ethernet ports (on extra switch) and fiber port not working
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This adds support for the Fritzbox 7490 device. It contains two
SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module and is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
Unsupported:
- DECT and ISDN telephony
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The Fritzbox 3490, 5490 and 7490 devices have a Renesas µPD720202
USB3 PCIe device, which requires an endian switch for PCIe slave
devices. The flag and setting is not implemented in the available
patches. Since adding this setting would break other devices,
a DTB setting lantiq,switch-pcie-endianess is added for selective
enablement.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
Specifications:
lan: eth0
wan: eth1
Problem Description:
The lan wan port is reversed with the current machine.
Use eth0 as LAN port and eth1 as WAN port.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
The driver for the cellular modems serial interface and qmi was missing
from the default device packages. The driver is required to interact
with the modem using AT commands.
Signed-off-by: Jan Fuchs <jf@simonwunderlich.de>
Backport PHY package MMD patch merged upstream that add support for
writing MMD regs for the PHY package and support for writing to PHY
package at an offset.
All affected patches automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch converts ath10k calibration data to NVMEM format for
wave 1 devices with mtd ASCII MAC address. The "calibration"
NVMEM cell size is 0x844. All unportable MAC address settings
have been moved to '10_fix_wifi_mac' scripts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k calibration data to NVMEM format for
wave 1 devices with mtd binary MAC address. The "calibration"
NVMEM cell size is 0x844. The MAC addresses are assigned via dts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k calibration data to NVMEM format for
wave 1 devices with built-in MAC address. The "calibration"
NVMEM cell size is 0x844.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
