mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 05:38:00 +00:00
ipq40xx: Add support Netgear LBR20
**Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem. SoC Type: Qualcomm IPQ4019 RAM: 512 MiB Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC) Bootloader: U-Boot Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink WiFi class AC2200: - radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels - radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz - radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on. Ethernet: 2x1GbE (WAN/LAN1, LAN2) LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white USB ports: No Buttons: 2 Reset and SYNC(WPS) Power: 12 VDC, 2,5 A Connector type: Barrel OpenWRT Installation 1. Simplest way is just do upgrade from webpage with *factory.img 2. You can also do it with standard tool for Netgear's debricking - NMPRFlash 3. Most advanced way is to open device , connect to UART console and : - Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10) - Connect serial console (115200,8n1) to UART connector - Connect TFTP server to RJ-45 port - Stop in u-Boot and run u-Boot command: > setenv serverip 192.168.1.10 > set fdt_high 0x85000000 > tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb > bootm 0x83000000 - Login via ssh - upload or download *sysupgrade.bin ( like wget ... or scp transfer) - Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”) Back to Stock - Download firmware from official Netgear's webpage , it will be *.img file after decompressing. - Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash ) Open the case - Unscrew nuts and remove washers from antenna's conectors. - There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it - Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that. - PCB is screwed with 4Pcs of Torx T10 screws - Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires) - On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg ) BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org. Signed-off-by: Marcin Gajda <mgajda@o2.pl>
This commit is contained in:
Marcin Gajda
Robert Marko
parent
df3d5fd3f2
commit
07b9186e88
@ -53,7 +53,8 @@ aruba,ap-303)
|
||||
aruba,ap-365)
|
||||
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x10000" "0x10000"
|
||||
;;
|
||||
buffalo,wtr-m2133hp)
|
||||
buffalo,wtr-m2133hp|\
|
||||
netgear,lbr20)
|
||||
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x40000" "0x20000"
|
||||
;;
|
||||
linksys,ea6350v3)
|
||||
|
||||
@ -38,6 +38,7 @@ ALLWIFIBOARDS:= \
|
||||
edimax_cax1800 \
|
||||
linksys_mx4200 \
|
||||
linksys_mx5300 \
|
||||
netgear_lbr20 \
|
||||
netgear_rax120v2 \
|
||||
netgear_wax218 \
|
||||
netgear_wax620 \
|
||||
@ -154,6 +155,7 @@ $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
|
||||
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_mx5300,Linksys MX5300))
|
||||
$(eval $(call generate-ipq-wifi-package,netgear_lbr20,Netgear LBR20))
|
||||
$(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2))
|
||||
$(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218))
|
||||
$(eval $(call generate-ipq-wifi-package,netgear_wax620,Netgear WAX620))
|
||||
|
||||
@ -124,6 +124,10 @@ ipq40xx_setup_interfaces()
|
||||
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
|
||||
ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
|
||||
;;
|
||||
netgear,lbr20)
|
||||
ucidef_set_interface_lan "lan1 lan2"
|
||||
ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
|
||||
;;
|
||||
*)
|
||||
echo "Unsupported hardware. Network interfaces not initialized"
|
||||
;;
|
||||
|
||||
34
target/linux/ipq40xx/base-files/etc/init.d/modem_switch
Executable file
34
target/linux/ipq40xx/base-files/etc/init.d/modem_switch
Executable file
@ -0,0 +1,34 @@
|
||||
#!/bin/sh /etc/rc.common
|
||||
|
||||
START=15
|
||||
STOP=10
|
||||
|
||||
boot() {
|
||||
case $(board_name) in
|
||||
netgear,lbr20)
|
||||
echo "0" > /sys/class/gpio/lte_rst/value
|
||||
echo "0" > /sys/class/gpio/lte_pwrkey/value
|
||||
echo "0" > /sys/class/gpio/lte_usb_boot/value
|
||||
echo "0" > /sys/class/gpio/lte_pwm/value
|
||||
sleep 1
|
||||
echo "1" > /sys/class/gpio/lte_pwm/value
|
||||
echo "1" > /sys/class/gpio/lte_pwrkey/value
|
||||
echo "1" > /sys/class/gpio/lte_rst/value
|
||||
sleep 1
|
||||
echo "0" > /sys/class/gpio/lte_pwrkey/value
|
||||
sleep 1
|
||||
echo "1" > /sys/class/gpio/lte_pwrkey/value
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
shutdown() {
|
||||
case $(board_name) in
|
||||
netgear,lbr20)
|
||||
echo "0" > /sys/class/gpio/lte_pwrkey/value
|
||||
sleep 1
|
||||
echo "1" > /sys/class/gpio/lte_pwrkey/value
|
||||
sleep 10
|
||||
;;
|
||||
esac
|
||||
}
|
||||
@ -120,6 +120,7 @@ platform_do_upgrade() {
|
||||
glinet,gl-ap1300 |\
|
||||
luma,wrtq-329acn |\
|
||||
mobipromo,cm520-79f |\
|
||||
netgear,lbr20 |\
|
||||
netgear,wac510 |\
|
||||
p2w,r619ac-64m |\
|
||||
p2w,r619ac-128m |\
|
||||
|
||||
@ -0,0 +1,516 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "Netgear LBR20";
|
||||
compatible = "netgear,lbr20";
|
||||
|
||||
chosen {
|
||||
bootargs-append = "ubi.mtd=ubi root=/dev/ubiblock0_0";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_backlight_white;
|
||||
led-failsafe = &led_status_green;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_red;
|
||||
label-mac-device = &gmac;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 49 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_green: led-status-green {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
led_status_red: led-status-red {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
lte_rst {
|
||||
gpio-export,name = "lte_rst";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lte_pwrkey {
|
||||
gpio-export,name = "lte_pwrkey";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lte_usb_boot {
|
||||
gpio-export,name = "lte_usb_boot";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lte_pwm {
|
||||
gpio-export,name = "lte_pwm";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
soc {
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
status = "okay";
|
||||
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pinmux {
|
||||
mux_mdio {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_mdc {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_pins: serial-pinmux {
|
||||
function = "blsp_uart0";
|
||||
pins = "gpio16", "gpio17";
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
nand_pins: nand-pins {
|
||||
pullups {
|
||||
pins = "gpio52", "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x00000000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x00100000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "0:BOOTCONFIG";
|
||||
reg = <0x00200000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x00300000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "0:QSEE_1";
|
||||
reg = <0x00400000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@500000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x00500000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "0:CDT_1";
|
||||
reg = <0x00580000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@600000 {
|
||||
label = "0:BOOTCONFIG1";
|
||||
reg = <0x00600000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@680000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0x00680000 0x00080000>;
|
||||
};
|
||||
|
||||
partition@700000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0x00700000 0x00200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@900000 {
|
||||
label = "0:APPSBL_1";
|
||||
reg = <0x00900000 0x00200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@b00000 {
|
||||
label = "0:ART";
|
||||
reg = <0x00b00000 0x00080000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
precal_art_1000: precal@1000 {
|
||||
reg = <0x1000 0x2f20>;
|
||||
};
|
||||
|
||||
precal_art_5000: precal@5000 {
|
||||
reg = <0x5000 0x2f20>;
|
||||
};
|
||||
|
||||
precal_art_9000: precal@9000 {
|
||||
reg = <0x9000 0x2f20>;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
|
||||
partition@b80000 {
|
||||
label = "0:ART.bak";
|
||||
reg = <0x00b80000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c00000 {
|
||||
label = "config";
|
||||
reg = <0x00c00000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d00000 {
|
||||
label = "boarddata1";
|
||||
reg = <0x00d00000 0x00080000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
mac_address_lan: macaddr@0 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x0 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
mac_address_wan: macaddr@6 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x6 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
mac_address_wlan_5g: macaddr@c {
|
||||
compatible = "mac-base";
|
||||
reg = <0xc 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
mac_address_wlan_2nd5g: macaddr@12 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x12 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
|
||||
partition@d80000 {
|
||||
label = "boarddata2";
|
||||
reg = <0x00d80000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@dc0000 {
|
||||
label = "pot";
|
||||
reg = <0x00dc0000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ec0000 {
|
||||
label = "boarddata1.bak";
|
||||
reg = <0x00ec0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f40000 {
|
||||
label = "boarddata2.bak";
|
||||
reg = <0x00f40000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f80000 {
|
||||
label = "language";
|
||||
reg = <0x00f80000 0x00300000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1280000 {
|
||||
label = "cert";
|
||||
reg = <0x01280000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1300000 {
|
||||
label = "ntgrdata";
|
||||
reg = <0x01300000 0x09300000>;
|
||||
};
|
||||
|
||||
partition@a600000 {
|
||||
label = "kernel";
|
||||
reg = <0x0a600000 0x00700000>;
|
||||
};
|
||||
|
||||
partition@a9c0000 {
|
||||
label = "ubi";
|
||||
reg = <0x0ad00000 0x05300000>;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_i2c3 {
|
||||
status = "okay";
|
||||
|
||||
led-controller {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "ti,tlc59108"; /* really is tlc59208f */
|
||||
reg = <0x27>;
|
||||
|
||||
led_backlight_green: led-backlight-green {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
reg = <0x0>;
|
||||
linux,default-trigger = "default-off";
|
||||
};
|
||||
|
||||
led_backlight_red: led-backlight-red {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
reg = <0x1>;
|
||||
linux,default-trigger = "default-off";
|
||||
};
|
||||
|
||||
led_backlight_blue: led-backlight-blue {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
reg = <0x2>;
|
||||
linux,default-trigger = "default-off";
|
||||
};
|
||||
|
||||
led_backlight_white: led-backlight-white {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
reg = <0x3>;
|
||||
linux,default-trigger = "default-off";
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&mac_address_lan 0>;
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&swport4 {
|
||||
status = "okay";
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
&swport5 {
|
||||
status = "okay";
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
wake-gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
status = "okay";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
ieee80211-freq-limit = <5170000 5350000>;
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_9000>, <&mac_address_wlan_2nd5g 0>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-LBR20";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_1000>, <&mac_address_lan 0>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-LBR20";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
ieee80211-freq-limit = <5470000 5815000>;
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_5000>, <&mac_address_wlan_5g 0>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-LBR20";
|
||||
};
|
||||
@ -841,6 +841,24 @@ define Device/netgear_orbi
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup
|
||||
endef
|
||||
|
||||
define Device/netgear_lbr20
|
||||
$(call Device/netgear_orbi)
|
||||
DEVICE_MODEL := LBR20
|
||||
NETGEAR_BOARD_ID := LBR20
|
||||
NETGEAR_HW_ID := 29766182+0+256+512+2x2+2x2+2x2+1
|
||||
KERNEL_SIZE := 7340032
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
|
||||
append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \
|
||||
append-ubi | netgear-dni
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
|
||||
append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | \
|
||||
append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-netgear_lbr20 ath10k-firmware-qca9888-ct kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
||||
endef
|
||||
TARGET_DEVICES += netgear_lbr20
|
||||
|
||||
define Device/netgear_rbx40
|
||||
$(call Device/netgear_orbi)
|
||||
NETGEAR_HW_ID := 29765515+0+4096+512+2x2+2x2+2x2
|
||||
|
||||
Loading…
Reference in New Issue
Block a user