mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-24 15:56:49 +00:00
07b9186e88
**Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem. SoC Type: Qualcomm IPQ4019 RAM: 512 MiB Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC) Bootloader: U-Boot Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink WiFi class AC2200: - radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels - radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz - radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on. Ethernet: 2x1GbE (WAN/LAN1, LAN2) LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white USB ports: No Buttons: 2 Reset and SYNC(WPS) Power: 12 VDC, 2,5 A Connector type: Barrel OpenWRT Installation 1. Simplest way is just do upgrade from webpage with *factory.img 2. You can also do it with standard tool for Netgear's debricking - NMPRFlash 3. Most advanced way is to open device , connect to UART console and : - Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10) - Connect serial console (115200,8n1) to UART connector - Connect TFTP server to RJ-45 port - Stop in u-Boot and run u-Boot command: > setenv serverip 192.168.1.10 > set fdt_high 0x85000000 > tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb > bootm 0x83000000 - Login via ssh - upload or download *sysupgrade.bin ( like wget ... or scp transfer) - Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”) Back to Stock - Download firmware from official Netgear's webpage , it will be *.img file after decompressing. - Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash ) Open the case - Unscrew nuts and remove washers from antenna's conectors. - There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it - Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that. - PCB is screwed with 4Pcs of Torx T10 screws - Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires) - On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg ) BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org. Signed-off-by: Marcin Gajda <mgajda@o2.pl>
82 lines
1.8 KiB
Plaintext
82 lines
1.8 KiB
Plaintext
#
|
|
# Copyright (C) 2016 LEDE
|
|
#
|
|
|
|
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
ubootenv_mtdinfo () {
|
|
UBOOTENV_PART=$(cat /proc/mtd | grep APPSBLENV)
|
|
mtd_dev=$(echo $UBOOTENV_PART | awk '{print $1}' | sed 's/:$//')
|
|
mtd_size=$(echo $UBOOTENV_PART | awk '{print "0x"$2}')
|
|
mtd_erase=$(echo $UBOOTENV_PART | awk '{print "0x"$3}')
|
|
nor_flash=$(find /sys/bus/spi/devices/*/mtd -name ${mtd_dev})
|
|
|
|
if [ -n "$nor_flash" ]; then
|
|
ubootenv_size=$mtd_size
|
|
else
|
|
# size is fixed to 0x40000 in u-boot
|
|
ubootenv_size=0x40000
|
|
fi
|
|
|
|
sectors=$(( $ubootenv_size / $mtd_erase ))
|
|
sectors=$(printf "0x%x" $sectors )
|
|
echo /dev/$mtd_dev 0x0 $ubootenv_size $mtd_erase $sectors
|
|
}
|
|
|
|
case "$board" in
|
|
alfa-network,ap120c-ac|\
|
|
devolo,magic-2-wifi-next|\
|
|
edgecore,ecw5211|\
|
|
glinet,gl-a1300 |\
|
|
glinet,gl-ap1300|\
|
|
glinet,gl-b1300|\
|
|
glinet,gl-b2200|\
|
|
luma,wrtq-329acn|\
|
|
netgear,wac510|\
|
|
openmesh,a42|\
|
|
openmesh,a62|\
|
|
pakedge,wr-1|\
|
|
plasmacloud,pa1200|\
|
|
plasmacloud,pa2200)
|
|
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
aruba,ap-303)
|
|
ubootenv_add_uci_config "/dev/mtd13" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
aruba,ap-365)
|
|
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
buffalo,wtr-m2133hp|\
|
|
netgear,lbr20)
|
|
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
linksys,ea6350v3)
|
|
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x20000" "0x20000"
|
|
;;
|
|
linksys,ea8300|\
|
|
linksys,mr8300)
|
|
ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x40000" "0x20000"
|
|
;;
|
|
linksys,whw01)
|
|
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x40000" "0x10000"
|
|
;;
|
|
linksys,whw03v2)
|
|
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x80000" "0x20000"
|
|
;;
|
|
zyxel,nbg6617)
|
|
ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config ubootenv
|
|
|
|
exit 0
|