Rebase local patches on top of quarterly timed release, allowing to
drop numerous patches which have been accepted upstream since the
release of U-Boot 2023.07.02.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If nodes /chosen/rootdisk-${bootdevice} exists, set /chosen/rootdisk
phandle according to boot device selected by the bootstrap pins.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When erasing large amounts of blocks at once this can take a long
time on slow cards. Instead of a fixed timeout, wait longer if more
blocks are being erased.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add basic U-Boot drop-in replacement compatible with the flash layout
of the vendor loader of the Zbtlink WG3526 (16M) MT7621 router board.
The idea here is a to have a reference build of uboot-mediatek also for
a simple MIPS boards more popular than MT7621 RFB.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make use of recently added UBI support in MediaTek's ARM
TrustedFirmware-A on new MT7988 SoC.
Load fip from static UBI volume instead of fixed offset on SPIM-NAND
and SNFI.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hide arm-trusted-firmware-mediatek packages from interactive config.
Exposing them only causes confusion and needed variants are anyway
selected as dependencies by uboot-mediatek packages.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
This reverts commit dcdcfc1511.
This is a firmware for third-party u-boot mod, which should not
be carried here by us.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Bump the U-Boot version used for BCM53xx to the 2024.01
version that includes all the needed patches upstream, so we
can get rid of those in the process.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linksys MX4200 is a 802.11ax Tri-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 512Mb NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* RGB system led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition
fw_printenv -n boot_part
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel
Replace (X) with your model version either 1 or 2
Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.
Specification:
- MT7622BV SoC with 2.4GHz wifi
- MT7975AN + MT7915AN for 5GHz
- MT7531BE Switch
- 512MB RAM
- 128 MB flash
- 2 LEDs (Status and Internet, both can be either orange or white)
- 2 buttons (WPS and Reset)
Compared to M32, the R32 has the following differences:
- 4 LAN ports instead of 2
- The recory image starts with DLK6E6015001 instaed of DLK6E6010001
- Individual LEDs for power and internet
- MAC address is stored at another offset in the ODM partition
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin
Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin
Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again
There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.
Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
- The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
- The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
- OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(based on support for ASUS RT-AX59U by liushiyou006)
SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Upgrade from AsusWRT to OpenWRT using UART
Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.
Connect the PC with TFTP server to the RT-AX59U.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.
Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax59u.bin
$ bootm 0x46000000
Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Upgrade from AsusWRT to OpenWRT using WebUI
Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq
Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file
Wait for OpenWRT to boot (192.168.1.1).
Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command
MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.
: Stock : OpenWrt
WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
WLAN 2g (2) : : CA:xx:xx:0D:xx:D4
WLAN 2g (3) : : CE:xx:xx:0D:xx:D4
WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
WLAN 5g (2) : : CE:xx:xx:1D:xx:D5
WLAN 5g (3) : : C2:xx:xx:1D:xx:D5
WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
WLAN 2g (2) : : 0A:xx:xx:76:xx:BE
WLAN 2g (3) : : 0E:xx:xx:76:xx:BE
WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
WLAN 5g (2) : : 0E:xx:xx:76:xx:BF
WLAN 5g (3) : : 02:xx:xx:76:xx:BF
Signed-off-by: Xavier Franquet <xavier@franquet.es>
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon@gmail.com>
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Power (green, unmanaged)
- 1x Status (green, gpio)
- 1x 2.4G (green, hardware, mt76-phy0)
- 1x 2.4G (blue, gpio)
- 1x 5G (green, hardware, mt76-phy1)
- 1x 5G (blue, gpio)
- 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (default http://192.168.0.1/)
under "admin" account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following block:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>
5. Replace <some value> by a new superadmin password and add a line
which enabling superadmin login after. For example, the block after
the changes:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The previous offsets did also work, as they've wrapped back to 0x0.
However, in reality the environment starts at offset 0x0 of the
u-boot-env MMC partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
SoC: MediaTek MT7981BA
RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC: 8GB eMMC (Samsung 8GTF4R)
ETH: 1000Base-T LAN (ePHY)
2500Base-T WAN (MaxLinear GPY211C)
BTN: 1x Reset Button
LED: System (blue/white)
VPN (white)
USB: 1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
Don't connect 3.3V!
Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!
Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
Currently there's no usable mainline (open source) TF-A implementation
for rk35xx SoCs, so pack the prebuilt firmware from the vendor.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender,
manufactured by Alpha Networks [8WAPAC28.1A1G].
(in square brackets: PCB silkscreen markings)
Specifications:
* CPU (Qualcomm Atheros QCA9563-AL3A [U5]):
775 MHz single core MIPS 74Kc;
* RAM (Winbond W9751G6KB-25J [U3]):
64 MiB DDR2;
* ROM (Winbond W25Q128FV [U16]):
16 MiB SPI NOR flash;
* Ethernet (AR8033-AL1A PHY [U1], no switch):
1 GbE RJ45 port (no PHY LEDs);
* Wi-Fi
* 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]):
3x3 802.11n;
* 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]):
3x3 802.11ac Wave 1;
* 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3];
* GPIO LEDs:
* RSSI low (red/green) [D2];
* RSSI medium (green) [D3];
* RSSI high (green) [D4];
* status (red/green) [D5];
* GPIO buttons:
* WPS [SW1], co-located with status LED;
* reset [SW4], accessible via hole in the side;
* Serial/UART:
Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch;
125000-8-n-1 in U-boot, 115200-8-n-1 in kernel;
* Misc:
* 12V VCC [JP2], fed from internal 12V/1A AC to DC converter;
* on/off slide switch [SW2] (disconnects VCC mechanically);
* unpopulated footprints for a Wi-Fi LED [D1];
* unpopulated footprints for a 4-pin 3-position slide switch (SW3);
MAC addresses:
* Label = LAN;
* 2.4 GHz WiFi = LAN;
* 5 GHz WiFi = LAN+2;
Installation:
* `factory.bin` can be used to install OpenWrt from OEM firmware via the
standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html
* `recovery.bin` can be used to install OpenWrt (or revert to OEM
firmware) from D-Link Web Recovery. To enter web recovery, keep reset
button pressed and then power on the device. Reset button can be
released when the red status LED is bright; it will then blink slowly.
Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and
upload 'recovery.bin'. Note that in web recovery mode the device
ignores ping and DHCP requests.
Note: 802.11s is not supported by the default `ath10k` driver and
firmware, but is supported by the non-CT driver and firmware variants.
The `-smallbuffers` driver variant is recommended due to RAM size.
Co-developed-by: Anthony Sepa <protectivedad@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
The ubootmod bootlaoder for EX5601-T0 uses two partitions
in ubi to store enviroment variables. so proper config
is needed.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Flash procedure is described in next commit.
TLDR:
Copy preloader and uboot to /tmp and write them in the mtd.
This will also require new UBI partition and
volumes to boot openwrt.
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Changelist:
- Added profile for 4k+256 SPI NAND_TYPE
- Added basic Zyxel EX5601-T0 uboot profile
Backported from hitech95 branch:
- Button RESET pin fix
- Button WPS pin fix
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 3cc57ba462 as it
should be fixed in commit 78cbd5a57e11 ("tools: macOS: types.h: fix
missing unsigned types").
References: #13833
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 997ff740dc.
78cbd5apick as it should be fixed in commit 78cbd5a57e11 ("tools: macOS:
types.h: fix missing unsigned types").
References: #13833
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It must read the entire image for previous code of 'imsz' or 'imszb'.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Suggested-by: Chuanhong Guo <gch981213@gmail.com>
Specifications:
SoC: QCA9531(650MHz)
RAM: DDR2 128M
Flash: SPI NOR 16M + SPI NAND 128M
WiFi: 2.4GHz with 2 antennas(WiFi/Thread)
Ethernet:
1xLAN(10/100M)
2xWAN(10/100M)
Button: 1x Reset Button
Switch: 1x Mode switch
LED: 1x Blue LED + 1x White LED + 1x Orange LED
IOT: Thread + ZigBee/Zwave
By uboot web failsafe:
Push the reset button for 5 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
Commit 572ea68070 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.
Fixes: #13724
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Furong Xu <xfr@outlook.com>
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
GND RXD TXD, beginning from the external antennas. 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet
Wlan:
* 4x4 in 2.4GHz : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)
Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A
Mounting: Wall and ceiling
```
```
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to the console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch
a new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global
priv->pll_clk_rate field. This will cause to have a reduced
clock rate on each subsequent SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
This is a partial revert of the deletion of the IXP4xx
target: we restore the APEX boot loader so we can use it
for the NSLU2 and related targets.
The APEX upstream is as dead as it gets so I have applied
OpenWrts old patches on top of the never released
v1.6.10 version and forked it into an OpenWrt variant
on GitHub. If the upstream comes back alive I will
happily switch over to it.
The file refers to the external GitHub, I suppose when
integrating this patch the file should be copied to OpenWrts
file repository and the file link changed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/
SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
4pin Serial Header | 3.3 | GND | RX | TX
MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env
* Installation via either RJ45 console or on-board 4 PIN header
Install Method
--------------
1) Setup TFTP server, and place
openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
(use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
set bootcmd 'ping 192.168.1.1; run boot_flash'
saveenv
8) TFTP image to RAM:
tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin
Signed-off-by: Glen Lee <g2lee@yahoo.com>
When adding new router support, I found that uboot
could not recognize flash: "unknown raw ID xxx".
Sync SPI-NAND driver for mediatek to fixes this:
* Add support for Winbond W25N01KV 1Gbit chip.
* Add support for Etron SPI-NAND chip.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
- detect die revision used in variants of the Allwinner H616 SoC (H313, T507)
- support for H6 boards without PMIC
Tested on Pine64+ and Orange PI Zero2
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
Use the header closest to LED 4 and 5.
They are marked with a white stroke.
TX RX GND, beginning from "4". 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)
Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)
Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```
```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When adding builds for MT7981 the related Makefile sections for MT7986
have apparently been copied, but in one instance the rename from 7986 to
7981 has been omitted. Fix that now.
Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
In order to use the same image for both boards, U-Boot is responsible for
detecting the revision and enabling/disabling DTS nodes.
So, to make it easy for users, lets add the pending U-Boot patches to build
in OpenWrt.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
With recent updates of TF-A the previously already fixed bug slipped
back into the source tree. Again, reorder bl2 init for MT7622 and
initialize WDT only after DRAM init has completed to avoid the
notorious hang.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board.
Add pre-built files to fix swig dependencies.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- USB Host:
1 x USB3.0 Type A HOST
1 x USB2.0 OTG (40-pin pin-header)
- Wireless:
RTL8723DU/RTL8821CU
- Power Supply: Type-C 5V
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Always enable built-in 2.5G PHY on MT7988 for now, so that it can be
used. In future it would be nice to be able to switch power and MDIO
access via address 0 at run-time in Linux, both, to be able to use
external PHYs at address 0 and to reduce power consumption on systems
not using the built-in 2.5G PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The U-Boot build for the MT7988 reference board booting from SD card
wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build
even though the 'comb' variant is used. Fix that dependency.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While the v2 is nearly identical to v1, v3 uses a different PHY and
needs a different build for Ethernet to work in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Select many potentially useful options for the MT7988 RFB U-Boot builds.
The resulting loader is intended as a development tool and intends to be
generic. It does *not* have a default bootcmd set, but allows to boot
pretty much everything, including EFI executables.
To install this U-Boot build to the eMMC:
opkg install mmc-utils partx-utils
mmc bootpart enable 1 1 /dev/mmcblk0
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0
partx -a /dev/mmcblk0
dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Compile-tested: all boards
Runtime-tested:
- Cortex-A8: pcDuino
- Cortex-A7: Bananapro, Bananapi M3
- Cortex-A53:Pine64+
Notes:
- binman tries to add firmware for the SCP (system control processor), which
we don't build, and is optional for the boot process on 64-bit. Disable this
via setting the SCP envvar to /dev/null. For further info, see [1] .
[1] https://github.com/u-boot/u-boot/blob/master/board/sunxi/README.sunxi64
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
We have to move to use git clone as there are no newer tagged releases.
Changes:
604f8f5 Default CROSS_CM3 to arm-none-eabi- instead of armv7m-softfloat-eabi-
b9b9419 Tidy up license information
0290b2c wtmi: Fix typo
a10b8e9 Makefile: fix a53-firmware.bin generation (maximum size is not optimal)
f654082 wtmi: Add const qualifier to isr_vector
4a43a3b wtmi: Improve detection of ESPRESSObin boards with Topaz
189e629 wtmi: Improve detection of boards with insufficient MDIO pull-up
3dac4fe wtmi: Fix detection of Armada 3720 Devel Board
3ca4dfa Bump mox-imager commit
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
1de442d Convert floating point operations to integer operations
ce6770d Modify mv_ddr4_calibration_validate function body to match function header
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
a3e1c67 wtmi: Fix linker output sections
f65e3bf wtmi: Remove usage of non-existant string.h file and memcpy() function
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Recent envtools update to 2023.07.02 has introduced a breakage when trying
to parallel build with the following error:
/bin/sh: line 1: scripts/basic/fixdep: No such file or directory
Luckily it can easily be reproduced locally via a simple script so it was
not hard to bisect it down to upstream commit [1].
However, its not that commits fault, it just uncovered an issue with the
way we have been building envtools for a long time, maybe even from the
package introduction.
The issue is that we are trying to build envtools as one of the U-Boot
no-dot-config-targets but envtools was newer a valid target for it but
since we were creating the config headers that were not actually used it
was actually building all this time.
Since the blamed commit [1] a tool called printinitialenv is built and
now a proper config is actually required in order for prerequisites to
get built properly.
So, in order to properly fix this (Hopefully for good) lets stop pretending
that envtools are a valid no-dot-config-targets target and use the
tools-only defconfig which is meant exactly for just building the tools.
This will make a minimal config for the U-Boot sandbox target and then
envtools will build just fine in parallel mode (I tested with 32 threads).
We do hovewer need to override the ARCH passed by OpenWrt and set it to
sandbox as otherwise U-Boot will not find the required headers because the
ARCH is being overriden to an incorrect one.
[1] 40b77f2a3a
Fixes: 9db0330052 ("uboot-envtools: update to 2023.07.02")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
WED requires a bunch of additional reserved memory regions. As U-Boot's
LMB allocator defaults to a maximum of only 8 regions, this currently
makes using WED impossible.
Raise LMB_MAX_REGIONS to 64 just like for all other MediaTek boards
with a SoC supporting WED.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.
Signed-off-by: Stefan Agner <stefan@agner.ch>
I recently added support for the NorthStar ARM BCM53xx SoCs
to the upstream U-Boot. This is a back port on top of the
2023.04 version already imported to OpenWrt with the 5 necessary
upstream patches.
This is needed to create a small U-Boot for the BCM53xx-based
D-Link DIR-890L and I think also the DIR-885L, so that a
recent (bigger) kernel can be loaded and executed from the
SEAMA partitions on these devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.
Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree
Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
refuses to boot if it doesn't. The chosen "rootfs" volume must contain
a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
variable to the label mac. But "factoryparams" does not always
exist. Instead there is a "RIP" volume containing all the factory
data. Copying the "RIP" volume to "factoryparams" will fix this
Hardware
--------
SOC: MediaTek MT7986
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI: Mediatek MT7986 802.11ax 5 GHz
Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.2/24. Rename the image to C0A80101.img.
2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
console, Interrupt the autoboot process by pressing ESC when prompted.
3. Download and boot the OpenWrt initramfs image.
$ env set uboot_bootcount 0
$ env set firmware nominal
$ tftpboot
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
not configured by OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.
The majority of the code is based on @jewwest's PR #11830.
Specifications:
* CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
* Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
* Wi-Fi:
* 2.4 GHz: Qualcomm QCN5024 4x4
* 2x 5 GHz: Qualcomm QCN5054 4x4
* USB: 2x USB 3.0
* LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
* Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
* UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
* Power: 19 VDC, 3.1 A
Installation:
* Flashing OpenWrt is done in two steps:
a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
This writes an initramfs based OpenWrt image onto the RAX120v2
b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline
* U-Boot allows booting an initramfs image via TFTP:
- Set ip of your PC to 192.168.1.100
- At the serial console interrupt boot at "Hit any key to stop autoboot:"
- In u-boot run `tftpsrv`
- On your PC send the OpenWrt initramfs image:
tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb
Make 5G Aquantia phy work:
For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
u-boot by writing the firmware to the correct mtd partition.
The firmware file found in the Netgear stock firmware under /lib/firmware/ named
'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
be converted to a MBN file.
The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
under 'git_home/u-boot.git/tools/mkheader.py'
Convert the CLD file to MBN using:
$ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn
This MBN file can then be flashed to the MTD partition to be used by u-boot.
The necessary files can also be found in
https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware
* Write MBN file to MTD partition to be loaded automatically by u-boot:
U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
corresponds to `/dev/mtd25` in OpenWrt.
- find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)
$ fgrep -i 'ethphyfw' /proc/mtd
mtd25: 00080000 00020000 "ethphyfw
- copy mbn file to /tmp/ folder of the router
$ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/
- write mbn file to ethphyfw partition
$ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to RAX120v2 GPL source:
https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
Update to the latest stable version.
This update changes the default lockfile directory from /var/lock to
/run [1]. In OpenWRT we still use the "legacy" /var/lock and /run might
not even exist, so we add a patch to revert this particular change.
[1] aeb40f1166
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Instead of reading only a single 4kiB page, read the first 128kiB to
determine the size of an uImage.FIT using 'imsz' or 'imszb'.
This will be needed once we add more Device Tree Overlays, which may
happen for the BPi-R3 mini.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to fix build failure caused by a missing header which had
previously been implicitely included.
Fixes: 6ddb5f5a65 ("uboot-mediatek: update to version 2023.07.02")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Among the patches adding support for MT7988 also came the switch to
use fdtdec_setup_mem_size_base() and no longer rely on CFG_SYS_SDRAM_BASE.
Take care of our downstream boards which did not have a 'memory' node in
their device trees.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of using the hash of the Github-generated tarball use the
hash of the tarball generated by the OpenWrt build system (in this
case they are different, unfortunately).
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: 07dbeb430e ("arm-trusted-firmware-mediatek: update to sources of 2023-07-24")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import pending patches adding support for MT7988 and provide builds
for the reference board for all possible boot media.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Release 2023.07 got tagged wrongly and replaced by follow-up release
2023.07.02.
Now using upstream DTS for BPi-R3.
Removed two patches which made it upstream, refreshed the rest.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use updated Trusted Firmware-A sources from MediaTek, now stacked
on top of the ARM Trusted Firmware-A v2.9 release.
Add builds for the newly added MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since 2021.07 multiple bugs were introduced that made it impossible to
create a bootable target for mvebu. Those issues should be now fixed since
2023.07-rc1.
References: #11661
Signed-off-by: Oli Ze <olze@trustserv.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs
Signed-off-by: Petr Štetiar <ynezz@true.cz> [facelift]
Because this device enable NMBM by default, most users use custom
U-Boot with NMBM-Enabled in Chinese forums.
This layout is the same as the ubootmod layout but enabling NMBM.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
This is the first commit to introduce the base for the N821 board used
in Cisco vEdge 1000.
This commit does not include the custom CPLD drivers but rather
everything else that is already present in the upstream kernel.
This results in an image that boots, but e.g. the SFP ports are not
usable.
Hardware:
- CPU: Cavium Networks CN6130, 4 cores @ 1.0 GHz
- Flash:
- 16 MiB SPI NOR presented as 2x8 MiB for A/B boot recovery
- 8192 MiB eMMC
- RAM: 4096 MiB
- Ethernet 1Gbit ports: 1x
- Ethernet SFP ports: 8x
- USB ports: 2x 3.0 Type-A on front panel
- Serial: Two, one internal and one external
- JTAG: Yes
- LED count: 18x
- Button count: 1x
- GPIOs: 1x
- Power: 2x redundant DC 12V barrel plug
- Extra: Slot for SD card on front
See the OpenWrt wiki for more hardware details.
Installation:
- Flash squashfs to /dev/sda2 and put kernel on /dev/sda1.
- Update uboot's bootcmd environment variable to match.
Full installation guide will be added to OpenWrt wiki when sysupgrade
support is added.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Tommy Nevtelen <tommy@nevtelen.com>
Tested-by: Viktor Ekmark <viktor@ekmark.se>
Tested-by: Daniel Wennberg <github@networkninja.se>
The side-effect and main motivation is to also drop the FIT structure size
limit because with multiple device tree overlays it may easily grow beyond
the previous 4kB limit in the future.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ASUS RT-AC59U / RT-AC59U v2 are wi-fi routers with a large number of
alternate names, including RT-AC1200GE, RT-AC1300G PLUS, RT-AC1500UHP,
RT-AC57U v2/v3, RT-AC58U v2/v3, and RT-ACRH12.
ASUS ZenWiFi AC Mini(CD6) is a mesh wifi system. The unit labeled CD6R
is the router, and CD6N is the node.
Hardware:
- SoC: QCN5502
- RAM: 128 MiB
- UART: 115200 baud (labeled on boards)
- Wireless:
- 2.4GHz: QCN5502 on-chip 4x4 802.11b/g/n
currently unsupported due to missing support for QCN550x in ath9k
- 5GHz: QCA9888 pcie 5GHz 2x2 802.11a/n/ac
- Flash: SPI NOR
- RT-AC59U / CD6N: 16 MiB
- RT-AC59U v2 / CD6R: 32 MiB
- Ethernet: gigabit
- RT-AC59U / RT-AC59U v2: 4x LAN 1x WAN
- CD6R: 3x LAN 1x WAN
- CD6N: 2x LAN
- USB:
- RT-AC59U / RT-AC59U v2: 1 port USB 2.0
- CD6R / CD6N: none
WiFi calibration data contains valid MAC addresses.
The initramfs image is uncompressed because I was unable to boot a
compressed initramfs from memory (gzip or lzma). Booting a compressed
image from flash works fine.
Installation:
To install without opening the case:
- Set your computer IP address to 192.168.1.10/24
- Power up with the Reset button pressed
- Release the Reset button after about 5 seconds or until you see the
power LED blinking slowly
- Upload OpenWRT factory image via TFTP client to 192.168.1.1
Revert to stock firmware using the same TFTP method.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
This commit adds support for following wireless routers:
- Beeline SmartBox PRO (Serсomm S1500 AWI)
- WiFire S1500.NBN (Serсomm S1500 BUC)
This commit is based on this PR:
- Link: https://github.com/openwrt/openwrt/pull/4770
- Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.
My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1
Common specification
--------------------
SoC: MediaTek MT7621AT (880 MHz, 2 cores)
Switch: MediaTek MT7530 (via SoC MT7621AT)
Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe: via J2 on PCB, not soldered on the board
UART: J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek
Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1
WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1
MAC address table (PRO)
-----------------------
use address source
LAN *:23 factory 0x1000 (label)
WAN *:24 factory $label +1
2g *:23 factory $label
5g *:25 factory $label +2
MAC addresses (NBN)
-------------------
use address source
LAN *:0e factory 0x1000
WAN *:0f LAN +1 (label)
2g *:0f LAN +1
5g *:10 LAN +2
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
a. OpenWrt - that's OK, the mission accomplished
b. Stock firmware - install Stock firmware (to switch booflag from
Sercomm0 to Sercomm1) and then OpenWrt factory image.
Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
reboot
2. Install stock firmware via the web OEM firmware interface
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.
Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).
It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.
Related: https://github.com/openwrt/openwrt/pull/5084
For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.
Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
boot, then hold the reset button for 10 seconds. This is needed
because sysupgrade in the stock firmware will attempt to preserve its
configuration using sysupgrade.tgz.
See https://github.com/openwrt/openwrt/pull/4182
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.
Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
All LEDs and buttons appear to work without state_default.
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz
* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
DTS file for this device.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Migrate to "new" image generation method. Device profiles will be generated
based on image/Makefile instead of profiles/ , which will also allow to
automatically build images for all supported devices via buildbot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
rk3399 ATF requires arm toolchain to build the m0 pmu driver.
As OpenWrt doesn't ship this toolchain so download the prebuilt one
just like what we did in arm-trusted-firmware-mvebu.
Fixes: 5d1cb52da0 ("arm-trusted-firmware-rockchip: Update to 2.9")
Reported-by: Wurzer Juergen <wurzer.juergen@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
General specification:
SoC Type: MediaTek MT7620A (580MHz)
ROM: 8 MB SPI-NOR (MX25L6406E)
RAM: 64 MB DDR (W9751G6KB-25)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Wireless: 5 GHz (MediaTek MT7610EN): ac/n
Buttons: 2 button (POWER, WPS/RESET)
Bootloader: U-Boot 1.1.3
Power: 12 VDC, 0.5 A
MACs:
| LAN | [Factory + 0x04] - 2 |
| WLAN 2.4g | [Factory + 0x04] - 1 |
| WLAN 5g | [Factory + 0x8004] - 3 |
| WAN | [Factory + 0x04] - 2 |
OEM easy installation:
1. Use a PC to browse to http://192.168.0.1.
2. Go to the System section and open the Firmware Update section.
3. Under the Local Update at the right, click on the CHOOSE FILE...
4. When a modal window appears, choose the firmware file and click on
the Open.
5. Next click on the UPDATE FIRMWARE button and upload the firmware image.
Wait for the router to flash and reboot.
OEM installation using the TFTP method (need level converter):
1. Download the latest firmware image.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware
image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect the PC
to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address 192.168.0.180
and subnet mask 255.255.255.0.
5. Connect serial port (57600 8N1) and turn on the router.
6. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load
system code then write to Flash via TFTP.").
7. Press Y key when show "Warning!! Erase Linux in Flash then burn new
one. Are you sure? (Y/N)"
Input device IP (192.168.0.1) ==:192.168.0.1
Input server IP (192.168.0.180) ==:192.168.0.180
Input Linux Kernel filename () ==:firmware_name
The router should download the firmware via TFTP and complete flashing in
a few minutes.
After flashing is complete, use the PC to browse to http://192.168.1.1 or
ssh to proceed with the configuration.
Signed-off-by: Alexey Bartenev <41exey@proton.me>
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.
See the online manual for more information, including the
flash layout[2].
This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.
We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
Device specifications:
======================
* Qualcomm/Atheros AR9344
* 128 MB of RAM
* 16 MB of SPI NOR flash
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4/5 GHz Wi-Fi
* 4x GPIO-LEDs (1x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* 2x fast ethernet
- lan1
+ builtin switch port 1
+ used as WAN interface
- lan2
+ builtin switch port 2
+ used as LAN interface
* 9-30V DC
* external antennas
Flashing instructions:
======================
Log in to https://192.168.127.253/
Username: admin
Password: moxa
Open Maintenance > Firmware Upgrade and install the factory image.
Serial console access:
======================
Connect a RS232-USB converter to the maintenance port.
Pinout: (reset button left) [GND] [NC] [RX] [TX]
Firmware Recovery:
==================
When the WLAN and SYS LEDs are flashing, the device is in recovery mode.
Serial console access is required to proceed with recovery.
Download the original image from MOXA and rename it to 'awk-1137c.rom'.
Set up a TFTP server at 192.168.127.1 and connect to a lan port.
Follow the instructions on the serial console to start the recovery.
Signed-off-by: Maximilian Martin <mm@simonwunderlich.de>
This commit adds support for Mercusys MR90X(EU) v1 router.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled
LEDs on ethernet ports
Button: 1 (Reset)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
The R3 (TX line) and R6 (RX line) are absent on the PCB. You should
solder them or solder the jumpers.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Once inside OpenWrt, set / update env variables:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial@11002000
fw_setenv stdin serial@11002000
fw_setenv stdout serial@11002000
fw_setenv tp_boot_idx 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Installation (without UART)
---------------------------
1. Login as root via SSH (router IP, port 20001, password - your web
interface password)
2. Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and
SSH settings from the p.1)
3. Add a newline after "#!/bin/sh":
telnetd -l /bin/login.sh
4. Save "65-iptv" file
5. Toggle "IPTV/VLAN Enable" checkbox in the router web interface and
save
6. Make sure that telnetd is running:
netstat -ltunp | grep 23
7. Login via telnet to router IP, port 23 (no username and password are
required)
8 Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the
router (e.g., using WinSCP and SSH settings from the p.1)
9. Stock busybox doesn't contain ubiupdatevol command. Hence, we need to
download and upload the full version of busybox to the router. For
example, from here:
https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64
Upload busybox-arm64 to the /tmp dir of the router and run:
in the telnet shell:
cd /tmp
chmod a+x busybox-arm64
10. Check "initramfs-kernel.bin" size:
du -h initramfs-kernel.bin
11. Delete old and create new "kernel" volume with appropriate size
(greater than "initramfs-kernel.bin" size):
ubirmvol /dev/ubi0 -N kernel
ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB
12. Write OpenWrt "initramfs-kernel.bin" to the flash:
./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin
13. u-boot-env can be empty so lets create it (or overwrite it if it
already exists) with the necessary values:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial@11002000
fw_setenv stdin serial@11002000
fw_setenv stdout serial@11002000
fw_setenv tp_boot_idx 0
14. Reboot to OpenWrt initramfs:
reboot
15. Login as root via SSH (IP 192.168.1.1, port 22)
16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
17. Run sysupgrade:
sysupgrade -n /tmp/sysupgrade.bin
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery (UART)
---------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Do what you need (restore partitions from a backup, install OpenWrt
etc.)
Stock layout
------------
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format
----------------
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 00:eb:xx:xx:xx:be | label |
| LAN | 00:eb:xx:xx:xx:be | label |
| WAN | 00:eb:xx:xx:xx:bf | label+1 |
| WLAN 2g | 00:eb:xx:xx:xx:be | label |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac". OEM wireless eeprom is also there (file
"MT7986_EEPROM.bin").
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Hardware
========
CPU Qualcomm Atheros QCA9558
RAM 256MB DDR2
FLASH 2x 16M SPI-NOR (Macronix MX25L12805D)
WIFI Qualcomm Atheros QCA9558
Atheros AR9590
Installation
============
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x80060000 ap115.bin; go 0x80060000"
$ setenv fb_openwrt "bank 1;
cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000"
$ setenv bootcmd "run fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
SOC: MediaTek MT7986
RAM: 1024MB DDR3
FLASH: 128MB SPI-NAND (Winbond)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the WAX220. Conect to the serial console,
interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.2.1
$ setenv serverip 192.168.2.2
$ tftpboot openwrt.bin
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Now that qualcommax exists as a target and dependencies have been updated
let move ipq807x support to subtarget of qualcommax.
This is mostly copy/paste with the exception of having to update SSDK and
NSS-DP to use CONFIG_TARGET_SUBTARGET.
This is a preparation for later addition of IPQ60xx and IPQ50xx support.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s.
However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s
and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid
duplicating kernel patches and everything lets make a common target with
per SoC subtargets.
Start doing that by renaming ipq807x to qualcommax so that dependencies
on ipq807x target can be updated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
The armvirt target has been renamed to armsr (Arm SystemReady),
so the GRUB configuration also needs to change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This commit add u-boot env config for GL-MT3000, so
that we can use fw_printenv to print u-boot env and
use fw_setenv to set u-boot env in GL-MT3000.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Update bootloader environment for BPi-R3 and BPi-R64 to adapt to new
device tree overlay mechanism now that support for multiple device
tree overlays has been added.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds a separate package for EFI on Arm SystemReady
compatible machines. 32-bit Arm UEFI is supported as well.
It is very similar to x86-64 EFI setup, without the
need for BIOS backward compatibility and slightly
different default modules.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Add support for the Xunlong Orange Pi R1 Plus LTS.
Manually generated of-platdata files to avoid swig dependency.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Add support for the Xunlong Orange Pi R1 Plus.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
At this moment loadaddr in most layerscape boards are configured to
0x81000000. 5.15 kernel on some boards is bigger than 5.10 and it cause error:
Loading kernel from FIT Image at 81000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.112
Created: 2023-05-21 17:39:35 UTC
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x810000ec
Data Size: 7513944 Bytes = 7.2 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x80000000
Entry Point: 0x80000000
Hash algo: crc32
Hash value: 6fd69550
Hash algo: sha1
Hash value: ee34c753ffb615e199a428762824ad4a0aaef90a
Verifying Hash Integrity ... crc32+ sha1+ OK
Loading fdt from FIT Image at 81000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt fsl_ls1088a-rdb-sdboot device tree blob
Created: 2023-05-21 17:39:35 UTC
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8172a98c
Data Size: 19794 Bytes = 19.3 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 59792ba3
Hash algo: sha1
Hash value: 135585a49f86cd85acea559b78b0098ae99d5e12
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8172a98c
Uncompressing Kernel Image
ERROR: new format image overwritten - must RESET the board to recover
resetting ...
This patch changes loadaddr to 0x88000000 (like LS1012A-FRDM board) to
avoid overlapping for bigger images (like initramfs) too.
Tested-by: Alexandra Alth <alexandra@alth.de> [LS1088ARDB]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Add new package for building bootloader for the SiFive U-series boards. Supported
boards at this stage are the HiFive Unleashed and HiFive Unmatched.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
OpenSBI is a form of a first-stage bootloader, which initializes
certain parts of an SoC and then passes on control to the second
stage bootloader i.e. an u-boot image.
We're introducing the package with release v1.2, which provides
SBI v0.3 and the SBI SRST extensions which helps to gracefully
reboot/shutdown various HiFive-U SoCs.
Tested on SiFive Unleashed and Unmatched boards.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add new build option BOARD_QFN/BOARD_BGA.
This option is only useful for MT7981 device.
MT7981A/B: BOARD_BGA, MT7981C: BOARD_QFN.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Add reserved memory for pstore/ramoops to device tree used by Linux
as well as U-Boot.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Compex WPQ873 is a development board with two M.2 B-key
slots for cellular modems.
Device info:
- IPQ8072A SoC
- 512MiB RAM
- 256MiB NAND flash
- 8MiB SPI NOR
- 3x 1GigE ports
- 1x 2.5GigE port
- 2.4GHz/5GHz AX WLAN
- 1x USB 3.0 port
- 1x M.2 B-key socket with PCIe 3.0
- 1x M.2 B-key socket with PCIe 2.0 and USB 3.0
- 4x SIM card slots
- Bluetooth LE 5.0 (QCA4024)
Prerequisites
1) TFTP server
2) 3.3V USB to TTL cable for UART console
2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it
TTL connector pinout: 2=TX, 3=RX, 4=GND
Arrow marks pin 1 which is 3.3V
Serial port settings: 115200 8N1 no flow control
The device will most likely ship with a QSDK-based firmware.
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server, for example:
`setenv serverip 192.168.1.10`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Afterwards, you can use sysupgrade to flash new OpenWRT images.
Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
A missing '\' caused the remaining parameters not to be passed to make.
This fixes the following error:
| gcc -c [...] fiptool.c -o fiptool.o
| In file included from fiptool.h:16,
| from fiptool.c:19:
|fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory
| 19 | # include <openssl/sha.h>
| | ^~~~~~~~~~~~~~~
|compilation terminated.
|make[3]: *** [Makefile:58: fiptool.o] Error 1
as the HOST_CFLAGS are no longer passed.
then, HOST_CFLAGS is specified as a command argument, this
is a specific problem of our built since appending these
needs the override directive.
Fixes: df28bfe03247 ("tfa-layerscape: Change to github and use the latest tag")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of tfa-layerscape has been changed from
codeuaurora to github. Also use the latest tag for Layerscape
Linux Development POC from NXP.
v2:
* restored ls1021a-afrdm board
* added platform defines to fiptool so ls-ddr-phy can be built
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of uboot-layerscape has been changed
from codeuaurora to github. Also use the latest tag for
Layerscape Linux Development POC from NXP.
Tested on:
* NXP FRWY-LS1012A
* NXP LS1028A-RDB
* NXP LS1046A-RDB
V2: Remove ls1028ardb specifix fixups not needed with new uboot
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add support for the FriendlyARM NanoPi R2C.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Instead of adding these common variables again and again simply create a
shared set for each SoC.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 16 MB (Macronix MX25L12835FM2I-10G)
- RAM: 128 MB (Nanya NT5CC64M16GP-DI)
- WLAN 2.4 GHz: 2x2 MediaTek MT7603EN
- WLAN 5 GHz: 2x2 MediaTek MT7615N
- Ethernet: 1x 10/100/1000 Mbps
- LED: Power, Wifi, WPS
- Button: Reset, WPS
- UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port)
Serial console @ 57600,8n1
Flash instructions:
Connect to serial console and start up the device. As the bootloader got
locked you need to type in a password to unlock U-Boot access.
When you see the following output on the console:
relocate_code Pointer at: 87f1c000
type in the super secure password:
1234567890
Then select TFTP boot from RAM by selecting option 1 in the boot menu.
As Linksys decided to leave out a basic TFTP configuration you need to
set server- & client ip as well as the image filename the device will
search for. You need to use the initramfs openwrt image for the TFTP
boot process.
Once openwrt has booted up, upload the sysupgrade image via scp and run
sysupgrade as normal.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Add support for the Firefly ROC-RK3328-CC.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Support uboot for NXP LS1028ARDB reference board. GIC V3 has to
be disabled in the uboot config to allow booting upstream kernels.
This patch can be dropped once uboot is updated to 2022.04 version
to nxp-qoriq github lf-6.1.1 branch.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
There seems to be a difference in firmware calling convention
between upstream and NXP kernels. On some cpus like ls1028
it will hang on firmware secure get random when using LF uboot
with upstream kernel. Instead of commenting it out, don't call
get radnom seed when "kaslr-seed" is not present in device tree.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
The image_header_t typedef has been removed from
uboot v2023.01 [1], replaced with legacy struct.
[1] f3543e6944
Fixes: 3d5c542 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
CONFIG_SYS_TEXT_BASE has been renamed to CONFIG_TEXT_BASE
in uboot v2023.01 [1], fixes all this variable.
[1] 984639039f
Fixes: 3d5c5427 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.
Specifications
==============
SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)
MAC address assignment
======================
The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.
The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.
Installation (web interface)
============================
The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.
The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.
1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy
NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.
Installation (UART method)
==========================
The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:
1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation
Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:
nand read 1800000 53c0000 800
mw.b 1800004 1 1
nand erase 53c0000 800
nand write 1800000 53c0000 800
This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.
Back to stock
=============
It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.
It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:
mtd write zyxel.bin Kernel2
echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
The Alcatel HH40V is a CAT4 LTE router used by various ISPs.
Specifications
==============
SoC: QCA9531 650MHz
RAM: 128MiB
Flash: 32MiB SPI NOR
LAN: 1x 10/100MBit
WAN: 1x 10/100MBit
LTE: MDM9607 USB 2.0 (rndis configuration)
WiFi: 802.11n (SoC integrated)
MAC address assignment
======================
There are three MAC addresses stored in the flash ROM, the assignment
follows stock. The MAC on the label is the WiFi MAC address.
Installation (TFTP)
===================
1. Connect serial console
2. Configure static IP to 192.168.1.112
3. Put OpenWrt factory.bin file as firmware-system.bin
4. Press Power + WPS and plug in power
5. Keep buttons pressed until TFTP requests are visible
6. Wait for the system to finish flashing and wait for reboot
7. Bootup will fail as the kernel offset is wrong
8. Run "setenv bootcmd bootm 0x9f150000"
9. Reset board and enjoy OpenWrt
Installation (without UART)
===========================
Installation without UART is a bit tricky and requires several steps too
long for the commit message. Basic steps:
1. Create configure backup
2. Patch backup file to enable SSH
3. Login via SSH and configure the new bootcmd
3. Flash OpenWrt factory.bin image manually (sysupgrade doesn't work)
More detailed instructions will be provided on the Wiki page.
Tested by: Christian Heuff <christian@heuff.at>
Signed-off-by: Andreas Böhler <dev@aboehler.at>
TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build
for replacement loader for both TL-XDR6086 and TL-XDR6088. The only
difference at U-Boot level is the different filename requested via
TFTP, matching the corresponding OpenWrt build artifacts for each
device.
The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088
except for the wireless part. Also create a uboot for the TP-Link
TL-XDR4288.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[rebase to uboot 23.04, correct led and button]
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
U-Boot commit ea6fdc13595 ("dm: button: add support for linux_code in
button-gpio.c driver") makes it mandatory to specify linux,code for all
buttons. As that broke handling of the reset button in U-Boot with the
update to U-Boot 2023.04, add linux,code for all butons.
Reported-by: @DragonBluep
Fixes: 50f7c5af4a ("uboot-mediatek: update to v2023.04")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Updating to U-Boot 2023.04 broke the build for the RAVPower RP-WD009
MT7628 board. This was due to upstream conversion of CONFIG_* to CFG_*
which was not applied to our downstream patch adding support for the
RAVPower RP-WD009 device.
Apply CONFIG_* to CFG_* converion analog to what has been done also
for mt7928_rfb upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update to next U-Boot timed release.
Remove now obsolete patch
100-01-board-mediatek-add-more-network-configurations.patch
Default IP addresses are now dealt with in Kconfig, no longer in board-
specific C header files.
Add patches to restore ANSI support in bootmenu which was broken upstream,
always use high-speed mode on serial UART for improved stability and fix
an issue with pinconf not being applied on MT7623 resulting in eMMC
being inaccessible when booting from micro SD card.
In order to keep the size of the bootloader on MT7623 below 512kB remove
some unneeded commands on both MT7623 boards.
Tested on:
* BananaPi BPi-R2 (MT7623N)
* BananaPi BPi-R3 (MT7986A)
* BananaPi BPi-R64 (MT7622A)
* Linksys E8450 (MT7622B)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SoC: NXP P1010 (1x e500 @ 800MHz)
RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9)
FLASH: 32M NOR (Spansion S25FL256S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035)
UART: 115200 8N1 (RJ-45 Cisco)
Installation
------------
1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in
the root directory of a TFTP server and serve it at
192.168.1.66/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Alter the bootcmd in U-Boot:
$ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm"
$ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000;
bootm 0x2000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
4. Boot the initramfs image
$ run ramboot_openwrt
5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install
using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: David Bauer <mail@david-bauer.net>
Use latest release build instead of a git snapshot. As this tarball
extracts in a trusted-firmware-a-2.8 subdirectory, we no longer need to
override the PKG_NAME defined in trusted-firmware-a.mk. The actual
package name is still the same, so we don't need to update any
dependencies.
Tested on A64-OLinuXino-1Ge16GW.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is the newest release where 210-sunxi-deactivate-binman.patch still
applies.
Tested on A64-Olinuxino-eMMC.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
General specification:
SoC Type: MediaTek MT7620N (580MHz)
ROM: 8 MB SPI-NOR (W25Q64FV)
RAM: 64 MB DDR (EM6AB160TSD-5G)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Buttons: 3 button (POWER, RESET, WPS)
Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT)
Bootloader: U-Boot 1.1.3
Power: 9 VDC, 0.6 A
MAC in stock:
|- + |
| LAN | RF-EEPROM + 0x04 |
| WLAN | RF-EEPROM + 0x04 |
| WAN | RF-EEPROM + 0x28 |
OEM easy installation
1. Use a PC to browse to http://my.keenetic.net.
2. Go to the System section and open the Files tab.
3. Under the Files tab, there will be a list of system
files. Click on the Firmware file.
4. When a modal window appears, click on the Choose File
button and upload the firmware image.
5. Wait for the router to flash and reboot.
OEM installation using the TFTP method
1. Download the latest firmware image and rename it to
klite3_recovery.bin.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the
firmware image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect
the PC to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address
192.168.1.2 and subnet mask 255.255.255.0.
5. Power up the router while holding the reset button pressed.
6. Wait approximately for 5 seconds and then release the
reset button.
7. The router should download the firmware via TFTP and
complete flashing in a few minutes.
After flashing is complete, use the PC to browse to
http://192.168.1.1 or ssh to proceed with the configuration.
Signed-off-by: Alexey Bartenev <41exey@proton.me>
This board is very similar to the Aruba AP-105, but is
outdoor-first. It is very similar to the MSR2000 (though certain
MSR2000 models have a different PHY[^1]).
A U-Boot replacement is required to install OpenWrt on these
devices[^2].
Specifications
--------------
* Device: Aruba AP-175
* SoC: Atheros AR7161 680 MHz MIPS
* RAM: 128MB - 2x Mira P3S12D40ETP
* Flash: 16MB MXIC MX25L12845EMI-10G (SPI-NOR)
* WiFi: 2 x DNMA-H92 Atheros AR9220-AC1A 802.11abgn
* ETH: IC+ IP1001 Gigabit + PoE PHY
* LED: 2x int., plus 12 ext. on TCA6416 GPIO expander
* Console: CP210X linking USB-A Port to CPU console @ 115200
* RTC: DS1374C, with internal battery
* Temp: LM75 temperature sensor
Factory installation:
- Needs a u-boot replacement. The process is almost identical to that
of the AP105, except that the case is easier to open, and that you
need to compile u-boot from a slightly different branch:
https://github.com/Hurricos/u-boot-ap105/tree/ap175
The instructions for performing an in-circuit reflash with an
SPI-Flasher like a CH314A can be found on the OpenWrt Wiki
(https://openwrt.org/toh/aruba/ap-105); in addition a detailed guide
may be found on YouTube[^3].
- Once u-boot has been replaced, a USB-A-to-A cable may be used to
connect your PC to the CP210X inside the AP at 115200 baud; at this
point, the normal u-boot serial flashing procedure will work (set up
networking; tftpboot and boot an OpenWrt initramfs; sysupgrade to
OpenWrt proper.)
- There is no built-in functionality to revert back to stock firmware,
because the AP-175 has been declared by the vendor[^4] end-of-life
as of 31 Jul 2020. If for some reason you wish to return to stock
firmware, take a backup of the 16MiB flash before flashing u-boot.
[^1]: https://github.com/shalzz/aruba-ap-310/blob/master/platform/bootloader/apboot-11n/include/configs/msr2k.h#L186
[^2]: https://github.com/Hurricos/u-boot-ap105/tree/ap175
[^3]: https://www.youtube.com/watch?v=Vof__dPiprs
[^4]: https://www.arubanetworks.com/support-services/end-of-life/#product=access-points&version=0
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Ruckus ZoneFlex 7363 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point. ZoneFlex 7343 is the single band variant of 7363
restricted to 2.4GHz, and ZoneFlex 7341 is 7343 minus two Fast Ethernet
ports.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet 1: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Ethernet 2: two Fast Ethernet ports through Realtek RTL8363S switch,
connected with Fast Ethernet link to CPU.
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the -U variants.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single PH1 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed.
Use the Gigabit interface, Fast Ethernet ports are not supported
under U-boot:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7363-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7363_fw_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7363-squashfs-sysupgrade.bin
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7363_backup.bin
4. System will reboot.
Quirks and known issues:
- Fast Ethernet ports on ZF7363 and ZF7343 are supported, but management
features of the RTL8363S switch aren't implemented yet, though the
switch is visible over MDIO0 bus. This is a gigabit-capable switch, so
link establishment with a gigabit link partner may take a longer time
because RTL8363S advertises gigabit, and the port magnetics don't
support it, so a downshift needs to occur. Both ports are accessible
at eth1 interface, which - strangely - runs only at 100Mbps itself.
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Ruckus ZoneFlex 7351 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the 7351-U variant.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7351-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7351_fw_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7351-squashfs-sysupgrade.bin
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7351_backup.bin
4. System will reboot.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This reduces open coding and allows to easily add a knob to
enable it treewide, where chosen packages can still opt-out via
"no-gc-sections".
Note: libnl, mbedtls and opkg only used the CFLAGS part without the
LDFLAGS counterpart. That doesn't help at all if the goal is to produce
smaller binaries. I consider that an accident, and this fixes it.
Note: there are also packages using only the LDFLAGS part. I didn't
touch those, as gc might have been disabled via CFLAGS intentionally.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall
or ceiling mountable. It can be powered via PoE, or a 12 V adapter.
The board has footprints for 2.54mm UART headers. They're difficult to
solder because the GND is connected to a large copper plane. Only try
soldering if you are very skilled. Otherwise, use pogo pins.
Specifications:
---------------
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 366 MB of RAM available to OS, not sure of total amount
* Storage: Macronix MX30UF2G18AC 256MB NAND
* Ethernet:
* 2.5G RJ45 port (QCA8081) with PoE input
* WLAN:
* 2.4GHz/5GHz with 8 antennas
* LEDs:
* Power (Amber)
* LAN (Blue)
* 2G WLAN (Blue)
* 5G WLAN (Blue)
* Buttons:
* 1x Factory reset
* Power: 12V DC Jack
* UART: Two 4-pin unpopulated headers near the LEDs
* "J2 UART" is the CPU UART, 3.3 V level
Installation:
=============
Web UI method
-------------
Flashing OpenWRT using the vendor's Web UI is problematic on this
device. The u-boot mechanism for communicating the active rootfs is
antiquated and unreliable. Instead of setting the kernel commandline,
it relies on patching the DTS partitions of the nand node. The way
partitions are patched is incompatible with newer kernels.
Newer kernels use the SMEM partition table, which puts "rootfs" on
mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One
reliable way to boot from mtd14 and avoid boot loops is to use an
initramfs image.
1. In the factory web UI, navigate to System Manager -> Firmware.
2. In the "Local Firmware Upgrade" section, click Browse
3. Navigate and select the 'web-ui-factory.fit' image
4. Click "Upload"
5. On the following page, click on "Proceed"
The flash proceeds at this point and the system will reboot
automatically to OpenWRT.
6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline
SSH method
----------
Enable SSH using the CLI or Web UI. The root account is locked out to
ssh, and the admin account defaults to Netgear's CLI application.
So we need to get creative:
First, make sure the device boots from the second firmware partition:
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 1
Then reboot the device, and run the update:
scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \
-o hostkeyalgorithms=ssh-rsa \
netgear_wax218-squashfs-nand-factory.ubi \
admin@<ipaddr>:/tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 0
Now reboot the device, and it should boot into a ready-to-use OpenWRT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
Hardware
--------
SoC: Freescale P1010
RAM: 512MB
FLASH: 1 MB SPI-NOR
512 MB NAND
ETH: 3x Gigabite Ethernet (Atheros AR8033)
SERIAL: Cisco RJ-45 (115200 8N1)
RTC: Battery-Backed RTC (I2C)
Installation
------------
1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI
programmer. The SHA1 hash for the U-Boot password is currently
unknown.
A tool for patching U-Boot is available at
https://github.com/blocktrron/t10-uboot-patcher/
You can also patch the unknown password yourself. The SHA1 hash is
E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA
2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears.
The patched password is '1234' (without quotation marks)
3. Download the OpenWrt initramfs image. Copy it to a TFTP server
reachable at 10.0.1.13/24 and rename it to uImage.
4. Connect the TFTP server to ethernet port 0 of the Watchguard T10.
5. Download and boot the initramfs image by entering "tftpboot; bootm;"
in U-Boot.
6. After OpenWrt booted, create a UBI volume on the old data partition.
The "ubi" mtd partition should be mtd7, check this using
$ cat /proc/mtd
Create a UBI partition by executing
$ ubiformat /dev/mtd7 -y
7. Increase the loadable kernel-size of U-Boot by executing
$ fw_setenv SysAKernSize 800000
8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using
scp. Install the image by using sysupgrade:
$ sysupgrade -n <path-to-sysupgrade>
Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might
have to change the ethernet-port.
9. OpenWrt should now boot from the internal NAND. Enjoy.
Signed-off-by: David Bauer <mail@david-bauer.net>
They are enabled by selecting devices. Fixes build errors when enabling extra
devices without creating a new config from scratch.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems more hardware needs early load of firmware when initialised
to work properly (at least Intel hardware). One of previous case is CPU
microcode, which this series[1] tried to change. The second one is Intel
graphics IC, which needs firmware for controlling DMC circuit (switch
conncted display to DC6 power state). As it stands, the i915 module is
built-in and it seems the hardware can't cope with firmware loaded
later from rootfs, it needs to be supplied when the module is loaded.
Unfortunately we need bootloader to handle the load of firmware in this
case, but as previously mentioned series[1], there was an error when
initrd was hardcoded, instead of testing existence for it and then
loading. To remedy this in later the 55b808e0c4 ('x86: image: add test
module to bootloader') was commited. Which was later accidentally
dropped when grub2 image creation was moved to packages. Therefore bring
back test module, so we can test for cases of existing firmware in
grub.cfg.
1. https://patchwork.ozlabs.org/project/openwrt/cover/20181120162044.16371-1-tomek_n@o2.pl
Fixes: 5a5df62d95 ("x86/grub2: move grub2 image creation to package")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell
Armada 370
Hardware:
SoC: Marvell Armada 88F6707
CPU: Cortex-A9 800 MHz, 1 core
Flash 1: SPI-NOR 1 MiB (U-Boot)
Flash 2: NAND 512 MiB (OS)
RAM: DDR3 256 MiB
Ethernet: 1x 1GbE
USB: 1x 2.0
SATA: 2x 3Gb/s
LEDs/Input: 5x / 2x (1x button, 1x slide-switch)
Fan: 1x casing
Flash instructions, from hard drive:
1. Get access to the "boot" partition at the hard drive where the stock
firmware is installed. It can be done with acp-commander or by
plugging the hard drive to a computer.
2. Backup the stock uImage:
mv /boot/uImage.buffalo /boot/uImage.buffalo.bak
3. Move and rename the Openwrt initramfs image to the boot partition:
mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo
4. Power on the Linkstation with the hardrive inside. Now Openwrt will
boot, but still not installed.
5. Connect via ssh to OpenWrt:
ssh root@192.168.1.1
6. Rename boot files inside boot partition
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak
mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak
7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"):
ubiformat /dev/mtd0 -y
ubidetach -p /dev/mtd1
ubiformat /dev/mtd1 -y
8. Flash the sysupgrade image:
sysupgrade -n openwrt-squashfs-sysupgrade.bin
9. Wait until it finish, the device will reboot with OpenWrt installed
on the NAND flash.
Restore the stock firmware:
1. Take the hard drive used for the installation and restore boot backup
files to their original names:
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo
mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo
2. Boot from the hard drive and perform a stock firmware update using
the Buffalo utility. The NAND will be restored to the original
state.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
FCC ID: A8J-EPG600
Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)
this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.
**Specification:**
- MT7620 SOC MIPS 24kec, 2.4 GHz WMAC, 2x2
- RT5592N WLAN PCI chip, 5 GHz, 2x2
- QCA8337N Gb SW RGMII GbE, SW P0 -- SOC P5, 5 LEDs
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 64 MB RAM NT5TU32M16
- UART console J2, populated
- USB 2.0 port direct to SOC
- 6 GPIO LEDs power, 2G, 5G, wps2g, wps5g, line
- 3 buttons reset, wps, "reg" (registeration)
- 4 antennas internal omni-directional plates
NOT YET SUPPORTED: VoIP
- Si3050-FT + Si3019-FT Voice DAA, SPI control, PCM data
- Phone Ports "TEL", "LINE" RJ11, 4P2C (2 pins)
**MAC addresses:**
MAC address labeled as MAC ADDRESS
MACs present in both wifi cal data and uboot environment
eth0.1/phy1 ---- *:82 rf 0x4
phy0 ---- *:83 factory 0x4
eth0.2 MAC *:b8 "wanaddr"
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.0.1
username and password 'admin'
Navigate to gear icon, "Device Management", "Tools"
select the factory.dlf image
Upload and verify checksum
Method 2: Serial to upload initramfs:
Follow directions for TFTP recovery
upload and boot initramfs and do a sysupgrade
**TFTP recovery:**
Requires UART serial console, reset button does nothing
rename initramfs-kernel.bin to 'uImageEPG600'
make available on TFTP server at 192.168.99.8
power board, interrupt boot with "4"
execute `tftpboot` and `bootm` (with the load address)
**Return to OEM:**
Images from OEM are provided, but not compatible
with openwrt sysupgrade. So it must be modified.
Alternatively, back up all mtd partitions before flashing
**Note on switch registers:**
The necessary registers needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by using the following lines in the switch driver ar8327.c
in the function 'ar8327_hw_config_of'
where 'qca,ar8327-initvals' is parsed from DTS
before the new register values are written:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Specifications:
- Device: ASUS RT-AX54 (AX1800S/HP,AX54HP)
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x POWER (blue, configurable)
1x LAN (blue, configurable)
1x WAN (blue, configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Karl Chan <exkc@exkc.moe>
Selecting the environment when booting from SD card has been broken by
a previous commit. Fix it.
Fixes: f46355b4d7 ("uboot-envtools: mediatek_filogic: fix BPi-R3 when no OS is installed")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Selecting the environment when booting from SD card has been broken by
a previous commit. Fix it.
Fixes: 84b5b0f88c ("uboot-envtools: mediatek/mt7622: don't rely on mapped rootfs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
FCC ID: A8J-EWS660AP
Engenius EWS660AP is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- QCA9880 WLAN mini PCIe card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- AR8033 PHY SGMII GbE with PoE+ OUT
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)
**MAC addresses:**
Base MAC addressed labeled as "MAC"
Only one Vendor MAC address in flash
eth0 *:d4 MAC art 0x0
eth1 *:d5 --- art 0x0 +1
phy1 *:d6 --- art 0x0 +2
phy0 *:d7 --- art 0x0 +3
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
**Format of OEM firmware image:**
The OEM software of EWS660AP is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-ews660ap-uImage-lzma.bin
openwrt-ar71xx-generic-ews660ap-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Tested-by: Niklas Arnitz <openwrt@arnitz.email>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This change consolidates Netgear EX7300 series devices into two images
corresponding to devices that share the same manufacturer firmware
image. Similar to the manufacturer firmware, the actual device model is
detected at runtime. The logic is taken from the netgear GPL dumps in a
file called generate_board_conf.sh.
Hardware details for EX7300 v2 variants
---------------------------------------
SoC: QCN5502
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 1 gigabit port
Wireless 2.4GHz (currently unsupported due to lack of ath9k support):
- EX6250 / EX6400 v2 / EX6410 / EX6420: QCN5502 3x3
- EX7300 v2 / EX7320: QCN5502 4x4
Wireless 5GHz:
- EX6250: QCA9986 3x3 (detected by ath10k as QCA9984 3x3)
- EX6400 v2 / EX6410 / EX6420 / EX7300 v2 / EX7320: QCA9984 4x4
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1 GB 2x Nanya NT5CC256M16ER-EK
* Storage:
* 8MB serial flash Winbond W25Q64DW
* 4GB eMMC flash Kingston EMMC04G-M627
* Ethernet:
* 4x1G RJ45 ports (QCA8074A) with 1x status LED per port
* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* 1x10G RJ45 port (AQR113C) with 1x status LED
* Switch: Qualcomm Atheros QCA8075
* WLAN:
* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
* 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
* Bluetooth CSR8811 using HSUART, currently unsupported
* USB: 1x USB3.0 Type-A port
* LED-s currently not supported:
* White
* Dark Blu
* Amber
* Purple
* Purple and dark blue
* Red
* Buttons:
* 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
* Disconnect WAN
* Reset device to factory defaults by pushing reset button 15 sec,
LEDs should lit orange color.
* After 5-10 minutes, when the LEDs turn constant dark blue,
put your LAN cable and connect at address 192.168.123.1 by telnet on port 23
* Login with
NBG7815 login: root
password: nbg7815@2019
* cd /tmp/ApplicationData
* wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://...
* wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh
* run flash_to_openwrt.sh
If you can't use wget, you can transfer the files via nc.
See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details.
Bluetooth usage:
* you need at least package bluez-utils, recommended bluez-daemon
* run following commands to enable and start
hciattach /dev/ttyMSM1 bcsp
hciconfig hci0 up
Many thanks to itorK for his work on this device:
https://github.com/itorK/openwrt/tree/nbg7815
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: André Valentin <avalentin@marcant.net>
Move defines from header to defconfig
The package build and the Buildbot hang in 'make syncconfig' for
u-boot-ravpower_rp-wd009 because CONFIG_SYS_MIPS_TIMER_FREQ is not in
the .config, causing a console prompt. Also moved two other defines in
defconfig causing duplicate definition warnings.
Fixes: 3d5c5427e1 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
The configured u_env partition for the Linksys WHW03 V2 was not correct.
It should have been set to mtd6.
This fix allow to flash the OEM firmware from OpenWRT and to change the
boot partition using fw_setenv.
Fixes: 9e4ede8344 ("ipq40xx: add support for Linksys WHW03 V2")
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
In the version 2023.01, the U-boot image was renamed because of the
upstream change [1]
[1] 87ac4b4b4c
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 256MB Nand
• Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• 1x USB 3.0
• 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard (J1004)
the connector size is a 4-pin 2.0 mm JST PH.
RX/TX is working, u-boot bootwait is active, secure boot is enabled.
Notes:
- Serial is completely deactivated in the stock firmware image.
- This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
- Installation can be done by serial connection or
SSH access on OEM firmware
Installation Instructions:
Most part of the installation is performed from an initramfs image
running OpenWrt, and there are two options to boot it.
Boot initramfs option 1: Using serial connection (3.3V)
1. Stop auto boot to get to U-boot shell
2. Transfer initramfs image to device
(openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
Tested using TFTP and a FAT-formatted USB flash drive.
3. Boot the initramfs image
# bootm
Boot initramfs option 2: From SSH access on OEM firmware
1. Copy the initramfs image to a FAT-formatted flash drive
(tested on single-partition drive) and connect it to device USB port.
2. Change boot command so it loads the initramfs image on next boot
Fallback to OEM firmware is provided.
# fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
3. Reboot the device to boot the initramfs
# reboot
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Check MTD partition table.
rootfs and rootfs_1 should be mtd18 and mtd20
depending on current OEM slot.
# cat /proc/mtd
4. Do a ubiformat to both rootfs partitions:
# ubiformat /dev/mtd18 -y -f /path_to/factory_image
# ubiformat /dev/mtd20 -y -f /path_to/factory_image
5. Set U-boot env variable: mtdids
# fw_setenv mtdids 'nand0=nand0'
6. Get offset of mtd18 to determine current OEM slot
- If current OEM slot is 1, offset is 16777216 (0x1000000)
- If current OEM slot is 2, offset is 127926272 (0x7a00000)
# cat /sys/class/mtd/mtd18/offset
7. Set U-boot env variable: mtdparts
If current OEM slot is 1, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
If current OEM slot is 2, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
8. Set U-boot env variable: bootcmd
# fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
9. Reboot the device
# reboot
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be
powered by either PoE or AC adapter.
Device info:
- IPQ8071-A SoC
- 1GiB RAM
- 256MiB NAND flash
- 32MiB SPI NOR
- 2 Ethernet ports
- 1 Console port
- 2GHz/5GHz AX WLAN
- 2 USB 2.0 ports
Install instructions:
Prerequistes - TFTP server, preferrably within 192.168.1.0/24
Console cable plugged in (115200 8N1 no flow control)
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server:
`setenv serverip 192.168.1.250`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet:
* 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
* 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate
* 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate
* USB: 1x USB3.0 Type-A port
* LED-s:
* System (Blue and Yellow)
* Network (Blue and Yellow)
* RGB light bar on top in X shape
* Buttons:
* 1x Power switch
* 1x Soft reset
* 1x Mesh button
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd21 and mtd22 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Robert Marko <robimarko@gmail.com>
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
(contains art and u-boot-env)
• Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
• WLAN:
2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate
• LEDs:
7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, hold WPS button til the second beep
(yes the router has a buzzer)
SSH is available on port 22200, login with user admin and
password "mac address of the router".
Installation Instructions:
• obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
• stop auto boot
• setenv serverip 192.168.10.1
• setenv ipaddr 192.168.10.10
• tftpboot the initramfs image
(openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
• bootm
• make sure that current_entry is set to "0":
"fw_printenv -n current_entry" should be print "0". If not,
do "fw_setenv current_entry 0"
• copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
to the device to /tmp folder
• sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
• reboot
Note: this leaves the second kernel / rootfs parition untouched. So if you want
to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
"saveenv", "bootipq".
Stock firmware should start from the second partition.
Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
in the first partitions
Make 10G Aquantia phy's work:
The aquantia phy's need a firmware to work. This can either be loaded
in linux with a userspace tool or in u-boot.
I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
aq_load_fw available in u-boot. But first the right firmware needs to write
to the 0:ETHPHYFW mtd partition (it is empty on my device)
Grab the ethphy firmware image from:
https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
and scp that to openwrt.
Check the 0:ETHPHYFW partition number:
cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.
Backup the 0:ETHPHYFW partition:
dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.
Write the new firmware image to the 0:ETHPHYFW partition:
"mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".
Reboot to u-boot.
Check if aq_load_fw is working:
"aq_load_fw 0", that checks the firmware and if successfull,
loads iram and dram to one of the aquantia phy's.
If that worked, add the aq_load_fw to the bootcmd:
setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"
"saveenv"
"reset"
Board reboots and the firmware load to both phy's should start and
then openwrt boots.
Check if the 10G ports work.
Note: lan port labeled "10G-2" is configured as WAN port as per default.
All other port are in the br-lan. This can be changed in the network config.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.
Specifications:
• CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
• RAM: 512MB of DDR3
• Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
3 x GPIO-controlled System-LEDs
(form one virtual RGB System-LED)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An unpopulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, but it drops only
to a limited shell .
Installation Instructions:
black_small_square obtain serial access
black_small_square stop auto boot
black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
black_small_square bootm
black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
to the device
black_small_square write the image to the NAND:
black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs-
nand-factory.ubi
black_small_square reboot
Note: Device is not using dual partitioning (NAND contains other partitions
with different manufacture data etc.)
Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Redmi AX6 is a budget 802.11ax dual-band router/AP
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 128MB NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LEDs:
* System (Blue/Yellow)
* Network (Blue/Yellow)
*Buttons: 1x soft reset
*Power: 12V DC jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Zhijun You <hujy652@gmail.com>
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* System (Blue and Yellow)
* IoT (Blue)
* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.
Specifications
--------------
SOC : Mediatek MT7621AT
ETH : Two 1 gigabit ports, built into the SOC
WIFI : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED : Power (green+red)
LED : WiFi (green+blue)
LED : WPS (green+red)
LED : Followme (green+red)
Power : 12 VDC, 1A barrel plug
Winbond variant:
RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1
Macronix variant:
RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1
Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.
The pinout is: VCC (the square), RX, TX, GND.
Installation
------------
See the Wiki page [1] for more details, it comes down to:
1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
environment located at 0x30000
Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.
MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use | address | example |
+----------+------------------+-------------------+
| Device | label | 00:00:00:11:00:00 |
| Ethernet | + 3 | 00:00:00:11:00:03 |
| 2g | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g | + 1 | 00:00:00:11:00:01 |
+----------+------------------+-------------------+
The label address is stored in ASCII in the board_data partition
Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
both partitions for more storage space.
Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
macaddr_add
- Only the power LED is configured by default
References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
SOC: Qualcomm IPQ4019
WiFi 1: QCA4019 IEEE 802.11b/g/n
WiFi 2: QCA4019 IEEE 802.11a/n/ac
WiFi 3: QCA8888 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet: Qualcomm Atheros QCA8072 (2-port)
Flash 1: Mactronix MX30LF4G18AC-XKI
RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB)
LED Controller: NXP PCA9633 (I2C)
Buttons: Single reset button (GPIO).
- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.
Bluetooth:
========
- Fully working with the following caveats:
- RFKILL need to be enabled in the kernel.
- An older version of bluez is needed as bccmd is needed to configure the chip.
Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.
Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.
The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.
It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
| J2
|
+--- Don't connect
Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
pressing 't'
3. Load and run OpenWrt initramfs image:
tftpboot
bootm
4. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
the OEM firmware
MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
| | MAC example 1 | MAC example 2 | Algorithm |
+---------+-------------------+-------------------+-------------+
| label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).
Notes
-----
[1] WAN MAC address:
a. First octet of WAN MAC is differ than others and OUI is not related
to TP-Link company. This probably should be fixed.
b. Flipping bits in first octet and hex delta are different for the
different MAC examples:
+-----------------+----------------+----------------+
| | Example 1 | Example 2 |
+-----------------+----------------+----------------+
| LAN | 68 = 0110 1000 | 50 = 0101 0000 |
| MAC (1st octet) | ^ ^ ^ | |
+-----------------+----------------+----------------+
| WAN | 72 = 0111 0010 | 54 = 0101 0100 |
| MAC (1st octet) | ^ ^ ^ | ^ |
+-----------------+----------------+----------------+
| HEX delta | 0xa | 0x4 |
+-----------------+----------------+----------------+
| DEC delta | 4 | 4 |
+-----------------+----------------+----------------+
c. DEC delta is a constant (4). This looks like a mistake in OEM
firmware and probably should be fixed.
Based on the above, I decided to keep correct OUI and make WAN MAC =
label + 1.
[2] Bootloaders
The device contains 3 bootloaders:
- First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
located on NAND Flash to load next full-feature Uboot.
- Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
bootloader includes recovery webserver. Requires special uImages to
continue the boot process:
0x00 (os0, os1) - firmware uImage
0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
- Additionally, both slots of the original TP-Link firmware contains
Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
magics and CRCs. We don't use this U-Boot with OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Support for MT7981 and MT7986 has been merged, remove patches.
Tested on a couple of MT7986, MT7622 and MT7623 boards.
MIPS builds are untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This converts the trusted firmware arm build Makefile to make use of
the common trusted-firmware-a.mk file. This also fixes the build with
binutils 2.39.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without these changes it used the system LDFLAGS for the compilation of
the cryptopp library. This does not always work when we add
"-no-warn-rwx-segments" which is done to support binutils 2.39 inside of
OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make use of the definitions from trusted-firmware-a.mk to build the
Trusted firmware arm. This fixes the build with binutils 2.39.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update the board name defined in DTS to match online documentation and the
name encoded into factory firmware. This helps supports flashing firmware
factory images using 'sysupgrade'.
Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB
instead of the correct 74 MB, and defines factory images which include
extra adjustments/padding that do not match OEM factory images and may
cause problems flashing. Update image size and build recipe to fix these.
Suggested-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
U-Boot flash instructions:
0. OpenWrt U-Boot does not support stock layout, it comes with recovery
boot support, automatic tftp recovery and never blocks UART.
A new flash layout is introduced, we call it OpenWrt U-Boot layout,
stock flash layout and the old OpenWrt layout are not supported.
During the whole flash procedure, please do not reboot or power off
unless requested explicitly, or you will break your device.
1. Your device should already running OpenWrt.
If not, follow the instructions to flash OpenWrt:
https://github.com/openwrt/openwrt/pull/11115
2. Backup BL2 Nvram Bdata Factory and FIP in case you break something or
in case you want to go back to stock firmware one day.
cat /dev/mtdblock0 > /tmp/BL2.bin
cat /dev/mtdblock1 > /tmp/Nvram.bin
cat /dev/mtdblock2 > /tmp/Bdata.bin
cat /dev/mtdblock3 > /tmp/Factory.bin
cat /dev/mtdblock4 > /tmp/FIP.bin
And save all whose bin files to somewhere safe.
Then backup your configurations, since ubiformat for entire mtd device is
required to create new ubootenv volume for OpenWrt U-Boot.
3. Run the following cmd to boot into an initramfs with the new OpenWrt
U-Boot layout that expand ubi partion to the end of flash:
ubiformat /dev/mtd7 -y -f /tmp/ax6000-ubootmod-initramfs-factory.ubi
4. After boot into initramfs, check mtd partion info.
The ubi partion should be mtd5
root@OpenWrt:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 BL2
mtd1: 00040000 00020000 Nvram
mtd2: 00040000 00020000 Bdata
mtd3: 00200000 00020000 Factory
mtd4: 00200000 00020000 FIP
mtd5: 07a80000 00020000 ubi
5. Load kmod-mtd-rw to temporarily make the bootloader partions writable.
The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory
by default.
To install kmod-mtd-rw via opkg:
opkg update && opkg install kmod-mtd-rw
Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually
e.g:
https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/
Select your OpenWrt release version and kernel version accordingly.
Load kmod-mtd-rw:
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1
6. Run the following cmd to clean all pending crash dumps in pstore,
or OpenWrt U-Boot may boot into NAND recovery or tftp recovery.
rm -f /sys/fs/pstore/*
7. Format ubi and create new ubootenv volume:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
8. This is optional. Skip this if you do not want to have NAND recovery
boot feature offered by OpenWrt U-Boot. Don't worry, you always have
automatic tftp recovery feature enabled.
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/ax6000-ubootmod-initramfs-recovery.itb
9. Now, flash new U-Boot. Bye-bye ugly stock U-Boot.
mtd write /tmp/ax6000-ubootmod-preloader.bin BL2
mtd write /tmp/ax6000-ubootmod-bl31-uboot.fip FIP
10. Flash the squashfs-sysupgrade.bin as usual:
sysupgrade -n /tmp/ax6000-ubootmod-squashfs-sysupgrade.itb
Enjoy!
Signed-off-by: Furong Xu <xfr@outlook.com>
Adds uboot-envtools support for ramips Asus RX-AX53U now that partition
can be correctly read.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Several sunxi devices come with multiple mmc devices. On such devices,
the mmc device order is unpredictable, so using /dev/mmcblk0p2 as root
device doesn't always work, which results in unbootable devices.
For the Banana Pi BPI-R3 in the mediatek target, this has been solved by
defining aliases for the mmc devices in the DTS. Ideally we would do the
same here, but for sunxi-a64 we already use UUID probing, so let's start
with that (5f2ff607e2 ("uboot-sunxi: a64: allow booting directly from
eMMC")).
Since we're building and including u-boot in each supported device
image, and this method has been proven to work fine for a64, let's just
change the default u-boot env file to do the same.
Fixes: #10080
Fixes: e6d9f6fdff ("sunxi: add support for FriendlyARM NanoPi R1")
Co-authored-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
[use UUID in default u-boot env, rewrite commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A
Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
"Administration/Management/Firmware update/Choose File" in vendor's
web interface (ip: 192.168.1.10, login: Admin, password: Admin).
Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
file by "System/Backup/Flash Firmware/Flash image..." in
LuCI web interface (ip: 192.168.1.1, login: root, no password).
Wait ~240 seconds.
Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing
Signed-off-by: Alexey Bartenev <41exey@proton.me>
The compatible in the device tree is "haoyu,a10-marsboard",
modify the board_name to keep it consistent.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.
1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
be helpful for users who may forget to do this before sysupgrade in
the initramfs.
New flash instructions:
1. Gain ssh access. Please refer to:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)
2. Check which system current u-boot is loading from:
COMMAND: `cat /proc/cmdline`
sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
if firmware=1, current system is ubi1
if firmware=0, current system is ubi0
3. Setup nvram and write the firmware:
If the current system is ubi1, please set it up so that the next time
it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
If the current system is ubi, please set it up so that the next time
it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```
4. After rebooting, the system should now boot into the openwrt initramfs.
Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.
For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:
1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```
2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface under admin account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following line:
<PARAMETER name="Password" type="string" value="<your router serial \
is here>" writable="1" encryption="1" password="1"/>
5. Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
ETxxxxxxxxxx is the serial number from the backplate label)
9. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:50 |
| WAN | label + 11 | *:5b |
| 2g | label + 2 | *:52 |
| 5g | label + 3 | *:53 |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Raise CONFIG_LMB_MAX_REGIONS to 64 as there are going to be more than
8 (the default value) reserved regions to allow supporting offloading
Wireless-to-Ethernet traffic on MT7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
At this moment LS1012A-FRDM have uncompressed initramfs image.
Error was caused, because gzip extract area overlap image.
Let's change loadaddr and enable gzip initramfs images again.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
FCC ID: A8J-EAP1750H
Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9558 SOC
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16FG
- UART at J10 populated
- 4 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)
**MAC addresses:**
MAC addresses are labeled as ETH, 2.4G, and 5GHz
Only one Vendor MAC address in flash
eth0 ETH *:fb art 0x0
phy1 2.4G *:fc ---
phy0 5GHz *:fd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
NOTE: TFTP is not reliable due to bugged bootloader
set MTU to 600 and try many times
if your TFTP server supports setting block size
higher block size is better.
**Format of OEM firmware image:**
The OEM software of EAP1750H is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
openwrt-ar71xx-generic-eap1750h-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Fix mmc_write_vol hush script used by many boards to avoid timeouts on
slow SD cards:
Instead of erasing a complete partition, only erase blocks for the
to-be-written image when writing to MMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ruckus ZoneFlex 7025 is a single 2.4GHz radio 802.11n 1x1 enterprise
access point with built-in Ethernet switch, in an electrical outlet form factor.
Hardware highligts:
- CPU: Atheros AR7240 SoC at 400 MHz
- RAM: 64MB DDR2
- Flash: 16MB SPI-NOR
- Wi-Fi: AR9285 built-in 2.4GHz 1x1 radio
- Ethernet: single Fast Ethernet port inside the electrical enclosure,
coupled with internal LSA connector for direct wiring,
four external Fast Ethernet ports on the lower side of the device.
- PoE: 802.3af PD input inside the electrical box.
802.3af PSE output on the LAN4 port, capable of sourcing
class 0 or class 2 devices, depending on power supply capacity.
- External 8P8C pass-through connectors on the back and right side of the device
- Standalone 48V power input on the side, through 2/1mm micro DC barrel jack
Serial console: 115200-8-N-1 on internal JP1 header.
Pinout:
---------- JP1
|5|4|3|2|1|
----------
Pin 1 is near the "H1" marking.
1 - RX
2 - n/c
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw,
but with much less manual steps, and is generally recommended, being
safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
work on some rare versions of stock firmware. A more involved, and
requires installing `mkenvimage` from u-boot-tools package if you
choose to rebuild your own environment, but can be used without
disassembly or removal from installation point, if you have the
credentials.
If for some reason, size of your sysupgrade image exceeds 13312kB,
proceed with method [1]. For official images this is not likely to
happen ever.
[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0x9f040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7025-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7025_fw1_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin
[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
it boots, hold the reset button near Ethernet connectors for 5
seconds.
1. Connect the device to the network. It will acquire address over DHCP,
so either find its address using list of DHCP leases by looking for
label MAC address, or try finding it by scanning for SSH port:
$ nmap 10.42.0.0/24 -p22
From now on, we assume your computer has address 10.42.0.1 and the device
has address 10.42.0.254.
2. Set up a TFTP server on your computer. We assume that TFTP server
root is at /srv/tftp.
3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
frmware is pretty ancient and requires enabling HMAC-MD5.
$ ssh 10.42.0.254 \
-o UserKnownHostsFile=/dev/null \
-o StrictHostKeyCheking=no \
-o MACs=hmac-md5
Login. User is "super", password is "sp-admin".
Now execute a hidden command:
Ruckus
It is case-sensitive. Copy and paste the following string,
including quotes. There will be no output on the console for that.
";/bin/sh;"
Hit "enter". The AP will respond with:
grrrr
OK
Now execute another hidden command:
!v54!
At "What's your chow?" prompt just hit "enter".
Congratulations, you should now be dropped to Busybox shell with root
permissions.
4. Optional, but highly recommended: backup the flash contents before
installation. At your PC ensure the device can write the firmware
over TFTP:
$ sudo touch /srv/tftp/ruckus_zf7025_firmware{1,2}.bin
$ sudo chmod 666 /srv/tftp/ruckus_zf7025_firmware{1,2}.bin
Locate partitions for primary and secondary firmware image.
NEVER blindly copy over MTD nodes, because MTD indices change
depending on the currently active firmware, and all partitions are
writable!
# grep rcks_wlan /proc/mtd
Copy over both images using TFTP, this will be useful in case you'd
like to return to stock FW in future. Make sure to backup both, as
OpenWrt uses bot firmwre partitions for storage!
# tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7025_firmware1.bin -p 10.42.0.1
# tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7025_firmware2.bin -p 10.42.0.1
When the command finishes, copy over the dump to a safe place for
storage.
$ cp /srv/tftp/ruckus_zf7025_firmware{1,2}.bin ~/
5. Ensure the system is running from the BACKUP image, i.e. from
rcks_wlan.bkup partition or "image 2". Otherwise the installation
WILL fail, and you will need to access mtd0 device to write image
which risks overwriting the bootloader, and so is not covered here
and not supported.
Switching to backup firmware can be achieved by executing a few
consecutive reboots of the device, or by updating the stock firmware. The
system will boot from the image it was not running from previously.
Stock firmware available to update was conveniently dumped in point 4 :-)
6. Prepare U-boot environment image.
Install u-boot-tools package. Alternatively, if you build your own
images, OpenWrt provides mkenvimage in host staging directory as well.
It is recommended to extract environment from the device, and modify
it, rather then relying on defaults:
$ sudo touch /srv/tftp/u-boot-env.bin
$ sudo chmod 666 /srv/tftp/u-boot-env.bin
On the device, find the MTD partition on which environment resides.
Beware, it may change depending on currently active firmware image!
# grep u-boot-env /proc/mtd
Now, copy over the partition
# tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1
Store the stock environment in a safe place:
$ cp /srv/tftp/u-boot-env.bin ~/
Extract the values from the dump:
$ strings u-boot-env.bin | tee u-boot-env.txt
Now clean up the debris at the end of output, you should end up with
each variable defined once. After that, set the bootcmd variable like
this:
bootcmd=bootm 0x9f040000
You should end up with something like this:
bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),7168k(rcks_wlan.main),7168k(rcks_wlan.bkup),1280k(datafs),256k(u-boot-env)
mtdids=nor0=ar7100-nor0
bootdelay=2
filesize=52e000
fileaddr=81000000
ethact=eth0
stdin=serial
stdout=serial
stderr=serial
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=192.168.0.1
serverip=192.168.0.2
stderr=serial
ethact=eth0
These are the defaults, you can use most likely just this as input to
mkenvimage.
Now, create environment image and copy it over to TFTP root:
$ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
$ sudo cp u-boot-env.bin /srv/tftp
This is the same image, gzipped and base64-encoded: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7. Perform actual installation. Copy over OpenWrt sysupgrade image to
TFTP root:
$ sudo cp openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin /srv/tftp
Now load both to the device over TFTP:
# tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
# tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin -g 10.42.0.1
Verify checksums of both images to ensure the transfer over TFTP
was completed:
# sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin
And compare it against source images:
$ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin
Locate MTD partition of the primary image:
# grep rcks_wlan.main /proc/mtd
Now, write the images in place. Write U-boot environment last, so
unit still can boot from backup image, should power failure occur during
this. Replace MTD placeholders with real MTD nodes:
# flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
# flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>
Finally, reboot the device. The device should directly boot into
OpenWrt. Look for the characteristic power LED blinking pattern.
# reboot -f
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Boot into OpenWrt initramfs as for initial installation. To do that
without disassembly, you can write an initramfs image to the device
using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Concatenate the firmware backups, if you took them during installation using method 2:
$ cat ruckus_zf7025_fw1_backup.bin ruckus_zf7025_fw2_backup.bin > ruckus_zf7025_backup.bin
3. Write factory images downloaded from manufacturer website into
fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
before installation:
# mtd write ruckus_zf7025_backup.bin /dev/mtd1
4. Reboot the system, it should load into factory firmware again.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- The 2.4 GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Inspired by commit 9565c5726a, and by
facts that all Ubiquiti XM devices share flash layout, and images are
mostly compatible between all of them - enable uboot-envtools support for
whole XM line.
Build tested on: Ubiquiti Airrouter, Bullet-M (7240,7241), Nanobridge-M,
Nanostation-M (+ Loco), Picostation-M, Powerbridge-M, Rocket-M.
Runtime tested on: Ubiquiti Nanobridge M5 (XM).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
firmware
6. Update firmware using web interface with the OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+------------+
| use | address | example |
+-----+------------+------------+
| LAN | label | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g | label + 2 | *:74, *:d4 |
| 5g | label + 3 | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB: 1 x USB 3.0 port
Button: 1 x Reset button
Switch: 1 x Mode switch
LED: 1 x Blue LED + 1 x White LED
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based
on Tenbay WR1800K. They have the same hardware circuits and u-boot.
SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile),
SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these
models run the same firmware.
Specifications:
SOC: MT7621 + MT7905 + MT7975
ROM: 128 MiB
RAM: 256 MiB
LED: status *3 R/G/B
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP Server: 192.168.1.254
TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken)
MAC Address:
use address source
label 30:xx:xx:xx:xx:62 wan
lan 30:xx:xx:xx:xx:65 factory.0x8004
wan 30:xx:xx:xx:xx:62 factory.0x8004 -3
wlan2g 30:xx:xx:xx:xx:64 factory.0x0004
wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit
TFTP Installation (initramfs image only & recommend):
1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
directory of the tftp server. (tftpd64 is a good choice for Windows)
3. Start the TFTP server, plug in the power supply, and wait for the
system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin", we need
it to back to stock firmware.
5. Use "fw_printenv" command to list envs.
If "firmware_select=2" is observed then set u-boot enviroment:
/# fw_setenv firmware_select 1
6. Apply sysupgrade.bin in OpenWrt LuCI.
Web UI Installation:
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs.
If "firmware_select=2" is observed then set u-boot enviroment:
/# fw_setenv firmware_select 1
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.
Recovery to stock firmware:
a. Upload "firmware.bin" to OpenWrt /tmp, then execute:
/# mtd -r write /tmp/firmware.bin firmware
b. We can also write factory image "UploadBrush-bin.img" to firmware
partition to recovery. Upload image file to /tmp, then execute:
/# mtd erase firmware
/# mtd -r write /tmp/UploadBrush-bin.img firmware
How to extract stock firmware image:
Download stock firmware, then use openssl:
openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \
-out "firmware.tar.tgz" -k QiLunSmartWL
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In a254279a6c LS1012A-IOT kernel image was switched to FIT.
But u-boot config is lack of FIT and ext4 support.
This patch enables it.
It also fix envs, because for some reason this board need to use "loadaddr"
variable in brackets.
Fixes: #9894
Fixes: a254279a6c ("layerscape: Change to combined rootfs on sd images")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The sector number must be stored in hex. Otherwise, the number (like 16)
will be parsed as hex and any write to the partition will end up with an
error like:
MTD erase error on /dev/mtd5: Invalid argument
Fixes: 9adfeccd84 ("uboot-envtools: Add support for IPQ806x AP148 and DB149")
Fixes: 54b275c8ed ("ipq40xx: add target")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@fungible.com>
Add support for the Linksys EA4500 v3 wireless router
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Winbond W971GG6KB-25)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
QCA9580 3T3R 802.11 an
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1, same as ea4500 v2
USB: 1 single USB 2.0 host port
BUTTON: Reset - WPS
LED: 1x system-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label 94:10:3e:xx:xx:6f caldata@cal_macaddr
lan 94:10:3e:xx:xx:6f $label
wan 94:10:3e:xx:xx:6f $label
WiFi4_2G 94:10:3e:xx:xx:70 caldata@cal_ath9k_soc
WiFi4_5G 94:10:3e:xx:xx:71 caldata@cal_ath9k_pci
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.1.0/24
(e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
initramfs image as "openwrt.bin"
3. To test OpenWrt only, go to step 4 and never execute step 5;
To install, auto_recovery should be disabled first, and boot_part
should be set to 1 if its current value is not.
ath> setenv auto_recovery no
ath> setenv boot_part 1
ath> saveenv
4. Boot the initramfs image using U-Boot
ath> setenv serverip 192.168.1.66
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm
5. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Note: Like many other routers produced by Linksys, it has a dual
firmware flash layout, but because I do not know how to handle
it, I decide to disable it for more usable space. (That is why
the "auto_recovery" above should be disabled before installing
OpenWRT.) If someone is interested in generating factory
firmware image capable to flash from stock firmware, as well as
restoring the dual firmware layout, commented-out layout for the
original secondary partitions left in the device tree may be a
useful hint.
Installation from Web Interface
------------
1. Login to the router via its web interface (default password: admin)
2. Find the firmware update interface under "Connectivity/Basic"
3. Choose the OpenWrt factory image and click "Start"
4. If the router still boots into the stock firmware, it means that
the OpenWrt factory image has been installed to the secondary
partitions and failed to boot (since OpenWrt on EA4500 v3 does not
support dual boot yet), and the router switched back to the stock
firmware on the primary partitions. You have to install a stock
firmware (e.g. 3.1.6.172023, downloadable from
https://www.linksys.com/support-article?articleNum=148385 ) first
(to the secondary partitions) , and after that, install OpenWrt
factory image (to the primary partitions). After successful
installation of OpenWrt, auto_recovery will be automatically
disabled and router will only boot from the primary partitions.
Signed-off-by: Edward Chow <equu@openmail.cc>
