mirror of
https://github.com/openwrt/openwrt.git
synced 2025-03-25 13:28:08 +00:00
mediatek: add support for Cetron CT3003
**Hardware specification:** - SoC: MediaTek MT7981B 2x A53 - Flash: ESMT F50L1G41LB 128MB - RAM: Nanya NT5CC128M16JR-EK 256MB - Ethernet: 4 x 10/100/1000 Mbps - Switch: MediaTek MT7531AE - WiFi: MediaTek MT7976C - Button: Reset, Mesh - Power: DC 12V 1A - UART: 3.3v, 115200n8 | Layout: | | :-------- | | <Antenna> | | VCC | | GND | | Tx | | Rx | **Flash instructions:** 1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`. 2. Upload the `factory.bin` using the device's Web interface. 3. Click the upgrade button and wait for the process to finish. 4. Access the OpenWrt interface using the same password. 5. Use the 'Restore' function to reset the firmware to its initial state. **Notes:** If you plan to recovery the stock firmware in the future, it's advisable to connect the device via the serial port and enter failsafe mode to back up all the MTD partitions before proceeding the steps above. Signed-off-by: Patricia Lee <patricialee320@gmail.com>
This commit is contained in:
Patricia Lee
Hauke Mehrtens
parent
58bb5e147a
commit
907e9e0bd3
@ -44,6 +44,7 @@ mercusys,mr90x-v1)
|
||||
local envdev=/dev/mtd$(find_mtd_index "u-boot-env")
|
||||
ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1"
|
||||
;;
|
||||
cetron,ct3003|\
|
||||
netgear,wax220)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
||||
;;
|
||||
|
||||
242
target/linux/mediatek/dts/mt7981b-cetron-ct3003.dts
Normal file
242
target/linux/mediatek/dts/mt7981b-cetron-ct3003.dts
Normal file
@ -0,0 +1,242 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Cetron CT3003";
|
||||
compatible = "cetron,ct3003", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
led-boot = &led_status_red;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_green;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x10000000>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_red: led_status_red {
|
||||
label = "red:status";
|
||||
gpios = <&pio 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_status_green: led_status_green {
|
||||
label = "green:status";
|
||||
gpios = <&pio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
nvmem-cells = <&macaddr_art_0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
switch: switch@0 {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <31>;
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand@0 {
|
||||
compatible = "spi-nand";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-buswidth = <4>;
|
||||
spi-rx-buswidth = <4>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x0000000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x0100000 0x0080000>;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "art";
|
||||
reg = <0x0180000 0x0100000>;
|
||||
read-only;
|
||||
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_art_0: macaddr@0 {
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
};
|
||||
|
||||
factory: partition@280000 {
|
||||
label = "Factory";
|
||||
reg = <0x0280000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x0380000 0x0200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x0580000 0x2000000>;
|
||||
};
|
||||
|
||||
partition@2580000 {
|
||||
label = "ubi_backup";
|
||||
reg = <0x2580000 0x2000000>;
|
||||
};
|
||||
|
||||
partition@4580000 {
|
||||
label = "Config_backup";
|
||||
reg = <0x4580000 0x0400000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
@ -42,6 +42,7 @@ mediatek_setup_interfaces()
|
||||
mercusys,mr90x-v1)
|
||||
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2" eth1
|
||||
;;
|
||||
cetron,ct3003|\
|
||||
qihoo,360t7)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
|
||||
;;
|
||||
@ -82,6 +83,11 @@ mediatek_setup_macs()
|
||||
bananapi,bpi-r3)
|
||||
wan_mac=$(macaddr_add $(cat /sys/class/net/eth0/address) 1)
|
||||
;;
|
||||
cetron,ct3003)
|
||||
lan_mac=$(mtd_get_mac_binary "art" 0)
|
||||
wan_mac=$(macaddr_add "$lan_mac" 3)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
h3c,magic-nx30-pro)
|
||||
wan_mac=$(mtd_get_mac_ascii pdt_data_1 ethaddr)
|
||||
lan_mac=$(macaddr_add "$wan_mac" 1)
|
||||
|
||||
@ -30,6 +30,11 @@ case "$board" in
|
||||
[ "$PHYNBR" = "0" ] && macaddr_unsetbit $addr 6 > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" = "1" ] && macaddr_setbit $addr 6 > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
cetron,ct3003)
|
||||
addr=$(mtd_get_mac_binary "art" 0)
|
||||
[ "$PHYNBR" = "0" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 2) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
cudy,wr3000-v1)
|
||||
addr=$(mtd_get_mac_binary bdinfo 0xde00)
|
||||
# Originally, phy0 is phy1 mac with LA bit set. However, this would conflict
|
||||
|
||||
@ -90,6 +90,21 @@ define Build/zyxel-nwa-fit-filogic
|
||||
@mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/cetron-header
|
||||
$(eval magic=$(word 1,$(1)))
|
||||
$(eval model=$(word 2,$(1)))
|
||||
( \
|
||||
dd if=/dev/zero bs=856 count=1 2>/dev/null; \
|
||||
printf "$(model)," | dd bs=128 count=1 conv=sync 2>/dev/null; \
|
||||
md5sum $@ | cut -f1 -d" " | dd bs=32 count=1 2>/dev/null; \
|
||||
printf "$(magic)" | dd bs=4 count=1 conv=sync 2>/dev/null; \
|
||||
cat $@; \
|
||||
) > $@.tmp
|
||||
fw_crc=$$(gzip -c $@.tmp | tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n'); \
|
||||
printf "$$(echo $$fw_crc | sed 's/../\\x&/g')" | cat - $@.tmp > $@
|
||||
rm $@.tmp
|
||||
endef
|
||||
|
||||
define Device/asus_tuf-ax4200
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_MODEL := TUF-AX4200
|
||||
@ -172,6 +187,23 @@ define Device/bananapi_bpi-r3
|
||||
endef
|
||||
TARGET_DEVICES += bananapi_bpi-r3
|
||||
|
||||
define Device/cetron_ct3003
|
||||
DEVICE_VENDOR := Cetron
|
||||
DEVICE_MODEL := CT3003
|
||||
DEVICE_DTS := mt7981b-cetron-ct3003
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb
|
||||
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | cetron-header rd30 CT3003
|
||||
endef
|
||||
TARGET_DEVICES += cetron_ct3003
|
||||
|
||||
define Device/cudy_wr3000-v1
|
||||
DEVICE_VENDOR := Cudy
|
||||
DEVICE_MODEL := WR3000
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user