mirror of
https://github.com/openwrt/openwrt.git
synced 2025-04-13 22:23:38 +00:00
ramips: add support for ZyXEL LTE5398-M904
ZyXEL LTE5398-M904 is a dual band 802.11ac indoor LTE/3G CPE with an FXS port. Specifications: * SoC: Mediatek MT7621AT * RAM: 256 MB * Flash: 128MB NAND (MX30LF1G18AC) * WiFi: MediaTek MT7603 2.4G + MediaTek MT7615 5G * Switch: 2 GbE ports MT7530 * LTE/3G: Quectel EG18-EA LTE-A Cat. 18 * SIM: 1 micro-SIM card slot * Buttons: Reset, WPS * LEDs: power (G/B), internet (G), LTE (R/G/Orange), WiFi (G), voice (G) * VoIP: 1 FXS RJ11 port * Power: 12V, 2A UART serial console: 57600,8N1 Unpopulated header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Installation: * Log in as root using ssh to 192.168.1.1 * scp OpenWrt initramfs-recovery.bin image to root@192.168.1.1:/tmp/ * Prepare bootloader config by running: nvram setro uboot DebugFlag 0x1 nvram setro uboot CheckBypass 0 nvram commit * Run "mtd_write -w write /tmp/initramfs-recovery.bin Kernel" and reboot * Wait for OpenWrt to boot and ssh to root@192.168.1.1 * Run sysupgrade with OpenWrt squashfs-sysupgrade.bin image For mode details about flashing see: 2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19) Unsupported: * FXS/Voice Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
This commit is contained in:
Milan Krstic
Hauke Mehrtens
parent
da52c6f50e
commit
17465fc77e
@ -127,6 +127,7 @@ xiaomi,redmi-router-ac2100)
|
||||
zyxel,lte3301-plus)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x80000"
|
||||
;;
|
||||
zyxel,lte5398-m904|\
|
||||
zyxel,nr7101)
|
||||
idx="$(find_mtd_index Config)"
|
||||
[ -n "$idx" ] && \
|
||||
|
||||
228
target/linux/ramips/dts/mt7621_zyxel_lte5398-m904.dts
Normal file
228
target/linux/ramips/dts/mt7621_zyxel_lte5398-m904.dts
Normal file
@ -0,0 +1,228 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "zyxel,lte5398-m904", "mediatek,mt7621-soc";
|
||||
model = "ZyXEL LTE5398-M904";
|
||||
|
||||
aliases {
|
||||
label-mac-device = &gmac0;
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_green;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_green: power_green {
|
||||
label = "green:power";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
power_blue {
|
||||
label = "blue:power";
|
||||
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&ehci_port2>;
|
||||
};
|
||||
|
||||
internet {
|
||||
label = "green:internet";
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wifi {
|
||||
label = "green:wifi";
|
||||
gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
voice {
|
||||
label = "green:voice";
|
||||
gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lte_green {
|
||||
label = "green:lte";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lte_orange {
|
||||
label = "orange:lte";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lte_red {
|
||||
label = "red:lte";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
lte_power {
|
||||
gpio-export,name = "lte_power";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb_power {
|
||||
gpio-export,name = "usb_power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Bootloader";
|
||||
reg = <0x0 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "Config";
|
||||
reg = <0x80000 0x80000>;
|
||||
};
|
||||
|
||||
factory: partition@100000 {
|
||||
compatible = "nvmem-cells";
|
||||
label = "Factory";
|
||||
reg = <0x100000 0x40000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
read-only;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x400>;
|
||||
};
|
||||
|
||||
eeprom_factory_8000: eeprom@8000 {
|
||||
reg = <0x8000 0x4da8>;
|
||||
};
|
||||
|
||||
macaddr_factory_fe6e: macaddr@fe6e {
|
||||
reg = <0xfe6e 0x6>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "Kernel";
|
||||
reg = <0x140000 0x1ec0000>;
|
||||
};
|
||||
|
||||
partition@540000 {
|
||||
label = "ubi";
|
||||
reg = <0x540000 0x1ac0000>;
|
||||
};
|
||||
|
||||
partition@2140000 {
|
||||
label = "Kernel2";
|
||||
reg = <0x2140000 0x1ec0000>;
|
||||
};
|
||||
|
||||
partition@4000000 {
|
||||
label = "wwan";
|
||||
reg = <0x4000000 0x100000>;
|
||||
};
|
||||
|
||||
partition@4100000 {
|
||||
label = "data";
|
||||
reg = <0x4100000 0x1000000>;
|
||||
};
|
||||
|
||||
partition@5100000 {
|
||||
label = "rom-d";
|
||||
reg = <0x5100000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5200000 {
|
||||
label = "reserve";
|
||||
reg = <0x5200000 0x80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ðernet {
|
||||
pinctrl-0 = <&mdio_pins>, <&rgmii1_pins>;
|
||||
};
|
||||
|
||||
&state_default {
|
||||
gpio {
|
||||
groups = "i2c", "rgmii2", "uart3", "jtag", "wdt";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
nvmem-cells = <&macaddr_factory_fe6e>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@0 {
|
||||
status = "okay";
|
||||
label = "lan1";
|
||||
};
|
||||
port@2 {
|
||||
status = "okay";
|
||||
label = "lan2";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cells = <&eeprom_factory_0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cells = <&eeprom_factory_8000>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
};
|
||||
};
|
||||
@ -2974,6 +2974,21 @@ define Device/zyxel_lte3301-plus
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_lte3301-plus
|
||||
|
||||
define Device/zyxel_lte5398-m904
|
||||
$(Device/nand)
|
||||
DEVICE_VENDOR := ZyXEL
|
||||
DEVICE_MODEL := LTE5398-M904
|
||||
KERNEL_SIZE := 31488k
|
||||
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware kmod-usb3 uqmi \
|
||||
kmod-usb-net-qmi-wwan kmod-usb-serial-option kmod-usb-ledtrig-usbport
|
||||
KERNEL := $(KERNEL_DTB) | uImage lzma | \
|
||||
zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
|
||||
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | \
|
||||
zytrx-header $$(DEVICE_MODEL) 9.99(ABQU.1)$$(VERSION_DIST)-recovery
|
||||
KERNEL_INITRAMFS_SUFFIX := -recovery.bin
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_lte5398-m904
|
||||
|
||||
define Device/zyxel_nr7101
|
||||
$(Device/nand)
|
||||
DEVICE_VENDOR := ZyXEL
|
||||
|
||||
@ -248,6 +248,9 @@ yuncore,ax820)
|
||||
zyxel,lte3301-plus)
|
||||
ucidef_set_led_netdev "internet" "internet" "white:internet" "wwan0"
|
||||
;;
|
||||
zyxel,lte5398-m904)
|
||||
ucidef_set_led_netdev "internet" "LTE/3G Internet Activity" "green:internet" "wwan0" "rx tx"
|
||||
;;
|
||||
esac
|
||||
|
||||
board_config_flush
|
||||
|
||||
@ -148,6 +148,10 @@ ramips_setup_interfaces()
|
||||
ubnt,usw-flex)
|
||||
ucidef_set_interface_lan "lan1 lan2 lan3 lan4 lan5"
|
||||
;;
|
||||
zyxel,lte5398-m904)
|
||||
ucidef_set_interface_lan "lan1 lan2"
|
||||
ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
|
||||
;;
|
||||
zyxel,wap6805)
|
||||
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
|
||||
ucidef_set_interface "qtn" ifname "eth1" protocol "static" ipaddr "1.1.1.1" netmask "255.255.255.0"
|
||||
|
||||
@ -29,7 +29,8 @@ ubnt,edgerouter-x-sfp)
|
||||
ucidef_add_gpio_switch "poe_power_port3" "PoE Power Port3" "403"
|
||||
ucidef_add_gpio_switch "poe_power_port4" "PoE Power Port4" "404"
|
||||
;;
|
||||
zyxel,lte3301-plus)
|
||||
zyxel,lte3301-plus|\
|
||||
zyxel,lte5398-m904)
|
||||
ucidef_add_gpio_switch "usb_power" "Power USB Port" "usb_power" "1"
|
||||
ucidef_add_gpio_switch "lte_power" "Power LTE modem" "lte_power" "1"
|
||||
;;
|
||||
|
||||
@ -34,6 +34,7 @@ boot() {
|
||||
[ $(printf %d $(fw_printenv -n Image1Stable)) -gt 0 ] || fw_setenv Image1Stable 1
|
||||
[ $(printf %d $(fw_printenv -n Image1Try)) -gt 0 ] && fw_setenv Image1Try 0
|
||||
;;
|
||||
zyxel,lte5398-m904|\
|
||||
zyxel,nr7101)
|
||||
[ $(printf %d $(fw_printenv -n DebugFlag)) -gt 0 ] || fw_setenv DebugFlag 0x1
|
||||
[ $(printf %d $(fw_printenv -n Image1Stable)) -gt 0 ] || fw_setenv Image1Stable 1
|
||||
|
||||
@ -149,6 +149,7 @@ platform_do_upgrade() {
|
||||
platform_upgrade_ubnt_erx "$1"
|
||||
;;
|
||||
zyxel,lte3301-plus|\
|
||||
zyxel,lte5398-m904|\
|
||||
zyxel,nr7101)
|
||||
fw_setenv CheckBypass 0
|
||||
fw_setenv Image1Stable 0
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user