mirror of
https://github.com/openwrt/openwrt.git
synced 2025-02-02 17:20:59 +00:00
ipq807x: add support for Netgear WAX620
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
Use the header closest to LED 4 and 5.
They are marked with a white stroke.
TX RX GND, beginning from "4". 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)
Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)
Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```
```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
This commit is contained in:
Kristian Skramstad
Hauke Mehrtens
parent
f86415085b
commit
76e419288f
@ -10,7 +10,8 @@ board=$(board_name)
|
||||
case "$board" in
|
||||
dynalink,dl-wrx36|\
|
||||
netgear,rax120v2|\
|
||||
netgear,wax218)
|
||||
netgear,wax218|\
|
||||
netgear,wax620)
|
||||
idx="$(find_mtd_index 0:appsblenv)"
|
||||
[ -n "$idx" ] && \
|
||||
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
|
||||
|
||||
@ -35,6 +35,7 @@ ALLWIFIBOARDS:= \
|
||||
edimax_cax1800 \
|
||||
netgear_rax120v2 \
|
||||
netgear_wax218 \
|
||||
netgear_wax620 \
|
||||
prpl_haze \
|
||||
qnap_301w \
|
||||
redmi_ax6 \
|
||||
@ -126,6 +127,7 @@ $(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
|
||||
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
|
||||
$(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2))
|
||||
$(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218))
|
||||
$(eval $(call generate-ipq-wifi-package,netgear_wax620,Netgear WAX620))
|
||||
$(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w))
|
||||
$(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze))
|
||||
$(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
|
||||
|
||||
@ -0,0 +1,201 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq8074.dtsi"
|
||||
#include "ipq8074-hk-cpu.dtsi"
|
||||
#include "ipq8074-ess.dtsi"
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
/ {
|
||||
model = "Netgear WAX620";
|
||||
compatible = "netgear,wax620", "qcom,ipq8074";
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart5;
|
||||
ethernet0 = &dp6;
|
||||
led-boot = &led_system_blue;
|
||||
led-failsafe = &led_system_red;
|
||||
led-running = &led_system_green;
|
||||
led-upgrade = &led_system_blue;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
/*
|
||||
* Netgear's U-Boot adds "ubi.mtd=rootfs root=mtd:ubi_rootfs"
|
||||
* That fails to create a UBI block device, so add it here.
|
||||
*/
|
||||
bootargs-append = " root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 52 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
led_spi {
|
||||
compatible = "spi-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
sck-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
|
||||
mosi-gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
led_gpio: led_gpio@0 {
|
||||
compatible = "fairchild,74hc595";
|
||||
reg = <0>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
registers-number = <1>;
|
||||
enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
|
||||
spi-max-frequency = <1000000>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_system_red: system-red {
|
||||
label = "system:red";
|
||||
gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_system_green: system-green {
|
||||
label = "system:green";
|
||||
gpios = <&tlmm 55 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_system_blue: system-blue {
|
||||
label = "system:blue";
|
||||
gpios = <&tlmm 56 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_lan_g {
|
||||
label = "lan:green";
|
||||
gpios = <&led_gpio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_lan_o {
|
||||
label = "lan:orange";
|
||||
gpios = <&led_gpio 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_2g_b {
|
||||
label = "wlan2g:blue";
|
||||
gpios = <&led_gpio 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_2g_g {
|
||||
label = "wlan2g:green";
|
||||
gpios = <&led_gpio 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_5g_b {
|
||||
label = "wlan5g:blue";
|
||||
gpios = <&led_gpio 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_5g_g {
|
||||
label = "wlan5g:green";
|
||||
gpios = <&led_gpio 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
|
||||
&edma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_cpu_bmp = <0x01>;
|
||||
switch_lan_bmp = <0x3e>;
|
||||
switch_wan_bmp = <0x40>;
|
||||
switch_mac_mode = <0x00>;
|
||||
switch_mac_mode1 = <0xff>;
|
||||
switch_mac_mode2 = <0x0f>;
|
||||
bm_tick_mode = <0x00>;
|
||||
tm_tick_mode = <0x00>;
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@5 {
|
||||
port_id = <6>;
|
||||
phy_address = <28>;
|
||||
port_mac_sel = "QGMAC_PORT";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pins {
|
||||
mdc {
|
||||
pins = "gpio68";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio {
|
||||
pins = "gpio69";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
|
||||
|
||||
qca8081_28: ethernet-phy@28 {
|
||||
reg = <28>;
|
||||
};
|
||||
};
|
||||
|
||||
&dp6 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8081_28>;
|
||||
label = "lan";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-bus-width = <8>;
|
||||
|
||||
partitions {
|
||||
compatible = "qcom,smem-part";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath11k-calibration-variant = "Netgear-WAX620";
|
||||
};
|
||||
@ -115,6 +115,20 @@ define Device/netgear_rax120v2
|
||||
endef
|
||||
TARGET_DEVICES += netgear_rax120v2
|
||||
|
||||
define Device/netgear_wax620
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Netgear
|
||||
DEVICE_MODEL := WAX620
|
||||
DEVICE_DTS_CONFIG := config@hk07
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
SOC := ipq8072
|
||||
DEVICE_PACKAGES += kmod-spi-gpio kmod-gpio-nxp-74hc164 \
|
||||
ipq-wifi-netgear_wax620
|
||||
endef
|
||||
TARGET_DEVICES += netgear_wax620
|
||||
|
||||
define Device/netgear_wax218
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
|
||||
@ -12,6 +12,9 @@ edgecore,eap102)
|
||||
netgear,rax120v2)
|
||||
ucidef_set_led_netdev "aqr" "AQR" "white:aqr" "lan5"
|
||||
;;
|
||||
netgear,wax620)
|
||||
ucidef_set_led_netdev "lan" "LAN" "lan:green" "lan"
|
||||
;;
|
||||
netgear,wax218)
|
||||
ucidef_set_led_netdev "lan" "LAN" "blue:lan" "lan"
|
||||
ucidef_set_led_wlan "wlan5g" "WIFI 5GHz" "blue:wlan5g" "phy0radio"
|
||||
|
||||
@ -25,7 +25,8 @@ ipq807x_setup_interfaces()
|
||||
netgear,rax120v2)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "wan"
|
||||
;;
|
||||
netgear,wax218)
|
||||
netgear,wax218|\
|
||||
netgear,wax620)
|
||||
ucidef_set_interface_lan "lan" "dhcp"
|
||||
;;
|
||||
prpl,haze)
|
||||
|
||||
@ -16,6 +16,7 @@ case "$FIRMWARE" in
|
||||
dynalink,dl-wrx36|\
|
||||
netgear,rax120v2|\
|
||||
netgear,wax218|\
|
||||
netgear,wax620|\
|
||||
qnap,301w|\
|
||||
redmi,ax6|\
|
||||
xiaomi,ax3600|\
|
||||
|
||||
@ -69,7 +69,8 @@ platform_do_upgrade() {
|
||||
compex,wpq873|\
|
||||
edimax,cax1800|\
|
||||
netgear,rax120v2|\
|
||||
netgear,wax218)
|
||||
netgear,wax218|\
|
||||
netgear,wax620)
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
prpl,haze|\
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user