mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 05:38:00 +00:00
Revert "ipq807x: add initial support for prpl Foundation Haze board"
This reverts commit 48603a271e as this
was commited by accident, its still work in progress.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit is contained in:
Petr Štetiar
parent
b6a14ef7b9
commit
a3ee2bf9a1
@ -36,11 +36,6 @@ xiaomi,ax9000)
|
||||
[ -n "$idx2" ] && \
|
||||
ubootenv_add_uci_sys_config "/dev/mtd$idx2" "0x0" "0x10000" "0x20000"
|
||||
;;
|
||||
prpl,haze)
|
||||
mmcpart="$(find_mmc_part 0:APPSBLENV)"
|
||||
[ -n "$mmcpart" ] && \
|
||||
ubootenv_add_uci_config "$mmcpart" "0x0" "0x40000" "0x400" "0x100"
|
||||
;;
|
||||
qnap,301w)
|
||||
idx="$(find_mtd_index 0:appsblenv)"
|
||||
[ -n "$idx" ] && \
|
||||
|
||||
@ -25,9 +25,6 @@ ipq807x_setup_interfaces()
|
||||
netgear,wax218)
|
||||
ucidef_set_interface_lan "lan" "dhcp"
|
||||
;;
|
||||
prpl,haze)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
||||
;;
|
||||
qnap,301w)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g-2" "10g-1"
|
||||
;;
|
||||
|
||||
@ -22,17 +22,10 @@ case "$FIRMWARE" in
|
||||
zyxel,nbg7815)
|
||||
caldata_extract "0:art" 0x1000 0x20000
|
||||
;;
|
||||
prpl,haze)
|
||||
caldata_extract_mmc "0:ART" 0x1000 0x20000
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
"ath11k/QCN9074/hw1.0/cal-pci-0000:01:00.0.bin"|\
|
||||
"ath11k/QCN9074/hw1.0/cal-pci-0001:01:00.0.bin")
|
||||
"ath11k/QCN9074/hw1.0/cal-pci-0000:01:00.0.bin")
|
||||
case "$board" in
|
||||
prpl,haze)
|
||||
caldata_extract_mmc "0:ART" 0x26800 0x20000
|
||||
;;
|
||||
xiaomi,ax9000)
|
||||
caldata_extract "0:art" 0x26800 0x20000
|
||||
;;
|
||||
|
||||
@ -71,7 +71,6 @@ platform_do_upgrade() {
|
||||
netgear,wax218)
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
prpl,haze|\
|
||||
qnap,301w)
|
||||
kernelname="0:HLOS"
|
||||
rootfsname="rootfs"
|
||||
|
||||
@ -1,311 +0,0 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq8074.dtsi"
|
||||
#include "ipq8074-hk-cpu.dtsi"
|
||||
#include "ipq8074-ess.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "prpl Foundation Haze";
|
||||
compatible = "prpl,haze", "qcom,ipq8074";
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart5;
|
||||
/* Aliases are required by U-Boot to patch MAC addresses */
|
||||
ethernet0 = &dp6_syn;
|
||||
ethernet1 = &dp4;
|
||||
ethernet2 = &dp3;
|
||||
ethernet3 = &dp2;
|
||||
label-mac-device = &dp6_syn;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
wps-button {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset-button {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-state {
|
||||
mdc-pins {
|
||||
pins = "gpio68";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio-pins {
|
||||
pins = "gpio69";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
button_pins: button-state {
|
||||
wps-pins {
|
||||
pins = "gpio42";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
rst-pins {
|
||||
pins = "gpio44";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssphy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qusb_phy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssphy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qusb_phy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 { /* BLSP1 QUP1 */
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <0>;
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "qcom,smem-part";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
|
||||
|
||||
qca8075_1: ethernet-phy@0 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
qca8075_2: ethernet-phy@1 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
qca8075_3: ethernet-phy@2 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
qca8075_4: ethernet-phy@3 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <3>;
|
||||
};
|
||||
|
||||
aqr113c: ethernet-phy@5 {
|
||||
compatible ="ethernet-phy-ieee802.3-c45";
|
||||
reg = <8>;
|
||||
reset-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
&sdhc_1 {
|
||||
status = "okay";
|
||||
|
||||
mmc-hs400-1_8v;
|
||||
mmc-hs200-1_8v;
|
||||
mmc-ddr-1_8v;
|
||||
vqmmc-supply = <&l11>;
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_cpu_bmp = <0x1>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x1e>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x60>; /* wan port bitmap */
|
||||
switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/
|
||||
switch_mac_mode1 = <0xe>; /* mac mode for uniphy instance1*/
|
||||
switch_mac_mode2 = <0xd>; /* mac mode for uniphy instance2*/
|
||||
bm_tick_mode = <0>; /* bm tick mode */
|
||||
tm_tick_mode = <0>; /* tm tick mode */
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
phy_address = <0>;
|
||||
};
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
phy_address = <1>;
|
||||
};
|
||||
port@2 {
|
||||
port_id = <3>;
|
||||
phy_address = <2>;
|
||||
};
|
||||
port@3 {
|
||||
port_id = <4>;
|
||||
phy_address = <3>;
|
||||
};
|
||||
port@4 {
|
||||
port_id = <6>;
|
||||
phy_address = <8>;
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
ethernet-phy-ieee802.3-c45;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&edma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* Dummy LAN port */
|
||||
&dp1 {
|
||||
status = "disabled";
|
||||
phy-handle = <&qca8075_1>;
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
&dp2 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
&dp3 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_3>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
&dp4 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_4>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
&dp6_syn {
|
||||
status = "okay";
|
||||
qcom,mactype = <1>;
|
||||
phy-handle = <&aqr113c>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
&pcie_qmp0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpio = <&tlmm 58 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00020000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie_qmp1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpio = <&tlmm 61 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@1,0 {
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
status = "okay";
|
||||
|
||||
/* ath11k has no DT compatible for PCI cards */
|
||||
compatible = "pci17cb,1104";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
|
||||
qcom,ath11k-calibration-variant = "prpl-Haze";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath11k-calibration-variant = "prpl-Haze";
|
||||
};
|
||||
@ -108,18 +108,6 @@ define Device/netgear_wax218
|
||||
endef
|
||||
TARGET_DEVICES += netgear_wax218
|
||||
|
||||
define Device/prpl_haze
|
||||
$(call Device/FitImage)
|
||||
$(call Device/EmmcImage)
|
||||
DEVICE_VENDOR := prpl Foundation
|
||||
DEVICE_MODEL := Haze
|
||||
DEVICE_DTS_CONFIG := config@hk09
|
||||
SOC := ipq8072
|
||||
DEVICE_PACKAGES += ath11k-firmware-qcn9074 ipq-wifi-prpl_haze kmod-ath11k-pci
|
||||
DEFAULT_PACKAGES += ath11k-firmware-qcn9074 ipq-wifi-prpl_haze kmod-ath11k-pci
|
||||
endef
|
||||
TARGET_DEVICES += prpl_haze
|
||||
|
||||
define Device/qnap_301w
|
||||
$(call Device/FitImage)
|
||||
$(call Device/EmmcImage)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user