mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-24 05:18:14 +00:00
ath79: add support for ASUS RT-AC59U / ZenWiFi CD6
ASUS RT-AC59U / RT-AC59U v2 are wi-fi routers with a large number of alternate names, including RT-AC1200GE, RT-AC1300G PLUS, RT-AC1500UHP, RT-AC57U v2/v3, RT-AC58U v2/v3, and RT-ACRH12. ASUS ZenWiFi AC Mini(CD6) is a mesh wifi system. The unit labeled CD6R is the router, and CD6N is the node. Hardware: - SoC: QCN5502 - RAM: 128 MiB - UART: 115200 baud (labeled on boards) - Wireless: - 2.4GHz: QCN5502 on-chip 4x4 802.11b/g/n currently unsupported due to missing support for QCN550x in ath9k - 5GHz: QCA9888 pcie 5GHz 2x2 802.11a/n/ac - Flash: SPI NOR - RT-AC59U / CD6N: 16 MiB - RT-AC59U v2 / CD6R: 32 MiB - Ethernet: gigabit - RT-AC59U / RT-AC59U v2: 4x LAN 1x WAN - CD6R: 3x LAN 1x WAN - CD6N: 2x LAN - USB: - RT-AC59U / RT-AC59U v2: 1 port USB 2.0 - CD6R / CD6N: none WiFi calibration data contains valid MAC addresses. The initramfs image is uncompressed because I was unable to boot a compressed initramfs from memory (gzip or lzma). Booting a compressed image from flash works fine. Installation: To install without opening the case: - Set your computer IP address to 192.168.1.10/24 - Power up with the Reset button pressed - Release the Reset button after about 5 seconds or until you see the power LED blinking slowly - Upload OpenWRT factory image via TFTP client to 192.168.1.1 Revert to stock firmware using the same TFTP method. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
This commit is contained in:
parent
95330a5d60
commit
520c9917f8
@ -25,6 +25,10 @@ araknis,an-300-ap-i-n|\
|
||||
araknis,an-500-ap-i-ac|\
|
||||
araknis,an-700-ap-i-ac|\
|
||||
arduino,yun|\
|
||||
asus,rt-ac59u|\
|
||||
asus,rt-ac59u-v2|\
|
||||
asus,zenwifi-cd6n|\
|
||||
asus,zenwifi-cd6r|\
|
||||
buffalo,bhr-4grv2|\
|
||||
devolo,magic-2-wifi|\
|
||||
dlink,dir-859-a1|\
|
||||
|
114
target/linux/ath79/dts/qcn5502_asus.dtsi
Normal file
114
target/linux/ath79/dts/qcn5502_asus.dtsi
Normal file
@ -0,0 +1,114 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
label-mac-device = ð0;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x03000101 0x00000101 0x00001919>;
|
||||
|
||||
phy-mode = "sgmii";
|
||||
phy-handle = <&phy0>;
|
||||
|
||||
nvmem-cells = <&macaddr_factory_1002>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "sgmii";
|
||||
qca,mib-poll-interval = <500>;
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x80080080 /* PORT0 PAD MODE CTRL */
|
||||
0x08 0x00000000 /* PORT5 PAD MODE CTRL */
|
||||
0x0c 0x00000000 /* PORT6 PAD MODE CTRL */
|
||||
0x10 0x00000080 /* POWER_ON_STRAP */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
0x94 0x00000200 /* PORT6_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
reg = <0 0 0 0 0>;
|
||||
|
||||
nvmem-cells = <&precal_factory_5000>;
|
||||
nvmem-cell-names = "pre-calibration";
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
m25p,fast-read;
|
||||
|
||||
mtdparts: partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Bootloader";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "nvram";
|
||||
reg = <0x040000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "Factory";
|
||||
reg = <0x050000 0x010000>;
|
||||
read-only;
|
||||
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
cal_factory_1000: cal@1000 {
|
||||
reg = <0x1000 0x440>;
|
||||
};
|
||||
|
||||
macaddr_factory_1002: macaddr@1002 {
|
||||
reg = <0x1002 0x6>;
|
||||
};
|
||||
|
||||
precal_factory_5000: precal@5000 {
|
||||
reg = <0x5000 0x2f20>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
/* Does not work due to lack of QCN5502 support in ath9k. */
|
||||
status = "disabled";
|
||||
|
||||
nvmem-cells = <&cal_factory_1000>;
|
||||
nvmem-cell-names = "calibration";
|
||||
};
|
19
target/linux/ath79/dts/qcn5502_asus_rt-ac59u-v2.dts
Normal file
19
target/linux/ath79/dts/qcn5502_asus_rt-ac59u-v2.dts
Normal file
@ -0,0 +1,19 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcn5502_asus_rt-ac59u.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "asus,rt-ac59u-v2", "qca,qcn5500", "qca,qca9560";
|
||||
model = "ASUS RT-AC59U v2";
|
||||
};
|
||||
|
||||
&mtdparts {
|
||||
partition@60000 {
|
||||
label = "firmware";
|
||||
reg = <0x060000 0x1fa0000>;
|
||||
compatible = "denx,uimage";
|
||||
};
|
||||
};
|
19
target/linux/ath79/dts/qcn5502_asus_rt-ac59u.dts
Normal file
19
target/linux/ath79/dts/qcn5502_asus_rt-ac59u.dts
Normal file
@ -0,0 +1,19 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcn5502_asus_rt-ac59u.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "asus,rt-ac59u", "qca,qcn5500", "qca,qca9560";
|
||||
model = "ASUS RT-AC59U";
|
||||
};
|
||||
|
||||
&mtdparts {
|
||||
partition@60000 {
|
||||
label = "firmware";
|
||||
reg = <0x060000 0xfa0000>;
|
||||
compatible = "denx,uimage";
|
||||
};
|
||||
};
|
69
target/linux/ath79/dts/qcn5502_asus_rt-ac59u.dtsi
Normal file
69
target/linux/ath79/dts/qcn5502_asus_rt-ac59u.dtsi
Normal file
@ -0,0 +1,69 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcn5502_asus.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "blue:power";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "blue:usb";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&hub_port0>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "blue:wlan2g";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "blue:wlan5g";
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
};
|
57
target/linux/ath79/dts/qcn5502_asus_zenwifi-cd6.dtsi
Normal file
57
target/linux/ath79/dts/qcn5502_asus_zenwifi-cd6.dtsi
Normal file
@ -0,0 +1,57 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcn5502_asus.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
led-boot = &led_blue;
|
||||
led-failsafe = &led_red;
|
||||
led-running = &led_blue;
|
||||
led-upgrade = &led_red;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_blue: blue {
|
||||
label = "blue";
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
green {
|
||||
label = "green";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_red: red {
|
||||
label = "red";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
white {
|
||||
label = "white";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
19
target/linux/ath79/dts/qcn5502_asus_zenwifi-cd6n.dts
Normal file
19
target/linux/ath79/dts/qcn5502_asus_zenwifi-cd6n.dts
Normal file
@ -0,0 +1,19 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcn5502_asus_zenwifi-cd6.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "asus,zenwifi-cd6n", "qca,qcn5500", "qca,qca9560";
|
||||
model = "ASUS ZenWiFi CD6N";
|
||||
};
|
||||
|
||||
&mtdparts {
|
||||
partition@60000 {
|
||||
label = "firmware";
|
||||
reg = <0x060000 0xfa0000>;
|
||||
compatible = "denx,uimage";
|
||||
};
|
||||
};
|
19
target/linux/ath79/dts/qcn5502_asus_zenwifi-cd6r.dts
Normal file
19
target/linux/ath79/dts/qcn5502_asus_zenwifi-cd6r.dts
Normal file
@ -0,0 +1,19 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcn5502_asus_zenwifi-cd6.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "asus,zenwifi-cd6r", "qca,qcn5500", "qca,qca9560";
|
||||
model = "ASUS ZenWiFi CD6R";
|
||||
};
|
||||
|
||||
&mtdparts {
|
||||
partition@60000 {
|
||||
label = "firmware";
|
||||
reg = <0x060000 0x1fa0000>;
|
||||
compatible = "denx,uimage";
|
||||
};
|
||||
};
|
@ -152,6 +152,14 @@ ath79_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan:1" "2:lan:2" "3:lan:3" "6:lan:4"
|
||||
;;
|
||||
asus,zenwifi-cd6n)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan:1" "4:lan:2"
|
||||
;;
|
||||
asus,zenwifi-cd6r)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan:2" "3:lan:1" "4:lan:3" "2:wan"
|
||||
;;
|
||||
atheros,db120)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
|
||||
@ -381,6 +389,8 @@ ath79_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth1" "1:lan"
|
||||
;;
|
||||
asus,rt-ac59u|\
|
||||
asus,rt-ac59u-v2|\
|
||||
mercury,mw4530r-v1|\
|
||||
tplink,archer-a7-v5|\
|
||||
tplink,archer-a9-v6|\
|
||||
|
@ -483,6 +483,70 @@ define Device/asus_rp-ac66
|
||||
endef
|
||||
TARGET_DEVICES += asus_rp-ac66
|
||||
|
||||
define Device/asus_qcn5502
|
||||
SOC := qcn5502
|
||||
DEVICE_VENDOR := ASUS
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||||
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
||||
append-rootfs | pad-rootfs
|
||||
endef
|
||||
|
||||
define Device/asus_rt-ac59u
|
||||
$(Device/asus_qcn5502)
|
||||
DEVICE_MODEL := RT-AC59U
|
||||
DEVICE_ALT0_VENDOR := ASUS
|
||||
DEVICE_ALT0_MODEL := RT-AC1200GE
|
||||
DEVICE_ALT1_VENDOR := ASUS
|
||||
DEVICE_ALT1_MODEL := RT-AC1500G PLUS
|
||||
DEVICE_ALT2_VENDOR := ASUS
|
||||
DEVICE_ALT2_MODEL := RT-AC1500UHP
|
||||
DEVICE_ALT3_VENDOR := ASUS
|
||||
DEVICE_ALT3_MODEL := RT-AC57U
|
||||
DEVICE_ALT3_VARIANT := v2
|
||||
DEVICE_ALT4_VENDOR := ASUS
|
||||
DEVICE_ALT4_MODEL := RT-AC58U
|
||||
DEVICE_ALT4_VARIANT := v2
|
||||
DEVICE_ALT5_VENDOR := ASUS
|
||||
DEVICE_ALT5_MODEL := RT-ACRH12
|
||||
IMAGE_SIZE := 16000k
|
||||
DEVICE_PACKAGES += kmod-usb2 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += asus_rt-ac59u
|
||||
|
||||
define Device/asus_rt-ac59u-v2
|
||||
$(Device/asus_qcn5502)
|
||||
DEVICE_MODEL := RT-AC59U
|
||||
DEVICE_VARIANT := v2
|
||||
DEVICE_ALT0_VENDOR := ASUS
|
||||
DEVICE_ALT0_MODEL := RT-AC1300G PLUS
|
||||
DEVICE_ALT0_VARIANT := v3
|
||||
DEVICE_ALT1_VENDOR := ASUS
|
||||
DEVICE_ALT1_MODEL := RT-AC57U
|
||||
DEVICE_ALT1_VARIANT := v3
|
||||
DEVICE_ALT2_VENDOR := ASUS
|
||||
DEVICE_ALT2_MODEL := RT-AC58U
|
||||
DEVICE_ALT2_VARIANT := v3
|
||||
IMAGE_SIZE := 32384k
|
||||
DEVICE_PACKAGES += kmod-usb2 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += asus_rt-ac59u-v2
|
||||
|
||||
define Device/asus_zenwifi-cd6n
|
||||
$(Device/asus_qcn5502)
|
||||
DEVICE_MODEL := ZenWiFi CD6N
|
||||
IMAGE_SIZE := 16000k
|
||||
endef
|
||||
TARGET_DEVICES += asus_zenwifi-cd6n
|
||||
|
||||
define Device/asus_zenwifi-cd6r
|
||||
$(Device/asus_qcn5502)
|
||||
DEVICE_MODEL := ZenWiFi CD6R
|
||||
IMAGE_SIZE := 32384k
|
||||
endef
|
||||
TARGET_DEVICES += asus_zenwifi-cd6r
|
||||
|
||||
define Device/atheros_db120
|
||||
$(Device/loader-okli-uimage)
|
||||
SOC := ar9344
|
||||
|
Loading…
Reference in New Issue
Block a user