These got added to the kernel after this driver was written.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It automatically adds the error code at the end of the message. It also
deals with -EPROBE_DEFER automatically (doesn't output). Simpler code.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16350
Signed-off-by: Robert Marko <robimarko@gmail.com>
General hardware info:
----------------------
D-Link DGS-1210-28P rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC
@500MHz, DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE
capable with a total PoE power budget of 193W.
Power over Ethernet:
--------------------
The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU. In order to enable PoE, the
realtek-poe package is required. It is installed by default, but
currently it requires the manual editing of /etc/config/poe. Keep in
mind that the port number assignment does not match on this switch,
alway 8 ports are in reversed order: 8-1, 16-9 and 24-17.
LEDs and Buttons:
-----------------
On stock firmware, the mode button is supposed to switch the LED
indicators of all port LEDs between Link Activity and PoE status. The
currently selected mode is visualized using the respective LEDs. PoE Max
indicates that the maximum PoE budget has been reached. Since there is
currently no support for this behavior, these LEDs and the mode button
can be used independently.
Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.
Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd
OEM installation from Web Interface:
------------------------------------
1. Make sure you are booting using OEM in image 2 slot. If not,
switch to
image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image in vendor firmware via Tools > Backup / Upgrade
Firmware > image1
3. Toggle startup image via System > Firmware Information > Boot
from
image1
4. Tools > reboot
Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:
Boot initramfs image from U-Boot:
---------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000
openwrt-rtl838x-generic-d-link_dgs-1210-28p-f-initramfs-kernel.bin`
command
5. Boot the image with `bootm` command
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15938
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Before this commit, sysupgrade saved the settings backup data to
the area following rootfs even though the device has an actual
rootfs_data partition. The backup data was completely ignored on
the following boot, but since rootfs_data was not being cleared
during sysupgrade, the issue was not noticed earlier.
Note that this commit changes the filesystem of rootfs_data from
ext4 to F2FS (if OEM partitioning is used).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16463
Signed-off-by: Robert Marko <robimarko@gmail.com>
This board is also as known as Bananapi BPi-M7.
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
8/16/32GB LPDDR4/LPDDR4x RAM
2x 2500 Base-T (PCIe, rtl8125b)
2 LEDs (RED / GREEN)
16GB/32GB/64GB/128GB eMMC on-board
Micro-SD Slot
USB 2.0 Port
USB 3.0 Port
M.2 M-Key
40-Pin Header
USB PD 2.0 9/12/15V Power
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16462
Signed-off-by: Nick Hainke <vincent@systemli.org>
of_property_read_u32 returns -EINVAL when property does not exist,
according to the documentation -ENOENT is not a valid return code.
So, instead of checking for -ENOENT check for -EINVAL as otherwise the
blamed commit breaks AQR probe since it will return -EINVAL during probe.
Fixes: cb2a11f49c ("generic: phy: aquantia: add pending patch to force MDI pair order")
Link: https://github.com/openwrt/openwrt/pull/16466
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing ksym CONFIG_RUST
Building r27563 without this commit will fail due to this ksym
being undefined in the generic config.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16464
Signed-off-by: Robert Marko <robimarko@gmail.com>
We already have an kernel module package "kmod-phy-ath79-usb" to
drive the ath79 USB. It will be selected by the usb base package
"kmod-usb2" and "kmod-usb-ohci".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.
The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)
Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:
https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/
The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.
http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.
Alternatively, from a root shell on the running system, unlock the boot
partition with
echo 0 >/sys/block/mmcblk0boot0/force_ro
then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.
Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset
USB: Front V3.0 & Rear V2.0
MAC Table
Label xx:xx:xx:xx:xx:38
LAN xx:xx:xx:xx:xx:39
2.4Ghz xx:xx:xx:xx:xx:3A
5Ghz xx:xx:xx:xx:xx:3C
WAN xx:xx:xx:xx:xx:38
Flash Instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image
D-Link Fail Safe GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the fail safe GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the fail safe page for the device at http://192.168.0.1/
6. Use the provided fail safe web GUI to upload the factory.bin to the device
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16269
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Only one device uses the dtsi file "rt3883_belkin_f9k110x.dtsi".
So there is no need to split the device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16318
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 GHz WiFi doesn't work on the wmac of this device.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16318
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for W25N01JW, W25N02JWZEIF, W25N512GW, W25N02KWZEIR and W25N01GWZEIG.
Add support for W25N04KV.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16272
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SoC: MediaTek MT7621
Flash: 16MB (Macronix MX25L12805D)
RAM: 128MB
Serial: As marked on PCB, baudrate is 57600, DO NOT CONNECT 3.3V!!!
Ethernet: 4x 10/100/1000 Mbps (3x LAN + WAN)
WIFI0: MT7615 2.4GHz 802.11b/g/n
WIFI1: MT7615 5GHz 802.11ac
Antennas: 6x external (3 per radio), non-detachable
LEDs: Programmable power-LED (blue-colored)
Buttons: Reset
INSTALLATION:
Get rootshell using insructions from https://gist.github.com/ZIKH26/18693c67ee7d2f8d2c60231b19194c37
Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Download archive with firmware from Ruijie's site and
get .bin file from it. Then write that binary to firmware
partition. After reboot, factory-reset the router using
reset button.
Signed-off-by: Yahor Leonenka <staryjakau@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16202
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WSC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh extender,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 2x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/2x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 10.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:6E (Factory, 0x3fff4 (hex))
2.4 GHz: 04:AB:18:xx:xx:6F (Factory, 0x3fffa (hex))
5 GHz : 04:AB:18:xx:xx:70 (Factory, 0x4 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WMC-X1800GST is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh router,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 3x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/5x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:BF (Factory, 0x3fff4 (hex))
WAN : 04:AB:18:xx:xx:C0 (Factory, 0x3fffa (hex))
2.4 GHz: 04:AB:18:xx:xx:C1 (Factory, 0x4 (hex))
5 GHz : 04:AB:18:xx:xx:C2
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename the downstream ag71xx driver to ag71xx-legacy.
It allows both upstream and downstream drivers to be compiled into modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware Spec
-SoC: Rockchip RK3588S
CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
-RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
-Flash: 32GB/None eMMC, at HS400 mode
-Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
-USB: one USB 3.0 Type-A and one USB 2.0 Type-A
-PCIe: one M.2 Key M connector with PCIe 2.1 x1
-HDMI:
compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
support up to 7680x4320@60Hz
Support RGB/YUV(up to 10bit) format
-microSD: support up to SDR104 mode
-GPIO:
30-pin 2.54mm header connector
up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
-Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
-LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
-others:
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
MASK button for eMMC update
one user button
-Power supply: USB-C, support PD, 5V/9V/12V/20V input
-PCB: 8 Layer, 62x90x1.6mm
-Ambient Operating Temperature: 0℃ to 70℃
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
eMMC Installation:
Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport ir-receiver/minipcie/poweroff/spi/usb-c support and other
minor fixes for the NanoPC T6 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16443
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update sysupgrade script (fortinet.sh) for Fortinet devices in
mvebu/cortexa9 and fix the following issues,
- Some individuals of FortiGate/FortiWiFi 30E/5xE devices has wrong
kernel/rootfs offsets in "firmware-info" partition and they are not
updated with the current sysupgrade script for Fortinet devices
(fortinet.sh).
As a result, the bootloader tries to load kernel data from the wrong
address and boot with it after OpenWrt installation.
The new script handles offsets in addition to length values.
and improve the following points.
- Only 2 bytes are handled with the current sysupgrade script
(fortinet.sh) for kernel/rootfs length. The new script handles 4 bytes
instead.
- The image names of image0/image1 are not handled and not updated when
sysupgrade. The new sysupgrade script handles it and update to
"<dist> <version> <revision>" if firmware metadata is available.
(ex.: "OpenWrt SNAPSHOT r27440-25384026")
log of new sysupgrade script (fortinet.sh):
Tue Sep 17 10:29:16 UTC 2024 upgrade: Performing system upgrade...
Image Index: 0
Image Name : "OpenWrt SNAPSHOT r27440-25384026"
--> "OpenWrt SNAPSHOT r27441-b3a0806a05"
kernel:
old: 0x003c4e00@0x00200000
new: 0x003c4e00@0x00200000
rootfs:
old: 0x005c0200@0x00800000
new: 0x005c0200@0x00800000
Unlocking kernel ...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mdio bus number of mv88e6xxx was changed to '0' from '1' and the
"mv88e6xxx-1:<addr>:<speed>" triggers are unavailable now.
Update triggers for "SPEED" LEDs to make working that LEDs again.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver for fixed voltage regulater uses "regulator-fixed" for
compatible string, not "fixed-regulator".
Fixes: 102dc5a625 ("mvebu: add support for FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename the sysupgrade.tar step to sysupgrade.bin. The sysupgrade.tar is
used in other places and we prefer a sysupgrade.bin instead.
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.
This fixes the build of the ramips target.
Fixes: 665c2154ef ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change I2C pin flags to GPIO_ACTIVE_HIGH and change SDA to GPIO1.
On my late production GL-AR750 (purchased 2024):
SCL = GPIO16
SDA = GPIO1
Bug report:
I2C bus doesn't work in GL-AR750
https://github.com/openwrt/openwrt/issues/16319
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16406
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make the patches apply cleanly again.
Fixes: 3660ddb8ab ("generic: ar8216: remove support for Linux before version 6.1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification is similar to other devices of the MT Stuart series:
* Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 2500M/1000M/100M LAN port
* 10000M/5000M/2500M/1000M/100M/10M WAN port
* MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for the 2.5G port, 3x LED for the 10G port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The legacy swconfig switch driver framework supports kernels older than
Linux 6.6 by using #ifdef'ery with LINUX_VERSION_CODE. Remove all that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove folder with DTS files for Linux 6.1 which has already been
dropped.
Fixes: f142ce87d9 ("kirkwood: remove 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Support for Linux 6.1 has already been removed from the armsr target.
Remove left-over patches-6.1 folder as well.
Fixes: fd47fdf527 ("armsr: Remove kernel 6.1 configuration")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove left-over config-6.1 files which should have been removed
when removing kernel 6.1 support.
Fixes: f20987c161 ("layerscape: remove kernel 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the GPIO pin of the PoE passthrough switch on the Aruba AP-303H.
Power is activated when the pin is low. It enables a PSE chip, so power
is only supplied to downstream devices when they are 802.3af/at
compliant devices.
Ensure you use a sufficient power supply when chaining a consuming
device after the AP.
Signed-off-by: David Bauer <mail@david-bauer.net>
Increase QDMA RESV_BUF from 2K to 3K for netsys v2 to match Mediatek SDK.
This helps reduce the possibility of Ethernet transmit timeouts.
Link: 19d8456c30
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The purpose of resetting the TX queue is to reset the
byte and packet count as well as to clear the software
flow control XOFF bit.
MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.
Packets may stop being sent after reset and "transmit timeout" log may
be displayed.
Import fix from MediaTek's SDK to resolve this issue.
Link: 5746a94456
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This files are executable:
target/linux/ramips/dts/mt7621_openfi_5pro.dts
target/linux/ramips/dts/mt7621_winstars_ws-wn536p3.dts
Has to be fixed.
Fixes: 5560791 ("ramips: add support for OpenFi 5Pro Travel Router")
Fixes: 2da2705 ("ramips: add support for WINSTARS WS-WN536P3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of reading it from flash directly, let U-Boot assign the LAN
MAC address. Set label-mac-device while at it and sort aliases in DT
alphabetically.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kconfig symbols CONFIG_VIDEO_MICROCHIP_CSI2DC, CONFIG_VIDEO_MICROCHIP_ISC
and CONFIG_VIDEO_MICROCHIP_XISC are missing for sama5 and sama7 causing
the build to abort or waiting for user input. Add the symbols (disabled)
so build with Linux 6.6 succeeds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix a typo in the MAC address assignment script affecting SDG-8734.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware information:
---------------------
- SoC: RTL8393M
- Copper phy: 6×RTL8218B
- Fibre phy: RTL8214FC
- Flash: 32MiB SPI NOR, MX25L25635FMI
- RAM: 128MiB DDR3, Micron MT41K64M16TW-107
- Serial port: ±5V serial port to RJ45, ZT3232 (MAX3232 compatible)
- +370W POE on JG928A model
Note: SFP ports currently non-functional due to missing support for
RTL8214FC on the RTL8393M target.
Updated for Linux 6.6 kernel.
Installation:
-------------
- Initial installation follows same process as HPE 1920-24G (JG924A)
- Based on prior work of Jan Hoffmann <jan@3e8.eu>
- Additional work by Andreas Böhler <dev@aboehler.at>
- PoE updates and tidy-up by Stephen Howell <howels@allthatwemight.be>
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Now that there is 6.6 support for realtek, lets encourage testing it by
making it default so 5.15 can be dropped ASAP.
Link: https://github.com/openwrt/openwrt/pull/16408
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 'active-low' property was not applied correctly and two fixes
are required to make inverted LEDs work as expected.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The at91 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove obsolete patches no longer applicable to the 6.6 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove unnecessary dts files already included in the 6.1 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Siflower SF19A2890 is an SoC with:
Dual-core MIPS InterAptiv at 800MHz
DDR3 controller
One Gigabit Ethernet MAC with RGMII and IPv4 HNAT engine
Built-in 2x2 11N + 2x2 11AC WiFi radio
USB 2.0 OTG
I2C/SPI/GPIO and various other peripherals
This PR adds support for SF19A2890 EVB with ethernet support.
EVB spec:
Memory: DDR3 128M
Ethernet: RTL8367RB 5-port gigabit switch
Flash: 16M NOR
Others: MicroUSB OTG, LED x 1, Reset button x1
The built image can be flashed using u-boot recovery.
This target is marked as source-only until support for a commercial
router board comes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].
[0] https://forum.openwrt.org/t/206640
Signed-off-by: Andreas Böhler <dev@aboehler.at>
RELR is a relocation packing format for relative relocations.
Linux has supported using it for ARM64 since 5.4, and more recently
for LoongArch as well.
It requires compatible tooling as well, so only with binutils 2.43
TOOLS_SUPPORT_RELR is set and thus RELR available.
RELR should always decrease the binary size and while testing this
the default build for Dynalink WRX-36 (qualcommax/ipq807x) reduced
the compressed kernel size by 38k and uncompressed one by 640k.
So, lets enable it in the default config.
Link: https://github.com/openwrt/openwrt/pull/16403
Signed-off-by: Robert Marko <robimarko@gmail.com>
Merging of the realtek 6.6 series forgot to include some final fixes
for the new MDIO driver. What was changed in last second?
1. The MDIO driver used wrong constants to make use of the raw
page (for direct register access). Provide a rawpage variable in
the bus private structure, populate it during initialization and
make use of it at the proper places
2. We always used the variable portaddr for the bus index. Usually
our driver uses either addr or port for the same meaning. Remove the
duplication and reuse the normal addr variable.
3. Drop functions rtmdio_write_page() and rtmdio_read_page(). These
only call the PHY driver read/write page functions. We know that
these will only access page 0x1f. As we have only Realtek PHYs
and our driver only reacts to this special page, just hardcode it.
Benefit is that we can use these functions for PHY detection when
read/write page functions are not yet assigned.
4. Add two new helper functions phy_port_read_paged() and
phy_port_write_paged(). These allow to access arbitrary ports on
the MDIO bus when the packages are not initialized. These will be
needed for proper RTL8218B and RTL8214FC detection in forthcoming
patches.
5. The port tracking wrongly used index 0 to mark "normal" access.
This does not allow to make a "special" access to port 0. Use
index -1 to mark "normal" access.
Provide the fix for 5.15 and 6.6 to allow for easy version
comparison.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
With commit a22d359fa5 VLAN handling was fixed for kernel 6.6.
This restored network connectivity of the devices. For easy testing
backport the fix for 5.15 too.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
On the XGS1210-12 the RTL8218D is attached via XGMII. Add this to the
supported list in the DSA driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
We switched to 6.6, so lets remove 6.1 support now.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unset CONFIG_CRYPTO_MANAGER_DISABLE_TESTS and
CONFIG_CRYPTO_MANAGER_EXTRA_TESTS manually to fix these linker errors:
crypto/crypto_engine.o: in function `crypto_engine_register_akcipher': undefined reference to `crypto_register_akcipher'
crypto/crypto_engine.o: in function `crypto_engine_unregister_akcipher': undefined reference to `crypto_unregister_akcipher'
crypto/crypto_engine.o: in function `crypto_engine_register_kpp': undefined reference to `crypto_register_kpp'
crypto/crypto_engine.o: in function `crypto_engine_unregister_kpp': undefined reference to `crypto_unregister_kpp'
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
.dts files were moved to the 'ti/omap' sub-directory.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bring it in line with all the other targets.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DGS-1210-28MP has a LM63 fan controller connected via i2c of the
RTL8231. The clock line is always low if the property
i2c-gpio,scl-open-drain is not set; with this property, the GPIO pin is
force-drive and the clock works as expected.
The LM63 is not configured by U-Boot, thus only manual fan control is
possible by settings pwm1_enable to "1" and writing the desired values to
pwm1.
The OEM firmware drives the fan from user mode and sets it up like this:
// PWM LUT/value r/w, PWM Clock = 1.4kHz
0x4a 0x28
// Tachometer spinup disabled, spin-up cycles bypassed
0x4b 0x00
// PWM Frequency = default
0x4d 0x17
// PWM Value (28)
0x4c 0x1c
// If > 0 C, use
0x50 0x00
// PWM = 28
0x51 0x1c
// If > 51 C, use
0x52 0x33
// PWM = 44
0x53 0x2e
// Set hysteresis to 100 = default
0x4f 0x03
// Turn on automatic mode and w/p the LUT values
0x4a 0x08
A thread in the OEM firmware polls the ALERT status register for fan
failures.
Unfortunately, the lm63 kernel driver does not perform any initialization
of the chip and it does not support changing some config registers (like
PWM frequency or LUT). Hence, we are stuck with the defaults and need to do
fan control in software.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/15616
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The DGS-1210-28 series was lacking full SFP support due to missing GPIOs.
Fortunately, the existing GPIO definitions of DGS-1210-52 match, this adds
the required i2c-gpio nodes to the DTS and allows hotplug SFP support.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/15616
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The one for the mx60 was wrong. The LAN MAC is offset by one.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14037
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qca8k driver is upstream, unlike swconfig. This applies to the mx60
and wndr4700 only. Fixed up LED definitions as well.
RTL83xx DSA for WNDAP62300/660 is not working.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14037
Signed-off-by: Robert Marko <robimarko@gmail.com>
The CPU port of realtek switches needs some proper PVID set to handle
untagged packets. Because the ethernet driver does no special VLAN
handling (see CPU tag RVID/RVID_SEL) as of now we can only steer
untagged packets by setting PVID for the CPU port. VLAN handling has
never been perfect but 3 events made things worse.
- Commit a376508216 ("rtl83xx: dsa: Do nothing when vid 0")
- Commit e691e2b302 ("rtl83xx: dsa: reset PVID to 1 instead of 0")
- Upgrade to kernel 6.6
Reasons are:
- Rejecting VID 0 disabled Linux initialization routines
- Initialization for PVID forgot to set priv->ports[port].pvid
- Kernel 6.6 does no longer clarify CPU port as untagged
To fix this prepare the VID 0 setup inside the driver. Join all ports
to VID 0 and let no one from outsinde interfere with this setup.
Especially ignore PVID settings for the CPU port for all further
VLAN commands.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Since kernel commit c5714f68a76bcad3d ("net: phylink: explicitly invalidate
link_state members in mac_config") it should be clear that link data can
only be used in mac_link_up(). Refactor that for the RTL83xx targets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Some devices (e.g. HP JG924A) hand over other than expected kernel boot
arguments. Looking at these one can see:
fw_init_cmdline: fw_arg0=00020000
fw_init_cmdline: fw_arg1=00060000
fw_init_cmdline: fw_arg2=fffdffff
fw_init_cmdline: fw_arg3=0000416c
Especially fw_arg2 should be the pointer to the environment and it looks
very suspicous. It is not aligned and the address is outside KSEG0 and
KSEG1. Booting the device will result in a hang. Do better at verifying
the address.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Suggested-by: Bjørn Mork <bjorn@mork.no>
The supported_interfaces bitmap cannot be empty since mainline kernel
commit de5c9bf40c45 ("net: phylink: require supported_interfaces to
be filled"). Fix the dsa and ethernet driver accordingly.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The DSA framework has changed a bit since 6.1, lets adapt to match.
Currently there is no one-patch-fits-all solution to directly fix
all errors up to 6.6. So cover the final differences with this
second patch.
Most notable upstream changes are:
- a88dd7538461 ("net: dsa: remove legacy_pre_march2020 detection")
- 53d04b981110 ("net: dsa: remove phylink_validate() method")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[Minor checkpatch.pl cleanups]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The DSA framework has changed a bit since 5.15, lets adapt to match.
Currently there is no one-patch-fits-all solution to directly fix
all errors up to 6.6. So at least take all the already known changes
that cover differences between 5.15 and 6.1
Most notable upstream changes are:
- d3eed0e57d5d ("net: dsa: keep the bridge_dev and bridge_num as part
of the same structure")
Update of port_bridge_{join,leave}: use same helper as upstream
- c26933639b54 ("net: dsa: request drivers to perform FDB isolation")
Update of port_fdb_{add,del}, port_mdb_{add,del}
- dedd6a009f41 ("net: dsa: create a dsa_lag structure")
Update of port_lag_{join,leave}
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[align updates with upstream, add references to upstream commits]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Only take over the new patch locations. All errors
that wil arise from compiling with the phy driver will be covered by
follow up patches.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Only adapt the failing hooks and take over the
new patch locations. All errors that wil arise from compiling with
the dsa driver will be covered by follow up patches.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
A lot of stuff has been converted to the phylink_pcs_ops structure.
Adapt the ethernet driver to make use of it.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
We no longer are required to pass the weight to netif_napi_add.
See commit b48b89f9c189 ("net: drop the weight argument from netif_napi_add").
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
This is not a surprise. Before upgrade to 6.6 we refactored the mdio part of
the ethernet driver and knew that changes will come. Drop all unnecessary
stuff from the old world and adapt to the new kernel.
- remove legacy functions
- directly link new functions
- adapt to new shared base address
- remove references to old MDIO bus capabilities
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Only take over the new patch locations. All errors
that will arise from compiling with the ethernet driver will be covered
by follow up patches.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
With the new kernel the MDIO bus gets created after the smbus
read/write functions are used. Make use of native functions.
Relocate bus initialization into a separate function to make
patch easier to read.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Take over the new patch locations and add references to the link mode into
phylink_sfp_interface_preference[] and phylink_get_capabilities().
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. As the order of the 7xx patch files seems very
strange reorder all of them according to the realtek 6.6 kernel upgrade
effort.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Only take over the new patch locations.
With this patch all platform specific changes for kernel 6.6 are in place.
Realtek devices are bootable from serial console. VPE is fully functional
on devices that support it. The switch functions (ethernet and DSA) are
not enabled yet.
Boot tested on RTL8380 (Linksys LGS310C) and RTL8393 (Zyxel GS1920-24).
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
VPE in mainline kernel has changed a lot. This patch wraps up the 5.15
patch files and rebases them in one single patch on top of kernel 6.6.
Former patches are
315-irqchip-irq-realtek-rtl-add-VPE-support.patch
319-irqchip-irq-realtek-rtl-fix-VPE-affinity.patch
Submitted-by: Birger Koblitz <git@birger-koblitz.de>
Submitted-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Copy the patch files to 6.6. Both target drivers/irqchip/irq-realtek-rtl.c
and are additions and fixes for IRQ VPE handling.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Copy the patch file to 6.6. No further processing required as
it applies cleanly to the new kernel
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Due to kernel changes the patch hooks totally failed
and had to be fixed manually.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The CONFIG_CLOCKSOURCE_WATCHDOG_MAX_SKEW_US is missing. Avoid
complaints and add it with its default 125.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Copy files and config from 5.15 kernel version. Because of the big version jump
leave out the patches for now so we can treat them individually later on.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
With commit b53202a8c3 ("realtek: switch to use generic MDIO accessor functions")
the phy access logic was enhanced. A quite big kernel patch was introduced that
allowed to make use of hardware-assisted page access like we have in the realtek
target. Basically it works the following way
- The enhanced bus intercepts page write accesses
- Currently selected pages are stored in internal vars.
- Finally only all-in-one-consistent bus/register accesses are issued
- It intercepted page changes and ensured that only a complete bus call
For the details see https://github.com/openwrt/openwrt/pull/16172
Switching over to newer kernels this patch is really hard to maintain. Its heavy
modifcations exist only in the realtek target. So it does not matter if we keep
it as an kernel modification or directly include it in our driver. To make it the
future brighter we drop this patch and take over its logic. Thus the kernel will
stay totally modification-free. What do we do?
1. Up to now the bus->priv structure directly pointed to ethernet->priv. Create an
explicit private structure rtl838x_bus_priv that not only holds the ethernet->priv
pointer but also space for some bus status tracking vars as well.
2. Wherever we use a reference to ethernet->priv directly replace that by an
additional indirection over the new rtl838x_bus_priv structure.
3. Up to now the phy flag PHY_HAS_REALTEK_PAGES identified that we can use the
alternative paged access from the patch. As this will be no longer available
remove it and provide read_page/write_page functions for each possible PHY.
These functions will be pretty standard as for other Realtek PHYs.
4. The existing mdio bus read/write function rely on the classic MII_ADDR_C45
flag - one interface for two access types. This mixup will be removed on the way
to kernel 6.6. In the future there will be two pairs of access functions. One for
classic access one for c45 style access. Rewrite our functions into 3 parts:
- a classic read/write function: ready for kernel 6.6
- a new c45 read/write function: ready for kernel 6.6
- a legacy read/write wrapper: for current 5.15 for the time being
When we switch to 6.6 we only need to remove the legacy wrappers and link the
new functions. Life can be so easy.
5. The classic read/write functions will incorporate the interception logic that
was originally in the patch.
6. The package convenience functions that were embedded in the patch get lost as
well. Rewrite them inside our phy driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[Minor checkpatch.pl cleanups]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
There is no need to keep a version specific dts directory.
Rename the folder to its standard location.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Apply changes suggested by SkyLake Huang for pending series improving
MediaTek Ethernet PHY drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Aruba boards now ship with multiple DTS and image-configurations per
image. Newer apboot revs expect a configuration for their hardware to be
present.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.
Fixes: e497c975d3 ("ramips: mt76x8: add support for Yuncore M300")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.
Fixes: 64dae1052b ("ramips: mt76x8: add support for Yuncore CPE200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
And remove support for 6.1 while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15838
Signed-off-by: Robert Marko <robimarko@gmail.com>
A rather trivial addition. Patches automatically rebased. Also add the new
CONFIG_USB_DWC3_OCTEON (disabled) to the generic 6.6 config and sort it, while
at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15838
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>
This enables the M.2 E-key on ROCK 5A board.
Reorder rk356x patch while at it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16340
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
This alias was present in 6.1. Add back to restore a fully working console after
sbi0 (earlycon) gets disabled during the boot process.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Various cleanups and bugfixes were applied.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16215
Signed-off-by: Robert Marko <robimarko@gmail.com>
No reason for them not to be so. Matches various upstream commits for
PPC.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>
With upstream commit 0aafbdf35c75cbfec82636d01e6dc7950bc1507c , this is
now default. No need to override.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit does this for simple cases, which all of these are.
Commit: 1c96fcdef8c7492ecf34ed70102a1ae5253ef9d1
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>
configure 2.5G PHY LEDs to:
2500/1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
which is similar to other 1G PHY LEDs, which are:
1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
Fixes: 6cc14bf66a ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This commit adds the logic required to install OpenWrt on a
Cisco/Viptela vEdge 1000 while nicely integrating with the already
present bootloader and making it possible to roll back to stock OS.
The vEdge 1000 has a built-in SSD with a ext2 partition from which
the stock u-boot boots the Linux kernel from.
In order for Linux not to be confused about which partition the root
file system is on, there are some tricks needed to ensure the partition
is identifiable at boot time. For this we use blkid as part of the
scripts, and sfdisk as part of the manual installation process
documented on the wiki. Thus, those packages have been added as a
platform dependency. Finally, the u-boot environment is updated which
requires the use of uboot-envtools.
Tested on a Cisco vEdge 1000.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Link: https://github.com/openwrt/openwrt/pull/16140
Signed-off-by: Robert Marko <robimarko@gmail.com>
Yuncore CPE200 is an outdoor unit with IEEE 802.11ac radio.
Hardware:
- SoC: MediaTek MT7628DAN (MIPS 580MHz)
- Flash: 8 MiB Spansion S25FL064K
- RAM: 64 MiB (built-into SoC)
- WLAN: 5 GHz (MT7613AE)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- Buttons: 1 Reset button, 2 buttons for display UI (unsupported)
- LEDs: 4x Green (Power, LAN, WAN, WiFi)
- Display: 4 digit 7-segment display driven by an additional
microcontroller (unsupported)
- Serial console: unpopulated header, 57600 8n1 (RX only)
- Power: 12 VDC, 1 A
Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.0.100/ and upload sysupgrade.bin file.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
er is missing from platform_copy_config() and octeon_move_config(), so
config is lost on every sysupgrade.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/16238
Signed-off-by: Robert Marko <robimarko@gmail.com>
MediaTek SDK uses eth2 as additional LAN port and eth1 as WAN.
Do the same also in OpenWrt to keep settings aligned with the SDK.
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16057
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16057
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Unused wan mac added to dts. Requires DSA to implement.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get vlan 4k for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get mc index for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get ports speed for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Detect the RTL8367D chip family and set the appropriate extif
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disables Data Center Bridging support for some network drivers by
default to avoid compilation errors when CONFIG_DCB is enabled.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3B is a Pico-ITX form factor SBC[1] using the Rockchip
RK3568(J).
Hardware
--------
- Rockchip RK3568(J) SoC
- Quad A55 CPU
- Mali-G52 GPU
- 1 TOPS @ INT8 NPU
- 2GB/4GB/8GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key (2-lane PCIe 3.0)
- SPI Flash for bootloader
- 2x Gigabit ethernet port (one supports PoE with add-on PoE HAT)
- 1x M.2 E Key socket with SDIO, UART and USB interfaces
- 1x M.2 B Key socket with PCIe, SATA, and USB interfaces
- 1x SIM card socket
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST ports
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3b
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3C is a high-performance, low-cost SBC[1] using the
Rockchip RK3566.
Hardware
--------
- Rockchip RK3566 SoC
- Quad A55 CPU
- Mali-G52-2EE GPU
- 1 TOPS @ INT8 NPU
- 1GB/2GB/4GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key connector(2230) or M.2 Extension
board(2232/2260/2280)
- SATA through the Radxa Penta SATA HAT
- 1x Gigabit ethernet port(supports PoE with add-on PoE HAT)
- WiFi6/BT5.4 (not supported yet on OpenWrt)
- 1x USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- 1x USB 2.0 Type-A OTG port
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3c
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All boards using the deprecated uImage.FIT partition parser have
been migrated to the new fitblk driver. Drop the now no longer
needed partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
That patch title of 911-kobject_add_broadcast_uevent.patch has been
wrongly copied from 910-kobject_uevent.patch.
Change the description from "lib: add uevent_next_seqnum()" to
"lib: add broadcast_uevent()", so that the git history doesn't look
all weird when importing both patches to a git tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes model name in dts as below:
Radxa ROCK3 model A -> Radxa ROCK 3A
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16232
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Like x86, armsr is frequently virtualized, and is used for development
and debugging. Kernel messages should be more readily apparent by
default. This can be achieved by adding console=tty1 to the kernel
command line, enabling the console on a (possibly virtual) display and
keyboard, in addition to a serial port.
This also enables failsafe on tty1. Failsafe mode operates on consoles
known by the kernel, without regard to /etc/inittab.
armsr's /etc/inittab is also updated to specify tty1 instead of tty0.
tty1 is technically more correct: tty1 is the first virtual console,
where tty0 reflects the current active virtual console (which is likely
to be tty1).
This configuration matches x86, which is another target commonly used
for virtualization, development, and debugging in the same way. x86's
kernel command line had specified console=tty0, although console=tty1 is
more correct for the reasons given above. This also brings x86's kernel
command line console= into agreement with its /etc/inittab, which
already used tty1.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16213
Signed-off-by: Robert Marko <robimarko@gmail.com>
Found with coccinelle:
No need to set .owner here. The core will do it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16217
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link TD-W8968 v3 is an 300Mbps Wireless N USB ADSL2+ Modem Router based on
Broadcom BCM6318 SoC.
Hardware:
CPU: Broadcom BCM6318, 333 MHz, 1 core
Flash: 8MB
RAM: 64 MB
Ethernet: 4x 10/100 Mbps
Wireless: 802.11b/g/n, BCM43217
LEDs/Buttons: 10x / 3x
USB: 1x 2.0
Flash instructions:
* Assign static IP 192.168.1.100 to PC
* Unplug the power source
* Press the RESET button at the router, don't release it yet!
* Plug the power source. Wait for some seconds
* Release the RESET button
* Browse to http://192.168.1.1
* Upload the openwrt-bmips-bcm6318-tp-link_td-w8968-v3-squashfs-cfe.bin file
* Wait some minutes until the firmware upgrade finish.
Signed-off-by: Mathesh Velayudan <123v.mathesh@gmail.com>
Device support for Sophos AP15 is based on Sophos AP55(C) and AP100(C).
Those other Sophos access points uss a QCA9558 SoC (some of them with
one of the three chains on the built-in SoC's wifi disabled) while the
AP15 uses a QCA9557 SoC (which only has two chains enabled in the
package or silicon).
This is mostly cosmetic since QCA9558 and QCA9557 are virtually
identical and all differences are automatically detected and/or managed
by the ART calibration.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/16187
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16230
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit introduces led nodes in tl-wdr4900-v1 dts.
It allows to configure switch leds from userspace.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link tl-wdr4900-v1 has two usb leds. Modern kernels can handle usb
led trigger. Let's enable it.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit change led description in dts file from old method to new
approach accepted by upstream.
USB power gpio is handled by gpio-export now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
Ever since CONFIG_ARM64_PAN was enabled Common Not Private (CNP) is now
visible and kernel builds will stop as they are not set in kernel config
for 5.15 and 6.1.
So, lets enable Common Not Private (CNP) which is ARMv8.2 feature and will
be NOP of CPU-s that dont support it.
Fixes: a2662309aa ("kernel: Enable CONFIG_ARM64_PAN to restrict kernel access to user space memory")
Link: https://github.com/openwrt/openwrt/pull/16211
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enhanced Privileged Access Never (EPAN) is an ARMv8.7 feature, and since
we dont have any SoC-s implementing it lets disable it.
Link: https://github.com/openwrt/openwrt/pull/16211
Signed-off-by: Robert Marko <robimarko@gmail.com>
The commit backporting new MTK patches did not update the
Kernel config for mediatek/mt7622 causing the build to
fail.
Simply use the new config symbol name for the driver to
fix the issue.
Fixes: 1069514978 ("mediatek: backport pending Ethernet PHY driver patches")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/16225
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use pending patchset for 2.5GE PHY driver, unifying LED handling
accross all MediaTek Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kconfig symbols CONFIG_ARM64_CNP and CONFIG_ARM64_EPAN got exposed
by enabling CONFIG_ARM64_PAN. Enable them as well, as just like for
PAN, also EPAN and CNP will be detected at runtime at no cost.
Fixes: a2662309aa ("kernel: Enable CONFIG_ARM64_PAN to restrict kernel access to user space memory")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
No benefit in doing so in platform file. Code for dts has already been
written. Might as well use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated. No need for any of this.
Calibration size was adjusted to 440, which is the standard value for
ath9k radios.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that the ports are defined in DTS, this is trivial to do.
Avoids userspace handling.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
The kernel support necessary to use a console keyboard was not built on
x86, affecting real and virtual machines alike. The console keyboard
would function properly in GRUB, but would not work at all once Linux
booted. It appeared that the console was intended to work because
console video appeared on the display, including prompts to enter
failsafe or select the debug log level from the keyboard, and the prompt
to "Press Enter to activate this console", but there was no way to
provide input to it. All keystrokes were ignored.
This enables several kernel configuration options to enable HID and USB
HID support (CONFIG_HID, CONFIG_HID_SUPPORT, CONFIG_HID_GENERIC, and
CONFIG_USB_HID), making the keyboard functional. For alignment with
armsr, CONFIG_USB_HIDDEV is also added, although not strictly necessary
for keyboard support. Note that this change also causes
CONFIG_HID_HYPERV_MOUSE to be enabled for x86/64 and x86/generic: it was
already set in these subarchitectures' kernel configurations, but was
ineffective due to CONFIG_HID being absent.
The omission of keyboard support on x86 may not have been widely noticed
because USB HID is not used on production OpenWrt x86 machines such as
pc-engines,apu2 which only have a serial console, or with the default
x86 configuration used by scripts/qemustart, which uses -nographic and
does not configure a virtual physical console but instead uses a serial
console.
This configuration change results in, for x86_64, +40kB in kernel.bin
and just over +40kB in gzip-compressed "combined" images. This should
not be a problem for the non-storage-constrained x86 target.
Until 2a86425de1, CONFIG_HID, CONFIG_USB_HID, and CONFIG_USB_HIDDEV
were set in the target-level kernel configuration, and
CONFIG_HID_GENERIC was set at the subtarget level. These are
reintroduced strictly at the subtarget level by request. This applies to
the 64, generic, and legacy subtargets, omitting geode.
Fixes: https://github.com/openwrt/openwrt/issues/16157
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16208
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable the CONFIG_ARM64_PAN kernel security option, which leverages the
ARMv8.1 Privileged Access Never (PAN) extension to prevent the kernel
from directly accessing user space memory.
Instead, copy_to_user and similar functions must be used for data
transfer between kernel and user space. This feature is automatically
disabled at runtime on CPUs without PAN support, making it a no-op in
those cases.
Link: https://github.com/openwrt/openwrt/pull/16189
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Activate the kernel option CONFIG_LIST_HARDENED for all targets.
This adds some inline checks to list_add() and list_del() operations
in the kernel. Before kernel 6.6 these checks were only available with
CONFIG_DEBUG_LIST option, but now a light version is available which
should only add very few extra instructions to such operations.
The performance penalty is very low from my point of view. It should
make it much harder to use bugs in Linux kernel list handling when
exploiting the Linux kernel.
Link: https://github.com/openwrt/openwrt/pull/16189
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
2500 Base-T
RGB LED
eMMC Connector
SPI-NOR 16MB
Micro-SD Slot
2x USB 2.0 Port
2x USB 3.0 Port
Headphone Jack
M.2 E-Key
M.2 M-Key
USB PD 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
1000 Base-T
Status LED
eMMC/SPI Connector
Micro-SD Slot
2x USB 3.0 Port
2x USB 2.0 Port
Headphone Jack
M.2 E-Key
USB PD/QC 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now we have rk3588 support :)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit f98f95359b.
It seems that this commit is causing issues with the PWM fan on the RPi 5 as
reported here: https://github.com/openwrt/openwrt/issues/16191
So let's revert this for now.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The D-Link DSL-2750B rev B1 (AW4339U) is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.
This ports the device from old target bcm63xx/generic to bmips/bcm6328.
The hardware is the same of D-Link DSL-2740B rev F1 and DSL-2741B rev F1, plus a usb2 port.
Hardware:
- SoC: Broadcom BCM63281
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB (Nanya NT5TU32M16DG)
- Flash: 8 MB NOR (Macronix MX25L6406ENI-12G)
- Ethernet LAN: 4x 100Mbit (Broadcom BCM63281)
- Wifi 2.4 GHz: 802.11bgn (Atheros AR9287)
- USB: 1x 2.0
- Buttons: 3x
- LEDs: 10x
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Samuele Longhi <agave@dracaena.it>
It's upstream and a replacement for the swconfig driver.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16124
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allows removing free_irq. Simpler.
Oddly enough the other switch code already does this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16050
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware:
- SoC: MediaTek MT7628DAN (MIPS 580MHz)
- Flash: 8 MiB Spansion S25FL064K
- RAM: 64 MiB (built-into SoC)
- WLAN: 2.4 GHz (MT7628)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- Buttons: 1 Reset button
- LEDs: 1x Red, 1x Green
- Serial console: unpopulated header, 57600 8n1 (RX only)
- Power: 12 VDC, 1 A
There are unpopulated areas on the board for 5 GHz WiFi via PCIe as well
as (most likely) Quectel EG25-G 4G module. As both are not populated on
my board support for both is missing for now.
Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.188.253/ and upload sysupgrade.bin file.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the KERNEL_BTRFS_FS config option so that targets can select
whether BTRFS support must be built-in.
Select this option (alongside KERNEL_BTRFS_FS_POSIX_ACL) from the
layerscape/armv8_64b subtarget instead of enabling it in
target/linux/layerscape/armv8_64b/config-* files.
Move disabling of CONFIG_BTRFS_FS_CHECK_INTEGRITY into generic configs.
This makes it possible for OpenWRT to be built with built-in BTRFS
support on specific boards, instead of whole targets.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/15990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
- MT7629 CPU
- MT7531 switch
- MT7761N and MT7762N wifi
- 256 MB RAM
- 128 MB NAND flash with dual-boot partitions
- 2 buttons: WPS and reset
- 1 WAN port (1G)
- 4 LAN ports (1G)
- 1 USB port
Limitations (same as other MT7629/MT7761N/MT7762N devices):
- Wifi is not working
- Second core is not working (kernel error message "CPU1: failed to come online")
Disassembly:
- There are two screws under the front rubber feet and two under the label on the bottom (in the corners towards the back, you should be able to feel them).
Serial Interface:
- UART pin header is already soldered on the board. Pinning from front to back:
1 - VCC
2 - TX
3 - RX
4 - n/a
5 - GND
GPIO:
- 1 white LED, connected to GPIO 52
- 1 reset button, connected to GPIO 60
- 1 WPS button, connected to GPIO 58
MAC Adresses:
- The MAC address printed on the device label is used for LAN and WAN
- The MAC address is stored in the devinfo partition in ASCII format (hw_mac_addr=aa:bb:cc:dd:ee)
- 2.4 GHz wifi uses MAC of the device label + 1
- 5 GHz wifi uses MAC of the device label + 2
Flashing:
- OpenWrt is only runnig in the first partition of dual boot
- To ensure to be able to go back to the factory image, flash the last OEM firmware via OEM web interface. This will ensure that the OEM firmware is present on both partitions
- Because of dual boot partitions, flashing via OEM interface is not supported
- Start a TFTP server and provide the initramfs image. Default settings:
- Router IP: 192.168.1.1
- TFTP server IP: 192.168.1.100
- TFTP file name: 7531.bin
- Open the device, connect UART and select " 1. System Load Linux to SDRAM via TFTP." during startup
- Adapt the settings to your environment, if required
- After initramfs is booted, flash the sysupgrade image
Return to OEM firmware:
- Run the following commands in OpenWrt to switch to the second partition
fw_setenv boot_part 2
fw_setenv bootimage 2
- Reboot the device. OEM firmware will start up again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16067
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SUPPORTED_DEVICES is required for Radxa ROCK Pi S.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the LED definitons for the XG6846 DSA port LEDs.
These are standard properties compatible with the existing
Marvell 88e6xxx DT bindings and fully standardized so this
is fine to add. They will be used by the in-flight Marvell
88e6xxx LEDs support patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[add empty lines between leds, remove default-state="off"]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
For some troublesome devices it is necessary to obtain direct access
to the SFP module EEPROM so define it in the device tree.
Suggested-by: Paul Donald <newtwen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some versions of the Inteno XG6846 has a USB port mounted.
For these machines the corresponing USB port nodes need to
be enabled.
Suggested-by: Henrik Ginstmark <henrik@ginstmark.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[reorder DTS alphabetically]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
997acc7f86 split this PHY driver up such
that external QCA switches now use CONFIG_QCA83XX_PHY. Fix it here so
that ethernet works again.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16154
Signed-off-by: Robert Marko <robimarko@gmail.com>
The second edition of international version of Mi Router 4A 100M is
very similar to the non-international one, but has another wireless chip.
Installation
--------------
1. Initialize build-in firmware (use webgui for 192.168.31.1)
You should install root password
2. Run OpenWRTInvasion for the first time (probably it will fail)
Version 0.0.10 is working as well as 0.0.1.
3. Run OpenWRTInvasion for the second time
It will create an access to your router
4. Upload sysupgrade image to router (/tmp/fw.bin)
pc# nc -l 8080 < …/ramips/mt76x8/…-100m-intl-v2-squashfs-sysupgrade.bin
router# nc 192.168.31.175 8080 > /tmp/fw.bin
5. Flash new firmware
router# run mtd -r write /tmp/fw.bin OS1
6. Check result
Wait about 5-10 minutes after flash. Router should reboot itself and
turn left led from orange to blue.
In case of failure one can use Xiaomi 4a 100m debrick tool
(it uploads special image via tftpd in recovery mode)
After that you can start again from step 1.
Another actions are very similar to original Mi Router 4A 100M
Original mtd paritions:
-------------------------
```
Creating 9 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000020000 : "Bootloader"
0x000000020000-0x000000030000 : "Config"
0x000000030000-0x000000040000 : "Factory"
0x000000040000-0x000000050000 : "crash"
0x000000050000-0x000000060000 : "cfg_bak"
0x000000060000-0x000000160000 : "overlay"
0x000000160000-0x000000dc0000 : "OS1"
0x000000dc0000-0x000001000000 : "disk"
with special sub-partition
0x0000002c0000-0x000000dc0000 : "rootfs"
```
We will use OS1+disk space:
```
0x000000160000-0x000001000000 : "firmware"
```
Co-authored-by: Nita Vesa <nita.vesa@elektrik.link>
Signed-off-by: Anton Stratonnikov <billic@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/14304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NVMEM is the upstream replacement for this. ralink,mtd-eeprom is
deprecated. The others need to stay as there's byte swapping going on.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16084
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also migrate mt7623 to new fitblk support scripts which simplify
sysupgrade when using uImage.FIT. This had been forgotten previously.
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Simplifies the code by removing clk_disable_unprepare.
Also removed gotos and used dev_err_probe.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16133
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a use-after-free bug in mtk_wed_setup_tc_block_cb()
which leads to kernel panic when setup multiple ap
interfaces on one band of mt798x.
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16118
Signed-off-by: Robert Marko <robimarko@gmail.com>
Read the 'fip' static volume in order to trigger scrubbing in case of
detecting flipped bits while reading.
We have to do this in Linux because we never read or touch the 'fip'
volume and the UBISPL implementation in ARM TrustedFirmware-A does NOT
handle scrubbing itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reporting an unclean read from SPI-NAND only when the maximum number
of correctable bitflip errors has been hit seems a bit late.
UBI LEB scrubbing, which depends on the lower MTD device reporting
correctable bitflips, then only kicks in when it's almost too late.
Set bitflip_threshold to 75% of the ECC strength, which is also the
default for raw NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It seems that some Xiaomi AX3000T boards changed to using Winbond W25N01KV
SPI-NAND which is not supported in OpenWrt nor upstream kernel.
So, add a pending patch to support it as upstream supports rest of the KV
revision models.
Fixes: #16002
Link: https://github.com/openwrt/openwrt/pull/16088
Signed-off-by: Robert Marko <robimarko@gmail.com>
We need to configure the led and network config for this board on
start as per the others
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches for the nanopi r6s board, backporting from 6.9 where
basic support is landing.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.
Hardware:
Model: Cambium Networks XE3-4
CPU: IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
Memory: 1 GiB
Flash: 512 MiB Macronix MX30UF2G18AC + W25Q128FW
Ethernet: 1x 1 GbE (QCA8072)
1x 2.5 GbE (QCA8081)
Buttons: 1x Reset
Serial: TX, RX, GND
Baudrate: 115200
Radios: Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
BLE 4.1
Power: 32.0W 802.3bt5 PoE++
25.5W 802.3at with USB, BT disabled
Size: 215mm x 215mm
Ports: 1x USB 2.0
Antenna: 6 GHz: 6.29 dBi, Omni 30 dBm
5 GHz: 6.12 dBi, Omni 31 dBm
2.4 GHz: 4.85 dBi, Omni 29 dBm
LEDs: Multi-color status LEDs
Mounting: Wall, ceiling or T-bar
Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
one of the APs GND pins.
3. Transfer the initramfs image with TFTP
(Default server IP is 192.168.0.120)
# tftpboot factory.ubi
4. Flash the rootfs partition
# flash rootfs
5. Reboot the AP
# reset
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15633
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes the image check failed on system upgrade
"Image check failed:
upgrade: Device radxa,rock3a not supported by this image
upgrade: Supported devices: radxa,rock-3a"
Signed-off-by: Tomas Lara <tl849670@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to RTL8221B's datasheet, the PHY requires at least 10ms
for assert and 68ms (recommended) for de-assert. So increase the
assert/de-assert time to 15ms and 68ms respectively.
Fixes: c0c3234e17 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16106
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refactor Inteno XG6846 device tree to be in line with other bmips devices.
Also expose USB LED automatically.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Enable CONFIG_HWMON and CONFIG_THERMAL_HWMON on all subtargets.
- Drop kmod-thermal from bcm2712.
- Add CONFIG_SENSORS_RASPBERRYPI_HWMON generic symbol.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
target/linux/archs38/image/Makefile calls gen_axs10x_sdcard_img.sh
with $(CONFIG_TARGET_ROOTFS_PARTSIZE).
Make sure a rootfs partition is built and usable.
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Link: https://github.com/openwrt/openwrt/pull/16098
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ec885796c0 switched the crc32 implementation from default to
byte-at-a-time algorithm, which runs slower but consumes less memory.
A decade has passed, and we have already abandoned targets that had
small memory, so switch it back to default for faster speed.
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Enable the CONFIG_MTD_SPI_NOR_USE_VARIABLE_ERASE kernel option to allow for
U-Boot environment writing. This might be hiding a problem somewhere else,
since the w25q128fw chip supports 32K erases, still this change makes it
much easier to switch the GL-MV1000 boot media without an UART cable
connection.
Thanks to @robimarko and @hacks for the precious hints and suggesting a
better approach.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
This allows booting from internal eMMC or SD card just changing the
U-Boot mmc_dev variable.
In particular, setting mmc_dev to 1 will result in booting from the SD card.
Setting the variable to 0 will result in internal eMMC boot (the default).
Should the variable be unset or an error condition occur while reading
from SD card, internal MMC booting will be tried.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
mpc85xx was switched to 6.6. We can remove 6.1 support now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16087
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's time for wide tests.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16087
Signed-off-by: Robert Marko <robimarko@gmail.com>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.44..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds auto-configuration of network ports on Dell EMC Edge620 (x86) product.
It is similar in specs/features to some of the Sophos x86-based appliances, but:
1. Serial console terminal is built in and requires just the micro-USB cable
2. Comes with both MMC (16Gb) and SSD (256Gb) installed
3. Comes with 6 ethernet ports all 6 are functional when no SFP is used
4. Comes with two SFP cages and not one, like some of revision 3 Sophos products
5. Unlike Sophos devices, there are no non-wireless models of Edge 620,
it comes with Qualcomm Atheros QCA9880 radio
These devices can be now found both second-hand and new at online marketplaces below
(sometimes well below) US $100, I believe they make great candidates for running OpenWrt.
The ethernet network ports on the case are marked GE1 thru to GE6 with the
following mapping once booted into OpenWrt:
```
GE1: eth2: pci0000:00/0000:00:0b.0/0000:02:00.2
GE2: eth3: pci0000:00/0000:00:0b.0/0000:02:00.3
GE3: eth0: pci0000:00/0000:00:0b.0/0000:02:00.0
GE4: eth1: pci0000:00/0000:00:0b.0/0000:02:00.1
GE5: eth7: pci0000:00/0000:00:17.0/0000:07:00.1
GE6: eth6: pci0000:00/0000:00:17.0/0000:07:00.0
```
Dell's instructions for [standard configuration](https://infohub.delltechnologies.com/en-us/l/dell-emc-edge-620-advanced-activation-guide/dell-emc-sd-wan-edge-620-standard-configuration/)
recommend using GE3, GE4, GE5, or GE6 for WAN, I've selected the GE6 as the sole
WAN port under OpenWrt with the rest of ethernet ports assigned to LAN.
Please merge before 24.xx is forked and if possible, cherry-pick for 23.05
if there's no ETA for 24.xx forking.
PS. @Hurricos I'm struggling with ixgbe mappings on Sophos devices which use
very similar hardware to Dell EMC, so even tho I know the sys paths for ethernet ports,
I'd prefer to do a separate commit to properly map ethernet ports to match the case markings
for this device at some point later.
Signed-off-by: Stan Grishin <stangri@melmac.ca>
Use realtek,extif property instead of realtek,extif0 to extif2
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Store the chip type in smi->rtl8367b_chip
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove the rlvid analysis because for the rtl8367b family chips supported
by the driver (rtl8367rb and rtl8367r-vb), rlvid is always equal to 1.
So the code for rlvid equal to 0 is completely unnecessary.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use realtek,extif property instead of realtek,extif0 and realtek,extif1
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop config for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16030
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16030
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new utility, omnia-mcutool, which main purpose is to upgrade the
firmware on the microcontroller on the Turris Omnia router. Depends on
omnia-mcu-firmware, and the upgrade process is pretty simple:
omnia-mcutool --upgrade
Besides firmware upgrade, the utility can be used to show and configure
various firmware settings.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new package, omnia-mcu-firmware, containing firmware binaries for
the microcontroller on the Turris Omnia router.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the MCU driver on CZ.NIC's Turris Omnia. This adds
the ability to do a true board poweroff, and to configure various
features (for example the user may configure that after poweroff, the
router should automatically wake up at a specific time).
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
This backports patches
dt-bindings: firmware: add cznic,turris-omnia-mcu binding
platform: cznic: Add preliminary support for Turris Omnia MCU
platform: cznic: turris-omnia-mcu: Add support for MCU connected GPIOs
platform: cznic: turris-omnia-mcu: Add support for poweroff and wakeup
platform: cznic: turris-omnia-mcu: Add support for MCU watchdog
platform: cznic: turris-omnia-mcu: Add support for MCU provided TRNG
ARM: dts: turris-omnia: Add MCU system-controller node
ARM: dts: turris-omnia: Add GPIO key node for front button
platform: cznic: turris-omnia-mcu: Depend on OF
platform: cznic: turris-omnia-mcu: Depend on WATCHDOG
platform: cznic: turris-omnia-mcu: fix Kconfig dependencies
that will be released in 6.11 into mvebu/patches-6.6.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
This target doesn't actually use NAND.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16001
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit f444dea428.
It seems that some devices using GPIO WDT have really short WDT timeouts
and when using module_platform_driver registration it happens too late
and thus WDT will timeout and reset the board.
So, for now lets return the postcore_initcall hack for now.
Fixes: f444dea428 ("ath79: remove GPIO driver earlier registration hack")
Signed-off-by: Joan Moreau <jom@grosjo.net>
Link: https://github.com/openwrt/openwrt/pull/16035
Signed-off-by: Robert Marko <robimarko@gmail.com>
Layerscape was switched to 6.6 kernel. Now is time to remove 6.1
support.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16037
Signed-off-by: Robert Marko <robimarko@gmail.com>
CI says patches need to be refreshed, so do so.
Fixes: 6bb334c5cf ("mediatek: fix u-boot env layout NVMEM definitions")
Link: https://github.com/openwrt/openwrt/pull/16051
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kirkwood was switched to 6.6. We can remove 6.1 support now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
generic.mk was commited by mistake. It isn't used. Let's remove it.
Fixes: ccbdb212f3 ("kirkwood: Add missing package dependency")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
Let's switch to kernel 6.6 for wide tests.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
Radxa ROCK Pi E v3.0 has a RTL8723DU Wi-Fi 4 on-board device. enable
it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S has a RTL8723DS Wi-Fi 4 on-board device. enable it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Import patch from mainline Linux to fix issue with PERST# signal
polarity.
Quote from commit message:
"This extra, very short, PERST# assertion + deassertion has been
reported to cause issues with certain WLAN controllers, e.g. RTL8822CE."
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Testing turned out that the HWRNG quality varies greatly on RK3566,
even on supposedly identical boards and SoC revisions.
Hence enable the HWRNG driver only on RK3568 for now.
Allow users to simply tune sample_count and quality to allow easily
testing results on different boards and SoCs.
Link: https://patchwork.kernel.org/project/linux-arm-kernel/cover/cover.1720969799.git.daniel@makrotopia.org/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a backport of netdev/net [1]/[2], expected to be in kernel 6.11
(if not backported to a stable branch).
Since 4fdc7bb8f1 (2024-06-14, switching ath79 from kernel 6.1 to 6.6),
the rtl8366s driver was made to write to bogus PHY MII registers on
ath79/netgear,wndr3800 and family, and likely on other systems using
this switch in a similar manner. The writes were directed to PHY 4 MII
registers 0x0d (13) and 0x0e (14). The rtl8366s data sheet claims these
registers are reserved. These register writes were causing the device to
not maintain link, track link status, or pass traffic on eth1 (labeled
WAN), as eth1 is connected to PHY 4.
0x0d is MII_MMD_CTRL, and 0x0e is MII_MMD_DATA. rtl8366s doesn't appear
to support MMD in any way, and certainly not via the IEEE 802.3 annex
22D "clause 45 over clause 22" protocol implemented by mmd_phy_indirect.
This patch intercepts those attempted register accesses and returns
-EOPNOTSUPP without touching the switch chip. This is implemented by
defining phy_driver::{read,write}_mmd as
genphy_{read,write}_mmd_unsupported for this PHY. A new PHY driver for
this PHY is introduced to achieve that, because this PHY was previously
using genphy_driver, and there is otherwise no clean way to declare lack
of support for these operations.
This was caused by kernel 9b01c885be36 (2023-02-13, in 6.3). The new
genphy_c45_read_eee_abilities call in genphy_read_abilities (called
during phy_probe) was causing an attempted MMD read of (MMIO_MMD_PCS,
MDIO_PCS_EEE_ABLE), which was transformed into an annex 22D
mmd_phy_indirect operation that performed MII register writes to
MII_MMD_CTRL, MII_MMD_DATA, and MII_MMD_CTRL again, followed by another
read from MII_MMD_DATA. This was enough to "scramble" the state of those
two MII registers, which are in fact not used for annex 22D MMD register
access on this device but are reserved and have some other function,
rendering the PHY unusable while so configured. The result of the
bungled MMD read attempt caused the genphy driver to incorrectly believe
that the PHY supported standard EEE, which led to several more attempted
MMD writes and reads, in turn being transformed into writes to these two
MII registers.
rtl8366s does support some pre-IEEE 802.3az EEE standard form of "Green
Ethernet" which the switch driver (local to OpenWrt) already has some
support for. No attempt is made to map the standard operations for this
device.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=225990c487c1
[2] https://lore.kernel.org/netdev/20240725204147.69730-1-mark@mentovai.com/
Fixes: https://github.com/openwrt/openwrt/issues/15981
Link: https://github.com/openwrt/openwrt/issues/15739
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16012
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi E v3.0 is a compact networking SBC[1] using the Rockchip
RK3328 SoC.
Hardware
--------
- Rockchip RK3328 SoC
- Quad A53 CPU
- 512MB/1GB/2GB DDR4 RAM
- 4/8/16/32GB eMMC
- Micro SD Card slot
- WiFi 4 and BT 4, or WiFi 5 and BT 5 (not supported yet)
- 1x 1000M Ethernet with PoE support (additional PoE HAT required)
- 1x 100M Ethernet
- 1x USB 3.0 Type-A port (Host)
- 1x 4-ring 3.5mm headphone jack
- 40 Pin GPIO header
[1] https://radxa.com/products/rockpi/pie
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15984
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
The hardware of these two models looks the same. This patch also
disabled unused i2c bus for WE3526.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
From the kernel log, we are using PCIe port 1 and 2.
dmesg:
```
[ 0.963526] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[ 0.970432] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 0.975312] mt7621-pci 1e140000.pcie: PCIE2 enabled
[ 1.071442] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 1.130382] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
```
Fixes: https://github.com/openwrt/openwrt/issues/16000
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for a dual-band AX1800 wall plug manufactured
by Shenzhen Century Xinyang Tech Co., Ltd.
CPU: Mediatek MT7621A (2 cores, 4 threads)
RAM: 256i MiB DDR3 (Samsung K4B2G1646F-BCNB)
ROM: 16 MiB SPI NOR (Winbond W25Q128JVPQ)
Wired: one gigabit RJ45 port (with green/yellow non-GPIO LEDs)
WiFi: Mediatek MT7905DAN + MT7975DN (DBDC 2x 2T2R)
Ant.: four 2 dBi external antennas (two 2.4GHz, two 5 GHz)
GPIO: tri-color status LED (GPIO 13, 14, 16);
reset button (GPIO 18)
Power: 12V 2-pin JST-XH on main PCB
110/220V AC to 12V1A DC on auxiliary PCB
UART: 115200 8n1, SMD pads available on the PCB as J4
pinout is [3v3] (Rx) (Tx) (Gnd)
MAC: 1C:BF:CE:xx:xx:xx (2.4 GHz, label)
1C:BF:CE:xx:xx:xx + 1 (ethernet [1])
1C:BF:CE:xx:xx:xx + 2 (5 GHz)
Original firmware is LEDE Reboot 17.01-SNAPSHOT (kernel 4.4.198)
with a few custom packages and a non-LuCI web interface.
Telnet and SSH are enabled, requiring an unknown root password [2].
Root password is also needed to access the router via UART console,
but passwordless telnet can be enabled via a trivial web exploit [3]
and then the root password can be removed by editing `/etc/shadow`.
Installation: First upload `sysupgrade` binary via web interface at
`http://192.168.188.1/settings.shtml` and wait until getting back to
the home screen (select network to extend). The installation fails
since the original firmware uses `swconfig` and recent versions of
OpenWrt use DSA. However, the sysupgrade file is uploaded correctly
and stored at `/tmp/upgrade.bin`, so it can be written to flash via
the web exploit [4] (both `mtd -r write` and `sysupgrade -Fn` work
fine). Passwordless telnet/ssh is not needed for installation.
Alternatively, use u-boot menu to load image via TFTP.
Notes:
- Device model in LEDE is "MediaTek MT7621 RFB (802.11ax,SNOR)".
- It is sold under several names, among them are Wodesys WD-R1802U,
Fenvi F-AX1802U, and EDUP EP-2971; the Wodesys brand was selected
since it is referenced in `/etc/banner` and `/etc/hosts`, and the
PCB is marked "WD518A V1.0".
- Instead of a standard ethernet transformer, the PCB has a few tiny
SMD coils.
[1] Original firmware sets ethernet MAC to 1C:BF:CE:E7:62:1D based on
offset `0x3fff4` in the Factory partition; since this is the same
MAC for all units, whereas WiFi MACs stored at offsets 0x6 and 0xc
are unique, it was decided to use <label MAC + 1> for ethernet.
[2] root:$1$7rmMiPJj$91iv9LWhfkZE/t7aCBdo.0:18388:0:99999:7:::
[3] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;killall telnetd;telnetd -l /bin/sh"
[4] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;mtd -r write /tmp/upgrade.bin firmware"
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15777
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport H616 DVFS support from linux-next.
Tested on the Orange Pi Zero 3 (H618 SoC).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15600
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Freescale procesor has Securite Engine driver called Talitos. [1]
This driver is already packaged for OpenWrt since commit
bf57f33f02 ("kernel: Allow talitos crypto
hw module selection"), but many users don't know about it.
Let's include this kernel module package to default packages as it was
recently done for MediaTek in commit 06c4fc6d5e
("kernel: enable inside secure driver for MediaTek platforms")
[1] https://cateee.net/lkddb/web-lkddb/CRYPTO_DEV_TALITOS.html
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/10557
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some devices lock up on PCIe initialization:
[ 64.309697] PCIe: Port 0 in endpoint mode, skipping.
[ 64.320496] PCIe: Initializing port 1
[ 64.325257] PCIe: BIST FAILED for port 1 (0xffffffffffffffff)
(system hangs here)
Given the ER contains no PCIe peripherals, has no way to attach any
and the stock kernel doesn't have PCIe support either, just disable it.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/15992
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16021
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16021
Signed-off-by: Robert Marko <robimarko@gmail.com>
NEC Aterm WG600HP is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG600HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG600HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : A4:12:42:xx:xx:A0 (config, 0x6 (hex))
WAN : A4:12:42:xx:xx:A1 (config, 0xc (hex))
2.4 GHz: A4:12:42:xx:xx:A2 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : A4:12:42:xx:xx:A3 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WR9500N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, Atheros AR9344 (SoC)
- 5 GHz : 3T3R, Atheros AR9380
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 12x/4x
- note : all LEDs are controlled by ath9k chip (AR9380)
- UART : pad on PCB (near shielded ath9k chip, white circle)
- assignment : 3.3V, GND, TX, RX from AR8327 side
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR9500N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR9500N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9380) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:60 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:61 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:62 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:63 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WR8750N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR8750N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR8750N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:00 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:01 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:02 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:03 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix PCIe initialization on AR934x by clearing PLL_PWD bit in addition to
PPL(PLL?)_RESET bit of AR724x.
Refresh patches by `make target/linux/refresh`.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The archs38 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix uninitialized variable warnings in function regcache_maple_drop
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel config for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT40A512M16TB-062ER 1GB
Ethernet: 2x 2.5G, 4x 1G Lan
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5.2GHz 4T4R
WiFi3: MT7915AN 5.8GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 5A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).
Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)
Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.
Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Radxa ROCK Pi S is a small in size, full in features SBC[1] using the
Rockchip RK3308B SoC.
Hardware
--------
- Rockchip RK3308B SoC
- Quad A35 CPU
- 256/512MB DDR3 RAM
- Optional 4/8GB eMMC
- Micro SD Card slot
- Optional WiFi 4 and BT 4 (not supported yet)
- 1x 100M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 2.0 Type-A port (Host)
- 1x USB 2.0 Type-C port (OTG)
- 2x 26 Pin GPIO header
[1] https://radxa.com/products/rockpi/pis
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Keenetic KN-3510 is a 2.4/5 Ghz band 11ax access point
Specification:
- System-On-Chip: MT7621AT
- CPU/Speed: 880 MHz
- Flash-Chip: Macronix MX30LF1G28AD-TI
- Flash size: 128 MiB
- RAM: 256 MiB
- 2x 10/100/1000 Mbps Ethernet
- PoE, 802.3af/at
- 4x internal antennas
- UART (J1) header on PCB (115200 8n1)
- WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps
- 2x LED, 2x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3510-squashfs-factory.bin"
to "KN-3510_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is exactly the same as WL-WN531G3 but with different partition layout and different MAC layout. Labeled as Quantum D4G Rev.: A2.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x Touchlink button
- 1x Turbo button
- 1x Wps button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 5x Blue leds (ethernet ports)
- 1x Power led
- 1x Wifi led
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:0F (factory @ 0x28)
WAN XX:XX:XX:XX:XX:10 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:11 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:12 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:11
Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15876
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In make menuconfig the name is [Amplifi Router HD], and
is missing Ubiquiti. Lets fix that by adding
DEVICE_VENDOR := Ubiquiti to generic-ubnt.mk so the name is:
[Ubiquiti Amplifi Router HD].
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15932
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.
Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- radio0 (Wi-Fi 2.4GHz) = label MAC + 1
- radio1 (Wi-Fi 5GHz) = label MAC + 2
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP6X10XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap6010dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/15941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove kmod-switch-rtl8366-smi from the package list, as it is still loaded
because kmod-switch-rtl8367b depends on it
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15757
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit fixes all errors reported by the checkpatch script. This
should make it easier to accept upstream this patch.
There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes two issues in the driver detach:
* double free of the same descriptor (upstream bug, backported in 66177c081f),
* releasing tx descriptor instead of rx (downstream bug).
The driver is compiled into the kernel that is why the error
is not visible in normal use.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Switch to new nvmem binding.
Also fixes a issue that the MAC address assigned to lan/wan was
reversed on eMMC boards.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Also use env variables exported by export_fitblk_rootdev() in
platform_copy_config().
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The target was marked source-only due do the broken Ethernet port on
some devices. With that fixed, it can be enabled again.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The new cpsw-switch driver reserves VLAN 1 for internal use, which
conflicts with the default network configuration of OpenWrt.
Switch back to the older cpsw driver to make the network connection on
the affected devices (BeagleBone Black and AM335x EVM) usable again.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Initramfs images are not supported by imagebuilder. With recent changes
to support Per Device Rootfs, we now generate an image and a vmlinux for
each Rootfs and these additional files are all shipped in the
imagebuilder tar.
Drop these new file and any vmlinux-initramfs as they are not used and
increase the final size of the imagebuilder archive.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The eMMC chip used in a small batch of these devices has issues operating
in HS400 mode. Reducing to HS200 mode works around the problem and does
not cause any noticeable performance penalties as smaller chips are not fast
enough to saturate the bus. Root cause analysis is pending.
Signed-off-by: Chad Monroe <chad@monroe.io>
