mirror of
https://github.com/openwrt/openwrt.git
synced 2025-02-20 01:16:23 +00:00
bmips: bcm6328: add support for D-Link DSL-2750B rev B1
The D-Link DSL-2750B rev B1 (AW4339U) is a wifi fast ethernet router, 2.4 GHz single band with two external antennas. This ports the device from old target bcm63xx/generic to bmips/bcm6328. The hardware is the same of D-Link DSL-2740B rev F1 and DSL-2741B rev F1, plus a usb2 port. Hardware: - SoC: Broadcom BCM63281 - CPU: single core BMIPS4350 @ 320Mhz - RAM: 64 MB (Nanya NT5TU32M16DG) - Flash: 8 MB NOR (Macronix MX25L6406ENI-12G) - Ethernet LAN: 4x 100Mbit (Broadcom BCM63281) - Wifi 2.4 GHz: 802.11bgn (Atheros AR9287) - USB: 1x 2.0 - Buttons: 3x - LEDs: 10x - UART: yes Installation via CFE web UI: 1. Power off the router. 2. Press reset button near the power switch. 3. Keep it pressed while powering up during ~20+ seconds. 4. Browse to http://192.168.1.1 and upload the firmware. 5. Wait a few minutes for it to finish. Signed-off-by: Samuele Longhi <agave@dracaena.it>
This commit is contained in:
Samuele Longhi
Álvaro Fernández Rojas
parent
b75a7ca0bc
commit
ba9c269e1e
@ -14,6 +14,7 @@ inteno,xg6846)
|
||||
;;
|
||||
comtrend,ar-5381u |\
|
||||
comtrend,ar-5387un |\
|
||||
dlink,dsl-2750b-b1 |\
|
||||
innacomm,w3400v6 |\
|
||||
nucom,r5010unv2)
|
||||
ucidef_set_bridge_device switch
|
||||
|
||||
@ -6,6 +6,7 @@ case "$(board_name)" in
|
||||
arcadyan,ar7516 |\
|
||||
comtrend,ar-5381u |\
|
||||
comtrend,ar-5387un |\
|
||||
dlink,dsl-2750b-b1 |\
|
||||
nucom,r5010unv2)
|
||||
mtd fixtrx firmware
|
||||
;;
|
||||
|
||||
273
target/linux/bmips/dts/bcm6328-dlink-dsl-2750b-b1.dts
Normal file
273
target/linux/bmips/dts/bcm6328-dlink-dsl-2750b-b1.dts
Normal file
@ -0,0 +1,273 @@
|
||||
#include "bcm6328.dtsi"
|
||||
|
||||
/ {
|
||||
model = "D-Link DSL-2750B rev B1/DSL-2740B rev F1/DSL-2741B rev F1";
|
||||
compatible = "dlink,dsl-2750b-b1", "brcm,bcm6328";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <100>;
|
||||
|
||||
wifi {
|
||||
label = "wifi";
|
||||
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WLAN>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-31 {
|
||||
function = LED_FUNCTION_USB;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&ehci_port1>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
};
|
||||
|
||||
ath9k-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-8 {
|
||||
function = LED_FUNCTION_WLAN;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&ath9k 8 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&leds {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_leds>;
|
||||
|
||||
led@2 {
|
||||
reg = <2>;
|
||||
active-low;
|
||||
label = "red:internet";
|
||||
};
|
||||
|
||||
led@3 {
|
||||
reg = <3>;
|
||||
active-low;
|
||||
label = "green:dsl";
|
||||
};
|
||||
|
||||
led_power_green: led@4 {
|
||||
reg = <4>;
|
||||
active-low;
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led_power_red: led@8 {
|
||||
reg = <8>;
|
||||
active-low;
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led@9 {
|
||||
reg = <9>;
|
||||
active-low;
|
||||
function = LED_FUNCTION_WPS;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
};
|
||||
|
||||
led@11 {
|
||||
reg = <11>;
|
||||
active-low;
|
||||
label = "green:internet";
|
||||
};
|
||||
};
|
||||
|
||||
&ehci {
|
||||
status = "okay";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ehci_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&macaddr_cfe_6a0 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&hsspi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <16666667>;
|
||||
spi-tx-bus-width = <2>;
|
||||
spi-rx-bus-width = <2>;
|
||||
reg = <0>;
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
reg = <0x000000 0x010000>;
|
||||
label = "cfe";
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_cfe_6a0: macaddr@6a0 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x6a0 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@10000 {
|
||||
reg = <0x010000 0x7c0000>;
|
||||
label = "linux";
|
||||
compatible = "brcm,bcm963xx-imagetag";
|
||||
};
|
||||
|
||||
partition@7d0000 {
|
||||
reg = <0x7d0000 0x010000>;
|
||||
label = "cal_data";
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
cal_data_1000: calibration@1000 {
|
||||
reg = <0x1000 0x440>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@7e0000 {
|
||||
reg = <0x7e0000 0x020000>;
|
||||
label = "nvram";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ohci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
pcie@0 {
|
||||
reg = <0 0 0 0 0>;
|
||||
#interrupt-cells = <1>;
|
||||
#size-cells = <2>;
|
||||
#address-cells = <3>;
|
||||
device_type = "pci";
|
||||
|
||||
ath9k: wifi@168c,002e {
|
||||
compatible = "pci168c,002e";
|
||||
reg = <0 0 0 0 0>;
|
||||
|
||||
nvmem-cells = <&macaddr_cfe_6a0 1>, <&cal_data_1000>;
|
||||
nvmem-cell-names = "mac-address", "calibration";
|
||||
|
||||
#gpio-cells = <2>;
|
||||
gpio-controller;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
pinctrl_leds: leds {
|
||||
function = "led";
|
||||
pins = "gpio2", "gpio3", "gpio4",
|
||||
"gpio8", "gpio9", "gpio11";
|
||||
};
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "lan1";
|
||||
|
||||
phy-handle = <&phy1>;
|
||||
phy-mode = "mii";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
|
||||
phy-handle = <&phy2>;
|
||||
phy-mode = "mii";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
|
||||
phy-handle = <&phy3>;
|
||||
phy-mode = "mii";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan4";
|
||||
|
||||
phy-handle = <&phy4>;
|
||||
phy-mode = "mii";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh {
|
||||
status = "okay";
|
||||
};
|
||||
@ -39,6 +39,27 @@ define Device/comtrend_ar-5387un
|
||||
endef
|
||||
TARGET_DEVICES += comtrend_ar-5387un
|
||||
|
||||
define Device/dlink_dsl-2750b-b1
|
||||
$(Device/bcm63xx-cfe)
|
||||
DEVICE_VENDOR := D-Link
|
||||
DEVICE_MODEL := DSL-2750B
|
||||
DEVICE_VARIANT := B1
|
||||
DEVICE_ALT0_VENDOR := D-Link
|
||||
DEVICE_ALT0_MODEL := DSL-2740B
|
||||
DEVICE_ALT0_VARIANT := F1
|
||||
DEVICE_ALT1_VENDOR := D-Link
|
||||
DEVICE_ALT1_MODEL := DSL-2741B
|
||||
DEVICE_ALT1_VARIANT := F1
|
||||
CFE_BOARD_ID := AW4339U
|
||||
CHIP_ID := 6328
|
||||
IMAGES := cfe-EU.bin cfe-AU.bin
|
||||
IMAGE/cfe-AU.bin := cfe-bin --signature2 "4.06.01.AUF1" --pad 4
|
||||
IMAGE/cfe-EU.bin := cfe-bin --signature2 "4.06.01.EUF1" --pad 4
|
||||
DEVICE_PACKAGES += $(USB2_PACKAGES) $(ATH9K_PACKAGES) \
|
||||
kmod-leds-gpio kmod-leds-bcm6328
|
||||
endef
|
||||
TARGET_DEVICES += dlink_dsl-2750b-b1
|
||||
|
||||
define Device/innacomm_w3400v6
|
||||
$(Device/bcm63xx-cfe)
|
||||
DEVICE_VENDOR := Innacomm
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user