eee02ccca8c8 device: add support to configure eee
bb28f6a291d9 wireless: fix sign comparison warning
35facc8306f5 wireless: fix premature removal of hotplug devices due to down state
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add additional uci-defaults function for configuring GRO settings and
conduit for network devices.
Tweaking the GRO values might increase performance on some low spec
device that lack some offload feature on gmac.
Tweaking conduit interface is specific to DSA based devices and is
useful for multi-CPU scenario where one CPU is dedicated to one single
port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Generalize ucidef_set_network_device functions to use a more generic
_ucidef_set_network_device_common that takes as args the option and the
value to apply instead of hardcoding.
This is to reduce duplicated code in preparation for addition of
additional option for board.d usage.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
841b05fbb91e system-linux: fix compilation error if IFLA_DSA_MASTER is not supported
5c9ecc1ff74f system-linux: make system_if_get_master_ifindex static
2dc7f450f3a2 system-linux: add option to configure DSA conduit device
838f815db5ef system-linux: add support for configurable GRO option
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update the devel/gdb package to version 13.2
* Remove the upstreamed patch 001-Add-support-for-readline-8.2.patch
* Adjust 130-gdb-ctrl-c.patch to upstream changes
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Currently for 802.1s only, for wifi 2.4GHz in g/n mode, 40MHz is never
permitted.
This is probably due to the complexity of setting periodic check for the
intolerant bit. When noscan option is set, we ignore the presence of the
intoleran bit in near AP, so we can enable 40MHz and ignore any complex
logic for checking.
Fixes: #13112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Also channel 7 for 2.4GHz can be set to HT40PLUS. Permit this and add it
to the list of the channels.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
noscan option for mesh was broken and actually never applied.
This is caused by a typo where ssid->noscan value is check instead of
conf->noscan resulting in the logic swapped and broken.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
noscan option was changed to hostapd_noscan but the entry in
wpa_supplicant was never updated resulting in the noscan option actually
never set.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update SSDK version to 12.4, this fixes weird SFP port link up/downs
while there is no SFP module plugged in.
Signed-off-by: Robert Marko <robimarko@gmail.com>
0352a33 uloop: support new interval and signal APIs
1468cc4 syntax: don't treat `as` and `from` as reserved keywords
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
3a07943 block: support skipping uuid check
56a9b4e block: consider currently mounted root device first
9cd09d4 block: try to find the root device on both / and /rom
c1a8d95 block: support extroot on already mounted overlay
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Store the private key with read and write permission for the user only
and not with read permissions for everyone. This converts the
write_file() function from fopen() to open() because open allows to
specify the permission mask of the newly created file. It also adds and
fixes some existing error handling.
OpenSSL does this in the same way already.
With this change it looks like this:
root@OpenWrt:/# ls -al /etc/uhttpd.*
-rw-r--r-- 1 root root 749 Nov 6 23:14 /etc/uhttpd.crt
-rw------- 1 root root 121 Nov 6 23:14 /etc/uhttpd.key
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Store the private key with read and write permission for the user only
and not with read permissions for everyone. This converts the
write_file() function from fopen() to open() because open allows to
specify the permission mask of the newly created file. It also adds and
fixes some existing error handling.
OpenSSL does this in the same way already.
With this change it looks like this:
root@OpenWrt:/# ls -al /etc/uhttpd.crt /etc/uhttpd.key
-rw-r--r-- 1 root root 519 Nov 6 22:58 /etc/uhttpd.crt
-rw------- 1 root root 121 Nov 6 22:58 /etc/uhttpd.key
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
383753dd65ae device/bridge: support passing extra vlans in the device_set_state call
b6e75eafc1af device: send notifications for device events via ubus
cab415c7aefd bridge: add auth-required bridge members with auth_status=0 if vlan is enabled
827a02f0343c bridge: add support for configuring vlans for auth=1,auth_status=false
40ed7363caf2 device: fix build error on 32 bit systems
516ab774cc16 system-linux: fix race condition on bringing up wireless devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the download of the kernel 5.15 for the bpf-headers when
kernel 6.1 is build for the target.
Even if kernel 6.1 was selected for the target we still use kernel 5.15
for the bpf-headers. The download script tried to download the 5.15
kernel from the 6.x directory on kernel,org and this failed. Define
PKG_SOURCE_URL based on PKG_PATCHVER and not KERNEL_BASE like done in
kernel.mk.
Without this change it tries to download the kernel from this URL:
ttps://cdn.kernel.org/pub/linux/kernel/v6.x/linux-5.15.129.tar.xz
Fixes: #13190Fixes: #13671Fixes: #13814
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Activate the secp521r1 ecliptic curve by default. This curve is allowed
by the CA/Browser forum, see
https://cabforum.org/wp-content/uploads/CA-Browser-Forum-BR-v2.0.1-redlined.pdf#page=110
This increases the size of libmbedtls12_2.28.5-1_aarch64_generic.ipk by
about 400 bytes:
Without:
252,696 libmbedtls12_2.28.5-1_aarch64_generic.ipk
With:
253,088 libmbedtls12_2.28.5-2_aarch64_generic.ipk
Fixes: #13774
Acked-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4101dd4 fw4: perform strict validation of zone and set names
a923c88 fw4: pass zone to templates whenever possible
597dc90 fw4: add support for zone log_limit
1874050 fw4: add log_limit to rules and redirects
19a8caf ruleset: dispatch ct states using verdict map
a5553da ruleset: reduce ksoftirqd load by refering to looopback by numeric id
de3483c tests: adjust zone log limit testcases
7392792 ruleset: do not emit redundant drop invalid rules
698a533 ruleset: apply egress MSS fixup later to apply final MTU before wire
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ath10k-ct based on kernel 6.4 doesn't have a fix present in previous
kernel. Add patch that port the compilation error fix from previous
kernel in the new 6.4 kernel.
Fixes: 7d3651f1b9 ("ath10k-ct: switch to 6.4")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch to the latest version so we match as close as possible to
our own mac80211 version.
Run-time tested on hundreds of devices in the field for months now:
- qca988x (wave 1)
- qca4019 (wave 2)
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
It's already pulled in from /etc/rc.common.
Fixes: #13758
Fixes: 6b23836071 ("package: avoid the use of eval to parse ipcalc.sh output")
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This reverts commit 3cc57ba462 as it
should be fixed in commit 78cbd5a57e11 ("tools: macOS: types.h: fix
missing unsigned types").
References: #13833
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 997ff740dc.
78cbd5apick as it should be fixed in commit 78cbd5a57e11 ("tools: macOS:
types.h: fix missing unsigned types").
References: #13833
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Upgrading wpa_supplicant from 2.9 to 2.10 breaks broadcom-wl/ath11k
based adapters. The reason for it is hostapd tries to install additional
IEs for scanning while the driver does not support this.
The kernel indicates the maximum number of bytes for additional scan IEs
using the NL80211_ATTR_MAX_SCAN_IE_LEN attribute. Save this value and
only add additional scan IEs in case the driver can accommodate these
additional IEs.
Bug: http://lists.infradead.org/pipermail/hostap/2022-January/040178.html
Bug-Debian: https://bugs.debian.org/1004524
Bug-ArchLinux: https://bugs.archlinux.org/task/73495
Upstream-Status: Changes Requested [https://patchwork.ozlabs.org/project/hostap/patch/20220130192200.10883-1-mail@david-bauer.net]
Reported-by: Étienne Morice <neon.emorice@mail.com>
Tested-by: Étienne Morice <neon.emorice@mail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CycloneDX is an open source standard developed by the OWASP foundation.
It supports a wide range of development ecosystems, a comprehensive set
of use cases, and focuses on automation, ease of adoption, and
progressive enhancement of SBOMs (Software Bill Of Materials) throughout
build pipelines.
So lets add support for CycloneDX SBOM for packages and images
manifests.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It must read the entire image for previous code of 'imsz' or 'imszb'.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Suggested-by: Chuanhong Guo <gch981213@gmail.com>
The code for hostapd-mbedtls did not work when used for OWE association.
When handling association requests, the buffer offsets and length
assumptions were incorrect, leading to never calculating the y point,
thus denying association.
Also when crafting the association response, the buffer contained the
trailing key-type.
Fix up both issues to adhere to the specification and make
hostapd-mbedtls work with the OWE security type.
Signed-off-by: David Bauer <mail@david-bauer.net>
Configure the PLMN and APN to the modem. This is required in cases,
where either the SGSN or GGSN does not permit the selection of IPv4v6
pdp type.
Previously, the modem always tried to establish a dual-stacked PDP
context regardless of the configured PDP type in uci. As this setting
can not be parameterized when creating a WDS context, configure it to
the modems internal list of profiles. This way, the PDP type is taken
into account when creating the WDS context.
Signed-off-by: David Bauer <mail@david-bauer.net>
The PLMN selection was reset when calling network-register, thus
rendering the sepcific selection of a carrier unapplied.
Set the PLMN selection after executing network-register. This seems to
cause the modem to re-select the carrier eventually.
That being said, qmi does allow the parameterization of the
network-register to include dpecific PLMN settings, however this is
currently not implemented in uqmi.
Signed-off-by: David Bauer <mail@david-bauer.net>
Set the RAT preference before attaching. This handles cases better,
where a network might be available but not with the preferred RAT.
If RAT is changed to a non-available RAT after attach, QMI does not fail
with missing registration but with failing to establish a PDP session.
Signed-off-by: David Bauer <mail@david-bauer.net>
Increase the wait time before polling the connection state for the first
time.
Depending on the prior state of the modem, the first poll might still
return a connected state. The script then tries to establish a PDP
session, which subsequently fails as the modem by then is in scan state.
Increasing the wait-time to 3 seconds mitigates this from happening.
Signed-off-by: David Bauer <mail@david-bauer.net>
On some network-triggered disconnections the UIM state might end up in
"illegal". This prevents the modem from attaching to any network in
non-restricted service modes.
Detect this state and reset the SIM card. This way, the modem can attach
to networks again.
Signed-off-by: David Bauer <mail@david-bauer.net>
Failing the registration does not necessarily mean we can not bring this
interface up. For example, roaming SIM cards are possibly steered by the
home-operator.
Don't block restart of the QMI interface in this case.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a struct_group to around all members in struct ath_cycle_counters.
It can help the compiler detect the intended bounds of the memcpy() and
memset().
This patch fixes the following build warning:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at /home/db/openwrt/build_dir/target-mips_24kc_musl/linux-ath79_generic/backports-6.1.24/drivers/net/wireless/ath/ath9k/main.c:140:3:
./include/linux/fortify-string.h:314:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
314 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Specifications:
SoC: QCA9531(650MHz)
RAM: DDR2 128M
Flash: SPI NOR 16M + SPI NAND 128M
WiFi: 2.4GHz with 2 antennas(WiFi/Thread)
Ethernet:
1xLAN(10/100M)
2xWAN(10/100M)
Button: 1x Reset Button
Switch: 1x Mode switch
LED: 1x Blue LED + 1x White LED + 1x Orange LED
IOT: Thread + ZigBee/Zwave
By uboot web failsafe:
Push the reset button for 5 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xc22): relocation R_MIPS16_26 against `libxt_DNAT_init' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol printf
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xcc8): relocation R_MIPS16_26 against `luaL_argerror' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x4194): relocation R_MIPS16_26 against `cil_printf.lto_priv.0' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol memcmp
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled:
<artificial>:(.text.exit+0x6e): relocation R_MIPS16_26 against `pthread_key_delete' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol stpcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x400c): relocation R_MIPS16_26 against `iwinfo_close' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
Currently the zram default compressor choice is displayed whether or not
zram is activated. Since the default choice is lzo-rle, this adds a
false dependency on kmod-lib-lzo.
With this patch, the choice options appear only when activating zram.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Fix the building issue setting CC to KERNEL_CC in kernel.mk. The
kernel backports by default uses CC to compile kconf. A new patch is
added to mac80211 to compile kconf with host gcc.
Signed-off-by: Zeyu Dong <dzy201415@gmail.com>
[ refresh patches ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
d8118f6 config: make sure timer is not on the timeouts list before freeing
4bbc6e7 add hostsfile output in addition to statefile
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Commit 572ea68070 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.
Fixes: #13724
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Furong Xu <xfr@outlook.com>
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
GND RXD TXD, beginning from the external antennas. 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet
Wlan:
* 4x4 in 2.4GHz : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)
Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A
Mounting: Wall and ceiling
```
```
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to the console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Contains the following update:
52a1c29 ipq8074: add Netgear WAX630 Board file for Netgear WAX630. Extracted from stock (WAX630_BDF.bin) firmware and repacked.
e7701b8 ipq8074: update RegDB in new submitted BDF
cd04ab7 qcn9074: update RegDB in new submitted BDF
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Remove ABI version, since its format is not accepted by the linker.
Enable rpath to avoid clash with system libraries
Signed-off-by: Felix Fietkau <nbd@nbd.name>
CONFIG_USB_AUDIO is a "USB Audio Gadget" driver, not a usb device driver
CONFIG_USB_AUDIO is "USB Audio support" before linux 2.6
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Expose the temperature sensors as hwmon, it improves the overall
user experience since on tiny boards the nvme can become a substantial
source of heat.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Major changes between OpenSSL 3.0.11 and OpenSSL 3.0.12 [24 Oct 2023]
* Mitigate incorrect resize handling for symmetric cipher keys and IVs. (CVE-2023-5363)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
c8c9f10 uim: fix help formatting
aac0776 uqmi: add APN profile commands
ffc5eea uim: support SIM card power-up/down
d6c963d uim: add application state to SIM status
Signed-off-by: David Bauer <mail@david-bauer.net>
The IXP4xx crypto module must be loaded after the rootfs is
up as it depends on loading some NPE microcode from the file
system.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The firmware package for the IXP4xx microcode was deleted but
the source files are still in the file cache so we can easily
resurrect it.
The firmware either supports ethernet (the most common) or
WAN (less common), image targets select the firmware they
want depending on usecase.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sometimes it's useful to be able to prepend to a variable as
well, such as when dealing with domain names, e.g.
prepend fdqn "$subdomain" "."
will result in:
fqdn="$subdomain.$fqdn"
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch
a new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global
priv->pll_clk_rate field. This will cause to have a reduced
clock rate on each subsequent SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Some packages (like wavemon >= 0.9.4) depend on libnl-cli. Add support
for this part of the lib. libnl-cli itself depends on libnl-genl and
libnl-nf. On MIPS, this component adds 81kB.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(punctuation correction and reorganisation of commit message)
Signed-off-by: Nick Hainke <vincent@systemli.org>
1) clear nvram partialboots upon successful boot
This behavior is already defined for EA9500; enabled for EA9200 too.
2) fix MAC address in board.d/02_network
Use the correct nvram variable to derive lan/wan MAC address.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
When using an external toolchain, ldd is not linked into the rootfs.
This causes subsequent upgrades to fail with 'Failed to exec upgraded'.
This patch adds the symlink when using an external toolchain and musl.
Signed-off-by: Arien Judge <arienjudge@outlook.com>
Make use of new toolchain define. TOOLCHAIN_DIR should be used only for
toolchain related packages and for everything else TOOLCHAIN_ROOT_DIR
and other define should be used instead.
Switch to new entry where possible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some packages won't ever have something to patch as they normally
install files or are meta-packages.
For these special packages, disable QUILT refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The option 31 in the RA specifies the DNS search list, the support
to configure this via UCI is missing in case dnsmasq-dhcpv6 is used.
This commit uses the uci option domain (same as is done by odhcpd) to
read and pass the DNS search list to dnsmasq, which is then used by RA.
Hence, with this commit, we are able to configure DNS search list for the
RA messages via the uci config when dnsmsaq-dhcpv6 is used.
Signed-off-by: Rahul Thakur <rahul.thakur@iopsys.eu>
To support the IXP42x platforms we need a kernel module
for the Epson R7301 RTC so we can load it as an optional
module.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
To support the IXP42x platforms we need a kernel module
for the X1205 RTC so we can load it as an optional module.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The lib-chacha20 library is missing build rules for big endian
ARM, and since IXP4xx is big endian ARM we need those rules to
build for IXP4xx.
Suggested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a partial revert of the deletion of the IXP4xx
target: we restore the APEX boot loader so we can use it
for the NSLU2 and related targets.
The APEX upstream is as dead as it gets so I have applied
OpenWrts old patches on top of the never released
v1.6.10 version and forked it into an OpenWrt variant
on GitHub. If the upstream comes back alive I will
happily switch over to it.
The file refers to the external GitHub, I suppose when
integrating this patch the file should be copied to OpenWrts
file repository and the file link changed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ucidef_set_network_device_* functions in uci-defaults.sh disagree
on whether to use "network-device" or "network_device" in board.json.
With the additional caveat that jshn will translate hyphens (-) into
underscores (_). This casues problems in netifd which expected
"network_device" causing boards which depend on assigning MACs in
board.json via uci-defaults.sh (or jshn in general) to fail.
This commit addresses the issue by using network_device in
uci-defaults.sh.
The bug was uncovered in the forums here:
https://forum.openwrt.org/t/support-for-rtl838x-based-managed-switches/57875/2596
This was exposed by commit 4ebba8a05d ("realtek: add support for HPE
1920-8g-poe+") where the board_config_load call from 03_gpio introduced
the key normalization by jshn.
Fixes: 9290539ca9 ("base-files: allow setting device and bridge macs")
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Michael 'ASAP' Weinrich <michael@a5ap.net>
[ improve commit title, description and fix wrong Tested-by tag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
479c7f8676d9 cache: make record/hostname lookup case-insensitive
26c97a5a50bf ubus: add a browse flag for suppressing cached ip addresses
c286c51a9bd9 Fix AVL tree traversal in cache_record_find and cache_host_is_known
4035fe42df58 interface: use a global socket instead of per-interface ones
c63d465698c7 cache: dump hostname target from srv records
b42b22152d73 use hostname from SRV record to look up IP addresses
d45c443aa1e6 ubus: add array flag support for the hosts method
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changes in 1.3 (18 Aug 2023)
- Remove K&R function definitions and zlib2ansi
- Fix bug in deflateBound() for level 0 and memLevel 9
- Fix bug when gzungetc() is used immediately after gzopen()
- Fix bug when using gzflush() with a very small buffer
- Fix crash when gzsetparams() attempted for transparent write
- Fix test/example.c to work with FORCE_STORED
- Rewrite of zran in examples (see zran.c version history)
- Fix minizip to allow it to open an empty zip file
- Fix reading disk number start on zip64 files in minizip
- Fix logic error in minizip argument processing
- Add minizip testing to Makefile
- Read multiple bytes instead of byte-by-byte in minizip unzip.c
- Add memory sanitizer to configure (--memory)
- Various portability improvements
- Various documentation improvements
- Various spelling and typo corrections
Signed-off-by: Nick Hainke <vincent@systemli.org>
Improve EEPROME load patches. Reorganize and rework them.
The current patch are bugged and with the case of MTD loading, leaks and
never free the EEPROM read values.
Also add support for loading EEPROM using NVMEM cells.
As a cleanup, change the binding to swap EEPROM read from mtd to
ralink,eeprom-swap and generilize it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
All of the changes are various bugfixes, there is no new major feature.
Notable bugfixes are:
* WCN6855 board name fixes
* One MSI vector booting is working again
This is rather important for most of the older platforms.
* DFS CAC state in virtual interfaces was fixed
* TX power during CAC reporting
Signed-off-by: Robert Marko <robimarko@gmail.com>
DFS CAC time export is required for backport of a ath11k fix so lets
backport the required cfg80211 upstream commit as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changes:
6b2533c0 libnl-3.8.0 release
1558bd62 build: replace old "NOTE" in configure output and add summary
f66383a4 build: avoid aclocal warning about missing "m4" directory
e4402a4c build: run `autoupdate` for AM_PROG_LIBTOOL
5761b6af build: add "-Wno-portability" to AC_INIT_AUTOMAKE()
661f10a1 license: fix/adjust license for "src/nl-cls-add.c"
c8fcb412 license: fix/adjust license for "src/nl-addr-{add,delete,list}.c"
e3e6fd6d tests: use thread-safe localtime_r() instead of localtime()
f520471c lib/xfrm: use thread-safe gmtime_r() instead of gmtime()
be5add72 tests: avoid srandom()/random() in favor of _nltst_rand_u32()
40578a62 lib: use getprotobyname_r(), getprotobynumber_r() if available
8ee8b05f lib: fix error handling in nl_str2ip_proto()
09f03f29 tests: check nl_str2ip_proto()
74bffbf6 route: fix documentation comment for nl_nh_group_info
59f8db0d clang-format: add "-l" alias for option in "tools/clang-format.sh"
935cc90a clang-format: ignore reformatting commit in ".git-blame-ignore-revs"
53da4712 clang-format: reformat files with new format
65c43bfe clang-format: update ".clang-format" from linux kernel
4c39a2ce include: use <linux/$file> instead of <linux-private/linux/$file>
a1e9fb3d include/linux: add all linux headers that we use
d37ffe15 include/linux: update all linux headers
1af767a8 include: add missing "extern "C"" specifier to public headers
e0a5d12b all: drop "extern "C"" from internal code
d9a1e0ce build: add "check-local-build-headers" test target to build public headers
02b87012 build: add a "check-local" build target
f9413915 include: fix headers "include/netlink/route/{netconf.h,route/qdisc/red.h}" to be self-contained
680df173 idiag: "fix" license for "idiag-socket-details" tool
2f210d9a github: test build on alpine:latest for musl
dcc4c0a5 Revert "gitignore: ignore patch files"
39106309 github: add test for linking with mold and fail on unknown versions
f475c3b2 route/nh: drop not implemented "nh" API from headers
4c681e77 build: fix exporting symbol rtnl_link_info_ops_get
260c9575 include: don't explicitly include headers from "nl-default.h"
98c1e696 tests: cleanup include of netlink headers
42bec462 build: cleanup default include list in Makefile.am
4c1a119a include: include private linux headers with explicit path
ca063725 python: add make target for python build
25c90193 python: drop unused "python/netlink/fixes.h"
3f3da7fd gitignore: ignore python build artifacts
61ef5609 gitignore: ignore generated doc files
298c5dc6 include: drop "netlink-private/netlink.h" and move declarations
862eed54 all: cleanup includes and use "nm-default.h"
2b3cd741 include: add "nl-default.h" header
8952ce6f build: move "lib/defs.h" to "include/config.h"
1010776d include: split and drop "netlink-private/types.h"
d1d57846 include: rename "nl-shared-core" to "nl-priv-dynamic-core"
fc91c4f8 include: rename "nl-hidden-route" to "nl-priv-dynamic-route"
9bb6f770 include: rename "nl-intern-route" to "nl-priv-static-route"
b5195db9 genl: rename private header "nl-priv-genl.h" to "nl-genl.h"
0eacf658 include: make "netlink/route/link/{inet,inet6}.h" self-contained
ad014ad1 route/tc: avoid unalinged access in rtnl_tc_msg_parse()
05bd6366 add support for TC action statistics
776fc5a6 lib: move "include/netlink-private/object-api" to include/nl-shared-core
fad34560 lib: move "include/netlink-private/cache-api" to include/nl-shared-core
ed2be537 route: move "include/netlink-private/route/link/sriov.h" to lib/route/link-sriov.h
97f61eda lib: move "include/netlink-private/socket.h" to lib/nl-core.h
96e1cc5b route: move "include/netlink-private/route/nexthop-encap.h" to lib/route
391e03d3 route: merge "include/netlink-private/tc.h" to lib/route/tc-api.h
7fc4f5b3 route: move rtnl_tc_build_rate_table() to "tc-api.h"
cf41e14d route: move "include/netlink-private/route/tc-api.h" to lib/route
db810cfb route: move hidden symbols from "include/netlink-private/route/tc-api.h"
ff08e618 build: don't add lib/route to include directory for all libs
eb8da16d include: move "include/netlink-private/route/link/api.h" to lib/route
8b2074aa include: move "include/netlink-private/route/utils.h" to nl-intern-route
fd470c06 include: move "include/netlink-private/route/mpls.h" to "lib/mpls.h"
78056ad2 genl: add comment about wrongly exported symbol genl_resolve_id()
befc4ab4 include: move "include/netlink-private/genl.h" to "lib/genl/nl-priv-genl.h"
f6c26127 nl-aux: add "include/nl-aux-{core,route}" headers
2da8481b base: move "netlink-private/utils.h" to "base/nl-base-utils.h"
d3e9b513 include/utils: move nl-auto base defines to "utils.h"
543b9f8f clang-format: reformat "include/netlink-private/nl-auto.h"
aa565460 route: cleanup ATTR_DIFF() macros
beba5a18 cli: add nl-nh-list utility
780d06ae route: add nh type
1b6433d9 neigh: add support of NHID attribute
e0140c5f include: import kernel headers "linux/{neighbour,nexthop,rtnetlink}.h"
eef06744 utils: add static-assert for signedness of arguments of _NL_CMP_DIRECT() macro
679c4c51 cli: use <netlink-private/utils.h> in cli and _nl_{init,exit}
a9c5de52 lib: use _nl_{init,exit} instead of __{init,exit}
102f9bd2 include/private: add _nl_init/_nl_exit macros
6782678e include/private: drop unused __deprecated macro
a0535a58 all: use "_nl_packed" macro instead of "__attribute__((packed))"
8c9f98cf all: rework ATTR_DIFF() macros to not generate attribute names
ca34ad52 lib: handle negative and zero size in nla_memcpy()
859b89dc include: drop now unused min()/max()/min_t()/max_t() macros
2e0ae977 all: use _NL_{MIN,MAX}() macros
57c451fa utils: add various helpers to "include/netlink-private/utils.h"
a9a9dcea style: format "include/netlink-private/utils.h" with clang-format
590e8a61 tools: improve failure message with "tools/clang-format.sh -n"
06dc5ae0 github: fix format checking with clang-format
7738f239 route/trivial: sort entries in "libnl-route-3.sym" asciibetically
fc805c56 route/bond: Add support for link_info for bond
6af26981 lib: accept NULL argument in nla_nest_cancel() for robustness
e9662091 macsec: Drop offload capability validation check
35a68109 github: update flake8 linter to not explicitly select checks
9a266405 python: add ".flake8" file for configuring "flake8"
e6b934a5 python: fix flake8 warnings E712
2cea738b python: fix flake8 warnings E711
d561096c python: fix flake8 warnings E302
29b06d0f python: fix flake8 warnings E741
4dc1f498 python: fix flake8 warnings F841
f4875c69 python: fix flake8 warnings W605
9a3d91df python: fix flake8 warnings F401
6baf2339 clang-format: add "tools/clang-format-container.sh" script
ee2876e3 github: add test for checking clang-format style
45c7aae3 clang-format: add "tools/clang-format.sh" script
02e0fd3f github: check python-black code formatting in github actions
2dd53895 build: add ".git-blame-ignore-revs" file for "blame.ignoreRevsFile" git config
3c753e3c python: reformat all Python files with python-black
298ee58e python add "pyproject.toml" for configuring black
a0e4b7f9 github: skip Python flake8 test with clang build
c4240c0b github: run "Build Release" test also with clang
143cee1d bridge: fix bridge info parsing
96bbe55c test-cache-mngr: Flush output after object dumps
cf5dcbcd test-cache-mngr: Add option to print timestamps
bd570952 test-cache-mngr: Add an option to iterate over all supported address families
bf80da90 test-cache-mngr: Add dump interval options
80febeea test-cache-mngr: Add an option to control which oo_dump function is used
6519a917 route/link: prevent segfault in af_request_type()
a68260f8 github: fix installing python dependencies via pip
39c04bc7 build: drop redundant "autogen.sh" call from "tools/build_release.sh"
d411b88d build: change proper working directory in "doc/autogen.sh"
2fa73ce0 build: ensure "autogen.sh" scripts fail on error
fc786296 gitignore: ignore "*~" files
4c4e614b docs: rtnl_link_put() 'releases' instead of 'returns'
336b15dc include/linux: update copy of kernel header "linux/ipv6.h"
e2cacc26 route/link: improve handling of IFLA_INET6_CONF
ec8c493c route/link: remove rtnl_link_inet6_set_conf() API
e790f8ad route/link: various fixes for rtnl_link_inet6_get_conf() API
d83c6d54 route/link: add accessor API for IPv6 DEVCONF
9167504d bridge: drop unnecessary goto in bridge_info_parse()
984d6e93 bridge: don't normalize the u8 argument in rtnl_link_bridge_set_vlan_filtering() to boolean
3662a5da bridge: expose rtnl_link_bridge_get_vlan_protocol() in host byte order
5a1ef219 bridge: fix parsing vlan-protocol in bridge_info_parse()
ad1c2927 bridge: minor cleanups in "bridge_info.c"
1c74725a bridge: use SPDX license identifiers in bridge_info files
26ca549d bridge: reformat bridge_info file with clang-format
08dc5d9c bridge: extend libnl with options needed for VLAN aware forwarding
7391a38e bridge: Add support for link_info of a bridge
1f1e8385 route/vlan: drop unnecessary "else" in vlan_put_attrs()
2bc30e57 route/vlan: fix error handling in 'lib/route/link/vlan.c'
8273d6ce build: add comments to linker version scripts about the version tags
6ac7a812 doc: fix typo
07d274ab doc: fix typo
0461a425 attr: reject zero length addresses
8d40d9eb route: construct all-zero addresses for default route destination
25d42a4f addr: allow constructing all-zero addresses
0c0aee82 addr: create an all-zero addresses when parsing "any" or "default"
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
16d68ab Release libmd 1.1.0
054bca1 build: Terminate lists in variables with «# EOL»
84d269e test: Add cases for SHA224 and SHA512-256
a677e68 test: Add a new test_eq() helper function
4c5931f Sync SHA2 changes from OpenBSD
9934d94 Sync SHA1 changes from OpenBSD
457e30a Sync RMD160 changes from OpenBSD
b2e54bc Sync MD5 changes from OpenBSD
ee56a52 Sync MD4 changes from OpenBSD
b9496ac Sync MD2 changes from NetBSD
09d5824 Remove unused <assert.h>
08b2c5d build: Rename libmd_alias() to libmd_strong_alias()
ed69599 On Darwin use assembler to support symbol aliases
b74b777 build: Do not use strong aliases on macOS
94838ec build: Require automake 1.11
39cbc7b build: Fix configure.ac indentation
4620a04 build: Switch to debian:latest Docker image
e408786 build: Fix version script linker support detection
0ef1e4d doc: Move mailing list reference to the end
a3f1671 man: Add new libmd(7) man page
Signed-off-by: Nick Hainke <vincent@systemli.org>
There are a few targets that mess with the atm kernel headers. To avoid
incompatibility between kernel and user space during compilation, the
correct headers should be used.
Consequently, the package must also be marked as nonshared.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/
SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
4pin Serial Header | 3.3 | GND | RX | TX
MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env
* Installation via either RJ45 console or on-board 4 PIN header
Install Method
--------------
1) Setup TFTP server, and place
openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
(use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
set bootcmd 'ping 192.168.1.1; run boot_flash'
saveenv
8) TFTP image to RAM:
tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin
Signed-off-by: Glen Lee <g2lee@yahoo.com>
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. So qmi.sh is hanging on the first call. Since 2020 uqmi
supports a timeout parameter. Unfortunately qmi.sh didn't make use of
this parameter. So qmi.sh is now invoking an early dummy access to
unlock the modem
Signed-off-by: Uwe Niethammer <uwe@dr-niethammer.de>
Add missing PKG_MIRROR_HASH. This is always needed as is used to
generate and use a tar instead of git clone and validate the hash of it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Improve and update instructions on how to add board files and both
describe the needed step to upstream a board file or to use it locally.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The PKG_MIRROR_HASH is wrong, fix it.
Found and fixed using this command:
make package download check FIXUP=1
Fixes: c123e4f053 ("rtl8812au-ct: bump to fix kernel 6.1 compile")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Recent hostapd changes just edited the ucode files. It is required to
bump the PKG_RELEASE to include the newest changes in the latest builds.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The mt76 driver usually reads the eeprom on the mtd partition at dts.
For emmc device we need to use caldata_extract script to read the
eeprom. However, the default eeprom file breaks the caldata script
execution, so remove it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
When adding new router support, I found that uboot
could not recognize flash: "unknown raw ID xxx".
Sync SPI-NAND driver for mediatek to fixes this:
* Add support for Winbond W25N01KV 1Gbit chip.
* Add support for Etron SPI-NAND chip.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
If the full interface is restarted while bringing up an AP, it can trigger a
wpa_supplicant interface start before wpa_supplicant is notified of the
allocated mac addresses.
Fix this by moving the iface_update_supplicant_macaddr call to just after
the point where mac addresses are allocated.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The previous code handling the equal-condition might be removed or
altered in the future and the case might be overlooked.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Some users have their routers configured to supply a DHCP range that
includes the local interface address.
That worked with dnsmasq because it automatically skips the local
address.
Re-enable those existing configurations for the release and hint at
possible future problems.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
[ wrap commit description and remove unecessary text ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
To avoid confusion when working with ipcalc.sh, clarify that the last two
parameters belong to the range calculation and rename 'num' to the slightly
less ambiguous 'size'.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
In the dnsmasq init script, an off-by-one in the range calculation of
ipcalc.sh was mitigated by passing the limit as if its counting started
at zero. This patch removes the mitigation as the off-by-one has been
fixed.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Add a function 'ipcalc' to /lib/functions.sh that sets variables more
safely using export.
With this new function, dnsmasq also handles the return value of ipcalc
correctly.
Fixes: e4bd3de1be ("dnsmasq: refuse to add empty DHCP range")
Co-Authored-By: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Printing a broadcast address doesn't make any sense for /31 and /32
prefixes.
Strictly speaking, the same goes for the network address but it is useful
to get the first address in the prefix, e.g. to create a canonical
CIDR notation "$NETWORK/$PREFIX".
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
For /31 and /32 prefixes, there are only host addresses - no network and
broadcast address with all-zero and all-one bits.
Reflect this when setting the limit.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
The start and end addresses are inclusive.
Thus, adding num without substracting one results in num + 1 addresses.
Add the substraction and to implement the documented behaviour.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
- detect die revision used in variants of the Allwinner H616 SoC (H313, T507)
- support for H6 boards without PMIC
Tested on Pine64+ and Orange PI Zero2
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
allow to overwrite the detected system capabilities e.g. if devices
does not operate as bridge.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
Use the header closest to LED 4 and 5.
They are marked with a white stroke.
TX RX GND, beginning from "4". 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)
Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)
Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```
```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Changes between 3.0.10 and 3.0.11 [19 Sep 2023]
* Fix POLY1305 MAC implementation corrupting XMM registers on Windows. ([CVE-2023-4807])
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
The patch refresh accidentally moved the hostapd_ucode_free_iface call to
the wrong function
Fixes: e9722aef9e ("hostapd: fix a crash when disabling an interface during channel list update")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When adding builds for MT7981 the related Makefile sections for MT7986
have apparently been copied, but in one instance the rename from 7986 to
7981 has been omitted. Fix that now.
Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
In order to use the same image for both boards, U-Boot is responsible for
detecting the revision and enabling/disabling DTS nodes.
So, to make it easy for users, lets add the pending U-Boot patches to build
in OpenWrt.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Package and add dependencies to drm-amdgpu and drm-radeon for 6.1
* package acpi-video, drm-display-helper and drm-buddy
* add acpi-video, drm-display-helper and drm-buddy as dependencies for
drm-amdgpu
* add acpi-video and drm-display-helper as dependencies for drm-radeon
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Synchronize the ath11k backports with the current ath-next tree.
All of the changes are various bugfixes, there is no new major feature.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ed3725e15a154ebebf44e0c34806c57525483f92
("wifi: ath11k: Fix qmi_msg_handler data structure initialization")
has been present upstream since 6.1.2 but it seems Quilt refreshed it
wrongly so it appeared like a completely different patch.
Commit 7c15430822e71e90203d87e6d0cfe83fa058b0dc
("wifi: ath11k: allow system suspend to survive ath11k")
has been present upstream since 6.1.16 but somehow quilt still happily
applied it.
So, drop both of them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is needed for ksh/bash style process substitution such as
<(command) and >(command) which was introduced in ash as of busybox
version 1.34.0 to work.
Signed-off-by: Erik Karlsson <erik.karlsson@genexis.eu>
General support for 9P is desirable on platforms without virtualization.
This decouples the 9P general networking support for use on more platforms.
Signed-off-by: Daniel Maslowski <info@orangecms.org>
When STA is disconnected, ensure that the interface is in a cleanly stopped
state:
- if in regular enable/disable state, stop beacons if necessary
- in any other state, disable the interface
When the STA is up, ignore repeated start commands for the same channel, in
order to avoid unnecessary AP restarts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
8e6485a1bcb0 PEAP client: Update Phase 2 authentication requirements
de9a11f4dde9 TTLS client: Support phase2_auth=2
b2a1e7fe7ab9 tests: PEAP and TTLS phase2_auth behavior
518ae8c7cca8 P2P: Do not print control characters in debug
a4c133ea73c7 WPS: Optimize attribute parsing workaround
7a37a94eaa0d Check whether element parsing has failed
f80d83368818 ACS: Remove invalid debug print
fb2b7858a728 FILS: Fix HE MCS field initialization
50ee26fc7044 P2P: Check p2p_channel_select() return value
a50d1ea6a2b3 Add QCA vendor attributes for user defined power save parameters
4636476b7f22 Set RRM used config if the (Re)Association Request frame has RRM IE
e53d44ac63e8 AP MLD: Use STA assoc link address in external auth status to the driver
99a96b2f9df7 AP MLD: OWE when SME is offloaded to the driver
96deacf5d710 nl80211: Skip STA MLO link channel switch handling in AP mode
d320692d918a AP MLD: Handle new STA event when using SME offload to the driver
faee8b99e928 tests: Fix eht_mld_sae_legacy_client to restore sae_pwe
c3f465c56c94 wlantest: Handle variable length MIC field in EAPOL-Key with OWE
605034240e0c wlantest: Support multiple input files
053bd8af8ed2 Recognize FTE MLO subelements
43b5f11d969a Defragmentation of FTE
3973300b8ded FTE protected element check for MLO Reassociation Response frame
74e4a0a6f1e4 wlantest: Learn AP MLD MAC address from Beacon frames
a5a0b2cf7b1b wlantest: Find non-AP MLD only from affiliated BSSs of the AP MLD
74472758584d wlantest: Recognize non-AP MLD based on any link address for decryption
1ffabd697c67 wlantest: Learn non-AP MLD MAC address from (Re)Association Request frames
4e8e515f92b9 wlantest: Use MLO search for the STA in reassociation
49bf9f2df95a wlantest: Use the MLD MAC address as well for matching STA entries
5434a42ec69c wlantest: Search for FT Target AP using MLD MAC address as well
a19fcf685cae wlantest: Include the MLD MAC address of the AP MLD in new-STA prints
709d46da73da wlantest: Do not claim update to AP MD MAC address if no change
770760454f9e wlantest: Do not update BSS entries for other AP MLDs in PTK cloning
084745ffc508 Add QCA vendor attributes for NDP setup
bf9cbb462fd9 Fix writing of BIGTK in FT protocol
011775af9443 tests: Check for beacon loss when using beacon protection
8f148d51322f Fix a compiler warning on prototype mismatch
b7db495ad9c9 AP: Fix ieee802_1x_ml_set_sta_authorized()
232667eafe0d Fix CCMP test vector issues
30771e6e05ed Include PTID in PV1 nonce construction for CCMP test vector
34841cfd9aba Minor formatting changes to CCMP test vectors
a685d84139e6 BSS coloring: Fix CCA with multiple BSS
bc0636841a70 wpa_supplicant: Fix configuration parsing error for tx_queue_*
2763d1d97e66 hostapd: Fix AID assignment in multiple BSSID
763a19286e2f AP: Add configuration option to specify the desired MLD address
bd209633eb10 AP: Use is_zero_ether_addr() to check if BSSID is NULL
bc0268d053b4 wlantest: Guess SAE/OWE group from EAPOL-Key length mismatch
a94ba5322803 EHT: Support puncturing for 320 MHz channel bandwidth
7e1f5c44c97e EHT: 320 MHz DFS support
6f293b32112a QCA vendor attributes for updating roaming AP BSSID info
5856373554eb Extend QCA vendor command to include more parameters for netdev events
e080930aa0a5 Define QCA vendor roam control RSSI attributes
fe72afe713ad Define QCA vendor attribute for high RSSI roam trigger threshold
47a65ccbfde2 P2P: Clean wpa_s->last_ssid when removing a temporary group network
884125ab7d21 tests: P2P autonomous GO and clearing of networking information
7637d0f25053 P2P: Do not filter pref_freq_list if the driver does not provide one
dd1330b502ff Fix hostapd interface cleanup with multiple interfaces
0a6842d5030e nl80211: Fix beacon rate configuration for legacy rates 36, 48, 54 Mbps
d606efe054d5 tests: Beacon rate configuration for 54 Mbps
f91d10c0e6aa tests: Update RSA 3k certificates
07d3c1177bbb tests: Make sae_proto_hostapd_status_* more robust
1085e3bdc6f6 Update iface->current_mode when fetching new hw_features
338a78846b44 Add a QCA vendor sub command for transmit latency statistics
9318db7c38bc wlantest: Use local variables for AA/SPA in FT Request/Response processing
628b9f10223d wlantest: Derive PMK-R1 and PTK using AA/SPA for MLO FT over-the-DS
104aa291e5c8 wlantest: Fix FT over-the-DS decryption
37c87efecfe3 wlantest: Search SPA using MLO aware find for FT Request/Response frame
19f33d7929e8 wlantest: Learn the Link ID for AP MLD affiliated BSSs
6ae43bb10323 wlantest: Learn link address for assoc link from (Re)Association Request
4c079dcc64da Increment hmac_sha*_vector() maximum num_elem value to 25
e6f64a8e1daf FT: FTE MIC calculation for MLO Reassociation Request frame
a83575df5994 wlantest: FTE MIC calculation for MLO Reassociation Request frames
ff02f734baf8 wlantest: Allow specific link BSS to be found with bss_find_mld()
7381c60db8f0 FT: Make FTE MIC calculation more flexible
ac9bf1cc2a4c Decrement hmac_sha*_vector() maximum num_elem value to 11
aa08d9d76803 Fix use of defragmented FTE information
78b153f90a74 Calculate defragmented FTE length during IE parsing
8cf919ffd5c4 wlantest: FTE MIC calculation for MLO Reassociation Response frame
d12a3dce82a9 wlantest: Store and check SNonce/ANonce for FT Authentication
20febfd7838d wlantest: Dump MLO association information in debug
609864d6a8a1 Add QCA vendor attribute to configure MLD ID in ML probe request
12154861e24a Add support for conversion to little endian for 24 bits
c437665041c0 Add Non EHT SCS Capability in (Re)Association Request frames
33da386553b7 SCS: Add support for QoS Characteristics in SCS request
edfca280cbe8 SCS: Add support for optional QoS Charateristics parameters
32dcec9529ec Send actual MFP configuration when driver takes care of BSS selection
123d16d860fa Update hw_mode when CSA finishes
b3d852560bda Change QCA vendor configure attribution name of peer MAC address
12fabc4765c2 Add QCA vendor attribute for configuring max A-MPDU aggregation count
f6eaa7b729cb Add QCA vendor attribute for TTLM negotiation support type
f6dcd326fea7 wlantest: Indicate ToDS/FromDS values for BSS DATA entries
6ce745bb87d4 wlantest: MLO support for decrypting 4-address frames
850dc1482953 wlantest: Remove duplicated A1/A2/A3 override detection for MLO
770e5a808fbb wlantest: Determine whether A1 points to STA once in rx_data_bss_prot()
377d617b574a Define new BSS command info mask for AP MLD address
d3ab6e001f62 wlantest: Use non-AP MLD's MLD MAC address in FT over-the-air derivation
a845601ffe32 wlantest: Derive PTK in MLO using MLD MAC addresses for FT over-the-air
0cd2bfc8a402 wlantest: Fix FTE MIC calculation for MLO Reassociation Response frames
528abdeb673b wlantest: Learn group keys from MLO FT Reassociation Response frames
990600753dd9 wlantest: Defragment Basic MLE before processing
de043ec01ab5 wlantest: Defragment the Per-STA Profile subelement
bae1ec693c44 wlantest: Minimal parsing of Basic MLE STA Profile
ba1579f3bf7c Clear BIGTK values from wpa_supplicant state machine when not needed
b46c4b9a916a tests: Beacon protection and reconnection
3e71516936b7 Document per-ESS MAC address (mac_addr=3 and mac_value)
f85b2b2dee3b Extend wpa_parse_kde_ies() to include EHT capabilities
e3a68081bc1e driver: Add option for link ID to be specified for send_tdls_mgmt()
c7561502f2e8 nl80211: Use a QCA vendor command to set the link for TDLS Discovery Response
a41c8dbdd84e TDLS: Copy peer's EHT capabilities
626501434be1 TDLS: Learn MLD link ID from TDLS Discovery Response
5f30f62eead7 TDLS: Reply to Discovery Request on the link with matching BSSID
940ef9a05c0f TDLS: Use link-specific BSSID instead of sm->bssid for MLO cases
f429064189c3 TDLS: Set EHT/MLO information for TDLS STA into the driver
dd25885a9daa Remove space-before-tab in QCA vendor related definitions
af6e0306b2a9 Fix typos in QCA vendor related definitions
4c9af238c1e4 Fix inconsistent whitespace use in QCA vendor related definitions
e5ccbfc69ecf Split long comment lines in QCA vendor related definitions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MAC address and interface name assigned by mac80211.sh depend on the order in
which interfaces are brought up. This order changes when interfaces get added
or removed, which can cause unnecessary reload churn.
One part of the fix it making MAC address allocation more dynamic in both
wpa_supplicant and hostapd, by ignoring the provided MAC address using
the next available one, whenever the config does not explicitly specify one.
The other part is making use of support for renaming netdevs at runtime and
preserving the MAC address for renamed netdevs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When a device has more than one reserved mac address, they can be used for
virtual interfaces without the local bit in the first byte
Signed-off-by: Felix Fietkau <nbd@nbd.name>
set_config causes the ucode bss resource to be re-created and because of that
the bss list needs to be updated as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Known issues:
IPV6 connectivity problem, see: https://github.com/openwrt/openwrt/pull/13203#issuecomment-1666947749
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Co-authored-by: Richard van Schagen <vschagen@icloud.com>
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Add 2 seconds sleep after each forcibly killed/tried-to-kill process
in the final process termination loop in sysupgrade stage2.
This is needed especially for qualcommax/ipq807x, where ath11k
wireless driver may have a long 10-20 seconds delay after termination
before actually getting killed. This often breaks sysupgrade.
The current KILL loop in kill_remaining does all 10 kill attempts
consecutively without any delay, as evidenced here in a failing sysupgrade.
It does not allow any time for the process to finalize its internal
termination.
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2122)
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2122)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Failed to kill all processes.
sysupgrade aborted with return code: 256
The change in this commit adds a 2 seconds delay after each kill attempt
in order to allow some processes to more gracefully handle their
internal termination.
The result is like this:
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2309)
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2324)
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending signal KILL to hostapd (2309)
[ 699.827521] br-lan: port 7(hn5wpa2r) entered disabled state
[ 699.908673] device hn5wpa2r left promiscuous mode
[ 699.908721] br-lan: port 7(hn5wpa2r) entered disabled state
[ 701.038029] br-lan: port 6(hn5wpa3) entered disabled state
Sun Sep 3 11:15:16 EEST 2023 upgrade: Sending signal KILL to hostapd (2324)
[ 702.058256] br-lan: port 5(hn2wlan) entered disabled state
[ 709.250063] stage2 (8237): drop_caches: 3
Sun Sep 3 11:15:25 EEST 2023 upgrade: Switching to ramdisk...
The delay introduced here only kicks in if there is some process that
does not get terminated by the first TERM call. Then there is at least
one 2 sec wait after the first KILL loop round.
This commit is related to discussion in PRs #12235 and #12632
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Reviewed-by: Robert Marko <robimarko@gmail.com>
With recent updates of TF-A the previously already fixed bug slipped
back into the source tree. Again, reorder bl2 init for MT7622 and
initialize WDT only after DRAM init has completed to avoid the
notorious hang.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board.
Add pre-built files to fix swig dependencies.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- USB Host:
1 x USB3.0 Type A HOST
1 x USB2.0 OTG (40-pin pin-header)
- Wireless:
RTL8723DU/RTL8821CU
- Power Supply: Type-C 5V
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Changes:
9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH)
111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines
ae1421f wireless-regdb: Update regulatory info for Türkiye (TR)
20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023
991b1ef wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f429bd94f99e system-linux: switch to new ETHTOOL_xLINKSETTINGS API
Fixes AN announcement for speeds beyond 1 GBit/s.
Adds new UCI options for Ethernet devices:
- autoneg: switch on or off auto-negotiation
- pause: if set to 0, do not announce symmetric flow control capability
- asym_pause: if set to 0, do not announce asymmetric flow control
capability.
- rxpause: if set overrides AN and forces RX pause accordingly
- txpause: if set overrides AN and forces TX pause accordingly
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
db3934d2f740 scripts/netifd-wireless.sh: properly fix WPA3 Enterprise support
Support the following values for the different WPA3 Enterprise modes:
- wpa3-mixed: WPA3 Enterprise transitional mode
This supports EAP with both SHA1 and SHA-256, with optional MFP
- wpa3: WPA3 Enterprise only mode
This supports only SHA256 with mandatory MFP
- wpa3-192: WPA3 Enterprise with mandatory 192 bit support
This uses only GCMP-256 ciphers
Disable 192 bit support and GCMP-256 ciphers for the regular "wpa3" mode.
It seems that even leaving in optional 192 bit support breaks auth on some
clients, including iOS devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
WPA3 Enterprise-transitional requires optional MFP support and SHA1+SHA256
WPA3 Enterprise-only requires SHA1 support disabled and mandatory MFP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems that this was not functioning properly and was likely completely unused.
Keeping this out of tree also introduced some annoying churn when updating, because
of the iw nl80211.h sync patch.
If this is needed, it will be reintroduced when/if it is added upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Arm platforms with the right hardware blocks (such as
GICv3.0+ interrupt controller and SMMU/IOMMU) are
able to use vfio-pci to pass through PCI devices
to a VM.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The vfio module only exposes the enable_unsafe_noiommu_mode parameter
if CONFIG_VFIO_NOIOMMU is enabled. When it isn't, the module
will complain about an unknown parameter:
vfio: unknown parameter 'enable_unsafe_noiommu_mode' ignored
As CONFIG_VFIO_NOIOMMU is disabled by the module package,
we can remove the module loading parameter.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Always enable built-in 2.5G PHY on MT7988 for now, so that it can be
used. In future it would be nice to be able to switch power and MDIO
access via address 0 at run-time in Linux, both, to be able to use
external PHYs at address 0 and to reduce power consumption on systems
not using the built-in 2.5G PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The U-Boot build for the MT7988 reference board booting from SD card
wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build
even though the 'comb' variant is used. Fix that dependency.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While the v2 is nearly identical to v1, v3 uses a different PHY and
needs a different build for Ethernet to work in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Select many potentially useful options for the MT7988 RFB U-Boot builds.
The resulting loader is intended as a development tool and intends to be
generic. It does *not* have a default bootcmd set, but allows to boot
pretty much everything, including EFI executables.
To install this U-Boot build to the eMMC:
opkg install mmc-utils partx-utils
mmc bootpart enable 1 1 /dev/mmcblk0
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0
partx -a /dev/mmcblk0
dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Compile-tested: all boards
Runtime-tested:
- Cortex-A8: pcDuino
- Cortex-A7: Bananapro, Bananapi M3
- Cortex-A53:Pine64+
Notes:
- binman tries to add firmware for the SCP (system control processor), which
we don't build, and is optional for the boot process on 64-bit. Disable this
via setting the SCP envvar to /dev/null. For further info, see [1] .
[1] https://github.com/u-boot/u-boot/blob/master/board/sunxi/README.sunxi64
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
vhost-net is used to accelerate traffic to virtualisation
guests that use the virtio-net network card in QEMU.
Generally it is invoked by specifying "vhost=on" to a
QEMU -netdev device:
qemu-system-aarch64 -nographic -M virt -cpu host \
--enable-kvm -bios u-boot.bin -smp 1 -m 2048 \
-drive file=openwrt-armsr-armv8.img,format=raw,index=0,media=disk \
-device "virtio-net,netdev=landev,disable-legacy=off,disable-modern=off" \
-netdev "tap,id=landev,helper=/usr/lib/qemu-bridge-helper --br=br-lan,vhost=on"
Signed-off-by: Mathew McBride <matt@traverse.com.au>
We have to move to use git clone as there are no newer tagged releases.
Changes:
604f8f5 Default CROSS_CM3 to arm-none-eabi- instead of armv7m-softfloat-eabi-
b9b9419 Tidy up license information
0290b2c wtmi: Fix typo
a10b8e9 Makefile: fix a53-firmware.bin generation (maximum size is not optimal)
f654082 wtmi: Add const qualifier to isr_vector
4a43a3b wtmi: Improve detection of ESPRESSObin boards with Topaz
189e629 wtmi: Improve detection of boards with insufficient MDIO pull-up
3dac4fe wtmi: Fix detection of Armada 3720 Devel Board
3ca4dfa Bump mox-imager commit
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
1de442d Convert floating point operations to integer operations
ce6770d Modify mv_ddr4_calibration_validate function body to match function header
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
a3e1c67 wtmi: Fix linker output sections
f65e3bf wtmi: Remove usage of non-existant string.h file and memcpy() function
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Recent envtools update to 2023.07.02 has introduced a breakage when trying
to parallel build with the following error:
/bin/sh: line 1: scripts/basic/fixdep: No such file or directory
Luckily it can easily be reproduced locally via a simple script so it was
not hard to bisect it down to upstream commit [1].
However, its not that commits fault, it just uncovered an issue with the
way we have been building envtools for a long time, maybe even from the
package introduction.
The issue is that we are trying to build envtools as one of the U-Boot
no-dot-config-targets but envtools was newer a valid target for it but
since we were creating the config headers that were not actually used it
was actually building all this time.
Since the blamed commit [1] a tool called printinitialenv is built and
now a proper config is actually required in order for prerequisites to
get built properly.
So, in order to properly fix this (Hopefully for good) lets stop pretending
that envtools are a valid no-dot-config-targets target and use the
tools-only defconfig which is meant exactly for just building the tools.
This will make a minimal config for the U-Boot sandbox target and then
envtools will build just fine in parallel mode (I tested with 32 threads).
We do hovewer need to override the ARCH passed by OpenWrt and set it to
sandbox as otherwise U-Boot will not find the required headers because the
ARCH is being overriden to an incorrect one.
[1] 40b77f2a3a
Fixes: 9db0330052 ("uboot-envtools: update to 2023.07.02")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
WED requires a bunch of additional reserved memory regions. As U-Boot's
LMB allocator defaults to a maximum of only 8 regions, this currently
makes using WED impossible.
Raise LMB_MAX_REGIONS to 64 just like for all other MediaTek boards
with a SoC supporting WED.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When the STA is brought up, it is set to DISABLED before adding the bss to ucode,
so the first trigger to disable the AP is missed.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During the channel scanning process, the driver will continuously
switch channels. It seems that the full RF calibration step in
rt2800_config_channel() caused the channel scanning function to
timeout. To fix it, move the RF calibration to rt2800_enable_radio()
so that it is only executed once. This commit also includes some
coding format adjustments to follow the Linux recommended style.
Fixes: 2824fa6963 ("mac80211: rework MT7620 PA/LNA RF calibration")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.
Signed-off-by: Stefan Agner <stefan@agner.ch>
I recently added support for the NorthStar ARM BCM53xx SoCs
to the upstream U-Boot. This is a back port on top of the
2023.04 version already imported to OpenWrt with the 5 necessary
upstream patches.
This is needed to create a small U-Boot for the BCM53xx-based
D-Link DIR-890L and I think also the DIR-885L, so that a
recent (bigger) kernel can be loaded and executed from the
SEAMA partitions on these devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.
Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree
Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
refuses to boot if it doesn't. The chosen "rootfs" volume must contain
a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
variable to the label mac. But "factoryparams" does not always
exist. Instead there is a "RIP" volume containing all the factory
data. Copying the "RIP" volume to "factoryparams" will fix this
Hardware
--------
SOC: MediaTek MT7986
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI: Mediatek MT7986 802.11ax 5 GHz
Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.2/24. Rename the image to C0A80101.img.
2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
console, Interrupt the autoboot process by pressing ESC when prompted.
3. Download and boot the OpenWrt initramfs image.
$ env set uboot_bootcount 0
$ env set firmware nominal
$ tftpboot
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
not configured by OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The vendor U-Boot implementaion on Telenor branded ZyXEL EX5700
devices does not store its environment on flash. It is instead
kept in a memory region. This is persistent over reboots, but
not over power cycling.
The dual partition failsafe system used by the vendor U-Boot
requires the OS to modify a variable in this memory environment.
This driver allows the ordinary uboot-envtools to access a
memory region like it was a partition on NOR flash.
The specific vendor U-Boot adds a "no-map" /reserved-memory
section and a top level /ubootenv node pointing to the memory
environment. The driver uses this device specific fact to
locate the region. The matching and probing code will likely
have to be adjusted for any other devices to be supported.
Example partial device tree:
/ {
..
ubootenv {
memory-region = <&uenv>;
compatible = "ubootenv";
};
..
reserved-memory {
..
uenv: ubootenv@7ffe8000 {
no-map;
reg = <0 0x7ffe8000 0 0x4000>;
};
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.
The majority of the code is based on @jewwest's PR #11830.
Specifications:
* CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
* Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
* Wi-Fi:
* 2.4 GHz: Qualcomm QCN5024 4x4
* 2x 5 GHz: Qualcomm QCN5054 4x4
* USB: 2x USB 3.0
* LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
* Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
* UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
* Power: 19 VDC, 3.1 A
Installation:
* Flashing OpenWrt is done in two steps:
a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
This writes an initramfs based OpenWrt image onto the RAX120v2
b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline
* U-Boot allows booting an initramfs image via TFTP:
- Set ip of your PC to 192.168.1.100
- At the serial console interrupt boot at "Hit any key to stop autoboot:"
- In u-boot run `tftpsrv`
- On your PC send the OpenWrt initramfs image:
tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb
Make 5G Aquantia phy work:
For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
u-boot by writing the firmware to the correct mtd partition.
The firmware file found in the Netgear stock firmware under /lib/firmware/ named
'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
be converted to a MBN file.
The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
under 'git_home/u-boot.git/tools/mkheader.py'
Convert the CLD file to MBN using:
$ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn
This MBN file can then be flashed to the MTD partition to be used by u-boot.
The necessary files can also be found in
https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware
* Write MBN file to MTD partition to be loaded automatically by u-boot:
U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
corresponds to `/dev/mtd25` in OpenWrt.
- find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)
$ fgrep -i 'ethphyfw' /proc/mtd
mtd25: 00080000 00020000 "ethphyfw
- copy mbn file to /tmp/ folder of the router
$ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/
- write mbn file to ethphyfw partition
$ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to RAX120v2 GPL source:
https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
9b2b203 fix usb_recv_tasklet -Wcast-function-type
a027da5 fix kernel 6.1 80211 link_id
7a9c802 fix build for kernel 6.1 prandom
3a3eb24 fix build for kernel 5.17 PDE_DATA
fe2afbd fix build for kernel 5.17 const netdev->dev_addr
7275bae fix build for 5.17 kernel complete_and_exit
c9c2aa7 Update usb_intf.c
revert the upstream 6.1 link_id (depend on kernel version) changes and
force 6.1 link_id
The downstream patch casting const off the direct dev_addr writes
triggers the runtime check from
Linux d07b26f5bbea ("dev_addr: add a modification check")
Fixes: #13261
Fixes: a07566ead8 ("rtl8812au-ct: fix even more compilation error with kernel 6.1")
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Commit e978072baaca ("Do prune_association only after the STA is
authorized") causes issues when an STA roams from one interface to
another interface on the same PHY. The mt7915 driver is not able to
handle this properly. While the commits fixes a DoS, there are other
devices and drivers with the same limitation, so revert to the orginal
behavior for now, until we have a better solution in place.
Fixes: #13156
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update to the latest stable version.
This update changes the default lockfile directory from /var/lock to
/run [1]. In OpenWRT we still use the "legacy" /var/lock and /run might
not even exist, so we add a patch to revert this particular change.
[1] aeb40f1166
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
This updates the Intel iwlwifi firmware for AX200 and AX210 from version
66 to version 72. Version 72 is the latest version supported by iwlwifi
from kernel 6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Instead of reading only a single 4kiB page, read the first 128kiB to
determine the size of an uImage.FIT using 'imsz' or 'imszb'.
This will be needed once we add more Device Tree Overlays, which may
happen for the BPi-R3 mini.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It cannot be properly cloned, since it is attached to the resource type.
Use a separate registry for data. Fixes object confusion issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
An active client mode interface could prevent the AP from claiming its channel
and mess up the bringup sequence order
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop obsolete control interface patches.
This fixes some corner cases in the previous code where the segment 0 center
frequency was not adjusted properly, leading to logspam and non-working AP
interfaces.
Additionally, shutting down the AP was broken, because the next beacon update
would re-enable it, leading to a race condition on assoc.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changes between 3.0.9 and 3.0.10 [1 Aug 2023]
* Fix excessive time spent checking DH q parameter value ([CVE-2023-3817])
* Fix DH_check() excessive time with over sized modulus ([CVE-2023-3446])
* Do not ignore empty associated data entries with AES-SIV ([CVE-2023-2975])
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Tear down all interfaces if the antenna settings change, so that the
capabilities can be recalculated properly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes this error: hostapd: nl80211: kernel reports: integer out of range
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check the phy before removing unrelated netdevs on the same hw device
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Package kernel module for Marvell 10G Ethernet PHYs found also in many
10G/1G/100M/10M RJ-45 SFP+ modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When building xdp-tools with CONFIG_USE_LLVM_HOST=y, on a host that
enabled stack protector by default in Clang, compilation fails with the
following error:
CLANG xdp-dispatcher.o
clang-16: error: ignoring '-fstack-protector-strong' option as it is not currently supported for target 'bpfeb' [-Werror,-Woption-ignored]
Add -fno-stack-protector to BPF_CFLAGS to fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Include AP ucode source file
Fixes: e56c5f7b27 ("hostapd: add ucode support, use ucode for the main ubus object")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ChangeLog:
46952ef trace-cmd: Version 3.2
f5871a1 libtracecmd: Version 1.4.0
d498af1 trace-cmd build: Add trace-attach.c to meson build
736df06 trace-cmd: Add initial support for meson
e183566 libtracecmd: Add initial support for meson
c508713 trace-cmd test: Quiet valgrind from reporting forked children
8ec026f trace-cmd test: Close handle after opening
4c179a6 trace-cmd library: Fix memory leaks of followers
aa21520 trace-cmd: Add Makefile target for memory test
925e15f trace-cmd and library: Update the version to the development
4fa31c0 trace-cmd attach: Add new command "attach"
7e721ef trace-cmd library: Add tracecmd_get_tsc2nsec() API
8908555 tracecmd library: Unlock records in tracecmd_iterate_events()
2668b13 trace-cmd agent: Add "IP" to -N argument in help message
22ad81e trace-cmd record: Remove redundant check of instance in allocate_instance()
d7ce897 libtracecmd: Free buf_from in error path of tracecmd_compress_copy_from()
6776d7a trace-cmd: Update v7 trace.dat documentation to clarify the strings section
9d6f3ba trace-cmd record/extract: Do not destroy existing instances
9c9d5ed trace-cmd extract: Do not extract top level unless told to
4b92132 libtracecmd: Fix tracecmd_compress_copy_from() write size return
f30abfd documentation: trace-cmd-report: Document filter scope
7a390c5 trace-cmd-report: Support global filters
04ad2c6 trace-cmd report: Ensure filter is applied to single input file
edf9424 trace-cmd: Open code execvp routine to avoid multiple execve syscalls
Signed-off-by: Nick Hainke <vincent@systemli.org>
ChangeLog:
aebab37 libtracefs: version 1.7
a3237c3 libtracefs: Add initial support for meson
b25019f libtarcefs doc: Add tracefs_kprobe_destroy() to index man page
4c2194f libtracefs doc: State that tracefs_dynevent_create() is needed for tracefs_kprobe_alloc()
df53d43 libtracefs Documentation: Add missing prototypes in top level man page
9a2df4a libtracefs: Update version to 1.7.dev
18ede68 libtracefs: Add tracefs_kprobe_destory() API
309b1ba libtracefs tests: Add helper function to destroy dynamic events
53dce80 tracefs: Add tracefs_time_conversion() API
5ea4128 libtracefs: Add tracefs_find_cid_pid() API
857dd3e libtracefs/utest: Fix crashing of synth test when synths exist
6332309 libtracefs/utest: Do not use synth for test_synth element
25cd206 libtracefs: Clarify the tracefs_synth_create() man page
6b6d43f libtracefs: Do not allow tracefs_synth_set_instance() on created synth
c860f93 libtracefs: Documentation for tracefs_synth_set_instance
0039173 libtracefs: New API to set synthetic event instance
e97c311 libtracefs: Do not segfault in tests if synthetic events are not configured
185019c libtracefs: Add tracefs_instance_tracers() API
6775d23 libtracefs: Do not use hwlat tracer and fdb_delete event for tests
5a1a01e libtracefs: Add stacktrace to tracefs_sql()
b1b234e libtracefs: Unit test for tracefs_instance_reset()
dd620f4 libtracefs: Documentation for tracefs_instance_reset()
789e82d libtracefs: New API to reset ftrace instance
Signed-off-by: Nick Hainke <vincent@systemli.org>
8c2758b4fbbb wireless: add support for replacing data blobs at runtime
0ff22a6a68ce wireless: enable dynamic reconfiguration by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This implements vastly improved dynamic configuration reload support.
It can handle configuration changes on individual wifi interfaces, as well
as adding/removing interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used to run a standalone EAP server that can be used from
other APs. It uses json as user database format and can automatically
handle reload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
Add patch to fix build failure caused by a missing header which had
previously been implicitely included.
Fixes: 6ddb5f5a65 ("uboot-mediatek: update to version 2023.07.02")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Among the patches adding support for MT7988 also came the switch to
use fdtdec_setup_mem_size_base() and no longer rely on CFG_SYS_SDRAM_BASE.
Take care of our downstream boards which did not have a 'memory' node in
their device trees.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of using the hash of the Github-generated tarball use the
hash of the tarball generated by the OpenWrt build system (in this
case they are different, unfortunately).
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: 07dbeb430e ("arm-trusted-firmware-mediatek: update to sources of 2023-07-24")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for the SKBPRIO queuing discipline. This is subtly
different than prio as it also drops packets from the lower priority
flows.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Fix more compilation error with kernel 6.1 and make it possible to
compile.
Multiple fix are done due to kernel bump:
- PDE_DATA (now deprecated) to pde_data
- dev_addr now const and require some cast
- prandom_u32 (now deprecated) to get_random_u32
Also other minor fix for always true condition and tasklet type cast not
compatible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Due to some hiccup my local urngd-2023-07-25-7aefb47b.tar.xz ended up
being different from archived one. Repackaging it locally confirmed the
previous hash was incorrect.
Fixes: c74b5e09e6 ("urngd: update to the latest master")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This patch makes some improvements to the MT7620 RF calibration.
1. Move MT7620 PA/LNA calibration code to dedicated functions.
2. Restore RF and BBP registers before R-Calibration.
3. Do Rx DCOC calibration again before RXIQ calibration.
4. Use SoC specific AGC initial LNA value.
5. Correct MAC_RX_EN mask in rt2800_r_calibration()[1].
[1] This change may fix the "BBP/RF register access failed" error:
ieee80211 phy0: rt2800_wait_bbp_rf_ready: Error - BBP/RF register access failed, aborting
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Import pending patches adding support for MT7988 and provide builds
for the reference board for all possible boot media.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Release 2023.07 got tagged wrongly and replaced by follow-up release
2023.07.02.
Now using upstream DTS for BPi-R3.
Removed two patches which made it upstream, refreshed the rest.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use updated Trusted Firmware-A sources from MediaTek, now stacked
on top of the ARM Trusted Firmware-A v2.9 release.
Add builds for the newly added MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since 2021.07 multiple bugs were introduced that made it impossible to
create a bootable target for mvebu. Those issues should be now fixed since
2023.07-rc1.
References: #11661
Signed-off-by: Oli Ze <olze@trustserv.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs
Signed-off-by: Petr Štetiar <ynezz@true.cz> [facelift]
Because this device enable NMBM by default, most users use custom
U-Boot with NMBM-Enabled in Chinese forums.
This layout is the same as the ubootmod layout but enabling NMBM.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
The existing implementation incorrectly reported `running` for services
without any instances or with all instances stopped/terminated.
Improve the default implementation of `/etc/init.d/* status` to properly
report services with not running instances. In case a service exists,
but without running instance, the status call will now report
"not running" with exit code 5. In case some instances are running and
some are stopped/terminated, the call will report "running (X/Y)" where
`X` denoted the amount of running instances and `Y` the amount of total
registered ones.
Ref: https://forum.openwrt.org/t/x/159443
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
8667347 build: allow passing SOVERSION value for dynamic library
Also adjust packaging of the library to only ship the SOVERSION
suffixed library object, to allow for concurrent installation of
ABI-incompible versions in the future.
Fixes: #13082
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
350b960 add support for multi GNSS solutions
fb87d0f ugps: add baud rate command line option
a8171a0 main.c: -S does not take any options
Build-tested: ramips/ltap-2hnd
Run-tested: ramips/ltap-2hnd
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
At least Fedora and RHEL 9 set RSAMinSize=2048, so when trying to use
failsafe, we get 'Bad server host key: Invalid key length'
To workaround the issue, we can use: ssh -o RSAMinSize=1024 ...
Generating 2048 bits RSA is extremely slow, so add ed25519.
We keep RSA 1024 to be as compatible as possible.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
53edfc7aaa34 wifi: mt76: mt7603: fix beacon interval after disabling a single vif
7ef4dd12d982 wifi: mt76: mt7603: fix tx filter/flush function
152608a40aa7 wifi: mt76: mt7615: do not advertise 5 GHz on first phy of MT7615D (DBDC)
cacac3902a63 wifi: mt76: split get_of_eeprom in subfunction
cd3dfe392769 wifi: mt76: add support for providing eeprom in nvmem cells
Signed-off-by: Felix Fietkau <nbd@nbd.name>
7aefb47 jitterentropy-rngd: update to the v1.2.0
What's interesting about jitterentropy-rngd v1.2.0 release is that it
bumps its copy of jitterentropy-library from v2.2.0 to the v3.0.0. That
bump includes a relevant commit 3130cd9 ("replace LSFR with SHA-3 256").
When initializing entropy jent calculates time delta. Time values are
obtained using clock_gettime() + CLOCK_REALTIME. There is no guarantee
from CLOCK_REALTIME of unique values and slow devices often return
duplicated ones.
A switch from jent_lfsr_time() to jent_hash_time() resulted in many less
cases of zero delta and avoids ECOARSETIME.
Long story short: on some system this fixes:
[ 6.722725] urngd: jent-rng init failed, err: 2
This is important change for BCM53573 which doesn't include hwrng and
seems to have arch_timer running at 36,8 Hz.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Kernel 6.1 have renamed complete_and_exit to kthread_complete_and_exit.
This was just a rename and nothing is changed implementation wise.
Fix compilation error by using the new symbol name.
Fix compilation error:
In file included from /builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/include/osdep_service.h:41,
from /builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:32,
from /builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c:22:
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c: In function 'rtw_cmd_thread':
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/include/osdep_service_linux.h:166:23: error: implicit declaration of function 'complete_and_exit' [-Werror=implicit-function-declaration]
166 | #define thread_exit() complete_and_exit(NULL, 0)
| ^~~~~~~~~~~~~~~~~
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c:706:9: note: in expansion of macro 'thread_exit'
706 | thread_exit();
| ^~~~~~~~~~~
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c:708:1: error: control reaches end of non-void function [-Werror=return-type]
708 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch adds basic TX power control for the MT7620 and limits its
maximum TX power. This can avoid the link speed decrease caused by
chip overheating.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hardware
--------
CPU: Mediatek MT7981
RAM: 512M DDR4
FLASH: 256M NAND
ETH: MaxLinear GPY211 (2.5GbE N Base-T)
WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN: 1x Reset
LED: 1x Multi-Color
UART Console
------------
Available below the rubber cover next to the ethernet port.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.
$ atnf nwa50axpro-openwrt-initramfs.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd9 get-status
$ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd9 set-active-image 0
Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.
$ sysupgrade -n image.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
ChangeLog:
125b080 Release version 6.4.
5660918 update UAPI header copies
f493e63 netlink: fix duplex setting
b3e341c cmis: report LOL / LOS / Tx Fault
045d8db sff-8636: report LOL / LOS / Tx Fault
a6505f3 drop checks for macros provided in UAPI header copies
86c0c41 do not check for strtol() function
dd8e3ae actually check for C11 compiler
43e4d30 add local copies of macros from autoconf-archive
faa4700 drop check for big endian types
31b7b5e Require a compiler with support for C11 features
946d18b update UAPI header copies
eebf01f ethtool: Add support for configuring tx-push-buf-len
2782ea8 update UAPI header copies
Signed-off-by: Nick Hainke <vincent@systemli.org>
The duplicate sections are caused by a race condition at boot, when board.json
is not available. In that case, the final phy name cannot be resolved, and extra
sections referring to the path are created.
Fix this by making sure that wifi config is not being run before board.json
is created.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is the first commit to introduce the base for the N821 board used
in Cisco vEdge 1000.
This commit does not include the custom CPLD drivers but rather
everything else that is already present in the upstream kernel.
This results in an image that boots, but e.g. the SFP ports are not
usable.
Hardware:
- CPU: Cavium Networks CN6130, 4 cores @ 1.0 GHz
- Flash:
- 16 MiB SPI NOR presented as 2x8 MiB for A/B boot recovery
- 8192 MiB eMMC
- RAM: 4096 MiB
- Ethernet 1Gbit ports: 1x
- Ethernet SFP ports: 8x
- USB ports: 2x 3.0 Type-A on front panel
- Serial: Two, one internal and one external
- JTAG: Yes
- LED count: 18x
- Button count: 1x
- GPIOs: 1x
- Power: 2x redundant DC 12V barrel plug
- Extra: Slot for SD card on front
See the OpenWrt wiki for more hardware details.
Installation:
- Flash squashfs to /dev/sda2 and put kernel on /dev/sda1.
- Update uboot's bootcmd environment variable to match.
Full installation guide will be added to OpenWrt wiki when sysupgrade
support is added.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Tommy Nevtelen <tommy@nevtelen.com>
Tested-by: Viktor Ekmark <viktor@ekmark.se>
Tested-by: Daniel Wennberg <github@networkninja.se>
colrm is already built, package just isn't generated.
colrm can be used to remove columns from file/stdin.
Use cases vary, personally I needed it because I build openwrt
natively - and wolfssl configure script wants either colrm, or cut
but busybox's cut isn't accepted.
Built: x86_64, latest git
Tested: x86_64, latest git
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
The side-effect and main motivation is to also drop the FIT structure size
limit because with multiple device tree overlays it may easily grow beyond
the previous 4kB limit in the future.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ASUS RT-AC59U / RT-AC59U v2 are wi-fi routers with a large number of
alternate names, including RT-AC1200GE, RT-AC1300G PLUS, RT-AC1500UHP,
RT-AC57U v2/v3, RT-AC58U v2/v3, and RT-ACRH12.
ASUS ZenWiFi AC Mini(CD6) is a mesh wifi system. The unit labeled CD6R
is the router, and CD6N is the node.
Hardware:
- SoC: QCN5502
- RAM: 128 MiB
- UART: 115200 baud (labeled on boards)
- Wireless:
- 2.4GHz: QCN5502 on-chip 4x4 802.11b/g/n
currently unsupported due to missing support for QCN550x in ath9k
- 5GHz: QCA9888 pcie 5GHz 2x2 802.11a/n/ac
- Flash: SPI NOR
- RT-AC59U / CD6N: 16 MiB
- RT-AC59U v2 / CD6R: 32 MiB
- Ethernet: gigabit
- RT-AC59U / RT-AC59U v2: 4x LAN 1x WAN
- CD6R: 3x LAN 1x WAN
- CD6N: 2x LAN
- USB:
- RT-AC59U / RT-AC59U v2: 1 port USB 2.0
- CD6R / CD6N: none
WiFi calibration data contains valid MAC addresses.
The initramfs image is uncompressed because I was unable to boot a
compressed initramfs from memory (gzip or lzma). Booting a compressed
image from flash works fine.
Installation:
To install without opening the case:
- Set your computer IP address to 192.168.1.10/24
- Power up with the Reset button pressed
- Release the Reset button after about 5 seconds or until you see the
power LED blinking slowly
- Upload OpenWRT factory image via TFTP client to 192.168.1.1
Revert to stock firmware using the same TFTP method.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Safely detect integer overflow in try_addint() and try_subint().
Old code relied on undefined behavior, and recent versions of GCC on x86
optimized away the if-statements.
This caused integer overflow in Lua code instead of falling back to
floating-point numbers.
Signed-off-by: Adam Bailey <aebailey@gmail.com>
commit c0611b45a9 ("e2fsprogs: symlink e2fsck to fsck.ext{2, 3, 4},
and tune2fs to findfs") introduced a symlink from tune2fs to findfs.
This only works when the included private libblkid library is used, but
commit 5b1660a538 ("utils/e2fsprogs: Update to 1.43.6") disabled the
usage of this private lib and enabled the shared lib support.
Removing this symlink makes it possible to install tune2fs and findfs
package.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
The return value of the .remove function pointer has changed from
int to void with Linux 5.18. Use a precompiler macro to allow building
the leds-ws2812b module with both, Linux 5.15 and Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the i.MX Pixel Pipeline IP block
which is available on some imx6 flavours [1]
This allows to use hardware offloading for operations like:
- Colour conversion
- Scaling
- Rotation
[1] https://en.wikipedia.org/wiki/I.MX#i.MX_6_series
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
This adds support for the Video Processing Unit IP block
which is present in certain i.MX SOC's.
The vpu used in imx6 is the coda960 which supports:
- h264 enc
- h264 dec
- jpeg enc
- jpeg dec
Please note that the required firmware needs to be added
by yourself as it's not available currently in linux-firmware upstream.
The firmware package can be found on the internet
and it will decompress itself exposing all binaries
after accepting the EULA.
The binaries should be placed at exactly these paths:
- /lib/firmware/vpu_fw_imx6d.bin
- /lib/firmware/vpu_fw_imx6q.bin
Following output will be printed at boottime if all is well:
[ 9.769638] coda 2040000.vpu: Firmware code revision: 46076
[ 9.775277] coda 2040000.vpu: Initialized CODA960.
[ 9.780082] coda 2040000.vpu: Firmware version: 3.1.1
[ 9.785312] coda 2040000.vpu: coda-jpeg-encoder registered as video0
[ 9.791859] coda 2040000.vpu: coda-jpeg-decoder registered as video1
[ 9.798375] coda 2040000.vpu: coda-video-encoder registered as video2
[ 9.805013] coda 2040000.vpu: coda-video-decoder registered as video3
gstreamer will automatically detect and use all encoders/decoders.
Please note that a FILES catch-all is required for the videobuf-dma objects
as some modules enabling this could require (and thus generating) only 1 of them.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
This adds support for videobuf2-dma driver.
This module contains following flavors:
- Contiguous
- Scatter/Gather
Drivers using this can enable 1 of the, or both, depending on their needs.
Due to this, a FILES catch-all is required for the videobuf-dma objects
as depending on requirements, only 1 of them could get generated.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
This allows addition of devices which use these kernel
modules.
This also adds a package for handling dma within video2buf.
These are only build when selected by a caller
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
All patches automatically rebased.
Acknowledgment to @john-tho for the changes to fs.mk to accommodate new paths
introduced in 29429a1f58
Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
This patch will only force mac80211 loss detection upon ath10k by
masking the driver-specific loss-detection bit.
Ref: commit ed816f6ba8 ("mac80211: always use mac80211 loss detection")
Signed-off-by: David Bauer <mail@david-bauer.net>
The upstream board-2.bin file in the linux-firmware.git
repository for the QCA4019 contains a packed board-2.bin
for this device for both 2.4G and 5G wifis. This isn't
something that the ath10k driver supports.
Until this feature either gets implemented - which is
very unlikely -, or the upstream boardfile is mended
(both, the original submitter and ath10k-firmware
custodian have been notified). OpenWrt will go back
and use its own bespoke boardfile. This unfortunately
means that 2.4G and on some revisions the 5G WiFi is
not available in the initramfs image for this device.
Fixes: #12886
Reported-by: Christian Heuff <christian@heuff.at>
Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit adds support for following wireless routers:
- Beeline SmartBox PRO (Serсomm S1500 AWI)
- WiFire S1500.NBN (Serсomm S1500 BUC)
This commit is based on this PR:
- Link: https://github.com/openwrt/openwrt/pull/4770
- Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.
My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1
Common specification
--------------------
SoC: MediaTek MT7621AT (880 MHz, 2 cores)
Switch: MediaTek MT7530 (via SoC MT7621AT)
Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe: via J2 on PCB, not soldered on the board
UART: J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek
Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1
WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1
MAC address table (PRO)
-----------------------
use address source
LAN *:23 factory 0x1000 (label)
WAN *:24 factory $label +1
2g *:23 factory $label
5g *:25 factory $label +2
MAC addresses (NBN)
-------------------
use address source
LAN *:0e factory 0x1000
WAN *:0f LAN +1 (label)
2g *:0f LAN +1
5g *:10 LAN +2
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
a. OpenWrt - that's OK, the mission accomplished
b. Stock firmware - install Stock firmware (to switch booflag from
Sercomm0 to Sercomm1) and then OpenWrt factory image.
Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
reboot
2. Install stock firmware via the web OEM firmware interface
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.
Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).
It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.
Related: https://github.com/openwrt/openwrt/pull/5084
For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.
Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
boot, then hold the reset button for 10 seconds. This is needed
because sysupgrade in the stock firmware will attempt to preserve its
configuration using sysupgrade.tgz.
See https://github.com/openwrt/openwrt/pull/4182
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.
Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
All LEDs and buttons appear to work without state_default.
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz
* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
DTS file for this device.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
In the recent NSS-DP update FDB roaming fix we had was removed as in
testing no issue were reported, but after it was merged the old duplicate
MAC issue reappeared so lets port the previous FDB fix to work with newer
NSS-DP.
Fixes: 4ee444b5da ("kernel: qca-nss-dp: update to 12.4.5.r1")
Signed-off-by: Robert Marko <robimarko@gmail.com>
d1f07cf devices: add device id for Atheros AR9287 and AR9380
65ea345 nl80211: constify a few arrays
ca79f64 lib: report byte counters as 64 bit values
This contains an ABI change, increase the ABI version too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When using an Intel AX210 card, the Bluetooth hci interface failed
to start due to a missing "ibt-0041-0041.sfi" file.
Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-0041-0041.sfi (-2)
A device specific configuration file (DDC) is also required:
Bluetooth: hci0: Found device firmware: intel/ibt-0041-0041.sfi
Bluetooth: hci0: Waiting for firmware download to complete
...
Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0041-0041.ddc
Bluetooth: hci0: Applying Intel DDC parameters completed
Bluetooth: hci0: Firmware timestamp 2023.13 buildtype 1 build 62562
Fixes: #8558
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Migrate to "new" image generation method. Device profiles will be generated
based on image/Makefile instead of profiles/ , which will also allow to
automatically build images for all supported devices via buildbot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
493e1589bc8b bridge: fix coverity false positive report
03a619947717 bridge: add support for configuring extra vlans for the bridge itself
4bea6d21a9ab wireless: fix changing reconf/serialize options in configuration
255b4d5c472e wireless: fix handling config reload with reconf=1
1ab992a74b43 wireless: fix another reconf issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Qualcomm has finally started the preparatory work in order to support
kernel 6.1, so lets make use of that and update NSS-DP 12.4.5.r1 which
allows us to drop almost some of the patches.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm has finally started the preparatory work in order to support
kernel 6.1, so lets make use of that and update SSDK 12.4.5.r1 which
allows us to drop almost all of the patches.
Lets also install the forgotten SSDK netlink header.
Signed-off-by: Robert Marko <robimarko@gmail.com>
rk3399 ATF requires arm toolchain to build the m0 pmu driver.
As OpenWrt doesn't ship this toolchain so download the prebuilt one
just like what we did in arm-trusted-firmware-mvebu.
Fixes: 5d1cb52da0 ("arm-trusted-firmware-rockchip: Update to 2.9")
Reported-by: Wurzer Juergen <wurzer.juergen@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
General specification:
SoC Type: MediaTek MT7620A (580MHz)
ROM: 8 MB SPI-NOR (MX25L6406E)
RAM: 64 MB DDR (W9751G6KB-25)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Wireless: 5 GHz (MediaTek MT7610EN): ac/n
Buttons: 2 button (POWER, WPS/RESET)
Bootloader: U-Boot 1.1.3
Power: 12 VDC, 0.5 A
MACs:
| LAN | [Factory + 0x04] - 2 |
| WLAN 2.4g | [Factory + 0x04] - 1 |
| WLAN 5g | [Factory + 0x8004] - 3 |
| WAN | [Factory + 0x04] - 2 |
OEM easy installation:
1. Use a PC to browse to http://192.168.0.1.
2. Go to the System section and open the Firmware Update section.
3. Under the Local Update at the right, click on the CHOOSE FILE...
4. When a modal window appears, choose the firmware file and click on
the Open.
5. Next click on the UPDATE FIRMWARE button and upload the firmware image.
Wait for the router to flash and reboot.
OEM installation using the TFTP method (need level converter):
1. Download the latest firmware image.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware
image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect the PC
to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address 192.168.0.180
and subnet mask 255.255.255.0.
5. Connect serial port (57600 8N1) and turn on the router.
6. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load
system code then write to Flash via TFTP.").
7. Press Y key when show "Warning!! Erase Linux in Flash then burn new
one. Are you sure? (Y/N)"
Input device IP (192.168.0.1) ==:192.168.0.1
Input server IP (192.168.0.180) ==:192.168.0.180
Input Linux Kernel filename () ==:firmware_name
The router should download the firmware via TFTP and complete flashing in
a few minutes.
After flashing is complete, use the PC to browse to http://192.168.1.1 or
ssh to proceed with the configuration.
Signed-off-by: Alexey Bartenev <41exey@proton.me>
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.
See the online manual for more information, including the
flash layout[2].
This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.
We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
The ZTE MF287+ is a LTE router used (exclusively?) by the network operator
"3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only
difference is the LTE modem)
Specifications
==============
SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287)
WiFi: 802.11a/b/g/n/ac SoC-integrated
MAC addresses
=============
LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1
Installation
============
Option 1 - TFTP
---------------
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x82000000 openwrt.bin
bootm 0x82000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:
ubiattach -m14
cat /dev/ubi0_0 > /tmp/ubi0_0
cat /dev/ubi0_1 > /tmp/ubi0_1
Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.
Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N kernel
Option 2 - From stock firmware
------------------------------
The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.
The exploit will be available at the device wiki page.
Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".
ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".
Complete commands:
cd /tmp
tftp -g -r factory.bin 192.168.0.22
cat /proc/driver/sensor_id
flash_erase /dev/mtd13 0 0
dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072
Afterwards, reboot your device and you should have a working OpenWrt
installation.
Restore Stock
=============
Option 1 - via UART
-------------------
Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.
Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.
ubiattach -m 14
ubirmvol /dev/ubi0 -N kernel
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N rootfs_data
ubimkvol /dev/ubi0 -N kernel -s $kernel_length
ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1
Option 2 - from within OpenWrt
------------------------------
This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.
Follow the commands from Option 1 to flash back to stock.
LTE Modem
=========
The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.
Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Device specifications:
======================
* Qualcomm/Atheros AR9344
* 128 MB of RAM
* 16 MB of SPI NOR flash
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4/5 GHz Wi-Fi
* 4x GPIO-LEDs (1x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* 2x fast ethernet
- lan1
+ builtin switch port 1
+ used as WAN interface
- lan2
+ builtin switch port 2
+ used as LAN interface
* 9-30V DC
* external antennas
Flashing instructions:
======================
Log in to https://192.168.127.253/
Username: admin
Password: moxa
Open Maintenance > Firmware Upgrade and install the factory image.
Serial console access:
======================
Connect a RS232-USB converter to the maintenance port.
Pinout: (reset button left) [GND] [NC] [RX] [TX]
Firmware Recovery:
==================
When the WLAN and SYS LEDs are flashing, the device is in recovery mode.
Serial console access is required to proceed with recovery.
Download the original image from MOXA and rename it to 'awk-1137c.rom'.
Set up a TFTP server at 192.168.127.1 and connect to a lan port.
Follow the instructions on the serial console to start the recovery.
Signed-off-by: Maximilian Martin <mm@simonwunderlich.de>
This commit adds support for Mercusys MR90X(EU) v1 router.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled
LEDs on ethernet ports
Button: 1 (Reset)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
The R3 (TX line) and R6 (RX line) are absent on the PCB. You should
solder them or solder the jumpers.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Once inside OpenWrt, set / update env variables:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial@11002000
fw_setenv stdin serial@11002000
fw_setenv stdout serial@11002000
fw_setenv tp_boot_idx 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Installation (without UART)
---------------------------
1. Login as root via SSH (router IP, port 20001, password - your web
interface password)
2. Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and
SSH settings from the p.1)
3. Add a newline after "#!/bin/sh":
telnetd -l /bin/login.sh
4. Save "65-iptv" file
5. Toggle "IPTV/VLAN Enable" checkbox in the router web interface and
save
6. Make sure that telnetd is running:
netstat -ltunp | grep 23
7. Login via telnet to router IP, port 23 (no username and password are
required)
8 Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the
router (e.g., using WinSCP and SSH settings from the p.1)
9. Stock busybox doesn't contain ubiupdatevol command. Hence, we need to
download and upload the full version of busybox to the router. For
example, from here:
https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64
Upload busybox-arm64 to the /tmp dir of the router and run:
in the telnet shell:
cd /tmp
chmod a+x busybox-arm64
10. Check "initramfs-kernel.bin" size:
du -h initramfs-kernel.bin
11. Delete old and create new "kernel" volume with appropriate size
(greater than "initramfs-kernel.bin" size):
ubirmvol /dev/ubi0 -N kernel
ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB
12. Write OpenWrt "initramfs-kernel.bin" to the flash:
./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin
13. u-boot-env can be empty so lets create it (or overwrite it if it
already exists) with the necessary values:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial@11002000
fw_setenv stdin serial@11002000
fw_setenv stdout serial@11002000
fw_setenv tp_boot_idx 0
14. Reboot to OpenWrt initramfs:
reboot
15. Login as root via SSH (IP 192.168.1.1, port 22)
16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
17. Run sysupgrade:
sysupgrade -n /tmp/sysupgrade.bin
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery (UART)
---------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Do what you need (restore partitions from a backup, install OpenWrt
etc.)
Stock layout
------------
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format
----------------
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 00:eb:xx:xx:xx:be | label |
| LAN | 00:eb:xx:xx:xx:be | label |
| WAN | 00:eb:xx:xx:xx:bf | label+1 |
| WLAN 2g | 00:eb:xx:xx:xx:be | label |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac". OEM wireless eeprom is also there (file
"MT7986_EEPROM.bin").
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
5211264 odhcpd: add support for dhcpv6_pd_min_len parameter
c6bff6f router: Add PREF64 (RFC 8781) support
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix a typo where the wrong KCONFIG was used and fix selecting the
correct kernel config option to use these packages.
Fixes: 4f443c885d ("netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxy")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
1571e18e4a69 bridge: add support for configuring extra tagged vlans on member devices
b719f189f243 bridge: make hotplug-added vlans default to tagged
edf3aced9f9a bridge: add support for adding vlan ranges via hotplug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ath10k does not report excessive loss in case of broken block-ack
sessions. The loss is communicated to the host-os, but ath10k does not
trigger a low-ack events by itself.
The mac80211 framework for loss detection however detects this
circumstance well in case of ath10k. So use it regardless of ath10k's
own loss detection mechanism.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
========
CPU Qualcomm Atheros QCA9558
RAM 256MB DDR2
FLASH 2x 16M SPI-NOR (Macronix MX25L12805D)
WIFI Qualcomm Atheros QCA9558
Atheros AR9590
Installation
============
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x80060000 ap115.bin; go 0x80060000"
$ setenv fb_openwrt "bank 1;
cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000"
$ setenv bootcmd "run fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
077e05f2b129 vlan/vlandev: pass through extra vlan information passed via hotplug
40fad91eb5be wireless: add network_vlan config attribute
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware
--------
SOC: MediaTek MT7986
RAM: 1024MB DDR3
FLASH: 128MB SPI-NAND (Winbond)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the WAX220. Conect to the serial console,
interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.2.1
$ setenv serverip 192.168.2.2
$ tftpboot openwrt.bin
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Now that qualcommax exists as a target and dependencies have been updated
let move ipq807x support to subtarget of qualcommax.
This is mostly copy/paste with the exception of having to update SSDK and
NSS-DP to use CONFIG_TARGET_SUBTARGET.
This is a preparation for later addition of IPQ60xx and IPQ50xx support.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s.
However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s
and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid
duplicating kernel patches and everything lets make a common target with
per SoC subtargets.
Start doing that by renaming ipq807x to qualcommax so that dependencies
on ipq807x target can be updated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add an UCI option to enable Multiple BSSID Advertisement. Enabling this
will announce all BSSIDS on a phy in a single beacon frame. The
interface that is brought up first will be the transmitting profile, all
others are non-transmitting profiles and will be advertised in the
Multiple BSSID element in Beacon and Probe Response frames of the first
interface.
This depends on driver and client support. Enabling this will result in
all but the first interface not being visible at all for clients that do
not support it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Some Broadcom MIPS devices require JFFS2 cleanmarkers to be present on the
kernel partition or the bootloader will identify the partition as corrupt and
won't boot the kernel.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
openssl sets additional cflags in its configuration script. We need to
make it aware of our custom cflags to avoid adding conflicting cflags.
Fixes: #12866
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
Backport patches improving ppp interface creation. As a side effect this
also fix a bug from using netdev trigger that suffer from LED state
wrongly set due to using old ioctl for ppp creation.
Tested-by: Csaba Sipos <metro4@freemail.hu>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If dual-stack configuration is in use, and dhcpv6 option is set, do not start
464xlat sub-interface for dhcpv6 sub-interace , as the configuration already
provides IPv4 connectivty, be it through single or dual APN configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add two new "v6apn" and "v6profile" properties, to support split-APN
dual-stack onfiguration. This extends the existing ipv4v6 PDP type,
allowing simultaneous connection to two distinct APNs,
one for IPv4 and one for IPv6.
The parameters override existing 'apn' and 'profile' respectively,
if set, but only for IPv6 part of the connection.
If unset, they default to their original values, constituting a standard
IPv4v6 setup.
If a different APN is set for IPv6, a corresponding profile MUST also be
configured, with a different ID, than the IPv4 profile, for example,
profile 2.
Both APNs must match ones configured through QMI or through 'AT+CGDCONT'
command.
Example configuration in UCI:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option autoconnect '1'
option pdptype 'ipv4v6'
option apn 'internet'
option v6apn 'internetipv6'
option profile '1'
option v6profile '2'
Corresponding profile configuration:
AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV6","internetipv6","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The cli is a one-time run, and memory leaks would have been irrelevant. But people call libsw with cli programs as samples.
Doing a good job of memory management calls means that people who call libsw are not so easy to make mistakes.
Signed-off-by: nichel Chen <nichelnich@gmail.com>
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
The armvirt target has been renamed to armsr (Arm SystemReady),
so the GRUB configuration also needs to change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Contains following updates:
* ipq8074: update RegDB in new submitted BDF
* Revert "ipq8074: update RegDB in new submitted BDF"
* qcn9074: update RegDB in new submitted BDF
* ipq8074: update RegDB in new submitted BDF
* qca-wireless: ipq40xx: add BDFs for ZTE MF287+
* Add BDFs for prpl Foundation Haze board
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There is no need for SSDK to support 5.15 anymore since the only user and
possible future ones are on 6.1.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit add u-boot env config for GL-MT3000, so
that we can use fw_printenv to print u-boot env and
use fw_setenv to set u-boot env in GL-MT3000.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
CVE-2023-2650 fix
Remove upstreamed patches
Major changes between OpenSSL 3.0.8 and OpenSSL 3.0.9 [30 May 2023]
* Mitigate for very slow OBJ_obj2txt() performance with gigantic OBJECT IDENTIFIER sub-identities. (CVE-2023-2650)
* Fixed buffer overread in AES-XTS decryption on ARM 64 bit platforms (CVE-2023-1255)
* Fixed documentation of X509_VERIFY_PARAM_add0_policy() (CVE-2023-0466)
* Fixed handling of invalid certificate policies in leaf certificates (CVE-2023-0465)
* Limited the number of nodes created in a policy tree (CVE-2023-0464)
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
One is never to write to dev->addr directly. In 6.1 it will be a const and
with the newly enabled WERROR, we get a failing grade.
Lets fix this ahead of time.
Ref: adeef3e321
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Update bootloader environment for BPi-R3 and BPi-R64 to adapt to new
device tree overlay mechanism now that support for multiple device
tree overlays has been added.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 5d2de00555.
I received multiple reports that in various configurations this FW version
is not stable and crashes, so lets revert to 01385 revision which works.
Fixes#12815
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixes tag]
Currently kernel crashes when of_phy_connect has issues:
Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000308
...
pc : phy_attached_print+0x28/0x1b0
lr : phy_attached_info+0x14/0x20
...
Call trace:
phy_attached_print+0x28/0x1b0
phy_attached_info+0x14/0x20
nss_dp_adjust_link+0x544/0x6c4 [qca_nss_dp]
of_phy_connect returns either pointer or NULL, so can't be checked with
IS_ERR macro.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
b09b316aeaf6 blobmsg: add blobmsg_parse_attr function
eac92a4d5d82 blobmsg: add blobmsg_parse_array_attr
ef5e8e38bd38 usock: fix poll return code check
6fc29d1c4292 jshn.sh: Add pretty-printing to json_dump
5893cf78da40 blobmsg: Don't do at run-time what can be done at compile-time
362951a2d96e uloop: fix uloop_run_timeout
75a3b870cace uloop: add support for integrating with a different event loop
Signed-off-by: Felix Fietkau <nbd@nbd.name>
412d03012f13 network: prevent adding endpoint routes for addresses on the network
faaf9cee6ef4 utils: fix ipv4 checksum issue
0e1c2fad3540 pex-msg: fix memory leak on fread fail in pex_msg_update_request_init
51be0ed659d0 host: fix crash parsing gateway when no endpoint is specified
ca17601dc24e wg-linux: add support for splitting netlink messages for allowed ips
7d3986b7a5a2 wg-linux: increase default messages size
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Synchronize the ath11k backports with the current ath-next tree.
This introduces support for MBSSID and EMA, adds factory test mode and
some new HTT stats.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport EMA beacon support from kernel 6.4.
It is required for MBSSID/EMA suport in ath11k that will follow.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
QCA released a point update for the 2.9.0.1 firmware, so lets update to it.
Runtime tested on Dynalink DL-WRX36.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Built-in engine configs are added in libopenssl-conf/install stage
already, postinst/add_engine_config is just duplicating them, and
due to the lack of `config` header it results a broken uci config:
> uci: Parse error (invalid command) at line 3, byte 0
```
config engine 'devcrypto'
option enabled '1'
engine 'devcrypto'
option enabled '1'
option builtin '1'
```
Add `builtin` option in libopenssl-conf/install stage and remove
duplicate engine configuration in postinst/add_engine_config to
fix this issue.
Fixes: 0b70d55a64 ("openssl: make UCI config aware of built-in engines")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Release Notes:
https://valgrind.org/docs/manual/dist.news.html
This improves support for the memory allocator used in musl libc 1.2.2
and later which is currently used by OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Build and package kernel self-tests used for BPF testing, program and JIT
development. This package, together with the existing 'kmod-bpf-test', was
extensively used for past upstream Linux JIT submissions [1].
Currently this includes only 'test_verifier'; building 'test_progs' will
fail due to known endian limitations with bpftool skeletons.
[1]:https://lore.kernel.org/bpf/cover.1633392335.git.Tony.Ambardar@gmail.com
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Set net.core.bpf_jit_kallsyms=1 in /etc/sysctl.d/10-default.conf.
For privileged users, this exports addresses of JIT-compiled programs to
appear in /proc/kallsyms when present, allowing their use for debugging
and in traces.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The Amazon ENA network devices are also used on the
AWS Arm (Graviton) instance types, so move it from
the x86-only module file to the top level netdevices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The MDIO bus multiplexing framework is used by some drivers
such as dwmac-sun8i.
As this is a per-driver requirement, set it to be hidden in the menu.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This adds a separate package for EFI on Arm SystemReady
compatible machines. 32-bit Arm UEFI is supported as well.
It is very similar to x86-64 EFI setup, without the
need for BIOS backward compatibility and slightly
different default modules.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
When using the Gemini, we apply patches that create a single
module that support both host and device mode these days.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(move module to gemini target, keep both 6.1+2-ish + 5.15 module
CONFIG and files around until 5.15 is dropped)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add support for the Xunlong Orange Pi R1 Plus LTS.
Manually generated of-platdata files to avoid swig dependency.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Add support for the Xunlong Orange Pi R1 Plus.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The smsc95xx driver got selftest support with kernel 5.18, add the new
dependency fixing the all kernel modules build on MIPS malta with kernel
6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_PHYLINK Kconfig option in the kernel selects CONFIG_LIBPHY.
Add this dependency to fix the all kernel modules build on MIPS malta
and armvirt with kernel 6.1.
With kernel 5.15 mod-phylink and kmod-sfp are empty packages because
no OpenWrt kmod is selecting a module which needs sfp or phylink
support.
Fixes: #12758
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Contains following changes:
* bridge: bridge_dump_info: add dumping of bridge attributes
* bridge: make it more clear why the config was applied
* cmake: fix build by reordering the cflags definitions
* treewide: fix multiple compiler warnings
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's required by bcm53xx. This allows dropping separated oseama package
and avoids some code duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Some of firmware utils may be required on target devices. It's useful
e.g. for dealing with some firmware formats. That is often required
(supporting specific format) to provide an option to revert to original
firmware.
So far we had packaged "otrx" util only for use on Broadcom targets.
Refactor that to package the whole firmware-utils project so we can
package any single util needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
At this moment loadaddr in most layerscape boards are configured to
0x81000000. 5.15 kernel on some boards is bigger than 5.10 and it cause error:
Loading kernel from FIT Image at 81000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.112
Created: 2023-05-21 17:39:35 UTC
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x810000ec
Data Size: 7513944 Bytes = 7.2 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x80000000
Entry Point: 0x80000000
Hash algo: crc32
Hash value: 6fd69550
Hash algo: sha1
Hash value: ee34c753ffb615e199a428762824ad4a0aaef90a
Verifying Hash Integrity ... crc32+ sha1+ OK
Loading fdt from FIT Image at 81000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt fsl_ls1088a-rdb-sdboot device tree blob
Created: 2023-05-21 17:39:35 UTC
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8172a98c
Data Size: 19794 Bytes = 19.3 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 59792ba3
Hash algo: sha1
Hash value: 135585a49f86cd85acea559b78b0098ae99d5e12
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8172a98c
Uncompressing Kernel Image
ERROR: new format image overwritten - must RESET the board to recover
resetting ...
This patch changes loadaddr to 0x88000000 (like LS1012A-FRDM board) to
avoid overlapping for bigger images (like initramfs) too.
Tested-by: Alexandra Alth <alexandra@alth.de> [LS1088ARDB]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Add kernel 6.1 support to SSDK, it was just a case of adding the kernel
version identification and fixing up get_random_u32.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This was needed when we had 5.10 kernel as well, but now that all
targets are running 5.15 or 6.1 we can safely drop it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
ath10k-ct now offers 6.2 and 6.4 versions, so lets update to use 6.2
so we can get rid of the API update patch as well as NVMEM as that is
already present in the newer driver.
Ben merged the debug compilation patch so we can remove that one as well.
Update patches to point to 6.2 version and refresh them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add new package for building bootloader for the SiFive U-series boards. Supported
boards at this stage are the HiFive Unleashed and HiFive Unmatched.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
OpenSBI is a form of a first-stage bootloader, which initializes
certain parts of an SoC and then passes on control to the second
stage bootloader i.e. an u-boot image.
We're introducing the package with release v1.2, which provides
SBI v0.3 and the SBI SRST extensions which helps to gracefully
reboot/shutdown various HiFive-U SoCs.
Tested on SiFive Unleashed and Unmatched boards.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
From commit dc0e6056de ("rxrpc: Fix missing dependency on NET_UDP_TUNNEL")
upstream, kmod-rxrpc uses functions enabled by CONFIG_NET_UDP_TUNNEL.
Add package dependencies on kmod-udptunnel4 and kmod-udptunnel6 to avoid
build errors like:
Package kmod-rxrpc is missing dependencies for the following libraries:
ip6_udp_tunnel.ko
udp_tunnel.ko
This change applies to both kernels 5.15 and 6.1.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add new build option BOARD_QFN/BOARD_BGA.
This option is only useful for MT7981 device.
MT7981A/B: BOARD_BGA, MT7981C: BOARD_QFN.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Add reserved memory for pstore/ramoops to device tree used by Linux
as well as U-Boot.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Compex WPQ873 is a development board with two M.2 B-key
slots for cellular modems.
Device info:
- IPQ8072A SoC
- 512MiB RAM
- 256MiB NAND flash
- 8MiB SPI NOR
- 3x 1GigE ports
- 1x 2.5GigE port
- 2.4GHz/5GHz AX WLAN
- 1x USB 3.0 port
- 1x M.2 B-key socket with PCIe 3.0
- 1x M.2 B-key socket with PCIe 2.0 and USB 3.0
- 4x SIM card slots
- Bluetooth LE 5.0 (QCA4024)
Prerequisites
1) TFTP server
2) 3.3V USB to TTL cable for UART console
2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it
TTL connector pinout: 2=TX, 3=RX, 4=GND
Arrow marks pin 1 which is 3.3V
Serial port settings: 115200 8N1 no flow control
The device will most likely ship with a QSDK-based firmware.
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server, for example:
`setenv serverip 192.168.1.10`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Afterwards, you can use sysupgrade to flash new OpenWRT images.
Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
My original bpftools package made "variant" builds of bpftool and libbpf
as a convenience, since both used the same local kernel sources with the
same versioning. This is no longer the case, since the commit below
switched to using an out-of-tree build mirror hosting repos for each.
Replace bpftools with separate bpftool and libbpf packages, each simplified
and correctly versioned. Also fix the broken libbpf ABI introduced in the
same commit. Existing build .config files are not impacted.
Fixes: 00cbf6f6ab ("bpftools: update to standalone bpftools + libbpf, use the latest version")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
It's only used on devices in mt7621 and mt7622 subtargets, so no reason
to compile it for others.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
As of ed5c2f5fd10d ("i2c: Make remove callback return void") return
value of remove function is ignored.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Currently, SSDK is rather special in the sense that its not being built as
a proper out of tree module at all but rather like a userspace application
and that involves a lot of make magic which unfortunately broke with make
version 4.4 and newer.
Luckily QCA finally added a way to build SSDK as an out of tree module
and it uses the kernel buildsystem which makes it compile with make 4.4
as well.
So lets backport the support for it and switch to using it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel 6.1 now has fortify_memcpy_chk() and it is causing the following
warning while trying to compile backports:
CC [M] /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/net/wireless/util.o
In file included from ./include/linux/string.h:253,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/string.h:3,
from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./include/linux/smp.h:13,
from ./arch/arm64/include/asm/arch_timer.h:18,
from ./arch/arm64/include/asm/timex.h:8,
from ./include/linux/timex.h:67,
from ./include/linux/time32.h:13,
from ./include/linux/time.h:60,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/time.h:3,
from ./include/linux/skbuff.h:15,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/backport-include/linux/etherdevice.h:3,
from /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/net/wireless/util.c:12:
In function 'fortify_memcpy_chk',
inlined from 'ieee80211_strip_8023_mesh_hdr' at /home/robimarko/Building/AX3600/ipq807x-5.15/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/backports-6.1.24/net/wireless/util.c:590:3:
./include/linux/fortify-string.h:404:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
404 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
This issue was fixed in the final version of
("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces") that was
merged upstream but we have a older version that is using:
memcpy(&payload.eth.h_dest, mesh_addr, 2 * ETH_ALEN);
instead of:
memcpy(&payload.eth, mesh_addr, 2 * ETH_ALEN);
So, lets just backport the merged version of patch to fix the issue.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adapt filesystem kmods for building under kernel 6.1:
* Depend on kernel not being 5.10 rather than only 5.15
* kmod-fs-9p depends on kmod-fs-netfs from 5.17 as they started using
netfs helpers
* Set new KConfig options to N
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update the WWAN kmods for compilation under kernel 6.1:
* Depend on kernel not being 5.10 rather than only 5.15
* Enable CONFIG_WWAN_DEBUGFS as its now optional from 5.17
* Add missing symbols for new WWAN drivers to generic config
Signed-off-by: Robert Marko <robimarko@gmail.com>
Release Notes:
http://lists.busybox.net/pipermail/busybox-cvs/2023-May/041510.html
Refresh commands, run after busybox is first built once (nothing changed
compared to 1.36.0):
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-mipsel_24kc_musl/busybox-default/busybox-1.36.1
cd ..
./convert_defaults.pl ../../../build_dir/target-mipsel_24kc_musl/busybox-default/busybox-1.36.1/.config > Config-defaults.in
Manual edits needed afterward:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* Config-defaults.in: correct the default ports that get reset
BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT 80
BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT 23
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit a few Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The x86_64 UML target wants to include SSSE3 optimized
crypto code which lives under /arch/x86/crypto.
However, these are not built and this causes an error.
| ERROR: module '[...]/arch/x86/crypto/sha512-ssse3.ko' is missing.
| make[3]: *** [modules/crypto.mk:990: [...]/kmod-crypto-sha512_5.15.112-1_x86_64.ipk] Error 1
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
That was a workaround for OpenWrt generation of config files. This patch
was used to postpone returning from probe function until loading
firmware and calling register_wiphy().
All of that is not needed anymore thanks to the ieee80211 hotplug.d
script introduced in the commit 5f8f8a3661 ("base-files, mac80211,
broadcom-wl: wifi detection and configuration"). That takes care of
generating /etc/config/wireless entries even if wireless device appears
late in the booting process.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
IGD is only useful when accelerating a VM guest that wants to direct
render to memory in the host's framebuffer, but since OpenWrt
typically runs on headless hardware, this serves no purpose.
Also build vfio with VFIO_NOIOMMU undefined (to get all of the code
enabled), but allow it to be enabled via boot-time modparams
settings (or at run-time via sysfs writes to
"/sys/module/vfio/parameters/enable_unsafe_noiommu_mode".
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
adds ForceCommand option. If the command is specified,
it forces users to execute the command when they log in.
Signed-off-by: Nozomi Miyamori <inspc43313@yahoo.co.jp>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
A missing '\' caused the remaining parameters not to be passed to make.
This fixes the following error:
| gcc -c [...] fiptool.c -o fiptool.o
| In file included from fiptool.h:16,
| from fiptool.c:19:
|fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory
| 19 | # include <openssl/sha.h>
| | ^~~~~~~~~~~~~~~
|compilation terminated.
|make[3]: *** [Makefile:58: fiptool.o] Error 1
as the HOST_CFLAGS are no longer passed.
then, HOST_CFLAGS is specified as a command argument, this
is a specific problem of our built since appending these
needs the override directive.
Fixes: df28bfe03247 ("tfa-layerscape: Change to github and use the latest tag")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of tfa-layerscape has been changed from
codeuaurora to github. Also use the latest tag for Layerscape
Linux Development POC from NXP.
v2:
* restored ls1021a-afrdm board
* added platform defines to fiptool so ls-ddr-phy can be built
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of ppfe-firmware has been changed
from codeuaurora to github. Also use the latest tag for
Layerscape Linux Development POC from NXP.
Tested on:
* NXP FRWY-LS1012A
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of fman-ucode has been changed from
codeuaurora to github. Also use the latest tag for Layerscape
Linux Development POC from NXP.
Tested on:
* NXP LS1046A-RDB
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of uboot-layerscape has been changed
from codeuaurora to github. Also use the latest tag for
Layerscape Linux Development POC from NXP.
Tested on:
* NXP FRWY-LS1012A
* NXP LS1028A-RDB
* NXP LS1046A-RDB
V2: Remove ls1028ardb specifix fixups not needed with new uboot
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of ls-rcw has been changed from codeuaurora
to github. The reason is that the old codeaurora source no longer
resolves. Also use the latest tag for Layerscape Linux Development
POC from NXP.
Tested on:
* NXP FRWY-LS1012A
* NXP LS1046A-RDB
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE, Mention that previous codeaurora source is
no longer available)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The getrandom syscall is not hanging at bootup any more if there is
not enough entropy. This was fixed upstream in 2018 in commit:
a9cf659e05
This OpenWrt patch is not needed any more.
This reverts commit e64463ebde ("util-linux: avoid using the getrandom syscall")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following error:
* check_data_file_clashes: Package taskset wants to install file build_dir/target-powerpc_8548_musl/root-mpc85xx/usr/bin/taskset
But that file is already provided by package * busybox
* opkg_install_cmd: Cannot install package taskset.
Fixes: 3c3d797c4d ("busybox: enable taskset by default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes errors in the form of:
/Users/user/src/openwrt/openwrt/build_dir/hostpkg/json-c-0.16/json_util.c:63:35: error: a function declaration without a prototype is deprecated in all versions of C [-Werror,-Wstrict-prototypes]
const char *json_util_get_last_err()
^
void
1 error generated.
ninja: build stopped: subcommand failed.
Reported-by: Paul Spooren <mail@aparcar.org>
Suggested-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove upstramed patches:
- 100-configure.ac-fix-AC_ARG_WITH.patch
- 101-configure.ac-fix-cross-compilation.patch
Remove deprecated f2fstat tool:
https://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs-tools.git/commit/?id=77bf7ed29f1dd1341079913f3b36fc62f812c4f5
Changelog:
06c027a f2fs-tools: upgrade version 1.16.0
542cc57 fsck.f2fs: fix sanity check logic for cp_payload
a7df89e mkfs.f2fs: remove indentation
c82985a fsck.f2fs: don't call report_zone on normal partition
0ac168e f2fs-tools: relax zone size of power of 2
641be32 mkfs.f2fs: trim all the devices except the first one
3835fef f2fs-tools: fix # of total segments
5b08ca9 f2fs_io: support AES_256_HCTR2
ae3301c f2fs_io: Fix out of tree builds
ddbde27 fsck.f2fs: relocate chksum verification step during f2fs_do_mount()
77bf7ed f2fs-tools: Remove deprecated f2fstat
fb6575e Remove sg_write_buffer
1bb669e fsck.f2fs: avoid uncessary recalculation
ccd2361 fsck.f2fs: fix potential overflow of copying i_name
cd6b133 fsck.f2fs: add parentheses for SB_MASK
399600a dump.f2fs: remove unavailable option -g
3e6e178 f2fs-tools: define HAVE_CLOCK_GETTIME properly
907b972 f2fs-tools: support F2FS_IOC_START_ATOMIC_REPLACE
9ff70fb f2fs-tools: give less overprovisioning space
844f821 f2fs-tools: set host-aware zoned device similar to host-managed one
88ac76d fsck.f2fs: fix missing to assign c.zoned_model
8cbe34e fsck.f2fs: trigger repairing if filesystem has inconsistent errors
2f1dde2 fsck.f2fs: trigger repairing if filesystem was forced to stop
465159f fsck.f2fs: export valid image size
3486b62 mkfs.f2fs: update allocation policy for ro feature
bdd51e5 fsck.f2fs: fix __end_block_addr()
5a5e419 Always use sparse/sparse.h when building for Android
19f77c6 f2fs-tools: fix build error on lz4-1.9.4
986c1f1 Fix format strings in log messages
0d6acbe fsck.f2fs: use elapsed_time in checkpoint for period check
9b7a4c5 mkfs.f2fs: catch total_zones=0 instead of crashing
6148db3 f2fs-tools: use F2FS_BLKSIZE instead of PAGE_*_SIZE
f09c2b7 f2fs_io: support triggering filesystem GC via ioctl
32e7d27 configure.ac: fix cross compilation
65fe94e configure.ac: fix AC_ARG_WITH
6325cf7 Use F2FS_BLKSIZE as the size of struct f2fs_summary_block
c89be7a Use F2FS_BLKSIZE for dev_read_block() buffers
5317d18 Improve compile-time type checking for f2fs_report_zone()
92e2e52 Fix f2fs_report_zone()
648a491 Fix the struct f2fs_dentry_block definition
c964547 resize.f2fs: add option to manually specify new overprovision
a741438 fsck.f2fs: drop compression bit if inline_data is set
406b1c9 f2fs-tools: fix cannot get bdev information
9d0cb9e f2fs_io: add dsync option for write
a7b8b46 tools: fix file too large causing overflow
bddca6f dump.f2fs: add -I nid to dump inode by scan full disk
ebc3879 android_config: add time headers
c1144bf Check fallthrough in mount.h for Mac
bcb9929 avoid unnecessary function
7d902f4 Fix dependencies on linux/blkzoned.h when using Bionic.
274abbb Remove unnecessary config.h
8c97ab3 libzone: remove duplicate header
adcec10 Support zoned device if libc exists
efc2bc7 mkfs.f2fs: fix typo
3034a41 mkfs.f2fs: split unused parameter
dd8d8e5 f2fs-tools: do not use SG_IO in Android
4f216e6 f2fs-tools: move android_config before defining them
48c5dbb f2fscrypt: adjust config file first
4b55459 android_config: add missing uuid library
Signed-off-by: Nick Hainke <vincent@systemli.org>
This fixes the build of util-linux on powerpc and arc. Both CPU
architectures were not supported here in addition to the missing MIPS
support.
Fixes: 628a410ed1 ("util-linux: update to 2.39")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update to umdns HEAD to include latest enhancements for browse method
filtering, return of TXT records as an array, dumping IPv4/6 as an
array, and including the interface name in a browse reply.
Signed-off-by: Mark Baker <mark@vpost.net>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x, mt7621, x86_64
Add support for the FriendlyARM NanoPi R2C.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Instead of adding these common variables again and again simply create a
shared set for each SoC.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The Linux gpio-keys driver bindings allow for GPIO attached or interrupt
attached keys. Currently if an interrupt attached key is encountered
gpio_keys_button_probe() will fail due to not being able to get a gpio
descriptor:
gpio-keys: probe of gpio-keys failed with error -2
Skip the failure in the case of interrupt attached keys to resolve this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
5.15 is the first version to come with ksmbd. Use it instead of the
module as the linux one is better maintained.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This kernel config symbol is a shared library used for both CIFS and the
in-tree SMB_SERVER.
Split it out into kmod-fs-smbfs-common from kmod-fs-cifs, and depend on
it, so that later in-tree ksmbd may also depend on it.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
The BDFs for the:
Aruba AP-365
Devolo Magic 2 WiFi next
Edgecore ECW5410
Edgecore OAP100
Extreme Networks WS-AP3915i
GL.iNet GL-A1300
GL.iNet GL-AP1300
GL.iNet GL-S1300
Linksys EA8300
Linksys WHW03v2
Nokia Wi4A AC400i
P&W R619AC
Pakedge WR-1
Qxwlan E2600AC C1
Sony NCP-HG100/Cellular
Teltonika RUTX10
ZTE MF18A
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git.
Furthermore the BDFs for the:
8devices Habanero
8devices Jalapeno
Qxwlan E2600AC C2
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
TOZED TL70-C is an LTE CAT6 cellular modem based on UNISOC SL8563. UNISOC
was formerly called Spreadtrum hence the manufacturer name detected on the
modem is spreadtrum.
The connect and disconnect commands bring up and down the usb0 interface.
They are Base64 encoded as that's what the AT command accepts. The modem
can do up to 4 APNs by bringing the USB interfaces, usb0 to usb3, up.
Setting the USB interfaces up:
connmanctl ndisdial AT^NDISDUN="usb0",1,1
connmanctl ndisdial AT^NDISDUN="usb1",1,2
connmanctl ndisdial AT^NDISDUN="usb2",1,3
connmanctl ndisdial AT^NDISDUN="usb3",1,4
Setting the USB interfaces down:
connmanctl ndisdial AT^NDISDUN="usb0",0,1
connmanctl ndisdial AT^NDISDUN="usb1",0,2
connmanctl ndisdial AT^NDISDUN="usb2",0,3
connmanctl ndisdial AT^NDISDUN="usb3",0,4
Co-developed-by: Andre Cruz <me@1conan.com>
Signed-off-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
add description for medion usb lte webstick
Signed-off-by: Joe Cooper <highjagger+github@gmail.com>
[bump PKG_RELEASE]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
8f78aff2cb68 ubus: support multiple call return values
51f4dba67313 ucode: also link libresolv if ns_initparse() is not found
5c7d07773a59 uci: fix ctx.commit() without arguments
5163867269fc Merge pull request #148 from jow-/uci-fix-commit
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
With the update of selinux no package depends anymore on pcre in the
base repository. Move it to packages feed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Fixes error in the form of:
restripe.c: In function 'restore_stripes':
restripe.c:758:43: error: 'off64_t' undeclared (first use in this function); did you mean 'off_t'?
758 | (off64_t)read_offset) {
| ^~~~~~~
| off_t
restripe.c:758:43: note: each undeclared identifier is reported only once for each function it appears in
restripe.c:758:51: error: expected ')' before 'read_offset'
758 | (off64_t)read_offset) {
| ^~~~~~~~~~~
| )
restripe.c:757:36: note: to match this '('
757 | if (lseek64(source, read_offset, 0) !=
| ^
make[3]: *** [Makefile:193: restripe.o] Error 1
Fixes: fff878c5bc ("toolchain/musl: update to 1.2.4")
Signed-off-by: Nick Hainke <vincent@systemli.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces so
just having _GNU_SOURCE defined is not enough anymore.
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Fixes: fff878c5bc ("toolchain/musl: update to 1.2.4")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The firmware file for mt7601u (MediaTek MT7601U Wireless MACs) has
been moved to the mediatek/ folder by commit
8451c2b1 mt76xx: Move the old Mediatek WiFi firmware to mediatek
Address this by updating the location of the firmware file in our
linux-firmware Makefile generating the mt7601u-firmware package.
All other MediaTek Wi-Fi firmware files are supplied by OpenWrt's
own repository rather than being taken from linux-firmware.
Fixes: d53fe5d9ce ("linux-firmware: update to 20230515")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces so
just having _GNU_SOURCE defined is not enough anymore.
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Running autoreconf or autogen.sh is causing
the gettext-runtime subdirectory to have a configure script
that looks for and attempts to link to an external libunistring.
However, the macros and symbols for supporting that configuration
are not present in this subdirectory yet.
This results in some host machines to not build the
included libunistring objects for libgrt,
but at the same time, also not input the proper flag to the linker
for linking to an external library when it is found or even when
explicitly setting configuration to use a prefix for libunistring,
resulting in the common linking failure "undefined reference".
Some similar (and old...) upstream commits do the same thing,
but only for gettext-tools and libgettextpo.
Ref: ae943bcc1 ("Link with libunistring, if it exists.") # gettext.git
Ref: 61e21a72f ("Avoid link error in programs that use libgettextpo.") # gettext.git
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Add libunistring in order to link to gettext
and other packages directly
instead of the built-in substitute for it.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Fix compilation warning for unused variable for vr9.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/ltq-ptm-vr9/ltq-ptm/ifxmips_ptm_vdsl.c: In function 'mailbox_irq_handler':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/ltq-ptm-vr9/ltq-ptm/ifxmips_ptm_vdsl.c:560:9: error: unused variable 'i' [-Werror=unused-variable]
560 | int i;
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix multiple compilation warning for fallthrough and unused functions.
Fix compilation warning:
home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_VRX_TestParametersFeUpdate':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c:3359:17: error: unused variable 'nMsgId' [-Werror=unused-variable]
3359 | DSL_uint16_t nMsgId = EVT_PMD_TESTPARAMSGET;
| ^~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c:8310:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
8310 | bPreFail = DSL_TRUE;
| ~~~~~~~~~^~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c:8316:7: note: here
8316 | case DSL_LINESTATE_EXCEPTION:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/pm/drv_dsl_cpe_pm_core.c:2328:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2328 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/pm/drv_dsl_cpe_pm_core.c:2331:4: note: here
2331 | case DSL_PM_RESET_TOTAL:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c: In function 'DSL_ModuleCleanup':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c:1266:13: error: assignment to 'dev_t' {aka 'unsigned int'} from 'void *' makes integer from pointer without a cast [-Werror=int-conversion]
1266 | dsl_devt = NULL;
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c: At top level:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c:1178:13: error: 'DSL_DRV_NlSendMsg' defined but not used [-Werror=unused-function]
1178 | static void DSL_DRV_NlSendMsg(DSL_char_t* pMsg)
| ^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_msg_vrx.c:2459:20: error: 'DSL_DRV_VRX_SpreadArray' defined but not used [-Werror=unused-function]
2459 | static DSL_Error_t DSL_DRV_VRX_SpreadArray(
| ^~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning related to stack limit.
Fix compilation warning:
/builder/shared-workdir/build/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-vectoring-2019-05-20-4fa7ac30/src/vectoring/ifxmips_vectoring.c: In function 'proc_write_dbg':
/builder/shared-workdir/build/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-vectoring-2019-05-20-4fa7ac30/src/vectoring/ifxmips_vectoring.c:369:1: error: the frame size of 2088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
369 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Specifications:
SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz
RAM: 2x Winbond W9751G6KB-25 (128 MiB)
FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB)
WIFI1: Atheros AR9550 5.0GHz (SoC)
WIFI2: Atheros AR9582-AR1A 2.4GHz
WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz
PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN)
LED: 1x Power-LED, 1 x RGB Tricolor-LED
INPUT: One Reset Button
UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8
(VCC, RX, TX, GND - VCC is closest to the boot set jumper
under the console pins.)
Flashing instructions:
Depending on the installed firmware, there are vastly different
methods to flash a MR18. These have been documented on:
<https://openwrt.org/toh/meraki/mr18>
Tip:
Use an initramfs from a previous release and then use sysupgrade
to get to the later releases. This is because the initramfs can
no longer be built by the build-bots due to its size (>8 MiB).
Note on that:
Upgrades from AR71XX releases are possible, but they will
require the force sysupgrade option ( -F ).
Please backup your MR18's configuration before starting the
update. The reason here is that a lot of development happend
since AR71XX got removed, so I do advise to use the ( -n )
option for sysupgrade as well. This will cause the device
to drop the old AR71xx configuration and make a new
configurations from scratch.
Note on LEDs:
The LEDs has changed since AR71XX. The white LED is now used during
the boot and when upgrading instead of the green tricolor LED. The
technical reason is that currently the RGB-LED is brought up later
by a userspace daemon.
(added warning note about odm-caldata partition. remove initramfs -
it's too big to be built by the bots. MerakiNAND -> meraki-header.
sort nu801's targets)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
d4f56f0e6971 add support for handling traffic to/from the bridge device
3ea579064c00 nl: add separate socket for netlink commands
4ec5a51c6d01 nl: fetch packet stats for offloaded flows
0319fd080bf5 add support for configuring a fixed output port for a bridge member port
5b730f0c2cf5 bridger-bpf: fix build on older kernels
00af6c6e8350 nl: process IFLA_MASTER in any nl events, but skip wireless events
a2794f95756e bridger-bpf: add bpf_skb_pull_data call
6974093eb036 nl: rework vlan code to use the iflink API
d0f79a16c749 nl: do not attempt to enable flow offload on older kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allowing the (kernel) packet priority to be set through UCI.
This makes it straightforward to set some VLAN priority for DHCP
requests through a simple egress qos map. (Avoiding the need for
firewall matching and marking through iptables, which prevents using
flow offloading).
(Such priority tag is a hard requirement for some ISPs, such as Orange
in France).
Depends on: https://github.com/openwrt/odhcp6c/pull/74
Signed-off-by: Pacien TRAN-GIRARD <pacien.trangirard@pacien.net>
We only use 5.15 kernel. So remove all those unnecessary symbols
referencing 5.10 or 5.15 kernel.
Can be found with:
git grep -E 'LINUX_5_1(0|5)'
Note that we remove the dependency from "sound-soc-chipdip-dac" instead
of removing the complete kernel package. The 5.15 version bump forgot to
delete the "@LINUX_5_10" dependency. The kernel package is still needed
in 5.15 kernel.
Signed-off-by: Nick Hainke <vincent@systemli.org>
We removed 5.10 kernel, so remove also the patch that only affects 5.10
kernels.
Manually refresh:
- 0005-SSDK-config-add-kernel-5.15.patch
- 0010-QSDK-config-Avoid-Werror-heroics.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fix compilation warning from ret not handled from copy_from_user and
missing fallthrough.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_bbd.c: In function 'vmmc_BBD_WhiteListedCmdWr':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_bbd.c:1012:16: error: this statement may fall through [-Werror=implicit-fallthrough=]
1012 | if (IFX_TRUE == pCh->pParent->bSlicSupportsIdleMode)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_bbd.c:1028:7: note: here
1028 | case VMMC_WL_SDD_RING_CFG:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c: In function 'VMMC_Dev_Spec_Ioctl':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:111:15: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
111 | copy_from_user (p_arg, (IFX_uint8_t*)ioarg, sizeof(arg));\
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:475:7: note: in expansion of macro 'ON_IOCTL'
475 | ON_IOCTL((VMMC_CHANNEL *) pLLDummyCh,
| ^~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:113:15: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
113 | copy_to_user ((IFX_uint8_t*)ioarg, p_arg, sizeof(arg));\
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:475:7: note: in expansion of macro 'ON_IOCTL'
475 | ON_IOCTL((VMMC_CHANNEL *) pLLDummyCh,
| ^~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for switch fallthrough and
copy_to_user ret not handled.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c: In function 'ifx_tapi_dial_OnTimer':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c:318:38: error: this statement may fall through [-Werror=implicit-fallthrough=]
318 | pTapiDialData->nHookChanges = 0;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c:322:7: note: here
322 | case TAPI_HOOK_STATE_DIAL_L_VAL:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c: In function 'IFX_TAPI_Event_Dispatch_ProcessCtx':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c:1546:30: error: this statement may fall through [-Werror=implicit-fallthrough=]
1546 | pEvent->ch = IFX_TAPI_DEVICE_CH_NUMBER;
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c:1548:16: note: here
1548 | case IFX_TAPI_ERRSRC_LL_CH:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c: In function 'TAPI_IoctlDev':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:705:19: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
705 | copy_to_user ((IFX_void_t*)ioarg, p_tmp, sizeof(IFX_TAPI_CAP_t));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c: In function 'TAPI_IoctlCh':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:1553:14: error: this statement may fall through [-Werror=implicit-fallthrough=]
1553 | ret = TAPI_statusNotSupported;
| ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:1555:7: note: here
1555 | default:
| ^~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_fsm_alert_exec':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2037:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2037 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2039:7: note: here
2039 | case 1:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2053:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2053 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2055:7: note: here
2055 | case 2:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2070:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2070 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2072:7: note: here
2072 | default:
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_prepare_data':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1501:13: error: this statement may fall through [-Werror=implicit-fallthrough=]
1501 | if (IFX_TAPI_CID_HM_ONHOOK == pTxData->txHookMode)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1509:7: note: here
1509 | default:
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1531:16: error: this statement may fall through [-Werror=implicit-fallthrough=]
1531 | if (IFX_TAPI_CID_STD_KPN_DTMF_FSK != pConfData->nStandard)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1535:10: note: here
1535 | case IFX_TAPI_CID_GEN_TYPE_FSK:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_lookup_transparent':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1425:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
1425 | cidfsk_set_tx_time (pTxData, &pConfData->TapiCidFskConf);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1427:7: note: here
1427 | case IFX_TAPI_CID_GEN_TYPE_DTMF:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'TAPI_Phone_CID_Stop_Tx':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3445:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
3445 | switch (pTxData->nAlertType)
| ^~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3461:7: note: here
3461 | case TAPI_CID_STATE_ACK:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3463:13: error: this statement may fall through [-Werror=implicit-fallthrough=]
3463 | if (ptr_chk(pDrvCtx->SIG.DTMFD_Override, ""))
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3472:7: note: here
3472 | case TAPI_CID_STATE_SENDING:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'TAPI_Phone_Get_CidRxData':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:4060:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
4060 | if (IFX_Fifo_isEmpty(&(pCidRx->TapiCidRxFifo)))
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:4069:4: note: here
4069 | default:
| ^~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning caused by copy_from_user ret not handled.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ltq_atm.c: In function 'ppe_ioctl':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ltq_atm.c:341:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
341 | copy_from_user(&mib_vcc, arg, sizeof(mib_vcc));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning from missing fallthrough
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c: In function 'DSL_DRV_AutobootControlSet':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c:2648:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
2648 | if (pContext->bAutobootThreadStarted)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c:2656:13: note: here
2656 | case DSL_AUTOBOOT_CTRL_STOP_PD:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2358:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2358 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2361:4: note: here
2361 | case DSL_PM_RESET_TOTAL:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2365:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2365 | if (ResetType == DSL_PM_RESET_TOTAL)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2368:4: note: here
2368 | case DSL_PM_RESET_HISTORY_SHOWTIME:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c:8883:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
8883 | bPreFail = DSL_TRUE;
| ~~~~~~~~~^~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c:8889:7: note: here
8889 | case DSL_LINESTATE_EXCEPTION:
| ^~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for some debugfs entry defined but
unused.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:969:12: error: 'proc_read_genconf' defined but not used [-Werror=unused-function]
969 | static int proc_read_genconf(char *page, char **start, off_t off, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:942:12: error: 'proc_write_wanmib' defined but not used [-Werror=unused-function]
942 | static int proc_write_wanmib(struct file *file, const char *buf, unsigned long count, void *data)
| ^~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:910:12: error: 'proc_read_wanmib' defined but not used [-Werror=unused-function]
910 | static int proc_read_wanmib(char *page, char **start, off_t off, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:892:12: error: 'proc_read_version' defined but not used [-Werror=unused-function]
892 | static int proc_read_version(char *buf, char **start, off_t offset, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:1164:19: error: 'stricmp' defined but not used [-Werror=unused-function]
1164 | static INLINE int stricmp(const char *p1, const char *p2)
| ^~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning due to not handled switch
fallthrough, stack limit and compilation warning in g997 module.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2277:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2277 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2280:4: note: here
2280 | case DSL_PM_RESET_TOTAL:
| ^~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2284:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2284 | if (ResetType == DSL_PM_RESET_TOTAL)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2287:4: note: here
2287 | case DSL_PM_RESET_HISTORY_SHOWTIME:
| ^~~~
cc1: all warnings being treated as errors
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c:3189:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
3189 | if (nErrCode != DSL_SUCCESS)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c:3197:13: note: here
3197 | case DSL_LINESTATE_IDLE:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c: In function 'DSL_DRV_DEV_G997_PowerManagementStateForcedTrigger':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c:2532:52: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
2532 | else if (((nVal >> 4) & 0x15) == 0x9)
| ^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c: In function 'DSL_DRV_DEV_G997_DeltHlogGet':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c:2108:1: error: the frame size of 1056 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
2108 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add multiple patch to make the package compilable again.
Aside from some fixup of obvius wrong code, some real fix were needed.
This fix any compilation warning found on compiling the package on
bcm47xx. (omitted since they are too much)
The real problem of this package was the missing MODULE_LICENSE now
mandatory even without WERROR. Set to Proprietary.
And the big blocker is that Broadcom provided an object file targetting
an old kernel version.
The module on modprobe try to find the symbol printk but printk was
dropped and replaced to _printk.
To handle this change we use objcopy tool to rename the symbol to the
new name permitting a correct modprobe and creation of .ko
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning on 64bit systems.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/fwcmd.c: In function 'mwl_fwcmd_get_fw_core_dump':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/fwcmd.c:3608:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
3608 | (const void *)((u32)pcmd +
| ^
In file included from ./include/linux/device.h:15,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/device.h:3,
from ./include/linux/dma-mapping.h:7,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/dma-mapping.h:3,
from ./include/linux/skbuff.h:31,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/etherdevice.h:3,
from /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:20:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c: In function 'pcie_tx_init_ndp':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:38: error: format '%d' expects argument of type 'int', but argument 3 has type 'long unsigned int' [-Werror=format=]
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:17: note: in expansion of macro 'wiphy_err'
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:67: note: format string is defined here
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ~^
| |
| int
| %ld
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:38: error: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Werror=format=]
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:17: note: in expansion of macro 'wiphy_err'
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:71: note: format string is defined here
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ~^
| |
| int
| %ld
CC [M] /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.o
In file included from ./include/linux/device.h:15,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/device.h:3,
from ./include/linux/dma-mapping.h:7,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/dma-mapping.h:3,
from ./include/linux/skbuff.h:31,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/etherdevice.h:3,
from /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:19:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c: In function 'pcie_bf_mimo_ctrl_decode':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:1325:37: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
1325 | filename, (unsigned int)fp_data);
| ^
./include/linux/dev_printk.h:110:37: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:1324:17: note: in expansion of macro 'wiphy_err'
1324 | wiphy_err(priv->hw->wiphy, "Error opening %s! %x\n",
| ^~~~~~~~~
cc1: all warnings being treated as errors
make[4]: *** [scripts/Makefile.build:289: /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.o] Error 1
make[4]: *** Waiting for unfinished jobs....
cc1: all warnings being treated as errors
make[4]: *** [scripts/Makefile.build:289: /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.o] Error 1
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.c: In function 'mwl_debugfs_regrdwr_read':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.c:1335:43: error: format '%d' expects argument of type 'int', but argument 4 has type 'ssize_t' {aka 'long int'} [-Werror=format=]
1335 | "error: %d(%u 0x%08x 0x%08x)\n",
| ~^
| |
| int
| %ld
1336 | ret, priv->reg_type, priv->reg_offset,
| ~~~
| |
| ssize_t {aka long int}
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Alloc MIB struct dynamically instead to fix compilation warning for
stack limit.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_chromium/vrx518_tc_drv-ugw_8.5.2.10/dcdp/ptm_tc.c: In function 'ptm_tc_get_stats':
/__w/openwrt/openwrt/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_chromium/vrx518_tc_drv-ugw_8.5.2.10/dcdp/ptm_tc.c:463:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
463 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for atm_tc module.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/vrx518_tc_drv-ugw_8.5.2.10/dcdp/atm_tc.c: In function 'print_datetime':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/vrx518_tc_drv-ugw_8.5.2.10/dcdp/atm_tc.c:768:32: error: argument to 'sizeof' in 'snprintf' call is the same expression as the destination; did you mean to provide an explicit length? [-Werror=sizeof-pointer-memaccess]
768 | snprintf(buffer, sizeof(buffer), "%s.%06d", tmbuf, (int)datetime->tv_nsec / 1000);
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop set_fs and get_fs since they are not present in kernel > 5.13.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c: In function 'dev_wlc_ioctl':
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:121:14: error: implicit declaration of function 'get_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
121 | fs = get_fs();
| ^~~~~~
| sget_fc
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:121:14: error: incompatible types when assigning to type 'mm_segment_t' from type 'int'
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:122:9: error: implicit declaration of function 'set_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
122 | set_fs(KERNEL_DS);
| ^~~~~~
| sget_fc
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:122:16: error: 'KERNEL_DS' undeclared (first use in this function); did you mean 'KERNFS_NS'?
122 | set_fs(KERNEL_DS);
| ^~~~~~~~~
| KERNFS_NS
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning related to if clause not guarding in
wl_iw.c
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c: In function 'wl_iw_set_freq':
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:393:9: error: this 'if' clause does not guard... [-Werror=misleading-indentation]
393 | if (fwrq->m > 4000 && fwrq->m < 5000)
| ^~
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:396:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'if'
396 | chan = wf_mhz2channel(fwrq->m, sf);
| ^~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for copy_from_user ret value not handled.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c: In function 'DSL_BSP_FWDownload':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c:1623:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1623 | copy_from_user ((char *) &img_hdr_tmp, buf, sizeof (img_hdr_tmp));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c:1701:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1701 | copy_from_user (mem_ptr, buf + nRead, nCopy);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If CPTCFG_BRCMFMAC_SDIO is not used brcmf_of_fwnames is defined but not
used in the case of CONFIG_OF not compiled.
Restrict brcmf_of_fwnames only with CPTCFG_BRCMFMAC_SDIO selected.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-x86_64-openwrt-linux-musl_musl/linux-x86_64/backports-6.1.24/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.h:16:1: error: 'brcmf_of_fwnames' defined but not used [-Werror=unused-function]
16 | brcmf_of_fwnames(struct device *dev, u32 *map_count)
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for debug level read.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/ath10k-ct-regular/ath10k-ct-2022-05-13-f808496f/ath10k-5.15/debug.c: In function 'ath10k_read_debug_level': /__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/ath10k-ct-regular/ath10k-ct-2022-05-13-f808496f/ath10k-5.15/debug.c:1388:1: error: the frame size of 1440 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
1388 | }
| ^
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Handle error from copy_to_user in read_file_eeprom.
Fix compilarion warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-x86_64-openwrt-linux-musl_musl/linux-x86_64/backports-6.1.24/drivers/net/wireless/ath/ath9k/debug.c: In function 'read_file_eeprom':
/__w/openwrt/openwrt/openwrt/build_dir/target-x86_64-openwrt-linux-musl_musl/linux-x86_64/backports-6.1.24/drivers/net/wireless/ath/ath9k/debug.c:1451:17: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1451 | copy_to_user(user_buf, from, bytes);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
4c5beee get rid of VLA on the stack, and fix the resulting error of a too large stack frame
80dda1d Fix LAN->WAN ping failure with over MTU size on outgoing interface
Commit 4c5beee as a side effect fix a compilation warning with
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/nat46-2022-03-30-95ca1c3b/nat46/modules/nat46-netdev.c: In function 'nat46_remove':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/nat46-2022-03-30-95ca1c3b/nat46/modules/nat46-netdev.c:260:9: error: ISO C90 forbids variable length array 'config_remove' [-Werror=vla]
260 | char config_remove[buflen];
| ^~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/nat46-2022-03-30-95ca1c3b/nat46/modules/nat46-netdev.c:280:17: error: ISO C90 forbids variable length array 'config' [-Werror=vla]
280 | char config[buflen];
| ^~~~
cc1: all warnings being treated as errors
Also this now require nf_defrag_ipv6 as a new dependency.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The index.json file lies next to Packages index files and contains a
json dict with the package architecture and a dict of package names and
versions.
This can be used for downstream project to know what packages in which
versions are available.
Signed-off-by: Paul Spooren <mail@aparcar.org>
When using OpenWRT with DSA and 'lan' ports, we could get an empty
`next_eth`. This is of course not desirable, as this causes `sh: out of
range` errors when trying to determine which one would be greater.
It turns out, that we don't even need this check at all because, when
looking for all existin eth*s on a system, and take the highest index
and then iterate a set of devices and rename to eth${highest_index+n},
it is guaranteed that there will be no conflict.
Fixes: b688bf83f9 ("base-files: rename ethernet devs on known boards")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Hardware specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 16 MB (Macronix MX25L12835FM2I-10G)
- RAM: 128 MB (Nanya NT5CC64M16GP-DI)
- WLAN 2.4 GHz: 2x2 MediaTek MT7603EN
- WLAN 5 GHz: 2x2 MediaTek MT7615N
- Ethernet: 1x 10/100/1000 Mbps
- LED: Power, Wifi, WPS
- Button: Reset, WPS
- UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port)
Serial console @ 57600,8n1
Flash instructions:
Connect to serial console and start up the device. As the bootloader got
locked you need to type in a password to unlock U-Boot access.
When you see the following output on the console:
relocate_code Pointer at: 87f1c000
type in the super secure password:
1234567890
Then select TFTP boot from RAM by selecting option 1 in the boot menu.
As Linksys decided to leave out a basic TFTP configuration you need to
set server- & client ip as well as the image filename the device will
search for. You need to use the initramfs openwrt image for the TFTP
boot process.
Once openwrt has booted up, upload the sysupgrade image via scp and run
sysupgrade as normal.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Kmod-mhi-pci-generic supports Qualcomm modems over PCIe bus. On targets
without PCI support, this package is empty. Symbol CONFIG_MHI_BUS_PCI_GENERIC
depends on CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kmod-serial-8250-exar supports Serial cards connected via PCIe bus. On targets
without PCI support, this package is empty.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kmod-i2c-designware-pci supports Synopsys I2C over PCIe bus. On targets
without PCI support, this package is empty. Symbol CONFIG_I2C_DESIGNWARE_PCI
depends on CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Add support for the Firefly ROC-RK3328-CC.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Support uboot for NXP LS1028ARDB reference board. GIC V3 has to
be disabled in the uboot config to allow booting upstream kernels.
This patch can be dropped once uboot is updated to 2022.04 version
to nxp-qoriq github lf-6.1.1 branch.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
There seems to be a difference in firmware calling convention
between upstream and NXP kernels. On some cpus like ls1028
it will hang on firmware secure get random when using LF uboot
with upstream kernel. Instead of commenting it out, don't call
get radnom seed when "kaslr-seed" is not present in device tree.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
To support the widest variety of modems, allow restoring previous
behaviour of configuring the link throug means of DHCP(v6) exclusively.
Change the default value of "dhcp" and "dhcpv6" UCI options to "auto",
while keeping the default behaviour of "prefer out-of-band configuration",
intact. Setting "dhcp" or "dhcpv6" to boolean 1 will now force using
DHCP and DHCPv6, respectively.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
This replaces the 160MHz with the upstreamed one, fixes 6GHz only WIPHY
registration, allows SAR usage on WCN6750 and plenty of REO fixes.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changes:
43f81b4 wireless-regdb: update regulatory database based on preceding changes
66f245d wireless-regdb: Update regulatory rules for Hong Kong (HK)
e78c450 wireless-regdb: update regulatory rules for India (IN)
1647bb6 wireless-regdb: Update regulatory rules for Russia (RU). Remove DFS requirement.
c076f21 Update regulatory info for Russia (RU) on 6GHz
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
Using the local gnulib source during autogen.sh
allows for fine-grained control over the macros
and source files for use with gettext
but part of gnulib instead of gettext,
without having to wait for a release
or deal with gnulib as a git submodule.
This is an alternative to running autoreconf.
It also removes the need to patch macros
in the case where there is a conflict
between the source and our aclocal directory.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Some users have reported that gettext builds
are attempting to link to libxml2
while it was supposed to be configured
to use it's own built-in substitute.
Configure gettext to require and link
to our local libxml2 explicitly.
Add a patch to revert upstream commit 87927a4e2
which forces libtextstyle to use the built-in libxml,
no matter what the configuration is,
making that option configurable again
after the configure script is regenerated.
Reported-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Instead of editing the SUBDIRS variable with a patch,
it can be overriden at the end of the command line when invoking Make.
This tool has a series of recursive Makefiles in each subdirectory,
therefore SUBDIRS is set to a pattern of Make functions
so that the result is variable depending on the current subdirectory
that Make is being invoked in.
Some of the subdirectories don't have a Makefile and are just storing files
for another subdirectory Makefile target,
therefore we have to place a fake Makefile that does nothing.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The image_header_t typedef has been removed from
uboot v2023.01 [1], replaced with legacy struct.
[1] f3543e6944
Fixes: 3d5c542 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
CONFIG_SYS_TEXT_BASE has been renamed to CONFIG_TEXT_BASE
in uboot v2023.01 [1], fixes all this variable.
[1] 984639039f
Fixes: 3d5c5427 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.
Specifications
==============
SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)
MAC address assignment
======================
The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.
The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.
Installation (web interface)
============================
The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.
The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.
1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy
NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.
Installation (UART method)
==========================
The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:
1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation
Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:
nand read 1800000 53c0000 800
mw.b 1800004 1 1
nand erase 53c0000 800
nand write 1800000 53c0000 800
This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.
Back to stock
=============
It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.
It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:
mtd write zyxel.bin Kernel2
echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
In MBIM interfaces, DNS servers may be provided out-of-band regardless
whether DHCP is used for configuration, or not. Move the DNS
configuration outside "if" blocks to support that.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Beginnings and endings of sub-interface creation procedure were
literally duplicates - extract them outside if "if" blocks
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Allow setting interface MTU through UCI. If this is not set,
use MBIM-provided MTU, if provided through control channel.
If separate MTUs are provided for IPv4 and IPv6, apply larger of them.
This is very unlikely and possible only for IPv4v6 dual-stack configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Delegate prefixes received through MBIM control channel the same way, as
would be done through DHCP, according to RFC7278.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
MBIM supports multiple values for IP address and DNS server, and such
configuration is available through output of MBIM. Use new helper
method to support adding multiple addresses and DNS servers to static
interfaces for both IPv4 and IPv6.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add a new helper to extract IP configuration from umbim output. This is
required to extract fields which can possibly have multiple values,
namely IP addresses and DNS servers, and get rid of primitive parser
using 'eval' builtin without support for this.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Display full configuration obtained using MBIM control channel in the
log, from umbim output verbatim, for easier troubleshooting, and in
preparation for parser refactoring.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Inspired by commti e51aa699f7, allow setting specific routing tables
via ip4table and ip6table options, by passing them on child interfaces
created by MBIM protocol handler.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Finally, inspired by ModemManager's logic, make static configuration
obtained through MBIM control channel, preferred.
If IP configuration is not available this way, fallback to DHCP(v6) if
enabled, else do not create a sub-interface for unavailable IP type.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Now, that sub-interface setup is split by IP type, and separate checks
are performed for DHCP selection, it is possible to control DHCP on v4
an v6 sub-interfaces instantly. Add "dhcpv6" variable, akin to QMI
option, to control behaviour of DHCPv6 separately from IPv4 option,
which is required for some mobile operators.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Check whether interface is configured per IP type, not per DHCP. This is
preparation to allow fallback to DHCP if static IP configuration is not
available, which is the default option for MBIM modems
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Fix an issue where subinterfaces were not added to the same
firewall zone as their parent.
Inspired by 64bb88841f.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
MBIM protocol handler should intherit "peerdns" options from parent
interface on sub-interfaces, otherwise upstream DNS servers are applied
regardless of configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Previously, DHCP was used. According to MBIM Specification v1.0 errata 1 [1],
section 10.5.20, MBIM_CID_IP_CONFIGURATION,
if MBIM information element containing IP configuration is available,
host shall use it, and fall back to in-band mechanisms to acquire it therwise -
therefore make static configuration the default.
[1] https://www.usb.org/document-library/mobile-broadband-interface-model-v10-errata-1-and-adopters-agreement
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Current implementation needlessly creates both IPv4 and IPv6
sub-interfaces for single-stack IP types. Limit this only to selected IP
type. While at that, ensure that IP type is also passed to umbim during
"connect" phase. In addition, detect the actual established connection
type returned by umbim and set up subinterfaces according to that,
not to requested configuration. While at that, allow empty IP type explicitly,
interpreted as "any" according to MBIM specification.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Subsequent calls to 'umbim connect' do not have any effect if a failure
occured, and in such case an infinite loop without timeout is created,
leading to possibility of interface stuck at connecting forever.
Drop this loop, and issue MBIM disconnect properly, so netifd can
restart from scratch.
This issue can be observed with Sierra EM7455 at changing APN, which
causes network re-registration by default, and a MBIM transaction
timeout, which is resolved on next interface bringup by netifd.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Previous implementation automatically set up connections for both IPv4
and IPv6, even if one of them isn't supported. Respect the "pdptype"
option in the same way, as it is done for QMI or NCM, and only start the
respective PDN sessions, if set.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
There are mbim compatible wwan modules available which do not support
the dhcp autoconfiguration. (e.g. gemalto Cinterion ELS81)
This adds the possibility to get the configuration parameters from mbim.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This applies commit 02ac9c94 to fix this OpenSSL Security Advisory
issued on 20th April 2023[1]:
Input buffer over-read in AES-XTS implementation on 64 bit ARM
(CVE-2023-1255)
==============================================================
Severity: Low
Issue summary: The AES-XTS cipher decryption implementation for 64 bit
ARM platform contains a bug that could cause it to read past the input
buffer, leading to a crash.
Impact summary: Applications that use the AES-XTS algorithm on the 64
bit ARM platform can crash in rare circumstances. The AES-XTS algorithm
is usually used for disk encryption.
The AES-XTS cipher decryption implementation for 64 bit ARM platform
will read past the end of the ciphertext buffer if the ciphertext size
is 4 mod 5 in 16 byte blocks, e.g. 144 bytes or 1024 bytes. If the
memory after the ciphertext buffer is unmapped, this will trigger a
crash which results in a denial of service.
If an attacker can control the size and location of the ciphertext
buffer being decrypted by an application using AES-XTS on 64 bit ARM,
the application is affected. This is fairly unlikely making this issue a
Low severity one.
1. https://www.openssl.org/news/secadv/20230420.txt
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The resize tool will resize the prompt to match the current terminal
size. This is helpful when connecting to the system using UART to make
the vi or top output match the current terminal size.
This increases the busybox binary size by 136 bytes and the ipkg size by
335 bytes on aarch64.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Alcatel HH40V is a CAT4 LTE router used by various ISPs.
Specifications
==============
SoC: QCA9531 650MHz
RAM: 128MiB
Flash: 32MiB SPI NOR
LAN: 1x 10/100MBit
WAN: 1x 10/100MBit
LTE: MDM9607 USB 2.0 (rndis configuration)
WiFi: 802.11n (SoC integrated)
MAC address assignment
======================
There are three MAC addresses stored in the flash ROM, the assignment
follows stock. The MAC on the label is the WiFi MAC address.
Installation (TFTP)
===================
1. Connect serial console
2. Configure static IP to 192.168.1.112
3. Put OpenWrt factory.bin file as firmware-system.bin
4. Press Power + WPS and plug in power
5. Keep buttons pressed until TFTP requests are visible
6. Wait for the system to finish flashing and wait for reboot
7. Bootup will fail as the kernel offset is wrong
8. Run "setenv bootcmd bootm 0x9f150000"
9. Reset board and enjoy OpenWrt
Installation (without UART)
===========================
Installation without UART is a bit tricky and requires several steps too
long for the commit message. Basic steps:
1. Create configure backup
2. Patch backup file to enable SSH
3. Login via SSH and configure the new bootcmd
3. Flash OpenWrt factory.bin image manually (sysupgrade doesn't work)
More detailed instructions will be provided on the Wiki page.
Tested by: Christian Heuff <christian@heuff.at>
Signed-off-by: Andreas Böhler <dev@aboehler.at>
By default both kmod-bcma and kmod-ssb are selected by kmod-b43.
However, only one of both modules is needed for bmips subtargets:
- bcma: bcm6318, bcm6328, bcm6362, bcm63268
- ssb: bcm6358, bcm6368
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds generic kernel support for Broadcom Fallback SPROMs so that it can be
used in any target, even non Broadcom ones.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds a new package with Broadcom SPROMs that can be used as fallback when
the devices lack physical SPROMs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build
for replacement loader for both TL-XDR6086 and TL-XDR6088. The only
difference at U-Boot level is the different filename requested via
TFTP, matching the corresponding OpenWrt build artifacts for each
device.
The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088
except for the wireless part. Also create a uboot for the TP-Link
TL-XDR4288.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[rebase to uboot 23.04, correct led and button]
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
U-Boot commit ea6fdc13595 ("dm: button: add support for linux_code in
button-gpio.c driver") makes it mandatory to specify linux,code for all
buttons. As that broke handling of the reset button in U-Boot with the
update to U-Boot 2023.04, add linux,code for all butons.
Reported-by: @DragonBluep
Fixes: 50f7c5af4a ("uboot-mediatek: update to v2023.04")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
qrtr/ns.ko is now merged into qrtr/qrtr.ko, so drop the individual module packaging.
Fixes: f4989239cc ("kernel: bump 5.15 to 5.15.107")
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, mt7621/dap-x1860
upstream PR 408 improvements:
-Fix AMSDU packets unused
-Removed the ASMDU packets queue
-Add more info in the iw tool
-fix is_hw_crypto_enabled
-Optimization AMPDU_TX_OPERATIONAL (avoid a spinlock)
change to wongsyrone mod
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
QCA has finally sent a proper fixup for the 160MHz regression upstream,
so lets use the pending fix which also properly sets center frequency 2
in case 80+80 MHz is used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 9d96b6fb72 ("ath79/mikrotik: disable building NAND images")
disabled building images for MikroTik devices with NAND flash due to a
less than satisfactory method used for updating the kernel on those
devices back then.
To address the problem, add support for updating the kernel on MikroTik
devices with NAND flash using a new tool, Yafut, which enables copying
files from/to Yaffs file systems even if the kernel does not have native
support for the Yaffs file system compiled in. Instead of erasing the
entire NAND partition holding the kernel during every system upgrade
(which is what the previously-used approach employing kernel2minor
involved), Yafut preserves the Yaffs filesystem present on that
partition and only replaces the kernel executable. This allows bad
block information to be preserved across sysupgrade runs and also
enables wear leveling on the NAND partition holding the kernel. Yafut
does not rely on kernel2minor in any way and intends to eventually
supersede the latter for NAND devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Updating to U-Boot 2023.04 broke the build for the RAVPower RP-WD009
MT7628 board. This was due to upstream conversion of CONFIG_* to CFG_*
which was not applied to our downstream patch adding support for the
RAVPower RP-WD009 device.
Apply CONFIG_* to CFG_* converion analog to what has been done also
for mt7928_rfb upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update to next U-Boot timed release.
Remove now obsolete patch
100-01-board-mediatek-add-more-network-configurations.patch
Default IP addresses are now dealt with in Kconfig, no longer in board-
specific C header files.
Add patches to restore ANSI support in bootmenu which was broken upstream,
always use high-speed mode on serial UART for improved stability and fix
an issue with pinconf not being applied on MT7623 resulting in eMMC
being inaccessible when booting from micro SD card.
In order to keep the size of the bootloader on MT7623 below 512kB remove
some unneeded commands on both MT7623 boards.
Tested on:
* BananaPi BPi-R2 (MT7623N)
* BananaPi BPi-R3 (MT7986A)
* BananaPi BPi-R64 (MT7622A)
* Linksys E8450 (MT7622B)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a silent command that allows easy wifi up/down automation for
scripts.
It takes one or multiple devices as arguments (or all if none are passed),
and the exit code indicates if any of those is not up.
E.g.:
wifi isup && echo "all wifi devices are up"
wifi isup radio0 || echo "this wifi is down"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Use the already present but unused $cmd and $dev variables instead of
positional parameters in ubus_wifi_cmd() to improve readability.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
This replaces the management TLV pending fix with the upstreamed one,
fixes traffic flooding when AP and monitor modes are used at the same time,
fixes QCN9074 always showing -95 dBm for station RSSI in dumps,
fixes potential crash on boot if spectral scan is enabled due to writing to
unitialized memory and adds 11d scan offloading for WCN6750 and WCN6855.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, during initialization ath11k will receive a regulatory event
from the firmware in which it will receive the default regulatory domain
code and accompanying rules list and report those to the kernel.
Then if you try to change the regulatory domain to a different country code
it will do a weird thing in which it will send that to the FW and after
receiving the appropriate regulatory event it will parse the rules.
However, while its parsing there is a weird thing being done, and that is
that new raw rules from FW get intersected with the rules from the default
domain.
This is creating a big issue as the default domain is almost always set to
"US" or just "00" aka world so ath11k will unfairly limit you to the most
restrictive combination of rules based on the default domain and your
desired domain.
For example, in ETSI countries this is causing channels 12 and 13 on 2.4GHz
to not be usable since "US" limits 2.4GHz to 2472MHz instead of 2482MHz
like ETSI countries do.
So, lets do what TIP and even QCA do in their ath11k downstream tree and
completely get rid of the interesection code in ath11k.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using "ubiformat" with stdin it requires passing image size using
the -S argument. Provide it just like we do for "ubiupdatevol".
This fixes:
ubiformat: error!: must use '-S' with non-zero value when reading from stdin
This change fixes sysupgrade for bcm53xx and bcm4908 NAND devices
possibly some other targets too.
Cc: Rodrigo Balerdi <lanchon@gmail.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Fixes: 9710712120 ("base-files: accept gzipped nand sysupgrade images")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
CRYPTO_USER_API_ENABLE_OBSOLETE config symbol depends on CRYPTO_USER so
lets add this dependency to relevant modules.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
While tracking one bug report related to wrong package dependencies I've
noticed, that a bunch of the crypto modules are actually not
architecture specific, but either board/subtarget (x86/64) or board
(mpc85xx) specific.
So lets fix it, by making those modules architecture specific:
x86/64 -> x86_64
mpc85xx -> powerpc
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: NXP P1010 (1x e500 @ 800MHz)
RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9)
FLASH: 32M NOR (Spansion S25FL256S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035)
UART: 115200 8N1 (RJ-45 Cisco)
Installation
------------
1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in
the root directory of a TFTP server and serve it at
192.168.1.66/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Alter the bootcmd in U-Boot:
$ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm"
$ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000;
bootm 0x2000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
4. Boot the initramfs image
$ run ramboot_openwrt
5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install
using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: David Bauer <mail@david-bauer.net>
Apply two patches fixing low-severity vulnerabilities related to
certificate policies validation:
- Excessive Resource Usage Verifying X.509 Policy Constraints
(CVE-2023-0464)
Severity: Low
A security vulnerability has been identified in all supported versions
of OpenSSL related to the verification of X.509 certificate chains
that include policy constraints. Attackers may be able to exploit
this vulnerability by creating a malicious certificate chain that
triggers exponential use of computational resources, leading to a
denial-of-service (DoS) attack on affected systems.
Policy processing is disabled by default but can be enabled by passing
the `-policy' argument to the command line utilities or by calling the
`X509_VERIFY_PARAM_set1_policies()' function.
- Invalid certificate policies in leaf certificates are silently ignored
(CVE-2023-0465)
Severity: Low
Applications that use a non-default option when verifying certificates
may be vulnerable to an attack from a malicious CA to circumvent
certain checks.
Invalid certificate policies in leaf certificates are silently ignored
by OpenSSL and other certificate policy checks are skipped for that
certificate. A malicious CA could use this to deliberately assert
invalid certificate policies in order to circumvent policy checking on
the certificate altogether.
Policy processing is disabled by default but can be enabled by passing
the `-policy' argument to the command line utilities or by calling the
`X509_VERIFY_PARAM_set1_policies()' function.
Note: OpenSSL also released a fix for low-severity security advisory
CVE-2023-466. It is not included here because the fix only changes the
documentation, which is not built nor included in any OpenWrt package.
Due to the low-severity of these issues, there will be not be an
immediate new release of OpenSSL.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Current WLAN.HK.2.5.0.1 FW is quite old and buggy, but we had to hold off
from updating to 2.6.0.1 and 2.7.0.1 as they had compatibility regressions,
but now QCA finally released 2.9.0.1 FW which is working on all of the
boards.
So finally update IPQ8074 and QCN9074 FW to the latest
WLAN.HK.2.9.0.1-01385-QCAHKSWPL_SILICONZ-1 firmware.
In order to do so, we have to switch to using QCA-s QUIC repo instead of
Kalle-s.
QCA-s QUIC repo does not have BDF-s so we have to get the QCN9074 BDF from
Kalles repo.
Tested-by: Mireia Fernández Casals <meirin.f@gmail.com> # Xiaomi AX3600
Tested-by: Francisco G Luna <frangonlun@gmail.com> #Netgear WAX218
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adapts the engine build infrastructure to allow building providers,
and packages the legacy provider. Providers are the successors of
engines, which have been deprecated.
The legacy provider supplies OpenSSL implementations of algorithms that
have been deemed legacy, including DES, IDEA, MDC2, SEED, and Whirlpool.
Even though these algorithms are implemented in a separate package,
their removal makes the regular library smaller by 3%, so the build
options will remain to allow lean custom builds. Their defaults will
change to 'y' if not bulding for a small flash, so that the regular
legacy package will contain a complete set of algorithms.
The engine build and configuration structure was changed to accomodate
providers, and adapt to the new style of openssl.cnf in version 3.0.
There is not a clean upgrade path for the /etc/ssl/openssl.cnf file,
installed by the openssl-conf package. It is recommended to rename or
remove the old config file when flashing an image with the updated
openssl-conf package, then apply the changes manually.
An old openssl.cnf file will silently work, but new engine or provider
packages will not be enabled. Any remaining engine config files under
/etc/ssl/engines.cnf.d can be removed.
On the build side, the include file used by engine packages was renamed
to openssl-module.mk, so the engine packages in other feeds need to
adapt.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Engines that are built into the main libcrypto OpenSSL library can't be
disabled through UCI. Add a 'builtin' setting to signal that the engine
can't be disabled through UCI, and show a message explaining this in
case buitin=1 and enabled=0.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Building openssl with OPENSSL_SMALL_FOOTPRINT yelds only from 1% to 3%
decrease in size, dropping performance from 2% to 91%, depending on the
target and algorithm.
For example, using AES256-GCM with 1456-bytes operations, X86_64 appears
to be the least affected with 2% performance penalty and 1% reduction in
size; mips drops performance by 13%, size by 3%; Arm drops 29% in
performance, 2% in size.
On aarch64, it slows down ghash so much that I consider it broken
(-91%). SMALL_FOOTPRINT will reduce AES256-GCM performance by 88%, and
size by only 1%. It makes an AES-capable CPU run AES128-GCM at 35% of
the speed of Chacha20-Poly1305:
Block-size=1456 bytes AES256-GCM AES128-GCM ChaCha20-Poly1305
SMALL_FOOTPRINT 62014.44 65063.23 177090.50
regular 504220.08 565630.28 182706.16
OpenSSL 1.1.1 numbers are about the same, so this should have been
noticed a long time ago.
This creates an option to use OPENSSL_SMALL_FOOTPRINT, but it is turned
off by default unless SMALL_FLASH or LOW_MEMORY_FOOTPRINT is used.
Compiling with -O3 instead of -Os, for comparison, will increase size by
about 14-15%, with no measureable effect on AES256-GCM performance, and
about 2% increase in Chacha20-Poly1305 performance on Aarch64.
There are no Arm devices with the small flash feature, so drop the
conditional default. The package is built on phase2, so even if we
include an Arm device with small flash later, a no-asm library would
have to be built from source anyway.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
40ab806 config: use dedicated link local function to check interface
a84bff2 netlink: add support for getting interface linklocal
2ea065f Revert "config: recheck have_link_local on interface reload if already init"
4b38e6b config: fix feature for enabling service only when interface RUNNING
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some modems (namely, Telit LE910C4) require the IPv6 connection state to
be cleared explicitly, to avoid reporting "no effect" if IPv6
connection is already connected through autoconnect mechanism, or during
LTE default bearer attach, which would lead to established session, but
without a way to inform protocol handler of the status.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Some modems require CID to be set explicitly during IPv6 connection
status check, others require IPv6 address family to be checked explicitly
after establishing connection, in order to provide correct status.
Set both fields in the request to satisfy them.
Fixes: c8a88118af ("uqmi: set CID during 'query-data-status' operation")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Given ipv6 has SLAAC it is quite plausible to wish to use dynamic
dhcp4 but static dhcp6. This patch keeps dynamicdhcp as the default
option for both, but is overridden by dynamicdhcpv6 or dynamicdhcpv4
Signed-off-by: Ian Dall <ian@beware.dropbear.id.au>
The dhcphostsfile must be mounted into the (ujail) sandbox.
The file can not be accessed without this mount.
Signed-off-by: Ruben Jenster <rjenster@gmail.com>
Kmod-tg3 supports Ethernet adapters over PCIe bus. On targets without
PCI support, this package is empty. Symbol CONFIG_TIGON3 depends on
CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kmod-hfcpci and kmod-hfcmulti supports ISDN adapters over PCI. On targets
without PCI support, this package is empty. Symbol CONFIG_MISDN_HFCMULTI
and CONFIG_MISDN_HFCPCI depends on CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Changes:
1c6f0f3 libtraceevent: version 1.7.2
73f6a8a libtraceevent: Fix some missing commas in big endian blocks
da2ea6b libtraceevent: Rename "ok" to "token_has_paren" in process_sizeof()
e6f7cfa libtraceevent: No need for testing ok in else if (!ok) in process_sizeof()
a4b1ba5 libtraceevent: Fix double free in parsing sizeof()
Signed-off-by: Nick Hainke <vincent@systemli.org>
Recent ath11k sync introduced a regression causing 80+80 and 160MHz to
stop being advertised and thus not selectable due to the respective feature
flags being cleared.
So, until we get answers upstream to what was the reasoning behind this and
it gets fixed, lets just remove the flag clearing to reanable 160MHz.
Fixes: 789a0bac35 ("mac80211: ath11k: sync with ath-next")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use latest release build instead of a git snapshot. As this tarball
extracts in a trusted-firmware-a-2.8 subdirectory, we no longer need to
override the PKG_NAME defined in trusted-firmware-a.mk. The actual
package name is still the same, so we don't need to update any
dependencies.
Tested on A64-OLinuXino-1Ge16GW.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is the newest release where 210-sunxi-deactivate-binman.patch still
applies.
Tested on A64-Olinuxino-eMMC.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The Mikrotik R11e-LTE6 modem is similar to ZTE MF286R modem, added
earlier: it has a Marvel chip, able to work in ACM+RNDIS mode, knows ZTE
specific commands, runs OpenWrt Barrier Breaker fork.
While the modem is able to offer IPv6 address, the RNDIS setup is unable
to complete if there is an IPv6 adress.
While it works in ACM+RNDIS mode, the user experience isn't as good as
with "proto 3g": the modem happily serves a local IP (192.168.1.xxx)
without internet access. Of course, if the modem has enough time
(for example at the second dialup), it will serve a public IP.
Modifing the DHCP Lease (to a short interval before connect and back to
default while finalizing) is a workaround to get a public IP at the
first try.
A safe workaround for this is to excercise an offline script of the
pingcheck program: simply restart (ifdown - ifup) the connection.
Another pitfall is that the modem writes a few messages at startup,
which confuses the manufacturer detection algorithm and got disabled.
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (2366): Failed to parse message data
daemon.notice netifd: mikrotik (2366): WARNING: Variable 'ok' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2366): Unsupported modem
daemon.notice netifd: mikrotik (2426): Stopping network mikrotik
daemon.notice netifd: mikrotik (2426): Failed to parse message data
daemon.notice netifd: mikrotik (2426): WARNING: Variable '*simdetec:1,sim' does not exist or is not an array/object
daemon.notice netifd: mikrotik (2426): Unsupported modem
daemon.notice netifd: Interface 'mikrotik' is now down
A workaround for this is to use the "delay" option in the interface
configuration.
I want to thank Forum members dchard (in topic Adding support for
MikroTik hAP ac3 LTE6 kit (D53GR_5HacD2HnD)) [1]
and mrhaav (in topic OpenWrt X86_64 + Mikrotik R11e-LTE6) [2]
for sharing their experiments and works.
Another information page was found at eko.one.pl [3].
[1]: https://forum.openwrt.org/t/137555
[2]: https://forum.openwrt.org/t/151743
[3]: https://eko.one.pl/?p=modem-r11elte
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
The MikroTik R11e-LTE6 modem goes into flight mode (CFUN=4) at startup
and the radio is off (*RADIOPOWER: 0):
AT+RESET
OK
OK
*SIMDETEC:2,NOS
*SIMDETEC:1,SIM
*ICCID: 8936500119010596302
*EUICC: 1
+MSTK: 11, D025....74F3
*ADMINDATA: 0, 2, 0
+CPIN: READY
*EUICC: 1
*ECCLIST: 5, 0, 112, 0, 000, 0, 08, 0, 118, 0, 911
+CREG: 0
$CREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
+CGREG: 0
+CEREG: 0
+CESQ: 99,99,255,255,255,255
*CESQ: 99,99,255,255,255,255,0
*RADIOPOWER: 0
+MMSG: 0, 0
+MMSG: 0, 0
+MMSG: 1, 0
+MPBK: 1
While the chat script is able to establish the PPP connection,
it's closed instantly by the modem: LCP terminated by peer.
local2.info chat[7000]: send (ATD*99***1#^M)
local2.info chat[7000]: expect (CONNECT)
local2.info chat[7000]: ^M
local2.info chat[7000]: ATD*99***1#^M^M
local2.info chat[7000]: CONNECT
local2.info chat[7000]: -- got it
local2.info chat[7000]: send ( ^M)
daemon.info pppd[6997]: Serial connection established.
kern.info kernel: [ 453.659146] 3g-mikrotik: renamed from ppp0
daemon.info pppd[6997]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[6997]: Using interface 3g-mikrotik
daemon.notice pppd[6997]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.info pppd[6997]: LCP terminated by peer
daemon.notice pppd[6997]: Connection terminated.
daemon.notice pppd[6997]: Modem hangup
daemon.info pppd[6997]: Exit.
daemon.notice netifd: Interface 'mikrotik' is now down
Sending "AT+CFUN=1" to modem deactivates the flight mode and
solves the issue:
daemon.notice netifd: Interface 'mikrotik' is setting up now
daemon.notice netifd: mikrotik (7051): sending -> AT+CFUN=1
daemon.notice pppd[7137]: pppd 2.4.9 started by root, uid 0
local2.info chat[7140]: abort on (BUSY)
local2.info chat[7140]: abort on (NO CARRIER)
local2.info chat[7140]: abort on (ERROR)
local2.info chat[7140]: report (CONNECT)
local2.info chat[7140]: timeout set to 10 seconds
local2.info chat[7140]: send (AT&F^M)
local2.info chat[7140]: expect (OK)
local2.info chat[7140]: ^M
local2.info chat[7140]: +CESQ: 99,99,255,255,255,255^M
local2.info chat[7140]: ^M
local2.info chat[7140]: *CESQ: 99,99,255,255,255,255,0^M
local2.info chat[7140]: AT&F^MAT&F^M^M
local2.info chat[7140]: OK
local2.info chat[7140]: -- got it
...
local2.info chat[7140]: send (ATD*99***1#^M)
local2.info chat[7140]: expect (CONNECT)
local2.info chat[7140]: ^M
local2.info chat[7140]: ATD*99***1#^M^M
local2.info chat[7140]: CONNECT
local2.info chat[7140]: -- got it
local2.info chat[7140]: send ( ^M)
daemon.info pppd[7137]: Serial connection established.
kern.info kernel: [ 463.094254] 3g-mikrotik: renamed from ppp0
daemon.info pppd[7137]: Renamed interface ppp0 to 3g-mikrotik
daemon.info pppd[7137]: Using interface 3g-mikrotik
daemon.notice pppd[7137]: Connect: 3g-mikrotik <--> /dev/ttyACM0
daemon.warn pppd[7137]: Could not determine remote IP address: defaulting to 10.64.64.64
daemon.notice pppd[7137]: local IP address 100.112.63.62
daemon.notice pppd[7137]: remote IP address 10.64.64.64
daemon.notice pppd[7137]: primary DNS address 185.29.83.64
daemon.notice pppd[7137]: secondary DNS address 185.62.131.64
daemon.notice netifd: Network device '3g-mikrotik' link is up
daemon.notice netifd: Interface 'mikrotik' is now up
To send this AT command to the modem the "runcommand.gcom" script
dependency is moved from comgt-ncm to comgt.
As the comgt-ncm package depends on comgt already, this change
is a NOOP from that point of view.
But from the modem's point it is a low hanging fruit as the modem
is usable with installing comgt and kmod-usb-ncm packages.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
This patch solves the problem of receiving "error" responses when
initially calling gcom. This avoids unnecessary NO_DEVICE failures.
A retry loop retries the call after an "error" response within the
specified delay. A successful response will continue with the connection
immediately without waiting for max specified delay, bringing the
interface up sooner.
Signed-off-by: Mike Wilson <mikewse@hotmail.com>
ccd7e46 ipq40xx: add support for Wallystech DR40x9
2ce60e1 Revert "ipq40xx: add support for Wallystech DR40x9"
ea962ca ipq40xx: add Emplus WAP551 BDF
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
General specification:
SoC Type: MediaTek MT7620N (580MHz)
ROM: 8 MB SPI-NOR (W25Q64FV)
RAM: 64 MB DDR (EM6AB160TSD-5G)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Buttons: 3 button (POWER, RESET, WPS)
Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT)
Bootloader: U-Boot 1.1.3
Power: 9 VDC, 0.6 A
MAC in stock:
|- + |
| LAN | RF-EEPROM + 0x04 |
| WLAN | RF-EEPROM + 0x04 |
| WAN | RF-EEPROM + 0x28 |
OEM easy installation
1. Use a PC to browse to http://my.keenetic.net.
2. Go to the System section and open the Files tab.
3. Under the Files tab, there will be a list of system
files. Click on the Firmware file.
4. When a modal window appears, click on the Choose File
button and upload the firmware image.
5. Wait for the router to flash and reboot.
OEM installation using the TFTP method
1. Download the latest firmware image and rename it to
klite3_recovery.bin.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the
firmware image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect
the PC to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address
192.168.1.2 and subnet mask 255.255.255.0.
5. Power up the router while holding the reset button pressed.
6. Wait approximately for 5 seconds and then release the
reset button.
7. The router should download the firmware via TFTP and
complete flashing in a few minutes.
After flashing is complete, use the PC to browse to
http://192.168.1.1 or ssh to proceed with the configuration.
Signed-off-by: Alexey Bartenev <41exey@proton.me>
This board is very similar to the Aruba AP-105, but is
outdoor-first. It is very similar to the MSR2000 (though certain
MSR2000 models have a different PHY[^1]).
A U-Boot replacement is required to install OpenWrt on these
devices[^2].
Specifications
--------------
* Device: Aruba AP-175
* SoC: Atheros AR7161 680 MHz MIPS
* RAM: 128MB - 2x Mira P3S12D40ETP
* Flash: 16MB MXIC MX25L12845EMI-10G (SPI-NOR)
* WiFi: 2 x DNMA-H92 Atheros AR9220-AC1A 802.11abgn
* ETH: IC+ IP1001 Gigabit + PoE PHY
* LED: 2x int., plus 12 ext. on TCA6416 GPIO expander
* Console: CP210X linking USB-A Port to CPU console @ 115200
* RTC: DS1374C, with internal battery
* Temp: LM75 temperature sensor
Factory installation:
- Needs a u-boot replacement. The process is almost identical to that
of the AP105, except that the case is easier to open, and that you
need to compile u-boot from a slightly different branch:
https://github.com/Hurricos/u-boot-ap105/tree/ap175
The instructions for performing an in-circuit reflash with an
SPI-Flasher like a CH314A can be found on the OpenWrt Wiki
(https://openwrt.org/toh/aruba/ap-105); in addition a detailed guide
may be found on YouTube[^3].
- Once u-boot has been replaced, a USB-A-to-A cable may be used to
connect your PC to the CP210X inside the AP at 115200 baud; at this
point, the normal u-boot serial flashing procedure will work (set up
networking; tftpboot and boot an OpenWrt initramfs; sysupgrade to
OpenWrt proper.)
- There is no built-in functionality to revert back to stock firmware,
because the AP-175 has been declared by the vendor[^4] end-of-life
as of 31 Jul 2020. If for some reason you wish to return to stock
firmware, take a backup of the 16MiB flash before flashing u-boot.
[^1]: https://github.com/shalzz/aruba-ap-310/blob/master/platform/bootloader/apboot-11n/include/configs/msr2k.h#L186
[^2]: https://github.com/Hurricos/u-boot-ap105/tree/ap175
[^3]: https://www.youtube.com/watch?v=Vof__dPiprs
[^4]: https://www.arubanetworks.com/support-services/end-of-life/#product=access-points&version=0
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
When forwarding is set to 0, frames are typically sent with ttl=1.
Move the ttl decrement check below the check for local receive in order to
fix packet drops.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
I found use for this in my scripts; I noticed that it is already
compiled with util-linux - there just isn't package for it -
let's package it then.
Description:
The rev utility copies the specified files to the standard output,
reversing the order of characters in everyline.
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
Ruckus ZoneFlex 7363 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point. ZoneFlex 7343 is the single band variant of 7363
restricted to 2.4GHz, and ZoneFlex 7341 is 7343 minus two Fast Ethernet
ports.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet 1: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Ethernet 2: two Fast Ethernet ports through Realtek RTL8363S switch,
connected with Fast Ethernet link to CPU.
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the -U variants.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single PH1 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed.
Use the Gigabit interface, Fast Ethernet ports are not supported
under U-boot:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7363-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7363_fw_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7363-squashfs-sysupgrade.bin
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7363_backup.bin
4. System will reboot.
Quirks and known issues:
- Fast Ethernet ports on ZF7363 and ZF7343 are supported, but management
features of the RTL8363S switch aren't implemented yet, though the
switch is visible over MDIO0 bus. This is a gigabit-capable switch, so
link establishment with a gigabit link partner may take a longer time
because RTL8363S advertises gigabit, and the port magnetics don't
support it, so a downshift needs to occur. Both ports are accessible
at eth1 interface, which - strangely - runs only at 100Mbps itself.
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Ruckus ZoneFlex 7351 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the 7351-U variant.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7351-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7351_fw_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7351-squashfs-sysupgrade.bin
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7351_backup.bin
4. System will reboot.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
7c0f603 router: skip RA and wait for LINK-LOCAL to be assigned
ba30afc config: skip interface setup if interface not IFF_RUNNING
06b111e Revert "odhcpd: Reduce error messages"
90d6cc9 odhcpd: Reduce error messages
Also drop AUTORELEASE since it got deprecated.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
SSDK is doing everything custom, so trying to use mold and/or LTO
fails, so lets opt-out of using both of them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
[a.heider: split and switch to PKG_BUILD_FLAGS]
Signed-off-by: Andre Heider <a.heider@gmail.com>
This reduces open coding and allows to easily add a knob to enable
it treewide, where chosen packages can still opt-out via "no-lto".
Some packages used LTO, but not the linker plugin. This unifies 'em
all to attempt to produce better code.
Quoting man gcc(1):
"This improves the quality of optimization by exposing more code to the
link-time optimizer."
Also use -flto=auto instead of -flto=jobserver, as it's not guaranteed
that every buildsystem uses +$(MAKE) correctly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This reduces open coding and allows to easily add a knob to
enable it treewide, where chosen packages can still opt-out via
"no-gc-sections".
Note: libnl, mbedtls and opkg only used the CFLAGS part without the
LDFLAGS counterpart. That doesn't help at all if the goal is to produce
smaller binaries. I consider that an accident, and this fixes it.
Note: there are also packages using only the LDFLAGS part. I didn't
touch those, as gc might have been disabled via CFLAGS intentionally.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Adds support for the Wallys DR40x9 series boards.
They come in IPQ4019 and IPQ4029 versions.
IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures.
Specifications are:
* CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz
* RAM: 512 MB
* Storage: 2MB of SPI-NOR, 128 MB of parallel NAND
* USB 3.0 TypeA port for users
* MiniPCI-E with PCI-E 2.0 link
* MiniPCI-E for LTE modems with only USB2.0 link
* 2 SIM card slots that are selected via GPIO11
* MicroSD card slot
* Ethernet: 2x GBe with 24~48V passive POE
* SFP port (Does not work, I2C and GPIO's not connected on hardware)
* DC Jack
* UART header
* WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac
* 4x MMCX connectors for WLAN
* Reset button
* 8x LED-s
Installation instructions:
Connect to UART, pins are like this:
-> 3.3V | TX | RX | GND
Settings are 115200 8n1
Boot initramfs from TFTP:
tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb
bootm
Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name>
The board file binary was provided from Wallystech on March 14th 2023
including full permission to use and distribute.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall
or ceiling mountable. It can be powered via PoE, or a 12 V adapter.
The board has footprints for 2.54mm UART headers. They're difficult to
solder because the GND is connected to a large copper plane. Only try
soldering if you are very skilled. Otherwise, use pogo pins.
Specifications:
---------------
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 366 MB of RAM available to OS, not sure of total amount
* Storage: Macronix MX30UF2G18AC 256MB NAND
* Ethernet:
* 2.5G RJ45 port (QCA8081) with PoE input
* WLAN:
* 2.4GHz/5GHz with 8 antennas
* LEDs:
* Power (Amber)
* LAN (Blue)
* 2G WLAN (Blue)
* 5G WLAN (Blue)
* Buttons:
* 1x Factory reset
* Power: 12V DC Jack
* UART: Two 4-pin unpopulated headers near the LEDs
* "J2 UART" is the CPU UART, 3.3 V level
Installation:
=============
Web UI method
-------------
Flashing OpenWRT using the vendor's Web UI is problematic on this
device. The u-boot mechanism for communicating the active rootfs is
antiquated and unreliable. Instead of setting the kernel commandline,
it relies on patching the DTS partitions of the nand node. The way
partitions are patched is incompatible with newer kernels.
Newer kernels use the SMEM partition table, which puts "rootfs" on
mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One
reliable way to boot from mtd14 and avoid boot loops is to use an
initramfs image.
1. In the factory web UI, navigate to System Manager -> Firmware.
2. In the "Local Firmware Upgrade" section, click Browse
3. Navigate and select the 'web-ui-factory.fit' image
4. Click "Upload"
5. On the following page, click on "Proceed"
The flash proceeds at this point and the system will reboot
automatically to OpenWRT.
6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline
SSH method
----------
Enable SSH using the CLI or Web UI. The root account is locked out to
ssh, and the admin account defaults to Netgear's CLI application.
So we need to get creative:
First, make sure the device boots from the second firmware partition:
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 1
Then reboot the device, and run the update:
scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \
-o hostkeyalgorithms=ssh-rsa \
netgear_wax218-squashfs-nand-factory.ubi \
admin@<ipaddr>:/tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 0
Now reboot the device, and it should boot into a ready-to-use OpenWRT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
This brings in actually setting the MU-MIMO parameters in HW and 6GHz
regulatory support along with some minor resource handling fixes.
This allows to easily backport further fixes as cherry picking them has
started requiring manual conflict resolution.
Signed-off-by: Robert Marko <robimarko@gmail.com>
31ff96d ipq806x: add support for Nokia Airscale AC400i
1af1df2 ath11k: ipq8074: add Netgear WAX218
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
This splits the code in 4 files:
- uencrypt.h
- uencrypt.c - main program
- uencrypt-openssl.c - OpenSSL/wolfSSL implementation
- uencrypt-mbedtls - mbedTLS implementation
Other changes, accounting for ~400 bytes increase in ipk size:
- more error condition checking and reporting,
- hide key and iv command line arguments
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit includes some additional changes:
- better handling of iv and keys in openssl/wolfssl variants
- fix compiler warnings and whitespace
- build all 3 variants as separate packages
- adjust the new package name in targets' DEVICE_PACKAGES
- remove PKG_FLAGS:=nonshared
[Beeline SmartBox Flash - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
[after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
d978830 rc: add option to get info for a single script in list method
632b4fc rc: add option to skip running check for list method
5577db9 rc: add support for scanning USE_PROCD and skip running if not supported
4de3f02 rc: fix and improve script scanning START and STOP
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Source BDF files out of project dedicated repository and drop local file
from openwrt main repository.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
odhcp6c logs messages related to its activity when invoked with -v, but
there is no way to configure this from within OpenWrt. This adds a UCI
option to turn on odhcp6c logging, disabled by default. To enable, set,
for example, network.wan6.verbose = 1.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
This fixes a build problem on some targets.
Fixes: 3e9005546a ("kernel: modules: package Microchip LAN743x PCIe gigE driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Deactivate the msgpack option. The binutils build might detect the
libmsgpackc.so.2 library and will try to link against it, if it is not
explicitly deactivated.
This prevents the following build errors seen in the build bots.
Package binutils is missing dependencies for the following libraries:
libmsgpackc.so.2
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
SoC: Freescale P1010
RAM: 512MB
FLASH: 1 MB SPI-NOR
512 MB NAND
ETH: 3x Gigabite Ethernet (Atheros AR8033)
SERIAL: Cisco RJ-45 (115200 8N1)
RTC: Battery-Backed RTC (I2C)
Installation
------------
1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI
programmer. The SHA1 hash for the U-Boot password is currently
unknown.
A tool for patching U-Boot is available at
https://github.com/blocktrron/t10-uboot-patcher/
You can also patch the unknown password yourself. The SHA1 hash is
E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA
2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears.
The patched password is '1234' (without quotation marks)
3. Download the OpenWrt initramfs image. Copy it to a TFTP server
reachable at 10.0.1.13/24 and rename it to uImage.
4. Connect the TFTP server to ethernet port 0 of the Watchguard T10.
5. Download and boot the initramfs image by entering "tftpboot; bootm;"
in U-Boot.
6. After OpenWrt booted, create a UBI volume on the old data partition.
The "ubi" mtd partition should be mtd7, check this using
$ cat /proc/mtd
Create a UBI partition by executing
$ ubiformat /dev/mtd7 -y
7. Increase the loadable kernel-size of U-Boot by executing
$ fw_setenv SysAKernSize 800000
8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using
scp. Install the image by using sysupgrade:
$ sysupgrade -n <path-to-sysupgrade>
Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might
have to change the ethernet-port.
9. OpenWrt should now boot from the internal NAND. Enjoy.
Signed-off-by: David Bauer <mail@david-bauer.net>
This allows adding backup servers, in case the primary ones fail.
Assume that port and shared secret are going to be the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the trivial abscence of $() when assigning engine config files to
the main libopenssl-config package even if the corresponding engines
were not built into the main library.
This is mostly cosmetic, since scripts/ipkg-build tests the file's
presence before it is actually included in the package's conffiles.
Fixes: 30b0351039 "openssl: configure engine packages during install"
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The bump to 3.0.8 inadvertently removed patches that are needed here,
but were not adopted upstream. The most important one changes the
default value of the DIGESTS setting from ALL to NONE. The absence of
this patch causes a sysupgrade failure while the engine is in use with
digests enabled. When this happens, the system fails to boot with a
kernel panic.
Also, explicitly set DIGESTS to NONE in the provided config file, and
change the default ciphers setting to disable ECB, which has been
recommended for a long time and may cause trouble with some apps.
The config file change by itself is not enough because the config file
may be preserved during sysupgrade.
For people affected by this bug:
You can either:
1. remove, the libopenssl-devcrypto package
2. disable the engine in /etc/config/openssl;
3. change /etc/ssl/engines.cnf.d/devcrypto.cnf to set DIGESTS=NONE;
4. update libopenssl-devcrypto to >=3.0.8-3
However, after doing any of the above, **you must reboot the device
before running sysupgrade** to ensure no running application is using
the engine. Running `/etc/init.d/openssl restart` is not enough.
Fixes: 7e7e76afca "openssl: bump to 3.0.8"
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
binutils 2.39: https://lists.gnu.org/archive/html/info-gnu/2022-08/msg00002.html
binutils 2.40: https://lists.gnu.org/archive/html/info-gnu/2023-01/msg00003.html
This version includes a new libsframe.so library, pack it into the
libbfd package as it is used by this library. Also deactivate some
optional configuration options for now.
An extra patch to fix compile problem in AARCH64 is added.
gprofng needs a C++ standard library, deactivate it for now.
Activate feature-disassembler-init-styled in bpftools too to fix
compilation with the updated binutils.
An bpftool version 7.0 or later is needed for binutils 2.39 and later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
bpftool changelog: https://github.com/libbpf/bpftool/releases
libbpf changelog: https://github.com/libbpf/libbpf/releases
This updates the bfptool to version 7.1.0. This also includes an update
of the libbpf to version 1.1.
This also adds some new feature options and removes some old ones which
were also removed form the source code. zlib for example is now
mandatory.
Add -flto also to LD flags to make it really work.
Before this change bpftool was on a git commit between version 6.7 and
6.8 and libbpf was on a commit between version 0.7 and 0.8.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
in kernel 5.17, fcd09c90c3c5254b18ef34e30c57c65d34290a84 integrated it
better with thee random framework.
Gives boot time randomness on supported devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
