mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 14:13:16 +00:00
4d79a65d60
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports. The majority of the code is based on @jewwest's PR #11830. Specifications: * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2) * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA) * Ethernet: 4x 10/100/1000 Mbps LAN, 1x 10/100/1000 Mbps WAN (Qualcomm QCA8075), 1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY) * Wi-Fi: * 2.4 GHz: Qualcomm QCN5024 4x4 * 2x 5 GHz: Qualcomm QCN5054 4x4 * USB: 2x USB 3.0 * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8 * Power: 19 VDC, 3.1 A Installation: * Flashing OpenWrt is done in two steps: a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-). This writes an initramfs based OpenWrt image onto the RAX120v2 b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline * U-Boot allows booting an initramfs image via TFTP: - Set ip of your PC to 192.168.1.100 - At the serial console interrupt boot at "Hit any key to stop autoboot:" - In u-boot run `tftpsrv` - On your PC send the OpenWrt initramfs image: tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb Make 5G Aquantia phy work: For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in u-boot by writing the firmware to the correct mtd partition. The firmware file found in the Netgear stock firmware under /lib/firmware/ named 'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to be converted to a MBN file. The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source, under 'git_home/u-boot.git/tools/mkheader.py' Convert the CLD file to MBN using: $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn This MBN file can then be flashed to the MTD partition to be used by u-boot. The necessary files can also be found in https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware * Write MBN file to MTD partition to be loaded automatically by u-boot: U-boot automatically tries to load the firmware from nand at address 0x7e00000 which corresponds to `/dev/mtd25` in OpenWrt. - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25) $ fgrep -i 'ethphyfw' /proc/mtd mtd25: 00080000 00020000 "ethphyfw - copy mbn file to /tmp/ folder of the router $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/ - write mbn file to ethphyfw partition $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References to RAX120v2 GPL source: https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com> |
||
|---|---|---|
| .. | ||
| base-files | ||
| boot | ||
| devel | ||
| firmware | ||
| kernel | ||
| libs | ||
| network | ||
| system | ||
| utils | ||
| Makefile | ||