The NIC router used to send an ICMP "Destination Unreachable" packet as
response to every unroutable IPv4 packet. However, RFC 1812 section 4.3.2.7
defines certain properties that must be fullfilled by an incoming packet in
order to be answered with this type of ICMP. One requirement is that the packet
is no IPv4 multicast.
This commit prevents sending the mentioned ICMP response for unroutable IPv4
multicasts and instead drops them silently.
Fixes#4563
Instead of having a generic "virt_qemu" board use "virt_qemu_<arch>" in
order to have a clean distinction between boards. Current supported
boards are "virt_qemu_arm_v7a", "virt_qemu_arm_v8a", and
"virt_qemu_riscv".
issue #4034
The NIC router used to add the DNS servers field to DHCP replies regardless of
whether there were DNS servers or not. As reported by a Genode user, the empty
DNS server field irritated at least Windows 10 guests (Vbox 6) that connected
to the NIC router. This resulted in Windows 10 ignoring DHCP offers from the
router with such characteristic.
With this commit adding the DNS server DHCP option is skipped if there are no
DNS servers at the corresponding DHCP server or the domain IP config the server
shall fetch its DNS servers from.
Fixes#4581
Provide additional PCI register information inside the pci-config part
of the devices ROM for clients able to access an Intel graphic card,
namely the GMCH control register content, which contains for instance
the GTT size and stolen memory size.
Ref genodelabs/genode#4578
Implement BIOS handover and Intel resume register update
apart from device driver to circumvent export of PCI
config space to drivers.
Ref genodelabs/genode#4578
The pci_decode has to extract the additional fields from the PCI configuration
space. The platform driver again has to parse and forward the knowledge too.
The PCI BAR indices are exported when info="yes" is set in the policy node for
the corresponding session.
Fixgenodelabs/genode#4577
The base address of I/O ports has a different encoding than
those of I/O memory. This needs to be encountered in the PCI
config helper utilities.
Fixgenodelabs/genode#4576
On okl4, pistachio, sel4 the test didn't come up fast enough in order to still
experience the first configuration of NIC router #1. This commit doubles the
lifetime of the first configuration of NIC router #1 to 4 seconds and raises
the overall test timeout accordingly.
Ref #4555
In overload situations, i.e. when a sender fills up the entire buffer, we land
in situations where the sender receives an ack_avail signal, releases one
packet, allocates and sends a packet and fails to allocate a second packet.
This is especially relevant if the receiver does not batch ack_avail signals
(such as vfs_lwip). In those ping-pong scheduling scenarios, the overhead from
catching the Packet_alloc_failed exception becomes significant. In case of the
NIC router, we will land in an overload situation if the sender is faster than
the receiver. The packet buffer will be filled up at some point and the NIC
router starts to drop packets. For every dropped packet, we currently have to
catch the Packet_alloc_failed exception.
This commit adds a new method alloc_packet_attempt to Packet_stream_source that
has almost the same signature as the older alloc_packet method but returns
an Attempt<Packet_descriptor, Alloc_packet_error> object. As the method already
used the allocator back end exception-less, changes on lower levels were not
needed. Furthermore, the NIC router was modified to use the new exception-less
alloc_packet_attempt instead of alloc_packet.
Ref #4555
Replaces the former implementation of the 'find_by_ip' method at the data
structure for ARP cache entries. This method used to return a reference to the
found object and threw an exception if no matching object was found.
The new implementation doesn't return anything and doesn't throw exceptions. It
takes two lambda arguments instead. One for handling the case that a match was
found with a reference to the matching object as argument and another for
handling the case that no object matches.
This way, expensive exception handling can be avoided and object references
stay in a local scope.
Ref #4555
According to a benchmarking series on Zynq (base-hw) and x260 (base-nova) using
test-nic_perf_router, increasing the 'max_packets_per_signal' has a significant
effect on the packet throughput. By increasing the default value from 32
to 150, we could gain a few hundred Mbit/s. Increasing the value further
does not seem to have such a strong effect, though.
genodelabs/genode#4555
The checksums for forwarded/routed UDP, TCP and ICMP, used to be always
re-calculated from scratch in the NIC router although the router changes only
a few packet fields. This commit replaces the old approach whereever sensible
with an algorithm for incremental checksum updates suggested in RFC 1071.
The goal is to improve router performance.
Ref #4555
The checksums for forwarded/routed IPv4, used to be always re-calculated from
scratch in the NIC router although the router changes only a few packet fields.
This commit replaces the old approach whereever sensible with an algorithm for
incremental checksum updates suggested in RFC 1071. The goal is to improve
router performance.
Ref #4555
We used to use 'unsigned long' for the accumulating variable when calculating
internet checksums. However, 'signed long' is more in accordance with RFC 1071
and will allow us to share the same back end for folding, once we implement
incremental updating of internet checksums.
Ref #4555
Prevent public reflection of the only internally used 'init_sum' argument in
'uint16_t internet_checksum(...)' that, in addition, added a default value to
the function interface.
Ref #4555
When sending an ICMP ECHO reply, the router merely swaps SRC and DST of the
IPv4 header of the corresponding request and these changes cancel each other
out in checksum calculation. Therefore, with this commit, the router skips
updating the IPv4 checksum in this context.
Ref #4555
The router used to update IPv4 checksums when routing via an <ip> rule
despite the fact that it doesn't change any IPv4 header fields in this case.
Ref #4555
The NIC router used to update IPv4 and layer 4 checksums of a packet for each
interface it was sent to (say, all interfaces of the domain the packet was
routed to). However, there was and is no technical reason for not doing it
only once and then iterating over the interfaces with the already updated
packet. This is what this commit does in an intent to raise the router's
performance.
Ref #4555
The NIC router uses the timer for relatively coarse-grained timeouts.
It therefore suffices to update and store the current time when the NIC router
is signalled and use the cached time instead. This prevents frequent
syscalls or RPCs when acquiring the current time for every packet.
genodelabs/genode#4555
The link dissolve timeout is updated for every packet, which leads to
trigger_once() RPCs that only marginally change the scheduled timeout but
significantly slow down the packet throughput.
genodelabs/genode#4555
The wakeup call only emits a single signal as it assumed both are
handled by the same signal handler. However, the original implementation
did not reset the wakeup_needed variable properly.
genodelabs/genode#4555
When using signal batching, ack_avail and packet_avail should always
be emitted and preferred over ready_to_submit and ready_to_ack.
A signal receiver might decide to not register the ready_to_* signals when it
handles congestion by dropping packets. The Nic router is an example of
such a signal receiver.
genodelabs/genode#4555
Using the 'query_buffer_ppgtt()' function allows for retrieving the
virtual address of the buffer in the PPGTT.
This is for components that manage the GPU virtual addresses rather than
the client as is the case with the lima driver.
Issue #4559.
The parent-provides model is destroyed if no <parent-provides> node is
found in the configuration, which resulted in
Warning: list model not empty at destruction time
and leaking memory for the allocated nodes. The commit now explicitly
empties the list model in the destructor of ~Parent_provides_model.
Note, the case is implicitly tested in pkg/test-init by step "denial of
forwarded session request" and <init_config version="empty">.
Thanks to Peter for reporting this issue.
Fixes#4547
Whenever a domain looses all its interfaces or the link state of all attached
interfaces is down at once, the domain potentially moves to another Ethernet
segment and should therefore consider its ARP cache to be outdated.
RFC 826 states that "... If a host moves, any connections initiated by that
host will work, assuming its own address resolution table is cleared when it
moves. ...".
Therefore, this commit introduces clearing the ARP cache and the initially
stated events.
This commit was motivated by an issue with the PinePhone Modem and USB NIC.
On the PinePhone, the Modem has its own OS and acts as direct gateway to the
outer world for the USB NIC that is driven by Genode. However, whenever the
Modem gets restarted, Modem and USB NIC receive a new MAC address. This used
to conflict with the NIC routers ARP entry for the Modem that didn't cease to
be valid.
With this commit, the integrator of such a scenario at least has a convenient
way of fixing this by ensuring that all interfaces at the USB NIC domain go
down when resetting (e.g. by ensuring that the USB NIC is the only interface at
that domain).
Fixes#4558
Replaces the former use of the 'find_by_name' method of the AVL string tree.
This method returned a reference to the found object and threw an exception if
no matching object was found.
The locally implemented replacement doesn't return anything and doesn't throw
exceptions. It takes two lambda arguments instead. One for handling the case
that a match was found with a reference to the matching object as argument and
another for handling the case that no object matches.
This way, expensive exception handling can be avoided and object references
stay in a local scope.
Furthermore, this commit modifies the local wrapper for the insert method of
the AVL string tree, so, that it follows the above mentioned concept as well.
Ref #4536
Replaces the former implementation of the 'find_by_domain' method at the data
structure for NAT rules. This method used to return a reference to the found
object and threw an exception if no matching object was found.
The new implementation doesn't return anything and doesn't throw exceptions. It
takes two lambda arguments instead. One for handling the case that a match was
found with a reference to the matching object as argument and another for
handling the case that no object matches.
This way, expensive exception handling can be avoided and object references
stay in a local scope.
Ref #4536
Replaces the former implementation of the 'find_by_port' method at the data
structure for permit rules. This method used to return a reference to the found
object and threw an exception if no matching object was found.
The new implementation doesn't return anything and doesn't throw exceptions. It
takes two lambda arguments instead. One for handling the case that a match was
found with a reference to the matching object as argument and another for
handling the case that no object matches.
This way, expensive exception handling can be avoided and object references
stay in a local scope.
Furthermore, the commit introduces a convenience wrapper for finding the best
matching pair of transport rule and corresponding permit rule for a given
destination IP and port. This method as well follows the above mentioned
concept.
Ref #4536
Replaces the former implementation of the 'find_longest_prefix_match' method at
the data structure for direct rules. This method used to return a reference to
the found object and threw an exception if no matching object was found.
The new implementation doesn't return anything and doesn't throw exceptions. It
takes two lambda arguments instead. One for handling the case that a match was
found with a reference to the matching object as argument and another for
handling the case that no object matches.
This way, expensive exception handling can be avoided and object references
stay in a local scope.
Ref #4536
Replaces the former implementation of the 'find_longest_prefix_match' method at
the data structure for direct rules. This method used to return a reference to
the found object and threw an exception if no matching object was found.
The new implementation doesn't return anything and doesn't throw exceptions. It
takes two lambda arguments instead. One for handling the case that a match was
found with a reference to the matching object as argument and another for
handling the case that no object matches.
This way, expensive exception handling can be avoided and object references
stay in a local scope.
Ref #4536
Replaces the former implementation of find_by_id at the data structure for
links. This method used to return a reference to the found object and threw an
exception if no matching object was found.
The new implementation doesn't return anything and doesn't throw exceptions. It
takes two lambda arguments instead. One for handling the case that a match was
found with a reference to the matching object as argument and another for
handling the case that no object matches.
This way, expensive exception handling can be avoided and object references
stay in a local scope.
Ref #4536
Just add riscv spec files. The riscv versions should use MMIO transport
as ARM versions do. They also should work fine for riscv_qemu machine
from genode-riscv repository.
acpica and the Intel display driver tries to use the Intel Opregion
simultaneously on Genode, which is not supported nor wanted for IO_MEM region as
which it is handled.
Attempts to remove the access to the region was not successful, since some
SSDT table contains ACPI AML code which is executed regularly and read/write
the Opregion.
The patch adds support to make a copy of the Intel Opregion and report it as
is. The copy was sufficient to make the Intel display driver working to find
and lookup the Intel VBT (video bios table) information to setup all
connectors on a Fujitsu U7411 docking station.
Issue #4531
ACPICA needs access to the host bridge 0:0.0 on Intel, which is also
accessed by the Intel display driver. Since for the Intel display driver the
PCI device is specified in the policy explicitly, the PCI device is filtered
out for the ACPICA driver which uses the policy "ALL".
Issue #4532
As accommodating the session component object is already taken care of
be the root component implementation, remove the remaining redundant
checks.
Fixes#4521.
There is a race between the trace subject doing the buffer
initialization and the monitor trying to iterate the buffer entries. If
the monitor tries to iterate entries of an uninitialized buffer, it will
read the very first entry twice. The monitor should therefore only start
iteration when the buffer has been initialised.
genodelabs/genode#4513
The hover state is evaluated for the routing of input events. When
routing a touch event, the decision should be based on the most recently
observed touch position. Without this patch, however, the hover state kept
referring to the initial pointer position (screen center) in the absence
of any other motion events.
Issue #4514
* Adds methods for copying raw data to the data field of Ethernet frames and
UDP packets. This is used in the port to wrap the higher-layer packet data
prepared by the contrib code with the additionally required headers before
sending it at a network session.
* Adds a method to cast raw data to an IPv4 packet. This is required in the
port in order to check values in stand-alone IP packets produced by the
contrib code before sending them at a network session.
* Adds methods for setting UDP ports given big endian port values without
having to convert to little endian in the app and then back to big endian in
the net lib.
Ref #4397
* Some fixups for the README
* Make config ROM const when used for the session policies
* Turn Reporter into Expanding_reporter
* Always first register ROM signal handler before parsing it the first time
Outsource parts of the Main object into a common compound object,
common parts of the Makefile description and depot source package.
Fixgenodelabs/genode#4503
* Parse PCI specific information from devices ROM
* Enable DMA, I/O memory and I/O port access dependent on BARs in config space
* Introduce device PD for Nova + IOMMU support
* Enable MSIs if available
* Add PCI specific policy rules
Fixesgenodelabs/genode#4502
Instead of returning an invalid device capability when a device
is (not yet) available, e.g. a PCI device is requested before the
PCI bus got parsed accordingly, we check the device capability
within the Platform::Connection utilities, and register temporarily
an Io_signal_handler to wait for changes of the devices ROM, and
try the device aquisition again. Thereby, simple drivers so not have
to take the burden to do so.
To enable this feature for all drivers, we always have to export a
devices ROM, but limit the information about physical resources
(I/O memory addresses, IRQ numbers, I/O port ranges) to clients with
'info=yes' in their policy description.
Fixgenodelabs/genode#4496
By adding a 'report' node to the platform driver's configuration
one can enable either devices or config reports. The devices
report contains all devices and their detailed state, as well as
whether it is already in use or not. The config report contains
one by one the current configuration of the platform driver.
Moreover, this commit adds a README file describing the facilities
of the platform driver.
Fixgenodelabs/genode#4386
If PCI devices happen to miss complete configuration after boot, the
platform driver supports <pci-fixup> nodes for concrete devices
(specified by bus-device-functions tuples). The
<bar> node instructs the platform driver to remap BAR id 0 to address
0x4017002000, which amends the BIOS configuration and is stringently
required for BARs with address 0.
! <pci-fixup bus="0" device="0x15" function="3">
! <bar id="0" address="0x4017002000"/>
! </pci-fixup>
The issue was discovered with Intel LPSS devices in Fujitsu notebooks.
Fixes#4501
To discharge the generic platform driver from certain PCI bus scanning,
and ACPI + kernel specifics, this commit introduces a new component,
which consumes the acpi drivers report and the platform_info from core
to prepare a devices ROM for the platform driver that contains all
PCI devices and its resources.
Fixgenodelabs/genode#4495
USB Attached SCSI devices might expose a bulk-only interface
as fall-back at interface 0 and alternate setting 0. This commit
allows for probing all alternate settings of the active interface
to be able to use such devices.
The configuration was extended so that in case the device interface
is known beforehand the driver can be configured accordingly.
Fixes#4494.
Since the driver relies on all requests being Nvme::MPS_LOG2 aligned
as advertised in its Block::Info the added check will reject any
misaligned requests (using 'gpt_write' led to an IOMMU write fault).
Issue #4486.
To signal that a device gets used and released by a session
introduce claim, release, and release all callbacks in the
USB interface of the C-API.
Ref genodelabs/genode#4483
This patch changes the meaning of the 'offset' parameter of the
'produce_write_content' and 'consume_read_result' hook functions.
The value used to reflect the absolute byte position but in practice,
a job-relative byte offset is desired.
Issue #4474
Before this commit, the block-request handler was implemented as
Io_signal_handler and, additionally, the USB driver called the
block-request handler on request completion directly on I/O level. This
is generally a bad idea because I/O handlers should avoid to have direct
global side effects. In contrast, application logic should be
implemented in way that it consumes atomic state changes after I/O
completed. Now USB I/O completion locally submits a signal to the
block-request Signal_handler.
The Uplink_test used to end in an uncaucht exception about a failed packet
allocation on several x86_32 platforms.
* Destruct and re-construct the corresponding TX packet allocator during a
link-down-up step in the Uplink test. Fixes the exceptions but results in a
never ending test.
* Decouple the link-down-up steps from the handling of packet stream signals
by simply triggering it with a local periodic timeout of 1 sec period.
This prevents that the Uplink_test never finishes because it destructs the
Uplink connection too often.
* The test finishes not before at least 3 link-down-up steps were executed.
* Replace the Allocator_avl's used for the TX packet allocators of the Nic
and Uplink Connection with the better suited Nic::Packet_allocator.
Ref #4419
The service is merely announced but trying to request a session always causes a
Service_denied exception. This helps in scenarios where the client is
won't open a session anyway but expects the service to be available. This is
considered a temporary solution.
Ref #4419
This patch reverts the vfs-watch-handle creation whenever the subsequent
allocation of the VFS server's 'Watch' object fails. This can happen
when the session RAM or cap quota is depleted.
Fixes#4472
This fixes the following warning when building the binary archive:
Library-description file vfs_capture.mk is missing
Library-description file vfs_tap.mk is missing
'Platform::Device_pd::attach_dma_mem' may lead to insufficient resources
for meta data, which is reflected to the client via 'Out_of_caps' or
'Out_of_ram'. In case the client upgrades its session the quotas need to
be passed to core as done by
'Platform::Device_pd::Expanding_region_map_client::attach'.
issue #4451
Use 'avail_caps' and 'avail_ram' for resource guards because 'used_caps'
and 'used_ram' do not account for resources given to the platform
driver. This lead to incorrect resource accounting by the GPU
multiplexer.
issue #4451
The calculations of packet_size and packet_count in the block_io() did
not consider rounding errors. This resulted in diverging values over
several bisecting operations (/= 2) and wrongly-size packet allocations
as well as memcpy operations.
Related to #2263 (comments about partial block accesses and
_block_io()).
Fixes#4471
The NIC router used to handle each type of packet-stream signal with a distinct
method in the Interface class. However, merging those methods has advantages.
It ensures that sent packets that were already acknowledged by the counter side
are always released before handling received packets. This frees packet stream
memory which facilitates the potential allocation of response packets while
handling received packets. Furthermore, it simplifies the code and reduces the
number of entry points into the router.
This commit also removes the installation of signal handlers at packet streams
for events that are of no interest for the router (TX-ready-to-ack /
RX-ready-to-submit at NIC sessions and RX-ready-to-ack / TX-ready-to-submit at
Uplink sessions).
Fixes#4470
Whenever the nic_router encounters ARP requests on an interface
that does not have a valid IP config it will ignore them. However,
When increasing the verbosity of the component for diagnostic
purposes the resulting 'Bad network protocol' message is misleading.
Issue #4455.
* Test DHCP RENEW by the test client in the unmanaged variant.
* Add event IDs to log output of test client in order to prevent false positive
result in the managed variant.
* Let managed and unmanaged variant have separate string patterns for
'run_genode_until' because they already had different output and it will
differ even more as we don't want to test DHCP RENEW with the managed
variant.
* Delay first test client DHCP in order to fix unexpected sporadic initial IP
config.
* Remove some unnecessary code from the run script
Fixes#4460
The NIC router did update the IP config of a domain on a completed DHCP
REQUEST but not on completed DHCP RENEW or DHCP REBIND. Thus, it didn't adapt
to "real" DHCP servers (not NIC router servers) that got restarted with a
changed configuration by the means of RENEW/REBIND. The commit fixes this.
Note, that testing this is complicated as we don't have the necessary
infrastructure (we cannot simply use the DHCP server of the NIC router as this
would apply a link down/up sequence in order to let the client restart DHCP)
Ref #4460
by using the io_mem RPC of the platform session instead of parsing the
bar resources manually. This commits avoids and breakage on systems where
the Intel graphic cards just uses 64bits with addresses above 4G.
Issue #4450
Our usb_host driver supports UHCI, OHCI, EHCI, and XHCI host
controllers. The USB4 host interface / Thunderbolt is currently not
supported and must therefore not be passed to the USB host driver.
With this fix, the driver no longer aborts on the Tigerlake notebook and
just skips the out-of-region ACPI table. Issue #4452 is not fixed by
this commit, but in this specific case the table is not used anyway.
Check if there are a least 4 caps + 2MB (heap) + possible buffer size
available before any resource allocation. Only account resources that are
actually used.
issue #4451
The former implementation relied on the behaviour of how the old
intel fb driver requested the pci devices. The new lxkit however actually
really want to have all available pci devices.
Issue #4450
If size is zero, the platform goes out of service by:
[init -> platform_drv] Error: Uncaught exception of type 'Genode::Ram_allocator::Denied'
[init -> platform_drv] Warning: abort called - thread: e
Issue #4450
This patch adds the trace-logger utility to the default set of packages
along with an optional launcher. With this change, only two steps are
needed to use Genode's tracing mechanism with Sculpt:
- Add 'trace_logger' to the 'launcher:' list of the .sculpt file
- Either manually select the 'trace_logger' from the '+' menu,
or add the following entry to the deploy configuration:
<start name="trace_logger"/>
By default, the trace logger is configured to trace all threads
executed in the runtime subsystem and to print a report every 10
seconds. This default policy can be refined in the launcher's <config>
node. Note that the trace logger does not respond to configuration
changes during runtime. Changes come into effect not before restarting
the component.
Issue #4448
This patch changes the output format of the trace logger to become
better suitable for human consumption. For example, when instrumenting
the VFS server in Sculpt using the GENODE_TRACE_TSC utility, the
trace logger now generates tabular output as follows.
Report 4
PD "init -> runtime -> arch_vbox6 -> vbox -> " ----------------
Thread "vCPU" at (0,0) total:12909024 recent:989229
Thread "vCPU" at (1,0) total:5643234 recent:786437
PD "init -> runtime -> ahci-0.fs" -----------------------------
Thread "ahci-0.fs" at (0,0) total:910497 recent:6335
Thread "ep" at (0,0) total:0 recent:0
71919692932: TSC process_packets: 8005M (4998 calls, last 4932K)
71921558516: TSC process_packets: 8006M (4999 calls, last 1596K)
71922760220: TSC process_packets: 8007M (5000 calls, last 1006K)
71929853586: TSC process_packets: 8009M (5001 calls, last 1840K)
71931315246: TSC process_packets: 8011M (5002 calls, last 1253K)
72127999920: TSC process_packets: 8016M (5003 calls, last 5606K)
72129568198: TSC process_packets: 8018M (5004 calls, last 1345K)
77161908178: TSC process_packets: 8029M (5005 calls, last 11349K)
77643225736: TSC process_packets: 8029M (5006 calls, last 217K)
89422100594: TSC process_packets: 8035M (5007 calls, last 5656K)
89422123632: TSC process_packets: 8035M (5008 calls, last 1342)
Thread "signal handler" at (0,0) total:36329 recent:3001
Thread "signal_proxy" at (0,0) total:51838 recent:13099
Thread "pdaemon" at (0,0) total:97184 recent:332
Thread "vdrain" at (0,0) total:1266 recent:286
Thread "vrele" at (0,0) total:1904 recent:516
PD "init -> runtime -> nic_drv" -------------------------------
Thread "nic_drv" at (0,0) total:34044 recent:897
Thread "signal handler" at (0,0) total:369 recent:142
...
Subjects that belong to the same PD are grouped together. The formerly
optional affinity and activity options have been removed. Those
information are now unconditionally displayed. The trace entries
belonging to a thread appear as slightly indented.
The patch also updates the coding style, avoiding excessively long
lines.
Issue #4448
This patch reduces repetitive log output by omitting inactive trace
subjects from the log output. The information about all subjects can
still be dumped by setting 'verbose="yes"'.
Issue #4448
This patch splits the creation and updating of monitor objects into two
stages. The creation of a monitor object changes the state of the
associated trace subject. The patch ensures that the new state is
captured by the update of the monitor object.
Issue #4448
This patch makes the trace-subject state as reflected to the trace
monitor more accurate.
Until now, a subject could be in UNTRACED or TRACED state. In reality,
however, there exists an intermediate state after the trace monitor
called 'trace' for the subject but before the subject locally activated
the tracing (done when passing a trace point). This intermediate state
was reflected as UNTRACED. Consequently, threads that never pass a trace
point (e.g., just waiting for I/O) would remain to appear as UNTRACED
even after enabling its tracing by the trace monitor. This is confusing.
This patch replaces the former UNTRACED and TRACED states by three
distinct states:
UNATTACHED prior any call of 'trace'
ATTACHED after a trace monitor called 'trace'
but before the tracing is active
TRACE tracing is active
Fixes#4447
The utilities of the new util/formatted_output.h header complement the
existing base/output.h with the text-formatting support needed to
produce tabular output.
Fixes#4449
This commit adjusts the value such that USB sessions requested by
VirtualBox6 on Sculpt OS can get established on the first try without
invoking the session-retry mechanism. This reduces the number of
diagnostic log messages like:
Error: Insufficient 'ram_quota',got 6296372 need 6297928
The existing assignment of CPU quotas did not anticipate the dynamic
reconfiguration of init. It merely tracked the available CPU quota by
deducing the consumed amount from a global variable but never
replenished the value. This worked for static scenarios but failed in
situations where components are dynamically re-started.
So far this deficiency remained detected because CPU quotas were not
used in highly dynamic systems like Sculpt OS. However, this has
recently changed by commit "sculpt: assign CPU quotas".
The patch improves the accounting by mirroring the existing handling of
RAM and cap quotas. Note that the CPU-quota accounting is still rather
limited. In particular the dynamic rebalancing is not yet supported.
Issue #4445
With the consolidation of the file-system session's signal handlers
implemented by commit "file_system_session: merge ack and submit sigh",
we can now change the VFS server to produce batches of acknowledgements
before explicitly waking up the client. (in contrast to the traditional
'acknowledge_packet', the new 'try_ack_packet' triggers no signal)
Issue #4388
Split the trace buffer into two partitions in order to prevent overwriting
of entries when the consumer is too slow. See file comment in buffer.h.
genodelabs/genode#4434
This commit simplifies the current implementation by overloading the
length field with a padding indicator in addition to the zero-length
head entry. This simplifies the iteration semantics as it eliminates
the need for determining whether a zero-length entries is the actual
head of the buffer or a padding at the buffer end.
genodelabs/genode#4434
* Unifies the declaration of callbacks which manage driver/client
shared dataspaces
* Move the Linux driver-specific callback implementation to the
lx_emul library from the PC's USB host driver
Fixgenodelabs/genode#4439
* The problem occured only on OKL4, seL4, and L4/Fiasco
* The test used to continue submitting packets regardless of how many were in
flight
* This commit limits the in-flight packets at the Uplink/Nic connections to 40
each
Ref #4419
This commit changes the touch-click filter to adhere the following
sequence:
touch (physical)
press (artifically generated)
release (artificially generated)
release_touch (physical)
This order is important because nitpicker's focus handling takes
press/release events into account. If the release-touch event appears
before the release event, nitpicker subsumes the release-touch event
to the sequence that started with the press event, instead of handling
it as a free-standing event.
Issue #4332
When a device got already acquired by a platform session client, do not
return the same capability again, even if the same platform session
client requested it. Therefore, make doubtful behaviour of client components
visible, and do not have to struggle with Platform::Device instances
instantiated multiple times, which care of the lifetime of the device
capability internally.
Fixgenodelabs/genode#4379
* Switch from the legacy usb_host driver to the new PC version
in recipes and automated tests
* Update documentation snippets
* Remove outdated, unused usb_rndis run-script
Fixgenodelabs/genode#4416
Do not only report devices, but the current configuration of the driver too,
as long as the `report` node in the configuration states it.
Ref genodelabs/genode#4416
To stay consistent with the configuration of the legacy usb_host_drv
and other components as well, do not report USB devices by default,
but when the following XML node is set within the component's
configuration:
<report devices="yes"/>
Ref genodelabs/genode#4416
The new usb_host driver for PC by default needs more RAM quota in contrast
to the old one. To minor warnings and repeated attempts to open a USB
session from a client, this commit increases the default RAM quota by one
page.
Ref genodelabs/genode#4416
Adds a function to the USB part of the Genode's C API, to enable
usb_host drivers to acknowledge USB request in client's packet buffer
although they are not assigned to an USB device. The requests are
marked with a "no device" error.
This commit fixes a regression originally solved in genodelabs/genode#4149
Ref genodelabs/genode#4416
XML allows attribute values like <node attr="\"/>. The XML parser
wrongly reflects this case as 'Invalid_syntax'. This behavior stems from
the implicit use of the 'end_of_quote' function, which considers the
sequence of '\"' as a quoted '"' rather than the end of a quoted string.
The patch solves this problem by making the 'end_of_quote' part of
the tokenizer's scanner policy.
The patch removes the 'end_of_quote' function from 'util/string.h'
because it is not universal, and to avoid the ambiguity with
'SCANNER_POLICY::end_of_quote'.
Fixes#4431
The Single_file_system now forwards the
`File_io_service::notify_read_ready` method to the
handle as it already did for most of the other methods.
genodelabs/genode#4394
'generate(Xml_node node)', as used by the Sculpt manager, calls this
function instead of the lambda version. The 'report' function of the
'Genode::Reporter' does not throw an exception in case there is not
enough backing storage for the 'generate' request. Therefore, we have to
check this condition in a loop and call '_increase_report_buffer' in
case size limits are reached.
Patch by Norman Feske.
issue #4369
This reference member is not used anywhere in the code. This prompts
clang to complain about it. Eliminate the member and all the plumbing
associated with it to silence the warning.
Issue #4421
Clang really doesn't like char subscripts. I can't say I blame it. Fix
the warning by an explicit cast to unsigned.
include/nitpicker_gfx/tff_font.h:230:53: error:
array subscript is of type 'char' [-Werror,-Wchar-subscripts]
Tff::Vertical_metrics const m = _vertical_metrics['m'];
^~~~
Issue #4421
Clang likes to complain when lambdas capture parameters without
actually using them. This patch fixes a couple of such problems in VFS
related os module code.
Issue #4421
* Creates sessions to all supported services of the black hole component
* Test-drives the Event and Capture session with dummy input
* Adds the test to the default list of depot_autopilot.run
* Test-driving the Audio_in and Audio_out sessions is still missing and should
be added via a dedicated commit
Ref #4419
To make room for the re-newed usb_host_drv basing on Linux 5.14 and
the re-newed lx_kit/lx_emul we have to move the depot recipe and
consistently name the old drivers with a legacy_ prefix.
Ref genodelabs/genode#4416
This patch makes nitpicker's "clicked" report useful for the detection
of clicks outside of any client. This is needed in situations where the
dialog should close when clicking outside its screen area. In the new
version, a click outside any client results in a report without a
'label' attribute. Furthermore, the report is augmented by the sequence
number of the click, which allows for freshness checks by the consumer of
the report (i.e., sculpt_manager).
Issue #4398
If the buffer contains padding at the end, the iteration must continue
in order to restart iteration from the start of the buffer.
genodelabs/genode#4244
The functionality of the test-block-client, test-block-server, and
test-block-bench components is now covered by the block_tester
application and the vfs_block server.
Issue #4405
This patch eliminates warnings that occurred as side effect of using the
'Session_policy' utility ("Warning: no policy defined for label...").
The new version uses the 'with_matching_policy' function instead, which
has the nice side effect of simplifying the error handling.
This patch makes the server-side policy-matching logic available outside
the 'Session_policy' class. Given that the new 'with_matching_policy'
function does not throw any exception, it gives server implementations
the freedom to avoid the C++ exception mechanism for the policy handling.
If the platform driver lacks the 'managing_system="yes"' attribute,
requests for DMA addresses return 0. This patch is meant to help
diagnosing such configuration issues.
Issue #2243
This patch enhances the PD-session interface with the support needed for
user-level device drivers performing DMA. Both RPC functions are
intended for the direct use by the platform driver only. If invoked for
PDs that lack the managing-system role, the operations have no effect.
The 'dma_addr()' RPC function allows the platform driver to request the
DMA address of a given RAM dataspace. It is meant to replace the
'Dataspace::phys_addr' RPC function.
The 'attach_dma' RPC function adds the given dataspace to the device
PD's I/O page table. It replaces the former heuristics of marking DMA
buffers as uncached RAM on x86.
With this patch, the UNCACHED attribute of RAM dataspaces is no longer
used to distinguish DMA buffers from regular RAM dataspaces.
Issue #2243
The new event type allows for the propagation of sequence numbers as a means to
validate the freshness of input handling. E.g., an menu-view-based application
can augment artificial sequence numbers to the stream of motion events supplied
to 'menu_view'. Menu view, in turn, can now report the latest received sequence
number in its hover reports, thereby enabling the application to robustly
correlate hover results with click positions.
Issue #4398
This patch replaces formerly blocking packet-stream operations by
the explicit use of 'wait_and_dispatch_io_signal' for blocking.
It also removes a misleading comment that promised a fire-and-forget
behavior whereas the implementation relied on blocking I/O anyway.
Issue #4390
The VFS block plugin used to depend on the blocking semantics of the
packet stream's 'get_acked_packet'. This patch replaces this dependency
by the use of 'wait_and_dispatch_one_io_signal'. However, in order to
implement this change, the custom instance of a 'Signal_receiver' had to
be removed as well.
To keep this patch as little invasive as possible, it does not touch the
direct use of the block session's packet stream, which should better be
replaced by the 'Block::Connection::Job' API.
Issue #4390
The zynq_nic_drv follows a zero-copy approach and thus uses the packet
buffers as DMA memory. In order to know when the RX DMA memory can be used
for another packet, a custom ack_avail_handler is needed.
Similarly, packets received from the Uplink session are not copied to a
DMA buffer but to directly passed on as DMA memory. For this purpose,
a a custom packet_avail handler is needed.
genodelabs/genode#4384
The 'read' and 'write' utilities are from a time before the VFS API
as os/vfs.h was available. They rely on the (now removed) blocking
semantics of the packet-stream interface.
The only remaining legitimate use case of the direct interaction with
the file-system session without VFS is the back end of gcov, which needs
a way to exfiltrate the statistical data using a channel that is
independent from the libc or the VFS.
Issue #4390
This patch replaces the direct use of a file-system session via the
'file_system/util.h' helpers by the VFS using the os/vfs.h API. This
makes the component more flexible while removing the dependence from
read and write utilities of file_system/util.h, which happen to rely on
the (now removed) blocking packet-stream semantics.
Issue #4390
Since the change "block_tester: limit batching in sequential test", the
sequence test blocks infinitely when encountering a length value smaller
than the block size.
This patch takes precautions against the use of blocking packet-stream
operations like 'submit_packet'.
With the change of issue #4388, the ready-to-submit signals are no
longer implicitly handled. Hence, a call of submit_packet to a
saturated submit queue blocks infinitely.
Issue #4390
* use 'Id_space::apply_any' instead of 'for_each' to destroy session local
buffer objects
* save session capability in session because 'cap()' is not valid in
'Session_component' destructor because it was dissolved before calling
'Root::_destruct_session', the cap is necessary to remove owned
buffers from the EP
issue #4380
Add 'export_buffer'/'import_buffer' calls in order to support buffer
sharing between GPU sessions.
Reduce CAP costs for Gpu::Connection from 256 to 32.
issue #4380
Account RAM and CAP resources for GPU sessions and trigger client
upgrades before allocating resources at the multiplexer. This prevents
the multiplexer from running out of resources.
issue #4380
Imagine receiving the signal for an available TX ack or an available RX packet
at the Uplink connection but a later received signal for a link-state change
(to link state "down") at the same connection is handled first and destructs
the Uplink connection before the handling of the former signals. In this case,
the methods 'Uplink_client_base::_conn_tx_handle_ack_avail' and
'Uplink_client_base::_conn_rx_handle_packet_avail' must be guarded against an
unconstructed '_conn' member, but they weren't so far.
Fixes#4384
So far, the generic Uplink connection code considered NIC drivers to transmit
connection RX packets in three different manners. Most of the drivers follow
the "normal" way of transmission with only one driver callback from generic
code. The monolithic USB NIC-driver, however, used to send in a "burst" mode
that required a dedicated path with multiple driver callbacks in the generic
code. And then there were drivers that had a fully custom function for doing
transmissions.
Also for handling connection TX acks, there was a "normal" and a
"custom handler" way.
Today, all NIC drivers in the Genode repos and the Genode-World repo follow the
"normal" way. Therefor, the unused code can be removed.
Ref #4384
This patch equips Sculpt with the ability to customize the system image
in very flexible ways.
All customizable aspects of the image have been relocated from the
former sculpt.run script and the accompanied gems/run/sculpt/ directory
to a new location - the sculpt/ directory - which can exist in any
repository. The directory at repos/gems/sculpt/ serves as reference.
The sculpt directory can host any number of <name>-<board>.sculpt files,
each containing a list of ingredients to be incorporated into the
Sculpt system image. The <name> can be specified to the sculpt.run
script. E.g., the following command refers to the 'default-pc.sculpt'
file:
make run/sculpt KERNEL=nova BOARD=pc SCULPT=default
If no 'SCULPT' argument is supplied, the value 'default' is used.
A .sculpt file refers to a selection of files found at various
subdirectries named after their respective purpose. In particular, There
exists a subdirectory for each file in Sculpt's config fs, like
nitpicker, drivers... The .sculpt file selects the alternative to use
by a simple tag-value notation.
drivers: pc
The supported tags are as follows.
*Optional* selection of /config files. If not specified, those files are
omitted, which prompts Sculpt to manage those configurations
automatically or via the Leitzentrale GUI:
fonts
nic_router
event_filter
wifi
runtime
gpu_drv
Selection of mandatory /config files. If not specified, the respective
'default' alternative will be used.
nitpicker
deploy
fb_drv
clipboard
drivers
numlock_remap
leitzentrale
usb
system
ram_fs
Furthermore, the .sculpt file supports the optional selection of
supplemental content such as a set of launchers.
launches: nano3d system_shell
Another type of content are the set of blessed pubkey/download files
used for installing and verifying software on target.
With the new version, it has become possible to supply a depot with the
the system image. The depot content is assembled according to the 'pkg'
attributes found in launcher files and the selected deploy config.
The resulting depot is incorporated into the system image as 'depot.tar'
archive. It can be supplied to the Sculpt system by mounting it into the
ram fs as done by the 'ram_fs/depot' configuration for the ram fs.
It is possible to add additional boot modules to the system image. There
are two options.
build: <list of targets>
This tag prompts the sculpt.run script to build the specified targets
directly using the Genode build system and add the created artifacts
into the system image as boot modules.
import: <list of depot src or pkg archives>
This tag instructs Sculpt to supply the specifid depot-archive content
as boot modules to the system image. This change eliminates the need for
board-specific pkg/sculpt-<board> archives. The board-specific
specializations can now be placed directly into the respective .sculpt
files by using 'import:'.
To make the use of Sculpt as testbed during development more convenient,
the log output of the drivers, leitzentrale, and runtime subsystems
can be redirected to core using the optional 'LOG=core' argument, e.g.,
make run/sculpt KERNEL=linux BOARD=linux LOG=core
The former pkg/sculpt-installation and pkg/sculpt-installation-pc
archives have been replaced by pkg/sculpt_distribution-pc, which
references the generic pkg/sculpt_distribution archive. Those pkgs are
solely used for publishing / distribution purposes.
Fixes#4369
Fix some trivial cases where the signedness of the constant value does
not match the signedness of type the code expects to see. GCC can be
asked to warn about those by passing Wsign-covnersion flag.
Issue #4354
This comes up when building the code with clang 13. It happens due to
recently enabled Wconversion warning, which in case of clang also
enables implicit-int-conversion warning. The warning reads:
fs_file_system.h:937:44: error: higher order bits are zeroes after
implicit conversion [-Werror,-Wimplicit-int-conversion]
::File_system::Watch_handle fs_handle { -1U };
~~~~~~~~~ ^~~
This can be fixed by properly specifying fs_handle value to be of
unsigned long type.
Issue #4354
Remove '_expected_offset' check on round trip test from RX packet,
because allocators between RX/TX can have different allocation
strategies. Rely on 'pattern' check for RX packets only.
In loopback server alloc size must match actual packet size.
issue #4312
Override 'try_alloc/free' because ethernet frame headers are 14 bytes
(src/dst mac (12) + ethertype (2)) causing the IP header to be 2 byte
aligned, leading to problems on platforms that require load/store
operations to be naturally aligned when reading, for example, 4 byte IP
addresses. Therefore, we align the allocation to 2 bytes, so the IP
header is aligned to 4.
issue #4312
This patch improves the robustness of the CPU-affinity handling.
- The types in base/affinity.h received the accessors
'Location::within(space)' and 'Affinity::valid', which alleviates
the fiddling with coordinates when sanity checking the values,
in init or core.
- The 'Affinity::Location::valid' method got removed because its
meaning was too vague. For sanity checks of affinity configurations,
the new 'within' method is approriate. In cases where only the x,y
values are used for selecting a physical CPU (during thread creation),
the validity check (width*height > 0) was not meaningful anyway.
- The 'Affinity::Location::from_xml' requires a 'Affinity::Space'
as argument because a location always relates to the bounds of
a specific space. This function now implements the selection of
whole rows or columns, which has previously a feature of the
sandbox library only.
- Whenever the sandbox library (init) encounters an invalid affinity
configuration, it prints a warning message as a diagnostic aid.
- A new 'Affinity::unrestricted' function constructs an affinity that
covers the whole affinity space. The named functions clarifies
the meaning over the previous use of the default constructor.
- Core's CPU service denies session requests with an invalid
affinity parameter. Previously, it would fall back to an
unrestricted affinity.
Issue #4300
After VirtIO::Queue refactoring buffers no longer share the same
dataspace as VirtIO rings. This makes optimal buffer calculations a lot
easier. In this case 64 buffers 2kB each will need precisely 128kB of
RAM. Previous value of 2016 will just waste 768b.
Fixed#4347
The key changes in this patch are:
* Buffer allocation is moved into a separate Buffer_pool helper. The
implementation of the buffer allocation strategy does not change.
The helper allocates a single RAM dataspace and splits it in multiple,
equally sized chunks.
* Management of main descriptor ring is enacapsulated in Descriptor_ring
helper class.
* Use separate RAM dataspaces for descriptor rings and buffers.
Previously both of them were packed into a single dataspace. This
might have been more RAM efficient, but IMO it made the code uglier and
harder to understand.
* All of the VirtIO::Queue members are now initialized on the class member
initializer list. This is possible due to previously listed changes.
* Since all VirtIO::Queue members are initalized on member initalizer
list, some additional ones can be marked as const, ex _avail, _used ring
pointers.
* Move descriptor writing code into a common method used by both
write_data and write_data_read_reply members. This avoids some code
duplication between those methods.
* Get rid of request_irq argument that most public VirtIO::Queue methods
accept. None of the existing drivers use it and I doubt this will
change any time soon.
* Use Genode namespace by default in Virtio.
This patch also fixes at least one bug that I discovered while working
on VirtIO block device driver. Namely, when chaining descriptors only the
first descriptor in the chain should be exposed in the available ring.
Issue #4347
The const-variant of the data() method contained an erroneous
calculation of the tail size. This led to the size guard throwing
exceptions when trying to parse TCP packets that only contained the
TCP header.
Fixesgenodelabs/genode#4340
Thanks to Piotr Tworek for the fix and his explanation as follows:
The basic idea is to try to fit payload data into the descriptor used to
send the header. If there is no payload, or the payload fits exactly
into the remaining space in the header decriptor, len should be 0 and
only one descriptor should be used. In such case the "next" and "flags"
members of the descriptor structure should be set to 0.
In case there is some extra payload data to send, but its size is
bigger than the remaining free space in the descriptor used to send the
header, len should contain the remaining size of the payload that
can't be sent via the header descriptor. The code will then chain
additional descriptors to handle this remainder.
With the len variable shadowing, the code will never queue the remaining
data.
Issue #4327
Share datastructures for clock, power and reset related configurations
per device. In the generic platform driver component these structures
are kept empty. Driver derivates can fill the clocks settings, power and
reset switches with life. The former Driver::Env gets removed.
Fix#4338
This change of the inner working of the platform driver for ARM allows
clients to have permanent open sessions, as long as a policy node matches
the client. If devices disappear from the policy resp. from the set of
available devices (hotplug), the devices ROM of the session gets updated,
and a corresponding device session gets closed. If the device remains
untouched in the configuration but other devices appeared/disappeared, the
device session is not affected.
Ref #4330
* Only give managing_system permission when all parent nodes of the
corresponding component agree in doing so.
* Move the physical memory constrains heuristic from sandbox library to core
Fix#4335
* Track all caps and ram quotas of the sub-sessions properly
* Release DMA buffers, it is not done implicitely when destroying
the Constrained_ram_allocator
* Do not replenish quota before really releasing memory from
the allocator
Issue #4330
The Session_component must be destroyed before updating the device
model because the Session_component must also release all previously
acquired devices. If the device model is updated before, the devices
might have been removed.
Issue #4330
Pre-allocate all possible type of policy objects as part of the thread meta
state to avoid increased memory consumption due to different policy object
sizes. The cpu_balancer accounts the memory per client and can't forward
potentially occurring out-of-ram exceptions during config-ROM update phases.
Fixes#4333
The commits avoids reading in and allocating memory for all potentially
threads, which are potentially currently not existent (but configured in the
policy beforehand). Instead the policy is read in and evaluated when a thread
is created and policy changes are solely applied to existing/running threads.
By this the commit avoids the increase of memory consumption during the
evaluation of policies during config ROM updates.
Issue #4333
This implements the necessary bits to provide 2D framebuffer support on
top of VirtIO GPU device as implemented in Qemu. I don't know if any
other implementation of this specific device exists.
Compared to the ramfb driver which already exists in Genode Virtio FB driver
has one major benefit. It allows Qemu window to be dynamically resized at
runtime. The driver will treat this as resolution change and act accordingly.
Ramfb driver can currently only use the hardcoded 1024x768 screen size. Changing
screen resolution might not sound like a big deal, but it is rather useful to
run Genode on Qemu in full screen mode.
Some more advanced devices like VirtIO GPU do expect they can receive
responses to VirtIO commands they issue via VirtIO queue. Such responses
are not sent via a separate device writeable queue. Instead the driver
is expected to queue some additional descriptors and buffers which the
device can then use to provide the reply.
This patch adds support for such write-data-read-response opeartion to
Genode VirtIO::Queue implementation. The implementation is pretty simple
and does not support any fancy features like receiving the response
asynchronously. Instead the operation will use caller provided callback
to wait for the device to process the command. Once this callback
returns the write-data-read-response VirtIO::Queue function will invoke
another callback passing received response as argument.
Mesa queries information about the underlying device and this header
denotes the layout of the information. It is also used by the driver
itself to populate the 'info_dataspace'.
Issue #4329.
This filter bridges the gap between a touchscreen driver, which
generates raw touch events and traditional GUI applications that expect
a pointer (absolute motion, press/release of the left mouse button).
Fixes#4332
This patch changes the 'Allocator' interface to the use of 'Attempt'
return values instead of using exceptions for propagating errors.
To largely uphold compatibility with components using the original
exception-based interface - in particluar use cases where an 'Allocator'
is passed to the 'new' operator - the traditional 'alloc' is still
supported. But it existes merely as a wrapper around the new
'try_alloc'.
Issue #4324
Since the top-level node of the output ROM is always generated by the
rom_filter, there is no way to pass-through the content of an input ROM
without wrapping in an addition XML node.
genodelabs/genode#4326
This patch makes the test less dependent on the rate of state updates by
calculating the upgraded quota from the values found in the state report
instead of simply increasing the '_ram_quota' for each incoming report.
This patch replaces the 'Ram_allocator::alloc' RPC function by a
'try_alloc' function, which reflects errors as 'Attempt' return value
instead of an exception.
Issue #4322
Issue #3612
The new interfaces are meant to gradually replace the existing
Gpio_session interface.
- Each session refers to a single pin.
- The session types distiguish the direction of the signal as input or
output.
- Pin coordinates can be selected via session labels.
- GPIO interrupts are covered by the regular IRQ session interface.
The interfaces are accompanied by framework utilities and interfaces:
- os/pin_driver.h
- pin_control_session/component.h
- pin_state_session/component.h
These headers relieve GPIO drivers from implementing boilerplate code by
providing device-agnostic portions. The A64 pio driver serves as
reference for using those utilities.
https://github.com/nfeske/genode-allwinner/tree/master/src/drivers/pin/a64Fixes#4315
Accidentally, the size of IOMEM dataspace got accounted within the
implementation of the platform driver for ARM. Instead we should
only account a bit for the metadata and paging of the I/O memory.
Fix#4307
The custom ack avail handler is required for zero-copy nic drivers (e.g.
the zynq nic driver), which must release the corresponding DMA buffers.
Fixesgenodelabs/genode#4277
This component can service Qemu VirtIO mouse, keyboard and tablet
devices. The implementation is based on VirtIO 1.1 device spec. Its
described in section 5.8 "Input Device".
Issue #4282
- CPU-architecture annotations
- Change order of top-level menu, moving Mesa driver to the end
- Add black_hole, recall_fs, file_fault
- Add usb_webcam, test-capture
- Add audio driver and mixer
- Add vbox6, keeping vbox5-nova-sculpt as fallback
- Remove recall_fs launcher, which is obsolete with the recall_fs pkg
- Replace system_clock by system_clock-pc pkg
Issue #4281
This patch extends the notion of having only one uniquely hovered client
in the presence of held keys.
If motion occurs once a key is pressed (e.g., while dragging), the
receiver of the key sequence observes the motion events. In this case,
we have to submit an artificial leave event to the originally hovered
client so that no more than one client observes itself as being hovered
at the same time. Once the key sequence is finished, the hovering is
updated again, eventually presenting a motion event to the originally
hovered client and a leave event to the receiver of the key sequence.
Issue #4176
The new 'Env::try_session' method mirrors the existing 'Env::session'
without implicitly handling exceptions of the types 'Out_of_ram',
'Out_of_caps', 'Insufficient_ram_quota', and 'Insufficient_cap_quota'.
It enables runtime environments like init to reflect those exceptions to
their children instead of paying the costs of implicit session-quota
upgrades out of the own pocket.
By changing the 'Parent_service' to use 'try_session', this patch fixes
a resource-exhaustion problem of init in Sculpt OS that occurred when
the GPU multiplexer created a large batch of IO_MEM sessions, with each
session requiring a second attempt with the session quota upgraded by
4 KiB.
Issue #3767
'Out_of_ram' was so far the only exception a client had to deal with
during buffer managment. Allocating memory, however, does not only
consume RAM quota but CAP quota as well.
This commit tries to mitigate that shortcoming by reflecting the
'Out_of_caps' state back to the client. Furthermore it allows for
resource accounting on certain client allocations, e.g. buffers.
Fixes#4284.
Allocating and mapping buffers not only consumes RAM quota, it consumes
CAP quota as well. Extended the Gpu session to allow for dealing with
that on the client side.
On a side note, the amount of initial CAP quota needed to establish
a connection is increased to cover the current costs of the Intel
GPU multiplexer.
Issue #4284.
The platform driver uses a 'Constrained_ram_allocator' to allocate
meta-data on behave of a client. It uses the PD session as
'Ram_allocator' back end that in return is implemented via the
'Expanding_pd_session_client'.
Whenever the PD client itselft comes into resource shortage it will
ask its parent unconditionally. However, depending on the integration,
such a request may be left unanswered.
This commit introduces a check to prevent that situation from
occurring. In case the platform driver notices the resource shortage
it will reflect that back to the client.
Issue #4284.
ROM clients have to request an initial update of dynamic ROMs explicitly
and should not depend on artificial signals from the ROM session on
signal-handler registration.
Issue #4274
The sequence app should immediately stop the child when it called
parent().exit(). Otherwise, the child will continue execution which
causes a race condition: The child's ld.lib.so will eventually destruct
an Attached_rom_dataspace for the config rom. If sequence destructed the
corresponding service first, we will get an Ipc_error.
genodelabs/genode#4267
This patch introduces a C API to be used by input drivers to generate
Genode events. The initial version is limited to multitouch events only.
Fixes#4273
The former implementation did not internally track ROM changes notified
vs. delivered to the client. We adapt the versioning implementation
implemented in dynamic_rom_session.h and enable explicit notification of
the current version.
The feature is used by the clipboard to notify permitted readers of the
clipboard ROM service on focus change via the newly created private
Rom::Module::_notify_permitted_readers() function.
Fixes#4274
The various mapping methods are modelled after the requirements of
the Intel GPUs or rather the Mesa driver back end.
With upcoming support for other driver back ends, we need to
sequeeze their requirements in as well. For now hijack 'map_buffer'
to provide for specifying the kind of attributes the client needs.
For now all buffers mapped in the GGTT for Intel GPUs are treated
as RW.
Issue #4265.
This call allows for checking if the given execution buffer has been
completed and complements the completion signal. Initially the GPU
multiplexer always sent such a signal when the currently scheduled
execution buffer has been completed. During enablement of the 'iris'
driver it became necessary to properly check of sequence number.
In case of the Intel GPU multiplexer the sequence numbers are
continous, which prompted the greater-than-or-equal check in the
DRM back end. By hidding this implementation detail behind the
interface, GPU drivers are free to deal with sequence numbers any
way they like and allows for polling in the client, where the
completion signal is now more of a progress signal.
Issue #4265.
The current info implementation (as RPC) is limited in a few ways:
* The amount of data that may be transferred is constrained by the
underlying base platform
* Most information never changes during run time but is copied
nonetheless
* The information differs depending on the used GPU device and
in its current implementation only contains Intel GPU specific
details
With this commit the 'info' RPC call is replaced with the
'info_dataspace' call that transfers the capability for the dataspace
containing the information only. This is complemented by a client
local 'attached_info' call that allows for getting typed access to
the information. The layout of the information is moved to its own
and GPU-specific header file, e.g., 'gpu/info_intel.h'
Issue #4265.
Rather than using the dataspace capability directly, let the client
choose its own local identifier that is linked to the underlying
capability.
Fixes#4265.
Right now the warning about failure to forward packet from driver to
uplink RX connection reads:
"exception while trying to forward packet from driverto Uplink
connection TX"
Add missing space between "driver" and "to".
Issue #4264
32KB is a rather small value. The driver can cope with it now, but
it does not perform as well as it should. This visible especially
in scenarions like nic_router_flood where we still often hit
synchronous wait path. Bump the size to 256kB.
Issue #4264
The problem can be seen when running nic_router_flood scenarion on arm
qemu_virt boards. With the amount of data this scenario tries to send
the driver quickly complains it has failed to push data into TX VirtIO
queue. After this warning message is printed nothing really happens and
after a while the test scenario fails.
The fact that we can't write all available data to the device is not
unexpected. VirtIO queue size is slected at initialization time and we
don't change it during driver lifetime. It can be tweaked via driver
config, but this does not change the fact that we'll always be able to
produce more data packets than we have free space in the VirtIO queue.
IMO the expected behavior of the driver in such case should be to:
1. Notify the device there is data to process.
2. Wait for the device to process at least part of it.
3. Retry sending queued packets.
One could expect returning Transmit_result::RETRY from _drv_transmit_pkt
would produce such result. Unfortunately it seems that Uplink_client_base
treats RETRY return value as indication of link being down. It'll retry
sending the packet only after the device notifies it the link is once
again up. This is the reason why nothing happens when running
nic_router_flood on top of virtio_nic driver. The link never goes down
in this case so once we fill the TX VirtIO queue and tell the base class
to retry the send, we'll be stuck waiting for link up change event
which will never arrive.
To fix this problem, when sending a packet to the device fails, do a
synchrnonus TX VirtIO queue flush (tell device there is data to process
and wait until its done with it).
With this fix in place nic_router_flood test scenario passes on both arm
qemu_virt boards.
Issue #4264
The contents of those descriptor rings can be modified by the device.
Mark them as volatile so the compiler does not make any assumptions
about them.
Issue #4264
This commit contains features and buf fixes:
* Catch errors during resource allocation
* Because Mesa tries to allocate fence (hardware) registers for each
batch buffer execution, do not allocate new fences for buffer objects
that are already fenced
* Add support for global hardware status page. Each context additionally
has a per-process hardware status page, which we used to set the
global hardware status page during Vgpu switch. This was obviously
wrong. There is only one global hardware status page (set once during
initialization) and a distinct per-process page for contexts.
* Write the sequence number of the currently executing batch buffer to
dword 52 of the per-process hardware status page. We use the pipe line
command with QW_WRITE (quad word write), GLOBAL_GTT_IVB disabled
(address space is per-process address space), and STORE_DATA_INDEX
enabled (write goes to offset of hardware status page). This command
used to write to the scratch page. But Linux now uses the first
reserved word of the per-process hardware status page.
* Add Gen9+ WaEnableGapsTsvCreditFix workaround. This sets the "GAPS TSV
Credit fix Enable" bit of the Arbiter control register (GARBCNTLREG)
as described by the documentation this bit should be set by the BIOS
but is not on most Gen9/9.5 platforms. Not setting this bit leads to
random GPU hangs.
* Increase the context size from 20 to 22 pages for Gen9. On Gen8 the
hardware context is 20 pages (1 hardware status page + 19 ring context
register pages). On Gen9 the size of the ring context registers has
increased by two pages to 21 pages or 81.3125 KBytes as the IGD
documentation states.
* The logical ring size in the ring buffer control of the execlist
context has to be programmed with number of pages - 1. So 0 is 1 page.
We programmed the actual number of pages before, leading to ring
buffer execution of NOOPs if page behind our ring buffer was empty or
GPU hangs if there was data on the page.
issue #4260
Increased number of trace subjects since the test sporadically fails on
some platforms.
Also added a sanity check to print an error message in case we run into
the same issue again.
Fixesgenodelabs/genode#4261
The NIC router parses, stores and forwards DNS domain names from DHCP replies.
Yet the routers DHCP client used to not request DNS domain-name information on
DHCP requests. This caused DHCP servers to skip this information on their
replies although it was available. This commit fixes the issue by adding the
DNS domain name code to the request parameter list of requests from the routers
DHCP client.
The 'black_hole' component provides dummy implementations of common
session interfaces.
At this time, only the 'Audio_out' session is provided if enabled
in the configuration of the component:
<config>
<audio_out/>
</config>
Issue #3653
According to spec the tail pointer points to the next qword instructions
which will be used by the software.
p 1354, Doc Ref # IHD-OS-BDW-Vol 2c-11.15
issue #4254
Superpages (2M, 1G) are not supported by now, but partially copied over code
from base-hw was around. Remove unused register definitions and remove
non-working super page code do avoid confusion.
issue #4254
Size argument of ggtt free range check is ignored, which leads to
overlapping allocations inside, which leads to unavailable IO-MEM exceptions
thrown by core.
issue #4254
Both, trace_logger and vfs_trace had their own trace_buffer.h. This
commit consolidates the existing implementations and provides the
resulting trace_buffer.h at 'include/trace/'. It thereby becomes part of
the trace api archive.
genodelabs/genode#4244
If the trace subjects are not properly destructed when the TRACE client
disappears, enabled sources will be owned by a non-existing client.
In other words, when a TRACE client disappears all sources owned by the
client must be disabled.
genodelabs/genode#4247
test-trace always passed, although tracing was never enabled because the
trace subject was not within the first 32 subjects.
* increase number of queried subjects
* output error if trace subject was not found
genodelabs/genode#4247
With this commit, the NIC router DHCP client reads out the first DNS domain
name (DHCP option 15) if any from a DHCP reply that generates an IPv4 config
for a domain and stores the name together with the IPv4 config for that domain.
DNS domain names are reported via the new report tag '<dns-domain>' if the
'config' attribute in the config tag '<report>' is set.
Furthermore, the NIC router DHCP server becomes able to obtain a DNS domain
name from another domain that has a DHCP client dynamically (given the config
attribute 'dns_config_from' is set and no static DNS config is given) or
statically from its configuration (new config tag '<dns-domain>') and propagate
this name with DHCP replies (DHCP option 15).
The 'nic_router_dhcp_*' tests are adapted to test the new feautures.
The commit also gets rid of some mirrored files in
'test/nic_router_dhcp/manager'.
Fixes#4246
WARNING: BREAKS CONFIG COMPATIBILITY!
This commit changes the configuration interface of the NIC router in a way that
may break systems that use the component without proper adjustment!
How to adjust:
At each occurrence of the 'dns_server_from' attribute in a NIC router
configuration replace the attribute name with 'dns_config_from'. The attribute
value remains unaltered.
DETAILED DESCRIPTION
The new attribute name 'dns_config_from' reflects that also other aspects of
the DNS configuration of the denominated domain are used by the DHCP server
that holds the attribute. This commit is a preparation for forwarding also the
domain name (DHCP option 15) with the mechanism behind the attribute.
Ref #4246
The fact that the IPv4 config was a struct with all data members public was a
mere leftover of an early state of the NIC router. Today, the router
implementation style is to avoid structs and public data members wherever
possible.
This commit slightly changes the behavior of the router regarding log output.
The router used to print malformed IPv4 configurations to the log only if
the 'verbose' config flag was set using this style:
! [my_domain] malformed dynamic IP config: interface 10.0.2.1/24 ...
Now, malformed IPv4 configurations are only printed if the
'verbose_domain_state' config flag is set (like with any IP4v configuration
states) using this style:
! [my_domain] dynamic IP config: malformed (interface 10.0.2.1/24 ...)
Fixes#4242
The NIC router DHCP server used to add an extra option 6 field to DHCP replies
for each DNS server address. This conflicts with RFC #2132 section 3.8 which
states that the addresses should be listed within one option 6 field without
delimiter. The discrepancy is fixed by this commit.
Ref #4242
Via a new configuration attribute, the user can decide whether the router
should answer dropped fragmented IPv4 with an ICMP "destination unreachable"
packet and, if so, which value the ICMP code field of this packet should have.
The default is that the router doesn't send such responses (silently dropping
fragmented IPv4). The behavior is tested by the 'nic_router_ipv4_fragm' test.
Fixes#4236
If the new attribute 'dropped_fragm_ipv4' of the <report> tag in the NIC router
config is set "yes", the router will report the number of packets that were
dropped per interface respectively domain because fragmented IPv4 is not
supported. The default is not to report the counter. The behavior is tested by
the 'nic_router_ipv4_fragm' test.
Ref #4236
The NIC router used to ignore the IPv4 header fields "More fragments" and
"Fragment offset" completely. Therefore higher-level protocols of fragmented
IPv4 were interpreted wrong because each fragment was considered a self-
standing packet, expecting, for instance UDP/TCP headers somewhere inside of
the UDP/TCP data field. Normally, such packets were dropped as soon as the
UDP/TCP checksum check failed because of the misinterpretation. However,
it was also possible for fragmented IPv4 to pass the router although normally
only partially.
IPv4 fragmentation support in the router would introduce some potential
security risks and is presumably not an easy endeavor. So, for now, we settled
on not supporting IPv4 fragmentation. With this commit, the router simply drops
all fragmented IPv4. This is reflected to the log for each fragment as "drop
packet (fragmented IPv4 not supported)" when 'verbose_packet_drop="yes"' is
configured.
The new test 'run/nic_router_ipv4_fragm' is an automated test for this
behavior. The test is added to the autopilot list.
Ref #4236
* the GPU multiplexer now offers the platform service to the Intel
framebuffer driver (driver_manager)
* ajdusted drivers_managed-pc to hand out resources to the GPU driver
* adjust quotas
issue #4233
The platform services is intented to be used by dde_linux's intel_fb_drv
in order to initlialize displays.
* implement and announce platform session
* limit accessible GTT and aperture of client to 64 MB
* forward display engine IRQs to platform client
* move all PCI resources to 'Igd::Resources' class in order to make them
accessible by the platform service and the GPU driver
* fix fence register allocation for id zero (return true)
issue #4233
For mesa-21 the client takes care and manages
the virtual address space of the vGPU by itself and the intel/gpu driver
can't add silently a guard page anymore. Move the patch to the drm/ioctl
of the former mesa version.
Issue #4148#4233
_unmap_dataspace_ggtt requires the cap of Ggtt::Mapping (ring_map, ctx_map)
in order to find the right metadata and to free up the ggtt entries. Also the
pte range is removed already if the metadata was found.
Issue #4148#4233
BREAKS CONFIG COMPATIBILITY:
This commit changes the configuration interface of the NIC router in a way that
may break systems that use the component without proper adjustment!
HOW TO ADJUST:
At each occurrence of the '<uplink ...>' tag in a NIC router configuration
replace the tag name 'uplink' with 'nic-client'. The rest of the tag stays the
same.
The term "uplink" for network interfaces in the router that have a NIC session
client as back end was introduced in a time when Uplink sessions didn't yet
exist. Now, they do and, although both an uplink and an Uplink session
normally describe a network session between router and network device driver,
they are based on two different service types (NIC and Uplink). This can easily
cause confusion when integrating the router (the <uplink> is not related to
Uplink sessions) or trying to understand its functioning (an 'Uplink' object
has nothing to do with the Uplink service).
Therefore, this commit introduces the more specific term "NIC client" for an
interface that is based on a NIC session requested by the router. This doesn't
imply any semantic changes at the NIC router. However, the commit also brings a
broader update of the router's README and removes the term "downlink" that was
used only in documentation to refer to interfaces backed by a NIC session
provided by the router. The term was only associated with this meaning because
it is the natural counterpart to an uplink. This isn't appropriate anymore as
the terms for interface types have moved to a more technical level.
The commit adjusts all scenarios in the basic Genode repositories properly.
Fixes#4238
An interface that received a signal for a link-state change accessed its
domain reference without assuming that it could not be attached to a domain
at that moment. This caused the NIC router to crash with an uncaught exception
of type 'Net::Pointer<Net::Domain>::Invalid'. The commit adds a catch
directive for this exception resulting in the handler doing nothing if not
attached to any domain.
Fixes#4222
The test script failed during preparation of the on-target execution for
USB Armory with the following error:
! can't read "tz_vmm_block_irq": no such variable
Presumably, the script wasn't run anymore since the introduction of the
'tz_vmm_block_irq' variable for i.MX53 QSB. As we do not have infrastructure
for automated testing of the USB Armory and there seems to be not much
interest in using Genode on this platform, this commit simply removes the
support from the script.
Filtering boards in a run script by specs isn't the right way anymore (the
specs do not exist anymore). Nowadays, we have to use [have_board] instead.
Ref #4229
For unknown reasons, the former 'wget genode.org' call, that was meant to test
network in the Trustzone guest on imx53_qsb_tz, didn't succeed anymore although
the same call succeeded on my Sculpt VM Linux. However, 'ping 1.1.1.1' still
works, so, the script now uses this as test for networking instead.
Fixes#4229
So far, in order to create an ARP reply, the NIC router merely created a copy
of the corresponding ARP request and modified only those values that differ.
This approach has the disadvantage of re-using bad parameters from a broken
request. The specific use-case that made this visible was an early version of
the Pine board network driver that used to forward ARP requests with a greater
size than required. The ARP replies of the router re-used this size and
confused other network nodes with that. In general, the NIC router should
rely on the data of incoming packets the least possible. Therefore, with this
commit, the router creates a new ARP reply from scratch and uses only those
values required from the corresponding ARP request.
Fixes#4235
The former declaration of the IPv4 packet did not only use the questionable
tool of implementation-defined C++ bitsets but also lacked access to flags
"don't fragment" (DF) and "more fragments" (MF). This commit replaces the
C++ bitsets by using the register framework and introduces accessors for the
missing flags.
Ref #4236
This commit introduces a C-API to the Uplink session, as well as to
serve as a Block service. It can be used by drivers ported from
C-only projects, like the Linux kernel, or BSD kernels for instance.
Fix#4226
Adds try-catch-statement with diagnostic errors in Dhcp_server::free_ip in
order to guard against exceptions from the underlying bit allocator. These
exceptions should never happen given that the router is programmed correctly
and always feeds Dhcp_server::free_ip with sane arguments (which it should).
However, should this not be the case, we can assume that the failed IP freeing
indicates that the IP isn't allocated anyway and it's fine to continue using
the router. Furthermore, IP allocations are a mere client service and not
relevant for the integrity or safety of the router.
Ref #4200
When Interface::handle_config_3 (third step of applying a new configuration to
interfaces) tried to detach the interface from the current IP config because
the old and new IP config differed, it did so using the new domain. The former
steps of the reconfiguration already installed the new domain reference at the
interface. Therefore, also the DHCP server of the new domain was used. This,
however caused uncaught exceptions because detaching from an IP config
includes dissolving all DHCP allocations. This dissolving of DHCP allocations
now operated on a DHCP server (the one of the new domain) that wasn't related
to the allocations and, in the worst case, caused an uncaught exception
because the IPs were out of its range.
That said, this commit ensures that detaching an interface from an IP config
is always done on the domain from which the IP config originated. Normally,
this is the domain the interface is attached to. But in the case of
Interface::handle_config_3, it is another - the former domain the interface
was attached to.
The commit also adapts the nic_router_dhcp_* tests in a way that they
reconfigure the router in a way that would trigger the uncaught exception
without the fix.
Fixes#4200
Adapts Dir_file_system::open_composite_dirs in a way that it returns "success"
when the leaf node of the path is an empty directory but "lookup failed", as
usual, if one of the other directories on the way to the leaf node is empty.
I couldn't find a technical reason why we used to return "lookup failed" when
only the leaf node was empty.
The commit also adds a test for en empty root directory and empty
sub-directories to the fs_query run script.
Fixes#4198
Enable watching files via the inotify interface of the Linux Kernel.
Delivery of watches to components is staggered in order to prevent an
overflow of the ACK queue in cases when a lot of changes are made to the
file system from the Linux side.
Fixes#4070
A reset domain can consist of one or several reset-pins
denoted by name that are assigned to a device.
When the device gets acquired via the Platform RPC API,
the pins are de-asserted, and asserted again when the
device gets released.
A configuration looks like the following:
<device name="mipi_dsi>
<reset-domain name="mipi_dsi_pclk"/>
...
</device>
Fixes#4171
Introduces the notion of a transaction that consists of one or more
messages. Whereby a message has a read or write direction and consists
of one or more bytes.
Issue #4170Fixes#4169
Report via platform_info the capabilities of the kernel, e.g. ACPI and MSI.
With the commit the try-catch pattern on IRQ session creation by the platform
driver is avoided.
Issue #4016
This patch moves the utility from the app/text_area to os/vfs.h to make
it easier to use by other components. By hosting the 'New_file' as a
friend alongside the 'Directory', we can now pass a 'Directory' as
constructor argument, which is consistent with other utilities such as
'File_content'.
As a further improvement, the new version supports the implicit creation
of the directory hierarchy leading to the new file.
Issue #4032
For fs_file_systems, reads are limited to the size of the packets from the
File_system session. Hence, we cannot read the large files in one go.
This fix is particularly helpful for fonts_fs, as it enables including font
files from a File_system.
genodelabs/genode#4135
When a DHCP packet is printed out, it first tries to determine the most
specific message type from the DHCP options and print its human-readable name
right after the protocol name. If finding the message type fails, the less
specific opcode is printed instead, but also in a human-readable way.
Fixes#4131
This new runscript demonstrates how a file can be overwritten by vfs
import with the flag overwrite set to false. This is due to a bug
in lx_fs that is not propagating an ernno EEXIST syscall error.
Issue genodelabs#4104
This commit introduces a fix for lx_fs to propagate errno EEXIST error.
This prevents vfs <import overwrite="false"> to overwrite an imported
file, if it already exists, without the overwrite flag set to true.
Issue genodelabs#4104
With the update to GCC 10, the compiler stopped with an error when compiling
places where a MAC address is copied from outside into a packed object using
the Net::Netaddress::copy method (e.g. in
Net::Arp_packet::dst_mac(Mac_address)):
! error: writing 6 bytes into a region of size 4 [-Werror=stringop-overflow=]
While trying to find a clean solution for this error, I found posts on
gcc.gnu.org and github that stated that the size calculations that cause these
errors are incorrect. Indeed, I could verify that the actual size of the two
regions was static and exactly the same in places were the error occured.
Furthermore, I couldn't find a way of making it more clear to the compiler
that the sizes are the same. By accident, we found that using the address of
the first element of the array that forms the second region instead of the
array address itself, somehow circumvents the error.
Fixes#4109
With the update to GCC 10 the compiler used to warn when using the internet
checksum functions on packet classes (like in
Net::Ipv4_packet::update_checksum):
warning: converting a packed ‘Net::[PACKET_CLASS]’ pointer
(alignment 1) to a ‘const uint16_t’ {aka ‘const short
unsigned int’} pointer (alignment 2) may result in an
unaligned pointer value
Apparently, the 'packed' attribute normally used on packet classes sets the
alignment of the packet class to 1. However, for the purpose of the
internet-checksum functions, we can assume that the packet data has no
alignment. This is expressed by casting the packet-object pointer to a pointer
of the new packed helper struct 'Packed_uint16' that contains only a single
uint16_t member before handing it over to the checksum function (instead of
casting it to a uint16_t pointer).
Ref #4109
The NAT feature of the NIC router used to prefer re-using source ports that
have been freed recently. From an external server's perspective, if a client
dies and restarts, chances are high that the new connect arrives with the same
source-IP/source-port as the old connection. The server has to forcefully reset
the connection. If that happens a lot, the server may even start to ignore
further connections from this IP/port combination for a while as a mitigation.
This patch adds a continuous counter feature that makes sure that every new
port allocation will increment and result in a port that hasn't been used for a
long time.
The NAT feature of the nic_router is now more in line with RFC 6056 chapter 4.
Ref #4086
KEY_UNKNOWN is a collective symbols for all unknown keycodes.
Remapping thus requires iterating through all corresponding codes
instead of only applying the policy to the first match.
Issue genodelabs#4069
Introduce a new _overflowed state variable to indicate whether the
horizontal boundary was reached already and to omit subsequent character
output.
This state is necessary to maintain a valid cursor position at all
times. The _overflowed attribute is reset once the cursor is moved into
a valid position again.
To harmonise the bounds checking for _cursor_pos modifications, the
`constrain()` method was added.
Fixesgenodelabs/genode#4093
Also fixes a bug in `vpa()` and `vpb()` which moved the cursor
horizontally instead of vertically.
* The device XML information dataspace is only provided,
when the client's policy states `info="yes"`
* The device XM information gets changed to include the
physical resource names (I/O memory and IRQ addresses)
instead of virtual ids and page offset
Fix#4077
This is a follow-up fix for "Streamline platform-device API on ARM".
There is an ambiguity of the 'local_addr' method between the inherited
'Attached_dataspace' and the local declaration, which results in the
double application of the sub-page Range::start.
Issue #4075
This API rework eases the access to memory-mapped I/O registers and
interrupts when using the platform driver. It introduces the notions of
- Platform::Device - one device obtained from a platform session
- Platform::Device::Mmio - locally-mapped MMIO registers of a device
- Platform::Device::Irq - interface for receiving device interrupts
The patch touches several drivers. Some drivers would require a
significant structural change to adopt the new API (e.g., net/virtio,
dde_linux drivers, imx gpio). In these cases, the patch adds
compatibility shims meant to be temporary. In other cases (e.g., imx
i2c), the adaptation was simple enough to carry through.
Fixes#4075
These messages pollute the boot log of Sculpt OS when ROM modules are
requested for files of the config fs before the sculpt manager has
created their first version.
This patch extends the 'Platform_session::alloc_dma_buffer' interface
with a 'Cache' argument that corresponds to the argument accepted by
'Ram_allocator::alloc', which is used by the platform driver under the
hood.
Since the x86 platform driver used to be hardwired to allocate DMA
buffers as UNCACHED, I adjusted all drivers by specifying the UNCACHED
argument. Right now, this is needed as a hint for core to steer the
allocation of I/O page tables. Once we eliminate the need for such hints
(by introducing an explicit 'Region_map::attach_dma' operation), we can
revisit the drivers individually because cached DMA buffers should
generally be fine on the x86 architecture.
Issue #2243
This change avoids many repetetive Genode:: prefixes, making the code
easier to read. The patch also includes a few consistency fixes
regarding include guards and file headers. It also renames
Platform_device::String to Platform_device::Device:name.
Issue #2243
This patch adds the designated alternative to Dataspace::phys_addr to
the platform-session interface. Under the hood, the platform driver
still calls Dataspace::phys_addr but it should eventuelly become the
only caller before we can abolish this function.
Issue #2243
This commit optimizes the 'Child::resolve_session_request'
implementation by introducing an internal 'Route_model' for quickly
traversing routing rules instead of parsing XML on each session request.
Fixes#4068
This commit replaces the hand-crafted config processing by the use of
the 'List_model' utility. This has the following advantages:
- The parsing follows a common formalism that makes the code
easier to maintain and to understand. Several parts of the code
had to be changed (for the better) to make it fit the list model
approach. E.g., the child states have become more expressive
and logical.
- In the common case, the XML data is traversed only once, which
increases the parsing speed in dynamic scenarios.
- The code becomes easier to optimize. In particular, the patch skips
the re-evaluation of the session routing if no service is affected
by the config change.
The patch also revisits the init test by removing overly long sleep
phases and extending a few sleep phases that were too short when
executing the test on Qemu.
Issue #4068
This patch changes the 'alloc_aligned' interface as follows:
- The former 'from' and 'to' arguments are replaced by a single
'range' argument.
- The distinction of the use cases of regular allocations vs.
address-constrained allocations is now overed by a dedicated
overload instead of relying on a default argument.
- The 'align' argument has been changed from 'int' to 'unsigned'
to be better compatible with 'addr_t' and 'size_t'.
Fixes#4067
This patch avoids the RTC driver's aggressive polling during the
(CPU-bounded) boot of Sculpt OS. As the RTC is not needed during bootup,
this patch reduces the boot time (on Qemu) by 2-4 seconds.
Fixes#4065
