From driver point of view no differance between rtl8367b and rtl8367s
if it connected through EXT2 (rgmii only).
So this trivial patch add some identification and initialization only.
SGMII/HSGMII mode for EXT1 is not implemented for the sake of patch
clairity.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
[Fix code format]
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[add flags to separate chip_num/chip_id detection; drop error print in
rtl8367b_init_regs, drop unnecessary info prints, code style fixes]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[rebase; use MII macros]
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[code optimization]
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Set root=/dev/fit0 cmdline parameter as the kernel won't mount rootfs
otherwise after the change from the FIT partition parser to the fitblk
driver which replaces it.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel warns about comparision of different types without cast when
building the fitblk driver on 32-bit platforms.
Fix this by using `min_t(size_t, ...`.
Fixes: 8fc5457869 ("kernel: add pending fitblk uImage.FIT sub-image block driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623.
Introduce boot device selection for fitblk's /chosen/rootdisk
handle, similar to how it is already done on MT7622, MT7986 and MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
**Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem.
SoC Type: Qualcomm IPQ4019
RAM: 512 MiB
Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC)
Bootloader: U-Boot
Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink
WiFi class AC2200:
- radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels
- radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz
- radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on.
Ethernet: 2x1GbE (WAN/LAN1, LAN2)
LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white
USB ports: No
Buttons: 2 Reset and SYNC(WPS)
Power: 12 VDC, 2,5 A
Connector type: Barrel
OpenWRT Installation
1. Simplest way is just do upgrade from webpage with *factory.img
2. You can also do it with standard tool for Netgear's debricking - NMPRFlash
3. Most advanced way is to open device , connect to UART console and :
- Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10)
- Connect serial console (115200,8n1) to UART connector
- Connect TFTP server to RJ-45 port
- Stop in u-Boot and run u-Boot command:
> setenv serverip 192.168.1.10
> set fdt_high 0x85000000
> tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb
> bootm 0x83000000
- Login via ssh
- upload or download *sysupgrade.bin ( like wget ... or scp transfer)
- Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”)
Back to Stock
- Download firmware from official Netgear's webpage , it will be *.img file after decompressing.
- Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash )
Open the case
- Unscrew nuts and remove washers from antenna's conectors.
- There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it
- Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that.
- PCB is screwed with 4Pcs of Torx T10 screws
- Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires)
- On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg )
BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org.
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
Replace ARM bootloader patch with pending upstream version. The patch
got reviewed upstream and tested on a Netgear R7800.
This fix a problem with the ARM decompressor and permits to use
AUTO_ZRELADDR without having to hardcode PHYS_OFFSET as the bootloader
now correctly parse the memory modes in the appended DTB.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
All mt7622 board previously using the FIT partition parser have been
converted to use the fitblk driver:
6aec3c7b5b mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build
41c053141e mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblk
208f6c1232 mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblk
Remove the now no longer needed FIT partition parser from builds for
mt7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add node to support the QUP4 SPI controller inside of IPQ8074.
Some devices use this bus to communicate to a Bluetooth controller.
Signed-off-by: Robert Marko <robimarko@gmail.com>
add back WIFI eprom addresses pointer in mt7621_dlink_dir-xx60-a1.dtsi
Change MAC address pointer from factory_e006 to factory_e000 + 3
same as used in D-link firmware 1.11 DIR-1960-A1
DIR-1960-A1,DIR-2640-A1,DIR-2660-A1,DIR-3060-A1
Clean-up MAC addresses in D-Link NOR devices DTS's
Change WIFI MAC Addressees to the same as NAND cousins macaddr_factory_e000 + ?
as later devices don't have the MAC address in factory configuration
same as used in D-Link firmware 1.30 DIR-878-A1
DIR-867-A1,DIR-878-A1,DIR-878-R1,DIR-882-A1,DIR-882-R1,DIR-1935-A1
* D-link software differs between source of wan address
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Now we support parsing the color and function properties.
Ref: e814acc599 ("base-files: support parse DT LED color and function")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
[port 8ed390a (qualcommax: set correct PHY mode for port 0-4) to ipq60xx]
Port 0-4 have the mode set to SGMII instead of PSGMII. Now that we use
he upstream qca807x driver, this conflicts with the qca SSDK driver
that expects the mode to be PSGMII as for not integrated driver, it does
refer to the real PHY mode.
Update the entry for port 0-4 to PSGMII to solve warning from qca SSDK
in ipq6018-ess.dtsi.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Hardware
--------
RockChip RK3566 ARM64 (4 cores)
- up to 8GB LPDDR4X
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- 10/100/1000 Base-T
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Simple AQR hack patch has been merged upstream, hence we can drop it from
hack directory and move it to backport.
The patch for 5.15 are correctly reworked to align to outdated API.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address)
to "enterprise" edition, and it was added as a "new" board in upstream
kernel.
This patch switched to use that upstreamed dts and removed local
EEPROM patch.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Ubiquiti WA devices with newer hw version (sold 2023)
require UBNT_VERSION to be at least 8.7.4, otherwise
the image is rejected.
For consistency, also increase version number for XC devices.
Signed-off-by: Martin Garbe <monomartin@opennet-initiative.de>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Fix style of nvmem cell names in the device tree of the GL.iNet MT-2500.
Fixes: 49ed52b862 ("mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMC)"
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Recent OEM firmware versions test the version number embedded in the uimage
"name" header field. The exact restricton is unknown, but "7.0.8.4" seems
to be the lowest number accepted on a GS110TPPv1 which already has that
version or higher.
A "9.9.9.9" version is accepted as valid by the GS110TPPv1 OEM firmware,
and considered both unique enough to identify an OpenWrt image and
moderately future proof against OEM version bumps.
This change is also boot tested on a GS108Tv3 with
"BOOT Loader Version 1.0.0.2 (2018-08-31 17:05:26 UTC)"
to verify that it doesn't break boot on older hardware.
Link: https://forum.openwrt.org/t/72510/58
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Import patch to make sure SGM_REG_SEL clock is always enabled as it
seems that more registers than just SGMIISYS0 and SGMIISYS1 are
depending on that clock being enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we can reference MMC partitions in device tree, use that
to get rid of Wi-Fi EEPROM and MAC address setup in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use device_set_node to make sure OF node gets assigned on block
devices to be used as NVMEM providers. While block partitions were
already working fine as NVMEM providers, bare block devices such as
mmcblk0boot1 will not work without this change.
Fixes: fc153aa8d9 ("kernel: import pending patches adding support for NVMEM on UBI and MMC")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
UNIPHY2 on the WAX630 is connected to a QCA8081 PHY which is only 2.5G and
it does not support using USXGMII at all but rather only SGMII or SGMII+.
Tested-by: Kristian Skramstad <kristian+github@83.no>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove inaccurate compatible string 'mediatek,mt7986-ethsys' which
results in the wrong clock driver probing on MT7981 with Linux 6.1 and
ends up freezing the system once WED is used.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by
host system. With built-in drivers this doesn't work in OpenWrt /
embeddded as filesystem isn't available during PHY probe. That results
in delays like:
[ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld
[ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110)
Switch to module to postpone PHY probe to init state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14
Since this is not Qnap 301W specific lets fix it subtarget wide by
declaring the correct PHY mode for 10G AQR-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14
So, lets fix 10G AQR ports by declaring the correct PHY mode.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also here build fails due to increased kernel size.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Due to increased kernel size the build currently fails if including
the MT7622 rfb1 (UBI). Skip it for now until there is a better
solution (such as replacing the bootloader and changing the flash
layout).
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Include the needed Ethernet PHY driver module for the BananaPi R3 mini.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Reported-by: BPI forum user nezar_taima
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
One of the pins requiered by M.2 slot is conflict with spi1,
however, spi1 seems unused so simply disable it for now, this
matches the factory behavior [1].
1. 9bd78779f2
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Conversion to new LED color/function format and drop label format.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property can be
removed in favor of the new format.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This commit fixes the alphabetical order in 02_network.
The 2 deco devices in ath79_setup_interfaces() were in the wrong place.
Signed-off-by: Foica David <superh552@gmail.com>
Since we can configure the PHY LED of the qca8081,
add a configuration for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The dts of Arcadyan AW1000 forgot to convert qca807x PHY
to PHY package implementation. This commit fix it.
Fixes: 0ab4b92 ("qualcommax: convert qca807x PHY to PHY package implementation")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Generate ubinized image as ARTIFACT and make use of now available
generic 'ubinize-image' build step intended for that purpose.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix NAND flash layout which was out-of-sync with the definition in
ARM TrustedFirmware-A which expects UBI to start at 0x200000.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The U-Boot binary for the RAVPower RP-WD009 has been renamed.
In order to be uniform with all other U-Boot binaries generated the SoC type has been prepended.
Set that new name also in the image build recipe for that device in order to fix build.
Fixes: 927334a8f7 ("uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
update the default network configuration for Gateworks Ventana boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Hardware specification
----------------------
SoC: MediaTek MT7986A 4x A53
Flash: 128MB SPI-NAND, 8GB eMMC
RAM: 2GB DDR4
Ethernet: 2x 2.5GbE (Airoha EN8811H)
WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
Interfaces:
* M.2 Key-M: PCIe 2.0 x2 for NVMe SSD
* M.2 Key-B: USB 3.0 with SIM slot
* front USB 2.0 port
LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
Button: Reset, internal boot switch
Fan: PWM-controlled 5V fan
Power: 12V Type-C PD
Installation instructions for eMMC
----------------------------------
0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt
running there).
1. Write GPT partition table to eMMC
Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to
the device /tmp using scp and write it to /dev/mmcblk0:
dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0
2. Reboot (to reload partition table)
3. Write bootloader and OpenWrt images
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate partitions:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5
sync
4. Remove the device from power, set boot switch to eMMC and boot into
OpenWrt. The device will come up with IP 192.168.1.1 and assume the
Ethernet port closer to the USB-C power connector as LAN port.
5. If you like to have Ethernet support inside U-Boot (eg. to boot via
TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1:
echo 0 > /sys/block/mmcblk0boot1/force_ro
dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1
dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1
Installation instructions for NAND
----------------------------------
0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there
by instructions above. Using stock rom or immortalwrt does NOT work!)
1. Write things to NAND
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate locations:
mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0
ubidetach -m 1
ubiformat /dev/mtd1
ubiattach -m 1
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip)
ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static
ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
cd /lib/firmware/airoha
cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static
ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976
ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
3. Remove the device from power, set boot switch to NAND, power up and
boot into OpenWrt.
Partially based on immortalwrt support for the R3 mini, big thanks for
doing the ground work!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add PHY driver for Airoha EN8811H PHY and package it as kernel module.
The PHY needs to load firmware from rootfs, so there is no point in
having the driver built-into the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Firmware for the built-in 2.5G Ethernet PHY of the MediaTek MT7988 SoC
is now part of linux-firmware, so we can package it.
Only a single file is needed with recent driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Switch to all-UBI layout on SPI-NAND
* use fitblk driver instead of uImage.FIT partition parser
* adapt sysupgrade
* bump COMPAT_VERSION
Remove BROKEN mark now that all needed changes are done.
Boards running images generated before this commit will require
full reflash of the bootloader, re-install from SD card is the
easiest way to achieve that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add environment settings for the BananaPi BPI-R4 router board which
can boot from (and store its bootloader environment on) micro SD card,
SPI-NAND and eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SOC: MediaTek MT7988A (4x Cortex-A73)
RAM: 4 GiB DDR4
Flash: 128 MiB Winbond SPI-NAND
MMC: 8 GiB eMMC *or* microSD (cannot be used both)
ETH: 4x 1GE (1x WAN, 3x LAN)
2x SFP+ (10G, 5G, 2.5G, 1G)
USB: on-board USB 3.2 4-port hub
1x USB 3.2 port (type A connector)
1x M.2 for 4G/5G modem
2x mPCIe for additional modems
WiFi: optional MediaTek MT7996 Wi-Fi 7 module
(using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)
Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).
2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.
3. Switch to boot from SPI-NAND and install to eMMC.
Known issues
------------
- The RST button is hard-wired to the SoC reset and can't be read
from software. This can be changed by modifying the board (ie.
moving a 0-ohm resistor). However, in order to maintain compatibility
with the board as it comes from factory the button isn't used by
OpenWrt and the WPS button is used as factory/reset button instead.
- various small things still need to be fixed in DT
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch from MediaTek SDK which allows using the third
PCIe host controller of the MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add UART pinctrl group for using only pins 80 and 81 for uart1.
This is needed on the BPi-R4 as RTS/CTS signals are used for other
on-board functions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace previous patch adding paths and SerDes modes with patch series
pending upstream adding dedicated drivers for XFI T-PHY and USXGMII PCS,
extends LynxI PCS to be a standalone platform driver and as a consequence
makes much less changes to the actual Ethernet driver mtk_eth_soc.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport almost 50 commits from upstream Linux to improve thermal
drivers for MediaTek SoCs and add new LVTS driver for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let's pick a bunch of useful phylink changes which allow us to keep
drivers in sync with mainline Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add 'fitblk' driver to replace the rejected/deprecated uImage.FIT
partition parser.
To use the new driver, add phandle /chosen/rootdisk and point it to
the MTD partition, UBI volume or block device holding the uImage.FIT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Similar to supporting nvmem-layouts on MTD devices, also allow referencing
UBI and MMC devices in DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to allow gradually migrating the boards currently using the
uImage.FIT partition (deprecated/rejected) parser to the new fitblk
driver, skip the partition parser code in case the new fitblk driver
(which serves the same purpose) is used.
As an indicator for the use of the new fitblk driver, check if the
/chosen/rootdisk property is present in the Device Tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The partition parser approach has been rejected upstream, it will be
replaced by a small block driver which is the solution suggestion by
upstream maintainers.
As the partition parser has only been used by the mediatek target, as
a first step, move it there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport two commits from Linux 6.3 wiring up device node parents of
ubi devices (pointing to their MTD parent) as well as ubiblock devices
(poiting to their parent UBI volume).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Convert qca807x PHY to new implementation like for other devices.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Now that Malibu (QCA807x) PHY is using the upstream driver, we dont need
support to define address of the first PHY in package, so remove the
malibu_first_phy_addr DTS property.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that QCA807x interface mode check was upstreamed, use the upstreamed
version and mark it as such.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use order described as preferred in DTS Coding Style. Mostly just move
"compatible", "reg", "ranges" and "status" properties.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
PoE devices in the realtek target have the possibility to add PSE info
to the board description via 02_network. Make this available for all
targets, by moving the uci_set_poe() function to the globally available
uci-default.sh script.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
uci_set_poe() now performs two duties: filtering the list of device
ports to exclude non-PoE ports, and generating the PoE related device
config.
Extract the port filtering to an external function, which is made a bit
more readable by the use of 'sort -V [-r] | uniq -u' to filter duplicate
entries out of a (reverse) version sorted list.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The ZyXEL XGS1250-12 has a chassis fan. The fan is positioned perfectly to
provide additional cooling to the Aquantia NBase-T phys. Testing has shown
that the phys can reach temperatures upwards of 72 degrees Celsius quite
easily at about 20 degrees Celsius ambient.
Support the chassis fan to give the phys a bit of extra cooling.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This reverts commit 131e41614d.
Sadly it makes menuconfig fail with
tmp/.config-package.in:171: glob failed: No files found "feeds/base/utils/busybox/Config.in"
make: *** [/usr/src/openwrt/include/toplevel.mk:136: menuconfig] Error 1
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building a package in the build system or the SDK results in different
values for the `SOURCE` property, it's either `packages/<package name>`
or `feeds/base/<package name>`. The reason is that the SDK handles
`openwrt.git` as an external feed called while the build system contains
the *base* packages directly.
Since packages created with either method are (ideally) the same (bit
for bit), align the content of SOURCE. To do so this commit creates a
symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE
when building from inside the build system.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Currently, we are checking whether the PHY package mode matches the
individual PHY interface modes at PHY package probe time, but at that time
we only know the PHY package mode and not the individual PHY interface
modes as of_get_phy_mode() that populates it will only get called once the
netdev to which PHY-s are attached to is being probed and thus this check
will always fail and return -EINVAL.
So, lets move this check to .config_init_once as at that point individual
PHY interface modes should be populated.
Fixes: 16364e4100 ("generic: 6.1: backport QCA807x PHY patches")
Signed-off-by: Robert Marko <robimarko@gmail.com>
This Qualcomm Gigabit phy driver was mistakenly added because
MT76x8 does not support external phy, and it only supports max
100M full duplex speed.
Fixes: cadf517107 ("ralink: add support for mt7628")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Xiaomi AX9000 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Xiaomi AX3600 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Also enable CONFIG_PHYLIB_LEDS to actually expose the PHY LEDs if
defined in DT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert every qca807x PHY definition in DT to new PHY package
implementation to correctly support applying fixup for the correct PHY
mode.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Port 0-4 have the mode set to SGMII instead of PSGMII. Now that we use
the upstream qca807x driver, this conflicts with the qca SSDK driver
that expects the mode to be PSGMII as for not integrated driver, it does
refer to the real PHY mode.
Update the entry for port 0-4 to PSGMII to solve warning from qca SSDK
in ipq8074-ess.dtsi.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
IPQ807x have integrated qca8074 PHY supported by the upstream qca807x driver.
Enable it to use it instead of the downstream qca SSDK variant.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adapt patches to new Upstream QCA807x PHY driver.
Rework the PHY patch to new PHY Package nodes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport QCA807x PHY patches merged upstream that introduce the new
concept of PHY package.
Also add in generic config the new Kconfig CONFIG_QCA807X_PHY.
All affected patch automatically refreshed with make
target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport Aquantia PHY endianess patch. While the current implementation
works ok for Little-Endian targets, backport patch to prevent any kind
of malfunction if in the future we will have Big-Endian target with
Aquantia PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit d737ae99cb ("qualcommax: Fix Buffalo WXR-5950AX12 Ethernet
DTS") reverted the switch bmp to the original OEM definition and
added the malibu_first_phy_addr property.
Problem is that OEM bmp definition is wrong and actually doesn't make sense,
probably caused by copy-paste of the QCOM reference DTS without actually
setting real values. What actually fixed the regression was adding the
malibu_first_phy_addr as without it the MALIBU PHY was actually not
correctly configured and the Aquantia PHY were actually configured as
MALIBU PHY.
Fix all these wrong PHY definition.
The BPM is reverted and the following fixes are applied:
- Drop ESS_PORT1 as it's not actually attached in HW.
- Move ESS_PORT5 AGAIN from lan to wan. This refer to the first Aquantia
PHY that is labelled "wan"
- Move ESS_PORT6 AGAIN from wan to lan. This refer to the second
Aquantia PHY that is labelled "lan1".
Also PHY tag in MDIO node are renumbered to start from 0 following the
tagging standard used also in other dts and the not attached one (reg
0x18 and reg 0x1c) are correctly dropped.
Definition for port@1 in phyinfo is dropped as it doesn't exist.
dp nodes are updated to reference the new PHY tag numbering.
Fixes: d737ae99cb ("qualcommax: Fix Buffalo WXR-5950AX12 Ethernet DTS")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The NWA50AX Pro only has a eth0 interface for its only ethernet port.
Use this port for preinit.
Fixes non-working network in failsafe mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
u64_stats_init() has been unable to handle NULL pointer since
6.1 kernel. This patch fixes kernel oops on mt76x8 and rt305x
sub-target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In the 5.15 kernel, we use the staging driver version instead of the
downstream file.
Fixes: 88d982e3bd ("ramips: 6.1: mt7621-dma: add hsdma driver to files")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Fixes errors in the form of:
make[9]: Entering directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7620/linux-6.1.77'
CC drivers/net/ethernet/ralink/mtk_eth_soc.o
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1368:51: warning: passing argument 2 of 'of_get_mac_address' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
1368 | of_get_mac_address(priv->dev->of_node, dev->dev_addr);
| ~~~^~~~~~~~~~
In file included from drivers/net/ethernet/ralink/mtk_eth_soc.c:26:
./include/linux/of_net.h:16:59: note: expected 'u8 *' {aka 'unsigned char *'} but argument is of type 'const unsigned char *'
16 | extern int of_get_mac_address(struct device_node *np, u8 *mac);
| ~~~~^~~
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_probe':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1641:9: error: too many arguments to function 'netif_napi_add'
1641 | netif_napi_add(netdev, &priv->rx_napi, fe_poll, napi_weight);
| ^~~~~~~~~~~~~~
In file included from ./include/linux/etherdevice.h:21,
from drivers/net/ethernet/ralink/mtk_eth_soc.c:21:
./include/linux/netdevice.h:2611:1: note: declared here
2611 | netif_napi_add(struct net_device *dev, struct napi_struct *napi,
| ^~~~~~~~~~~~~~
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream commit f48dc6b96649 ("spi: Retire legacy GPIO handling") [0]
removed support using GPIOs as chip select. Fix it by replacing cs_gpio
with cs_gpiod.
[0] - f48dc6b966
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Change fe_hw_set_macaddr and the set_mac parameter to const to fix
errors in the form of:
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_set_mac_address':
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
174 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_hw_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1220 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c:1222:44: error: passing argument 2 of 'fe_hw_set_macaddr' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1222 | fe_hw_set_macaddr(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:155:75: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
155 | static inline void fe_hw_set_macaddr(struct fe_priv *priv, unsigned char *mac)
| ~~~~~~~~~~~~~~~^~~
cc1: all warnings being treated as errors
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped support for legacy driver [0]. Rewrite the driver like
the renesas pwm driver [1].
Fixes erros in the form of:
make: *** [/__w/openwrt/openwrt/openwrt/include/toplevel.mk:232: target/compile] Error 1
====== Make errors from logs/target/linux/compile.txt ======
| ^~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:107:19: note: (near initialization for 'mtk_pwm_ops.free')
drivers/pwm/pwm-mediatek-ramips.c:108:10: error: 'const struct pwm_ops' has no member named 'disable'
108 | .disable = mtk_pwm_disable,
| ^~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: error: initialization of 'int (*)(struct pwm_chip *, struct pwm_device *, struct pwm_capture *, long unsigned int)' from incompatible pointer type 'void (*)(struct pwm_chip *, struct pwm_device *)' [-Werror=incompatible-pointer-types]
108 | .disable = mtk_pwm_disable,
| ^~~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: note: (near initialization for 'mtk_pwm_ops.capture')
cc1: all warnings being treated as errors
[0] - 0829c35dc5
[1] - ec00cd5e63
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped slave_id in dai_dma [0]. So drop it also in the mt7620
support patch.
Fixes errors in the form of:
sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_init_dma_data':
sound/soc/ralink/ralink-i2s.c:452:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
452 | dma_data->slave_id = i2s->txdma_req;
| ^~
sound/soc/ralink/ralink-i2s.c:462:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
462 | dma_data->slave_id = i2s->rxdma_req;
| ^~
[0] - https://lore.kernel.org/r/20211122222203.4103644-3-arnd@kernel.org
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream changed in ed5c2f5fd10d ("i2c: Make remove callback return void")
the i2c driver's remove function to return no value. Adapt the driver code
to compile with 5.15 and 6.1 like it is done in other projects [0].
Fixes errors in the form of:
make[8]: Leaving directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-6.1.29'
CC drivers/pinctrl/pinctrl-aw9523.o
drivers/pinctrl/pinctrl-aw9523.c:1117:19: error: initialization of 'void (*)(struct i2c_client *)' from incompatible pointer type 'int (*)(struct i2c_client *)' [-Werror=incompatible-pointer-types]
1117 | .remove = aw9523_remove,
| ^~~~~~~~~~~~~
drivers/pinctrl/pinctrl-aw9523.c:1117:19: note: (near initialization for 'aw9523_driver.remove')
cc1: all warnings being treated as errors
[0] - https://gitlab.com/ddcci-driver-linux/ddcci-driver-linux/-/merge_requests/10/diffs
Signed-off-by: Nick Hainke <vincent@systemli.org>
Apply the "109-drivers-mt7621-dma-handle-error-from-device_reset.patch"
directly on the downstream maintained dma driver.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Commit 87dd67f496f7 ("staging: mt7621-dma: remove driver from tree")
removed the mt7621-dma driver. Maintain the driver downstream in the
folder of the other mediatek drivers.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Refresh kernel patches changed from the just introduced ipq60xx new
subtarget.
Patch automatically refreshed with make target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These recipes are generic and will be used for other subtargets, so lets
move them to the target Makefile so they can reused.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for the Qualcomm IPQ60xx SoC. WiFi support still has
to be handled and correctly fix hence this is currently marked as
source-only to have a solid base to progress on correct support of this
and hope Upstream QUIC publish newers ath11k drivers for this SoC.
Co-developed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ improve commit description, add SoB for Robert, make it source-only ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: a9e0d97e1f ("ipq40xx: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add dtb makefile target to targets list to permit correct working of
make target/linux/dtb
Fixes: c47532b1ea ("kernel-buildOnmk: add support for compiling only DTS")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
bmips has all the dt-bindings includes inside each SoC .dtsi files, so let's
move the new includes there instead of adding them to each board .dts files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 19c45b95db ("ramips: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 0c3f3eb229 ("lantiq: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 33e7962329 ("ipq806x: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch fixing kernel panic with mcast packets, patch is already
scheduled to be backported to stable kernels and will be dropped once
new stable kernel version are released.
Fixes: #14554
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The rtl93xx SoC supports both 1000Base-X and 10GBase-CR on its SerDes
interfaces. Enable dynamic switching between mac-signaled modes to
support 1000Base-X and 10GBase-CR on the SFP port.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This patch adds support for 1000Base-X and 10GBase-CR directly on the
SerDes lanes of rtl93xx SoCs.
This fixes SFP/SFP+ support on devices like the XSG1250-12.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
Backport patch to enable PHYLIB_LEDS kconfig dynamically instead of
having to select this config for every target that makes use of PHY LEDs
API.
All affected patch are automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_PHYLIB_LEDS is required in order for phylib to probe the DT for LEDs
attached to PHY-s.
Fixes: 75ad5c2 ("qualcommax: switch to qca8081 upstream PHY driver")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit daefc646e6 ("realtek: fix ZyXEL initramfs image generation")
fixed a shell expansion issue with zyxel-vers usage. Commit 045baca10b
("realtek: deduplicate GS1900 recipes") took care of this for the
rtl838x and rtl839x subtargets, but the single device officially
supported in rtl930x - the XGS1250-12 - was overlooked. This commit
updates the XGS1250-12 build recipe as well.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Add even more missing Kconfig for video-core introduced by recent fixup
to video kmods.
Fixes: 76b0d24157 ("kernel: modules: video: fix video-core for 6.1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport one patch merged upstream that prevent a deadlock for LED
netdev trigger and add a pending patch that fix kernel panic on
interface rename trigger notification with invalid dev.
Fixes: #14477
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing Kconfig for video-core introduced by recent fixup to video
kmods.
Fixes: 76b0d24157 ("kernel: modules: video: fix video-core for 6.1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linux 6.1 wraps core video drivers in a MEDIA_PLATFORM_DRIVERS submenu.
Enable that for 6.1 and add some new necessary undefines to
target/linux/generic/config-6.1 to avoid build failures.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds support for the Fritzbox 3490 device. It contains two
SoCs, one Lantiq with a 5GHz WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module which is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
- Without telephony or ISDN
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This adds support for the Fritzbox 5490/5491 devices. They contain
two SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module which is not supported with this commit.
Both devices have fiber WAN ports.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port Lantiq gswip switch,
4x 1000/100/10 port (additional qca8334 switch for 2 ports), Port 5 is
fixed and connected to the Wireless SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- AT 8033 based AON fiber port (5490) or GPON fiber port (5491)
Unsupported:
- DECT and ISDN telephony
- Two ethernet ports (on extra switch) and fiber port not working
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This adds support for the Fritzbox 7490 device. It contains two
SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module and is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
Unsupported:
- DECT and ISDN telephony
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The Fritzbox 3490, 5490 and 7490 devices have a Renesas µPD720202
USB3 PCIe device, which requires an endian switch for PCIe slave
devices. The flag and setting is not implemented in the available
patches. Since adding this setting would break other devices,
a DTB setting lantiq,switch-pcie-endianess is added for selective
enablement.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
Specifications:
lan: eth0
wan: eth1
Problem Description:
The lan wan port is reversed with the current machine.
Use eth0 as LAN port and eth1 as WAN port.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
The driver for the cellular modems serial interface and qmi was missing
from the default device packages. The driver is required to interact
with the modem using AT commands.
Signed-off-by: Jan Fuchs <jf@simonwunderlich.de>
Backport PHY package MMD patch merged upstream that add support for
writing MMD regs for the PHY package and support for writing to PHY
package at an offset.
All affected patches automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch converts ath10k calibration data to NVMEM format for
wave 1 devices with mtd ASCII MAC address. The "calibration"
NVMEM cell size is 0x844. All unportable MAC address settings
have been moved to '10_fix_wifi_mac' scripts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k calibration data to NVMEM format for
wave 1 devices with mtd binary MAC address. The "calibration"
NVMEM cell size is 0x844. The MAC addresses are assigned via dts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k calibration data to NVMEM format for
wave 1 devices with built-in MAC address. The "calibration"
NVMEM cell size is 0x844.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k pre-calibration data to NVMEM format for
wave 2 devices with mtd ASCII MAC address. The "pre-calibration"
NVMEM cell size is 0x2f20. All unportable MAC address settings have
been moved to '10_fix_wifi_mac' scripts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k pre-calibration data to NVMEM format for
wave 2 devices with mtd binary MAC address. The "pre-calibration"
NVMEM cell size is 0x2f20. The MAC addresses are assigned via dts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts ath10k pre-calibration data to NVMEM format for
wave 2 devices with built-in MAC address. The "pre-calibration"
NVMEM cell size is 0x2f20.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The ath10k driver will load both pre-calibration data and board-2.bin
if board-2.bin exists. So it's not necessary to remove it. And this
change won't increase jffs2 image size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Backport at803x split patches merged upstream to tidy things up for the
at803x PHY driver.
New Kernel config are introduced hence any user needs to be updated.
Downstream ipq40xx patch require rework to correctly move them to the
qcom specific PHY directory.
All affected patch automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Only bcm2708 and bcm2709 use "kernel.img" file name.
bcm2710 and bcm2711 use "kernel8.img" and bcm2712 uses "kernel_2712.img".
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Automatically detect boot partition instead of forcing /dev/mmcblk0p1.
This way users can still get /boot mounted when booting from USB.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add missing Rasoberry Pi 5 board_name to set_preinit_iface in order to get
ethernet working on failsafe mode.
Fixes: 8b63d9a ("bcm27xx: add new bcm2712 subtarget")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* fix switch ports with modes other than 1000M/Full
* set 32-bit dma_coherent_mask to get PPE to work with 4 GiB of RAM
* sync driver for built-in 1GE PHY with MediaTek SDK sources
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The qca8081 phy needs to set the reset delay time,
otherwise it will not be detected by the mdio bus.
Fixes: 75ad5c2 ("qualcommax: switch to qca8081 upstream PHY driver")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Switch to qca8081 upstream PHY. Update every device that have LEDs
attached to the qca8081 PHY to follow new way of defining the LEDs and
add original OEM configuration.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream patch adding more speed modes to LED netdev trigger.
Fixes: 2c39269b6e ("generic: 6.1: backport qca808x LED support patch")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport qca808x LED support patch merged upstream needed to drop
handling of it from the SSDK for ipq807x target.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[rmilecki: port to 5.15]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
They are unnecessary since ipq806x switched to DSA in
the commit 337e36e0ef.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Refresh HSGMII patch due to recent PHY backport that cause
compilation warning for case not handled in phy_interface_num_ports.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh 2.5G-SGMII patch due to recent PHY backport that cause
compilation warning for case not handled in phy_interface_num_ports.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In order to get rid of having to modify U-boot bootcmd and having U-boot
load the Aquantia PHY-s firmware lets use some of the free space on SPI-NOR
to add a second ethphyfw partition and be able to load AQR FW via NVMEM
cells.
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that the reset GPIO-s defined for the two AQR PHY-s are actually
reversed.
Manually testing confirmed that GPIO44 is actually reset GPIO of AQR at 0,
while GPIO59 is reset of AQR at 8:
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x00 0x00000000 down
0x08 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
root@OpenWrt:~# gpioset gpiochip0 44=0
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x08 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
root@OpenWrt:~# gpioset gpiochip0 44=1
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x00 0x00000000 down
0x08 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
root@OpenWrt:~# gpioset gpiochip0 59=0
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x00 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
root@OpenWrt:~# gpioset gpiochip0 59=1
root@OpenWrt:~# mdio 9*
DEV PHY-ID LINK
0x00 0x00000000 down
0x08 0x00000000 down
0x10 0x004dd0b1 down
0x11 0x004dd0b1 down
0x12 0x004dd0b1 down
0x13 0x004dd0b1 up
0x14 0x004dd0b1 down
0x15 0x04820a05 down
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have support for firmware loading via the kernel driver, it
makes sense to populate the firmware name as well, so if its present the
driver can load it.
In later patches, loading the FW via NVMEM will be added as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch adds support for Raspberry Pi 5.
Instead of using 16K pages like Raspberry Pi OS, OpenWrt uses 4K pages due to
incompatibilities with F2FS and other applications.
There are multiple RPi forum posts with different cases and users are forcing
kernel8.img to workaround them, which is the 64 bit kernel of the RPi 4.
However, this isn't possible in OpenWrt because we only ship one kernel and we
would have to add RPi 5 support to bcm2711 subtarget (RPi 4) for that
workaround to work in OpenWrt.
Specification:
- Processor Broadcom BCM2712 2.4GHz quad-core 64-bit Arm Cortex-A76 CPU,
with cryptographic extension, 512KB L2 caches per core, 2048KB L3 cache
Features:
- VideoCore VII GPU, supports OpenGL ES 3.1, Vulkan 1.2
- Dual 4Kp60 HDMI display output with HDR support 4Kp60 HEVC decoder
- LPDDR4X-4267 SDRAM 4GB and 8GB
- Dual-band 802.11ac Wi-Fi
- Bluetooth 5.0 / Bluetooth Low Energy
- microSD card slot, with support for SDR104 high-speed mode
- 2 x USB 3.0 ports
- 2 x USB 2.0 ports
- Gigabit Ethernet
- 2 x 4 lane MIPI camera/display
- PCIe 2.0 x1
- 5V/5A power via USB-C
- Raspberry Pi standard 40-pin header
- Real-time clock RTC
- Power button
Build system: x86_64
Build-tested: bcm2712
Run-tested: bcm2712/RPi5
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[Remove device variant, improve description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add support for BCM2712 (Raspberry Pi 5).
3bb5880ab3
Patches were generated from the diff between linux kernel branch linux-6.1.y
and rpi-6.1.y from raspberry pi kernel source:
- git format-patch linux-6.1.y...rpi-6.1.y
Build system: x86_64
Build-tested: bcm2708, bcm2709, bcm2710, bcm2711
Run-tested: bcm2710/RPi3B, bcm2711/RPi4B
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[Remove applied and reverted patches, squash patches and config commits]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Ubiquiti Rocket M XW is a single-band, 2x2:2 external Wi-Fi AP, with optional
GPS receiver, with two external RP-SMA antenna connections, based on
AR9342 SoC. Two band variants exists, for 2.4GHz and 5GHz band, usable
with the same image.
Specs:
- CPU: Atheros AR9342 MIPS SoC at 535MHz
- RAM: 64MB DDR400
- ROM: 8MB SPI-NOR in SO16W package, MX25L6408E
- Wi-Fi Atheros AR9342 built-in 2x2:2 radio
- Ethernet: Atheros AR8035 PHY, limited to 100Mbps speeds due to
magnetics
- Power: 24V passive PoE input.
Installation: please refer to Ubiquiti Bullet M2HP for documentation.
The device runs with exactly same image as the Bullet, and after fixes
in preceding commit, is fully functional again. Add the alternative name
to the build system.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Since commit 6f2e1b7485 ("ath79: disable delays on AT803X config init")
Ubiquiti XW boards equipped with AR8035 PHY suffered from lack of
outbound traffic on the Ethernet port. This was caused by the fact, the
U-boot has set this during boot and it wasn't reset by the PHY driver,
and the corresponding setting in device tree was wrong.
Set the 'phy-mode = "rgmii-txid"' at the ð0, and drop this property
from PHY node, as it is not parsed there. This causes the device to
connect using Ethernet once again.
Fixes: db4b6535f8 ("ath79: Add support for Ubiquity Bullet M (XW)")
Fixes: 6f2e1b7485 ("ath79: disable delays on AT803X config init")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Onboard AR8035 PHY supports 1000Base-T operation, but onboard
Ethernet magnetics do not. Reduce advertised link speeds to 100Mbps and
lower.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add support for loading Aquantia FW from NVMEM for Zyxel NBG7815
restoring correct functionality of the 10g port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch for ipq4019 MDIO MDC rate fix. The divisor was never
actually set resulting in the MDC rate running at a very low speed.
The same MDIO is used on ipq807x where Aquantia PHY are commonly used
where MDIO is used to load the PHY firmware. Running at higher speed is
required to make the firmware load faster as it does reduce load time
from 60+ second to 5-6 seconds.
Add as pending as upstream there seems to be some conflicts with quic
and me and it might take lots of time before this is effectively merged
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
