2016-04-01 07:11:48 +00:00
|
|
|
#
|
|
|
|
|
# MT7621 Profiles
|
|
|
|
|
#
|
|
|
|
|
|
ramips: add support for Beeline SmartBox GIGA
Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Nanya NT5CC128M16JR-EK
Flash: 128 MiB, Macronix MX30LF1G18AC
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7613BE): a/n/ac, 2x2
Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2)
USB ports: 1xUSB3.0
Button: 1 button (Reset/WPS)
PCB ID: DBE00B-1.6MM
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Downgrade stock (Beeline) firmware to v.1.0.02;
2. Give factory OpenWrt image a shorter name, e.g. 1001.img;
3. Upload and update the firmware via the original web interface.
Remark: You might need make the 3rd step twice if your running firmware
is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware
reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update.
Revert to stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:16 |
| WAN | label + 1 | *:17 |
| 2g | label + 4 | *:1a |
| 5g | label + 5 | *:1b |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Notes
-----
1. The following scripts are required for the build:
sercomm-crypto.py - already exists in OpenWrt
sercomm-partition-tag.py - already exists in OpenWrt
sercomm-payload.py - already exists in OpenWrt
sercomm-pid.py - new, the part of this pull request
sercomm-kernel-header.py - new, the part of this pull request
2. This device (same as other Sercomm S2,S3-based devices) requires
special LZMA and LOADADDR settings for successful boot:
LZMA_TEXT_START=0x82800000
KERNEL_LOADADDR=0x81001000
LOADADDR=0x80001000
3. This device (same as several other Sercomm-based devices - Beeline,
Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing
real partition offsets, which may differ from device to device
depending on the number and location of bad blocks on NAND.
"fixed-partitions" is used if the partition map is not found or
corrupted. This behavour (it's the same as on stock firmware) is
provided by MTD_SERCOMM_PARTS module.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
|
|
|
include ./common-sercomm.mk
|
2020-01-29 17:21:53 +00:00
|
|
|
include ./common-tp-link.mk
|
|
|
|
|
|
2020-01-21 20:54:50 +00:00
|
|
|
DEFAULT_SOC := mt7621
|
|
|
|
|
|
2023-04-09 19:47:58 +00:00
|
|
|
DEVICE_VARS += ELECOM_HWNAME LINKSYS_HWNAME DLINK_HWID
|
2017-07-23 19:06:44 +00:00
|
|
|
|
ramips: add support for D-Link COVR-X1860 A1
The COVR-X1860 are MT7621-based AX1800 devices (similar to DAP-X1860, but
with two Ethernet ports and external power supply) that are sold in sets
of two (COVR-X1862) and three (COVR-X1863).
Specification:
- MT7621
- MT7915 + MT7975 2x2 802.11ax (DBDC)
- 256MB RAM
- 128 MB flash
- 3 LEDs (red, orange, white), routed to one indicator in the top of the device
- 2 buttons (WPS in the back and Reset at the bottom of the device)
MAC addresses:
- LAN MAC (printed on the device) is stored in config2 partition as ASCII (entry factory_mac=xx:xx:xx:xx:xx:xx)
- WAN MAC: LAN MAC + 3
- 2.4G MAC: LAN MAC + 1
- 5G MAC: LAN MAC + 2
The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1
Flashing via OEM Web Interface:
- Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-factory.bin via the OEM web interface firmware update
- The configuration wizard can be skipped by directly going to http://192.168.0.1/UpdateFirmware_Simple.html
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks red
- Open a Chromium based browser and goto http://192.168.0.1
- Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks red
- Open a Chromium based browser and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/openwrt/firmware-utils/blob/master/src/dlink-sge-image.c and https://raw.githubusercontent.com/openwrt/firmware-utils/master/src/dlink-sge-image.h
- Compile a binary from the downloaded file, e.g. gcc dlink-sge-image.c -lcrypto -o dlink-sge-image
- Run ./dlink-sge-image COVR-X1860 <OriginalFirmware> <OutputFile> -d
- Example for firmware 102b01: ./dlink-sge-image COVR-X1860 COVR-X1860_RevA_Firmware_102b01.bin COVR-X1860_RevA_Firmware_102b01_Decrypted.bin -d
The pull request is based on the discussion in https://forum.openwrt.org/t/add-support-for-d-link-covr-x1860
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit 0a18259e4aa361cd9e5848c038be4b9f4e3bfcc6)
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
2023-11-03 10:22:02 +00:00
|
|
|
define Build/append-dlink-covr-metadata
|
|
|
|
|
echo -ne '{"supported_devices": "$(1)", "firmware": "' > $@metadata.tmp
|
|
|
|
|
$(MKHASH) md5 "$@" | head -c32 >> $@metadata.tmp
|
|
|
|
|
echo '"}' >> $@metadata.tmp
|
|
|
|
|
fwtool -I $@metadata.tmp $@
|
|
|
|
|
rm $@metadata.tmp
|
|
|
|
|
endef
|
|
|
|
|
|
2022-04-28 18:24:07 +00:00
|
|
|
define Build/arcadyan-trx
|
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-01-05 13:11:56 +00:00
|
|
|
echo -ne "hsqs" > $@.hsqs
|
2022-04-28 18:24:07 +00:00
|
|
|
$(eval trx_magic=$(word 1,$(1)))
|
|
|
|
|
$(STAGING_DIR_HOST)/bin/otrx create $@.trx -M $(trx_magic) -f $@ \
|
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-01-05 13:11:56 +00:00
|
|
|
-a 0x20000 -b 0x420000 -f $@.hsqs -a 1000
|
|
|
|
|
mv $@.trx $@
|
|
|
|
|
dd if=/dev/zero bs=1024 count=1 >> $@.tail
|
|
|
|
|
echo -ne "HDR0" | dd of=$@.tail bs=1 seek=$$((0x10c)) count=4 \
|
|
|
|
|
conv=notrunc 2>/dev/null
|
|
|
|
|
dd if=$@.tail >> $@ 2>/dev/null
|
|
|
|
|
rm $@.hsqs $@.tail
|
|
|
|
|
endef
|
|
|
|
|
|
2021-03-02 05:10:14 +00:00
|
|
|
define Build/gemtek-trailer
|
|
|
|
|
printf "%s%08X" ".GEMTEK." "$$(cksum $@ | cut -d ' ' -f1)" >> $@
|
|
|
|
|
endef
|
|
|
|
|
|
2022-03-20 15:42:37 +00:00
|
|
|
define Build/h3c-blank-header
|
|
|
|
|
dd if=/dev/zero of=$@.blank bs=160 count=1
|
|
|
|
|
cat $@ >> $@.blank
|
|
|
|
|
mv $@.blank $@
|
|
|
|
|
endef
|
|
|
|
|
|
2022-09-15 17:10:52 +00:00
|
|
|
define Build/haier-sim_wr1800k-factory
|
2022-12-12 11:25:45 +00:00
|
|
|
mkdir -p "$@.tmp"
|
|
|
|
|
mv "$@" "$@.tmp/UploadBrush-bin.img"
|
|
|
|
|
$(MKHASH) md5 "$@.tmp/UploadBrush-bin.img" | head -c32 > "$@.tmp/check_MD5.txt"
|
|
|
|
|
$(TAR) -czf "$@.tmp.tgz" -C "$@.tmp" UploadBrush-bin.img check_MD5.txt
|
|
|
|
|
$(STAGING_DIR_HOST)/bin/openssl aes-256-cbc -e -salt -in "$@.tmp.tgz" -out "$@" -k QiLunSmartWL
|
|
|
|
|
printf %32s $(DEVICE_MODEL) >> "$@"
|
|
|
|
|
rm -rf "$@.tmp" "$@.tmp.tgz"
|
2022-09-15 17:10:52 +00:00
|
|
|
endef
|
|
|
|
|
|
2019-04-09 05:48:31 +00:00
|
|
|
define Build/iodata-mstc-header
|
2020-05-08 16:21:06 +00:00
|
|
|
( \
|
|
|
|
|
data_size_crc="$$(dd if=$@ ibs=64 skip=1 2>/dev/null | gzip -c | \
|
|
|
|
|
tail -c 8 | od -An -tx8 --endian little | tr -d ' \n')"; \
|
|
|
|
|
echo -ne "$$(echo $$data_size_crc | sed 's/../\\x&/g')" | \
|
|
|
|
|
dd of=$@ bs=8 count=1 seek=7 conv=notrunc 2>/dev/null; \
|
|
|
|
|
)
|
|
|
|
|
dd if=/dev/zero of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null
|
|
|
|
|
( \
|
|
|
|
|
header_crc="$$(dd if=$@ bs=64 count=1 2>/dev/null | gzip -c | \
|
|
|
|
|
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
|
|
|
|
|
echo -ne "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
|
|
|
|
|
dd of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null; \
|
|
|
|
|
)
|
2019-04-09 05:48:31 +00:00
|
|
|
endef
|
|
|
|
|
|
ramips: mt7621: add support for ZyXEL WSM20
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.
Specifications
==============
SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)
MAC address assignment
======================
The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.
The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.
Installation (web interface)
============================
The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.
The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.
1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy
NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.
Installation (UART method)
==========================
The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:
1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation
Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:
nand read 1800000 53c0000 800
mw.b 1800004 1 1
nand erase 53c0000 800
nand write 1800000 53c0000 800
This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.
Back to stock
=============
It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.
It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:
mtd write zyxel.bin Kernel2
echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
2023-04-04 17:41:26 +00:00
|
|
|
define Build/znet-header
|
|
|
|
|
$(eval version=$(word 1,$(1)))
|
|
|
|
|
( \
|
|
|
|
|
data_size_crc="$$(dd if=$@ 2>/dev/null | gzip -c | \
|
|
|
|
|
tail -c 8 | od -An -N4 -tx4 --endian big | tr -d ' \n')"; \
|
|
|
|
|
payload_len="$$(dd if=$@ bs=4 count=1 skip=1 2>/dev/null | od -An -tdI --endian big | tr -d ' \n')"; \
|
|
|
|
|
payload_size_crc="$$(dd if=$@ ibs=1 count=$$payload_len 2>/dev/null | gzip -c | \
|
|
|
|
|
tail -c 8 | od -An -N4 -tx4 --endian big | tr -d ' \n')"; \
|
|
|
|
|
echo -ne "\x5A\x4E\x45\x54" | dd bs=4 count=1 conv=sync 2>/dev/null; \
|
|
|
|
|
echo -ne "$$(printf '%08x' $$(stat -c%s $@) | fold -s2 | xargs -I {} echo \\x{} | tac | tr -d '\n')" | \
|
|
|
|
|
dd bs=4 count=1 conv=sync 2>/dev/null; \
|
|
|
|
|
echo -ne "$$(echo $$data_size_crc | sed 's/../\\x&/g')" | \
|
|
|
|
|
dd bs=4 count=1 conv=sync 2>/dev/null; \
|
|
|
|
|
echo -ne "$$(echo $$payload_size_crc | sed 's/../\\x&/g')" | \
|
|
|
|
|
dd bs=4 count=1 conv=sync 2>/dev/null; \
|
|
|
|
|
echo -ne "\x12\x34\x56\x78" | dd bs=4 count=1 conv=sync 2>/dev/null; \
|
|
|
|
|
echo -ne "$(version)" | dd bs=28 count=1 conv=sync 2>/dev/null; \
|
|
|
|
|
dd if=/dev/zero bs=262096 count=1 conv=sync 2>/dev/null | tr "\000" "\377"; \
|
|
|
|
|
cat $@; \
|
|
|
|
|
) > $@.new
|
|
|
|
|
mv $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
2021-03-22 21:06:14 +00:00
|
|
|
define Build/belkin-header
|
|
|
|
|
$(eval magic=$(word 1,$(1)))
|
|
|
|
|
$(eval hw_ver=$(word 2,$(1)))
|
|
|
|
|
$(eval fw_ver=$(word 3,$(1)))
|
|
|
|
|
|
|
|
|
|
( \
|
|
|
|
|
type_fw_date=$$(printf "01%02x%02x%02x" \
|
2023-09-15 04:54:30 +00:00
|
|
|
$$(date -d "@$(SOURCE_DATE_EPOCH)" "+%-y %-m %-d")); \
|
2021-03-22 21:06:14 +00:00
|
|
|
hw_fw_ver=$$(printf "%02x%02x%02x%02x" \
|
|
|
|
|
$(hw_ver) $$(echo $(fw_ver) | cut -d. -f-3 | tr . ' ')); \
|
|
|
|
|
fw_len_crc=$$(gzip -c $@ | tail -c 8 | od -An -tx8 | tr -d ' \n'); \
|
|
|
|
|
fw_crc_len="$${fw_len_crc:8:8}$${fw_len_crc:0:8}"; \
|
|
|
|
|
\
|
|
|
|
|
printf "$(magic)" | dd bs=4 count=1 conv=sync 2>/dev/null; \
|
|
|
|
|
printf "$$(echo $${type_fw_date}$${hw_fw_ver} | \
|
|
|
|
|
sed 's/../\\x&/g')"; \
|
|
|
|
|
printf "$$(echo $${fw_crc_len}$${fw_crc_len} | \
|
|
|
|
|
sed 's/../\\x&/g')"; \
|
|
|
|
|
printf "\x5c\x78\x00\x00"; \
|
|
|
|
|
cat $@; \
|
|
|
|
|
) > $@.new
|
|
|
|
|
mv $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
2016-04-09 10:24:29 +00:00
|
|
|
define Build/ubnt-erx-factory-image
|
2016-07-06 08:11:29 +00:00
|
|
|
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
|
mt7621: Make ER-X-SFP factory image compatible with EP-R6
The version inside the compat file determines, if a firmware supports
a specific device. I have not yet fully understood, how this is checked,
but it only seems to indicate which devices are supported by a specific
version of the combined vendor firmware. Devices assume that subsequent
versions, starting with the version that initially added support for a
specific device, are always compatible.
The first compat version that added support for the EP-R6 was '21001:7',
but OpenWrt did use '21001:6' before. This is why the factory image could
not be flashed using the vendor software, but only using TFTP.
The compat version has been bumped by the vendor a few times, but more
devices have been added since (e.g. ER-10X). Because OpenWrt currently
only supports the ER-X, ER-X-SFP and EP-R6, the compat version is
incremented to the version that first supported the EP-R6, which is
'21001:7'.
This allows the factory image to be flashed on EP-R6 without TFTP.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
2020-05-16 10:23:52 +00:00
|
|
|
echo '21001:7' > $(1).compat; \
|
2016-04-09 10:24:29 +00:00
|
|
|
$(TAR) -cf $(1) --transform='s/^.*/compat/' $(1).compat; \
|
|
|
|
|
\
|
|
|
|
|
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp/' $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE); \
|
2021-05-09 20:28:15 +00:00
|
|
|
$(MKHASH) md5 $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) > $(1).md5; \
|
2016-04-09 10:24:29 +00:00
|
|
|
$(TAR) -rf $(1) --transform='s/^.*/vmlinux.tmp.md5/' $(1).md5; \
|
|
|
|
|
\
|
|
|
|
|
echo "dummy" > $(1).rootfs; \
|
|
|
|
|
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp/' $(1).rootfs; \
|
2016-04-01 07:11:48 +00:00
|
|
|
\
|
2021-05-09 20:28:15 +00:00
|
|
|
$(MKHASH) md5 $(1).rootfs > $(1).md5; \
|
2016-04-09 10:24:29 +00:00
|
|
|
$(TAR) -rf $(1) --transform='s/^.*/squashfs.tmp.md5/' $(1).md5; \
|
|
|
|
|
\
|
|
|
|
|
echo '$(BOARD) $(VERSION_CODE) $(VERSION_NUMBER)' > $(1).version; \
|
|
|
|
|
$(TAR) -rf $(1) --transform='s/^.*/version.tmp/' $(1).version; \
|
|
|
|
|
\
|
|
|
|
|
$(CP) $(1) $(BIN_DIR)/; \
|
2016-07-06 08:11:29 +00:00
|
|
|
else \
|
2021-07-20 23:30:41 +00:00
|
|
|
echo "WARNING: initramfs kernel image too big, cannot generate factory image (actual $$(stat -c%s $@); max $(KERNEL_SIZE))" >&2; \
|
2016-04-01 07:11:48 +00:00
|
|
|
fi
|
|
|
|
|
endef
|
|
|
|
|
|
ramips: mt7621: Add support for ZyXEL NR7101
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E
- Switch: 1 LAN port (Gigabiti)
- 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
- SIM: 2 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/yellow under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable. Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.
A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.
MAC addresses:
OpenWrt OEM Address Found as
lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label
wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex)
wwan0 usb0 random
WARNING!!
ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled. Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.
Installation from OEM web GUI:
- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Installation from OEM ssh:
- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
nvram setro uboot DebugFlag 0x1
nvram setro uboot CheckBypass 0
nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Copying OpenWrt to the recovery partition:
- Verify that you are running a working OpenWrt recovery image
from flash
- ssh to root@192.168.1.1 and run:
fw_setenv CheckBypass 0
mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2
NOTE: This should only be done after successfully booting the OpenWrt
recovery image from the primary partition during installation. Do
not do this after having sysupgraded OpenWrt! Reinstalling the
recovery image on normal upgrades is not required or recommended.
Installation from Z-Loader:
- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image
NOTE: ATNR will write the recovery image to both primary and recovery
partitions in one go.
Booting from RAM:
- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
header
This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies! Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.
NOTE: U-Boot configuration is incomplete (on some devices?). You may
have to configure a working mac address before running tftp using
"setenv eth0addr <mac>"
Unlocking the bootloader:
If you are unebale to halt boot, then the bootloader is locked.
The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0. Setting it to 1 is therefore only temporary
when OEM firmware is installed.
- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt
NOTE:
OpenWrt does this automatically on first boot if necessary
NOTE2:
Setting the flag to 0x1 avoids the reset to 0 in known OEM
versions, but this might change.
WARNING:
Writing anything to flash while the bootloader is locked is
considered extremely risky. Errors might cause a permanent
brick!
Enabling management access from LAN:
Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:
- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"
Notes on the OEM/bootloader dual partition scheme
The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.
Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.
The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.
If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.
If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.
If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally. CheckBypass is set to 1 after each successful
validation of Image1.
Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger. But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.
The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.
Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.
Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-04-19 11:00:56 +00:00
|
|
|
define Build/zytrx-header
|
|
|
|
|
$(eval board=$(word 1,$(1)))
|
|
|
|
|
$(eval version=$(word 2,$(1)))
|
|
|
|
|
$(STAGING_DIR_HOST)/bin/zytrx -B '$(board)' -v '$(version)' -i $@ -o $@.new
|
|
|
|
|
mv $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
2022-05-27 15:48:06 +00:00
|
|
|
define Build/zyxel-nwa-fit
|
|
|
|
|
$(TOPDIR)/scripts/mkits-zyxel-fit.sh \
|
|
|
|
|
$@.its $@ "6b e1 6f e1 ff ff ff ff ff ff"
|
|
|
|
|
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
|
|
|
|
|
@mv $@.new $@
|
|
|
|
|
endef
|
|
|
|
|
|
2020-07-14 14:42:40 +00:00
|
|
|
define Device/dsa-migration
|
|
|
|
|
DEVICE_COMPAT_VERSION := 1.1
|
2020-08-08 19:30:44 +00:00
|
|
|
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
|
2020-07-14 14:42:40 +00:00
|
|
|
endef
|
|
|
|
|
|
2023-05-13 13:01:00 +00:00
|
|
|
define Device/nand
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
UBINIZE_OPTS := -E 5
|
|
|
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
|
|
|
endef
|
|
|
|
|
|
2020-07-08 19:18:12 +00:00
|
|
|
define Device/adslr_g7
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-07-08 19:18:12 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := ADSLR
|
|
|
|
|
DEVICE_MODEL := G7
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2020-07-08 19:18:12 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += adslr_g7
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/afoundry_ew1200
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2023-03-19 09:34:07 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := AFOUNDRY
|
|
|
|
|
DEVICE_MODEL := EW1200
|
2020-03-05 13:57:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-mt7603 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += ew1200
|
2016-04-01 07:11:48 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += afoundry_ew1200
|
|
|
|
|
|
ramips: add support for ALFA Network AX1800RM
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621A (880 MHz)
- DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash: 16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: 6x green, 1x green/red
- Buttons: 2x (reset, WPS)
- Antenna: 4x external, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, J4, not populated)
- Power: 12 V DC/1 A (DC jack)
MAC addresses:
LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa)
Flash instructions for web-based U-Boot recovery:
1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.
The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:
1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
in forced mode, without preserving settings: 'sysupgrade -n -F ...'.
Other notes:
If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit f1aaa267f0ea18ffe5840f3ce46a48be123d2f62)
2023-07-28 09:41:14 +00:00
|
|
|
define Device/alfa-network_ax1800rm
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 15488k
|
|
|
|
|
DEVICE_VENDOR := ALFA Network
|
|
|
|
|
DEVICE_MODEL := AX1800RM
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
|
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
IMAGES += recovery.bin
|
|
|
|
|
IMAGE/recovery.bin := append-kernel | append-rootfs | pad-rootfs | check-size
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += alfa-network_ax1800rm
|
|
|
|
|
|
ramips: add support for ALFA Network Quad-E4G
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-03 11:12:44 +00:00
|
|
|
define Device/alfa-network_quad-e4g
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
ramips: add support for ALFA Network Quad-E4G
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-03 11:12:44 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := ALFA Network
|
|
|
|
|
DEVICE_MODEL := Quad-E4G
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 \
|
2022-12-28 04:44:11 +00:00
|
|
|
-wpad-basic-mbedtls
|
2021-05-16 21:48:04 +00:00
|
|
|
SUPPORTED_DEVICES += quad-e4g
|
ramips: add support for ALFA Network Quad-E4G
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-03 11:12:44 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += alfa-network_quad-e4g
|
|
|
|
|
|
ramips: add support for Amped Wireless ALLY router and extender
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips. The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.
Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART: through-hole on PCB.
J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
pin3=GND, pin4=TX. Settings: 57600/8N1.
Note regarding dual system partitions
-------------------------------------
The vendor firmware and boot loader use a dual partition scheme. The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.
OpenWrt does not support this scheme and will always use the first OS
partition. It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.
Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used. We first flash an initramfs image, then
follow with a regular sysupgrade.
Installation:
Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
(Alternatively, you can use the TFTP recovery method below.)
You can use WiFi or Ethernet.
The direct URL is: http://192.168.3.1/07_06_00_firmware.html
a. No login is needed, and you'll be in their setup wizard.
b. You might get a warning about not being connected to the Internet.
c. Towards the bottom of the page will be a section entitled "Or
Manually Upgrade Firmware from a File:" where you can manually choose
and upload a firmware file.
d: Click "Choose File", select the OpenWRT "initramfs" image and click
"Upload."
2) The Router will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image. Note:
you may use the sysupgrade command line tool in lieu of the UI if
you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
of OpenWRT. Start by configuring a computer as a TFTP client:
a. Install a TFTP client (server not necessary)
b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
a. Do this by pressing and holding the reset button on the bottom while
connecting the power.
b. As soon as the LED lights up green (roughly 2-3 seconds), release
the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image. Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Backup the OEM Firmware:
-----------------------
There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.
The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem"). We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.
1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
2) Under "Save mtdblock contents," first select "firmware" and click
"Save mtdblock" to download the image.
3) Repeat the process, but select "oem" from the pull-down menu.
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow the TFTP recovery steps for the Extender, and use the
backup image.
* OpenWrt "Flash Firmware" interface:
Upload the backup image and select "Force update"
before continuing.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
2021-06-05 12:17:42 +00:00
|
|
|
define Device/ampedwireless_ally_common
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: add support for Amped Wireless ALLY router and extender
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips. The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.
Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART: through-hole on PCB.
J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
pin3=GND, pin4=TX. Settings: 57600/8N1.
Note regarding dual system partitions
-------------------------------------
The vendor firmware and boot loader use a dual partition scheme. The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.
OpenWrt does not support this scheme and will always use the first OS
partition. It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.
Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used. We first flash an initramfs image, then
follow with a regular sysupgrade.
Installation:
Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
(Alternatively, you can use the TFTP recovery method below.)
You can use WiFi or Ethernet.
The direct URL is: http://192.168.3.1/07_06_00_firmware.html
a. No login is needed, and you'll be in their setup wizard.
b. You might get a warning about not being connected to the Internet.
c. Towards the bottom of the page will be a section entitled "Or
Manually Upgrade Firmware from a File:" where you can manually choose
and upload a firmware file.
d: Click "Choose File", select the OpenWRT "initramfs" image and click
"Upload."
2) The Router will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image. Note:
you may use the sysupgrade command line tool in lieu of the UI if
you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
of OpenWRT. Start by configuring a computer as a TFTP client:
a. Install a TFTP client (server not necessary)
b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
a. Do this by pressing and holding the reset button on the bottom while
connecting the power.
b. As soon as the LED lights up green (roughly 2-3 seconds), release
the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image. Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Backup the OEM Firmware:
-----------------------
There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.
The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem"). We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.
1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
2) Under "Save mtdblock contents," first select "firmware" and click
"Save mtdblock" to download the image.
3) Repeat the process, but select "oem" from the pull-down menu.
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow the TFTP recovery steps for the Extender, and use the
backup image.
* OpenWrt "Flash Firmware" interface:
Upload the backup image and select "Force update"
before continuing.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
2021-06-05 12:17:42 +00:00
|
|
|
DEVICE_VENDOR := Amped Wireless
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware
|
ramips: add support for Amped Wireless ALLY router and extender
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips. The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.
Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART: through-hole on PCB.
J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
pin3=GND, pin4=TX. Settings: 57600/8N1.
Note regarding dual system partitions
-------------------------------------
The vendor firmware and boot loader use a dual partition scheme. The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.
OpenWrt does not support this scheme and will always use the first OS
partition. It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.
Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used. We first flash an initramfs image, then
follow with a regular sysupgrade.
Installation:
Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
(Alternatively, you can use the TFTP recovery method below.)
You can use WiFi or Ethernet.
The direct URL is: http://192.168.3.1/07_06_00_firmware.html
a. No login is needed, and you'll be in their setup wizard.
b. You might get a warning about not being connected to the Internet.
c. Towards the bottom of the page will be a section entitled "Or
Manually Upgrade Firmware from a File:" where you can manually choose
and upload a firmware file.
d: Click "Choose File", select the OpenWRT "initramfs" image and click
"Upload."
2) The Router will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image. Note:
you may use the sysupgrade command line tool in lieu of the UI if
you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
of OpenWRT. Start by configuring a computer as a TFTP client:
a. Install a TFTP client (server not necessary)
b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
a. Do this by pressing and holding the reset button on the bottom while
connecting the power.
b. As soon as the LED lights up green (roughly 2-3 seconds), release
the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image. Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Backup the OEM Firmware:
-----------------------
There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.
The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem"). We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.
1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
2) Under "Save mtdblock contents," first select "firmware" and click
"Save mtdblock" to download the image.
3) Repeat the process, but select "oem" from the pull-down menu.
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow the TFTP recovery steps for the Extender, and use the
backup image.
* OpenWrt "Flash Firmware" interface:
Upload the backup image and select "Force update"
before continuing.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
2021-06-05 12:17:42 +00:00
|
|
|
IMAGE_SIZE := 32768k
|
|
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'flashable-initramfs' |\
|
|
|
|
|
edimax-header -s CSYS -m RN68 -f 0x001c0000 -S 0x01100000
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/ampedwireless_ally-r1900k
|
|
|
|
|
$(Device/ampedwireless_ally_common)
|
|
|
|
|
DEVICE_MODEL := ALLY-R1900K
|
|
|
|
|
DEVICE_PACKAGES += kmod-usb3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += ampedwireless_ally-r1900k
|
|
|
|
|
|
|
|
|
|
define Device/ampedwireless_ally-00x19k
|
|
|
|
|
$(Device/ampedwireless_ally_common)
|
|
|
|
|
DEVICE_MODEL := ALLY-00X19K
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += ampedwireless_ally-00x19k
|
|
|
|
|
|
ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.
Specifications
--------------
SOC : Mediatek MT7621AT
ETH : Two 1 gigabit ports, built into the SOC
WIFI : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED : Power (green+red)
LED : WiFi (green+blue)
LED : WPS (green+red)
LED : Followme (green+red)
Power : 12 VDC, 1A barrel plug
Winbond variant:
RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1
Macronix variant:
RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1
Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.
The pinout is: VCC (the square), RX, TX, GND.
Installation
------------
See the Wiki page [1] for more details, it comes down to:
1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
environment located at 0x30000
Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.
MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use | address | example |
+----------+------------------+-------------------+
| Device | label | 00:00:00:11:00:00 |
| Ethernet | + 3 | 00:00:00:11:00:03 |
| 2g | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g | + 1 | 00:00:00:11:00:01 |
+----------+------------------+-------------------+
The label address is stored in ASCII in the board_data partition
Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
both partitions for more storage space.
Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
macaddr_add
- Only the power LED is configured by default
References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
2023-01-08 16:03:25 +00:00
|
|
|
define Device/arcadyan_we420223-99
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := Arcadyan
|
|
|
|
|
DEVICE_MODEL := WE420223-99
|
|
|
|
|
DEVICE_ALT0_VENDOR := KPN
|
|
|
|
|
DEVICE_ALT0_MODEL := Experia WiFi
|
|
|
|
|
IMAGE_SIZE := 32128k
|
|
|
|
|
KERNEL_SIZE := 4352k
|
|
|
|
|
UBINIZE_OPTS := -E 5
|
|
|
|
|
PAGESIZE := 1
|
|
|
|
|
SUBPAGESIZE := 1
|
|
|
|
|
VID_HDR_OFFSET := 64
|
|
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
|
|
|
uImage none | arcadyan-trx 0x746f435d
|
|
|
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
|
|
|
uImage none
|
|
|
|
|
IMAGES += factory.trx
|
|
|
|
|
IMAGE/factory.trx := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | check-size
|
|
|
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.
Specifications
--------------
SOC : Mediatek MT7621AT
ETH : Two 1 gigabit ports, built into the SOC
WIFI : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED : Power (green+red)
LED : WiFi (green+blue)
LED : WPS (green+red)
LED : Followme (green+red)
Power : 12 VDC, 1A barrel plug
Winbond variant:
RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1
Macronix variant:
RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1
Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.
The pinout is: VCC (the square), RX, TX, GND.
Installation
------------
See the Wiki page [1] for more details, it comes down to:
1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
environment located at 0x30000
Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.
MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use | address | example |
+----------+------------------+-------------------+
| Device | label | 00:00:00:11:00:00 |
| Ethernet | + 3 | 00:00:00:11:00:03 |
| 2g | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g | + 1 | 00:00:00:11:00:01 |
+----------+------------------+-------------------+
The label address is stored in ASCII in the board_data partition
Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
both partitions for more storage space.
Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
macaddr_add
- Only the power LED is configured by default
References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
2023-01-08 16:03:25 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += arcadyan_we420223-99
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/asiarf_ap7621-001
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2023-06-02 17:36:28 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-15 12:55:24 +00:00
|
|
|
IMAGE_SIZE := 16000k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := AsiaRF
|
|
|
|
|
DEVICE_MODEL := AP7621-001
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
|
|
|
|
-wpad-basic-mbedtls -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asiarf_ap7621-001
|
|
|
|
|
|
2019-07-22 10:54:06 +00:00
|
|
|
define Device/asiarf_ap7621-nv1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2023-06-02 17:36:28 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 10:54:06 +00:00
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
DEVICE_VENDOR := AsiaRF
|
|
|
|
|
DEVICE_MODEL := AP7621-NV1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
|
|
|
|
-wpad-basic-mbedtls -uboot-envtools
|
2019-07-22 10:54:06 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asiarf_ap7621-nv1
|
|
|
|
|
|
2022-07-27 15:50:40 +00:00
|
|
|
define Device/asus_rp-ac56
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RP-AC56
|
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-i2c-ralink kmod-sound-mt7620 -uboot-envtools
|
2022-07-27 15:50:40 +00:00
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | check-size
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
|
|
|
check-size | append-metadata
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_rp-ac56
|
|
|
|
|
|
2022-06-20 09:02:15 +00:00
|
|
|
define Device/asus_rp-ac87
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RP-AC87
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | check-size
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
|
|
|
check-size | append-metadata
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware rssileds -uboot-envtools
|
2022-06-20 09:02:15 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_rp-ac87
|
|
|
|
|
|
2023-04-30 20:36:09 +00:00
|
|
|
define Device/asus_rt-ac57u-v1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-11 15:15:48 +00:00
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RT-AC57U
|
2023-04-30 20:36:09 +00:00
|
|
|
DEVICE_VARIANT := v1
|
2021-12-24 06:25:01 +00:00
|
|
|
DEVICE_ALT0_VENDOR := ASUS
|
|
|
|
|
DEVICE_ALT0_MODEL := RT-AC1200GU
|
2019-07-11 15:15:48 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2020-08-07 09:56:43 +00:00
|
|
|
kmod-usb-ledtrig-usbport
|
2023-04-30 20:36:09 +00:00
|
|
|
SUPPORTED_DEVICES += asus,rt-ac57u
|
2019-07-11 15:15:48 +00:00
|
|
|
endef
|
2023-04-30 20:36:09 +00:00
|
|
|
TARGET_DEVICES += asus_rt-ac57u-v1
|
2019-07-11 15:15:48 +00:00
|
|
|
|
2019-10-22 19:44:09 +00:00
|
|
|
define Device/asus_rt-ac65p
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2019-10-22 19:44:09 +00:00
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RT-AC65P
|
|
|
|
|
IMAGE_SIZE := 51200k
|
|
|
|
|
IMAGES += factory.bin
|
2019-12-19 18:40:33 +00:00
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
2020-03-10 13:58:27 +00:00
|
|
|
check-size
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615-firmware
|
2019-10-22 19:44:09 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_rt-ac65p
|
|
|
|
|
|
2019-09-15 14:20:11 +00:00
|
|
|
define Device/asus_rt-ac85p
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2019-09-15 14:20:11 +00:00
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RT-AC85P
|
|
|
|
|
IMAGE_SIZE := 51200k
|
|
|
|
|
IMAGES += factory.bin
|
2019-12-19 18:40:33 +00:00
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
2020-03-10 13:58:27 +00:00
|
|
|
check-size
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615-firmware
|
2019-09-15 14:20:11 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_rt-ac85p
|
|
|
|
|
|
2020-11-02 11:50:01 +00:00
|
|
|
define Device/asus_rt-n56u-b1
|
|
|
|
|
$(Device/dsa-migration)
|
2022-10-21 17:47:38 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2020-11-02 11:50:01 +00:00
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RT-N56U
|
|
|
|
|
DEVICE_VARIANT := B1
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2020-11-02 11:50:01 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_rt-n56u-b1
|
|
|
|
|
|
ramips: add support for ASUS RT-AX53U
Specifications:
- Device: ASUS RT-AX53U
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 3 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- Ports: USB 3.0
- LEDs: 1x POWER (blue, configurable)
3x LAN (blue, configurable)
1x WAN (blue, configurable)
1x USB (blue, not configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
(replaced led label, added key-* prefix to buttons, added note about
BBT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-14 06:11:52 +00:00
|
|
|
define Device/asus_rt-ax53u
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: add support for ASUS RT-AX53U
Specifications:
- Device: ASUS RT-AX53U
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 3 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- Ports: USB 3.0
- LEDs: 1x POWER (blue, configurable)
3x LAN (blue, configurable)
1x WAN (blue, configurable)
1x USB (blue, not configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
(replaced led label, added key-* prefix to buttons, added note about
BBT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-14 06:11:52 +00:00
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RT-AX53U
|
2023-01-08 00:47:21 +00:00
|
|
|
DEVICE_ALT0_VENDOR := ASUS
|
|
|
|
|
DEVICE_ALT0_MODEL := RT-AX1800U
|
ramips: add support for ASUS RT-AX53U
Specifications:
- Device: ASUS RT-AX53U
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 3 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- Ports: USB 3.0
- LEDs: 1x POWER (blue, configurable)
3x LAN (blue, configurable)
1x WAN (blue, configurable)
1x USB (blue, not configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
(replaced led label, added key-* prefix to buttons, added note about
BBT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-14 06:11:52 +00:00
|
|
|
IMAGE_SIZE := 51200k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
|
|
|
check-size
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware kmod-usb3 kmod-usb-ledtrig-usbport
|
ramips: add support for ASUS RT-AX53U
Specifications:
- Device: ASUS RT-AX53U
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 3 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- Ports: USB 3.0
- LEDs: 1x POWER (blue, configurable)
3x LAN (blue, configurable)
1x WAN (blue, configurable)
1x USB (blue, not configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
(replaced led label, added key-* prefix to buttons, added note about
BBT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-14 06:11:52 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_rt-ax53u
|
|
|
|
|
|
2023-01-29 05:37:28 +00:00
|
|
|
define Device/asus_rt-ax54
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2023-01-29 05:37:28 +00:00
|
|
|
DEVICE_VENDOR := ASUS
|
|
|
|
|
DEVICE_MODEL := RT-AX54
|
|
|
|
|
DEVICE_ALT0_VENDOR := ASUS
|
2023-02-16 10:36:25 +00:00
|
|
|
DEVICE_ALT0_MODEL := RT-AX54HP
|
2023-01-29 05:37:28 +00:00
|
|
|
DEVICE_ALT1_VENDOR := ASUS
|
2023-02-16 10:36:25 +00:00
|
|
|
DEVICE_ALT1_MODEL := RT-AX1800HP
|
2023-01-29 05:37:28 +00:00
|
|
|
DEVICE_ALT2_VENDOR := ASUS
|
2023-02-16 10:36:25 +00:00
|
|
|
DEVICE_ALT2_MODEL := RT-AX1800S
|
2023-01-29 05:37:28 +00:00
|
|
|
IMAGE_SIZE := 51200k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
|
|
|
check-size
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
2023-01-29 05:37:28 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_rt-ax54
|
|
|
|
|
|
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-01-05 13:11:56 +00:00
|
|
|
define Device/beeline_smartbox-flash
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-01-05 13:11:56 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := Beeline
|
|
|
|
|
DEVICE_MODEL := SmartBox Flash
|
|
|
|
|
IMAGE_SIZE := 32768k
|
|
|
|
|
KERNEL_SIZE := 4352k
|
|
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
2022-04-28 18:24:07 +00:00
|
|
|
uImage none | arcadyan-trx 0x746f435d | pad-to $$(KERNEL_SIZE)
|
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-01-05 13:11:56 +00:00
|
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
|
|
|
uImage none
|
|
|
|
|
IMAGES += factory.trx
|
|
|
|
|
IMAGE/factory.trx := append-kernel | append-ubi | check-size
|
2023-02-17 11:12:40 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615-firmware uencrypt-mbedtls
|
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-01-05 13:11:56 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += beeline_smartbox-flash
|
|
|
|
|
|
ramips: add support for Beeline SmartBox GIGA
Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Nanya NT5CC128M16JR-EK
Flash: 128 MiB, Macronix MX30LF1G18AC
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7613BE): a/n/ac, 2x2
Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2)
USB ports: 1xUSB3.0
Button: 1 button (Reset/WPS)
PCB ID: DBE00B-1.6MM
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Downgrade stock (Beeline) firmware to v.1.0.02;
2. Give factory OpenWrt image a shorter name, e.g. 1001.img;
3. Upload and update the firmware via the original web interface.
Remark: You might need make the 3rd step twice if your running firmware
is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware
reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update.
Revert to stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:16 |
| WAN | label + 1 | *:17 |
| 2g | label + 4 | *:1a |
| 5g | label + 5 | *:1b |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Notes
-----
1. The following scripts are required for the build:
sercomm-crypto.py - already exists in OpenWrt
sercomm-partition-tag.py - already exists in OpenWrt
sercomm-payload.py - already exists in OpenWrt
sercomm-pid.py - new, the part of this pull request
sercomm-kernel-header.py - new, the part of this pull request
2. This device (same as other Sercomm S2,S3-based devices) requires
special LZMA and LOADADDR settings for successful boot:
LZMA_TEXT_START=0x82800000
KERNEL_LOADADDR=0x81001000
LOADADDR=0x80001000
3. This device (same as several other Sercomm-based devices - Beeline,
Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing
real partition offsets, which may differ from device to device
depending on the number and location of bad blocks on NAND.
"fixed-partitions" is used if the partition map is not found or
corrupted. This behavour (it's the same as on stock firmware) is
provided by MTD_SERCOMM_PARTS module.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
|
|
|
define Device/beeline_smartbox-giga
|
|
|
|
|
$(Device/sercomm_dxx)
|
|
|
|
|
IMAGE_SIZE := 24576k
|
|
|
|
|
SERCOMM_HWID := DBE
|
|
|
|
|
SERCOMM_HWVER := 10100
|
|
|
|
|
SERCOMM_SWVER := 1001
|
|
|
|
|
DEVICE_VENDOR := Beeline
|
|
|
|
|
DEVICE_MODEL := SmartBox GIGA
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb3
|
ramips: add support for Beeline SmartBox GIGA
Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Nanya NT5CC128M16JR-EK
Flash: 128 MiB, Macronix MX30LF1G18AC
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7613BE): a/n/ac, 2x2
Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2)
USB ports: 1xUSB3.0
Button: 1 button (Reset/WPS)
PCB ID: DBE00B-1.6MM
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Downgrade stock (Beeline) firmware to v.1.0.02;
2. Give factory OpenWrt image a shorter name, e.g. 1001.img;
3. Upload and update the firmware via the original web interface.
Remark: You might need make the 3rd step twice if your running firmware
is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware
reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update.
Revert to stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:16 |
| WAN | label + 1 | *:17 |
| 2g | label + 4 | *:1a |
| 5g | label + 5 | *:1b |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Notes
-----
1. The following scripts are required for the build:
sercomm-crypto.py - already exists in OpenWrt
sercomm-partition-tag.py - already exists in OpenWrt
sercomm-payload.py - already exists in OpenWrt
sercomm-pid.py - new, the part of this pull request
sercomm-kernel-header.py - new, the part of this pull request
2. This device (same as other Sercomm S2,S3-based devices) requires
special LZMA and LOADADDR settings for successful boot:
LZMA_TEXT_START=0x82800000
KERNEL_LOADADDR=0x81001000
LOADADDR=0x80001000
3. This device (same as several other Sercomm-based devices - Beeline,
Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing
real partition offsets, which may differ from device to device
depending on the number and location of bad blocks on NAND.
"fixed-partitions" is used if the partition map is not found or
corrupted. This behavour (it's the same as on stock firmware) is
provided by MTD_SERCOMM_PARTS module.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += beeline_smartbox-giga
|
|
|
|
|
|
ramips: add support for Sercomm S1500 devices
This commit adds support for following wireless routers:
- Beeline SmartBox PRO (Serсomm S1500 AWI)
- WiFire S1500.NBN (Serсomm S1500 BUC)
This commit is based on this PR:
- Link: https://github.com/openwrt/openwrt/pull/4770
- Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.
My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1
Common specification
--------------------
SoC: MediaTek MT7621AT (880 MHz, 2 cores)
Switch: MediaTek MT7530 (via SoC MT7621AT)
Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe: via J2 on PCB, not soldered on the board
UART: J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek
Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1
WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1
MAC address table (PRO)
-----------------------
use address source
LAN *:23 factory 0x1000 (label)
WAN *:24 factory $label +1
2g *:23 factory $label
5g *:25 factory $label +2
MAC addresses (NBN)
-------------------
use address source
LAN *:0e factory 0x1000
WAN *:0f LAN +1 (label)
2g *:0f LAN +1
5g *:10 LAN +2
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
a. OpenWrt - that's OK, the mission accomplished
b. Stock firmware - install Stock firmware (to switch booflag from
Sercomm0 to Sercomm1) and then OpenWrt factory image.
Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
reboot
2. Install stock firmware via the web OEM firmware interface
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 2d6784a033a994043759fa3b94c48afd5df81f88)
2023-06-11 20:50:23 +00:00
|
|
|
define Device/beeline_smartbox-pro
|
|
|
|
|
$(Device/sercomm_s1500)
|
|
|
|
|
DEVICE_VENDOR := Beeline
|
|
|
|
|
DEVICE_MODEL := SmartBox PRO
|
|
|
|
|
DEVICE_ALT0_VENDOR := Sercomm
|
|
|
|
|
DEVICE_ALT0_MODEL := S1500 AWI
|
|
|
|
|
IMAGE_SIZE := 34816k
|
|
|
|
|
IMAGE/factory.img := append-kernel | sercomm-kernel-factory | \
|
|
|
|
|
sercomm-reset-slot1-chksum | append-ubi | check-size | \
|
|
|
|
|
sercomm-factory-cqr | sercomm-append-tail | sercomm-mkhash
|
|
|
|
|
SERCOMM_HWID := AWI
|
|
|
|
|
SERCOMM_HWVER := 10000
|
|
|
|
|
SERCOMM_ROOTFS2_OFFSET := 0x3d00000
|
|
|
|
|
SERCOMM_SWVER := 2020
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += beeline_smartbox-pro
|
|
|
|
|
|
ramips: add support for Beeline SmartBox TURBO
Beeline SmartBox TURBO is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 2 buttons (Reset & WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (admin:admin)
2. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
3. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
4. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
5. Connect to the router using SSH shell (SuperUser:SNxxxxxxxxxx, where
SNxxxxxxxxxx is the serial number from the backplate label)
6. Run in SSH shell:
sh
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface (admin:admin)
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
1. Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:54 |
| WAN | label + 1 | *:55 |
| 2g | label + 4 | *:58 |
| 5g | label + 5 | *:59 |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Co-developed-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
|
|
|
define Device/beeline_smartbox-turbo
|
|
|
|
|
$(Device/sercomm_dxx)
|
|
|
|
|
IMAGE_SIZE := 32768k
|
|
|
|
|
SERCOMM_HWID := DF3
|
|
|
|
|
SERCOMM_HWVER := 10200
|
|
|
|
|
SERCOMM_SWVER := 1004
|
|
|
|
|
DEVICE_VENDOR := Beeline
|
|
|
|
|
DEVICE_MODEL := SmartBox TURBO
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware kmod-usb3
|
ramips: add support for Beeline SmartBox TURBO
Beeline SmartBox TURBO is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 2 buttons (Reset & WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (admin:admin)
2. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
3. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
4. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
5. Connect to the router using SSH shell (SuperUser:SNxxxxxxxxxx, where
SNxxxxxxxxxx is the serial number from the backplate label)
6. Run in SSH shell:
sh
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface (admin:admin)
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
1. Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:54 |
| WAN | label + 1 | *:55 |
| 2g | label + 4 | *:58 |
| 5g | label + 5 | *:59 |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Co-developed-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += beeline_smartbox-turbo
|
|
|
|
|
|
ramips: Add support for Beeline SmartBox TURBO+
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
(cherry picked from commit 8fcfb21b16e7537b9a871a1f67cb218c6be93149)
2022-12-07 16:44:09 +00:00
|
|
|
define Device/beeline_smartbox-turbo-plus
|
|
|
|
|
$(Device/sercomm_cxx)
|
|
|
|
|
IMAGE_SIZE := 32768k
|
|
|
|
|
SERCOMM_HWID := CQR
|
|
|
|
|
SERCOMM_HWVER := 10000
|
|
|
|
|
SERCOMM_SWVER := 2010
|
|
|
|
|
DEVICE_VENDOR := Beeline
|
|
|
|
|
DEVICE_MODEL := SmartBox TURBO+
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware kmod-usb3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += beeline_smartbox-turbo-plus
|
|
|
|
|
|
2021-03-22 21:06:14 +00:00
|
|
|
define Device/belkin_rt1800
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2021-03-22 21:06:14 +00:00
|
|
|
IMAGE_SIZE := 49152k
|
|
|
|
|
DEVICE_VENDOR := Belkin
|
|
|
|
|
DEVICE_MODEL := RT1800
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware kmod-usb3
|
2021-03-22 21:06:14 +00:00
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
|
|
|
|
append-squashfs4-fakeroot
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
|
|
|
append-ubi | check-size | belkin-header RT18 1 9.9.9
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += belkin_rt1800
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/buffalo_wsr-1166dhp
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-24 05:51:53 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-07 14:27:51 +00:00
|
|
|
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
|
2019-07-15 12:55:24 +00:00
|
|
|
IMAGE_SIZE := 15936k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := Buffalo
|
|
|
|
|
DEVICE_MODEL := WSR-1166DHP
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += wsr-1166
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += buffalo_wsr-1166dhp
|
|
|
|
|
|
2019-03-23 13:45:42 +00:00
|
|
|
define Device/buffalo_wsr-2533dhpl
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-24 05:51:53 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-03-23 13:45:42 +00:00
|
|
|
IMAGE_SIZE := 7936k
|
|
|
|
|
DEVICE_VENDOR := Buffalo
|
|
|
|
|
DEVICE_MODEL := WSR-2533DHPL
|
2020-05-23 22:33:48 +00:00
|
|
|
DEVICE_ALT0_VENDOR := Buffalo
|
|
|
|
|
DEVICE_ALT0_MODEL := WSR-2533DHP
|
2019-03-23 13:45:42 +00:00
|
|
|
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2019-03-23 13:45:42 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += buffalo_wsr-2533dhpl
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/buffalo_wsr-600dhp
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2023-04-05 18:42:15 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := Buffalo
|
|
|
|
|
DEVICE_MODEL := WSR-600DHP
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-rt2800-pci -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += wsr-600
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += buffalo_wsr-600dhp
|
2016-04-01 07:11:48 +00:00
|
|
|
|
2022-03-14 09:26:23 +00:00
|
|
|
define Device/bolt_arion
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 32448k
|
|
|
|
|
DEVICE_VENDOR := BOLT
|
|
|
|
|
DEVICE_MODEL := Arion
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
|
2022-03-14 09:26:23 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += bolt_arion
|
|
|
|
|
|
2023-05-19 00:35:51 +00:00
|
|
|
define Device/comfast_cf-e390ax
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
|
DEVICE_VENDOR := ComFast
|
|
|
|
|
DEVICE_MODEL := CF-E390AX
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
|
|
|
check-size | append-metadata
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | check-size
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += comfast_cf-e390ax
|
|
|
|
|
|
2023-08-18 21:26:59 +00:00
|
|
|
define Device/comfast_cf-ew72-v2
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
|
DEVICE_VENDOR := ComFast
|
|
|
|
|
DEVICE_MODEL := CF-EW72 V2
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
|
|
|
check-size | append-metadata
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | check-size
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += comfast_cf-ew72-v2
|
|
|
|
|
|
2022-11-12 18:31:41 +00:00
|
|
|
define Device/cudy_m1800
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Cudy
|
|
|
|
|
DEVICE_MODEL := M1800
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
UIMAGE_NAME := R17
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
2022-11-12 18:31:41 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += cudy_m1800
|
|
|
|
|
|
2022-09-20 11:24:43 +00:00
|
|
|
define Device/cudy_wr1300-v1
|
ramips: add support for Cudy WR1300
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7612E
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 3.0
- Buttons: Reset, WPS
- LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
- Power: DC 12V 1A tip positive
UART Serial:
115200 baud
Located on unpopulated 4 pin header near J4:
J4
[o] Rx
[o] Tx
[o] GND
[ ] Vcc - Do not connect
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
MAC addresses as verified by OEM firmware:
use address source
LAN *:f0 label
WAN *:f1 label + 1
2g *:f0 label
5g *:f2 label + 2
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2021-01-27 17:35:49 +00:00
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
|
DEVICE_VENDOR := Cudy
|
|
|
|
|
DEVICE_MODEL := WR1300
|
2022-09-20 11:24:43 +00:00
|
|
|
DEVICE_VARIANT := v1
|
ramips: add support for Cudy WR1300
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7612E
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 3.0
- Buttons: Reset, WPS
- LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
- Power: DC 12V 1A tip positive
UART Serial:
115200 baud
Located on unpopulated 4 pin header near J4:
J4
[o] Rx
[o] Tx
[o] GND
[ ] Vcc - Do not connect
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
MAC addresses as verified by OEM firmware:
use address source
LAN *:f0 label
WAN *:f1 label + 1
2g *:f0 label
5g *:f2 label + 2
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2021-01-27 17:35:49 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2022-09-20 11:24:43 +00:00
|
|
|
SUPPORTED_DEVICES += cudy,wr1300 R10
|
ramips: add support for Cudy WR1300
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7612E
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 3.0
- Buttons: Reset, WPS
- LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
- Power: DC 12V 1A tip positive
UART Serial:
115200 baud
Located on unpopulated 4 pin header near J4:
J4
[o] Rx
[o] Tx
[o] GND
[ ] Vcc - Do not connect
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
MAC addresses as verified by OEM firmware:
use address source
LAN *:f0 label
WAN *:f1 label + 1
2g *:f0 label
5g *:f2 label + 2
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2021-01-27 17:35:49 +00:00
|
|
|
endef
|
2022-09-20 11:24:43 +00:00
|
|
|
TARGET_DEVICES += cudy_wr1300-v1
|
|
|
|
|
|
|
|
|
|
define Device/cudy_wr1300-v2
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
|
DEVICE_VENDOR := Cudy
|
|
|
|
|
DEVICE_MODEL := WR1300
|
|
|
|
|
DEVICE_VARIANT := v2
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
2022-09-20 11:24:43 +00:00
|
|
|
SUPPORTED_DEVICES += cudy,wr1300 R23
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += cudy_wr1300-v2
|
ramips: add support for Cudy WR1300
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7612E
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 3.0
- Buttons: Reset, WPS
- LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
- Power: DC 12V 1A tip positive
UART Serial:
115200 baud
Located on unpopulated 4 pin header near J4:
J4
[o] Rx
[o] Tx
[o] GND
[ ] Vcc - Do not connect
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
MAC addresses as verified by OEM firmware:
use address source
LAN *:f0 label
WAN *:f1 label + 1
2g *:f0 label
5g *:f2 label + 2
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2021-01-27 17:35:49 +00:00
|
|
|
|
ramips: Add support for Cudy WR1300 v3
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7613BE
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WPS
- LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS
- Power: DC 12V 1A tip positive
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Cudy WR1300 v3 differs from v2 only in swapped WiFi chip PCIe slots. Common
nodes are extracted to .dtsi and new v2 and v3 dts are created.
Cudy WR1300 v2 dts now contains ieee80211-freq-limit.
The same manufacturer's built OpenWRT image is provided for both v2 and v3
devices as a step in installing, but for proper WiFi functionality,
a separate build is required.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
Backported from branch main to 23.05.
Signed-off-by: Filip Milivojevic <zekica@gmail.com>
(cherry picked from commit 288738c59de0eeca1a0d2042882445ad54d95fe7)
2024-01-18 18:47:47 +00:00
|
|
|
define Device/cudy_wr1300-v3
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
|
DEVICE_VENDOR := Cudy
|
|
|
|
|
DEVICE_MODEL := WR1300
|
|
|
|
|
DEVICE_VARIANT := v3
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
|
|
|
|
SUPPORTED_DEVICES += cudy,wr1300 R30
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += cudy_wr1300-v3
|
|
|
|
|
|
2020-12-24 10:32:47 +00:00
|
|
|
define Device/cudy_wr2100
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Cudy
|
|
|
|
|
DEVICE_MODEL := WR2100
|
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
|
UIMAGE_NAME := R11
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware -uboot-envtools
|
2020-12-24 10:32:47 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += cudy_wr2100
|
|
|
|
|
|
2023-04-21 01:39:38 +00:00
|
|
|
define Device/cudy_x6-v1
|
ramips: add support for Cudy X6
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download
Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-22 14:45:19 +00:00
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 32256k
|
|
|
|
|
DEVICE_VENDOR := Cudy
|
|
|
|
|
DEVICE_MODEL := X6
|
2023-04-21 01:39:38 +00:00
|
|
|
DEVICE_VARIANT := v1
|
ramips: add support for Cudy X6
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download
Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-22 14:45:19 +00:00
|
|
|
UIMAGE_NAME := R13
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
2023-04-21 01:39:38 +00:00
|
|
|
SUPPORTED_DEVICES += cudy,x6 R13
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += cudy_x6-v1
|
|
|
|
|
|
|
|
|
|
define Device/cudy_x6-v2
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
|
DEVICE_VENDOR := Cudy
|
|
|
|
|
DEVICE_MODEL := X6
|
|
|
|
|
DEVICE_VARIANT := v2
|
|
|
|
|
UIMAGE_NAME := R30
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
|
|
|
|
SUPPORTED_DEVICES += cudy,x6 R30
|
ramips: add support for Cudy X6
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download
Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-22 14:45:19 +00:00
|
|
|
endef
|
2023-04-21 01:39:38 +00:00
|
|
|
TARGET_DEVICES += cudy_x6-v2
|
ramips: add support for Cudy X6
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download
Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-09-22 14:45:19 +00:00
|
|
|
|
ramips: add support for D-Link COVR-X1860 A1
The COVR-X1860 are MT7621-based AX1800 devices (similar to DAP-X1860, but
with two Ethernet ports and external power supply) that are sold in sets
of two (COVR-X1862) and three (COVR-X1863).
Specification:
- MT7621
- MT7915 + MT7975 2x2 802.11ax (DBDC)
- 256MB RAM
- 128 MB flash
- 3 LEDs (red, orange, white), routed to one indicator in the top of the device
- 2 buttons (WPS in the back and Reset at the bottom of the device)
MAC addresses:
- LAN MAC (printed on the device) is stored in config2 partition as ASCII (entry factory_mac=xx:xx:xx:xx:xx:xx)
- WAN MAC: LAN MAC + 3
- 2.4G MAC: LAN MAC + 1
- 5G MAC: LAN MAC + 2
The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1
Flashing via OEM Web Interface:
- Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-factory.bin via the OEM web interface firmware update
- The configuration wizard can be skipped by directly going to http://192.168.0.1/UpdateFirmware_Simple.html
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks red
- Open a Chromium based browser and goto http://192.168.0.1
- Download openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks red
- Open a Chromium based browser and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/openwrt/firmware-utils/blob/master/src/dlink-sge-image.c and https://raw.githubusercontent.com/openwrt/firmware-utils/master/src/dlink-sge-image.h
- Compile a binary from the downloaded file, e.g. gcc dlink-sge-image.c -lcrypto -o dlink-sge-image
- Run ./dlink-sge-image COVR-X1860 <OriginalFirmware> <OutputFile> -d
- Example for firmware 102b01: ./dlink-sge-image COVR-X1860 COVR-X1860_RevA_Firmware_102b01.bin COVR-X1860_RevA_Firmware_102b01_Decrypted.bin -d
The pull request is based on the discussion in https://forum.openwrt.org/t/add-support-for-d-link-covr-x1860
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit 0a18259e4aa361cd9e5848c038be4b9f4e3bfcc6)
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
2023-11-03 10:22:02 +00:00
|
|
|
define Device/dlink_covr-x1860-a1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
KERNEL_SIZE := 8192k
|
|
|
|
|
IMAGE_SIZE := 40960k
|
|
|
|
|
DEVICE_VENDOR := D-Link
|
|
|
|
|
DEVICE_MODEL := COVR-X1860
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
|
|
|
UBINIZE_OPTS := -E 5
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
|
|
|
|
append-squashfs4-fakeroot
|
|
|
|
|
IMAGES += factory.bin recovery.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
|
|
|
IMAGE/recovery.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
|
|
|
|
append-ubi | check-size
|
|
|
|
|
IMAGE/factory.bin := $$(IMAGE/recovery.bin) | \
|
|
|
|
|
append-dlink-covr-metadata $$(DEVICE_MODEL) | \
|
|
|
|
|
dlink-sge-image $$(DEVICE_MODEL)
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_covr-x1860-a1
|
|
|
|
|
|
2023-04-09 19:47:58 +00:00
|
|
|
define Device/dlink_dap-1620-b1
|
|
|
|
|
DEVICE_VENDOR := D-Link
|
|
|
|
|
DEVICE_MODEL := DAP-1620
|
|
|
|
|
DEVICE_VARIANT := B1
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware rssileds
|
|
|
|
|
DLINK_HWID := MT76XMT7621-RP-PR2475-NA
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | \
|
|
|
|
|
check-size 11009992 | pad-to 11009992 | \
|
|
|
|
|
append-md5sum-ascii-salted ffff | \
|
|
|
|
|
append-string $$(DLINK_HWID) | \
|
|
|
|
|
check-size
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dap-1620-b1
|
|
|
|
|
|
2023-01-07 12:45:44 +00:00
|
|
|
define Device/dlink_dap-x1860-a1
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2023-01-07 12:45:44 +00:00
|
|
|
IMAGE_SIZE := 53248k
|
|
|
|
|
DEVICE_VENDOR := D-Link
|
|
|
|
|
DEVICE_MODEL := DAP-X1860
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
KERNEL_SIZE := 8192k
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
|
|
|
check-size | elx-header 011b0060 8844A2D168B45A2D
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware rssileds -uboot-envtools
|
2023-01-07 12:45:44 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dap-x1860-a1
|
|
|
|
|
|
ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
|
|
|
define Device/dlink_dir-8xx-a1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
DEVICE_VENDOR := D-Link
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2021-04-20 09:44:01 +00:00
|
|
|
KERNEL := $$(KERNEL) | uimage-sgehdr
|
ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
|
|
|
IMAGES += factory.bin
|
2021-04-20 09:44:01 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
|
|
|
check-size | append-metadata
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size
|
ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
|
|
|
endef
|
|
|
|
|
|
ramips: add support for D-Link DIR-882 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2020-10-05 14:16:44 +00:00
|
|
|
define Device/dlink_dir-8xx-r1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := D-Link
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2021-01-05 09:42:34 +00:00
|
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
2021-06-20 15:20:40 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
|
|
|
check-size | append-metadata
|
ramips: add support for D-Link DIR-882 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2020-10-05 14:16:44 +00:00
|
|
|
endef
|
|
|
|
|
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
define Device/dlink_dir-xx60-a1
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
IMAGE_SIZE := 40960k
|
|
|
|
|
DEVICE_VENDOR := D-Link
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2021-04-20 09:44:01 +00:00
|
|
|
KERNEL := $$(KERNEL) | uimage-sgehdr
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
|
|
|
check-size
|
|
|
|
|
endef
|
|
|
|
|
|
ramips: add support for D-Link DIR-1935 A1
Add support for D-Link DIR-1935 A1 based on similarities to DIR-882 A1,
DIR-867 A1 and other DIR-8xx A1 models. Existing DIR-882 A1 openwrt
"factory" firmware installs without modificaitons via the D-Link
Recovery GUI and has no known incompatibilities with the DIR-1935 A1.
Changes to be committed:
new file: target/linux/ramips/dts/mt7621_dlink_dir-1935-a1.dts
modified: target/linux/ramips/image/mt7621.mk
modified: target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
Specifications:
* Board: Not known
* SoC: MediaTek MT7621 Family
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615 Family (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green)
Notes:
* 160MHz 5GHz is available in LuCi but does not appear to work (i.e. no
SSID is visible in wifi scanning apps on other devices) with either
official DIR-882 A1 firmware or a test build for the DIR-1935 A1 based
on the 22.03.2 branch. 80 MHz 5GHz works.
Serial port:
* Untested (potential user damage/error)
* Expected to be identical to other DIR-8xx A1 models:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Keith Harrison <keithh@protonmail.com>
2023-01-07 15:23:03 +00:00
|
|
|
define Device/dlink_dir-1935-a1
|
|
|
|
|
$(Device/dlink_dir-8xx-a1)
|
|
|
|
|
DEVICE_MODEL := DIR-1935
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
DEVICE_PACKAGES += kmod-usb3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-1935-a1
|
|
|
|
|
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
define Device/dlink_dir-1960-a1
|
|
|
|
|
$(Device/dlink_dir-xx60-a1)
|
|
|
|
|
DEVICE_MODEL := DIR-1960
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-1960-a1
|
|
|
|
|
|
ramips: add support for D-Link DIR-2640 A1
This patch adds support for D-Link DIR-2640 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue),
WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: James McGuire <jamesm51@gmail.com>
[fix device definition title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-05 05:13:19 +00:00
|
|
|
define Device/dlink_dir-2640-a1
|
|
|
|
|
$(Device/dlink_dir-xx60-a1)
|
|
|
|
|
DEVICE_MODEL := DIR-2640
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-2640-a1
|
|
|
|
|
|
ramips: add support for D-Link DIR-2660 A1
This patch adds support for D-Link DIR-2660 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white), USB 2.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[rebase onto already merged DIR-1960 A1, add MAC addresses to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
define Device/dlink_dir-2660-a1
|
|
|
|
|
$(Device/dlink_dir-xx60-a1)
|
|
|
|
|
DEVICE_MODEL := DIR-2660
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-2660-a1
|
|
|
|
|
|
2022-08-25 06:10:13 +00:00
|
|
|
define Device/dlink_dir-3060-a1
|
|
|
|
|
$(Device/dlink_dir-xx60-a1)
|
|
|
|
|
DEVICE_MODEL := DIR-3060
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-3060-a1
|
|
|
|
|
|
ramips: add support for D-Link Dir-853 A1
Specifications:
* SoC: MT7621AT
* RAM: 256MB (NT5CC64M16GP-DI)
* Flash: 16MB NOR SPI flash (GD25Q127CSIG, using GD25Q128C driver)
* WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC
* Ethernet: 4x1000M LAN, 1x 1000M WAN
* LEDs: Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue,
USB Blue
* Buttons: Reset,WPS, Wifi
* Serial interface: on board but not populated, pinout (from the DC jack
side to the WAN port side) is "3.3V Input Output Gnd". Baud rate is 57600,
settings are 8 data bits, no parity bit, one stop bit, and no flow control.
Stock flash layout:
```
GD25Q128C(c8 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K)
.numeraseregions = 0
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "Config2"
0x000000060000-0x000000fb0000 : "Kernel"
0x000000fb0000-0x000001000000 : "Private"
```
The kernel partition will be replaced with the OpenWrt image, the other
partitions are left untouched.
"Config2" seems to be the config storage used by the stock firmware.
"Private" is a 320kB empty JFFS2 partition that comes with the stock
firmware. One can get a larger space for OpenWrt by merging it with
"Kernel".
OpenWrt flash layout:
```
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "u-boot-env"
0x000000040000-0x000000050000 : "factory"
0x000000050000-0x000000060000 : "config2_stock"
0x000000060000-0x000000fb0000 : "firmware"
0x000000fb0000-0x000001000000 : "private_stock"
```
The OpenWrt image must have 96 bytes of padding in the header.
MAC addresses on OEM firmware:
| | location on the flash | notes |
|------ |----------------------- |---------- |
| lan (eth2) | factory + 0xe000 | on label |
| wan (eth3) | factory + 0xe006 | |
| 2.4g (rax0) | not on flash | lan + 1 |
| 5g (ra0) | not on flash | lan + 2 |
Mac addresses of the 2.4g and 5g interface are stored as ASCII strings in
the u-boot-env partition, but they are not used. OpenWrt calculates
Wifi Mac addresses based on the LAN Mac.
Flash and test instructions:
Flash the encrypted image (available in the OpenWrt forum) through the
stock D-Dink web interface.
1. Open the case, and solder the 4-pin header near the WAN port.
2. Connect it to a USB-UART TTL (3.3V) adapter, no need to connect VCC.
3. Open a terminal emulator (e.g. `screen /dev/ttyUSB0` on linux) with
the settings mentioned above.
4. Setup a TFTP server on your PC that can serve
`xxx-ramips-mt7621-dlink_dir-853-a1-initramfs-kernel.bin`.
5. Connect any LAN port to your PC and set a static IPv4 address to
192.168.0.101 (netmask 255.255.255.0).
6. Power on the device and keeps pressing 1 until you see the prompt.
7. Use default IP addresses and enter the file name accordingly, then hit
enter.
8. Wait until it boots to OpenWrt, the default IP address is 192.168.1.1,
you need to change your PC network adapter to use DHCP in order to access
LUCI.
9. So far, the OpenWrt runs in RAM and the flash contents are not touched.
You can try OpenWrt without having to overwrite the stock firmware, a
reboot clears all changes.
10. Optionally, backup the stock firmware (the "firmware" partition) in
Luci.
11. To permantly install OpenWrt to the device , click
on "System -> Backup/Flash Firmware" in Luci and flash
`xxx-ramips-mt7621-dlink_dir-853-a1-squashfs-sysupgrade.bin`
Known problems:
* WLAN0 defaults to 5G after a fresh installation, to enable 2.4G network,
you need to config it manually in LUCI.
* If you see jffs2 related warnings/errors after updating from the stock
web interface, you need to do a reset in LUCI. The error will be gone after
a cold reboot.
Signed-off-by: Hang Zhou <929513338qq@gmail.com>
2023-02-26 09:13:33 +00:00
|
|
|
define Device/dlink_dir-853-a1
|
|
|
|
|
$(Device/dlink_dir-8xx-a1)
|
|
|
|
|
DEVICE_MODEL := DIR-853
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-853-a1
|
|
|
|
|
|
ramips: add support for D-Link DIR-853 A3
Specifications:
* SoC: MT7621AT
* RAM: 256MB
* Flash: 128MB NAND flash
* WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC
* LAN: 5x1000M
* Firmware layout is Uboot with extra 96 bytes in header
* Base PCB is DIR-1360 REV1.0
* LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue,
USB Blue
* Buttons Reset,WPS, Wifi
MAC addresses on OEM firmware:
lan factory 0xe000 f4:*:*:a8:*:65 (label)
wan factory 0xe006 f4:*:*:a8:*:68
2.4 GHz [not on flash] f6:*:*:c8:*:66
5.0 GHz factory 0x4 f4:*:*:a8:*:66
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
f4:XX:XX:a8:XX:66 f6:XX:XX:c8:XX:66 +0x20
x0:xx:xx:68:xx:xx x2:xx:xx:48:xx:xx -0x20
x4:xx:xx:6a:xx:xx x6:xx:xx:4a:xx:xx -0x20
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Flashing instruction:
The Dlink "Emergency Room" cannot be accessed through the reset
button on this device. You can either use console or use the
encrypted factory image availble in the openwrt forum.
Once the encrypted image is flashed throuh the stock Dlink web
interface, the sysupgrade images can be used.
Header pins needs to be soldered near the WPS and Wifi buttons.
The layout for the pins is (VCC,RX,TX,GND). No need to connect the VCC.
the settings are:
Bps/Par/Bits : 57600 8N1
Hardware Flow Control : No
Software Flow Control : No
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device
At the time of adding support the wireless config needs to be set up by
editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LUCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Signed-off-by: Karim Dehouche <karimdplay@gmail.com>
[rebase, improve MAC table, update wireless config comment, fix
2.4g macaddr setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-18 07:19:16 +00:00
|
|
|
define Device/dlink_dir-853-a3
|
|
|
|
|
$(Device/dlink_dir-xx60-a1)
|
|
|
|
|
DEVICE_MODEL := DIR-853
|
|
|
|
|
DEVICE_VARIANT := A3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-853-a3
|
|
|
|
|
|
ramips: add support for D-Link DIR-853-R1
This PR adds support for router D-Link DIR-853-R1
Specifications:
SoC: MT7621AT
RAM: 128MB
Flash: 16MB SPI
WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC (This mode allows this
single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time)
LAN: 5x1000M
LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue
USB Blue
Buttons Reset,WPS, Wifi
MAC addresses:
|Interface | MAC | Factory |Comment
|------------|-----------------|-------------|----------------
|WAN sticker |C4:XX:XX:6E:XX:2A| |Sticker
|LAN |C4:XX:XX:6E:XX:2B| |
|Wifi (5g) |C4:XX:XX:6E:XX:2C|0x4 |
|Wifi (2.4g) |C6:XX:XX:7E:XX:2C| |
| | | |
| |C4:XX:XX:6E:XX:2E|0x8004 0xe000|
| |C4:XX:XX:6E:XX:2F|0xe006 |
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C4:XX:XX:6E:XX:2C C6:XX:XX:7E:XX:2C 0x10
f4:XX:XX:16:XX:32 f6:XX:XX:36:XX:32 0x20
F4:XX:XX:A6:XX:E3 F6:XX:XX:B6:XX:E3 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Flashing instruction:
The Dlink "Emergency Room"
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Then, power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device.
Signed-off-by: Stas Fiduchi <fiduchi@protonmail.com>
[commit title/message improvements, use correct label MAC address,
calculate MAC addresses based on 0x4, minor DTS style fixes, add
uart2 to state_default, remove factory image, add 2.4g MAC address,
use partition DTSI, add macaddr comment in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-12 08:35:27 +00:00
|
|
|
define Device/dlink_dir-853-r1
|
|
|
|
|
$(Device/dlink_dir-8xx-r1)
|
|
|
|
|
DEVICE_MODEL := DIR-853
|
|
|
|
|
DEVICE_VARIANT := R1
|
|
|
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-853-r1
|
|
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/dlink_dir-860l-b1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2022-09-28 00:55:01 +00:00
|
|
|
$(Device/seama-lzma-loader)
|
2018-12-29 18:25:00 +00:00
|
|
|
SEAMA_SIGNATURE := wrgac13_dlink.2013gui_dir860lb
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := D-Link
|
|
|
|
|
DEVICE_MODEL := DIR-860L
|
|
|
|
|
DEVICE_VARIANT := B1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport \
|
|
|
|
|
-uboot-envtools
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += dir-860l-b1
|
2016-04-01 07:11:48 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += dlink_dir-860l-b1
|
2016-04-01 07:11:48 +00:00
|
|
|
|
ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
|
|
|
define Device/dlink_dir-867-a1
|
|
|
|
|
$(Device/dlink_dir-8xx-a1)
|
|
|
|
|
DEVICE_MODEL := DIR-867
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-867-a1
|
|
|
|
|
|
2020-07-10 03:49:20 +00:00
|
|
|
define Device/dlink_dir-878-a1
|
ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
|
|
|
$(Device/dlink_dir-8xx-a1)
|
2020-07-10 03:49:20 +00:00
|
|
|
DEVICE_MODEL := DIR-878
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-878-a1
|
|
|
|
|
|
ramips: add support for D-Link DIR-878 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
Update to the last D-Link firmware through web-ui before OpenWRT
installation then follow the instructions to patch your device using
D-Link FailsafeUI.
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.1 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Igor Nazarov <tigron.dev@gmail.com>
2022-03-16 21:51:35 +00:00
|
|
|
define Device/dlink_dir-878-r1
|
|
|
|
|
$(Device/dlink_dir-8xx-r1)
|
|
|
|
|
DEVICE_MODEL := DIR-878
|
|
|
|
|
DEVICE_VARIANT := R1
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size | \
|
|
|
|
|
sign-dlink-ru 57c5375741c30ca9ebcb36713db4ba51 \
|
|
|
|
|
ab0dff19af8842cdb70a86b4b68d23f7
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-878-r1
|
|
|
|
|
|
ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
|
|
|
define Device/dlink_dir-882-a1
|
|
|
|
|
$(Device/dlink_dir-8xx-a1)
|
|
|
|
|
DEVICE_MODEL := DIR-882
|
|
|
|
|
DEVICE_VARIANT := A1
|
|
|
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-882-a1
|
|
|
|
|
|
ramips: add support for D-Link DIR-882 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2020-10-05 14:16:44 +00:00
|
|
|
define Device/dlink_dir-882-r1
|
|
|
|
|
$(Device/dlink_dir-8xx-r1)
|
|
|
|
|
DEVICE_MODEL := DIR-882
|
|
|
|
|
DEVICE_VARIANT := R1
|
|
|
|
|
DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
|
2021-06-20 15:20:40 +00:00
|
|
|
IMAGES += factory.bin
|
ramips: add support for D-Link DIR-882 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2020-10-05 14:16:44 +00:00
|
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | check-size | \
|
2021-06-20 15:20:40 +00:00
|
|
|
sign-dlink-ru 57c5375741c30ca9ebcb36713db4ba51 \
|
|
|
|
|
ab0dff19af8842cdb70a86b4b68d23f7
|
ramips: add support for D-Link DIR-882 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2020-10-05 14:16:44 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dlink_dir-882-r1
|
|
|
|
|
|
2022-02-12 02:21:21 +00:00
|
|
|
define Device/dual-q_h721
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := Dual-Q
|
|
|
|
|
DEVICE_MODEL := H721
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 \
|
|
|
|
|
-wpad-basic-mbedtls -uboot-envtools
|
2022-02-12 02:21:21 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += dual-q_h721
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/d-team_newifi-d2
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-18 06:19:38 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
2023-04-18 13:42:41 +00:00
|
|
|
DEVICE_VENDOR := D-Team
|
|
|
|
|
DEVICE_MODEL := Newifi D2
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2018-02-22 16:08:14 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += d-team_newifi-d2
|
2018-02-22 16:08:14 +00:00
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/d-team_pbr-m1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-09-13 10:57:11 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := PandoraBox
|
|
|
|
|
DEVICE_MODEL := PBR-M1
|
2020-03-05 13:57:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb3 kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += pbr-m1
|
2018-12-08 18:55:56 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += d-team_pbr-m1
|
2018-12-08 18:55:56 +00:00
|
|
|
|
2019-11-15 22:21:22 +00:00
|
|
|
define Device/edimax_ra21s
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-07-03 05:51:03 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-11-15 22:21:22 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := Edimax
|
|
|
|
|
DEVICE_MODEL := RA21S
|
|
|
|
|
DEVICE_ALT0_VENDOR := Edimax
|
|
|
|
|
DEVICE_ALT0_MODEL := Gemini RA21S
|
|
|
|
|
IMAGES += factory.bin
|
2020-03-10 13:58:27 +00:00
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
2019-11-15 22:21:22 +00:00
|
|
|
elx-header 02020040 8844A2D168B45A2D
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2019-11-15 22:21:22 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += edimax_ra21s
|
|
|
|
|
|
2020-05-19 23:27:56 +00:00
|
|
|
define Device/edimax_re23s
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-05-19 23:27:56 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 15680k
|
|
|
|
|
DEVICE_VENDOR := Edimax
|
|
|
|
|
DEVICE_MODEL := RE23S
|
|
|
|
|
DEVICE_ALT0_VENDOR := Edimax
|
|
|
|
|
DEVICE_ALT0_MODEL := Gemini RE23S
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
|
|
|
|
|
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
2021-06-20 16:54:36 +00:00
|
|
|
check-size | append-metadata
|
2020-05-19 23:27:56 +00:00
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | \
|
|
|
|
|
edimax-header -s CSYS -m RN76 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
|
|
|
check-size
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2020-05-19 23:27:56 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += edimax_re23s
|
|
|
|
|
|
2019-09-19 19:33:59 +00:00
|
|
|
define Device/edimax_rg21s
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-07-03 05:51:03 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-09-19 19:33:59 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := Edimax
|
|
|
|
|
DEVICE_MODEL := Gemini AC2600 RG21S
|
|
|
|
|
IMAGES += factory.bin
|
2020-03-10 13:58:27 +00:00
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
2019-12-19 18:40:33 +00:00
|
|
|
elx-header 02020038 8844A2D168B45A2D
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2019-09-19 19:33:59 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += edimax_rg21s
|
|
|
|
|
|
2018-06-15 15:27:51 +00:00
|
|
|
define Device/elecom_wrc-1167ghbk2-s
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2018-06-15 15:27:51 +00:00
|
|
|
IMAGE_SIZE := 15488k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := ELECOM
|
|
|
|
|
DEVICE_MODEL := WRC-1167GHBK2-S
|
2018-06-15 15:27:51 +00:00
|
|
|
IMAGES += factory.bin
|
2020-03-10 13:58:27 +00:00
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
2020-12-17 14:58:16 +00:00
|
|
|
elecom-wrc-gs-factory WRC-1167GHBK2-S 0.00
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2018-06-15 15:27:51 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-1167ghbk2-s
|
|
|
|
|
|
2020-07-15 18:08:22 +00:00
|
|
|
define Device/elecom_wrc-gs
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-07-15 04:13:01 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := ELECOM
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
2020-12-17 14:58:16 +00:00
|
|
|
elecom-wrc-gs-factory $$$$(ELECOM_HWNAME) 0.00 -N | \
|
|
|
|
|
append-string MT7621_ELECOM_$$$$(ELECOM_HWNAME)
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2020-07-15 04:13:01 +00:00
|
|
|
endef
|
2020-07-15 18:08:22 +00:00
|
|
|
|
2020-11-28 09:41:12 +00:00
|
|
|
define Device/elecom_wrc-1167gs2-b
|
|
|
|
|
$(Device/elecom_wrc-gs)
|
|
|
|
|
IMAGE_SIZE := 11264k
|
|
|
|
|
DEVICE_MODEL := WRC-1167GS2-B
|
|
|
|
|
ELECOM_HWNAME := WRC-1167GS2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-1167gs2-b
|
|
|
|
|
|
2020-11-28 09:41:13 +00:00
|
|
|
define Device/elecom_wrc-1167gst2
|
|
|
|
|
$(Device/elecom_wrc-gs)
|
|
|
|
|
IMAGE_SIZE := 24576k
|
|
|
|
|
DEVICE_MODEL := WRC-1167GST2
|
|
|
|
|
ELECOM_HWNAME := WRC-1167GST2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-1167gst2
|
|
|
|
|
|
2020-07-15 18:08:22 +00:00
|
|
|
define Device/elecom_wrc-1750gs
|
|
|
|
|
$(Device/elecom_wrc-gs)
|
|
|
|
|
IMAGE_SIZE := 11264k
|
|
|
|
|
DEVICE_MODEL := WRC-1750GS
|
|
|
|
|
ELECOM_HWNAME := WRC-1750GS
|
|
|
|
|
endef
|
2020-07-15 04:13:01 +00:00
|
|
|
TARGET_DEVICES += elecom_wrc-1750gs
|
|
|
|
|
|
ramips: add support for ELECOM WRC-1750GST2
ELECOM WRC-1750GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB (NT5CC128M16JR-EK)
- Flash : SPI-NOR 32 MiB (MX25L25645GMI-08G)
- WLAN : 2.4/5 GHz 3T3R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 4x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX, from ethernet port side
- 57600n8
- Power : 12 VDC, 1.5 A
Flash instruction using factory image:
1. Boot WRC-1750GST2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
MAC addresses:
LAN : 04:AB:18:xx:xx:23 (Factory, 0xE000 (hex))
WAN : 04:AB:18:xx:xx:24 (Factory, 0xE006 (hex))
2.4GHz : 04:AB:18:xx:xx:25 (Factory, 0x4 (hex))
5GHz : 04:AB:18:xx:xx:26 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-03-17 09:35:34 +00:00
|
|
|
define Device/elecom_wrc-1750gst2
|
|
|
|
|
$(Device/elecom_wrc-gs)
|
|
|
|
|
IMAGE_SIZE := 24576k
|
|
|
|
|
DEVICE_MODEL := WRC-1750GST2
|
|
|
|
|
ELECOM_HWNAME := WRC-1750GST2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-1750gst2
|
|
|
|
|
|
2020-07-15 04:13:01 +00:00
|
|
|
define Device/elecom_wrc-1750gsv
|
2020-07-15 18:08:22 +00:00
|
|
|
$(Device/elecom_wrc-gs)
|
2020-07-15 04:13:01 +00:00
|
|
|
IMAGE_SIZE := 11264k
|
|
|
|
|
DEVICE_MODEL := WRC-1750GSV
|
2020-07-15 18:08:22 +00:00
|
|
|
ELECOM_HWNAME := WRC-1750GSV
|
2020-07-15 04:13:01 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-1750gsv
|
|
|
|
|
|
2018-08-18 23:05:15 +00:00
|
|
|
define Device/elecom_wrc-1900gst
|
2020-07-15 18:08:22 +00:00
|
|
|
$(Device/elecom_wrc-gs)
|
2018-08-18 23:05:15 +00:00
|
|
|
IMAGE_SIZE := 11264k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_MODEL := WRC-1900GST
|
2020-07-15 18:08:22 +00:00
|
|
|
ELECOM_HWNAME := WRC-1900GST
|
2018-08-18 23:05:15 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-1900gst
|
|
|
|
|
|
ramips: add support for ELECOM WRC-2533GHBK2-T
ELECOM WRC-2533GHBK2-T is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 4x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, RX, GND, TX from SoC side
- 57600n8
- Power : 12 VDC, 1.5 A
Flash instruction using factory image:
1. Boot WRC-2533GHBK2-T normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing
MAC addresses:
LAN : BC:5C:4C:xx:xx:FD (Config, "ethaddr" (text))
WAN : BC:5C:4C:xx:xx:FC (Config, "wanaddr" (text), Label)
2.4 GHz: BC:5C:4C:xx:xx:FE (Factory, 0x4 (hex))
5 GHz : BC:5C:4C:xx:xx:FF (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-01 12:22:20 +00:00
|
|
|
define Device/elecom_wrc-2533ghbk2-t
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := ELECOM
|
|
|
|
|
DEVICE_MODEL := WRC-2533GHBK2-T
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
|
|
|
elx-header 0107003b 8844A2D168B45A2D | \
|
|
|
|
|
elecom-product-header WRC-2533GHBK2-T
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
ramips: add support for ELECOM WRC-2533GHBK2-T
ELECOM WRC-2533GHBK2-T is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 4x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, RX, GND, TX from SoC side
- 57600n8
- Power : 12 VDC, 1.5 A
Flash instruction using factory image:
1. Boot WRC-2533GHBK2-T normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing
MAC addresses:
LAN : BC:5C:4C:xx:xx:FD (Config, "ethaddr" (text))
WAN : BC:5C:4C:xx:xx:FC (Config, "wanaddr" (text), Label)
2.4 GHz: BC:5C:4C:xx:xx:FE (Factory, 0x4 (hex))
5 GHz : BC:5C:4C:xx:xx:FF (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-01 12:22:20 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-2533ghbk2-t
|
|
|
|
|
|
ramips: add support for ELECOM WRC-2533GHBK-I
ELECOM WRC-2533GHBK-I is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 4x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, RX, GND, TX from SoC side
- 57600n8
- Power : 12VDC, 1.5A
Flash instruction using factory image:
1. Boot WRC-2533GHBK-I normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing
MAC addresses:
LAN : BC:5C:4C:xx:xx:89 (Config, ethaddr (text))
WAN : BC:5C:4C:xx:xx:88 (Config, wanaddr (text))
2.4GHz : BC:5C:4C:xx:xx:8A (Factory, 0x4 (hex))
5GHz : BC:5C:4C:xx:xx:8B (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2020-12-11 14:14:58 +00:00
|
|
|
define Device/elecom_wrc-2533ghbk-i
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := ELECOM
|
|
|
|
|
DEVICE_MODEL := WRC-2533GHBK-I
|
|
|
|
|
IMAGE_SIZE := 9856k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
|
|
|
|
elx-header 0107002d 8844A2D168B45A2D | \
|
|
|
|
|
elecom-product-header WRC-2533GHBK-I
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
ramips: add support for ELECOM WRC-2533GHBK-I
ELECOM WRC-2533GHBK-I is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 4x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, RX, GND, TX from SoC side
- 57600n8
- Power : 12VDC, 1.5A
Flash instruction using factory image:
1. Boot WRC-2533GHBK-I normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing
MAC addresses:
LAN : BC:5C:4C:xx:xx:89 (Config, ethaddr (text))
WAN : BC:5C:4C:xx:xx:88 (Config, wanaddr (text))
2.4GHz : BC:5C:4C:xx:xx:8A (Factory, 0x4 (hex))
5GHz : BC:5C:4C:xx:xx:8B (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2020-12-11 14:14:58 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-2533ghbk-i
|
|
|
|
|
|
ramips: add support for ELECOM WRC-2533GS2
ELECOM WRC-2533GS2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB (NT5CC64M16GP-DI)
- Flash : SPI-NOR 16 MiB (MX25L12835FM2I-10G)
- WLAN : 2.4/5GHz 4T4R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 4x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from ethernet port side
- 57600n8
- Power : 12 VDC, 1.5 A
Flash instruction using factory image:
1. Boot WRC-2533GS2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
MAC Addresses:
LAN : 04:AB:18:xx:xx:FB (Factory, 0xFFF4 (hex))
WAN : 04:AB:18:xx:xx:FC (Factory, 0xFFFA (hex))
2.4 GHz : 04:AB:18:xx:xx:FD (Factory, 0x4 (hex))
5 GHz : 04:AB:18:xx:xx:FE (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-02-05 10:09:11 +00:00
|
|
|
define Device/elecom_wrc-2533gs2
|
|
|
|
|
$(Device/elecom_wrc-gs)
|
|
|
|
|
IMAGE_SIZE := 11264k
|
|
|
|
|
DEVICE_MODEL := WRC-2533GS2
|
|
|
|
|
ELECOM_HWNAME := WRC-2533GS2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-2533gs2
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/elecom_wrc-2533gst
|
2020-07-15 18:08:22 +00:00
|
|
|
$(Device/elecom_wrc-gs)
|
2019-07-07 14:27:51 +00:00
|
|
|
IMAGE_SIZE := 11264k
|
|
|
|
|
DEVICE_MODEL := WRC-2533GST
|
2020-07-15 18:08:22 +00:00
|
|
|
ELECOM_HWNAME := WRC-2533GST
|
2017-02-27 20:59:50 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += elecom_wrc-2533gst
|
2017-02-27 20:59:50 +00:00
|
|
|
|
2020-05-16 08:39:26 +00:00
|
|
|
define Device/elecom_wrc-2533gst2
|
2020-07-15 18:08:22 +00:00
|
|
|
$(Device/elecom_wrc-gs)
|
2020-05-16 08:39:26 +00:00
|
|
|
IMAGE_SIZE := 24576k
|
|
|
|
|
DEVICE_MODEL := WRC-2533GST2
|
2020-07-15 18:08:22 +00:00
|
|
|
ELECOM_HWNAME := WRC-2533GST2
|
2020-05-16 08:39:26 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += elecom_wrc-2533gst2
|
|
|
|
|
|
ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface under admin account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following line:
<PARAMETER name="Password" type="string" value="<your router serial \
is here>" writable="1" encryption="1" password="1"/>
5. Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
ETxxxxxxxxxx is the serial number from the backplate label)
9. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:50 |
| WAN | label + 11 | *:5b |
| 2g | label + 2 | *:52 |
| 5g | label + 3 | *:53 |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-27 14:01:58 +00:00
|
|
|
define Device/etisalat_s3
|
|
|
|
|
$(Device/sercomm_dxx)
|
|
|
|
|
IMAGE_SIZE := 32768k
|
|
|
|
|
SERCOMM_HWID := DDK
|
|
|
|
|
SERCOMM_HWVER := 10000
|
|
|
|
|
SERCOMM_SWVER := 4009
|
|
|
|
|
DEVICE_VENDOR := Etisalat
|
|
|
|
|
DEVICE_MODEL := S3
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware kmod-usb3
|
ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface under admin account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following line:
<PARAMETER name="Password" type="string" value="<your router serial \
is here>" writable="1" encryption="1" password="1"/>
5. Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
ETxxxxxxxxxx is the serial number from the backplate label)
9. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:50 |
| WAN | label + 11 | *:5b |
| 2g | label + 2 | *:52 |
| 5g | label + 3 | *:53 |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-27 14:01:58 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += etisalat_s3
|
|
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/firefly_firewrt
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := Firefly
|
|
|
|
|
DEVICE_MODEL := FireWRT
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport \
|
|
|
|
|
-uboot-envtools
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += firewrt
|
2016-04-01 07:11:48 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += firefly_firewrt
|
2016-04-01 07:11:48 +00:00
|
|
|
|
2018-12-27 05:39:16 +00:00
|
|
|
define Device/gehua_ghl-r-001
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := GeHua
|
|
|
|
|
DEVICE_MODEL := GHL-R-001
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2018-12-27 05:39:16 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += gehua_ghl-r-001
|
|
|
|
|
|
2020-12-16 07:58:28 +00:00
|
|
|
define Device/glinet_gl-mt1300
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 32448k
|
|
|
|
|
DEVICE_VENDOR := GL.iNet
|
|
|
|
|
DEVICE_MODEL := GL-MT1300
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 -uboot-envtools
|
2020-12-16 07:58:28 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += glinet_gl-mt1300
|
|
|
|
|
|
2018-05-27 00:26:14 +00:00
|
|
|
define Device/gnubee_gb-pc1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2022-07-05 14:10:43 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := GnuBee
|
|
|
|
|
DEVICE_MODEL := Personal Cloud One
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 \
|
|
|
|
|
-wpad-basic-mbedtls -uboot-envtools
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
2017-07-22 01:15:56 +00:00
|
|
|
endef
|
2018-05-27 00:26:14 +00:00
|
|
|
TARGET_DEVICES += gnubee_gb-pc1
|
2017-07-22 01:15:56 +00:00
|
|
|
|
2018-02-17 08:54:57 +00:00
|
|
|
define Device/gnubee_gb-pc2
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2022-07-05 14:10:43 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := GnuBee
|
|
|
|
|
DEVICE_MODEL := Personal Cloud Two
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620 \
|
|
|
|
|
-wpad-basic-mbedtls -uboot-envtools
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
2018-02-05 00:24:15 +00:00
|
|
|
endef
|
2018-02-17 08:54:57 +00:00
|
|
|
TARGET_DEVICES += gnubee_gb-pc2
|
2018-02-05 00:24:15 +00:00
|
|
|
|
2023-03-21 06:49:22 +00:00
|
|
|
define Device/hanyang_hyc-g920
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := Hanyang
|
|
|
|
|
DEVICE_MODEL := CJ-Hello HYC-G920
|
|
|
|
|
IMAGE_SIZE := 15744k
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt76x2 kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += hanyang_hyc-g920
|
|
|
|
|
|
2022-03-20 15:42:37 +00:00
|
|
|
define Device/h3c_tx180x
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-03-20 15:42:37 +00:00
|
|
|
KERNEL_SIZE := 8192k
|
|
|
|
|
IMAGE_SIZE := 120832k
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL_INITRAMFS := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
KERNEL := $$(KERNEL_INITRAMFS) | h3c-blank-header
|
|
|
|
|
DEVICE_VENDOR := H3C
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
2022-03-20 15:42:37 +00:00
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/h3c_tx1800-plus
|
|
|
|
|
$(Device/h3c_tx180x)
|
|
|
|
|
DEVICE_MODEL := TX1800 Plus
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += h3c_tx1800-plus
|
|
|
|
|
|
|
|
|
|
define Device/h3c_tx1801-plus
|
|
|
|
|
$(Device/h3c_tx180x)
|
|
|
|
|
DEVICE_MODEL := TX1801 Plus
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += h3c_tx1801-plus
|
|
|
|
|
|
|
|
|
|
define Device/h3c_tx1806
|
|
|
|
|
$(Device/h3c_tx180x)
|
|
|
|
|
DEVICE_MODEL := TX1806
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += h3c_tx1806
|
|
|
|
|
|
2022-09-15 17:10:52 +00:00
|
|
|
define Device/haier-sim_wr1800k
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-09-15 17:10:52 +00:00
|
|
|
IMAGE_SIZE := 125440k
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
2022-12-12 11:25:45 +00:00
|
|
|
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
|
|
|
|
|
ARTIFACTS := initramfs-factory.bin
|
|
|
|
|
ARTIFACT/initramfs-factory.bin := append-image-stage initramfs-kernel.bin | \
|
|
|
|
|
haier-sim_wr1800k-factory
|
|
|
|
|
endif
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
2022-09-15 17:10:52 +00:00
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/haier_har-20s2u1
|
|
|
|
|
$(Device/haier-sim_wr1800k)
|
|
|
|
|
DEVICE_VENDOR := Haier
|
|
|
|
|
DEVICE_MODEL := HAR-20S2U1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += haier_har-20s2u1
|
|
|
|
|
|
ramips: add support for HiLink HLK-7621A evaluation board
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB (DDR3)
- Flash: 32 MB SPI NOR 44MHz
- Switch: 1 WAN, 4 LAN (Gigabit)
- LEDs: 1 WAN, 4 LAN (controlled by PHY)
- USB Ports: 1 x USB2, 1 x USB3
- WLAN: 1 x 2.4, 5 GHz 866Mbps (MT7612E)
- Button: 1 button (reset)
- UART Serial: UART1 as console : 57600 baud
- Power: 12VDC, 1A
Installation:
Update openWRT firmware using internal GNUBEE uboot:
https://github.com/gnubee-git/GnuBee-MT7621-uboot
By HTTP: Initial uboot address is http://10.10.10.123, your address
needs to be 10.10.10.x, and mask 255.255.255.0.
By TFTP: Uboot is in client mode, the address of the firmware must
be tftp://10.10.10.3/uboot.bin
Recovery:
Manufacturer provides MTK OpenWrt 14.07 source code, compile then
flash it by uboot.
HLK-7621A is a stamp hole package module for embedded development,
users have to design IO boards to use it.
MAC addresses:
- u-boot-env contains a placeholder address:
> mtd_get_mac_ascii u-boot-env ethaddr
03:17:73:ab:cd:ef
- phy0 gets a valid-looking address:
> cat /sys/class/ieee80211/phy0/macaddress
f8:62:aa:**:**:a8
- Calibration data for &pcie2 contains a valid address, however the
zeros in the right half look like it's not real:
8c:88:2b:00:00:1b
- Since it's an evaluation board and there is no solid information
about the MAC address assignment, the ethernet MAC address is left random.
Signed-off-by: Chen Yijun <cyjason@bupt.edu.cn>
[add keys and pcie nodes to properly support evaluation board]
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[remove ethernet address, wrap lines properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-04-04 06:50:26 +00:00
|
|
|
define Device/hilink_hlk-7621a-evb
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := HiLink
|
|
|
|
|
DEVICE_MODEL := HLK-7621A evaluation board
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt76x2 kmod-usb3 -uboot-envtools
|
ramips: add support for HiLink HLK-7621A evaluation board
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB (DDR3)
- Flash: 32 MB SPI NOR 44MHz
- Switch: 1 WAN, 4 LAN (Gigabit)
- LEDs: 1 WAN, 4 LAN (controlled by PHY)
- USB Ports: 1 x USB2, 1 x USB3
- WLAN: 1 x 2.4, 5 GHz 866Mbps (MT7612E)
- Button: 1 button (reset)
- UART Serial: UART1 as console : 57600 baud
- Power: 12VDC, 1A
Installation:
Update openWRT firmware using internal GNUBEE uboot:
https://github.com/gnubee-git/GnuBee-MT7621-uboot
By HTTP: Initial uboot address is http://10.10.10.123, your address
needs to be 10.10.10.x, and mask 255.255.255.0.
By TFTP: Uboot is in client mode, the address of the firmware must
be tftp://10.10.10.3/uboot.bin
Recovery:
Manufacturer provides MTK OpenWrt 14.07 source code, compile then
flash it by uboot.
HLK-7621A is a stamp hole package module for embedded development,
users have to design IO boards to use it.
MAC addresses:
- u-boot-env contains a placeholder address:
> mtd_get_mac_ascii u-boot-env ethaddr
03:17:73:ab:cd:ef
- phy0 gets a valid-looking address:
> cat /sys/class/ieee80211/phy0/macaddress
f8:62:aa:**:**:a8
- Calibration data for &pcie2 contains a valid address, however the
zeros in the right half look like it's not real:
8c:88:2b:00:00:1b
- Since it's an evaluation board and there is no solid information
about the MAC address assignment, the ethernet MAC address is left random.
Signed-off-by: Chen Yijun <cyjason@bupt.edu.cn>
[add keys and pcie nodes to properly support evaluation board]
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[remove ethernet address, wrap lines properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-04-04 06:50:26 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += hilink_hlk-7621a-evb
|
|
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/hiwifi_hc5962
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-10-18 06:55:46 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-15 12:55:24 +00:00
|
|
|
IMAGE_SIZE := 32768k
|
2017-02-22 12:47:22 +00:00
|
|
|
IMAGES += factory.bin
|
2019-12-19 18:40:33 +00:00
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
2020-03-10 13:58:27 +00:00
|
|
|
check-size
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := HiWiFi
|
|
|
|
|
DEVICE_MODEL := HC5962
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 -uboot-envtools
|
2017-02-22 12:47:22 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += hiwifi_hc5962
|
2017-02-22 12:47:22 +00:00
|
|
|
|
2021-11-13 16:03:24 +00:00
|
|
|
define Device/humax_e10
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
|
DEVICE_VENDOR := HUMAX
|
|
|
|
|
DEVICE_MODEL := E10
|
|
|
|
|
DEVICE_ALT0_VENDOR := HUMAX
|
|
|
|
|
DEVICE_ALT0_MODEL := QUANTUM E10
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
|
|
|
|
|
edimax-header -s CSYS -m EA03 -f 0x70000 -S 0x01100000 | pad-rootfs | \
|
|
|
|
|
check-size | append-metadata
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
|
|
|
edimax-header -s CSYS -m EA03 -f 0x70000 -S 0x01100000 | \
|
|
|
|
|
check-size | zip upg -P f013c26cf0a320fb71d03356dcb6bb63
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 -uboot-envtools
|
2021-11-13 16:03:24 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += humax_e10
|
|
|
|
|
|
2023-02-04 07:52:29 +00:00
|
|
|
define Device/huasifei_ws1208v2
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := Huasifei
|
|
|
|
|
DEVICE_MODEL := WS1208V2
|
|
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
|
|
|
|
kmod-usb3 kmod-usb-net-cdc-mbim kmod-usb-net-qmi-wwan \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-serial-option -uboot-envtools
|
2023-02-04 07:52:29 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += huasifei_ws1208v2
|
|
|
|
|
|
ramips: add support for I-O DATA WN-AX1167GR
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Stock firmware:
In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.
(excerpt from dmesg):
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.
If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.
(example):
## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1 !!
## Booting image at bc060000 ...
Image Name: MIPS OpenWrt Linux-4.14.50
Image Type: MIPS Linux kernel Image (lzma compressed)
Data Size: 1865917 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!
Starting kernel ...
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-27 13:47:13 +00:00
|
|
|
define Device/iodata_wn-ax1167gr
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-24 05:51:53 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
ramips: add support for I-O DATA WN-AX1167GR
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Stock firmware:
In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.
(excerpt from dmesg):
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.
If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.
(example):
## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1 !!
## Booting image at bc060000 ...
Image Name: MIPS OpenWrt Linux-4.14.50
Image Type: MIPS Linux kernel Image (lzma compressed)
Data Size: 1865917 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!
Starting kernel ...
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-27 13:47:13 +00:00
|
|
|
IMAGE_SIZE := 15552k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := I-O DATA
|
|
|
|
|
DEVICE_MODEL := WN-AX1167GR
|
2022-11-30 13:10:57 +00:00
|
|
|
ARTIFACTS := initramfs-factory.bin
|
|
|
|
|
ARTIFACT/initramfs-factory.bin := append-image-stage initramfs-kernel.bin | \
|
|
|
|
|
check-size 7680k | senao-header -r 0x30a -p 0x1055 -t 4
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 -uboot-envtools
|
ramips: add support for I-O DATA WN-AX1167GR
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Stock firmware:
In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.
(excerpt from dmesg):
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.
If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.
(example):
## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1 !!
## Booting image at bc060000 ...
Image Name: MIPS OpenWrt Linux-4.14.50
Image Type: MIPS Linux kernel Image (lzma compressed)
Data Size: 1865917 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!
Starting kernel ...
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-27 13:47:13 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-ax1167gr
|
|
|
|
|
|
2020-04-27 10:07:01 +00:00
|
|
|
define Device/iodata_nand
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2020-04-27 10:07:01 +00:00
|
|
|
DEVICE_VENDOR := I-O DATA
|
2019-08-26 11:27:22 +00:00
|
|
|
IMAGE_SIZE := 51200k
|
2020-04-26 03:24:33 +00:00
|
|
|
LOADER_TYPE := bin
|
|
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | lzma | uImage lzma
|
2020-04-27 10:07:01 +00:00
|
|
|
endef
|
|
|
|
|
|
2020-11-04 09:21:14 +00:00
|
|
|
# The OEM webinterface expects an kernel with initramfs which has the uImage
|
|
|
|
|
# header field ih_name.
|
|
|
|
|
# We don't want to set the header name field for the kernel include in the
|
|
|
|
|
# sysupgrade image as well, as this image shouldn't be accepted by the OEM
|
|
|
|
|
# webinterface. It will soft-brick the board.
|
|
|
|
|
|
2020-04-27 10:07:01 +00:00
|
|
|
define Device/iodata_wn-ax1167gr2
|
|
|
|
|
$(Device/iodata_nand)
|
|
|
|
|
DEVICE_MODEL := WN-AX1167GR2
|
2020-04-28 14:45:41 +00:00
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
2020-11-04 09:21:14 +00:00
|
|
|
uImage lzma -M 0x434f4d42 -n '3.10(XBC.1)b10' | iodata-mstc-header
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2019-08-26 11:27:22 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-ax1167gr2
|
|
|
|
|
|
ramips: add support for I-O DATA WN-AX2033GR
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.
Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V
This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.
Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".
Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-06 03:00:47 +00:00
|
|
|
define Device/iodata_wn-ax2033gr
|
2020-04-27 10:07:01 +00:00
|
|
|
$(Device/iodata_nand)
|
ramips: add support for I-O DATA WN-AX2033GR
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.
Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V
This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.
Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".
Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-06 03:00:47 +00:00
|
|
|
DEVICE_MODEL := WN-AX2033GR
|
2020-04-28 14:45:41 +00:00
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
2020-11-04 09:21:14 +00:00
|
|
|
uImage lzma -M 0x434f4d42 -n '3.10(VST.1)C10' | iodata-mstc-header
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware -uboot-envtools
|
ramips: add support for I-O DATA WN-AX2033GR
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.
Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V
This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.
Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".
Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-06 03:00:47 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-ax2033gr
|
|
|
|
|
|
2019-04-09 05:48:31 +00:00
|
|
|
define Device/iodata_wn-dx1167r
|
2020-04-27 10:07:01 +00:00
|
|
|
$(Device/iodata_nand)
|
2019-04-09 05:48:31 +00:00
|
|
|
DEVICE_MODEL := WN-DX1167R
|
2020-04-28 14:45:41 +00:00
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
2020-11-04 09:21:14 +00:00
|
|
|
uImage lzma -M 0x434f4d43 -n '3.10(XIK.1)b10' | iodata-mstc-header
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2019-04-09 05:48:31 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-dx1167r
|
|
|
|
|
|
ramips: add support for I-O DATA WN-DX1200GR
I-O DATA WN-DX1200GR is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : raw NAND 128 MiB
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : MediaTek MT7603E
- 5 GHz : MediaTek MT7613BE
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LEDs/keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle-mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX1200GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, perform sysupgrade with the
squashfs-sysupgrade image
5. Wait ~120 seconds to complete flashing
Notes:
- currently, mt7615e driver in mt76 doesn't fully support MT7613
(MT7663) wifi chip
- the eeprom data in flash is not used by mt7615e driver and the
driver reports the tx-power up to 3dBm
- the correct MAC address for MT7613BE in eeprom data cannot be
assigned to the phy
- last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D43 ("COMC")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
MAC addresses:
LAN: 50:41:B9:xx:xx:08 (Ubootenv, ethaddr (text) / Factory, 0x1E000 (hex))
WAN: 50:41:B9:xx:xx:0A (Factory, 0x1E006 (hex))
2.4GHz: 50:41:B9:xx:xx:08 (Factory, 0x4 (hex))
5GHz: 50:41:B9:xx:xx:09 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add check whether dflag_offset is set]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-26 14:50:51 +00:00
|
|
|
define Device/iodata_wn-dx1200gr
|
|
|
|
|
$(Device/iodata_nand)
|
|
|
|
|
DEVICE_MODEL := WN-DX1200GR
|
|
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
|
|
|
uImage lzma -M 0x434f4d43 -n '3.10(XIQ.0)b20' | iodata-mstc-header
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
ramips: add support for I-O DATA WN-DX1200GR
I-O DATA WN-DX1200GR is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : raw NAND 128 MiB
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : MediaTek MT7603E
- 5 GHz : MediaTek MT7613BE
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (SoC)
- LEDs/keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle-mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX1200GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, perform sysupgrade with the
squashfs-sysupgrade image
5. Wait ~120 seconds to complete flashing
Notes:
- currently, mt7615e driver in mt76 doesn't fully support MT7613
(MT7663) wifi chip
- the eeprom data in flash is not used by mt7615e driver and the
driver reports the tx-power up to 3dBm
- the correct MAC address for MT7613BE in eeprom data cannot be
assigned to the phy
- last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D43 ("COMC")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
MAC addresses:
LAN: 50:41:B9:xx:xx:08 (Ubootenv, ethaddr (text) / Factory, 0x1E000 (hex))
WAN: 50:41:B9:xx:xx:0A (Factory, 0x1E006 (hex))
2.4GHz: 50:41:B9:xx:xx:08 (Factory, 0x4 (hex))
5GHz: 50:41:B9:xx:xx:09 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add check whether dflag_offset is set]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-26 14:50:51 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-dx1200gr
|
|
|
|
|
|
ramips: add support for I-O DATA WN-DX2033GR
I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, MediaTek MT7603E
- 5 GHz : 4T4R, MediaTek MT7615
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
it is certified under the same radio-wave related regulations in Japan
- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
- There are 2x important flags in the flash:
- bootnum : select os partition for booting (persist, 0x4)
- 0x01: firmware
- 0x02: firmware_2
- debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
(Factory, 0xFE75)
- 0x00: disable debug
- 0x01: enable debug
MAC addresses:
LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-18 12:39:04 +00:00
|
|
|
define Device/iodata_wn-dx2033gr
|
|
|
|
|
$(Device/iodata_nand)
|
|
|
|
|
DEVICE_MODEL := WN-DX2033GR
|
|
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | loader-kernel | lzma | \
|
|
|
|
|
uImage lzma -M 0x434f4d42 -n '3.10(XID.0)b30' | iodata-mstc-header
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware -uboot-envtools
|
ramips: add support for I-O DATA WN-DX2033GR
I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, MediaTek MT7603E
- 5 GHz : 4T4R, MediaTek MT7615
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
it is certified under the same radio-wave related regulations in Japan
- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
- There are 2x important flags in the flash:
- bootnum : select os partition for booting (persist, 0x4)
- 0x01: firmware
- 0x02: firmware_2
- debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
(Factory, 0xFE75)
- 0x00: disable debug
- 0x01: enable debug
MAC addresses:
LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-18 12:39:04 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-dx2033gr
|
|
|
|
|
|
ramips: add support for I-O DATA WN-GX300GR
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.
Specification:
- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-05-16 12:42:48 +00:00
|
|
|
define Device/iodata_wn-gx300gr
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-24 05:51:53 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-15 12:55:40 +00:00
|
|
|
IMAGE_SIZE := 7616k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := I-O DATA
|
|
|
|
|
DEVICE_MODEL := WN-GX300GR
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 -uboot-envtools
|
ramips: add support for I-O DATA WN-GX300GR
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.
Specification:
- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-05-16 12:42:48 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wn-gx300gr
|
|
|
|
|
|
2019-07-11 05:41:08 +00:00
|
|
|
define Device/iodata_wnpr2600g
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-24 05:51:53 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-11 05:41:08 +00:00
|
|
|
DEVICE_VENDOR := I-O DATA
|
|
|
|
|
DEVICE_MODEL := WNPR2600G
|
|
|
|
|
IMAGE_SIZE := 13952k
|
|
|
|
|
IMAGES += factory.bin
|
2020-03-10 13:58:27 +00:00
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | \
|
2019-12-19 18:40:33 +00:00
|
|
|
elx-header 0104003a 8844A2D168B45A2D
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2019-07-11 05:41:08 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iodata_wnpr2600g
|
|
|
|
|
|
2022-02-11 14:18:39 +00:00
|
|
|
define Device/iptime_a3002mesh
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 16128k
|
|
|
|
|
UIMAGE_NAME := a3002me
|
|
|
|
|
DEVICE_VENDOR := ipTIME
|
|
|
|
|
DEVICE_MODEL := A3002MESH
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2022-02-11 14:18:39 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iptime_a3002mesh
|
|
|
|
|
|
2021-10-13 01:04:44 +00:00
|
|
|
define Device/iptime_a3004ns-dual
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16128k
|
|
|
|
|
UIMAGE_NAME := a3004nd
|
|
|
|
|
DEVICE_VENDOR := ipTIME
|
|
|
|
|
DEVICE_MODEL := A3004NS-dual
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt76x2 kmod-usb-ledtrig-usbport \
|
|
|
|
|
-uboot-envtools
|
2021-10-13 01:04:44 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iptime_a3004ns-dual
|
|
|
|
|
|
2021-12-22 06:59:00 +00:00
|
|
|
define Device/iptime_a3004t
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2021-12-22 06:59:00 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
FILESYSTEMS := squashfs
|
|
|
|
|
IMAGE_SIZE := 129280k
|
|
|
|
|
UIMAGE_NAME := a3004t
|
|
|
|
|
DEVICE_VENDOR := ipTIME
|
|
|
|
|
DEVICE_MODEL := A3004T
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 -uboot-envtools
|
2021-12-22 06:59:00 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iptime_a3004t
|
|
|
|
|
|
ramips: add support for ipTIME A6004NS-M
ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MediaTek MT7621A (880MHz, Duel-Core)
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB (Winbond W25Q128BV)
- WiFi: MediaTek MT7615E (2.4GHz, 5GHz)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated)
- USB: USB 3.0 x1
- UART: [3.3V, TX, RX, GND] (57600 8N1)
Installation via web interface:
1. Flash initramfs image using OEM's Firmware Update page.
2. Connect to OpenWrt with an SSH connection to `192.168.1.1`.
3. Perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Flash stock firmware via OEM's Recovery mode
How to use OEM's Recovery mode:
1. Power on the device and connect the shell through UART.
2. Connect to the shell and press the `t` key on the keyboard.
3. Set fixed IP with `192.168.0.2` with subnet mask `255.255.255.0`
4. Flash image via TFTP to `192.168.0.1`
Additional Notes:
1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz.
2. If the 5Ghz frequency is too high, 5Ghz may not work.
3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi).
Signed-off-by: SeongUk Moon <antegral@antegral.net>
[convert CRLF to LF]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-14 12:54:05 +00:00
|
|
|
define Device/iptime_a6004ns-m
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 16128k
|
|
|
|
|
UIMAGE_NAME := a6004nm
|
|
|
|
|
DEVICE_VENDOR := ipTIME
|
|
|
|
|
DEVICE_MODEL := A6004NS-M
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
ramips: add support for ipTIME A6004NS-M
ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MediaTek MT7621A (880MHz, Duel-Core)
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB (Winbond W25Q128BV)
- WiFi: MediaTek MT7615E (2.4GHz, 5GHz)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated)
- USB: USB 3.0 x1
- UART: [3.3V, TX, RX, GND] (57600 8N1)
Installation via web interface:
1. Flash initramfs image using OEM's Firmware Update page.
2. Connect to OpenWrt with an SSH connection to `192.168.1.1`.
3. Perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Flash stock firmware via OEM's Recovery mode
How to use OEM's Recovery mode:
1. Power on the device and connect the shell through UART.
2. Connect to the shell and press the `t` key on the keyboard.
3. Set fixed IP with `192.168.0.2` with subnet mask `255.255.255.0`
4. Flash image via TFTP to `192.168.0.1`
Additional Notes:
1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz.
2. If the 5Ghz frequency is too high, 5Ghz may not work.
3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi).
Signed-off-by: SeongUk Moon <antegral@antegral.net>
[convert CRLF to LF]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-14 12:54:05 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iptime_a6004ns-m
|
|
|
|
|
|
2019-11-11 16:25:31 +00:00
|
|
|
define Device/iptime_a6ns-m
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-11-11 16:25:31 +00:00
|
|
|
IMAGE_SIZE := 16128k
|
|
|
|
|
UIMAGE_NAME := a6nm
|
|
|
|
|
DEVICE_VENDOR := ipTIME
|
|
|
|
|
DEVICE_MODEL := A6ns-M
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-11-11 16:25:31 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iptime_a6ns-m
|
|
|
|
|
|
2019-10-06 20:06:31 +00:00
|
|
|
define Device/iptime_a8004t
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-10-06 20:06:31 +00:00
|
|
|
IMAGE_SIZE := 16128k
|
|
|
|
|
UIMAGE_NAME := a8004t
|
|
|
|
|
DEVICE_VENDOR := ipTIME
|
|
|
|
|
DEVICE_MODEL := A8004T
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 -uboot-envtools
|
2019-10-06 20:06:31 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iptime_a8004t
|
|
|
|
|
|
2022-01-29 14:25:32 +00:00
|
|
|
define Device/iptime_ax2004m
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-01-29 14:25:32 +00:00
|
|
|
IMAGE_SIZE := 121344k
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
IMAGES += recovery.bin
|
|
|
|
|
IMAGE/recovery.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
|
|
|
check-size | iptime-crc32 ax2004m
|
|
|
|
|
DEVICE_VENDOR := ipTIME
|
|
|
|
|
DEVICE_MODEL := AX2004M
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware kmod-usb3 -uboot-envtools
|
2022-01-29 14:25:32 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iptime_ax2004m
|
|
|
|
|
|
2021-08-01 15:43:34 +00:00
|
|
|
define Device/iptime_t5004
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2021-08-01 15:43:34 +00:00
|
|
|
IMAGE_SIZE := 129280k
|
|
|
|
|
UIMAGE_NAME := t5004
|
|
|
|
|
DEVICE_VENDOR := ipTIME
|
|
|
|
|
DEVICE_MODEL := T5004
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := -wpad-basic-mbedtls -uboot-envtools
|
2021-08-01 15:43:34 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += iptime_t5004
|
|
|
|
|
|
2019-12-13 16:24:19 +00:00
|
|
|
define Device/jcg_jhr-ac876m
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-12-13 16:24:19 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
IMAGES += factory.bin
|
2020-05-08 16:21:06 +00:00
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 89.1
|
2019-12-13 16:24:19 +00:00
|
|
|
JCG_MAXSIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := JCG
|
|
|
|
|
DEVICE_MODEL := JHR-AC876M
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-12-13 16:24:19 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += jcg_jhr-ac876m
|
|
|
|
|
|
2021-05-16 12:10:05 +00:00
|
|
|
define Device/jcg_q20
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-10-07 15:08:56 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2021-05-16 12:10:05 +00:00
|
|
|
IMAGE_SIZE := 91136k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
|
|
|
check-size
|
|
|
|
|
DEVICE_VENDOR := JCG
|
|
|
|
|
DEVICE_MODEL := Q20
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
2021-05-16 12:10:05 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += jcg_q20
|
|
|
|
|
|
2021-02-08 08:28:10 +00:00
|
|
|
define Device/jcg_y2
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | check-size | jcg-header 95.1
|
|
|
|
|
JCG_MAXSIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := JCG
|
|
|
|
|
DEVICE_MODEL := Y2
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 -uboot-envtools
|
2021-02-08 08:28:10 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += jcg_y2
|
|
|
|
|
|
2022-11-11 09:52:38 +00:00
|
|
|
define Device/keenetic_kn-3010
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 31488k
|
|
|
|
|
DEVICE_VENDOR := Keenetic
|
|
|
|
|
DEVICE_MODEL := KN-3010
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
2022-11-11 09:52:38 +00:00
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | pad-to $$$$(BLOCKSIZE) | \
|
2023-01-20 13:09:09 +00:00
|
|
|
check-size | zyimage -d 0x803010 -v "KN-3010"
|
2022-11-11 09:52:38 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += keenetic_kn-3010
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/lenovo_newifi-d1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-18 06:19:38 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
2023-04-18 13:42:41 +00:00
|
|
|
DEVICE_VENDOR := Lenovo
|
|
|
|
|
DEVICE_MODEL := Newifi D1
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += newifi-d1
|
2019-06-25 15:32:20 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += lenovo_newifi-d1
|
2019-06-25 15:32:20 +00:00
|
|
|
|
2021-03-02 05:10:14 +00:00
|
|
|
define Device/linksys_e5600
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2021-03-02 05:10:14 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 26624k
|
|
|
|
|
DEVICE_VENDOR := Linksys
|
|
|
|
|
DEVICE_MODEL := E5600
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap
|
2021-03-02 05:10:14 +00:00
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
|
|
|
append-ubi | check-size | gemtek-trailer
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_e5600
|
|
|
|
|
|
2021-03-22 21:06:14 +00:00
|
|
|
define Device/linksys_e7350
|
|
|
|
|
$(Device/belkin_rt1800)
|
|
|
|
|
DEVICE_VENDOR := Linksys
|
|
|
|
|
DEVICE_MODEL := E7350
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
|
|
|
append-ubi | check-size | belkin-header GOLF 1 9.9.9
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_e7350
|
|
|
|
|
|
2020-07-16 00:24:43 +00:00
|
|
|
define Device/linksys_ea7xxx
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: add support for Linksys EA7500 v2
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH: 5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615N (4x4:4)
- 5GHz: 1x MT7615N (4x4:4)
- 4 antennas: 3 external detachable antennas and 1 internal
USB:
- 1x USB 3.0
- 1x USB 2.0
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x White led (Power)
- 6x Green leds (link lan1-lan4, link wan, wps)
- 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)
Everything works correctly.
Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.
However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).
After this, you should be back in the OEM firmware.
Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).
When the router reboots flash the “factory” OpenWrt image and this
time it should work.
After the OpenWrt installation you have to use the sysupgrade image
for future updates.
Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.
Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
1) "kernel" and "rootfs"
2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.
This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.
A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.
Another way to switch the boot partition is:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.
Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.
However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.
If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
2020-05-11 23:27:50 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 36864k
|
|
|
|
|
DEVICE_VENDOR := Linksys
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt7615-firmware
|
ramips: add support for Linksys EA7500 v2
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH: 5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615N (4x4:4)
- 5GHz: 1x MT7615N (4x4:4)
- 4 antennas: 3 external detachable antennas and 1 internal
USB:
- 1x USB 3.0
- 1x USB 2.0
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x White led (Power)
- 6x Green leds (link lan1-lan4, link wan, wps)
- 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)
Everything works correctly.
Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.
However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).
After this, you should be back in the OEM firmware.
Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).
When the router reboots flash the “factory” OpenWrt image and this
time it should work.
After the OpenWrt installation you have to use the sysupgrade image
for future updates.
Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.
Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
1) "kernel" and "rootfs"
2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.
This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.
A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.
Another way to switch the boot partition is:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.
Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.
However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.
If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
2020-05-11 23:27:50 +00:00
|
|
|
IMAGES := sysupgrade.bin factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
2020-07-16 00:24:43 +00:00
|
|
|
append-ubi | check-size | linksys-image type=$$$$(LINKSYS_HWNAME)
|
|
|
|
|
endef
|
|
|
|
|
|
2021-12-10 13:23:01 +00:00
|
|
|
define Device/linksys_ea6350-v4
|
2022-01-13 20:56:37 +00:00
|
|
|
$(Device/linksys_ea7xxx)
|
|
|
|
|
DEVICE_MODEL := EA6350
|
|
|
|
|
DEVICE_VARIANT := v4
|
|
|
|
|
LINKSYS_HWNAME := EA6350
|
|
|
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7663-firmware-ap
|
2021-12-10 13:23:01 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_ea6350-v4
|
|
|
|
|
|
2020-07-16 00:24:43 +00:00
|
|
|
define Device/linksys_ea7300-v1
|
|
|
|
|
$(Device/linksys_ea7xxx)
|
|
|
|
|
DEVICE_MODEL := EA7300
|
|
|
|
|
DEVICE_VARIANT := v1
|
|
|
|
|
LINKSYS_HWNAME := EA7300
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_ea7300-v1
|
|
|
|
|
|
2020-09-23 02:30:45 +00:00
|
|
|
define Device/linksys_ea7300-v2
|
|
|
|
|
$(Device/linksys_ea7xxx)
|
|
|
|
|
DEVICE_MODEL := EA7300
|
|
|
|
|
DEVICE_VARIANT := v2
|
|
|
|
|
LINKSYS_HWNAME := EA7300v2
|
|
|
|
|
DEVICE_PACKAGES += kmod-mt7603
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_ea7300-v2
|
|
|
|
|
|
2020-07-16 00:24:43 +00:00
|
|
|
define Device/linksys_ea7500-v2
|
|
|
|
|
$(Device/linksys_ea7xxx)
|
|
|
|
|
DEVICE_MODEL := EA7500
|
|
|
|
|
DEVICE_VARIANT := v2
|
|
|
|
|
LINKSYS_HWNAME := EA7500v2
|
ramips: add support for Linksys EA7500 v2
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH: 5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615N (4x4:4)
- 5GHz: 1x MT7615N (4x4:4)
- 4 antennas: 3 external detachable antennas and 1 internal
USB:
- 1x USB 3.0
- 1x USB 2.0
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x White led (Power)
- 6x Green leds (link lan1-lan4, link wan, wps)
- 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)
Everything works correctly.
Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.
However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).
After this, you should be back in the OEM firmware.
Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).
When the router reboots flash the “factory” OpenWrt image and this
time it should work.
After the OpenWrt installation you have to use the sysupgrade image
for future updates.
Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.
Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
1) "kernel" and "rootfs"
2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.
This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.
A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.
Another way to switch the boot partition is:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.
Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.
However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.
If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
2020-05-11 23:27:50 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_ea7500-v2
|
|
|
|
|
|
2021-05-17 19:46:36 +00:00
|
|
|
define Device/linksys_ea8100-v1
|
|
|
|
|
$(Device/linksys_ea7xxx)
|
|
|
|
|
DEVICE_MODEL := EA8100
|
|
|
|
|
DEVICE_VARIANT := v1
|
|
|
|
|
LINKSYS_HWNAME := EA8100
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_ea8100-v1
|
|
|
|
|
|
2021-07-05 17:19:08 +00:00
|
|
|
define Device/linksys_ea8100-v2
|
|
|
|
|
$(Device/linksys_ea7xxx)
|
|
|
|
|
DEVICE_MODEL := EA8100
|
|
|
|
|
DEVICE_VARIANT := v2
|
|
|
|
|
LINKSYS_HWNAME := EA8100v2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_ea8100-v2
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/linksys_re6500
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2022-09-25 20:53:52 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 7872k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := Linksys
|
|
|
|
|
DEVICE_MODEL := RE6500
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += re6500
|
ramips: add support for Xiaomi Mi Router 3 Pro
Hardware:
CPU: MediaTek MT7621AT (2x880MHz)
RAM: 512MB DDR3
FLASH: 256MB NAND
WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!)
USB: 1x 3.0
ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000
LED: Power/Status
BTN: RESET
UART: 115200 8n1
Partition layout and boot:
Stock Xiaomi firmware has the MTD split into (among others)
- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)
Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.
Note uboot's tftp flash install writes the transferred
image to both kernel partitions.
Installation:
Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.
The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:
nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot
Reverting to stock:
The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.
For this we do the following:
fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot
After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.
Issues:
OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.
See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
2019-03-05 08:41:37 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += linksys_re6500
|
ramips: add support for Xiaomi Mi Router 3 Pro
Hardware:
CPU: MediaTek MT7621AT (2x880MHz)
RAM: 512MB DDR3
FLASH: 256MB NAND
WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!)
USB: 1x 3.0
ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000
LED: Power/Status
BTN: RESET
UART: 115200 8n1
Partition layout and boot:
Stock Xiaomi firmware has the MTD split into (among others)
- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)
Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.
Note uboot's tftp flash install writes the transferred
image to both kernel partitions.
Installation:
Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.
The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:
nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot
Reverting to stock:
The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.
For this we do the following:
fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot
After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.
Issues:
OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.
See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
2019-03-05 08:41:37 +00:00
|
|
|
|
2023-03-12 09:40:45 +00:00
|
|
|
define Device/linksys_re7000
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := Linksys
|
|
|
|
|
DEVICE_MODEL := RE7000
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_re7000
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/mediatek_ap-mt7621a-v60
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 7872k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := Mediatek
|
|
|
|
|
DEVICE_MODEL := AP-MT7621A-V60 EVB
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-sdhci-mt7620 kmod-sound-mt7620 \
|
|
|
|
|
-wpad-basic-mbedtls -uboot-envtools
|
2017-08-12 14:56:11 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += mediatek_ap-mt7621a-v60
|
2017-08-12 14:56:11 +00:00
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/mediatek_mt7621-eval-board
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-15 12:55:24 +00:00
|
|
|
IMAGE_SIZE := 15104k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := MediaTek
|
|
|
|
|
DEVICE_MODEL := MT7621 EVB
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := -wpad-basic-mbedtls -uboot-envtools
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += mt7621
|
2016-11-19 17:27:22 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += mediatek_mt7621-eval-board
|
2016-11-19 17:27:22 +00:00
|
|
|
|
2023-10-24 17:05:28 +00:00
|
|
|
define Device/meig_slt866
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 15104k
|
|
|
|
|
DEVICE_VENDOR := MeiG
|
|
|
|
|
DEVICE_MODEL := SLT866
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
kmod-usb-net-qmi-wwan kmod-usb-serial-option kmod-usb3 \
|
|
|
|
|
kmod-usb-net-rndis
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += meig_slt866
|
|
|
|
|
|
2023-03-23 22:53:47 +00:00
|
|
|
define Device/mercusys_mr70x-v1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
2023-10-29 14:51:32 +00:00
|
|
|
DEVICE_VENDOR := MERCUSYS
|
2023-03-23 22:53:47 +00:00
|
|
|
DEVICE_MODEL := MR70X
|
|
|
|
|
DEVICE_VARIANT := v1
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
|
|
|
|
TPLINK_BOARD_ID := MR70X
|
|
|
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
|
|
|
IMAGE_SIZE := 15744k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += mercusys_mr70x-v1
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/MikroTik
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := MikroTik
|
|
|
|
|
IMAGE_SIZE := 16128k
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 -uboot-envtools
|
2020-10-15 09:27:55 +00:00
|
|
|
KERNEL_NAME := vmlinuz
|
|
|
|
|
KERNEL := kernel-bin | append-dtb-elf
|
2019-12-19 18:40:33 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 | \
|
2021-06-20 16:54:36 +00:00
|
|
|
pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | \
|
|
|
|
|
append-metadata
|
2016-09-27 06:25:04 +00:00
|
|
|
endef
|
|
|
|
|
|
2022-08-06 13:35:15 +00:00
|
|
|
define Device/mikrotik_ltap-2hnd
|
|
|
|
|
$(Device/MikroTik)
|
|
|
|
|
DEVICE_MODEL := LtAP-2HnD
|
|
|
|
|
DEVICE_PACKAGES += kmod-ath9k kmod-pps-gpio rssileds
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += mikrotik_ltap-2hnd
|
|
|
|
|
|
2020-04-07 08:34:33 +00:00
|
|
|
define Device/mikrotik_routerboard-750gr3
|
2019-07-07 14:27:51 +00:00
|
|
|
$(Device/MikroTik)
|
2020-04-07 08:34:33 +00:00
|
|
|
DEVICE_MODEL := RouterBOARD 750Gr3
|
2022-12-28 04:44:11 +00:00
|
|
|
DEVICE_PACKAGES += -wpad-basic-mbedtls
|
2020-04-07 08:34:33 +00:00
|
|
|
SUPPORTED_DEVICES += mikrotik,rb750gr3
|
2019-07-07 14:27:51 +00:00
|
|
|
endef
|
2020-04-07 08:34:33 +00:00
|
|
|
TARGET_DEVICES += mikrotik_routerboard-750gr3
|
2019-07-07 14:27:51 +00:00
|
|
|
|
2020-06-10 22:15:40 +00:00
|
|
|
define Device/mikrotik_routerboard-760igs
|
|
|
|
|
$(Device/MikroTik)
|
|
|
|
|
DEVICE_MODEL := RouterBOARD 760iGS
|
2022-12-28 04:44:11 +00:00
|
|
|
DEVICE_PACKAGES += kmod-sfp -wpad-basic-mbedtls
|
2020-06-10 22:15:40 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += mikrotik_routerboard-760igs
|
|
|
|
|
|
2020-04-07 08:34:33 +00:00
|
|
|
define Device/mikrotik_routerboard-m11g
|
2019-07-07 14:27:51 +00:00
|
|
|
$(Device/MikroTik)
|
|
|
|
|
DEVICE_MODEL := RouterBOARD M11G
|
2022-12-28 04:44:11 +00:00
|
|
|
DEVICE_PACKAGES := -wpad-basic-mbedtls
|
2020-04-07 08:34:33 +00:00
|
|
|
SUPPORTED_DEVICES += mikrotik,rbm11g
|
2019-07-07 14:27:51 +00:00
|
|
|
endef
|
2020-04-07 08:34:33 +00:00
|
|
|
TARGET_DEVICES += mikrotik_routerboard-m11g
|
2019-07-07 14:27:51 +00:00
|
|
|
|
2020-04-07 08:34:33 +00:00
|
|
|
define Device/mikrotik_routerboard-m33g
|
2019-07-07 14:27:51 +00:00
|
|
|
$(Device/MikroTik)
|
|
|
|
|
DEVICE_MODEL := RouterBOARD M33G
|
2022-12-28 04:44:11 +00:00
|
|
|
DEVICE_PACKAGES := -wpad-basic-mbedtls
|
2020-04-07 08:34:33 +00:00
|
|
|
SUPPORTED_DEVICES += mikrotik,rbm33g
|
2019-07-07 14:27:51 +00:00
|
|
|
endef
|
2020-04-07 08:34:33 +00:00
|
|
|
TARGET_DEVICES += mikrotik_routerboard-m33g
|
2019-07-07 14:27:51 +00:00
|
|
|
|
2019-07-10 15:57:36 +00:00
|
|
|
define Device/mqmaker_witi
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2021-03-19 11:18:02 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := MQmaker
|
|
|
|
|
DEVICE_MODEL := WiTi
|
2020-03-05 13:57:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt76x2 kmod-sdhci-mt7620 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-10 15:57:36 +00:00
|
|
|
SUPPORTED_DEVICES += witi mqmaker,witi-256m mqmaker,witi-512m
|
ramips: add support for newifi d2
Previously Newifi D2 could only use PandoraBox M1's firmware.
It works fine, but LED GPIO is different.
As a result, a separated DTS file for this device should be implemented.
Hardware spec:
* CPU: MTK MT7621A
* RAM: 512MB
* ROM: 32MB SPI Flash
* WiFi: MTK MT7603+MT7612
* Button: 2 buttons (reset, wps)
* LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) &
2 dual-color LEDs (Power, Internet)
* Ethernet: 5 ports, 4 LAN + 1 WAN
Installation method:
Same as Newifi D1, users may need to request unlock code from the device
manufacturer. Otherwise, a SPI flash programmer may be necessary to get
the firmware flashed. After the device is unlocked, press and hold reset
button before power cable plugs in. Then go to http://192.168.1.1 to
upload and flash the firmware package.
Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
2017-12-15 03:51:33 +00:00
|
|
|
endef
|
2019-07-10 15:57:36 +00:00
|
|
|
TARGET_DEVICES += mqmaker_witi
|
2016-04-01 07:11:48 +00:00
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/mtc_wr1201
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2021-03-20 19:15:14 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-07 14:27:51 +00:00
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
|
DEVICE_VENDOR := MTC
|
|
|
|
|
DEVICE_MODEL := Wireless Router WR1201
|
2020-11-26 08:01:26 +00:00
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma -n 'WR1201_8_128'
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2017-03-11 07:44:33 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += mtc_wr1201
|
2017-03-11 07:44:33 +00:00
|
|
|
|
2022-05-04 15:16:38 +00:00
|
|
|
define Device/mts_wg430223
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-05-04 15:16:38 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := MTS
|
|
|
|
|
DEVICE_MODEL := WG430223
|
|
|
|
|
IMAGE_SIZE := 32768k
|
|
|
|
|
KERNEL_SIZE := 4352k
|
|
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
|
|
|
uImage none | arcadyan-trx 0x53485231 | pad-to $$(KERNEL_SIZE)
|
|
|
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
|
|
|
uImage none
|
|
|
|
|
IMAGES += factory.trx
|
|
|
|
|
IMAGE/factory.trx := append-kernel | append-ubi | check-size
|
2023-02-17 11:12:40 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware uencrypt-mbedtls
|
2022-05-04 15:16:38 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += mts_wg430223
|
|
|
|
|
|
2023-03-30 22:28:23 +00:00
|
|
|
define Device/netgear_eax12
|
|
|
|
|
$(Device/nand)
|
|
|
|
|
DEVICE_VENDOR := NETGEAR
|
|
|
|
|
DEVICE_MODEL := EAX12
|
|
|
|
|
DEVICE_ALT0_VENDOR := NETGEAR
|
|
|
|
|
DEVICE_ALT0_MODEL := EAX11
|
|
|
|
|
DEVICE_ALT0_VARIANT := v2
|
|
|
|
|
DEVICE_ALT1_VENDOR := NETGEAR
|
|
|
|
|
DEVICE_ALT1_MODEL := EAX15
|
|
|
|
|
DEVICE_ALT1_VARIANT := v2
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
|
|
|
|
NETGEAR_ENC_MODEL := EAX12
|
|
|
|
|
NETGEAR_ENC_REGION := US
|
|
|
|
|
NETGEAR_ENC_HW_ID_LIST := 1010000004540000_NETGEAR
|
|
|
|
|
NETGEAR_ENC_MODEL_LIST := EAX12;EAX11v2;EAX15v2
|
|
|
|
|
IMAGE_SIZE := 57344k
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
|
|
|
|
append-squashfs4-fakeroot
|
|
|
|
|
IMAGES += factory.img
|
|
|
|
|
IMAGE/factory.img := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
|
|
|
|
append-ubi | check-size | netgear-encrypted-factory
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_eax12
|
|
|
|
|
|
2019-03-21 14:55:09 +00:00
|
|
|
define Device/netgear_ex6150
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2022-10-18 06:55:46 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := NETGEAR
|
|
|
|
|
DEVICE_MODEL := EX6150
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 -uboot-envtools
|
2019-03-21 14:55:09 +00:00
|
|
|
NETGEAR_BOARD_ID := U12H318T00_NETGEAR
|
|
|
|
|
IMAGE_SIZE := 14848k
|
|
|
|
|
IMAGES += factory.chk
|
2020-05-08 16:21:06 +00:00
|
|
|
IMAGE/factory.chk := $$(sysupgrade_bin) | check-size | netgear-chk
|
2019-03-21 14:55:09 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_ex6150
|
|
|
|
|
|
2019-10-21 12:43:21 +00:00
|
|
|
define Device/netgear_sercomm_nand
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2020-04-15 01:32:02 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-08-27 21:55:12 +00:00
|
|
|
IMAGES += factory.img kernel.bin rootfs.bin
|
2019-12-19 18:40:33 +00:00
|
|
|
IMAGE/factory.img := pad-extra 2048k | append-kernel | pad-to 6144k | \
|
|
|
|
|
append-ubi | pad-to $$$$(BLOCKSIZE) | sercom-footer | pad-to 128 | \
|
2019-10-21 12:43:21 +00:00
|
|
|
zip $$$$(SERCOMM_HWNAME).bin | sercom-seal
|
2018-08-24 01:36:13 +00:00
|
|
|
IMAGE/kernel.bin := append-kernel
|
2020-03-10 13:58:27 +00:00
|
|
|
IMAGE/rootfs.bin := append-ubi | check-size
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := NETGEAR
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 kmod-usb-ledtrig-usbport \
|
|
|
|
|
-uboot-envtools
|
2019-10-21 12:43:21 +00:00
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/netgear_r6220
|
|
|
|
|
$(Device/netgear_sercomm_nand)
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_MODEL := R6220
|
2019-10-21 12:43:21 +00:00
|
|
|
SERCOMM_HWNAME := R6220
|
|
|
|
|
SERCOMM_HWID := AYA
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x0086
|
|
|
|
|
IMAGE_SIZE := 28672k
|
|
|
|
|
DEVICE_PACKAGES += kmod-mt76x2
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += r6220
|
2018-08-24 01:36:13 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += netgear_r6220
|
2018-08-24 01:36:13 +00:00
|
|
|
|
2019-08-29 08:08:38 +00:00
|
|
|
|
|
|
|
|
define Device/netgear_r6260
|
2019-10-21 12:43:21 +00:00
|
|
|
$(Device/netgear_sercomm_nand)
|
2019-08-29 08:08:38 +00:00
|
|
|
DEVICE_MODEL := R6260
|
2019-10-21 12:43:21 +00:00
|
|
|
SERCOMM_HWNAME := R6260
|
|
|
|
|
SERCOMM_HWID := CHJ
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x0052
|
|
|
|
|
IMAGE_SIZE := 40960k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
2019-08-29 08:08:38 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_r6260
|
|
|
|
|
|
|
|
|
|
define Device/netgear_r6350
|
2019-10-21 12:43:21 +00:00
|
|
|
$(Device/netgear_sercomm_nand)
|
2019-08-29 08:08:38 +00:00
|
|
|
DEVICE_MODEL := R6350
|
2019-10-21 12:43:21 +00:00
|
|
|
SERCOMM_HWNAME := R6350
|
|
|
|
|
SERCOMM_HWID := CHJ
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x0052
|
|
|
|
|
IMAGE_SIZE := 40960k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
2019-08-29 08:08:38 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += netgear_r6350
|
2018-06-25 20:51:43 +00:00
|
|
|
|
ramips: add support for NETGEAR R6700v2/AC2400
SoC: MediaTek MT7621AT
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7615N an+ac
MediaTek MT7615N bgn
ETH: MediaTek MT7621AT
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white),
USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white),
WPS Button(white)
Installation:
Login to netgear webinterface and flash factory.img
Based on a discontinued GitHub Pull Request by
kuyokushin <codenamezero@protonmail.com>
https://github.com/openwrt/openwrt/pull/2545
NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk
AC2400, Nighthawk AC2100 and already added R6800. Rest of them should
be really easy supportable. Image for R6700v2 should work perfectly with
them. Please refer:
https://github.com/openwrt/openwrt/pull/2614
Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2]
Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[add guest led to mt7621_netgear_r6700-v2.dts end edit commit message]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-12-27 18:05:06 +00:00
|
|
|
define Device/netgear_r6700-v2
|
|
|
|
|
$(Device/netgear_sercomm_nand)
|
|
|
|
|
DEVICE_MODEL := R6700
|
|
|
|
|
DEVICE_VARIANT := v2
|
|
|
|
|
DEVICE_ALT0_VENDOR := NETGEAR
|
|
|
|
|
DEVICE_ALT0_MODEL := Nighthawk AC2400
|
2020-04-15 13:43:51 +00:00
|
|
|
DEVICE_ALT0_VARIANT := v1
|
2021-08-21 07:10:22 +00:00
|
|
|
DEVICE_ALT1_VENDOR := NETGEAR
|
|
|
|
|
DEVICE_ALT1_MODEL := Nighthawk AC2100
|
|
|
|
|
DEVICE_ALT1_VARIANT := v1
|
ramips: add support for NETGEAR R6700v2/AC2400
SoC: MediaTek MT7621AT
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7615N an+ac
MediaTek MT7615N bgn
ETH: MediaTek MT7621AT
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white),
USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white),
WPS Button(white)
Installation:
Login to netgear webinterface and flash factory.img
Based on a discontinued GitHub Pull Request by
kuyokushin <codenamezero@protonmail.com>
https://github.com/openwrt/openwrt/pull/2545
NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk
AC2400, Nighthawk AC2100 and already added R6800. Rest of them should
be really easy supportable. Image for R6700v2 should work perfectly with
them. Please refer:
https://github.com/openwrt/openwrt/pull/2614
Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2]
Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[add guest led to mt7621_netgear_r6700-v2.dts end edit commit message]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-12-27 18:05:06 +00:00
|
|
|
SERCOMM_HWNAME := R6950
|
|
|
|
|
SERCOMM_HWID := BZV
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x1032
|
|
|
|
|
IMAGE_SIZE := 40960k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
ramips: add support for NETGEAR R6700v2/AC2400
SoC: MediaTek MT7621AT
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7615N an+ac
MediaTek MT7615N bgn
ETH: MediaTek MT7621AT
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white),
USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white),
WPS Button(white)
Installation:
Login to netgear webinterface and flash factory.img
Based on a discontinued GitHub Pull Request by
kuyokushin <codenamezero@protonmail.com>
https://github.com/openwrt/openwrt/pull/2545
NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk
AC2400, Nighthawk AC2100 and already added R6800. Rest of them should
be really easy supportable. Image for R6700v2 should work perfectly with
them. Please refer:
https://github.com/openwrt/openwrt/pull/2614
Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2]
Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[add guest led to mt7621_netgear_r6700-v2.dts end edit commit message]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-12-27 18:05:06 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_r6700-v2
|
|
|
|
|
|
2019-12-11 20:54:24 +00:00
|
|
|
define Device/netgear_r6800
|
|
|
|
|
$(Device/netgear_sercomm_nand)
|
|
|
|
|
DEVICE_MODEL := R6800
|
|
|
|
|
SERCOMM_HWNAME := R6950
|
|
|
|
|
SERCOMM_HWID := BZV
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x0062
|
|
|
|
|
IMAGE_SIZE := 40960k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
2019-12-11 20:54:24 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_r6800
|
|
|
|
|
|
2019-08-29 08:08:38 +00:00
|
|
|
define Device/netgear_r6850
|
2019-10-21 12:43:21 +00:00
|
|
|
$(Device/netgear_sercomm_nand)
|
2019-08-29 08:08:38 +00:00
|
|
|
DEVICE_MODEL := R6850
|
2019-10-21 12:43:21 +00:00
|
|
|
SERCOMM_HWNAME := R6850
|
|
|
|
|
SERCOMM_HWID := CHJ
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x0052
|
|
|
|
|
IMAGE_SIZE := 40960k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
2019-08-29 08:08:38 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_r6850
|
|
|
|
|
|
2021-09-26 04:07:58 +00:00
|
|
|
define Device/netgear_r6900-v2
|
|
|
|
|
$(Device/netgear_sercomm_nand)
|
|
|
|
|
DEVICE_MODEL := R6900
|
|
|
|
|
DEVICE_VARIANT := v2
|
|
|
|
|
SERCOMM_HWNAME := R6950
|
|
|
|
|
SERCOMM_HWID := BZV
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x1032
|
|
|
|
|
IMAGE_SIZE := 40960k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
2021-09-26 04:07:58 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_r6900-v2
|
|
|
|
|
|
2021-08-21 05:36:50 +00:00
|
|
|
define Device/netgear_r7200
|
|
|
|
|
$(Device/netgear_sercomm_nand)
|
|
|
|
|
DEVICE_MODEL := R7200
|
|
|
|
|
SERCOMM_HWNAME := R6950
|
|
|
|
|
SERCOMM_HWID := BZV
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x1032
|
|
|
|
|
IMAGE_SIZE := 40960k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
2021-08-21 05:36:50 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_r7200
|
|
|
|
|
|
2021-09-26 04:08:06 +00:00
|
|
|
define Device/netgear_r7450
|
|
|
|
|
$(Device/netgear_sercomm_nand)
|
|
|
|
|
DEVICE_MODEL := R7450
|
|
|
|
|
SERCOMM_HWNAME := R6950
|
|
|
|
|
SERCOMM_HWID := BZV
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x1032
|
|
|
|
|
IMAGE_SIZE := 40960k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
2021-09-26 04:08:06 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_r7450
|
|
|
|
|
|
2020-06-09 13:16:35 +00:00
|
|
|
define Device/netgear_wac104
|
|
|
|
|
$(Device/netgear_sercomm_nand)
|
|
|
|
|
DEVICE_MODEL := WAC104
|
|
|
|
|
SERCOMM_HWNAME := WAC104
|
|
|
|
|
SERCOMM_HWID := CAY
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x0006
|
|
|
|
|
IMAGE_SIZE := 28672k
|
|
|
|
|
DEVICE_PACKAGES += kmod-mt76x2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_wac104
|
|
|
|
|
|
2020-06-26 21:46:19 +00:00
|
|
|
define Device/netgear_wac124
|
|
|
|
|
$(Device/netgear_sercomm_nand)
|
|
|
|
|
DEVICE_MODEL := WAC124
|
|
|
|
|
SERCOMM_HWNAME := WAC124
|
|
|
|
|
SERCOMM_HWID := CTL
|
|
|
|
|
SERCOMM_HWVER := A003
|
|
|
|
|
SERCOMM_SWVER := 0x0402
|
|
|
|
|
IMAGE_SIZE := 40960k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7615-firmware
|
2020-06-26 21:46:19 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_wac124
|
|
|
|
|
|
2022-07-02 20:18:59 +00:00
|
|
|
define Device/netgear_wax202
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-07-02 20:18:59 +00:00
|
|
|
DEVICE_VENDOR := NETGEAR
|
|
|
|
|
DEVICE_MODEL := WAX202
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
2022-07-02 20:18:59 +00:00
|
|
|
NETGEAR_ENC_MODEL := WAX202
|
|
|
|
|
NETGEAR_ENC_REGION := US
|
|
|
|
|
IMAGE_SIZE := 38912k
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
|
|
|
|
append-squashfs4-fakeroot
|
|
|
|
|
IMAGES += factory.img
|
|
|
|
|
IMAGE/factory.img := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
|
|
|
|
append-ubi | check-size | netgear-encrypted-factory
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_wax202
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/netgear_wndr3700-v5
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-08-03 17:23:50 +00:00
|
|
|
$(Device/netgear_sercomm_nor)
|
2020-04-15 01:32:02 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-07 14:27:51 +00:00
|
|
|
IMAGE_SIZE := 15232k
|
2020-08-03 17:23:50 +00:00
|
|
|
DEVICE_MODEL := WNDR3700
|
|
|
|
|
DEVICE_VARIANT := v5
|
|
|
|
|
SERCOMM_HWNAME := WNDR3700v5
|
2019-07-07 14:27:51 +00:00
|
|
|
SERCOMM_HWID := AYB
|
|
|
|
|
SERCOMM_HWVER := A001
|
|
|
|
|
SERCOMM_SWVER := 0x1054
|
2020-08-03 17:23:50 +00:00
|
|
|
SERCOMM_PAD := 320k
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += wndr3700v5
|
2018-11-29 23:13:53 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += netgear_wndr3700-v5
|
2018-11-29 23:13:53 +00:00
|
|
|
|
2019-10-08 13:21:13 +00:00
|
|
|
define Device/netis_wf2881
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-11-21 02:37:36 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-07 14:27:51 +00:00
|
|
|
FILESYSTEMS := squashfs
|
|
|
|
|
IMAGE_SIZE := 129280k
|
2020-02-07 11:26:05 +00:00
|
|
|
UIMAGE_NAME := WF2881_0.0.00
|
2022-11-21 02:37:36 +00:00
|
|
|
KERNEL_INITRAMFS := $$(KERNEL) | netis-tail WF2881
|
2019-10-02 13:12:28 +00:00
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
2020-03-10 13:58:27 +00:00
|
|
|
check-size
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := NETIS
|
2019-10-08 13:21:13 +00:00
|
|
|
DEVICE_MODEL := WF2881
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport \
|
|
|
|
|
-uboot-envtools
|
2017-07-23 19:06:44 +00:00
|
|
|
endef
|
2019-10-08 13:21:13 +00:00
|
|
|
TARGET_DEVICES += netis_wf2881
|
2017-07-23 19:06:44 +00:00
|
|
|
|
ramips: add support for OrayBox X3A
OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621.
Specification:
* SoC: MT7621
* RAM: DDR3 128 MiB
* Flash: 16 MiB NOR (XM25Q128)
* Wi-Fi: (single chip hosting both 2.4G and 5G)
* 2.4GHz: MT7615
* 5GHz: MT7615
* Ethernet: 3x 1000Mbps
* Switch: MT7530
* LED:
* Ethernet LEDs: On the back of the router, hardware-controlled.
* Status LEDs: One "pixel-like" RGB LED in the front of the router,
which is actually made up of 3 individual LEDs (with
dedicated GPIO pins) with the color of Red, Green,
and Blue.
The OEM firmware only lights up one color at a time to
indicate status, but that's very boring, and the colors
actually look great when combined, so I've improvised a
little and made them indicate netdev activities.
My test results:
GPIO 13/14/15
000 white (actually more like bright green or cyan
because the brightness of the green LED is
higher than red and blue)
001 bright purple
010 bright green
011 red
100 bright cyan
101 blue
110 green
111 off
Flash Layout:
0x0000000-0x0030000 : "u-boot"
0x0030000-0x0040000 : "u-boot-env"
0x0040000-0x0050000 : "factory"
0x0050000-0x0f50000 : "firmware"
/*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/
0x0fe0000-0x0ff0000 : "bdinfo"
0x0ff0000-0x1000000 : "reserve"
MAC address:
MAC Source Description Fix
A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS
A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS
A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS
A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG
A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A
A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A
Stock dmesg:
https://pastebin.com/2t2jwLdf
Stock Dumps:
https://pastebin.com/LDLxSWX3
Installation via SSH (does not void your warranty):
1. -----UNLOCK SSH-----
1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in
your browser. Password is 'admin'.
1.2 Click the "备份且导出" (backup and export) button, and download the
config file.
1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'.
1.4 Edit the file './system'. Change the '0' into '1' under
"config sys 'ssh'".
1.5 Save the file.
1.6 Upload the file by clicking the "导入且恢复" (import and recover)
button. The router will automatically reboot.
2. -----FLASH THE OPENWRT FIRMWARE-----
2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/'
folder to your router. It should be root@10.168.1.1 and the password
is 'admin'.
2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'.
2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to
backup the stock firmware. Since the OEM does not provide firmware
download on their website, this is the only way to get it.
2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock
firmware from '/tmp/' to your local drive. Then you'd better use a hex
reading tool to have a rough look at it to make sure nothing is
corrupt. Or u can just back up again and cross check the MD5.
2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash
the firmware.
2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and
reboot the router.
Revert to stock firmware:
1. load stock firmware using mtd (make sure u have a backup).
Signed-off-by: Ray Wang <raywang777@foxmail.com>
2022-03-12 14:57:12 +00:00
|
|
|
define Device/oraybox_x3a
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 15360k
|
|
|
|
|
DEVICE_VENDOR := OrayBox
|
|
|
|
|
DEVICE_MODEL := X3A
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
ramips: add support for OrayBox X3A
OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621.
Specification:
* SoC: MT7621
* RAM: DDR3 128 MiB
* Flash: 16 MiB NOR (XM25Q128)
* Wi-Fi: (single chip hosting both 2.4G and 5G)
* 2.4GHz: MT7615
* 5GHz: MT7615
* Ethernet: 3x 1000Mbps
* Switch: MT7530
* LED:
* Ethernet LEDs: On the back of the router, hardware-controlled.
* Status LEDs: One "pixel-like" RGB LED in the front of the router,
which is actually made up of 3 individual LEDs (with
dedicated GPIO pins) with the color of Red, Green,
and Blue.
The OEM firmware only lights up one color at a time to
indicate status, but that's very boring, and the colors
actually look great when combined, so I've improvised a
little and made them indicate netdev activities.
My test results:
GPIO 13/14/15
000 white (actually more like bright green or cyan
because the brightness of the green LED is
higher than red and blue)
001 bright purple
010 bright green
011 red
100 bright cyan
101 blue
110 green
111 off
Flash Layout:
0x0000000-0x0030000 : "u-boot"
0x0030000-0x0040000 : "u-boot-env"
0x0040000-0x0050000 : "factory"
0x0050000-0x0f50000 : "firmware"
/*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/
0x0fe0000-0x0ff0000 : "bdinfo"
0x0ff0000-0x1000000 : "reserve"
MAC address:
MAC Source Description Fix
A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS
A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS
A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS
A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG
A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A
A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A
Stock dmesg:
https://pastebin.com/2t2jwLdf
Stock Dumps:
https://pastebin.com/LDLxSWX3
Installation via SSH (does not void your warranty):
1. -----UNLOCK SSH-----
1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in
your browser. Password is 'admin'.
1.2 Click the "备份且导出" (backup and export) button, and download the
config file.
1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'.
1.4 Edit the file './system'. Change the '0' into '1' under
"config sys 'ssh'".
1.5 Save the file.
1.6 Upload the file by clicking the "导入且恢复" (import and recover)
button. The router will automatically reboot.
2. -----FLASH THE OPENWRT FIRMWARE-----
2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/'
folder to your router. It should be root@10.168.1.1 and the password
is 'admin'.
2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'.
2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to
backup the stock firmware. Since the OEM does not provide firmware
download on their website, this is the only way to get it.
2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock
firmware from '/tmp/' to your local drive. Then you'd better use a hex
reading tool to have a rough look at it to make sure nothing is
corrupt. Or u can just back up again and cross check the MD5.
2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash
the firmware.
2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and
reboot the router.
Revert to stock firmware:
1. load stock firmware using mtd (make sure u have a backup).
Signed-off-by: Ray Wang <raywang777@foxmail.com>
2022-03-12 14:57:12 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += oraybox_x3a
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/phicomm_k2p
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-15 12:55:02 +00:00
|
|
|
IMAGE_SIZE := 15744k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := Phicomm
|
|
|
|
|
DEVICE_MODEL := K2P
|
2019-10-06 19:07:33 +00:00
|
|
|
DEVICE_ALT0_VENDOR := Phicomm
|
|
|
|
|
DEVICE_ALT0_MODEL := KE 2P
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += k2p
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2016-11-19 17:27:22 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += phicomm_k2p
|
2016-11-19 17:27:22 +00:00
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/planex_vr500
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-24 05:51:53 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-15 12:55:24 +00:00
|
|
|
IMAGE_SIZE := 65216k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := Planex
|
|
|
|
|
DEVICE_MODEL := VR500
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-mbedtls -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += vr500
|
2016-04-01 07:11:48 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += planex_vr500
|
2016-04-01 07:11:48 +00:00
|
|
|
|
ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.
Specifications:
- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
- Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
- Switch: 1 * POWER switch
MAC addresses as verified by vendor firmware:
use address source
LAN C8:XX:XX:3A:XX:E7 Config "protest_lan_mac" ascii (label)
WAN C8:XX:XX:3A:XX:EA Config "protest_wan_mac" ascii
5G C8:XX:XX:3A:XX:E8 Factory "0x4" hex
2.4G CA:XX:XX:4A:XX:E8 [not on flash]
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C8:XX:XX:90:XX:C3 CA:XX:XX:C0:XX:C3 0x30
C8:XX:XX:3A:XX:08 CA:XX:XX:4A:XX:08 0x10
C8:XX:XX:3A:XX:E8 CA:XX:XX:4A:XX:E8 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Notes:
1. The vendor firmware allows you to connect to the router by telnet.
(known version 1.0.0 can open telnet.)
There is no official binary firmware available.
Backup the important partitions data:
"Bootloader", "Config", "Factory", and "firmware".
Note that with the vendor firmware the memory is detected only 128MiB
and the last 512KiB in NAND flash is not used.
2. The POWER LED is default on after press POWER switch.
The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
The WPS LED is controlled by MT7615DN's GPIO.
Currently there is no proper way to configure it.
3. At the time of adding support the wireless config needs to be set up
by editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LuCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Flash instructions using initramfs image:
1. Press POWER switch to power down if the router is running.
2. Connect PC to one of LAN ports, and set
static IP address to "10.10.10.2", netmask to "255.255.255.0",
and gateway to "10.10.10.1" manually on the PC.
3. Push and hold the WIFI button, and then power up the router.
After about 10s (or you can call the recovery page, see "4" below)
you can release the WIFI button.
There is no clear indication when the router
is entering or has entered into "RAISECOM Router Recovery Mode".
4. Call the recovery page for the router at "http://10.10.10.1".
Keep an eye on the "WARNING!! tip" of the recovery page.
Click "Choose File" to select initramfs image, then click "Upload".
5. If image is uploaded successfully, you will see the page display
"Device is upgrading the firmware... %".
Keep an eye on the "WARNING!! tip" of the recovery page.
When the page display "Upgrade Successfully",
you can set IP address as "automatically obtain".
6. After the rebooting (PC should automatically obtain an IP address),
open the SSH connection, then download the sysupgrade image
to the router and perform sysupgrade with it.
Flash back to vendor firmware:
See "Flash instructions 1 - 5" above.
The only difference is that in step 4
you should select the vendor firmware which you backup.
Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2021-08-11 07:47:22 +00:00
|
|
|
define Device/raisecom_msg1500-x-00
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.
Specifications:
- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
- Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
- Switch: 1 * POWER switch
MAC addresses as verified by vendor firmware:
use address source
LAN C8:XX:XX:3A:XX:E7 Config "protest_lan_mac" ascii (label)
WAN C8:XX:XX:3A:XX:EA Config "protest_wan_mac" ascii
5G C8:XX:XX:3A:XX:E8 Factory "0x4" hex
2.4G CA:XX:XX:4A:XX:E8 [not on flash]
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C8:XX:XX:90:XX:C3 CA:XX:XX:C0:XX:C3 0x30
C8:XX:XX:3A:XX:08 CA:XX:XX:4A:XX:08 0x10
C8:XX:XX:3A:XX:E8 CA:XX:XX:4A:XX:E8 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Notes:
1. The vendor firmware allows you to connect to the router by telnet.
(known version 1.0.0 can open telnet.)
There is no official binary firmware available.
Backup the important partitions data:
"Bootloader", "Config", "Factory", and "firmware".
Note that with the vendor firmware the memory is detected only 128MiB
and the last 512KiB in NAND flash is not used.
2. The POWER LED is default on after press POWER switch.
The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
The WPS LED is controlled by MT7615DN's GPIO.
Currently there is no proper way to configure it.
3. At the time of adding support the wireless config needs to be set up
by editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LuCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Flash instructions using initramfs image:
1. Press POWER switch to power down if the router is running.
2. Connect PC to one of LAN ports, and set
static IP address to "10.10.10.2", netmask to "255.255.255.0",
and gateway to "10.10.10.1" manually on the PC.
3. Push and hold the WIFI button, and then power up the router.
After about 10s (or you can call the recovery page, see "4" below)
you can release the WIFI button.
There is no clear indication when the router
is entering or has entered into "RAISECOM Router Recovery Mode".
4. Call the recovery page for the router at "http://10.10.10.1".
Keep an eye on the "WARNING!! tip" of the recovery page.
Click "Choose File" to select initramfs image, then click "Upload".
5. If image is uploaded successfully, you will see the page display
"Device is upgrading the firmware... %".
Keep an eye on the "WARNING!! tip" of the recovery page.
When the page display "Upgrade Successfully",
you can set IP address as "automatically obtain".
6. After the rebooting (PC should automatically obtain an IP address),
open the SSH connection, then download the sysupgrade image
to the router and perform sysupgrade with it.
Flash back to vendor firmware:
See "Flash instructions 1 - 5" above.
The only difference is that in step 4
you should select the vendor firmware which you backup.
Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2021-08-11 07:47:22 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 129280k
|
|
|
|
|
DEVICE_VENDOR := RAISECOM
|
|
|
|
|
DEVICE_MODEL := MSG1500
|
|
|
|
|
DEVICE_VARIANT := X.00
|
2022-06-02 15:01:29 +00:00
|
|
|
DEVICE_ALT0_VENDOR := Nokia
|
|
|
|
|
DEVICE_ALT0_MODEL := A-040W-Q
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 kmod-usb-ledtrig-usbport
|
ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.
Specifications:
- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
- Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
- Switch: 1 * POWER switch
MAC addresses as verified by vendor firmware:
use address source
LAN C8:XX:XX:3A:XX:E7 Config "protest_lan_mac" ascii (label)
WAN C8:XX:XX:3A:XX:EA Config "protest_wan_mac" ascii
5G C8:XX:XX:3A:XX:E8 Factory "0x4" hex
2.4G CA:XX:XX:4A:XX:E8 [not on flash]
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C8:XX:XX:90:XX:C3 CA:XX:XX:C0:XX:C3 0x30
C8:XX:XX:3A:XX:08 CA:XX:XX:4A:XX:08 0x10
C8:XX:XX:3A:XX:E8 CA:XX:XX:4A:XX:E8 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Notes:
1. The vendor firmware allows you to connect to the router by telnet.
(known version 1.0.0 can open telnet.)
There is no official binary firmware available.
Backup the important partitions data:
"Bootloader", "Config", "Factory", and "firmware".
Note that with the vendor firmware the memory is detected only 128MiB
and the last 512KiB in NAND flash is not used.
2. The POWER LED is default on after press POWER switch.
The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
The WPS LED is controlled by MT7615DN's GPIO.
Currently there is no proper way to configure it.
3. At the time of adding support the wireless config needs to be set up
by editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LuCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Flash instructions using initramfs image:
1. Press POWER switch to power down if the router is running.
2. Connect PC to one of LAN ports, and set
static IP address to "10.10.10.2", netmask to "255.255.255.0",
and gateway to "10.10.10.1" manually on the PC.
3. Push and hold the WIFI button, and then power up the router.
After about 10s (or you can call the recovery page, see "4" below)
you can release the WIFI button.
There is no clear indication when the router
is entering or has entered into "RAISECOM Router Recovery Mode".
4. Call the recovery page for the router at "http://10.10.10.1".
Keep an eye on the "WARNING!! tip" of the recovery page.
Click "Choose File" to select initramfs image, then click "Upload".
5. If image is uploaded successfully, you will see the page display
"Device is upgrading the firmware... %".
Keep an eye on the "WARNING!! tip" of the recovery page.
When the page display "Upgrade Successfully",
you can set IP address as "automatically obtain".
6. After the rebooting (PC should automatically obtain an IP address),
open the SSH connection, then download the sysupgrade image
to the router and perform sysupgrade with it.
Flash back to vendor firmware:
See "Flash instructions 1 - 5" above.
The only difference is that in step 4
you should select the vendor firmware which you backup.
Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2021-08-11 07:47:22 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += raisecom_msg1500-x-00
|
|
|
|
|
|
2022-03-07 18:50:29 +00:00
|
|
|
define Device/renkforce_ws-wn530hp3-a
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Renkforce
|
|
|
|
|
DEVICE_MODEL := WS-WN530HP3-A
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
2022-03-07 18:50:29 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 65536 | append-rootfs | \
|
|
|
|
|
check-size | append-metadata
|
|
|
|
|
IMAGE_SIZE := 15040k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += renkforce_ws-wn530hp3-a
|
|
|
|
|
|
ramips: add support for Rostelecom RT-FE-1A
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Power (green, unmanaged)
- 1x Status (green, gpio)
- 1x 2.4G (green, hardware, mt76-phy0)
- 1x 2.4G (blue, gpio)
- 1x 5G (green, hardware, mt76-phy1)
- 1x 5G (blue, gpio)
- 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (default http://192.168.0.1/)
under "admin" account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following block:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>
5. Replace <some value> by a new superadmin password and add a line
which enabling superadmin login after. For example, the block after
the changes:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit f3cdc9f9881796794c06f784a2e4790f5ed75d1f)
2023-11-25 12:14:57 +00:00
|
|
|
define Device/rostelecom_rt-fe-1a
|
|
|
|
|
$(Device/sercomm_dxx)
|
|
|
|
|
IMAGE_SIZE := 24576k
|
|
|
|
|
SERCOMM_HWID := CX4
|
|
|
|
|
SERCOMM_HWVER := 11300
|
|
|
|
|
SERCOMM_SWVER := 2010
|
|
|
|
|
DEVICE_VENDOR := Rostelecom
|
|
|
|
|
DEVICE_MODEL := RT-FE-1A
|
|
|
|
|
DEVICE_ALT0_VENDOR := Sercomm
|
|
|
|
|
DEVICE_ALT0_MODEL := RT-FE-1A
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += rostelecom_rt-fe-1a
|
|
|
|
|
|
ramips: add support for Rostelecom RT-SF-1
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
firmware
6. Update firmware using web interface with the OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+------------+
| use | address | example |
+-----+------------+------------+
| LAN | label | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g | label + 2 | *:74, *:d4 |
| 5g | label + 3 | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-02 08:44:46 +00:00
|
|
|
define Device/rostelecom_rt-sf-1
|
|
|
|
|
$(Device/sercomm_dxx)
|
|
|
|
|
IMAGE_SIZE := 32768k
|
|
|
|
|
SERCOMM_HWID := DKG
|
|
|
|
|
SERCOMM_HWVER := 10110
|
|
|
|
|
SERCOMM_SWVER := 1026
|
|
|
|
|
DEVICE_VENDOR := Rostelecom
|
|
|
|
|
DEVICE_MODEL := RT-SF-1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware kmod-usb3
|
ramips: add support for Rostelecom RT-SF-1
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
firmware
6. Update firmware using web interface with the OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+------------+
| use | address | example |
+-----+------------+------------+
| LAN | label | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g | label + 2 | *:74, *:d4 |
| 5g | label + 3 | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-02 08:44:46 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += rostelecom_rt-sf-1
|
|
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/samknows_whitebox-v8
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2022-05-13 11:35:59 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := SamKnows
|
|
|
|
|
DEVICE_MODEL := Whitebox 8
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += sk-wb8
|
2016-11-19 17:27:22 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += samknows_whitebox-v8
|
2016-11-19 17:27:22 +00:00
|
|
|
|
2021-03-14 23:07:17 +00:00
|
|
|
define Device/sercomm_na502
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2023-11-08 12:50:55 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2021-03-14 23:07:17 +00:00
|
|
|
IMAGE_SIZE := 20480k
|
|
|
|
|
DEVICE_VENDOR := SERCOMM
|
|
|
|
|
DEVICE_MODEL := NA502
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-mt7603 kmod-usb3 -uboot-envtools
|
2021-03-14 23:07:17 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += sercomm_na502
|
|
|
|
|
|
2021-03-22 00:01:44 +00:00
|
|
|
define Device/sercomm_na502s
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2021-03-22 00:01:44 +00:00
|
|
|
IMAGE_SIZE := 20971520
|
|
|
|
|
DEVICE_VENDOR := SERCOMM
|
|
|
|
|
DEVICE_MODEL := NA502S
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-mt7603 kmod-usb3 kmod-usb-serial \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-serial-xr_usb_serial_common -uboot-envtools
|
2021-03-22 00:01:44 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += sercomm_na502s
|
|
|
|
|
|
2022-09-15 17:10:52 +00:00
|
|
|
define Device/sim_simax1800t
|
|
|
|
|
$(Device/haier-sim_wr1800k)
|
|
|
|
|
DEVICE_VENDOR := SIM
|
|
|
|
|
DEVICE_MODEL := SIMAX1800T
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += sim_simax1800t
|
|
|
|
|
|
2022-11-03 17:23:44 +00:00
|
|
|
define Device/snr_snr-cpe-me1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 15040k
|
|
|
|
|
DEVICE_VENDOR := SNR
|
|
|
|
|
DEVICE_MODEL := SNR-CPE-ME1
|
|
|
|
|
UIMAGE_NAME := SNR-CPE-ME1-5GHZ-MT
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x0e kmod-usb3 \
|
|
|
|
|
kmod-usb-ledtrig-usbport uboot-envtools
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += snr_snr-cpe-me1
|
|
|
|
|
|
2022-05-30 08:46:34 +00:00
|
|
|
define Device/snr_snr-cpe-me2-lite
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := SNR
|
|
|
|
|
DEVICE_MODEL := SNR-CPE-ME2-Lite
|
|
|
|
|
UIMAGE_NAME := $$(DEVICE_MODEL)
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
2022-05-30 08:46:34 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += snr_snr-cpe-me2-lite
|
|
|
|
|
|
2023-03-06 10:49:33 +00:00
|
|
|
define Device/snr_snr-cpe-me2-sfp
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := SNR
|
|
|
|
|
DEVICE_MODEL := SNR-CPE-ME2-SFP
|
|
|
|
|
UIMAGE_NAME := $$(DEVICE_MODEL)
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 \
|
|
|
|
|
kmod-sfp kmod-usb-ledtrig-usbport uboot-envtools
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += snr_snr-cpe-me2-sfp
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/storylink_sap-g3200u3
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 7872k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := STORYLiNK
|
|
|
|
|
DEVICE_MODEL := SAP-G3200U3
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport \
|
|
|
|
|
-uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += sap-g3200u3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += storylink_sap-g3200u3
|
|
|
|
|
|
2019-04-19 04:12:11 +00:00
|
|
|
define Device/telco-electronics_x1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-04-19 04:12:11 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := Telco Electronics
|
|
|
|
|
DEVICE_MODEL := X1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 kmod-mt76 -uboot-envtools
|
2019-04-19 04:12:11 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += telco-electronics_x1
|
|
|
|
|
|
2021-05-06 16:07:18 +00:00
|
|
|
define Device/tenbay_t-mb5eu-v01
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Tenbay
|
|
|
|
|
DEVICE_MODEL := T-MB5EU-V01
|
|
|
|
|
DEVICE_DTS_CONFIG := config@1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7915-firmware kmod-usb3 -uboot-envtools
|
2021-05-06 16:07:18 +00:00
|
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
|
SUPPORTED_DEVICES += mt7621-dm2-t-mb5eu-v01-nor
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tenbay_t-mb5eu-v01
|
|
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/thunder_timecloud
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-18 06:19:38 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := Thunder
|
|
|
|
|
DEVICE_MODEL := Timecloud
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb3 -wpad-basic-mbedtls -uboot-envtools
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += timecloud
|
2016-08-10 00:18:32 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += thunder_timecloud
|
2016-08-10 00:18:32 +00:00
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/totolink_a7000r
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-07 14:27:51 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
UIMAGE_NAME := C8340R1C-9999
|
|
|
|
|
DEVICE_VENDOR := TOTOLINK
|
|
|
|
|
DEVICE_MODEL := A7000R
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += totolink_a7000r
|
|
|
|
|
|
2020-10-21 05:11:35 +00:00
|
|
|
define Device/totolink_x5000r
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
UIMAGE_NAME := C8343R-9999
|
|
|
|
|
DEVICE_VENDOR := TOTOLINK
|
|
|
|
|
DEVICE_MODEL := X5000R
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
2020-10-21 05:11:35 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += totolink_x5000r
|
|
|
|
|
|
2023-03-29 10:11:30 +00:00
|
|
|
define Device/tozed_zlt-s12-pro
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := TOZED
|
|
|
|
|
DEVICE_MODEL := ZLT S12 PRO
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 comgt-ncm -uboot-envtools
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tozed_zlt-s12-pro
|
|
|
|
|
|
2023-03-14 01:06:40 +00:00
|
|
|
define Device/tplink_archer-ax23-v1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := Archer AX23
|
|
|
|
|
DEVICE_VARIANT := v1
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
|
|
|
|
TPLINK_BOARD_ID := ARCHER-AX23-V1
|
|
|
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
|
|
|
IMAGE_SIZE := 15744k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_archer-ax23-v1
|
|
|
|
|
|
2021-04-19 01:22:51 +00:00
|
|
|
define Device/tplink_archer-a6-v3
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := Archer A6
|
|
|
|
|
DEVICE_VARIANT := V3
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-mt7663-firmware-ap -uboot-envtools
|
2021-04-19 01:22:51 +00:00
|
|
|
TPLINK_BOARD_ID := ARCHER-A6-V3
|
|
|
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
|
|
|
IMAGE_SIZE := 15744k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_archer-a6-v3
|
|
|
|
|
|
2021-06-05 07:01:00 +00:00
|
|
|
define Device/tplink_archer-c6-v3
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := Archer C6
|
|
|
|
|
DEVICE_VARIANT := V3
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
2021-06-05 07:01:00 +00:00
|
|
|
TPLINK_BOARD_ID := ARCHER-C6-V3
|
|
|
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
|
|
|
IMAGE_SIZE := 15744k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_archer-c6-v3
|
|
|
|
|
|
ramips: add support for TP-Link Archer C6U v1 (EU)
This patch adds support for TP-Link Archer C6U v1 (EU).
The device is also known in some market as Archer C6 v3.
This patch supports only Archer C6U v1 (EU).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (Winbond 25Q128)
* WiFi 5GHz: Mediatek MT7613BEN (2x2:2)
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2)
* Ethernet: MT7630, 5x 1000Base-T.
* LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB
* Buttons: Reset, WPS.
* UART: Serial console (115200 8n1), J1(GND:3)
* USB: One USB2 port.
Installation:
------------
Install the OpenWrt factory image for C6U is from the
TP-Link web interface.
1) Go to "Advanced/System Tools/Firmware Update".
2) Click "Browse" and upload the OpenWrt factory image:
openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin.
3) Click the "Upgrade" button, and select "Yes" when prompted.
Recovery to stock firmware:
--------------------------
The C6U bootloader has a failsafe mode that provides a web
interface (running at 192.168.0.1) for reverting back to the
stock TP-Link firmware. The failsafe interface is triggered
from the serial console or on failed kernel boot. Unfortunately,
there's no key combination that enables the failsafe mode. This
gives us two options for recovery:
1) Recover using the serial console (J1 header).
The recovery interface can be selected by hitting 'x' when
prompted on boot.
2) Trigger the bootloader failsafe mode.
A more dangerous option is force the bootloader into
recovery mode by erasing the OpenWrt partition from the
OpenWrt's shell - e.g "mtd erase firmware". Please be
careful, since erasing the wrong partition can brick
your device.
MAC addresses:
-------------
OEM firmware configuration:
D8:07:B6:xx:xx:83 : 5G
D8:07:B6:xx:xx:84 : LAN (label)
D8:07:B6:xx:xx:84 : 2.4G
D8:07:B6:xx:xx:85 : WAN
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
2020-07-31 11:02:21 +00:00
|
|
|
define Device/tplink_archer-c6u-v1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := Archer C6U
|
|
|
|
|
DEVICE_VARIANT := v1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
kmod-usb3 kmod-usb-ledtrig-usbport -uboot-envtools
|
ramips: add support for TP-Link Archer C6U v1 (EU)
This patch adds support for TP-Link Archer C6U v1 (EU).
The device is also known in some market as Archer C6 v3.
This patch supports only Archer C6U v1 (EU).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (Winbond 25Q128)
* WiFi 5GHz: Mediatek MT7613BEN (2x2:2)
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2)
* Ethernet: MT7630, 5x 1000Base-T.
* LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB
* Buttons: Reset, WPS.
* UART: Serial console (115200 8n1), J1(GND:3)
* USB: One USB2 port.
Installation:
------------
Install the OpenWrt factory image for C6U is from the
TP-Link web interface.
1) Go to "Advanced/System Tools/Firmware Update".
2) Click "Browse" and upload the OpenWrt factory image:
openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin.
3) Click the "Upgrade" button, and select "Yes" when prompted.
Recovery to stock firmware:
--------------------------
The C6U bootloader has a failsafe mode that provides a web
interface (running at 192.168.0.1) for reverting back to the
stock TP-Link firmware. The failsafe interface is triggered
from the serial console or on failed kernel boot. Unfortunately,
there's no key combination that enables the failsafe mode. This
gives us two options for recovery:
1) Recover using the serial console (J1 header).
The recovery interface can be selected by hitting 'x' when
prompted on boot.
2) Trigger the bootloader failsafe mode.
A more dangerous option is force the bootloader into
recovery mode by erasing the OpenWrt partition from the
OpenWrt's shell - e.g "mtd erase firmware". Please be
careful, since erasing the wrong partition can brick
your device.
MAC addresses:
-------------
OEM firmware configuration:
D8:07:B6:xx:xx:83 : 5G
D8:07:B6:xx:xx:84 : LAN (label)
D8:07:B6:xx:xx:84 : 2.4G
D8:07:B6:xx:xx:85 : WAN
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
2020-07-31 11:02:21 +00:00
|
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
|
|
|
TPLINK_BOARD_ID := ARCHER-C6U-V1
|
|
|
|
|
IMAGE_SIZE := 15744k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_archer-c6u-v1
|
|
|
|
|
|
2023-01-29 15:01:40 +00:00
|
|
|
define Device/tplink_deco-m4r-v4
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := Deco M4R
|
|
|
|
|
DEVICE_VARIANT := v4
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
2023-01-29 15:01:40 +00:00
|
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
|
|
|
TPLINK_BOARD_ID := DECO-M4R-V4
|
|
|
|
|
IMAGE_SIZE := 15744k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_deco-m4r-v4
|
|
|
|
|
|
ramips: mt7621: add TP-Link EAP235-Wall support
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.
When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.
The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.
Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
* Back side: ETH0, PoE PD port
* Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)
Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).
Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
eth a4:2b:b0:...:88
ra0 a4:2b:b0:...:88
rai0 a4:2b:b0:...:89
Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface
Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
# tftpboot 84000000 openwrt-initramfs.bin
# bootm
Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
$ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
-z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin
This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.
Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
This was an issue with the ddc75ff704 version of mt76, but appears to
have improved/disappeared with bc3963764d.
Error notice example:
[ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout
Hardware was kindly provided for porting by Stijn Segers.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-02-18 19:52:53 +00:00
|
|
|
define Device/tplink_eap235-wall-v1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := EAP235-Wall
|
|
|
|
|
DEVICE_VARIANT := v1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
ramips: mt7621: add TP-Link EAP235-Wall support
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.
When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.
The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.
Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
* Back side: ETH0, PoE PD port
* Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)
Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).
Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
eth a4:2b:b0:...:88
ra0 a4:2b:b0:...:88
rai0 a4:2b:b0:...:89
Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface
Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
# tftpboot 84000000 openwrt-initramfs.bin
# bootm
Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
$ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
-z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin
This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.
Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
This was an issue with the ddc75ff704 version of mt76, but appears to
have improved/disappeared with bc3963764d.
Error notice example:
[ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout
Hardware was kindly provided for porting by Stijn Segers.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-02-18 19:52:53 +00:00
|
|
|
TPLINK_BOARD_ID := EAP235-WALL-V1
|
|
|
|
|
IMAGE_SIZE := 13440k
|
|
|
|
|
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory | \
|
|
|
|
|
pad-extra 128
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_eap235-wall-v1
|
|
|
|
|
|
2023-06-24 20:18:35 +00:00
|
|
|
define Device/tplink_eap613-v1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := EAP613
|
|
|
|
|
DEVICE_VARIANT := v1
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
|
|
|
|
TPLINK_BOARD_ID := EAP610-V3
|
|
|
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | pad-to 64k
|
|
|
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
|
|
|
|
|
IMAGE_SIZE := 13248k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_eap613-v1
|
|
|
|
|
|
ramips: support TP-Link EAP615-Wall
Add support for the TP-Link EAP615-Wall, an AX1800 Wall Plate WiFi 6 AP.
The device is very similar to the TP-Link EAP235-Wall.
Hardware:
* SoC: MediaTek MT7621AT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Ethernet: 4x GbE
* Back: ETH0 (PoE-PD)
* Bottom: ETH1, ETH2, ETH3 (PoE passthrough)
* WiFi: MT7905DAN/MT7975DN 2.4/5 GHz 2T2R
* LEDS: 1x white
* Buttons: 1x LED, 1x reset
Stock firmware uses a random MAC address for ethernet. OpenWrt uses the
MAC address that is on the device label for ethernet and the wireless
interfaces. MAC address must not be incremented, as this will cause MAC
address conflicts in case you have two devices with consecutive MAC
addresses. Instead, different locally administered addresses will be
generated automatically, based on the MAC on the label.
Installation via stock firmware:
* Enable SSH in the TP-Link web interface
* SSH to the device
* Run `cliclientd stopcs`
* Upload the OpenWrt factory image via the TP-Link web interface
Installation via bootloader:
* Solder TTL header. Pinout: 1: TX, 2: RX, 3: GND, 4: VCC, with pin 1
closest to ETH1. Baud rate 115200
* Interrupt boot process by holding a key during boot
* Boot the OpenWrt initramfs:
# tftpboot 0x84000000 openwrt-ramips-mt7621-tplink_eap615-wall-v1-initramfs-kernel.bin
# bootm
* Copy openwrt-ramips-mt7621-tplink_eap615-wall-v1-squashfs-sysupgrade.bin
to /tmp and use sysupgrade to install it
Thanks to Sander Vanheule for his work on the EAP235-Wall, which made
adding support for the EAP615-Wall very easy.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-01-27 21:42:33 +00:00
|
|
|
define Device/tplink_eap615-wall-v1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := EAP615-Wall
|
|
|
|
|
DEVICE_VARIANT := v1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
ramips: support TP-Link EAP615-Wall
Add support for the TP-Link EAP615-Wall, an AX1800 Wall Plate WiFi 6 AP.
The device is very similar to the TP-Link EAP235-Wall.
Hardware:
* SoC: MediaTek MT7621AT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Ethernet: 4x GbE
* Back: ETH0 (PoE-PD)
* Bottom: ETH1, ETH2, ETH3 (PoE passthrough)
* WiFi: MT7905DAN/MT7975DN 2.4/5 GHz 2T2R
* LEDS: 1x white
* Buttons: 1x LED, 1x reset
Stock firmware uses a random MAC address for ethernet. OpenWrt uses the
MAC address that is on the device label for ethernet and the wireless
interfaces. MAC address must not be incremented, as this will cause MAC
address conflicts in case you have two devices with consecutive MAC
addresses. Instead, different locally administered addresses will be
generated automatically, based on the MAC on the label.
Installation via stock firmware:
* Enable SSH in the TP-Link web interface
* SSH to the device
* Run `cliclientd stopcs`
* Upload the OpenWrt factory image via the TP-Link web interface
Installation via bootloader:
* Solder TTL header. Pinout: 1: TX, 2: RX, 3: GND, 4: VCC, with pin 1
closest to ETH1. Baud rate 115200
* Interrupt boot process by holding a key during boot
* Boot the OpenWrt initramfs:
# tftpboot 0x84000000 openwrt-ramips-mt7621-tplink_eap615-wall-v1-initramfs-kernel.bin
# bootm
* Copy openwrt-ramips-mt7621-tplink_eap615-wall-v1-squashfs-sysupgrade.bin
to /tmp and use sysupgrade to install it
Thanks to Sander Vanheule for his work on the EAP235-Wall, which made
adding support for the EAP615-Wall very easy.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-01-27 21:42:33 +00:00
|
|
|
TPLINK_BOARD_ID := EAP615-WALL-V1
|
|
|
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | pad-to 64k
|
|
|
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
|
|
|
|
|
IMAGE_SIZE := 13248k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_eap615-wall-v1
|
|
|
|
|
|
ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
| J2
|
+--- Don't connect
Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
pressing 't'
3. Load and run OpenWrt initramfs image:
tftpboot
bootm
4. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
the OEM firmware
MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
| | MAC example 1 | MAC example 2 | Algorithm |
+---------+-------------------+-------------------+-------------+
| label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).
Notes
-----
[1] WAN MAC address:
a. First octet of WAN MAC is differ than others and OUI is not related
to TP-Link company. This probably should be fixed.
b. Flipping bits in first octet and hex delta are different for the
different MAC examples:
+-----------------+----------------+----------------+
| | Example 1 | Example 2 |
+-----------------+----------------+----------------+
| LAN | 68 = 0110 1000 | 50 = 0101 0000 |
| MAC (1st octet) | ^ ^ ^ | |
+-----------------+----------------+----------------+
| WAN | 72 = 0111 0010 | 54 = 0101 0100 |
| MAC (1st octet) | ^ ^ ^ | ^ |
+-----------------+----------------+----------------+
| HEX delta | 0xa | 0x4 |
+-----------------+----------------+----------------+
| DEC delta | 4 | 4 |
+-----------------+----------------+----------------+
c. DEC delta is a constant (4). This looks like a mistake in OEM
firmware and probably should be fixed.
Based on the above, I decided to keep correct OUI and make WAN MAC =
label + 1.
[2] Bootloaders
The device contains 3 bootloaders:
- First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
located on NAND Flash to load next full-feature Uboot.
- Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
bootloader includes recovery webserver. Requires special uImages to
continue the boot process:
0x00 (os0, os1) - firmware uImage
0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
- Additionally, both slots of the original TP-Link firmware contains
Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
magics and CRCs. We don't use this U-Boot with OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-06 15:47:58 +00:00
|
|
|
define Device/tplink_ec330-g5u-v1
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
| J2
|
+--- Don't connect
Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
pressing 't'
3. Load and run OpenWrt initramfs image:
tftpboot
bootm
4. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
the OEM firmware
MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
| | MAC example 1 | MAC example 2 | Algorithm |
+---------+-------------------+-------------------+-------------+
| label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).
Notes
-----
[1] WAN MAC address:
a. First octet of WAN MAC is differ than others and OUI is not related
to TP-Link company. This probably should be fixed.
b. Flipping bits in first octet and hex delta are different for the
different MAC examples:
+-----------------+----------------+----------------+
| | Example 1 | Example 2 |
+-----------------+----------------+----------------+
| LAN | 68 = 0110 1000 | 50 = 0101 0000 |
| MAC (1st octet) | ^ ^ ^ | |
+-----------------+----------------+----------------+
| WAN | 72 = 0111 0010 | 54 = 0101 0100 |
| MAC (1st octet) | ^ ^ ^ | ^ |
+-----------------+----------------+----------------+
| HEX delta | 0xa | 0x4 |
+-----------------+----------------+----------------+
| DEC delta | 4 | 4 |
+-----------------+----------------+----------------+
c. DEC delta is a constant (4). This looks like a mistake in OEM
firmware and probably should be fixed.
Based on the above, I decided to keep correct OUI and make WAN MAC =
label + 1.
[2] Bootloaders
The device contains 3 bootloaders:
- First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
located on NAND Flash to load next full-feature Uboot.
- Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
bootloader includes recovery webserver. Requires special uImages to
continue the boot process:
0x00 (os0, os1) - firmware uImage
0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
- Additionally, both slots of the original TP-Link firmware contains
Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
magics and CRCs. We don't use this U-Boot with OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-06 15:47:58 +00:00
|
|
|
LOADER := bin
|
|
|
|
|
IMAGE_SIZE := 49152k
|
|
|
|
|
DEVICE_VENDOR := TP-Link
|
|
|
|
|
DEVICE_MODEL := EC330-G5u
|
|
|
|
|
DEVICE_ALT0_VENDOR := TP-Link
|
|
|
|
|
DEVICE_ALT0_MODEL := Archer C9ERT
|
|
|
|
|
DEVICE_VARIANT := v1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb-ledtrig-usbport kmod-usb3
|
ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
| J2
|
+--- Don't connect
Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
pressing 't'
3. Load and run OpenWrt initramfs image:
tftpboot
bootm
4. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
the OEM firmware
MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
| | MAC example 1 | MAC example 2 | Algorithm |
+---------+-------------------+-------------------+-------------+
| label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).
Notes
-----
[1] WAN MAC address:
a. First octet of WAN MAC is differ than others and OUI is not related
to TP-Link company. This probably should be fixed.
b. Flipping bits in first octet and hex delta are different for the
different MAC examples:
+-----------------+----------------+----------------+
| | Example 1 | Example 2 |
+-----------------+----------------+----------------+
| LAN | 68 = 0110 1000 | 50 = 0101 0000 |
| MAC (1st octet) | ^ ^ ^ | |
+-----------------+----------------+----------------+
| WAN | 72 = 0111 0010 | 54 = 0101 0100 |
| MAC (1st octet) | ^ ^ ^ | ^ |
+-----------------+----------------+----------------+
| HEX delta | 0xa | 0x4 |
+-----------------+----------------+----------------+
| DEC delta | 4 | 4 |
+-----------------+----------------+----------------+
c. DEC delta is a constant (4). This looks like a mistake in OEM
firmware and probably should be fixed.
Based on the above, I decided to keep correct OUI and make WAN MAC =
label + 1.
[2] Bootloaders
The device contains 3 bootloaders:
- First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
located on NAND Flash to load next full-feature Uboot.
- Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
bootloader includes recovery webserver. Requires special uImages to
continue the boot process:
0x00 (os0, os1) - firmware uImage
0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
- Additionally, both slots of the original TP-Link firmware contains
Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
magics and CRCs. We don't use this U-Boot with OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-06 15:47:58 +00:00
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
|
|
|
uImage-tplink-c9 standalone '$(call toupper,$(LINUX_KARCH)) \
|
|
|
|
|
$(VERSION_DIST) Linux-$(LINUX_VERSION)' | \
|
|
|
|
|
uImage-tplink-c9 firmware 'OS IMAGE ($(VERSION_DIST))'
|
|
|
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | loader-kernel | \
|
|
|
|
|
uImage none
|
2023-04-22 09:35:44 +00:00
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
|
|
|
|
append-ubi | check-size
|
ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
| J2
|
+--- Don't connect
Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
pressing 't'
3. Load and run OpenWrt initramfs image:
tftpboot
bootm
4. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
the OEM firmware
MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
| | MAC example 1 | MAC example 2 | Algorithm |
+---------+-------------------+-------------------+-------------+
| label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).
Notes
-----
[1] WAN MAC address:
a. First octet of WAN MAC is differ than others and OUI is not related
to TP-Link company. This probably should be fixed.
b. Flipping bits in first octet and hex delta are different for the
different MAC examples:
+-----------------+----------------+----------------+
| | Example 1 | Example 2 |
+-----------------+----------------+----------------+
| LAN | 68 = 0110 1000 | 50 = 0101 0000 |
| MAC (1st octet) | ^ ^ ^ | |
+-----------------+----------------+----------------+
| WAN | 72 = 0111 0010 | 54 = 0101 0100 |
| MAC (1st octet) | ^ ^ ^ | ^ |
+-----------------+----------------+----------------+
| HEX delta | 0xa | 0x4 |
+-----------------+----------------+----------------+
| DEC delta | 4 | 4 |
+-----------------+----------------+----------------+
c. DEC delta is a constant (4). This looks like a mistake in OEM
firmware and probably should be fixed.
Based on the above, I decided to keep correct OUI and make WAN MAC =
label + 1.
[2] Bootloaders
The device contains 3 bootloaders:
- First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
located on NAND Flash to load next full-feature Uboot.
- Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
bootloader includes recovery webserver. Requires special uImages to
continue the boot process:
0x00 (os0, os1) - firmware uImage
0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
- Additionally, both slots of the original TP-Link firmware contains
Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
magics and CRCs. We don't use this U-Boot with OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-06 15:47:58 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_ec330-g5u-v1
|
|
|
|
|
|
2022-12-15 01:26:38 +00:00
|
|
|
define Device/tplink_er605-v2
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-12-15 01:26:38 +00:00
|
|
|
DEVICE_VENDOR := TP-Link
|
|
|
|
|
DEVICE_MODEL := ER605
|
|
|
|
|
DEVICE_VARIANT := v2
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := -wpad-basic-mbedtls kmod-usb3 -uboot-envtools
|
2022-12-15 01:26:38 +00:00
|
|
|
KERNEL_IN_UBI := 1
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
IMAGES += sysupgrade.tar
|
|
|
|
|
IMAGE_SIZE := 127744k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_er605-v2
|
|
|
|
|
|
2023-11-24 00:31:05 +00:00
|
|
|
define Device/tplink_ex220-v1
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := TP-Link
|
|
|
|
|
DEVICE_MODEL := EX220
|
|
|
|
|
DEVICE_VARIANT := v1
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
|
|
|
|
TPLINK_BOARD_ID := EX220-V1
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
IMAGE_SIZE := 15744k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_ex220-v1
|
|
|
|
|
|
ramips: add support for TP-Link MR600 V2(EU)
MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation
etc. and can reportedly achieve higher bandwidth with it.
- Specifications:
* SoC: Mediatek MT7621DAT 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* LTE Modem: Qualcomm MDM9240
* WiFi 5GHz: Mediatek MT7613BEN
* WiFi 2.4GHz: Mediatek MT7603EN
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console (115200 8n1), J1(GND:3)
* Buttons: Reset, WPS.
* LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2,
Signal3
- MAC Addresses:
OEM firmware configuration:
54:af:97:xx:xx:7b : 2.4G
54:af:97:xx:xx:7a : 5G
54:af:97:xx:xx:7c : LTE
54:af:97:xx:xx:7b : LAN (label)
54:af:97:xx:xx:7c : WAN
- Installation:
1. Download the OpenWrt initramfs-image.
Place it into a TFTP server root directory and rename it to openwrt.img
Configure the TFTP server to listen at 192.168.0.5/24.
3. Connect to the serial console.
Attach power and interrupt the boot procedure when prompted (type `tpl`).
Credentials are admin / 1234
4. Configure U-Boot for booting OpenWrt from ram
$ tftpboot
$ bootm
5. Transfer the OpenWrt sysupgrade image to the device.
- LTE:
In order to setup the wwan0 interface:
1. Add a `qmi` proto interface under `/etc/config/network`, e.g.:
```
config interface 'wwan0'
option device '/dev/cdc-wdm0'
option proto 'qmi'
option pincode 'XXXX'
option apn 'your_isp_apn'
```
2. Add `wwan0` interface to the `wan` firewall zone
3. `/etc/init.d/network restart`
Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
2022-10-02 22:30:28 +00:00
|
|
|
define Device/tplink_mr600-v2-eu
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-v2)
|
|
|
|
|
DEVICE_MODEL := MR600
|
|
|
|
|
DEVICE_VARIANT := v2 (EU)
|
|
|
|
|
TPLINK_FLASHLAYOUT := 16Mltq
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-net-qmi-wwan uqmi kmod-usb3 -uboot-envtools
|
2023-04-02 08:40:47 +00:00
|
|
|
IMAGE/factory.bin := tplink-v2-image -e -a 0x10000
|
|
|
|
|
IMAGE/sysupgrade.bin := tplink-v2-image -s -e -a 0x10000 | check-size | \
|
|
|
|
|
append-metadata
|
ramips: add support for TP-Link MR600 V2(EU)
MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation
etc. and can reportedly achieve higher bandwidth with it.
- Specifications:
* SoC: Mediatek MT7621DAT 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* LTE Modem: Qualcomm MDM9240
* WiFi 5GHz: Mediatek MT7613BEN
* WiFi 2.4GHz: Mediatek MT7603EN
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console (115200 8n1), J1(GND:3)
* Buttons: Reset, WPS.
* LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2,
Signal3
- MAC Addresses:
OEM firmware configuration:
54:af:97:xx:xx:7b : 2.4G
54:af:97:xx:xx:7a : 5G
54:af:97:xx:xx:7c : LTE
54:af:97:xx:xx:7b : LAN (label)
54:af:97:xx:xx:7c : WAN
- Installation:
1. Download the OpenWrt initramfs-image.
Place it into a TFTP server root directory and rename it to openwrt.img
Configure the TFTP server to listen at 192.168.0.5/24.
3. Connect to the serial console.
Attach power and interrupt the boot procedure when prompted (type `tpl`).
Credentials are admin / 1234
4. Configure U-Boot for booting OpenWrt from ram
$ tftpboot
$ bootm
5. Transfer the OpenWrt sysupgrade image to the device.
- LTE:
In order to setup the wwan0 interface:
1. Add a `qmi` proto interface under `/etc/config/network`, e.g.:
```
config interface 'wwan0'
option device '/dev/cdc-wdm0'
option proto 'qmi'
option pincode 'XXXX'
option apn 'your_isp_apn'
```
2. Add `wwan0` interface to the `wan` firewall zone
3. `/etc/init.d/network restart`
Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
2022-10-02 22:30:28 +00:00
|
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL) | tplink-v2-header
|
|
|
|
|
TPLINK_BOARD_ID := MR600-V2-EU
|
|
|
|
|
IMAGE_SIZE := 16384k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_mr600-v2-eu
|
|
|
|
|
|
ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-17 18:17:45 +00:00
|
|
|
define Device/tplink_re350-v1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-17 18:17:45 +00:00
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := RE350
|
|
|
|
|
DEVICE_VARIANT := v1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 -uboot-envtools
|
ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-17 18:17:45 +00:00
|
|
|
TPLINK_BOARD_ID := RE350-V1
|
|
|
|
|
IMAGE_SIZE := 6016k
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += re350-v1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_re350-v1
|
|
|
|
|
|
ramips: add support for TP-Link RE500 v1
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 21:05:25 +00:00
|
|
|
define Device/tplink_re500-v1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
ramips: add support for TP-Link RE500 v1
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 21:05:25 +00:00
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := RE500
|
|
|
|
|
DEVICE_VARIANT := v1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
ramips: add support for TP-Link RE500 v1
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 21:05:25 +00:00
|
|
|
TPLINK_BOARD_ID := RE500-V1
|
|
|
|
|
IMAGE_SIZE := 14208k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_re500-v1
|
|
|
|
|
|
ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-17 18:17:45 +00:00
|
|
|
define Device/tplink_re650-v1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-17 18:17:45 +00:00
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := RE650
|
|
|
|
|
DEVICE_VARIANT := v1
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-17 18:17:45 +00:00
|
|
|
TPLINK_BOARD_ID := RE650-V1
|
|
|
|
|
IMAGE_SIZE := 14208k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_re650-v1
|
|
|
|
|
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
define Device/tplink_re650-v2
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := RE650
|
|
|
|
|
DEVICE_VARIANT := v2
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware -uboot-envtools
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
TPLINK_BOARD_ID := RE650-V2
|
|
|
|
|
IMAGE_SIZE := 7994k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_re650-v2
|
|
|
|
|
|
2022-02-19 21:32:54 +00:00
|
|
|
define Device/tplink_tl-wpa8631p-v3
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/tplink-safeloader)
|
|
|
|
|
DEVICE_MODEL := TL-WPA8631P
|
|
|
|
|
DEVICE_VARIANT := v3
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
2022-02-19 21:32:54 +00:00
|
|
|
TPLINK_BOARD_ID := TL-WPA8631P-V3
|
|
|
|
|
IMAGE_SIZE := 7232k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_tl-wpa8631p-v3
|
|
|
|
|
|
2020-04-07 08:47:18 +00:00
|
|
|
define Device/ubnt_edgerouter_common
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-15 01:32:02 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2020-04-07 08:47:18 +00:00
|
|
|
DEVICE_VENDOR := Ubiquiti
|
2019-07-15 12:55:24 +00:00
|
|
|
IMAGE_SIZE := 256768k
|
2016-11-19 17:27:22 +00:00
|
|
|
FILESYSTEMS := squashfs
|
|
|
|
|
KERNEL_SIZE := 3145728
|
2019-12-19 18:40:33 +00:00
|
|
|
KERNEL_INITRAMFS := $$(KERNEL) | \
|
|
|
|
|
ubnt-erx-factory-image $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.tar
|
2018-11-29 09:48:03 +00:00
|
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += -wpad-basic-mbedtls -uboot-envtools
|
2020-04-07 08:47:18 +00:00
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/ubnt_edgerouter-x
|
|
|
|
|
$(Device/ubnt_edgerouter_common)
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_MODEL := EdgeRouter X
|
2020-04-07 08:47:18 +00:00
|
|
|
SUPPORTED_DEVICES += ubnt-erx ubiquiti,edgerouterx
|
2016-04-01 07:11:48 +00:00
|
|
|
endef
|
2020-04-07 08:47:18 +00:00
|
|
|
TARGET_DEVICES += ubnt_edgerouter-x
|
2016-04-01 07:11:48 +00:00
|
|
|
|
2020-04-07 08:47:18 +00:00
|
|
|
define Device/ubnt_edgerouter-x-sfp
|
|
|
|
|
$(Device/ubnt_edgerouter_common)
|
|
|
|
|
DEVICE_MODEL := EdgeRouter X SFP
|
2022-02-19 07:35:10 +00:00
|
|
|
DEVICE_ALT0_VENDOR := Ubiquiti
|
|
|
|
|
DEVICE_ALT0_MODEL := EdgePoint R6
|
2020-04-07 21:50:31 +00:00
|
|
|
DEVICE_PACKAGES += kmod-i2c-algo-pca kmod-gpio-pca953x kmod-sfp
|
2020-04-07 08:47:18 +00:00
|
|
|
SUPPORTED_DEVICES += ubnt-erx-sfp ubiquiti,edgerouterx-sfp
|
2017-05-29 09:24:49 +00:00
|
|
|
endef
|
2020-04-07 08:47:18 +00:00
|
|
|
TARGET_DEVICES += ubnt_edgerouter-x-sfp
|
2017-05-29 09:24:49 +00:00
|
|
|
|
ramips: add support for Ubiquiti UniFi 6 Lite
Hardware
--------
MediaTek MT7621AT
256M DDR3
32M SPI-NOR
MediaTek MT7603 2T2R 802.11n 2.4GHz
MediaTek MT7915 2T2R 802.11ax 5GHz
Not Working
-----------
- Bluetooth (connected to UART3)
UART
----
UART is located in the lower left corner of the board. Pinout is
0 - 3V3 (don't connect)
1 - RX
2 - TX
3 - GND
Console is 115200 8N1.
Boot
----
1. Connect to the serial console and connect power.
2. Double-press ESC when prompted
3. Set the fdt address
$ fdt addr $(fdtcontroladdr)
4. Remove the signature node from the control FDT
$ fdt rm /signature
5. Transfer and boot the OpenWrt initramfs image to the device.
Make sure to name the file C0A80114.img and have it reachable at
192.168.1.1/24
$ tftpboot; bootm
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Update the bootloader environment.
$ fw_setenv devmode TRUE
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
3. Transfer the OpenWrt sysupgrade image to the device using SCP.
4. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
5. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
7. Reboot the device. It should boot into OpenWrt.
Below are the original installation instructions prior to the discovery
of "devmode=TRUE". They are not required for installation and are
documentation only.
The bootloader employs signature verification on the FIT image
configurations. This way, booting unauthorized image without patching
the bootloader is not possible. Manually configuring the bootcmd in the
U-Boot envronment won't work, as this is restored to the default value
if modified.
The bootloader is made up of three different parts.
1. The SPL performing early board initialization and providing a XModem
recovery in case the PBL is missing
2. The PBL being the primary U-Boot application and containing the
control FDT. It is LZMA packed with a uImage header.
3. A Ubiquiti standalone U-Boot application providing the main boot
routine as well as their recovery mechanism.
In a perfect world, we would only replace the PBL, as the SPL does not
perform checks on the PBLs integrity. However, as the PBL is in the same
eraseblock as the SPL, we need to at least rewrite both.
The bootloader will only verify integrity in case it has a "signature"
node in it's control device-tree. Renaming the signature node to
something else will prevent this from happening.
Warning: These instructions are based on the firmware intially
shipped with the device and potentially brick your device in a way it
can only be recovered using a SPI flasher.
Only (!) proceed if you understand this!
1. Extract the bootloader from the U-Boot partition using the OpenWrt
initramfs image.
2. Split the bootloader into it's 3 components:
$ dd if=bootloader.bin of=spl.bin bs=1 skip=0 count=45056
$ dd if=bootloader.bin of=pbl.uimage bs=1 skip=45056 count=143360
$ dd if=bootloader.bin of=ubnt.uimage bs=1 skip=188416
3. Strip the uImage header from the PBL
$ dd if=pbl.uimage of=pbl.lzma bs=64 skip=1
4. Decompress the PBL
$ lzma -d pbl.lzma --single-stream
The decompressed PBL sha256sum should be
d8b406c65240d260cf15be5f97f40c1d6d1b6e61ec3abed37bb841c90fcc1235
5. Open the decompressed PBL using your favorite hexeditor. Locate the
control FDT at offset 0x4CED0 (0xD00DFEED). At offset 0x4D5BC, the
label for the signature node is located. Rename the "signature"
string at this offset to "signaturr".
The patched PBL sha256sum should be
d028e374cdb40ba44b6e3cef2e4e8a8c16a3b85eb15d9544d24fdd10eed64c97
6. Compress the patched PBL
$ lzma -z pbl --lzma1=dict=67108864
The resulting pbl.lzma file should have the sha256sum
7ae6118928fa0d0b3fe4ff81abd80ecfd9ba2944cb0f0a462b6ae65913088b42
7. Create the PBL uimage
$ SOURCE_DATE_EPOCH=1607909492 mkimage -A mips -O u-boot -C lzma
-n "U-Boot 2018.03 [UniFi,v1.1.40.71]" -a 84000000 -e 84000000
-T firmware -d pbl.lzma patched_pbl.uimage
The resulting patched_pbl.uimage should have the sha256sum
b90d7fa2dcc6814180d3943530d8d6b0d6a03636113c94e99af34f196d3cf2ce
8. Reassemble the complete bootloader
$ dd if=patched_pbl.uimage of=aligned_pbl.uimage bs=143360 count=1
conv=sync
$ cat spl.bin > patched_uboot.bin
$ cat aligned_pbl.uimage >> patched_uboot.bin
$ cat ubnt.uimage >> patched_uboot.bin
The resulting patched_uboot.bin should have the sha256sum
3e1186f33b88a525687285c2a8b22e8786787b31d4648b8eee66c672222aa76b
9. Transfer your patched bootloader to the device. Also install the
kmod-mtd-rw package using opkg and load it.
$ insmod mtd-rw.ko i_want_a_brick=1
Write the patched bootloader to mtd0
$ mtd write patched_uboot.bin u-boot
10. Erase the kernel1 partition, as the bootloader might otherwise
decide to boot from there.
$ mtd erase kernel1
11. Transfer the OpenWrt sysupgrade image to the device and install
using sysupgrade.
FIT configurations
------------------
In the future, the MT7621 UniFi6 family can be supported by a single
OpenWrt image.
config@1: U6 Lite
config@2: U6 IW
config@3: U6 Mesh
config@4: U6 Extender
config@5: U6 LR-EA (Early Access - GA is MT7622)
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-12-12 13:34:00 +00:00
|
|
|
define Device/ubnt_unifi-6-lite
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Ubiquiti
|
|
|
|
|
DEVICE_MODEL := UniFi 6 Lite
|
2021-03-17 23:54:25 +00:00
|
|
|
DEVICE_DTS_CONFIG := config@1
|
2022-11-06 23:42:57 +00:00
|
|
|
DEVICE_DTS_LOADADDR := 0x87000000
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7915-firmware -uboot-envtools
|
ramips: add support for Ubiquiti UniFi 6 Lite
Hardware
--------
MediaTek MT7621AT
256M DDR3
32M SPI-NOR
MediaTek MT7603 2T2R 802.11n 2.4GHz
MediaTek MT7915 2T2R 802.11ax 5GHz
Not Working
-----------
- Bluetooth (connected to UART3)
UART
----
UART is located in the lower left corner of the board. Pinout is
0 - 3V3 (don't connect)
1 - RX
2 - TX
3 - GND
Console is 115200 8N1.
Boot
----
1. Connect to the serial console and connect power.
2. Double-press ESC when prompted
3. Set the fdt address
$ fdt addr $(fdtcontroladdr)
4. Remove the signature node from the control FDT
$ fdt rm /signature
5. Transfer and boot the OpenWrt initramfs image to the device.
Make sure to name the file C0A80114.img and have it reachable at
192.168.1.1/24
$ tftpboot; bootm
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Update the bootloader environment.
$ fw_setenv devmode TRUE
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
3. Transfer the OpenWrt sysupgrade image to the device using SCP.
4. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
5. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
7. Reboot the device. It should boot into OpenWrt.
Below are the original installation instructions prior to the discovery
of "devmode=TRUE". They are not required for installation and are
documentation only.
The bootloader employs signature verification on the FIT image
configurations. This way, booting unauthorized image without patching
the bootloader is not possible. Manually configuring the bootcmd in the
U-Boot envronment won't work, as this is restored to the default value
if modified.
The bootloader is made up of three different parts.
1. The SPL performing early board initialization and providing a XModem
recovery in case the PBL is missing
2. The PBL being the primary U-Boot application and containing the
control FDT. It is LZMA packed with a uImage header.
3. A Ubiquiti standalone U-Boot application providing the main boot
routine as well as their recovery mechanism.
In a perfect world, we would only replace the PBL, as the SPL does not
perform checks on the PBLs integrity. However, as the PBL is in the same
eraseblock as the SPL, we need to at least rewrite both.
The bootloader will only verify integrity in case it has a "signature"
node in it's control device-tree. Renaming the signature node to
something else will prevent this from happening.
Warning: These instructions are based on the firmware intially
shipped with the device and potentially brick your device in a way it
can only be recovered using a SPI flasher.
Only (!) proceed if you understand this!
1. Extract the bootloader from the U-Boot partition using the OpenWrt
initramfs image.
2. Split the bootloader into it's 3 components:
$ dd if=bootloader.bin of=spl.bin bs=1 skip=0 count=45056
$ dd if=bootloader.bin of=pbl.uimage bs=1 skip=45056 count=143360
$ dd if=bootloader.bin of=ubnt.uimage bs=1 skip=188416
3. Strip the uImage header from the PBL
$ dd if=pbl.uimage of=pbl.lzma bs=64 skip=1
4. Decompress the PBL
$ lzma -d pbl.lzma --single-stream
The decompressed PBL sha256sum should be
d8b406c65240d260cf15be5f97f40c1d6d1b6e61ec3abed37bb841c90fcc1235
5. Open the decompressed PBL using your favorite hexeditor. Locate the
control FDT at offset 0x4CED0 (0xD00DFEED). At offset 0x4D5BC, the
label for the signature node is located. Rename the "signature"
string at this offset to "signaturr".
The patched PBL sha256sum should be
d028e374cdb40ba44b6e3cef2e4e8a8c16a3b85eb15d9544d24fdd10eed64c97
6. Compress the patched PBL
$ lzma -z pbl --lzma1=dict=67108864
The resulting pbl.lzma file should have the sha256sum
7ae6118928fa0d0b3fe4ff81abd80ecfd9ba2944cb0f0a462b6ae65913088b42
7. Create the PBL uimage
$ SOURCE_DATE_EPOCH=1607909492 mkimage -A mips -O u-boot -C lzma
-n "U-Boot 2018.03 [UniFi,v1.1.40.71]" -a 84000000 -e 84000000
-T firmware -d pbl.lzma patched_pbl.uimage
The resulting patched_pbl.uimage should have the sha256sum
b90d7fa2dcc6814180d3943530d8d6b0d6a03636113c94e99af34f196d3cf2ce
8. Reassemble the complete bootloader
$ dd if=patched_pbl.uimage of=aligned_pbl.uimage bs=143360 count=1
conv=sync
$ cat spl.bin > patched_uboot.bin
$ cat aligned_pbl.uimage >> patched_uboot.bin
$ cat ubnt.uimage >> patched_uboot.bin
The resulting patched_uboot.bin should have the sha256sum
3e1186f33b88a525687285c2a8b22e8786787b31d4648b8eee66c672222aa76b
9. Transfer your patched bootloader to the device. Also install the
kmod-mtd-rw package using opkg and load it.
$ insmod mtd-rw.ko i_want_a_brick=1
Write the patched bootloader to mtd0
$ mtd write patched_uboot.bin u-boot
10. Erase the kernel1 partition, as the bootloader might otherwise
decide to boot from there.
$ mtd erase kernel1
11. Transfer the OpenWrt sysupgrade image to the device and install
using sysupgrade.
FIT configurations
------------------
In the future, the MT7621 UniFi6 family can be supported by a single
OpenWrt image.
config@1: U6 Lite
config@2: U6 IW
config@3: U6 Mesh
config@4: U6 Extender
config@5: U6 LR-EA (Early Access - GA is MT7622)
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-12-12 13:34:00 +00:00
|
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
IMAGE_SIZE := 15424k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += ubnt_unifi-6-lite
|
|
|
|
|
|
2021-05-01 11:51:51 +00:00
|
|
|
define Device/ubnt_unifi-flexhd
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Ubiquiti
|
|
|
|
|
DEVICE_MODEL := UniFi FlexHD
|
|
|
|
|
DEVICE_DTS_CONFIG := config@2
|
2022-11-17 21:48:10 +00:00
|
|
|
DEVICE_DTS_LOADADDR := 0x87000000
|
2021-05-01 11:51:51 +00:00
|
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615-firmware kmod-leds-ubnt-ledbar \
|
|
|
|
|
-uboot-envtools
|
2021-05-01 11:51:51 +00:00
|
|
|
IMAGE_SIZE := 15552k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += ubnt_unifi-flexhd
|
|
|
|
|
|
2020-03-08 20:39:19 +00:00
|
|
|
define Device/ubnt_unifi-nanohd
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-03-08 20:39:19 +00:00
|
|
|
DEVICE_VENDOR := Ubiquiti
|
|
|
|
|
DEVICE_MODEL := UniFi nanoHD
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615-firmware -uboot-envtools
|
2020-03-08 20:39:19 +00:00
|
|
|
IMAGE_SIZE := 15552k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += ubnt_unifi-nanohd
|
|
|
|
|
|
2021-08-20 11:23:42 +00:00
|
|
|
define Device/ubnt_usw-flex
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Ubiquiti
|
|
|
|
|
DEVICE_MODEL := UniFi Switch Flex
|
|
|
|
|
DEVICE_DTS_CONFIG := config@1
|
2022-11-17 21:48:10 +00:00
|
|
|
DEVICE_DTS_LOADADDR := 0x87000000
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += -uboot-envtools
|
2021-08-20 11:23:42 +00:00
|
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
2022-11-17 22:02:13 +00:00
|
|
|
IMAGE_SIZE := 14720k
|
2021-08-20 11:23:42 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += ubnt_usw-flex
|
|
|
|
|
|
ramips: add support for UniElec U7621-01
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button
Installation:
This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-21 14:04:49 +00:00
|
|
|
define Device/unielec_u7621-01-16m
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := UniElec
|
|
|
|
|
DEVICE_MODEL := U7621-01
|
|
|
|
|
DEVICE_VARIANT := 16M
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 -uboot-envtools
|
ramips: add support for UniElec U7621-01
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button
Installation:
This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-21 14:04:49 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += unielec_u7621-01-16m
|
|
|
|
|
|
2019-08-16 12:05:53 +00:00
|
|
|
define Device/unielec_u7621-06-16m
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-10-23 01:42:03 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2018-11-27 23:31:10 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := UniElec
|
|
|
|
|
DEVICE_MODEL := U7621-06
|
2019-08-16 12:05:53 +00:00
|
|
|
DEVICE_VARIANT := 16M
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 \
|
|
|
|
|
-wpad-basic-mbedtls -uboot-envtools
|
2019-08-16 12:05:53 +00:00
|
|
|
SUPPORTED_DEVICES += u7621-06-256M-16M unielec,u7621-06-256m-16m
|
2018-11-27 23:31:10 +00:00
|
|
|
endef
|
2019-10-21 15:51:29 +00:00
|
|
|
TARGET_DEVICES += unielec_u7621-06-16m
|
2018-11-27 23:31:10 +00:00
|
|
|
|
2022-12-18 14:14:36 +00:00
|
|
|
define Device/unielec_u7621-06-32m
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 32448k
|
|
|
|
|
DEVICE_VENDOR := UniElec
|
|
|
|
|
DEVICE_MODEL := U7621-06
|
|
|
|
|
DEVICE_VARIANT := 32M
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 \
|
|
|
|
|
-wpad-basic-mbedtls -uboot-envtools
|
2022-12-18 14:14:36 +00:00
|
|
|
SUPPORTED_DEVICES += unielec,u7621-06-32m
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += unielec_u7621-06-32m
|
|
|
|
|
|
2019-08-16 12:05:53 +00:00
|
|
|
define Device/unielec_u7621-06-64m
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-10-23 01:42:03 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2018-10-24 14:23:20 +00:00
|
|
|
IMAGE_SIZE := 65216k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := UniElec
|
|
|
|
|
DEVICE_MODEL := U7621-06
|
2019-08-16 12:05:53 +00:00
|
|
|
DEVICE_VARIANT := 64M
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-usb3 \
|
|
|
|
|
-wpad-basic-mbedtls -uboot-envtools
|
2019-08-16 12:05:53 +00:00
|
|
|
SUPPORTED_DEVICES += unielec,u7621-06-512m-64m
|
2018-10-24 14:23:20 +00:00
|
|
|
endef
|
2019-10-21 15:51:29 +00:00
|
|
|
TARGET_DEVICES += unielec_u7621-06-64m
|
2018-10-24 14:23:20 +00:00
|
|
|
|
ramips: add support for Wavlink WL-WN531A6
This patch adds support for Wavlink WL-WN531A6 (Quantum D6).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3, Nanya NT5CB64M16GP-EK
* Flash: 16MB SPI NOR flash, GigaDevice GD25Q127CSIG
* WiFi 5GHz: Mediatek MT7615N (4x4:4) on mini PCIE slot.
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) on mini PCIE slot.
* Ethernet: MT7630, 5x 1000Base-T
* LED: Power, WAN, LAN(x4), WiFi, WPS, dual color
"WAVLINK" LED logo on the top cover.
* Buttons: Reset, WPS, "Turbo", touch button on the top
cover via RH6015C touch sensor.
* UART: UART1: serial console (57600 8n1) on the J4 header
located below the top heatsink.
UART2: J12 header, located on the right side of
the board.
* USB: One USB3 port.
* I2C: J9 header, located below the top heatsink.
Backup the OEM Firmware:
-----------------------
There isn't any firmware released for the WL-WN531A6 on
the Wavlink web site. Reverting back to the OEM firmware is
not possible unless we have a backup of the original OEM
firmware.
The OEM firmware is stored on /dev/mtd4 ("Kernel").
1) Plug a FAT32 formatted USB flash drive into the USB port.
2) Navigate to "Setup->USB Storage". Under the "Available
Network folder" you can see part of the mount point of
the newly mounted flash drive filesystem - e.g "sda1".
The full mount point is prefixed with "/media", so in
this case the mount point becomes "/media/sda1".
3) Go to http://192.168.10.1/webcmd.shtml .
4) Type the following line in the "Command" input box:
dd if=/dev/mtd4ro of=/media/sda1/firmware.bin
5) Click "Apply"
6) After few seconds, in the text area should appear this
output:
30080+0 records in
30080+0 records out
7) Type "sync" in the "Command" input box and click "Apply".
8) At this point the OEM firmware is stored on the flash
drive as "firmware.bin". The size of the file is 15040 KB.
Installation:
------------
* Flashing instructions (OEM web interface):
The OEM web interface accepts only files with names containing
"WN531A6". It's also impossible to flash the *-sysupgrade.bin
image, so we have to flash the *-initramfs-kernel.bin first and
use the OpenWrt's upgrade interface to write the sysupgrade
image.
1) Rename openwrt-ramips-mt7621-wavlink_wl-wn531a6-initramfs-kernel.bin
to WN531A6.bin.
2) Connect your computer to the one of the LAN ports of the
router with an Ethernet cable and open http://192.168.10.1
3) Browse to Setup -> Firmware Upgrade interface.
4) Upload the (renamed) OpenWrt image - WN531A6.bin.
5) Proceed with the firmware installation and give the device
a few minutes to finish and reboot.
6) After reboot wait for the "WAVLINK" logo on the top cover
to turn solid blue, and open http://192.168.1.1
7) Use the OpenWrt's "Flash Firmware" interface to write the
OpenWrt sysupgrade image:
openwrt-ramips-mt7621-wavlink_wl-wn531a6-squashfs-sysupgrade.bin
* Flashing instructions (u-boot TFTP):
1) Configure a TFTP server on your computer and set its IP
to 192.168.10.100
2) Rename the OpenWrt sysupgrade image to firmware.bin and
place it in the root folder of the TFTP server.
3) Power off the device and connect an Ethernet cable from
one of its LAN ports your computer.
4) Press the "Reset" button (and keep it pressed)
5) Power on the device.
6) After a few seconds, when the connected port LAN LED stops
blinking fast, release the "Reset" button.
7) Flashing OpenWrt takes less than a minute, system will
reboot automatically.
8) After reboot the WAVLINK logo on the top cover will indicate
the current OpenWrt running status (wait until the logo tunrs
solid blue).
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow "Flashing instructions (u-boot TFTP)" and use the
"firmware.bin" backup image.
* OpenWrt "Flash Firmware" interface:
Upload the "firmware.bin" backup image and select "Force update"
before continuing.
Notes:
-----
* The MAC address shown on the label at the back of the device
is assigned to the 2.4G WiFi adapter.
MAC addresses assigned by the OEM firmware:
2.4G: *:XX (label): factory@0x0004
5G: *:XX + 1 : factory@0x8004
WAN: *:XX - 1 : factory@0xe006
LAN: *:XX - 2 : factory@0xe000
* The I2C bus and UART2 are fully functional. The headers are
not populated.
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
2020-08-25 08:26:21 +00:00
|
|
|
define Device/wavlink_wl-wn531a6
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Wavlink
|
|
|
|
|
DEVICE_MODEL := WL-WN531A6
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware kmod-usb3 -uboot-envtools
|
ramips: add support for Wavlink WL-WN531A6
This patch adds support for Wavlink WL-WN531A6 (Quantum D6).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3, Nanya NT5CB64M16GP-EK
* Flash: 16MB SPI NOR flash, GigaDevice GD25Q127CSIG
* WiFi 5GHz: Mediatek MT7615N (4x4:4) on mini PCIE slot.
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) on mini PCIE slot.
* Ethernet: MT7630, 5x 1000Base-T
* LED: Power, WAN, LAN(x4), WiFi, WPS, dual color
"WAVLINK" LED logo on the top cover.
* Buttons: Reset, WPS, "Turbo", touch button on the top
cover via RH6015C touch sensor.
* UART: UART1: serial console (57600 8n1) on the J4 header
located below the top heatsink.
UART2: J12 header, located on the right side of
the board.
* USB: One USB3 port.
* I2C: J9 header, located below the top heatsink.
Backup the OEM Firmware:
-----------------------
There isn't any firmware released for the WL-WN531A6 on
the Wavlink web site. Reverting back to the OEM firmware is
not possible unless we have a backup of the original OEM
firmware.
The OEM firmware is stored on /dev/mtd4 ("Kernel").
1) Plug a FAT32 formatted USB flash drive into the USB port.
2) Navigate to "Setup->USB Storage". Under the "Available
Network folder" you can see part of the mount point of
the newly mounted flash drive filesystem - e.g "sda1".
The full mount point is prefixed with "/media", so in
this case the mount point becomes "/media/sda1".
3) Go to http://192.168.10.1/webcmd.shtml .
4) Type the following line in the "Command" input box:
dd if=/dev/mtd4ro of=/media/sda1/firmware.bin
5) Click "Apply"
6) After few seconds, in the text area should appear this
output:
30080+0 records in
30080+0 records out
7) Type "sync" in the "Command" input box and click "Apply".
8) At this point the OEM firmware is stored on the flash
drive as "firmware.bin". The size of the file is 15040 KB.
Installation:
------------
* Flashing instructions (OEM web interface):
The OEM web interface accepts only files with names containing
"WN531A6". It's also impossible to flash the *-sysupgrade.bin
image, so we have to flash the *-initramfs-kernel.bin first and
use the OpenWrt's upgrade interface to write the sysupgrade
image.
1) Rename openwrt-ramips-mt7621-wavlink_wl-wn531a6-initramfs-kernel.bin
to WN531A6.bin.
2) Connect your computer to the one of the LAN ports of the
router with an Ethernet cable and open http://192.168.10.1
3) Browse to Setup -> Firmware Upgrade interface.
4) Upload the (renamed) OpenWrt image - WN531A6.bin.
5) Proceed with the firmware installation and give the device
a few minutes to finish and reboot.
6) After reboot wait for the "WAVLINK" logo on the top cover
to turn solid blue, and open http://192.168.1.1
7) Use the OpenWrt's "Flash Firmware" interface to write the
OpenWrt sysupgrade image:
openwrt-ramips-mt7621-wavlink_wl-wn531a6-squashfs-sysupgrade.bin
* Flashing instructions (u-boot TFTP):
1) Configure a TFTP server on your computer and set its IP
to 192.168.10.100
2) Rename the OpenWrt sysupgrade image to firmware.bin and
place it in the root folder of the TFTP server.
3) Power off the device and connect an Ethernet cable from
one of its LAN ports your computer.
4) Press the "Reset" button (and keep it pressed)
5) Power on the device.
6) After a few seconds, when the connected port LAN LED stops
blinking fast, release the "Reset" button.
7) Flashing OpenWrt takes less than a minute, system will
reboot automatically.
8) After reboot the WAVLINK logo on the top cover will indicate
the current OpenWrt running status (wait until the logo tunrs
solid blue).
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow "Flashing instructions (u-boot TFTP)" and use the
"firmware.bin" backup image.
* OpenWrt "Flash Firmware" interface:
Upload the "firmware.bin" backup image and select "Force update"
before continuing.
Notes:
-----
* The MAC address shown on the label at the back of the device
is assigned to the 2.4G WiFi adapter.
MAC addresses assigned by the OEM firmware:
2.4G: *:XX (label): factory@0x0004
5G: *:XX + 1 : factory@0x8004
WAN: *:XX - 1 : factory@0xe006
LAN: *:XX - 2 : factory@0xe000
* The I2C bus and UART2 are fully functional. The headers are
not populated.
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
2020-08-25 08:26:21 +00:00
|
|
|
IMAGE_SIZE := 15040k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wavlink_wl-wn531a6
|
|
|
|
|
|
2022-04-18 15:35:33 +00:00
|
|
|
define Device/wavlink_wl-wn533a8
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Wavlink
|
|
|
|
|
DEVICE_MODEL := WL-WN533A8
|
|
|
|
|
KERNEL_INITRAMFS_SUFFIX := -WN533A8$$(KERNEL_SUFFIX)
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 -uboot-envtools
|
2022-04-18 15:35:33 +00:00
|
|
|
IMAGE_SIZE := 15040k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wavlink_wl-wn533a8
|
|
|
|
|
|
2022-11-30 20:35:30 +00:00
|
|
|
define Device/wavlink_ws-wn572hp3-4g
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := Wavlink
|
|
|
|
|
DEVICE_MODEL := WS-WN572HP3
|
|
|
|
|
DEVICE_VARIANT := 4G
|
|
|
|
|
IMAGE_SIZE := 15040k
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel 0x80001000 | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
|
append-rootfs | pad-rootfs | check-size | append-metadata
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb3 kmod-usb-net-rndis comgt-ncm -uboot-envtools
|
2022-11-30 20:35:30 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wavlink_ws-wn572hp3-4g
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/wevo_11acnas
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2021-02-17 15:06:55 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-10-07 12:33:51 +00:00
|
|
|
UIMAGE_NAME := 11AC-NAS-Router(0.0.0)
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := WeVO
|
|
|
|
|
DEVICE_MODEL := 11AC NAS Router
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-07 14:27:51 +00:00
|
|
|
SUPPORTED_DEVICES += 11acnas
|
2016-04-26 11:43:53 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += wevo_11acnas
|
2016-04-01 07:11:48 +00:00
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/wevo_w2914ns-v2
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2021-02-17 15:06:55 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-10-07 12:33:51 +00:00
|
|
|
UIMAGE_NAME := W2914NS-V2(0.0.0)
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := WeVO
|
|
|
|
|
DEVICE_MODEL := W2914NS
|
|
|
|
|
DEVICE_VARIANT := v2
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += w2914nsv2
|
2016-11-15 11:37:38 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += wevo_w2914ns-v2
|
2016-11-15 11:37:38 +00:00
|
|
|
|
ramips: add support for Sercomm S1500 devices
This commit adds support for following wireless routers:
- Beeline SmartBox PRO (Serсomm S1500 AWI)
- WiFire S1500.NBN (Serсomm S1500 BUC)
This commit is based on this PR:
- Link: https://github.com/openwrt/openwrt/pull/4770
- Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.
My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1
Common specification
--------------------
SoC: MediaTek MT7621AT (880 MHz, 2 cores)
Switch: MediaTek MT7530 (via SoC MT7621AT)
Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe: via J2 on PCB, not soldered on the board
UART: J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek
Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1
WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1
MAC address table (PRO)
-----------------------
use address source
LAN *:23 factory 0x1000 (label)
WAN *:24 factory $label +1
2g *:23 factory $label
5g *:25 factory $label +2
MAC addresses (NBN)
-------------------
use address source
LAN *:0e factory 0x1000
WAN *:0f LAN +1 (label)
2g *:0f LAN +1
5g *:10 LAN +2
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
a. OpenWrt - that's OK, the mission accomplished
b. Stock firmware - install Stock firmware (to switch booflag from
Sercomm0 to Sercomm1) and then OpenWrt factory image.
Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
reboot
2. Install stock firmware via the web OEM firmware interface
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 2d6784a033a994043759fa3b94c48afd5df81f88)
2023-06-11 20:50:23 +00:00
|
|
|
define Device/wifire_s1500-nbn
|
|
|
|
|
$(Device/sercomm_s1500)
|
|
|
|
|
DEVICE_VENDOR := WiFire
|
|
|
|
|
DEVICE_MODEL := S1500.NBN
|
|
|
|
|
DEVICE_ALT0_VENDOR := Sercomm
|
|
|
|
|
DEVICE_ALT0_MODEL := S1500 BUC
|
|
|
|
|
IMAGE_SIZE := 51200k
|
|
|
|
|
IMAGE/factory.img := append-kernel | sercomm-kernel-factory | \
|
|
|
|
|
sercomm-reset-slot1-chksum | append-ubi | check-size | \
|
2023-11-12 07:52:45 +00:00
|
|
|
sercomm-factory-cqr | sercomm-pid-setbit 0x13 | sercomm-mkhash | \
|
ramips: add support for Sercomm S1500 devices
This commit adds support for following wireless routers:
- Beeline SmartBox PRO (Serсomm S1500 AWI)
- WiFire S1500.NBN (Serсomm S1500 BUC)
This commit is based on this PR:
- Link: https://github.com/openwrt/openwrt/pull/4770
- Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.
My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1
Common specification
--------------------
SoC: MediaTek MT7621AT (880 MHz, 2 cores)
Switch: MediaTek MT7530 (via SoC MT7621AT)
Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe: via J2 on PCB, not soldered on the board
UART: J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek
Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1
WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1
MAC address table (PRO)
-----------------------
use address source
LAN *:23 factory 0x1000 (label)
WAN *:24 factory $label +1
2g *:23 factory $label
5g *:25 factory $label +2
MAC addresses (NBN)
-------------------
use address source
LAN *:0e factory 0x1000
WAN *:0f LAN +1 (label)
2g *:0f LAN +1
5g *:10 LAN +2
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
a. OpenWrt - that's OK, the mission accomplished
b. Stock firmware - install Stock firmware (to switch booflag from
Sercomm0 to Sercomm1) and then OpenWrt factory image.
Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
reboot
2. Install stock firmware via the web OEM firmware interface
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 2d6784a033a994043759fa3b94c48afd5df81f88)
2023-06-11 20:50:23 +00:00
|
|
|
sercomm-crypto
|
|
|
|
|
SERCOMM_HWID := BUC
|
|
|
|
|
SERCOMM_HWVER := 10000
|
|
|
|
|
SERCOMM_ROOTFS2_OFFSET := 0x4d00000
|
|
|
|
|
SERCOMM_SWVER := 2015
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wifire_s1500-nbn
|
|
|
|
|
|
ramips: add support for Winstars WS-WN583A6
The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet
ports. Even if mine is branded as "Gemeita AC2100", the sticker on the
back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6.
Probably the real product name is the Wavlink WL-WN583A6 because of
the many references to Wavlink in the OEM firmware and bootlog.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 8MB NOR (GigaDevice GD25Q64B)
ETH: 2x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7603E (2x2:2)
- 5GHz: 1x MT7615E (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x ON/OFF switch (working but unmodifiable)
- 1x Auto/Schedule switch (working but unmodifiable. Read Note #3)
LEDS:
- 1x White led
- 1x Red led
- 1x Amber led
- 1x Blue led
- 2x Blue leds (lan and wan port status: working but unmodifiable)
UART:
- 57600-8-N-1
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M83A6.V5030.191210 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box:
mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done
3) Click "Apply"
4) After few seconds, in the textarea should appear this output:
16384+0 records in
16384+0 records out
8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s
384+0 records in
384+0 records out
196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s
15744+0 records in
15744+0 records out
8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s
dd: can't open '/dev/mtd5ro': No such device
dd: can't open '/dev/mtd6ro': No such device
dd: can't open '/dev/mtd7ro': No such device
Excluding the "X.XXXXXX seconds" part, you should get the same
exact output. If your output doesn't match mine, stop reading
and ask for help in the forum.
5) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd0ro
http://192.168.10.1/dev/mtd1ro
http://192.168.10.1/dev/mtd2ro
http://192.168.10.1/dev/mtd3ro
http://192.168.10.1/dev/mtd4ro
If one (or more) of these files weight 0 byte, stop reading and ask
for help in the forum.
6) Store these downloaded files in a safe place.
7) Reboot your router to remove any temporary file from your router.
Installation
------------
Flash the initramfs image in the OEM firmware interface.
When openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) The "System Command" page allows to run every command as root.
For example you can use "dd" and "nc" to backup the OEM firmware.
PC (SERVER):
nc -l 5555 > ./mtdXro
ROUTER (CLIENT):
dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555
2) The OEM web interface accepts only images containing the string
"WN583A6" in the filename.
Currently the OEM interface accepts only the initramfs image
probably because it checks if the ih_size in the image header is
equal to the whole image size (instead of the kernel size)
Read more here:
https://forum.openwrt.org/t/support-for-strong-1200/22768/19
3) The white led (namely "Smart Night Light") can be controller by the
user only if the side switch is set to "Schedule" otherwise it will
be activated by the light condition (there is a photodiode on the
top side of the router)
4) Router mac addresses:
LAN XX:XX:XX:XX:XX:8F
WAN XX:XX:XX:XX:XX:90
WIFI 2G XX:XX:XX:XX:XX:91
WIFI 5G XX:XX:XX:XX:XX:92
LABEL XX:XX:XX:XX:XX:91
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove chosen node, fix whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 21:29:27 +00:00
|
|
|
define Device/winstars_ws-wn583a6
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
ramips: add support for Winstars WS-WN583A6
The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet
ports. Even if mine is branded as "Gemeita AC2100", the sticker on the
back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6.
Probably the real product name is the Wavlink WL-WN583A6 because of
the many references to Wavlink in the OEM firmware and bootlog.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 8MB NOR (GigaDevice GD25Q64B)
ETH: 2x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7603E (2x2:2)
- 5GHz: 1x MT7615E (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x ON/OFF switch (working but unmodifiable)
- 1x Auto/Schedule switch (working but unmodifiable. Read Note #3)
LEDS:
- 1x White led
- 1x Red led
- 1x Amber led
- 1x Blue led
- 2x Blue leds (lan and wan port status: working but unmodifiable)
UART:
- 57600-8-N-1
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M83A6.V5030.191210 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box:
mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done
3) Click "Apply"
4) After few seconds, in the textarea should appear this output:
16384+0 records in
16384+0 records out
8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s
384+0 records in
384+0 records out
196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s
15744+0 records in
15744+0 records out
8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s
dd: can't open '/dev/mtd5ro': No such device
dd: can't open '/dev/mtd6ro': No such device
dd: can't open '/dev/mtd7ro': No such device
Excluding the "X.XXXXXX seconds" part, you should get the same
exact output. If your output doesn't match mine, stop reading
and ask for help in the forum.
5) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd0ro
http://192.168.10.1/dev/mtd1ro
http://192.168.10.1/dev/mtd2ro
http://192.168.10.1/dev/mtd3ro
http://192.168.10.1/dev/mtd4ro
If one (or more) of these files weight 0 byte, stop reading and ask
for help in the forum.
6) Store these downloaded files in a safe place.
7) Reboot your router to remove any temporary file from your router.
Installation
------------
Flash the initramfs image in the OEM firmware interface.
When openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) The "System Command" page allows to run every command as root.
For example you can use "dd" and "nc" to backup the OEM firmware.
PC (SERVER):
nc -l 5555 > ./mtdXro
ROUTER (CLIENT):
dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555
2) The OEM web interface accepts only images containing the string
"WN583A6" in the filename.
Currently the OEM interface accepts only the initramfs image
probably because it checks if the ih_size in the image header is
equal to the whole image size (instead of the kernel size)
Read more here:
https://forum.openwrt.org/t/support-for-strong-1200/22768/19
3) The white led (namely "Smart Night Light") can be controller by the
user only if the side switch is set to "Schedule" otherwise it will
be activated by the light condition (there is a photodiode on the
top side of the router)
4) Router mac addresses:
LAN XX:XX:XX:XX:XX:8F
WAN XX:XX:XX:XX:XX:90
WIFI 2G XX:XX:XX:XX:XX:91
WIFI 5G XX:XX:XX:XX:XX:92
LABEL XX:XX:XX:XX:XX:91
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove chosen node, fix whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 21:29:27 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 7872k
|
|
|
|
|
DEVICE_VENDOR := Winstars
|
|
|
|
|
DEVICE_MODEL := WS-WN583A6
|
|
|
|
|
DEVICE_ALT0_VENDOR := Gemeita
|
|
|
|
|
DEVICE_ALT0_MODEL := AC2100
|
|
|
|
|
KERNEL_INITRAMFS_SUFFIX := -WN583A6$$(KERNEL_SUFFIX)
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615-firmware -uboot-envtools
|
ramips: add support for Winstars WS-WN583A6
The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet
ports. Even if mine is branded as "Gemeita AC2100", the sticker on the
back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6.
Probably the real product name is the Wavlink WL-WN583A6 because of
the many references to Wavlink in the OEM firmware and bootlog.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 8MB NOR (GigaDevice GD25Q64B)
ETH: 2x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7603E (2x2:2)
- 5GHz: 1x MT7615E (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x ON/OFF switch (working but unmodifiable)
- 1x Auto/Schedule switch (working but unmodifiable. Read Note #3)
LEDS:
- 1x White led
- 1x Red led
- 1x Amber led
- 1x Blue led
- 2x Blue leds (lan and wan port status: working but unmodifiable)
UART:
- 57600-8-N-1
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M83A6.V5030.191210 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box:
mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done
3) Click "Apply"
4) After few seconds, in the textarea should appear this output:
16384+0 records in
16384+0 records out
8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s
384+0 records in
384+0 records out
196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s
128+0 records in
128+0 records out
65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s
15744+0 records in
15744+0 records out
8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s
dd: can't open '/dev/mtd5ro': No such device
dd: can't open '/dev/mtd6ro': No such device
dd: can't open '/dev/mtd7ro': No such device
Excluding the "X.XXXXXX seconds" part, you should get the same
exact output. If your output doesn't match mine, stop reading
and ask for help in the forum.
5) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd0ro
http://192.168.10.1/dev/mtd1ro
http://192.168.10.1/dev/mtd2ro
http://192.168.10.1/dev/mtd3ro
http://192.168.10.1/dev/mtd4ro
If one (or more) of these files weight 0 byte, stop reading and ask
for help in the forum.
6) Store these downloaded files in a safe place.
7) Reboot your router to remove any temporary file from your router.
Installation
------------
Flash the initramfs image in the OEM firmware interface.
When openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) The "System Command" page allows to run every command as root.
For example you can use "dd" and "nc" to backup the OEM firmware.
PC (SERVER):
nc -l 5555 > ./mtdXro
ROUTER (CLIENT):
dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555
2) The OEM web interface accepts only images containing the string
"WN583A6" in the filename.
Currently the OEM interface accepts only the initramfs image
probably because it checks if the ih_size in the image header is
equal to the whole image size (instead of the kernel size)
Read more here:
https://forum.openwrt.org/t/support-for-strong-1200/22768/19
3) The white led (namely "Smart Night Light") can be controller by the
user only if the side switch is set to "Schedule" otherwise it will
be activated by the light condition (there is a photodiode on the
top side of the router)
4) Router mac addresses:
LAN XX:XX:XX:XX:XX:8F
WAN XX:XX:XX:XX:XX:90
WIFI 2G XX:XX:XX:XX:XX:91
WIFI 5G XX:XX:XX:XX:XX:92
LABEL XX:XX:XX:XX:XX:91
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove chosen node, fix whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 21:29:27 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += winstars_ws-wn583a6
|
|
|
|
|
|
2021-01-19 17:34:21 +00:00
|
|
|
define Device/xiaomi_nand_separate
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2020-05-30 09:18:50 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2021-01-19 17:34:21 +00:00
|
|
|
DEVICE_VENDOR := Xiaomi
|
2020-05-30 09:18:50 +00:00
|
|
|
IMAGES += kernel1.bin rootfs0.bin
|
|
|
|
|
IMAGE/kernel1.bin := append-kernel
|
|
|
|
|
IMAGE/rootfs0.bin := append-ubi | check-size
|
|
|
|
|
endef
|
|
|
|
|
|
2020-12-08 14:05:47 +00:00
|
|
|
define Device/xiaomi_mi-router-3g
|
2021-01-19 17:34:21 +00:00
|
|
|
$(Device/xiaomi_nand_separate)
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_MODEL := Mi Router 3G
|
2021-01-19 17:34:21 +00:00
|
|
|
IMAGE_SIZE := 124416k
|
|
|
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2020-12-08 14:05:47 +00:00
|
|
|
SUPPORTED_DEVICES += R3G mir3g xiaomi,mir3g
|
2016-04-01 07:11:48 +00:00
|
|
|
endef
|
2020-12-08 14:05:47 +00:00
|
|
|
TARGET_DEVICES += xiaomi_mi-router-3g
|
2018-05-03 15:59:27 +00:00
|
|
|
|
2020-12-08 14:05:47 +00:00
|
|
|
define Device/xiaomi_mi-router-3g-v2
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-04-15 01:32:02 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-10-25 10:18:43 +00:00
|
|
|
IMAGE_SIZE := 14848k
|
|
|
|
|
DEVICE_VENDOR := Xiaomi
|
|
|
|
|
DEVICE_MODEL := Mi Router 3G
|
|
|
|
|
DEVICE_VARIANT := v2
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 -uboot-envtools
|
2020-12-08 14:05:47 +00:00
|
|
|
SUPPORTED_DEVICES += xiaomi,mir3g-v2
|
2019-10-25 10:18:43 +00:00
|
|
|
endef
|
2020-12-08 14:05:47 +00:00
|
|
|
TARGET_DEVICES += xiaomi_mi-router-3g-v2
|
2019-10-25 10:18:43 +00:00
|
|
|
|
2020-12-08 14:05:47 +00:00
|
|
|
define Device/xiaomi_mi-router-3-pro
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2020-04-15 01:32:02 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-15 12:55:24 +00:00
|
|
|
IMAGE_SIZE := 255488k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := Xiaomi
|
|
|
|
|
DEVICE_MODEL := Mi Router 3 Pro
|
|
|
|
|
IMAGES += factory.bin
|
2019-12-19 18:40:33 +00:00
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
2020-03-10 13:58:27 +00:00
|
|
|
check-size
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 kmod-usb-ledtrig-usbport
|
2020-12-08 14:05:47 +00:00
|
|
|
SUPPORTED_DEVICES += xiaomi,mir3p
|
2018-05-03 15:59:27 +00:00
|
|
|
endef
|
2020-12-08 14:05:47 +00:00
|
|
|
TARGET_DEVICES += xiaomi_mi-router-3-pro
|
2016-04-01 07:11:48 +00:00
|
|
|
|
ramips: mt7621: add support for Xiaomi Mi Router 4
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).
Specifications:
Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A
UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it
MAC addresses as verified by OEM firmware:
use address source
LAN *:c2 factory 0xe000 (label)
WAN *:c3 factory 0xe006
2g *:c4 factory 0x0000
5g *:c5 factory 0x8000
Flashing instructions:
1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:
setenv uart_en 1
saveenv
boot
3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/
Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion
Signed-off-by: Dmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-14 19:07:32 +00:00
|
|
|
define Device/xiaomi_mi-router-4
|
|
|
|
|
$(Device/xiaomi_nand_separate)
|
|
|
|
|
DEVICE_MODEL := Mi Router 4
|
|
|
|
|
IMAGE_SIZE := 124416k
|
|
|
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt76x2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaomi_mi-router-4
|
|
|
|
|
|
2020-11-12 15:00:10 +00:00
|
|
|
define Device/xiaomi_mi-router-4a-gigabit
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 14848k
|
|
|
|
|
DEVICE_VENDOR := Xiaomi
|
|
|
|
|
DEVICE_MODEL := Mi Router 4A
|
|
|
|
|
DEVICE_VARIANT := Gigabit Edition
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 -uboot-envtools
|
2020-11-12 15:00:10 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaomi_mi-router-4a-gigabit
|
|
|
|
|
|
2023-01-15 21:52:27 +00:00
|
|
|
define Device/xiaomi_mi-router-4a-gigabit-v2
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 14784k
|
|
|
|
|
DEVICE_VENDOR := Xiaomi
|
|
|
|
|
DEVICE_MODEL := Mi Router 4A
|
|
|
|
|
DEVICE_VARIANT := Gigabit Edition v2
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
|
|
|
|
-uboot-envtools
|
2023-01-15 21:52:27 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaomi_mi-router-4a-gigabit-v2
|
|
|
|
|
|
2020-12-08 14:05:47 +00:00
|
|
|
define Device/xiaomi_mi-router-ac2100
|
2021-01-19 17:34:21 +00:00
|
|
|
$(Device/xiaomi_nand_separate)
|
2020-12-08 14:05:47 +00:00
|
|
|
DEVICE_MODEL := Mi Router AC2100
|
2021-01-19 17:34:21 +00:00
|
|
|
IMAGE_SIZE := 120320k
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615-firmware -uboot-envtools
|
2020-12-08 14:05:47 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaomi_mi-router-ac2100
|
|
|
|
|
|
ramips: add support for Xiaomi Mi Router CR660x series
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
2021-09-11 15:54:30 +00:00
|
|
|
define Device/xiaomi_mi-router-cr660x
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: add support for Xiaomi Mi Router CR660x series
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
2021-09-11 15:54:30 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
DEVICE_VENDOR := Xiaomi
|
|
|
|
|
IMAGE_SIZE := 128512k
|
|
|
|
|
IMAGES += firmware.bin
|
|
|
|
|
IMAGE/firmware.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
|
|
|
|
|
check-size
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7915-firmware
|
ramips: add support for Xiaomi Mi Router CR660x series
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
2021-09-11 15:54:30 +00:00
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/xiaomi_mi-router-cr6606
|
|
|
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
|
|
|
DEVICE_MODEL := Mi Router CR6606
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6606
|
|
|
|
|
|
|
|
|
|
define Device/xiaomi_mi-router-cr6608
|
|
|
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
|
|
|
DEVICE_MODEL := Mi Router CR6608
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6608
|
|
|
|
|
|
|
|
|
|
define Device/xiaomi_mi-router-cr6609
|
|
|
|
|
$(Device/xiaomi_mi-router-cr660x)
|
|
|
|
|
DEVICE_MODEL := Mi Router CR6609
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaomi_mi-router-cr6609
|
|
|
|
|
|
2020-04-23 02:50:21 +00:00
|
|
|
define Device/xiaomi_redmi-router-ac2100
|
2021-01-19 17:34:21 +00:00
|
|
|
$(Device/xiaomi_nand_separate)
|
2020-04-23 02:50:21 +00:00
|
|
|
DEVICE_MODEL := Redmi Router AC2100
|
2021-01-19 17:34:21 +00:00
|
|
|
IMAGE_SIZE := 120320k
|
2022-12-17 12:50:55 +00:00
|
|
|
DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615-firmware
|
2020-04-23 02:50:21 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaomi_redmi-router-ac2100
|
|
|
|
|
|
2019-09-08 01:52:07 +00:00
|
|
|
define Device/xiaoyu_xy-c5
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-09-08 01:52:07 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
|
|
|
|
DEVICE_VENDOR := XiaoYu
|
|
|
|
|
DEVICE_MODEL := XY-C5
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-usb3 -wpad-basic-mbedtls \
|
|
|
|
|
-uboot-envtools
|
2019-09-08 01:52:07 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += xiaoyu_xy-c5
|
|
|
|
|
|
2019-07-07 14:27:51 +00:00
|
|
|
define Device/xzwifi_creativebox-v1
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
2019-07-07 14:27:51 +00:00
|
|
|
DEVICE_VENDOR := CreativeBox
|
|
|
|
|
DEVICE_MODEL := v1
|
2020-03-05 13:57:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-mt7603 kmod-mt76x2 kmod-sdhci-mt7620 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb3 -wpad-basic-mbedtls -uboot-envtools
|
2016-05-10 16:17:54 +00:00
|
|
|
endef
|
2019-07-07 14:27:51 +00:00
|
|
|
TARGET_DEVICES += xzwifi_creativebox-v1
|
2016-05-10 16:17:54 +00:00
|
|
|
|
2018-03-29 10:33:02 +00:00
|
|
|
define Device/youhua_wr1200js
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2018-03-29 10:33:02 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := YouHua
|
|
|
|
|
DEVICE_MODEL := WR1200JS
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2018-03-29 10:33:02 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += youhua_wr1200js
|
|
|
|
|
|
2019-03-11 16:21:58 +00:00
|
|
|
define Device/youku_yk-l2
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_VENDOR := Youku
|
|
|
|
|
DEVICE_MODEL := YK-L2
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2022-11-05 11:52:08 +00:00
|
|
|
UIMAGE_MAGIC := 0x12291000
|
|
|
|
|
UIMAGE_NAME := 400000000000000000003000
|
2019-03-11 16:21:58 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += youku_yk-l2
|
|
|
|
|
|
2021-07-22 15:54:15 +00:00
|
|
|
define Device/yuncore_ax820
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
|
DEVICE_VENDOR := YunCore
|
|
|
|
|
DEVICE_MODEL := AX820
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
2021-07-22 15:54:15 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += yuncore_ax820
|
|
|
|
|
|
ramips: add support for YunCore FAP640
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI
- Wi-Fi:
- MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN
- UART: J4 (115200 baud)
- Pinout: [3V3] (TXD) (RXD) (GND)
- Power: 802.11af/at PoE;
- Bootloader: U-Boot
- Buttons:
- Reset
- LEDs:
- Status - RGB controlled by
- GPIO 14 LOW - green color
- GPIO 15 LOW- red color
- GPIO 16 LOW - blue color
- WAN - gren color, controlled by switch GPIO 12 LOW
- LAN1 - gren color, controlled by switch GPIO 9 HIGH
- LAN2 - gren color, controlled by switch GPIO 6 LOW
- LAN3 - gren color, controlled by switch GPIO 3 LOW
- LAN4 - gren color, controlled by switch GPIO 0 LOW
Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
router will not boot.
MAC addresses with OEM firmware:
vendor source
lan factory 0x4 (label)
5g factory 0x4 (label)
2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
4-th byte
Example
label: 44:xx:xx:b7:xx:xx
lan: 44:xx:xx:b7:xx:xx
2g 46:xx:xx:c7:xx:xx
5g 44:xx:xx:b7:xx:xx
Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2022-10-19 20:05:16 +00:00
|
|
|
define Device/yuncore_fap640
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
|
DEVICE_VENDOR := YunCore
|
|
|
|
|
DEVICE_MODEL := FAP640
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
ramips: add support for YunCore FAP640
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI
- Wi-Fi:
- MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN
- UART: J4 (115200 baud)
- Pinout: [3V3] (TXD) (RXD) (GND)
- Power: 802.11af/at PoE;
- Bootloader: U-Boot
- Buttons:
- Reset
- LEDs:
- Status - RGB controlled by
- GPIO 14 LOW - green color
- GPIO 15 LOW- red color
- GPIO 16 LOW - blue color
- WAN - gren color, controlled by switch GPIO 12 LOW
- LAN1 - gren color, controlled by switch GPIO 9 HIGH
- LAN2 - gren color, controlled by switch GPIO 6 LOW
- LAN3 - gren color, controlled by switch GPIO 3 LOW
- LAN4 - gren color, controlled by switch GPIO 0 LOW
Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
router will not boot.
MAC addresses with OEM firmware:
vendor source
lan factory 0x4 (label)
5g factory 0x4 (label)
2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
4-th byte
Example
label: 44:xx:xx:b7:xx:xx
lan: 44:xx:xx:b7:xx:xx
2g 46:xx:xx:c7:xx:xx
5g 44:xx:xx:b7:xx:xx
Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2022-10-19 20:05:16 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += yuncore_fap640
|
|
|
|
|
|
2022-06-22 12:41:36 +00:00
|
|
|
define Device/yuncore_fap690
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
|
DEVICE_VENDOR := YunCore
|
|
|
|
|
DEVICE_MODEL := FAP690
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
|
2022-06-22 12:41:36 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += yuncore_fap690
|
|
|
|
|
|
2024-03-08 20:20:23 +00:00
|
|
|
define Device/yuncore_g720
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
DEVICE_VENDOR := YunCore
|
|
|
|
|
DEVICE_MODEL := G720
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
|
SUPPORTED_DEVICES += mt7621-rfb-ax-nor
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += yuncore_g720
|
|
|
|
|
|
ramips: add support for Z-ROUTER ZR-2660
This commit adds support for Z-ROUTER ZR-2660 (also known as Routerich
AX1800) wireless WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (AMD/Spansion S34ML01G2)
- WLAN :
- 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2
- 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- USB : 1x 2.0
- UART : 3.3V, 115200n8, pins are silkscreened on the pcb
- Buttons : 1x Reset
- LEDs : 1x WiFi 2.4 GHz (green)
1x WiFi 5 GHz (green)
1x LAN (green)
1x WAN (green)
1x WAN no-internet (red)
- Power : 12 VDC, 1 A
Installation
------------
1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs
image (initramfs.bin) to the tftp root dir
2. Open the following link in the browser to enable telnet:
http://192.168.2.1/cgi-bin/telnet_ssh
3. Connect to the router (default IP: 192.168.2.1) using telnet shell
(credentials - user:admin)
4. Run the following commands in the telnet shell (this will install
OpenWrt initramfs image on nand flash):
cd /tmp
tftp -g -r initramfs.bin 192.168.2.2
mtd write initramfs.bin firmware
mtd erase firmware_backup
reboot
5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the
router
6. Connect to the router (IP: 192.168.1.1) using ssh shell and run
sysupgrade command:
sysupgrade -n /tmp/sysupgrade.bin
Return to stock
---------------
1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp
2. Run following command in the router shell:
cd /tmp
mtd write stock.bin firmware
reboot
Recovery
--------
Connect uart (pins are silkscreened on the pcb), interrupt boot process by
pressing any key, use u-boot menu to flash stock firmware image or OpenWrt
initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 24:0f:5e:xx:xx:4c | label |
| WAN | 24:0f:5e:xx:xx:4d | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 |
+---------+-------------------+-----------+
The WLAN 2.4 MAC was found in 'factory', 0x4
The LAN MAC was found in 'factory', 0xfff4
The WAN MAC was found in 'factory', 0xfffa
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 1d3d6ef8269aca7ee34fb6ddd1c11d3fe45e785b)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2024-03-02 19:58:40 +00:00
|
|
|
define Device/z-router_zr-2660
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/nand)
|
|
|
|
|
DEVICE_VENDOR := Z-ROUTER
|
|
|
|
|
DEVICE_MODEL := ZR-2660
|
|
|
|
|
DEVICE_ALT0_VENDOR := Routerich
|
|
|
|
|
DEVICE_ALT0_MODEL := AX1800
|
|
|
|
|
IMAGE_SIZE := 90112k
|
|
|
|
|
KERNEL_LOADADDR := 0x82000000
|
|
|
|
|
KERNEL := kernel-bin | relocate-kernel $(loadaddr-y) | lzma | \
|
|
|
|
|
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
DEVICE_PACKAGES += kmod-mt7915-firmware kmod-usb3 -uboot-envtools
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += z-router_zr-2660
|
|
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/zbtlink_zbt-we1326
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2021-01-27 12:26:23 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-09-26 12:44:22 +00:00
|
|
|
DEVICE_VENDOR := Zbtlink
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_MODEL := ZBT-WE1326
|
2023-02-19 01:06:32 +00:00
|
|
|
DEVICE_ALT0_VENDOR := Wiflyer
|
|
|
|
|
DEVICE_ALT0_MODEL := WF3526-P
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-sdhci-mt7620 \
|
|
|
|
|
-uboot-envtools
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += zbt-we1326
|
2017-04-20 03:07:26 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += zbtlink_zbt-we1326
|
2017-04-20 03:07:26 +00:00
|
|
|
|
2017-12-16 23:30:21 +00:00
|
|
|
define Device/zbtlink_zbt-we3526
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2021-01-27 12:26:23 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-09-26 12:44:22 +00:00
|
|
|
DEVICE_VENDOR := Zbtlink
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_MODEL := ZBT-WE3526
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2017-11-07 12:17:06 +00:00
|
|
|
endef
|
2017-12-16 23:30:21 +00:00
|
|
|
TARGET_DEVICES += zbtlink_zbt-we3526
|
2017-11-07 12:17:06 +00:00
|
|
|
|
2021-11-16 10:10:25 +00:00
|
|
|
define Device/zbtlink_zbt-wg1602-16m
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := Zbtlink
|
|
|
|
|
DEVICE_MODEL := ZBT-WG1602
|
|
|
|
|
DEVICE_VARIANT := 16M
|
|
|
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2021-11-16 10:10:25 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zbtlink_zbt-wg1602-16m
|
|
|
|
|
|
ramips: add support for Zbtlink ZBT-WG1602-V04
Description heavily based on commit
7e89421a7c3855d66a20350a5bf9ca4cc7a2caf9 by
Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have
been removed
Completed with great help from \x on IRC. Thanks, \x!
Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe
slots with USB and SIM only and another one which is a pure miniPCIe
slot as well as five Gigabit Ethernet ports (4xLAN + WAN).
Specification:
* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2)
* WLAN 5GHz: MT7662E (.11nac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 3.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled,
1 power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)
Additional HW information:
* SoC USB port 1 is shared by internal miniPCIe slot and external
Type-A USB port, USB D+/D- lines are toggled between ports using a
GPIO controlled DPDT switch.
Installation:
The kernel image can be installed directly onto the device via a browser
to 192.168.1.1 using the built in firmware recovery Web UI available.
It can be accessed by pushing the reset button in, applying power and
holding the reset button for approximately 10 seconds. When the kernel
image has been flashed, you can access LuCI and upload the sysupgrade
as normal.
Signed-off-by: Alexander Horner <ahorner@programmer.net>
2022-09-26 19:17:40 +00:00
|
|
|
define Device/zbtlink_zbt-wg1602-v04-16m
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := Zbtlink
|
|
|
|
|
DEVICE_MODEL := ZBT-WG1602-V04
|
|
|
|
|
DEVICE_VARIANT := 16M
|
|
|
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
ramips: add support for Zbtlink ZBT-WG1602-V04
Description heavily based on commit
7e89421a7c3855d66a20350a5bf9ca4cc7a2caf9 by
Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have
been removed
Completed with great help from \x on IRC. Thanks, \x!
Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe
slots with USB and SIM only and another one which is a pure miniPCIe
slot as well as five Gigabit Ethernet ports (4xLAN + WAN).
Specification:
* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2)
* WLAN 5GHz: MT7662E (.11nac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 3.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled,
1 power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)
Additional HW information:
* SoC USB port 1 is shared by internal miniPCIe slot and external
Type-A USB port, USB D+/D- lines are toggled between ports using a
GPIO controlled DPDT switch.
Installation:
The kernel image can be installed directly onto the device via a browser
to 192.168.1.1 using the built in firmware recovery Web UI available.
It can be accessed by pushing the reset button in, applying power and
holding the reset button for approximately 10 seconds. When the kernel
image has been flashed, you can access LuCI and upload the sysupgrade
as normal.
Signed-off-by: Alexander Horner <ahorner@programmer.net>
2022-09-26 19:17:40 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zbtlink_zbt-wg1602-v04-16m
|
|
|
|
|
|
|
|
|
|
define Device/zbtlink_zbt-wg1602-v04-32m
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 32128k
|
|
|
|
|
DEVICE_VENDOR := Zbtlink
|
|
|
|
|
DEVICE_MODEL := ZBT-WG1602-V04
|
|
|
|
|
DEVICE_VARIANT := 32M
|
|
|
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
ramips: add support for Zbtlink ZBT-WG1602-V04
Description heavily based on commit
7e89421a7c3855d66a20350a5bf9ca4cc7a2caf9 by
Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have
been removed
Completed with great help from \x on IRC. Thanks, \x!
Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe
slots with USB and SIM only and another one which is a pure miniPCIe
slot as well as five Gigabit Ethernet ports (4xLAN + WAN).
Specification:
* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2)
* WLAN 5GHz: MT7662E (.11nac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 3.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled,
1 power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)
Additional HW information:
* SoC USB port 1 is shared by internal miniPCIe slot and external
Type-A USB port, USB D+/D- lines are toggled between ports using a
GPIO controlled DPDT switch.
Installation:
The kernel image can be installed directly onto the device via a browser
to 192.168.1.1 using the built in firmware recovery Web UI available.
It can be accessed by pushing the reset button in, applying power and
holding the reset button for approximately 10 seconds. When the kernel
image has been flashed, you can access LuCI and upload the sysupgrade
as normal.
Signed-off-by: Alexander Horner <ahorner@programmer.net>
2022-09-26 19:17:40 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zbtlink_zbt-wg1602-v04-32m
|
|
|
|
|
|
2022-02-23 15:14:37 +00:00
|
|
|
define Device/zbtlink_zbt-wg1608-16m
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := Zbtlink
|
|
|
|
|
DEVICE_MODEL := ZBT-WG1608
|
|
|
|
|
DEVICE_VARIANT := 16M
|
|
|
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt7615e \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-mt7663-firmware-ap kmod-usb3 kmod-usb-ledtrig-usbport \
|
|
|
|
|
-uboot-envtools
|
2022-02-23 15:14:37 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zbtlink_zbt-wg1608-16m
|
|
|
|
|
|
2022-08-11 08:13:35 +00:00
|
|
|
define Device/zbtlink_zbt-wg1608-32m
|
|
|
|
|
$(Device/dsa-migration)
|
|
|
|
|
$(Device/uimage-lzma-loader)
|
|
|
|
|
IMAGE_SIZE := 32448k
|
|
|
|
|
DEVICE_VENDOR := Zbtlink
|
|
|
|
|
DEVICE_MODEL := ZBT-WG1608
|
|
|
|
|
DEVICE_VARIANT := 32M
|
|
|
|
|
DEVICE_PACKAGES := kmod-sdhci-mt7620 kmod-mt7603 kmod-mt7615e \
|
|
|
|
|
kmod-mt7663-firmware-ap kmod-usb3 kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zbtlink_zbt-wg1608-32m
|
|
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/zbtlink_zbt-wg2626
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2021-01-27 12:26:23 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-09-26 12:44:22 +00:00
|
|
|
DEVICE_VENDOR := Zbtlink
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_MODEL := ZBT-WG2626
|
2020-03-05 13:57:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += zbt-wg2626
|
2016-11-18 11:46:27 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += zbtlink_zbt-wg2626
|
2016-11-18 11:46:27 +00:00
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/zbtlink_zbt-wg3526-16m
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-08-23 10:02:48 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
2019-09-26 12:44:22 +00:00
|
|
|
DEVICE_VENDOR := Zbtlink
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_MODEL := ZBT-WG3526
|
|
|
|
|
DEVICE_VARIANT := 16M
|
2020-03-05 13:57:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb3 kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += zbt-wg3526 zbt-wg3526-16M
|
2016-11-18 11:46:27 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += zbtlink_zbt-wg3526-16m
|
2016-11-18 11:46:27 +00:00
|
|
|
|
2019-07-03 21:22:08 +00:00
|
|
|
define Device/zbtlink_zbt-wg3526-32m
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2020-08-23 10:02:48 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
2019-07-22 16:09:57 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
2019-09-26 12:44:22 +00:00
|
|
|
DEVICE_VENDOR := Zbtlink
|
2019-07-06 12:51:09 +00:00
|
|
|
DEVICE_MODEL := ZBT-WG3526
|
|
|
|
|
DEVICE_VARIANT := 32M
|
2020-03-05 13:57:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt7603 kmod-mt76x2 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb3 kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-07-03 21:22:08 +00:00
|
|
|
SUPPORTED_DEVICES += ac1200pro zbt-wg3526-32M
|
2017-04-01 08:46:44 +00:00
|
|
|
endef
|
2019-07-03 21:22:08 +00:00
|
|
|
TARGET_DEVICES += zbtlink_zbt-wg3526-32m
|
2019-11-11 16:26:44 +00:00
|
|
|
|
|
|
|
|
define Device/zio_freezio
|
2020-07-14 14:42:40 +00:00
|
|
|
$(Device/dsa-migration)
|
2019-11-11 16:26:44 +00:00
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_VENDOR := ZIO
|
|
|
|
|
DEVICE_MODEL := FREEZIO
|
2019-12-19 18:40:33 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
|
2023-02-28 11:39:36 +00:00
|
|
|
kmod-usb-ledtrig-usbport -uboot-envtools
|
2019-11-11 16:26:44 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zio_freezio
|
ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)
Hardware
--------
SoC: MediaTek MT7621ST
WiFi: MediaTek MT7603
Quantenna QT3840BC
Flash: 128M NAND
RAM: 64M
LED: Dual colour red and green
BTN: Reset
WPS
Eth: 4 x 10/100/1000 connected to MT7621 internal switch
MT7621 RGMII port connected to Quantenna module
GPIO: Power/reset of Quantenna module
Quantenna module
----------------
The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation. It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621. It loads both a second uboot stage and an os
image from the MT7621 using tftp. The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.
There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.
Serial ports
------------
Two serial ports with headers:
RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1 - 57600 8N1 - Connected to the MT7621 console
Both share pinout with many other Zyxel/Mitrastar devices:
1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND
Dual system partitions
----------------------
The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.
OpenWrt does not support this scheme and will always use the
first OS partition. It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.
Installation from vendor firmware
---------------------------------
1. Run a DHCP server. The WAP6805 is configured as a client device
and does not have a default static IP address. Make a note of
which address it is assigned
2. tftp the OpenWrt initramfs-kernel.bin image to this address.
Wait for the WAP6805 to reboot.
3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
backup of all mtd partitions now. The last used OEM image is
still present in either "Kernel" or "Kernel2" at this point,
and can be restored later if you save a copy.
4. sysupgrade to the OpenWrt sysupgrade.bin image.
Installation from U-Boot
------------------------
This requires serial console access
1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
your tftp server directory. Configure the server address as
192.168.0.33/24
2. Hit ESC when the message "Hit ESC key to stop autoboot"
appears
3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.
4. Answer Y to the question "Erase Linux in Flash then burn new
one. Are you sure?", and answer the address/filename questions.
Defaults:
Input device IP (192.168.0.2)
Input server IP (192.168.0.33)
Input Linux Kernel filename ("ras.bin")
5. Wait until after you see the message "Done!" and power cycle
the device. It will hang after flashing.
6. Continue with step 3 and 4 from the vendor firmware procedure.
Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme. These changes appear to have
broken a few things. The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work. The image selection
scheme is unreliable and inconsistent. A limited U-Boot menu is
available - and used by the above U-Boot install procedure. But
direct booting into an uploaded image does not work, neither with
ram nor with flash. Flashing works, but requires a hard reset after
it is finished.
Reverting to OEM firmware
-------------------------
The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.
ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin
OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required. See above.
Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware. But the branding features do obviously
differ.
LED controller
--------------
Hardware implementation is unknown. The dual-color LED is controlled
by 3 GPIOs:
4: red
7: blinking green
13: green
Enabling both red and green makes the LED appear yellow.
The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-04-18 19:57:52 +00:00
|
|
|
|
2022-06-17 19:35:03 +00:00
|
|
|
define Device/zyxel_lte3301-plus
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-06-17 19:35:03 +00:00
|
|
|
DEVICE_VENDOR := ZyXEL
|
|
|
|
|
DEVICE_MODEL := LTE3301-PLUS
|
2023-05-13 13:01:00 +00:00
|
|
|
KERNEL_SIZE := 31488k
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7615-firmware kmod-usb3 kmod-usb-ledtrig-usbport \
|
|
|
|
|
kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
2022-06-17 19:35:03 +00:00
|
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma | \
|
|
|
|
|
zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
|
|
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | \
|
|
|
|
|
zytrx-header $$(DEVICE_MODEL) 9.99(ABQU.1)$$(VERSION_DIST)-recovery
|
|
|
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.bin
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_lte3301-plus
|
|
|
|
|
|
ramips: mt7621: Add support for ZyXEL NR7101
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E
- Switch: 1 LAN port (Gigabiti)
- 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
- SIM: 2 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/yellow under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable. Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.
A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.
MAC addresses:
OpenWrt OEM Address Found as
lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label
wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex)
wwan0 usb0 random
WARNING!!
ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled. Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.
Installation from OEM web GUI:
- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Installation from OEM ssh:
- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
nvram setro uboot DebugFlag 0x1
nvram setro uboot CheckBypass 0
nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Copying OpenWrt to the recovery partition:
- Verify that you are running a working OpenWrt recovery image
from flash
- ssh to root@192.168.1.1 and run:
fw_setenv CheckBypass 0
mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2
NOTE: This should only be done after successfully booting the OpenWrt
recovery image from the primary partition during installation. Do
not do this after having sysupgraded OpenWrt! Reinstalling the
recovery image on normal upgrades is not required or recommended.
Installation from Z-Loader:
- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image
NOTE: ATNR will write the recovery image to both primary and recovery
partitions in one go.
Booting from RAM:
- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
header
This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies! Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.
NOTE: U-Boot configuration is incomplete (on some devices?). You may
have to configure a working mac address before running tftp using
"setenv eth0addr <mac>"
Unlocking the bootloader:
If you are unebale to halt boot, then the bootloader is locked.
The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0. Setting it to 1 is therefore only temporary
when OEM firmware is installed.
- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt
NOTE:
OpenWrt does this automatically on first boot if necessary
NOTE2:
Setting the flag to 0x1 avoids the reset to 0 in known OEM
versions, but this might change.
WARNING:
Writing anything to flash while the bootloader is locked is
considered extremely risky. Errors might cause a permanent
brick!
Enabling management access from LAN:
Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:
- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"
Notes on the OEM/bootloader dual partition scheme
The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.
Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.
The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.
If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.
If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.
If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally. CheckBypass is set to 1 after each successful
validation of Image1.
Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger. But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.
The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.
Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.
Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-04-19 11:00:56 +00:00
|
|
|
define Device/zyxel_nr7101
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: mt7621: Add support for ZyXEL NR7101
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E
- Switch: 1 LAN port (Gigabiti)
- 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
- SIM: 2 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/yellow under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable. Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.
A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.
MAC addresses:
OpenWrt OEM Address Found as
lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label
wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex)
wwan0 usb0 random
WARNING!!
ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled. Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.
Installation from OEM web GUI:
- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Installation from OEM ssh:
- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
nvram setro uboot DebugFlag 0x1
nvram setro uboot CheckBypass 0
nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Copying OpenWrt to the recovery partition:
- Verify that you are running a working OpenWrt recovery image
from flash
- ssh to root@192.168.1.1 and run:
fw_setenv CheckBypass 0
mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2
NOTE: This should only be done after successfully booting the OpenWrt
recovery image from the primary partition during installation. Do
not do this after having sysupgraded OpenWrt! Reinstalling the
recovery image on normal upgrades is not required or recommended.
Installation from Z-Loader:
- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image
NOTE: ATNR will write the recovery image to both primary and recovery
partitions in one go.
Booting from RAM:
- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
header
This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies! Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.
NOTE: U-Boot configuration is incomplete (on some devices?). You may
have to configure a working mac address before running tftp using
"setenv eth0addr <mac>"
Unlocking the bootloader:
If you are unebale to halt boot, then the bootloader is locked.
The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0. Setting it to 1 is therefore only temporary
when OEM firmware is installed.
- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt
NOTE:
OpenWrt does this automatically on first boot if necessary
NOTE2:
Setting the flag to 0x1 avoids the reset to 0 in known OEM
versions, but this might change.
WARNING:
Writing anything to flash while the bootloader is locked is
considered extremely risky. Errors might cause a permanent
brick!
Enabling management access from LAN:
Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:
- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"
Notes on the OEM/bootloader dual partition scheme
The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.
Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.
The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.
If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.
If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.
If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally. CheckBypass is set to 1 after each successful
validation of Image1.
Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger. But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.
The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.
Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.
Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-04-19 11:00:56 +00:00
|
|
|
DEVICE_VENDOR := ZyXEL
|
|
|
|
|
DEVICE_MODEL := NR7101
|
2023-05-13 13:01:00 +00:00
|
|
|
KERNEL_SIZE := 31488k
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
ramips: mt7621: Add support for ZyXEL NR7101
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E
- Switch: 1 LAN port (Gigabiti)
- 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
- SIM: 2 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/yellow under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable. Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.
A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.
MAC addresses:
OpenWrt OEM Address Found as
lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label
wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex)
wwan0 usb0 random
WARNING!!
ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled. Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.
Installation from OEM web GUI:
- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Installation from OEM ssh:
- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
nvram setro uboot DebugFlag 0x1
nvram setro uboot CheckBypass 0
nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Copying OpenWrt to the recovery partition:
- Verify that you are running a working OpenWrt recovery image
from flash
- ssh to root@192.168.1.1 and run:
fw_setenv CheckBypass 0
mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2
NOTE: This should only be done after successfully booting the OpenWrt
recovery image from the primary partition during installation. Do
not do this after having sysupgraded OpenWrt! Reinstalling the
recovery image on normal upgrades is not required or recommended.
Installation from Z-Loader:
- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image
NOTE: ATNR will write the recovery image to both primary and recovery
partitions in one go.
Booting from RAM:
- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
header
This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies! Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.
NOTE: U-Boot configuration is incomplete (on some devices?). You may
have to configure a working mac address before running tftp using
"setenv eth0addr <mac>"
Unlocking the bootloader:
If you are unebale to halt boot, then the bootloader is locked.
The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0. Setting it to 1 is therefore only temporary
when OEM firmware is installed.
- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt
NOTE:
OpenWrt does this automatically on first boot if necessary
NOTE2:
Setting the flag to 0x1 avoids the reset to 0 in known OEM
versions, but this might change.
WARNING:
Writing anything to flash while the bootloader is locked is
considered extremely risky. Errors might cause a permanent
brick!
Enabling management access from LAN:
Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:
- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"
Notes on the OEM/bootloader dual partition scheme
The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.
Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.
The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.
If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.
If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.
If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally. CheckBypass is set to 1 after each successful
validation of Image1.
Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger. But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.
The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.
Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.
Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-04-19 11:00:56 +00:00
|
|
|
KERNEL := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
|
|
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | zytrx-header $$(DEVICE_MODEL) 9.99(ABUV.9)$$(VERSION_DIST)-recovery
|
|
|
|
|
KERNEL_INITRAMFS_SUFFIX := -recovery.bin
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_nr7101
|
|
|
|
|
|
2022-05-27 15:48:06 +00:00
|
|
|
define Device/zyxel_nwa-ax
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-05-27 15:48:06 +00:00
|
|
|
DEVICE_VENDOR := ZyXEL
|
|
|
|
|
KERNEL_SIZE := 8192k
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware zyxel-bootconfig
|
2022-05-27 15:48:06 +00:00
|
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
|
|
|
|
IMAGES += factory.bin ramboot-factory.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | zyxel-nwa-fit
|
|
|
|
|
IMAGE/ramboot-factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/zyxel_nwa50ax
|
|
|
|
|
$(Device/zyxel_nwa-ax)
|
|
|
|
|
DEVICE_MODEL := NWA50AX
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_nwa50ax
|
|
|
|
|
|
|
|
|
|
define Device/zyxel_nwa55axe
|
|
|
|
|
$(Device/zyxel_nwa-ax)
|
|
|
|
|
DEVICE_MODEL := NWA55AXE
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_nwa55axe
|
|
|
|
|
|
ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)
Hardware
--------
SoC: MediaTek MT7621ST
WiFi: MediaTek MT7603
Quantenna QT3840BC
Flash: 128M NAND
RAM: 64M
LED: Dual colour red and green
BTN: Reset
WPS
Eth: 4 x 10/100/1000 connected to MT7621 internal switch
MT7621 RGMII port connected to Quantenna module
GPIO: Power/reset of Quantenna module
Quantenna module
----------------
The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation. It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621. It loads both a second uboot stage and an os
image from the MT7621 using tftp. The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.
There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.
Serial ports
------------
Two serial ports with headers:
RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1 - 57600 8N1 - Connected to the MT7621 console
Both share pinout with many other Zyxel/Mitrastar devices:
1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND
Dual system partitions
----------------------
The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.
OpenWrt does not support this scheme and will always use the
first OS partition. It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.
Installation from vendor firmware
---------------------------------
1. Run a DHCP server. The WAP6805 is configured as a client device
and does not have a default static IP address. Make a note of
which address it is assigned
2. tftp the OpenWrt initramfs-kernel.bin image to this address.
Wait for the WAP6805 to reboot.
3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
backup of all mtd partitions now. The last used OEM image is
still present in either "Kernel" or "Kernel2" at this point,
and can be restored later if you save a copy.
4. sysupgrade to the OpenWrt sysupgrade.bin image.
Installation from U-Boot
------------------------
This requires serial console access
1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
your tftp server directory. Configure the server address as
192.168.0.33/24
2. Hit ESC when the message "Hit ESC key to stop autoboot"
appears
3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.
4. Answer Y to the question "Erase Linux in Flash then burn new
one. Are you sure?", and answer the address/filename questions.
Defaults:
Input device IP (192.168.0.2)
Input server IP (192.168.0.33)
Input Linux Kernel filename ("ras.bin")
5. Wait until after you see the message "Done!" and power cycle
the device. It will hang after flashing.
6. Continue with step 3 and 4 from the vendor firmware procedure.
Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme. These changes appear to have
broken a few things. The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work. The image selection
scheme is unreliable and inconsistent. A limited U-Boot menu is
available - and used by the above U-Boot install procedure. But
direct booting into an uploaded image does not work, neither with
ram nor with flash. Flashing works, but requires a hard reset after
it is finished.
Reverting to OEM firmware
-------------------------
The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.
ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin
OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required. See above.
Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware. But the branding features do obviously
differ.
LED controller
--------------
Hardware implementation is unknown. The dual-color LED is controlled
by 3 GPIOs:
4: red
7: blinking green
13: green
Enabling both red and green makes the LED appear yellow.
The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-04-18 19:57:52 +00:00
|
|
|
define Device/zyxel_wap6805
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
2022-11-28 14:45:12 +00:00
|
|
|
$(Device/uimage-lzma-loader)
|
ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)
Hardware
--------
SoC: MediaTek MT7621ST
WiFi: MediaTek MT7603
Quantenna QT3840BC
Flash: 128M NAND
RAM: 64M
LED: Dual colour red and green
BTN: Reset
WPS
Eth: 4 x 10/100/1000 connected to MT7621 internal switch
MT7621 RGMII port connected to Quantenna module
GPIO: Power/reset of Quantenna module
Quantenna module
----------------
The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation. It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621. It loads both a second uboot stage and an os
image from the MT7621 using tftp. The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.
There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.
Serial ports
------------
Two serial ports with headers:
RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1 - 57600 8N1 - Connected to the MT7621 console
Both share pinout with many other Zyxel/Mitrastar devices:
1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND
Dual system partitions
----------------------
The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.
OpenWrt does not support this scheme and will always use the
first OS partition. It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.
Installation from vendor firmware
---------------------------------
1. Run a DHCP server. The WAP6805 is configured as a client device
and does not have a default static IP address. Make a note of
which address it is assigned
2. tftp the OpenWrt initramfs-kernel.bin image to this address.
Wait for the WAP6805 to reboot.
3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
backup of all mtd partitions now. The last used OEM image is
still present in either "Kernel" or "Kernel2" at this point,
and can be restored later if you save a copy.
4. sysupgrade to the OpenWrt sysupgrade.bin image.
Installation from U-Boot
------------------------
This requires serial console access
1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
your tftp server directory. Configure the server address as
192.168.0.33/24
2. Hit ESC when the message "Hit ESC key to stop autoboot"
appears
3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.
4. Answer Y to the question "Erase Linux in Flash then burn new
one. Are you sure?", and answer the address/filename questions.
Defaults:
Input device IP (192.168.0.2)
Input server IP (192.168.0.33)
Input Linux Kernel filename ("ras.bin")
5. Wait until after you see the message "Done!" and power cycle
the device. It will hang after flashing.
6. Continue with step 3 and 4 from the vendor firmware procedure.
Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme. These changes appear to have
broken a few things. The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work. The image selection
scheme is unreliable and inconsistent. A limited U-Boot menu is
available - and used by the above U-Boot install procedure. But
direct booting into an uploaded image does not work, neither with
ram nor with flash. Flashing works, but requires a hard reset after
it is finished.
Reverting to OEM firmware
-------------------------
The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.
ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin
OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required. See above.
Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware. But the branding features do obviously
differ.
LED controller
--------------
Hardware implementation is unknown. The dual-color LED is controlled
by 3 GPIOs:
4: red
7: blinking green
13: green
Enabling both red and green makes the LED appear yellow.
The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-04-18 19:57:52 +00:00
|
|
|
IMAGE_SIZE := 32448k
|
|
|
|
|
DEVICE_VENDOR := ZyXEL
|
|
|
|
|
DEVICE_MODEL := WAP6805
|
2023-02-28 11:39:36 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7621-qtn-rgmii -uboot-envtools
|
2022-11-28 14:45:12 +00:00
|
|
|
KERNEL := $$(KERNEL/lzma-loader) | uImage none | uimage-padhdr 160
|
ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)
Hardware
--------
SoC: MediaTek MT7621ST
WiFi: MediaTek MT7603
Quantenna QT3840BC
Flash: 128M NAND
RAM: 64M
LED: Dual colour red and green
BTN: Reset
WPS
Eth: 4 x 10/100/1000 connected to MT7621 internal switch
MT7621 RGMII port connected to Quantenna module
GPIO: Power/reset of Quantenna module
Quantenna module
----------------
The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation. It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621. It loads both a second uboot stage and an os
image from the MT7621 using tftp. The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.
There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.
Serial ports
------------
Two serial ports with headers:
RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1 - 57600 8N1 - Connected to the MT7621 console
Both share pinout with many other Zyxel/Mitrastar devices:
1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND
Dual system partitions
----------------------
The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.
OpenWrt does not support this scheme and will always use the
first OS partition. It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.
Installation from vendor firmware
---------------------------------
1. Run a DHCP server. The WAP6805 is configured as a client device
and does not have a default static IP address. Make a note of
which address it is assigned
2. tftp the OpenWrt initramfs-kernel.bin image to this address.
Wait for the WAP6805 to reboot.
3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
backup of all mtd partitions now. The last used OEM image is
still present in either "Kernel" or "Kernel2" at this point,
and can be restored later if you save a copy.
4. sysupgrade to the OpenWrt sysupgrade.bin image.
Installation from U-Boot
------------------------
This requires serial console access
1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
your tftp server directory. Configure the server address as
192.168.0.33/24
2. Hit ESC when the message "Hit ESC key to stop autoboot"
appears
3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.
4. Answer Y to the question "Erase Linux in Flash then burn new
one. Are you sure?", and answer the address/filename questions.
Defaults:
Input device IP (192.168.0.2)
Input server IP (192.168.0.33)
Input Linux Kernel filename ("ras.bin")
5. Wait until after you see the message "Done!" and power cycle
the device. It will hang after flashing.
6. Continue with step 3 and 4 from the vendor firmware procedure.
Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme. These changes appear to have
broken a few things. The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work. The image selection
scheme is unreliable and inconsistent. A limited U-Boot menu is
available - and used by the above U-Boot install procedure. But
direct booting into an uploaded image does not work, neither with
ram nor with flash. Flashing works, but requires a hard reset after
it is finished.
Reverting to OEM firmware
-------------------------
The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.
ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin
OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required. See above.
Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware. But the branding features do obviously
differ.
LED controller
--------------
Hardware implementation is unknown. The dual-color LED is controlled
by 3 GPIOs:
4: red
7: blinking green
13: green
Enabling both red and green makes the LED appear yellow.
The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-04-18 19:57:52 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_wap6805
|
ramips: mt7621: add support for ZyXEL WSM20
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.
Specifications
==============
SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)
MAC address assignment
======================
The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.
The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.
Installation (web interface)
============================
The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.
The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.
1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy
NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.
Installation (UART method)
==========================
The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:
1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation
Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:
nand read 1800000 53c0000 800
mw.b 1800004 1 1
nand erase 53c0000 800
nand write 1800000 53c0000 800
This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.
Back to stock
=============
It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.
It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:
mtd write zyxel.bin Kernel2
echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
2023-04-04 17:41:26 +00:00
|
|
|
|
|
|
|
|
define Device/zyxel_wsm20
|
2023-05-13 13:01:00 +00:00
|
|
|
$(Device/nand)
|
ramips: mt7621: add support for ZyXEL WSM20
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.
Specifications
==============
SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)
MAC address assignment
======================
The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.
The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.
Installation (web interface)
============================
The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.
The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.
1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy
NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.
Installation (UART method)
==========================
The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:
1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation
Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:
nand read 1800000 53c0000 800
mw.b 1800004 1 1
nand erase 53c0000 800
nand write 1800000 53c0000 800
This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.
Back to stock
=============
It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.
It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:
mtd write zyxel.bin Kernel2
echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
2023-04-04 17:41:26 +00:00
|
|
|
KERNEL_SIZE := 8192k
|
|
|
|
|
IMAGE_SIZE := 41943040
|
|
|
|
|
DEVICE_VENDOR := ZyXEL
|
|
|
|
|
DEVICE_MODEL := WSM20
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt7915-firmware
|
|
|
|
|
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | znet-header V1.00(ABZF.0)C0
|
|
|
|
|
KERNEL_INITRAMFS := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | znet-header V1.00(ABZF.0)C0
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_wsm20
|
