Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16057
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Unused wan mac added to dts. Requires DSA to implement.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get vlan 4k for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get mc index for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get ports speed for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Detect the RTL8367D chip family and set the appropriate extif
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disables Data Center Bridging support for some network drivers by
default to avoid compilation errors when CONFIG_DCB is enabled.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3B is a Pico-ITX form factor SBC[1] using the Rockchip
RK3568(J).
Hardware
--------
- Rockchip RK3568(J) SoC
- Quad A55 CPU
- Mali-G52 GPU
- 1 TOPS @ INT8 NPU
- 2GB/4GB/8GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key (2-lane PCIe 3.0)
- SPI Flash for bootloader
- 2x Gigabit ethernet port (one supports PoE with add-on PoE HAT)
- 1x M.2 E Key socket with SDIO, UART and USB interfaces
- 1x M.2 B Key socket with PCIe, SATA, and USB interfaces
- 1x SIM card socket
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST ports
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3b
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3C is a high-performance, low-cost SBC[1] using the
Rockchip RK3566.
Hardware
--------
- Rockchip RK3566 SoC
- Quad A55 CPU
- Mali-G52-2EE GPU
- 1 TOPS @ INT8 NPU
- 1GB/2GB/4GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key connector(2230) or M.2 Extension
board(2232/2260/2280)
- SATA through the Radxa Penta SATA HAT
- 1x Gigabit ethernet port(supports PoE with add-on PoE HAT)
- WiFi6/BT5.4 (not supported yet on OpenWrt)
- 1x USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- 1x USB 2.0 Type-A OTG port
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3c
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All boards using the deprecated uImage.FIT partition parser have
been migrated to the new fitblk driver. Drop the now no longer
needed partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
That patch title of 911-kobject_add_broadcast_uevent.patch has been
wrongly copied from 910-kobject_uevent.patch.
Change the description from "lib: add uevent_next_seqnum()" to
"lib: add broadcast_uevent()", so that the git history doesn't look
all weird when importing both patches to a git tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes model name in dts as below:
Radxa ROCK3 model A -> Radxa ROCK 3A
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16232
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Like x86, armsr is frequently virtualized, and is used for development
and debugging. Kernel messages should be more readily apparent by
default. This can be achieved by adding console=tty1 to the kernel
command line, enabling the console on a (possibly virtual) display and
keyboard, in addition to a serial port.
This also enables failsafe on tty1. Failsafe mode operates on consoles
known by the kernel, without regard to /etc/inittab.
armsr's /etc/inittab is also updated to specify tty1 instead of tty0.
tty1 is technically more correct: tty1 is the first virtual console,
where tty0 reflects the current active virtual console (which is likely
to be tty1).
This configuration matches x86, which is another target commonly used
for virtualization, development, and debugging in the same way. x86's
kernel command line had specified console=tty0, although console=tty1 is
more correct for the reasons given above. This also brings x86's kernel
command line console= into agreement with its /etc/inittab, which
already used tty1.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16213
Signed-off-by: Robert Marko <robimarko@gmail.com>
Found with coccinelle:
No need to set .owner here. The core will do it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16217
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link TD-W8968 v3 is an 300Mbps Wireless N USB ADSL2+ Modem Router based on
Broadcom BCM6318 SoC.
Hardware:
CPU: Broadcom BCM6318, 333 MHz, 1 core
Flash: 8MB
RAM: 64 MB
Ethernet: 4x 10/100 Mbps
Wireless: 802.11b/g/n, BCM43217
LEDs/Buttons: 10x / 3x
USB: 1x 2.0
Flash instructions:
* Assign static IP 192.168.1.100 to PC
* Unplug the power source
* Press the RESET button at the router, don't release it yet!
* Plug the power source. Wait for some seconds
* Release the RESET button
* Browse to http://192.168.1.1
* Upload the openwrt-bmips-bcm6318-tp-link_td-w8968-v3-squashfs-cfe.bin file
* Wait some minutes until the firmware upgrade finish.
Signed-off-by: Mathesh Velayudan <123v.mathesh@gmail.com>
Device support for Sophos AP15 is based on Sophos AP55(C) and AP100(C).
Those other Sophos access points uss a QCA9558 SoC (some of them with
one of the three chains on the built-in SoC's wifi disabled) while the
AP15 uses a QCA9557 SoC (which only has two chains enabled in the
package or silicon).
This is mostly cosmetic since QCA9558 and QCA9557 are virtually
identical and all differences are automatically detected and/or managed
by the ART calibration.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/16187
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16230
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit introduces led nodes in tl-wdr4900-v1 dts.
It allows to configure switch leds from userspace.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link tl-wdr4900-v1 has two usb leds. Modern kernels can handle usb
led trigger. Let's enable it.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit change led description in dts file from old method to new
approach accepted by upstream.
USB power gpio is handled by gpio-export now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
Ever since CONFIG_ARM64_PAN was enabled Common Not Private (CNP) is now
visible and kernel builds will stop as they are not set in kernel config
for 5.15 and 6.1.
So, lets enable Common Not Private (CNP) which is ARMv8.2 feature and will
be NOP of CPU-s that dont support it.
Fixes: a2662309aa ("kernel: Enable CONFIG_ARM64_PAN to restrict kernel access to user space memory")
Link: https://github.com/openwrt/openwrt/pull/16211
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enhanced Privileged Access Never (EPAN) is an ARMv8.7 feature, and since
we dont have any SoC-s implementing it lets disable it.
Link: https://github.com/openwrt/openwrt/pull/16211
Signed-off-by: Robert Marko <robimarko@gmail.com>
The commit backporting new MTK patches did not update the
Kernel config for mediatek/mt7622 causing the build to
fail.
Simply use the new config symbol name for the driver to
fix the issue.
Fixes: 1069514978 ("mediatek: backport pending Ethernet PHY driver patches")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/16225
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use pending patchset for 2.5GE PHY driver, unifying LED handling
accross all MediaTek Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kconfig symbols CONFIG_ARM64_CNP and CONFIG_ARM64_EPAN got exposed
by enabling CONFIG_ARM64_PAN. Enable them as well, as just like for
PAN, also EPAN and CNP will be detected at runtime at no cost.
Fixes: a2662309aa ("kernel: Enable CONFIG_ARM64_PAN to restrict kernel access to user space memory")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
No benefit in doing so in platform file. Code for dts has already been
written. Might as well use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated. No need for any of this.
Calibration size was adjusted to 440, which is the standard value for
ath9k radios.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that the ports are defined in DTS, this is trivial to do.
Avoids userspace handling.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
The kernel support necessary to use a console keyboard was not built on
x86, affecting real and virtual machines alike. The console keyboard
would function properly in GRUB, but would not work at all once Linux
booted. It appeared that the console was intended to work because
console video appeared on the display, including prompts to enter
failsafe or select the debug log level from the keyboard, and the prompt
to "Press Enter to activate this console", but there was no way to
provide input to it. All keystrokes were ignored.
This enables several kernel configuration options to enable HID and USB
HID support (CONFIG_HID, CONFIG_HID_SUPPORT, CONFIG_HID_GENERIC, and
CONFIG_USB_HID), making the keyboard functional. For alignment with
armsr, CONFIG_USB_HIDDEV is also added, although not strictly necessary
for keyboard support. Note that this change also causes
CONFIG_HID_HYPERV_MOUSE to be enabled for x86/64 and x86/generic: it was
already set in these subarchitectures' kernel configurations, but was
ineffective due to CONFIG_HID being absent.
The omission of keyboard support on x86 may not have been widely noticed
because USB HID is not used on production OpenWrt x86 machines such as
pc-engines,apu2 which only have a serial console, or with the default
x86 configuration used by scripts/qemustart, which uses -nographic and
does not configure a virtual physical console but instead uses a serial
console.
This configuration change results in, for x86_64, +40kB in kernel.bin
and just over +40kB in gzip-compressed "combined" images. This should
not be a problem for the non-storage-constrained x86 target.
Until 2a86425de1, CONFIG_HID, CONFIG_USB_HID, and CONFIG_USB_HIDDEV
were set in the target-level kernel configuration, and
CONFIG_HID_GENERIC was set at the subtarget level. These are
reintroduced strictly at the subtarget level by request. This applies to
the 64, generic, and legacy subtargets, omitting geode.
Fixes: https://github.com/openwrt/openwrt/issues/16157
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16208
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable the CONFIG_ARM64_PAN kernel security option, which leverages the
ARMv8.1 Privileged Access Never (PAN) extension to prevent the kernel
from directly accessing user space memory.
Instead, copy_to_user and similar functions must be used for data
transfer between kernel and user space. This feature is automatically
disabled at runtime on CPUs without PAN support, making it a no-op in
those cases.
Link: https://github.com/openwrt/openwrt/pull/16189
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Activate the kernel option CONFIG_LIST_HARDENED for all targets.
This adds some inline checks to list_add() and list_del() operations
in the kernel. Before kernel 6.6 these checks were only available with
CONFIG_DEBUG_LIST option, but now a light version is available which
should only add very few extra instructions to such operations.
The performance penalty is very low from my point of view. It should
make it much harder to use bugs in Linux kernel list handling when
exploiting the Linux kernel.
Link: https://github.com/openwrt/openwrt/pull/16189
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
2500 Base-T
RGB LED
eMMC Connector
SPI-NOR 16MB
Micro-SD Slot
2x USB 2.0 Port
2x USB 3.0 Port
Headphone Jack
M.2 E-Key
M.2 M-Key
USB PD 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
1000 Base-T
Status LED
eMMC/SPI Connector
Micro-SD Slot
2x USB 3.0 Port
2x USB 2.0 Port
Headphone Jack
M.2 E-Key
USB PD/QC 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now we have rk3588 support :)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit f98f95359b.
It seems that this commit is causing issues with the PWM fan on the RPi 5 as
reported here: https://github.com/openwrt/openwrt/issues/16191
So let's revert this for now.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The D-Link DSL-2750B rev B1 (AW4339U) is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.
This ports the device from old target bcm63xx/generic to bmips/bcm6328.
The hardware is the same of D-Link DSL-2740B rev F1 and DSL-2741B rev F1, plus a usb2 port.
Hardware:
- SoC: Broadcom BCM63281
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB (Nanya NT5TU32M16DG)
- Flash: 8 MB NOR (Macronix MX25L6406ENI-12G)
- Ethernet LAN: 4x 100Mbit (Broadcom BCM63281)
- Wifi 2.4 GHz: 802.11bgn (Atheros AR9287)
- USB: 1x 2.0
- Buttons: 3x
- LEDs: 10x
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Samuele Longhi <agave@dracaena.it>
It's upstream and a replacement for the swconfig driver.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16124
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allows removing free_irq. Simpler.
Oddly enough the other switch code already does this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16050
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware:
- SoC: MediaTek MT7628DAN (MIPS 580MHz)
- Flash: 8 MiB Spansion S25FL064K
- RAM: 64 MiB (built-into SoC)
- WLAN: 2.4 GHz (MT7628)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- Buttons: 1 Reset button
- LEDs: 1x Red, 1x Green
- Serial console: unpopulated header, 57600 8n1 (RX only)
- Power: 12 VDC, 1 A
There are unpopulated areas on the board for 5 GHz WiFi via PCIe as well
as (most likely) Quectel EG25-G 4G module. As both are not populated on
my board support for both is missing for now.
Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.188.253/ and upload sysupgrade.bin file.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the KERNEL_BTRFS_FS config option so that targets can select
whether BTRFS support must be built-in.
Select this option (alongside KERNEL_BTRFS_FS_POSIX_ACL) from the
layerscape/armv8_64b subtarget instead of enabling it in
target/linux/layerscape/armv8_64b/config-* files.
Move disabling of CONFIG_BTRFS_FS_CHECK_INTEGRITY into generic configs.
This makes it possible for OpenWRT to be built with built-in BTRFS
support on specific boards, instead of whole targets.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/15990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
- MT7629 CPU
- MT7531 switch
- MT7761N and MT7762N wifi
- 256 MB RAM
- 128 MB NAND flash with dual-boot partitions
- 2 buttons: WPS and reset
- 1 WAN port (1G)
- 4 LAN ports (1G)
- 1 USB port
Limitations (same as other MT7629/MT7761N/MT7762N devices):
- Wifi is not working
- Second core is not working (kernel error message "CPU1: failed to come online")
Disassembly:
- There are two screws under the front rubber feet and two under the label on the bottom (in the corners towards the back, you should be able to feel them).
Serial Interface:
- UART pin header is already soldered on the board. Pinning from front to back:
1 - VCC
2 - TX
3 - RX
4 - n/a
5 - GND
GPIO:
- 1 white LED, connected to GPIO 52
- 1 reset button, connected to GPIO 60
- 1 WPS button, connected to GPIO 58
MAC Adresses:
- The MAC address printed on the device label is used for LAN and WAN
- The MAC address is stored in the devinfo partition in ASCII format (hw_mac_addr=aa:bb:cc:dd:ee)
- 2.4 GHz wifi uses MAC of the device label + 1
- 5 GHz wifi uses MAC of the device label + 2
Flashing:
- OpenWrt is only runnig in the first partition of dual boot
- To ensure to be able to go back to the factory image, flash the last OEM firmware via OEM web interface. This will ensure that the OEM firmware is present on both partitions
- Because of dual boot partitions, flashing via OEM interface is not supported
- Start a TFTP server and provide the initramfs image. Default settings:
- Router IP: 192.168.1.1
- TFTP server IP: 192.168.1.100
- TFTP file name: 7531.bin
- Open the device, connect UART and select " 1. System Load Linux to SDRAM via TFTP." during startup
- Adapt the settings to your environment, if required
- After initramfs is booted, flash the sysupgrade image
Return to OEM firmware:
- Run the following commands in OpenWrt to switch to the second partition
fw_setenv boot_part 2
fw_setenv bootimage 2
- Reboot the device. OEM firmware will start up again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16067
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SUPPORTED_DEVICES is required for Radxa ROCK Pi S.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the LED definitons for the XG6846 DSA port LEDs.
These are standard properties compatible with the existing
Marvell 88e6xxx DT bindings and fully standardized so this
is fine to add. They will be used by the in-flight Marvell
88e6xxx LEDs support patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[add empty lines between leds, remove default-state="off"]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
For some troublesome devices it is necessary to obtain direct access
to the SFP module EEPROM so define it in the device tree.
Suggested-by: Paul Donald <newtwen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some versions of the Inteno XG6846 has a USB port mounted.
For these machines the corresponing USB port nodes need to
be enabled.
Suggested-by: Henrik Ginstmark <henrik@ginstmark.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[reorder DTS alphabetically]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
997acc7f86 split this PHY driver up such
that external QCA switches now use CONFIG_QCA83XX_PHY. Fix it here so
that ethernet works again.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16154
Signed-off-by: Robert Marko <robimarko@gmail.com>
The second edition of international version of Mi Router 4A 100M is
very similar to the non-international one, but has another wireless chip.
Installation
--------------
1. Initialize build-in firmware (use webgui for 192.168.31.1)
You should install root password
2. Run OpenWRTInvasion for the first time (probably it will fail)
Version 0.0.10 is working as well as 0.0.1.
3. Run OpenWRTInvasion for the second time
It will create an access to your router
4. Upload sysupgrade image to router (/tmp/fw.bin)
pc# nc -l 8080 < …/ramips/mt76x8/…-100m-intl-v2-squashfs-sysupgrade.bin
router# nc 192.168.31.175 8080 > /tmp/fw.bin
5. Flash new firmware
router# run mtd -r write /tmp/fw.bin OS1
6. Check result
Wait about 5-10 minutes after flash. Router should reboot itself and
turn left led from orange to blue.
In case of failure one can use Xiaomi 4a 100m debrick tool
(it uploads special image via tftpd in recovery mode)
After that you can start again from step 1.
Another actions are very similar to original Mi Router 4A 100M
Original mtd paritions:
-------------------------
```
Creating 9 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000020000 : "Bootloader"
0x000000020000-0x000000030000 : "Config"
0x000000030000-0x000000040000 : "Factory"
0x000000040000-0x000000050000 : "crash"
0x000000050000-0x000000060000 : "cfg_bak"
0x000000060000-0x000000160000 : "overlay"
0x000000160000-0x000000dc0000 : "OS1"
0x000000dc0000-0x000001000000 : "disk"
with special sub-partition
0x0000002c0000-0x000000dc0000 : "rootfs"
```
We will use OS1+disk space:
```
0x000000160000-0x000001000000 : "firmware"
```
Co-authored-by: Nita Vesa <nita.vesa@elektrik.link>
Signed-off-by: Anton Stratonnikov <billic@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/14304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NVMEM is the upstream replacement for this. ralink,mtd-eeprom is
deprecated. The others need to stay as there's byte swapping going on.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16084
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also migrate mt7623 to new fitblk support scripts which simplify
sysupgrade when using uImage.FIT. This had been forgotten previously.
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Simplifies the code by removing clk_disable_unprepare.
Also removed gotos and used dev_err_probe.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16133
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a use-after-free bug in mtk_wed_setup_tc_block_cb()
which leads to kernel panic when setup multiple ap
interfaces on one band of mt798x.
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16118
Signed-off-by: Robert Marko <robimarko@gmail.com>
Read the 'fip' static volume in order to trigger scrubbing in case of
detecting flipped bits while reading.
We have to do this in Linux because we never read or touch the 'fip'
volume and the UBISPL implementation in ARM TrustedFirmware-A does NOT
handle scrubbing itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reporting an unclean read from SPI-NAND only when the maximum number
of correctable bitflip errors has been hit seems a bit late.
UBI LEB scrubbing, which depends on the lower MTD device reporting
correctable bitflips, then only kicks in when it's almost too late.
Set bitflip_threshold to 75% of the ECC strength, which is also the
default for raw NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It seems that some Xiaomi AX3000T boards changed to using Winbond W25N01KV
SPI-NAND which is not supported in OpenWrt nor upstream kernel.
So, add a pending patch to support it as upstream supports rest of the KV
revision models.
Fixes: #16002
Link: https://github.com/openwrt/openwrt/pull/16088
Signed-off-by: Robert Marko <robimarko@gmail.com>
We need to configure the led and network config for this board on
start as per the others
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches for the nanopi r6s board, backporting from 6.9 where
basic support is landing.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.
Hardware:
Model: Cambium Networks XE3-4
CPU: IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
Memory: 1 GiB
Flash: 512 MiB Macronix MX30UF2G18AC + W25Q128FW
Ethernet: 1x 1 GbE (QCA8072)
1x 2.5 GbE (QCA8081)
Buttons: 1x Reset
Serial: TX, RX, GND
Baudrate: 115200
Radios: Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
BLE 4.1
Power: 32.0W 802.3bt5 PoE++
25.5W 802.3at with USB, BT disabled
Size: 215mm x 215mm
Ports: 1x USB 2.0
Antenna: 6 GHz: 6.29 dBi, Omni 30 dBm
5 GHz: 6.12 dBi, Omni 31 dBm
2.4 GHz: 4.85 dBi, Omni 29 dBm
LEDs: Multi-color status LEDs
Mounting: Wall, ceiling or T-bar
Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
one of the APs GND pins.
3. Transfer the initramfs image with TFTP
(Default server IP is 192.168.0.120)
# tftpboot factory.ubi
4. Flash the rootfs partition
# flash rootfs
5. Reboot the AP
# reset
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15633
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes the image check failed on system upgrade
"Image check failed:
upgrade: Device radxa,rock3a not supported by this image
upgrade: Supported devices: radxa,rock-3a"
Signed-off-by: Tomas Lara <tl849670@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to RTL8221B's datasheet, the PHY requires at least 10ms
for assert and 68ms (recommended) for de-assert. So increase the
assert/de-assert time to 15ms and 68ms respectively.
Fixes: c0c3234e17 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16106
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refactor Inteno XG6846 device tree to be in line with other bmips devices.
Also expose USB LED automatically.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Enable CONFIG_HWMON and CONFIG_THERMAL_HWMON on all subtargets.
- Drop kmod-thermal from bcm2712.
- Add CONFIG_SENSORS_RASPBERRYPI_HWMON generic symbol.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
target/linux/archs38/image/Makefile calls gen_axs10x_sdcard_img.sh
with $(CONFIG_TARGET_ROOTFS_PARTSIZE).
Make sure a rootfs partition is built and usable.
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Link: https://github.com/openwrt/openwrt/pull/16098
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ec885796c0 switched the crc32 implementation from default to
byte-at-a-time algorithm, which runs slower but consumes less memory.
A decade has passed, and we have already abandoned targets that had
small memory, so switch it back to default for faster speed.
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Enable the CONFIG_MTD_SPI_NOR_USE_VARIABLE_ERASE kernel option to allow for
U-Boot environment writing. This might be hiding a problem somewhere else,
since the w25q128fw chip supports 32K erases, still this change makes it
much easier to switch the GL-MV1000 boot media without an UART cable
connection.
Thanks to @robimarko and @hacks for the precious hints and suggesting a
better approach.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
This allows booting from internal eMMC or SD card just changing the
U-Boot mmc_dev variable.
In particular, setting mmc_dev to 1 will result in booting from the SD card.
Setting the variable to 0 will result in internal eMMC boot (the default).
Should the variable be unset or an error condition occur while reading
from SD card, internal MMC booting will be tried.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
mpc85xx was switched to 6.6. We can remove 6.1 support now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16087
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's time for wide tests.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16087
Signed-off-by: Robert Marko <robimarko@gmail.com>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.44..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds auto-configuration of network ports on Dell EMC Edge620 (x86) product.
It is similar in specs/features to some of the Sophos x86-based appliances, but:
1. Serial console terminal is built in and requires just the micro-USB cable
2. Comes with both MMC (16Gb) and SSD (256Gb) installed
3. Comes with 6 ethernet ports all 6 are functional when no SFP is used
4. Comes with two SFP cages and not one, like some of revision 3 Sophos products
5. Unlike Sophos devices, there are no non-wireless models of Edge 620,
it comes with Qualcomm Atheros QCA9880 radio
These devices can be now found both second-hand and new at online marketplaces below
(sometimes well below) US $100, I believe they make great candidates for running OpenWrt.
The ethernet network ports on the case are marked GE1 thru to GE6 with the
following mapping once booted into OpenWrt:
```
GE1: eth2: pci0000:00/0000:00:0b.0/0000:02:00.2
GE2: eth3: pci0000:00/0000:00:0b.0/0000:02:00.3
GE3: eth0: pci0000:00/0000:00:0b.0/0000:02:00.0
GE4: eth1: pci0000:00/0000:00:0b.0/0000:02:00.1
GE5: eth7: pci0000:00/0000:00:17.0/0000:07:00.1
GE6: eth6: pci0000:00/0000:00:17.0/0000:07:00.0
```
Dell's instructions for [standard configuration](https://infohub.delltechnologies.com/en-us/l/dell-emc-edge-620-advanced-activation-guide/dell-emc-sd-wan-edge-620-standard-configuration/)
recommend using GE3, GE4, GE5, or GE6 for WAN, I've selected the GE6 as the sole
WAN port under OpenWrt with the rest of ethernet ports assigned to LAN.
Please merge before 24.xx is forked and if possible, cherry-pick for 23.05
if there's no ETA for 24.xx forking.
PS. @Hurricos I'm struggling with ixgbe mappings on Sophos devices which use
very similar hardware to Dell EMC, so even tho I know the sys paths for ethernet ports,
I'd prefer to do a separate commit to properly map ethernet ports to match the case markings
for this device at some point later.
Signed-off-by: Stan Grishin <stangri@melmac.ca>
Use realtek,extif property instead of realtek,extif0 to extif2
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Store the chip type in smi->rtl8367b_chip
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove the rlvid analysis because for the rtl8367b family chips supported
by the driver (rtl8367rb and rtl8367r-vb), rlvid is always equal to 1.
So the code for rlvid equal to 0 is completely unnecessary.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use realtek,extif property instead of realtek,extif0 and realtek,extif1
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop config for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16030
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16030
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new utility, omnia-mcutool, which main purpose is to upgrade the
firmware on the microcontroller on the Turris Omnia router. Depends on
omnia-mcu-firmware, and the upgrade process is pretty simple:
omnia-mcutool --upgrade
Besides firmware upgrade, the utility can be used to show and configure
various firmware settings.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new package, omnia-mcu-firmware, containing firmware binaries for
the microcontroller on the Turris Omnia router.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the MCU driver on CZ.NIC's Turris Omnia. This adds
the ability to do a true board poweroff, and to configure various
features (for example the user may configure that after poweroff, the
router should automatically wake up at a specific time).
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
This backports patches
dt-bindings: firmware: add cznic,turris-omnia-mcu binding
platform: cznic: Add preliminary support for Turris Omnia MCU
platform: cznic: turris-omnia-mcu: Add support for MCU connected GPIOs
platform: cznic: turris-omnia-mcu: Add support for poweroff and wakeup
platform: cznic: turris-omnia-mcu: Add support for MCU watchdog
platform: cznic: turris-omnia-mcu: Add support for MCU provided TRNG
ARM: dts: turris-omnia: Add MCU system-controller node
ARM: dts: turris-omnia: Add GPIO key node for front button
platform: cznic: turris-omnia-mcu: Depend on OF
platform: cznic: turris-omnia-mcu: Depend on WATCHDOG
platform: cznic: turris-omnia-mcu: fix Kconfig dependencies
that will be released in 6.11 into mvebu/patches-6.6.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
This target doesn't actually use NAND.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16001
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit f444dea428.
It seems that some devices using GPIO WDT have really short WDT timeouts
and when using module_platform_driver registration it happens too late
and thus WDT will timeout and reset the board.
So, for now lets return the postcore_initcall hack for now.
Fixes: f444dea428 ("ath79: remove GPIO driver earlier registration hack")
Signed-off-by: Joan Moreau <jom@grosjo.net>
Link: https://github.com/openwrt/openwrt/pull/16035
Signed-off-by: Robert Marko <robimarko@gmail.com>
Layerscape was switched to 6.6 kernel. Now is time to remove 6.1
support.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16037
Signed-off-by: Robert Marko <robimarko@gmail.com>
CI says patches need to be refreshed, so do so.
Fixes: 6bb334c5cf ("mediatek: fix u-boot env layout NVMEM definitions")
Link: https://github.com/openwrt/openwrt/pull/16051
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kirkwood was switched to 6.6. We can remove 6.1 support now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
generic.mk was commited by mistake. It isn't used. Let's remove it.
Fixes: ccbdb212f3 ("kirkwood: Add missing package dependency")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
Let's switch to kernel 6.6 for wide tests.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
Radxa ROCK Pi E v3.0 has a RTL8723DU Wi-Fi 4 on-board device. enable
it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S has a RTL8723DS Wi-Fi 4 on-board device. enable it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Import patch from mainline Linux to fix issue with PERST# signal
polarity.
Quote from commit message:
"This extra, very short, PERST# assertion + deassertion has been
reported to cause issues with certain WLAN controllers, e.g. RTL8822CE."
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Testing turned out that the HWRNG quality varies greatly on RK3566,
even on supposedly identical boards and SoC revisions.
Hence enable the HWRNG driver only on RK3568 for now.
Allow users to simply tune sample_count and quality to allow easily
testing results on different boards and SoCs.
Link: https://patchwork.kernel.org/project/linux-arm-kernel/cover/cover.1720969799.git.daniel@makrotopia.org/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a backport of netdev/net [1]/[2], expected to be in kernel 6.11
(if not backported to a stable branch).
Since 4fdc7bb8f1 (2024-06-14, switching ath79 from kernel 6.1 to 6.6),
the rtl8366s driver was made to write to bogus PHY MII registers on
ath79/netgear,wndr3800 and family, and likely on other systems using
this switch in a similar manner. The writes were directed to PHY 4 MII
registers 0x0d (13) and 0x0e (14). The rtl8366s data sheet claims these
registers are reserved. These register writes were causing the device to
not maintain link, track link status, or pass traffic on eth1 (labeled
WAN), as eth1 is connected to PHY 4.
0x0d is MII_MMD_CTRL, and 0x0e is MII_MMD_DATA. rtl8366s doesn't appear
to support MMD in any way, and certainly not via the IEEE 802.3 annex
22D "clause 45 over clause 22" protocol implemented by mmd_phy_indirect.
This patch intercepts those attempted register accesses and returns
-EOPNOTSUPP without touching the switch chip. This is implemented by
defining phy_driver::{read,write}_mmd as
genphy_{read,write}_mmd_unsupported for this PHY. A new PHY driver for
this PHY is introduced to achieve that, because this PHY was previously
using genphy_driver, and there is otherwise no clean way to declare lack
of support for these operations.
This was caused by kernel 9b01c885be36 (2023-02-13, in 6.3). The new
genphy_c45_read_eee_abilities call in genphy_read_abilities (called
during phy_probe) was causing an attempted MMD read of (MMIO_MMD_PCS,
MDIO_PCS_EEE_ABLE), which was transformed into an annex 22D
mmd_phy_indirect operation that performed MII register writes to
MII_MMD_CTRL, MII_MMD_DATA, and MII_MMD_CTRL again, followed by another
read from MII_MMD_DATA. This was enough to "scramble" the state of those
two MII registers, which are in fact not used for annex 22D MMD register
access on this device but are reserved and have some other function,
rendering the PHY unusable while so configured. The result of the
bungled MMD read attempt caused the genphy driver to incorrectly believe
that the PHY supported standard EEE, which led to several more attempted
MMD writes and reads, in turn being transformed into writes to these two
MII registers.
rtl8366s does support some pre-IEEE 802.3az EEE standard form of "Green
Ethernet" which the switch driver (local to OpenWrt) already has some
support for. No attempt is made to map the standard operations for this
device.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=225990c487c1
[2] https://lore.kernel.org/netdev/20240725204147.69730-1-mark@mentovai.com/
Fixes: https://github.com/openwrt/openwrt/issues/15981
Link: https://github.com/openwrt/openwrt/issues/15739
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16012
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi E v3.0 is a compact networking SBC[1] using the Rockchip
RK3328 SoC.
Hardware
--------
- Rockchip RK3328 SoC
- Quad A53 CPU
- 512MB/1GB/2GB DDR4 RAM
- 4/8/16/32GB eMMC
- Micro SD Card slot
- WiFi 4 and BT 4, or WiFi 5 and BT 5 (not supported yet)
- 1x 1000M Ethernet with PoE support (additional PoE HAT required)
- 1x 100M Ethernet
- 1x USB 3.0 Type-A port (Host)
- 1x 4-ring 3.5mm headphone jack
- 40 Pin GPIO header
[1] https://radxa.com/products/rockpi/pie
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15984
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
The hardware of these two models looks the same. This patch also
disabled unused i2c bus for WE3526.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
From the kernel log, we are using PCIe port 1 and 2.
dmesg:
```
[ 0.963526] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[ 0.970432] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 0.975312] mt7621-pci 1e140000.pcie: PCIE2 enabled
[ 1.071442] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 1.130382] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
```
Fixes: https://github.com/openwrt/openwrt/issues/16000
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for a dual-band AX1800 wall plug manufactured
by Shenzhen Century Xinyang Tech Co., Ltd.
CPU: Mediatek MT7621A (2 cores, 4 threads)
RAM: 256i MiB DDR3 (Samsung K4B2G1646F-BCNB)
ROM: 16 MiB SPI NOR (Winbond W25Q128JVPQ)
Wired: one gigabit RJ45 port (with green/yellow non-GPIO LEDs)
WiFi: Mediatek MT7905DAN + MT7975DN (DBDC 2x 2T2R)
Ant.: four 2 dBi external antennas (two 2.4GHz, two 5 GHz)
GPIO: tri-color status LED (GPIO 13, 14, 16);
reset button (GPIO 18)
Power: 12V 2-pin JST-XH on main PCB
110/220V AC to 12V1A DC on auxiliary PCB
UART: 115200 8n1, SMD pads available on the PCB as J4
pinout is [3v3] (Rx) (Tx) (Gnd)
MAC: 1C:BF:CE:xx:xx:xx (2.4 GHz, label)
1C:BF:CE:xx:xx:xx + 1 (ethernet [1])
1C:BF:CE:xx:xx:xx + 2 (5 GHz)
Original firmware is LEDE Reboot 17.01-SNAPSHOT (kernel 4.4.198)
with a few custom packages and a non-LuCI web interface.
Telnet and SSH are enabled, requiring an unknown root password [2].
Root password is also needed to access the router via UART console,
but passwordless telnet can be enabled via a trivial web exploit [3]
and then the root password can be removed by editing `/etc/shadow`.
Installation: First upload `sysupgrade` binary via web interface at
`http://192.168.188.1/settings.shtml` and wait until getting back to
the home screen (select network to extend). The installation fails
since the original firmware uses `swconfig` and recent versions of
OpenWrt use DSA. However, the sysupgrade file is uploaded correctly
and stored at `/tmp/upgrade.bin`, so it can be written to flash via
the web exploit [4] (both `mtd -r write` and `sysupgrade -Fn` work
fine). Passwordless telnet/ssh is not needed for installation.
Alternatively, use u-boot menu to load image via TFTP.
Notes:
- Device model in LEDE is "MediaTek MT7621 RFB (802.11ax,SNOR)".
- It is sold under several names, among them are Wodesys WD-R1802U,
Fenvi F-AX1802U, and EDUP EP-2971; the Wodesys brand was selected
since it is referenced in `/etc/banner` and `/etc/hosts`, and the
PCB is marked "WD518A V1.0".
- Instead of a standard ethernet transformer, the PCB has a few tiny
SMD coils.
[1] Original firmware sets ethernet MAC to 1C:BF:CE:E7:62:1D based on
offset `0x3fff4` in the Factory partition; since this is the same
MAC for all units, whereas WiFi MACs stored at offsets 0x6 and 0xc
are unique, it was decided to use <label MAC + 1> for ethernet.
[2] root:$1$7rmMiPJj$91iv9LWhfkZE/t7aCBdo.0:18388:0:99999:7:::
[3] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;killall telnetd;telnetd -l /bin/sh"
[4] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;mtd -r write /tmp/upgrade.bin firmware"
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15777
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport H616 DVFS support from linux-next.
Tested on the Orange Pi Zero 3 (H618 SoC).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15600
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Freescale procesor has Securite Engine driver called Talitos. [1]
This driver is already packaged for OpenWrt since commit
bf57f33f02 ("kernel: Allow talitos crypto
hw module selection"), but many users don't know about it.
Let's include this kernel module package to default packages as it was
recently done for MediaTek in commit 06c4fc6d5e
("kernel: enable inside secure driver for MediaTek platforms")
[1] https://cateee.net/lkddb/web-lkddb/CRYPTO_DEV_TALITOS.html
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/10557
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some devices lock up on PCIe initialization:
[ 64.309697] PCIe: Port 0 in endpoint mode, skipping.
[ 64.320496] PCIe: Initializing port 1
[ 64.325257] PCIe: BIST FAILED for port 1 (0xffffffffffffffff)
(system hangs here)
Given the ER contains no PCIe peripherals, has no way to attach any
and the stock kernel doesn't have PCIe support either, just disable it.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/15992
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16021
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16021
Signed-off-by: Robert Marko <robimarko@gmail.com>
NEC Aterm WG600HP is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG600HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG600HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : A4:12:42:xx:xx:A0 (config, 0x6 (hex))
WAN : A4:12:42:xx:xx:A1 (config, 0xc (hex))
2.4 GHz: A4:12:42:xx:xx:A2 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : A4:12:42:xx:xx:A3 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WR9500N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, Atheros AR9344 (SoC)
- 5 GHz : 3T3R, Atheros AR9380
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 12x/4x
- note : all LEDs are controlled by ath9k chip (AR9380)
- UART : pad on PCB (near shielded ath9k chip, white circle)
- assignment : 3.3V, GND, TX, RX from AR8327 side
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR9500N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR9500N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9380) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:60 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:61 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:62 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:63 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WR8750N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR8750N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR8750N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:00 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:01 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:02 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:03 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix PCIe initialization on AR934x by clearing PLL_PWD bit in addition to
PPL(PLL?)_RESET bit of AR724x.
Refresh patches by `make target/linux/refresh`.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The archs38 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix uninitialized variable warnings in function regcache_maple_drop
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel config for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT40A512M16TB-062ER 1GB
Ethernet: 2x 2.5G, 4x 1G Lan
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5.2GHz 4T4R
WiFi3: MT7915AN 5.8GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 5A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).
Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)
Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.
Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Radxa ROCK Pi S is a small in size, full in features SBC[1] using the
Rockchip RK3308B SoC.
Hardware
--------
- Rockchip RK3308B SoC
- Quad A35 CPU
- 256/512MB DDR3 RAM
- Optional 4/8GB eMMC
- Micro SD Card slot
- Optional WiFi 4 and BT 4 (not supported yet)
- 1x 100M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 2.0 Type-A port (Host)
- 1x USB 2.0 Type-C port (OTG)
- 2x 26 Pin GPIO header
[1] https://radxa.com/products/rockpi/pis
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Keenetic KN-3510 is a 2.4/5 Ghz band 11ax access point
Specification:
- System-On-Chip: MT7621AT
- CPU/Speed: 880 MHz
- Flash-Chip: Macronix MX30LF1G28AD-TI
- Flash size: 128 MiB
- RAM: 256 MiB
- 2x 10/100/1000 Mbps Ethernet
- PoE, 802.3af/at
- 4x internal antennas
- UART (J1) header on PCB (115200 8n1)
- WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps
- 2x LED, 2x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3510-squashfs-factory.bin"
to "KN-3510_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is exactly the same as WL-WN531G3 but with different partition layout and different MAC layout. Labeled as Quantum D4G Rev.: A2.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x Touchlink button
- 1x Turbo button
- 1x Wps button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 5x Blue leds (ethernet ports)
- 1x Power led
- 1x Wifi led
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:0F (factory @ 0x28)
WAN XX:XX:XX:XX:XX:10 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:11 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:12 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:11
Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15876
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In make menuconfig the name is [Amplifi Router HD], and
is missing Ubiquiti. Lets fix that by adding
DEVICE_VENDOR := Ubiquiti to generic-ubnt.mk so the name is:
[Ubiquiti Amplifi Router HD].
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15932
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.
Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- radio0 (Wi-Fi 2.4GHz) = label MAC + 1
- radio1 (Wi-Fi 5GHz) = label MAC + 2
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP6X10XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap6010dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/15941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove kmod-switch-rtl8366-smi from the package list, as it is still loaded
because kmod-switch-rtl8367b depends on it
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15757
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit fixes all errors reported by the checkpatch script. This
should make it easier to accept upstream this patch.
There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes two issues in the driver detach:
* double free of the same descriptor (upstream bug, backported in 66177c081f),
* releasing tx descriptor instead of rx (downstream bug).
The driver is compiled into the kernel that is why the error
is not visible in normal use.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Switch to new nvmem binding.
Also fixes a issue that the MAC address assigned to lan/wan was
reversed on eMMC boards.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Also use env variables exported by export_fitblk_rootdev() in
platform_copy_config().
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The target was marked source-only due do the broken Ethernet port on
some devices. With that fixed, it can be enabled again.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The new cpsw-switch driver reserves VLAN 1 for internal use, which
conflicts with the default network configuration of OpenWrt.
Switch back to the older cpsw driver to make the network connection on
the affected devices (BeagleBone Black and AM335x EVM) usable again.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Initramfs images are not supported by imagebuilder. With recent changes
to support Per Device Rootfs, we now generate an image and a vmlinux for
each Rootfs and these additional files are all shipped in the
imagebuilder tar.
Drop these new file and any vmlinux-initramfs as they are not used and
increase the final size of the imagebuilder archive.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The eMMC chip used in a small batch of these devices has issues operating
in HS400 mode. Reducing to HS200 mode works around the problem and does
not cause any noticeable performance penalties as smaller chips are not fast
enough to saturate the bus. Root cause analysis is pending.
Signed-off-by: Chad Monroe <chad@monroe.io>
Add entry for the BananaPi R3 mini to the platform_check_image()
function where it has been missing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There is no reason not to wire up the default netdev trigger for the SFP
LED since we have a separate SFP interface visible.
Link: https://github.com/openwrt/openwrt/pull/15927
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since we are trying to get rid of using labels, lets convert RB5009 to the
function/color combo.
Link: https://github.com/openwrt/openwrt/pull/15927
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, QCA8081 LED is never configured and the default configuration
has the LED polarity inverted so it will be lit when there is nothing
connected to the PHY.
So lets define the LED as active-low and configure the trigger via 01_leds.
Fixes: 85d9fd6f0e ("mvebu: add support for RB5009UG+S+IN")
Link: https://github.com/openwrt/openwrt/pull/15927
Signed-off-by: Robert Marko <robimarko@gmail.com>
stop "heartbeat" which happens before OpenWrt controls LED. instead,
just turn LED on.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15913
Signed-off-by: Robert Marko <robimarko@gmail.com>
The switch to the upstream mmc-mtk driver caused problems with MT7621
because of unstable too high clock frequency:
[ 49.643291] mmc0: error -88 whilst initialising SD card
[ 49.890047] mmc0: error -88 whilst initialising SD card
[ 50.142414] mmc0: error -88 whilst initialising SD card
[ 50.419218] mmc0: error -88 whilst initialising SD card
...
Fix this by reducing the clock speed to 48 MHz instead of 50 MHz, which
is also the value used in upstream Linux mt7621.dtsi.
With that change applied SD cards work as expected on MT7621 devices
also with the new driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Override max clock frequency to a stable value 24 MHz.
2. Use voltage regulator to control the power supply.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Now that the SDHC of MT762{0,1,8} has been supported upstream, it's
time to switch the default driver to the upstream one. We will still
keep the old driver for users to choose from.
Tested on HiWiFi HC5861 (MT7620A) and HiWiFi HC5661A (MT7628N).
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add all essential MTK SDHC properties to support the new mmc-mtk
driver. Since this driver relies on power regulators, we also
need to enable this feature for MT7620, just like MT762{1,8}.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: John Thomson <git@johnthomson.fastmail.com.au>
This is the upstream implementation of the MTK SD/SDIO/MMC card
reader driver. It is an alternative solution for the downstream
driver package "kmod-sdhci-mt7620".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: John Thomson <git@johnthomson.fastmail.com.au>
"cd-inverted" is an upstream documented property used to indicate
the CD line is actived high. We will introduce a new upstream SDHC
driver, and this change will make them compatible with each other.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.38
Removed target/linux/generic/hack-6.6/900-fix-build-to-handle-return-value.patch
which was introduced as a hacky attempt to fix an upstream issue related to 6.6.37.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/15879
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the past few years, we have received several reports about SPI
Flash not working properly. This is caused by excessively fast
clock frequency. It's really annoying to fix them one by one. Let's
reduce these aggressive frequencies to 50 MHz. This is a safe and
suggested value in the vendor SDK.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This commit adds support for Asus RT-AX89X BX revision.
WARNING: Only the BX revision boards (So B1, B2 etc) are supported because
AX revision boards use IPQ8074 v1 SoC which is unsupported.
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53 @ 2.2GHz
* RAM: 1024MB
* Storage: 256MB SLC NAND (Macronix MX30UF2G18AC)
* Ethernet:
* 5x 1G RJ45 ports via QCA8337 switch
* 3x 1G RJ45 ports via internal switch (QCA8075 PHY)
* 1x 10G RJ45 via internal switch (AQR113C PHY)
* 1x 10G SFP+ slot via internal switch
* WLAN:
* 2.4GHz 4x4
* 5GHz 8x8
* 8 external antennas
* USB: 2x USB 3.0 Type-A
* Buttons:
* Power switch
* WPS
* Reset
* Wireless ON/OFF
* LED ON/OFF
LED-s:
* Power
* Wi-Fi
* WAN
* 10G
* SFP+
Power:
* 19.5V via DC jack
Installation instructions:
--------------------------
1. Flash temporary OpenWrt initramfs:
* Flash openwrt-qualcommax-ipq807x-asus_rt-ax89x-initramfs-factory.trx
via the stock firmware.
Administration -> Firmware Upgrade -> Manual Firmware update (Upload)
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
2. Sysupgrade from OpenWrt initramfs:
* Copy openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin to
/tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin of
the running initramfs image.
* Simply sysupgrade -n /tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
PMD Global Transmit Disable bit should be cleared for normal operation.
This should be HW default, however I found that on Asus RT-AX89X that uses
AQR113C PHY and firmware 5.4 this bit is set by default.
With this bit set the AQR cannot achieve a link with its link-partner and
it took me multiple hours of digging through the vendor GPL source to find
this out, so lets always clear this bit during .config_init() to avoid a
situation like this in the future.
aqr107_wait_processor_intensive_op() is moved up because datasheet notes
that any changes to this bit are processor intensive.
This is a modified version of patch that got merged upstream as AQR113C
has a separate config_init() upstream.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X has an external QCA8337 switch that has built-in
internal ethernet PHY-s that are supported by the QCA83XX PHY driver so
lets enable it.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X has an Qualcomm QCA8337 switch used to provide additional
1G copper ports, so lets enable qca8k in order to utilize DSA instead of
relying on SSDK for it.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X is using GPIO bitbanged MDIO on newer HW revisions, so lets
enable it in kernel config.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that newer SSDK is now expecting the switch node to be a subnode
of "ess-instance" node which also contains "num_devices" as the number of
switches as you can also have external switches connected.
Asus RT-AX89X is even more peculiar as its bootloader has a hardcoded path
to enable if on that revision there is an AQR113 connected to port 6 of the
switch.
So, lets move the current switch node under ess-instance as otherwise it
seems that SSDK is having some issues parsing the UNIPHY mode properly as
I am getting the following:
[ 6.981404] _adpt_hppe_instance1_mode_get[3275]:ERROR:port 6 doesn't support port_interface_mode 9
Which should not happen as that port has the mode set to 13.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Exclude additional initramfs image for Netgear RAX120v2 when no
initramfs image are compiled to fix build error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Trying to compile x86 or x86_64 on macOS will fail with:
openwrt/build_dir/target-x86_64_musl/linux-x86_64/linux-6.6.36/tools/include/linux/rbtree.h:21:10: fatal error: 'linux/stddef.h' file not found
After some digging, it seems that we dropped the old 212-tools_portability
patch when 6.6 x86 support was added, then Felix added back some parts of
it in ("kernel: fix tools build breakage on macos with x86") but trying to
build x86 kernels will still fail.
So, lets add more of the required changes from the 212-tools_portability
patch so that x86 kernels build on macOS.
Fixes: 69b145188f ("generic: 6.6: Removal of tools_portability.patch already included in kernel 6.6")
Link: https://github.com/openwrt/openwrt/pull/15904
Signed-off-by: Robert Marko <robimarko@gmail.com>
When building the kernel with -Wmaybe-uninitialized, GCC reports this
warning:
block/partitions/fit.c: In function 'parse_fit_partitions':
block/partitions/fit.c:164:3: warning: 'images' may be used uninitialized in this function [-Wmaybe-uninitialized]
164 | printk(KERN_ERR "FIT: Cannot find %s node: %d\n", FIT_CONFS_PATH, images);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
It appears to be a copy paste error. It's the "config" variable that is
supposed to be printed.
Fixes: e6aac8d98f ("image: add support for building FIT image with filesystem")
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
fit size should be rounded up instead of rounding down first and adding
a block. Otherwise the calculated size is one block more than needed
when fit size is exactly multiples of one block size.
Fixes: 9a863f803e ("kernel: mtdsplit: add support for FIT image")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Since 6.6 is now default, drop 6.1 support.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Let's switch the lantiq target to use kernel 6.6 by default.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports the fix for the broken "nosmp" and "maxcpus=0" cmdline
params.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since 6.1 is now default, drop 5.15 support.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patch implementing operations to get and set flow-control link
parameters of mtk_eth_soc via ethtool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.36..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
WiFi calibration data is already obtained via in-kernel NVMEM framework.
There is no need to also do so in userspace.
Fixes: dd58ad968a ("mediatek/filogic: add OpenWrt One support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The new numberspace base starts from 512 instead of 0. The number
base seems come from the kernel symbol CONFIG_GPIOLIB_FASTPATH_LIMIT.
Suppress warning:
gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The numberspace base has been changed since 6.6 kernel:
chip_num chip0 chip1 chip2 (32 gpios per bank)
old base 480 448 416
new base 512 544 576
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This commit adds support for TP-LINK RE6000XD.
The device is quite similar to the Mercusys MR90X V1,
except only 3 LAN ports and more LEDs.
So thanks to csharper2005 for doing all the groundwork.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (LAN3 2.5Gbps), 2xGbE (LAN 1Gbps, LAN1,
LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x signal
blue/red, 3 LAN blue gpio-controlled
Button: 2 (Reset, WPS)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, ubi0
partition contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART), unpopulated
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
Disassemble: rm the 2 screws at the bottom and the one at the backside.
un-clip the case starting at the edge above the LEDs.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot openwrt-mediatek-filogic-tplink_re6000xd-initramfs-kernel.bin bootm
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Notice: while I was successfull at activating ssh (as described
here:
https://www.lisenet.com/2023/gaining-ssh-access-to-tp-link-re200-wi-fi-range-extender/)
Unfortunately I haven't found the correct root password.
Looks like they are using a static password
(md5crypt, salt + 21 characters) that is not the web
interface admin password.
The TP-LINK RE900XD looks like the very same device,
according to the pictures and the firmware.
But I haven't checked if the OpenWrt firmware works as well
on that device.
The second ubi partition (ubi1) is empty and there is no known
dual-partition mechanism, neither in u-boot nor in the stock firmware.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
