new versions of the device have NAND with 8bit ECC
which was not yet supported before. This change removes
ECC restrictions.
Signed-off-by: Alexander Friese <af944580@googlemail.com>
(cherry picked from commit 6b11f0ec83)
Hardware
--------
CPU: Qualcomm IPQ4018
RAM: 256M
Flash: 16MB SPI-NOR (W25Q128)
128MB SPI-NAND (XTX)
WiFi: 2T2R (2GHz 802.11n ; 5 GHz 802.11ac)
ETH: 4x LAN ; 1x WAN (Gigabit)
CELL: Quectel RG501Q 3G/4G/5G
UART: Available on the goldfinger connector (Pinout silkscreened)
115200 8N1 3V3 - Only connect RX / TX / GND
Installation
------------
1. Enable SSH in the Teltonika UI
(System --> Administration --> Access Control)
2. Check from which partition set the device is currently running from.
$ cat /proc/boot_info/rootfs/primaryboot
In case this output reads 0, install a Software update from Teltonika
first. After upgrade completion, check this file now reads 1 before
continuing.
2. Transfer the OpenWrt factory image to the device using scp. Use the
same password (user root!) as used for the Web-UI.
$ scp -O openwrt-factory.bin root@192.168.1.1:/tmp
3. Connect to the device using ssh as the root user.
4. Install OpenWrt by writing the factory image to flash.
$ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin
5. Instruct the bootloaer to boot from the first partition set.
$ echo 0 > /proc/boot_info/rootfs/primaryboot
$ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin
$ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin
$ mtd write /tmp/bootconfig.bin /dev/mtd2
$ mtd write /tmp/bootconfig1.bin /dev/mtd3
6. Reboot the device.
$ reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 844bb4bfad)
These are used by both the armsr (EFI boot) and
layerscape targets for phylink-controlled SFP
support on NXP DPAA2 platforms (LS1088,LS2088,LX2160).
This is in place of commit a7bd96c98f
("layerscape: add patches for SFP support on DPAA2 platforms")
in the main branch. armsr in main started at kernel 6.1
so there is not an equivalent 5.15 commit to cherry pick.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
All the tools (e.g fw_setenv, ubiupdatevol) and config (fw_env.config)
needed for sysupgrade are already included in /lib/upgrade/stage2
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 094c37708a)
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.
Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).
It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 8e7ba6fbae)
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.
See the online manual for more information, including the
flash layout[2].
This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.
We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
(cherry picked from commit af0546da34)
The mdio bus is used to control externel switch. In most cases, they are
disabled, which is the normal behavior. Treating this as an error makes
no sense, so we need to change the notification level from error to info.
Fixes: a2acdf9607 ("ramips: mt7620: remove useless GMAC nodes")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 285f0668f4)
This commit adds headers to the patches, so they can be applied with the
git am command.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
(cherry picked from commit 5d51079fd0)
The maximum offset that can be supported is 0x20000000
Do not override it to to something bigger than that on MT7621, as that could
cause issues based on the fixed memory mappings. This makes the last 64 MB
RAM unusable on MT7621 devices with 512 MB but avoids incurring a heavy
performance hit
Fixes: cd2b74e01e ("ramips: mt7621: disable highmem support and remove highmem offset patch")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a110de8152)
Hardware
--------
CPU: Mediatek MT7981
RAM: 512M DDR4
FLASH: 256M NAND
ETH: MaxLinear GPY211 (2.5GbE N Base-T)
WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN: 1x Reset
LED: 1x Multi-Color
UART Console
------------
Available below the rubber cover next to the ethernet port.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.
$ atnf nwa50axpro-openwrt-initramfs.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd9 get-status
$ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd9 set-active-image 0
Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.
$ sysupgrade -n image.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f0445746f6)
U-Boot complains that the overlayed DT needs relocation, so set
DEVICE_DTS_LOADADDR to have it relocated.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit b1d10e0174)
removed redundant eeprom partition nodes from
cn7130_ubnt_edgerouter-4.dts and cn7130_ubnt_edgerouter-6p.dts
as they are identically defined in cn7130_ubnt_edgerouter-e300.dtsi.
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(integrated eeprom referenced node in the .dtsi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 700f11aaad)
The MAC addresses should be read from 3rd MTD partition,
but only two MTD partitions are populated.
To fix it, a partitions node has to surround the partition
nodes in device tree.
Tested with Edgerouter 6P
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(fixed checkpatch complains)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 2b1d7965c7)
LEDs on Edgerouter 6P didn't work correctly:
blue /white LED swapped, on/off state inverted
Fixed in device tree:
swap the GPIO ports for power:blue and power:white LEDs
change LED activity from LOW to HIGH
Tested on Edgerouter 6P
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(cherry picked from commit 9009672930)
there's a new symbol NVMEM_IMX_OCOTP_ELE that needs to be defined.
otherwise the build will fail:
| i.MX On-Chip OTP Controller support (NVMEM_IMX_OCOTP_ELE) [N/m/y/?] (NEW)
| make[6]: *** [scripts/kconfig/Makefile:77: syncconfig] Error 1
| make[5]: *** [Makefile:628: syncconfig] Error 2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The PHY driver now uses regmap created from pio syscon, we no longer
need the boottrap device.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f321a49fd5)
Backport in-SoC Gigabit Ethernet PHY driver instead of carrying the
driver in files-5.15.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9fac590096)
The PHY driver needs to read a register containing the values of the
bootstrap pins (which happen to be the PHY LEDs) to determine the LED
polarities. Allow regmap access to first pinctrl bank by adding the
'syscon' compatible, and reference the pinctrl in the MDIO bus where
the PHY driver will look for it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1f1e0b1144)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: W25N01GVZEIG 128MB
RAM: NT5CB128M16JR-FL 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Flash instructions:
1. PC run command: "telnet 192.168.124.1 99"
Username: H3C, password is the web login
password of the router.
2. Download preloader.bin and bl31-uboot.fip
3. PC run command: "python3 -m http.server 80"
4. Download files in the telnet window:
"wget http://192.168.124.xx/xxx.bin"
Replace xx with your PC's IP and
the preloader.bin and bl31-uboot.fip.
5. Flushing openwrt's uboot:
"mtd write xxx-preloader.bin BL2"
"mtd write xxx-bl31-uboot.fip FIP"
6. Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
7. Download initramfs image, reboot router,
waiting for tftp recovery to complete.
8. After openwrt boots up, perform sysupgrade.
Note:
1. The u-boot-env partition on mtd is empty,
OEM stores their env on ubi:u-boot-env.
2. Back up all mtd partitions before flashing.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit e78d1a06c8)
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.
Related: https://github.com/openwrt/openwrt/pull/5084
For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.
Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
boot, then hold the reset button for 10 seconds. This is needed
because sysupgrade in the stock firmware will attempt to preserve its
configuration using sysupgrade.tgz.
See https://github.com/openwrt/openwrt/pull/4182
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit 73de41898f)
These fields are used for EAX12 and EX6250v2 series, and perhaps other
devices. Compatibility is preserved with the WAX202 and WAX206.
In addition, adds the related vars to DEVICE_VARS so that the variables
work correctly with multiple devices.
References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz
* tools/imgencoder/src/gj_enc.c
Contains code that generates the encrypted image.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit 0a1ebccc87)
Mikrotik RB951 router has a buzzer on the board, which makes annoying noises
due to the interference caused by PoE input or Wifi transmission
when no GPIO pin state is set.
I added buzzer node to device's DTS in order to set deault level to 1
and to provide easier access for it.
Signed-off-by: Pavel Pernička <pernicka.pa@gmail.com>
(cherry picked from commit dac0a133cf)
MikroTik RB951G-2HnD is a wireless SOHO router that was previously
supported by the ar71xx target, see commit 7a709573d7 ("ar71xx: add
kernel support for the Mikrotik RB951G board").
Specifications
--------------
- SoC: Atheros AR9344 (600 MHz)
- RAM: 128 MB (2x 64 MB)
- Storage: 128 MB NAND flash (various manufacturers)
- Ethernet: Atheros AR8327 switch, 5x 10/100/1000 Mbit/s
- 1x PoE in (port 1, 8-30 V input)
- Wireless: Atheros AR9340 (802.11b/g/n)
- USB: 2.0 (1A)
- 8x LED:
- 1x power (green, not configurable)
- 1x user (green, not configurable)
- 5x GE ports (green, not configurable)
- 1x wireless (green, not configurable)
- 1x button (restart)
Unlike on the RB951Ui-2HnD, none of the LEDs on this device seem to be
GPIO-controllable, which was also the case for older OpenWRT versions
that supported this board via a mach file. The Ethernet port LEDs are
controlled by the switch chip.
See https://mikrotik.com/product/RB951G-2HnD for more details.
Flashing
--------
TFTP boot initramfs image and then perform sysupgrade. Follow
common MikroTik procedures at https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
(cherry picked from commit db02cecd6a)
Mikrotik RouterBOARD 951Ui-2HnD and Mikrotik RouterBOARD RB951G-2HnD are
very similar devices. Extract the DTS bits that are identical for these
two boards to a separate DTSI file.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
(cherry picked from commit c6ef417094)
Fixes: 4970dd027b ("bcm47xx: revert bgmac back to the old limited max frame size")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 83aeb0bbd4)
This includes some driver changes and support for fixed cells layout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 07bdc55515)
Calling rtl822x_probe() on phy devices which uses the rtl822x_read_mmd()
and rtl822x_write_mmd() functions makes no sense and the probe ends with
an EOPNOTSUPP error.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit 5af7d47cd7)
Migrate to "new" image generation method. Device profiles will be generated
based on image/Makefile instead of profiles/ , which will also allow to
automatically build images for all supported devices via buildbot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The upstream board-2.bin file in the linux-firmware.git
repository for the QCA4019 contains a packed board-2.bin
for this device for both 2.4G and 5G wifis. This isn't
something that the ath10k driver supports.
Until this feature either gets implemented - which is
very unlikely -, or the upstream boardfile is mended
(both, the original submitter and ath10k-firmware
custodian have been notified). OpenWrt will go back
and use its own bespoke boardfile. This unfortunately
means that 2.4G and on some revisions the 5G WiFi is
not available in the initramfs image for this device.
Fixes: #12886
Reported-by: Christian Heuff <christian@heuff.at>
Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 75505c5ec7)
The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can
be powered via PoE or a DC barrel connector (12V). Connecting to the
UART requires fine soldering and careful manipulation of any soldered
wires.
Device details:
* SoC: MT7621AT
* Flash: 16 MiB SPI NOR
* RAM: 256 MiB DDR3L
* Wi-Fi:
* MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2
* Two stamped metal antennas (ANT1, ANT2)
* One PCB antenna (ANT3)
* One unpopulated antenna (ANT4)
* Ethernet:
* 1× 10/100/1000 Mbps port with PoE
* LEDs:
* Array of four blue LEDs with one control line
* Buttons:
* Reset
* Board test points:
* UART: next to CPU RF-shield and power circuits
* JTAG: under CPU RF-shield (untested)
* Watchdog: 3PEAK TPV706 (not implemented)
Althought three antennas are populated, the MT7905DA does not support
the additional Rx chain for background DFS detection (or Bluetooth)
according to commit 6cbcc34f50 ("ramips: disable unsupported
background radar detection").
MAC addresses:
* LAN: 48:22:54:xx:xx:a2 (device label)
* WLAN 2.4 GHz: 48:22:54:xx:xx:a2
* WLAN 5 GHz: 48:22:54:xx:xx:a3
The radio calibration blob stored in flash also contains valid MAC
addresses for both radio bands (OUI 00:0c:43).
Factory install:
1. Enable SSH on the device via web interface
2. Log in with SSH, and run `cliclientd stopcs`
3. Upload -factory.bin image via web interface. It may be necessary to
shorten the filename of the image to e.g. 'factory.bin'.
Recovery:
1. Open the device by unscrewing four screws from the backside
2. Carefully remove board from the housing
3. Connect to UART (3.3V):
* Find test points labelled "VCC", "GND", "UART_TX", "UART_RX"
* Solder wires to test points or connect otherwise. Be careful not
to damage the PCB e.g. by pulling on soldered wires.
* Open console with 115200n8 settings
4. Interrupt bootloader and use tftpboot to start an initramfs:
setenv ipaddr $DEVICE_IP
setenv serverip $SERVER_IP
tftpboot 84000000 openwrt-initramfs-kernel.bin
bootm
DO NOT use saveenv to store modified u-boot environment variables. The
environment is saved at flash offset 0x30000, which erases part of the
(secondary) bootloader.
The device uses two bootloader stages. The first stage will load the
second stage from a uImage stored at flash offset 0x10000. In case of
a damaged second stage, the first stage should allow uploading a new
image via y-modem (untested).
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 11588c52b4)
The NETGEAR WAX220 employs NMBM on SPI-NAND. In order to avoid dealing
with invalid factory data, enable NMBM in the area preceding the UBI
volume.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 92eec257dd)
CONFIG_FRAME_WARN value is set by config/Config-kernel.in based on the
target type dynamically since commit:
16a2051 ("kernel: Set CONFIG_FRAME_WARN depending on target").
However, CONFIG_FRAME_WARN was not set to get filtered out so it ended up
in multiple target configs during refreshes.
So, lets filter out CONFIG_FRAME_WARN as its set dynamically to prevent it
ending up in more target configs.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 7a9a4168bb)
This commit adds support for following wireless routers:
- Beeline SmartBox PRO (Serсomm S1500 AWI)
- WiFire S1500.NBN (Serсomm S1500 BUC)
This commit is based on this PR:
- Link: https://github.com/openwrt/openwrt/pull/4770
- Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.
My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1
Common specification
--------------------
SoC: MediaTek MT7621AT (880 MHz, 2 cores)
Switch: MediaTek MT7530 (via SoC MT7621AT)
Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe: via J2 on PCB, not soldered on the board
UART: J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek
Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1
WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1
MAC address table (PRO)
-----------------------
use address source
LAN *:23 factory 0x1000 (label)
WAN *:24 factory $label +1
2g *:23 factory $label
5g *:25 factory $label +2
MAC addresses (NBN)
-------------------
use address source
LAN *:0e factory 0x1000
WAN *:0f LAN +1 (label)
2g *:0f LAN +1
5g *:10 LAN +2
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
a. OpenWrt - that's OK, the mission accomplished
b. Stock firmware - install Stock firmware (to switch booflag from
Sercomm0 to Sercomm1) and then OpenWrt factory image.
Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
reboot
2. Install stock firmware via the web OEM firmware interface
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 2d6784a033)
This commit moves a part of the code from the "sercomm-factory-cqr" recipe
to the separate "sercomm-mkhash" recipe. This simplifies recipes and
allows insert additional recipes between these code blocks (required for
the future support for Beeline SmartBox PRO router).
dd automatically fills the file by 0x00 if the filesize is less than
offset where we start writing. We drop such dd command so we need to add
--extra-padding-size 0x190 to the sercomm-pid.py call.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit f560be583a)
This commit adds support for Mercusys MR90X(EU) v1 router.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled
LEDs on ethernet ports
Button: 1 (Reset)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
The R3 (TX line) and R6 (RX line) are absent on the PCB. You should
solder them or solder the jumpers.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Once inside OpenWrt, set / update env variables:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial@11002000
fw_setenv stdin serial@11002000
fw_setenv stdout serial@11002000
fw_setenv tp_boot_idx 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Installation (without UART)
---------------------------
1. Login as root via SSH (router IP, port 20001, password - your web
interface password)
2. Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and
SSH settings from the p.1)
3. Add a newline after "#!/bin/sh":
telnetd -l /bin/login.sh
4. Save "65-iptv" file
5. Toggle "IPTV/VLAN Enable" checkbox in the router web interface and
save
6. Make sure that telnetd is running:
netstat -ltunp | grep 23
7. Login via telnet to router IP, port 23 (no username and password are
required)
8 Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the
router (e.g., using WinSCP and SSH settings from the p.1)
9. Stock busybox doesn't contain ubiupdatevol command. Hence, we need to
download and upload the full version of busybox to the router. For
example, from here:
https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64
Upload busybox-arm64 to the /tmp dir of the router and run:
in the telnet shell:
cd /tmp
chmod a+x busybox-arm64
10. Check "initramfs-kernel.bin" size:
du -h initramfs-kernel.bin
11. Delete old and create new "kernel" volume with appropriate size
(greater than "initramfs-kernel.bin" size):
ubirmvol /dev/ubi0 -N kernel
ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB
12. Write OpenWrt "initramfs-kernel.bin" to the flash:
./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin
13. u-boot-env can be empty so lets create it (or overwrite it if it
already exists) with the necessary values:
fw_setenv baudrate 115200
fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
fw_setenv fdtcontroladdr 5ffc0e70
fw_setenv ipaddr 192.168.1.1
fw_setenv loadaddr 0x46000000
fw_setenv mtdids "spi-nand0=spi-nand0"
fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
fw_setenv netmask 255.255.255.0
fw_setenv serverip 192.168.1.2
fw_setenv stderr serial@11002000
fw_setenv stdin serial@11002000
fw_setenv stdout serial@11002000
fw_setenv tp_boot_idx 0
14. Reboot to OpenWrt initramfs:
reboot
15. Login as root via SSH (IP 192.168.1.1, port 22)
16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
17. Run sysupgrade:
sysupgrade -n /tmp/sysupgrade.bin
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery (UART)
---------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot initramfs-kernel.bin
bootm
4. Do what you need (restore partitions from a backup, install OpenWrt
etc.)
Stock layout
------------
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format
----------------
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 00:eb:xx:xx:xx:be | label |
| LAN | 00:eb:xx:xx:xx:be | label |
| WAN | 00:eb:xx:xx:xx:bf | label+1 |
| WLAN 2g | 00:eb:xx:xx:xx:be | label |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac". OEM wireless eeprom is also there (file
"MT7986_EEPROM.bin").
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit e4fe3097ef)
[Fix merging conflict]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The ZTE MF287+ is a LTE router used (exclusively?) by the network operator
"3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only
difference is the LTE modem)
Specifications
==============
SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287)
WiFi: 802.11a/b/g/n/ac SoC-integrated
MAC addresses
=============
LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1
Installation
============
Option 1 - TFTP
---------------
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x82000000 openwrt.bin
bootm 0x82000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:
ubiattach -m14
cat /dev/ubi0_0 > /tmp/ubi0_0
cat /dev/ubi0_1 > /tmp/ubi0_1
Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.
Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N kernel
Option 2 - From stock firmware
------------------------------
The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.
The exploit will be available at the device wiki page.
Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".
ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".
Complete commands:
cd /tmp
tftp -g -r factory.bin 192.168.0.22
cat /proc/driver/sensor_id
flash_erase /dev/mtd13 0 0
dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072
Afterwards, reboot your device and you should have a working OpenWrt
installation.
Restore Stock
=============
Option 1 - via UART
-------------------
Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.
Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.
ubiattach -m 14
ubirmvol /dev/ubi0 -N kernel
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N rootfs_data
ubimkvol /dev/ubi0 -N kernel -s $kernel_length
ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1
Option 2 - from within OpenWrt
------------------------------
This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.
Follow the commands from Option 1 to flash back to stock.
LTE Modem
=========
The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.
Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit f70ee53b08)
Some ZTE devices require the gpio-restart driver to support restarting the
LTE modem along with OpenWrt
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 9ffdaa7fa1)
Hardware
--------
SOC: MediaTek MT7986
RAM: 1024MB DDR3
FLASH: 128MB SPI-NAND (Winbond)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the WAX220. Conect to the serial console,
interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.2.1
$ setenv serverip 192.168.2.2
$ tftpboot openwrt.bin
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
(cherry picked from commit 984786a2f7)
After migrating to kernel 5.15, upgrading causes the units to become
soft-bricked, hanging forever at the kernel startup.
Kernel size limitation of 4000000 bytes is suspected here, but this is
not fully confirmed.
Disable the images to protect users from inadvertent bricking of units,
because recovery of those is painful with Cisco's U-boot, until the root
cause is found and fixed.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 9d64cc068f)
Previously both lan1 and lan2 leds were wrongly labelled as lan2.
Moreover they were connected to the wrong lan port.
Fixes 8fde82095b ("ramips: add support for Wavlink WL-WN535K1")
Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com>
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
(cherry picked from commit c71dada926)
Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G)
modems.
Specifications:
* SoC: MediaTek MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* Wi-Fi:
* MediaTek MT7603E : 2.4Ghz
* MediaTek MT7613BE : 5Ghz
* Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* M.2: 1x slot with USB&SIM
* EM7455/EM12-G/EM160R/RM500Q-AE
* USB: 1x 3.0 Type-A port
* External storage: 1x microSD (SDXC) slot
* UART: console (115200 baud)
* LED:
* 1 power indicator
* 1 WLAN 2.4G controlled (wlan 2G)
* 3 SoC controlled (wlan 5G, wwan, internet)
* 5 per Eth phy (4xLAN + WAN)
MAC Addresses:
* LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex))
* WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex))
* 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex))
* 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex))
Installation:
* Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.
Recovery Mode:
* Press reset button, power up the device, wait for about 10sec.
* Upload sysupgrade image through the firmware recovery mode web page at
192.168.1.1.
Signed-off-by: Kim DoHyoung <azusahmr@k-on.kr>
(cherry picked from commit 0bbd5699c8)
Hardware
========
CPU Qualcomm Atheros QCA9558
RAM 256MB DDR2
FLASH 2x 16M SPI-NOR (Macronix MX25L12805D)
WIFI Qualcomm Atheros QCA9558
Atheros AR9590
Installation
============
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x80060000 ap115.bin; go 0x80060000"
$ setenv fb_openwrt "bank 1;
cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000"
$ setenv bootcmd "run fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1b467a902e)
The Arcadyan AR7516, AKA Orange Bright Box or EE Bright Box 1, is a wifi
fast ethernet router, 2.4 GHz single band with two internal antennas. It
comes with a horizontal stand black shiny casing.
Newer Bright Box 1 model stands vertically, and comes with a totally
different board inside, not compatible with this firmware.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 V7.5 @ 320Mhz
- RAM: 64 MB DDR2
- Flash: 8 MB SPI NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: Broadcom BCM43227 802.11bgn (onboard)
- USB: 1x 2.0
- ADSL: yes, unsupported
- Buttons: 2x
- LEDs: 9x, power LED is hardware controlled
- UART: yes
Installation in two steps, new CFE bootloader and firmware:
Install new CFE:
1. Power off the router and press the RESET button
2. Power on the router and wait some seconds
3. Release the RESET button
3. Browse to http://192.168.1.1, this web interface will offer both
firmware (“Software”) upgrade and bootloader upgrade; be sure to
use the bootloader section of the upload form.
4. Upload the new CFE (availabe at the wiki page)
5. Wait about a minute for flashing to finish and reboot into the new bootloader.
Install OpenWrt via new CFE web UI:
1. After installing the new CFE, visit http://192.168.1.1
2. Upload the Openwrt cfe firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry-picked from df8e4b6c2e)
This patch initially introduced in 94b4da9b4a
breaks mvebu devices when using vlan filtering with kernel 5.15 or 6.1,
it was working ok in 5.10.
With this patch, frame that should exit untagged from the switch exit tagged.
Running 'tcpdump -Q out -evnnli eth1' (eth1 being the dsa interface)
- with the hack, frame is sent directly to the
destination port 4 with VID 2, so the switch leave the tag as instructed:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode From CPU, target dev 0, port 4, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
- without the hack, frame is sent to the switch that
performs the forwarding decision and untagging:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode Forward, dev 1, port 0, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
Removing this patch makes my Turris Omnia usable with vlan filtering,
ie wifi device can talk to wired device again.
Using kernel 5.15 some broadcast/multicast traffic is still leaked
(on a VLAN 2 access port I see tagged VLAN 3 frame),
using kernel 6.1 fixes that.
People needing the extra performance should try the bridger package.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 244328b19c)
The NuCom R5010UNv2 is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 V7.5 @ 320Mhz
- RAM: 64 MB DDR2
- Flash: 16 MB SPI NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: Broadcom BCM43217 802.11bgn (onboard)
- USB: 1x 2.0
- Buttons: 2x
- ADSL: yes, unsupported
- LEDs: 7x
- UART: yes
Installation via CFE web UI:
1. Power off the router and press the RESET button
2. Power on the router and wait 12 or more seconds
3. Release the RESET button
4. Browse to http://192.168.1.1 and upload the Openwrt cfe firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 6cb3328b4f)
The data RAC is left disabled by the bootloader in some SoCs, at least in
the core it boots from. Enabling this feature increases the performance up
to +30% depending on the task.
The kernel enables the whole RAC unconditionally on BMIPS3300 CPUs. Enable
the data RAC in a similar way also for BMIPS4350.
Tested on DGND3700 v1 (BCM6368) and HG556a (BCM6358).
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 6d1265b148)
BMIPS_GET_CBR() returns an invalid address on some SoCs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 62cdca25ed)
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
(cherry picked from commit 8fcfb21b16)
Without it the WAN port won't be initialized properly.
Fixes: 8f578c15b3 ("rockchip: add NanoPi R2C support")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit d312f12b1a)
Move default cpufreq governor from ONDEMAND to PERFORMANCE. The temp
increase is just 2°C and Watt usage the change is minimal in the order
of additional millwatt. The SoC and krait in general looks to suffer for
some problem with cache scaling. To have better system stability, force
cpu freq and cache freq to the max value supported by the system. This
follows mvebu platform where cpufreq is broken and cause minimal
temp/watt increase.
User can still tweak the governor to ondemand using sysfs entry if
needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6f5ea752d7)
This reverts commit 60fc93b359.
Reenable devfreq and revert for both 5.15 and 6.1.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 37e4593213)
Power LED register is wrong at dts. Fix it.
Fixes: 9ceeaf4c6c ("brcm63xx: switch to hardware led controllers")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 0e01ba9361)
The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM63169
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 128 MB DDR
- Flash: 128 MB NAND
- LAN switch: Broadcom BCM53125, 5x 1Gbit
- Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn
- USB: 1x 2.0 (optional)
- Buttons: 2x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 47cc09aa7a)
All switch ports are labeled as port@address so let's follow the same pattern.
Fixes: ed79519b8d ("bmips: add support for Netgear DGND3700 v1, DGND3800B")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d9210c5ff7)
The Sercomm AD1018 is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB (v1) / 128 MB (v2) DDR
- Flash: 128 MB NAND
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43217 802.11bgn
- USB: 1x 2.0
- Buttons: 3x (reset)
- LEDs: yes
- UART: yes
Installation via OEM web UI:
1. Use the admin credentials to login via web UI
2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
3. Press "Update Firmware" button and wait some minutes until it finish
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 38ebb2eafd)
This is needed on devices like Sercomm AD1018 for booting recent kernels due
to bigger kernels.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 434434ca47)
The Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with
two external antennas. It comes with a coaxial HomePNA port.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 32 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 1x 2.0
- Buttons: 2x, 1 reset
- LEDs: 7x
- UART: yes
The HPNA hardware probably needs a firmware to make the coaxial port work.
In the OEM firmware, it's apparently sent with an utility (inhpna) through
the ethernet port.
Installation via CFE web UI:
1. Connect the UART serial port.
2. Power on the router and press enter at the console prompt to stop the
bootloader.
4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit e1a55de7a7)
Now that JFFS2 cleanmarkers are supported on the standard nand_do_upgrade
function we can start using it on bcm63xx.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from 60fc3bc948)
Now that JFFS2 cleanmarkers are supported on the standard nand_do_upgrade
function we can start using it on bmips.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from 464dfac049)
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit cdfcac6e24)
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 915e914cfa)
Some devices rename cferam bootloader using specific patterns and don't follow
broadcom standards for renaming cferam files. This requires supporting
different cferam file names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 8813edd8d9)
RISC-V is a new CPU architecture aimed to be fully free and open. This
target will add support for it, based on 5.15.
Supports running on:
- HiFive Unleashed - FU540, first generation
- HiFive Unmatched - FU740, current latest generation, PCIe
SD-card images are generated, where the partitions are required to have
specific type codes. As it is commonplace nowadays, OpenSBI is used as the
first stage, with U-boot following as the proper bootloader.
Specifications:
HiFive Unleashed:
- CPU: SiFive FU540 quad-core RISC-V (U54, RV64IMAFDC or RV64GC)
- Memory: 8Gb
- Ethernet: 1x 10/100/1000
- Console: via microUSB
HiFive Unmatched:
- CPU: SiFive FU740 quad-core RISC-V (U74, RV64IMAFDCB or RV64GCB)
- Memory: 16Gb
- Ethernet: 1x 10/100/1000
- USB: 4x USB 3.2
- PCIe: - 1x PCIe Gen3 x8
- 1x M.2 key M (PCIe x4)
- 1x M.2 Key E (PCIe x1 / USB2.0)
- Console: via microUSB
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
(cherry picked from commit a3469a90c4)
Now that the armvirt target supports real hardware, not just
VMs, thanks to the addition of EFI, rename it to something
more appropriate.
'armsr' (Arm SystemReady) was chosen after the name of
the Arm standards program.
The 32 and 64 bit targets have also been renamed
armv7 and armv8 respectively, to allow future profiles
where required (such as armv9).
See https://developer.arm.com/documentation/102858/0100/Introduction
for more information.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05 version of commit 40b02a2301)
The Amazon ENA network devices are also used on the
AWS Arm (Graviton) instance types, so move it from
the x86-only module file to the top level netdevices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 3a7c8fd15e)
The SMC91X family is a ISA-age Ethernet controller.
I'm not particularly sure what it's doing in armvirt/64,
as it's unlikely there is a QEMU or real hardware configuration
that exists with it.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit 214e94cddf)
tty0 is the default console for devices with screens/framebuffers.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit e41b82f619)
These Kconfig options are required to get a screen console
working with the VMware Fusion ARM (Apple Silicon) preview.
They are likely to be the same for other Arm standard
"desktop" hardware that may emerge.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of 83f564f746)
Add support for the dwmac (stmmac) variant used by Allwinner
Arm64 boards.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 847467a572)
Enable SATA support, which is used by the Server Base
System Architecture reference board[1].
Signed-off-by: Anton Antonov <Anton.Antonov@arm.com>
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://qemu.readthedocs.io/en/latest/system/arm/sbsa.html
(23.05/5.15 version of 26905c9612)
Also includes Advantech RSB-3720 (iMX8 Plus) support.
Signed-off-by: Anton Antonov <Anton.Antonov@arm.com>
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Re-sort into kernel config, move network into modules]
(23.05/5.15 version of commit 3efb3b801b)
These changes are to support other vendors that have SystemReady/EFI
support, including:
* Marvell Armada
** (This is speculative as I don't have a machine of my own to test)
* Amazon Graviton (tested bare-metal and virtualized instances)
* VMware (Fusion for ARM Mac preview)
* NXP/Freescale (Layerscape series not already selected)
* HiSilicon
* Allwinner/sunxi
* Rockchip (untested, options taken from arm64 defconfig)
To give an idea of the hardware certified for SystemReady,
see
https://www.arm.com/architecture/system-architectures/systemready-certification-program/ir
and
https://www.arm.com/architecture/system-architectures/systemready-certification-program/es
Other vendors that _should_ work include Marvell Octeon 10
and Ampere. I understand these systems should work
"out of the box" in ACPI mode but may require other drivers
(e.g PCIe NICs and storage controllers).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of c3151b6f04)
Tested with a Traverse Technologies Ten64 (LS1088A) board.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit 54bb95f879)
This fixes an issue with NXP's DPAA2 platforms (LS1088/2088/LX2160)
* A deadlock issue when attempting to detach the SFP management from
a PHY interface (e.g when trying to reboot). These issues were fixed
in kernel 6.2[1], but it's version does not cleanly apply onto 5.15.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - see patch series "Fix rtnl_mutex deadlock with DPAA2 and SFP modules",
https://patchwork.kernel.org/project/netdevbpf/cover/20221129141221.872653-1-vladimir.oltean@nxp.com/
ACPI support is required for Arm 'SystemReady' server and workstation
systems (and as an option on embedded platforms).
These config changes allow OpenWrt to boot in a QEMU virtual machine
with a UEFI/EDKII 'BIOS', but with no other hardware enabled yet.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of cb3bbbf00c)
This is useful for VMware's ARM64 products, e.g Fusion for M1/ARM Macs.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit f899e0e024)
Now that armvirt has been expanded to boot on more generic
ARM machines, remove the board and model name override.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 3d99314569)
U-Boot with EFI boot manager functionality will store
EFI boot order data on the ESP in the ubootefi.var file.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 9a76b99c1b)
The introduction of EFI support has changed how armvirt
images are generated. The kernel and filesystem binaries
can still be used as before with QEMU directly.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 97c5d317f5)
This interferes with the generation of the EFI stub section for
ARM32. As this target is not size constrained, disable the dead code
data elimination hack.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05 version of eb0e61285d)
EFI booting is used on newer machines compatible with the
Arm SystemReady specifications.
This commit restructures armvirt into a more 'generic'
target similar to x86.
See https://github.com/openwrt/openwrt/pull/4956
for a history of this port.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05 version of e0f06ddc23)
Having initramfs image built with same config as on buildbots:
CONFIG_TARGET_MULTI_PROFILE=y
CONFIG_TARGET_ALL_PROFILES=y
CONFIG_TARGET_PER_DEVICE_ROOTFS=y
Its currently impossible to flash/recover the device using that image as
losetup is missing:
root@OpenWrt:/# sysupgrade -v /tmp/openwrt-ipq807x-generic-prpl_haze-squashfs-sysupgrade.bin
...
/lib/upgrade/do_stage2: line 38: losetup: not found
Failed to detach all loop devices. Skip this try.
So lets fix it by including the needed utils for sysupgrade in
DEFAULT_PACKAGES set.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 07fe8bc62a)
BLOCKSIZE and PAGESIZE seems to be unused on qnap_301w and zyxel_nbg7815
device which use eMMC storage.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit fdea7cb617)
One is never to write to dev->addr directly. In 6.1 it will be a const and
with the newly enabled WERROR, we get a failing grade.
Lets fix this ahead of time.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
(cherry picked from commit d881f65da1)
We are missing a bunch of headers, which trigger errors on 6.1, probably
due to changed header-in-header dependencies. Best add them now.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
(cherry picked from commit 9fb1dbb1df)
Upstream DSA driver is exporting symbols with the same name as our
downstream swconfig driver, so lets rename the downstream symbols to make
them unique and avoid the conflict on 6.1 kernel.
Without this change, building 6.1 with kmod-switch-bcm53xx would conflict
with the B53 DSA driver and CI would fail.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit effccdd444)
The Comtrend AR-5381u is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB DDR
- Flash: 16 MB SPI NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43225 802.11bgn
- USB: 1x 2.0
- Buttons: 1x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit bcdf861519)
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the link reference to the
new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 52d86ac6eb)
The Comtrend WAP-5813n is a wifi gigabit router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 64 MB DDR
- Flash: 8 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM4322 802.11bgn
- USB: 1x 2.0 (optional)
- Buttons: 3x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit c3b1ef2dfd)
move wan port to gmac1 to achieve 2Gbps CPU bandwidth between wan and
lan on YunCore FAP-640
Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
(cherry picked from commit 47c2d50c03)
The Comtrend VR-3025un is a wifi gigabit router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 64 MB DDR
- Flash: 8 MB parallel NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43222 802.11bgn
- USB: 1x 2.0
- Buttons: 1x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the antenna.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 3baa45fbd8)
Align all the device tree files and follow the same criteria before more
devices are ported from bcm63xx and this goes out of control.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with
two internal antennas integrated in the main PCB.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 16 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 2x 2.0
- Buttons: 2x, 1 reset
- LEDs: 10x
- FXS: 2x
- UART: yes
Installation via CFE web UI:
1. Power off the router and make a temporal TX-RX shortcircuit on the
serial pins.
2. Power on the router and wait 3 or more seconds
3. Remove the TX-RX shortcircuit
4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the
firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The network configuration at first boot for TOZED ZLT S12 PRO lacks setting
up the LAN and WAN network interfaces. Address this. The WAN port is
advertised as WAN/LAN on the device and is put on LAN on stock firmware so
put it on LAN here as well.
Fixes: ce1f9fa625 ("ramips: add support for TOZED ZLT S12 PRO")
Reported-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit b61253f92a)
Instead of reference vlan and do strange subtraction, use the handy
struct_group() to create a virtual struct of the same size of the
members. This permits to have a more secure memset and fix compilation
warning in 6.1 where additional checks are done.
Fix compilation warning:
| inlined from 'psb6970_reset_switch' at drivers/net/phy/psb6970.c:275:2:
| ./include/linux/fortify-string.h:314:25: error: call to '__write_overflow_field'
| declared with attribute warning: detected write beyond size of field
| (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
| 314 | __write_overflow_field(p_size_field, size);
| | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|cc1: all warnings being treated as errors
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
(cherry picked from commit d69becd307)
DEVICE_DTC_FLAGS is more flexible and can be used in
place of APM821xx own DTB_SIZE.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit a5fc132aa3)
The Netgear DGND3700 v1 and DGND3800B are the same device but with
different factory firmwares. It's an xDSL wifi router with a slim black
shiny casing and 4 PCB internal antennas connected via UFL to a miniPCI
detachable card.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 128 MB DDR
- NOR Flash: 32 MB parallel (CFE and OS)
- NAND flash: 128 MB (empty)
- Ethernet LAN: 5x 1Gbit
- Wifi 2.4 GHz: Broadcom BCM43222 802.11bgn
- Wifi 5 GHz: Broadcom BCM43222 802.11abgn
- USB: 2x 2.0
- Buttons: 3x, 1 reset
- LEDs: 11x
- UART: yes
Installation via OEM web UI:
1. Open the Netgear administration web interface, by default:
http://192.168.0.1
user: admin
password: password
2. Look for "upgrade firmware" and proceed
3. Wait some minutes until it finishes
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Observa VH4032N is an xDSL wifi router with a vertical white casing
and two internal antennas connected via UFL.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400MHz
- RAM: 128 MB DDR
- Flash: 32 MB parallel NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4/5 GHz: onboard Broadcom BCM43222 802.11abgn
- USB: 3x 2.0
- Buttons: 2x, 1 reset
- LEDs: 8x, blue and red
- UART: 1x
Installation via OEM web UI:
1. Use the admin credentials to login via web UI
2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
3. Press "Update Firmware" button and wait some minutes until it finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
This allows booting bigger ramdisk images via TFTP at the cost of breaking 32M
RAM compatibility, but those devices have been unable to boot ramdisks on this
target for some time anyway due to not having enough RAM.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The MT7986 RFB was intended to use device tree overlays and for that
reason modified DTC_FLAGS. zyxel_ex5601-t0-stock later on probably
copied it from there. Both boards do not actually use device tree
overlays, so remove setting DTC_FLAGS from both.
The BPi-R3 does use device tree overlays, use DEVICE_DTC_FLAGS to give
it an extra 4kb of padding for overlays to be applied.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 98e6ea32a4)
Make sure there is an extra 4kb of padding to apply device tree overlays
on the BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7b536c4ec9)
If the board comes up with OpenWrt that means that the bootloader is
recent enough and knows about the new device tree overlays.
Using /etc/board.d/ is not enough in this case because it doesn't
overwrite existing configuration which may exist (and is fine to exist)
if the user updated with 'sysupgrade -F *.itb' and has kept
configuration. They would still need to manually set compat_version
even though the fact that the bootloader env has been updated can be
implied by the fact that the system has started.
Hence we can always set compat_version=1.1 for those two boards using
uci-defaults.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 25e27c4af3)
Sync device tree files for MT7986 boards with what landed in upstream
Linux tree to easy maintainance and also allow for a smooth update to
Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7a0ec001ff)
Use new device tree overlay mechanism for the BananaPi BPi-R64 board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 34bb33094a)
Now that it is possible to load several device tree overlays by
appending their config names to bootconf the uImage.FIT partition
parser need to discard everything after the first '#' character in
bootconf when looking up the config node to be used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 07bca1adaa)
The device tree file was in DOS format (CR-LF). Convert it to UNIX style.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d28534545e)
PCK and MCK should really be P=PMIC and M=MEM, which means that they
should effectively be CLK_PMIC and CLK_ARB.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0580747ada)
Use suggested fix for mediatek-cpufreq, patch will also be sent
upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7e93f520d6)
Recent libcap versions (>= 2.60) cause problems with BPF kselftests, so
backport an upstream patch that replaces libcap and drops the dependency.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit 04981c716a)
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and otherwise
identical to OrangePi R1 Plus.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 32d5921b8b)
[Removed patches for kernel 6.1]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
Note: booting from SPI is currently unsupported, you have to install
the image on a SD card.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit ab641efe69)
[Removed patches for kernel 6.1]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The compilation warning was triggered by wrongly set FRAME_WARN to 1024
even for 64bit. This was recently fix by correctly setting the
FRAME_WARN to 2048 for 64bit systems.
The compilation warning would still be triggered on 32bit system but the
actual code is never reached as ARCH_USE_GNU_PROPERTY is only set on
arm64 arch.
Drop the patch as kmalloc cause perf regression as suggested by upstream
maintainers.
Fixes: fa79baf4a6 ("generic: copy backport, hack, pending patch and config from 5.15 to 6.1")
Fixes: 5913ea1ba2 ("generic: 5.15: add pending patch fixing binfmt compilation warning")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 62338f4162)
Previously, CONFIG_LZ4_DECOMPRESS=y was selected by CONFIG_RD_LZ4 only.
When building kernel for initramfs, CONFIG_RD_LZ4 will be unset by
Kernel/SetInitramfs if the chosen compression method is not lz4, then
CONFIG_LZ4_DECOMPRESS will become a *module* in the newly generated
kernel config.
However, the newly added module won't be built after
38c150612c, so packaging kmod-lib-lz4
fails due to missing lz4_decompress.ko.
CONFIG_CRYPTO_LZ4=y makes CONFIG_LZ4_DECOMPRESS=y being selected w/o
CONFIG_RD_LZ4, so that the modules of the default kernel and initramfs
kernel are consistent.
Fixes: #12766
Fixes: 38c150612c ("build: revert 54070a1 (all kernels are >= 5.10)")
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
(cherry picked from commit cc87f6629b)
The device already has LED push button (KEY_LIGHTS_TOGGLE)
and exported GPIO control "led-light". This commit adds
button handler script for switching on/off all device LEDs.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit d955b41275)
Support newer IOMMU_V2 on AMD platforms, useful for DPDK and KVM.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
(cherry picked from commit 1eb02ce325)
Backport Russell King's series [1]
net: mvneta: reduce size of TSO header allocation
to pending-5.15 to fix random crashes on Turris Omnia.
This also backports two patches that are dependencies to this series:
net: mvneta: Delete unused variable
net: mvneta: fix potential double-frees in mvneta_txq_sw_deinit()
[1] https://lore.kernel.org/netdev/ZCsbJ4nG+So%2Fn9qY@shell.armlinux.org.uk/
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (squashed)
(cherry picked from commit 7b31c2e9ed)
it was reported that this flag caused the mx60
not to boot anymore.
Fixes: f095822699 ("apm821xx: convert legacy nand partition layou")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
commit 0c45ad41e1 changes ipq806x usb kmod name
from usb-phy-qcom-dwc3 to phy-qcom-ipq806x-usb, so
use new name.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
(cherry picked from commit 9314744350)
The MR600v2 does not find its rootfs if it is neither directly after the
kernel or aligned to an erase block boundary (64k).
This aligns the rootfs to 0x10000 allowing the device to boot again. Based
on investigation by forum user relghuar.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 46b51e9e99)
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
(cherry picked from commit 29a5cb7a8b)
This set the CONFIG_FRAME_WARN option depending on some target settings.
It will use the default from the upstream kernel and not the hard coded
value of 1024 now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 16a20512d8)
Currently, e2600ac-c1 cannot be built as the kernel is larger than the defined KERNEL_SIZE,
however, there is no bootloader limit for the kernel size so remove KERNEL_SIZE completely.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
[ improve commit title, fix merge conflict ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b764268acb)
Convert E2600ac c2 to DSA and enable it.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
[ rename port to more generic name ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 0dca52cf59)
Convert E2600ac c1 to DSA and enable it.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
[ rename port to more generic name ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 7f2ecab0f4)
The set_spi_clock_speed() function is not used, this causes a compile
warning which results in a build error with -WError.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2d5f3b3c4c)
read_page() need to return maximum number of bitflips instead of the
accumulated number. Change takes from upstream mt7621 u-boot [1].
* @read_page: function to read a page according to the ECC generator
* requirements; returns maximum number of bitflips
* corrected in any single ECC step, -EIO hw error
[1] https://lore.kernel.org/all/cover.1653015383.git.weijie.gao@mediatek.com/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 2fbb91d73f)
Management Complex (MC) userspace support is required for userspace
helpers working with DPAA2 objects exported by the Management Complex BUS.
Without it, there is the error:
```
root@OpenWrt:/# ls-addni dpmac.1
error: Did not find a device file
Restool wrapper scripts only support the latest major MC version
that currently is MC10.x. Use with caution.
error: Did not find a device file
```
This patch fixes it.
Suggested-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cherry picked from commit d04d6a82da)
The USXGMII driver in SDK was heavily refactored, some bugs have been
fixed and it has switched to use phylink_pcs. Follow up with changes
in SDK driver and sync our on-top-of-mainline driver with the SDK
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ba58245e83)
Use renamed build step names for all boards which were not handled by
commit c620409d58 ("mediatek: filogic: add uboot build for mt7981")
and now breaking the build.
Fixes: c620409d58 ("mediatek: filogic: add uboot build for mt7981")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 037ce27244)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT5CC128M16JR-EK 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Flash instructions:
1. Attach UART, boot the stock firmware until
the message about failsafe mode appears.
2. Enter failsafe mode by pressing "f" and "Enter"
3. Type "mount_root", then run
"fw_setenv bootmenu_delay 3"
4. Back up all mtd partitions before flashing.
5. Reboot, U-Boot now presents a menu.
6. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
7. Select "Upgrade ATF BL2", then use this file:
openwrt-mediatek-filogic-qihoo_360t7-preloader.bin
8. Select "Upgrade ATF FIP", then use this file:
openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip
9. Download the initramfs image, and type "reset",
waiting for tftp recovery to complete.
a. After openwrt boots up, perform sysupgrade.
Note:
1. Since NMBM is disabled, we must back up all partitions.
2. Flash instructions is based on commit 28df7f7.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit dc2d4d7393)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rename previous uboot build to mt7986-*.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit c620409d58)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add reserved memory for pstore/ramoops to device tree used by Linux
as well as U-Boot.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3eb354f999)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Pick accepted patches from upstream Linux tree instead of having to
maintain our slightly different downstream patches.
Import pending patch fixing I2C on MT7981 by making sure all clocks
are enabled before accessing I2C registers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 213b728276)
Add kernel tags to the patches that got accepted upstream.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 2388b119de)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure sub-images on the SD card are size-checked, allow
generating SD card without squashfs and/or initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 43d27b0252)
CONFIG_PAHOLE_HAS_SPLIT_BTF should be runtime detected as it depends on
pahole being available on the host, so filter it out of configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3591353f51)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This add basic device tree support for mediatek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit e3a681bab4)
Backport cpufreq changes from upstream so that the MediaTek MT7988 SoC
can be supported.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit e4555d69a1)
The Richtek RT5190A is used on the MT7988 reference board. Backport and
enable the driver on the filogic subtarget, so we can support cpufreq
on the MT7988 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit a3cf3e2c48)
Add driver for the built-in 2.5G Ethernet PHY found in the MT7988 SoC.
To function the PHY also needs firmware files which have not yet been
published via linux-firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ef2a831dab)
Update driver for MediaTek's built-in Gigabit Ethernet PHYs which can be
found in the MT7981 and MT7988 SoCs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 987a0b2b30)
Backport commits adding support for the MT7988 built-in switch to the
mt7530 driver.
This change results in the Kconfig symbol NET_DSA_MT7530 to be extended
by NET_DSA_MT7530_MDIO (everything formally covered by NET_DSA_MT7530)
and NET_DSA_MT7530_MMIO (a new driver for the MMIO-connected built-in
switch of the MT7988 SoC).
Select NET_DSA_MT7530_MDIO for all targets previously selecting
NET_DSA_MT7530, with the exception of mediatek/filogic which also
selects NET_DSA_MT7530_MMIO.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 958fdf36e3)
In order to support Ethernet on the MT7988 SoC add support for NETSYS v3
as well as new paths and USXGMII SerDes to the mtk_eth_soc driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 6983a215d9)
This adds provisional pinctrl driver support for the MediaTek MT7988 SoC.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9e6a7e808f)
This adds clock drivers for the MediaTek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit b33c185876)
Setup all necessary clocks to get MMC to work on MT7981, similar to
how it is done also on MT7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit a9989b30d0)
There is no reason to limit USB to 2.0 mode
by default, delete this limit.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit b2beb4c688)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows loading modules with large memory requirements, recently needed
while testing on armvirt/32. Past forum discussions [1] and bug reports [2]
also raised this and the ipq806x target already set it in response [3].
Given this increases kernel image size by only ~1KB, is generally useful on
multi-platform kernels, and enabled by default on upstream arm32 Linux, add
it to the generic config.
The setting has similar utility on arm64, is a requirement for KASLR, and
already enabled on most OpenWrt aarch64 targets, so pull this into the
top-level generic config.
[1]: https://forum.openwrt.org/t/vmap-allocation-for-size-442368-failed-use-vmalloc-size-to-increase-size/34545/7
[2]: https://github.com/openwrt/openwrt/issues/8282
[3]: f81e148eb6 ("ipq806x: update 4.19 kernel config").
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit c2d194a34e)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow building SD card images without having both initramfs and squashfs
present on the card, just like it has already been done for the mt7622
and filogic subtargets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d6fef27f2d)
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
(cherry picked from commit 1c05388ab0)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 0ffbef9317)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit e5d8739aa8)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch enables NVMEM u-boot-env driver (COFNIG_NVMEM_U_BOOT_ENV) on
generic subtarget to use from devices, for MAC address and etc.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit e8f7957450)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
the UML build fails during the kernel build:
| arch/um/drivers/net_kern.c: In function 'compute_hash':
| arch/um/drivers/net_kern.c:322:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
| 322 | }
| | ^
|cc1: all warnings being treated as errors
The compute_hash() function is added by our patch:
102-pseudo-random-mac.patch
Instead of allocating a 1024 byte buffer on the stack for the SHA1
digest input, let's allocate the data on the heap. We should be
able to do that since crypto_alloc_ahash and ahash_request_alloc
also need to allocate structures on the heap.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit aed2569d37)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The PHY name has been changed to "mt7530-0" since IRQ support
was added to MT7530 driver.
Fixes: f9cfe7af1f ("kernel: backport MT7530 IRQ support")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(node names, added color, function+function-enumerator properties)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Sophos SG/XG-135 revision 3 has odd numbering of eth ports
where the WAN port (as marked on the case) is:
`eth6` and `eth0`, `eth1`, `eth2`, `eth3`, `eth5`, `eth7`, `eth8` are LAN ports.
Port `eth4` seems to be the SFP port.
Also add the missing LED definition for supported Sophos devices.
Original discussion at:
https://forum.openwrt.org/t/openwrt-on-revision-3-of-sophos-desktop-appliances/152912
Signed-off-by: Stan Grishin <stangri@melmac.ca>
Iomega Storcenter ix4-200d is a four-bay SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1.2GHz. It has 512MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 2x 1Gbit/s NIC
Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1200Mhz
- Flash size: 32 MiB
- RAM: 512MB
- LAN: 2x 1Gbit/s
- 3x USB 2.0
Notes:
- The blue drive LED is triggered by HDD activity, it can not be controlled
via GPIO.
- The LCD screen requires proprietary code and does not function at this time.
- Due to a kernel-related issue with the Marvell 88SE6121 SATA controller,
currently only trays numbered #3 and #4 work, #1 and #2 do not. [1]
Serial pinout:
CN4
--------------
| 10 8 6 4 2 |
| 9 7 5 3 1 |
-------------- PIN 1 Mark (fat line)
1 = RXD
4 = TXD
6 = GND
9 = 3.3V (not necessary to connect)
Installation instructions:
1. download initramfs-uImage and copy into tftp server
2. connect the tftp server to network port #1
3. access uboot environment with serial cable and run
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x00800000 [initramfs-uImage filename]
bootm 0x00800000
4. connect to LAN on network port #2, log into openwrt and sysupgrade to install into flash
[1] https://bugzilla.kernel.org/show_bug.cgi?id=216094
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
(aligned FROM from signed-off. LED+key rename, whitespace removal)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This removes unneeded kernel version switches from the targets after
kernel 5.10 has been dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Recently, a strange variant of ZTE MF286 was discovered, having QCA9886
radio instead of QCA9882 - like MF286A, but having MF286 flash layout
and rest of hardware.
To support both variants in one image, bind calibration data at offset
0x5000 both as "calibration" and "pre-calibration" nvmem-cells, so
ath10k can load caldata for both at runtime.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Specifications
The D-Link EXO AC1750 (DIR-869) router released in 2016.
It is powered by Qualcomm Atheros QCA9563 @ 750 MHz chipset, 64 MB RAM and 16 MB flash.
10/100/1000 Gigabit Ethernet WAN port
Four 10/100/1000 Gigabit Ethernet LAN ports
Power Button, Reset Button, WPS Button, Mode Switch
Flashing
1. Upload factory.bin via D-link web interface (Management/Upgrade).
Revert to stock
Upload original firmware via OpenWrt sysupgrade interface.
Debricking
D-Link Recovery GUI (192.168.0.1)
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
For D-link DIR-859 and DIR-869
Replace the mtd-cal-data by an nvmem-cell.
Add the PCIe node for the ath10k radio to the devicetree.
Thanks to DragonBlue for this patch
Signed-off-by: Jan Forman <jforman@tuta.io>
gpio-export for the switch reset pin replaced with a reset pin definition for the driver, within the phy node.
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
Tested-By: Sebastian Schaper <openwrt@sebastianschaper.net>
The 'KERNEL' is not referenced by other objects, so double '$$' will
cause shell unable to parse the variable 'BLOCKSIZE':
dd ... bs=$(BLOCKSIZE) conv=sync
bash: line 1: BLOCKSIZE: command not found
Fixes: 09a0efbe83(ramips: set default BLOCKSIZE to 64k for nor flash devices)
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Replace the fall through comment with fallthrough; in the ar2315 flash
driver.
This fixes a compile warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of defining an own virt_to_phys() use the version from the
generic MIPS arch code which does the same.
This fixes a compile warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use same logic as in append-metadata so build doesn't fail in case of
missing build-key (it was previously failing on the buildbot runners).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel 5.15.111 includes backport of commit
("firmware: qcom_scm: Clear download bit during reboot") which is causing
reboot on ipq40xx to stop working, more precisely the board will hang after
reboot is called with:
root@OpenWrt:/# reboot
root@OpenWrt:/# [ 76.473541] device lan1 left promiscuous mode
[ 76.474204] br-lan: port 1(lan1) entered disabled state
[ 76.527975] device lan2 left promiscuous mode
[ 76.530301] br-lan: port 2(lan2) entered disabled state
[ 76.579376] device lan3 left promiscuous mode
[ 76.581698] br-lan: port 3(lan3) entered disabled state
[ 76.638434] device lan4 left promiscuous mode
[ 76.638777] br-lan: port 4(lan4) entered disabled state
[ 76.978489] qca8k-ipq4019 c000000.switch wan: Link is Down
[ 76.978883] device eth0 left promiscuous mode
[ 76.987077] ipqess-edma c080000.ethernet eth0: Link is Down
[
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00123
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1339 - bootable_media_detect_entry, Start
B - 1679 - bootable_media_detect_success, Start
B - 1693 - elf_loader_entry, Start
B - 5076 - auth_hash_seg_entry, Start
B - 7223 - auth_hash_seg_exit, Start
B - 578349 - elf_segs_hash_verify_entry, Start
B - 696356 - PBL, End
B - 696380 - SBL1, Start
B - 787236 - pm_device_init, Start
D - 7 - pm_device_init, Delta
B - 788701 - boot_flash_init, Start
D - 52782 - boot_flash_init, Delta
B - 845625 - boot_config_data_table_init, Start
D - 3836 - boot_config_data_table_init, Delta - (419 Bytes)
B - 852841 - clock_init, Start
D - 7566 - clock_init, Delta
B - 864883 - CDT version:2,Platform ID:9,Major ID:0,Minor ID:0,Subtype:64
B - 868413 - sbl1_ddr_set_params, Start
B - 873402 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 877842 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13234 - sbl1_ddr_set_params, Delta
B - 891155 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 909105 - Image Load, Start
B - 1030210 - Boot error ocuured!. Error code: 303d
So, until a proper fix is found, lets revert the culprit patch to have
reboot working again.
Fixes: 228e0e1039 ("kernel: bump 5.15 to 5.15.111")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Manually adjusted before running quilt due to new location in tree:
backport-5.15/780-v5.16-bus-mhi-pci_generic-Introduce-Sierra-EM919X-support.patch
backport-5.15/781-v6.1-bus-mhi-host-always-print-detected-modem-name.patch
pending-5.15/790-bus-mhi-core-add-SBL-state-callback.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
The NanoPi R2C is a minor variant of NanoPi R2S with the on-board NIC
chip changed from rtl8211e to yt8521s, and otherwise identical to R2S.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The bootscript for nanopi r2s/r4s only changes the serial address, so
make it auto detected in mmc bootscript rather than creating more
(redudant) files.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
should have been part of the ipq-wifi update.
Fixes: 8217f02a1c ("ipq-wifi: drop upstreamed board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add a ventana-img.gz compressed disk image to support
squashfs+ext4 on a block storage device such as USB/MMC/SATA.
The Ventana bootloader expects the bootscript to be
boot/6x_bootscript-ventana therefore we must create a bootfs
that matches this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
These same codes are repeated for many devices now, it's better to
move them to shared definition. This commit also add the missing
KERNEL_SIZE of the ZyXEL NR7101 and ZyXEL LTE3301-PLUS.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In kernel 5.15, the default erase sector size of the nor flash has
been switched from 4k to 64k. This may cause the configuration not
be preserved across upgrades. To avoid this issue, change the default
BLOCKSIZE to 64k.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Make use of minor sector size (4k) on supported flash chips to improve
spi read/write performance.
Tested on ramips/mt7628: Motorola MWR03
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The BDFs for the:
Aruba AP-365
Devolo Magic 2 WiFi next
Edgecore ECW5410
Edgecore OAP100
Extreme Networks WS-AP3915i
GL.iNet GL-A1300
GL.iNet GL-AP1300
GL.iNet GL-S1300
Linksys EA8300
Linksys WHW03v2
Nokia Wi4A AC400i
P&W R619AC
Pakedge WR-1
Qxwlan E2600AC C1
Sony NCP-HG100/Cellular
Teltonika RUTX10
ZTE MF18A
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git.
Furthermore the BDFs for the:
8devices Habanero
8devices Jalapeno
Qxwlan E2600AC C2
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use <mdio>:<addr>:<speed> trigger instead of netdev(link) trigger for
Fortinet FortiGate 50E, to indicate link speed on the each phys.
1000 Mbps: Green
100 Mbps : Amber
10 Mbps : (turn off)
Fixes: 102dc5a625 ("mvebu: add support for Fortinet FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use <mdio>:<addr>:<speed> trigger for LEDs, enable PHY LED trigger
(CONFIG_LED_TRIGGER_PHY).
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Enable BLK_DEV_SD and USB_STORAGE so that rootfs can be on a USB Mass
Storage device.
This increases the kernel Image by 66KiB
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable BLK_DEV_SD and USB_STORAGE so that rootfs can be on a USB Mass
Storage device.
This adds 23KiB to the compressed kernel size
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
support for MR18 and MR26 was developped before
the userspace nu801 was integrated with x86's
MX100 into OpenWrt. The initial nu801 + kmod-leds-uleds
caused build-bot errors.
The solution that worked for the MX100 was to include
the kmod-leds-uleds to the device platform module.
Thankfully, the MR26 and MR18 can just add the uleds
package to the DEVICE_PACKAGES variable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Rename Newifi D2 to D-Team Newifi D2, and Newifi D1 to Lenovo Newifi D1.
Let's not make naming exceptions because of marketing whims.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a
TOZED TL70-C cellular modem which supports the NCM mode.
The stock firmware does SIM locking on the modem by stopping dialing when a
different PLMN is detected. This is not the case on OpenWrt.
Specifications:
- CPU: MediaTek MT7621AT
- RAM: 256MB DDR3
- NOR Flash: MX25L12833FM2I 16MB SPI Flash
- Wi-Fi 2.4Ghz: MT7603E
- Wi-Fi 5Ghz: MT7612E
- Switch: MT7530 4x 1Gbit Ports
- WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem
- USB: 1x optional USB2.0 external port
- Switches/Buttons: WPS, Reset, Power Switch
- LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone
Installation and TFTP Recovery:
- Connect to serial console.
- Boot initramfs image by choosing option 1 when U-Boot prompts.
- Install sysupgrade image via OpenWrt.
Serial Pins:
Located at the bottom right when looking from the front, right under the
Reset/WPS buttons. The pinout from the left is:
- RX
- GND
- TX
Baudrate is 115200.
When connecting from a powered off state, disconnect RX as it blocks the
boot process.
Link: http://www.sztozed.com/en/contents/58/84.html
Co-developed-by: Andre Cruz <me@1conan.com>
Signed-off-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
When adding support for the GL.iNet GL-MT3000 a reference to the
non-existent make_gl_metadata.py script was accidentally added.
Remove it, flashing from vendor firmware also works fine without that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
16MB SPI-NOR (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
[LEDS] VCC-GND-RX-TX [ETH]
Header is located below the heatsink
Case
----
Unscrew the 4 bottom screws. Remove the top of the case by inserting a
small screwdriver into the ventilation holes and lift the top cover.
This works best by beginning near the ETH-ports. The top is clipped on
the front near the LEDs with two plastic clips. The back has a single
clip in the middle. Start at one of the back edges.
MAC-Addresses
-------------
80:AF:CA:00:F9:C6 LAN
80:AF:CA:00:F9:C7 WAN
80:AF:CA:00:F9:C6 W2
82:AF:CA:30:F9:C6 W5
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device. Keep pressing the "0" key to enter the U-Boot
shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.2. Rename the image to "cudy3000.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Note: Cudy does not yet provide a image for disabling their
signature-protection. This has happened in the past. Make sure to check
the wiki for a possible easier installation method.
Signed-off-by: David Bauer <mail@david-bauer.net>
Import patch to prevent crashes in case WO firmware is missing on devices
with only a single frontend (eg. MT7981+MT7976).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Following 5264296, Mirotik NAND devices now use yafut to flash the
kernel on devices. This method is incompatible with the old-style
"kernel2minor" flash mechanism.
Even though NAND images were disabled in default build since 21.02, a
user flashing a new-style image onto an old-style image would result in
in a soft-brick[1]. In order to prevent such accidental mishap,
especially as these device images will be reenabled in the upcoming
release, bump the compat version.
After the new image is flashed, the compat version can be updated:
uci set system.@system[0].compat_version='1.1'
uci commit
[1] https://github.com/openwrt/openwrt/pull/12225#issuecomment-1517529262
Cc: Michał Kępień <openwrt@kempniu.pl>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Refresh patches to make them cleanly apply.
This problem was found by the github CI.
Fixes: ecd9abc8c0 ("kernel: use upstream firmware patch for Broadcom's NVRAM")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It has just been queued for the v6.5. It allows Ethernet drivers to read
MACs from NVRAM using NVMEM interface.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The following adds the Aerohive BR200-WP router to OpenWrt under
the mpc85xx/p1010 subtarget.
Hardware:
- SoC: Freescale P1011
- NOR: Intel JS28F512M29EWH 64MB
- Memory: 2x Nanya NT5TU64M16GG-AC 128MB (Total of 256MB)
- 2.4GHz WiFi: Atheros AR9390-AL1A
- Eth1: Atheros AR8035-A PoE
- 2x LEDs
- 1x Button
- PoE PSE
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a
password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, tftp boot the initramfs image:
dhcp; setenv serverip 192.168.1.3;
tftpboot 0x2004000 openwrt-mpc85xx-p1010-aerohive_br200-wp-initramfs-kernel.bin;
bootm 0x2004000;
3. Once booted, scp over the sysupgrade file and sysupgrade the device
to flash LEDE to the NOR.
Note:
MAC assigns are taken from stock firmware:
Name MAC addr Mode State Chan(Width) VLAN Radio Hive SSID
-------- -------------- -------- ----- ----------- ---- ---------- ---------- ---------
Mgt0 08ea:44XX:XXc0 - U - 1 - hive0 -
Eth0 08ea:44XX:XXc0 wan U - - - - -
Eth1 08ea:44XX:XXc2 access D - - - hive0 -
Eth2 08ea:44XX:XXc3 access D - - - hive0 -
Eth3 08ea:44XX:XXc4 access D - - - hive0 -
Eth4 08ea:44XX:XXc5 access D - - - hive0 -
Wifi0 08ea:44XX:XXd0 access U 1(20MHz) - radio_ng0 - -
Wifi0.1 08ea:44XX:XXd4 access D 1(20MHz) - radio_ng0 hive0 -
Note2:
PoE PSE could be managed with `realtek-poe` package. Example port
config:
config port
option enable '1'
option id '4'
option name 'lan2'
option poe_plus '0'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan1'
option poe_plus '0'
option priority '1'
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(switch@0 -> switch@10, Device's quickstart says LEDs are
amber and white => add function+color properties but keep
labels around, use pr_info)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
DTSes from of three boards was sent and accpeted upstream. Let's use
backport patches with small OpenWrt tweak like other upstream stuff.
List of boards:
- Zyxel NSA310S
- Endian 4i Edge 200
- Ctera C-200 V1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Specifications:
SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz
RAM: 2x Winbond W9751G6KB-25 (128 MiB)
FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB)
WIFI1: Atheros AR9550 5.0GHz (SoC)
WIFI2: Atheros AR9582-AR1A 2.4GHz
WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz
PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN)
LED: 1x Power-LED, 1 x RGB Tricolor-LED
INPUT: One Reset Button
UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8
(VCC, RX, TX, GND - VCC is closest to the boot set jumper
under the console pins.)
Flashing instructions:
Depending on the installed firmware, there are vastly different
methods to flash a MR18. These have been documented on:
<https://openwrt.org/toh/meraki/mr18>
Tip:
Use an initramfs from a previous release and then use sysupgrade
to get to the later releases. This is because the initramfs can
no longer be built by the build-bots due to its size (>8 MiB).
Note on that:
Upgrades from AR71XX releases are possible, but they will
require the force sysupgrade option ( -F ).
Please backup your MR18's configuration before starting the
update. The reason here is that a lot of development happend
since AR71XX got removed, so I do advise to use the ( -n )
option for sysupgrade as well. This will cause the device
to drop the old AR71xx configuration and make a new
configurations from scratch.
Note on LEDs:
The LEDs has changed since AR71XX. The white LED is now used during
the boot and when upgrading instead of the green tricolor LED. The
technical reason is that currently the RGB-LED is brought up later
by a userspace daemon.
(added warning note about odm-caldata partition. remove initramfs -
it's too big to be built by the bots. MerakiNAND -> meraki-header.
sort nu801's targets)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This sort of reverts Koen Vandeputte's commit
6561ca1fa5 ("ath79: ar934x: fix mounting issues if subpage is not supported")
since it does not work on the MR18 as the UBI is coming from
Meraki in that way and it used to work with AR71XX before.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Two Mikrotik board families (SXT 5nD R2 and Routerboard 92x are using
software ECC on NAND. Some of them use chips capable of subpage write,
others do not - within the same family, and a common block size is
required for UBI, to avoid mounting errors. Set the ECC step size
explicitly for them to 2048B, so UBI can mount existing volumes without
problems, at the same time allowing to unlocking subpage write functionality,
reuqired for Meraki MR18.
Fixes: 6561ca1fa5 ("ath79: ar934x: fix mounting issues if subpage is not supported")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
specify that this functions adds a Cisco Meraki
special-sauce header for their custom loader/uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
We only use 5.15 kernel. So remove all those unnecessary symbols
referencing 5.10 or 5.15 kernel.
Can be found with:
git grep -E 'LINUX_5_1(0|5)'
Note that we remove the dependency from "sound-soc-chipdip-dac" instead
of removing the complete kernel package. The 5.15 version bump forgot to
delete the "@LINUX_5_10" dependency. The kernel package is still needed
in 5.15 kernel.
Signed-off-by: Nick Hainke <vincent@systemli.org>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to kernel 5.15 although it is marked as source only. It is marked
as source only because nobody was able to test this device.
Merging this is important to finally branch a new release. We want to
get rid completely of 5.10 kernel. Without this commit we get following
error: "Missing kernel version/hash file for 5.10." Hopfully someone
will fix the board in the rc phase or it will be removed completly.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Manually refreshed:
- 140-redboot_boardconfig.patch
- 141-redboot_partition_scan.patch
- 142-redboot_various_erase_size_fix.patch
Automatically refreshed:
- 107-ar5312_gpio.patch
- 108-ar2315_gpio.patch
- 110-ar2313_ethernet.patch
- 120-spiflash.patch
- 130-watchdog.patch
- 330-board_leds.patch
Use "make kernel_oldconfig" to refresh the new kernel config.
The Ubiquiti Nanostation 2 (XS2) and Ubiquiti Nanostation 5 (XS5) should
be marked as broken when switching to 5.15 by default. The new kernel
does not fit anymore into the partition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to kernel 5.15 although it is marked as source only. It is marked
as source only because the eth0 interface can't be added to the br-lan
default interface resulting in a broken ethernet [0]. There is a
workaround to set a higher pvd (e.g. to 4000) in the dts [1].
Other functionality was already tested on a Beaglebone Black for
+6month now without issues.
Merging this is important to finally branch a new release. We want to
get rid completely of 5.10 kernel. Without this commit we get following
error: "Missing kernel version/hash file for 5.10." Hopfully someone
will fix the board in the rc phase.
- [0] https://github.com/openwrt/openwrt/issues/11953
- [1] https://github.com/openwrt/openwrt/issues/11953#issuecomment-1419078990
Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
[rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
pcibios_map_irq request a const pci_dev while pci_find_capability
doesn't. Cast dropping the const to fix compilation warning.
Fix compilation warning:
arch/mips/pci/fixup-lantiq.c: In function 'pcibios_map_irq':
arch/mips/pci/fixup-lantiq.c:34:33: error: passing argument 1 of 'pci_find_capability' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
34 | if (pci_find_capability(dev, PCI_CAP_ID_EXP))
| ^~~
In file included from arch/mips/pci/fixup-lantiq.c:9:
./include/linux/pci.h:1129:40: note: expected 'struct pci_dev *' but argument is of type 'const struct pci_dev *'
1129 | u8 pci_find_capability(struct pci_dev *dev, int cap);
| ~~~~~~~~~~~~~~~~^~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch does not have a valid patch headers and does not apply on
an external git tree with 'git am'. To fix this add the missing header.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The OF LED configuration patch fails on MT7621, as the necessary headers
were only included for the mediatek subtarget with an additional patch.
Fixes: 242fe8634e ("generic: add hack for MT753x LED configuration")
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix compilation warning for dev_err in rb91x_nand driver.
Fix compilation warning:
drivers/mtd/nand/raw/rb91x_nand.c:289:25: note: in expansion of macro 'dev_err'
289 | dev_err(dev, "failed to get gpios: %d\n",
| ^~~~~~~
drivers/mtd/nand/raw/rb91x_nand.c:289:61: note: format string is defined here
289 | dev_err(dev, "failed to get gpios: %d\n",
| ~^
| |
| int
| %ld
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Comment unused function macronix_nand_block_protection_support since it
does cause boot problem
Fix compilation error:
drivers/mtd/nand/raw/nand_macronix.c:220:13: error: 'macronix_nand_block_protection_support' defined but not used [-Werror=unused-function]
220 | static void macronix_nand_block_protection_support(struct nand_chip *chip)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Comment unused macronix_nand_block_protection_support due to workaround
needed to fix booting
Fix compilation warning:
drivers/mtd/nand/raw/nand_macronix.c:220:13: error: 'macronix_nand_block_protection_support' defined but not used [-Werror=unused-function]
220 | static void macronix_nand_block_protection_support(struct nand_chip *chip)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for using %d instead of %ld for gpio-latch in
dev_err.
Fix compilation warning:
In file included from ./include/linux/device.h:15,
from ./include/linux/gpio/driver.h:5,
from drivers/gpio/gpio-latch.c:13:
drivers/gpio/gpio-latch.c: In function 'gpio_latch_probe':
drivers/gpio/gpio-latch.c:137:46: error: format '%d' expects argument of type 'int', but argument 4 has type 'long int' [-Werror=format=]
137 | dev_err(dev, "failed to get gpio %d: %d\n", i,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
drivers/gpio/gpio-latch.c:137:33: note: in expansion of macro 'dev_err'
137 | dev_err(dev, "failed to get gpio %d: %d\n", i,
| ^~~~~~~
drivers/gpio/gpio-latch.c:137:71: note: format string is defined here
137 | dev_err(dev, "failed to get gpio %d: %d\n", i,
| ~^
| |
| int
| %ld
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch commenting unused sdhci function, hopin this will be dropped
when the problem is actually found.
Fix compilation warning:
drivers/mmc/host/sdhci-msm.c:1781:13: error: 'sdhci_msm_set_clock' defined but not used [-Werror=unused-function]
1781 | static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
| ^~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework some desc dump and dummy pkt function to fix compilation warning.
Fix compilation warning:
drivers/staging/fsl_ppfe/pfe_hif.c: In function 'send_dummy_pkt_to_hif':
drivers/staging/fsl_ppfe/pfe_hif.c:118:19: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
118 | ddr_ptr = (void *)((u64)readl(BMU2_BASE_ADDR + BMU_ALLOC_CTRL));
| ^
drivers/staging/fsl_ppfe/pfe_hif.c:122:20: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
122 | lmem_ptr = (void *)((u64)readl(BMU1_BASE_ADDR + BMU_ALLOC_CTRL));
| ^
drivers/staging/fsl_ppfe/pfe_hif.c: In function 'pfe_hif_desc_dump':
drivers/staging/fsl_ppfe/pfe_hif.c:195:24: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
195 | desc_p = (u32)((u64)desc - (u64)hif->descr_baseaddr_v +
| ^
drivers/staging/fsl_ppfe/pfe_hif.c:195:36: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
195 | desc_p = (u32)((u64)desc - (u64)hif->descr_baseaddr_v +
| ^
drivers/staging/fsl_ppfe/pfe_hif.c:207:19: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
207 | desc_p = ((u64)desc - (u64)hif->descr_baseaddr_v +
| ^
drivers/staging/fsl_ppfe/pfe_hif.c:207:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
207 | desc_p = ((u64)desc - (u64)hif->descr_baseaddr_v +
| ^
cc1: all warnings being treated as errors
In file included from ./include/linux/kernel.h:19,
from ./include/linux/list.h:9,
from ./include/linux/wait.h:7,
from ./include/linux/eventfd.h:13,
from drivers/staging/fsl_ppfe/pfe_cdev.c:11:
drivers/staging/fsl_ppfe/pfe_cdev.c: In function 'pfe_cdev_read':
./include/linux/kern_levels.h:5:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'int' [-Werror=format=]
5 | #define KERN_SOH "\001" /* ASCII Start Of Header */
| ^~~~~~
./include/linux/printk.h:422:25: note: in definition of macro 'printk_index_wrap'
422 | _p_func(_fmt, ##__VA_ARGS__); \
| ^~~~
./include/linux/printk.h:132:17: note: in expansion of macro 'printk'
132 | printk(fmt, ##__VA_ARGS__); \
| ^~~~~~
./include/linux/printk.h:580:9: note: in expansion of macro 'no_printk'
580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~~
./include/linux/kern_levels.h:15:25: note: in expansion of macro 'KERN_SOH'
15 | #define KERN_DEBUG KERN_SOH "7" /* debug-level messages */
| ^~~~~~~~
./include/linux/printk.h:580:19: note: in expansion of macro 'KERN_DEBUG'
580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~~~
drivers/staging/fsl_ppfe/pfe_cdev.c:42:17: note: in expansion of macro 'pr_debug'
42 | pr_debug("%u %lu", link_states[ret].phy_id,
| ^~~~~~~~
./include/linux/kern_levels.h:5:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'size_t' {aka 'unsigned int'} [-Werror=format=]
5 | #define KERN_SOH "\001" /* ASCII Start Of Header */
| ^~~~~~
./include/linux/printk.h:422:25: note: in definition of macro 'printk_index_wrap'
422 | _p_func(_fmt, ##__VA_ARGS__); \
| ^~~~
./include/linux/printk.h:493:9: note: in expansion of macro 'printk'
493 | printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~
./include/linux/kern_levels.h:11:25: note: in expansion of macro 'KERN_SOH'
11 | #define KERN_ERR KERN_SOH "3" /* error conditions */
| ^~~~~~~~
./include/linux/printk.h:493:16: note: in expansion of macro 'KERN_ERR'
493 | printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~
drivers/staging/fsl_ppfe/pfe_cdev.c:50:17: note: in expansion of macro 'pr_err'
50 | pr_err("Failed to send (%d)bytes of (%lu) requested.\n",
| ^~~~~~
./include/linux/kern_levels.h:5:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 2 has type 'unsigned int' [-Werror=format=]
5 | #define KERN_SOH "\001" /* ASCII Start Of Header */
| ^~~~~~
./include/linux/printk.h:422:25: note: in definition of macro 'printk_index_wrap'
422 | _p_func(_fmt, ##__VA_ARGS__); \
| ^~~~
./include/linux/printk.h:132:17: note: in expansion of macro 'printk'
132 | printk(fmt, ##__VA_ARGS__); \
| ^~~~~~
./include/linux/printk.h:580:9: note: in expansion of macro 'no_printk'
580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~~
./include/linux/kern_levels.h:15:25: note: in expansion of macro 'KERN_SOH'
15 | #define KERN_DEBUG KERN_SOH "7" /* debug-level messages */
| ^~~~~~~~
./include/linux/printk.h:580:19: note: in expansion of macro 'KERN_DEBUG'
580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~~~
drivers/staging/fsl_ppfe/pfe_cdev.c:57:9: note: in expansion of macro 'pr_debug'
57 | pr_debug("Read of (%lu) bytes performed.\n", sizeof(link_states));
| ^~~~~~~~
cc1: all warnings being treated as errors
In file included from ./include/uapi/linux/posix_types.h:5,
from ./include/uapi/linux/types.h:14,
from ./include/linux/types.h:6,
from ./include/linux/list.h:5,
from ./include/linux/module.h:12,
from drivers/staging/fsl_ppfe/pfe_sysfs.c:7:
drivers/staging/fsl_ppfe/pfe_sysfs.c: In function 'pfe_set_util':
./include/linux/stddef.h:8:14: error: passing argument 2 of 'kstrtoul' makes integer from pointer without a cast [-Werror=int-conversion]
8 | #define NULL ((void *)0)
| ^~~~~~~~~~~
| |
| void *
drivers/staging/fsl_ppfe/pfe_sysfs.c:538:39: note: in expansion of macro 'NULL'
538 | util_do_clear = kstrtoul(buf, NULL, 0);
| ^~~~
In file included from ./include/linux/kernel.h:13,
from ./include/linux/list.h:9:
./include/linux/kstrtox.h:30:69: note: expected 'unsigned int' but argument is of type 'void *'
30 | static inline int __must_check kstrtoul(const char *s, unsigned int base, unsigned long *res)
| ~~~~~~~~~~~~~^~~~
cc1: all warnings being treated as errors
With UTIL compiled on, fix compilation warning:
drivers/staging/fsl_ppfe/pfe_hal.c: In function 'pe_load_ddr_section':
drivers/staging/fsl_ppfe/pfe_hal.c:617:19: error: 'else' without a previous 'if'
617 | } else {
| ^~~~
drivers/staging/fsl_ppfe/pfe_hal.c:622:17: error: break statement not within loop or switch
622 | break;
| ^~~~~
drivers/staging/fsl_ppfe/pfe_hal.c:624:9: error: case label not within a switch statement
624 | case SHT_NOBITS:
| ^~~~
drivers/staging/fsl_ppfe/pfe_hal.c:627:17: error: break statement not within loop or switch
627 | break;
| ^~~~~
drivers/staging/fsl_ppfe/pfe_hal.c:629:9: error: 'default' label not within a switch statement
629 | default:
| ^~~~~~~
drivers/staging/fsl_ppfe/pfe_hal.c: At top level:
drivers/staging/fsl_ppfe/pfe_hal.c:635:9: error: expected identifier or '(' before 'return'
635 | return 0;
| ^~~~~~
drivers/staging/fsl_ppfe/pfe_hal.c:636:1: error: expected identifier or '(' before '}' token
636 | }
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for PHY_INTERFACE_MODE_2500SGMII patch.
Fix compilation warning:
drivers/net/phy/phylink.c: In function 'phylink_get_linkmodes':
drivers/net/phy/phylink.c:360:9: error: enumeration value 'PHY_INTERFACE_MODE_2500SGMII' not handled in switch [-Werror=switch]
360 | switch (interface) {
| ^~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop arm override compile patch. The use is dubious and at times (2016)
it was never explained why this was required.
Krait CPU and Cortex-a15 may be similar but they have some intrinsic
difference. While very similar they differ a lot in additional feature
and also cache configuration.
Also these conflict with raid6 libraty compilation that use specific
workaround not compatible with cortex-a15 and produce compilation
warning.
Fix compilation warning:
cc1: error: switch '-mcpu=cortex-a15' conflicts with switch '-march=armv7-a+simd' [-Werror]
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace fallthrough comment with fallthrough macro for rtl838x ethernet
driver.
Fix compilarion warning:
drivers/net/ethernet/rtl838x_eth.c: In function 'rtl930x_mdio_reset':
drivers/net/ethernet/rtl838x_eth.c:1959:43: error: this statement may fall through [-Werror=implicit-fallthrough=]
1959 | private_poll_mask |= BIT(i);
drivers/net/ethernet/rtl838x_eth.c:1961:17: note: here
1961 | case PHY_INTERFACE_MODE_USXGMII:
| ^~~~
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix uninizialized variable in rtl83xx qos driver
Fix compilation error:
drivers/net/dsa/rtl83xx/qos.c: In function 'rtl838x_setup_prio2queue_matrix':
drivers/net/dsa/rtl83xx/qos.c:298:19: error: 'v' is used uninitialized [-Werror=uninitialized]
298 | v |= i << (min_queues[i] * 3);
| ~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/qos.c:294:13: note: 'v' was declared here
294 | u32 v;
| ^
drivers/net/dsa/rtl83xx/qos.c: In function 'rtl83xx_setup_prio2queue_cpu_matrix':
drivers/net/dsa/rtl83xx/qos.c:320:19: error: 'v' is used uninitialized [-Werror=uninitialized]
320 | v |= max_queues[i] << (i * 3);
| ~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/qos.c:316:13: note: 'v' was declared here
316 | u32 v;
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Comment unused part of realtek phy driver.
Fix compilation warning:
drivers/net/phy/rtl83xx-phy.c: In function 'rtl8380_configure_int_rtl8218b':
drivers/net/phy/rtl83xx-phy.c:747:21: error: unused variable 'ipd_flag' [-Werror=unused-variable]
747 | int ipd_flag = 1;
| ^~~~~~~~
drivers/net/phy/rtl83xx-phy.c: At top level:
drivers/net/phy/rtl83xx-phy.c:3333:13: error: 'rtl931x_sds_disable' defined but not used [-Werror=unused-function]
3333 | static void rtl931x_sds_disable(u32 sds)
| ^~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Comment unused part of realtek dsa driver.
Fix compilation warning:
drivers/net/dsa/rtl83xx/common.c: In function 'rtl83xx_fib_event':
drivers/net/dsa/rtl83xx/common.c:1430:58: error: unused variable 'fen6_info' [-Werror=unused-variable]
1430 | struct fib6_entry_notifier_info *fen6_info = ptr;
| ^~~~~~~~~
drivers/net/dsa/rtl83xx/common.c: At top level:
drivers/net/dsa/rtl83xx/common.c:531:12: error: 'rtl83xx_octet_cntr_alloc' defined but not used [-Werror=unused-function]
531 | static int rtl83xx_octet_cntr_alloc(struct rtl838x_switch_priv *priv)
| ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Drop unused priv in realtek dsa driver.
Fix compilation warning:
drivers/net/dsa/rtl83xx/dsa.c: In function 'rtl83xx_port_lag_change':
drivers/net/dsa/rtl83xx/dsa.c:2016:37: error: unused variable 'priv' [-Werror=unused-variable]
2016 | struct rtl838x_switch_priv *priv = ds->priv;
| ^~~~
cc1: all warnings being treated as errors
Comment rtl838x_pie_rule_dump in realtek dsa driver for rtl83xx
Fix compilation warning:
drivers/net/dsa/rtl83xx/rtl838x.c:1294:13: error: 'rtl838x_pie_rule_dump' defined but not used [-Werror=unused-function]
1294 | static void rtl838x_pie_rule_dump(struct pie_rule *pr)
| ^~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Comment multiple function in realtek dsa driver for rtl930x
Fix compilation warning:
drivers/net/dsa/rtl83xx/rtl930x.c:1463:12: error: 'rtl930x_l3_intf_add' defined but not used [-Werror=unused-function]
1463 | static int rtl930x_l3_intf_add(struct rtl838x_switch_priv *priv, struct rtl838x_l3_intf *intf)
| ^~~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/rtl930x.c:1414:12: error: 'rtl930x_l3_mtu_del' defined but not used [-Werror=unused-function]
1414 | static int rtl930x_l3_mtu_del(struct rtl838x_switch_priv *priv, int mtu)
| ^~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/rtl930x.c:995:12: error: 'rtl930x_l3_hash6' defined but not used [-Werror=unused-function]
995 | static u32 rtl930x_l3_hash6(struct in6_addr *ip6, int algorithm, bool move_dip)
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
drivers/net/dsa/rtl83xx/rtl930x.c:1690:13: error: 'rtl930x_read_pie_fixed_fields' defined but not used [-Werror=unused-function]
1690 | static void rtl930x_read_pie_fixed_fields(u32 r[], struct pie_rule *pr)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/dsa/rtl83xx/rtl930x.c:1432:12: error: 'rtl930x_l3_mtu_add' defined but not used [-Werror=unused-function]
1432 | static int rtl930x_l3_mtu_add(struct rtl838x_switch_priv *priv, int mtu)
| ^~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Comment rtl931x_read_pie_fixed_fields in realtek dsa driver for rtl931x
Fix compilation warning:
drivers/net/dsa/rtl83xx/rtl931x.c:1116:13: error: 'rtl931x_read_pie_fixed_fields' defined but not used [-Werror=unused-function]
1116 | static void rtl931x_read_pie_fixed_fields(u32 r[], struct pie_rule *pr)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Comment rtl93xx_header_vlan_set in realtek ethernet driver for rtl838x
Fix compilation warning:
drivers/net/ethernet/rtl838x_eth.c: At top level:
drivers/net/ethernet/rtl838x_eth.c:164:13: error: 'rtl93xx_header_vlan_set' defined but not used [-Werror=unused-function]
164 | static void rtl93xx_header_vlan_set(struct p_hdr *h, int vlan)
| ^~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework exposing i2c_mii_valid_phy_id and i2c_mii_phy_addr in global
include.
Fix compilation warning:
In file included from drivers/net/phy/sfp.c:11:
./include/linux/mdio/mdio-i2c.h:27:21: error: 'i2c_mii_phy_addr' defined but not used [-Werror=unused-function]
27 | static unsigned int i2c_mii_phy_addr(int phy_id)
| ^~~~~~~~~~~~~~~~
./include/linux/mdio/mdio-i2c.h:22:13: error: 'i2c_mii_valid_phy_id' defined but not used [-Werror=unused-function]
22 | static bool i2c_mii_valid_phy_id(int phy_id)
| ^~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
PHY_INTERFACE_MODE_HSGMII was not handled in phylink_get_linkmodes and
phylink_parse_mode.
Fix compilation warning by adding it in the enum:
drivers/net/phy/phylink.c: In function 'phylink_get_linkmodes':
drivers/net/phy/phylink.c:360:9: error: enumeration value 'PHY_INTERFACE_MODE_HSGMII' not handled in switch [-Werror=switch]
360 | switch (interface) {
| ^~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for hsdma-mt7621:
drivers/staging/mt7621-dma/hsdma-mt7621.c: In function 'mtk_hsdma_probe':
drivers/staging/mt7621-dma/hsdma-mt7621.c:685:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
685 | device_reset(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning from device_reset in fe_probe. On fail print a
warning but don't fail probe.
Fix compilation warning:
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_probe':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1564:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1564 | device_reset(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for debug string in esw driver:
drivers/net/ethernet/ralink/esw_rt3050.c:1535:9: note: in expansion of macro 'dev_info'
1535 | dev_info(&pdev->dev, "mediatek esw at 0x%08lx, irq %d initialized\n",
| ^~~~~~~~
drivers/net/ethernet/ralink/esw_rt3050.c:1535:53: note: format string is defined here
1535 | dev_info(&pdev->dev, "mediatek esw at 0x%08lx, irq %d initialized\n",
| ~~~~^
| |
| long unsigned int
| %08p
cc1: all warnings being treated as errors
Fix unused variable causing compilation warning:
drivers/net/ethernet/ralink/esw_rt3050.c: In function 'esw_interrupt':
drivers/net/ethernet/ralink/esw_rt3050.c:769:13: error: unused variable 'i' [-Werror=unused-variable]
769 | int i;
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move cmd_buf for dbg under ifdef to fix compilation warning:
drivers/mmc/host/mtk-mmc/dbg.c:51:13: error: 'cmd_buf' defined but not used [-Werror=unused-variable]
51 | static char cmd_buf[256];
| ^~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for device_reset in i2s driver.
Fix compilation warning:
sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_probe':
sound/soc/ralink/ralink-i2s.c:885:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
885 | device_reset(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errorralink: mt7620: fix compilation
warning for device_reset in i2s driver
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix mangle bootargs patch compilation warning due to defined but not
used functions.
Fix compilation warning:
arch/arm/boot/compressed/atags_to_fdt.c:63:17: error: 'get_cell_size' defined but not used [-Werror=unused-function]
63 | static uint32_t get_cell_size(const void *fdt)
| ^~~~~~~~~~~~~
arch/arm/boot/compressed/atags_to_fdt.c:43:12: error: 'setprop_cell' defined but not used [-Werror=unused-function]
43 | static int setprop_cell(void *fdt, const char *node_path,
| ^~~~~~~~~~~~
arch/arm/boot/compressed/atags_to_fdt.c:25:12: error: 'setprop' defined but not used [-Werror=unused-function]
25 | static int setprop(void *fdt, const char *node_path, const char *property,
| ^~~~~~~
arch/arm/boot/compressed/atags_to_fdt.c: In function 'atags_to_fdt':
arch/arm/boot/compressed/atags_to_fdt.c:207:18: error: unused variable 'memsize' [-Werror=unused-variable]
207 | int ret, memsize;
| ^~~~~~~
arch/arm/boot/compressed/atags_to_fdt.c:206:13: error: unused variable 'memcount' [-Werror=unused-variable]
206 | int memcount = 0;
| ^~~~~~~~
arch/arm/boot/compressed/atags_to_fdt.c:205:16: error: unused variable 'mem_reg_property' [-Werror=unused-variable]
205 | __be32 mem_reg_property[2 * 2 * NR_BANKS];
| ^~~~~~~~~~~~~~~~
arch/arm/boot/compressed/atags_to_fdt.c: At top level:
arch/arm/boot/compressed/atags_to_fdt.c:174:13: error: 'hex_str' defined but not used [-Werror=unused-function]
174 | static void hex_str(char *out, uint32_t value)
| ^~~~~~~
cc1: all warnings being treated as errors
Also make some variable const to fix compilation warning:
arch/arm/boot/compressed/atags_to_fdt.c: In function 'append_rootblock':
arch/arm/boot/compressed/atags_to_fdt.c:91:13: error: assignment discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
91 | ptr = str - 1;
| ^
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Handle return from device reset in I2C driver. Don't fail on
device_reset error but print a warning.
Fix compilation warning:
sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_probe':
sound/soc/ralink/ralink-i2s.c:885:9: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
885 | device_reset(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Handle return from request_irq in gsw ethernet driver.
Fix compilation warning:
drivers/net/ethernet/ralink/gsw_mt7620.c: In function 'mtk_gsw_init':
drivers/net/ethernet/ralink/gsw_mt7620.c:236:17: error: ignoring return value of 'request_irq' declared with attribute 'warn_unused_result' [-Werror=unused-result]
236 | request_irq(gsw->irq, gsw_interrupt_mt7620, 0,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
237 | "gsw", priv);
| ~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework the patch to completely disable yenta_probe_irq function.
The generated mask is zero by lack due to the fact that probe_irq_mask
use a val never initialized. Correctly rework the ifdef to make the
function always return 0.
Fix compilation warning:
drivers/pcmcia/yenta_socket.c:926:13: error: unused variable 'i' [-Werror=unused-variable]
926 | int i;
| ^
drivers/pcmcia/yenta_socket.c:954:16: error: 'val' is used uninitialized [-Werror=uninitialized]
954 | mask = probe_irq_mask(val) & 0xffff;
| ^~~~~~~~~~~~~~~~~~~
drivers/pcmcia/yenta_socket.c:927:23: note: 'val' was declared here
927 | unsigned long val;
| ^~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit c5cc3d9610 ("lantiq: Change the data-type of mac address in ETOP driver")
changed the type of the mac variable. Since then, the priv->mac check always evaluates
as true, so this check can be removed.
This fix compilation warning:
drivers/net/ethernet/lantiq_etop.c: In function 'ltq_etop_init':
drivers/net/ethernet/lantiq_etop.c:775:13: warning: the comparison will always evaluate as 'true' for the address of 'mac' will never be NULL [-Waddress]
775 | if (priv->mac && !is_valid_ether_addr(mac.sa_data))
| ^~~~
drivers/net/ethernet/lantiq_etop.c:157:23: note: 'mac' declared here
157 | unsigned char mac[6];
|
cc1: all warnings being treated as errors
Fixes: c5cc3d9610 ("lantiq: Change the data-type of mac address in ETOP driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
[ fix wrong fixes tag format ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This fix compilation warning:
printf.c:14:13: warning: type of 'board_putc' does not match original declaration [-Wlto-type-mismatch]
14 | extern void board_putc(int ch);
| ^
board-lantiq.c:24:6: note: type mismatch in parameter 1
24 | void board_putc(char c)
| ^
board-lantiq.c:24:6: note: type 'char' should match type 'int'
board-lantiq.c:24:6: note: 'board_putc' was previously declared here
Fixes: a328b6831c ("lantiq: bring back okli loader")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Drop unused variable in psb6970_config_init. This variable should have
been dropped in 0806f8fc80 ("lantiq: add Linux 5.10 support as testing kernel").
This fix compilation warning:
drivers/net/phy/psb6970.c: In function 'psb6970_config_init':
drivers/net/phy/psb6970.c:310:28: warning: unused variable 'dev' [-Wunused-variable]
310 | struct net_device *dev = pdev->attached_dev;
|
cc1: all warnings being treated as errors
Fixes: 0806f8fc80 ("lantiq: add Linux 5.10 support as testing kernel")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Some write buffer functions are not used when FORCE_WORD_WRITE is set to 1.
So the compile warning messages are output if FORCE_WORD_WRITE is 1. To
resolve this disable the write buffer functions if FORCE_WORD_WRITE is 1.
This fix compilation warning:
drivers/mtd/chips/cfi_cmdset_0001.c:307:13: warning: 'fixup_use_write_buffers' defined but not used [-Wunused-function]
307 | static void fixup_use_write_buffers(struct mtd_info *mtd)
| ^~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Backport patch present upstream fixing error for bcm63xx:
drivers/watchdog/bcm63xx_wdt.c: In function 'bcm63xx_wdt_ioctl':
drivers/watchdog/bcm63xx_wdt.c:208:17: error: this statement may fall through [-Werror=implicit-fallthrough=]
208 | bcm63xx_wdt_pet();
| ^~~~~~~~~~~~~~~~~
drivers/watchdog/bcm63xx_wdt.c:210:9: note: here
210 | case WDIOC_GETTIMEOUT:
| ^~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch fixing binfmt compilation warning on some arch.
This fix compilation warning:
fs/binfmt_elf.c: In function 'parse_elf_properties.isra':
fs/binfmt_elf.c:821:1: error: the frame size of 1040 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
821 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning:
drivers/pinctrl/bcm/pinctrl-bcm4908.c: In function 'bcm4908_pinctrl_probe':
drivers/pinctrl/bcm/pinctrl-bcm4908.c:541:53: error: passing argument 3 of 'pinmux_generic_add_function' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
541 | function->groups,
| ~~~~~~~~^~~~~~~~
In file included from drivers/pinctrl/bcm/pinctrl-bcm4908.c:16:
drivers/pinctrl/bcm/../pinmux.h:153:46: note: expected 'const char **' but argument is of type 'const char * const*'
153 | const char **groups,
| ~~~~~~~~~~~~~^~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Current gcc set a limit for each stack and complain if this limit is not
followed. JFSS2 in build_xattr function currently exceed the limit by
allocating a massive array of struct of 128 elements. Introduce a
pending patch that allocate this temp array dynamically fixing the
compilation warning:
fs/jffs2/xattr.c: In function 'jffs2_build_xattr_subsystem':
fs/jffs2/xattr.c:887:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
887 | }
| ^
Affecting many target that require jffs2 support.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop unused res variable from pci ar724x OF convert patch fixing
compilation warning:
arch/mips/pci/pci-ar724x.c: In function 'ar724x_pci_probe':
arch/mips/pci/pci-ar724x.c:387:26: error: unused variable 'res' [-Werror=unused-variable]
387 | struct resource *res;
| ^~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream commit ("net: phylink: add generic validate implementation") was
backported, however PSGMII PHY mode patch for ipq40xx was not updated to
add PSGMII to phylink_get_linkmodes() so the following warning would be
printed during kernel compilation:
drivers/net/phy/phylink.c: In function 'phylink_get_linkmodes':
drivers/net/phy/phylink.c:360:9: error: enumeration value 'PHY_INTERFACE_MODE_PSGMII' not handled in switch [-Werror=switch]
360 | switch (interface) {
| ^~~~~~
Resolve the warning by adding the PSGMII mode to phylink_get_linkmodes().
Signed-off-by: Robert Marko <robimarko@gmail.com>
Handle error from device reset in SPI ralink driver fixing compilation
warning:
drivers/spi/spi-rt2880.c: In function 'rt2880_spi_probe':
drivers/spi/spi-rt2880.c:474:17: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
474 | device_reset(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop unused res variable from pci ar71xx OF convert patch fixing
compilation warning:
arch/mips/pci/pci-ar71xx.c: In function 'ar71xx_pci_probe':
arch/mips/pci/pci-ar71xx.c:287:26: error: unused variable 'res' [-Werror=unused-variable]
287 | struct resource *res;
| ^~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning from mangle bootargs patch. Now that we flag
warning as error these cause compilation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
From 5.15 and up linux kernel introduced CONFIG_WERROR to flag any
warning as error. To improve code quality, enable this by default to
catch any warning and fix it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 91e3419a33.
Now that squashfs3-lzma generates reproducible output we can drop the
empty binary. Having a binary file in the tree is not nice and we actually
also use squashfs3-lzma for devices which expect the kernel to be loaded
from a squashfs3...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Apply the same LED configuration used by the vendor-firmware for the
GPY211 controlled WAN LED in OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
As we can now configure the switch LED configuration, write the switch
LED configuration values from the vendor firmware to the switch-IC.
Previously, the switch-LEDs did not show any acitvity or link-status
whatsoever.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds a small hack similar to the one used for ar8xxx switches to
read a reg:value map for configuring the LED configuration registers.
This allows OpenWrt to write device-specific LED action as well as blink
configurations. It is unlikely to be accepted upstream, as upstream
plans on integrating their own framework for handling these LEDs.
Signed-off-by: David Bauer <mail@david-bauer.net>
The MT753x switches provide a switch-internal MDIO bus for the embedded
PHYs.
Register a OF sub-node on the switch OF-node for this internal MDIO bus.
This allows to configure the embedded PHYs using device-tree.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix following error when building 32bit arm targets with kmod-crypto-sha512
ERROR: module '/home/user/openwrt/build_dir/target-arm_xscale_musl_eabi/linux-kirkwood_generic/linux-5.15.109/arch/arm/crypto/sha512-arm.ko' is missing.
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
Hardware specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 16 MB (Macronix MX25L12835FM2I-10G)
- RAM: 128 MB (Nanya NT5CC64M16GP-DI)
- WLAN 2.4 GHz: 2x2 MediaTek MT7603EN
- WLAN 5 GHz: 2x2 MediaTek MT7615N
- Ethernet: 1x 10/100/1000 Mbps
- LED: Power, Wifi, WPS
- Button: Reset, WPS
- UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port)
Serial console @ 57600,8n1
Flash instructions:
Connect to serial console and start up the device. As the bootloader got
locked you need to type in a password to unlock U-Boot access.
When you see the following output on the console:
relocate_code Pointer at: 87f1c000
type in the super secure password:
1234567890
Then select TFTP boot from RAM by selecting option 1 in the boot menu.
As Linksys decided to leave out a basic TFTP configuration you need to
set server- & client ip as well as the image filename the device will
search for. You need to use the initramfs openwrt image for the TFTP
boot process.
Once openwrt has booted up, upload the sysupgrade image via scp and run
sysupgrade as normal.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
The previously stated speed of sdr-104 in is too high for the hardware
to reliably communicate with some fast SD cards.
Rockchip boards have a common bug when operating uhs speed, which will
hang the system during a soft reboot.
To be on the safe side, lower the speed to workaround.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
4GB DDR4 RAM
1x 1000 Base-T
2 LEDs (POWER / USER)
HDMI 2.0
3.5mm TRRS AV jack
Micro-SD slot
eMMC slot
1x USB 3.0 Port
2x USB 2.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The filesystem is currently created on every build to trick the boot
loader of some FRITZ! devices into accepting the image. Sadly the
resulting squashfs-lzma filesystem is not reproducible. To fix this,
create a squashfs filesystem once and include it into the repository.
Creation happend as shown below
rm -rf empty_dir
mkdir empty_dir
./staging_dir/host/bin/mksquashfs-lzma \
empty_dir/ empty-squashfs-lzma \
-noappend -root-owned -be -nopad -b 65536 -fixed-time 0
Signed-off-by: Paul Spooren <mail@aparcar.org>
All callers of the rtl83xx_mc_group_* functions already do the same
check, so these aren't needed.
For rtl83xx_mc_group_alloc, this branch also incorrectly returned 0
instead of a negative value. If the branch wasn't effectively dead code
anyway, this could potentially have caused bugs, as 0 is a valid
multicast group entry index.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The current implementation only works when store and load are called for
the same port without any other calls in between. This is because the
store function only saves a single port number instead of a portmask for
each group. It also doesn't take into account that the allocation of
multicast group entries might change between store/load calls.
As a result, the multicast port mask table gets corrupted. This also
includes the reserved entry for unknown multicast, which gets corrupted
even when no other mdb entries have been added.
Remove the code for storing/loading multicast groups entirely, as the
original commit message doesn't offer a convincing reason why this would
be necessary in the first place.
Fixes: 724e4af530 ("realtek: Store and Restore MC memberships for port enable/disable")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
There shouldn't be any reason to forward all multicast to the CPU. The
original commit message also doesn't provide a reason for this seemingly
unrelated change.
The current implementation of the delete method is also broken, as it
entirely removes any entry when the portmask contains only the CPU port,
even if it was explicitly created.
Fixes: 724e4af530 ("realtek: Store and Restore MC memberships for port enable/disable")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
There doesn't appear to be a reason to do this, as only the last entry
is actually reserved for unknown multicast.
This also fixes two issues:
- As the increment happened after the bounds check, the value of the
actually reserved last entry could be overwritten.
- On deletion of entries, a corresponding decrement was missing,
causing the wrong entry to be marked as free.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Actually use the index returned by rtl83xx_find_l2_cam_entry.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The port_vlan_add method may be called while a port is already a member
of that VLAN, so it needs to be able to handle changed flags. Fix it to
properly handle when the PVID or UNTAGGED flag was previously set, but
now no longer is.
To reduce duplication, move PVID configuration to a separate function.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The registers L2_PORT_STATIC_MV_ACT seem to specify the action to take
when the source address of a packet exists as a static fdb entry on
another port. By default the configured action is to drop such packets.
For standalone ports, this behaviour is undesired, as all traffic should
be forwarded to the CPU. So change the action to forward on standalone
ports.
A situation where this issue can occur is when a non-offloaded bond
interface is part of a bridge. In that case, the CPU port will have fdb
entries for devices connected to the bond interface, which are managed
by the assisted learning feature.
For now, this is only implemented for RTL838x/RTL839x, as the available
set of registers differs for the other devices.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
All ports are disabled by default, so configure the port isolation masks
and the pm field accordingly in the setup function. When port_enable is
called for a port, the isolation masks will be set up so that traffic
can flow between the port and the CPU.
While at it, change the code to also use the traffic_set method in
rtl83xx_setup, instead of writing to the RTL838x_PORT_ISO_CTRL(i)
registers directly.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Correctly update the isolation mask of the port being configured. The
port_bitmap variable should contain all other bridge members and needs
to be actually removed from the isolation mask instead of added to it.
Also actually remove the port being configured from the pm field of the
other ports, so that any other ports that are currently disabled will be
configured correctly when they are enabled.
Fixes: df8e6be59a ("rtl838x: add new architecture")
[fixed updating pm field of other ports]
Fixes: 2b88563ee5 ("realtek: update the tree to the latest refactored version")
[reintroduced incorrect pm field update]
Fixes: 27029277f9 ("realtek: add switch driver support for the RTL93XX based switches")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Add support for NXP LS1028ARDB reference board. It's a dual core
Coretex-A53 board with 4G RAM and 5 Eternet ports (4 ports are
connected to MSCC Felix switch).
The original layout of NXP board has been kept but firmware
images are adapted to be more sysupgrade friendly. At the moment
NOR and SD boots are supported.
NOR flash instructions:
* make sd card with sdboot image
* boot
* write firmware image to spi flash
$ mtd write /tmp/openwrt-layerscape-armv8_64b-fsl_ls1028a-rdb-
squashfs-firmware.bin /dev/mtd0
* change jumper to NOR boot and reset
V3:
* Added board specific network defaults for lan/wan
v2:
* Added INA220 curent monitor, PCF2129 RTC clock and NXP
SA56004ED temperature sensor to default packages
* removed compat fixups for thist board
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
The ZTE MF282 is a LTE router used (exclusively?) by the network operator
"3".
Specifications
==============
SoC: QCA9563 (775MHz)
RAM: 128MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 1x GBit LAN
LTE: ZTE MF270 (Cat4), detected as P685M
WiFi: QCA9880ac + QCA9560bgn
MAC addresses
=============
LAN: from config
WiFi 1: from config
WiFi 2: +1
Installation
============
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x82000000 openwrt.bin
bootm 0x82000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download.
Once booted, transfer the sysupgrade image and run sysupgrade.
LTE Modem
=========
The LTE modem is probably the same as in the MF283+, all instructions
apply.
Configuring the connection using modemmanager works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Rename to Fritz!Box to keep naming uniform.
Fixes: ceac4ae3b4 ("lantiq: xway: add support for AVM FRITZ!Box 7330")
Signed-off-by: Nick Hainke <vincent@systemli.org>
The current problems blocking the switch to the kernel 5.15 are
related to the GSWIP driver. This driver is only used by the
xrx200 subtarget. The other subtargets are unaffected by this
problem.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kernel setting CONFIG_IO_URING supports high-performance I/O for file
access and servers, generally for more performant platforms, and adds
~45 KB to kernel sizes. The need for this on less "beefy" devices is
questionable, as is the size cost considering many platforms have kernel
size limits which require tricky repartitioning if outgrown. The size
cost is also large relative to the ~180 KB bump expected between major
OpenWRT kernel releases.
No OpenWrt packages have hard dependencies on this; samba4 and mariadb
can take advantage if available (+KERNEL_IO_URING:liburing) but
otherwise build and work fine.
Since CONFIG_IO_URING is already managed via the KERNEL_IO_URING setting
in Config-kernel.in (default Y), remove it from those target configs
which unconditionally enable it, and update the defaults to enable it
conditionally only on more powerful 64-bit x86 and arm devices. It may
still be manually enabled as needed for high-performance custom builds.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Since CONFIG_DYNAMIC_DEBUG is already managed via the KERNEL_DYNAMIC_DEBUG
setting in Config-kernel.in (default N), remove or disable it in target
configs which unconditionally enable it, along with the related setting
CONFIG_DYNAMIC_DEBUG_CORE. This saves several KB in the kernels for
ipq40xx, ipq806x, filogic, mt7622, qoriq, and sunxi.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This activates CONFIG_SLAB_FREELIST_RANDOM.
This option make the free list less predictable. This makes it harder to
exploit heap based security vulnerabilities.
This adds a little bit more code to the kernel and a small additional
compute overhead.
This option is activated in Debian by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The target is currently broken with Kernel 5.15 and no one in sight to
fix it. Instead of stalling the next release indefinitely, make it
source only and see if someone steps up to fix it.
Signed-off-by: Paul Spooren <paul.spooren@rhebo.com>
The target is currently broken with Kernel 5.15 and no one in sight to
fix it. Instead of stalling the next release indefinitely, make it
source only and see if someone steps up to fix it.
Signed-off-by: Paul Spooren <paul.spooren@rhebo.com>
Rename existing device to v1 and create common .dtsi
Difference to v1: 16MB Flash
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 16 MB (SPI NOR, XM25QH128C on my device)
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Buttons: Reset, WPS
LEDs: Two Power LEDs (blue and red; together they form purple)
Power: DC 12V 1A center positive
Serial: 115200 8N1
C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2
(P - G - R - T) | v2 labels them on the board
Installation:
Download and flash the manufacturer's built OpenWrt image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWrt image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
Connect to any lan ethernet port
Power on the device while holding the reset button
Wait at least 8 seconds before releasing reset button for image to
download
MAC addresses as verified by OEM firmware:
use address source
LAN f4:a4:54:86:75:a2 label
WAN f4:a4:54:86:75:a3 label + 1
2g f4:a4:54:86:75:a2 label
5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
The switch driver actually expects every port to have a PHY handle, and
several branches in the code determine if a port is valid by checking
for a non-zero phy field.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The RealTek 2.5G PHY providing the WAN port of the Netgear WAX206 has
previously been hard-coded in the device tree. Now that the PHY can be
probed correctly also via Clause-45 MDIO, use that instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Early versions (?) of the RTL8221B PHY cannot be identified in a regular
Clause-45 bus scan as the PHY doesn't report the implemented MMDs
correctly but returns 0 instead.
Implement custom identify function using the PKGID instead of iterating
over the implemented MMDs to work-around this problem.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit adds factory.bin image for TP-Link EC330-G5u v1. This allows
to install OpenWrt without connecting a serial cable (UART).
Installation using factory image
--------------------------------
Tested with "3.16.0 0.9.1 v6037.0 Build 191016 Rel.30619nb" TP-Link
firmware.
1. Login to the router web interface (http://192.168.0.1/ by default) and
save running config to "conf.bin" file
2. Open configuration file in any TP-Link config editor (e.g.
https://jahed.github.io/tp-link-config-editor/)
3. Find "DeviceInfo" section and insert a new string "<Description
val="Modem Router`telnetd -p 1023 -l login`" />" according to the
following example:
<DeviceInfo>
...
<Description val="Modem Router`telnetd -p 1023 -l login`" />
...
</DeviceInfo>
4. Save configuration file and upload changed configuration using stock
firmware interface
5. Login using telnet to IP:192.168.0.1 (Username:admin, password:1234)
6. Run "cat /proc/mtd | grep mtd7"
a. If the result is 'mtd7: 03000000 00020000 "rootfs" 03400000',
then install stock firmware using web interface to toggle booted
firmware image from "os1" to "os0"
b. If the result is 'mtd7: 03000000 00020000 "rootfs" 00400000',
then all is ok, go to the next step
7. Set up a tftp server with OpenWrt factory.bin image (IP:192.168.0.100
in this example)
8. Login using telnet to 192.168.0.1
9. Download OpenWrt factory.bin image from the tftp server:
cd /tmp
tftp -g -r factory.bin 192.168.0.100
10. Write OpenWrt factory.bin image:
dd if=/tmp/factory.bin of=/dev/mtdblock1
11. Power cycle the router
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The TP-Link EC330-G5u v1 router has MAC address that stored in factory mtd
in ascii format. This commit makes the router use of "mac-address-ascii"
in dts.
After the change:
1. All MAC addresses are explicitly assigned in dts (the workarounds in
network scripts are no longer needed);
2. gmac0 (eth0) MAC address is no longer random.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* Delete unused lantiq makefile
* Delete redundant makefiles and unify them into the main makefile
* Refactor and unify board code into a single file
* Add support and review subtarget specific board support
Signed-off-by: Antonio Vázquez <antoniovazquezblanco@gmail.com>
This deactivates the kernel option CONFIG_OABI_COMPAT.
The old arm OABI is not needed any more, we compile all applications for
the new ARM EABI.
This reduces the attack surface of the kernel syscall interface.
On all other targets CONFIG_OABI_COMPAT is already deactivated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This deactivates the CONFIG_COMPAT kernel option.
With CONFIG_COMPAT the kernel will provide syscall interfaces for arm32
binaries in addition to the interfaces needed for arm64 binaries.
In OpenWrt the complete userspace is compiled for this specific
architecture and support for 32 bit ARM applications is not needed.
This reduces the size and the attack surface for the systems.
On all other targets CONFIG_COMPAT is already deactivated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The legacy (BSD) PTY support could open security problems in a system,
We do not need them in OpenWrt, deactivate this option in all targets.
Debian also deactivates this option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates the CONFIG_ARM64_SW_TTBR0_PAN option for all arm64
kernels by default.
The CONFIG_ARM64_SW_TTBR0_PAN option prevents the kernel form accessing
user space memory directly. This makes it harder to exploit the kernel.
This is activated by default and was already activate on all other arm64
targets before.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates CONFIG_HARDENED_USERCOPY for the remaining targets. This
adds additional checks in the copy_from_user() and copy_to_user()
functions.
This was not activated for ARCHS38 before because of a bug in the Linux
kernel 5.4 till 5.14, which as fixed and is described here:
https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/15
I do not know why this was deactivated for mt7629 and rockchip.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.
Specifications
==============
SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)
MAC address assignment
======================
The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.
The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.
Installation (web interface)
============================
The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.
The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.
1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy
NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.
Installation (UART method)
==========================
The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:
1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation
Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:
nand read 1800000 53c0000 800
mw.b 1800004 1 1
nand erase 53c0000 800
nand write 1800000 53c0000 800
This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.
Back to stock
=============
It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.
It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:
mtd write zyxel.bin Kernel2
echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
This activates the CONFIG_SCHED_STACK_END_CHECK option.
The kernel will check if the kernel stack overflowed in the schedule()
function. This just adds a very small computational overhead.
This option is activated in Debian by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates some extra checks in SLAB or SLUB to make it harder to
execute kernel heap exploits. This adds a minor performance
degradation which I haven't measured-.
Many mainstream Linux distributions also activate this option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates the following kernel options by default:
* CONFIG_RANDOM_TRUST_CPU
* CONFIG_RANDOM_TRUST_BOOTLOADER
With these option Linux will also use data from the CPU RNG e.g. RDRAND
and the bootloader to initialize the Linux RNG if such sources are
available.
These random bits are used in addition to the other sources, no other
sources are getting deactivated. I read that the Chacha mixer isn't
vulnerable to injected entropy, so this should not be a problem even if
these sources might inject bad random data.
The Linux kernel suggests to activate both options, Debian also
activates them. This does not increase kernel code size.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It was brought to attention the Archer AX23 v1 fails to read jffs2 data
from time to time. While this is not reproducible on my unit, it is on
others.
Reducing the SPI frequency does the trick. While it worked with at lest
40 MHz, opt for the cautious side and choose a save frequency of 25 MHz.
Apply the same treatment to the Mercusys MR70X which uses a similar
design just in case.
Signed-off-by: David Bauer <mail@david-bauer.net>
OpenWrt's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in the case of hack-5.15 patches which are not meant for
upstream, adding proper fields allows for `git am` to properly function.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- irq_domain_add_simple() can't be used on bmips since interrupts aren't
hardcoded with specific offsets for internal and external as opposed to
bcm63xx. This is needed to avoid collisions with other interrupts.
- remove unused bcm63xx-specific code.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There's no need to poll the gpio keys every 20 ms and the linux kernel
documentation suggests 100 ms.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The current bcma SPROM extraction from upstream only supports SPROMs with
revisions from 8 to 11.
Let's align the downstream fallback driver with upstream.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Remove unneeded mac bytes from struct (it's already present in the SPROM).
- Convert devid_override to boolean.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Remove unneeded mac bytes from struct (it's already present in the SPROM).
- Convert devid_override to boolean.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Convert GL-AP1300 to DSA and enable it.
While working on it rename the GL-AP1300 leds from green to white.
Tested-by: Rob White <rob@blue-wave.net>
Tested-by: Robert Sommer <frauhottelmann@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
As was done in commit e11d00d44c ("ath79: create Aruba AP-105 APBoot
compatible image"), alter the Aruba AP-175 image generation process so
OpenWrt can be loaded with the vendor Aruba APBoot. Since the
remainder of the explanation and installation process is identical,
continuing the quote from that commit:
This works by prepending the OpenWrt LZMA loader to the uImage and
jumping directly to the loader. Aruba does not offer bootm on these
boards.
This approach keeps compatibility to devices which had their U-Boot
replaced. Both bootloaders can boot the same image.
With this patch, new installations do not require replacing the
bootloader and can be performed from the serial console without
opening the case.
Installation
------------
1. Attach to the serial console of the AP-175.
Interrupt autoboot and change the U-Boot env.
$ setenv apb_rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x84000000 ap175.bin; go 0x84000040"
$ setenv apb_fb_openwrt "cp.b 0xbf040000 0x84000000 0x10000;
go 0x84000040"
$ setenv bootcmd "run apb_fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap175.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run apb_rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
The previous attempt to replace an open coded paged read in the RealTek
Ethernet PHY driver was too naive and resulted in breaking the r8169
PCIe Ethernet driver which also makes use of the RealTek Ethernet PHY
driver.
Fix this by instead of using the (not yet populated) paged operations
rather use rtl821x_write_page and protect the whole paged read operation
using the MDIO bus mutex.
Fixes: 998b973157 ("kernel: net: phy: realtek: improve RealTek 2.5G PHY driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It was found this device uses a single tri-color power/status LED
rather than individual red/orange LEDs, which also supports green.
Add GPIO for green color and use with `boot` and `running` aliases.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
- Correct WiFi MACs, they didn't match oem firmware
- Move nvmem-cells to bdinfo partition and remove &bdinfo reference
- Add OEM device model name R13 to SUPPORTED_DEVICES
This allows sysupgrading from Cudy's OpenWrt fork without force
- Label red_led and use it during failsafe mode and upgrades
MAC addresses as verified by OEM firmware:
use address source
LAN b4:4b:d6:2d:c8:4a label
WAN b4:4b:d6:2d:c8:4b label + 1
2g b4:4b:d6:2d:c8:4a label
5g b6:4b:d6:3d:c8:4a label + LA-Bit set + 4th oktet increased
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[read wifi mac from flash offset]
Signed-off-by: David Bauer <mail@david-bauer.net>
The Alcatel HH40V is a CAT4 LTE router used by various ISPs.
Specifications
==============
SoC: QCA9531 650MHz
RAM: 128MiB
Flash: 32MiB SPI NOR
LAN: 1x 10/100MBit
WAN: 1x 10/100MBit
LTE: MDM9607 USB 2.0 (rndis configuration)
WiFi: 802.11n (SoC integrated)
MAC address assignment
======================
There are three MAC addresses stored in the flash ROM, the assignment
follows stock. The MAC on the label is the WiFi MAC address.
Installation (TFTP)
===================
1. Connect serial console
2. Configure static IP to 192.168.1.112
3. Put OpenWrt factory.bin file as firmware-system.bin
4. Press Power + WPS and plug in power
5. Keep buttons pressed until TFTP requests are visible
6. Wait for the system to finish flashing and wait for reboot
7. Bootup will fail as the kernel offset is wrong
8. Run "setenv bootcmd bootm 0x9f150000"
9. Reset board and enjoy OpenWrt
Installation (without UART)
===========================
Installation without UART is a bit tricky and requires several steps too
long for the commit message. Basic steps:
1. Create configure backup
2. Patch backup file to enable SSH
3. Login via SSH and configure the new bootcmd
3. Flash OpenWrt factory.bin image manually (sysupgrade doesn't work)
More detailed instructions will be provided on the Wiki page.
Tested by: Christian Heuff <christian@heuff.at>
Signed-off-by: Andreas Böhler <dev@aboehler.at>
The RTL8366S/RB switch node in DTS defines "mii-bus = <&mdio0>" to permit
management via SMI but this has likely never worked, instead falling back
to using GPIOs in the past:
rtl8366s switch: cannot find mdio bus from bus handle (yet)
rtl8366s switch: using GPIO pins 19 (SDA) and 20 (SCK)
rtl8366s switch: RTL8366 ver. 1 chip found
Recently, the rtl8366s and rtl8366_smi drivers were changed from built-in
to loadable modules. This affected driver probing order and caused switch
initialization (and network access) to fail:
rtl8366s switch: using MDIO bus 'ag71xx_mdio'
rtl8366s switch: unknown chip id (ffff)
rtl8366s switch: chip detection failed, err=-19
Force using GPIOs to manage the switch by dropping the "mii-bus" DTS
definition, which works for both built-in and loadable switch drivers.
Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module")
Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module")
Tested-by: Tony Ambardar <itugrok@yahoo.com> # WZR-HP-G300NH (RTL8366S)
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Switch drivers for RTL8366S/RB were packaged as modules but not properly
added to device definitions for WZR-HP-G300NH router variants, breaking
network access to both after installation or upgrade.
Assign the correct switch driver package for each router.
Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module")
Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #11919
Signed-off-by: Haoan Li <lihaoan1001@163.com>
Apart from the embedded BCM63268 wireless, this device has an external BCM4360
connected by PCIe which needs a fallback SPROM.
b43 isn't enabled for this device because BCM4360 isn't supported (AC PHY).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Apart from the embedded BCM6362 wireless, Netgear DGND3700v2 has external
BCM43228 wireless connected by PCIe.
Fallback SPROM isn't needed for this one because it has a physical SPROM.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
late_initcall_sync() is no longer needed so standard module functions can be
used on all bmips PCI/PCIe drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Stop using bmips b43-sprom fixups and switch to generic bcma/ssb fallback
SPROMs. This way we don't need to include the b43-sprom fixups on devices
without Broadcom wireless.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds generic kernel support for Broadcom Fallback SPROMs so that it can be
used in any target, even non Broadcom ones.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
A patch was added in kernel 5.4 to support the fiber operation of
AR8033 with ramips devices. In kernel 5.18 similar enhancements
were added to the kernel. Those patches are required for other
fiber based devices but when added, build fails for ramips targets.
This commit removes the ramips patch and adds the kernel 5.18 ones.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
[ split commit,refresh patch and improve commit message ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
A patch was added in kernel 5.4 to support the fiber operation of
AR8033 with ramips devices. In kernel 5.18 similar enhancements
were added to the kernel. Those patches are required for other
fiber based devices but when added, build fails for ramips targets.
This commit removes the ramips patch and adds the kernel 5.18 ones.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
[ split commit, refresh patch and improve commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace pending 730-net-phy-at803x-fix-feature-detection.patch with
upstream version and move it to backport.
Refresh other related patch while moving it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The patch needs to be refreshed to apply cleanly.
Fixes: 998b973157 ("kernel: net: phy: realtek: improve RealTek 2.5G PHY driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: ESMT M15T4G16256A 512MB
Ethernet (Max Speed):
XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan
XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
WiFi:
XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R)
XDR6086/XDR6088:
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 4A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
[Add uboot build, fit and sysupgrade support, fix RealTek PHYs]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* use interface mode switching only when operating in C45 mode
Linux prevents switching the interface mode when using C22 MDIO,
hence use rate-adapter mode in case the PHY controlled via C22.
* use phy_read_paged where appropriate
* use existing generic inline functions to handle 10GbE advertisements
instead of redundantly defining register macros in realtek.c which
are not actually vendor-specific.
* make sure 10GbE advertisement is valid, preventing false-positive
warning "Downshift occurred from negotiated speed 2.5Gbps to actual
speed 1Gbps, check cabling!" with some link-partners using 1G mode.
* Support Link Down Power Saving Mode (ALDPS)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of use mac-address-ascii in nvmem_get_mac_address
function, move it into of_get_mac_addr_nvmem function to
support more devices.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The Config partition of some machines is special, and the openwrt script
cannot read the protest_lan_mac correctly. This problem can be solved by
reading the mac address (ascii) in dts.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix the network configuration according to the device tree.
Fixes: 5faff99 ("mediatek: filogic: fix mt7986a ethernet devicetree entries")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
