Commit Graph

23430 Commits

Author SHA1 Message Date
Yangbo Lu
5ca8903631 layerscape: convert to squashfs rootfs for QSPI NOR boot
There had been an issue in Layerscape QSPI driver for very long
time, which made squashfs,jffs2 rootfs not work on QSPI NOR.
And the ubifs had been used as a workaround.
Now the issue has been fixed. So convert to use squashfs,jffs2
rootfs on QSPI NOR for Layerscape boards (LS1012ARDB/LS1046ARDB/
LS1088ARDB), and update u-boot bootargs for booting.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-07-11 14:44:22 +02:00
Alexey Dobrovolsky
ecda6b791b ramips: kernel: fix awake-rt305x-dwc2 patch
At this point in v5.4 kernel we cannot use dwc2_readl() and
dwc2_writel() since they rely on the value hsotg->needs_byte_swap
which cannot be obtained before the controller wakes up.
We should use readl() and writel() to wake up the controller before
calling dwc2_check_core_endianness().

Fixes: 6be0da90a1 ("ramips: refresh patches")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed Fixes: tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-11 13:33:28 +02:00
Pawel Dembicki
67ce9aedd6 kirkwood: add support for Check Point L-50
This patch adds support for the Check Point L-50 from 600/1100 series
routers.

Specification:
-CPU: Marvell Kirkwood 88F6281 1200MHz
-RAM: 512MB
-Flash: NAND 512MB
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4))
-USB: 2x USB2.0
-Express card slot
-SD card slot
-Serial console: RJ-45 115200 8n1
-Unsupported DSL

Known issues:
-DSL not supported
-Expresscard not tested

Installation:

Step one -> backup:
make backup u-boot and env for revert stock posibility
make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr

Step two -> Use kwboot tool to upload openwrt u-boot to RAM:

run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t"
end start u-boot

Step three -> Restore macs (e.g. below):
setenv eth1addr 00:1C:XX:XX:XX:6C
setenv ethaddr 00:1C:XX:XX:XX:6B
setenv lan1_mac_addr 00:1C:XX:XX:XX:6C
setenv lan2_mac_addr 00:1C:XX:XX:XX:6D
setenv lan3_mac_addr 00:1C:XX:XX:XX:6E
setenv lan4_mac_addr 00:1C:XX:XX:XX:6F
setenv lan5_mac_addr 00:1C:XX:XX:XX:70
setenv lan6_mac_addr 00:1C:XX:XX:XX:71
setenv lan7_mac_addr 00:1C:XX:XX:XX:72
setenv lan8_mac_addr 00:1C:XX:XX:XX:73
setenv dmz_mac_addr 00:1C:XX:XX:XX:74
setenv dsl_mac_addr 00:1C:XX:XX:XX:75

Step four -> flash u-boot:
mw 0x0800000 0xffff 0x100000
nand erase 0x0 100000
tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb
nand write 0x0800000 0x0 0x100000
saveenv

Step five -> run initramfs image:

tftpboot 0x02000000 openwrt.bin; bootm 0x02000000;

Step six -> install sysupgrade OpenWrt image:

copy to /tmp/ sysupgrade image
run sysupgrade

Back to stock:
Restore original u-boot end env.
Install factory image via stock u-boot.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-11 13:33:28 +02:00
John Audia
039fd27173 kernel: bump 5.4 to 5.4.51
update via update_kernel.sh -v -u 5.4

Removed upstreamed patches:
 350-MIPS-Add-missing-EHB-in-mtc0-mfc0-sequence-for-DSPen.patch

Script refreshed patches:
 902-debloat_proc.patch
 904-debloat_dma_buf.patch

Attempted merge conflict in following patches:
 0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch

Build system: x86_64
Build tested: ipq806x (Netgear R7800)

Signed-off-by: John Audia <graysky@archlinux.us>
[fixed sha256sum of the tarball]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-11 13:33:28 +02:00
Pawel Dembicki
f93267bccf ipq806x: enable Linksys EA8500 eth1 interface
At this moment Linksys EA8500 uses only eth0.

This patch change switch registers, which allow to use eth1 as lan
and eth0 as wan. The method work with similar Linksys EA7500V1
and it work with EA8500.

Suggested-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Brian Onn <brian.a.onn@gmail.com>
Tested-by: Adrian Panella <ianchi74@outlook.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-11 13:33:28 +02:00
Adrian Schmutzler
bc85cc2b42 ath79: disable TP-Link TL-WR941ND v2
The support for this device's Marvell MV88E6060 switch has been
reported to be broken with kernels 4.19/5.4 (see bug report).

Since this a 4/32 device and it has been confirmed to be working
with stable 19.07 release (kernel 4.14), and since fixing it does
not seem trivial, let's just disable it in master.

Fixes: FS#2524

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-11 11:47:47 +02:00
Tim Thorpe
edbc8e5512 ramips: add support for Netgear R6020
This adds support for the Netgear R6020, aka Netgear AC750.

The R6020 appears to be the same hardware as the Netgear R6080,
aka Netgear AC1000, but it has a slightly different flash layout,
and no USB ports.

Specification:

SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB

MAC addresses based on vendor firmware:
LAN      *:88   0x4
WAN      *:89
WLAN2    *:88   0x4
WLAN5    *:8a   0x8004

The factory partition might have been corrupted beforehand. However,
the comparison of vendor firmware and OpenWrt still allowed to retrieve
a meaningful assignment that also matches the other similar devices.

Installation:

Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6020, and power the R6020 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6020. After flashing has finished,
power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.

Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
[slightly extend commit message, fix whitespaces in DTS, align From:
with Signed-off-by]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-10 11:39:05 +02:00
Willem van den Akker
0df71e01cf lantiq: set correct gphy pins for Zyxel P-2812
This fixes the gphy LED pins for Zyxel P-2812 devices. The have
been accidentally altered during a tidy-up operation (see Fixes:
below).

No ports were available, dmesg reported:

[ 0.658577] pinctrl-xway 1e100b10.pinmux: pin io5 already requested by
            1e100bb0.stp; cannot claim for 1e108000.eth
[ 0.667566] pinctrl-xway 1e100b10.pinmux: pin-5 (1e108000.eth) status -22
[ 0.685238] lantiq,xrx200-net 1e108000.eth: Error applying setting,
            reverse things back
[ 0.693270] lantiq,xrx200-net: probe of 1e108000.eth failed with error -22

Fixes: FS#3188
Fixes: 660200e53d ("lantiq: dts: assign the GPHY LED pins to the
Ethernet controller node")

Suggested-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Willem van den Akker <wvdakker@wilsoft.nl>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-10 10:06:34 +02:00
David Woodhouse
f632747704 mediatek: fix bashism in gen_banana_pi_img.sh
There was a bashism in the script. This fixes the script so that it
doesn't actually require bash, and can be run with any POSIX shell as
its shebang suggests.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-09 11:11:31 +02:00
Sungbo Eo
36105880ee mediatek: re-add u3phy2 phy-switch patch
This patch is required for pcie@2,0 in mt7623 to work. The patch was originally
added in kernel 4.14, but it has not been ported to 4.19 and later.

Fixes: FS#3217
Tested-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-09 10:28:40 +02:00
Sungbo Eo
923792369e mediatek: do not create device nodes in uci-defaults script
Since commit 298814e6be ("base-files: config_generate: split macaddr with
multiple ifaces") uci MAC address setup will create a device node for each
member iface. But this script might override the device nodes and interfere
with the MAC address setup.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-09 10:28:40 +02:00
Petr Štetiar
c7b750e7ac treewide: kernel: drop redundant USB_EHCI_HCD=n config symbol
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.

Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-09 10:28:40 +02:00
Sebastian Schaper
361c670a46 ath79: add support for D-Link DAP-1330/DAP-1365 A1
Port device support for DAP-1330 from the ar71xx target to ath79.

Additionally, images are generated for the European through-socket
case variant DAP-1365. Both devices run the same vendor firmware, the
only difference being the DAP_SIGNATURE field in the factory header.
The vendor's Web UI will display a model string stored in the flash.

Specifications:

 * QCA9533, 8 MiB Flash, 64 MiB RAM
 * One Ethernet Port (10/100)
 * Wall-plug style case (DAP-1365 with additional socket)
 * LED bargraph RSSI indicator

Installation:

 * Web UI: http://192.168.0.50 (or different address obtained via DHCP)
   There is no password set by default
 * Recovery Web UI: Keep reset button pressed during power-on
   until LED starts flashing red, upgrade via http://192.168.0.50
 * Some modern browsers may have problems flashing via the Web UI,
   if this occurs consider booting to recovery mode and flashing via:
   curl -F \
     files=@openwrt-ath79-generic-dlink_dap-1330-a1-squashfs-factory.bin \
     http://192.168.0.50/cgi/index

The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-07-09 10:28:40 +02:00
Sungbo Eo
358aec7775 ath79: add support for Arduino Yun
Arduino Yun is a microcontroller development board, based on Atmel
ATmega32u4 and Atheros AR9331.

Specifications:
- MCU: ATmega32U4
- SoC: AR9331
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
- Ethernet: 1x 10/100Mbps
- USB: 1x 2.0
- MicroSD: 1x SDHC

Notes:
- Stock firmware is based on OpenWrt AA.
- The SoC UART can be accessed only through the MCU.
  YunSerialTerminal is recommended for access to serial console.
- Stock firmware uses non-standard 250000 baudrate by default.
- The MCU can be reprogrammed from the SoC with avrdude linuxgpio.

Installation:
1.  Update U-Boot environment variables to adapt to new partition scheme.
    > setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
    > setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
    > saveenv
2.  Boot into stock firmware normally and perform sysupgrade with
    sysupgrade image.
    # sysupgrade -n -F /tmp/sysupgrade.bin

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-08 23:22:30 +02:00
David Woodhouse
af9932c9b7 mediatek: Implement sysupgrade support for Banana Pi R2
Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
e19ffb25d9 mediatek: store MAC address in boot partition on Banana Pi R2
Like many boards, the Banana Pi R2 doesn't have permanant storage of
its MAC address, and we store the first random one that the kernel
generates in order to use it later and at least be consistent.

Store it in the FAT boot partition, just as the U7623 board (and others)
do.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
7adc29f59e mediatek: add SD card image creation for Banana Pi R2
Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
91e43a1d7a mediatek: enable SATA for mt7623
The MT7623 SoC has the same SATA block as the MT7622, so enable it in
MT7623 builds too and add it to the DEVICE_PACKAGES for those boards.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
c848bc6cd5 mediatek/mt7623: unify features and packages, add ext4 and usb
The supported MT7623 boards are mostly identical (what with being a
System-on-Chip and all), so unify the DEVICE_PACKAGES for them, and add
ext4 and usb support for them.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
c07d0d7f3e mediatek: mt7623: refresh 5.4 kernel config
Some options were not explicitly specified, causing the kernel build to
drop to interactive mode. Set the missing options.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
Sebastian Schaper
14599c5945 ath79: add support for D-Link DCH-G020 Rev. A1
The DCH-G020 is a Smart Home Gateway for Z-Wave devices.

Specifications:

 * QCA9531, 16 MiB Flash, 64 MiB RAM
 * On-Board USB SD3503A Z-Wave dongle
 * GL850 USB 2.0 Hub (one rear port, internal Z-Wave)
 * Two Ethernet Ports (10/100)

Installation:

 * Web UI: http://192.168.0.60 (or different address obtained via DHCP)
   Login with 'admin' and the 6-digit PIN Code from the bottom label
 * Recovery Web UI: Keep reset button pressed during power-on
   until LED starts flashing red, upgrade via http://192.168.0.60
 * Some modern browsers may have problems flashing via the Web UI,
   if this occurs consider booting to recovery mode and flashing via:
   curl -F \
     files=@openwrt-ath79-generic-dlink_dch-g020-a1-squashfs-factory.bin \
     http://192.168.0.60/cgi/index

Known issues:

 * Real-Time-Clock is not working as there is currently no matching driver
   It is still included in the dts as compatible = "pericom,pt7c43390";
 * openzwave was tested on v19.07 (running MinOZW as a proof-of-concept),
   but the package grew too big as lots of device pictures were included,
   thus any use of Z-Wave is up to the user (e.g. extroot and domoticz)

The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-07-08 22:54:34 +02:00
John Audia
3e992ea790 ipq806x: compile in schedutil governor
Gives users a third option to augment ondemand and performance. Kernel
docs[1] explain differences and this PR empowers users w/ the choice to
select between the older ondemand and newer and more simplistic schedutil
should they wish to use one that is not the performance governor.

1. Documentation/admin-guide/pm/cpufreq.rst

Signed-off-by: John Audia <graysky@archlinux.us>
[fixed From: to match SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 22:54:13 +02:00
Furkan Alaca
541faf2c93 ramips: mt7621: use lzma-loader for ra21s & rg21s
The rg21s fails to boot if the kernel is larger than about
2,376 KiB. The ra21s is virtually identical hardware.
Enabling lzma-loader resolves the issue on both the rg21s
and ra21s (see FS#3057 on the issue tracker).

Fixes: FS#3057
Signed-off-by: Furkan Alaca <furkan.alaca@queensu.ca>
2020-07-08 22:52:40 +02:00
Sergei Burakov
4dc9ad4af8 ramips: add support for ZyXEL Keenetic Lite Rev.B
Device specification:

SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: None
8x LED, 2x button

Flash instruction:

Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-lite-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Sergei Burakov <senior.anonymous@ya.ru>
2020-07-08 22:52:40 +02:00
Adrian Schmutzler
9e6257c26c ramips: move adslr_g7 in image/mt7621.mk to keep sorting
Move this device to the top to maintain alphabetic sorting in the
file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 21:20:19 +02:00
Adrian Schmutzler
7de08be913 ramips: add missing kmod-mt7615-firmware for TP-Link RE500 v1
Adding this has been overlooked when rebasing the commit prior to
merge.

Fixes: ba0f4f0cfd ("ramips: add support for TP-Link RE500 v1")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 21:20:19 +02:00
Adrian Schmutzler
f3921acdf0 ipq40xx: fix patches on dts Makefile
The patches for arch/arm/boot/dts/Makefile have not been updated
in a syntactically correct way (just body was changed). Fix it.

Fixes: 4a77a060ab ("ipq40xx: add support for Buffalo WTR-M2133HP")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 17:50:12 +02:00
Bjørn Mork
c1794d653c ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)
Hardware
--------
SoC:   MediaTek MT7621ST
WiFi:  MediaTek MT7603
       Quantenna QT3840BC
Flash: 128M NAND
RAM:   64M
LED:   Dual colour red and green
BTN:   Reset
       WPS
Eth:   4 x 10/100/1000 connected to MT7621 internal switch
       MT7621 RGMII port connected to Quantenna module
GPIO:  Power/reset of Quantenna module

Quantenna module
----------------

The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation.  It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621.  It loads both a second uboot stage and an os
image from the MT7621 using tftp.  The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.

There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.

Serial ports
------------

Two serial ports with headers:

RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1   -  57600 8N1 - Connected to the MT7621 console

Both share pinout with many other Zyxel/Mitrastar devices:

1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND

Dual system partitions
----------------------

The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.

OpenWrt does not support this scheme and will always use the
first OS partition.  It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.

Installation from vendor firmware
---------------------------------

1. Run a DHCP server. The WAP6805 is configured as a client device
   and does not have a default static IP address. Make a note of
   which address it is assigned

2. tftp the OpenWrt initramfs-kernel.bin image to this address.
   Wait for the WAP6805 to reboot.

3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
   backup of all mtd partitions now.  The last used OEM image is
   still present in either "Kernel" or "Kernel2" at this point,
   and can be restored later if you save a copy.

4. sysupgrade to the OpenWrt sysupgrade.bin image.

Installation from U-Boot
------------------------

This requires serial console access

1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
   your tftp server directory.  Configure the server address as
   192.168.0.33/24

2. Hit ESC when the message "Hit ESC key to stop autoboot"
   appears

3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.

4. Answer Y to the question "Erase Linux in Flash then burn new
   one. Are you sure?", and answer the address/filename questions.
   Defaults:
        Input device IP (192.168.0.2)
        Input server IP (192.168.0.33)
        Input Linux Kernel filename ("ras.bin")

5. Wait until after you see the message "Done!" and power cycle
   the device.  It will hang after flashing.

6. Continue with step 3 and 4 from the vendor firmware procedure.

Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme.  These changes appear to have
broken a few things.  The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work.  The image selection
scheme is unreliable and inconsistent.  A limited U-Boot menu is
available - and used by the above U-Boot install procedure.  But
direct booting into an uploaded image does not work, neither with
ram nor with flash.  Flashing works, but requires a hard reset after
it is finished.

Reverting to OEM firmware
-------------------------

The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.

  ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin

OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required.  See above.

Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware.  But the branding features do obviously
differ.

LED controller
--------------

Hardware implementation is unknown.  The dual-color LED is controlled
by 3 GPIOs:

  4: red
  7: blinking green
 13: green

Enabling both red and green makes the LED appear yellow.

The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
20c7abd4b7 ipq806x: add support for Linksys EA7500 V1
This patch adds support for the Linksys EA7500 V1 router.

Specification:
 - CPU: Qualcomm IPQ8064
 - RAM: 256MB
 - Flash: NAND 128MB
 - WiFi: QCA9982 an+ac + QCA9983 bgn
 - Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
 - USB: 1x USB 3.0 1x USB2.0
 - Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
 - 2 Buttons
 - 1 LED

Known issues:
 - Some devices won't flash via web gui

Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.

Serial + TFTP method:
 - downgrade to 1.1.2 two times
 - connect ehternet and serial cable
 - set ip address of tftp server to 192.168.1.254
 - put openwrt factory image to tftp folder and rename it to macan.bin
 - stop device while booting in u-boot
 - run command: "run flashimg"
 - run command: "setenv boot_part 1"
 - run command "saveenv"
 - reset

Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F

Tested by github users: @jack338c and @grzesiczek1

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 16:07:05 +02:00
Yanase Yuki
4a77a060ab ipq40xx: add support for Buffalo WTR-M2133HP
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.

Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A

Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
   and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
    # ubidetach -p /dev/mtd15
    # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
    # fw_setenv bootcmd bootipq
8. Perform reboot.

Recover to stock firmware
-------------------------
1. Execute the following command.
    # fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
d2c3131b3f kirkwood: add support for Zyxel NSA310S
Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6702 1 GHz
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 2x USB 2.0
 - 1x SATA
 - 3x button
 - 7x leds
 - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)

Known issues:
 - no kernel module for RTC. [*]
 - buzzer (connected to MPP43) need to be drived by 1kHz signal
 - no kernel module for internal MCU connected via I2C[**]

[*]
Karoly Pocsi made simple, unofficial driver for HT1382.
It can be found here:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

[**]
Karoly Pocsi found how CPU talk with MCU:
It is possible to query the MCU-controlled fan speed and temperature:
i2cget -y 0x0 0x0a 0x07
i2cget -y 0x0 0x0a 0x08
The first value (0x07) is the temperature in ° C, the second (0x08) is
the time in milliseconds to complete one fan revolution (rpm = 60,000 / value).
Info translated from:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

Installation:

TFTP:
1. Run serial console and go to u-boot.
2. Copy u-boot via tftp and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftp 0x0800000 nsa310s-u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
3. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
4. Copy and run initramfs image
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftpboot zyxel_nsa310s-initramfs-uImage
	=> bootm 0x800000
5. Download sysupgrade image and perform sysupgrade

USB:

1. Prepare usb fat32 drive with u-boot.kwb and initramfs image.
   Stick it to USB 2.0 port.
2. Run serial console and go to u-boot.
3. Copy u-boot from usb and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> usb start
	=> fatload usb 0 0x0800000 u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
4. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
5. Copy and run initramfs image:
	=> usb start
	=> fatload usb 0 0x0800000 initramfs-uImage
	=> bootm 0x800000
6. Download sysupgrade image and perform sysupgrade.

Based on work ThBexx <thomas.beckler@hotmail.com>
DTS based on dropped support in 0ebdf0c.

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[NSA310s -> NSA310S in DEVICE_MODEL]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Andrey Bondar
ba59021d64 ath79: add support for 8devices Lima board
Specification:

  • 650/600/216 MHz (CPU/DDR/AHB)
  • 64 MB of RAM (DDR2)
  • 32 MB of FLASH
  • 2T2R 2.4 GHz
  • 2x 10/100 Mbps Ethernet
  • 1x USB 2.0 Host socket
  • 1x miniPCIe slot
  • UART for serial console
  • 14x GPIO

Flash instructions:

Upgrading from ar71xx target:

  • Upload image into the board:
    scp openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin
    root@192.168.1.1/tmp/
  • Run sysupgrade
    sysupgrade -F /tmp/openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin

Upgrading from u-boot:

  • Set up tftp server with
    openwrt-ath79-generic-8dev_lima-initramfs-kernel.bin
  • Go to u-boot (reboot and press ESC when prompted)
  • Set TFTP server IP
    setenv serverip 192.168.1.254
  • Set device ip from the same subnet
    setenv ipaddr 192.168.1.1
  • Copy new firmware to board
    tftpboot 0x82000000 initramfs.bin
  • Boot OpenWRT
    bootm 0x82000000
  • Upload image openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin into
    the board
  • Run sysupgrade.

Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
2020-07-08 16:07:05 +02:00
Sergio E. Nemirowski
645b1ec3e2 build: add 'make kernel_xconfig' command
This adds the kernel_xconfig make target.

Signed-off-by: Sergio E. Nemirowski <sergio@outerface.net>
2020-07-08 16:07:05 +02:00
Dongming Han
f103321349 ipq40xx: add support for GL.iNet GL-S1300
Specifications:
SOC:        Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM:        512 MiB
FLASH1:     16 MiB NOR - SPI0
FLASH2:     8 GiB eMMC
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT:      Reset, WPS
LED:        Power, Mesh, WLAN
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2:      On board with BLE module
SPI1:       On board socket for Zigbee module

Install via tftp
- NB: need to flash transition image firstly

Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf

Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-07-08 16:07:05 +02:00
Emir Efe Kucuk
53a1fede1f ramips: Add support for Xiaomi Mi Router(Black,R2100)
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"

See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg

Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot

Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo

Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client

1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0

other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)

MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004

Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
78fffc2dfd generic: platform/mikrotik: add partial AR71xx cpufreq support
This patch adds cpu frequency setting for AR724x and AR7161.
It is unknown if all the AR71xx devices support the same value range,
so support is only enabled for AR7161 at this stage.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
a874c87f4c generic: platform/mikrotik: add board_revision tag
Tag was discovered exploring the hard_config of a "r2" board.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
0217a9be0d generic: platform/mikrotik: graceful fallback for cpufreq_index
The current code would return an error on ath79 when the SoC isn't known
to the driver. Return the raw hex value instead, as happens with non
supported targets.
Also return the correctly incremented value from
sc_tag_cpufreq_ath79_arraysize()

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
2714a4faab generic: platform/mikrotik: match RouterBOOT nomenclature
RouterBOOT cpu frequency settings are letter-indexed. Follow the
same logic for the sysfs interface.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
5c4b431a3c generic: platform/mikrotik: fix routerboot_tag_show_u32s()
The routine would only accurately print out the first word.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 5ecf7d96 ("generic: routerboot sysfs platform driver")
2020-07-08 16:07:05 +02:00
Davide Fioravanti
8c13ebd3ad ramips: add support for Edimax Gemini RE23S
Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH:   1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615 (4x4:4)
  - 5GHz:   1x MT7615 (4x4:4)
  - 4 antennas: 2 external detachable and 2 internal
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x Green led (Power)
  - 1x Green-Amber-Red led (Wifi)
UART:
  - 57600-8-N-1

Everything works correctly.

Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)

Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Restoring procedure tested with RE23_1.08.bin

MAC addresses
-------------
factory 0x4     *:24
factory 0x8004  *:25
Cimage  0x07    *:24
Cimage  0x0D    *:24
Cimage  0x13    *:24
Cimage  0x19    *:25

No other addresses were found in factory partition.

Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.

Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.

If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 13:28:17 +02:00
Hauke Mehrtens
66e04abbb6 ar71xx: Fix mikrotik NAND compile problem
This Fixes the folowing compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
  nand_release(&rbni->chip);

Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-07 23:38:10 +02:00
Petr Štetiar
ae2d249056 ath79: nand: disable images for glinet_gl-ar750s
Fixes following build failures:

 WARNING: Image file glinet_gl-ar750s-nor-kernel.bin is too big
 WARNING: Image file glinet_gl-ar750s-nor-nand-kernel.bin is too big

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-07 19:47:24 +02:00
Andrey Bondar
326e488c7b ath79: add support for 8devices Rambutan board
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan

Specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 2x USB2.0 host
- 2x UART
- SPI, I2C, GPIO

Flash instructions:

Upgrade from ar71xx target:
 sysupgrade -F /tmp/openwrt-ath79-nand-8dev_rambutan-squashfs-sysupgrade.tar
or upgrade from GUI (don't save config)

Use factory image to flash from U-Boot:
 tftpboot 80060000 openwrt-ath79-nand-8dev_rambutan-squashfs-factory.ubi
 nand erase.part ubi
 nand write 80060000 ubi ${filesize}

Signed-off-by: Petr Štetiar <ynezz@true.cz> [copy&pasted missing commit description]
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
2020-07-07 19:47:24 +02:00
Adrian Schmutzler
7cb721c03f ramips: use WiFi LED DT triggers for TP-Link RE650 v1
This moves WiFi LED triggers from 01_leds to device tree.

While at it, convert the labels there to lower case; this is
more commonly used and the change will actually remove competition
between DT trigger and leftover uci config on already installed
systems.

Suggested-by: Georgi Vlaev <georgi.vlaev@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 11:57:48 +02:00
David Bauer
d8ab3216e6 ath79: switch to kernel 5.4
As the reported major bugs are ironed out, switch to the new kernel to
begin testing with a broader audience.

Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-07 10:33:17 +02:00
Aleksander Jan Bajkowski
f496939f15 lantiq: set port numbers corresponding to reg value
Fix inconsistencies found in DTS files and sort ethernet ports based on
updated names.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[squash two separate patches, rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 01:03:59 +02:00
Aleksander Jan Bajkowski
3866fefa38 lantiq: remove redundant includes from fritz736x DTS files
The removed lines are already included in vr9_avm_fritz736x.dtsi

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 00:59:51 +02:00
Christoph Krapp
ba0f4f0cfd ramips: add support for TP-Link RE500 v1
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.

TFTP recovery to stock firmware:

Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 00:40:04 +02:00
Martin Blumenstingl
982468de35 lantiq: dts: Move the &usb_vbus nodes out of &gpio
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.

This fixed the following error reported by Luca Olivetti:
  ...
  dwc2 1e101000.usb: DWC OTG Controller
  dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
  dwc2 1e101000.usb: irq 62, io mem 0x1e101000
  dwc2 1e101000.usb: startup error -517
  dwc2 1e101000.usb: USB bus 1 deregistered
  dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517

Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2020-07-06 20:23:33 +02:00
Matthew Gyurgyik
bb14d44039 kernel/pcengines-apu2: detect apuv4 board
Upstream commit 3d00da1de3 ("platform/x86: pcengines-apuv2: detect apuv4
board")

On 5.4, this module fails on APUv4 due to non-matching DMI data. With this
patch, the module will match DMI data for the APUv4.

Signed-off-by: Matthew Gyurgyik <matthew@gyurgyik.io>
[include upstream patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:33 +02:00
Lars Wessels
f855eb91b3 lantiq: added switch-config for ARV752DPW
Add missing switch config (4 LAN-Ports + CPU).

Grey WAN port (used for ADSL) is not part of the switch.

Signed-off-by: Lars Wessels <software@bytebox.org>
[rework commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:24 +02:00
Lars Wessels
702366a30b lantiq: wifi mac fix for ARV752DPW
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).

Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).

Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:13 +02:00
Sunguk Lee
2d378703f1 ramips: reduce spi-max-frequency for ipTIME A8004T
Reduce spi-max-frequency for ipTIME A8004T and disable
m25p,fast-read option.

A8004T uses `en25qh128` for the MTD.
This flash memory would allow 80MHz, sometimes kernel received
wrong id value in initramfs installed router.
(kernel expected `1c 70 18 1c 70 18`, but one of cases, it
was `9c 70 18 1c 70 18`)

In this case, openwrt can't detect the partition information,
it would write the inccorect data to the firmware partition and
also it would occur the bootlooping after sysupgrade.

Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:25:32 +02:00
Adrian Schmutzler
883250014d ipq806x: move serial0 to DTSI files
All device DTS files in the target set the serial0 property to the
same value (*). So, let's move the definitions to the DTSI files.

That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).

* The only exception is ipq8064-db149, which defines
  "serial0 = &uart2;", but inside a block called "alias" instead of
  "aliases". It must be assumed that this is broken anyway, so we
  don't touch it here.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:24:30 +02:00
Adrian Schmutzler
74e339f118 ipq806x: move stdout-path to DTSI files
All device DTS files in the target set the stdout-path to the same
value. So, let's move the definitions to the DTSI files.

That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:23:23 +02:00
Adrian Schmutzler
ed761344d2 ipq806x: disentangle and clean up SoC DTSI files
So far, the DTSI files on ipq806x had a linear inheritance:

  qcom-ipq8064.dtsi
  v
  qcom-ipq8064-v1.0.dtsi
  v
  qcom-ipq8064-v2.0.dtsi
  v
  qcom-ipq8065.dtsi

This poses problems when one wants to set something that is specific
to an architecture closer to the top of the tree.

In this patch, we remove the chain-like inheritance and have all
other files derived from qcom-ipq8064.dtsi (changing this name to
something more generic is not possible due to upstream use).

The removal of inheritance will require a few entries to be copied
from qcom-ipq8064-v2.0.dtsi to qcom-ipq8065.dtsi. However, it also
opens an opportunity for some clean-up:

- Many definitions can be improved by just using the innermost labels.

- Instead of disabling the CPU_SPC node for ipq8065, it is now off by
  default and enabled where needed.

- Instead of patching phy-tx0-term-offset into qcom-ipq8064.dtsi and
  then having it changed for qcom-ipq8064-v2.0/qcom-ipq8065, just have
  the appropriate settings done in the lower DTSI files directly.

- For the opp_table0 adjustments for ipq8065, just redefine what's
  changed, but don't add all the untouched properties again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:21:15 +02:00
Sungbo Eo
19c8f11d92 ipq806x: move common pinmux nodes to SoC DTSI
As almost same pinmux nodes are repeated in each device dts,
let's define them once in the ipq8064 dtsi and remove the rest.

* uart0_pins : Did not touch.
* i2c4_pins  : This node seems to be not used at all in dts.
               Added the most common form in the dtsi. Did not touch rpm_pins.
* spi_pins   : The common mux node is already present in the dtsi.
               Removed the duplicate nodes from dts.
* nand_pins  : Moved the entire node.
* mdio0_pins : Moved the common mux node.
* rgmii2_pins: Moved the common mux node. "pins" property is overrided in ap161.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-06 16:08:18 +02:00
Hauke Mehrtens
014d3f593a ar71xx: Fix mikrotik NAND compile problem
There is one closing bracket too much.

Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-06 00:07:38 +02:00
Scott Roberts
d31bbe40e2 mvebu: config define i2c pxa slave
We are setting CONFIG_I2C_PXA is not set
If you do set pxa to y then you have issues if you do not have
CONFIG_I2C_PXA_SLAVE is not set

Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
2020-07-04 21:12:42 +02:00
Daniel González Cabanelas
a902e6a657 mvebu: LS421DE: use automatic fan control with thermal zones
The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal
hard drives. Currently there is no control over this fan, running always
at fixed medium speed.

With the recent jump to the kernel 5.4, now we can monitor the hard drive
temperature and control the fan with thermal zones.

Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the
dts file to allow automatic fan control by the kernel.

Tested succesfully using a single Crucial BX500 SSD drive.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-07-04 21:12:42 +02:00
Hauke Mehrtens
68d9cb8214 kernel: Update kernel 5.4 to version 5.4.50
Run tested: ath79, ipq40xx
Build tested: ath79, ipq40xx

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:12:42 +02:00
Hauke Mehrtens
6062d85892 kernel: Update kernel 4.19 to version 4.19.131
Fixes:
- CVE-2020-10757

The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.

Run tested: ath79
Build tested: ath79

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:12:42 +02:00
Hauke Mehrtens
ce958dd88a kernel: Update kernel 4.14 to version 4.14.187
Fixes:
- CVE-2020-10757

The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.

Build tested: ramips

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:12:42 +02:00
Hauke Mehrtens
4bb5e331a7 kernel: Fix ath79 DSP exception at bootup
This resolves a hazard between a mtc0 and a mfc0 instruction after
activating the DSP support. Without this fix the CPU could use the old
value again and the DSP support would not be active.

Fixes: FS#2928, FS#2899
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: David Bauer <mail@david-bauer.net> [ocedo_koala/ocedo_raccoon]
2020-07-04 16:04:21 +02:00
Antti Seppälä
a175bc8f36 ath79: add support for GL.iNet GL-MiFi
Add support for the ar71xx supported GL.iNet GL-MiFi to ath79.

Specifications:
 - Atheros AR9331
 - 64 MB of RAM
 - 16 MB of FLASH (SPI NOR)
 - 2x 10/100/1000 Mbps Ethernet
 - 2.4GHz (AR9330), 802.11b/g/n
 - 1x USB 2.0 (vbus driven by GPIO)
 - 4x LED, driven by GPIO
 - 1x button (reset)
 - 1x mini pci-e slot (vcc driven by GPIO)

Flash instructions:

Vendor software is based on openwrt so you can flash the sysupgrade
image via the vendor GUI or using command line sysupgrade utility.
Make sure to not save configuration over reflash as uci settings
differ between versions.

Note on MAC addresses:

Even though the platform is capable to providing separate MAC addresses
to the interfaces vendor firmware does not seem to take advantage of
that. It appears that there is only single unique pre-programmed
address in the art partition and vendor firmware uses that for
every interface (eth0/eth1/wlan0). Similar behaviour has also been
implemented in this patch.

Note on GPIOs:

In vendor firmware the gpio controlling mini pci-e slot is named
3gcontrol while it actually controls power supply to the entire mini
pci-e slot. Therefore a more descriptive name (minipcie) was chosen.
Also during development of this patch it became apparent that the
polarity of the signal is actually active low rather than active high
that can be found in vendor firmware.

Acknowledgements:

This patch is based on earlier work[1] done by Kyson Lok. Since the
initial mailing-list submission the patch has been modified to comply
with current openwrt naming schemes and dts conventions.

[1] http://lists.openwrt.org/pipermail/openwrt-devel/2018-September/019576.html

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
2020-07-03 20:48:05 +02:00
John Audia
472f5b1474 ipq806x: refresh config
Based on "make kernel_menuconfig CONFIG_TARGET=generic" and 5.4.49

CONFIG_LEDS_TRIGGER_DISK has been removed by the refresh and added
back manually in order to not revert f93fcf8923 ("ipq806x: enable
disk-activity LED trigger").

Signed-off-by: John Audia <graysky@archlinux.us>
[extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 20:38:06 +02:00
Sungbo Eo
91472dc2ce kirkwood: support for button in Pogoplug V4
Pogoplug V4 has a reset button on a GPIO pin.
To use it, kmod-gpio-button-hotplug package needs to be installed.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-03 19:48:51 +02:00
Adrian Schmutzler
b123ffdf6e ath79: drop redundant status for gpio target-wide
All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Adrian Schmutzler
dc1280ef65 ath79: enable gpio on ar933x by default
All other SoC DTSI files have gpio enabled by default, only
ar9330/ar9331 disable it by default, only to have it enabled again
afterwards for each individual device.

So, do not disable it in the first place, and drop all device-specific
status statements afterwards.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Leon M. George
a0bb356612 ath79: add support for Compex WPJ344
Specifications:

SoC: AR9344
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 48V IEEE 802.3af/at - 24V passive optional
USB 2.0 header

Installation:

To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj344-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '6A08':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj344-16m-squashfs-cpximg-6a08.bin

MAC addresses:

<&uboot 0x2e010>  *:99  (label)
<&uboot 0x2e018>  *:9a
<&uboot 0x2e020>  *:9b
<&uboot 0x2e028>  *:9c

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[minor commit message adjustments, drop gpio in DTS, DTS style fixes,
sorting, drop unused cpximg recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Sungbo Eo
736995ce19 ath79: rearrange nand node by register address
All other nodes in the DTS are placed in order of address space. Harmonize
the nand nodes as well.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-02 21:34:37 +02:00
Rowan Border
33fae8421e ramips: add support for TP-Link RE220 v2
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.

Specifications

MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.

Web Interface Installation

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Signed-off-by: Rowan Border <rowanjborder@gmail.com>
2020-06-30 17:23:32 +02:00
Kevin Darbyshire-Bryant
d59dc14515 kernel: cake: backport upstream tweaks & fixes
From upstream:
b8392808eb3f sch_cake: add RFC 8622 LE PHB support to CAKE diffserv handling
3f608f0c4136 sch_cake: fix a few style nits
8c95eca0bb8c sch_cake: don't call diffserv parsing code when it is not needed
9208d2863ac6 sch_cake: don't try to reallocate or unshare skb unconditionally

From netdev not yet accepted:
sch_cake: fix IP protocol handling in the presence of VLAN tags

The VLAN tag handling is actually wider than just cake so upstream are
working out how to fix it generically.  We fix it here just for cake.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-30 16:09:18 +01:00
Kevin Darbyshire-Bryant
77cd8f64ca kernel: cake: backport unused var patch to 5.4
This was backported to 4.19 and I clearly expected it to land in 5.4 but
it didn't (5.5) so backport it to 5.4 for consistency.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-30 09:34:24 +01:00
Kevin Darbyshire-Bryant
4ca4c94267 kernel: cake: skb hash backport to 419
Commit 7b4877c204 backported to 5.4 only,
backport to 4.19 as well.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-30 09:34:17 +01:00
Kevin Darbyshire-Bryant
3fda01a51e kernel: cake: renumber backport patches
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-30 09:34:06 +01:00
David Bauer
5667ccbf16 ramips: remove duplicate MAC assignment case
Cudy WR1000 and Wavlink WL-WN577A2 store WAN as well as label MAC address
at the same position in flash.

Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 15:55:55 +02:00
David Bauer
1ba0466d43 package: add ravpower-mcu package
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:04 +02:00
David Bauer
e959048c12 ramips: add support for RAVPower RP-WD009
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.

Hardware
--------
CPU:   MediaTek MT7628AN
RAM:   64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN:  MediaTek MT7628AN 2T2R b/g/n
       MediaTek MT7610E  1T1R n/ac
ETH:   1x FastEthernet
SD:    SD Card slot
USB:   USB 2.0

Custom PMIC on the I2C bus (address 0x0a).

Installation
------------

1. Press and hold down the reset button.

2. Power up the Device. Keep pressing the reset button for 10
   more seconds until the Globe LED lights up.

3. Attach your Computer to the Ethernet port. Assign yourself the
   address 10.10.10.1/24.

4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
   factory image.

5. The flashing will take around 1 minute. The device will reboot
   automatically into OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:01 +02:00
David Bauer
f49063ba92 ath79: replace custom uImageArcher generation
The replaces the custom uImageArcher build step with the generic uImage
build step. The only different between these two is the difference in
the generated name.

Tested on: TP-Link Archer C59 v1

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 01:08:09 +02:00
Lars Wessels
dbaf0d20bb ramips: add support for WAVLINK WL-WN577A2
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):

Device specifications:

- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps (Ralink RT3050)
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER
- Buttons: Reset, WPS
- Small sliding power switch

Flashing instructions (U-boot):

- Configure a TFTP server on your PC/Laptop and set its IP
  to 192.168.10.100

- Rename the OpenWrt image to firmware.bin and place it in the
  root folder of the TFTP server

- Power off (using the small sliding power switch on the left
  side) the device and connect an ethernet cable from its LAN
  or WAN port to your PC/Laptop

- Press the WPS button (and keep it pressed)

- Power on the device (using the small power switch)

- After a few seconds, when the WAN/LAN LED stops blinking
  very fast, release the WPS button

- Flashing OpenWrt takes less than a minute, system will
  reboot automatically

- After reboot the WPS LED will indicate the current OpenWrt
  running status

Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 01:08:01 +02:00
Adrian Schmutzler
5234593462 mvebu: move definition of factory.img out of Device/Default
The Device/Default definition in mvebu defines an IMAGE/factory.img
which is not included in IMAGES, and only used twice in the
individual definitions. Move it out of the default definition
to keep it closer to the reassignment of IMAGES and make it more
consistent with respect to other values of IMAGE/factory.img

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 14:07:57 +02:00
Adrian Schmutzler
0127de9547 ipq806x: set IMAGES in Device/Default definition
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.

Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 14:07:50 +02:00
Adrian Schmutzler
e8afeaabc0 ipq40xx: set IMAGES in Device/Default definition
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.

Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 14:07:43 +02:00
Adrian Schmutzler
8819faff47 ath79: do not build TP-Link tiny images by default
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.

Disable these images for the buildbots and prevent useless builds.

Note that these devices still build fine with default settings,
even for kernel 5.4.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:33:44 +02:00
Adrian Schmutzler
89bb4ee450 mvebu: remove non-existant board name solidrun,clearfog-a1
In 02_network, the board name solidrun,clearfog-a1 is used in a
case, but it does not seem to be used/exist anywhere else in OpenWrt.

The valid strings are:
- solidrun,clearfog-pro-a1
- solidrun,clearfog-base-a1

Fixes: 12795ec9f1 ("mvebu: split interface configuration for
clearfog pro and base")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:32:29 +02:00
Leon M. George
9f261e36de ath79: build Compex WPJ531 cpximg files
Generate additional images that are compatible to the cpximg loader.
The cpximg loader can be started either by holding the reset button during
power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '7A04':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin

These files can also be used with the sysupgrade utility in stock images (add
SSH key in luci for root access).

Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix sorting of definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:26:39 +02:00
Leon M. George
e10dd48360 ath79: add support for Compex WPJ531 (16M)
Specifications:

SoC: QCA9531
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 100MBit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V - 48V IEEE 802.3af optional
USB 2.0 header

Installation:

To install, start a tftp server in bin/targets/ath79/generic/ and use the
u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj531-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add SSH key
in luci for root access).

Another way is to hold the reset button during power up or running 'cpximg' in
the u-boot prompt.
Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1
will accept the image appropriate for the board revision that is etched on the
board.

For example, if the board is labelled '7A04':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin

MAC addresses:

<&uboot 0x2e010>  *:cb  (label)
<&uboot 0x2e018>  *:cc
<&uboot 0x2e020>  *:cd
<&uboot 0x2e028>  *:ce

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message facelift, fix rssileds, add led aliases]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:26:39 +02:00
Jan Hoffmann
b1d5ab1a69 ramips: add support for NETGEAR WAC124
The WAC124 hardware appears to be identical to R6260/R6350/R6850.

SoC:   MediaTek MT7621AT
RAM:   128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI:  MediaTek MT7603 bgn 2T2R
       MediaTek MT7615 nac 4T4R
ETH:   SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB:   1x USB 2.0
BTN:   Reset, WPS
LED:   Power, Internet, WiFi, USB (all green)

Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2020-06-27 00:33:29 +02:00
Alex Lewontin
bd49f2c984 ramips: add support for Netgear R6080
This adds support for the Netgear R6080, aka Netgear AC1000.

The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.

Specification:

SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB

Installation:

Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-27 00:29:45 +02:00
Hauke Mehrtens
4c3b81b75d ath79: Fix ubnt_edgeswitch-8xp DEVICE_PACKAGES
switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio
instead.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Tobias Schramm <tobleminer@gmail.com>
2020-06-27 00:19:13 +02:00
Daniel González Cabanelas
0cca96284a mvebu: LS421DE: dts file improvements
- Delete useless HDD presence inputs: they aren't buttons, and probably
  they are outputs in the stock firmware.
- Change the Function Button keycode: the current one isn't mapped by
  the kernel module.
- Use the recommended property names for the ethernet stuff.
- Add missing i2c pinmux.
- Minor cosmetic changes.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-27 00:19:13 +02:00
Aleksander Jan Bajkowski
58a6f06978 lantiq: remove unused PHY drivers on xrx200
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fb.

Save 20.3 kB flash memory.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-06-27 00:19:13 +02:00
Qin Wei
cd6515c2e8 ramips: fix sd polling
This is fixed in 18.06, it appears again in 19.07.
Currently mt7628 sdcard driver do not support polling mode which is for
the device do not have card-detect pin to detect sd card insert. Without
this patch, device will not detect sdcard is inserted. This patch is a
fix of that.

Signed-off-by: Qin Wei <support@vocore.io>
2020-06-27 00:19:13 +02:00
Rogan Dawes
9c85153b87 sunxi: add text referencing Allwinner H3 and H5 CPUs
This makes it a little easier to figure out which options to choose.

Signed-off-by: Rogan Dawes <rogan@dawes.za.net>
2020-06-27 00:19:13 +02:00
Gregory L. Dietsche
f3cb1636ab x86: Support Intel 10 Gigabit Ethernet Cards
Support Intel 10 Gigabit Ethernet Cards in x86/64 images by default.
This ensures that systems with cards such as the Intel x520 will work properly.

Signed-off-by: Gregory L. Dietsche <Gregory.Dietsche@cuw.edu>
2020-06-27 00:19:05 +02:00
Florian Eckert
5596452cd4 target/hack-5.4: platform/x86/pcengines: revert led simswich compromise
With this change the LED subsystem is abused in the kernel to switch the
simswap. This change will be reverted, so we could use again the gpio
subsystem.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2020-06-26 20:54:53 +02:00
Florian Eckert
f3c5c09e5a kernel: add pcengines-apu2 module description
Add a module description for the new pcengnies-apu2 device driver.
This driver supports the front button and LEDs on the PC Engines
APUv2/APUv3 boards.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2020-06-26 20:54:53 +02:00
Adrian Schmutzler
635f111148 ath79: drop and consolidate redundant chosen/bootargs
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.

The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi

Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-25 23:09:05 +02:00
Adrian Schmutzler
54b19e213a ramips: drop redundant chosen/bootargs
chosen/bootargs are defined to the same value in device DTS files
that is already set in the SoC DTSI. Remove the redundant definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-25 22:33:36 +02:00
Natalie Kagelmacher
8ff631feff ath79: add support for AVM FRITZ!WLAN Repeater DVB-C
This commit adds support for the AVM FRITZ!WLAN Repeater DVB-C

SOC:   Qualcomm Atheros QCA9556
RAM:   64 MiB
FLASH: 16 MB SPI-NOR
WLAN:  QCA9556 3T3R 2.4 GHZ b/g/n and
       QCA9880 3T3R 5 GHz n/ac
ETH:   Atheros AR8033 1000 Base-T
DVB-C: EM28174 with MaxLinear MXL251 tuner
BTN:   WPS Button
LED:   Power, WLAN, TV, RSSI0-4

Tested and working:
 - Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s)
 - 2.4 GHz Wi-Fi (correct MAC)
 - 5 GHz Wi-Fi (correct MAC)
 - WPS Button (tested using wifitoggle)
 - LEDs
 - Installation via EVA bootloader (FTP recovery)
 - OpenWrt sysupgrade (both CLI and LuCI)
 - Download of "urlader" (mtd0)

Not working:
 - Internal USB
 - DVB-C em28174+MxL251 (depends on internal USB)

Installation via EVA bootloader (FTP recovery):
Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device,
connect to 192.168.178.1 through FTP and sign in with adam2/adam2:

ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1

Wait for "Transfer complete" together with the transfer details.
Wait two minutes to make sure flash is complete (just to be safe).

Then restart the device (power off and on) to boot into OpenWrt.
Revert your NIC settings to reach OpenWrt at 192.168.1.1

Signed-off-by: Natalie Kagelmacher <nataliek@pm.me>
[fixed sorting - removed change to other board -
prettified commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-25 02:35:35 +02:00
Edward Matijevic
6da3194127 bcm47xx: add support for NETGEAR R6200 V1
This patch adds supports for the NETGEAR R6200 V1
This device is mainlined in Linux as of 5.4

Specification:
   - SOC: Broadcom BCM4718A1 (480 MHz)
   - Flash: 16MB (Macronix MX25L128)
   - RAM: 128MB DDR2
   - SWITCH: BCM53125
   - Ethernet: 5x GE (1 WAN + 4 LAN, Inverted order)
   - WLAN 2.4G: In SOC
   - WLAN 5GHz: miniPCIe card, BCM4352 (ID: 4360)
   - USB: 1x USB 2.0 port (Type A)
   - Buttons: Reset, WLAN, WPS
   - LED: Amber for Power, others need a workaround
   - UART: 1x UART on PCB

LED Issues: They are controlled by a 74HC164 via bit banging(GPIO 6/7)

Firmware Install Instructions
=============================
Using the device specific .chk, use that file to perform
a normal device upgrade in the OEM admin page.

Signed-off-by: Edward Matijevic <motolav@gmail.com>
2020-06-24 00:17:49 +02:00
Alex Lewontin
2e47a05d87 ramips: clean up Netgear R6120 code formatting
This commit performs minor janitorial work to clean up some code
formatting for the Netgear R6120.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2020-06-23 21:56:44 +02:00
Alex Lewontin
888afe7c69 ramips: move Netgear R6120 LED trigger to DTS
This moves the trigger for the Netgear R6120's wlan2g_green LED from
base-files/etc/board.d/01_leds to the device-tree file.

This has been applied to R6120 based on findings for the very similar
Netgear R6080.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[merge case in 01_leds, slightly adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-23 21:53:22 +02:00
Adrian Schmutzler
3c20bb0644 mvebu: consolidate DTS files
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (armada-3720-uDPU.dts), which is only present
for 4.19, as it has been upstreamed before 5.4.

Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory, only keeping
the named exception to files-4.19.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-23 21:02:40 +02:00
Adrian Schmutzler
fa6d53261a ipq40xx: consolidate DTS files
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (qcom-ipq4018-emr3500.dts), which is only
present for 5.4.

Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory.

If there ever was a new kernel with substantial DTS changes, a
new folder would need to be introduced anyway and could easily be
done.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-23 21:02:26 +02:00
Jose Olivera
d0e8b8310f mvebu: fix default EU regdomain for Linksys WRT AC devices
The mwlwifi driver sets the default country code for EU (fi-
rmware region code 0x30) certified devices to FR (France),
not DE (Germany). Whilst this is a trivial fix, novice users
may not know how mwlwifi negatively reacts to a non-matching
country code and may leave the setting alone. Especially si-
nce it is under the advanced settings section in LuCI.

Relevant mwlwifi driver code:
0a550312dd

The mwlwifi driver readme states "Please don't change country
code and let mwlwifi set it for you." However, OpenWrt's current
behaviour does not adhere to this with its default, 'just flashed
from factory' setting for EU devices.

Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-23 15:01:17 +02:00
Petr Štetiar
472b8fc91b armvirt,x86: fix build breakage of crypto ccp module
Upstream in commit f9f8f0c24203 ("crypto: ccp -- don't "select"
CONFIG_DMADEVICES") removed dependency on CONFIG_DMADEVICES symbol which
leads to build breakage of ccp crypto module, so fix this by adding that
symbol back in the kernel config.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-23 09:29:00 +02:00
Daniel González Cabanelas
3f27a6e640 bcm63xx: AV4202N: add missing PCI pinmux
The ADB P.DG AV4202N device has a wifi chipset connected via PCI. But the
PCI pinmux is missing and without it the wifi won't work properly.

Add the pinctrl_pci to enable the missing PCI pins for this device.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-22 15:43:41 +02:00
Petr Štetiar
e44e60b290 kernel: bump 5.4 to 5.4.48
Resolved merge conflict in the following patches:

 layerscape: 701-net-0213-dpaa2-eth-Add-CEETM-qdisc-support.patch
 ramips: 0013-owrt-hack-fix-mt7688-cache-issue.patch

Refreshed patches, removed upstreamed patch:

 bcm63xx: 020-v5.8-mtd-rawnand-brcmnand-fix-hamming-oob-layout.patch

Run tested: qemu-x86-64
Build tested: x86/64

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-22 12:51:22 +02:00
Petr Štetiar
ceeece9ffa ath79: image: fix initramfs for safeloader devices
Currently it's not possible to tftpboot initramfs image on archer-c7-v5
as the image contains tplink-v1-header which leads to:

 ath> bootm
 ## Booting image at 81000000 ...
 Bad Magic Number

as U-Boot expects uImage wrapped image. This is caused by following
inheritance issue:

  define Device/Init
    KERNEL_INITRAMFS = $$(KERNEL)

  define Device/tplink-v1
    KERNEL := kernel-bin | append-dtb | lzma
    KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | tplink-v1-header

  define Device/tplink-safeloader
    $(Device/tplink-v1)

  define Device/tplink-safeloader-uimage
    $(Device/tplink-safeloader)
    KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma

  define Device/tplink_archer-c7-v5
    $(Device/tplink-safeloader-uimage)

where tplink-v1 defines KERNEL_INITRAMFS with tplink-v1-header and it's
then used by all devices inheriting from tplink-safeloader. Fix this by
overriding KERNEL_INITRAMFS to KERNEL variable again.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-22 12:51:22 +02:00
Adrian Schmutzler
340de1d154 lantiq: fritz7312: set maximum speed to 100 mbit on 5.4
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.

The previous patch in 36f628910b was only applied to the 4.19 file,
so let's just make it consistent with this patch.

Cc: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-21 21:30:36 +02:00
Lech Perczak
708c6772f6 ath79: fix input type for TP-Link TL-WR902AC v1 mode switch
Inputs assigned to "mode select" switch on the side of the device
were missing linux,input-type property.
This would cause them do incorrectly generate EV_KEY events.
Fix this by setting the linux,input-type = <EV_SW> property on them.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2020-06-21 21:29:51 +02:00
INAGAKI Hiroshi
3a8d65010d ramips: add support for ELECOM WRC-2533GST2
ELECOM WRC-2533GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 256 MiB
- Flash		: SPI-NOR 32 MiB
- WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from ethernet port side
  - 57600n8
- Power		: 12VDC, 1.5A

Flash instruction using factory image:

1. Boot WRC-2533GST2 normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-06-21 20:56:42 +02:00
INAGAKI Hiroshi
39f2f9b1bf ramips: add MT7615 wireless support for ELECOM WRC-GST devices
ELECOM WRC-1900GST and WRC-2533GST have two MT7615 chips for 2.4/5 GHz
wireless.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
2020-06-21 20:52:30 +02:00
INAGAKI Hiroshi
b5ae70d053 ramips: increase SPI frequency for ELECOM WRC-GST devices
Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST
to 40 MHz by updating the common DTSI file.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-21 20:48:46 +02:00
INAGAKI Hiroshi
5aae0c7862 ramips: add label-mac-device for ELECOM WRC-GST devices
Update the dtsi for ELECOM WRC-1900GST and WRC-2533GST to add
label-mac-device alias.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-21 20:48:17 +02:00
Andrew Cameron
d93da0d016 ath79: add support for TP-Link CPE610 v2
TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - 560/450/225 MHz (CPU/DDR/AHB)
 - 1x 10/100 Mbps Ethernet
 - 64 MB of DDR2 RAM
 - 8 MB of SPI-NOR Flash
 - 23dBi high-gain directional 2×2 MIMO antenna and a
   dedicated metal reflector
 - Power, LAN, WLAN5G green LEDs
 - 3x green RSSI LEDs

Flashing instructions:
 Flash factory image through stock firmware WEB UI
 or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2020-06-20 13:03:39 +02:00
Adrian Schmutzler
9a477b833a ath79: add support for TP-Link TL-WA801ND v3/v4
This ports support for these devices from ar71xx.

Specification:

- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: v3: 560 MHz, v4: 650 MHz
- Flash: 4096 KiB
- RAM: 32 MiB
- Ethernet: 1 port @ 100M
- Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn

In contrast to the implementation in ar71xx (reset and WiFi button),
the device actually features reset and WPS buttons.

Flashing instructions:

Upload the ...-factory.bin file via OEM web interface.

TFTP Recovery:

1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to
   wa801ndv3_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

TFTP recovery has only been tested with v3, and the Wiki states
that the procedure won't work for v4, which cannot be verified
or falsified at the moment.

Tested by Tim Ward (see forum):
https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-19 15:50:29 +02:00
Daniel González Cabanelas
583b3e4025 bcm63xx: DGND3700v1: fix port order
Fix the switch LAN labels for the DGND3700v1/DGND3800B router,
the order is reversed.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[cut out of bigger patch, adjust commit title/message accordingly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-19 13:54:16 +02:00
Daniel González Cabanelas
2c3bdef4bd bcm63xx: HG622: enable LAN LEDs
The Huawei Echolife HG622 has hardware controlled LAN LEDs.

Add the ephy led pinctrl to let the router show LAN activity on these
LEDs.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-19 13:43:42 +02:00
Adrian Schmutzler
be56b29707 ath79: set &eth1 status for TP-Link CPE devices in parent DTSI
The status is set to "okay" for all devices on ar9344, so just move
this to the parent DTSI.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-18 22:34:09 +02:00
Hannu Nyman
9c16c46e58 ath79: define CONFIG_MFD_RB4XX_CPLD to fix build breakage
Define the kernel config symbol CONFIG_MFD_RB4XX_CPLD=n
to fix build breakage on non-mikrotik targets.

The driver was added for all ath79, but the symbol was only
defined for mikrotik subtarget.

Fixes: fa70b3a4bb ("ath79: add Mikrotik rb4xx series drivers")

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[rearrange commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-17 19:50:54 +02:00
Adrian Schmutzler
ef9cee4980 lantiq: drop "CONFIG_HZ_100 is not set"
CONFIG_HZ_100 is not set to "y" in generic config anymore since
3a761c90af ("treewide: Don't diverge from upstream default HZ
settings on 4.19"), so we don't need to disable it anymore either.

This was the only remaining case in the entire tree.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-17 14:26:09 +02:00
Aleksander Jan Bajkowski
27724c2f54 lantiq: switch to 5.4
Runtime tested on BT Home Hub 5A and D-Link DWR-966.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-06-17 00:50:45 +02:00
Petr Štetiar
90f930e0c2 kernel: bump 5.4 to 5.4.46
Refreshed patches.

Run tested: qemu-x86-64, wrt3200acm
Build tested: x86/64, imx6, mvebu/cortexa9, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-16 23:36:26 +02:00
Petr Štetiar
014c101e0b mvebu: fix bootloader kernel commandline mangling
Currently I'm unable to boot initramfs image with `console=ttyS0,115200`
kernel commandline as the kernel commandline mangling resets kernel
commandline if there is no `root=` option provided, efectively clearing
whatever I pass to the kernel, making the `root=` option mandatory.

So if the kernel commandline mangling is not appropriate just leave the
kernel commandline as it is.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-16 23:36:26 +02:00
Sungbo Eo
c4037a5b9e mediatek: mt7623: refresh kernel 5.4 config
By running make kernel_oldconfig and selecting relevant options.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-06-16 15:54:58 +02:00
Daniel González Cabanelas
e3eaf52ba3 bcm63xx: use the generic nand upgrade on Sercomm devices
The Sercomm devices don't need the jffs2 cleanmarkers for the kernel
partition. With the stock firmware they are only added when the
bootloader partition is upgraded.

Furthermore, on the Sercomm H500-s, the specific cfe_jffs2_upgrade_tar
function causes OOB corruption. As a result of this, combined with the
nature of the mtdsplit driver, the upgrade procedure ends in a bricked
device.

Use the generic nand_do_upgrade provided by the OpenWrt common functions.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-16 14:55:02 +02:00
Adrian Schmutzler
636b62e8e2 mediatek: fix IPv4-only corner case and commit in 99-net-ps
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.

Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.

Fix that by adding the setup there as well.

While at it, limit the uci commit to the network config file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-16 14:46:42 +02:00
Adrian Schmutzler
866ad46662 ath79: add support for the TP-Link WBS210 v1
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-16 14:42:15 +02:00
Adrian Schmutzler
48c1fdd046 treewide: drop shebang from non-executable target files
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.

While at it, fix the executable flag on a few of these files.

This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-16 14:26:33 +02:00
Christopher Hill
b7a8a54542 ath79: add support for MikroTik RouterBOARD 493G (rb4xx series)
This patch adds support for the MikroTik RouterBOARD RB493G, ported
from the ar71xx target.

See https://routerboard.com/RB493G for details

Specification:
- SoC Qualcomm Atheros AR7161
- RAM: 256 MiB
- Storage: 128MiB NAND
- Ethernet: 9x 1000/100/10 Mbps
- USB 1x 2.0 / 1.0 type A
- PCIe: 3x Mini slot
- MicroSD slot

Working:
- Board/system detection
- Ethernet
- SPI
- NAND
- LEDs
- USB
- Sysupgrade

Enabled (but untested due to lack of hardware):
- PCIe - ath79_pci_irq struct has the slot/pin/IRQ mappings if needed

Installation methods:
- tftp boot initramfs image, scp then flash via "sysupgrade -n"
- nand boot existing OpenWrt, scp then flash via "sysupgrade -n"

Notes:
- initramfs image will not work if uncompressed image size over ~8.5Mb
- The "rb4xx" drivers have been enabled

Signed-off-by: Christopher Hill <ch6574@gmail.com>
2020-06-15 21:16:18 +02:00
Christopher Hill
fa70b3a4bb ath79: add Mikrotik rb4xx series drivers
This adds 3 Mikrotik rb4xx series drivers as follows:

rb4xx-cpld: This is in the mfd subsystem, and is the parent CPLD device
that interfaces between the SoC SPI bus and its two children below.
rb4xx-gpio: This is the GPIO expander.
rb4xx-nand: This is the NAND driver.

The history of this code comes in three phases.

1. The first is a May 2015 attempt to push the equivalient ar71xx rb4xx
drivers upstream. See https://lore.kernel.org/patchwork/patch/940880/.

Module-author: Gabor Juhos <juhosg@openwrt.org>
Module-author: Imre Kaloz <kaloz@openwrt.org>
Module-author: Bert Vermeulen <bert@biot.com>

2. Next several ar71xx patches were applied bringing the code current.

commit 7bbf4117c6
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

commit af79fdbe4a
commit 889272d92d
commit e21cb649a2
commit 7c09fa4a74
Signed-off-by: Felix Fietkau <nbd@nbd.name>

3. Finally a heavy refactor to split the driver into the three new
subsystems, and updated to work with the device tree configuration, plus
updates and review feedback incorporated

Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Christopher Hill <ch6574@gmail.com>
2020-06-15 21:16:18 +02:00
Christopher Hill
344e75eb2b ath79: patch upstream Mikrotik rb4xx-spi driver to be device tree aware
Backport upstream patches that make drivers/spi/spi-rb4xx.c device tree
aware, plus a null pointer fix.

Signed-off-by: Christopher Hill <ch6574@gmail.com>
2020-06-15 21:16:18 +02:00
Daniel González Cabanelas
d64d5ed142 bcm63xx: a226m-fwb: fix linux partition offset
The Pirelli A226M-FWB has a wrong linux partition offset, caused
by a copy-paste error. As of result of this, OpenWrt is currently
broken in this unit.

Fix it.

While at it, also use generic node names and fix the addresses
there as well.

Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout
specification")

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[also fix/update node names, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-15 20:59:10 +02:00
David Bauer
fa412c9354 ath79: ag71xx: don't warn on RGMII_RXID and RGMII_TXID
Currently, ag71xx will trigger a warning when TX xor RX-Delay modes are
enabled.

Handle them identical to the already implemented RGMII modes, as they
are only different for the attached PHY.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-15 20:41:06 +02:00
Adrian Schmutzler
03a0b7b7e5 ramips: fix IPv4-only corner case in 01_enable_packet_steering
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.

Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.

Fix that by adding the setup there as well.

Fixes: dfd62e575c ("ramips: enable packet steering by default on mt7621")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-15 00:04:35 +02:00
Pawel Dembicki
1461eabda3 Revert "kirkwood: disable image for Linksys EA3500 (Audi)"
This reverts commit d9ff499671.

At this moment kernel can be fitted in EA3500 image.

Tested by onefreeman (OpenWrt forum user)
Tested-by: Jacks <jack338c@gmail.com> (Github user @jack338c)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-06-14 21:16:20 +02:00
Pawel Dembicki
28f4ae2e4b kirkwood: refresh kernel config
It was made by running "make kernel_oldconfig".

Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-14 21:16:20 +02:00
Pawel Dembicki
987292b20a kirkwood: move ext4 support to modules
Ext4 support is built in kirkwood kernel.

This patch moves ext4 support to modules and enables it for devices
with SATA interface.

Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-14 21:16:20 +02:00
Pawel Dembicki
e53ec043ba kirkwood: move usb support to modules
USB support built in kernel isn't required for booting.
This patch move USB support to modules.

CONFIG_USB_STORAGE is removed because it can be found in kmod-usb-storage
and all usb support for this targed is moved to kmods.

Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310]
Tested-by: Alberto Bursi <bobafetthotmail@gmail.com> [nsa325, ea4500]
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[keep CONFIG_SCSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-14 21:16:20 +02:00
Pawel Dembicki
c5356d10c0 kirkwood: move mmc/sd features to modules
All devices are using nand images. Built-in MMC/SD modules are not needed
anymore.

Run tested: pogo v4

Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-06-14 21:16:20 +02:00
Pawel Dembicki
73c3ba23a4 kirkwood: move sata features to modules
All devices are using nand images. Built-in SATA modules are not needed
anymore.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[only move CONFIG_SATA_MV]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [pogo v4]
2020-06-14 21:16:20 +02:00
Pawel Dembicki
bbe7124945 kirkwood: move led triggers to dts
This patch moves led trigger settings from 01_leds file to dts.

Now "linux,default-trigger" property is used.

Tested-by: Alberto Bursi <bobafetthotmail@gmail.com> [nsa310,nsa325]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-06-14 21:16:20 +02:00
David Bauer
373f446049 ipq40xx: check kernel-size for NBG6617
The ZyXEL NBG6617 has a separate kernel partition which is 4MiB large.

Add the kernel size to validate the kernel won't be bigger than this
fixed limit.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-14 13:10:00 +02:00
David Bauer
5b50895a63 ipq40xx: add image size checks for several devices
This adds image size checks for various devies using an automatic
mtdsplit.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-14 13:09:59 +02:00
David Bauer
b8ed898f1b ipq40xx: use zImage for EX6100v2 and EX6150v2
The NETGEAR EX61500v2 and EX6150v2 U-Boot does not support booting LZMA
compressed images. Currently, they are using GZIP compressed kernels,
which results in ledd flash being available to the root and overlay
filesystems.

Using a zImage results in a smaller kernel and therefore increases
available space for rootfs and overlayfs.

Size reduced: ~1.1 MiB

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-13 16:57:53 +02:00
DENG Qingfang
752cee796d ipq40xx: disable DSA and Switchdev
ipq40xx is still using swconfig based switch management. This might
change in he future, however disable the DSA and Switchdev support for
now.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[rephrased commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-13 16:57:15 +02:00
Yen-Ting-Shen
3f61e5e1b9 ipq40xx: add support for EnGenius EMR3500
SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8072 (2 ports)
USB:     1 x 2.0 (Host controller in the SoC)
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET Button
LEDS:    White, Blue, Red, Orange

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMR3500. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
   (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img
4. Flash the firmware
   (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
   (IPQ40xx) # reset

Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[squashed update patch, updated to 5.4, dropped BOARD_NAME,
migrated to SOC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-06-13 14:38:03 +02:00
Sven Eckelmann
6785695056 ipq40xx: essedma: Disable TCP segmentation offload for IPv6
It was noticed that the the whole MAC can hang when transferring data from
one ar40xx port (WAN ports) to the CPU and from the CPU back to another
ar40xx port (LAN ports). The CPU was doing only NATing in that process.

Usually, the problem first starts with a simple data corruption:

  $ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null
  ...
  Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected.
  ...
  Read  error at byte 48807936/352321536 (Decryption has failed.). Retrying.

But after a short while, the whole MAC will stop to react. No traffic can
be transported anymore from the CPU port from/to the AR40xx PHY/switch and
the MAC has to be resetted.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: John Crispin <john@phrozen.org>
2020-06-13 14:38:03 +02:00
Adrian Schmutzler
5549b84388 ramips: drop useless label-mac-device for RouterBOARD 750Gr3
With the new driver, MAC addresses are not set up in DTS anymore,
and therefore label-mac-device will be useless there.

Setup is done properly in 02_network, so this just removes the
obsolete alias.

Fixes: 5e50515fa6 ("ramips/mt7621: mikrotik: don't use
mtd-mac-address in DTS")

Suggested-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-13 13:53:27 +02:00
Adrian Schmutzler
1226113fe2 bcm47xx: move device definitions to subfiles
With several subtargets, the image/Makefile becomes crowded after a
while. Many targets have moved their device definitions to $subtarget.mk
files to have them more organized, let's do this here as well.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-12 19:01:47 +02:00
J. Scott Heppler
feb55fd3ec ramips: fix port display for TRENDnet TEW-810DR
This updates the display port order for the TEW-810DR to be in line
with the DIR-810L. Both share the same board and pictures on the
vendors' pages indicate the same external numbering scheme as well.

Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[replace commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-12 18:10:37 +02:00
Pawel Dembicki
221d8a1c60 ramips: mt7621: add support for NETGEAR WAC104
NETGEAR WAC104 is an AP based on castrated R6220, without WAN
port and USB.

SoC: MediaTek MT7621ST
RAM: 128M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7612EN an+ac
MediaTek MT7603EN bgn
ETH: MediaTek MT7621ST (4x LAN)
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: 7x (3x GPIO controlled)

Installation:

Login to netgear webinterface and flash factory.img

Back to stock:

Use nmrpflash to revert stock image.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-06-12 14:13:32 +02:00
Stijn Tintel
cd09f26660 ath79: add support for D-Link DAP-2695-A1
Hardware:
* SoC: Qualcomm Atheros QCA9558
* RAM: 256MB
* Flash: 16MB SPI NOR
* Ethernet: 2x 10/100/1000 (1x 802.3at PoE-PD)
* WiFi 2.4GHz: Qualcomm Atheros QCA9558
* WiFi 5GHz: Qualcomm Ahteros QCA9880-2R4E
* LEDS: 1x 5GHz, 1x 2.4GHz, 1x LAN1(POE), 1x LAN2, 1x POWER
* Buttons: 1x RESET
* UART: 1x RJ45 RS-232 Console port

Installation via stock firmware:
* Install the factory image via the stock firmware web interface

Installation via bootloader Emergency Web Server:
* Connect your PC to the LAN1(PoE) port
* Configure your PC with IP address 192.168.0.90
* Open a serial console to the Console port (115200,8n1)
* Press "q" within 2s when "press 'q' to stop autoboot" appears
* Open http://192.168.0.50 in a browser
* Upload either the factory or the sysupgrade image
* Once you see "write image into flash...OK,dest addr=0x9f070000" you
  can power-cycle the device. Ignore "checksum bad" messages.

Setting the MAC addresses for the ethernet interfaces via
/etc/board.d/02_network adds the following snippets to
/etc/config/network:

config device 'lan_eth0_1_dev'
        option name 'eth0.1'
        option macaddr 'xx:xx:xx:xx:xx:xx'

config device 'wan_eth1_2_dev'
        option name 'eth1.2'
        option macaddr 'xx:xx:xx:xx:xx:xx'

This would result in the proper MAC addresses being set for the VLAN
subinterfaces, but the parent interfaces would still have a random MAC
address. Using untagged VLANs could solve this, but would still leave
those extra snippets in /etc/config/network, and then the device VLAN
setup would differ from the one used in ar71xx. Therefore, the MAC
addresses of the ethernet interfaces are being set via preinit instead.

The bdcfg partition contains 4 MAC address labels:
 - lanmac
 - wanmac
 - wlanmac
 - wlanmac_a

The first 3 all contain the same MAC address, which is also the one on
the label.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 19:44:45 +03:00
Stijn Tintel
7e287ff89d ath79: enable wrgg MTD splitter
This is required for the D-Link DAP-2695-A1.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-06-11 19:44:36 +03:00
INAGAKI Hiroshi
8f3b176e86 kernel: rtl8367b: fix external interface modes
The interface mode number of RGMII_33V is 7 on RTL8367, but it's 9 on
RTL8367B.

the external interface modes for RTL8367 are follows:

- 0, Disabled
- 1, RGMII
- 2, MII_MAC
- 3, MII_PHY
- 4, TMII_MAC
- 5, TMII_PHY
- 6, GMII
- 7, RGMII_33V

the external interface modes for RTL8367B are follows:

- 0, Disabled
- 1, RGMII
- 2, MII_MAC
- 3, MII_PHY
- 4, TMII_MAC
- 5, TMII_PHY
- 6, GMII
- 7, RMII_MAC
- 8, RMII_PHY
- 9, RGMII_33V

But the driver in U-Boot of RT-N56U GPL tar blocks using RGMII_33V (9)
mode and it seems to be unsupported on RTL8367B, so drop it from
switch-case in rtl8367b_extif_set_mode.

ref (RTL8367):

- TL-WR2453ND v1

ref (RTL8367B):

- ASUS RT-N56U
- TP-Link Archer C2 v1

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-06-11 21:50:01 +08:00
Adrian Schmutzler
efde716d14 ramips: fix port display for D-Link DIR-810L
The port order displayed in LuCI is currently inverted for this
devices:

LuCI - Device
LAN1 - LAN4
LAN2 - LAN3
LAN3 - LAN2
LAN4 - LAN1

Fix it.

Strangely, the owner of a TRENDnet TEW-810DR reports that the
initial port order is correct, while both devices share the
same board and look similar from the outside. Since I cannot
investigate this without having any of the devices, this does
only touch the DIR-810L for now.

While at it, also merge in the case for zbtlink,zbt-we2026, as
the display port specified for WAN there won't have any effect
anyway.

Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 10:21:17 +02:00
Álvaro Fernández Rojas
ce33ef997c bcm63xx: switch to upstream NAND patches
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-11 09:07:04 +02:00
Adrian Schmutzler
e6d4744f9a ramips: fix WAN LED for D-Link DIR-810L/TRENDnet TEW-810DR
The WAN LED on DIR-810L was actually blinking on LAN1 port
activity. This has already been improved for the TEW-810DR, where
the GPIO has been set up explicitly rather than having it controlled
by the switch.

This patch also applies this setup to the DIR-810L.

In addition, the trigger in 01_leds is set up with
ucidef_set_led_switch for both devices now, so state changes should
be displayed correctly as well.

Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [DIR-810L]
Tested-by: J. Scott Heppler <shep971@centurylink.net> [TEW-810DR]
2020-06-11 01:51:34 +02:00
Adrian Schmutzler
11db48f89a apm821xx: move device definitions to subfiles
With several subtargets, the image/Makefile becomes crowded after a
while. Many targets have moved their device definitions to $subtarget.mk
files to have them more organized, let's do this here as well.

While at it, also move subtarget-specific build recipes.

Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
2020-06-11 01:44:13 +02:00
Adrian Schmutzler
bb39fea11a treewide: simplify inclusion of subtarget image files
Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.

This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.

For sunxi, this includes a trivial rename of the subtarget image
Makefiles.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00
Renaud Lepage
108df3eabb ath79: add support for the Netgear WNDRMAC v1
The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2

Specifications
==============
* SoC: Atheros AR7161
* RAM: 64mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1)

Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.

After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v1.

Please use the `sysupgrade` variant for subsequent flashes.

Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3700 page on openwrt.org for details.

https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery

Signed-off-by: Renaud Lepage <root@cybikbase.com>
[update DTSI include name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00
Renaud Lepage
7f297e740b ath79: add support for the Netgear WNDRMAC v2
The Netgear WNDRMAC v2 is a hardware variant of the Netgear WNDR3800

Specifications
==============
* SoC: Atheros AR7161
* RAM: 128mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Serial console: Yes, 115200 / 8N1 (JTAG)
* USB: 1x2.0
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v2)

Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.

After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v2.

Please use the `sysupgrade` variant for subsequent flashes.

Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3800 page on openwrt.org for details.

https://openwrt.org/toh/netgear/wndr3800#recovery_flash_in_failsafe_mode

Signed-off-by: Renaud Lepage <root@cybikbase.com>
[do not add device to uboot-envtools, update DTSI name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00
Adrian Schmutzler
bc75954cca ath79: rename DTSI for Netgear WNDR devices based on ar7161
This renames the DTSI for Netgear WNDR devices based on ar7161 to
indicate that the file is not limited to WNDR3700 models.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00
Adrian Schmutzler
2c198ea162 ramips: limit uci commit to the changed config file
Since 01_enable_packet_steering only touches the network config,
limit the uci commit to this as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:43:41 +02:00
Adrian Schmutzler
338c64937f ramips: use amber LED for boot/failsafe on Netgear EX3700/EX6130
According to the manual, the amber power LED is used to indicate boot,
while the green LED is meant to indicate a running system.

While at it, also adjust the DT node names for all LEDs.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:41:43 +02:00
Adrian Schmutzler
fbb46b7bcc ramips: add support for Netgear EX6120
Specifications:
* SoC: MT7620A
* CPU: 580 MHz
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The device is identical to the EX6130 except
for the mains socket and the hardware ID.

Installation:
The -factory images can be flashed from the
device's web interface or via nmrpflash.

Notes:
MAC addresses were set up based on the EX6130 setup.

This is based on prior work of Adam Serbinski and Mathias Buchwald.

Tested by Mathias Buchwald.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:41:43 +02:00
Felix Fietkau
69f6fc7b15 ramips: add mt7621 ethernet driver improvements
- Speed up MDIO bus access
- Improve performance on tx completion

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-06-10 16:17:12 +02:00
Felix Fietkau
2c82862068 kernel: backport upstream DSA GRO support
Should improve performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-06-10 16:17:12 +02:00
Felix Fietkau
dfd62e575c ramips: enable packet steering by default on mt7621
It provides a significant performance boost, especially with flow offloading
enabled

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-06-10 16:17:12 +02:00
Christian Lamparter
61307544d1 ath79: wndr3700 series: fix wifi range & throughput
This patch adds ar71xx's GPIO setup for the 2.4GHz and 5GHz antennae
demultiplexer:

| 158         /* 2.4 GHz uses the first fixed antenna group (1, 0, 1, 0) */
| 159         ap9x_pci_setup_wmac_gpio(0, (0xf << 6), (0xa << 6));
| 160
| 161         /* 5 GHz uses the second fixed antenna group (0, 1, 1, 0) */
| 162         ap9x_pci_setup_wmac_gpio(1, (0xf << 6), (0x6 << 6));

This should restore the range and throughput of the 2.4GHz radio
on all the derived wndr3700 variants and versions with the AR7161 SoC.
A special case is the 5GHz radio. The original wndr3700(v1) will
benefit from this change. However the wndr3700v2 and later revisions
were unaffected by the missing bits, as there is no demultiplexer
present in the later designs.

This patch uses gpio-hogs within the device-tree for all
wndr3700/wndr3800/wndrmac variants.

Notes:

Based on the PCB pictures, the WNDR3700(v1) really had eight
independent antennae. Four antennae for each radio and all of
those were printed on the circut board.

The WNDR3700v2 and later have just six antennae. Four of those
are printed on the circuit board and serve the 2.4GHz radio.
Whereas the remaining two are special 5GHz Rayspan Patch Antennae
which are directly connected to the 5GHz radio.

Hannu Nyman dug pretty deep and unearthed a treasure of information
regarding the history of how these values came to be in the OpenWrt
archives: <https://dev.archive.openwrt.org/ticket/6533.html>.

Mark Mentovai came across the fixed antenna group when he was looking
into the driver:

    fixed_antenna_group 1, (0, 1, 0, 1)
    fixed_antenna_group 2, (0, 1, 1, 0)
    fixed_antenna_group 3, (1, 0, 0, 1)
    fixed_antenna_group 4, (1, 0, 1, 0)

Fixes: FS#3088

Reported-by: Luca Bensi
Reported-by: Maciej Mazur
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Debugged-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-06-09 21:10:45 +02:00
Daniel Golle
fd0cc72d9c oxnas: build with 8021Q VLAN support
CONFIG_VLAN_8021Q was explicitely disabled in oxnas kernel config.
Don't do that, so VLANs can be used on the target.

Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-06-09 16:47:24 +01:00
Petr Štetiar
e5aa498acb kernel: bump 5.4 to 5.4.45
Fixes CVE-2020-10757 via upstream commit df4988aa1c96 ("mm: Fix mremap
not considering huge pmd devmap").

Resolved merge conflict in the following patches:

 bcm27xx: 950-0128-gpiolib-Don-t-prevent-IRQ-usage-of-output-GPIOs.patch

Refreshed patches, removed upstreamed patch:

 generic: 751-v5.8-net-dsa-mt7530-set-CPU-port-to-fallback-mode.patch
 generic: 754-v5.7-net-dsa-mt7530-fix-roaming-from-DSA-user-ports.patch

Run tested: qemu-x86-64
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-09 16:59:33 +02:00
Perry Melange
22468cc40c ramips: erx and erx-sfp: fix missing WAN interface
This partially reverts commit 5acd1ed0be ("ramips: mt7621: fix
Ubiquiti ER-X ports names and MAC addresses"), this change was discussed
in https://github.com/openwrt/openwrt/pull/2901#discussion_r407238452

With commit 5acd1ed0be ("ramips: mt7621: fix Ubiquiti ER-X ports names
and MAC addresses"), all the ports were put into the LAN bridge, with
the argument that the OEM firmware does not have a WAN port enabled.  In
the default OEM setup, all of the ports except eth0 are dead and eth0 is
set to a static IP address without providing DHCP services when
connected.  It is only after the wizard has been run that eth0 becomes
the WAN port and all the rest of the ports belong to LAN with DHCP
enabled.

Having all of the ports set to the LAN bridge does not mirror the default
OEM setup.  To accomplish that, then only eth0 would be in the LAN bridge.
But this is not the expected behaviour of OpenWrt.

Therefore this proposal to set eth0 to WAN and eth1-N to LAN provides
the expected behaviour expected from OpenWrt, maintains the current
documentation as up-to-date, and does not require the user to manually
detach eth0 from the LAN bridge, create the WAN(6) interface(s), and set
eth0 to the WAN(6) interface(s).

Fixes: 5acd1ed0be ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses")
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
[commit subject and description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-09 16:59:33 +02:00
John Crispin
c37487a63d mediatek: fix image/mt7622.mk
Signed-off-by: John Crispin <john@phrozen.org>
2020-06-07 20:59:39 +02:00
Álvaro Fernández Rojas
6fca1646dd bcm63xx: bcm6328: switch to upstream boot sel patch
BCM6328 boot selection fix has been upstreamed.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-07 20:26:17 +02:00
Daniel González Cabanelas
ff2c96333f bcm63xx: add support for the Sercomm H500-s
Sercomm H500-s is an xDSL dual band wireless router based on Broadcom
BCM63167 SoC.

Hardware:
   SoC:          Broadcom BCM63167
   CPU:          BMIPS4350 V8.0, 400 MHz, 2 cores
   Flash:        NAND 128 MiB
   RAM:          DDR3 128 MiB
   Ethernet:     4x 10/100/1000 Mbps
   Switch:       BCM53134S
   Wireless:     802.11b/g/n: BCM435f (integrated)
                 802.11ac:    Quantenna QT3740BC (onboard SoC)
   USB:          1x 2.0
   LEDs/Buttons: 11x / 2x

Flash instruction, web UI:
  1. Reset to defaults using the reset button if the admin password is
     unknown
  2. Login into the web UI as admin.
     Address:  http://192.168.0.1
     User:     admin
     Password: VF-ESVodafone-H-500-s or l033i-h500s
  3. Go to Settings -> Firmware Update, and select the Openwrt factory
     firmware
  4. Update the firmware.
  5. Wait until it finish, the device will reboot with Openwrt installed
     on the alternative image partitions keeping the stock firmware in
     the former.

Notes:
  - The patch also adds support for the lowi version. Only the factory
    firmware is different.
  - The integrated Wifi in the Broadcom Soc isn't still supported.
  - The Quantenna 802.11ac wifi works ok, but needs to be configured with
    the Quantenna client application. It can't be configured with Luci
    nor any iw command since it's a separated subsystem linked via
    ethernet.
  - The BCM53134S external switch is managed via MDIO which isn't
    supported in this target. Therefore it will behave as a dumb switch.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-07 20:26:17 +02:00
Álvaro Fernández Rojas
9eb9d0baa0 bcm63xx: image: support device-specific load address
Some CFEs are located at the address currently used for relocation and lzma
loader load address, so we need to provide a way to override it.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-07 20:26:17 +02:00
Daniel González Cabanelas
27c20a1ef5 bcm63xx: image: don't add the CFE to the sercomm factory
There is no need to include the CFE bootloader in the Sercomm factory
images.

There might be a case when this could be useful:
  - We are running the stock firmware on the first Sercomm image
  - The second partition storing the botloader was erased (unlikely)
Even in this case flashing an image without a bootlader is harmless.

Don't include the bootloader in the factory image creation and rid of the
risk of flashing factory images with an untested bootloader partition.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-07 20:26:17 +02:00
Daniel González Cabanelas
598ba5b169 bcm63xx: kernel: add BCM63167 cpuid variant
The BCM63167 is a BCM63268 SoC with a different physical packaging.

Add the CPU ID to allow supporting routers with this SoC (i.e Sercomm
H500-s)

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-07 20:26:17 +02:00
Álvaro Fernández Rojas
66f7062160 bcm63xx: vr-3032u: add missing compatible property
SoC is a BCM63168.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-07 20:26:17 +02:00
Álvaro Fernández Rojas
57dce7c8f3 bcm63xx: vg-8050: add missing compatible property
SoC is a BCM63169.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-07 20:26:17 +02:00
John Crispin
ad39d06df7 mediatek: add mt7531 DSA support
Signed-off-by: John Crispin <john@phrozen.org>
2020-06-07 19:10:51 +02:00
John Crispin
f72a2b004c mediatek: add bpi-r64 emmc support
Signed-off-by: John Crispin <john@phrozen.org>
2020-06-07 17:53:37 +02:00
John Crispin
55b97b6885 mediatek: make emmc image generation work on mt7622
Signed-off-by: John Crispin <john@phrozen.org>
2020-06-07 17:52:21 +02:00
John Crispin
127ad76311 mediatek: switch over to extended upstream eip97 driver
Signed-off-by: John Crispin <john@phrozen.org>
2020-06-07 17:52:21 +02:00
Sungbo Eo
3559b46b62 mediatek: tidy up image subtarget Makefiles
- sort device recipes alphabetically
- adjust board name of ELECOM WRC-2533GENT
- harmonize line wrapping

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-07 15:23:16 +02:00
Stijn Tintel
050c31fa26 bcm27xx: fix unmounting /boot after sysupgrade
Due to a typo, /boot is not properly unmounted after copying the backup
file to it. Fix the typo to solve this.

Fixes: 246916ddf4 ("brcm2708: use x86's upgrade scripts for all rpi targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-06-07 06:00:08 +03:00
Kevin Darbyshire-Bryant
7b4877c204 kernel: sch_cake: use skb hash improve wireguard compatibility
While the other fq-based qdiscs take advantage of skb->hash and doesn't
recompute it if it is already set, sch_cake does not.

This was a deliberate choice because sch_cake hashes various parts of the
packet header to support its advanced flow isolation modes. However,
foregoing the use of skb->hash entirely loses a few important benefits:

- When skb->hash is set by hardware, a few CPU cycles can be saved by not
  hashing again in software.

- Tunnel encapsulations will generally preserve the value of skb->hash from
  before the encapsulation, which allows flow-based qdiscs to distinguish
  between flows even though the outer packet header no longer has flow
  information.

It turns out that we can preserve these desirable properties in many cases,
while still supporting the advanced flow isolation properties of sch_cake.
This patch does so by reusing the skb->hash value as the flow_hash part of
the hashing procedure in cake_hash() only in the following conditions:

- If the skb->hash is marked as covering the flow headers (skb->l4_hash is
  set)

AND

- NAT header rewriting is either disabled, or did not change any values
  used for hashing. The latter is important to match local-origin packets
  such as those of a tunnel endpoint.

The immediate motivation for fixing this was the recent patch to WireGuard
to preserve the skb->hash on encapsulation. As such, this is also what I
tested against; with this patch, added latency under load for competing
flows drops from ~8 ms to sub-1ms on an RRUL test over a WireGuard tunnel
going through a virtual link shaped to 1Gbps using sch_cake. This matches
the results we saw with a similar setup using sch_fq_codel when testing the
WireGuard patch.

Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-05 21:03:26 +01:00
DENG Qingfang
898969636d mvebu: remove ClearFog Pro SUPPORTED_DEVICES
A direct upgrade from previous swconfig version with
incompatible settings to DSA will break the internet.
Remove SUPPORTED_DEVICES so users cannot upgrade directly.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[rebase after Linksys rename, adjust title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-05 21:54:53 +02:00
Paul Spooren
df6f3090c4 mvebu: rename Linksys devices based on their common names
The Linksys devices in mvebu target feature a mixed naming,
where parts are based on the official product name (device
node, image; e.g. WRT3200ACM) and parts are based on the
internal code name (DTS file name, compatible, LED labels;
e.g. rango). This inconsistent naming has been perceived
as quite confusing.

A recent attempt by Paul Spooren to harmonize this naming
in kernel has been declined there. However, for us it still
makes sense to apply at least a part of these changes
locally.

Primarily, this patch changes the compatible in DTS and thus
the board name used in various scripts to have them in line
with the device, model and image names. Due to the recent
switch from swconfig to DSA, this allows us to drop
SUPPORTED_DEVICES and thus prevent seamless upgrade between
these incompatible setups.

However, this does not include the LED label rename from
Paul's initial patch: I don't think it's worth keeping the
enormous diff locally for this case, as we can implement
this much easier in 01_leds if we have to live with the
inconsistency anyway.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[rebase, extend to all devices, drop DT LED changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-05 21:54:43 +02:00
Rafał Miłecki
8c31afb978 kernel: b53: fix compilation with kernels 5.5+
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-06-05 12:42:45 +02:00
DENG Qingfang
5b9ba4a93e generic: mt7530: support adjusting EEE
Add support for adjusting EEE with ethtool

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-04 22:21:42 +02:00
DENG Qingfang
7c47f6601d generic: mt7530: fix roaming from DSA user ports
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.

Fix it by enabling SA learning on the CPU port.

To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-04 22:21:42 +02:00
DENG Qingfang
dc4ffaa5ab generic: fix DSA VLAN filtering
Currently enabling VLAN filtering blocks all traffic in the bridge
immediately. That is because DSA ignores all VLAN setup when VLAN
filtering is disabled, and when it is enabled, there is no VLAN entry
in the VLAN table, causing all traffic to be blocked.

Add patches to allow VLAN setup even if VLAN filtering is disabled.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-04 22:21:42 +02:00
DENG Qingfang
d56d05f01f generic: mt7530: set CPU port to fallback mode
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:

	bridge vlan add dev br0 vid 2 pvid untagged self
	bridge vlan del dev br0 vid 1 self
	bridge vlan add dev sw0p0 vid 2 pvid untagged
	bridge vlan del dev sw0p0 vid 1
	# br0 cannot send untagged frames out of sw0p0 anymore

That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.

Set the CPU port to fallback mode so untagged frames can pass through.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-04 22:21:42 +02:00
Felix Fietkau
81b59efefd ramips/mediatek: select kmod-mt7615-firmware where kmod-mt7615e is selected
The new mt76 version splits out the firmware, because the driver can also be
used for MT7663/MT7613

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-06-04 21:52:57 +02:00
Felix Fietkau
2dd26fda16 kernel: fix portability issue with perf on linux 5.4
Remove dependencies on core kernel headers in host tools used to build perf,
which break on any non-linux system

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-06-04 21:52:57 +02:00
DENG Qingfang
712e00877d mvebu: rename Linksys Mamba WAN port
Rename it to wan to match Linksys Armada 385 series

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-03 20:34:15 +02:00
DENG Qingfang
5a49cbf6c4 mvebu: remove swconfig package
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-03 20:34:15 +02:00
DENG Qingfang
24410595e9 generic: backport mv88e6xxx port mirroring support
Backport port mirroring support for mv88e6xxx

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-03 20:34:15 +02:00
DENG Qingfang
be309bfd74 mvebu: drop 06_set_iface_mac preinit script
MAC address is set in board.d script
Interface swapping is not needed anymore as switching to DSA breaks
previous configuration anyway

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-03 20:34:15 +02:00
DENG Qingfang
9b34ea4f62 mvebu: use ucidef to set up MAC address
Use ucidef to set up MAC address instead of preinit script

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-03 20:34:15 +02:00
DENG Qingfang
4149d2b91c mvebu: use eth0 as DSA CPU port for Linksys WRT
eth0 has HW MAC address while eth2 does not.
Use eth0 instead so we don't have to set LAN MAC manually.
Disable unused eth2, until multi CPU port is supported.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-03 20:34:14 +02:00
DENG Qingfang
f799c65946 mvebu: update default config for DSA
Update network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will break the ethernet.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-03 20:34:14 +02:00
DENG Qingfang
6058035e37 mvebu: remove swconfig symbols from kernel config
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-03 20:34:14 +02:00
DENG Qingfang
a2bca5c922 mvebu: drop swconfig patches
Drop swconfig patches for Clearfog and Linksys WRT

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-06-03 20:34:14 +02:00
Adrian Schmutzler
5fcb0723a3 mvebu: switch to kernel 5.4
Last reports with kernel 5.4 have all been positive [1], so let's open
this to a wider range of testers.

[1] https://github.com/openwrt/openwrt/pull/2804

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-03 20:34:14 +02:00
Álvaro Fernández Rojas
8421ea7de1 bcm63xx: vg-8050: fix WFI partition size
Each image can take up to 0x3d60000, which means 128k more per image.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-03 19:06:22 +02:00
Álvaro Fernández Rojas
e8aac7013a bcm63xx: vr-3032u: fix WFI partition size
Each image can take up to 0x3d60000, which means 128k more per image.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-03 19:03:42 +02:00
Álvaro Fernández Rojas
6c7cbf1420 kernel: mtdsplit: bcm_wfi: always add img partitions
This is useful when booting OpenWrt from ramdisks in order to have both
images partitions defined.
Furthermore, instead of always using img2 for the inactive image, let's use
img1 or img2 accordingly.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-03 18:50:58 +02:00
Tobias Schramm
2f5a242f67 ramips: mt7621: use higher SPI clock speed on Mikrotik rbm11g and rbm33g
Previously the dts were using a value determined by empirical testing,
because of a spi driver/clock bug. The bug was fixed quite some time
ago. 33 MHz is the default clock frequency used by RouterBOOT and thus
safe.

Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
2020-06-03 16:49:28 +02:00
Sungbo Eo
6ea87d35c6 bcm47xx: fix brcm-wl module loading
_dma_cache_wback_inv needs to be exported to load wl module successfully.

root@OpenWrt:/# insmod wl
[  363.867779] wl: Unknown symbol _dma_cache_wback_inv (err -2)
failed to insert /lib/modules/5.4.40/wl.ko

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Cc: Rafał Miłecki <rafal@milecki.pl>
2020-06-03 16:49:28 +02:00
Tim Harvey
0cf101d6b3 octeontx: fix mcp251x can controller
Update the can-mcp251x-convert-to-half-duplex-SPI patch to fix reception

Some SPI host controllers such as the Cavium Thunder TX do not support
full-duplex SPI. Using half-duplex transfers allows the driver to work
with those host controllers.

This patch fixes the fact that mcp251x_hw_rx_frame was still relying on
a full-duplex transfer where bits were being shifted on MOSI at the same time
as MISO. After splitting the transaction into a spi_write_then_read() care
must be taken to ignore the first byte.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-06-03 16:49:28 +02:00
Tim Harvey
3fd8e86079 octeontx: fix gpio irq request
This fixes a regression in 5.4 that causes a crash when a driver requests
an ARM GPIO for an IRQ.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-06-03 16:49:28 +02:00
Tim Harvey
c3f9598339 octeontx: refresh kernel 5.4 config
refresh kernel config by running make kernel_menuconfig and saving changes

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-06-03 16:49:28 +02:00
Tim Harvey
0562037c3b imx6: image: increase max ubifs file-system size
The latest 2GiB NAND flash parts used by Gateworks ventana are 2K page-size.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-06-03 16:49:28 +02:00
Tim Harvey
3b1e99d23e imx6: backport v5.8 imx6qdl-gw dt patches
- add fxos8700 support to GW52xx/GW53xx/GW54xx
- add USB_OTG support to GW552x
- add LSM9DS1 IMU support to GW560x
- add LSM9DS1 IMU support to GW5904
- add CC1352 UART to GW5910
- add BCM4330 support to GW5910
- fix wlan regulator for GW5910

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-06-03 16:49:28 +02:00
Florian Eckert
0b3e1205df kernel: add gpio-it87
Since commit 910df3f06c we have build in
on all X86/64 platforms the gpio-it87 driver.

Since this change I am getting the following error message on boot.
 > kern.err kernel: [    1.009416] gpio_it87: no device

I do not have this device on my system. To prevent the nonsensical
message and the loading of the module I have added this as a package, so
that it can be installed later or during image building.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
2020-06-03 16:49:28 +02:00
Johann Neuhauser
1d9812f48a ath79: phy-ar7200-usb: do not print error on defered init
This is only a cosmetic correction, as the driver works as expected.
However, the error message confuses users about a missing reset definition.

On a defered init we don't see the following error message now:
[    0.078292] ar7200-usb-phy usb-phy: phy reset is missing

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2020-06-03 16:49:28 +02:00
Tomasz Maciej Nowak
cf69472fb1 mvebu: espressobin: fix SATA and USB 3.0 ports detection
This commit removes changes from upstream commits:
8e18c8e58da6 arm64: dts: marvell: armada-3720-espressobin: declare SATA
PHY property
bd3d25b07342 arm64: dts: marvell: armada-37xx: link USB hosts with their
PHYs
For most boards which have factory bootloader this caused that devices
connected to USB 3.0 and SATA port were not detected. For them to
function users would need to upgrade the bootloader to version with ARM
Trusted Firmware 2.1 or later. Unfortunately there is no official
bootloader image with updated ATF component, therefore drop these
properties from nodes. This change was also tested briefly with
bootloader with updated ATF and the ports functioned properly.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-06-03 16:49:28 +02:00
Thomas Albers
f93fcf8923 ipq806x: enable disk-activity LED trigger
Enable the disk-activity LED trigger for ipq806x, since this SoC has an
onboard SATA controller.

Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[split into separate commit]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-03 16:49:28 +02:00
Thomas Albers
e23859765c linux/generic: remove obsolete config option LEDS_TRIGGER_IDE_DISK
Kernel config option LEDS_TRIGGER_IDE_DISK was renamed in kernel 4.8 to
CONFIG_LEDS_TRIGGER_DISK in upstream commit eb25cb9956cc ("leds: convert
IDE trigger to common disk trigger").

Removing it as it should be added only on targets which has usage for
this trigger.

Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-03 16:49:28 +02:00
Alexey Dobrovolsky
0a182fcba6 ramips: add kmod-usb-dwc2 to ZyXEL Keenetic image
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.

Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-03 16:49:28 +02:00
Alexey Dobrovolsky
ab841b4393 ramips: remove patches for USB-dwc2
In FS#2738 we can see that patch first introduced in
e8ebcff ("ramips: add a explicit reset to dwc2")
breaks USB functionality since 18.06. Thus, this patch should be removed.

Removed:
- 0032-USB-dwc2-add-device_reset.patch

Fixes: FS#2738
Fixes: FS#2964

Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
2020-06-03 16:49:28 +02:00
Adrian Schmutzler
04373e20cb apm821xx: set DEVICE_TYPE to "nas" for sata subtarget
Since DEVICE_TYPE cannot be set per device, just set DEVICE_TYPE
to "nas" for the entire subtarget, which only contains this single
device.

Note that while this looks like a cosmetic change in combination
with the previous patches, this particular patch actually changes
the packages for the device.

Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-03 15:41:09 +02:00
Adrian Schmutzler
057e5f6ede treewide: provide consistent basic DEVICE_TYPE
While the effective "default" based on frequent use is "router", the
DEVICE_TYPE variable actually provides a "basic" configuration without
selecting any additional packages.

This is currently set up with the identifier "bootloader", which seems
to be not used at all. However, the only targets not using "router" or
"nas" are actually archs38 and arc770, which use their own value
"developerboard" for DEVICE_TYPE which seems to have been invented when
these targets where added. The latter is not implemented in target.mk,
though, and will fall back to the "basic" set of packages then.

So, to clean this up and make it more readable, let's just define a
DEVICE_TYPE "basic" and use it for the aforementioned cases.

Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-03 15:41:09 +02:00
Adrian Schmutzler
64ebf74c05 treewide: drop DEVICE_TYPE when used as device variable
DEVICE_TYPE is a target/subtarget variable, and it does not have
any effect when set in a device definition. It can only be set
in a target's or subtarget's Makefile.

Consequently, having it set anyway is misleading, so this drops
all cases.

This effectively reverts the following commits:
7a1497fd60 ("apm821xx: MBL: set DEVICE_TYPE to NAS")
5b4765c93a ("gemini: Classify Raidsonic NAS IB-4220-B as a NAS")
cdc6de460b ("gemini: D-Link DNS-313 is a NAS")

For the following commit, the variable was set when adding device
support:
27b2f0fc0f ("kirkwood: add support for Iomega Storcenter ix2-200")

Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-03 15:41:09 +02:00
Álvaro Fernández Rojas
6dc01cdee8 bcm63xx: lzma-loader: allow bigger ramdisks
Some (older) CFEs are loaded at 0x80401000 and ramdisks are loaded at
0x80010000, which means that ramdisk size limit is 0x3F1000 (almost 4M).
Therefore, current ramdisks (~4MB) are overwritting CFE in these devices,
which results in a crash.

This commit changes the address where ramdisks are loaded to 0x80a00000,
which is the same address where kernel is loaded when booting from the flash.
Therefore, lzma-loader will now be loaded at 0x80a00000, but it will still
decompress the kernel at 0x80010000.

Tested with huawei,hg556a-b, which has its CFE loaded at 0x80401000.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-03 15:33:04 +02:00
Daniel Golle
646bfe0842 malta: add missing symbols for kernel 5.4
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-06-03 10:50:01 +01:00
Álvaro Fernández Rojas
231f728f69 bcm63xx: ad1018: remove cfe.bin image support
Apparently, Sercomm allows loading a BCM WFI image via CFE, but this image
destroys "serial" and "protect" nand partitions, which is wrong.
It will also set both bootflags to the same value, which causes booting
issues with cferam (cferom will alternatively boot from cferam1 or cferam2
each time the device is rebooted).
Now that OEM Sercomm images are supported it's time to remove this hacky
cfe.bin image support.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-03 11:34:28 +02:00
Álvaro Fernández Rojas
39f44be1dc bcm63xx: ad1018: add missing partitions
This partitions were missing when support for this device was added.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-03 11:18:11 +02:00
Álvaro Fernández Rojas
b302a44206 bcm63xx: stop using legacy lzma for all devices
BCM6368 and newer devices are compatible with any lzma compression parameters.
Add a new legacy device definition and use it on BCM6358 and older devices.

Compressed kernel size is reduced by ~1.35%.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-03 09:50:00 +02:00
Álvaro Fernández Rojas
e73c61a978 bcm63xx: vg-8050: switch to bcm-wfi-split
Allows to keep a backup firmware in case active firmware is corrupted.
Also fix hsspi address warning.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 18:25:44 +02:00
Álvaro Fernández Rojas
b1d375b744 bcm63xx: vr-3032u: switch to bcm-wfi-split
Allows to keep a backup firmware in case active firmware is corrupted.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 18:23:40 +02:00
Álvaro Fernández Rojas
82cf488819 bcm63xx: nand: order devices alphabetically
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 18:23:40 +02:00
Álvaro Fernández Rojas
824cb78cf3 bcm63xx: nand: add CFE_WFI_VERSION values for each device
CFE_WFI_VERSION should be defined per device instead of using a generic value.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 18:23:40 +02:00
Álvaro Fernández Rojas
18d2eeab8e kernel: mtdsplit: support Broadcom WFI bootflags
When firmware is flashed, cferam.000 extension is renamed to the next number.
When booting, CFE scans the NAND and picks the partition with the highest
cferam extension and ignores the other one.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 18:23:40 +02:00
Álvaro Fernández Rojas
1fd3dabfaf kernel: mtdsplit: improve JFFS2 scan
Allow retrieving full file name and length by parameters.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 18:23:40 +02:00
Álvaro Fernández Rojas
eed8a927ee kernel: mtdsplit: bcm_wfi: refactor code
Create new parse_bcm_wfi function with common code from current parsers.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 18:23:40 +02:00
Petr Štetiar
392c64d8fd kernel: bump 5.4 to 5.4.43
Refreshed patches, removed upstreamed patch:

 bcm27xx: 950-0642-component-Silence-bind-error-on-EPROBE_DEFER.patch

Run tested: qemu-x86-64
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-02 17:46:51 +02:00
Álvaro Fernández Rojas
e238c85e57 bcm63xx: nand: sercomm: switch to sercomm-load script
xxd is not a valid dependency and shouldn't be used.
Fixes buildbot failure.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 13:10:00 +02:00
Álvaro Fernández Rojas
a47acae319 bcm63xx: ad1018: support Sercomm factory images
This images can be flashed from the official firmware, as opposed to CFE
images, which can only be flashed from CFE and require opening the case.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 09:16:49 +02:00
Álvaro Fernández Rojas
f263a0f9ff bcm63xx: nand: support Sercomm firmwares
Add support for Sercomm factory firmwares (AES 256 CBC encrypted).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 09:12:05 +02:00
Álvaro Fernández Rojas
4b2fe12953 kernel: mtdsplit: bcm_wfi: remove brcm,wfi-sercomm compatibility
The only Sercomm WFI user has been migrated to a dedicated firmware parser.
Keep support for no cferam partition based on a boolean DT property.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 09:08:38 +02:00
Álvaro Fernández Rojas
80d8114802 bcm63xx: ad1018: switch to Sercomm WFI
Support Sercomm firmware partition split.
WFI partition must be defined after bootflag partitions in order for the
parser to properly find bootflag1 and bootflag2 partitions.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 09:08:36 +02:00
Álvaro Fernández Rojas
fce7380e0e kernel: mtdsplit: bcm_wfi: support Sercomm bootflags
Sercomm uses 2 bootflag partitions and boots the firmware with the highest
bootflag. Support splitting the firmware partition while keeping support for
unsplitted layout.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 09:08:30 +02:00
Álvaro Fernández Rojas
cd81d105d5 kernel: mtdsplit: bcm_wfi: code refactoring
- Rename master to mtd.
- Pass mtd size as an argument.
- Rename of_match_table.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-06-02 08:50:15 +02:00
David Bauer
b017a016cc ar71xx: correct button type for TL-MR3020 mode slider
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.

Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.

Related: commit 27f3f493de ("gpio-button-hotplug: unify polled and
interrupt code")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-31 15:53:01 +02:00
Adrian Schmutzler
91b1a625f4 ath79: add label MAC address for TP-Link RE450 v2/v3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Andreas Wiese
c764c512ac ath79: add support for TP-Link RE450 v3
TP-Link RE450 v3 is a dual band router/range-extender based on
Qualcomm/Atheros QCA9563 + QCA9880.

This device is nearly identical to RE450 v2 besides a modified flash
layout (hence I think force-flashing a RE450v2 image will lead to at
least loss of MAC address).

Specification:

- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button-
- possible UART header on PCB¹

Flash instruction:
Apply factory image in OEM firmware web-gui.

¹ Didn't check to connect as I didn't even manage to connect on
  RE450v2 (AFAIU it requires disconnecting some resistors, which I was
  too much of a coward to do).  But given the similarities to v2 I
  think it's the same or very similar procedure (and most likely also
  the only way to debrick).

Signed-off-by: Andreas Wiese <aw-openwrt@meterriblecrew.net>
[remove dts-v1 and compatible in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Lech Perczak
7e513136c6 ath79: add support for TP-Link TL-WR802N V1 and V2
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
  [V1] http://192.168.0.1
  [V2] http://192.168.0.254
  Default user is "admin" & password is "admin".
  On V2, there is no DHCP server running by default, so remember to set
  IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
  [V1] "*.factory.bin"
  [V2] "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
  Web interface may complain if filename is too long. In such case,
  rename .bin to something shorter.
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Notes:

When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.

The MAC address assignment has been checked with OEM firmware.

Installation manual based on ar71xx support by Thomas Roberts

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Lech Perczak
f841e70640 ar71xx: fix reset key for TP-Link TL-WR802N V1/V2
During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.

Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.

Fix it.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Roger Pueyo Centelles
95caa3436d ath79: update WA/XC devices UBNT_VERSION to 8.5.3
Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION
to be at least 8.5.3, otherwise the image is rejected:

   New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3
   Versions: New(525568) 8.5.0, Required(525571) 8.5.3
   Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3'

For consistency, also increase version number for XC devices.

Tested-by: Pedro <pedrowrt@cas.cat>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-05-31 15:44:05 +02:00
Samantha Collard
0f910a8c4c ipq806x: EA8500 fix boot partition detection
Remove extraneous code that disabled boot partition detection.

Fixes: b3770eaca3 ("mtd: base-files: Unify dual-firmware devices (Linksys)")
Signed-off-by: Samantha Collard <sammyrc34@gmail.com>
2020-05-31 15:44:05 +02:00
Adrian Schmutzler
705fe43522 ath79: fix LEDs for GL.inet GL-AR150
Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.

In addition, a look into the manual revealed that the OEM
configuration is as follows:

LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless

So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Adrian Schmutzler
c3742ce38c bcm53xx: remove support for kernel 4.14
We currently support three kernel versions on this target, let's
just get rid of the oldest one.

Cc: Rafał Miłecki <rafal@milecki.pl>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-30 11:30:06 +02:00
Adrian Schmutzler
06feb09e54 bcm47xx: remove support for kernel 4.14
We currently support three kernel versions on this target, let's
just get rid of the oldest one.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-30 11:30:06 +02:00
Adrian Schmutzler
a7b07f8ba8 ar71xx: fix splitting firmware partition for TL-WR902AC v1
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.

This led to bootloops after using sysupgrade.

Fixes: FS#3118

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-30 00:35:24 +02:00
Álvaro Fernández Rojas
77e97abf12 bcm27xx: update to latest patches from RPi foundation
Also removes random module and switches to new bcm2711 thermal driver.
Boot tested on RPi 4B v1.1 4G.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-28 19:12:43 +02:00
Jakov Petrina
3dbb658d26 linux: mvebu: backport mvneta XDP support fixes
This patch backports additional fixes for XDP support in the mvneta driver. These
changes are found upstream as commits:

b37fa92e20ef2 net: mvneta: fix build skb for bm capable devices
f383b2950070c net: mvneta: rely on page_pool_recycle_direct in mvneta_run_xdp
79572c98c554d mvneta driver disallow XDP program on hardware buffer management
44efc78d0e464 net: mvneta: fix XDP support if sw bm is used as fallback

Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
2020-05-28 11:43:13 +02:00
Jakov Petrina
76f9aa6f4b linux: mvebu: backport mvneta XDP support
This patch backports XDP support in the mvneta driver used by Marvell ARMADA 37x,
38x and 37xx series SoCs. Supported actions are:

- XDP_DROP
- XDP_PASS
- XDP_REDIRECT
- XDP_TX

Patches are present upstream as following commits:

* b0a43db9087a net: mvneta: add XDP_TX support
* 9e58c8b41065 net: mvneta: make tx buffer array agnostic
* fa383f6b77a2 net: mvneta: move header prefetch in mvneta_swbm_rx_frame
* 0db51da7a8e9 net: mvneta: add basic XDP support
* 8dc9a0888f4c net: mvneta: rely on build_skb in mvneta_rx_swbm poll routine
* 568a3fa24a95 net: mvneta: introduce page pool API for sw buffer manager
* ff519e2acd46 net: mvneta: introduce mvneta_update_stats routine

Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
2020-05-28 11:43:13 +02:00
Thibaut VARÈNE
f10da7cb4d packages/boot: remove rbcfg
The new sysfs soft_config driver makes buggy rbcfg obsolete and
entirely replaces it.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Thibaut VARÈNE
48b14b9cbe generic: routerboot sysfs: soft_config support for ath79 cpufreq
This commit introduces support for R/W access to the CPU frequency
setting of routerboot on ath79 hardware.

On unsupported hardware, the sysfs attribute will expose the raw tag
value (read-only) to help with reverse engineering its meaning.

Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Thibaut VARÈNE
89226b8666 generic: routerboot sysfs: move tag_show_u32()
This routine will be shared between hard and soft config drivers.

Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Thibaut VARÈNE
f36e710e2d generic: routerboot sysfs: add support for soft_config
This driver exposes the data encoded in the "soft_config" flash segment
of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder
named "soft_config" through a set of human-and-machine-parseable
attributes. Changes can be discarded by writing 0 to the 'commit'
attribute, or they can be committed to flash storage by writing 1.

This driver does not reuse any of the existing code previously found in
the "rbcfg" utility and makes this utility obsolete by providing a clean
sysfs interface.

Like "rbcfg", this driver requires 4K_SECTORS support since the flash
partition in which these parameters are stored is typically 4KB in size.

Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Thibaut VARÈNE
dac18f66fb generic: routerboot sysfs: move tag_show_string()
This routine will be shared between hard and soft config drivers.
Also use scnprintf() instead of snprintf().

Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Thibaut VARÈNE
39ec3c5986 generic: platform/mikrotik: rb_hardconfig.c minor fixes
For the sake of strictly typed code, add a missing const qualifier.
Add a missing return value in error path.
Check the return value of mtd_read(), for good measure.
Also demote the error printks of failed sysfs file creation to warn
level since they are not fatal in the init() sequence.
Finally, add a note regarding PAGE_SIZE and clarify a comment.

Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Thibaut VARÈNE
429fbc96a4 generic: platform/mikrotik: reorder Kconfig
The depends and select should apply to the sysfs driver, not the meta
config.

Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Álvaro Fernández Rojas
584d4bf1d3 bcm27xx: update patches from RPi foundation
bcm2708: boot tested on RPi B+ v1.2
bcm2709: boot tested on RPi 3B v1.2
bcm2710: boot tested on RPi 3B v1.2
bcm2711: boot tested on RPi 4B v1.1 4G

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-28 10:36:27 +02:00
Álvaro Fernández Rojas
745c447579 bcm27xx: remove linux 4.19 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-28 10:36:27 +02:00
Pavel Balan
ad84c09502 ath79: add support for COMFAST CF-E130N v2
This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
CPE with a single Ethernet port and a 802.11bgn radio.

Specifications:

 - QCA9531 SoC
 - 1x 10/100 Mbps Ethernet with PoE-in support
 - 64 MB of RAM (DDR2)
 - 16 MB of FLASH
 - 5 dBi built-in antenna
 - POWER/LAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI.

 The U-boot bootloader also contains a backup TFTP client to upload the
 firmware from. Upon boot, it checks its ethernet network for the IP
 192.168.1.10. Host a TFTP server and provide the image to be flashed as
 file firmware_auto.bin.

MAC address setup:

The art partition contains four consecutive MAC addresses:

0x0    aa:bb:cc:xx:xx:c4
0x6    aa:bb:cc:xx:xx:c6
0x1002 aa:bb:cc:xx:xx:c5
0x5006 aa:bb:cc:xx:xx:c7

However, the manufacturer in its infinite wisdom decided that one address
is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's
overwriting the existing and valid address in 0x1002). This is obviously
also the address on the device's label.

Signed-off-by: Pavel Balan <admin@kryma.net>
[fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename
ATH_SOC to SOC]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-28 01:47:54 +02:00
Adrian Schmutzler
2b92ee36ae ath79: replace tab after DT label by space
The common separator in this case is a single space.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-28 00:48:39 +02:00
Adrian Schmutzler
e8fbb98c6d ramips: fix LED DT label for Zyxel Keenetic Start
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-27 18:31:46 +02:00
Sebastian Schaper
64d088d8f9 ath79: increase spi clock for D-Link DIR-842
AHB is 258 MHz for this device (CPU_PLL / 3), but there is no difference
between 64 MHz and 50 MHz for spi-max-frequency, thus increase to 50 MHz.

Tested on revisions C1 and C3.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-05-26 22:49:18 +02:00
Sebastian Schaper
8643c0b53d ath79: define switch reset-gpios for D-Link DIR-842
GPIO 11 needs to be pulled high for the external gigabit switch to work,
this is currently solved via gpio-hog. Replace with phy0 reset-gpios.

Tested on revisions C1 and C3. Reset button is still working for reboot,
to enter failsafe, and to enter bootloader http recovery.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-05-26 22:49:18 +02:00
Sebastian Schaper
6ce1e299be ath79: fix LEDs for D-Link DIR-842
The device has a total of 8 LEDs, 5 of which are controlled by the switch
(LAN 1-4, WAN). Only power, wifi and wps are controlled by the SoC.

 * led_power is on GPIO 5 (not 15), boot flashing sequence is now visible
 * remove led 'internet', since it is only connected to the switch
 * remove ucidef_set_led_switch for WAN from 01_leds, as it has no effect

Tested on revisions C1 and C3.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 22:49:18 +02:00
Adrian Schmutzler
0225018d8b ramips: create shared DTSI for DIR-810L and TEW-810DR
These devices seem to have the same board, so let's have a common
file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 22:04:11 +02:00
J. Scott Heppler
168e4c91d8 ramips: add support for TRENDnet TEW-810DR
Specifications:

* MediaTek MT7620A (580 Mhz)
* 8 MB of FLASH
* 64 MB of RAM
* 2.4Ghz and 5.0Ghz radios
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* UART header on PCB (57600 8n1)
* Green/Orange Power LEDs illuminating a Power-Button Lens
* Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
* 3x button - wps, power and reset
* U-boot bootloader

Installation:

The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
appended.  ncc_att_hwid is a 32bit binary in the GPL Source download for either
the TEW-810DR or DIR-810L and is located at
source/user/wolf/cameo/ncc/hostTools.

The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"

This may need to be altered if your hardware version is "1.1R".

The image can also be directly flashed via serial tftp:
1.  Load *.sysupgrade.bin to your tftp server directory and rename for
    convenience.
2.  Set a static ip 192.168.10.100.
3.  NIC cable to a lan port.
4.  Serial connection parameters 57600,8N1
5.  Power on the TEW-810 and press 4 for a u-boot command line prompt.
6.  Verify IP's with U-Boot command "printenv".
7.  Adjust tftp settings if needed per the tftp documentation
8.  Boot the tftp image to test the build.
9.  If the image loads, reset your server ip to 192.168.1.10 and restart network.
10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.

Notes:

The only valid MAC address is found in 0x28 of the factory partition.
Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx

Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[remove "link rx tx" in 01_leds, format and extend commit message,
fix DTS led node names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 22:04:11 +02:00
Roger Pueyo Centelles
8383e63808 ath79/mikrotik: add missing kernel config symbol for 5.4
The UBIFS_FS_ZSTD is exposed when UBIFS is enabled.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 11:46:46 +02:00
Adrian Schmutzler
4661b05390 kernel: properly insert local mtd partition parsers
Between 4.19 and 5.4, the kernel moved the partition parsers into
the parsers subdirectory. This led to some necessary rebasing of
our local patches for parsers, which partially has been performed
without caring about where the code was inserted.

This commit tries to adjust our local patches so that parsers are
inserted at the "proper" positions with respect to alphabetic sorting
(if possible). Thus, the commit is cosmetic.

While this might look useless now, it will make life easier when
adding other parsers in the future or for rebasing on kernel changes.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-25 21:11:47 +02:00
Adrian Schmutzler
b91b7d8963 kernel: remove a bunch of trailing whitespaces
These trailing whitespaces were reported during kernel patch refresh.

While at it, harmonize a few indents as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-25 21:11:47 +02:00
Adrian Schmutzler
807366af38 kernel: drop backported gpio emulated open drain output fix
This patch has been backported to stable kernel 5.4 already.

Remove our local patch explicitly now, as by applying the patch
(or refreshing) the relevant code is actually added a second time.

Refresh remaining patches as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-25 21:10:44 +02:00
Adrian Schmutzler
1b2144e81f octeon: set 5.4 as default kernel
octeon has provided 5.4 as testing kernel for some time now, let's
switch to 5.4 to have a bigger audience for testing.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-25 12:04:55 +02:00
Adrian Schmutzler
73936e77ea octeontx: remove support for kernel 4.14
Kernel 5.4 is stable for about two months now and there is only a few
patches anyway, so this is mostly upstream stuff. Therefore, it does
not look like we need to keep old 4.14 around any longer.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-25 12:03:17 +02:00
Adrian Schmutzler
0efa8cb0a8 archs38: remove support for kernel 4.14
Kernel 5.4 is stable for about two months now and there is only one
patch anyway, so this is mostly upstream stuff. Therefore, it does
not look like we need to keep old 4.14 around any longer.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-25 12:03:02 +02:00
Yangbo Lu
4bbc0e7357 layerscape: remove support for kernel 4.14
Remove support for kernel 4.14, and NXP Layerscape SDK
had not supported kernel 4.14 since LSDK-20.04 either.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-25 11:48:54 +02:00
Álvaro Fernández Rojas
b1604b744b bcm63xx: ar-5315u: expose LEDs through controller
Exposing LEDs through LED controller instead of gpio-leds takes
advantage of HW blinking.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-24 20:19:21 +02:00
Álvaro Fernández Rojas
d361aa2ebd bcm63xx: ar-5387un: expose LEDs through controller
Exposing LEDs through LED controller instead of gpio-leds takes
advantage of HW blinking.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-24 20:17:34 +02:00
Álvaro Fernández Rojas
09b7922aaa bcm63xx: ar-5381u: expose LEDs through controller
Exposing LEDs through LED controller instead of gpio-leds takes
advantage of HW blinking.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-24 20:16:30 +02:00
INAGAKI Hiroshi
7b01567976 ramips: add alternative name for Buffalo WSR-2533DHP
Buffalo WSR-2533DHP is identical to the WSR-2533DHPL, Buffalo sold it
with renaming.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-05-24 18:14:59 +02:00
Ernst Spielmann
c3dc52e39a ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1
Specifications:

- MT7628NN @ 580 MHz
- 32 MB RAM
- 8 MB Flash
- 5x 10/100 Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas (1x for RT-N10P V3)

Flash instructions:

1. Set PC network interface to 192.168.1.75/24.
2. Connect PC to the router via LAN.
3. Turn router off, press and hold reset button, then turn it on.
4. Keep the button pressed till power led starts to blink.
5. Upload the firmware file via TFTP. (Any filename is accepted.)
6. Wait until the router reboots.

Signed-off-by: Ernst Spielmann <endspiel@disroot.org>
[fix node/property name for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-24 18:14:59 +02:00
Stijn Segers
9a1f4b2f83 ath79/nand: add support for Netgear WNDR4300SW
This patch adds support for the WNDR4300SW, marketed by California ISP
SureWest (hence the 'SW' suffix). Hardware wise, it's identical to the
WNDR4300 v1.

Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2,4 GHz)
* Ethernet: 5x 1000Base-T
* LED: Power, WAN, LAN, WiFi, USB, WPS
* UART: on board, to the right of the RF shield at the top of the board

Installation:

* Flashing through the OEM web interface:
  + Connect your computer to the router with an ethernet cable and browse
    to http://192.168.1.1/
  + Log in with the default credentials are admin:password
  + Browse to Advanced > Administration > Firmware Upgrade in the Netgear
    interface
  + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img
  + Proceed with the firmware installation and give the device a few
    minutes to finish and reboot.

* Flashing through TFTP:
  + Configure your wired client with a static IP in the 192.168.1.x range,
    e.g. 192.168.1.10 and netmask 255.255.255.0.
  + Power off the router.
  + Press and hold the RESET button (the factory reset button on the bottom
    of the device, with the red circle around it) and turn the router on
    while keeping the button pressed.
  + The power LED will start flashing orange. You can release the button
    once it switches to flashing green.
  + Transfer the image over TFTP:
    $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2020-05-24 14:44:00 +02:00
Russell Senior
fe9a2beecb ramips: fix 04_led_migration case syntax for mt7621
Commit f761f4052c had bogus case syntax, the uci-defaults script threw
errors as a result and exited non-zero, probably didn't do what was
intended, but tried over and over since the non-zero exit prevents the
script from being deleted.

Fixes: f761f4052c ("ramips: mt7621: harmonize naming scheme for Mikrotik")

Signed-off-by: Russell Senior <russell@personaltelco.net>
[extend commit title, add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-23 11:38:09 +02:00
David Bauer
ebddc5f984 ath79: add support for Enterasys WS-AP3705i
Hardware
--------
SoC:    Atheros AR9344
RAM:    128M DDR2
FLASH:  2x Macronix MX25L12845EM
        2x 16MiB SPI-NOR
WLAN2:  Atheros AR9344 2x2 2T2R
WLAN5:  Atheros AR9580 2x2 2T2R
SERIAL: Cisco-RJ45 on the back (115200 8n1)

Installation
------------

The U-Boot CLI is password protected (using the same credentials as the
OS). Default is admin/new2day.

1. Download the OpenWrt initramfs-image. Place it into a TFTP server
   root directory and rename it to 1401A8C0.img. Configure the TFTP
   server to listen at 192.168.1.66/24.

2. Connect the TFTP server to the access point.

3. Connect to the serial console of the access point. Attach power and
   interrupt the boot procedure when prompted (bootdelay is 1 second).

4. Configure the U-Boot environment for booting OpenWrt from Ram and
   flash:

   $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf230000'
   $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
     tftpboot 0x85000000; bootm'
   $ setenv bootcmd 'run boot_openwrt'
   $ saveenv

5. Load OpenWrt into memory:

   $ run ramboot_openwrt

   Wait for the image to boot.

6. Transfer the OpenWrt sysupgrade image to the device. Write the image
   to flash using sysupgrade:

   $ sysupgrade -n /path/to/openwrt-sysuograde.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-22 21:54:30 +02:00
Daniele Castro
d6f66dd88e brcm63xx: add support for ADB P.DG A4001N A-000-1A1-AX
ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI)
has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected
to different GPIO PINs in active low configuration.

OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE.
It has different LEDs configuration and flash size/layout
w.r.t the ADB P.DG A4001N A-000-1A1-AX.

Hardware:
* Board ID: 96328avng
* SoC: Broadcom BCM6328
* RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01)
* LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, TX  NC  RX, on J5 connector (short R192 and R193)
                         NC  GND NC

Installation via CFE:
* Stock CFE has to be overwriten with one for 96328avng boards that can upload
  .bin images with no signature check (cfe-A4001N-V0000_96328avng.bin)
* connect a serial port to the board
* Stop the boot process after power on by pressing enter
* set static IP 192.168.1.2 and subnet mask 255.255.255.0
* navigate to http://192.168.1.1/
* upload the OpenWrt image file

Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-22 21:23:21 +02:00
Adrian Schmutzler
e3e17b4ed4 bcm63xx: use model part of board name as variable in 01_leds
This extracts the model part of the board name and uses it for the
LED string identifiers in 01_leds. As this makes statements more
generic, it will allow to merge more cases in the future.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-22 18:28:01 +02:00
Adrian Schmutzler
5a7d11fb78 bcm63xx: replace further "ok" with "okay" in DTS files
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-22 18:26:29 +02:00
Hauke Mehrtens
586661018e ath79: Do not build buffalo_whr-g301n by default
The squashfs partition is getting too big.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-05-21 22:16:17 +02:00
Álvaro Fernández Rojas
78a0ae9023 bcm63xx: WIP: add Huawei HG253s v2 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-21 19:11:24 +02:00
Álvaro Fernández Rojas
5998c8f059 bcm63xx: nand: support CFE partition tags
Introduce support for generating JFFS2 CFE partition tags.
This is used in NAND devices in order to verify the integrity of the JFFS2
partition.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-21 19:11:24 +02:00
Álvaro Fernández Rojas
6dc3dce658 bcm63xx: improve rgmii ctrl overrides
There are older devices which require overriding the RGMII ports, so this
shouldn't be limited and forced to BCM63268.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-21 19:11:24 +02:00
Álvaro Fernández Rojas
7a817752f6 bcm63xx: dgnd3700-v1: add NAND support
NAND is used as extra storage on this device.

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-21 19:11:24 +02:00
Álvaro Fernández Rojas
67861b2a66 bcm63xx: nand: fix v2.1 controller support
Page size shift is different from v2.2+ controllers

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-21 19:11:23 +02:00
Russell King
6593ea23e5 kernel: backport the I2C bus recovery for uDPU
Backport the I2C bus recovery DT configuration for the uDPU that has
been queued for 5.8.

Signed-off-by: Russell King <linux@armlinux.org.uk>
2020-05-21 12:55:31 +02:00
Russell King
714199ec34 kernel: backport v5.8 i2c-pxa updates
Add i2c-pxa updates queued for v5.8, which add bus recovery to this
driver; this is needed for the uDPU platform.

Signed-off-by: Russell King <linux@armlinux.org.uk>
2020-05-21 12:55:31 +02:00
Russell King
72a1d5c3ac kernel: backport gpio emulated open drain output fix
Backport the GPIO emulated open drain output fix from v5.5, which is
required for the i2c-pxa backport.

Signed-off-by: Russell King <linux@armlinux.org.uk>
2020-05-21 12:55:31 +02:00
Thibaut VARÈNE
6934b20912 generic: platform/mikrotik: disambiguate SPDX-License-Identifier
I meant it to be GPL-2.0-only, as evidenced by the boilerplate.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-20 17:03:45 +02:00
Thibaut VARÈNE
49eec56bfc generic: routerbootpart.c: disambiguate SPDX-License-Identifier
I meant it to be GPL-2.0-only, as evidenced by the boilerplate.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-20 17:03:45 +02:00
Petr Štetiar
1b2fefb244 kernel: bump 5.4 to 5.4.42
Refreshed patches, removed upstreamed patch:

 generic/pending: 001-v5.4-pinctrl-qcom-fix-wrong-write-in-update_dual_edge.patch.patch

Run tested: qemu-x86-64
Build tested: x86/64, ath79/nand, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-20 15:26:22 +02:00
Alberto Bursi
dc7cc60ca3 x86: fix generic kernel 5.4 config
The last kernel update done with commit 500a02bc29 ("x86: Update
configuration") placed most of the updated config only in the x86_64
target.

Move the options needed by the other targets too in the x86 base config,
and add an additional option needed by those targets.

Fixes: 500a02bc29 ("x86: Update configuration")
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
[commit subject/description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-20 15:26:22 +02:00
Richard Huynh
f3792690c4 ramips: Add support for Xiaomi Redmi Router AC2100 (RM2100)
Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot

Installation:

1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0

Restore to stock:

1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white

Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.

Exploit and detailed instructions:

https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100

An implementation of CVE-2020-8597 against stock firmware version 1.0.14

This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.

As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.

The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh

Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
2020-05-20 15:26:22 +02:00
Álvaro Fernández Rojas
c93cdf536a bcm63xx: lzma-loader: rely on CHIP_ID for UART address
lzma-loader uart output wasn't working on BCM3380/BCM6362 because these
SoCs have the same processor ID.
Let's use CHIP_ID for establishing the UART base address.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-20 11:15:29 +02:00
Álvaro Fernández Rojas
8e8920c92f bcm63xx: lzma-loader: remove unused definitions
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-20 09:26:15 +02:00
Álvaro Fernández Rojas
0836e22a83 bcm63xx: image: add CVG834G CHIP_ID
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-20 09:23:10 +02:00
Álvaro Fernández Rojas
91b275b6e3 bcm63xx: image: rename CFE_CHIP_ID to CHIP_ID
Rename CFE_CHIP_ID to a generic name that doesn't involve CFE.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-20 09:21:34 +02:00
Álvaro Fernández Rojas
e0382c50e9 bcm63xx: fix AD1018 WLAN led
Standard AD1018 has lower case LEDs.

Fixes: 5f82691923 ("bcm63xx: add unmodded SERCOMM AD1018 support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-20 08:46:13 +02:00
Álvaro Fernández Rojas
5f82691923 bcm63xx: add unmodded SERCOMM AD1018 support
Until now only HW modded SPI flash version was supported.

BCM6328 with 64M RAM and 128M NAND.
More info: https://openwrt.org/toh/sercomm/ad1018

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 13:33:39 +02:00
Álvaro Fernández Rojas
5d3bb7ea9a kernel: mtdsplit: bcm_wfi: add sercomm support
SERCOMM creates separates partitions for cferam.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 13:33:39 +02:00
Álvaro Fernández Rojas
f996377a26 bcm63xx: bcm6328: fix strapbus boot sel
Boot selection bit is 18, not 28.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 13:33:39 +02:00
Sungbo Eo
31697f92a2 ramips: fix MAC address setup for RT5350F-OLinuXino devices
Olimex RT5350F-OLinuXino devices do not have a default MAC address, and there is
nothing at the 0x4 offset in the factory partition. Using a local address, which
is randomly generated by the kernel, would be a better choice.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-19 19:03:07 +08:00
Sungbo Eo
f7112a180f ramips: 5.4: handle ERR_PTR properly
of_get_mac_address can return ERR_PTR since 5.2, so the return pointer should be
checked before used. Otherwise it might cause an oops during boot.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-19 19:03:07 +08:00
INAGAKI Hiroshi
0a05d71f6f ramips: fix initramfs image for I-O DATA mt7621 devices
This is additional fix of c998ae7f0e.

The sysupgrade image of I-O DATA MT7621 devices manufactured by MSTC
(MitraStar Technology Corp.) faced to the booting issue. This was caused
by imcomplete extraction of large kernel image by U-Boot, and this issue
is occurred in initramfs image after fixing of sysupgrade image.
So, use lzma-loader for initramfs image to fix the issue.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
2020-05-19 19:03:07 +08:00
Chuanhong Guo
a43cbfe2e3 ramips: remove default switch setup in 02_network
ramips images now relies on explicit switch setup for proper failsafe
functionality. Remove default cases where it relies on vlan setup in
dts and add switch setup for devices affected.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-05-19 19:03:02 +08:00
Álvaro Fernández Rojas
597df570f3 bcm63xx: reorganize board patches
Let's put some order on board patches.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 11:07:24 +02:00
Álvaro Fernández Rojas
edafbe81e0 bcm63xx: bcm6328-leds: improve HW blinking
Add support for second HW blinking interval.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 11:03:58 +02:00
Álvaro Fernández Rojas
daee6b4661 bcm63xx: add Comtrend VG-8050 support
BCM63169 with 128M RAM, 128M NAND and BCM53125 switch.
Switch is connected by HSSPI to CS5.
More info: https://openwrt.org/toh/comtrend/vg8050

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 10:41:47 +02:00
Álvaro Fernández Rojas
62e7342ddf bcm63xx: add NETGEAR DGND3700v2 support
BCM6362 with 64M RAM, 32M NAND and BCM53125 switch.
Switch is connected by MMAP, which is currently unsupported (no VLANs).
More info: https://openwrt.org/toh/netgear/dgnd3700v2

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 10:41:42 +02:00
Adrian Schmutzler
74ff0773b5 ramips: remove leading zeros from MAC address location
Cosmetic adjustment to match the rest of the target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Adrian Schmutzler
be9eab9bca ramips: set WAN address in DTS for ASUS RT-AC51U/RT-AC54U
The location 0x28 in factory partition is the common one used for
ethernet address on this architecture. Despite, it contains the label
MAC address for the devices at hand.

Consequently, this patch moves 0x28 to the &ethernet node in DTS files
(setting the WAN MAC address there) and sets up the lan_mac from 0x22
in 02_network. As a benefit, this allows to use label-mac-device in
DTS instead of ucidef_set_label_macaddr.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Adrian Schmutzler
a1f0fd8cba ramips: use DT trigger for 2G WiFi on ASUS RT-AC51U
Like for the RT-AC54U, this uses a DT trigger for WiFi also at the
RT-AC51U. While at it, rename node and label to wifi2g.

Note that the 5g WiFi LED still isn't supported (see PR #3017 for
further details: https://github.com/openwrt/openwrt/pull/3017 )

Tested-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Adrian Schmutzler
0b34a36da9 ramips: fix MAC address assignment for ASUS RT-AC51U
The current MAC address assignment for the ASUS RT-AC51U is "wrong",
it actually should be the same as for the RT-AC54U. Fix it.

MAC assignment based on vendor firmware:

  2g    0x4	label
  5g    0x8004	label +4
  lan   0x22	label +4
  wan   0x28	label

Thanks to Davide Fioravanti for checking this on his device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Fabian Bläse
33b2078528 mt7621: Make ER-X-SFP factory image compatible with EP-R6
The version inside the compat file determines, if a firmware supports
a specific device. I have not yet fully understood, how this is checked,
but it only seems to indicate which devices are supported by a specific
version of the combined vendor firmware. Devices assume that subsequent
versions, starting with the version that initially added support for a
specific device, are always compatible.

The first compat version that added support for the EP-R6 was '21001:7',
but OpenWrt did use '21001:6' before. This is why the factory image could
not be flashed using the vendor software, but only using TFTP.

The compat version has been bumped by the vendor a few times, but more
devices have been added since (e.g. ER-10X). Because OpenWrt currently
only supports the ER-X, ER-X-SFP and EP-R6, the compat version is
incremented to the version that first supported the EP-R6, which is
'21001:7'.

This allows the factory image to be flashed on EP-R6 without TFTP.

Signed-off-by: Fabian Bläse <fabian@blaese.de>
2020-05-18 21:11:47 +02:00
David Bauer
4133304413 mpc85xx: restructure image receipts
Move the image receipts into separate per-subtarget files like it is
done on most other targets.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-18 21:11:39 +02:00
David Bauer
564f87ef5b mpc85xx: rename generic subtarget to p1010
The mpc85xx-generic subtarget supports the QorIQ SoCs of the p1010
family. Rename the subtarget to reflect this affiliation as it's the
case with the other mpc85xx subtargets.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-18 21:11:22 +02:00
Álvaro Fernández Rojas
367a30389d bcm63xx: add support for Comtrend VR-3032u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Álvaro Fernández Rojas
86583384ff bcm63xx: smp: add NAND support
NAND controller is present on BCM6328, BCM6362, BCM6368 and BCM63268.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Álvaro Fernández Rojas
cca13d8e82 kernel: mtdsplit: add BCM WFI support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Adrian Schmutzler
4a61a88f90 ath79: add support for TP-Link TL-WA901ND v4 and v5
This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79.
They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6.

Specifications:
  SoC: TP9343
  Flash/RAM: 4/32 MiB
  CPU: 750 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

Flash instruction (TFTP):
  1. Set PC to fixed ip address 192.168.0.66
  2. Download *-factory.bin image and rename it to * (see below)
  3. Start a tftp server with the image file in its root directory
  4. Turn off the router
  5. Press and hold Reset button
  6. Turn on router with the reset button pressed and wait ~15 seconds
  7. Release the reset button and after a short time
     the firmware should be transferred from the tftp server
  8. Wait ~30 second to complete recovery.

  * The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for
  both variants.

In ar71xx, a MAC address with offset 1 was used for ethernet port.
That's probably wrong, but this commit sticks to it until we know
the correct value.

Like in ar71xx, this builds the default factory.bin with EU country
code.

Thanks to Leonardo Weiss for testing on the v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 13:35:38 +02:00
Alexander Couzens
bf5d800578
lantiq: fritz 7360 v2: remove additional supported devices
The additional supported device isn't required since this is a new
device. Some board contains an addtional device,
those device were supported in earlier versions which used the
"old" image builder code.
To support an sysupgrade from such old version, there is the all caps
additional device.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:59:22 +02:00
Alexander Couzens
0962baae4e lantiq: fritz 7360 v2: rename device before it will be used
Use similiar naming scheme as ath79.
Since the fritz 7360 v2 was only in the tree for 2 days, there
is no compatibility for the old image.
Users which has installed the fritz 7360 v2 before this change, must
use sysupgrade --force to skip checks on the board.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:57:57 +02:00
Adrian Schmutzler
30cc7f3510 ramips: increase SPI frequency for ASUS RT-AC51U/RT-AC54U
This increases the SPI frequency for both ASUS RT-AC51U and RT-AC54U.

Speed comparison tests have been performed on RT-AC54U:

- 10Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    4m 37.78s
user    0m 0.02s
sys     2m 43.92s

- 50Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 28.34s
user    0m 0.03s
sys     0m 46.96s

- 50Mhz fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 11.94s
user    0m 0.01s
sys     0m 46.94s

- 80Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 12.31s
user    0m 0.04s
sys     0m 46.96s

- 80Mhz fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 12.15s
user    0m 0.02s
sys     0m 46.97s

Based on that, we took 50 MHz with fast-read, as higher frequencies
didn't yield further improvements.

For the RT-AC51U, only the final configuration was tested.

Tested-by: Zhijun You <hujy652@gmail.com> [RT-AC54U]
Tested-by: Davide Fioravanti <pantanastyle@gmail.com> [RT-AC51U]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:38:22 +02:00
Álvaro Fernández Rojas
13c33f3f12 bcm63xx: mask interrupts on init
Fixes BCM6348/BCM6358 hangs while booting:
https://bugs.openwrt.org/index.php?do=details&task_id=2202

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-17 23:29:48 +02:00
Roger Pueyo Centelles
a0ef42e77c ath79: add support for Ubiquiti PowerBeam 5AC 500
The Ubiquiti PowerBeam 5AC 500 (PBE-5AC-500) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna.

Specifications:
 - SoC: Qualcomm Atheros QCA9558
 - RAM: 128 MB DDR2
 - Flash: 16 MB SPI NOR (mx25l12805d)
 - Ethernet: 1x 10/100/1000 Mbps Atheros 8031, 24 Vdc PoE-in
 - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
 - Buttons: 1x (reset)
 - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue
 - UART: not tested

Not supported:
 - RSSI LEDs (probably through 74HC595 chip)

Installation from stock airOS firmware:
 - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at
   https://openwrt.org/toh/ubiquiti/common

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-05-17 21:03:30 +02:00
Davide Fioravanti
31b49f02ca ramips: add support for Linksys EA7500 v2
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH:   5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615N (4x4:4)
  - 5GHz:   1x MT7615N (4x4:4)
  - 4 antennas: 3 external detachable antennas and 1 internal
USB:
  - 1x USB 3.0
  - 1x USB 2.0
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x White led (Power)
  - 6x Green leds (link lan1-lan4, link wan, wps)
  - 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)

Everything works correctly.

Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.

However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).

After this, you should be back in the OEM firmware.

Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).

When the router reboots flash the “factory” OpenWrt image and this
time it should work.

After the OpenWrt installation you have to use the sysupgrade image
for future updates.

Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.

Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
 1) "kernel" and "rootfs"
 2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.

This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.

A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.

Another way to switch the boot partition is:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.

Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.

However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.

If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
2020-05-17 18:44:28 +02:00
Sungbo Eo
a4e9c8f14b ramips: add support for netis WF2770
netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- UART:
  - J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-17 18:41:48 +02:00
Zhijun You
46674723e1 ramips: add support for ASUS RT-AC54U
Specification:

- CPU: MTK MT7620A
- RAM: 64MB
- ROM: 16MB SPI Flash Macronix MX25L12835E
- WiFi1: MediaTek MT7620A
- WiFi2: MediaTek MT7612E
- Button: reset, wps
- LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN
- Ethernet: 5 ports, 4 LAN + 1 WAN
- Other: 1x UART 1x USB2.0

Installation:

   Update using ASUS Firmware Restoration Tool:

1. Download the ASUS Firmware Restoration Tool but don't open it yet
2. Unplug your computer from the router
3. Put the router into Rescue Mode by: turning the power off, using a pin
   to press and hold the reset button, then turning the router back on while
   keeping the reset button pressed for ~5 secs until the power LED starts
   flashing slowly (which indicates the router has entered Rescue Mode)
4. Important (if you don't do this next step the Asus Firmware
   Restoration Tool will wrongly assume that the router is not in Rescue Mode
   and will refuse to flash it): go to the Windows Control Panel and
   temporarily disable ALL other network adapters except the one you will use
   to connect your computer to the router
5. For the single adapter you left enabled, temporarily give it the
   static IP 192.168.1.10 and the subnet mask 255.255.255.0
6. Connect a LAN cable between your computer (make sure to use the
   Ethernet port of the adapter you've just set up) and port 1 of the router
   (not the router's WAN port)
7. Rename sysupgrade.bin to factory.trx
8. Open the Asus Firmware Restoration Tool, locate factory.trx and click
   upload (if Windows shows a compatibility prompt, confirm that the tool worked fine)
9. Flashing and reboot is finished when the power LED stops blinking and
   stays on

MAC assignment based on vendor firmware:

2g    0x4	label
5g    0x8004	label +4
lan   0x22	label +4
wan   0x28	label

Signed-off-by: Zhijun You <hujy652@gmail.com>
[rebased due to DTSI patch, minor commit message adjustments, fix
label MAC address (lan->wan), do spi frequency increase separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:40:56 +02:00
Adrian Schmutzler
685cc66c2a ramips: create DTSI for ASUS RT-AC51U and RT-AC54U
This creates a DTSI for the ASUS RT-AC51U and the upcoming RT-AC54U,
as they are quite similar.

White at it, drop the unneeded "status = okay" for ethernet.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:39:48 +02:00
Adrian Schmutzler
b24fd13024 lantiq: drop outdated kernel version switches from patches-5.4
This drops some ancient kernel version switches from patches on
lantiq target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:36:21 +02:00
Adrian Schmutzler
41b5ca1458 bcm27xx: drop outdated kernel version switches from patches-5.4
This drops some ancient kernel version switches from patches on
bcm27xx target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.

Refresh remaining target patches.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:36:10 +02:00
Adrian Schmutzler
8ff813e5f4 generic: drop outdated kernel version switches in local drivers
This drops the obsolete version switches for non-supported kernels
from local drivers in generic target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:35:59 +02:00
Adrian Schmutzler
c00b2df6c8 ramips: drop non-existant ralink,port-map for Ravpower WD03
The property "ralink,port-map" has been obsolete long before
this device was added, and the device is a one-port anyway.
Just remove it.

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:34:40 +02:00
Adrian Schmutzler
d7a28e8ed2 ramips: mt7620: tidy up ethernet node in DTS files
This tidies up the ethernet node in mt7620 DTS files by:

- removing unnecessary status as it is not disabled
- reordering properties consistently
- adding empty lines to enhance readability

This should make comparison and reviewing new PRs based on C/P easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:28:03 +02:00
Thibaut VARÈNE
2ea481193c generic: platform/mikrotik: fix LZOR support
31e99fe3da which introduced this code was unfortunately untested.
This commit fixes a number of issues and works around the fact that in
this particular scheme, the LZO payload may be padded at the end which
will trigger a harmless lzo decompression error.
This commit also disambiguates the debug printks.

Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 31e99fe3da ("generic: platform/mikrotik: support LZOR encoding")
2020-05-16 20:30:46 +02:00
Yushi Nishida
78bebe680f
lantiq/xrx200: add support for the Fritzbox 7360v2
This commit adds support for the Fritzbox 7360v2

CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A

DECT is not working.

Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.

Firmware can be flashed with this method:

1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
    via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:

passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin

5.) wait till red light flashing turns off.
6.) type: exit

Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.

Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)

Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
2020-05-16 04:37:55 +02:00
Aleksander Jan Bajkowski
2f7118712e ath79: increase spi frequency on tp-link tl-wr1043nd v2
Increase SPI frequency to 33.333 MHz. It's maximum frequency supported
by SPI Flash memory chip without Fast read opcode.

Before:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 3.21s
user	0m 0.00s
sys	0m 3.21s

After:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 2.52s
user	0m 0.00s
sys	0m 2.52s

Tested on TP-Link TL-WR1043ND V2.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-05-15 10:00:32 +08:00
Daniel Gonzalez Cabanelas
e04ff3c7cc bcm63xx: periph_intc: report effective affinity
The bcm6345-periph-intc driver only targets a single CPU at a time, even
if the notional affinity is wider. Let's inform the core code about this.

This patch gets rid of the kernel message:
"genirq: irq_chip bcm6345-periph-intc did not update eff. affinity mask
of irq 52"

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2020-05-14 18:10:12 +02:00
Álvaro Fernández Rojas
29c3bb5f41 bcm63xx: ext_intc: fix warning
In file included from ./arch/mips/include/asm/io.h:34,
                 from ./arch/mips/include/asm/mmiowb.h:5,
                 from ./include/linux/spinlock.h:60,
                 from ./include/linux/irq.h:14,
                 from drivers/irqchip/irq-bcm6345-ext.c:10:
drivers/irqchip/irq-bcm6345-ext.c: In function 'bcm6345_ext_intc_of_init':
./arch/mips/include/asm/mach-bcm63xx/ioremap.h:48:9: warning: 'base' may be used uninitialized in this function [-Wmaybe-uninitialized]
  return is_bcm63xx_internal_registers((unsigned long)addr);
         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-bcm6345-ext.c:255:16: note: 'base' was declared here
  void __iomem *base;
                ^~~~

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:28:31 +02:00
Álvaro Fernández Rojas
f2f2cf07a6 bcm63xx: periph_intc: fix warning
drivers/irqchip/irq-bcm6345-periph.c: In function 'bcm6345_periph_irq_handle':
drivers/irqchip/irq-bcm6345-periph.c:55:21: warning: 'block' may be used uninitialized in this function [-Wmaybe-uninitialized]
  struct intc_block *block;
                     ^~~~~

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:27:31 +02:00
Álvaro Fernández Rojas
f314cbe54b bcm63xx: redboot: fix warning
drivers/mtd/parsers/redboot.c: In function 'parse_redboot_partitions':
drivers/mtd/parsers/redboot.c:194:59: warning: suggest parentheses around '-' in operand of '&' [-Wparentheses]
     fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
                                       ~~~~~~~~~~~~~~~~~~~~^~~

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:12 +02:00
Álvaro Fernández Rojas
ee6bf7e865 bcm63xx: bcm6362: fix pinctrl bug
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:12 +02:00
Álvaro Fernández Rojas
aa2f2276f7 bcm63xx: image: remove unused definition
KERNEL_ENTRY isn't used by lzma-loader.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:08 +02:00
Álvaro Fernández Rojas
eea23c2004 bcm63xx: remove linux 4.14 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 14:52:54 +02:00
Koen Vandeputte
eb17ee294c kernel: bump 5.4 to 5.4.41
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-14 13:33:40 +02:00
Koen Vandeputte
d503492857 kernel: bump 4.19 to 4.19.123
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-14 13:33:40 +02:00
Adrian Schmutzler
2308644b0c ipq40xx: replace "ok" with "okay" for status in DTS files
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 19:16:41 +02:00
Adrian Schmutzler
fdd968d64e bcm63xx: replace "ok" with "okay" for status in DTS files
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 16:59:04 +02:00
Adrian Schmutzler
026fe1308c bcm63xx: use generic diag.sh
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.

Though generic diag.sh allows to use different LEDs to indicate different
states, this patch just moves the old assignment and does not try to
"improve" the assignment by using additional colors.
However, individual proposals to do so are welcome.

For the few cases where status_led2 was used in old diag.sh, only the
primary LED was migrated.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 16:57:45 +02:00
Thibaut VARÈNE
96414047c9 ar71xx: mikrotik: mach-rbspi.c remove wlan id
Following on the previous commit, this patch removes useless id argument
from rbspi_wlan_init().

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:41:12 +02:00
Thibaut VARÈNE
1c6990fe6d ar71xx: mikrotik: bypass id check in __rb_get_wlan_data()
The id parameter in __rb_get_wlan_data() was incorrectly used on the
assumption that id "0" would always be tied to ath9k with RLE encoding
and positive id (in fact, only id "1" was valid) would always be tied to
("external") ath10k with LZO encoding.

Newer hardware revisions of supported devices prove this assumption to
be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO
compressed, so disable this check to allow newer hardware to correctly
decode caldata for ath9k. Since ath10k caldata is no longer pulled from
this implementation, this commit also disables the publication in sysfs
to avoid wasting memory.

Note: this patch assumes that ath9k caldata is never stored with the new
"LZOR" encoding scheme found on some ath10k devices.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:41:08 +02:00
Koen Vandeputte
0fed36dd48 kernel: bump 5.4 to 5.4.40
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Koen Vandeputte
7dd2d7289a kernel: bump 4.19 to 4.19.122
Refreshed all patches.

Remove upstreamed:
- 551-loop-Better-discard-support-for-block-devices.patch

Fixed:
- CVE-2020-11884
- CVE-2020-12114
- CVE-2019-3016
- CVE-2020-11669

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Koen Vandeputte
ef2d5a2ab4 kernel: bump 4.14 to 4.14.180
Refreshed all patches.

Fixes:
- CVE-2020-12114
- CVE-2020-11669

Compile-tested on: pistachio
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Álvaro Fernández Rojas
a0081b1945 bcm63xx: loader-lzma: use default lzma
Specific CFE LZMA parameters aren't needed for LZMA Loader.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-12 12:34:57 +02:00
Álvaro Fernández Rojas
84646936a6 bcm63xx: image: rename LOADADDR to KERNEL_LOADADDR
Also remove KERNEL_ENTRY, since it's the same as KERNEL_LOADADDR

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-12 12:34:57 +02:00
Koen Vandeputte
146e18af56 generic: add MikroTik hw bit description
An e-mail response from MikroTik contained a minimal overview
on hardware option bits which mentioned a currently unknown bit.

While not being too detailed what it does, add it for documentation purposes.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-11 16:49:04 +02:00
David Bauer
300b7fe85a ipq40xx: add support for Aruba AP-365
Hardware
--------
SoC:   Qualcomm IPQ4029
RAM:   512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
       - 4MB SPI-NOR (Macronix MX25R3235F)
TPM:   Atmel AT97SC3203
BLE:   Texas Instruments CC2540T
       attached to ttyMSM0
ETH:   Atheros AR8035
LED:   System (red / green / amber)
BTN:   Reset

The USB port on the device is (in contrast to other Aruba boards) real
USB. The AP uses a CP2101 USB TTY converter on the board.

Console baudrate is 9600 8n1.

To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.

Installation
------------

1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
   into the TFTP server root directory. Configure the TFTP server to
   be reachable at 192.168.1.75/24. Connect the machine running the TFTP
   server to the ethernet port of the access point.

2. Connect to the serial console. Interrupt autobooting by pressing
   Enter when prompted.

3. Configure the bootargs and bootcmd for OpenWrt.
   $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
   $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
     ubi read 0x85000000 kernel; bootm 0x85000000"
   $ setenv ramboot_openwrt "run bootargs_openwrt;
     setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
     netget; set fdt_high 0x87000000; bootm"
   $ setenv bootcmd "run nandboot_openwrt"
   $ saveenv

4. Load OpenWrt into RAM:
   $ run ramboot_openwrt

5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
   /tmp folder on the device.

6. Flash OpenWrt:
   Make sure you use the mtd partition with the label "ubi" here!

   $ ubidetach -p /dev/mtd1
   $ ubiformat /dev/mtd1
   $ sysupgrade -n /tmp/openwrt-sysupgrade.bin

To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:

  $ setenv bootcmd "boot"
  $ saveenv

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-11 01:05:16 +02:00
Andrey Kunitsyn
e31e5c4ea4 bcm27xx: label to boot partition
Get fat partition name allow easy partition identification
for user.

Signed-off-by: Andrey Kunitsyn <blackicebox@gmail.com>
2020-05-10 17:06:27 +02:00
Pawel Dembicki
426fb8cf84 ramips: add support for LB-Link BL-W1200
The BL-W1200 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612E)
- 5x 10/100/1000 Mbps Ethernet (MT7530)
- 2x external, non-detachable antennas (Wifi 2.4G/5G)
- 1x USB 2.0
- UART (R2) on PCB (57600 8n1)
- 9x LED (1 GPIO controlled), 1x button
- u-Boot bootloader

Known issues:
- No status LED. Used WPS LED during boot/failsafe/sysupgrade.

Installation:
1. Apply initramfs image via factory web-gui.
2. Install sysupgrade image.

How to revert to OEM firmware:
- sysupgrade -n -F stock_firmware.bin

Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-05-09 20:02:17 +02:00
Sungbo Eo
0cdf7bc4fb ramips: dts: fix incorrect flash reg property
Most work was done in commit 021c893658 ("ramips: fix size-cells on spi
nodes"), but a few more DTS files using the old reg style have been added
since then. This commit fixes them.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-09 14:49:33 +02:00
Sungbo Eo
1eceab3fc0 ramips: dts: use generic node name for flash
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

While at it, remove unused m25p80 label.

Tested on rt5350 (for spi-nor) and rt3662 (for cfi-flash).

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-09 14:48:50 +02:00
Jakov Petrina
b1cfbff0a7 mvebu: uDPU: switch default kernel and U-Boot PHY mode
Certain SFP modules (most notably Nokia GPON ones) first check
connectivity on 1000base-x, and switch to 2500base-x afterwards. This
is considered a quirk so the phylink switches the interface to
2500base-x as well.

However, after power-cycling the uDPU device, network interface/SFP module
will not work correctly until the module is re-seated. This patch
resolves this issue by forcing the interface to be brought up in
2500base-x mode by default.

Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2020-05-09 14:34:23 +02:00
Lech Perczak
94f3449977 ath79: dts: add missing 'serial0' alias for TP-Link TL-MR3040v2
Out of all devices currently supported based on AR9331 chipset,
this one had the 'serial0' alias missing. Add it to fix setting of
/dev/console and login shell on the onboard UART.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2020-05-08 19:39:36 +02:00
Sungbo Eo
a5720d3276 ramips: tidy up image subtarget Makefiles
- use tab indent in image build recipes for consistency
- harmonize line wrapping

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[use different line wrapping for one recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-08 18:58:39 +02:00
Sungbo Eo
c5fdab84ed ramips: tidy up image Makefile
- sort recipes alphabetically
- simplify subtarget include directives

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-08 18:53:23 +02:00
Sungbo Eo
fa9e7ca466 ramips: simplify palmbus/{i2c,spi} in device DTS files
As the node is already defined and labeled in SoC DTSI file, we can refer to it
outside of root node and reduce redundancy.

While at it, remove unused pcf8563 label.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-08 18:43:00 +02:00
Sungbo Eo
22a21b0c18 ramips: use hex notation for *-mtd-eeprom property
Change "0" to "0x0" for consistency. This is an extension of commit 34abfb6e91
("ramips: convert mediatek,mtd-eeprom from decimal to hex notation").

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-08 18:34:27 +02:00
Koen Vandeputte
51a7184a7d generic: fix patching error on kernel 5.4
Fixes a build error seen when applying the kernel patches.

Applying patch generic/435-mtd-add-routerbootpart-parser-config.patch
patching file drivers/mtd/parsers/Kconfig
Hunk #1 FAILED at 160.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Kconfig
patching file drivers/mtd/parsers/Makefile
Hunk #1 FAILED at 10.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Makefile

This was missed as 5.4 is currently set as testing kernel
while the main kernel being used is 4.19

Fixes: 2976e423dc ("generic: routerboot partition build bits")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-08 17:06:10 +02:00
Thibaut VARÈNE
5e50515fa6 ramips/mt7621: mikrotik: don't use mtd-mac-address in DTS
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.

Adjust config so that WAN is base MAC and LAN is base MAC +1 to better
match label and vendor OS.

[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:18 +02:00
Thibaut VARÈNE
9242d691ec ath79/mikrotik: load caldata via sysfs loader
This commit takes advantages of base-files 220 which introduces routines
to perform caldata loading directly via the kernel sysfs loader helper.
This has the benefits of not wasting flash space to store caldata.

Memory footprint is reduced to the bare minimum: for devices that don't
need MAC patching, the caldata is loaded directly, for devices that do
need MAC patching, the caldata is extracted to /tmp, patched and then
loaded.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
e995577e70 ar71xx/mikrotik: ath10k: use new sysfs driver
Fetch ath10k calibration data from new mikrotik sysfs driver

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
1e24af5638 ath79/mikrotik: use standard caldata functions
With the implementation of a sysfs interface to access WLAN data, this
target no longer needs a special wrapper to extract caldata.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
301bc3290d ath79/mikrotik: don't use mtd-mac-address in DTS
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.

To match sticker and vendor OS behavior, WAN MAC is set to the device
base MAC and LAN MAC is incremented from that.

Note: this will trigger a harmless kernel message during boot:
ag71xx 19000000.eth: invalid MAC address, using random address

There is no clean workaround to prevent this message from being emitted.

[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
31e99fe3da generic: platform/mikrotik: support LZOR encoding
Some newer MikroTik RouterBOARD devices use a new encoding scheme
for their WLAN calibration data. This patch provides support for
decoding this new scheme.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
97337d3e5d ramips/mt7621: enable mikrotik platform driver
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
00d2ab7602 ar71xx/mikrotik: enable mikrotik platform driver
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
65d5053045 ath79/mikrotik: enable mikrotik platform driver
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
1dcc2249cd generic: mikrotik platform build bits
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
5ecf7d9654 generic: routerboot sysfs platform driver
This driver exposes the data encoded in the "hard_config" flash segment
of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder
named "hard_config". The WLAN calibration data is available on demand via
the 'wlan_data' sysfs file in that folder.

This driver permanently allocates a chunk of RAM as large as the
"hard_config" MTD partition (typically 4KB), although it is technically
possible to operate entirely from the MTD device without using a local
buffer (except when requesting WLAN calibration data), at the cost of a
performance penalty.

This driver does not reuse any of the existing code previously found in
routerboot.c.

This driver has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.

Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
21869e8f80 ramips: mikrotik: use routerbootpart partitions
Enable routerbootpart partitions on MikroTik devices.

Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
274221a836 ramips/mt7621: enable CONFIG_MTD_ROUTERBOOT_PARTS
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
8f90dbfd1f ath79/mikrotik: use routerbootpart partitions
Enable routerbootpart partitions on MikroTik devices.

Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
c8b2ad4185 ath79/mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTS
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
2976e423dc generic: routerboot partition build bits
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
ee5ee99dcf generic: routerbootpart MTD parser for RouterBoot
This driver provides an OF MTD parser to properly assign the RouterBoot
partitions on the flash. This parser builds from the "fixed-partitions"
one (see ofpart.c), but it can handle dynamic partitions as found on
routerboot devices.

The parent node must contain the following:
	compatible = "mikrotik,routerboot-partitions";
	#address-cells = <1>;
	#size-cells = <1>;

Children routerbootpart DTS nodes are defined as follows:
For fixed partitions
	node-name@unit-address {
		reg = <prop-encoded-array>;
		label = <string>;
		read-only;
		lock;
	};

All properties but reg are optional.

For dynamic partitions:
	node-name {
		size = <prop-encoded-array>;
		label = <string>;
		read-only;
		lock;
	};

size property is mandatory unless the next partition is a fixed one or
a "well-known" one (matched from the strings defined below) in which case
it can be omitted or set to 0; other properties are optional.

By default dynamic partitions are appended after the preceding one, except
for "well-known" ones which are automatically located on flash.

Well-known partitions (matched via label or node-name):
 - "hard_config"
 - "soft_config"
 - "dtb_config"

This parser requires the DTS to list partitions in ascending order as
expected on the MTD device.

This parser has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.

Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Stijn Tintel
03fd38d612 kernel: add missing symbol to 5.4 config
This symbol is exposed if KERNEL_PROVE_LOCKING is enabled.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-05-08 05:56:36 +03:00
Rosen Penev
73fa1aba94 samba36: Remove
Samba 3.6 is completely unsupported, in addition to having tons of patches

It also causes kernel panics on some platforms when sendfile is enabled.
Example:

https://github.com/gnubee-git/GnuBee_Docs/issues/45

I have reproduced on ramips as well as mvebu in the past.

Samba 4 is an alternative available in the packages repo.

cifsd is a lightweight alternative available in the packages repo. It is
also a faster alternative to both Samba versions (lower CPU usage). It
was renamed to ksmbd.

To summarize, here are the alternatives:
- ksmbd + luci-app-cifsd
- samba4 + luci-app-samba4

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[drop samba36-server from GEMINI_NAS_PACKAGES, ksmbd rename + summary]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-05-08 03:32:52 +03:00
Yangbo Lu
70a6a98149 layerscape: define only one package for ls-dpl
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-dpl with only one package
installing all 4 files as intermediate files.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
2e61c4ac1f layerscape: define only one package for ls-mc
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-mc with only one package
installing all two images as intermediate files.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
6c9d8990a4 layerscape: define only one package for fman-ucode
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain fman-ucode with only one package
installing all two binaries as intermediate files.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
084c82c5b0 layerscape: define only one package for ls-rcw
We do not have to define package for each board, and
consider variant's building/installing.
It is easier to maintain ls-rcw with only one package
installing all boards RCW binaries as intermediate
files, each of which is just about hundreds of bytes.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
e12ec82e44 layerscape: switch to kernel 5.4
Switch to kernel 5.4 in Makefile.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
670684d9d4 layerscape: disable UEFI runtime support in config-5.4
Disable CONFIG_EFI (UEFI runtime support) in config-5.4,
while is not required.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
7a08169dc1 layerscape: re-enable IFC NAND/NOR controllers in config-5.4
The Freescale IFC NAND/NOR controllers options were disabled
in default in previous running make kernel_oldconfig.
So re-enable them.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
f3476e5be6 layerscape: refresh kernel 5.4 config
By running make kernel_oldconfig and selecting relevant options.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
a812ebafa1 layerscape: copy kernel config from 4.14 to 5.4
Just copy kernel config from 4.14 to 5.4.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
cddd459140 layerscape: add patches-5.4
Add patches for linux-5.4. The patches are from NXP LSDK-20.04 release
which was tagged LSDK-20.04-V5.4.
https://source.codeaurora.org/external/qoriq/qoriq-components/linux/

For boards LS1021A-IOT, and Traverse-LS1043 which are not involved in
LSDK, port the dts patches from 4.14.

The patches are sorted into the following categories:
  301-arch-xxxx
  302-dts-xxxx
  303-core-xxxx
  701-net-xxxx
  801-audio-xxxx
  802-can-xxxx
  803-clock-xxxx
  804-crypto-xxxx
  805-display-xxxx
  806-dma-xxxx
  807-gpio-xxxx
  808-i2c-xxxx
  809-jailhouse-xxxx
  810-keys-xxxx
  811-kvm-xxxx
  812-pcie-xxxx
  813-pm-xxxx
  814-qe-xxxx
  815-sata-xxxx
  816-sdhc-xxxx
  817-spi-xxxx
  818-thermal-xxxx
  819-uart-xxxx
  820-usb-xxxx
  821-vfio-xxxx

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Petr Štetiar
d1d2c0b557 kernel: bump 5.4 to 5.4.39
Refreshed patches.

Run tested: qemu-x86-64
Build tested: x86/64, imx6, sunxi/a53, layerscape/armv7+armv8_64b

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-07 12:53:06 +02:00
Chuanhong Guo
47f17b0662 generic: ar8216: fix unknown packet flooding for ar8229/ar8236
ar8229 and ar8236 don't allow unknown unicast/multicast frames and
broadcast frames to be flooded to cpu port. This isn't desired behavior
for swconfig as we treat it as a standalone switch.
Current code doesn't enable unicast frame flooding for ar8229 and uses
wrong setup for ar8236. This commit fixes both of them by enabling port
0 flooding for all unknown frames.

Fixes: FS#2848
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-05-06 08:59:27 +08:00
Adrian Schmutzler
0fb5962e62 sunxi: remove unneeded shebang for preinit files
preinit files are sourced and they have no execute bit set, so remove
their shebang.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-05 13:09:19 +02:00
Adrian Schmutzler
755790808c sunxi: tidy up cases in base-files
This removes unnecessary quotes in cases and applies alphabetic
order to members.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-05 13:06:26 +02:00
Petr Štetiar
73de205c57 kernel: bump 5.4 to 5.4.38
Refreshed patches.

Run tested: qemu-x86-64, apalis
Build tested: x86/64, ipq40xx, ath79, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-04 21:09:12 +02:00
John Crispin
220f43e0f2 mediatek: fix image building
Signed-off-by: John Crispin <john@phrozen.org>
2020-05-04 16:28:46 +02:00
John Crispin
abb0452cd8 mediatek: update patches
Signed-off-by: John Crispin <john@phrozen.org>
2020-05-04 16:27:30 +02:00
Stijn Tintel
49ab97ca86 bcm27xx: backup /boot/cmdline.txt and restore early
If you want to use the Raspberry Pi UART, "console=serial0,115200" needs
to be removed from the kernel cmdline. This is done by editing
/boot/cmdline.txt. However, this file is not currently backed up during
sysupgrade, so this effectively breaks HATs that require the use of the
UART every sysupgrade.

Backup this file during sysupgrade, and restore it before rebooting.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-05-03 17:30:45 +03:00
Petr Štetiar
5ea3ea154f kernel: bump 5.4 to 5.4.36
Refreshed patches, removed upstreamed patch:

 generic/hack: 551-loop-Better-discard-support-for-block-devices.patch

Added generic config symbol `ARM64_ERRATUM_1542419` due to Fixes:
f2791551cedb ("arm64: errata: Hide CTR_EL0.DIC on systems affected by
Neoverse-N1 #1542419").

Run tested: qemu-x86-64, apalis, nbg6617
Build tested: x86/64, imx6, ipq40xx, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-30 00:52:04 +02:00
Daniel Golle
aa0526b5f2 ath79: fix dts of Teltonika RUT9xx devices
The previous commits were missing a semicolon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 22:59:23 +01:00
Daniel Golle
aa4a33ac62 ath79: add support for Teltonika RUT955 H7V3C0
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.

To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector

Serial console (/dev/ttyS0) pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 21:32:35 +01:00
Daniel Golle
c8b309b53d ath79: split Teltonika RUT955 to support other RUT9xx models
Split device-tree of Teltonika RUT955 into a generic RUT9xx part and
a part specific to that version of RUT955 already supported.
Also harmonize GPIO and LED names with what is used by the vendor
firmware and assign RS485 DTR signal.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 21:32:35 +01:00
Adrian Schmutzler
d9ff499671 kirkwood: disable image for Linksys EA3500 (Audi)
Due to the switch to DSA, the kernel image has become too big (2641k) for the
kernel partition (2624k) on this device:

  WARNING: Image file [...]/linux-kirkwood/linksys_audi-uImage is too big

Disable the device until this is fixed, so buildbots can continue their work.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-29 18:04:16 +02:00
Adrian Schmutzler
522f6b7eee ath79: add SUPPORTED_DEVICES based on ar71xx for some devices
This adds some still-missing board names for old TP-Link devices
to ath79 SUPPORTED_DEVICES.

Fixes: FS#3017

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 20:28:06 +02:00
Adrian Schmutzler
03e742dcd8 Revert "ramips: explicitly disable built-in switch for lan-only devices"
This reverts commit a1693bf626.

The rt288x and rt3883 devices in question don't have switches.
Only keep the merged case for rt305x.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 16:53:29 +02:00
Adrian Schmutzler
8b373892d3 kirkwood: remove support for kernel 4.19
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19
support broken on the affected devices.
Support on kernel 5.4 seems to have been running fine for almost 2 months
on multiple devices, while support for 4.19 has never left testing state.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-28 16:50:20 +02:00
Adrian Schmutzler
0af2c44604 kirkwood: remove support for kernel 4.14
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19
support broken on the affected devices.
Support on kernel 5.4 seems to have been running fine for almost 2 months
on multiple devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-28 16:49:31 +02:00
Pawel Dembicki
4fd7e539e4 kirkwood: switch from swconfig to dsa
This patch removes support for swconfig and switches to dsa driver.

swconfig and switch drivers are removed. DSA driver is enabled and
configuration is adjusted.

In kirkwood only two devices have switches: Linksys EA3500 and EA4500.

WAN MAC configuration in 02_network is required because otherwise WAN
would have the same MAC address as lan interfaces. In swconfig solution
the WAN address was assigned in u-Boot to eth1. Now, as eth1 is disabled
and wan is part of the switch, we have to set it manually.

Compile tested: EA3500, EA4500
Run tested: EA4500

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[minor commit title/message adjustments, remove swconfig package
for devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 16:49:31 +02:00
DENG Qingfang
a10537f674 ramips: fix MikroTik 750Gr3 ports MAC addresses
According to a user in OpenWrt forum, on RouterOS the MAC addresses are
ether1(WAN) = MAC
ether2(LAN2) = MAC+1
ether3(LAN3) = MAC+2
etc.

Fix the MAC addresses in OpenWrt.

Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[remove label_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 10:57:17 +02:00
Álvaro Fernández Rojas
2e5e9b459e ath10k-ct-firmware: rename ct-htt packages
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-28 09:33:09 +02:00
Andre Heider
87c909e969 omap: remove support for kernel 4.14
There's support for 5.4 and 4.19 now, remove the 3rd option.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-04-28 01:10:48 +02:00
Andre Heider
1e3ee247be omap: switch to kernel 5.4
Runtime tested on beagleblack.

Signed-off-by: Andre Heider <a.heider@gmail.com>
[added test comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 01:10:42 +02:00
Andre Heider
d20cfa2bd3 omap: make kernel_oldconfig
Attempt to keep the same nand/sound/panel functionality using new knobs.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-04-28 01:10:37 +02:00
Andre Heider
75f7f7eee9 omap: copy kernel 4.19 config for 5.4
Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-04-28 01:10:33 +02:00
Adrian Schmutzler
80a094aaf3 ath79: indicate boot/failsafe/upgrade for NanoBeam/Nanostation AC
Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can
be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC
and Nanostation AC as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:28:51 +02:00
Roger Pueyo Centelles
e210fe91b1 ath79: add support for Ubiquiti PowerBeam 5AC Gen2
The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna. The device is
hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs.

Specifications:
 - SoC: Qualcomm Atheros AR9342 rev 2
 - RAM: 64 MB DDR2
 - Flash: 16 MB SPI NOR (mx25l12805d)
 - Ethernet: 1x 10/100/1000 Mbps Atheros 8035, 24 Vdc PoE-in
 - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
 - WiFi 2.4 GHz: Atheros AR9340 (SoC-based)
 - Buttons: 1x (reset)
 - LEDs: 1x power, 1x Ethernet, 4x RSSI via GPIO. All blue.
 - UART: not tested

Installation from stock airOS firmware:
 - Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[changed device name in commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:17:30 +02:00
Adrian Schmutzler
f0435d5343 ramips: rt3883: remove swconfig from individual DEVICE_PACKAGES
In rt3883 subtarget, several devices add swconfig to their DEVICE_PACKAGES.
This is redundant as the package is already provided via DEFAULT_PACKAGES.

Remove the redundant inclusions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:07:49 +02:00
Adrian Schmutzler
40325abe52 ramips: remove (kmod-)swconfig DEVICE_PACKAGES for Sitecom WL-351
These definitions are not required since swconfig is selected for
the target anyway and kmod-swconfig is pulled as dependency by
kmod-switch-rtl8366rb.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 22:59:40 +02:00
Sungbo Eo
a1693bf626 ramips: explicitly disable built-in switch for lan-only devices
Commit 8f6334eb94 ("ramips: explicitly disable built-in switch when needed")
did not fix rt288x and rt3883 devices. This patch deals with them.

While at it, consolidate duplicate cases in interface setup.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-27 22:54:51 +02:00
Adrian Schmutzler
1553f58a98 ramips: create common definition for I-O DATA NAND devices
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 22:37:23 +02:00
Yong-hyu, Ban
8fdf77878f mediatek: fix compile error caused by upstreamed mtk_m32 function
This fixes following compile error:

```
  CC      drivers/net/ethernet/mediatek/mtk_eth_soc.o
drivers/net/ethernet/mediatek/mtk_eth_soc.c:70:5: error: conflicting types for 'mtk_m32'
 u32 mtk_m32(struct mtk_eth *eth, u32 mask, u32 set, unsigned reg)
     ^~~~~~~
In file included from drivers/net/ethernet/mediatek/mtk_eth_soc.c:25:
drivers/net/ethernet/mediatek/mtk_eth_soc.h:964:6: note: previous declaration of 'mtk_m32' was here
 void mtk_m32(struct mtk_eth *eth, u32 clear, u32 set, unsigned reg);
      ^~~~~~~
```

which caused by 5.4.34 mainlining of mtk_m32 function.

Fixes: faf668be35 ("kernel: bump 5.4 to 5.4.34")
Signed-off-by: Yong-hyu, Ban <perillamint@quendi.moe>
2020-04-27 22:32:07 +02:00
INAGAKI Hiroshi
c998ae7f0e ramips: use lzma-loader for I-O DATA mt7621 devices
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.

This commit fixes the issue by using lzma-loader.

Note:
  These devices use Z-LOADER to read the kernel from NAND flash and boot
  it. Z-LOADER cannot load and start plain lzma-loader, so additional
  lzma-compression is needed.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
2020-04-27 12:22:02 +02:00
INAGAKI Hiroshi
a25bb8610f ramips: use lzma-loader for Japanese mt7621 devices
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.

This commit fixes the issue by using lzma-loader.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-27 12:22:02 +02:00
Szabolcs Hubai
ce19571004 ramips: mt7621: use lzma-loader for D-Link DIR-860L B1
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.

Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.

Factory image sizes (commit: 5f126c541a) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default): 4784188 bytes, LZMA ERROR 1
- with "-d19": 4915260, LZMA ERROR 1
- with "-d18": 4915260, diff to original: +128 KB
- with "-d17": 4980796, diff to original: +192 KB
- with this patch: 4849724, diff to original: +64 KB

To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.

The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!

[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:22:02 +02:00
David Bauer
654eec5a2d ath79: enable SGMII workaround for affected boards
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:22:02 +02:00
David Bauer
c760469918 ath79: ag71xx: unify version dependent code
Use IS_ERR_OR_NULL macro to use the same code on kernel 4.19 as well as
5.4.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:21:45 +02:00
David Bauer
5358d8b995 ath79: ag71xx: remove code for legacy kernels
ath79 does not support kernels prior to 4.19 anymore.
Remove legacy code for those kernels from the ag71xx driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:20:41 +02:00
David Bauer
3f5997fb28 ath79: remove unused TP-Link partition parser
This parser was added with the target, but no device seems to use it
currently, as all partitions are specified in the device-tree.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:20:41 +02:00
Adrian Schmutzler
3fdb08681b mvebu: tidy up support for GL.iNet GL-MV1000
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:

- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 00:25:12 +02:00
DENG Qingfang
ad697aabc3 bcm53xx: 5.4: enable NAND
NAND driver was dropped in the 5.4 bump, so enable it back

Fixes: 50c6938b95 ("bcm53xx: add v5.4 support")
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-26 21:45:41 +02:00
Li Zhang
050c24f05c mvebu: add support for GL.iNet GL-MV1000
This patch adds supports for GL-MV1000.

Specification:
	- SOC: Marvell Armada 88F3720 (1GHz)
	- Flash: 16MB (W25Q128FWSIG)
	- RAM: 1GB DDR4
	- Ethernet: 3x GE (1 WAN + 2 LAN)
	- EMMC: 8GB EMMC (KLM8G1GETF-B041)
	- MicroSD: 1x microSD slot
	- USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC)
	- Button: 1x reset button,1x slide switch
	- LED: 3x greed LED
	- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)

	Update firmware instructions
	============================
	In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web.

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[Copied dts file to files-5.4]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-04-26 21:45:41 +02:00
Matt Merhar
ee500186a5 kernel: backport fix for non-regular inodes on f2fs
Upstream commit dda9f4b9ca ("f2fs: fix to skip verifying block address
for non-regular inode").

On 4.14, attempting to perform operations on a non-regular inode
residing on an f2fs filesystem, such rm-ing a device node, would fail
and lead to a warning / call trace in dmesg. This fix was already
applied to other kernels upstream - including 4.19, from which the patch
was taken.

More info at https://bugzilla.kernel.org/show_bug.cgi?id=202495.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2020-04-26 21:45:41 +02:00
Sungbo Eo
1dedad2a00 ramips: remove unnecessary DEVICE_PACKAGES for Belkin F7C027
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:13:33 +02:00
Sungbo Eo
d16a486766 ramips: fix SUPPORTED_DEVICES for Mercury MAC1200R v2
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.

Fixes: c2334ad60d ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:10:24 +02:00
Sungbo Eo
01961f163d oxnas: move service file to correct place
This service file has been misplaced from the very beginning.

Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:05:15 +02:00
Petr Štetiar
97d86426e2 x86: fix unusable squashfs images by adding missing padding
It was reported, that after image generation rework
x86-64-generic-squashfs-rootfs.img image won't boot on XenServer x86_64
anymore:

 F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x84289960)
 F2FS-fs (xvda): Can't find valid F2FS filesystem in 1th superblock
 F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x4e8ee223)
 F2FS-fs (xvda): Can't find valid F2FS filesystem in 2th superblock
 List of all partitions:
 ca00            4207 xvda
  driver: vbd
 No filesystem could mount root, tried:
  ext3
  ext2
  ext4
  squashfs
  iso9660
  f2fs

 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(202,0)

So lets fix this by adding back padding which was introduced in commit
a17d9482f5 ("x86: image: fix small disk space in squashfs overlay").

Ref: FS#3036
Fixes: 258f070d1a ("x86: fix missing squashfs and ext4 rootfs images")
Fixes: cb007a7bf6 ("x86: switch image generation to new code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-26 12:53:27 +02:00
René van Dorst
4c70bb4f90
ramips: enable SFP port for Ubiquiti ER-X-SFP
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch.
This phy act as a RGMII-to-SerDes converter.

Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus.
SFP cage also has module detect pin which is connected to I2C gpio expander.

With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.

NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding!
This means that some SGMII modules can work and only at forced 1GBit/full-duplex!

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:48:45 +02:00
René van Dorst
ec2f7a47d3 kernel: add module to support SFP cages
Enables kernel SFP case support.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
DENG Qingfang
6d924706a6 ramips: phy: at803x: support RGMII-to-SerDes and SFP support
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
DENG Qingfang
63696bd0fb kernel: backport support for clause 37 1000Base-X auto-negotiation
This patch is needed for clause 37 1000Base-X encoding used in many SFP modules.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
Petr Štetiar
ef5d37ba5e kernel: bump 5.4 to 5.4.35
Refreshed one patch.

Run tested: qemu-x86-64
Build tested: x86/64, imx6, sunxi/a53, rockchip/armv8

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-25 13:22:28 +02:00
Petr Štetiar
4a3e0f736f imx6: add back perf monitor related config symbol
Commit 0543eb1110 ("imx6: 5.4: add missing kernel perf monitor
symbol") has added missing kernel config symbol FSL_IMX8_DDR_PMU which
is exposed only when building perf, so add it back.

Fixes: 8d9b36270b ("imx6: refresh kernel config")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-25 13:22:28 +02:00
David Bauer
9fac9168c6 ipq40xx: fix alphabetical order in 02_network
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:41 +02:00
David Bauer
1f45ed6c99 ath79: fix QCA953x DDR and GPIO compatible bindings
The memory as well as GPIO controller had the wrong SoC name used for
their compatible binding.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:18 +02:00
David Bauer
fceef288cf ath79: correct QCA9550 machine compatible binding
Some boards using a QCA9556 or QCA9558 had their machine compatible
binding incorrectly set to qca,qca9557.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:00 +02:00
David Bauer
c0a80b7125 ath79: rename qca9557.dtsi to qca955x.dtsi
There are at least 3 different chips in the Scorpion series of SoCs.
Rename the common DTSI to better reflect it's purpose for the whole
series.

Also rename the compatible bindings from qca,ar9557 and qca,qca9557
to qca,qca9550.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:02:29 +02:00
Adrian Schmutzler
d3c9630811 ath79: move tplinkpart.c parser to patches
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Like for myloader.c in the previous patch,
this patch moves tplinkpart.c to the kernel patches, so the
code and the kernel includes are at the same location and
the path can be adjusted per kernel.

While at it, remove some outdated kernel version switches from
the C code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-24 17:50:59 +02:00
Adrian Schmutzler
5f92349841 kernel: fix include of myloader.o since kernel 5.4
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Based on this, the selection of myloader.o in OpenWrt
was also moved to that subdirectory, while the Kconfig and our local
myloader.c file remained in /drivers/mtd.

This resulted in linking errors like the following (on ath25@5.4):

make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ...
   needed by 'drivers/mtd/parsers/built-in.a'.  Stop.
make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2
make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2

Since myloader.c is not too big, this patch moves it to the kernel patches,
allowing to adjust the path for kernel 5.4 and keeping Makefiles and
file paths better in sync.

Other patches have been refreshed accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-24 17:50:12 +02:00
Adrian Schmutzler
58bec0d172 ramips: remove config-4.14 for mt7621/mt76x8
mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their
DTS(I) files are incompatible to kernel 4.14.

Remove the corresponding kernel config files to signal that more
boldly and to prevent accidentally patching the wrong kernel when
pulling in older config patches.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:39:48 +02:00
Adrian Schmutzler
f6573ec24e octeon: use kernel version 5.4 for testing
Tested on EdgeRouter Lite (by Daniel Engberg)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:54 +02:00
Daniel Engberg
2095a4e276 octeon: update config for kernel 5.4
Update config with make kernel_oldconfig.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, redo kernel_oldconfig, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:32 +02:00
Daniel Engberg
655c14e88c octeon: refresh patches for kernel 5.4
Refresh patches to make them apply to kernel 5.4.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, refresh on newer kernel, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:26 +02:00
Daniel Engberg
91594cb137 octeon: copy files to kernel 5.4
Copy config and patches to kernel 5.4.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, fix patches-5.4 dirname, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:19 +02:00
Felix Fietkau
df27e949fb mediatek: disable the unused pcie port for elecom wrc-2533gent
Fixes MSI support for the primary device

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-04-22 10:50:15 +02:00
Petr Štetiar
faf668be35 kernel: bump 5.4 to 5.4.34
Refreshed patches.

Run tested: qemu-x86-64, apalis, a64-olinuxino
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-21 22:16:33 +02:00
Koen Vandeputte
8d9b36270b imx6: refresh kernel config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-21 14:46:52 +02:00
Alexander Couzens
36f628910b lantiq/fritz 7312: set maximum speed to 100 mbit
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2020-04-21 00:01:49 +02:00
Daniel Golle
be6543c539 x86: really remove packages already enabled in kconfig
This commit really removes packages in geode profiles already enabled
in kernel config.

Fixes: 9c23ecee57 ("x86: move packages selection to profiles")
Reported-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-20 19:24:18 +01:00
Tomasz Maciej Nowak
9c23ecee57 x86: move packages selection to profiles
This can be rather confusing for contributors, since there are three
layers in which they can be added. As for now there are none profiles
other than generic (exception: geos) let's move them to these profiles.
Being here this commit also removes packages in geode profiles already
enabled in kernel config.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tomasz Maciej Nowak
eca6946447 x86: select kmod-button-hotplug by default
This package is useful by all subtargets, therefore move it to default
packages selection.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tomasz Maciej Nowak
fd94d03ae6 x86: fix kmod-forcedeth package selection
There's no such package as forcedeth, threfore the driver is never
selected. Fix it by properly specifying package name.

Fixes: 35f208d ("x86: add nforce eth to default packages")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tomasz Maciej Nowak
282e7862b7 x86: image: drop dead code
These are remnants of old image generation code, which now serve no
purpose.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tobias Mädel
6a05a85dcb rockchip: add support for Pine64 RockPro64
This adds the new rockchip target and support for RockPro64 RK3399

Flash:    16 MiB SPI NOR
RAM:      2 GiB/4 GiB LPDDR4
SoC:      RK3399
USB:      2x USB 2.0, 1x USB 3.0, 1x USB-C
Ethernet: 1x GbE
PCIe:     PCIe 2.0, 4 lanes
Storage:  eMMC or SD card
Optional SDIO wifi/bt module

The Pine64 RockPro64 is a single-board-computer with a 4x PCIe connector,
6 ARM64 cores (4 little, 2 big), plenty of RAM and storage.

By default the single Gigabit-Ethernet port is configured as the
LAN port.

Installation of the firware is possible by dd'ing the image
to an SD card or the eMMC flash.

Serial: 3v3 1500000 8n1

U-boot is build from the mainline tree and
integrated into the images. Required ATF to build u-boot
is downloaded from a CI build bot.

Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-20 16:37:56 +02:00
Pawel Dembicki
08f5cac6fb ramips: mt7621: add NETGEAR R7200 as DEVICE_ALT1
Netgear R7200 is another clone of Netgear R6700v2, introduced in:
6e80df5 ("ramips: add support for NETGEAR R6700v2/AC2400")

Reported-by: Joel Pinsker, github user @joelp64
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-20 11:13:39 +01:00
David Bauer
8d9c1087e4 ath79: add support for AVM FRITZ!WLAN Repeater 450E
SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.

Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-19 16:45:40 +02:00
Sungbo Eo
45e2b7763f ramips: replace pinctrl property names for ipTIME A1004ns
The pinctrl driver had been replaced with the upstream one in b756ea2a90
("ramips: replace pinctrl property names"), but the initial A1004ns support
patch did not reflect the changes. This commit updates its pinctrl property
names.

Fixes: 9169482f64 ("ramips: add support for ipTIME A1004ns")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-19 13:47:23 +08:00
Álvaro Fernández Rojas
d27e2c67ed bcm63xx: switch to 5.4 kernel
Seems stable after 6 days of testing on some of my devices.
Let's switch to 5.4 in order to get more feedback.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-18 20:58:38 +02:00
Chuanhong Guo
19d9db5a96 ramips: mt7621: use lzma-loader for newifi d1/d2/thunder timecloud
These devices failed to properly extract kernel. enable lzma loader
for them.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 14:19:38 +08:00
Chuanhong Guo
1e5d014ba2 ramips: don't reuse KERNEL_DTB for lzma-loader
mt7621 overrides KERNEL_DTB to limit dictionary size, which isn't needed
for our lzma loader.
This saves 15KB on mt7621 devices using uimage-lzma-loader.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 13:40:31 +08:00
Chuanhong Guo
51c6b14092 ramips: mt7621: backport more pcie driver fixes
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 13:06:48 +08:00
Sungbo Eo
13a185bf8a ramips: increase spi-max-frequency for ipTIME mt7620 devices
This commit increases the hardware SPI frequency from 24.2MHz to 48.3MHz.

[    5.314163] m25p80 spi0.0: speed: 24166666/40000000, rate: 8, prescal: 2, loops: 226
[    5.076323] m25p80 spi0.0: speed: 48333333/50000000, rate: 4, prescal: 1, loops: 162

`time cat /dev/mtd2 >/dev/null` is reduced from 5.64s to 4.36s on A104ns,
and from 11.39s to 8.81s on A1004ns.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-18 12:35:54 +08:00
Sungbo Eo
9169482f64 ramips: add support for ipTIME A1004ns
ipTIME A1004ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- USB: 1x 2.0
- UART:
  - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-18 12:35:54 +08:00
René van Dorst
d682dcc939 ramips: mt7621: Ubiquiti ER-X-SFP: fix gpio numbers for POE enable gpios
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-18 11:59:41 +08:00
René van Dorst
2fac1322f7 ramips: mt7621: Ubiquiti ER-X: fix gpio number for POE enable gpio
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-18 11:59:41 +08:00
DENG Qingfang
d74fb0088c ramips: use all reserved space for HiWiFi HC5962
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-18 11:52:12 +08:00
DENG Qingfang
7dc82528a2 ramips: increase HiWiFi HC5962 kernel partition to 4M
Increase kernel partition because 2M is insufficient for 5.4
Because the partition changes, previous version of OpenWrt cannot upgrade
to this version, and requires a new installation

Recovery to stock instruction:
1. Download stock firmware at
   http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin
2. Power off the router
3. Press and hold the reset button for 4~6 sec while power it back on
4. Connect a PC to router's LAN
5. Visit http://192.168.2.1 and upload the firmware

Then repeat the instruction in edae3479e6 to install OpenWrt

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-18 11:50:57 +08:00
Mantas Pucka
4745969ad7 generic: spi-nor: fix 4-byte opcode support for w25q256
There are 2 different chips (w25q256fv and w25q256jv) that share
the same JEDEC ID. Only w25q256jv fully supports 4-byte opcodes.
Use SFDP header version to differentiate between them.

Fixes broken reboot on 8devices Habanero since f0f35fdac

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2020-04-18 11:37:06 +08:00
Petr Štetiar
23916bca61 kernel: bump 5.4 to 5.4.33
Refreshed patches, removed upstreamed patches:

 oxnas: 001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch
 oxnas: 002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch

Run tested: qemu-x86-64, apalis
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-17 15:18:12 +02:00
David Bauer
edf812e25c ath79: remove stray pipe
Fixes: 8918c038f3 ("ath79: add support for AVM FRITZ!WLAN Repeater 1750E")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 14:15:09 +02:00
David Bauer
8918c038f3 ath79: add support for AVM FRITZ!WLAN Repeater 1750E
This commit adds support for the AVM Fritz!WLAN Repeater 1750E

SOC:	Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
WLAN2:  QCA9880 5 GHz 802.11 n/ac 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (correct MAC)
 - 5 GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 13:27:40 +02:00
David Bauer
d883eaacd4 ath79: add QCA9550 reset sequence
The QCA9550 family of SoCs have a slightly different reset
sequence compared to older chips.

Normally the bootloader performs this sequence, however
some bootloader implementation expect the operating system
to clear the reset. Also get the PCIe resets from OF to
support the second RC of the QCA9558.

This is required for the AVM FRITZ!WLAN Repeater 1750E to work,
as EVA leaves the PCIe bus in reset.

Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 13:23:06 +02:00
Koen Vandeputte
75ef28be59 kernel: add support for GD25D05 SPI NOR (5.4)
This chip is used on newer RB912UAG-5HPnD r2 and 922UAGS-5HPacD boards:

Before:

[    0.824562] spi-nor spi0.0: unrecognized JEDEC id bytes: c8 40 10 c8 40 10
[    0.831607] spi-nor: probe of spi0.0 failed with error -2

After:

[    0.825347] spi-nor spi0.0: gd25d05 (64 Kbytes)
[    0.830291] 1 routerbootpart partitions found on MTD device spi0.0
[    0.836577] Creating 1 MTD partitions on "spi0.0":
[    0.841448] 0x000000000000-0x000000010000 : "partitions"
[    0.848418] 4 routerbootpart partitions found on MTD device partitions
[    0.855092] Creating 4 MTD partitions on "partitions":
[    0.860318] 0x000000000000-0x00000000c000 : "routerboot"
[    0.866548] 0x00000000c000-0x00000000d000 : "hard_config"
[    0.872832] 0x00000000d000-0x00000000e000 : "bios"
[    0.878580] 0x00000000e000-0x00000000f000 : "soft_config"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 14:36:35 +02:00
Roger Pueyo Centelles
c0430b8da4 ath79: reduce spi-max-frequency for Mikrotik wAP G-5HacT2HnD
The previous spi-max-frequency value did not work with all the CPU speed
settings (configurable with rbcfg or from the stock firmware); the new
one does for the three of them.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-04-16 13:44:18 +02:00
Koen Vandeputte
20efd5614a ath79: MikroTik: fix missing nand on kernel 5.4
Following symbol got renamed upstream:
CONFIG_MTD_NAND --> CONFIG_MTD_RAW_NAND

Also add this renamed symbol so NAND also works on kernel 5.4.

After:
[    0.628372] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    0.634862] nand: Samsung NAND 128MiB 3,3V 8-bit
[    0.639554] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.647263] Scanning device for bad blocks
[    0.656228] random: fast init done
[    0.789652] 3 fixed-partitions partitions found on MTD device ar934x-nand
[    0.796550] Creating 3 MTD partitions on "ar934x-nand":
[    0.801874] 0x000000000000-0x000000040000 : "booter"
[    0.807715] 0x000000040000-0x000000400000 : "kernel"
[    0.813551] 0x000000400000-0x000008000000 : "ubi"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00
Koen Vandeputte
3c3825436e kernel: bump 4.19 to 4.19.115
Refreshed all patches.

Remove upstreamed:
- 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
- 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch

Fixes:
- CVE-2020-8647
- CVE-2020-8648 (potentially)
- CVE-2020-8649

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00
Koen Vandeputte
e31d158c4d kernel: bump 4.14 to 4.14.176
Refreshed all patches.

Remove upstreamed:
- 0001-net-thunderx-workaround-BGX-TX-Underflow-issue.patch
- 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
- 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch

Fixes:
- CVE-2020-8648 (potentially)
- CVE-2020-8647
- CVE-2020-8649

Compile-tested on: cns3xxx, octeontx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00
Hannu Nyman
a7423fef32 ath79: improve status LED definitions for GL-AR750
Improve the status LED functionality in GL-AR750
by adding the definitions for different statuses
(boot, failsafe, running, flashing).

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-04-16 00:02:03 +02:00
Adrian Schmutzler
508462a399 ath79: add SUPPORTED_DEVICES for TP-Link TL-WA901ND v2
This adds the board name from ar71xx to support upgrade without
-F for the TP-Link TL-WA901ND v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-15 12:47:43 +02:00
Chuanhong Guo
ad19751edc ramips: mt7621: enable lzma-loader for some devices
ubnt er-x/xiaomi/netgear sercomm devices are known to have troble
extracting a big kernel from flash and has support for uncompressed
uimage
This commit uses uncompressed uimage with lzma-loader for these devices
to fix boot issue.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-15 10:14:19 +08:00
Paul Spooren
f814121600 x86: append metadata to combined images
Now that the x86 target uses the new image generation code we can also
attach metadata to the created images.

As currently the `SUPPORTED_DEVICES` list is empty, no JSON metadata is
attached, however the signing happens in the same step.

This results in signature verification for x86 images.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-04-14 23:38:08 +01:00
Petr Štetiar
0bea89a1d0 kernel: bump 5.4 to 5.4.32
Refreshed patches, removed upstreamed patches:

 generic: 746-stable-net-dsa-mt7530-fix-null-pointer-dereferencing-in-por.patch

Run tested: qemu-x86-64, apalis
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-14 21:58:16 +02:00
Ansuel Smith
9abf01246e ipq806x: add patch to fix broken buttons
From kernel 4.20 msm-gpio driver is broken and cause the
malfunction of the buttons on every ipq806x target.
Add a patch to fix this.

Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2020-04-14 21:58:16 +02:00
Adrian Schmutzler
d0cb6e995b ath79: further fixes for ZyXEL NBG6716
This applies further fixes to the DTS of ZyXEL NBG6716 based on
what is found in ar71xx (mach-nbg6716.c):

- use WiFi label names as in ar71xx
- fix WPS gpio number
- fix GPIO_ACTIVE_HIGH and mode for WiFi switch
- add codes for USB eject buttons
- fix node name for "internet" LED

This device has separate LEDs for WAN and "Internet". As the WAN-LED
(and the four LAN-LEDs) are driven independent of the setup in
DT/01_leds, the "internet" LED is left unassigned (in contrast to
ar71xx, where it was set up effectively as a second WAN LED)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-14 12:03:57 +02:00
Chuanhong Guo
75f19deb3a ramips: define image recipe for uncompressed uimage with loader
Some devices have bootloaders with broken lzma code resulting in failed
decompression or corrupted kernel code.
This image recipe allows to sacrifice 5KB for OpenWrt LZMA loader and
take over the task of decompress kernel.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 12:01:50 +08:00
Chuanhong Guo
d9e9a0e6b1 ramips: define lzma loader platform in target
Loader platform is a per-soc variable instead of a per-device one.
Determine corresponding loader platform at the beginning of image
Makefile.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 11:17:47 +08:00
Chuanhong Guo
111029bea7 ramips: add missing DEVICE_VARS for lzma-loader
LOADER_TYPE is a per-device variable which should be included in
DEVICE_VARS.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 11:14:15 +08:00
Luiz Angelo Daros de Luca
1b2c4af039 ath79: enable m25p,fast-read for tplink,tl-wr1043-v1
Enables spi-mem interface for 3x faster flash read.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2020-04-14 10:47:23 +08:00
Luiz Angelo Daros de Luca
e430dfdd69 ath79: enable m25p,fast-read for tplink,tl-wr2543-v1
Enables spi-mem interface usage. It speeds up flash read
in about 3x while it also workaround a possible hardware
bug when normal spi read is used.

Fixes: FS#2742

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2020-04-14 10:47:23 +08:00
Luiz Angelo Daros de Luca
b3f9842330 ath79: add read support using spi-mem
Reimplements read optimization on top of spi-mem. Similar to
what 461-spi-ath79-add-fast-flash-read.patch used to do with
the dropped flash read interface.

It accelerate only fast-read op reading flash directly from
memory mapped region. 'm25p,fast-read' must be set in order
to use the new spi-mem.

It improved read speed up to 3x on old devices (tplink,tl-wr2543-v1)
while no speed improvement was noticed on newer devices like
(tplink,archer-c7-v2).

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2020-04-14 10:47:23 +08:00
Alberto Bursi
35f208da3c x86: add nforce eth to default packages
forcedeth is necessary to use the integrated
ethernet controller of Nvidia nForce chipset.

There are PC motherboards with this chipset
from 2001 that run 32bit Athlon XP CPUs and
more modern ones up to 2009 that can run Intel
and AMD 64bit processors, so add this to
all non-geode x86 targets.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-04-13 22:41:37 +02:00
Tomasz Maciej Nowak
779a1c84ea mvebu: drop armada-37xx PCI aardvark patches
These patches were necessarry for Atheros and some Intel WiFi cards.
After short testing, the current upstream driver state is enough for
these WiFi cards to work. If there are still some issues with other
devices, the patches could be easily restored.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-13 22:41:37 +02:00
DENG Qingfang
f72a13b537 mvebu: refresh config
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
DENG Qingfang
d13fe4127c mvebu: refresh patches
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
DENG Qingfang
ae183c128f mvebu: set kernel testing version to 5.4
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
DENG Qingfang
70193703a9 mvebu: copy files and patches to 5.4
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
Daniel González Cabanelas
85ef69b202 mvebu: add support for Buffalo LinkStation LS421DE
Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370

Hardware:
   SoC:         Marvell Armada 88F6707-A1
   CPU:         Cortex-A9 1200 MHz, 1 core
   Flash:       SPI-NOR 1 MiB, NAND 512 MiB
   RAM:         DDR3 512 MiB
   Ethernet:    1x 10/100/1000 Mbps
   USB:         1x 2.0, 1x 3.0
   SATA:        2x 3.0 Gbps
   LEDs/Input : 5x / 2x (1x button, 1x slide-switch)
   RTC:         Ricoh RS5C372A, I2C, no battery

Flash instruction (UART+TFTP):
  1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13)
  2. Remove any hard drive from inside the bays.
  3. Boot the Openwrt initramfs image using the U-Boot serial console:
         tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin
         bootm 0x1200000
  4. Flash the sysupgrade image using the Openwrt console:
         sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
  5. Wait until it finish, the device will reboot with Openwrt installed
     on the NAND flash.

Note:
  - Device shuting down doesn't work, even if the power slide switch is
    used. We must first, via MDIO, set the unused LED2 at the ethernet
    phy0 to off state. Reboot works ok.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-13 22:41:14 +02:00
Aleksander Jan Bajkowski
b43023b7ba kernel: remove non-existant symbols
These symbols exist only in older kernels and can be removed.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-04-13 22:40:19 +02:00
Adrian Schmutzler
97af28d23e ath79: fix USB port LED assignment for ZyXEL NBG6716
The USB LED assignment to internal ports was swapped.

Fix it.

We also explicitly checked that the LED label numbers match those
on the device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-13 19:22:16 +02:00
Guillaume Lefebvre
f5a9181d6e ath79: fix wmac initialization for Zyxel NBG6716
2.4 GHz Wifi on ath79 is set up in 10-ath9k-eeprom, but in ar71xx
it was done with ath79_register_wmac.

Thus, the following errors are observed on the device:
ath: phy1: Unable to initialize hardware; initialization status: -5
ath9k 18100000.wmac: failed to initialize device
ath9k: probe of 18100000.wmac failed with error -5

This patch changes the ath79 support to properly use wmac as well.
This will also require fixing the MAC address in a different way.

Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
[several adjustments to 10-fix-wifi-mac, use correct MAC address,
rewrite commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-13 19:21:56 +02:00
Chuanhong Guo
77b99ea3c6 ramips: fix whitespace in 990_NET-no-auto-carrier-support.patch
Fixes: 6fcba5eec3 ("ramips: port 0034-NET-multi-phy-support.patch to 5.4")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-13 11:49:16 +08:00
Chuanhong Guo
4d06229242 ramips: ralink-eth: fix leftover dma dev argument
Fixes: 05dee5833a ("ramips: ralink-eth: fix device struct passed to dma functions")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-13 11:32:50 +08:00
Jonas Gorski
4e535d81ee bcm63xx: disable all devices with <= 4MiB flash and <= 32 MiB RAM
Device with 4 MiB flash and 32 MiB RAM won't be able to run OpenWrt in
a sufficient manner without tweaks, so don't build images for them by
default.

This includes all BCM6338, BCM6345 and BCM6348 "generic" devices,
as there are no supported devices of these with more than that.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2020-04-12 20:45:21 +02:00
Chuanhong Guo
b756ea2a90 ramips: replace pinctrl property names
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:29:17 +08:00
Chuanhong Guo
8f6334eb94 ramips: explicitly disable built-in switch when needed
previously we rely on the failsafe setup in preinit scripts to disable
built-in switch implicitly for single-port devices. This doesn't work
anymore due to preinit script removal.
this patch explicitly disable built-in switch for needed devices.

Fixes: a8d62a4eb1 ("ramips: remove set_preinit_iface script")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:29:17 +08:00
Chuanhong Guo
605a7ffff2 ramips: add 5.4 as testing kernel
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
abadee5d60 ramips: mt76x8: switch to kernel 5.4
4.14 doesn't work anymore due to gpio dt binding changes. Switch mt76x8
to 5.4 directly.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
d7d46da938 ramips: disable images for 4M devices
default initramfs for 5.4 kernel is larger than 4M, causing build error
for oversized initramfs image.
disable these images because we have no mechanism for ignoring initramfs
errors and the squashfs image will be larger than initramfs anyway.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
e29e2a9484 ramips: ralink-eth: add support for 5.4 kernel
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
0b68d081eb ramips: mt7628: update dts for upstream gpio-mt7621 driver
upstream driver merged 3 separated gpio banks into one gpio node.
and gpioX Y in our local driver should be replaced with gpio X*32+Y.

This patch is created using the following sed command:
sed -i -r 's/(.*)gpio([0-9]) ([0-9]+)(.*)/echo "\1gpio $((\2*32+\3))\4"/ge'

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
e320435a6a ramips: refresh kernel config for 5.4
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00