Siflower SF19A2890 is an SoC with:
Dual-core MIPS InterAptiv at 800MHz
DDR3 controller
One Gigabit Ethernet MAC with RGMII and IPv4 HNAT engine
Built-in 2x2 11N + 2x2 11AC WiFi radio
USB 2.0 OTG
I2C/SPI/GPIO and various other peripherals
This PR adds support for SF19A2890 EVB with ethernet support.
EVB spec:
Memory: DDR3 128M
Ethernet: RTL8367RB 5-port gigabit switch
Flash: 16M NOR
Others: MicroUSB OTG, LED x 1, Reset button x1
The built image can be flashed using u-boot recovery.
This target is marked as source-only until support for a commercial
router board comes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].
[0] https://forum.openwrt.org/t/206640
Signed-off-by: Andreas Böhler <dev@aboehler.at>
RELR is a relocation packing format for relative relocations.
Linux has supported using it for ARM64 since 5.4, and more recently
for LoongArch as well.
It requires compatible tooling as well, so only with binutils 2.43
TOOLS_SUPPORT_RELR is set and thus RELR available.
RELR should always decrease the binary size and while testing this
the default build for Dynalink WRX-36 (qualcommax/ipq807x) reduced
the compressed kernel size by 38k and uncompressed one by 640k.
So, lets enable it in the default config.
Link: https://github.com/openwrt/openwrt/pull/16403
Signed-off-by: Robert Marko <robimarko@gmail.com>
Merging of the realtek 6.6 series forgot to include some final fixes
for the new MDIO driver. What was changed in last second?
1. The MDIO driver used wrong constants to make use of the raw
page (for direct register access). Provide a rawpage variable in
the bus private structure, populate it during initialization and
make use of it at the proper places
2. We always used the variable portaddr for the bus index. Usually
our driver uses either addr or port for the same meaning. Remove the
duplication and reuse the normal addr variable.
3. Drop functions rtmdio_write_page() and rtmdio_read_page(). These
only call the PHY driver read/write page functions. We know that
these will only access page 0x1f. As we have only Realtek PHYs
and our driver only reacts to this special page, just hardcode it.
Benefit is that we can use these functions for PHY detection when
read/write page functions are not yet assigned.
4. Add two new helper functions phy_port_read_paged() and
phy_port_write_paged(). These allow to access arbitrary ports on
the MDIO bus when the packages are not initialized. These will be
needed for proper RTL8218B and RTL8214FC detection in forthcoming
patches.
5. The port tracking wrongly used index 0 to mark "normal" access.
This does not allow to make a "special" access to port 0. Use
index -1 to mark "normal" access.
Provide the fix for 5.15 and 6.6 to allow for easy version
comparison.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
With commit a22d359fa5 VLAN handling was fixed for kernel 6.6.
This restored network connectivity of the devices. For easy testing
backport the fix for 5.15 too.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
On the XGS1210-12 the RTL8218D is attached via XGMII. Add this to the
supported list in the DSA driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
We switched to 6.6, so lets remove 6.1 support now.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unset CONFIG_CRYPTO_MANAGER_DISABLE_TESTS and
CONFIG_CRYPTO_MANAGER_EXTRA_TESTS manually to fix these linker errors:
crypto/crypto_engine.o: in function `crypto_engine_register_akcipher': undefined reference to `crypto_register_akcipher'
crypto/crypto_engine.o: in function `crypto_engine_unregister_akcipher': undefined reference to `crypto_unregister_akcipher'
crypto/crypto_engine.o: in function `crypto_engine_register_kpp': undefined reference to `crypto_register_kpp'
crypto/crypto_engine.o: in function `crypto_engine_unregister_kpp': undefined reference to `crypto_unregister_kpp'
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
.dts files were moved to the 'ti/omap' sub-directory.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bring it in line with all the other targets.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DGS-1210-28MP has a LM63 fan controller connected via i2c of the
RTL8231. The clock line is always low if the property
i2c-gpio,scl-open-drain is not set; with this property, the GPIO pin is
force-drive and the clock works as expected.
The LM63 is not configured by U-Boot, thus only manual fan control is
possible by settings pwm1_enable to "1" and writing the desired values to
pwm1.
The OEM firmware drives the fan from user mode and sets it up like this:
// PWM LUT/value r/w, PWM Clock = 1.4kHz
0x4a 0x28
// Tachometer spinup disabled, spin-up cycles bypassed
0x4b 0x00
// PWM Frequency = default
0x4d 0x17
// PWM Value (28)
0x4c 0x1c
// If > 0 C, use
0x50 0x00
// PWM = 28
0x51 0x1c
// If > 51 C, use
0x52 0x33
// PWM = 44
0x53 0x2e
// Set hysteresis to 100 = default
0x4f 0x03
// Turn on automatic mode and w/p the LUT values
0x4a 0x08
A thread in the OEM firmware polls the ALERT status register for fan
failures.
Unfortunately, the lm63 kernel driver does not perform any initialization
of the chip and it does not support changing some config registers (like
PWM frequency or LUT). Hence, we are stuck with the defaults and need to do
fan control in software.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/15616
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The DGS-1210-28 series was lacking full SFP support due to missing GPIOs.
Fortunately, the existing GPIO definitions of DGS-1210-52 match, this adds
the required i2c-gpio nodes to the DTS and allows hotplug SFP support.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/15616
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The one for the mx60 was wrong. The LAN MAC is offset by one.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14037
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qca8k driver is upstream, unlike swconfig. This applies to the mx60
and wndr4700 only. Fixed up LED definitions as well.
RTL83xx DSA for WNDAP62300/660 is not working.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14037
Signed-off-by: Robert Marko <robimarko@gmail.com>
The CPU port of realtek switches needs some proper PVID set to handle
untagged packets. Because the ethernet driver does no special VLAN
handling (see CPU tag RVID/RVID_SEL) as of now we can only steer
untagged packets by setting PVID for the CPU port. VLAN handling has
never been perfect but 3 events made things worse.
- Commit a376508216 ("rtl83xx: dsa: Do nothing when vid 0")
- Commit e691e2b302 ("rtl83xx: dsa: reset PVID to 1 instead of 0")
- Upgrade to kernel 6.6
Reasons are:
- Rejecting VID 0 disabled Linux initialization routines
- Initialization for PVID forgot to set priv->ports[port].pvid
- Kernel 6.6 does no longer clarify CPU port as untagged
To fix this prepare the VID 0 setup inside the driver. Join all ports
to VID 0 and let no one from outsinde interfere with this setup.
Especially ignore PVID settings for the CPU port for all further
VLAN commands.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Since kernel commit c5714f68a76bcad3d ("net: phylink: explicitly invalidate
link_state members in mac_config") it should be clear that link data can
only be used in mac_link_up(). Refactor that for the RTL83xx targets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Some devices (e.g. HP JG924A) hand over other than expected kernel boot
arguments. Looking at these one can see:
fw_init_cmdline: fw_arg0=00020000
fw_init_cmdline: fw_arg1=00060000
fw_init_cmdline: fw_arg2=fffdffff
fw_init_cmdline: fw_arg3=0000416c
Especially fw_arg2 should be the pointer to the environment and it looks
very suspicous. It is not aligned and the address is outside KSEG0 and
KSEG1. Booting the device will result in a hang. Do better at verifying
the address.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Suggested-by: Bjørn Mork <bjorn@mork.no>
The supported_interfaces bitmap cannot be empty since mainline kernel
commit de5c9bf40c45 ("net: phylink: require supported_interfaces to
be filled"). Fix the dsa and ethernet driver accordingly.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The DSA framework has changed a bit since 6.1, lets adapt to match.
Currently there is no one-patch-fits-all solution to directly fix
all errors up to 6.6. So cover the final differences with this
second patch.
Most notable upstream changes are:
- a88dd7538461 ("net: dsa: remove legacy_pre_march2020 detection")
- 53d04b981110 ("net: dsa: remove phylink_validate() method")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[Minor checkpatch.pl cleanups]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The DSA framework has changed a bit since 5.15, lets adapt to match.
Currently there is no one-patch-fits-all solution to directly fix
all errors up to 6.6. So at least take all the already known changes
that cover differences between 5.15 and 6.1
Most notable upstream changes are:
- d3eed0e57d5d ("net: dsa: keep the bridge_dev and bridge_num as part
of the same structure")
Update of port_bridge_{join,leave}: use same helper as upstream
- c26933639b54 ("net: dsa: request drivers to perform FDB isolation")
Update of port_fdb_{add,del}, port_mdb_{add,del}
- dedd6a009f41 ("net: dsa: create a dsa_lag structure")
Update of port_lag_{join,leave}
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[align updates with upstream, add references to upstream commits]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Only take over the new patch locations. All errors
that wil arise from compiling with the phy driver will be covered by
follow up patches.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Only adapt the failing hooks and take over the
new patch locations. All errors that wil arise from compiling with
the dsa driver will be covered by follow up patches.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
A lot of stuff has been converted to the phylink_pcs_ops structure.
Adapt the ethernet driver to make use of it.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
We no longer are required to pass the weight to netif_napi_add.
See commit b48b89f9c189 ("net: drop the weight argument from netif_napi_add").
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
This is not a surprise. Before upgrade to 6.6 we refactored the mdio part of
the ethernet driver and knew that changes will come. Drop all unnecessary
stuff from the old world and adapt to the new kernel.
- remove legacy functions
- directly link new functions
- adapt to new shared base address
- remove references to old MDIO bus capabilities
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Only take over the new patch locations. All errors
that will arise from compiling with the ethernet driver will be covered
by follow up patches.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
With the new kernel the MDIO bus gets created after the smbus
read/write functions are used. Make use of native functions.
Relocate bus initialization into a separate function to make
patch easier to read.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Take over the new patch locations and add references to the link mode into
phylink_sfp_interface_preference[] and phylink_get_capabilities().
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. As the order of the 7xx patch files seems very
strange reorder all of them according to the realtek 6.6 kernel upgrade
effort.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Only take over the new patch locations.
With this patch all platform specific changes for kernel 6.6 are in place.
Realtek devices are bootable from serial console. VPE is fully functional
on devices that support it. The switch functions (ethernet and DSA) are
not enabled yet.
Boot tested on RTL8380 (Linksys LGS310C) and RTL8393 (Zyxel GS1920-24).
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
VPE in mainline kernel has changed a lot. This patch wraps up the 5.15
patch files and rebases them in one single patch on top of kernel 6.6.
Former patches are
315-irqchip-irq-realtek-rtl-add-VPE-support.patch
319-irqchip-irq-realtek-rtl-fix-VPE-affinity.patch
Submitted-by: Birger Koblitz <git@birger-koblitz.de>
Submitted-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Copy the patch files to 6.6. Both target drivers/irqchip/irq-realtek-rtl.c
and are additions and fixes for IRQ VPE handling.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Copy the patch file to 6.6. No further processing required as
it applies cleanly to the new kernel
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
No content changes. Due to kernel changes the patch hooks totally failed
and had to be fixed manually.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The CONFIG_CLOCKSOURCE_WATCHDOG_MAX_SKEW_US is missing. Avoid
complaints and add it with its default 125.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Copy files and config from 5.15 kernel version. Because of the big version jump
leave out the patches for now so we can treat them individually later on.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
With commit b53202a8c3 ("realtek: switch to use generic MDIO accessor functions")
the phy access logic was enhanced. A quite big kernel patch was introduced that
allowed to make use of hardware-assisted page access like we have in the realtek
target. Basically it works the following way
- The enhanced bus intercepts page write accesses
- Currently selected pages are stored in internal vars.
- Finally only all-in-one-consistent bus/register accesses are issued
- It intercepted page changes and ensured that only a complete bus call
For the details see https://github.com/openwrt/openwrt/pull/16172
Switching over to newer kernels this patch is really hard to maintain. Its heavy
modifcations exist only in the realtek target. So it does not matter if we keep
it as an kernel modification or directly include it in our driver. To make it the
future brighter we drop this patch and take over its logic. Thus the kernel will
stay totally modification-free. What do we do?
1. Up to now the bus->priv structure directly pointed to ethernet->priv. Create an
explicit private structure rtl838x_bus_priv that not only holds the ethernet->priv
pointer but also space for some bus status tracking vars as well.
2. Wherever we use a reference to ethernet->priv directly replace that by an
additional indirection over the new rtl838x_bus_priv structure.
3. Up to now the phy flag PHY_HAS_REALTEK_PAGES identified that we can use the
alternative paged access from the patch. As this will be no longer available
remove it and provide read_page/write_page functions for each possible PHY.
These functions will be pretty standard as for other Realtek PHYs.
4. The existing mdio bus read/write function rely on the classic MII_ADDR_C45
flag - one interface for two access types. This mixup will be removed on the way
to kernel 6.6. In the future there will be two pairs of access functions. One for
classic access one for c45 style access. Rewrite our functions into 3 parts:
- a classic read/write function: ready for kernel 6.6
- a new c45 read/write function: ready for kernel 6.6
- a legacy read/write wrapper: for current 5.15 for the time being
When we switch to 6.6 we only need to remove the legacy wrappers and link the
new functions. Life can be so easy.
5. The classic read/write functions will incorporate the interception logic that
was originally in the patch.
6. The package convenience functions that were embedded in the patch get lost as
well. Rewrite them inside our phy driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[Minor checkpatch.pl cleanups]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
There is no need to keep a version specific dts directory.
Rename the folder to its standard location.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Apply changes suggested by SkyLake Huang for pending series improving
MediaTek Ethernet PHY drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Aruba boards now ship with multiple DTS and image-configurations per
image. Newer apboot revs expect a configuration for their hardware to be
present.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.
Fixes: e497c975d3 ("ramips: mt76x8: add support for Yuncore M300")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.
Fixes: 64dae1052b ("ramips: mt76x8: add support for Yuncore CPE200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
And remove support for 6.1 while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15838
Signed-off-by: Robert Marko <robimarko@gmail.com>
A rather trivial addition. Patches automatically rebased. Also add the new
CONFIG_USB_DWC3_OCTEON (disabled) to the generic 6.6 config and sort it, while
at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15838
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16103
Signed-off-by: Robert Marko <robimarko@gmail.com>
This enables the M.2 E-key on ROCK 5A board.
Reorder rk356x patch while at it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16340
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
This alias was present in 6.1. Add back to restore a fully working console after
sbi0 (earlycon) gets disabled during the boot process.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Various cleanups and bugfixes were applied.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16215
Signed-off-by: Robert Marko <robimarko@gmail.com>
No reason for them not to be so. Matches various upstream commits for
PPC.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>
With upstream commit 0aafbdf35c75cbfec82636d01e6dc7950bc1507c , this is
now default. No need to override.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit does this for simple cases, which all of these are.
Commit: 1c96fcdef8c7492ecf34ed70102a1ae5253ef9d1
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>
configure 2.5G PHY LEDs to:
2500/1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
which is similar to other 1G PHY LEDs, which are:
1000: green with blink on TX/RX
100/10: green+yellow with blink on TX/RX
Fixes: 6cc14bf66a ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Yan Cangang <nalanzeyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This commit adds the logic required to install OpenWrt on a
Cisco/Viptela vEdge 1000 while nicely integrating with the already
present bootloader and making it possible to roll back to stock OS.
The vEdge 1000 has a built-in SSD with a ext2 partition from which
the stock u-boot boots the Linux kernel from.
In order for Linux not to be confused about which partition the root
file system is on, there are some tricks needed to ensure the partition
is identifiable at boot time. For this we use blkid as part of the
scripts, and sfdisk as part of the manual installation process
documented on the wiki. Thus, those packages have been added as a
platform dependency. Finally, the u-boot environment is updated which
requires the use of uboot-envtools.
Tested on a Cisco vEdge 1000.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Link: https://github.com/openwrt/openwrt/pull/16140
Signed-off-by: Robert Marko <robimarko@gmail.com>
Yuncore CPE200 is an outdoor unit with IEEE 802.11ac radio.
Hardware:
- SoC: MediaTek MT7628DAN (MIPS 580MHz)
- Flash: 8 MiB Spansion S25FL064K
- RAM: 64 MiB (built-into SoC)
- WLAN: 5 GHz (MT7613AE)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- Buttons: 1 Reset button, 2 buttons for display UI (unsupported)
- LEDs: 4x Green (Power, LAN, WAN, WiFi)
- Display: 4 digit 7-segment display driven by an additional
microcontroller (unsupported)
- Serial console: unpopulated header, 57600 8n1 (RX only)
- Power: 12 VDC, 1 A
Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.0.100/ and upload sysupgrade.bin file.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
er is missing from platform_copy_config() and octeon_move_config(), so
config is lost on every sysupgrade.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/16238
Signed-off-by: Robert Marko <robimarko@gmail.com>
MediaTek SDK uses eth2 as additional LAN port and eth1 as WAN.
Do the same also in OpenWrt to keep settings aligned with the SDK.
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16057
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16057
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Unused wan mac added to dts. Requires DSA to implement.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16246
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get vlan 4k for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get mc index for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set and get ports speed for rtl8367d family chips
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Detect the RTL8367D chip family and set the appropriate extif
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/14804
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disables Data Center Bridging support for some network drivers by
default to avoid compilation errors when CONFIG_DCB is enabled.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3B is a Pico-ITX form factor SBC[1] using the Rockchip
RK3568(J).
Hardware
--------
- Rockchip RK3568(J) SoC
- Quad A55 CPU
- Mali-G52 GPU
- 1 TOPS @ INT8 NPU
- 2GB/4GB/8GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key (2-lane PCIe 3.0)
- SPI Flash for bootloader
- 2x Gigabit ethernet port (one supports PoE with add-on PoE HAT)
- 1x M.2 E Key socket with SDIO, UART and USB interfaces
- 1x M.2 B Key socket with PCIe, SATA, and USB interfaces
- 1x SIM card socket
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST ports
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3b
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3C is a high-performance, low-cost SBC[1] using the
Rockchip RK3566.
Hardware
--------
- Rockchip RK3566 SoC
- Quad A55 CPU
- Mali-G52-2EE GPU
- 1 TOPS @ INT8 NPU
- 1GB/2GB/4GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key connector(2230) or M.2 Extension
board(2232/2260/2280)
- SATA through the Radxa Penta SATA HAT
- 1x Gigabit ethernet port(supports PoE with add-on PoE HAT)
- WiFi6/BT5.4 (not supported yet on OpenWrt)
- 1x USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- 1x USB 2.0 Type-A OTG port
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3c
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All boards using the deprecated uImage.FIT partition parser have
been migrated to the new fitblk driver. Drop the now no longer
needed partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
That patch title of 911-kobject_add_broadcast_uevent.patch has been
wrongly copied from 910-kobject_uevent.patch.
Change the description from "lib: add uevent_next_seqnum()" to
"lib: add broadcast_uevent()", so that the git history doesn't look
all weird when importing both patches to a git tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes model name in dts as below:
Radxa ROCK3 model A -> Radxa ROCK 3A
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16232
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Like x86, armsr is frequently virtualized, and is used for development
and debugging. Kernel messages should be more readily apparent by
default. This can be achieved by adding console=tty1 to the kernel
command line, enabling the console on a (possibly virtual) display and
keyboard, in addition to a serial port.
This also enables failsafe on tty1. Failsafe mode operates on consoles
known by the kernel, without regard to /etc/inittab.
armsr's /etc/inittab is also updated to specify tty1 instead of tty0.
tty1 is technically more correct: tty1 is the first virtual console,
where tty0 reflects the current active virtual console (which is likely
to be tty1).
This configuration matches x86, which is another target commonly used
for virtualization, development, and debugging in the same way. x86's
kernel command line had specified console=tty0, although console=tty1 is
more correct for the reasons given above. This also brings x86's kernel
command line console= into agreement with its /etc/inittab, which
already used tty1.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16213
Signed-off-by: Robert Marko <robimarko@gmail.com>
Found with coccinelle:
No need to set .owner here. The core will do it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16217
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link TD-W8968 v3 is an 300Mbps Wireless N USB ADSL2+ Modem Router based on
Broadcom BCM6318 SoC.
Hardware:
CPU: Broadcom BCM6318, 333 MHz, 1 core
Flash: 8MB
RAM: 64 MB
Ethernet: 4x 10/100 Mbps
Wireless: 802.11b/g/n, BCM43217
LEDs/Buttons: 10x / 3x
USB: 1x 2.0
Flash instructions:
* Assign static IP 192.168.1.100 to PC
* Unplug the power source
* Press the RESET button at the router, don't release it yet!
* Plug the power source. Wait for some seconds
* Release the RESET button
* Browse to http://192.168.1.1
* Upload the openwrt-bmips-bcm6318-tp-link_td-w8968-v3-squashfs-cfe.bin file
* Wait some minutes until the firmware upgrade finish.
Signed-off-by: Mathesh Velayudan <123v.mathesh@gmail.com>
Device support for Sophos AP15 is based on Sophos AP55(C) and AP100(C).
Those other Sophos access points uss a QCA9558 SoC (some of them with
one of the three chains on the built-in SoC's wifi disabled) while the
AP15 uses a QCA9557 SoC (which only has two chains enabled in the
package or silicon).
This is mostly cosmetic since QCA9558 and QCA9557 are virtually
identical and all differences are automatically detected and/or managed
by the ART calibration.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/16187
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16230
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit introduces led nodes in tl-wdr4900-v1 dts.
It allows to configure switch leds from userspace.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link tl-wdr4900-v1 has two usb leds. Modern kernels can handle usb
led trigger. Let's enable it.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit change led description in dts file from old method to new
approach accepted by upstream.
USB power gpio is handled by gpio-export now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
Ever since CONFIG_ARM64_PAN was enabled Common Not Private (CNP) is now
visible and kernel builds will stop as they are not set in kernel config
for 5.15 and 6.1.
So, lets enable Common Not Private (CNP) which is ARMv8.2 feature and will
be NOP of CPU-s that dont support it.
Fixes: a2662309aa ("kernel: Enable CONFIG_ARM64_PAN to restrict kernel access to user space memory")
Link: https://github.com/openwrt/openwrt/pull/16211
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enhanced Privileged Access Never (EPAN) is an ARMv8.7 feature, and since
we dont have any SoC-s implementing it lets disable it.
Link: https://github.com/openwrt/openwrt/pull/16211
Signed-off-by: Robert Marko <robimarko@gmail.com>
The commit backporting new MTK patches did not update the
Kernel config for mediatek/mt7622 causing the build to
fail.
Simply use the new config symbol name for the driver to
fix the issue.
Fixes: 1069514978 ("mediatek: backport pending Ethernet PHY driver patches")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/16225
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use pending patchset for 2.5GE PHY driver, unifying LED handling
accross all MediaTek Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kconfig symbols CONFIG_ARM64_CNP and CONFIG_ARM64_EPAN got exposed
by enabling CONFIG_ARM64_PAN. Enable them as well, as just like for
PAN, also EPAN and CNP will be detected at runtime at no cost.
Fixes: a2662309aa ("kernel: Enable CONFIG_ARM64_PAN to restrict kernel access to user space memory")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
No benefit in doing so in platform file. Code for dts has already been
written. Might as well use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated. No need for any of this.
Calibration size was adjusted to 440, which is the standard value for
ath9k radios.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that the ports are defined in DTS, this is trivial to do.
Avoids userspace handling.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
The kernel support necessary to use a console keyboard was not built on
x86, affecting real and virtual machines alike. The console keyboard
would function properly in GRUB, but would not work at all once Linux
booted. It appeared that the console was intended to work because
console video appeared on the display, including prompts to enter
failsafe or select the debug log level from the keyboard, and the prompt
to "Press Enter to activate this console", but there was no way to
provide input to it. All keystrokes were ignored.
This enables several kernel configuration options to enable HID and USB
HID support (CONFIG_HID, CONFIG_HID_SUPPORT, CONFIG_HID_GENERIC, and
CONFIG_USB_HID), making the keyboard functional. For alignment with
armsr, CONFIG_USB_HIDDEV is also added, although not strictly necessary
for keyboard support. Note that this change also causes
CONFIG_HID_HYPERV_MOUSE to be enabled for x86/64 and x86/generic: it was
already set in these subarchitectures' kernel configurations, but was
ineffective due to CONFIG_HID being absent.
The omission of keyboard support on x86 may not have been widely noticed
because USB HID is not used on production OpenWrt x86 machines such as
pc-engines,apu2 which only have a serial console, or with the default
x86 configuration used by scripts/qemustart, which uses -nographic and
does not configure a virtual physical console but instead uses a serial
console.
This configuration change results in, for x86_64, +40kB in kernel.bin
and just over +40kB in gzip-compressed "combined" images. This should
not be a problem for the non-storage-constrained x86 target.
Until 2a86425de1, CONFIG_HID, CONFIG_USB_HID, and CONFIG_USB_HIDDEV
were set in the target-level kernel configuration, and
CONFIG_HID_GENERIC was set at the subtarget level. These are
reintroduced strictly at the subtarget level by request. This applies to
the 64, generic, and legacy subtargets, omitting geode.
Fixes: https://github.com/openwrt/openwrt/issues/16157
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16208
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable the CONFIG_ARM64_PAN kernel security option, which leverages the
ARMv8.1 Privileged Access Never (PAN) extension to prevent the kernel
from directly accessing user space memory.
Instead, copy_to_user and similar functions must be used for data
transfer between kernel and user space. This feature is automatically
disabled at runtime on CPUs without PAN support, making it a no-op in
those cases.
Link: https://github.com/openwrt/openwrt/pull/16189
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Activate the kernel option CONFIG_LIST_HARDENED for all targets.
This adds some inline checks to list_add() and list_del() operations
in the kernel. Before kernel 6.6 these checks were only available with
CONFIG_DEBUG_LIST option, but now a light version is available which
should only add very few extra instructions to such operations.
The performance penalty is very low from my point of view. It should
make it much harder to use bugs in Linux kernel list handling when
exploiting the Linux kernel.
Link: https://github.com/openwrt/openwrt/pull/16189
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
2500 Base-T
RGB LED
eMMC Connector
SPI-NOR 16MB
Micro-SD Slot
2x USB 2.0 Port
2x USB 3.0 Port
Headphone Jack
M.2 E-Key
M.2 M-Key
USB PD 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
1000 Base-T
Status LED
eMMC/SPI Connector
Micro-SD Slot
2x USB 3.0 Port
2x USB 2.0 Port
Headphone Jack
M.2 E-Key
USB PD/QC 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now we have rk3588 support :)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit f98f95359b.
It seems that this commit is causing issues with the PWM fan on the RPi 5 as
reported here: https://github.com/openwrt/openwrt/issues/16191
So let's revert this for now.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The D-Link DSL-2750B rev B1 (AW4339U) is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.
This ports the device from old target bcm63xx/generic to bmips/bcm6328.
The hardware is the same of D-Link DSL-2740B rev F1 and DSL-2741B rev F1, plus a usb2 port.
Hardware:
- SoC: Broadcom BCM63281
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB (Nanya NT5TU32M16DG)
- Flash: 8 MB NOR (Macronix MX25L6406ENI-12G)
- Ethernet LAN: 4x 100Mbit (Broadcom BCM63281)
- Wifi 2.4 GHz: 802.11bgn (Atheros AR9287)
- USB: 1x 2.0
- Buttons: 3x
- LEDs: 10x
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Samuele Longhi <agave@dracaena.it>
It's upstream and a replacement for the swconfig driver.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16124
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allows removing free_irq. Simpler.
Oddly enough the other switch code already does this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16050
Signed-off-by: Robert Marko <robimarko@gmail.com>
