This reverts commit f98f95359b.
It seems that this commit is causing issues with the PWM fan on the RPi 5 as
reported here: https://github.com/openwrt/openwrt/issues/16191
So let's revert this for now.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The D-Link DSL-2750B rev B1 (AW4339U) is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.
This ports the device from old target bcm63xx/generic to bmips/bcm6328.
The hardware is the same of D-Link DSL-2740B rev F1 and DSL-2741B rev F1, plus a usb2 port.
Hardware:
- SoC: Broadcom BCM63281
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB (Nanya NT5TU32M16DG)
- Flash: 8 MB NOR (Macronix MX25L6406ENI-12G)
- Ethernet LAN: 4x 100Mbit (Broadcom BCM63281)
- Wifi 2.4 GHz: 802.11bgn (Atheros AR9287)
- USB: 1x 2.0
- Buttons: 3x
- LEDs: 10x
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Samuele Longhi <agave@dracaena.it>
It's upstream and a replacement for the swconfig driver.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16124
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allows removing free_irq. Simpler.
Oddly enough the other switch code already does this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16050
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware:
- SoC: MediaTek MT7628DAN (MIPS 580MHz)
- Flash: 8 MiB Spansion S25FL064K
- RAM: 64 MiB (built-into SoC)
- WLAN: 2.4 GHz (MT7628)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- Buttons: 1 Reset button
- LEDs: 1x Red, 1x Green
- Serial console: unpopulated header, 57600 8n1 (RX only)
- Power: 12 VDC, 1 A
There are unpopulated areas on the board for 5 GHz WiFi via PCIe as well
as (most likely) Quectel EG25-G 4G module. As both are not populated on
my board support for both is missing for now.
Installation:
The installation can be done via the recovery HTTP server which is built
into the bootloader. Hold down the reset button while connecting the
device to power and keep holding a bit more than 3 seconds. Connect to
http://192.168.188.253/ and upload sysupgrade.bin file.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the KERNEL_BTRFS_FS config option so that targets can select
whether BTRFS support must be built-in.
Select this option (alongside KERNEL_BTRFS_FS_POSIX_ACL) from the
layerscape/armv8_64b subtarget instead of enabling it in
target/linux/layerscape/armv8_64b/config-* files.
Move disabling of CONFIG_BTRFS_FS_CHECK_INTEGRITY into generic configs.
This makes it possible for OpenWRT to be built with built-in BTRFS
support on specific boards, instead of whole targets.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/15990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
- MT7629 CPU
- MT7531 switch
- MT7761N and MT7762N wifi
- 256 MB RAM
- 128 MB NAND flash with dual-boot partitions
- 2 buttons: WPS and reset
- 1 WAN port (1G)
- 4 LAN ports (1G)
- 1 USB port
Limitations (same as other MT7629/MT7761N/MT7762N devices):
- Wifi is not working
- Second core is not working (kernel error message "CPU1: failed to come online")
Disassembly:
- There are two screws under the front rubber feet and two under the label on the bottom (in the corners towards the back, you should be able to feel them).
Serial Interface:
- UART pin header is already soldered on the board. Pinning from front to back:
1 - VCC
2 - TX
3 - RX
4 - n/a
5 - GND
GPIO:
- 1 white LED, connected to GPIO 52
- 1 reset button, connected to GPIO 60
- 1 WPS button, connected to GPIO 58
MAC Adresses:
- The MAC address printed on the device label is used for LAN and WAN
- The MAC address is stored in the devinfo partition in ASCII format (hw_mac_addr=aa:bb:cc:dd:ee)
- 2.4 GHz wifi uses MAC of the device label + 1
- 5 GHz wifi uses MAC of the device label + 2
Flashing:
- OpenWrt is only runnig in the first partition of dual boot
- To ensure to be able to go back to the factory image, flash the last OEM firmware via OEM web interface. This will ensure that the OEM firmware is present on both partitions
- Because of dual boot partitions, flashing via OEM interface is not supported
- Start a TFTP server and provide the initramfs image. Default settings:
- Router IP: 192.168.1.1
- TFTP server IP: 192.168.1.100
- TFTP file name: 7531.bin
- Open the device, connect UART and select " 1. System Load Linux to SDRAM via TFTP." during startup
- Adapt the settings to your environment, if required
- After initramfs is booted, flash the sysupgrade image
Return to OEM firmware:
- Run the following commands in OpenWrt to switch to the second partition
fw_setenv boot_part 2
fw_setenv bootimage 2
- Reboot the device. OEM firmware will start up again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16067
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SUPPORTED_DEVICES is required for Radxa ROCK Pi S.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the LED definitons for the XG6846 DSA port LEDs.
These are standard properties compatible with the existing
Marvell 88e6xxx DT bindings and fully standardized so this
is fine to add. They will be used by the in-flight Marvell
88e6xxx LEDs support patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[add empty lines between leds, remove default-state="off"]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
For some troublesome devices it is necessary to obtain direct access
to the SFP module EEPROM so define it in the device tree.
Suggested-by: Paul Donald <newtwen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some versions of the Inteno XG6846 has a USB port mounted.
For these machines the corresponing USB port nodes need to
be enabled.
Suggested-by: Henrik Ginstmark <henrik@ginstmark.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[reorder DTS alphabetically]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
997acc7f86 split this PHY driver up such
that external QCA switches now use CONFIG_QCA83XX_PHY. Fix it here so
that ethernet works again.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16154
Signed-off-by: Robert Marko <robimarko@gmail.com>
The second edition of international version of Mi Router 4A 100M is
very similar to the non-international one, but has another wireless chip.
Installation
--------------
1. Initialize build-in firmware (use webgui for 192.168.31.1)
You should install root password
2. Run OpenWRTInvasion for the first time (probably it will fail)
Version 0.0.10 is working as well as 0.0.1.
3. Run OpenWRTInvasion for the second time
It will create an access to your router
4. Upload sysupgrade image to router (/tmp/fw.bin)
pc# nc -l 8080 < …/ramips/mt76x8/…-100m-intl-v2-squashfs-sysupgrade.bin
router# nc 192.168.31.175 8080 > /tmp/fw.bin
5. Flash new firmware
router# run mtd -r write /tmp/fw.bin OS1
6. Check result
Wait about 5-10 minutes after flash. Router should reboot itself and
turn left led from orange to blue.
In case of failure one can use Xiaomi 4a 100m debrick tool
(it uploads special image via tftpd in recovery mode)
After that you can start again from step 1.
Another actions are very similar to original Mi Router 4A 100M
Original mtd paritions:
-------------------------
```
Creating 9 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000020000 : "Bootloader"
0x000000020000-0x000000030000 : "Config"
0x000000030000-0x000000040000 : "Factory"
0x000000040000-0x000000050000 : "crash"
0x000000050000-0x000000060000 : "cfg_bak"
0x000000060000-0x000000160000 : "overlay"
0x000000160000-0x000000dc0000 : "OS1"
0x000000dc0000-0x000001000000 : "disk"
with special sub-partition
0x0000002c0000-0x000000dc0000 : "rootfs"
```
We will use OS1+disk space:
```
0x000000160000-0x000001000000 : "firmware"
```
Co-authored-by: Nita Vesa <nita.vesa@elektrik.link>
Signed-off-by: Anton Stratonnikov <billic@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/14304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NVMEM is the upstream replacement for this. ralink,mtd-eeprom is
deprecated. The others need to stay as there's byte swapping going on.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16084
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also migrate mt7623 to new fitblk support scripts which simplify
sysupgrade when using uImage.FIT. This had been forgotten previously.
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Simplifies the code by removing clk_disable_unprepare.
Also removed gotos and used dev_err_probe.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16133
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a use-after-free bug in mtk_wed_setup_tc_block_cb()
which leads to kernel panic when setup multiple ap
interfaces on one band of mt798x.
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16118
Signed-off-by: Robert Marko <robimarko@gmail.com>
Read the 'fip' static volume in order to trigger scrubbing in case of
detecting flipped bits while reading.
We have to do this in Linux because we never read or touch the 'fip'
volume and the UBISPL implementation in ARM TrustedFirmware-A does NOT
handle scrubbing itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reporting an unclean read from SPI-NAND only when the maximum number
of correctable bitflip errors has been hit seems a bit late.
UBI LEB scrubbing, which depends on the lower MTD device reporting
correctable bitflips, then only kicks in when it's almost too late.
Set bitflip_threshold to 75% of the ECC strength, which is also the
default for raw NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It seems that some Xiaomi AX3000T boards changed to using Winbond W25N01KV
SPI-NAND which is not supported in OpenWrt nor upstream kernel.
So, add a pending patch to support it as upstream supports rest of the KV
revision models.
Fixes: #16002
Link: https://github.com/openwrt/openwrt/pull/16088
Signed-off-by: Robert Marko <robimarko@gmail.com>
We need to configure the led and network config for this board on
start as per the others
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches for the nanopi r6s board, backporting from 6.9 where
basic support is landing.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.
Hardware:
Model: Cambium Networks XE3-4
CPU: IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
Memory: 1 GiB
Flash: 512 MiB Macronix MX30UF2G18AC + W25Q128FW
Ethernet: 1x 1 GbE (QCA8072)
1x 2.5 GbE (QCA8081)
Buttons: 1x Reset
Serial: TX, RX, GND
Baudrate: 115200
Radios: Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
BLE 4.1
Power: 32.0W 802.3bt5 PoE++
25.5W 802.3at with USB, BT disabled
Size: 215mm x 215mm
Ports: 1x USB 2.0
Antenna: 6 GHz: 6.29 dBi, Omni 30 dBm
5 GHz: 6.12 dBi, Omni 31 dBm
2.4 GHz: 4.85 dBi, Omni 29 dBm
LEDs: Multi-color status LEDs
Mounting: Wall, ceiling or T-bar
Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
one of the APs GND pins.
3. Transfer the initramfs image with TFTP
(Default server IP is 192.168.0.120)
# tftpboot factory.ubi
4. Flash the rootfs partition
# flash rootfs
5. Reboot the AP
# reset
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15633
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes the image check failed on system upgrade
"Image check failed:
upgrade: Device radxa,rock3a not supported by this image
upgrade: Supported devices: radxa,rock-3a"
Signed-off-by: Tomas Lara <tl849670@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to RTL8221B's datasheet, the PHY requires at least 10ms
for assert and 68ms (recommended) for de-assert. So increase the
assert/de-assert time to 15ms and 68ms respectively.
Fixes: c0c3234e17 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16106
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refactor Inteno XG6846 device tree to be in line with other bmips devices.
Also expose USB LED automatically.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Enable CONFIG_HWMON and CONFIG_THERMAL_HWMON on all subtargets.
- Drop kmod-thermal from bcm2712.
- Add CONFIG_SENSORS_RASPBERRYPI_HWMON generic symbol.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
target/linux/archs38/image/Makefile calls gen_axs10x_sdcard_img.sh
with $(CONFIG_TARGET_ROOTFS_PARTSIZE).
Make sure a rootfs partition is built and usable.
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Link: https://github.com/openwrt/openwrt/pull/16098
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ec885796c0 switched the crc32 implementation from default to
byte-at-a-time algorithm, which runs slower but consumes less memory.
A decade has passed, and we have already abandoned targets that had
small memory, so switch it back to default for faster speed.
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Enable the CONFIG_MTD_SPI_NOR_USE_VARIABLE_ERASE kernel option to allow for
U-Boot environment writing. This might be hiding a problem somewhere else,
since the w25q128fw chip supports 32K erases, still this change makes it
much easier to switch the GL-MV1000 boot media without an UART cable
connection.
Thanks to @robimarko and @hacks for the precious hints and suggesting a
better approach.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
This allows booting from internal eMMC or SD card just changing the
U-Boot mmc_dev variable.
In particular, setting mmc_dev to 1 will result in booting from the SD card.
Setting the variable to 0 will result in internal eMMC boot (the default).
Should the variable be unset or an error condition occur while reading
from SD card, internal MMC booting will be tried.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
mpc85xx was switched to 6.6. We can remove 6.1 support now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16087
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's time for wide tests.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16087
Signed-off-by: Robert Marko <robimarko@gmail.com>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.44..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds auto-configuration of network ports on Dell EMC Edge620 (x86) product.
It is similar in specs/features to some of the Sophos x86-based appliances, but:
1. Serial console terminal is built in and requires just the micro-USB cable
2. Comes with both MMC (16Gb) and SSD (256Gb) installed
3. Comes with 6 ethernet ports all 6 are functional when no SFP is used
4. Comes with two SFP cages and not one, like some of revision 3 Sophos products
5. Unlike Sophos devices, there are no non-wireless models of Edge 620,
it comes with Qualcomm Atheros QCA9880 radio
These devices can be now found both second-hand and new at online marketplaces below
(sometimes well below) US $100, I believe they make great candidates for running OpenWrt.
The ethernet network ports on the case are marked GE1 thru to GE6 with the
following mapping once booted into OpenWrt:
```
GE1: eth2: pci0000:00/0000:00:0b.0/0000:02:00.2
GE2: eth3: pci0000:00/0000:00:0b.0/0000:02:00.3
GE3: eth0: pci0000:00/0000:00:0b.0/0000:02:00.0
GE4: eth1: pci0000:00/0000:00:0b.0/0000:02:00.1
GE5: eth7: pci0000:00/0000:00:17.0/0000:07:00.1
GE6: eth6: pci0000:00/0000:00:17.0/0000:07:00.0
```
Dell's instructions for [standard configuration](https://infohub.delltechnologies.com/en-us/l/dell-emc-edge-620-advanced-activation-guide/dell-emc-sd-wan-edge-620-standard-configuration/)
recommend using GE3, GE4, GE5, or GE6 for WAN, I've selected the GE6 as the sole
WAN port under OpenWrt with the rest of ethernet ports assigned to LAN.
Please merge before 24.xx is forked and if possible, cherry-pick for 23.05
if there's no ETA for 24.xx forking.
PS. @Hurricos I'm struggling with ixgbe mappings on Sophos devices which use
very similar hardware to Dell EMC, so even tho I know the sys paths for ethernet ports,
I'd prefer to do a separate commit to properly map ethernet ports to match the case markings
for this device at some point later.
Signed-off-by: Stan Grishin <stangri@melmac.ca>
Use realtek,extif property instead of realtek,extif0 to extif2
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Store the chip type in smi->rtl8367b_chip
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove the rlvid analysis because for the rtl8367b family chips supported
by the driver (rtl8367rb and rtl8367r-vb), rlvid is always equal to 1.
So the code for rlvid equal to 0 is completely unnecessary.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use realtek,extif property instead of realtek,extif0 and realtek,extif1
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop config for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16030
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16030
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new utility, omnia-mcutool, which main purpose is to upgrade the
firmware on the microcontroller on the Turris Omnia router. Depends on
omnia-mcu-firmware, and the upgrade process is pretty simple:
omnia-mcutool --upgrade
Besides firmware upgrade, the utility can be used to show and configure
various firmware settings.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new package, omnia-mcu-firmware, containing firmware binaries for
the microcontroller on the Turris Omnia router.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the MCU driver on CZ.NIC's Turris Omnia. This adds
the ability to do a true board poweroff, and to configure various
features (for example the user may configure that after poweroff, the
router should automatically wake up at a specific time).
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
This backports patches
dt-bindings: firmware: add cznic,turris-omnia-mcu binding
platform: cznic: Add preliminary support for Turris Omnia MCU
platform: cznic: turris-omnia-mcu: Add support for MCU connected GPIOs
platform: cznic: turris-omnia-mcu: Add support for poweroff and wakeup
platform: cznic: turris-omnia-mcu: Add support for MCU watchdog
platform: cznic: turris-omnia-mcu: Add support for MCU provided TRNG
ARM: dts: turris-omnia: Add MCU system-controller node
ARM: dts: turris-omnia: Add GPIO key node for front button
platform: cznic: turris-omnia-mcu: Depend on OF
platform: cznic: turris-omnia-mcu: Depend on WATCHDOG
platform: cznic: turris-omnia-mcu: fix Kconfig dependencies
that will be released in 6.11 into mvebu/patches-6.6.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
This target doesn't actually use NAND.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16001
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit f444dea428.
It seems that some devices using GPIO WDT have really short WDT timeouts
and when using module_platform_driver registration it happens too late
and thus WDT will timeout and reset the board.
So, for now lets return the postcore_initcall hack for now.
Fixes: f444dea428 ("ath79: remove GPIO driver earlier registration hack")
Signed-off-by: Joan Moreau <jom@grosjo.net>
Link: https://github.com/openwrt/openwrt/pull/16035
Signed-off-by: Robert Marko <robimarko@gmail.com>
Layerscape was switched to 6.6 kernel. Now is time to remove 6.1
support.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16037
Signed-off-by: Robert Marko <robimarko@gmail.com>
CI says patches need to be refreshed, so do so.
Fixes: 6bb334c5cf ("mediatek: fix u-boot env layout NVMEM definitions")
Link: https://github.com/openwrt/openwrt/pull/16051
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kirkwood was switched to 6.6. We can remove 6.1 support now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
generic.mk was commited by mistake. It isn't used. Let's remove it.
Fixes: ccbdb212f3 ("kirkwood: Add missing package dependency")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
Let's switch to kernel 6.6 for wide tests.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
Radxa ROCK Pi E v3.0 has a RTL8723DU Wi-Fi 4 on-board device. enable
it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S has a RTL8723DS Wi-Fi 4 on-board device. enable it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Import patch from mainline Linux to fix issue with PERST# signal
polarity.
Quote from commit message:
"This extra, very short, PERST# assertion + deassertion has been
reported to cause issues with certain WLAN controllers, e.g. RTL8822CE."
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Testing turned out that the HWRNG quality varies greatly on RK3566,
even on supposedly identical boards and SoC revisions.
Hence enable the HWRNG driver only on RK3568 for now.
Allow users to simply tune sample_count and quality to allow easily
testing results on different boards and SoCs.
Link: https://patchwork.kernel.org/project/linux-arm-kernel/cover/cover.1720969799.git.daniel@makrotopia.org/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a backport of netdev/net [1]/[2], expected to be in kernel 6.11
(if not backported to a stable branch).
Since 4fdc7bb8f1 (2024-06-14, switching ath79 from kernel 6.1 to 6.6),
the rtl8366s driver was made to write to bogus PHY MII registers on
ath79/netgear,wndr3800 and family, and likely on other systems using
this switch in a similar manner. The writes were directed to PHY 4 MII
registers 0x0d (13) and 0x0e (14). The rtl8366s data sheet claims these
registers are reserved. These register writes were causing the device to
not maintain link, track link status, or pass traffic on eth1 (labeled
WAN), as eth1 is connected to PHY 4.
0x0d is MII_MMD_CTRL, and 0x0e is MII_MMD_DATA. rtl8366s doesn't appear
to support MMD in any way, and certainly not via the IEEE 802.3 annex
22D "clause 45 over clause 22" protocol implemented by mmd_phy_indirect.
This patch intercepts those attempted register accesses and returns
-EOPNOTSUPP without touching the switch chip. This is implemented by
defining phy_driver::{read,write}_mmd as
genphy_{read,write}_mmd_unsupported for this PHY. A new PHY driver for
this PHY is introduced to achieve that, because this PHY was previously
using genphy_driver, and there is otherwise no clean way to declare lack
of support for these operations.
This was caused by kernel 9b01c885be36 (2023-02-13, in 6.3). The new
genphy_c45_read_eee_abilities call in genphy_read_abilities (called
during phy_probe) was causing an attempted MMD read of (MMIO_MMD_PCS,
MDIO_PCS_EEE_ABLE), which was transformed into an annex 22D
mmd_phy_indirect operation that performed MII register writes to
MII_MMD_CTRL, MII_MMD_DATA, and MII_MMD_CTRL again, followed by another
read from MII_MMD_DATA. This was enough to "scramble" the state of those
two MII registers, which are in fact not used for annex 22D MMD register
access on this device but are reserved and have some other function,
rendering the PHY unusable while so configured. The result of the
bungled MMD read attempt caused the genphy driver to incorrectly believe
that the PHY supported standard EEE, which led to several more attempted
MMD writes and reads, in turn being transformed into writes to these two
MII registers.
rtl8366s does support some pre-IEEE 802.3az EEE standard form of "Green
Ethernet" which the switch driver (local to OpenWrt) already has some
support for. No attempt is made to map the standard operations for this
device.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=225990c487c1
[2] https://lore.kernel.org/netdev/20240725204147.69730-1-mark@mentovai.com/
Fixes: https://github.com/openwrt/openwrt/issues/15981
Link: https://github.com/openwrt/openwrt/issues/15739
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16012
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi E v3.0 is a compact networking SBC[1] using the Rockchip
RK3328 SoC.
Hardware
--------
- Rockchip RK3328 SoC
- Quad A53 CPU
- 512MB/1GB/2GB DDR4 RAM
- 4/8/16/32GB eMMC
- Micro SD Card slot
- WiFi 4 and BT 4, or WiFi 5 and BT 5 (not supported yet)
- 1x 1000M Ethernet with PoE support (additional PoE HAT required)
- 1x 100M Ethernet
- 1x USB 3.0 Type-A port (Host)
- 1x 4-ring 3.5mm headphone jack
- 40 Pin GPIO header
[1] https://radxa.com/products/rockpi/pie
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15984
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
The hardware of these two models looks the same. This patch also
disabled unused i2c bus for WE3526.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
From the kernel log, we are using PCIe port 1 and 2.
dmesg:
```
[ 0.963526] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[ 0.970432] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 0.975312] mt7621-pci 1e140000.pcie: PCIE2 enabled
[ 1.071442] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[ 1.130382] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
```
Fixes: https://github.com/openwrt/openwrt/issues/16000
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for a dual-band AX1800 wall plug manufactured
by Shenzhen Century Xinyang Tech Co., Ltd.
CPU: Mediatek MT7621A (2 cores, 4 threads)
RAM: 256i MiB DDR3 (Samsung K4B2G1646F-BCNB)
ROM: 16 MiB SPI NOR (Winbond W25Q128JVPQ)
Wired: one gigabit RJ45 port (with green/yellow non-GPIO LEDs)
WiFi: Mediatek MT7905DAN + MT7975DN (DBDC 2x 2T2R)
Ant.: four 2 dBi external antennas (two 2.4GHz, two 5 GHz)
GPIO: tri-color status LED (GPIO 13, 14, 16);
reset button (GPIO 18)
Power: 12V 2-pin JST-XH on main PCB
110/220V AC to 12V1A DC on auxiliary PCB
UART: 115200 8n1, SMD pads available on the PCB as J4
pinout is [3v3] (Rx) (Tx) (Gnd)
MAC: 1C:BF:CE:xx:xx:xx (2.4 GHz, label)
1C:BF:CE:xx:xx:xx + 1 (ethernet [1])
1C:BF:CE:xx:xx:xx + 2 (5 GHz)
Original firmware is LEDE Reboot 17.01-SNAPSHOT (kernel 4.4.198)
with a few custom packages and a non-LuCI web interface.
Telnet and SSH are enabled, requiring an unknown root password [2].
Root password is also needed to access the router via UART console,
but passwordless telnet can be enabled via a trivial web exploit [3]
and then the root password can be removed by editing `/etc/shadow`.
Installation: First upload `sysupgrade` binary via web interface at
`http://192.168.188.1/settings.shtml` and wait until getting back to
the home screen (select network to extend). The installation fails
since the original firmware uses `swconfig` and recent versions of
OpenWrt use DSA. However, the sysupgrade file is uploaded correctly
and stored at `/tmp/upgrade.bin`, so it can be written to flash via
the web exploit [4] (both `mtd -r write` and `sysupgrade -Fn` work
fine). Passwordless telnet/ssh is not needed for installation.
Alternatively, use u-boot menu to load image via TFTP.
Notes:
- Device model in LEDE is "MediaTek MT7621 RFB (802.11ax,SNOR)".
- It is sold under several names, among them are Wodesys WD-R1802U,
Fenvi F-AX1802U, and EDUP EP-2971; the Wodesys brand was selected
since it is referenced in `/etc/banner` and `/etc/hosts`, and the
PCB is marked "WD518A V1.0".
- Instead of a standard ethernet transformer, the PCB has a few tiny
SMD coils.
[1] Original firmware sets ethernet MAC to 1C:BF:CE:E7:62:1D based on
offset `0x3fff4` in the Factory partition; since this is the same
MAC for all units, whereas WiFi MACs stored at offsets 0x6 and 0xc
are unique, it was decided to use <label MAC + 1> for ethernet.
[2] root:$1$7rmMiPJj$91iv9LWhfkZE/t7aCBdo.0:18388:0:99999:7:::
[3] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;killall telnetd;telnetd -l /bin/sh"
[4] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;mtd -r write /tmp/upgrade.bin firmware"
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15777
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport H616 DVFS support from linux-next.
Tested on the Orange Pi Zero 3 (H618 SoC).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15600
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Freescale procesor has Securite Engine driver called Talitos. [1]
This driver is already packaged for OpenWrt since commit
bf57f33f02 ("kernel: Allow talitos crypto
hw module selection"), but many users don't know about it.
Let's include this kernel module package to default packages as it was
recently done for MediaTek in commit 06c4fc6d5e
("kernel: enable inside secure driver for MediaTek platforms")
[1] https://cateee.net/lkddb/web-lkddb/CRYPTO_DEV_TALITOS.html
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/10557
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some devices lock up on PCIe initialization:
[ 64.309697] PCIe: Port 0 in endpoint mode, skipping.
[ 64.320496] PCIe: Initializing port 1
[ 64.325257] PCIe: BIST FAILED for port 1 (0xffffffffffffffff)
(system hangs here)
Given the ER contains no PCIe peripherals, has no way to attach any
and the stock kernel doesn't have PCIe support either, just disable it.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/15992
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16021
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16021
Signed-off-by: Robert Marko <robimarko@gmail.com>
NEC Aterm WG600HP is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG600HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG600HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : A4:12:42:xx:xx:A0 (config, 0x6 (hex))
WAN : A4:12:42:xx:xx:A1 (config, 0xc (hex))
2.4 GHz: A4:12:42:xx:xx:A2 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : A4:12:42:xx:xx:A3 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WR9500N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, Atheros AR9344 (SoC)
- 5 GHz : 3T3R, Atheros AR9380
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 12x/4x
- note : all LEDs are controlled by ath9k chip (AR9380)
- UART : pad on PCB (near shielded ath9k chip, white circle)
- assignment : 3.3V, GND, TX, RX from AR8327 side
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR9500N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR9500N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9380) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:60 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:61 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:62 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:63 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WR8750N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR8750N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR8750N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:00 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:01 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:02 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:03 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix PCIe initialization on AR934x by clearing PLL_PWD bit in addition to
PPL(PLL?)_RESET bit of AR724x.
Refresh patches by `make target/linux/refresh`.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The archs38 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix uninitialized variable warnings in function regcache_maple_drop
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel config for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT40A512M16TB-062ER 1GB
Ethernet: 2x 2.5G, 4x 1G Lan
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5.2GHz 4T4R
WiFi3: MT7915AN 5.8GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 5A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).
Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)
Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.
Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Radxa ROCK Pi S is a small in size, full in features SBC[1] using the
Rockchip RK3308B SoC.
Hardware
--------
- Rockchip RK3308B SoC
- Quad A35 CPU
- 256/512MB DDR3 RAM
- Optional 4/8GB eMMC
- Micro SD Card slot
- Optional WiFi 4 and BT 4 (not supported yet)
- 1x 100M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 2.0 Type-A port (Host)
- 1x USB 2.0 Type-C port (OTG)
- 2x 26 Pin GPIO header
[1] https://radxa.com/products/rockpi/pis
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Keenetic KN-3510 is a 2.4/5 Ghz band 11ax access point
Specification:
- System-On-Chip: MT7621AT
- CPU/Speed: 880 MHz
- Flash-Chip: Macronix MX30LF1G28AD-TI
- Flash size: 128 MiB
- RAM: 256 MiB
- 2x 10/100/1000 Mbps Ethernet
- PoE, 802.3af/at
- 4x internal antennas
- UART (J1) header on PCB (115200 8n1)
- WiFi: MT7915 2x2 2.4G 573.5Mbps + 2x2 5G 1201Mbps
- 2x LED, 2x button, 1x mode switch
Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3510-squashfs-factory.bin"
to "KN-3510_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is exactly the same as WL-WN531G3 but with different partition layout and different MAC layout. Labeled as Quantum D4G Rev.: A2.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x Touchlink button
- 1x Turbo button
- 1x Wps button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 5x Blue leds (ethernet ports)
- 1x Power led
- 1x Wifi led
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:0F (factory @ 0x28)
WAN XX:XX:XX:XX:XX:10 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:11 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:12 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:11
Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15876
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In make menuconfig the name is [Amplifi Router HD], and
is missing Ubiquiti. Lets fix that by adding
DEVICE_VENDOR := Ubiquiti to generic-ubnt.mk so the name is:
[Ubiquiti Amplifi Router HD].
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15932
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.
Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- radio0 (Wi-Fi 2.4GHz) = label MAC + 1
- radio1 (Wi-Fi 5GHz) = label MAC + 2
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP6X10XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap6010dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/15941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove kmod-switch-rtl8366-smi from the package list, as it is still loaded
because kmod-switch-rtl8367b depends on it
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15757
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit fixes all errors reported by the checkpatch script. This
should make it easier to accept upstream this patch.
There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes two issues in the driver detach:
* double free of the same descriptor (upstream bug, backported in 66177c081f),
* releasing tx descriptor instead of rx (downstream bug).
The driver is compiled into the kernel that is why the error
is not visible in normal use.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Switch to new nvmem binding.
Also fixes a issue that the MAC address assigned to lan/wan was
reversed on eMMC boards.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Also use env variables exported by export_fitblk_rootdev() in
platform_copy_config().
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The target was marked source-only due do the broken Ethernet port on
some devices. With that fixed, it can be enabled again.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The new cpsw-switch driver reserves VLAN 1 for internal use, which
conflicts with the default network configuration of OpenWrt.
Switch back to the older cpsw driver to make the network connection on
the affected devices (BeagleBone Black and AM335x EVM) usable again.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The eMMC chip used in a small batch of these devices has issues operating
in HS400 mode. Reducing to HS200 mode works around the problem and does
not cause any noticeable performance penalties as smaller chips are not fast
enough to saturate the bus. Root cause analysis is pending.
Signed-off-by: Chad Monroe <chad@monroe.io>
Add entry for the BananaPi R3 mini to the platform_check_image()
function where it has been missing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There is no reason not to wire up the default netdev trigger for the SFP
LED since we have a separate SFP interface visible.
Link: https://github.com/openwrt/openwrt/pull/15927
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since we are trying to get rid of using labels, lets convert RB5009 to the
function/color combo.
Link: https://github.com/openwrt/openwrt/pull/15927
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, QCA8081 LED is never configured and the default configuration
has the LED polarity inverted so it will be lit when there is nothing
connected to the PHY.
So lets define the LED as active-low and configure the trigger via 01_leds.
Fixes: 85d9fd6f0e ("mvebu: add support for RB5009UG+S+IN")
Link: https://github.com/openwrt/openwrt/pull/15927
Signed-off-by: Robert Marko <robimarko@gmail.com>
stop "heartbeat" which happens before OpenWrt controls LED. instead,
just turn LED on.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15913
Signed-off-by: Robert Marko <robimarko@gmail.com>
The switch to the upstream mmc-mtk driver caused problems with MT7621
because of unstable too high clock frequency:
[ 49.643291] mmc0: error -88 whilst initialising SD card
[ 49.890047] mmc0: error -88 whilst initialising SD card
[ 50.142414] mmc0: error -88 whilst initialising SD card
[ 50.419218] mmc0: error -88 whilst initialising SD card
...
Fix this by reducing the clock speed to 48 MHz instead of 50 MHz, which
is also the value used in upstream Linux mt7621.dtsi.
With that change applied SD cards work as expected on MT7621 devices
also with the new driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Override max clock frequency to a stable value 24 MHz.
2. Use voltage regulator to control the power supply.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Now that the SDHC of MT762{0,1,8} has been supported upstream, it's
time to switch the default driver to the upstream one. We will still
keep the old driver for users to choose from.
Tested on HiWiFi HC5861 (MT7620A) and HiWiFi HC5661A (MT7628N).
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add all essential MTK SDHC properties to support the new mmc-mtk
driver. Since this driver relies on power regulators, we also
need to enable this feature for MT7620, just like MT762{1,8}.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: John Thomson <git@johnthomson.fastmail.com.au>
This is the upstream implementation of the MTK SD/SDIO/MMC card
reader driver. It is an alternative solution for the downstream
driver package "kmod-sdhci-mt7620".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: John Thomson <git@johnthomson.fastmail.com.au>
"cd-inverted" is an upstream documented property used to indicate
the CD line is actived high. We will introduce a new upstream SDHC
driver, and this change will make them compatible with each other.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.38
Removed target/linux/generic/hack-6.6/900-fix-build-to-handle-return-value.patch
which was introduced as a hacky attempt to fix an upstream issue related to 6.6.37.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/15879
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the past few years, we have received several reports about SPI
Flash not working properly. This is caused by excessively fast
clock frequency. It's really annoying to fix them one by one. Let's
reduce these aggressive frequencies to 50 MHz. This is a safe and
suggested value in the vendor SDK.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This commit adds support for Asus RT-AX89X BX revision.
WARNING: Only the BX revision boards (So B1, B2 etc) are supported because
AX revision boards use IPQ8074 v1 SoC which is unsupported.
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53 @ 2.2GHz
* RAM: 1024MB
* Storage: 256MB SLC NAND (Macronix MX30UF2G18AC)
* Ethernet:
* 5x 1G RJ45 ports via QCA8337 switch
* 3x 1G RJ45 ports via internal switch (QCA8075 PHY)
* 1x 10G RJ45 via internal switch (AQR113C PHY)
* 1x 10G SFP+ slot via internal switch
* WLAN:
* 2.4GHz 4x4
* 5GHz 8x8
* 8 external antennas
* USB: 2x USB 3.0 Type-A
* Buttons:
* Power switch
* WPS
* Reset
* Wireless ON/OFF
* LED ON/OFF
LED-s:
* Power
* Wi-Fi
* WAN
* 10G
* SFP+
Power:
* 19.5V via DC jack
Installation instructions:
--------------------------
1. Flash temporary OpenWrt initramfs:
* Flash openwrt-qualcommax-ipq807x-asus_rt-ax89x-initramfs-factory.trx
via the stock firmware.
Administration -> Firmware Upgrade -> Manual Firmware update (Upload)
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
2. Sysupgrade from OpenWrt initramfs:
* Copy openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin to
/tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin of
the running initramfs image.
* Simply sysupgrade -n /tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
PMD Global Transmit Disable bit should be cleared for normal operation.
This should be HW default, however I found that on Asus RT-AX89X that uses
AQR113C PHY and firmware 5.4 this bit is set by default.
With this bit set the AQR cannot achieve a link with its link-partner and
it took me multiple hours of digging through the vendor GPL source to find
this out, so lets always clear this bit during .config_init() to avoid a
situation like this in the future.
aqr107_wait_processor_intensive_op() is moved up because datasheet notes
that any changes to this bit are processor intensive.
This is a modified version of patch that got merged upstream as AQR113C
has a separate config_init() upstream.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X has an external QCA8337 switch that has built-in
internal ethernet PHY-s that are supported by the QCA83XX PHY driver so
lets enable it.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X has an Qualcomm QCA8337 switch used to provide additional
1G copper ports, so lets enable qca8k in order to utilize DSA instead of
relying on SSDK for it.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X is using GPIO bitbanged MDIO on newer HW revisions, so lets
enable it in kernel config.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that newer SSDK is now expecting the switch node to be a subnode
of "ess-instance" node which also contains "num_devices" as the number of
switches as you can also have external switches connected.
Asus RT-AX89X is even more peculiar as its bootloader has a hardcoded path
to enable if on that revision there is an AQR113 connected to port 6 of the
switch.
So, lets move the current switch node under ess-instance as otherwise it
seems that SSDK is having some issues parsing the UNIPHY mode properly as
I am getting the following:
[ 6.981404] _adpt_hppe_instance1_mode_get[3275]:ERROR:port 6 doesn't support port_interface_mode 9
Which should not happen as that port has the mode set to 13.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Exclude additional initramfs image for Netgear RAX120v2 when no
initramfs image are compiled to fix build error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Trying to compile x86 or x86_64 on macOS will fail with:
openwrt/build_dir/target-x86_64_musl/linux-x86_64/linux-6.6.36/tools/include/linux/rbtree.h:21:10: fatal error: 'linux/stddef.h' file not found
After some digging, it seems that we dropped the old 212-tools_portability
patch when 6.6 x86 support was added, then Felix added back some parts of
it in ("kernel: fix tools build breakage on macos with x86") but trying to
build x86 kernels will still fail.
So, lets add more of the required changes from the 212-tools_portability
patch so that x86 kernels build on macOS.
Fixes: 69b145188f ("generic: 6.6: Removal of tools_portability.patch already included in kernel 6.6")
Link: https://github.com/openwrt/openwrt/pull/15904
Signed-off-by: Robert Marko <robimarko@gmail.com>
When building the kernel with -Wmaybe-uninitialized, GCC reports this
warning:
block/partitions/fit.c: In function 'parse_fit_partitions':
block/partitions/fit.c:164:3: warning: 'images' may be used uninitialized in this function [-Wmaybe-uninitialized]
164 | printk(KERN_ERR "FIT: Cannot find %s node: %d\n", FIT_CONFS_PATH, images);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
It appears to be a copy paste error. It's the "config" variable that is
supposed to be printed.
Fixes: e6aac8d98f ("image: add support for building FIT image with filesystem")
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
fit size should be rounded up instead of rounding down first and adding
a block. Otherwise the calculated size is one block more than needed
when fit size is exactly multiples of one block size.
Fixes: 9a863f803e ("kernel: mtdsplit: add support for FIT image")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Since 6.6 is now default, drop 6.1 support.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Let's switch the lantiq target to use kernel 6.6 by default.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports the fix for the broken "nosmp" and "maxcpus=0" cmdline
params.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since 6.1 is now default, drop 5.15 support.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patch implementing operations to get and set flow-control link
parameters of mtk_eth_soc via ethtool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.36..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
WiFi calibration data is already obtained via in-kernel NVMEM framework.
There is no need to also do so in userspace.
Fixes: dd58ad968a ("mediatek/filogic: add OpenWrt One support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The new numberspace base starts from 512 instead of 0. The number
base seems come from the kernel symbol CONFIG_GPIOLIB_FASTPATH_LIMIT.
Suppress warning:
gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The numberspace base has been changed since 6.6 kernel:
chip_num chip0 chip1 chip2 (32 gpios per bank)
old base 480 448 416
new base 512 544 576
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This commit adds support for TP-LINK RE6000XD.
The device is quite similar to the Mercusys MR90X V1,
except only 3 LAN ports and more LEDs.
So thanks to csharper2005 for doing all the groundwork.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (LAN3 2.5Gbps), 2xGbE (LAN 1Gbps, LAN1,
LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x signal
blue/red, 3 LAN blue gpio-controlled
Button: 2 (Reset, WPS)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, ubi0
partition contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART), unpopulated
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
Disassemble: rm the 2 screws at the bottom and the one at the backside.
un-clip the case starting at the edge above the LEDs.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot openwrt-mediatek-filogic-tplink_re6000xd-initramfs-kernel.bin bootm
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Notice: while I was successfull at activating ssh (as described
here:
https://www.lisenet.com/2023/gaining-ssh-access-to-tp-link-re200-wi-fi-range-extender/)
Unfortunately I haven't found the correct root password.
Looks like they are using a static password
(md5crypt, salt + 21 characters) that is not the web
interface admin password.
The TP-LINK RE900XD looks like the very same device,
according to the pictures and the firmware.
But I haven't checked if the OpenWrt firmware works as well
on that device.
The second ubi partition (ubi1) is empty and there is no known
dual-partition mechanism, neither in u-boot nor in the stock firmware.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Drop configs, files and patches for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15635
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15635
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove patches related to some ancient cache aliasing bugs that were fixed in earlier versions and are no longer relevant to us.
Co-authored-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15635
Signed-off-by: Robert Marko <robimarko@gmail.com>
Silence ath79 GPIO driver warning by setting GPIO numberspace base
dynamically. This patch also reorganize and fix the GPIO numbers on
6.6 kernel. The new gpio chip base number algorithm:
gpiochip ath79-SOC ath9k-0 ath9k-1
base 512 512+ngpios 512+ngpios+10
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15784
Signed-off-by: Robert Marko <robimarko@gmail.com>
Each ath9k device only has 10 gpios. ath9k-0 gpio number range is
502-511, and ath9k-1 gpio number range is 492-501. So "5GHz External
Antenna A" gpio line number should be 492 instead of 489.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15784
Signed-off-by: Robert Marko <robimarko@gmail.com>
use u-boot-rockchip.bin to copy SPL/TPL/U-Boot to the image.
since binman was used in mainline u-boot for rockchip, we can use
u-boot-rockchip.bin instead of idbloader.img and u-boot.itb.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15815
Signed-off-by: Robert Marko <robimarko@gmail.com>
BDFs come from latest firmware, version 1.1.19.209880 (2022-06-20):
- /lib/firmware/IPQ4019/v1/FCC/boardData_1_0_IPQ4019_DK04_2G.bin
- /lib/firmware/IPQ4019/v1/FCC/boardData_1_0_IPQ4019_DK04_5G.bin
- /lib/firmware/QCA9888/v1/FCC/boardData_2_0_QCA9888_5G_Y9690_SBS_HB.bin
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15844
Signed-off-by: Robert Marko <robimarko@gmail.com>
As reported in https://github.com/openwrt/openwrt/issues/15834 using the PWR
LED for indicating diag status is confusing since this is usually used for
power supply failures on RPi devices.
This commit uses ACT LED for diag status and restores it to mmc activity.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These removed compatible strings do not exist in the source code
nor the dt-binding documents. They are useless.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some devices with MediaTek SoCs don't use the first but only the second
MAC in the chip. Especially with MT7981 which got a built-in 1GE PHY
connected to the second MAC this is quite common.
Make sure to reset and enable PSE also in those cases by skipping gaps
using 'continue' instead of aborting the loop using 'break'.
Fixes: 75081235b8 ("generic: 6.6: (re-)add support multiple PPE to mtk_eth_soc")
Reported-by: Daniel Suchy <danny@danysek.cz>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Switch to netif_napi_add_weight and add back weight value from <= v5.15.
Fixes: 8f6033e287 ("bmips: enet: add compatibility with kernel 6.1")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The bootloader provides the partition table using the boot arguments
and uses the name spi-nor and spi-nand for the different controllers.
The old code was not setting the name any more because mtd->name was
already set before. Move the setting of the name to the spi-mem code
now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These targets are interesting for automated testing. The currently
available targets are from 2017 and either we should enable them again
or delete the remaining files on the download servers.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/15740
Link: https://github.com/openwrt/openwrt/pull/15740
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently, only the WAN MAC is being populated on Habanero DVK, and that is
happening via the ethernet1 alias so U-Boot does it, previously ethernet0
was implicitly added in the SoC DTSI so it would populate the LAN MAC-s but
it was dropped(rightly so) so now LAN MAC-s and the GMAC one are random.
So, lets simply switch to using NVMEM to assign the proper MAC adresses.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Notify via dev_info when a random MAC address is set.
of_get_ethdev_address can return -EPROBE_DEFER for NVMEM devices,
return this up, so that ipqess can defer as well.
Also move this MAC assignment from _init into _probe, so that this defer
can happen earlier.
Before change, with MAC address allocated from a built-in NVMEM layout
driver (mikrotik,routerboot-nvmem) with extra of_get_ethdev_address
result and random MAC printfs:
[ 1.197571] ipqess-edma c080000.ethernet: ipqess_init of_get_ethdev_address ret:-517, of_node: /soc/ethernet@c080000
[ 1.197690] ipqess-edma c080000.ethernet: generated random MAC address 22:e7:36:e0:e4:a3
[ 1.614444] ipqess-edma c080000.ethernet eth0: entered promiscuous mode
[ 5.055929] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
after change:
[ 1.173776] ipqess-edma c080000.ethernet: of_get_ethdev_address: -517
[ 1.614607] ipqess-edma c080000.ethernet eth0: entered promiscuous mode
[ 5.246105] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
[ 5.260754] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
with extra __func__ printf to show _probe and _init:
[ 1.173685] ipqess-edma c080000.ethernet: ipqess_axi_probe
[ 1.173784] ipqess-edma c080000.ethernet: of_get_ethdev_address: -517
[ 1.280347] ipqess-edma c080000.ethernet: ipqess_axi_probe
[ 1.304844] ipqess-edma c080000.ethernet: ipqess_init
[ 1.614664] ipqess-edma c080000.ethernet eth0: entered promiscuous mode
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Link: https://github.com/openwrt/openwrt/pull/15831
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that the issue with WED has been sorted out, re-add support for
multiple PPE to the mtk_eth_soc driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
"linux,ubi" compatible MTD device can be automatically attached early
since commit fc153aa8d9. Therefore, there is no need to attach MTD
devices named "ubi" or "data" again.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Used by ethernet interfaces on AP3935i.
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Link: https://github.com/openwrt/openwrt/pull/13629
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix issue with LAN1 interface on ap3935 devices, where the LAN
1interface won't come up after boot unless the bootloader has
initialized the network stack. Use of `fixed-link` in the prior code
kept the driver from clobbering PHY settings, but now that the driver
supports rgmii-id phy-mode, we can just use that.
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Link: https://github.com/openwrt/openwrt/pull/13629
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Updates ap3935 target to use the mdio controller built-in to gmac0,
rather than having the SoC bit-bang mdio from gpio pins
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Link: https://github.com/openwrt/openwrt/pull/13629
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Specifications:
* SoC: BCM63168
* RAM: NT5CC64M16GP-DI, DDR3 128MiB
* NAND: W29N01HVSINA, 128MiB
* Ethernet: 4x1000M LAN, 1x 1000M WAN
* Serial interface: on board but not populated, 3.3V, 115200, 8N1
Notes:
* Use DSA for VLAN and switches
* Ethernet ports and USB works
* gpio-leds are not working
* WLAN, xDSL, and FXS are not going to work
Signed-off-by: Hang Zhou <929513338@qq.com>
[refactor, reorder, drop unneeded or not working stuff]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Turns out the device got two buttons, while the currently listed on is
actually WPS, and the other (will hidden) button is intended as RESET.
Update DT accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove unneeded default-state from led_power_green (led@8) to be in line with
other bmips devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Remove unneeded default-state from led_power_green (led@4) to be in line with
other bmips devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Replace Aquantia pending LEDs patch with upstream version.
Sadly net maintainers didn't like integrated solution hence we still
need to handle LED restore on reset with custom solution.
Link: https://github.com/openwrt/openwrt/pull/15797
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix RAX120v2 PWM Fan controller wrong definition by using a non-existant
kmod and using the wrong compatible for it enabling an external clock
while actually the device use an internal one.
Link: https://github.com/openwrt/openwrt/pull/15796
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch for G761 PWM Fan controller support. This is used by
an ipq807x RAX120v2 and have an internal clock that was currently
unconfigured making the device not working.
Link: https://github.com/openwrt/openwrt/pull/15796
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix broken line break for Linksys e8350-v1 pushed with CRLF instead of
LF.
Fixes: 45b3c620e5 ("ipq806x: add support for Linksys e8350-v1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AC2400 Dual-Band Gigabit Wi-Fi Router base on ipq8064.
https://www.linksys.com/support-product?sku=E8350
Specification:
- Qualcomm dual-core IPQ8064 @ 1.4 GHz
- 512 MB of RAM
- 4 MB of SPI NOR MX25U3235F
- 128 MB of NAND S34MS01G2
- Qualcomm QCA9880 2.4GHz 802.11bgn
- Quantenna QSR1000 5GHz 802.11ac (no support)
- 4 x 10/100/1000 Mbit/s w/ vlan support Ethernet
- Qualcomm Atheros QCA8337 switch
- 1 x 3.0 + 1 x 2.0 (combo with eSata port)
- 115200, 8N1 internal serial console
- Power, Reset, WPS and WLAN buttons
- Power, WPS and WLAN leds
- 12 VDC, 3 A power
Installation:
The installation must be done using web interface of the router.
To achive this new firmware-utils tool was added to set correct
magic headers for the factory images.
Installation from vendor firmware:
1. Flash over the native Linksys WEB interface using factory image.
Installation using recovery mode:
1. Power off the device and disconnect the WAN port.
(Only LAN port to be connected)
2. Press & hold the "Reset" button
3. Power on the device & wait 10 seconds with pressed "Reset" button
4. Set IP Internet Protocol on your PC from
192.168.1.0/24 network (Router is on IP 192.168.1.1)
5. Open the Firmware Recovery page in your browser:
http://192.168.1.1/index.shtml
Firmware Recovery -> File Name -> Recovery & Reboot
The device page in inbox:
https://openwrt.org/inbox/toh/linksys/linksys_ea8350_1
Signed-off-by: Sergey Filippov <sergey.filippov@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/15798
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream fix for incorrect ifdeffery and dependency of CONFIG_KEXEC,
which causes compilation errors with the following symbols:
CONFIG_CRASH_CORE=y
CONFIG_KEXEC_CORE=y
CONFIG_CRASH_DUMP=y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch adds support for Mikrotik RB5009UG+S+IN.
Specifications:
- SoC: Marvell Armada 7040 (88F7040) - 4 cores, ARMv8 Cortex-A72, 1.4GHz, 64bit
- RAM: 1024MB DDR4
- Flash: 16MB SPI NOR flash, 1024MB NAND
- Ethernet:
* Marvell 88E6393X - Amethyst:
* one 2.5G RJ45 port via Qualcomm QCA8081 PHY
* seven 1G RJ45 ports via built-in PHY-s
* one 10G SFP+ cage
* All ports share the same 10G switch uplink to the CPU
- LED: User, SFP, Hdr1, Hdr2
- Buttons: Reset
- UART: 115200 8n1 on the MikroTik 16 pin header
- USB: One USB3 port
- Power: 24-57 V via
* DC jack
* 802.3af/at PoE on Ethernet 1
* 2-pin terminal on the side
16 Pin header pinout:
1 GND Vcc RX ? GND
#--------------------#
|.-. .-. .-. .-. .-. |
|'-' '-' '-' '-' '-' |
|.-. .-. .-. .-. .-. |
|'-' '-' '-' '-' '-' |
#--------------------#
2 CLK DO /CS TX DI
Do note that the default RouterBoot has disabled UART even when the
required hard-config bit is set to indicate UART support.
Patched RouterBoot must be used if UART is desired.
Also, since ARM64 Linux support does not support in any way appending the
DTB to the kernel image we use mainline U-Boot with added RB5009 support
in order to boot OpenWrt.
MikroTik uses YAFFS to store the boot kernel and we use YAFUT to put U-Boot
as the kernel which RouterBoot then simply boots as an ELF.
Install instructions:
NOTE: In case you are using an existing out of tree version of OpenWrt make
sure to reinstall RouterOS via Netinstall to return the expected partition
layout.
1. Prepare FAT or EXT4 formatted USB drive with OpenWrt initramfs:
* Copy bin/targets/mvebu/cortexa72/openwrt-mvebu-cortexa72-mikrotik_rb5009-initramfs-uImage.itb
to the root of FAT or EXT4 formatted USB drive.
* Plug in the drive to the RB5009 USB port
2. Boot the modified OpenWrt built U-Boot ELF:
u-boot.elf from bin/targets/mvebu/cortexa72/u-boot-rb5009/u-boot.elf
Consult OpenWrt wiki for common instructions on switching to boot from
Ethernet once as well as serving the file:
https://openwrt.org/toh/mikrotik/common
Once U-Boot is booted it will attempt to boot in the following order:
1. NAND
2. USB
3. Network
NAND is expected to fail but USB or Networking need to serve the OpenWrt
initramfs image and after booting it will be accessible from LAN ports
on the default 192.168.1.1 IP with default credentials.
3. Flash modified RouterBoot that enables UART (Optional but recommended):
https://public.robimarko.eu/RB5009/70x0-7.15-uart.fwf
* Copy the file over to the booted OpenWrt initramfs to /tmp
* Run: mtd erase RouterBOOT-primary
* Run: mtd write /tmp/70x0-7.15-uart.fwf RouterBOOT-primary
4. Install U-Boot to boot OpenWrt:
* Copy the u-boot.elf from bin/targets/mvebu/cortexa72/u-boot-rb5009/u-boot.elf
to OpenWrt initramfs to /tmp.
* Run: . /lib/functions.sh
* Run: yafut -d /dev/mtd$(find_mtd_index "YAFFS") -w -i /tmp/u-boot.elf -o kernel -T
This will use yafut to copy the U-Boot as kernel in YAFFS so that RouterBoot boots it.
5. Wipe the NAND UBI partition:
* Run: ubiformat /dev/mtd$(find_mtd_index "ubi") -y
This will prepare the existing RouterOS rootfs partition for OpenWrt.
6. Flash OpenWrt:
* Copy the bin/targets/mvebu/cortexa72/openwrt-mvebu-cortexa72-mikrotik_rb5009-squashfs-sysupgrade.bin
to OpenWrt initramfs to /tmp.
* Run: sysupgrade /tmp/openwrt-mvebu-cortexa72-mikrotik_rb5009-squashfs-sysupgrade.bin
Device will reboot, boot U-Boot and then OpenWrt.
Recovery:
In case you need to reinstall OpenWrt if it crashes after U-Boot, there is
a recovery mechanism in OpenWrt to boot the OpenWrt initramfs.
You need to hold the reset button while U-Boot is booting and then it will
boot the OpenWrt initramfs from:
1. USB
2. Networking
In recovery mode U-Boot will light all of the LED-s except for the switch
ones.
In case you want to return to RouterOS, you can simply do that via
Netinstall like on any other MikroTik board.
Credits also go to Serhii Serhieiev <adron@mstnt.com> who origininally
figured out the RouterBoot modification for UART, the missing 10G MVPP2
support in U-Boot as well as the custom aux loader to boot directly via
RouterBoot.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
In order to not have to ship envtools configuration per board, we can
instead rely on the kernel U-Boot environment NVMEM driver through which
envtools can read/write the environement.
Since size difference is negligeble and this subtarget has rather large
storage regardless, enable it by default.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
MikroTik RB5009 will be using advantage of the MikroTik platform drivers,
RouterBoot partition parser and SPI NOR variable erase support.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
Marvell 70x0 and 80x0 both have ARM SBSA Generic Watchdog built-in,
so lets enable the required driver for them.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
MikroTik RB5009 uses Qualcomm QCA8081 PHY for the 2.5G RJ45 port,
so we need to enable the driver for it.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
QCA808x does not currently fill in the possible_interfaces.
This leads to Phylink not being aware that it supports 2500Base-X as well
so in cases where it is connected to a DSA switch like MV88E6393 it will
limit that port to phy-mode set in the DTS.
That means that if SGMII is used you are limited to 1G only while if
2500Base-X was set you are limited to 2.5G only.
Populating the possible_interfaces fixes this, so lets backport the patches
from kernel 6.9.
This also includes a backport of the Phylink PHY validation series from
kernel 6.8 that allows the use of possible_interfaces.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
Marvell Amethyst switches use a different SMI GPIO pin setup than other
switches, and since RB5009 uses Amethyst switch and its SMI bus to talk
to QCA8081 lets backport the required fix from kernel 6.9.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that SSDK has been updated to use in-kernel SMEM ID-s to identify
the SoC its running on instead of relying on the downstream socinfo.h
header we can move the read_ipq_soc_version_major() function directly to
cpr3-util.c as its the only user of anything from the header and drop it.
Link: https://github.com/openwrt/openwrt/pull/15786
Signed-off-by: Robert Marko <robimarko@gmail.com>
This hack is used to make sure that the mfd device starts before the
mtd driver[1]. Now the linux driver framework "struct spi_driver {}"
can always ensure this.
[1] 47f8fd1dde ("ar71xx: rewrite SPI drivers for the RB4xx boards")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
After porting the ar71xx target to the new ath79 target, we are now
using the device tree instead of the device mach file. And the
platform drivers already support deferred probe. So there is no need
to keep it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
There are some new commits, so refresh and update patches.
Some build warnings have been fixed upstream too.
Add backport target/linux/generic/backport-6.6/722-v6.10-dt-bindings-arm-qcom-ids-Add-SoC-ID-for-IPQ5321.patch.
Removed upstream:
[-] qca-ssdk/patches/101-hsl_phy-add-support-for-detection-PSGMII-PHY-mode.patch
[-] qca-ssdk/patches/201-fix-compile-warnings.patch
List of changes:
2024-04-16 -c451136b- qca-ssdk: strip MRPPE code
2024-06-05 -f455a820- [qca-ssdk]: fix enum-int-mismatch warnings
2024-05-31 -bbfc0fa9- Merge "[qca-ssdk]: update eee status of phydev"
2024-05-31 -adbe9dc5- Merge "[qca-ssdk]: support psgmii and uqsxgmii mode of kernel"
2024-05-31 -d06ca777- Merge "[qca-ssdk]: fix 5G issue with the AQR FW that use 5gbaser for 5G speed"
2024-05-31 -c6f539a5- Merge "qca-ssdk: support mrppe pktedit padding functions"
2024-04-29 -c321e2a9- qca-ssdk: support mrppe pktedit padding functions
2024-05-24 -ee6e201e- qca-ssdk: Fix the big endian compile error
2024-05-15 -8c116bb9- [qca-ssdk]: update eee status of phydev
2024-05-20 -f0341a2c- Merge "qca-ssdk: Enable igmp for PPE MINI profile"
2024-05-16 -44a0ce93- qca-ssdk: Enable igmp for PPE MINI profile
2024-05-15 -8b91bbf6- [qca-ssdk]: support psgmii and uqsxgmii mode of kernel
2024-05-14 -7eec1658- [qca-ssdk]: fix 5G issue with the AQR FW that use 5gbaser for 5G speed
2024-05-12 -b9f5ea0e- [qca-ssdk]: ethtool support, do not change wake-up timer when the requested timer is 0
2024-05-09 -5e2c15ed- Merge "[qca-ssdk]: remove check when mht clock enable"
2024-05-09 -a1563b90- Merge "[qca-ssdk] support new sku IPQ5321"
2024-04-23 -f04b7680- [qca-ssdk]: show unknown status when link down
2024-03-22 -33b91b30- [qca-ssdk]: remove check when mht clock enable
2024-04-29 -b6362f2b- Merge "qca-ssdk:fix bug in marina nptv6 iid cal"
2024-04-29 -097033ae- Merge "[qca-ssdk] support cypress uniphy0 connecting MHT switch port0"
2024-04-24 -d45560fd- qca-ssdk:fix bug in marina nptv6 iid cal
2024-04-24 -7d7a42af- qca-ssdk: enable policer counter on low memory profile
2024-04-18 -e36cf6ea- Merge "[qca-ssdk]: change portvlan egress mode initial value as untouched"
2024-04-18 -27817881- Merge "[qca-ssdk]: update the aqr phy supported ability"
2024-04-18 -5a3a693c- Merge "qca-ssdk:support marina nptv6"
2024-04-16 -129fe9b3- Merge "qca-ssdk: support tunnel fields and innner fields inverse"
2024-01-09 -fc8f6abd- qca-ssdk:support marina nptv6
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15771
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds two more common PHY brands to the image.
Realtek is used on the Google Coral "Phanbell" board (i.MX8MQ).
SMSC has been used on various Raspberry Pi boards.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Support for 'fsl,imx8mq-usb-phy' is needed for USB to work
on NXP i.MX8MQ and i.MX8MP platforms.
Tested with a Google Coral "Phanbell" board.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This was discovered when trying to run OpenWrt on Hetzner Cloud's
Arm-based instances.
Hetzner uses QEMU/KVM with virtio-gpu as the main display device,
together with an ACPI firmware. This was not displaying a console
previously.
This setup can be emulated by qemu using options below:
qemu-system-aarch64 \
-machine virt \
-bios QEMU_EFI.fd \
-device virtio-gpu \
-usb \
-device qemu-xhci,id=xhci \
-device usb-tablet,bus=xhci.0 \
-device usb-kbd,bus=xhci.0 \
-vnc :0
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This PMU (performance management unit) related kernel option
can appear under certain kernel configurations (such as
KVM being enabled).
Disable them, as we do with other PMU-related options.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Running the glibc-static check with GCC14 as the host compiler will fail:
Please install a static glibc package. (Missing libutil.a, librt.a or libpthread.a)
However, this error will get printed even with the required static
libraries installed when GCC14 is used.
Manually running the check exposes the real error:
<stdin>: In function ‘main’:
<stdin>:1:45: error: implicit declaration of function ‘timer_gettime’ [-Wimplicit-function-declaration]
GCC14 now errors on implicit declarations by default, so lets add the
required time.h header to fix compilation and thus the check.
Link: https://github.com/openwrt/openwrt/pull/15778
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a set of upstream patches for the imx8m{m,n,p} based Venice
boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/15736
Signed-off-by: Robert Marko <robimarko@gmail.com>
The GW74xx's first RJ45 is eth0 which should be the WAN adapter, not
eth1 which is the CPU uplink port to the switch.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/15736
Signed-off-by: Robert Marko <robimarko@gmail.com>
qoriq has had kernel 6.1 as testing for 2 months now, so lets default to
it and drop 5.15 support.
Link: https://github.com/openwrt/openwrt/pull/15767
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, information from MikroTik hard_config is only available via
sysfs, meaning that we have to rely on userspace to for example setup MACs.
So, lets provide a basic NVMEM layout based driver to expose the same cells
as sysfs driver exposes.
Do note that the we dont extract the WLAN caldata and BDF-s at this point.
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/15665
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move the hard config tag ID-s to a separate header so they can be reused
by the NVMEM driver as well.
Link: https://github.com/openwrt/openwrt/pull/15665
Signed-off-by: Robert Marko <robimarko@gmail.com>
This driver has already been packed as a software package. There is
no need to build it into the kernel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch was causing buildbot issues when copying arm64 DT files since
bcm283x-rpi-csi1-2lane.dtsi and bcm283x-rpi-lan7515.dtsi were linked to
"../../../../arm/boot/dts/" instead of "../../../../arm/boot/dts/broadcom".
These files aren't needed, so let's remove them instead of fixing them.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15762
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently, of_get_ethdev_address() return is checked for any return error
code which means that trying to get the MAC from NVMEM cells that is backed
by MTD will fail if it was not probed before ag71xx.
So, lets check the return error code for EPROBE_DEFER and defer the ag71xx
probe in that case until the underlying NVMEM device is live.
Link: https://github.com/openwrt/openwrt/pull/15752
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since the introduction of out-of-band tagging, writing the outbound tag
had been completely broken: First, in place of a port mask containing
the port number, just the port number itself was set in the register
value. Just after that, the full port mask 0x3e (all 5 external ports)
was set unconditionally.
This remained unnoticed because the switch would then use the FDB to
decide where to send unicast packets; broadcast and multicast packets
were however sent to every port.
Fix the port tag computation and only use the full port mask as a
fallback for non-DSA mode, as it was done in the older driver patches
used on Linux 5.15.
Fixes: cd9c721124 ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Robert Marko <robimarko@gmail.com>
In my previous attempt to solve the PCI problems for the lantiq targets,
I did not pay attention to the fact that the original accesses to the
GPIO took place in RAW mode. As a result, the polarity defined in the
device trees (apart from the initial value) was irrelevant.
In addition, the expected name of the GPIO in the dts has changed due to
the upstream change and therefore no RESET is currently performed.
As discussed in [1] on the linux-mips mailing list, we will now adapt
the dts files accordingly instead of patching the driver:
- dts property will be renamed to "reset-gpios"
- Polarity is set to "GPIO_ACTIVE_LOW".
I have verified this with a TP-Link TD-W8980. The PCI device is now
recognized by the system.
[1] https://patchwork.kernel.org/project/linux-mips/patch/20240607090400.1816612-1-ms@dev.tdt.de/
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # Tested on AVM 7330 (ar9)
Link: https://github.com/openwrt/openwrt/pull/15731
Signed-off-by: Robert Marko <robimarko@gmail.com>
At some point RPi LEDs were renamed from led0/led1 to PWR/ACT.
This patch fixes this and also automatically detects the status_led without
relying on board_name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Currently, trying to upgrade on a MikroTik NAND device will force you to
use sysupgrade -n due to:
upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n).
upgrade: NAND images switched to yafut. If running older image, reinstall from initramfs.
So instead of having users manually set the new compat version lets do
what other targets do and set it for all NAND devices after good boot.
Link: https://github.com/openwrt/openwrt/pull/15754
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devices were already supported. I merely added missing entries to:
1. make them easier to locate in firmware selector
2. allow firmware upgrades to proceed without dire warnings
Sample dire warning contains:
upgrade: Device raspberrypi,model-zero-2-w not supported by this image
upgrade: Supported devices: rpi-3-b rpi-3-b-plus rpi-zero-2 \
raspberrypi,2-model-b-rev2 raspberrypi,3-model-b \
raspberrypi,3-model-b-plus raspberrypi,3-compute-module \
raspberrypi,compute-module-3 raspberrypi,model-zero-2
With this patch, the firmware upgrade proceeds normally.
Signed-off-by: Dave Brand <dbrand666@users.noreply.github.com>
Convert line endings from DOS to Unix using dos2unix.
Fixes: 2da2705a44 ("ramips: add support for WINSTARS WS-WN536P3")
Fixes: 5560791bbd ("ramips: add support for OpenFi 5Pro Travel Router")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol was removed upstream, but it was present on bcm27xx due to a
malformed upstream RPi patch.
Fixes: 8c405cdccc ("bcm27xx: add 6.6 kernel patches")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.34..rpi-6.1.y
Some patches needed rebasing and, as usual, the applied and reverted, wireless
drivers, Github workflows, READMEs and defconfigs patches were removed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is preparation for 6.6 kernel support. Copying files makes it easier to
track their git history.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Replace Silicon Labs patch with upstream version as they got merged in
kernel 6.3.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[ rework commit title and description, use better patch ]
Link: https://github.com/openwrt/openwrt/pull/15300
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Now that we can pass the desired compression via cmdline, pass ZSTD as the
desired compression algorithm for F2FS.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
F2FS requires the compression algorith to be passed as argument while
mounting, so lets do so for the misc partition.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In order to prolong the eMMC life and utilize ZSTD compression on Methode
devices, we must format the F2FS rootfs and misc partition with xattr and
compression support feature flags first.
This will only happen if partitions are broken currently, but later
commits will add support to convert existing boards to use compression.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Methode devices require mkfs.f2fs in order to format rootfs and misc
partitions if they have not already been formatted.
fdisk is required if partition table got broke so it can be regenerated.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
We would love to utilize ZSTD compression support in F2FS on the
Methode euroDPU so lets enable the required kernel support.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Refresh patches as line numbers changed with newer upstream version
since original backport PR was opened.
Fixes: a5c095c453 ("generic: 6.6: replace (broken) downstream patch with upstream solution")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Our downstream patch "net/core: add optional threading for backlog processing"
has been broken with the switch to Linux 6.6.
Replace it by backporting the now available upstream solution.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15592
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop config+patches for kernel 6.1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15713
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch the uml target to kernel 6.6.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15713
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
UML didn't have a subtarget defined.
While this compiled fine, the patch caused funny filenames
for the generated files to appear:
- "openwrt-uml--vmlinux"
- "openwrt-uml--squashfs.img"
- "openwrt-uml--ext4.img"
- ...
since "generic" is implied anyway, let's just set it.
Fixes: d997477775 ("treewide: remove implicit SUBTARGET")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15713
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop config+patches for kernel 6.1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15721
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch the apm821xx targets to kernel 6.6.
no complains received.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15721
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
gpio is deprecated. Found with dtc's -Wdeprecated_gpio_property
Used git grep -E $'\tgpio = <' to make the changes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15681
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions for SXK80
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/15732
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move nvmem-cells definitions to dts files for compatibility with other files
in which mt7628an_tplink_8m.dtsi is loaded, to prevent overwriting
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Partially revert commit 98ddfbc56a ("generic: 6.6: backport upstream
commits for mtk_eth_soc") as the commit breaks WED. A better solution to
assign PPE units in case of WED has still to be found.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow a wider audience to test this pending series.
Use about to be submitted v3 which factors out block notification support.
Apart from dropping the no longer needed (and problematic) fallback for
for the 'partitions' node being present at the device parent there are
no intended functional changes.
As opening a block device as file is not supported yet in Kernel v6.6,
use the previous method as backporting seems a bit too involving.
Fixes: #15642
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The WS-AP3710i does not correctly expose its label-mac on eth0 anymore
since the change to simpleLoader.
Fix this by obtaining the label-mac from the U-Boot environment.
Signed-off-by: David Bauer <mail@david-bauer.net>
With the introduction of the simpleImage loader, the MAC address is not
set by the bootloader anymore.
Fix this by reading the MAC address from the U-Boot environment
partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
We haven't received any bug reports in the past few weeks. So it's
time to set kernel 6.6 as the default and remove kernel 6.1 support.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The broadcom-wl driver was removed from OpenWrt, remove also the
profiles using it.
Fixes: e772b75d5d ("broadcom-wl: remove package")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The braodcom-wl driver was removed from OpenWrt, remove the special
exports it needed.
Fixes: e772b75d5d ("broadcom-wl: remove package")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file is executable:
target/linux/ramips/dts/mt7621_dlink_dir-2150-a1.dts
Has to be fixed.
Fixes: 30e8fd73ec ("ramips: Add support for D-Link DIR-2150-A1")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
This commit fixes random lan mac for sercomm dxx devices.
Fixes: 3395184825 ("ramips: mt7621: nix mac-address-increment")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
0db4f9785c changed the variable name from
athaddr to ethaddr. Restore.
Fixes: 0db4f9785c ("ath79: convert ath10k calibration data to NVMEM (ASCII MAC)")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This router has two rootfs partitions and dualboot is used.
Vendor firmware may swap the rootfs partition location, u-boot append
'ubi.mtd=rootfs' in the end of cmdline. Since we use fixed-partitions,
force boot from the first rootfs partition to avoid boot failure.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15700
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport an upstream Linux fix to prevent BPF kfunc functions from being
removed during linker optimization when building BTF-enabled vmlinux.
The telltale sign of this occurring is build log warnings (e.g. mips64el):
BTFIDS vmlinux
WARN: resolve_btfids: unresolved symbol bpf_verify_pkcs7_signature
WARN: resolve_btfids: unresolved symbol bpf_lookup_user_key
WARN: resolve_btfids: unresolved symbol bpf_lookup_system_key
WARN: resolve_btfids: unresolved symbol bpf_key_put
WARN: resolve_btfids: unresolved symbol bpf_iter_task_next
WARN: resolve_btfids: unresolved symbol bpf_iter_css_task_new
WARN: resolve_btfids: unresolved symbol bpf_get_file_xattr
WARN: resolve_btfids: unresolved symbol bpf_ct_insert_entry
NM System.map
SORTTAB vmlinux
Link: https://lore.kernel.org/bpf/ZlkoM6%2FPSxVcGM6X@kodidev-ubuntu/
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15697
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The wifi radios on wax620 and wax630 got a random mac
address on boot. So fix this by using ath11k_patch_mac
and give a static mac address from label-mac-device.
Tested and working on wax620 and wax630.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15597
Signed-off-by: Robert Marko <robimarko@gmail.com>
octeontx is currently stuck on kernel 5.15 since using 6.1 breaks booting,
and unfortunately nobody has stepped up to fix this issue.
Gateworks who were primary users have supported the removal.
Link: https://github.com/openwrt/openwrt/pull/15686
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bump to kernel 6.6 increased the GPIO base from
412 to 512 on this target.
We need to compensate for that in the GPIO numbers being passed
to uci to fix following kernel report:
[ 24.176183] export_store: invalid GPIO 423
Tested on a Wallys DR40x9 board.
Please note that:
Boards "rtl30vw" and "wpj428" are not being altered here.
They define GPIO numbers which are even below the previous
base of 412 which looks wrong.
Actual testing on these boards should be conducted to validate
and optionally fix GPIO numbering.
Suggested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
The WLR-1240 (ZX-5434) is an AC1200 Wave 2 outdoor repeater
with omnidirectional antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.
Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- top RGB LED ring
TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot
HTTP installation:
- keep reset button pressed for 5 seconds during power on (light blue
LED flashes slowly, then quickly to confirm, then remains steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade
Opening the device
- use suction cup to remove top cap within LED ring
- two screws are located in holes underneath silicone sealant
- two further screws are located at the bottom
initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The WLR-1230 (ZX-5207) is an AC1200 Wave 2 outdoor repeater
with sector antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.
Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- 3 LEDs WLAN, LAN, RES; PWR LED is not software-controllable
TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot
HTTP installation:
- keep reset button pressed for 5 seconds during power on (LEDs
flash slowly, then quickly to confirm, then remain steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade
Opening the device
- two screws are located in the bottom left and right corners
underneath the label, inner tray slides out easily
initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Add the kmod-mt7915e wifi driver to the default packages for the Ruijie
RG-X60 Pro. kmod-mt7915e has to be added recently and was not done
before merging the support for Ruijie RG-X60 Pro.
Fixes: 3de3c2bdfa ("mediatek: add support for Ruijie RG-X60 Pro")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cudy assigns hardware versions to its devices on its website, and
the Cudy TR1200 router is now Cudy TR1200 v1.
OpenWrt currently uses both variants, and this commit removes
inconsistencies using only the new name.
Signed-off-by: Luis Mita <luis@luismita.com>
Switch to new nvmem binding.
Also fixes a issue that the MAC address assigned to lan/wan was reversed.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
- SOC: MediaTek MT7981
- ram: 256MB DDR3
- FLASH: 16MB SPI-NOR
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3 partition "factory" at 0x4 (binary), on label
5G: 80:3F:5D:xx:xx:x3 Same as 2G
Installation Method 1: ssh
--------------------------
1. Connect PC to the lan port. Set the PC IP to 192.168.10.100 if
required.
2. Navigate to http://192.168.10.1/
3. Log into the Wavlink WebGUI. Default username/password is
admin/admin.
4. Use WebGUI to upgrade the firmware to
WAVLINK_WN586X3-A_M86X3A_V240113_WO-GDBYFM-modified.bin
downloaded from
https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
Warning: All settings will be lost!
5. Wait about 5 minutes, and after flashing is completed, log into
the router using (with admin123 as password):
ssh root@192.168.10.1
6. scp the openwrt image file onto the router, usually under /tmp
somewhere.
openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin
7. Flash openwrt image file like so:
mtd write \
openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin \
firmware
Warning: Previous firmware will be overwritten!
8. Wait about 5 minutes, and after the flashing is completed, set
the PC IP to 192.168.1.100 if required and log into the router
like so:
ssh root@192.168.1.1
Installation Method 2: u-boot
-----------------------------
1. Connect UART: TX-> 586X3 RX, RX-> 586X3 TX, GND-> 586 GND.
2. Connect PC to the wan (not lan!) port.
3. Setup the tftp server on PC, set IP to 192.168.10.100,
4. Power on the device. Select '2' to upgrade firmware in Uboot.
5. Input the image name and start to upgrade.
Uboot console log:
CPU: MediaTek MT7981
Model: mt7981-rfb
DRAM: 256 MiB
Core: 34 devices, 13 uclasses, devicetree: embed
Loading Environment from nowhere... OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address -
02:47:fb:b2:53:2d
eth0: ethernet@15100000
UBOOT WN586X3A
gpio: pin 9 (gpio 9) value is 0
gpio: pin 10 (gpio 10) value is 0
gpio: pin 5 (gpio 5) value is 0
gpio: pin 12 (gpio 12) value is 0
gpio: pin 13 (gpio 13) value is 0
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
Co-authored-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: Sijia Huang <engineer31@win-star.com>
Before the nvmem rework, this was already handled in dts with
mtd-cal-data instead of qca,no-eeprom. No need to duplicate. Also, the
800 size value seems nonsensical. 440 is the standard.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Userspace handling is deprecated.
Also fix a bug with userspace handling where the wrong calibration data
was being used for the PCI card. The dts was correct but userspace was
not.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These symbols have already been removed from the upstream Linux source
code. They are automatically compared and removed by a kernel config
scanning script[1].
[1] https://github.com/openwrt/openwrt/pull/15324
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Make the OF-compatible zImage per-board selectable. This allows the
image to only be built with the wrapper if the target actually uses it.
This fixes build-failures for the mpc85xx-p2020 subtarget.
Fixes: 557c094f0579 ("mpc85xx: only build zImage on required targets")
Signed-off-by: David Bauer <mail@david-bauer.net>
Set the appropriate cpu_port value based on the use of realtek,extif0 to extif2
instead of the additional cpu_port parameter.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the appropriate cpu_port value based on the use of realtek,extif0 or realtek,extif1 parameter.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
All NETGEAR EX6150v2 validate the rootfs for which OpenWrt places a
fakeheader at the position, where the bootloader expects it.
Some EX6150v2 bootloaders do however make a broken assumption about
where the rootfs starts. This is due to them calculating the rootfs
start not based upon the kernel-length but the string-offset of the
FIT-image.
We have to be compatible with both this broken as well as the valid
calculation. So we do relocate the FDT string section to a
block-boundary and enlarge the FIT image to end at this boundary +
BLOCKSIZE / 2. This way, both the broken as well as correct calculations
do expect the rootfs-header at the same position.
It is worth noting, that this is a rare edge-case in which only happens
if the image-length as well as the start of the string-section are not
placed in the same erase-block. This is an edge-case which happens very
rarely (thus it was not spotted prior).
Affected:
- U-Boot 2012.07 (Jun 16 2016 - 11:59:37)
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 8f9546f7b0a14f3afa813e39ed45c968ece24464)
The recently added D-Link DNS-320L and the Zyxel NSA310S
is missing an RTC module so let's give them the default
Marvell RTC at least.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio is actually low active, fix it.
Fixes: 40e7fab9e4 ("mediatek: add Nokia EA0326GMP support")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15651
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IMX device-tree's for arm moved from arch/arm/boot/dts to
arch/arm/boot/dts/nxp/imx. Use that if using the 6.6 kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
copy 6.1 patches to 6.6 and fixup:
- removed patches already upstream
- adapted pathnames of dts patches for new kernel
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Patch 733-01-net-ethernet-mtk_eth_soc-use-napi_build_skb.patch needs
a refresh as line numbers no longer match.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For the first-time installation (mostly migrates from vendor firmware)
the ubiblock is not ready, but bootdev detection relies on it. This
means users must create ubiblock manually otherwise the sysupgrade
will not work.
Now a unique case is added for nand devices which use new fit format,
let's move to it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS/Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
These binaries are extraced from the factory firmware, which are
dynamically linked with aarch64 musl 1.1.24. To use them, you
must run them under the same runtime environment, otherwise the
binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
mv mkconfig seama /bin
chmod +x /bin/mkconfig
chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
Enter fakeroot if you are not login as root.
mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
tar -zcf backup.tar.gz etc/
mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.
A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz
Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Prior to performing a PROGRAM LOAD RANDOM DATA operation, a WRITE
ENABLE (06h) command must be issued to change the contents of the
memory array. Following a WRITE ENABLE (06) command, **first a PROGRAM
LOAD (02h or 32h) command must be issued to reset the cache**, then
issue a PROGRAM LOAD RANDOM DATA (84h or 34h) command
This is dirty fix provided to use by MediaTek engineer Sky Huang which
may resolve the "OpenWrt Kiss of Death" issue we've been seeing on the
Linksys E8450 aka. Belkin RT3200. However, it means that everything has
to be re-written with that patch already applied, ie. we need to rebuild
the installer once it is part of snapshot builds to have any effect.
Users already on FIP-in-UBI layout are advised to re-write 'fip' UBI
volume and 'bl2' MTD partition manually once from within Linux after
this fix has been applied.
A similar fix will also be required for U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buffalo WSR-2533DHPL2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MediaTek MT7621A.
Specification:
- SoC : MediaTek MT7621AT
- RAM : DDR3 128 MiB (Winbond W631GG6MB12J)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps x4
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB (J4)
- arrangement : 3.3V, GND, TX, RX from triangle-mark
- settings : 57600n8
- Power : 12VDC 1.5A
Flash instruction using factory.bin image:
1. boot WSR-2533DHPL2 normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
firmware update page
("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
button
Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL2
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL2 downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing
Notes:
- There are 2x factory*.bin images for different purposes.
- factory.bin : for flashing on OEM WebUI
- factory-uboot.bin: for flashing on OEM bootloader or initramfs image
factory-uboot.bin is useful for recoverying the device, or refreshing
when the kernel partition is expanded in the future. sysupgrade on
this device accepts factory-uboot.bin with option "-F", but on that
situation, user configurations won't be kept, so it's not for normal
use.
MAC addresses:
LAN : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
WAN : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
2.4 GHz: 18:EC:E7:xx:xx:E1 (Factory, 0x4 (hex))
5 GHz : 18:EC:E7:xx:xx:E4 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Buffalo WSR-2533DHPLS is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Very similar to Buffalo WSR-2533DHPL, but with NAND, different GPIO
and TRX partitions.
Specification:
- SoC : MediaTek MT7621AT
- RAM : DDR3 256 MiB (Samsung K4B2G1646F-BYMA)
- Flash : RAW-NAND 128 MiB
(Winbond W29N01HV or KIOXIA TC58BVG0S3HTAI0)
- WLAN : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC) 4 ports
- LED/keys : 8x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB (J4)
- arrangement : 3.3V, GND, TX, RX from triangle-mark
- settings : 115200n8
- Power : 12VDC 1.5A
Flash instruction using factory.bin image:
1. boot WSR-2533DHPLS normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
firmware update page
("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
button
Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPLS
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPLS downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing
Notes:
- The embedded addresses in eeprom data in Factory partition have
Buffalo's OUI, but they don't match with the actual addresses
assigned to wlan devices. So fixup addresses by the user-space
script.
root@localhost:/# hexdump -C /dev/mtdblock3 | grep "^0000[08]000\s"
00000000 15 76 a0 00 88 57 ee bc 01 a8 15 76 c3 14 00 80 |.v...W.....v....|
00008000 15 76 a0 00 88 57 ee bc 01 f8 15 76 c3 14 00 80 |.v...W.....v....|
See "MAC addresses" below for actual addresses.
- There are 2x factory*.bin images for different purposes.
- factory.bin : for flashing on OEM WebUI
- factory-uboot.bin: for flashing on OEM bootloader or initramfs image
factory-uboot.bin is useful for recoverying the device, or refreshing
when the kernel partition is expanded in the future. sysupgrade on
this device accepts factory-uboot.bin with option "-F", but on that
situation, user configurations won't be kept, so it's not for normal
use.
MAC addresses:
LAN : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
WAN : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
2.4 GHz: 90:96:F3:xx:xx:31
5 GHz : 90:96:F3:xx:xx:38
[original work]
Signed-off-by: Audun-Marius Gangstø <audun@gangsto.org>
[convert to ubi, fix/improve DT, add sysupgrade support]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Switch trx parser to parser_trx of Linux Kernel from mtdsplit_trx to
split firmware partition using model-specific trx magic number on
some Buffalo devices.
This change is tested on Buffalo WSR-2533DHPL.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Move Build/buffalo-trx to image-commands.mk from image/mt7622.mk to use
that definition from ramips as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This pull request ports Ruijie RG-X60 Pro router support to the main branch.
Parameters:
- SoC : MediaTek MT7986A Quad-core ARM Cortex-A53 2.0GHz
- RAM : DDR3 512MiB (W634GU6QB)
- Flash : SPI-NAND 128 MiB (W25N01GVZEIG)
- WLAN : MediaTek MT7986A integration dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 4x4
- 5 GHz : a/n/ac/ax, MIMO 4x4
- Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
2500Mbps x 1 (Realtek RTL8221B-VB-CG)
- UART : through-hole on PCB
- [J500] GND, TX, RX, 3.3V (115200n1)
- Buttons : Mesh, Reset
- LEDs : 1x Power (Blue)
1x Turbo (Purple)
- Power : 12 VDC, 3 A
How to Installation:
1. Remove the case and connect the TTL cable to the corresponding position.
2. Power on the device and quickly press "down" on the keyboard, then
U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Openwrt image file name to be
flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.
How return to stock:
1. Remove the case and connect the TTL cable to the corresponding
position.
2. Power on the device and quickly press "down" on the keyboard, then
U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Stock “E-WEBOS” image file name to
be flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.
About recovery:
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.
About MAC Address:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 10:82:3D:XX:XX:9E | label |
| LAN | 10:82:3D:XX:XX:9F | label+1 |
| WLAN 2g | 10:82:3D:XX:XX:A0 | label+2 |
| WLAN 5g | 10:82:3D:XX:XX:A1 | label+3 |
+---------+-------------------+-----------+
Signed-off-by: Ashley Lee <code@emtips.net>
The Yafut tool now has limited capabilities for working on filesystem
images stored in regular files. This enables preparing Yaffs2 images
for devices with NOR flash using upstream Yaffs2 filesystem code instead
of the custom kernel2minor tool.
Since minimizing the size of the resulting filesystem image size is
important and upstream Yaffs2 code requires two allocator reserve blocks
to be available when writing a file to the filesystem, a trick is
employed while preparing an OpenWRT image: the blank filesystem image
that Yafut operates on initially contains two extra erase blocks that
are chopped off after the kernel file is written. This is safe to do
because Yaffs2 has a true log structure and therefore only ever writes
sequentially (and the size of the kernel file is known beforehand).
While the two extra erase blocks are necessary for writes, Yaffs2 code
seems to be perfectly capable of reading back files from a "truncated"
filesystem that does not contain these extra erase blocks.
In terms of image size, this new approach is only marginally worse than
the current kernel2minor-based one: specifically, upstream Yaffs2 code
needs to write three object headers (each of which takes up an entire
data chunk) when the kernel file is written to the filesystem:
- an object header for the kernel file when it is created,
- an object header for the root directory when the kernel file is
created,
- an updated object header for the kernel file when the latter is
fully written (so that its new size can be recorded).
kernel2minor only writes two of these headers, which is the absolute
minimum required for reading the file back. This means that the
Yafut-based approach causes firmware images to be at most one erase
block (64 kB) larger than those created using kernel2minor, but only in
the very unfortunate scenario where the size of the kernel file is
really close to a multiple of the erase block size.
The rest of the calculations performed when the empty filesystem image
is first prepared stems from the Yaffs2 layout used by MikroTik NOR
devices: each 65,536-byte erase block contains 63 chunks, each of which
consists of 1024 bytes of data followed by 16-byte Yaffs tags without
ECC data; each such group of 63 chunks is then followed by 16 bytes of
padding, which translates to "-C 1040 -B 64k -E" in the Yafut
invocation. Yaffs2 checkpoints and summaries are disabled (using
Yafut's -P and -S switches, respectively) as they are merely performance
optimizations that require extra storage space. The -L and -M switches
are used to force little-endian or big-endian byte order (respectively)
in the resulting filesystem image, no matter what byte order the build
host uses. The tr invocation is used to ensure that the filesystem
image is initialized with 0xFF bytes (which are an indicator of unused
space for Yaffs2 code).
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Link: https://github.com/openwrt/openwrt/pull/13453
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of extracting WiFi precal as well as MAC addresses in userspace
use recently introduced NVMEM-on-UBI instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB XMC 25QH128CH10
- RAM: 128 MiB ESMT M14D1G1664A
- WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- USB 2.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: unpopulated header, 115200 8n1
- Power: 5 VDC, 2 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x0 | label |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.
To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.
If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.
Signed-off-by: Luis Mita <luis@luismita.com>
For MT7620, we should always prevent main ethernet interface from
going down due to phy link changes. And the ralink net driver does
not support cable test function, so this patch won't change any
behavior.
Ref:
6fcba5eec3 ("ramips: port 0034-NET-multi-phy-support.patch to 5.4")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15591
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
CI tells us that we need to, so lets refresh them.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Select 6.6 as testing kernel on bcm47xx.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since 6.1 is now default, drop 5.15 support.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Default to kernel 6.1 on bcm47xx.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel patches. Remove patches already included in the kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15580
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for D-Link DIR-2055 A1 based on similarities to DIR-1960 A1,
as well as various DIR-8xx A1 models. Existing DIR-1960 A1 openwrt
"factory" firmware installs without modifications via the D-Link Recovery
GUI and has no known incompatibilities with the DIR-2055 A1.
Changes to be committed:
new file: target/linux/ramips/dts/mt7621_dlink_dir-2055-a1.dts
modified: target/linux/ramips/image/mt7621.mk
modified: target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
modified: target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
Specifications:
Board: Not known
SoC: MediaTek MT7621 Family (MT7621AT)
RAM: 256 MB (Micron 9OK17 D9PTK, should be DDR3 MT41K128M16JT-125)
Flash: 128 MB (Winbond W29N01HVSINA)
WiFi: MediaTek MT7615 Family (MT7615N x2)
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0 (front)
Buttons: Reset, WiFi Toggle, WPS
LEDs: Power (white/orange), Internet (white/orange),
WiFi 2.4G (white), WiFi 5G (white)
Notes:
Only known difference vs. the DIR-1960 A1 is that the DIR-2055 A1
doesn't have a USB activity LED
Serial port:
Tested to be identical to various DIR-8xx A1 models with a similar
enclosure/pcb design:
Parameters: 57600, 8N1, 3.3V TTL no flow control
Location: J1 header (close to the Reset, WiFi and WPS buttons)
Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND
Did not connect VCC when using
Installation:
D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to
http://192.168.0.1
Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Keith Harrison <keithh@protonmail.com>
The option CONFIG_SND_DRIVERS is activated by default in the generic
configuration, do not deactivate it for tegra. This fixes the build of
the kmod-sound-dummy package on tegra.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Split the kmod-video-dma into kmod-video-dma-sg and
kmod-video-dma-contig. The old one contained two kmods, but sometimes
only one of them is build which caused problems. The configuration
options are not manually selectable in the kernel and hidden in OpenWrt.
Currently this causes build failures on some targets.
Fixes: 4d7cbe0a55 ("kernel: video-dma: explicitly state packaged modules")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We don't have any passive trip point hence we can set the polling delay
for passive trip to 0 effectively disabling this polling.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Split thermal zone for puzzle chassis. Thermal platform supports only
one sensor per thermal zone.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix missing property in puzzle thermal. The thing was never supposed to
work.
Property #thermal-sensor-cells was missing from the puzzle hwmon, making
the entire thermal platform referencing that fail to probe with -EINVAL.
The puzzle hwmon expose 2 termistor but they probably use an userspace
downstream utility to configure and handle thermal. For this reason we
really don't know what they use the sensor for or when it's attached.
We use them to sensor if the Chassis gets too hot due to ambient
temperature and generic components getting too warm.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- Make step_wise thermal governor respect hysteresis
This is done by importing a downstream patch, backporting the same feature
now present in Linux v6.10+ would be too messy.
- Introduce thermal zone for the WT61P803 uC (chassis and board sensors)
- Introduce thermal zones for AQR NBase-T PHYs
- No longer modify existing SoC thermal zones (which are now only in charge
for emergency shutdown, and can be interrupt driven instead of polled)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Hardware
--------
CPU: Freescale P1020 2xe500 PPC
RAM: 256M DDR3 (Micron MT41J64M16JT-15E:G "D9MNJ")
NAND: 128M (Micron 2CA1)
BTN: 1x Reset
LED: Power - ETH - Radio1 - Radio2
UART: RJ-45 Cisco Pinout - 115200 8N1
Installation
------------
NOTE: You can find a repo with up-to-date instructions as well as
the required files here:
https://github.com/blocktrron/msm460-flashing
Required files
==============
You need a command-files as well as a U-Boot image.
The command-file has the following content (padded to 131072 bytes).
If you copy paste these, remove the newlines!
```
U-BOOT setenv ethaddr 02:03:04:05:06:07; setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x3000000 msm460-uboot.bin;
nand device; nand erase 0 0xC0000; nand write 0x3000000 0x0 0xC0000; reset
```
You can download the required U-Boot from this repository:
https://github.com/blocktrron/u-boot-msm/releases
Preparation
===========
Prepare a TFTP server serving two files:
- U-Boot NAND image as `msm460-uboot.bin`.
- OpenWrt factory image as `msm460-factory.bin`
- Command-file names `commands.tftp`
You can start a TFTP server in the current directory using dnsmasq:
```bash
sudo dnsmasq --no-daemon --listen-address=0.0.0.0 \
--port=0 --enable-tftp=enxd0 --tftp-root="$(pwd)" \
--user=root --group=root
```
Replace `enxd0` with the name of your network interface.
Procedure
=========
1. Assign yourself the IP-Address 192.168.1.66/24.
3. Connect the Router to the PC while keeping the reset button
pressed.
4. The LEDs will eventually begin to flash.
They will start to flash faster after around 15 seconds.
5. Release the reset button.
6. Start a new shell
7. Make sure you are currently in the directory where the tftp server
is located.
8. Run the following command:
```bash
tftp 192.168.1.1 -m binary -c put commands.tftp nflashd.cccc9999
```
You get the message "Transfer timed out."
To find out if you have been successful, please check the
blinking LED Pattern.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a universal zImage which can be loaded by mpc85xx boards at
load address 0x3000000. This allows boards to boot kernels larger than
16MB even if the image is loaded temporarily from NAND at offset
0x1000000 which some bootloaders do by default.
Signed-off-by: David Bauer <mail@david-bauer.net>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6702 @1GHz
- 256Mb RAM
- 128Mb NAND
- 1x GbE LAN (Marvell 88E1318R)
- 1x USB 2.0
- 2x SATA
- Weltrend WT69P3 ("supervisor" MCU chip)
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Notes:
- The Weltrend MCU is controlled by the package added in utils/dns320l-mcu.
- The original MAC address is stored in the "mini firmware" image's first
17 bytes.
- Compared to the original MTD layout, the uImage+rootfs are now stored in
a common ubi partition.
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b u-boot-dns320l/u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 u-boot-dns320l/u-boot.kwb
(Please note that "PHY reset timed out" seems to be customary
on kirkwood devices, the egiga0 interface works regardless.)
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-generic-dlink_dns320l-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Upstream commit 83b7f0b8aeab ("ARM: tegra: Add OPP tables and power
domains to Tegra20 device-trees") added power domains to all devices
supporting power management and one of them is Video Decoder Engine.
Because of lacking driver for VDE, its power gate couldn't be driven
which inhibited reboot of the whole device.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Simple refresh to get rid of any fuzz and drop serial patch. With few
bug fixes around tegra serial driver the spurious IRQ didn't appear any
more during test. Let's see how long that'll last.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Use a simple Shell script like on filogic target to get rid of downstream
patch for the Ethernet driver which was rejected upstream long ago.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds the legacy /dev/fb* device file for kernel 6.6 again.
Linux upstream commit 701d2054fa31 ("fbdev: Make support for
userspace interfaces configurable") made this configurable and we
deactivated this option by default for kernel 6.6. On x86 we are not
space constrained and some users need this legacy interface.
Fixes: #15222
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport commit fixing detection of SFP modules which has been broken
since Linux 6.4 for some modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In preparation to update to upcoming Linux 6.6.33 move accepted patches
from mediatek target to backport folder, so moving to newer Linux 6.6
releases becomes easier and also other patches on top can be applied
more easily.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure all patches can again be applied using 'git am' on the
corresponding linux-stable git tree.
Fixes: a7ae4ed0a3 ("kernel: fix tools build breakage on macos with x86")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Fix compile error:
drivers/dma/ralink-gdma.c: In function 'gdma_dma_config':
drivers/dma/ralink-gdma.c:197:40: error: 'struct dma_slave_config' has no member named 'slave_id'
197 | chan->slave_id = config->slave_id;
| ^~
drivers/dma/ralink-gdma.c:206:40: error: 'struct dma_slave_config' has no member named 'slave_id'
206 | chan->slave_id = config->slave_id;
| ^~
make[8]: *** [scripts/Makefile.build:243: drivers/dma/ralink-gdma.o] Error 1
ref: https://lore.kernel.org/all/20211122222203.4103644-1-arnd@kernel.org/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The gdma driver has been removed from the upstream. Let's move it
to the local files. This patch also removed unsupported compatible
string and sub-target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add missing ';;' to the end of shell switch case statement.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Reported-by: @gl-dude
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Disable image building for the board, since the kernel of the main branch
is to big to fit into the kernel partition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Dell/SonicWall APL26-0AE (marketed as SonicPoint ACe) is a dual band
wireless access point. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 2x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
All described procedures were done in following environment:
ROM Version: SonicROM (U-Boot) 8.0.0.0-11o
SafeMode Firmware Version: SonicOS 8.0.0.0-14o
Firmware Version: SonicOS 9.0.1.0
In case of other versions, following installation instructions might be
ineffective.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "sp_fw.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 sp_fw.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
This device has Winbond 25Q256FVFG and doesn't have reliable reset, which
causes hang on reboot, thus broken-flash-reset needs to be added. This
property addition causes dispaly of "scary" warning on each boot, take
this warnig into consideration.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
After the spliting dts folder of ARM architecture in upstream,
layerscape routines need to be adjusted for new solution.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Mostly done by 'make kernel_oldconfig'.
armv8_64b has added one entry manually:
CONFIG_CRYPTO_CURVE25519=y
as workaround for error:
aarch64-openwrt-linux-musl-ld: crypto/crypto_engine.o: in function
`crypto_engine_register_kpp':
crypto_engine.c:687: undefined reference to `crypto_register_kpp'
crypto_engine.c:687:(.text+0x57c): relocation truncated to fit:
R_AARCH64_CALL26 against undefined symbol `crypto_register_kpp'
aarch64-openwrt-linux-musl-ld: crypto/crypto_engine.o: in function
`crypto_engine_unregister_kpp':
crypto/crypto_engine.c:693: undefined reference to `crypto_unregister_kpp'
crypto_engine.c:693:(.text+0x5a0): relocation truncated to fit:
R_AARCH64_CALL26 against undefined symbol `crypto_unregister_kpp'
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Fortinet FortiWiFi 51E (FWF-51E) is a UTM with 1x WLAN and 1x SSD, based
on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- WLAN : Fortinet EMP7618-FT (Atheros AR9382 (2T2R))
- interface : MiniPCIe
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FWF-51E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
WLAN : 88:DC:96:xx:xx:xx (MiniPCIe Card)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
Fortinet FortiWiFi 50E-2R (FWF-50E-2R) is a UTM with 2x WLAN, based on
Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Nanya NT5CC512M8EN-EK)
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- WLAN : Gemtek WMDQ-177ACN (Qualcomm Atheros QCA9892 (2T2R))
(2x)
- interface : MiniPCIe
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FWF-50E-2R and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
WLAN 1: 1C:49:7B:xx:xx:xx (MiniPCIe Card)
WLAN 2: 1C:49:7B:xx:xx:xx (MiniPCIe Card)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
Fortinet FortiGate 52E (FG-52E) is a UTM, based on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 64 GB (2x A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-52E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Fortinet FortiGate 51E (FG-51E) is a UTM, based on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-51E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 70:4C:A5:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:99
WAN 2 : 70:4C:A5:xx:xx:9A
LAN 1 : 70:4C:A5:xx:xx:9B
LAN 2 : 70:4C:A5:xx:xx:9C
LAN 3 : 70:4C:A5:xx:xx:9D
LAN 4 : 70:4C:A5:xx:xx:9E
LAN 5 : 70:4C:A5:xx:xx:9F
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
Add a new dtsi which contains the common parts of Fortinet
FortiGate/FortiWiFi 5xE series devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add a new dtsi which contains the common parts of Fortinet
FortiGate/FortiWiFi 3xE series devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Rename the common dtsi of Fortinet FortiGate 30E/50E for the preparation
of adding support for the other FortiGate/FortiWiFi 3xE/5xE devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add a common definition of Fortinet FortiGate devices to
image/cortexa9.mk for a preparation of adding support for
other FortiGate 3xE/5xE devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware:
SoC: Qualcomm Atheros QCA956X ver 1 rev 0
CPU clock: 775.000 MHz
Memory: 128 MB DDR2
Flash: 32 MB SPI NOR mx25l25635e
Switch: Atheros AR8327 rev. 4
Ethernet: 5x 10/100/1000 Mbps (1 WAN + 4 LAN)
Buttons: 1x Reset
Serial: TX, RX, GND, VCC
Baudrate: 115200
Wifi: Qualcomm Atheros qca988x 802.11ac/n - 3x3
Qualcomm Atheros AR9561 802.11b/g/n - 3x3
Not working:
Leds: 1x via a SPI controller
Display: ST7789V or ILI9341V
controlled by stm32f205.
Note:
DSA changes are ready, but we have an issue with
ports not working after 20-30 minutes. So for now
we use swconfig.
Installation: serial connection only
There is a J11 four pin connector. You need to connect TX, RX and GND.
You can find very good information about the device here
https://github.com/alexanderhenne/AFi-R?tab=readme-ov-file#finding-j11
Upgrading via serial port:
1. Download the kernel initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN1 port to your PC LAN
3. Stop autoboot to get to U-boot shell
Interrupt the autoboot process by pressing any key when prompted
4. Transfer the kernel image with TFTP
Set your ip address on your TFTP server to 192.168.1.254
# tftpboot 0x81000000 amplifi-router-hd-initramfs-kernel.bin
5. Load the image
# bootm 0x81000000
6. SCP sysupgrade image from your PC to the Amplifi HD
(If you use a newer mac use scp -O)
# scp openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Write sysupgrade to the firmware partition
# mtd write /tmp/openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin firmware
8. Reboot your device
# reboot
Credit to alexanderhenne for all the information.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
ELECOM WRC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB
- Flash : RAW-NAND 128 MiB (Macronix MX30LF1G28AD-TI)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D)
- Ethernet : 5x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO) : 7x/4x
- UART : pin-header on PCB ("J5")
- arrangement : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs-factory image:
1. Boot WRC-X1800GS normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. After flashing initramfs-factory image and reboot, upload the
sysupgrade image and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- WRC-X1800GS has 2x os images. Those are switched on every firmware
updating on stock firmware, but dual-boot feature on this device
cannot be handled on OpenWrt. So the 1st image is always used on
OpenWrt.
This is controlled by "bootnum" variable embedded in "persist"
partition (addr: 0x4).
- WRC-X1800GS has 2x HW revisions. There are some small changes, but the
same DeviceTree in stock firmware is used for both revisions.
On this support of WRC-X1800GS, 2x green:wlan-2g-N LEDs are defined
for each revision and the same default triggers are set.
MAC addresses:
LAN : 38:97:A4:xx:xx:38 (Factory, 0x1fdfa (hex) / Ubootenv, ethaddr (text))
WAN : 38:97:A4:xx:xx:3B (Factory, 0x1fdf4 (hex))
2.4 GHz: 38:97:A4:xx:xx:39
5 GHz : 38:97:A4:xx:xx:3A
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The EnGenius EAP1300 and EAP1300EXT use identical boards and firmware
(as flashed) from the vendor.
As with the EAP1300, the EAP1300EXT requires a specific firmware version
to flash OpenWRT. Unfortunately, the required firmware is truncated on
the vendor's website.
A working file can be created as follows:
```
curl \
https://www.engeniustech.com/wp_firmware/eap1300-all-v3.5.3.5_c1.9.04.bin \
| perl -pe 's/\x09EAP1300_A/\x0cEAP1300EXT_A/' \
> eap1300ext-all-v3.5.3.5_c1.9.04.bin
```
The file should have sha256:
`58a1197a426139a12b03fd432334e677124cbe3384349bd7337f2ee71f1dcfd4`.
Please see commit 2b4ac79 for further
details.
The vendor firmware must be decrypted before it can be flashed from
OpenWRT. A tool able to do that is available from:
https://github.com/ryancdotorg/enfringement/blob/main/decrypt.py
Signed-off-by: Ryan Castellucci <code@ryanc.org>
The vendor U-Boot on the Cudy M3000 and the Yuncore AX835 assign random
mac addresses on boot and set the 'local-mac-address' property which
prevents Openwrt from assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add the
property, removes the workaround from 02_network, and adds back the nvmem
definition for the M3000.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
OpenWrt supported the D-Link DSM G600 A in the past. It has
64 MB of RAM and 16 MB of flash so it will run just fine,
and should be quite usable with a rootfs on an external
harddrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OpenWrt supported the Freecom FSG-3 in the past. It has
64 MB of RAM so will run fine, but the bare 4 MB of flash
makes it a non-default target. The generated compressed
image is currently below 4MB (just 3.3 MB) though, so it
should be possible to flash just fine with a rootfs on
a harddrive or USB stick, which is what the FSG-3 used
in the past as well.
The device has a WAN port on eth0 and three LAN ports on
eth1. The LAN ports are probably a DSA switch but the
old OpenWrt base never activated that, instead it relies
on boot defaults.
Due to questionable usablity without tweaking and further
work this image is not built by default, but made available
for developers who know what they are doing.
The TAR+CRC image generation is a rewritten version of the
earlier support code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OpenWrt supported the Iomega NAS100D in the past and it has
64 MB of RAM so if booted from a harddrive it will probably
work just fine. The APEX boot loader already has a build
variant for this machine that we can just pick up and use.
This device has a single ethernet port so bring this online
with DHCP as expected for a NAS device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several of the IXP4xx machines mount root on external harddrives
so add EXT4 and rootfs-part to the featureset so the right
features are always selected.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Common specifications:
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 1x 10000M/1000M/100M + 3x 1000M/100M/10M LAN ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* Airoha AG3352 GPS
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for each 1G port, 3x LED for each 10G port
* USB 3.0 type A port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
SDG-8733: 1x 10000M/1000M/100M WAN port
SDG-8734: 1x USXGMII/10GBase-R/5GBase-R/2500Base-X/1000Base-X/SGMII SFP+
Both models are also available in versions including 2x FXS POTS interfaces
for analog phones. Those interfaces are not supported by OpenWrt.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing call to emmc_copy_config which either writes the sysupgrade
tar.gz backup file or clears the existing rootfs_data overlay.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch adding support for the AQR114C PHY and add support for
PHY LEDs and polarity setting of Aquantia 3rd and 4th generation PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Carambola3 is a WiFi module based on Qualcomm/Atheros QCA4531
http://wiki.8devices.com/carambola3
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- 1x USB 2.0 Host socket
- UART for serial console
- 12x GPIO
Flash instructions:
Upgrading from ar71xx target:
- Upload image into the board:
scp openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin \
root@192.168.1.1/tmp/
- Run sysupgrade
sysupgrade -F /tmp/openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin
Upgrading from u-boot:
- Set up tftp server with openwrt-ath79-generic-8dev_carambola3-initramfs-kernel.bin
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
setenv serverip 192.168.1.254
- Set device ip from the same subnet
setenv ipaddr 192.168.1.1
- Copy new firmware to board
tftpboot 0x82000000 initramfs.bin
- Boot OpenWRT
bootm 0x82000000
- Upload image openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin into the board
- Run sysupgrade.
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/15514
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
CPU: MT7628AN 580MHz
RAM: 64MB DDR2
FLASH: 8MB EN25QH64 NOR SPI
WIFI: 2.4GHz 2x2 MT7628 b/g/n internal
WIFI: 5GHz 1x1 MT7610E ac/n PCI
LTE: Qualcomm MDM9207
ETH: 4xLAN 100base-T integrated
SWITCH: RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
LEDS: LAN, WAN, Power, 3x signal strength, WiFi
BTNS: Reset, WiFi toggle
UART: Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1
Installation:
1. Update using recovery mode
- set your IP to 192.168.0.225, subnet mask: 255.255.255.0
- start tftp server, rename tftp-recovery.bin to
tp_recovery.bin and place it into the server's directory
- while holdig the "reset" button, power on the device
- keep holding "reset" until the file is being transferred
Notes:
This board has only one MAC address programmed
in the "romfile" partition:
- MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
- MAC for phy1 (5GHz) at romfile 0xf100 (-1)
- stock firmware re-uses phy0 MAC for ethernet
- stock firmware uses romfile 0xf100 (1) for WWAN;
not used since QMI interface is raw IP
Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
mt7915e driver supports MT7915 & MT7916 devices and MT7981 & MT7986
on-SoC wireless controllers. Devices based on MT7988 and possibly other
next chipsets are quite unlikely to need it (MT7988 was designed to be
used with MT7996).
Move kmod-mt7915e to DEVICE_PACKAGES of relevant devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Currently, in case that PSGMII calibration fails it will panic the kernel
which is not ideal and is preventing any debugging to be done.
So, since PGMII calibration failing only means that wired networking wont
work lets convet the panic() call to dev_error.
Link: https://github.com/openwrt/openwrt/pull/15542
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that on Spectrum SAX1V1K QCA8081 is being brought out of reset
too quickly and thus causing it to get stuck in an invalid autoneg
register configuration mode.
Setting an deasset delay seems to fix this, so lets set it.
Fixes: #15493
Link: https://github.com/openwrt/openwrt/pull/15541
Signed-off-by: Robert Marko <robimarko@gmail.com>
filogic: Add support for D-Link AQUILA PRO AI M30
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 1GB RAM
- 16MB NOR
- 128MB NAND
- 3 LEDs (red, green, blue, white)
- 2 buttons (reset, user defined)
- 1 2.5Gbit WAN port (Airoha EN8811h)
- 1 1Gbit LAN ports
- 1 single lane M.2 SSD slot
- 1 mikroBus socket
- externel HW WDT (25s refresh time)
- i2c RTC (with battery backup)
Serial Interface
- UBS-C CDC-ACM
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
MAC addresses are not populated on the early samples.
Signed-off-by: John Crispin <john@phrozen.org>
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.
Bring in some outstanding patches.
Tested on the Gateworks GW2348-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These patches have partial acceptance upstream and are still
a WIP, now there is merge window for kernel v6.10 so these
will not be reposted until that is over. In the meantime,
let's add the current state to OpenWrt so the ethernet on
Gemini is up and working (tested on several devices).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add ubi volumes for mt7988a-rfb and support for using factory data
for Ethernet MAC addresses and MT7996 WLAN calibration data.
Also add rootdisk handle. Removes the need to keep using nmbm
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Without serial or network access the only option for initial
configuration, is a attached display with USB keyboard, but the keyboard
driver needs to be installed first. So enable keyboard driver by default
to avoid this issue.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Because recent changes to procd, last "console" argument was used as
primary argument and causing no terminal to be spawned on serial
interface. So drop the hardcoded consoles in boot script, since dts has
already an alias specified, which lets procd decide where to spawn the
terminal.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
The old overlay remained after upgrades and would cause failure on first
boot after upgrade, in which no new overlay could be created while old
one was unusable.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define common Linksys MX device for MX4200v1/v2 and MX5300.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove gpio16 from the default NAND pinctrl configuration
as its unused and only needed for LCD.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
All three PCIe ports are reported non working on Meraki MR42/MR52 boards
since kernel 6.1 with the issue of PCIe PHY link never coming up thus
no WLAN cards are available on the boards.
After debugging it seems that PCIe worked on 5.15 and older purely by
accident as device DTS was using /delete-property/ perst-gpios; in each
of the 3 PCIe nodes but there was no "perst-gpios" property in the SoC DTSI
as it was still using the older "perst-gpio" property so it was not getting
removed from the device DTS.
However, in kernel 6.1 commit ("ARM: dts: qcom-*: replace deprecated
perst-gpio with perst-gpios") updated all Qualcomm DTS-es to use the newer
"perst-gpios" and thus once ipq806x moved to 6.1 PCIe stopped working as
now that property was being dropped from the device DTS.
So, since the removal of PERST pins seems to have been wrong from the start
lets drop the property removal from MR42/MR52.
Fixes: #15408
Link: https://github.com/openwrt/openwrt/pull/15509
Signed-off-by: Robert Marko <robimarko@gmail.com>
Our kernel export stripping has been broken on 6.6 from the start since
upstream kernel really reworked stuff in ("kbuild: generate KSYMTAB entries
by modpost") and other commits as well.
So, until this is either fixed or reworked lets drop the patch as it doesnt
make sense to carry it knowing its broken and it can always be easily
restored.
Link: https://github.com/openwrt/openwrt/pull/15498
Signed-off-by: Robert Marko <robimarko@gmail.com>
This code assumed that the mt7628an_tplink_8m.dtsi file defines
mediatek,mtd-eeprom for the wmac and sets status to okay.
The mediatek,mtd-eeprom definition was removed in commit e93f41adee
("ramips: convert MT7628 EEPROM to NVMEM format") but the dts for these
two devices was not adapted to include the eeprom position on its own.
The status = "okay" property was removed in 0a1d15642f ("ramips:
mt7628: use nvmem-layout"), but the property was not added to these dts
files.
Without this change wifi does not work for these devices.
Fixes: e93f41adee ("ramips: convert MT7628 EEPROM to NVMEM format")
Fixes: 0a1d15642f ("ramips: mt7628: use nvmem-layout")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linux kernel commit 90c2d2eb7ab5 ("MIPS: pci: lantiq: switch to using
gpiod API") not only switched to the gpiod API, but also inverted /
changed the polarity of the GPIO.
According to the PCI specification, the RST# pin is an active-low
signal. However, most of the device trees that have been widely used for
a long time (mainly in the openWrt project) define this GPIO as
active-high and the old driver code inverted the signal internally.
Apparently there are actually boards where the reset gpio must be
operated inverted. For this reason, we cannot use the GPIOD_OUT_LOW/HIGH
flag for initialization. Instead, we must explicitly set the gpio to
value 1 in order to take into account any "GPIO_ACTIVE_LOW" flag that
may have been set.
In order to remain compatible with all these existing device trees, we
should therefore keep the logic as it was before the commit.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Use dev_err_probe() to get rid of the following warning which is
seen when the PCIe PHY has not been probed yet:
pcie-xrx200 1d900000.pcie: failed to get the PCIe PHY
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This backports some patches for the gswip switch driver.
I copied them from this repository:
https://github.com/xdarklight/linux/commits/lantiq-gswip-integration-20221022
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[drop some patches which may break functionality at the moment]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
If the reverted timer driver fails to allocate interrupts handle the
error better.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[moved printk before the cleanup for-loop]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Make all the patches apply and delete the ones already integrated into
upstream Linux kernel. This also refreshes some of the kernel
configurations.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[refreshed for linux 6.1.89]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This refreshes the configuration for Linux kernel 5.15.
I first selected the xrx200 subtarget and then refreshed the target
kernel configuration using this command:
make kernel_oldconfig CONFIG_TARGET=target
Then I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
I compared the kernel configuration used to compile the kernel from the
build directory for each subtarget before and after this task and it was
still the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[refreshed config for linux 5.15.158]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
There is a custom LED controller between the 3 SoC GPIO outputs and
the red and blue LEDs of the device. It implements a strange mapping
that includes fixed, flashing, and breathing modes.
The current DTS configuration causes OpenWrt to flash the LEDs over
the controller's own flashing, resulting in chaotic output in boot,
failsafe, and upgrade modes.
This change fixes the LEDs in the best way possible as long as each
OpenWrt running state is limited to be signaled by a single led.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15440
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is no need to use 'list_for_each_entry_safe' here, as nothing is
removed from the list in the 'for' loop.
Use 'list_for_each_entry' instead, it is slightly less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://github.com/openwrt/openwrt/pull/15435
Link: https://github.com/openwrt/openwrt/pull/15435
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes the issue of RTL8221B-VB-CG not being detected correctly.
Reverts changes from f6c27b2, leaving only the read_c45 test.
Fixed: #15093
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Lets give Linux 6.6 a try.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel config for Linux 6.6.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh the only remaining downstream patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update default kernel version to 6.6 and drop configs and patches for
kernel 6.1. We can also omit the conditional to include DTS dir.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/15449
Signed-off-by: Robert Marko <robimarko@gmail.com>
Like AVM 1200 these devices also do not use QCA807x PHY at all and thus
they disables all of the individual PHY nodes, however this is not enough
anymore since the conversion to PHY package.
Now its now enough to disable the PHY-s in the package alone, but the PHY
package node itself must also be disabled.
Fixes: 1b931c33a2 ("ipq40xx: adapt to new Upstream QCA807x PHY driver")
Link: https://github.com/openwrt/openwrt/pull/15444
Signed-off-by: Robert Marko <robimarko@gmail.com>
- Soc: MediaTek MT7621AT
- RAM: 512 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7905DAN, MediaTek MT7975DN
- Ethernet: 1 WAN, 3 LAN (Gigabit)
- Buttons: Reset, Joylink
- LEDs: (red, blue, green), routed to one indicator in the top of the
device
- Power: DC 12V 1A tip positive
- 1 TF Card Slot
The pins for the serial console are already labeled on the board
J4(V, R, T, G). Serial settings: 3.3V, 115200
MAC addresses:
| | MAC | Algorithm |
| ------- | ----------------- | --------- |
| label | dc:d8:xx:xx:xx:01 | label |
| LAN | dc:d8:xx:xx:xx:01 | label |
| WAN | dc:d8:xx:xx:xx:02 | label+1 |
| WLAN 2g | dc:d8:xx:xx:xx:03 | label+2 |
| WLAN 5g | de:d8:xx:xx:xx:04 | label+3 |
1. rename the
openwrt-ramips-mt7621-jdcloud_re-cp-02-squashfs-sysupgrade.bin
to JDCOS.bin
2. start a TFTP server from IP address 192.168.68.10 and serve the
image named JDCOS.bin
3. connect your device to the LAN port
4. power up the router and press any key on the console to interrupt
the boot process.
5. enter the following commands on the router console
1. setenv bootcount 6
2. saveenv
3. reset
> NOTE: wait for the restart, it will automatically fetch the
> image named JDCOS.bin from the TFTP server and write it into
> the flash. After the writing is completed, the router will be
> automatically restarted.
Unable to recognize large-capacity TF card, see #14042. But the patch
https://github.com/openwrt/openwrt/issues/14042#issuecomment-1910769942
works
Co-Authored-By: Jianti Chen <clbcjt@outlook.com>
Signed-off-by: Sheng Huang <shenghuang147@gmail.com>
Hardware:
SoC: MT7981b
RAM: 256 MB
Flash: 128 MB SPI NAND
Ethernet:
1x 2.5Gbps (rtl8221b)
1x 1Gbps (integrated phy)
WiFi: 2x2 MT7981
Buttons: Reset, WPS
LED: 1x multicolor
Solder on UART:
- remove rubber ring on the bottom
- remove screws
- pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
- remove the (3) screws holding the board in the frame
- remove the board from the frame to get to the screws for the silver, flat heat shield
- remove the (3) screws holding the heat shield
- solder UART pins to the back of the board
- make sure to have the pins point out on side with the black, finned heat spread
- the markings for the pins are going to be below the silver heat shield
- Vcc is not needed
If you don't intend on using the UART outside of the installation process, you might not
want to solder:
- carefully scrape off the thin layer of epoxy on the holes (not the copper)
- place your pin header with the UART attached in the holes
- the pins, starting with the one closest to the socket:
- Vcc (not required)
- GND
- RX
- TX
- either wedge the header or hold it with your fingers so that the pins stay in contact with the board
Installation (UART):
- attach an Ethernet cable to the 1Gbps port (black) on the router
- hold the reset button while powering the router
- press CTRL-C or wait for the timeout to get to the U-Boot prompt
- prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
- use 'tftpboot' in the U-Boot shell to pull the image
- boot the image using 'bootm'
- push the ..-sysupgrade to the router using your preferred method
- perform the upgrade with 'sysupgrade -n'
There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
FCC ID: A8J-EWS660AP
Engenius ENS1750 is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+
Engenius EWS660AP, ENS1750, and ENS1200 are "electrically identical,
different model names are for marketing purpose" according to docs
provided by Engenius to the FCC.
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- QCA9880 WLAN mini PCIe card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- AR8033 PHY SGMII GbE with PoE+ OUT
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)
**MAC addresses:**
Base MAC addressed labeled as "MAC"
Only one Vendor MAC address in flash
eth0 *:d4 MAC art 0x0
eth1 *:d5 --- art 0x0 +1
phy1 *:d6 --- art 0x0 +2
phy0 *:d7 --- art 0x0 +3
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
**Format of OEM firmware image:**
The OEM software of ENS1750 is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-ens1750-uImage-lzma.bin
openwrt-ar71xx-generic-ens1750-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Tested-by: Kevin Abraham <kevin@westhousefarm.com>
Signed-off-by: Kevin Abraham <kevin@westhousefarm.com>
Add additional PWM fan cooling step and enable fan on BPi-R4.
Suggested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
We should setup the registers for trapping LLDP packets to the CPU.
Currently, these packets are forwarded to all ports which is not desired
behaviour.
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
These registers control the handling of Link Layer Discovery Protocol
(LLDP) packets. This seems to be a typo in the naming.
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
This device is similiar to the Wavlink WL-WN531A3.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x Touchlink button
- 1x Turbo button
- 1x Wps button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 5x Blue leds (ethernet ports)
- 1x Power led
- 1x Wifi led
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
In my case the whole device was locked and there was no way
to flash the image, except for flashing directly to the flash
via an spi-flasher. You need to put the sysupgrade image file at
the beginning of 0x60000.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:F0 (factory @ 0x28)
WAN XX:XX:XX:XX:XX:F1 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:F2 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:F3 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:F2
Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
All kernel config files are refreshed by
`make kernel_oldconfig CONFIG_TARGET={subtarget_target,subtarget}`
"CONFIG_SQUASHFS_DECOMP_SINGLE=y" is manually selected as all ath79
SoCs are single core processors.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The upcoming 6.6 kernel will introduce a new upstream generic
"gpio-latch" driver. It will conflict with the downstream MikroTik
GPIO latch driver. Let's rename it to avoid any potential issues.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x0 | |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset
MAC Table
Label xx:xx:xx:xx:xx:EB
LAN xx:xx:xx:xx:xx:EB
2.4Ghz xx:xx:xx:xx:xx:EC
5Ghz xx:xx:xx:xx:xx:ED
WAN xx:xx:xx:xx:xx:EE
Flash instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image
D-Link Recovery GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the recovery mode GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the recovery page for the device at http://192.168.0.1/
6. Use the provided emergency web GUI to upload the recovery.bin to the device
Firefox on Windows in a Private Window (incognito) works me
Internet Explorer mode in Microsoft Edge works for others
seems to not work in Linux or virtual machine on Linux for most
some see success using 'curl -v -i -F "firmware=@file.bin" 192.168.0.1'
Thanks to @frkca and @rodneyrod for testing and pushing for its creation
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Setting the LED name and abandoning the label and using the
function/color syntax for some TP-Link Archer series routers:
Archer C2 v1, Archer C20 v1, Archer C20i and Archer C50 v1
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Abandoning the label and using the function/color syntax for some dlink
dir series routers: dir-1960-a1, dir-2660-a1, dir-2640-a1, dir-3040-a1
and dir-3060-a1
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Rename from mt7621_dlink_dir-xx60-a1.dtsi to mt7621_dlink_dir_nand_128m.dtsi
and associated group name when creating the mt7621.mk image
Co-authored-by: Alan Luck <luckyhome2008@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Continuation of commit 8b66f1a. Set the switch address on the MDIO bus to 31.
This is required for all boards currently working with the mt7530 DSA driver.
Fixes: #15419
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Backport patch merged upstream for rgmii-id support in stmmac-ipq806x.
This is needed for some device that directly connets PHY to the gmac
port and require rgmii-id phy-modes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
