mirror of
https://github.com/openwrt/openwrt.git
synced 2025-04-12 05:41:12 +00:00
ramips: add support for TP-Link Archer MR200v5
Specifications:
CPU: MT7628AN 580MHz
RAM: 64MB DDR2
FLASH: 8MB EN25QH64 NOR SPI
WIFI: 2.4GHz 2x2 MT7628 b/g/n internal
WIFI: 5GHz 1x1 MT7610E ac/n PCI
LTE: Qualcomm MDM9207
ETH: 4xLAN 100base-T integrated
SWITCH: RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
LEDS: LAN, WAN, Power, 3x signal strength, WiFi
BTNS: Reset, WiFi toggle
UART: Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1
Installation:
1. Update using recovery mode
- set your IP to 192.168.0.225, subnet mask: 255.255.255.0
- start tftp server, rename tftp-recovery.bin to
tp_recovery.bin and place it into the server's directory
- while holdig the "reset" button, power on the device
- keep holding "reset" until the file is being transferred
Notes:
This board has only one MAC address programmed
in the "romfile" partition:
- MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
- MAC for phy1 (5GHz) at romfile 0xf100 (-1)
- stock firmware re-uses phy0 MAC for ethernet
- stock firmware uses romfile 0xf100 (1) for WWAN;
not used since QMI interface is raw IP
Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
This commit is contained in:
Lea Teuberth
Hauke Mehrtens
parent
e83a5618d4
commit
2a2f53415e
192
target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v5.dts
Normal file
192
target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v5.dts
Normal file
@ -0,0 +1,192 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7628an.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "tplink,archer-mr200-v5", "mediatek,mt7628an-soc";
|
||||
model = "TP-Link Archer MR200 v5";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
label-mac-device = ðernet;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
lan {
|
||||
function = LED_FUNCTION_LAN;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan {
|
||||
function = LED_FUNCTION_WAN;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power: power {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
signal1 {
|
||||
label = "white:signal1";
|
||||
gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
signal2 {
|
||||
label = "white:signal2";
|
||||
gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
signal3 {
|
||||
label = "white:signal3";
|
||||
gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan {
|
||||
function = LED_FUNCTION_WLAN;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
rfkill {
|
||||
label = "rfkill";
|
||||
gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RFKILL>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <104000000>;
|
||||
m25p,fast-read;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
compatible = "tplink,firmware";
|
||||
label = "firmware";
|
||||
reg = <0x20000 0x7b0000>;
|
||||
};
|
||||
|
||||
partition@7d0000 {
|
||||
label = "config";
|
||||
reg = <0x7d0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7e0000 {
|
||||
label = "romfile";
|
||||
reg = <0x7e0000 0x10000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_romfile_f100: macaddr@f100 {
|
||||
compatible = "mac-base";
|
||||
reg = <0xf100 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@7f0000 {
|
||||
label = "radio";
|
||||
reg = <0x7f0000 0x10000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_radio_0: eeprom@0 {
|
||||
reg = <0x0 0x400>;
|
||||
};
|
||||
|
||||
eeprom_radio_8000: eeprom@8000 {
|
||||
reg = <0x8000 0x200>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&state_default {
|
||||
gpio {
|
||||
groups = "i2c", "p0led_an", "p1led_an", "p2led_an", "p3led_an", "p4led_an", "uart1", "wdt";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
nvmem-cells = <&eeprom_radio_0>, <&macaddr_romfile_f100 0>;
|
||||
nvmem-cell-names = "eeprom", "mac-address";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&esw {
|
||||
mediatek,portdisable = <0x30>;
|
||||
};
|
||||
|
||||
ðernet {
|
||||
nvmem-cells = <&macaddr_romfile_f100 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
mt76@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
nvmem-cells = <&eeprom_radio_8000>, <&macaddr_romfile_f100 (-1)>;
|
||||
nvmem-cell-names = "eeprom", "mac-address";
|
||||
};
|
||||
};
|
||||
@ -606,6 +606,21 @@ define Device/tplink_archer-c50-v6
|
||||
endef
|
||||
TARGET_DEVICES += tplink_archer-c50-v6
|
||||
|
||||
define Device/tplink_archer-mr200-v5
|
||||
$(Device/tplink-v2)
|
||||
IMAGE_SIZE := 7872k
|
||||
DEVICE_MODEL := Archer MR200
|
||||
DEVICE_VARIANT := v5
|
||||
TPLINK_FLASHLAYOUT := 8MLmtk
|
||||
TPLINK_HWID := 0x20000005
|
||||
TPLINK_HWREV := 0x5
|
||||
TPLINK_HWREVADD := 0x5
|
||||
DEVICE_PACKAGES := kmod-mt76x0e uqmi kmod-usb2 kmod-usb-serial-option
|
||||
IMAGES := sysupgrade.bin tftp-recovery.bin
|
||||
IMAGE/tftp-recovery.bin := pad-extra 128k | $$(IMAGE/factory.bin)
|
||||
endef
|
||||
TARGET_DEVICES += tplink_archer-mr200-v5
|
||||
|
||||
define Device/tplink_re200-v2
|
||||
$(Device/tplink-safeloader)
|
||||
IMAGE_SIZE := 7808k
|
||||
|
||||
@ -83,6 +83,10 @@ tplink,archer-c50-v6)
|
||||
ucidef_set_led_wlan "wlan2g" "wlan2g" "green:wlan2g" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "wlan5g" "green:wlan5g" "phy1tpt"
|
||||
;;
|
||||
tplink,archer-mr200-v5)
|
||||
ucidef_set_led_netdev "lan" "lan" "white:lan" "eth0"
|
||||
ucidef_set_led_netdev "wan" "wan" "white:wan" "wwan0"
|
||||
;;
|
||||
tplink,re200-v2|\
|
||||
tplink,re200-v3|\
|
||||
tplink,re200-v4|\
|
||||
|
||||
@ -153,6 +153,11 @@ ramips_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
|
||||
;;
|
||||
tplink,archer-mr200-v5)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "1:lan" "2:lan" "3:lan" "6t@eth0"
|
||||
ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
|
||||
;;
|
||||
tplink,tl-mr3020-v3)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "6@eth0"
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user