When a target configuration has unser Kconfig symbols, the build will
fail when OpenWrt is compiled with V=s and stdin is connected to a tty.
In case OpenWrt is compiled without either of these preconditions, the
build will uscceed with the symbols in question being unset.
Modify the kernel configuration in a way it fails on unset symbols
regardless of the aformentioned preconditions.
Signed-off-by: David Bauer <mail@david-bauer.net>
Calling free for the OF property can result in a kernel panic, as the
buffer in question might be referenced elsewhere. Also, it is not
removed from the tree.
Always allocate a new property and updating the tree with it fixes both
issues.
Fixes commit 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: David Bauer <mail@david-bauer.net>
The EXT4 driver also takes care of EXT2 and EXT3 file systems.
Activating the EXT2 driver kernel config options unlocked some other
ext2 driver related options which OpenWrt did not take care of.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The change which backported the of_get_mac_address() change broke some
patches in the layerscape target so the patches did not apply any more.
This commit makes them apply again and also fixes some other problems
related to this change.
Fixes commit 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The code from ks8851.c was moved to ks8851_common.c, so it was not
backported. This broke the compile of the omap target which uses this
driver.
Fixes commit 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch is backported from linux-arm-kernel [1] to improve situation, when
it was reported that 1.2 GHz variant is unstable with DFS.
It waits to be accepted upstream, however, it waits for Marvell people to respond.
[1] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20210630225601.6372-1-kabel@kernel.org/
Fixes: 7b868fe04a ("Revert "mvebu: 5.4 fix DVFS caused random boot crashes"")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Based on the discussion on the mailing list [1], the patch which was
reverted, it reverts only one patch without the subsequent ones.
This leads to the SoC scaling issue not using a CPU parent clock, but
it uses DDR clock. This is done for all variants, and it's wrong because
commits (hacks) that were using the DDR clock are no longer in the mainline kernel.
If someone has stability issues on 1.2 GHz, it should not affect all
routers (1 GHz, 800 MHz) and it should be rather consulted with guys, who are trying to
improve the situation in the kernel and not making the situation worse.
There are two solutions in cases of instability:
a) disable cpufreq
b) underclock it up to 1 GHz
This reverts commit 080a0b74e3.
[1] https://lists.openwrt.org/pipermail/openwrt-devel/2021-June/035702.html
Fixes: d379476817 ("mvebu: armada-37xx: add patch to forbid cpufreq for 1.2 GHz")
CC: Pali Rohár <pali@kernel.org>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This option is needed e.g. to use strongswan for IPSec.
BTW: This was the only target where this option was disabled.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This uses "hdparm" (if present) to get the harddisk into low
power mode on NAS set-ups.
Cc: Adrian Schmutzler <mail@adrianschmutzler.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on the discussion on the mailing list [1], the patch which was
reverted, it reverts only one patch without the subsequent ones.
This leads to the SoC scaling issue not using a CPU parent clock, but
it uses DDR clock. This is done for all variants, and it's wrong because
commits (hacks) that were using the DDR clock are no longer in the mainline kernel.
If someone has stability issues on 1.2 GHz, it should not affect all
routers (1 GHz, 800 MHz) and it should be rather consulted with guys, who are trying to
improve the situation in the kernel and not making the situation worse.
There are two solutions in cases of instability:
a) disable cpufreq
b) underclock it up to 1 GHz
This reverts commit 080a0b74e3.
[1] https://lists.openwrt.org/pipermail/openwrt-devel/2021-June/035702.html
CC: Pali Rohár <pali@kernel.org>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Follow the recommendations stated in the Turris Omnia DTS for eth2:
"In case SFP module is present, U-Boot has to enable the sfp node above,
remove phy-handle property, and add managed = "in-band-status" property."
The boot script is written in a way, that it works for all U-Boot
versions deployed by the vendor so far (2015.10-rc2, 2019.07).
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Kernel 5.4 receives a reduced set, just to make the SFP cage work.
While we are at it, move the patches accepted upstream to the 0xx series.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Kernel 5.10 receives the complete set of improvements from 5.11/5.12.
While we are at it, move the patches accepted upstream to the 0xx series.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Add the missing CONFIG_KCSAN (disabled). Found while making kernel_oldconfig on
an x86-64 subtarget.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Now that we have a generic sdcard upgrade method, which was copied from
the mvebu platform method, we can switch mvebu to the generic method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
kirkwood build broke due to missing include needed for ETH_ALEN.
Add patch (sent upstream as well) to address that.
Refresh patches for 5.4 and 5.10.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As both the Mi Router 4A (100M) and the Mi Router 4C use the same
label-mac-device, the alias can be moved to the shared dtsi.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
A superflus ')' character has slipped into commit 91a52f22a1. Remove it
to fix build.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MT7622 provides are hardware RNG with upstream Linux driver. Enable
compilation of this driver to make use of the hardware RNG.
Signed-off-by: David Bauer <mail@david-bauer.net>
The GL-X300B is a industrial 4G LTE router based on the Qualcomm
QCA9531 SoC.
Specifications:
- Qualcomm QCA9531 @ 650 MHz
- 128 MB of RAM
- 16 MB of SPI NOR FLASH
- 2x 10/100 Mbps Ethernet
- 2.4GHz 802.11b/g/n
- 1x USB 2.0 (vbus driven by GPIO)
- 4x LED, driven by GPIO
- 1x button (reset)
- 1x mini pci-e slot (vcc driven by GPIO)
- RS-485 Serial Port (untested)
Flash instructions:
This firmware can be flashed using either sysupgrade from the GL.iNet
firmware or the recovery console as follows:
- Press and hold the reset button
- Connect power to the router, wait five seconds
- Manually configure 192.168.1.2/24 on your computer, connect to
192.168.1.1
- Upload the firmware image using the web interface
RS-485 serial port is untested and may depend on the following commit in
the GL.iNet repo:
202e83a32a
MAC addresses as verified by OEM firmware:
vendor OpenWrt address
WAN eth0 label
LAN eth1 label + 1
2g phy0 label + 2
The label MAC address was found in the art partition at 0x0
Based on vendor commit:
16c5708b20
Signed-off-by: John Marrett <johnf@zioncluster.ca>
Add the missing ARM_SCMI_PROTOCOL symbol. Apparently it was exposed
for 5.10.53 with a kernel dependency change.
Missing symbol observed with mediatek/7622 E8450/RT3200 router.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The virtual cable tester depends on the netlink interface for ethtool.
Thus, enable it in the generic kernel configuration.
Signed-off-by: David Bauer <mail@david-bauer.net>
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
bcm27xx-bcm2710 builds are stalling when compiled with V=s.
Explitily disable these unset symbols to avoid stalling
builds.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fixes a unused variable warning:
drivers/of/of_net.c: In function 'of_get_mac_address_mtd':
drivers/of/of_net.c:92:19: warning: unused variable 'prop' [-Wunused-variable]
Signed-off-by: David Bauer <mail@david-bauer.net>
The 1st generation MediaTek PCIe host bridge cannot handle Message
Signaled Interrupts (MSIs). The core PCI code is not aware that MSI is
not available. This results in warnings of the form:
WARNING: CPU: 2 PID: 112 at include/linux/msi.h:219
pci_msi_setup_msi_irqs.constprop.8+0x64/0x6c
Modules linked in: ahci(+) libahci libata sd_mod scsi_mod
gpio_button_hotplug
CPU: 2 PID: 112 Comm: kmodloader Not tainted 5.10.52 #0
Hardware name: Mediatek Cortex-A7 (Device Tree)
Import patches that introduce the 'no_msi' attribute to signal missing
MSI support to the core PCI.
Refresh patches:
- 000-spi-fix-fifo.patch
- 330-mtk-bmt-support.patch
- 510-net-mediatek-add-flow-offload-for-mt7623.patch
- 601-PCI-mediatek-Use-regmap-to-get-shared-pcie-cfg-base.patch
- 610-pcie-mediatek-fix-clearing-interrupt-status.patch
- 700-net-ethernet-mtk_eth_soc-add-support-for-coherent-DM.patch
- 710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
It still requires fixing PCIe support:
[ 6.644699] pcie_iproc_bcma bcma0:7: host bridge /axi@18000000/pcie@12000 ranges:
[ 6.652217] pcie_iproc_bcma bcma0:7: No bus range found for /axi@18000000/pcie@12000, using [bus 00-ff]
[ 6.661833] OF: /axi@18000000/pcie@12000: Missing device_type
[ 6.667622] pcie_iproc_bcma: probe of bcma0:7 failed with error -12
[ 6.673985] pcie_iproc_bcma bcma0:8: host bridge /axi@18000000/pcie@13000 ranges:
[ 6.681514] pcie_iproc_bcma bcma0:8: No bus range found for /axi@18000000/pcie@13000, using [bus 00-ff]
[ 6.691137] pcie_iproc_bcma: probe of bcma0:8 failed with error -12
[ 6.697522] pcie_iproc_bcma bcma0:9: host bridge /axi@18000000/pcie@14000 ranges:
[ 6.705048] pcie_iproc_bcma bcma0:9: No bus range found for /axi@18000000/pcie@14000, using [bus 00-ff]
[ 6.714669] pcie_iproc_bcma: probe of bcma0:9 failed with error -12
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The label-mac logic relies on the mac-address property of a netdev
devices of-node. However, the mac address can also be stored as a
different property or read from e.g. an mtd device.
Create this node when reading a mac-address from OF if it does not
already exist and copy the mac-address used for the device to this
property. This way, the MAC address can be accessed using procfs.
Signed-off-by: David Bauer <mail@david-bauer.net>
The LEDs for LAN1 and LAN3 were swapped. Link on port 1 would illuminate
the LED on port 3 and vice versa.
Signed-off-by: David Bauer <mail@david-bauer.net>
Without explicit configuration of these pins the ethernet as well as
status LED of the device do not work correctly.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit b309248730.
This commit could create a property without allocated memory, breaking
subsequent reads over a nodes property. Also, the mac-address-increment
was not applied when reading from nvmem.
Revert this commit for now, which breaks the label-mac-address logic.
Possibly, traversing the device-tree from the netdev side is easier
anyways.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
* QCA9531, 16 MiB flash (Winbond W25Q128JVSQ), 128 MiB RAM
* 802.11n 2T2R (external antennas)
* QCA9887, 802.11ac 1T1R (connected with diplexer to one of the antennas)
* 3x 10/100 LAN, 1x 10/100 WAN
* UART header with pinout printed on PCB
Installation:
* The device comes with a bootloader installed only
* The bootloader offers DHCP and is reachable at http://10.123.123.1
* Accept the agreement and flash sysupgrade.bin
* Use Firefox if flashing does not work
TFTP recovery with static IP:
* Rename sysupgrade.bin to jt-or750i_firmware.bin
* Offer it via TFTP server at 192.168.0.66
* Keep the reset button pressed for 4 seconds after connecting power
TFTP recovery with dynamic IP:
* Rename sysupgrade.bin to jt-or750i_firmware.bin
* Offer it via TFTP server with a DHCP server running at the same address
* Keep the reset button pressed for 6 seconds after connecting power
Co-authored-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
This patch did not apply cleanly any more after support for the XTX
flash was added to the generic patches.
Fixes: 92012dd867 ("kernel: Add support for XTX XT26G02A SPI NAND")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch has been carried since introduction throughout every kernel
major bump and no one has tested if the later kernels improved the
situation. The Armada 3720 SoC can only process GbE interrupts on Core 0
and this is already limited in all stable kernels, so ditch this
workaround for 64 bit SoCs.
Ref: https://git.kernel.org/torvalds/c/cf9bf871280d
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Enable the Microsemi phy driver to support the VSC8514 QSGMII phy on the
FRWY-LS1046A board.
Otherwise, the "Generic PHY" driver is used.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
commit 2c2d77bd3b ("layerscape: add FRWY-LS1046A board support")
missed to add an entry to the 79_move_config preinit script.
Therefore, the config transfer on sysupgrade wass broken for this device.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This reverts commit b7ee0786b5.
With the previous commit "realtek: remove rtl83xx vlan 1 special cases"
this is no longer required.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
On reset, the PVID of all ports is set to 1; if this is reset to 0,
the special cases for VLAN 1 are no longer required.
port_vlan_add is called with vid=0 when the DSA port interfaces are
enabled with no VLAN; previously the VLAN was not configured in this
case, relying on VLAN 1 being present, but with the PVID set to 0,
configuring VLAN 0 as normal works as expected.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Add CONFIG_HAVE_ARM_ARCH_TIMER (disabled). A make kernel_oldconfig on cortexa9
will otherwise prompt for its selection. The 5.4 configuration already contains
the same symbol.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add the new CONFIG_BATTERY_RT5033 to the generic configuration, as reported by
Paul Blazejowski. Resort the kconfig while at it.
No deleted or manually refreshed patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Adds support for GPON SFP modules based on the Realtek RTL8672 and
RTL9601C chips, including but not limited to:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
Signed-off-by: Vladimir Markovets <abam_a@yahoo.com>
Latest binutils (2.37) exposed a long-standing bug. The kernel linking stage
would break at the SORTTAB step, due to the exception table having been
previously purged from vmlinux, as its section wasn't marked as unconditionally
kept. Fix thusly.
Additionally, the "#define ARM_MMU_DISCARD(x) KEEP(x)" change is bogus. It
would only apply to !CONFIG_MMU devices (which we don't support in OpenWrt), and
it would even break the build if referenced. Drop it.
While at it, rename the patch in order to make it obvious that it's
arm-specific.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Add same changes for kernel 5.4 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch fixes the fifo rx mode for the mt7623. It is already accepted
upstream for Linux Kernel 5.15.
To test the spi we can change the dts file to
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins_a>;
status = "okay";
spidev: spidev@0 {
compatible = "linux,spidev";
spi-max-frequency = <1000000>;
reg = <0>;
};
};
Afterwards we should see a spidev device under /dev/.
To test it we can further use spidev-test.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nvmem require the device node to be registered with the of_platform.
Register the device node so that nvmem can correctly find the dev and
correctly load the mac-addr stored in the nvmem cell declared in the dts.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
A missing quote in target/linux/ath79/patches-5.x/920-mikrotik-rb4xx.patch
produces:
...
scripts/kconfig/conf --syncconfig Kconfig
drivers/mfd/Kconfig:2016:warning: multi-line strings not supported
...
This patch adds missing closing quote, fixing the above warning.
Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
Traversing the device-tree by referencing a network device to determine
a devices labe-mac does not work with the generic nvmem implementation,
as the userspace expects the MAC-address to be available as a
device-tree property.
The legacy mtd-mac-address implementation did create such a node. Do the
same when using the nvmem implementation to allow reading the MAC
address.
Fixes commit d284e6ef0f ("treewide: convert mtd-mac-address-increment*
to generic implementation")
Signed-off-by: David Bauer <mail@david-bauer.net>
The image generation code for the U7623 board expects ext4 filesystem
to be selected in menuconfig and CONFIG_TARGET_ROOTFS_PARTSIZE to be
defined. Now that ext4 isn't enabled any more, the variable was missing
and broke the build.
Set the default (104) instead of using the config variable to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MAC address retrieval was switched to more generic upstream (5.13) NVMEM
based solution in commit 06bb4a5018 ("ramips: convert mtd-mac-address
to nvmem implementation") , but NVMEM subsystem wasn't enabled in the
kernel, so fix it now.
References: https://github.com/openwrt/openwrt/pull/4041#issuecomment-883322801
Fixes: 06bb4a5018 ("ramips: convert mtd-mac-address to nvmem implementation")
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message]
MAC address retrieval was switched to more generic upstream (5.13) NVMEM
based solution in commit 32adbfc789 ("bmips: convert mtd-mac-address
to nvmem implementation"), but NVMEM subsystem wasn't enabled in the
kernel, so fix it now.
References: https://github.com/openwrt/openwrt/pull/4041#issuecomment-883322801
Fixes: 32adbfc789 ("bmips: convert mtd-mac-address to nvmem implementation")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
When reworking the BPi-R2 the mtk-mmc-img build step was removed
despite it was still needed to build the image for the UniElec U7623
board. Add it back for now until U7623 gets its facelift.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A full read-write rootfs cannot work inside uImage.FIT as the hash
will obviously change once writing to it. Disable generating ext4
rootfs images.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* introduce recovery (=initramfs) vs. production dual boot scheme
* make use of uImage.FIT (instead of FAT partition)
* generate images using build steps (instead of external scripts)
* simplify sysupgrade and config restore (thanks to uImage.FIT)
* make sure mmc devices are ordered persistently (set DT aliases)
This commit breaks sysupgrade from existing installations, you will
have to re-install using the sdcard.img.gz image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Introduce new partition type 0x2e representing uImage.FIT and trigger
FIT partition parser on partitions having that type.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware flow offloading was reported to work when setting the right
version identifier. Import a patch from Frank Wunderlich doing that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update Kernel config and set Linux 5.10 for mediatek/mt7623.
(patches have already been updated to 5.10 when mt7622 was bumped)
Tested on Bananapi BPi-R2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As x86/64 and x86/generic may be using UEFI, mounting the FAT-32 /boot
is necessary in order not to loose configuration files accross
sysupgrades. Include kmod-fs-vfat by default to make sure /boot can
always be mounted.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.
This should make simplify the conversion of target to nvmem implementation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
NR_CPUS limits the number of CPUs supported to 8. This makes total sense
on hardware-restircted platforms, but not on x86_64, where CPUs with
more than 8 cores can be easily acquired and with less physical limitaions.
see also: https://forum.openwrt.org/t/x86-64-8-cpu-limitation-on-vanilla-release/100946
Signed-off-by: Edgar Su <sjs333@outlook.com>
When compiling with all modules enabled, Kconfig complains about
CONFIG_I2C_DESIGNWARE_SLAVE being unset. Disable this symbol by default.
Fixes commit e9c9b5ec72 ("kernel: package Synopsys Designware PCI to I2C controller")
Signed-off-by: David Bauer <mail@david-bauer.net>
When the AVM FRITZ!Repeater 1200 was introduced on Kernel 4.19, the
at803x PHY driver incorrectly set up the delays, not disabling delays
set by the bootloader.
The PHY was always operating with RX as well as TX delays enabled, but
with kernel 5.4 and later, the required TX delay is disabled, breaking
ethernet operation.
Correct the PHY mode, so the driver enables both delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
Commands in 10_fix_wifi_mac were not properly concatenated, so
this was also triggered for the second phy without giving a
MAC address as argument.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: MT7621AT
* RAM: 256MB
* Flash: 128MB NAND flash
* WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC
* LAN: 5x1000M
* Firmware layout is Uboot with extra 96 bytes in header
* Base PCB is DIR-1360 REV1.0
* LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue,
USB Blue
* Buttons Reset,WPS, Wifi
MAC addresses on OEM firmware:
lan factory 0xe000 f4:*:*:a8:*:65 (label)
wan factory 0xe006 f4:*:*:a8:*:68
2.4 GHz [not on flash] f6:*:*:c8:*:66
5.0 GHz factory 0x4 f4:*:*:a8:*:66
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
f4:XX:XX:a8:XX:66 f6:XX:XX:c8:XX:66 +0x20
x0:xx:xx:68:xx:xx x2:xx:xx:48:xx:xx -0x20
x4:xx:xx:6a:xx:xx x6:xx:xx:4a:xx:xx -0x20
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Flashing instruction:
The Dlink "Emergency Room" cannot be accessed through the reset
button on this device. You can either use console or use the
encrypted factory image availble in the openwrt forum.
Once the encrypted image is flashed throuh the stock Dlink web
interface, the sysupgrade images can be used.
Header pins needs to be soldered near the WPS and Wifi buttons.
The layout for the pins is (VCC,RX,TX,GND). No need to connect the VCC.
the settings are:
Bps/Par/Bits : 57600 8N1
Hardware Flow Control : No
Software Flow Control : No
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device
At the time of adding support the wireless config needs to be set up by
editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LUCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Signed-off-by: Karim Dehouche <karimdplay@gmail.com>
[rebase, improve MAC table, update wireless config comment, fix
2.4g macaddr setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Tom Wizetek (@wizetek) for testing.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
The mx25l25635f supports clock speed up to 50Mhz.
Also remove obsolete "mx25l25635f" hack and rename
the matching device-tree flash node.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[mention node rename as well. chip is very very likely
always the "f" revision for all NBG6617]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This PR adds support for router D-Link DIR-853-R1
Specifications:
SoC: MT7621AT
RAM: 128MB
Flash: 16MB SPI
WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC (This mode allows this
single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time)
LAN: 5x1000M
LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue
USB Blue
Buttons Reset,WPS, Wifi
MAC addresses:
|Interface | MAC | Factory |Comment
|------------|-----------------|-------------|----------------
|WAN sticker |C4:XX:XX:6E:XX:2A| |Sticker
|LAN |C4:XX:XX:6E:XX:2B| |
|Wifi (5g) |C4:XX:XX:6E:XX:2C|0x4 |
|Wifi (2.4g) |C6:XX:XX:7E:XX:2C| |
| | | |
| |C4:XX:XX:6E:XX:2E|0x8004 0xe000|
| |C4:XX:XX:6E:XX:2F|0xe006 |
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C4:XX:XX:6E:XX:2C C6:XX:XX:7E:XX:2C 0x10
f4:XX:XX:16:XX:32 f6:XX:XX:36:XX:32 0x20
F4:XX:XX:A6:XX:E3 F6:XX:XX:B6:XX:E3 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Flashing instruction:
The Dlink "Emergency Room"
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Then, power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device.
Signed-off-by: Stas Fiduchi <fiduchi@protonmail.com>
[commit title/message improvements, use correct label MAC address,
calculate MAC addresses based on 0x4, minor DTS style fixes, add
uart2 to state_default, remove factory image, add 2.4g MAC address,
use partition DTSI, add macaddr comment in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Looks like the symbol was forgotten for 5.4
Fixes: 820e660cd7 ("ath79: add NAND driver for MikroTik RB91xG series")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The MX25L12805D used on all ath79 OCEDO boards supports clock
speeds up to 50 MHz.
Thus, we can increase the maximum SPI frequency the flash chip is
controlled at to 50 MHz, increasing transfer speed.
Signed-off-by: David Bauer <mail@david-bauer.net>
The M25P80 used on the Siemens WS-AP3610 supports clock speeds up to 54
MHz. Thus, we can safely increase the maximum SPI frequency the flash
chip is controlled at to 50 MHz, increasing transfer speed.
Signed-off-by: David Bauer <mail@david-bauer.net>
The minew g1-c is a smart home gateway / BLE gateway.
A Nordic nRF52832 is available via USB UART (cp210x) to support BLE.
The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported).
There is a small LED which is only visible when the device is open which
will be used as LED until the ws2812b is supported.
The board has also a micro sdcard/tfcard slot (untested).
The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST).
The vendor uses an older OpenWrt version, sysupgrade can be used via
serial or ssh.
CPU: MT7628AN / 580MHz
RAM: DDR2 128 MiB RAM
Flash: SPI NOR 16 MiB W25Q128
Ethernet: 1x 100 mbit (Port 0) (PoE in)
USB: USB hub, 2x external, 1x internal to USB UART
Power: via micro usb or PoE 802.11af
UART: 3.3V, 115200 8n1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Device specifications
* SoC: QCA9563 @ 775MHz (MIPS 74Kc)
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (EN25QH128)
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9988): a/n/ac, 4x4 MU-MIMO
* IoT Wireless 2.4GHz (QCA6006): currently unusable
* Ethernet (AR8327): 3 LAN × 1GbE, 1 WAN × 1GbE
* LEDs: Internet (blue/orange), System (blue/orange)
* Buttons: Reset
* UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
* Power: 12VDC, 1,5A
MAC addresses map (like in OEM firmware)
art@0x0 88:C3:97:*:57 wan/label
art@0x1002 88:C3:97:*:2D lan/wlan2g
art@0x5006 88:C3:97:*:2C wlan5g
Obtain SSH Access
1. Download and flash the firmware version 1.3.8 (China).
2. Login to the router web interface and get the value of `stok=` from the
URL
3. Open a new tab and go to the following URL (replace <STOK> with the stok
value gained above; line breaks are only for easier handling, please put
together all four lines into a single URL without any spaces):
http://192.168.31.1/cgi-bin/luci/;stok=<STOK>/api/misystem/set_config_iotdev
?bssid=any&user_id=any&ssid=-h%0Anvram%20set%20ssh_en%3D1%0Anvram%20commit
%0Ased%20-i%20%27s%2Fchannel%3D.%2A%2Fchannel%3D%5C%5C%22debug%5C%5C%22%2F
g%27%20%2Fetc%2Finit.d%2Fdropbear%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A
4. Wait 30-60 seconds (this is the time required to generate keys for the
SSH server on the router).
Create Full Backup
1. Obtain SSH Access.
2. Create backup of all flash (on router):
dd if=/dev/mtd0 of=/tmp/ALL.backup
3. Copy backup to PC (on PC):
scp root@192.168.31.1:/tmp/ALL.backup ./
Tip: backup of the original firmware, taken three times, increases the
chances of recovery :)
Calculate The Password
* Locally using shell (replace "12345/E0QM98765" with your router's serial
number):
On Linux
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5sum - | head -c8 && echo
On macOS
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5 | head -c8
* Locally using python script (replace "12345/E0QM98765" with your
router's serial number):
wget https://raw.githubusercontent.com/eisaev/ax3600-files/master/scripts/calc_passwd.py
python3.7 -c 'from calc_passwd import calc_passwd; print(calc_passwd("12345/E0QM98765"))'
* Online
https://www.oxygen7.cn/miwifi/
Debricking (lite)
If you have a healthy bootloader, you can use recovery via TFTP using
programs like TinyPXE on Windows or dnsmasq on Linux. To switch the router
to TFTP recovery mode, hold down the reset button, connect the power
supply, and release the button after about 10 seconds. The router must be
connected directly to the PC via the LAN port.
Debricking
You will need a full dump of your flash, a CH341 programmer, and a clip
for in-circuit programming.
Install OpenWRT
1. Obtain SSH Access.
2. Create script (on router):
echo '#!/bin/sh' > /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo '. /bin/boardupgrade.sh' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo 'board_prepare_upgrade' >> /tmp/flash_fw.sh
echo 'mtd erase rootfs_data' >> /tmp/flash_fw.sh
echo 'mtd write /tmp/openwrt.bin firmware' >> /tmp/flash_fw.sh
echo 'sleep 3' >> /tmp/flash_fw.sh
echo 'reboot' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
chmod +x /tmp/flash_fw.sh
3. Copy `openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin`
to the router (on PC):
scp openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin \
root@192.168.31.1:/tmp/openwrt.bin
4. Flash OpenWRT (on router):
/bin/ash /tmp/flash_fw.sh &
5. SSH connection will be interrupted - this is normal.
6. Wait for the indicator to turn blue.
Signed-off-by: Evgeniy Isaev <isaev.evgeniy@gmail.com>
[improve commit message formatting slightly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SOC: Qualcomm Atheros TP9343 (750 MHz)
Flash: 8 Mb (GigaDevice GD25Q64CSIG)
RAM: 64 Mb (Zentel A3R12E40DBF-8E)
Serial: yes, 4-pin header
Wlan: Qualcomm Atheros TP9343, antenna: MIM0 3x3:3 RP-SMA
3 x 2.4GHz power amp module Skyworks (SiGe) SE2576L
Ethernet: Qualcomm Atheros TP9343
Lan speed: 100M ports: 4
Lan speed: 100M ports: 1
Other info: same case, ram and flash that TP-Link TL-WR841HP,
different SOC
https://forum.openwrt.org/t/adding-device-support-tp-link-wr941hp/
Label MAC addresses based on vendor firmware:
LAN *:ee label
WAN *:ef label +1
WLAN *:ee label
The label MAC address found in "config" partition at 0x8
Flash instruction:
Upload the generated factory firmware on web interface.
Signed-off-by: Diogenes Rengo <rengocbx250@gmail.com>
[remove various whitespace issues, squash commits, use short 0x0]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the Ubiquiti PowerBeam M (XW), e.g. PBE-M5-400,
a 802.11n wireless with a feed+dish form factor. This device was previously
supported by the ar71xx loco-m-xw firmware.
Specifications:
- Atheros AR9342 SoC
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in
- Power and LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1)
Flashing via stock GUI:
- Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see
https://openwrt.org/toh/ubiquiti/powerbeam installation instructions)
- Upload the factory image via AirOS web GUI.
Flashing via TFTP:
- Use a pointy tool (e.g., unbent paperclip) to keep the
reset button pressed.
- Power on the device (keep reset button pressed).
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button.
- The device starts a TFTP server at 192.168.1.20.
- Set a static IP on the computer (e.g., 192.168.1.21/24).
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbeam-m-xw-squashfs-factory.bin
WARNING: so far, no non-destructive method has been discovered for
opening the enclosure to reach the serial console. Internal photos
are available here: https://fcc.io/SWX-NBM5HP
Signed-off-by: Russell Senior <russell@personaltelco.net>
The ar71xx GPIO driver only uses 0x24 registers, all following GPIO
registers are using to control pinmux functions, which are not handles
by the GPIO driver but the generic Linux pinctrl driver.
For some SoC conflicting address ranges were defined for these (AR7240 &
AR9330).
Resolve these cases and align the address space of the GPIO controller
between all SoCs, as the used address space of the driver is identical
for all these.
Signed-off-by: David Bauer <mail@david-bauer.net>
Analysis done by Denis Kalashnikov:
It seems that some ROS versions on some routerboard models have this bug:
after silence boot (no output to uart, no beeps) beeper clicks when wireless traffic is.
https://forum.mikrotik.com/viewtopic.php?f=3&t=92269https://forum.mikrotik.com/viewtopic.php?t=63399
From these links:
1)
Hello, I have RB951G-2HnD and I noticed strange thing
when I loaded the device with some wireless traffic it
produced strange sound - like hissing, fizzing etc.
2)
Same problem still on 6.33, with silent boot enabled
I hear buzzing noise on wireless load.
3)
The sound is fixed in v5.19, it was a bug that caused beeper to make clicks.
It also got fixed in RouterOS:
* What's new in 5.19 (2012-Jul-16 10:51):
fix ticking sound on RB411UAHL;
* What's new in 6.38.3 (2017-Feb-07 09:52):
rb3011 - fixed noise from buzzer after silent boot;
I've checked with an oscilloscope that:
* When on the ssr beeper pin is 0,
on the beeper itself is 1 (~5V),
and when on the ssr beeper pin is 1,
on the beeper is 0
The beeper doesn't consume power,
so 1 should be a default/idle value for the ssr beeper pin).
* When there is wireless traffic (ping packets)
in the background and the beeper clicks, I see
pulses on the beeper itself,
but no pulses on the ssr beeper pin (Q5 pin of 74hc595).
When I manually toggle the ssr beeper pin I see pulses on both.
So, it is likely that the phantom beeper clicks are caused by the EMI.
Suggested-by: Denis Kalashnikov <denis281089@gmail.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
When the ltq_deu_vr9 kernel module is loaded, hostapd does not start any
more. It fails with this error message:
daemon.err hostapd: nl80211: kernel reports: key addition failed
daemon.err hostapd: Interface initialization failed
OpenWrt uses the standard Linux crypto API in the wifi drivers now
and this probably makes the system offload more crypto operations to
special hardware like the Lantiq DEU. There is probably a bug in the DEU
and these operations fail and then hostapd does not start the interface.
Do not include the Lantiq DEU by default any more.
Fixes: FS#3901
Fixes: 53b6783907 ("mac80211: remove patches stripping down crypto support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Notupus <notpp46@gmail.com>
2 small fix for the dedicated cpufreq driver:
- Fix index wrongly used as the current cpu
- Exit early if a bad freq is detected. In the current state the freq
is applied anyway even with invalid state.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
With the new implementation of the dedicated cpufreq driver,
the 1.4 Ghz was only dropped and not added to the ipq8065 SoC.
Fix this to improve performance.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The new cpufreq dedicated driver changed the node structure
on how the cache should be defined in the dts. The 5.4 dtsi addition
patch has not been updated to follow the new implementation.
Fix this to restore correct cache scaling and restore any performance
regression.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This commit adds support for the Teltonika RUT230 v1, a Atheros AR9331
based router with a Quectel UC20 UMTS modem.
Hardware
--------
Atheros AR9331
16 MB SPI-NOR XTX XT25F128B
64M DDR2 memory
Atheros AR9331 1T1R 802.11bgn Wireless
Boootloader: pepe2k U-Boot mod
Hardware-Revision
-----------------
There are two board revisions of the RUT230, a v0 and v1.
A HW version is silkscreened on the top of the PCBs front side as well
as shown in the Teltonika UI. However, this looks to be a different
identifier, as the GPl dump shows this silkscreened / UI shown version
are internally treated identically.
Th following mapping has been obtained from the latest GPl dump.
HW Ver 01 - 04 --> v0
HW Ver > 05 --> v1
My board was a HW Ver 09 and is treated as a v1.
Installation
------------
While attaching power, hold down the reset button and release it after
the signal LEDs flashed 3 times.
Attach your Computer with the devices LAN port and assign yourself the
IPv4 address 192.168.1.10/24. Open a web browser, navigate to
192.168.1.1. Upload the OpenWrt factory image.
The device will install OpenWrt and automatically reboots afterwards.
You can use the smae procedure with the stock firmware to return back to
the vendor firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
The beeper is currently not fully functional and has also
been removed from DTS.
Also remove the dependency for the gpio-beeper module.
Fixes: 695a1cd53c ("ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* With kernel 5.4.128, ran: make kernel_menuconfig CONFIG_TARGET=generic
* Manually added back CONFIG_LEDS_TRIGGER_DISK=y so as not to revert
f93fcf8923 ("ipq806x: enable disk-activity LED trigger")
Signed-off-by: John Audia <graysky@archlinux.us>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Though not strictly necessary, add the closing symbol to make the
job easier for future developers editing this file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
MediaTek MT7621 SoC
256M DDR3
16MB BoHong SPI-NOR
MediaTek MT7905+7975 2x2T2R DBDC bgnax / acax
RGB LED
WPS + RESET Button
UART on compute module (silkscreened / 115200n8)
The router itself is just a board with Power / USB / RJ-45 connectors
and DC/DC converters. The SoC and WiFi components are on a
daughterboard which connect using two M.2 connectors.
The compute module has the model number "T-CB1800K-DM2 V02" printed on
it. The main baord has "T-MB5EU V01" printed on it. This information
might be useful, as it's highly likely either of these two will be
reused in similar designs.
The router itself is sold as Tenbay T-MB5EU directly from the OEM as
well as "KuWFI AX1800 Smart WiFi 6 Eouter" on Amazon.de for ~50€ in a
slightly different case.
Installation
------------
A Tool for creating a factory image for the Vendor Web Interface can be
found here: https://github.com/blocktrron/t-mb5eu-v01-factory-creator/
As the OEM Firmware is just a modified LEDE 17.01, you can also access
failsafe mode via UART while the OS boots, by connecting to UART
and pressing "f" when prompted. The Router is reachable at
192.168.1.1 via root without password.
Transfer the OpenWrt sysupgrade image via scp and apply with sysupgrade
using the -n and -F flags.
Alternatively, the board can be flashed by attaching to the UART
console, interrupting the boot process by keeping "0" pressed while
attaching power.
Serve the OpenWrt initramfs using a TFTP server with address
192.168.1.66. Rename the initramfs to ax1800.bin.
Attach your TFTP server to one of the LAN ports. Execute the following
commands.
$ setenv ipaddr 192.168.1.67
$ setenv serverip 192.168.1.66
$ tftpboot 0x84000000 ax1800.bin
$ bootm
Wait for the device to boot. Then transfer the OpenWrt sysupgrade image
to the device using SCP and apply sysupgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds a driver for the AW9523 I2C GPIO expander.
This driver is required to make LEDs as well as buttons on the Tenbay
T-MB5EU-V01 work.
This driver already had several upstream iterations. I'm working to
push this driver to mainline.
Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287
Signed-off-by: David Bauer <mail@david-bauer.net>
It was reported AR8033 did not work in fiber operation mode on the ER-X.
While the earlier attempt of fixing this mitigated the issue of 1000
Base-X link mode not being supported, it also switched to the copper
page, breaking fiber operation altogether.
Extend the hack adding fiber operation so it does not switch to the
copper page. Also remove the part where the supported link mode bit for
1000 Base-X is removed, as this is required for fiber operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
AR8031/AR8033 have different status registers for copper
and fiber operation. However, the extended status register
is the same for both operation modes.
As a result of that, ESTATUS_1000_XFULL is set to 1 even when
operating in copper TP mode.
Remove this mode from the supported link modes, as this driver
currently only supports copper operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
Enable the XRX200 PMAC, GSWIP DSA tag and GSIP DSA drivers in the 5.4
kernel config. Update the existing vr9_*.dts{,i} to use the new
Ethernet and switch drivers. Drop the swconfig package from the xrx200
target because swconfig doesn't manage DSA based switches.
The new /etc/config/network format for the DSA driver is not compatible
with the old (swconfig) based one. Show a message during sysupgrade
notifying users about this change and asking them to start with a fresh
config (or forcefully update and then migrate the config manually).
Failsafe mode can now automatically bring up the first lan interface
based on board.json including DSA based setups. Drop
05_set_preinit_iface_lantiq from the xRX200 sub-target as this is not
needed anymore. For now we are keeping it for the ase, xway and
xway_legacy until there's some confirmation that it can be dropped from
there as well.
While here, some boards also receive minor fixups:
- Use LAN1 as LAN1 (according to a photo this port can also be
configured as WAN) on the Buffalo WBMR-300HPD. This makes it easier to
read the port mapping because otherwise we would have LAN{2,3,4} and
WAN (which was the case for the non-DSA version previously).
- vr9_avm_fritz3390.dts: move the "gpio" comment from port 0 and 1 to
their corresponding PHYs
- vr9_tplink_vr200.dtsi: move the "gpio" comment from port 0 to PHY 0
- vr9_tplink_tdw89x0.dtsi: move the "gpio" comment from port 0 to PHY 0
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Tested-by: Notupus <notpp46@googlemail.com> # TD-W9980/DM200/FRITZ 7430
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TDT VR2020
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TP-Link TD-W8980B
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on ZyXEL P-2812HNU-F1
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 7490
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 3490
Tested-by: @jospezial <jospezial@gmx.de> # tested on VGV7510KW22 (o2 Box 6431)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Manually rebased:
bcm27xx/patches-5.4/950-0089-cgroup-Disable-cgroup-memory-by-default.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
Ensure the esw is initialized before the ethernet device is sending
packets. Further implement carrier detection similar to mt7620.
If any port has a link, the ethernet device will detect a carrier.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
For rt3050 the switch needs to be initialized before the ethernet start sending
packets. Allow switch_init to return -EPROBE_DEFER.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The dts defines the reset fe for all architectures. However
the soc code used direct register access of the reset controller.
Replace the custom soc reset with a generic fe_reset_fe().
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The fe_reset function direct access the reset controller instead
using the reset controller api. In preparation to use the
reset controller.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
In the new kernel version 5.X,reboot will fail.
When SOC is reset, flash has not exited the 4-byte address mode,
which causes the operation mode mismatch of flash during boot.Add
broken-flash-reset to make flash exit 4-byte address mode before
SOC reset
Signed-off-by: Liu Yu <f78fk@live.com>
Without this definition ethernet led can work as usual, but it's better to
re-add it. Relying on default values may cause uncontrollable factors.
Fixes: 882a6116d3 ("ramips: improve pinctrl for Youku YK-L1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
These boards have AR8327 or QCA8337 external ethernet switch.
The SOC also has it's own internal switch
where VLAN is now enabled by default.
Changes to preinit caused all switches to have VLANs enabled by default
even if they are not configured with a topology in uci_defaults
(see commit f017f617ae)
When both internal and external switches have VLANs,
and the external switch has both LAN and WAN,
the TX traffic from the SOC cannot flow to the tagged port on the external switch
because the VLAN IDs are not matching.
So disable the internal switch VLANs by default on these boards.
Also, add a topology for the internal switch,
so that on LuCI there is not an "unknown topology" warning.
In theory, it may be possible to have LAN ports on both switches
through internal and external PHYs, but there are no known boards that have this.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Define and use some missing macros,
and use them instead of BIT() or numbers for more readable code.
Add comment for a bit change that seems unrelated to ethernet
but is actually needed (PCIe Root Complex mode).
Remove unknown and unused macro RST_CTRL_MCM
(probably from MT7621 / MT7622)
This is the last of a series of fixes, so bump version.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
the register bits for TX delay and RX delay are opposites:
when TX delay bit is set, delay is enabled
when RX delay bit is set, delay is disabled
So, when both bits are unset, it is RX delay
and when both bits are set, it is TX delay
Note: TXID is the default RGMII mode of the SOC
Fixes: 5410a8e295 ("ramips: mt7620: add rgmii delays support")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Add back the register write to disable internal PHYs
as a separate option in the code that can be set using a DTS property.
Set the option to true by default
when an external mt7530 switch is identified.
This makes the driver more in sync with original SDK code
while keeping the lines separated into different options
to accommodate any board with any PHY layout.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The function mt7620_mdio_mode is only called once
and both the function and mdio_mode block have been named incorrectly,
leading to confusion and useless commits.
These lines in the mdio_mode block of mt7620_hw_init
are only intended for boards with an external mt7530 switch.
(see commit 194ca6127e)
Therefore, move lines from mdio_mode to the place in soc_mt7620.c
where the type of mt7530 switch is identified,
and move lines from mt7620_mdio_mode to a main function.
mt7620_mdio_mode was called from mt7620_gsw_init
where the priv struct is available,
so the lines must stay in mt7620_gsw_init function.
In order to keep things as simple as possible,
keep the DTS property related function calls together,
by moving them from mt7620_gsw_probe to init.
Remove the now useless DTS properties and extra phy nodes.
Fixes: 5a6229a93d ("ramips: remove superfluous & confusing DT binding")
Fixes: b85fe43ec8 ("ramips: mt7620: add force use of mdio-mode")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Set the PHY base address to 12 for mt7530 and 8 for others,
which is based on the default setting for some devices
from printing the register with the following command
after it is written to by uboot during the boot cycle.
`md 0x10117014 1`
PHY_BASE option only uses 5 bits of the register,
bits 16 to 20, so use 8-bit integer type.
Set the option using the DTS property mediatek,ephy-base
and create the gsw node if missing.
Also, added a kernel message to display the EPHY base address.
Note:
If anything is written to a PHY address that is greater than 1 hex char (greater than 0xf)
then there is adverse effects with Atheros switches.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
When the new variable ephy_base was introduced,
it was not applied to the if block for mdio_mode.
The first line in the mdio_mode if block
sets the EPHY base address to 12 in the SOC by writing a register,
but the corresponding variable in the driver
was still set to the default of 0.
This causes subsequent lines that write registers with the function
_mt7620_mii_write
to write to PHY addresses 0 through 4
while internal PHYs have been moved to addresses 12 through 16.
All of these lines are intended only for PHYs on the SOC internal switch,
however, they are being written to external ethernet switches
if they exist at those PHY addresses 0 through 4.
This causes some ethernet ports to be broken on boards with AR8327 or QCA8337 switch.
Other suggested fixes move those lines to the else block of mdio_mode,
but removing the else block completely also fixes it.
Therefore, move the lines to the mt7620_hw_init function main block,
and have only one instance of the function mtk_switch_w32
for writing the register with the EPHY base address.
In theory, this also allows for boards that have both external switches
and internal PHYs that lead to ethernet ports to be supported.
Fixes: 391df37829 ("ramips: mt7620: add EPHY base mdio address changing possibility")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
A workaround was added to the switch driver
to set SOC port 4 as an RGMII GMAC interface
based on the DTS property mediatek,port4-gmac.
(previously mediatek,port4)
However, the ethernet driver already does this,
but is being blocked by a return statement
whenever the phy-handle and fixed-link properties
are both missing from nodes that define the port properties.
Revert the workaround, so that both the switch driver
and ethernet driver are not doing the same thing
and move the phy-handle related lines down
so nothing is ending the function prematurely.
While at it, clean up kernel messages
and delete useless return statements.
Fixes: f6d81e2fa1 ("mt7620: gsw: make IntPHY and ExtPHY share mdio addr 4 possible")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
These nodes are used for configuring a GMAC interface
and for defining external PHYs to be accessed with MDIO.
None of this is possible on MT7620N, only MT7620A,
so remove them from all MT7620N DTS.
When the mdio-bus node is missing, the driver returns -NODEV
which causes the internal switch to not initialize.
Replace that return so that everything works without the DTS node.
Also, an extra kernel message to indicate for all error conditions
that mdio-bus is disabled.
Fixes: d482356322 ("ramips: mt7620n: add mdio node and disable port4 by default")
Fixes: aa5014dd1a ("ramips: mt7620n: enable port 4 as EPHY by default")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
There are only 2 options in the driver
for the function of mt7620 internal switch port 4:
EPHY mode (RJ-45, internal PHY)
GMAC mode (RGMII, external PHY)
Let the DTS property be boolean instead of string
where EPHY mode is the default.
Fix how the properties are written
for all DTS that use them,
and add missing nodes where applicable,
and remove useless nodes,
and minor DTS formatting.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The RTL8380-RTL9300 switches only forward packets when VLAN ID 1 is
configured. Do not use the standard failsafe configuration for DSA
accessing the default port directly, but configure a switch on the lan1
interface instead.
This will add the VLAN ID 1 configuration to the switch:
$ bridge vlan show
port vlan-id
lan1 1 PVID Egress Untagged
switch 1 PVID Egress Untagged
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without this patch we have to manually bring up the CPU interface in
failsafe mode.
This was backported from kernel 5.12.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
These are the latest patches that just landed upstream for 5.13, will be
backported by Greg into 5.10 (because of stable@), and are now in the
5.4 backport branch of wireguard: https://git.zx2c4.com/wireguard-linux/log/?h=backport-5.4.y
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Fixes the buffer and packet length calculations for Ethernet TX on
the RTL8380 SoC when CRC calculation offload is enabled.
CRC-offload is always done by the SoC, but additional CRC
calculation was previously done also by the kernel.
It also fixes detection of the DSA tag for packets on RTL8390
SoCs for ports > 28.
v2 has correct whitespace
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Currently, the option to disable subpage writing is only set
when a HW ECC engine is used.
Some boards lack a HW ECC engine and use software for that.
In this case, this NAND option does not get set when the NAND chip
does not support it, resulting in mounting errors.
Move the setting of this option to a generic init location so it
gets set for all types where required.
While at it, also OR the option instead of just setting it
so we don't overwrite potential flags being set somewhere else.
Before:
[ 1.681273] UBI: auto-attach mtd2
[ 1.684669] ubi0: attaching mtd2
[ 1.688877] ubi0 error: validate_ec_hdr: bad VID header offset 2048, expected 512
[ 1.696469] ubi0 error: validate_ec_hdr: bad EC header
[ 1.701712] Erase counter header dump:
[ 1.705512] magic 0x55424923
[ 1.709322] version 1
[ 1.712330] ec 1
[ 1.715331] vid_hdr_offset 2048
[ 1.718610] data_offset 4096
[ 1.721880] image_seq 1462320675
[ 1.725680] hdr_crc 0x12255a15
After:
1.680917] UBI: auto-attach mtd2
[ 1.684308] ubi0: attaching mtd2
[ 2.954504] random: crng init done
[ 3.142813] ubi0: scanning is finished
[ 3.163455] ubi0: attached mtd2 (name "ubi", size 124 MiB)
[ 3.169069] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.176037] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.182942] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.190013] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0
[ 3.196102] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 3.203434] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1462320675
[ 3.212700] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20
[ 3.222124] ubi0: background thread "ubi_bgt0d" started, PID 317
[ 3.230246] block ubiblock0_1: created from ubi0:1(rootfs)
[ 3.235819] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 3.256830] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This board has been supported in the ar71xx.
Links:
* https://mikrotik.com/product/RB912UAG-2HPnD
* https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb912uag-2hpnd
This also supports the 5GHz flavour of the board.
Hardware:
* SoC: Atheros AR9342,
* RAM: DDR 64MB,
* SPI NOR: 64KB,
* NAND: 128MB,
* Ethernet: x1 10/100/1000 port with passive POE in,
* Wi-Fi: 802.11 b/g/n,
* PCIe,
* USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A
port -- both can be used for LTE modem, but only one can be
used at any time.
* LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED,
Ethernet phy LED,
* Button,
* Beeper.
Not working:
* Button: it shares gpio line 15 with NAND ALE and NAND IO7,
and current drivers doesn't easily support this configuration,
* Beeper: it is connected to bit 5 of a serial shift register
(tested with sysfs led trigger timer). But kmod-gpio-beeper
doesn't work -- we left this as is for now.
Flashing:
* Use the RouterBOARD Reset button to enable TFTP netboot,
boot kernel and initramfs and then perform sysupgrade.
* From ar71xx OpenWrt firmware run:
$ sysupgrade -F /tmp/<sysupgrade.bin>
For more info see: https://openwrt.org/toh/mikrotik/common.
Co-Developed-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Main part is copied from ar71xx original driver rb91x_nand
written by Gabor Juhos <juhosg@openwrt.org>.
What is done:
* Support of kernel 5.4 and 5.10,
* DTS support,
* New gpio API (gpiod_*) support.
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
This is a slighty modified version of ar71xx gpio-latch driver
written by Gabor Juhos <juhosg@openwrt.org>.
Changes:
* DTS support,
* New gpio API (gpiod_*).
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
All bcm4908 devices are expected to have GPIO buttons to make relevant
package selected by default.
This "fixes" triggering failsafe mode.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* only add factory.bin when it's defined
* fix check-size vs. append-metadata
* whitespace/line break cleanup
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Remove micro-DTSI mt7621_dlink_dir-882-x1.dtsi to ease reading
config without too much inheritance
* Use "separate" partitioning DTSIs so we can use the partitioning
without a complete match on the other settings (i.e. without the
former parent DTSI)
* Rename files to express the new organization
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The option was added in 5.9 and for some reason, it is causing performance
issues at least on an APU2 board with the igb device.
Switch CONFIG_PCIE_BUS_DEFAULT to fix the performance issues and match the
older kernel's behavior
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reduces the flash space impact, since built-in code is much smaller
than a bunch of kernel modules on squashfs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch failed to apply, breaking builds for the ramips target.
Fixes commit c44cefceb3 ("generic: kernel 5.4: fix probe error for AR803x PHYs")
Signed-off-by: David Bauer <mail@david-bauer.net>
Recent filtering rules alow to trim the kernel configuration in size, do
that to reduce the diff between current config and upcoming one.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Specifications:
- QCA9533 SoC, 8 MB nor flash, 64 MB DDR2 RAM
- 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps
- 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100
- 1x WAN, LAN, Wifi, PWR, WPS, RE Leds
- Reset, Wifi on/off, WPS, RE buttons
- Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1
Label MAC addresses based on vendor firmware:
LAN *:ea label
WAN *:eb label +1
2.4 GHz *:ea label
The label MAC address in found in u-boot 0x1fc00
Installation:
Upload openwrt-ath79-generic-tplink_tl-wr841hp-v3-squashfs-factory.bin
from stock firmware webgui.
Maybe we need rename to shorten file name due to stock webgui error.
Revert back to stock firmware instructions:
- set your PC to static IP address 192.168.0.66 netmask 255.255.255.0
- download stock firmware from Tp-link website
- put it in the root directory of tftp server software
- rename it to wr841hpv3_tp_recovery.bin
- power on while pressing Reset button until any Led is lighting up
- wait for the router to reboot. done
Forum support topic:
https://forum.openwrt.org/t/support-for-tp-link-tl-wr841hp-v3-router
Signed-off-by: Andy Lee <congquynh284@yahoo.com>
[rebase and squash]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves CONFIG_REGULATOR to the target config instead of the
subtarget config.
For kernel 5.10, CONFIG_AT803X_PHY depends on CONFIG_REGULATOR.
As we do not have a size constraint, move this symbol to the
target configuration for kernel 5.4 as well as 5.10.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
Atheros PHYs using the at803x driver apart from the AR8031/AR8033 fail
to probe with kernel 5.4, due to ret in at803x_probe being
uninitialized.
[ 1.403461] Atheros 8035 ethernet: probe of 4ef600c00.ethernet:01
failed with error -1066114012
Initialize ret in order to successfully prove the PHYs on kernel 5.4.
Kernel 5.10 is not affected, as the ret is always assigned prior to
returning.
Tested on OCEDO Koala.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
The patch adds support for the TP-Link Archer C6 v3 (FCC ID TE7A6V3)
The patch adds identification changes to the existing TP-Link Archer A6,
by Vinay Patil <post2vinay@gmail.com>, which has identical hardware.
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-c6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated by powercycling the router four times
before the boot process is complete.
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Signed-off-by: Amish Vishwakarma <vishwakarma.amish@gmail.com>
[fix indent]
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
RockChip RK3399 ARM64 (6 cores)
4GB LPDDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
2x USB 3.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
=====================================
NOTICE FOR USERS WHO USE 1GB VERSION:
BY NOW IT IS NOT SUPPORTED
====================================
[initialed target]
Co-developed-by: Marty Jones <mj8263788@gmail.com>
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[fixed bootscript]
Co-developed-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Similar to how this is done in the diag.sh found in the base-files
package, we should blink our status LED (if we have one) during the
upgrade process. This follows the same blink pattern as seen at
./package/base-files/files/etc/diag.sh#L36
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The default trigger for the amber lights on lan1 and lan3 were
mistakenly swapped after the device's migration to DSA. This
caused activity on one port to trigger the amber light on the
other port. Swapping their default trigger in the DTS file
fixes that.
Signed-off-by: Adam Elyas <adamelyas@outlook.com>
[minor commit title adjustment, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
At this moment kernel size in mt7620 snapshot builds is bigger than 2048k.
It should be disabled by default.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Since few months multiple users reported problems with various JBoot
devices. [0][1][2][3] All of them was bricked.
On my Lava LR-25G001 it freezes with current snapshot:
CDW57CAM_003 Jboot B695
Giga Switch AR8327 init
AR8327/AR8337 id ==> 0x1302
JRecovery Version R1.2 2014/04/01 18:25
SPI FLASH: MX25l12805d 16M
.
.
(freeze)
The kernel size is >2048k.
I built current master with minimal config and it boots well:
CDW57CAM_003 Jboot B695
Giga Switch AR8327 init
AR8327/AR8337 id ==> 0x1302
JRecovery Version R1.2 2014/04/01 18:25
SPI FLASH: MX25l12805d 16M
.
...........................
Starting kernel @80000000...
[ 0.000000] Linux version 5.4.124
Kernel size is <2048k.
Jboot bootloader isn't open source, so it's impossible to find
solution in code. It looks, that some buffer for kernel have 2MB size.
To avoid bricked devices, this commit introduces 2048k limit kernel
size for all jboot routers.
[0] https://bugs.openwrt.org/index.php?do=details&task_id=3539
[1] https://eko.one.pl/forum/viewtopic.php?pid=254344
[2] https://eko.one.pl/forum/viewtopic.php?id=20930
[3] https://eko.one.pl/forum/viewtopic.php?pid=241376#p241376
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[remove Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Set the ethernet address from flash.
MAC addresses as verified by OEM firmware:
use interface source
2g wlan0 factory 0x04 (label)
LAN eth0.1 factory 0x28 (label+1)
WAN eth0.2 factory 0x2e (label+2)
Fixes: 671c9d16e3 ("ramips: add support for HILINK HLK-7628N")
Signed-off-by: Liu Yu <f78fk@live.com>
[drop old MAC address setup from 02_network, cut out state_default
changes, face-lift commit message, add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The patch for adding the config_aneg function for the Atheros
AR8031/AR8033 PHY was formatted in a way it moved to different PHY
models while refreshing patches on kernel updates.
Move the diff directly below the PHY name so this won't happen in the
future.
Signed-off-by: David Bauer <mail@david-bauer.net>
This enables autonegotiation for all ephy ports on probe.
Some devices do not configure the ports, particularly port 4.
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[replace magic values ; reword commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
The basic mode control register of the ESW PHYs is modified in this
codeblock. Use the respective macros to make this code more readable.
Signed-off-by: David Bauer <mail@david-bauer.net>
As patches for the AR8031/AR8033 copper page selection were merged
upstream, we can backport these patches.
This also fixes a PHY capabilities detection issue on the Ubiquiti
ER-X-SFP.
Signed-off-by: David Bauer <mail@david-bauer.net>
