Fix also some Chinese GB18030 -> UTF-8 encoding problems
(translated the Chinese strings to English):
修改 -> modification
port8~port10的设置在另外一个register ->
port8~port10 setup is done in a separate register
You are in the correct (UTF-8) encoding when you see:
* $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
e.g. week 3, 08 third month, 2017
But not if you see:
* $Date: 2017-03-08 15:13:58 +0800 (閫变笁, 08 涓夋湀 2017) $
rtl8367c/rtl8367c_asicdrv_lut.c should be read as UTF-8, despite having
some earlier Chinese text lost to GB18030 encoding.
Improves indexing and searches
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input
Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Airoha EN8801SC PHY is a gigabit PHY used on Edgecore EAP111 so, include
the MTK driver with some cleanups.
Unfortunatelly, there is no specification sheet nor datasheet available
in order to demistify the magic PBUS writes and work on upstreaming
this driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 3 buttons (WPS, reset, LED on/off)
- 1 1Gbit WAN port
- 4 1Gbit LAN ports
Disassembly:
- There are four screws at the bottom: 2 under the rubber feets, 2 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes on the side of the board.
- Pins (from front to rear):
- 3.3V
- RX
- TX
- GND
- Settings: 115200, 8N1
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- The recovery web interface always flashes to the currently active partition.
- If OpenWrt is flahsed to the second partition, it will not boot.
- Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end.
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-recovery.bin
- The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt.
- If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are reuqired:
- Start the web recovery interface again and flash the **decrypted OEM image**. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1.
- Now flash the **encrypted OEM image** via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1.
- Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-initramfs-kernel.bin.
- Power on the device and select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.200.2, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M30 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware M30A1_FW101B05: ./m32-firmware-util M30 --DecryptFactoryImage M30A1_FW101B05\(0725091522\).bin M30A1_FW101B05\(0725091522\)_decrypted.bin
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Controlling the LEDs:
- The LEDs are controlled by a chip called "GCA230718" which is connected to the main CPU via I2C (address 0x40)
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Comparison to M32/R32:
- The algorithms for decrypting the OEM firmware are the same for M30/M32/R32, only the keys differ
- The keys are available in the GPL sources for the M32
- The M32/R32 contained raw data in the firmware images (kernel, rootfs), the R30 uses a sysupgrade tar instead
- Creation of the recovery image is quite similar, only the header start string changes. So mostly takeover from M32/R32 for that.
- Turned out that the bytes at offset 0x0E and 0x0F in the recovery image header are the checksum over the data area
- This checksum was not checked in the recovery web interface of M32/R32 devices, but is now active in R30
- I adapted the recovery image creation to also calculate the checksum over the data area
- The recovery image header for M30 contains addresses which don't match the memory layout in the DTS. The same addresses are also present in the OEM images
- The recovery web interface either calculates the correct addresses from it or has it's own logic to determine where which information must be written
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
The recovery image is reqired for D-Link M30 as well. So I moved it to include/image-commands.mk to be able to use it for MT7622 and filogic devices.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: W632GU6NB DDR3 256MB
Ethernet: 1x 2.5G + 4x 1G
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
1. Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
2. Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-preloader.bin spi0.0"
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
3. Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download initramfs image, reboot router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Note:
1. Back up all mtd partitions before flashing.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 8GB eMMC or 128 MB SPI-NAND
RAM: 256MB
Ethernet: 5x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
USB: M.2(B-key) for 4G/5G Module
Power: DC 12V 1A
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC RX TX GND | <= |
| ----------------- |
--------------------------
The U-boot menu will automatically appear at startup, and then select
the required options through UP/DOWN Key.
NAND Flash and eMMC Flash instructions:
1. Set your computers IP adress to 192.168.1.2.
2. Run a TFTP server providing the sysupgrade.bin image.
3. Power on the router, into the U-Boot menu.
4. Select "2. Upgrade firmware"
5. Update sysupgrade.bin file name, input server IP and input device
IP (if they deviate from the defaults)
6. Wait for automatic startup after burning
Signed-off-by: Allen Zhao <allenzhao@unielecinc.com>
When building MT7629 with ALL_KMODS then we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot compilation.
It depends on I2C so the symbol is hidden until ALL_KMODS is used and I2C
support is available, so disable the LEDS_SMARTRG_LED symbol in 6.6 config
intentionally as is done in the 6.1 mt7629 config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The vendor u-boot knows nothing about UBI, and we used to have a
fixed-size kernel partition for vendor u-boot and UBI for rootfs.
However, that fixed partition becomes too small eventually, and
expanding it requires complicated procedure.
This commit changed the flash layout and added a second u-boot
where the kernel supposed to be.
Now the vendor u-boot chainloads our mainline u-boot, and our
u-boot reads kernel+rootfs from UBI, verifies it, and boot
into OpenWrt.
There are two possible ways to convert from the old fw:
Flash the factory image using mtd (provided by @rany2):
mount -o remount,ro /
mount -o remount,ro /overlay
cd /tmp
dd if=factory.bin bs=1M count=4 | mtd write - kernel
dd if=factory.bin bs=1M skip=4 | mtd -r write - ubi
Or, flash the 2nd u-boot via mtd and upload the firmware
to the 2nd u-boot using tftp:
1. prepare a tftp server at 192.168.1.254 to serve the
sysupgrade image:
openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-squashfs-sysupgrade.itb
2. upload the ubi-loader.itb to OpenWrt /tmp, and flash it to
the old kernel partition:
mtd -r write openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-ubi-loader.itb
3. The router should reboot and flash the sysupgrade image via TFTP.
Procedure for flashing from vendor firmware shouldn't change.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Most mt7622 devices use the mt7531 switch, which have been
switched to dsa driver for a long time. So use dsa as the
default configuration and configure these rtl8367s devices
separately. This reduces the amount of code.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
In kernel 6.6, dts files for mediatek arm target are moved into
arch/arm/boot/dts/mediatek instead of legacy path arch/arm/boot/dts.
To avoid dts compile failure, change DTS_DIR to the mediatek subfolder
for kernel 6.6.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Add missing CLK_TOP_PEXTP_Px_SEL clock for each of the 4 PCIe interfaces
of the MT7988 SoC. Without that clock PCIe doesn't work reliable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The GL.iNet X3000 and XE3000 are Wi-Fi 6 5G cellular routers, based on
MediaTek MT7981A SoC. The XE3000 is the same device as the X3000,
except for an additional battery.
Specifications:
- SoC: Filogic 820 MT7981A (1.3GHz)
- RAM: DDR4 512M
- Flash: eMMC 8G, MicroSD card slot
- WiFi: 2.4GHz and 5GHz with 6 antennas
- Ethernet:
- 1x LAN (10/100/1000M)
- 1x WAN (10/100/1000/2500M)
- 5G: Quectel RM520N-GL with two nano-SIM card slots
- USB: 1x USB 2.0 port
- UART:
- 3.3V, TX, RX, GND / 115200 8N1
MAC addresses as verified by OEM firmware:
vendor OpenWrt address source
WAN eth0 label factory 0x0a (label)
LAN eth1 label + 1
2g phy0-ap0 label + 2 factory 0x04
5g phy1-ap0 label + 3
Installation via U-Boot rescue:
1. Press and hold reset button while booting the device
2. Wait for the Internet led to blink 5 times
3. Release reset button
4. The rescue page is accessible via http://192.168.1.1
5. Select the OpenWrt sysupgrade image and start upgrade
6. Wait for the router to flash new firmware and reboot
Revert to stock firmware:
1. Download the stock firmware from GL.iNet website
2. Use the method explained above to flash the stock firmware
Switch the modem network port between PCIe and USB interfaces:
1. Connect to the AT commands (/dev/ttyUSB2) port using
e.g. minicom: minicom -D /dev/ttyUSB2
2. Check the current modem mode with 'AT+QCFG="data_interface"':
- 0,0 indicates that the network port uses the USB interface
- 1,0 indicates that the network port uses the PCIe interface
3. Switch the active interface with:
- 'AT+QCFG="data_interface",0,0' to use the USB interface
- 'AT+QCFG="data_interface",1,0' to use the PCIe interface
4. Reboot
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Add new emmc groups in the pinctrl driver for the
MediaTek MT7981 SoC:
* emmc reset, with pin 15.
* emmc 4-bit bus-width, with pins 16 to 19, and 24 to 25.
* emmc 8-bit bus-width, with pins 16 to 25.
The existing emmc_45 group is kept for legacy reasons, even
if this is the union of emmc_reset and emmc_8 groups.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
As shared remove functions now returns void instead of int we need to
use .remove_new instead of .remove.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Due to what seems to be an undocumented oddity in MediaTek's MT7988
SoC design the CLK_INFRA_PCIE_PERI_26M_CK_P2 clock requires
CLK_INFRA_PCIE_PERI_26M_CK_P3 to be enabled.
This currently leads to PCIe port 2 not working in Linux.
Reflect the apparent relationship in the clk driver to make sure PCIe
port 2 of the MT7988 SoC works.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Include a statement about having to run the installer in the
sysupgrade compat warning for the Linksys E8450 (UBI).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Probing of the fitblk driver in some situations happens after the kernel
attempts to mount rootfs, which then fails.
Always use 'rootwait' when using fitblk for rootfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit 2d63d42f5e ("mediatek: convert to new LED color/function
format where possible") leaves Xiaomi Redmi AX6000 un-converted,
the two LEDs become dead.
Now, LEDs are alive again.
Fixes: 2d63d42f5e ("mediatek: convert to new LED color/function
format where possible")
Signed-off-by: Furong Xu <xfr@outlook.com>
Use type casts to prevent compiler warnings which are going to turn
into errors when we switch to Linux 6.6.
In the long run we should try to get rid of this downstream driver
now that RTL8367S is support by the rtl8365mb DSA driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rename kernel patches accepted upstream to indicate at which version
they have been accepted, replacing downstream variants which what was
accepted upstream. Note that some of them are fixes which will
find their way to older kernel versions as well via linux-stable.
No functional changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some backported thermal patches ended up with the wrong kernel
version in their filename. Fix this.
Fixes: c36de2e73a ("mediatek: backport a hell of thermal commits")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MT7981B /256MB /16MB SPI (XM25QH128C)
AX 2.4Ghz
AX 5Ghz 160Mhz wide
1Gbit LAN
OEM:
root@RE3000:~# ifconfig |grep HWaddr
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0
rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0
rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0
OpenWrt
root@OpenWrt:/# ifconfig |grep HW
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1
tftp Installation via u-boot:
Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin
write to flash via sysupgrade or gui
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
The boot loader does not have a fixed size limit for the kernel,
so we're free to change the layout. This may break sysupgrade, but a fresh
flash from initramfs works.
Fixes: 6e2962d4c5 ("mediatek: mt7622: skip build for MT7622 rfb1 (UBI)")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If selected on a per-board base, fitblk doesn't end up in initramfs
images which always only come with the subtarget's default packages.
Hence fitblk needs to be included as a default package of all
subtargets making use of fitblk instead of it being selected for
individual boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we got fitblk_get_bootdev in /lib/upgrade/common.sh we don't
need platform_get_bootdev in each of the subtargets any longer.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The device booting successfully indicates that bootloader has been
updated. Set compat_version to 1.1 on new configs and bump
compat_version to 1.1 on first boot after a successful sysupgrade.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set root=/dev/fit0 cmdline parameter as the kernel won't mount rootfs
otherwise after the change from the FIT partition parser to the fitblk
driver which replaces it.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623.
Introduce boot device selection for fitblk's /chosen/rootdisk
handle, similar to how it is already done on MT7622, MT7986 and MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All mt7622 board previously using the FIT partition parser have been
converted to use the fitblk driver:
6aec3c7b5b mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build
41c053141e mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblk
208f6c1232 mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblk
Remove the now no longer needed FIT partition parser from builds for
mt7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix style of nvmem cell names in the device tree of the GL.iNet MT-2500.
Fixes: 49ed52b862 ("mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMC)"
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch to make sure SGM_REG_SEL clock is always enabled as it
seems that more registers than just SGMIISYS0 and SGMIISYS1 are
depending on that clock being enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we can reference MMC partitions in device tree, use that
to get rid of Wi-Fi EEPROM and MAC address setup in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove inaccurate compatible string 'mediatek,mt7986-ethsys' which
results in the wrong clock driver probing on MT7981 with Linux 6.1 and
ends up freezing the system once WED is used.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by
host system. With built-in drivers this doesn't work in OpenWrt /
embeddded as filesystem isn't available during PHY probe. That results
in delays like:
[ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld
[ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110)
Switch to module to postpone PHY probe to init state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Also here build fails due to increased kernel size.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Due to increased kernel size the build currently fails if including
the MT7622 rfb1 (UBI). Skip it for now until there is a better
solution (such as replacing the bootloader and changing the flash
layout).
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Include the needed Ethernet PHY driver module for the BananaPi R3 mini.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Reported-by: BPI forum user nezar_taima
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
One of the pins requiered by M.2 slot is conflict with spi1,
however, spi1 seems unused so simply disable it for now, this
matches the factory behavior [1].
1. 9bd78779f2
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Conversion to new LED color/function format and drop label format.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property can be
removed in favor of the new format.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Generate ubinized image as ARTIFACT and make use of now available
generic 'ubinize-image' build step intended for that purpose.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix NAND flash layout which was out-of-sync with the definition in
ARM TrustedFirmware-A which expects UBI to start at 0x200000.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification
----------------------
SoC: MediaTek MT7986A 4x A53
Flash: 128MB SPI-NAND, 8GB eMMC
RAM: 2GB DDR4
Ethernet: 2x 2.5GbE (Airoha EN8811H)
WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
Interfaces:
* M.2 Key-M: PCIe 2.0 x2 for NVMe SSD
* M.2 Key-B: USB 3.0 with SIM slot
* front USB 2.0 port
LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
Button: Reset, internal boot switch
Fan: PWM-controlled 5V fan
Power: 12V Type-C PD
Installation instructions for eMMC
----------------------------------
0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt
running there).
1. Write GPT partition table to eMMC
Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to
the device /tmp using scp and write it to /dev/mmcblk0:
dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0
2. Reboot (to reload partition table)
3. Write bootloader and OpenWrt images
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate partitions:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5
sync
4. Remove the device from power, set boot switch to eMMC and boot into
OpenWrt. The device will come up with IP 192.168.1.1 and assume the
Ethernet port closer to the USB-C power connector as LAN port.
5. If you like to have Ethernet support inside U-Boot (eg. to boot via
TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1:
echo 0 > /sys/block/mmcblk0boot1/force_ro
dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1
dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1
Installation instructions for NAND
----------------------------------
0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there
by instructions above. Using stock rom or immortalwrt does NOT work!)
1. Write things to NAND
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate locations:
mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0
ubidetach -m 1
ubiformat /dev/mtd1
ubiattach -m 1
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip)
ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static
ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
cd /lib/firmware/airoha
cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static
ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976
ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
3. Remove the device from power, set boot switch to NAND, power up and
boot into OpenWrt.
Partially based on immortalwrt support for the R3 mini, big thanks for
doing the ground work!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add PHY driver for Airoha EN8811H PHY and package it as kernel module.
The PHY needs to load firmware from rootfs, so there is no point in
having the driver built-into the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Firmware for the built-in 2.5G Ethernet PHY of the MediaTek MT7988 SoC
is now part of linux-firmware, so we can package it.
Only a single file is needed with recent driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Switch to all-UBI layout on SPI-NAND
* use fitblk driver instead of uImage.FIT partition parser
* adapt sysupgrade
* bump COMPAT_VERSION
Remove BROKEN mark now that all needed changes are done.
Boards running images generated before this commit will require
full reflash of the bootloader, re-install from SD card is the
easiest way to achieve that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add environment settings for the BananaPi BPI-R4 router board which
can boot from (and store its bootloader environment on) micro SD card,
SPI-NAND and eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SOC: MediaTek MT7988A (4x Cortex-A73)
RAM: 4 GiB DDR4
Flash: 128 MiB Winbond SPI-NAND
MMC: 8 GiB eMMC *or* microSD (cannot be used both)
ETH: 4x 1GE (1x WAN, 3x LAN)
2x SFP+ (10G, 5G, 2.5G, 1G)
USB: on-board USB 3.2 4-port hub
1x USB 3.2 port (type A connector)
1x M.2 for 4G/5G modem
2x mPCIe for additional modems
WiFi: optional MediaTek MT7996 Wi-Fi 7 module
(using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)
Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).
2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.
3. Switch to boot from SPI-NAND and install to eMMC.
Known issues
------------
- The RST button is hard-wired to the SoC reset and can't be read
from software. This can be changed by modifying the board (ie.
moving a 0-ohm resistor). However, in order to maintain compatibility
with the board as it comes from factory the button isn't used by
OpenWrt and the WPS button is used as factory/reset button instead.
- various small things still need to be fixed in DT
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch from MediaTek SDK which allows using the third
PCIe host controller of the MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add UART pinctrl group for using only pins 80 and 81 for uart1.
This is needed on the BPi-R4 as RTS/CTS signals are used for other
on-board functions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace previous patch adding paths and SerDes modes with patch series
pending upstream adding dedicated drivers for XFI T-PHY and USXGMII PCS,
extends LynxI PCS to be a standalone platform driver and as a consequence
makes much less changes to the actual Ethernet driver mtk_eth_soc.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport almost 50 commits from upstream Linux to improve thermal
drivers for MediaTek SoCs and add new LVTS driver for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let's pick a bunch of useful phylink changes which allow us to keep
drivers in sync with mainline Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Similar to supporting nvmem-layouts on MTD devices, also allow referencing
UBI and MMC devices in DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to allow gradually migrating the boards currently using the
uImage.FIT partition (deprecated/rejected) parser to the new fitblk
driver, skip the partition parser code in case the new fitblk driver
(which serves the same purpose) is used.
As an indicator for the use of the new fitblk driver, check if the
/chosen/rootdisk property is present in the Device Tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The partition parser approach has been rejected upstream, it will be
replaced by a small block driver which is the solution suggestion by
upstream maintainers.
As the partition parser has only been used by the mediatek target, as
a first step, move it there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use order described as preferred in DTS Coding Style. Mostly just move
"compatible", "reg", "ranges" and "status" properties.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The NWA50AX Pro only has a eth0 interface for its only ethernet port.
Use this port for preinit.
Fixes non-working network in failsafe mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch to enable PHYLIB_LEDS kconfig dynamically instead of
having to select this config for every target that makes use of PHY LEDs
API.
All affected patch are automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
Backport at803x split patches merged upstream to tidy things up for the
at803x PHY driver.
New Kernel config are introduced hence any user needs to be updated.
Downstream ipq40xx patch require rework to correctly move them to the
qcom specific PHY directory.
All affected patch automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* fix switch ports with modes other than 1000M/Full
* set 32-bit dma_coherent_mask to get PPE to work with 4 GiB of RAM
* sync driver for built-in 1GE PHY with MediaTek SDK sources
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[rmilecki: port to 5.15]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit dcdcfc1511.
This is a firmware for third-party u-boot mod, which should not
be carried here by us.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The WLAN + WED reset sequence relies on being able to receive interrupts from
the card, in order to synchronize individual steps with the firmware.
When WED is stopped, leave interrupts running and rely on the driver turning
off unwanted ones.
WED DMA also needs to be disabled before resetting.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Refresh patches for Linux 6.1 which no longer apply cleanly after
adding patches to fix ethernet rx hang issue on MT7981/MT7986.
Fixes: ede34465de ("mediatek: fix ethernet rx hang issue on MT7981/MT7986")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fine tuning PR: openwrt/openwrt#14355 Ref: 5a82bb909b
("mediatek: GL-MT6000: Add missing LED state definitions")
As the only LED is using white in the stock firmware when the device is
running and blue for the bootloader I suggest following changes:
- Using blue for the BL and preinit+failsafe
- White for normal operation (like the original FW) and sysupgrade
With this changes it's clear by looking to the LED in which operation
mode the device is and a possible BL stuck can be seen easily.
Tested with [GL-MT6000](https://openwrt.org/toh/gl.inet/gl-mt6000).
Signed-off-by: Thomas Schröder <tschroeder_github@outlook.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
The nvmem-cells is deprecated. Also simplify mac address settings.
Fixes: b4086f4 ("mediatek: add support for YunCore AX835")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The mac address of the network port under the switch is
the same as the corresponding gmac by default, so there
is no need to repeat the setting. Compile test only.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Setting/clearing bits on the first byte of the mac address causes collisions
when using multiple SSIDs on both PHYs. Change the allocation to alter the
last byte instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 16MB NOR
RAM: 256MB
Ethernet: 2x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
Power: DC 12V 1A, PoE 802.3af 48V
Flash instructions:
Option #1 - SSH
I was able to SSH into the stock firmware of my device.
1. Attach the router to the network
2. Use scp (-O) to copy the sysupgrade image
3. Connect using SSH and run `sysupgrade -n`
Option #2 - U-Boot
One way to use the bootloader for flashing is using TFTP:
1. Connect to the router using an ethernet cable
2 Spin up a TFTP server serving the sysupgrade file
3. Open the case and attach a UART
4. Attach power to the router and interrupt the countdown by pressing
any key
5. Select option #2 (Upgrade firmware)
6. Enter IP address information and image name
7. Wait patiently
Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Adjust LED names and provide the OpenWrt status indicator aliases
to actually use LEDs by the OpenWrt boot & sysupgrade processes.
* Name both LEDs clearly by the color
* Add the missing OpenWrt LED status indicator aliases and
remove the now unnecessary default status from blue LED
After this commit, the LEDs are used as:
* bootloader, really early Linux boot: blue LED is on
* preinit/failsafe: white LED blinks rapidly
* late boot: white LED blinks slowly
* boot completed, running normally: blue LED is on
* sysupgrade: white LED blinks
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.
Specification:
- MT7622BV SoC with 2.4GHz wifi
- MT7975AN + MT7915AN for 5GHz
- MT7531BE Switch
- 512MB RAM
- 128 MB flash
- 2 LEDs (Status and Internet, both can be either orange or white)
- 2 buttons (WPS and Reset)
Compared to M32, the R32 has the following differences:
- 4 LAN ports instead of 2
- The recory image starts with DLK6E6015001 instaed of DLK6E6010001
- Individual LEDs for power and internet
- MAC address is stored at another offset in the ODM partition
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin
Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin
Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again
There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.
Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
- The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
- The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
- OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Router Asus TUF AX6000 have second MaxLinear GPY211 PHY controller for 2.5Gb LAN port.
The 5'th LAN port have inverted status of the LED.
Based on the commit from main branch 90fbec8 we could set proper status of the LED.
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(based on support for ASUS RT-AX59U by liushiyou006)
SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Upgrade from AsusWRT to OpenWRT using UART
Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.
Connect the PC with TFTP server to the RT-AX59U.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.
Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax59u.bin
$ bootm 0x46000000
Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Upgrade from AsusWRT to OpenWRT using WebUI
Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq
Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file
Wait for OpenWRT to boot (192.168.1.1).
Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command
MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.
: Stock : OpenWrt
WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
WLAN 2g (2) : : CA:xx:xx:0D:xx:D4
WLAN 2g (3) : : CE:xx:xx:0D:xx:D4
WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
WLAN 5g (2) : : CE:xx:xx:1D:xx:D5
WLAN 5g (3) : : C2:xx:xx:1D:xx:D5
WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
WLAN 2g (2) : : 0A:xx:xx:76:xx:BE
WLAN 2g (3) : : 0E:xx:xx:76:xx:BE
WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
WLAN 5g (2) : : 0E:xx:xx:76:xx:BF
WLAN 5g (3) : : 02:xx:xx:76:xx:BF
Signed-off-by: Xavier Franquet <xavier@franquet.es>
Use order described as preferred in DTS Coding Style:
1. Sort bus nodes by unit address
2. Use alpha-numerical order for the rest
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon@gmail.com>
Add support for wireless offload package in default configuration for
-Cudy WR3000
-Confiabits MT7981
For some reason those ware missing. I confirm this work for my Cudy WR3000
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Pick commits adding drivers for audio engine found in MT7986 from
Linux 6.6 as well as follow-up fixes from Linux 6.7.
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import driver for I2C-connected HolTek MCU controlling the RGBW LED
found in Adtran SmartRG devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
