PCK and MCK should really be P=PMIC and M=MEM, which means that they
should effectively be CLK_PMIC and CLK_ARB.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The USXGMII driver in SDK was heavily refactored, some bugs have been
fixed and it has switched to use phylink_pcs. Follow up with changes
in SDK driver and sync our on-top-of-mainline driver with the SDK
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use renamed build step names for all boards which were not handled by
commit c620409d58 ("mediatek: filogic: add uboot build for mt7981")
and now breaking the build.
Fixes: c620409d58 ("mediatek: filogic: add uboot build for mt7981")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT5CC128M16JR-EK 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Flash instructions:
1. Attach UART, boot the stock firmware until
the message about failsafe mode appears.
2. Enter failsafe mode by pressing "f" and "Enter"
3. Type "mount_root", then run
"fw_setenv bootmenu_delay 3"
4. Back up all mtd partitions before flashing.
5. Reboot, U-Boot now presents a menu.
6. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
7. Select "Upgrade ATF BL2", then use this file:
openwrt-mediatek-filogic-qihoo_360t7-preloader.bin
8. Select "Upgrade ATF FIP", then use this file:
openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip
9. Download the initramfs image, and type "reset",
waiting for tftp recovery to complete.
a. After openwrt boots up, perform sysupgrade.
Note:
1. Since NMBM is disabled, we must back up all partitions.
2. Flash instructions is based on commit 28df7f7.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Add reserved memory for pstore/ramoops to device tree used by Linux
as well as U-Boot.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Pick accepted patches from upstream Linux tree instead of having to
maintain our slightly different downstream patches.
Import pending patch fixing I2C on MT7981 by making sure all clocks
are enabled before accessing I2C registers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure sub-images on the SD card are size-checked, allow
generating SD card without squashfs and/or initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This add basic device tree support for mediatek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Richtek RT5190A is used on the MT7988 reference board. Backport and
enable the driver on the filogic subtarget, so we can support cpufreq
on the MT7988 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add driver for the built-in 2.5G Ethernet PHY found in the MT7988 SoC.
To function the PHY also needs firmware files which have not yet been
published via linux-firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update driver for MediaTek's built-in Gigabit Ethernet PHYs which can be
found in the MT7981 and MT7988 SoCs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport commits adding support for the MT7988 built-in switch to the
mt7530 driver.
This change results in the Kconfig symbol NET_DSA_MT7530 to be extended
by NET_DSA_MT7530_MDIO (everything formally covered by NET_DSA_MT7530)
and NET_DSA_MT7530_MMIO (a new driver for the MMIO-connected built-in
switch of the MT7988 SoC).
Select NET_DSA_MT7530_MDIO for all targets previously selecting
NET_DSA_MT7530, with the exception of mediatek/filogic which also
selects NET_DSA_MT7530_MMIO.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to support Ethernet on the MT7988 SoC add support for NETSYS v3
as well as new paths and USXGMII SerDes to the mtk_eth_soc driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds provisional pinctrl driver support for the MediaTek MT7988 SoC.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds clock drivers for the MediaTek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows loading modules with large memory requirements, recently needed
while testing on armvirt/32. Past forum discussions [1] and bug reports [2]
also raised this and the ipq806x target already set it in response [3].
Given this increases kernel image size by only ~1KB, is generally useful on
multi-platform kernels, and enabled by default on upstream arm32 Linux, add
it to the generic config.
The setting has similar utility on arm64, is a requirement for KASLR, and
already enabled on most OpenWrt aarch64 targets, so pull this into the
top-level generic config.
[1]: https://forum.openwrt.org/t/vmap-allocation-for-size-442368-failed-use-vmalloc-size-to-increase-size/34545/7
[2]: https://github.com/openwrt/openwrt/issues/8282
[3]: f81e148eb6 ("ipq806x: update 4.19 kernel config").
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Allow building SD card images without having both initramfs and squashfs
present on the card, just like it has already been done for the mt7622
and filogic subtargets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Use same logic as in append-metadata so build doesn't fail in case of
missing build-key (it was previously failing on the buildbot runners).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Manually adjusted before running quilt due to new location in tree:
backport-5.15/780-v5.16-bus-mhi-pci_generic-Introduce-Sierra-EM919X-support.patch
backport-5.15/781-v6.1-bus-mhi-host-always-print-detected-modem-name.patch
pending-5.15/790-bus-mhi-core-add-SBL-state-callback.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
When adding support for the GL.iNet GL-MT3000 a reference to the
non-existent make_gl_metadata.py script was accidentally added.
Remove it, flashing from vendor firmware also works fine without that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
16MB SPI-NOR (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
[LEDS] VCC-GND-RX-TX [ETH]
Header is located below the heatsink
Case
----
Unscrew the 4 bottom screws. Remove the top of the case by inserting a
small screwdriver into the ventilation holes and lift the top cover.
This works best by beginning near the ETH-ports. The top is clipped on
the front near the LEDs with two plastic clips. The back has a single
clip in the middle. Start at one of the back edges.
MAC-Addresses
-------------
80:AF:CA:00:F9:C6 LAN
80:AF:CA:00:F9:C7 WAN
80:AF:CA:00:F9:C6 W2
82:AF:CA:30:F9:C6 W5
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device. Keep pressing the "0" key to enter the U-Boot
shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.2. Rename the image to "cudy3000.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Note: Cudy does not yet provide a image for disabling their
signature-protection. This has happened in the past. Make sure to check
the wiki for a possible easier installation method.
Signed-off-by: David Bauer <mail@david-bauer.net>
The OF LED configuration patch fails on MT7621, as the necessary headers
were only included for the mediatek subtarget with an additional patch.
Fixes: 242fe8634e ("generic: add hack for MT753x LED configuration")
Signed-off-by: David Bauer <mail@david-bauer.net>
Apply the same LED configuration used by the vendor-firmware for the
GPY211 controlled WAN LED in OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
As we can now configure the switch LED configuration, write the switch
LED configuration values from the vendor firmware to the switch-IC.
Previously, the switch-LEDs did not show any acitvity or link-status
whatsoever.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix following error when building 32bit arm targets with kmod-crypto-sha512
ERROR: module '/home/user/openwrt/build_dir/target-arm_xscale_musl_eabi/linux-kirkwood_generic/linux-5.15.109/arch/arm/crypto/sha512-arm.ko' is missing.
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
Kernel setting CONFIG_IO_URING supports high-performance I/O for file
access and servers, generally for more performant platforms, and adds
~45 KB to kernel sizes. The need for this on less "beefy" devices is
questionable, as is the size cost considering many platforms have kernel
size limits which require tricky repartitioning if outgrown. The size
cost is also large relative to the ~180 KB bump expected between major
OpenWRT kernel releases.
No OpenWrt packages have hard dependencies on this; samba4 and mariadb
can take advantage if available (+KERNEL_IO_URING:liburing) but
otherwise build and work fine.
Since CONFIG_IO_URING is already managed via the KERNEL_IO_URING setting
in Config-kernel.in (default Y), remove it from those target configs
which unconditionally enable it, and update the defaults to enable it
conditionally only on more powerful 64-bit x86 and arm devices. It may
still be manually enabled as needed for high-performance custom builds.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Since CONFIG_DYNAMIC_DEBUG is already managed via the KERNEL_DYNAMIC_DEBUG
setting in Config-kernel.in (default N), remove or disable it in target
configs which unconditionally enable it, along with the related setting
CONFIG_DYNAMIC_DEBUG_CORE. This saves several KB in the kernels for
ipq40xx, ipq806x, filogic, mt7622, qoriq, and sunxi.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The RealTek 2.5G PHY providing the WAN port of the Netgear WAX206 has
previously been hard-coded in the device tree. Now that the PHY can be
probed correctly also via Clause-45 MDIO, use that instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This deactivates the CONFIG_COMPAT kernel option.
With CONFIG_COMPAT the kernel will provide syscall interfaces for arm32
binaries in addition to the interfaces needed for arm64 binaries.
In OpenWrt the complete userspace is compiled for this specific
architecture and support for 32 bit ARM applications is not needed.
This reduces the size and the attack surface for the systems.
On all other targets CONFIG_COMPAT is already deactivated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates the CONFIG_ARM64_SW_TTBR0_PAN option for all arm64
kernels by default.
The CONFIG_ARM64_SW_TTBR0_PAN option prevents the kernel form accessing
user space memory directly. This makes it harder to exploit the kernel.
This is activated by default and was already activate on all other arm64
targets before.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates CONFIG_HARDENED_USERCOPY for the remaining targets. This
adds additional checks in the copy_from_user() and copy_to_user()
functions.
This was not activated for ARCHS38 before because of a bug in the Linux
kernel 5.4 till 5.14, which as fixed and is described here:
https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/15
I do not know why this was deactivated for mt7629 and rockchip.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: ESMT M15T4G16256A 512MB
Ethernet (Max Speed):
XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan
XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
WiFi:
XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R)
XDR6086/XDR6088:
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 4A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
[Add uboot build, fit and sysupgrade support, fix RealTek PHYs]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix the network configuration according to the device tree.
Fixes: 5faff99 ("mediatek: filogic: fix mt7986a ethernet devicetree entries")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
According to SinoVoip up to 3A @ 3.3V are available for both
SFP modules together. Raise energy limit from 1W (default) to 3W,
however, be aware that using modules consuming more than 1W will
require active cooling!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MEMREAD is a new ioctl for MTD character devices that was first included
in Linux 6.1. It allows userspace applications to use the Linux
kernel's OOB autoplacement mechanism while reading data from NAND
devices. The Yafut tool needs this ioctl to do its job.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Now that new pinconf features have been backported sync pinctrl-mt7981
and pinctrl-m7986 with bleeding-edge upstream versions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport new features for MediaTek pinctrl/pinconf drivers from upstream.
This will serve as the base to improve pinconf bias/pull-up/pull-down on
MT7981 and MT7986, and also prepare for upcoming support for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
We need to reset KERNEL_LOADADDR if we use it on a per-device base.
Otherwise the previous value will be kept in case a device doesn't
define KERNEL_LOADADDR and relies on the default.
Move initializing KERNEL_LOADADDR to target/linux/mediatek/image/Makefile,
similar to how it's done also on the ramips target.
This fixes image size related breakage on devices which rely on the
default value of KERNEL_LOADADDR.
While at it use 0x48000000 which is more common than the previous default
0x44000000 for the filogic subtarget.
Fixed: e7c399bee6 ("filogic: add support for ASUS TUF-AX4200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The wireless driver package was incorrectly removed from the TUF-AX4200
device-packages, resulting in images without wireless functionality.
Fixes: d98c4fb8bf ("mediatek: broaden filogic target description")
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
[rework commit description]
Signed-off-by: David Bauer <mail@david-bauer.net>
The filogic subtarget now also supports MT7981 and will in future
also support MT7988. Reflect that in the target description.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Newer MediaTek's SoCs need SPI calibration routines for SPI to work
reliably. Import patches for that from MediaTek's SDK.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to support PWM on the MT7981 SoC.
This patch will also be submitted to upstream Linux soon.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to support I2C on the MT7981 SoC.
This change will also be submitted to upstream Linux soon.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The mxl-gpy driver apparently was built in the assumption that SGMII
auto-negotiation is always switched on at the MAC. This may be true for
few rather recent drivers (why?), but certainly isn't for most drivers
unless 'managed = "in-band-status"' is set in device tree. Add patch to
the mediatek target which reduces mxl-gpy to behave more like an
ordinary PHY driver using out-of-band status.
This allows to use these PHYs without rate-adaptation which seems to be
at least partially broken/racy in some revisions of the PHY and/or
internal PHY firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch allowing to set the MDIO bus clock frequency.
By default the MDIO bus clock runs on 2.5 MHz, allow increasing it
up to 25 MHz.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MT7981 and the upcoming MT7988 have built-in Gigabit Ethernet PHYs.
While they share some design properties with the PHYs present in
MT753x, they do need calibration data from the SoC's efuse.
Add driver to support them. Upstreaming it is planned, but there are
still some ongoing discussions with MediaTek.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport the pinctrl driver for the MT7981 SoC. The driver has also
been submitted upstream and is part of Linux 6.3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport driver for common clocks in MT7981 SoC. The driver has also
been submitted upstream and became part of Linux 6.3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND (Winbond W25N02KV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
MaxLinear GPY211C 2.5 N-Base-T PHY
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.66/24. Rename the image to tufax4200.bin.
2. Connect the TFTP server to the AX4200. Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.66
$ tftpboot 0x46000000 tufax4200.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The LAN port LEDs are driven by the switch but OpenWrt does not
correctly configure the output.
Signed-off-by: David Bauer <mail@david-bauer.net>
The ASUS TUF-AX4200 bootloader adds invalid parameters for the rootfs.
Without overwriting the cmdline, the kernel crashes when trying to
attach the rootfs, as OpenWrt uses a different partition than the vendor
OS.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes issues with legacy boot loaders that don't process reserved memory
regions outside of system RAM
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
* 2.4 GHz: MediaTek MT7622BV
* 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
115200n8
* Power: 12 VDC, 2.5 A
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm
Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
moment. If connected to a multi-gig port the speed has to be manually
set to 1G/full either for the switch port or in OpenWrt. For example
add the following to /etc/rc.local to set it on boot:
/usr/sbin/ethtool -s wan speed 1000 duplex full
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar
* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
Image creation code for this device
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
By specifying the flag "denx,fit" for partition "kernel", the kernel
try to find rootfs in the same partition during boot. Reality is that
the placement of rootfs is precisely determined by the name of another
partition -"ubi".
It was also found that on some device (for example devices with NAND
chips), the "Denx search engine" manages to find roots at the end of
partition "kernel", but such partition doesn't exist and is empty
there.
Fix this by removing the "denx,fit" flag from partition "kernel". With
this change the original behavior of searchif rootfs in partition "ubi"
is restored.
Signed-off-by: Oleg S <remittor@gmail.com>
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.
Fixes: de94587e70 ("mediatek: filogic: don't rely on image preset in flash or sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.
Fixes: d640cbac0e ("mediatek: mt7622: don't rely on existing image for sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This new layout is only bootable with OpenWrt U-Boot. It reuses the
two crash partions and expands the ubi partion to the end of whole flash.
Do not use this layout with stock U-Boot!
Signed-off-by: Furong Xu <xfr@outlook.com>
'cs-gpios = <0>, <0>' is a hack in ath79 to override the incorrectly
specified maximum number of chipselects available in spi-ath79.c.
It's not needed here and must have been copied here by mistake.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.
1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
be helpful for users who may forget to do this before sysupgrade in
the initramfs.
New flash instructions:
1. Gain ssh access. Please refer to:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)
2. Check which system current u-boot is loading from:
COMMAND: `cat /proc/cmdline`
sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
if firmware=1, current system is ubi1
if firmware=0, current system is ubi0
3. Setup nvram and write the firmware:
If the current system is ubi1, please set it up so that the next time
it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
If the current system is ubi, please set it up so that the next time
it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```
4. After rebooting, the system should now boot into the openwrt initramfs.
Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.
For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:
1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```
2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
add DT nodes and default package for the LEDs on Redmi AX6000
Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Without explicitly enabling sel_clk, clk_disable_unused() will disable
it when boot is done, causing CPU hang on SPI1 register access on MT7986.
Explicitly enable sel_clk to make SPI1 functional.
Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
As the referenced MTD partition is only present in the dts, also move
&slot0 down to the dts files.
Fixes: 64e9b62829 ("mediatek: remove redundant flash entry from dtsi")
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Splitting-off the common parts of Ruijie RG-EW3200GX PRO and
reyee AX3200-E5 went wrong because the flash descriptiom was kept
also in the dtsi. Remove it there, as flash definition is added by
both board dts files.
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly
different flash layout, install process is the same.
Specifications:
SoC: MT7622B
RAM: 256MB
Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
Ethernet: 5x1GbE
Switch: MT7531BE
WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
2Keys: Mesh button + Reset button
UART: Marked J19 on board. 3.3v, 115200n1
Power: 12V 2.5A
Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
dd if=/dev/mtd7 of=/tmp/firmware.bin
and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.
Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
mtd write firmware.bin firmware
Signed-off-by: Alex Hansen <mralexh123@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set CONFIG_MT6577_AUXADC=y as otherwise reading temperature of the
thermal-zone doesn't work on MT7623 (it does work fine without this
driver on MT7622 and MT7986).
Fixes: f2ae4e2f8c ("mediatek: clean up platform kernel modules")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use persistent MAC address for the built-in wireless interfaces of the
BPi-R64 and BPi-R3 development boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The mt7623 subtarget supports 2 devices:
* Bananapi BPi-R2 (added in 1f068588ef, 7762c07c88),
* UniElec U7623-02 (added in 4def81f30f).
Both devices support DSA from the beginning, thus
swconfig can be safely disabled.
In the past, the subtarget mt7623 also supported
the mt7623 reference board. This board originally
supported swconfig, and was later converted to DSA
(64175ffb79) and then dropped (1ab81bf02d).
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
- implement multiqueue via qdma hardware shaper to deal with ports with different speeds
- implement hardware DSA untagging
- add NETIF_F_ALL_TSO to reduce unnecessary segmentation
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The patch "210-pinctrl-mediatek-add-support-for-MT7986-SoC.patch" and
"212-clk-mediatek-add-mt7986-clock-support.patch" are upstreamed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The patches "191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch"
and "192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch" are
upstreamed to 5.19.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This subtarget supports 3 devices:
* Bananapi BPi-R3 (added in a96382c1bb),
* MediaTek MTK7986 rfba AP (added in cffc77ae55),
* MediaTek MTK7986 rfbb AP (added in cffc77ae55).
This subtarget supports DSA from the beginning. It looks like CONFIG_SWCONFIG
was copied from another config when the subtarget was created.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
The patch enabling hardware flow offloading support on the MT7623 SoC
has been merged upstream as of Linux 5.13. Remove our local patch which
wrongly got forward-ported and now actually enables hardware flow
offloading for the MT2701 SoC family (unsupported in OpenWrt).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The use of the adc_oe value stored in the efuse has been dropped in
MediaTek's SDK during a recent refactorization of the temperature
calculation formula. Don't ignore this offset value and again include
it in raw-to-deg-celsius calculation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.
Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....
Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC - enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Add dependency to '32k' ADC clock so it is always enabled for thermal
and raw access to ADC values. This allows to remove the patch for the
ADC driver and reduce the patch adding thermal support for MT7986 to
only add the new efuse layout and temperature decoding for V3.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The most common CPU governor in the OpenWRT project is currently ondemand (see
below). Switch mt7622 over to it as well.
Audit the code by running the following and then analyzing the results:
find -name 'config-5.*' -print0 | xargs -0 grep 'CONFIG_CPU_FREQ_DEFAULT_GOV.*=y'
ondemand: 16
performance: 5
schedutil: 5
userspace: 2
Build system: x86_64
Build-tested: ramips/mt7621
Signed-off-by: John Audia <graysky@archlinux.us>
Remove kmod-sdhci-mtk as the mtk-sd driver is built-in anyway for the
relevant subtargets in order to support mounting rootfs from eMMC or
SD card.
Add kmod-iio-mt6577-auxadc to support reading the raw values from the
auxadc unit used as in-SoC thermal sensor. This driver was previously
built-in, but as thermal itself works well without it there is no use
for it in every day use of a device. Build the module to still allow
access to the raw values for those who need it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Don't reply on mapped rootfs partition but rather just take what ever
has been set to the kernel cmdline root= parameter as a hint to decide
which media to install sysupgrade to on the BananaPi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* remove orphaned Kconfig symbol now that CONFIG_IIO is no longer
selected after commit ef8b935c95 ("mediatek: clean up mt7622 kernel config")
* select UBI fast-map feature to decrease boot time and keep the
number of spare blocks required in sync with U-Boot's expectations
(we got fast-map enabled in U-Boot)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch headers and description for pending patch.
Add version tag to patch already merged upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of trying to figure out the actual root device, just use the
kernel 'root' cmdline parameter as a hint to decide which device to
flash to.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use UBI fast map feature to avoid scanning the whole flash on each
boot which takes several seconds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Raising the temperatures for passive and active trips. @VA1DER
proposed at issue 9396 to remove passive trip. This commit relates to
his suggestion.
Without this patch. the CPU will be throttled all the way down to 98MHz
if the temperature rises even a degree above the trip point, and it was
further discovered that if the internal temperature of the device is
above the first trip point temperature when it boots then it will start
in a throttled state and even
$ echo disabled > /sys/class/thermal/thermal_zone0/mode
will have no effect.
The patch increases the passive trip point and active cooling map. The
throttling temperature will then be at 77°C and 82°C, which is still a
low enough temperature for ARM devices to not be in the real danger
zone, and gives some operational headroom.
Signed-off-by: Bruno Umuarama <anonimou_eu@hotmail.com>
* set correct clocks for PWM to work.
* MT7986 PWM does have the 26MHz-clock-select, set that in patch
* drop useless 'passive' trip point in thermal zone
* extend pwm-fan to have 3 active operating points
* set reasonable trip points in thermal zone
* invert pwm-fan operating points and set shorter period to allow
less noisy operation of the PWM fan of the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Setup thermal zone, select pins and enabled drivers for I2C (on 26-pin
GPIO bank) and PWM (1x fan and 1x GPIO bank).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for hardware I2C and PWM units found in the Filogic SoCs
as well as the CPU thermal support.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches from mtk-openwrt-feeds (MTK SDK) to support reading
t-phy settings affecting PCIe as well as USB2 and USB3 from efuse.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
efuse is used to store board-specific settings of some of the in-SoC
peripherals. Add it to device tree, so it gets probed on boot and can
be accessed by other drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow byte-wise access to mtk-efuse as some drivers require that.
Patch imported from mtk-openwrt-feeds (MTK SDK).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds some missing IOMMU related options for x86/64 and moves some
of them to generic for all targets.
On x86 IOMMU_DEFAULT_DMA_LAZY is used by default, on all other platforms
IOMMU_DEFAULT_DMA_STRICT is the default. we just follow the default
kernel configuration here.
Fixes: 8fea4a102c ("x86/64: enable IOMMU support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.
Fix this by using a wildcard that matches all the variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a7 ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a11 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The newly introduced config symbol CONFIG_CMDLINE_OVERRIDE is only set
for mt7629 for now which breaks automated build on all other mediatek
subtargets. Make sure the symbol is configured as 'is not set' for all
remaining subtargets.
Fixes: c27279dc26 ("mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)
Installation:
- Flash recovery image with TFTP recovery
Revert to stock firmware:
- Flash stock firmware with TFTP recovery
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
MT7915 requires an additional antenna for background radar scanning.
Disable this feature in the following devices that do not have a
separate DFS antenna:
linksys,e8450
ruijie,rg-ew3200gx-pro
xiaomi,redmi-router-ax6s
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The RGB LED of the UniFi 6 LR v1 doesn't work when using the Openwrt-
built U-Boot. This is because the vendor loader resets the ledbar
controller while our U-Boot doesn't care.
Add reset-gpio so the ledbar driver in Linux will always reset the
ledbar controller.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The LEDs connected to the MCU are so-called smart LEDs and their signal is
daisy-chained. Because of this, the MCU needs to be told how many LEDs are
connected. It also means the LEDs could be individually controlled, if the MCU
has a command for this.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
During GPIO initialization the pin state flips and triggers a reset of
the ledbar MCU. It needs to be moved through an initialization sequence
before working correctly.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Some versions of the ledbar MCU have a reset pin. It needs to be
correctly initialized or we might keep the MCU in reset state.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Or the comparison against a signed char is always true, because the
literal 0xaa is treated as an unsigned int, to which the signed char is
casted during comparison. 0xaa is above the positive values of a signed
char and negative signed char values result in values larger than 0xaa
when casted to unsigned int.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
The read response is in the i2c_response variable. Also use %hhx format,
because we're dealing with a single char.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
The GPIO used for the RST button is also used for PCIe-CLKREQ signal.
Hence it cannot be used as button signal if PCIe is also used.
Wire up WPS button to serve as KEY_RESTART in Linux and "reset" button
in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The package kmod-btmtkuart is specific for MT7622 and isn't available
for MT7986 (which doesn't have this built-in Bluetooth like MT7622).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The 213 patch is missing filename suffix. Fix it.
Fixes: dabcaac ("mediatek: add mt7986 soc support to the target")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
According to the device tree, the lan ports are
lan0 to lan3, and the wan port is eth1.
Fixes: cffc77a ("mediatek: add filogic subtarget")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Janusz Dziedzic reported a typo introduced by a recent commit. Fix it.
Fixes: 50c892d67b ("mediatek: bpi-r64: make initramfs/recovery optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only include recovery image in SD card image generated for the
BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only include recovery image in SD card image generated for the
BananaPi BPi-R3 if building with CONFIG_TARGET_ROOTFS_INITRAMFS.
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch 921-mt7986-add-mmc-support.patch introduced by commit
dabcaac443 ("mediatek: add mt7986 soc support to the target") has never
been applied in a way that it would have any effect as it actually
created a file target/linux/generic/patches-5.15/... in the kernel tree
and was probably a patch intended to be applied to openwrt.git instead
of being put into kernel patches folder as a file.
As an upstream commit from vanilla Linux also adding support for MT7986
to the mtk-sd driver has already been included we can remove that old
patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The introduction of the new Airoha target has left the tree in an
unfresh state. Refresh patches to improve that situation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A line in platform.sh was accidentally removed when adding support
for the Bananapi BPi-R3.
Re-add it to fix sysupgrade on the MTK7986 rfba AP.
Fixes: a96382c1bb ("mediatek: add support for Bananapi BPi-R3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure the compatible string in DTS matches the now v1/v2
differentiated board name in target/linux/mediatek/image/mt7622.mk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bananapi BPi-R3 is a development router board built around the
MediaTek Filogic 830 (MT7986A) SoC.
The board can boot either from microSD, SPI-NAND, SPI-NOR or eMMC.
Only either SPI-NAND or SPI-NOR can be used at the same time, also only
either microSD or eMMC can be used. The various storage options can be
selected using small SMD switches on the board.
Specs:
* MediaTek MT7986A (Filogic 830) 4x ARM Cortex A53
* 4T4R 2.4G 802.11bgnax (MT7975N)
* 4T4R 5G 802.11anac/ax (MT7975P)
* 2 GB DDR4 RAM
* 8 GB eMMC
* 128 MB SPI-NAND flash
* 32 MB SPI-NOR flash
* on-board MT7531 GbE switch
* 2x SFP+ (1 GbE / 2.5 GbE)
* 5x GbE network port
* miniPCIe slot (only USB 2.0 connected)
* uSIM slot (connected to miniPCIe interface)
* M.2 KEY-E PCIe interface (PCIe x2)
* microSD card interface
* 26 PIN GPIO
Hardware details: https://wiki.banana-pi.org/Banana_Pi_BPI-R3
Working:
* all 4 boot methods incl. installation via U-Boot, sysupgrade, ...
* copper LAN and WAN ports
* SFP1 (connected to gmac1, eth1 in Linux)
* WiFi
* LEDs
* Buttons
* PSTORE/ramoops based dual-boot
Not Working (missing driver features):
* SFP2 (connected to MT7531 switch)
Untested:
* M.2/NGFF slot (PCIe x2)
* mPCIe slot (USB 2.0 + SIM)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport generic phylink validate series and make use of it for
mtk_eth_soc Ethernet driver as well as mt7530 DSA driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Older MT7623 ARMv7 SoC as well as new Filogic platforms come with
inside-secure,safexcel-eip97 units. Enable them in DTS and select the
driver kernel module by default on those platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Initially this covers MT7986 only, but it will later be expanded to cover other
Filogic branded platforms by MediaTek
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It will be supported by the new filogic subtarget
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_INPUT_MISC does not do any changes to the kernel image, it only
shows some extra kernel configuration options.
Activate it on all targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On boot, kernel log complains no vbus supply is found:
`xhci-mtk 1a0c0000.usb: supply vbus not found, using dummy regulator`
so add the dts node entries to solve the issue
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
When building the mediatek/mt7629 target in OpenWrt 22.03 the kernel
does not have a configuration option for CONFIG_CRYPTO_DEV_MEDIATEK. Add
this option to the generic kernel configuration and also add two other
configuration options which are removed when we refresh the mt7629
kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The recent differentiation between v1 and v2 of the UniFi 6 LR added
support for the v2 version which has GPIO-controlled LEDs instead of
using an additional microcontroller to drive an RGB led.
The polarity of the white LED, however, was inverted and the default
states didn't make a lot of sense after all. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix the wps button to prevent wrongly detected recovery procedures.
In the official banana pi r64 git the wps button is set to
GPIO_ACTIVE_LOW and not GPIO_ACTIVE_HIGH.
Import patch to fix on boot unwanted recovery entering:
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- failsafe button wps was pressed -
- failsafe -
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There is not RTC battery connected to the SoC of the UniFi 6 LR board.
Disable the RTC to prevent the system coming up with time set to
2000-01-01 00:00:00 after each reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add targets:
* Ubiquiti UniFi 6 LR v2
* Ubiquiti UniFi 6 LR v2 (U-Boot mod)
This target does not have a RGB led bar like v1 did
Used target/linux/ramips/dts/mt7621_ubnt_unifi.dtsi as inspiration
The white dome LED is default-on, blue will turn on when the system is
in running state
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
based on current ubnt_unifi-6-lr-ubootmod
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
Based on current mt7622-ubnt-unifi-6-lr, this is a preparation for
adding a v2 version of this target
* v1 - with led-bar
* v2 - two simple GPIO connected LEDs (in later commits)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
Remove redundant target-level entries, noting that these settings will be
configured from "Kernel build options" of Kconfig.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[remove from new configs introduced after patch submission]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Disable support for joysticks, micee and tablets. There's no actual
driver selected in kconfig, and including kernel support is just a
waste of space. Besides that, I believe nobody wants these on a router.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Remove patches and configuration for Linux 5.10 which have been left
in the tree despite the target having been switched to Linux 5.15.
Fixes: c283defa88 ("mediatek: switch to 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set CONFIG_SCHED_MC in config-5.15 to have make the scheduler aware
of shared caches.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Last attempt on this has a typo and doen't work.
It seems that this is a common problem occurring on every kernel bump,
so let's enforce arch timer support for mt7623 with a patch instead.
Fixes: 9a22943eb2 ("mediatek: 5.15: re-enable arch timer on MT7623 as well")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
the SPI-NAND driver switch breaks dts compatibility. It's too much work
to backport all ECC framework support to 5.10 so let's switch the target
to 5.15 instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch implements the spi-nand controller driver as an ECC-capable
spi-mem controller to use the upstream SPI-NAND driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
the OOB layout in MTK SNFI uses the 2nd byte, and anything using OOB
will make the block a bad-block in spi-nand driver.
Hack it for now. We need a proper solution upstream.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.
Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.
See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Use ARMv8 Crypto Extensions for AES, ghash and sha256.
This results in a 16 times speed gain in speed for aes-128-ctr, 17x in
aes-128-gcm, and 9 times in sha256.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.
The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.
The other symbols are disabled and should be in the generic config.
This commit also removes these symbols from subtargets.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
This patch moves the patches of parser_trx in mediatek target to
generic/backport-5.10 to use the changes from ramips target and
backport the additional patch of the parser.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
X32 Pro is another product name for it in the Chinese market.
Specifications:
- SoC: MT7622B
- RAM: 256MB
- Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
- Ethernet: 5x1GbE
- Switch: MT7531BE
- WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
- 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
- 2Keys: Mesh button + Reset button
- UART: Marked J19 on board. 3.3v, 115200n1
- Power: 12V 2.5A
MAC addresses as verified by OEM firmware:
use address source
WAN *:F4 ethaddr@product_info
LAN *:F5
5g *:F6
2g *:F7
Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
dd if=/dev/mtd7 of=/tmp/firmware.bin
and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.
Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
mtd write firmware.bin firmware
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Enable support for allocating user space page table entries in high memory [1],
for the targets which support this feature. This saves precious low memory
(permanently mapped, the only type of memory directly accessible by the kernel).
[1] https://www.kernel.org/doc/html/latest/vm/highmem.html
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
fwtool is now always part of the sysupgrade stage2 ramdisk, so drop
the no longer needed RAMFS_COPY_BIN variable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that both, fw_printenv/fw_setenv and fwtool are always present
during stage2 sysupgrade, we no longer need to list them in
RAMFS_COPY_BIN and RAMFS_COPY_DATA in platform.sh.
Drop both variables as they are now unneeded.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Turns out the MT7531 switch IRQ line is connected to GPIO#53 just like
on the BPi-R64, so this seems to be part of the reference design and
will probably apply to most MT7622+MT7531 boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we support link-state-change interrupts, wire up MT7531 IRQ
line which is connected to GPIO#53 according to the schematics [1].
As a result, PHY state no longer needs to be polled on that board.
[1]: https://forum.banana-pi.org/t/bpi-r64-mt7622-schematic-diagram-public/10118
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and
MT7531. Fix some link up/down issues.
The errornous check for the PHY mode which broke things with MT7531
has been removed as suggested by patch
net: phy: mediatek: remove PHY mode check on MT7531
As a result, things are working fine now on MT7622+MT7531 as well.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
This reverts commit 8b4cba53a9.
This broke the mt7530 on Linksys e8450 (mt7622) for me.
[ 1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0
[ 1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1
[ 1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2
[ 1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3
[ 1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL
[ 1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530.
Fix some link up/down issues.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
The two options 'emmc' and 'sdmmc' now became identical lines after
introducing CONFIG_TARGET_ROOTFS_PARTSIZE.
Remove the now useless if-clauses.
Fixes: a40b4d335a ("mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZE")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Append 'earlycon=uart8250,mmio32,0x11004000' to the boot arguments
embedded in device-tree in order to enable early console on the
UniElec U7623 board when using the vendor/stock bootloader.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The legacy image for the UniElec U7623-02 until now included
kmod-ata-ahci-mtk. The MT7623 chip doesn't have that IP and that
board uses a PCIe-connected AHCI controller for the SATA port and
mSATA-pins of the mPCIe socket. Hence include kmod-ata-ahci instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For devboards without a MAC address assigned from factory, store
the random MAC in U-Boot env on first boot to make it persistent.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Users of older OpenWrt versions need sysupgrade using the *emmc.img.gz
file once which will upgrade U-Boot and switch to the new image layout.
Users of the vendor firmware need to first flash the legacy image to
then sunsequently carry out a full-flash upgrade.
Alternatively the board can also be flashed using MediaTek's
proprietary SP Flash Tool.
Configuration as well as persistent MAC address will be lost once at
this point and you will have to redo (or restore) all configuration
manually. To restore the previous persistent MAC address users may set
it manually using
fw_setenv ethaddr 00:11:22:33:44:55
For future upgrades once running OpenWrt past this commit, the usual
*sysupgrade.itb file can be used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Use serial0 instead of serial2 for the only serial port
* Add LED aliases
* Add ethernet0 alias to inherit ethaddr from U-Boot env
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable 'rootfs-part' feature to make the size of the partition of the
production image configurable instead of hard-coding it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Limit bmt remapping range to cover everything up to and including the kernel image,
use the rest of the flash area for ubi.
Fix partition table and sysupgrade support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Preparation for supporting BMT on MT7621. Move source files to the files/
subdirectory in order to simplify maintenance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
CONFIG_ARM_ARCH_TIMER cannot be enabled in the config directly; it is only
selected by CONFIG_HAVE_ARM_ARCH_TIMER. We need to enable the latter in
our config.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 4f1c5b01c1 ("mediatek: mt7623: backport musb, improve HDMI console")
The Unielec U7623 doesn't have a physical power button; I think it's hard
wired so that it turns on automatically when power is applied (unlike the
Banana Pi R2 which is a pain).
So the 'reset on long press of power button' behaviour that we get when
we enable the PMIC keyboard driver is kind of unhelpful. Disable it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 0d3f3323a2 ("mediatek: mt7623: enable more hardware features")
The lowest frequency should be 300MHz, since that is the label
assigned to the OPP in the mt7622.dtsi device tree, while there is one
missing zero in the actual value.
To be clear, the lowest frequency should be 300MHz instead of 30MHz.
As mentioned @dangowrt on the OpenWrt forum there is no benefit in
leaving 30MHz as the lowest frequency.
Signed-off-by: Jip de Beer <gpk6x3591g0l@opayq.com>
Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
To easy future maintainance, replace the local patch with what has been
accepted into net-next and is likely to end up in Linux 5.17.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
To allows Ethernet phys supporting 2500Base-T mode to announce that
speed, enable the corresponding bit in mtk_eth_soc driver.
This should hopefully unlock 2500Base-T speed on the UniFi 6 LR.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upon comment of Russell King ('Oh no, not this "-1 disease" again.')
clean up mdio read and write return type and value in mtk_eth_soc
driver and also use appropriate return values for bus-busy-timeout-
errors in newly added Clause 45 access code.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace recently added patch
701-net-ethernet-mtk_eth_soc-add-support-for-clause-45-mdio.patch
with version sent upstream
701-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-access.patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This change enables proper Ethernet link status and speed reporting on
the Ubiquiti UniFi 6 LR access point:
mtk_soc_eth 1b100000.ethernet eth0: PHY [mdio-bus:08] driver [Aquantia AQR112C] (irq=POLL)
mtk_soc_eth 1b100000.ethernet eth0: configuring for phy/2500base-x link mode
mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable Aquantia Ethernet PHY driver as there is an AQR112C 2500Base-T
PHY in the Ubiquiti UniFi 6 LR access point.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add ethernet0 alias in device tree to make U-Boot inherit the Ethernet
mac address (set via environment variable 'ethaddr') down to Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
BMT replaces nand-specific ops for erasing and writing, but the
mtk-snand driver only implements generic mtd api.
Replace erase, block_isbad, block_markbad in mtd_info for generic mtd
drivers.
Fixes: b600aee3ed ("mediatek: attach bmt to the new snand driver")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
There's no such thing as ucidef_set_interfaces_lan. It's
ucidef_set_interface_lan.
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Similar to mt7623, also no longer use 'blockdev' and stop relying on
in-kernel partition parsers. Instead, strip off all metadata using
'fwtool' while writing the firmware image and scrape the number of
blocks written from 'dd', then use that block offset to stash the
configuration backup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Re-reading the partition table doesn't work reliably, it fails if
anything on the device is still in use and it's not trivial to prevent
every possible case of a block device still being in use somehow.
Therefore, instead of relying on the in-kernel partition parser to know
where to write the configuration backup, use OpenWrt's format-agnostic
fwtool to strip off all metadata from the image and count its blocks
while writing. In that way we can know where to write the config backup
without needing the kernel to parse the MBR and FIT structures.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
In case of the block device still being in use, re-reading the
partition table fails. In that case, abort sysupgrade to avoid
corrupting the just-written image because of wrong offsets caused
by failure to re-read the partition table.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable kernel options to allow loading device tree overlay via configfs
at runtime. This is useful for devboards like the BPi-R2 and BPi-R64
which got RasbPi-compatible 40-pin GPIO header which allow all sorts
of extensions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All subtargets only provide files and patches for Linux 5.10 by now
so there is little use for the old Linux 5.4 stuff. Remove it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add common features 'gpio', 'nand', 'pci', 'pcie', 'squashfs' and 'usb'
for all mediatek targets, add 'display' and 'usbgadget' for MT7623.
Sort features alphabetically while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
User reported that R64 doesn't provide power to the mPCIe slot in case
the PCIe port is disabled as it is when selecting the SATA
configuration. As users may still want to use USB-connected mPCIe
modules in CN8 slot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.
This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Specifications:
- SoC: MT7622
- RAM: 512MB
- Flash: MX35LF1GE4AB 128MB SPI NAND
- Ethernet: RTL8367S 5x1GbE
- WiFi: 2.4G: MT7622 5G: MT7615N x2
- Other ports: USB3.0 x1
Flash instruction:
*important*: upgrade vendor firmware to at least V7.1cu.643_B20200521
1. hold the reset button and power on the device. wait for about 10s
before releasing the reset button.
2. upload sysupgrade.bin via u-boot recovery page on http://192.168.1.1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Based on the existing documentation [1][2], I dare anyone to demonstrate that
we need to fine-tune these RCU parameters. The (performance) breakage potential
for doing so is immense, so let's just please put down this loaded footgun.
Disable CONFIG_RCU_EXPERT and its dependent symbols. Additionally, remove the
CONFIG_RCU_EXPERT symbol from the target kconfigs which contain it.
[1] https://www.kernel.org/doc/Documentation/RCU/Design/Data-Structures/Data-Structures.html
[2] https://lwn.net/Articles/777214/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
These options doesn't show up unless some kernel packages are selected,
so they are not covered by kernel_menuconfig.
Manually add them so that a build with all kmods can pass without user
interaction.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
there's no driver level remapping of oob data in the new spi-nand
driver and bmt oob signature starts at 0x0 of the dumped oob data.
change the default value to 0 for the new spi-nand driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
mtd->size will be overrided by BMT which makes all mtd requests made by
bmt fail in request size checking.
this commit changes the driver to check against actual chip size in chip
info as a workaround.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
we now have a standalone mtd driver and the old spi-mem driver along
with the hack in spi-nand core can be removed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch enables new spi-nand driver for mt7622 and mt7629.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch adds a new spi-nand driver which implements the SNFI of mt7622
and mt7629.
Unlike the existing snfi driver which makes use of the spi-mem framework
and the spi-nand framework with modified ecc support, this driver is
implemented directly on the mtd framework with other components untouched,
and provides better performance, and behaves exactly the same as the nand
framework.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Built clock drivers for G3DSYS and AUDSYS into the kernel to allow
multimedia features (GPU and audio) to work if they exist.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport support for dual-role USB 2.0 as that's what is actually
built-into MT7623.
Improve HDMI console by enabling VT and setting up tty1..tty6.
Re-add accidentally removed CONFIG_ARM_ARCH_TIMER.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to make HDMI console available on the BananaPi BPi-R2 select
various Kconfig symbols which are useful for systems with graphics.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
kirkwood build broke due to missing include needed for ETH_ALEN.
Add patch (sent upstream as well) to address that.
Refresh patches for 5.4 and 5.10.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MT7622 provides are hardware RNG with upstream Linux driver. Enable
compilation of this driver to make use of the hardware RNG.
Signed-off-by: David Bauer <mail@david-bauer.net>
The 1st generation MediaTek PCIe host bridge cannot handle Message
Signaled Interrupts (MSIs). The core PCI code is not aware that MSI is
not available. This results in warnings of the form:
WARNING: CPU: 2 PID: 112 at include/linux/msi.h:219
pci_msi_setup_msi_irqs.constprop.8+0x64/0x6c
Modules linked in: ahci(+) libahci libata sd_mod scsi_mod
gpio_button_hotplug
CPU: 2 PID: 112 Comm: kmodloader Not tainted 5.10.52 #0
Hardware name: Mediatek Cortex-A7 (Device Tree)
Import patches that introduce the 'no_msi' attribute to signal missing
MSI support to the core PCI.
Refresh patches:
- 000-spi-fix-fifo.patch
- 330-mtk-bmt-support.patch
- 510-net-mediatek-add-flow-offload-for-mt7623.patch
- 601-PCI-mediatek-Use-regmap-to-get-shared-pcie-cfg-base.patch
- 610-pcie-mediatek-fix-clearing-interrupt-status.patch
- 700-net-ethernet-mtk_eth_soc-add-support-for-coherent-DM.patch
- 710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
This patch did not apply cleanly any more after support for the XTX
flash was added to the generic patches.
Fixes: 92012dd867 ("kernel: Add support for XTX XT26G02A SPI NAND")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch fixes the fifo rx mode for the mt7623. It is already accepted
upstream for Linux Kernel 5.15.
To test the spi we can change the dts file to
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins_a>;
status = "okay";
spidev: spidev@0 {
compatible = "linux,spidev";
spi-max-frequency = <1000000>;
reg = <0>;
};
};
Afterwards we should see a spidev device under /dev/.
To test it we can further use spidev-test.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The image generation code for the U7623 board expects ext4 filesystem
to be selected in menuconfig and CONFIG_TARGET_ROOTFS_PARTSIZE to be
defined. Now that ext4 isn't enabled any more, the variable was missing
and broke the build.
Set the default (104) instead of using the config variable to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When reworking the BPi-R2 the mtk-mmc-img build step was removed
despite it was still needed to build the image for the UniElec U7623
board. Add it back for now until U7623 gets its facelift.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A full read-write rootfs cannot work inside uImage.FIT as the hash
will obviously change once writing to it. Disable generating ext4
rootfs images.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* introduce recovery (=initramfs) vs. production dual boot scheme
* make use of uImage.FIT (instead of FAT partition)
* generate images using build steps (instead of external scripts)
* simplify sysupgrade and config restore (thanks to uImage.FIT)
* make sure mmc devices are ordered persistently (set DT aliases)
This commit breaks sysupgrade from existing installations, you will
have to re-install using the sdcard.img.gz image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware flow offloading was reported to work when setting the right
version identifier. Import a patch from Frank Wunderlich doing that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update Kernel config and set Linux 5.10 for mediatek/mt7623.
(patches have already been updated to 5.10 when mt7622 was bumped)
Tested on Bananapi BPi-R2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Manually rebased:
bcm27xx/patches-5.4/950-0089-cgroup-Disable-cgroup-memory-by-default.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
