mirror of
https://github.com/openwrt/openwrt.git
synced 2025-04-14 06:27:03 +00:00
mediatek: mt7622: add support for ELECOM WRC-X3200GST3
ELECOM WRC-X3200GST3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on MT7622B. Specifications: - SoC : MediaTek MT7622B - RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK) - Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG) - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7622B (SoC) - 5 GHz : MediaTek MT7915A - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7531 - LEDs/Keys : 6x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J19: 3.3V, GND, TX, RX from power jack side - 115200n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-X3200GST3 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC Addresses: LAN : 04:AB:18:xx:xx:77 (Factory, 0x7FFF4 (hex)) WAN : 04:AB:18:xx:xx:78 (Factory, 0x7FFFA (hex)) 2.4 GHz: 04:AB:18:xx:xx:79 (Factory, 0x4 (hex)) 5 GHz : 04:AB:18:xx:xx:7A (none) Note: - currently, there is no "phy1tpt" trigger for 5 GHz wlan (MT7915) in "trigger" file of LEDs, use "phy1radio" trigger instead Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi
Daniel Golle
parent
e01b1c22df
commit
58b3b557b6
436
target/linux/mediatek/dts/mt7622-elecom-wrc-x3200gst3.dts
Normal file
436
target/linux/mediatek/dts/mt7622-elecom-wrc-x3200gst3.dts
Normal file
@ -0,0 +1,436 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
#include "mt7622.dtsi"
|
||||
#include "mt6380.dtsi"
|
||||
|
||||
/ {
|
||||
model = "ELECOM WRC-X3200GST3";
|
||||
compatible = "elecom,wrc-x3200gst3", "mediatek,mt7622";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
label-mac-device = &wan;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 swiotlb=512";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x1f000000>;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-0 {
|
||||
label = "red:wps";
|
||||
gpios = <&pio 47 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WPS;
|
||||
};
|
||||
|
||||
led_power_red: led-1 {
|
||||
label = "red:power";
|
||||
gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
function-enumerator = <1>;
|
||||
};
|
||||
|
||||
led_power_green: led-2 {
|
||||
label = "green:power";
|
||||
gpios = <&pio 49 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
function-enumerator = <2>;
|
||||
};
|
||||
|
||||
led-3 {
|
||||
label = "blue:power";
|
||||
gpios = <&pio 50 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
function-enumerator = <3>;
|
||||
};
|
||||
|
||||
led-4 {
|
||||
label = "white:wlan2g";
|
||||
gpios = <&pio 85 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
function-enumerator = <1>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
led-5 {
|
||||
label = "white:wlan5g";
|
||||
gpios = <&pio 89 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
function-enumerator = <2>;
|
||||
linux,default-trigger = "phy1radio";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
ap {
|
||||
label = "ap";
|
||||
gpios = <&pio 42 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
router {
|
||||
label = "router";
|
||||
gpios = <&pio 43 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&pio 102 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cpu0 {
|
||||
proc-supply = <&mt6380_vcpu_reg>;
|
||||
sram-supply = <&mt6380_vm_reg>;
|
||||
};
|
||||
|
||||
&cpu1 {
|
||||
proc-supply = <&mt6380_vcpu_reg>;
|
||||
sram-supply = <&mt6380_vm_reg>;
|
||||
};
|
||||
|
||||
&pio {
|
||||
eth_pins: eth-pins {
|
||||
mux {
|
||||
function = "eth";
|
||||
groups = "mdc_mdio", "rgmii_via_gmac2";
|
||||
};
|
||||
};
|
||||
|
||||
pcie0_pins: pcie0-pins {
|
||||
mux {
|
||||
function = "pcie";
|
||||
groups = "pcie0_pad_perst",
|
||||
"pcie0_1_waken",
|
||||
"pcie0_1_clkreq";
|
||||
};
|
||||
};
|
||||
|
||||
pmic_bus_pins: pmic-bus-pins {
|
||||
mux {
|
||||
function = "pmic";
|
||||
groups = "pmic_bus";
|
||||
};
|
||||
};
|
||||
|
||||
pwm7_pins: pwm1-2-pins {
|
||||
mux {
|
||||
function = "pwm";
|
||||
groups = "pwm_ch7_2";
|
||||
};
|
||||
};
|
||||
|
||||
/* Serial NAND is shared pin with SPI-NOR */
|
||||
serial_nand_pins: serial-nand-pins {
|
||||
mux {
|
||||
function = "flash";
|
||||
groups = "snfi";
|
||||
};
|
||||
|
||||
conf-cmd-data {
|
||||
pins = "SPI_WP", "SPI_HOLD", "SPI_MOSI",
|
||||
"SPI_MISO", "SPI_CS";
|
||||
drive-strength = <16>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
conf-clk {
|
||||
pins = "SPI_CLK";
|
||||
drive-strength = <16>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
uart0_pins: uart0-pins {
|
||||
mux {
|
||||
function = "uart";
|
||||
groups = "uart0_0_tx_rx" ;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog_pins: watchdog-pins {
|
||||
mux {
|
||||
function = "watchdog";
|
||||
groups = "watchdog";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <ð_pins>;
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
|
||||
phy-connection-type = "2500base-x";
|
||||
|
||||
nvmem-cells = <&macaddr_factory_7fff4>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
mdio-bus {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
switch@0 {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <0>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
|
||||
reset-gpios = <&pio 54 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
wan: port@0 {
|
||||
reg = <0>;
|
||||
label = "wan";
|
||||
|
||||
nvmem-cells = <&macaddr_factory_7fffa>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
label = "cpu";
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&bch {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&snfi {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&serial_nand_pins>;
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
nand-ecc-engine = <&snfi>;
|
||||
mediatek,bmt-v2;
|
||||
mediatek,bmt-table-size = <0x1000>;
|
||||
mediatek,bmt-remap-range = <0x0 0x8c0000>,
|
||||
<0x1bc0000 0x30c0000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Preloader";
|
||||
reg = <0x0 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "ATF";
|
||||
reg = <0x80000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
label = "u-boot";
|
||||
reg = <0xc0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x140000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@1c0000 {
|
||||
label = "factory";
|
||||
reg = <0x1c0000 0x100000>;
|
||||
read-only;
|
||||
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
reg = <0x4 0x6>;
|
||||
};
|
||||
|
||||
macaddr_factory_7fff4: macaddr@7fff4 {
|
||||
reg = <0x7fff4 0x6>;
|
||||
};
|
||||
|
||||
macaddr_factory_7fffa: macaddr@7fffa {
|
||||
reg = <0x7fffa 0x6>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@2c0000 {
|
||||
label = "kernel";
|
||||
reg = <0x2c0000 0x600000>;
|
||||
};
|
||||
|
||||
partition@8c0000 {
|
||||
label = "ubi";
|
||||
reg = <0x8c0000 0x1300000>;
|
||||
};
|
||||
|
||||
partition@1bc0000 {
|
||||
label = "tm_pattern";
|
||||
reg = <0x1bc0000 0x500000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20c0000 {
|
||||
label = "tm_key";
|
||||
reg = <0x20c0000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@21c0000 {
|
||||
label = "user_data";
|
||||
reg = <0x21c0000 0xf00000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30c0000 {
|
||||
label = "reserved";
|
||||
reg = <0x30c0000 0x4f40000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pcie0_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&slot0 {
|
||||
status = "okay";
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&factory 0x5000>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
nvmem-cells = <&macaddr_factory_4>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
mac-address-increment = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm7_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwrap {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_bus_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&rtc {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart0_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&watchdog_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
@ -137,6 +137,26 @@ define Device/elecom_wrc-2533gent
|
||||
endef
|
||||
TARGET_DEVICES += elecom_wrc-2533gent
|
||||
|
||||
define Device/elecom_wrc-x3200gst3
|
||||
DEVICE_VENDOR := ELECOM
|
||||
DEVICE_MODEL := WRC-X3200GST3
|
||||
DEVICE_DTS := mt7622-elecom-wrc-x3200gst3
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
IMAGE_SIZE := 25600k
|
||||
KERNEL_SIZE := 6144k
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
UBINIZE_OPTS := -E 5
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
||||
append-ubi | check-size | \
|
||||
elecom-wrc-gs-factory WRC-X3200GST3 0.00 -N | \
|
||||
append-string MT7622_ELECOM_WRC-X3200GST3
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
DEVICE_PACKAGES := kmod-mt7915e
|
||||
endef
|
||||
TARGET_DEVICES += elecom_wrc-x3200gst3
|
||||
|
||||
define Device/linksys_e8450
|
||||
DEVICE_VENDOR := Linksys
|
||||
DEVICE_MODEL := E8450
|
||||
|
||||
@ -9,6 +9,7 @@ mediatek_setup_interfaces()
|
||||
|
||||
case $board in
|
||||
bananapi,bpi-r64|\
|
||||
elecom,wrc-x3200gst3|\
|
||||
linksys,e8450|\
|
||||
linksys,e8450-ubi|\
|
||||
mediatek,mt7622-rfb1|\
|
||||
|
||||
@ -32,6 +32,12 @@ platform_do_upgrade() {
|
||||
nand_do_upgrade "$1"
|
||||
fi
|
||||
;;
|
||||
elecom,wrc-x3200gst3|\
|
||||
mediatek,mt7622-rfb1-ubi|\
|
||||
totolink,a8000ru|\
|
||||
xiaomi,redmi-router-ax6s)
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
linksys,e8450-ubi)
|
||||
CI_KERNPART="fit"
|
||||
nand_do_upgrade "$1"
|
||||
@ -44,11 +50,6 @@ platform_do_upgrade() {
|
||||
fi
|
||||
default_do_upgrade "$1"
|
||||
;;
|
||||
mediatek,mt7622-rfb1-ubi|\
|
||||
totolink,a8000ru|\
|
||||
xiaomi,redmi-router-ax6s)
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
*)
|
||||
default_do_upgrade "$1"
|
||||
;;
|
||||
@ -67,6 +68,7 @@ platform_check_image() {
|
||||
buffalo,wsr-2533dhp2)
|
||||
buffalo_check_image "$board" "$magic" "$1" || return 1
|
||||
;;
|
||||
elecom,wrc-x3200gst3|\
|
||||
mediatek,mt7622-rfb1-ubi|\
|
||||
totolink,a8000ru|\
|
||||
xiaomi,redmi-router-ax6s)
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user