Commit Graph

3683 Commits

Author SHA1 Message Date
Oleksandr Zharov
998c34d3fe
ramips: add Xiaomi RA75 red signal led
RA75 has 5 physical LEDs under 2 indicators, mixed with light pipes:
Indicator "System":
  GPIO0: blue
  GPIO2: amber
Indicator "Signal":
  GPIO44: blue
  GPIO37: amber
  GPIO46: red

All except GPIO46 were already added by Jo Deisenhofer. GPIO46 is used for UART1 by
default, so it needs additional pin control change in devicetree to be operational.
Verified on my RA75.

Signed-off-by: Oleksandr Zharov <alex.zeed@gmail.com>
2023-04-17 18:59:28 +02:00
Álvaro Fernández Rojas
8758438c27 ramips: sercomm-payload: use pide-file argument
Instead of passing an array of hex bytes for the Sercomm PID we can now use
the --pid-file parameter.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-09 09:59:21 +02:00
John Audia
78a468f690 kernel: bump 5.10 to 5.10.177
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-04-08 15:32:01 +02:00
Joe Mullally
2122c80b32 ramips: lower re305-v3 spi-max-frequency
Fix flash I/O instability observed in newer devices with cFeon
QH64A-104HIP (detected as en25qh64).

Ref: https://forum.openwrt.org/t/support-for-tp-link-re305-v3/75893/91

Reported-by: Dimitri Souza <dimitri.souza@gmail.com>
Tested-by: Dimitri Souza <dimitri.souza@gmail.com>
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[alter commit-message - target master]
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-04-08 14:41:01 +02:00
David Bauer
076da59f17 ramips: define remapping-range for DAP-X1860
Prevent the BBT translation layer from remapping the UBI used for
storing rootfs.

Explicitly define the number of blocks reserved for remapping.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-04-08 14:41:01 +02:00
Bin We
6b66666da4 ramips: add support for OrayBox X1
Add support for OrayBox X1. It is a 802.11n router, based on MediaTek MT7628N.

Specifications:
SoC: MediaTek MT7628N (580MHz)
RAM: 64 MiB
Flash: 16 MiB NOR (Winbond W25Q128JVSIQ)
Wireless: 802.11b/g/n 2x2 2.4GHz (Built In)
Ethernet: 1x 100Mbps only
USB: 1x USB Type-A 2.0 Host Port
Button: 1x "Reset" button
LED: 1x Blue LED + 1x Red LED + 1x White LED
Power: 5V Micro-USB input

Manufacturer Page:
https://pgy.oray.com/router/x1.html/parameter

Flash Layout:
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "kpanic"
0x000000040000-0x000000050000 : "factory"
0x000000050000-0x000000fe0000 : "firmware"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "reserve"

Install via SSH:
Original firmware is based on OpenWRT, but SSH is not start by default,
You should enable it first

1. Login into web admin (10.168.1.1), default password is 'admin'
2. Open the following link, and the result should be {"code":0};
SSH is now started, username is root, password is same as web admin password
http://10.168.1.1/cgi-bin/oraybox?_api=ssh_set&enabled=1
4. You can flash firmware via mtd: mtd write /tmp/firmware_image.bin firmware

Signed-off-by: Bin We <me@udp.pw>
2023-04-02 19:25:37 +02:00
Felix Baumann
cbf120c255 ramips: mt7621: add migration script for WLAN PCI paths
PCI paths of the WLAN devices have changed between kernel 5.10 and 5.15;
migrate config so existing wifi-iface definitions don't break.

This is implemented as a hotplug handler rather than a uci-defaults script
as the migration script must run before the 10-wifi-detect hotplug handler.

based on b452af23a8

migration was forgotten when device trees were adjusted in
688697889c
c77913be5b

fixes #9374

affected devices:
Netgear R6220
Netgear WAC104
Netgear WNDR3700 v5
Zbtlink ZBT-WE1326
Wiflyer WF3526-P
Arcadyan WE420223-99
Beeline Smartbox Flash (Arcadyan WG443223)
MTS WG430223 (Arcadyan WG430223)

Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-04-01 22:32:13 +02:00
Muhammad AL-Qadhy
2a04df3920 ramips: Add support for CJ-Hello HYC-G920
Hanyang Digitech Co., Ltd.
MSIP-CMM-HYD-HYC-G920
CJ-Hello HYC-G920

SoC		: MediaTek MT7621AT
RAM		: 256M (SK hynix H5TQ2G63FFR)
FLASH	: 16MB (Winbond W25Q128BV)
WiFi	: MediaTek MT7602EN bgn 2SS
WiFi	: MediaTek MT7612EN nac 2SS
BTN		: Reset
LED		: - Power RED
		  - WAN Green
		  - LAN {1-4}
		  - WiFi 2.4 GHz Blue
		  - WiFi 5 GHz Blue
		  - USB Green

**For MT7621 stage1 DDR Test**

UART	: J4 GND - 3V3 - TX - RX - GND / 57600-8N1

```
                MT7621   stage1 code 10:33:55 (ASIC)
                CPU=500000000 HZ BUS=166666666 HZ
```

**For u boot environment**

UART	: J4 GND - 3V3 - TX - RX - GND / 115200-8N1

**UART Menu**

```
	Please choose the operation:
		1: Load system code to SDRAM via TFTP.
		2: Load system code then write to Flash via TFTP.
		3: Boot system code via Flash (default).
		4: Entr boot command line interface.
		7: Load Boot Loader code then write to Flash via Serial.
		9: Load Boot Loader code then write to Flash via TFTP.
```

**Steps**

Press 4: Entr boot command line interface.

On the pormpt enter.
`setenv firmware_size 0xf60000`
Then enter.
`saveenv`
Then enter.
`reset`

**Device will reboot**

Set your IP 192.168.100.100/24
Connect your lan cable to wan port.

**On the UART Menu**

Press 2: Load system code then write to Flash via TFTP.

 Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) **enter** `Y`
 Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.100.55) ==:`192.168.100.55`
        Input server IP (192.168.100.100) ==:`192.168.100.100`
        Input Linux Kernel filename () ==:`openwrt-22.03.0-ramips-mt7621-hanyang_hyc-g920-squashfs-sysupgrade.bin`

After uploading firmware image, device will boot Openwrt.

Signed-off-by: Muhammad AL-Qadhy <m.ismael@gmail.com>
2023-04-01 22:13:16 +02:00
Rosen Penev
37dbe30215 ramips: mt7621: remove set-affinity script
From https://github.com/openwrt/openwrt/pull/12280#issuecomment-1489279860
On Ethernet and WLAN, NAPI is threaded for all queues. This means that the
processing work is not stuck on the CPU that fired the IRQ. Under heavy
load, IRQs get disabled anyway, so it should not matter at all which CPUs
the IRQs fire on.

Basic testing indicates this to be true. There's no speedup or slowdown.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-04-01 21:56:28 +02:00
Felix Baumann
787ecdf66d ramips: mt7621: ASUS RT-AX53U add NMBM, nest firmware
Nests kernel and ubi into firmware partition in-order to be compatible
with OEM firmware. This allows restoring oem firmware from a backup of
firmware2. Add jffs2 partition which is present in the oem firmware.
Add support for mediatek NMBM (wear leveling on newer mediatek devices).
Exclude UBI partition from NMBM management.
Continues PR #10685.

Tested-by: Felix Baumann <felix.bau@gmx.de>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-04-01 21:34:46 +02:00
John Audia
ec8c837eab kernel: bump 5.15 to 5.15.105
Manually rebased:

Removed upstreamed:
	backport-5.15/743-v6.3-0005-net-dsa-b53-mmap-fix-device-tree-support.patch[1]
	backport-5.15/743-v6.3-0006-net-dsa-tag_brcm-legacy-fix-daisy-chained-switches.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.105&id=9bbb3d3f218f1cf51f57a43cf8fd63b05be1b821
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.105&id=48f52431af9980582b6faa32ff8b581edb10486c

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-04-01 19:58:44 +02:00
Hauke Mehrtens
9186da4027 ramips: Refresh patches
Refresh the ramips kernel patches.

Fixes: 7472476aef ("kernel: fix mtk_eth_soc throughput regressions on gigabit PHY ports")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-03-29 19:36:33 +02:00
Daniel Golle
53dc9a60c0 generic: mtk_eth_soc: switch to external PCS driver
Backport patch to make use of the new PCS driver in mtk_eth_soc.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Daniel Golle
027586ae8e generic: backport some phylink helper functions
It isn't feasible to literally backport all upstream phylink_pcs changes
down to Linux 5.15: It's just too many patches, and many downstream
drivers and hacks are likely to break. We are too close to branching off
to risk this, and it's also just too much work.
Instead just add helper functions used by modern PCS drivers while keeping
the original functions instact as well. While this may add a kilobyte or
two of extra kernel size, it has the advantage that we get the best of both
worlds: None of the existing codepaths are touched, but yet we have the
option to backport singular improvements to Ethernet drivers where needed.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-03-27 19:07:54 +01:00
Alexey Bartenev
dc79b51533 ramips: add support for Keenetic Lite III rev. A
General specification:
SoC Type: MediaTek MT7620N (580MHz)
ROM: 8 MB SPI-NOR (W25Q64FV)
RAM: 64 MB DDR (EM6AB160TSD-5G)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Buttons: 3 button (POWER, RESET, WPS)
Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT)
Bootloader: U-Boot 1.1.3
Power: 9 VDC, 0.6 A

MAC in stock:
|-	+			|
| LAN 	| RF-EEPROM + 0x04	|
| WLAN	| RF-EEPROM + 0x04	|
| WAN 	| RF-EEPROM + 0x28	|

OEM easy installation
1. Use a PC to browse to http://my.keenetic.net.
2. Go to the System section and open the Files tab.
3. Under the Files tab, there will be a list of system
files. Click on the Firmware file.
4. When a modal window appears, click on the Choose File
button and upload the firmware image.
5. Wait for the router to flash and reboot.

OEM installation using the TFTP method
1. Download the latest firmware image and rename it to
klite3_recovery.bin.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the
firmware image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect
the PC to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address
192.168.1.2 and subnet mask 255.255.255.0.
5. Power up the router while holding the reset button pressed.
6. Wait approximately for 5 seconds and then release the
reset button.
7. The router should download the firmware via TFTP and
complete flashing in a few minutes.
After flashing is complete, use the PC to browse to
http://192.168.1.1 or ssh to proceed with the configuration.

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2023-03-27 02:09:58 +02:00
Shiji Yang
88d76bb455 ramips: mt7621: enable unused PCIe port to fix potential boot failure
One user reported that his SIMAX1800T couldn't boot like the others. After
debugging, I found that this was caused by the disabled PCIe port. I cannot
reproduce this issue on my SIMAX1800T. But when I disabled pcie2 on the
ASUS RT-AC57U, I got the same result.

It seems that disabling these unused PCIe ports on some mt7621 revisions
will cause PCIe to fail to initialize. So we'd better to re-enable them on
all related mt7621 devices.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-03-26 23:33:24 +02:00
Chuanhong Guo
2126325400
ramips: fix 5g mac for TOTOLINK X5000R
There's no valid mac address for the second band in the eeprom.
The vendor fw uses 2.4G mac + 4 as the mac for 5G radio.
Do the same in our firmware.

Fixes: 23be410b3d ("ramips: add support for TOTOLINK X5000R")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2023-03-26 23:55:54 +08:00
John Audia
d59d69f9e1 kernel: bump 5.15 to 5.15.103
Manually rebased:
        backport-5.15/704-15-v5.19-net-mtk_eth_soc-move-MAC_MCR-setting-to-mac_finish.patch

Removed upstreamed:
        backport-5.15/060-v6.0-01-tools-build-Add-feature-test-for-init_disassemble_in.patch[1]
        backport-5.15/060-v6.0-02-tools-include-add-dis-asm-compat.h-to-handle-version.patch[2]
        backport-5.15/060-v6.0-03-tools-perf-Fix-compilation-error-with-new-binutils.patch[3]
        backport-5.15/060-v6.0-04-tools-bpf_jit_disasm-Fix-compilation-error-with-new-.patch[4]
        backport-5.15/060-v6.0-05-tools-bpftool-Fix-compilation-error-with-new-binutil.patch[5]
        pending-5.15/733-02-net-ethernet-mtk_eth_soc-fix-RX-data-corruption-issu.patch[6]
        bcm47xx/patches-5.15/170-bgmac-fix-initial-chip-reset-to-support-BCM5358.patch[7]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=51b99dc38c1a053e2e732d7f9e2740e343ae7eae
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=451c9d7b16169645ed291ebb2ca9844caa088f2d
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=97f005c0bdbaf656a7808586d234965385a06c58
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=1c27fab243333821375e4d63128d60093fdbe149
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=4441a90091931fd81607567961dc122f24f735bb
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=2adc29350a5b4669544566f71f208d2abaec60ab
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=04bfc5bcdfc0fdb73587487c71b04d63807ae15a

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-03-25 16:01:23 +01:00
David Bauer
47de2c6862 ramips: add support for Mercusys MR70X
Hardware
========
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: Winbond W25Q128JV (SPI-NOR 16MB)
- WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC)
- UART: >TX RX GND 3v3 (115200 8N1, J1)
        Do not connect 3v3. TX is marked with an arrow.

Installation
============
Flash factory image. This can be done using stock web ui.

Revert to stock firmware
========================
Flash stock firmware via OEM Web UI Recovery mode.

Web UI Recovery method
======================
1. Unplug the router
2. Plug in and hold reset button 5~10 secs
3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0
4. Flash image with web browser to 192.168.1.1

Co-authored-by: Robert Senderek <robert.senderek@10g.pl>
Co-authored-by: Yoonji Park <koreapyj@dcmys.kr>
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-24 15:32:57 +01:00
Tony Butler
889bbf89bb ramips: mt7621: enable lzma-loader for AFOUNDRY EW1200
Fixes boot loader LZMA decompression issues (LZMA ERROR 1)
As reported in issue #12208

Reported-by: Raúl M. <raul.m@sparkedhost.com>
Tested-by: Raúl M. <raul.m@sparkedhost.com>
Signed-off-by: Tony Butler <spudz76@gmail.com>
2023-03-22 22:05:51 +01:00
David Bauer
d52870125d ramips: fix Archer AX23 WiFi MAC address conflict
The original claim about conflicting MAC addresses is wrong. mac80211
does increment the first octet and sets the LA bit.

This means our "workaround" actually leads to the issue while
incrementing the last octet is safe.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-21 05:10:03 +01:00
Óscar García Amor
ca330cac92 ramips: cudy wr1300v2 reduce SPI freq to 40000000
Cases have been reported in which certain devices do not boot correctly
or have errors. After various tests by users who have such errors it has
been concluded that the SPI frequency should be reduced to 40Mhz, at
this speed it appears that all devices work correctly.

Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
2023-03-20 23:48:08 +01:00
John Audia
3ca9849589 kernel: bump 5.10 to 5.10.175
Manually rebased:
	backport-5.10/611-v5.12-net-ethernet-mediatek-support-setting-MTU.patch

Removed upstreamed:
	bcm47xx/patches-5.10/170-bgmac-fix-initial-chip-reset-to-support-BCM5358.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.175&id=cbf11ff3708ff163387da924f80a47ce7c721e9b

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-03-20 22:44:28 +01:00
John Audia
d4aad642ff kernel: bump 5.10 to 5.10.173
Manually rebased:
        ramips/patches-5.10/810-uvc-add-iPassion-iP2970-support.patch

All other patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-03-20 22:44:28 +01:00
John Audia
d6d8851d12 kernel: bump 5.15 to 5.15.100
Manually rebased:
        bcm27xx/patches-5.15/950-0421-Support-RPi-DPI-interface-in-mode6-for-18-bit-color.patch
        bcm27xx/patches-5.15/950-0706-media-i2c-imx219-Scale-the-pixel-clock-rate-for-the-.patch
        ramips/patches-5.15/810-uvc-add-iPassion-iP2970-support.patch

Removed upstreamed:
        bcm27xx/patches-5.15/950-0707-drm-vc4-For-DPI-MEDIA_BUS_FMT_RGB565_1X16-is-mode-1-.patch[1]
        bcm27xx/patches-5.15/950-0596-drm-vc4-dpi-Add-option-for-inverting-pixel-clock-and.patch[2]
        ipq807x/0006-v5.16-arm64-dts-qcom-Fix-IPQ8074-PCIe-PHY-nodes.patch [3]
        ipq807x/0034-v6.1-arm64-dts-qcom-ipq8074-fix-PCIe-PHY-serdes-size.patch [4]
        ipq807x/0103-arm64-dts-qcom-ipq8074-fix-Gen2-PCIe-QMP-PHY.patch [5]
        ipq807x/0104-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-QMP-PHY.patch [6]
        ipq807x/0105-arm64-dts-qcom-ipq8074-correct-Gen2-PCIe-ranges.patch [7]
        ipq807x/0108-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-node.patch [8]
        ipq807x/0109-arm64-dts-qcom-ipq8074-correct-PCIe-QMP-PHY-output-c.patch [9]
        ipq807x/0132-arm64-dts-qcom-ipq8074-correct-USB3-QMP-PHY-s-clock-.patch [10]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.99&id=d2991e6b30020e286f2dd9d3b4f43548c547caa6
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/gpu/drm/vc4/vc4_dpi.c?h=v5.15.100&id=8e04aaffb6de5f1ae61de7b671c1531172ccf429
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=a55a645aa303a3f7ec37db69822d5420657626da
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=d9df682bcea57fa25f37bbf17eae56fa05662635
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=7e6eeb5fb3aa9e5feffdb6e137dcc06f5f6410e1
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=e88204931d9a60634cd50bbc679f045439c4b91d
7.  https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=1563af0f28afd3b6d64ac79a2aecced3969c90bf
8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=feb8c71f015d416f1afe90e1f62cf51e47376c67
9. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=69c7a270357a7d50ffd3471b14c60250041200e3
10. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=dd3d021ae5471d98adf81f1e897431c8657d0a18

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Tested-by: Robert Marko <robimarko@gmail.com> #ipq807x/Dynalink WRX36
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, ath79/tl-wdr3600, ipq806x/g10, ipq806x/nbg6817
2023-03-18 12:52:17 +01:00
Eneas U de Queiroz
4662adef2a
uencrypt: add support for mbedtls
This commit includes some additional changes:
 - better handling of iv and keys in openssl/wolfssl variants
 - fix compiler warnings and whitespace
 - build all 3 variants as separate packages
 - adjust the new package name in targets' DEVICE_PACKAGES
 - remove PKG_FLAGS:=nonshared

[Beeline SmartBox Flash - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
[after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2023-03-17 17:22:53 -03:00
David Bauer
7dceef5ee5 ramips: add support for TP-Link Archer AX23 v1
Hardware
--------
CPU:    MediaTek MT7621 DAT
RAM:    128MB DDR3 (integrated)
FLASH:  16MB SPI-NOR ()
WiFi:   MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
        LEDs - (3V3 - GND - RX - TX) - ETH ports

Installation
------------

Upload the factory image using the Web-UI.

Web-Recovery
------------

The router supports a HTTP recovery mode by holding the reset-button
when powering on. The interface is reachable at 192.168.0.1 and supports
installation using the factory image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-15 01:44:29 +01:00
Aleksey Nasibulin
d45659a571 ramips: add support for SNR-CPE-ME2-SFP
SNR-CPE-ME2-SFP is a wireless router with SFP cage manufactured by SNR/NAG company.

Specification:
- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB (GD25Q127CSIG)
- RAM:  256 MB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7615DN)
- Ethernet: 4x 10/100/1000 Mbps
- SFP cage (using RTL8211FS-CG)
- USB 3.0 port
- Power: 12 VDC, 2 A

Flash instruction via TFTP:
1. Boot SNR-CPE-ME2 to recovery mode
  (press reset button and power on device, hold button for ~10 seconds)
2. Send firmware via TFTP client:
 TFTP Server address: 192.168.1.1
 TFTP Client address: 192.168.1.131
3. Wait ~120 seconds to complete flashing
4. Do sysupgrade using web-interface

MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use      | address          | example           |
+----------+------------------+-------------------+
| Device   | label            | 6A:C4:DD:xx:xx:28 |
| Ethernet | + 1              | 6A:C4:DD:xx:xx:29 |
| 2g       | + 2              | 6A:C4:DD:xx:xx:2A |
| 5g       | + 3              | 6A:C4:DD:xx:xx:2B |
+----------+------------------+-------------------+

Notes:
- Reading sfp eeprom is not supported [1] (driver issue). Stock image has the same situation.

References:
1. https://forum.openwrt.org/t/mt7621-and-reading-sfp-eeprom/152249

Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
2023-03-08 23:44:59 +01:00
André Fonseca
3817577c92 ramips: mt7621: TP-Link EAP235/615-Wall: add poe passthrough gpio definitions
Add the missing definitions for the PoE passthrough functionality.
The relevant pin is already being exported, but it is missing from
the initial board configuration file. With this change, the user is
now able to toggle the PoE passthorough functionality via the uci cli

Signed-off-by: André Fonseca <mail@andrefonseca.pt>
2023-03-04 17:37:25 +01:00
Mikhail Zhilkin
1f53fa2b83 ramips: fix wrong pcie port number for Arcadyan WE420223-99
Wrong pcie port number for WLAN causes missing 5g WLAN interface with 5.15
kernel on Arcadyan WE420223-99 (KPN Experia WiFi).

This changes port from pcie0 to pcie1.

[1.331556] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[1.345299] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[1.359116] mt7621-pci 1e140000.pcie: PCIE1 enabled

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-03-04 13:34:08 +01:00
Hang Zhou
e451957166 ramips: add support for D-Link Dir-853 A1
Specifications:
* SoC: MT7621AT
* RAM: 256MB (NT5CC64M16GP-DI)
* Flash: 16MB NOR SPI flash (GD25Q127CSIG, using GD25Q128C driver)
* WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC
* Ethernet: 4x1000M LAN, 1x 1000M WAN
* LEDs: Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue,
  USB Blue
* Buttons: Reset,WPS, Wifi
* Serial interface: on board but not populated, pinout (from the DC jack
side to the WAN port side) is "3.3V Input Output Gnd". Baud rate is 57600,
settings are 8 data bits, no parity bit, one stop bit, and no flow control.

Stock flash layout:
```
GD25Q128C(c8 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K)
.numeraseregions = 0
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "Config2"
0x000000060000-0x000000fb0000 : "Kernel"
0x000000fb0000-0x000001000000 : "Private"
```
The kernel partition will be replaced with the OpenWrt image, the other
partitions are left untouched.

"Config2" seems to be the config storage used by the stock firmware.

"Private" is a 320kB empty JFFS2 partition that comes with the stock
firmware. One can get a larger space for OpenWrt by merging it with
"Kernel".

OpenWrt flash layout:
```
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "u-boot-env"
0x000000040000-0x000000050000 : "factory"
0x000000050000-0x000000060000 : "config2_stock"
0x000000060000-0x000000fb0000 : "firmware"
0x000000fb0000-0x000001000000 : "private_stock"
```

The OpenWrt image must have 96 bytes of padding in the header.

MAC addresses on OEM firmware:
|      		| location on the flash 	| notes    	|
|------		|-----------------------	|----------	|
| lan (eth2) 	| factory + 0xe000      	| on label 	|
| wan (eth3) 	| factory + 0xe006      	|          	|
| 2.4g (rax0) 	| not on flash          	| lan + 1  	|
| 5g (ra0) 	| not on flash          	| lan + 2  	|

Mac addresses of the 2.4g and 5g interface are stored as ASCII strings in
the u-boot-env partition, but they are not used. OpenWrt calculates
Wifi Mac addresses based on the LAN Mac.

Flash and test instructions:
Flash the encrypted image (available in the OpenWrt forum) through the
stock D-Dink web interface.

1. Open the case, and solder the 4-pin header near the WAN port.
2. Connect it to a USB-UART TTL (3.3V) adapter, no need to connect VCC.
3. Open a terminal emulator (e.g. `screen /dev/ttyUSB0` on linux) with
the settings mentioned above.
4. Setup a TFTP server on your PC that can serve
`xxx-ramips-mt7621-dlink_dir-853-a1-initramfs-kernel.bin`.
5. Connect any LAN port to your PC and set a static IPv4 address to
192.168.0.101 (netmask 255.255.255.0).
6. Power on the device and keeps pressing 1 until you see the prompt.
7. Use default IP addresses and enter the file name accordingly, then hit
enter.
8. Wait until it boots to OpenWrt, the default IP address is 192.168.1.1,
you need to change your PC network adapter to use DHCP in order to access
LUCI.
9. So far, the OpenWrt runs in RAM and the flash contents are not touched.
You can try OpenWrt without having to overwrite the stock firmware, a
reboot clears all changes.
10. Optionally, backup the stock firmware (the "firmware" partition) in
Luci.
11. To permantly install OpenWrt to the device , click
on "System -> Backup/Flash Firmware" in Luci and flash
`xxx-ramips-mt7621-dlink_dir-853-a1-squashfs-sysupgrade.bin`

Known problems:
* WLAN0 defaults to 5G after a fresh installation, to enable 2.4G network,
you need to config it manually in LUCI.

* If you see jffs2 related warnings/errors after updating from the stock
web interface, you need to do a reset in LUCI. The error will be gone after
a cold reboot.

Signed-off-by: Hang Zhou <929513338qq@gmail.com>
2023-03-04 13:23:18 +01:00
Bjørn Mork
79bd0172ca mt7621: move uboot-envtools to DEFAULT_PACKAGES
Several devices depend on fw_printenv during sysupgrade.  Make sure
it always is present in all images, including initramfs images built
by the buildbots.

Fixes: 2449a63208 ("ramips: mt7621: Add support for ZyXEL NR7101")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-03-01 23:24:23 +01:00
Sergio Paracuellos
84c04ff406 ramips: rt5350: enable lzma-loader for ALLNET ALL5003
Fixes the boot loader LZMA decompression issue:
LZMA ERROR 1 - must RESET board to recover

Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
2023-03-01 22:15:13 +01:00
Arınç ÜNAL
9df035b3ea treewide: remove label = "cpu" from DSA dt-binding
This is not used by the DSA dt-binding, so remove it from all devicetrees.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9cc115d8d6f73dd260de1609182f3645844d6907
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-26 22:22:48 +01:00
Karl Chan
5c04c3943e ramips: Alternative name Asus RT-AC750L for Asus RT-AC1200V2
The Asus RT-AC750L is identical to the already supported Asus RT-AC1200V2. Use the ALT0 buildroot tags to show both devices.

Reference : https://forum.openwrt.org/t/asus-rt-ac750l-is-the-same-as-rt-ac1200-v2/151783

Signed-off-by: Karl Chan <exkc@exkc.moe>
2023-02-26 17:46:27 +01:00
Felix Baumann
688697889c ramips: correct the PCIe port number for some mt7621 devices
MT7621 uses a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Netgear R6220, WAC104 and WNDR3700 v5.

According to bootlog, MT7612E (5GHz) is connected to pcie0, and
MT7603E (2GHz) is connected to pcie2:
[2.758986] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
[2.772862] mt7621-pci 1e140000.pcie: PCIE0 enabled
[2.782579] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[3.009151] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[3.125715] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000

Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[felix.bau@gmx.de: adjust commit message for Netgear devices]
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-25 20:21:36 +01:00
Shiji Yang
68004f1942 ramips: add alternative device name for Wiflyer WF3526-P
Wiflyer WF3526-P and Zbtlink ZBT-WE1326 have the same circuit design.
Installing the misunderstading firmware of ZBT-WE3526 will cause Wi-Fi
not work due to allocate the wrong pcie port. Add alternative name to
help users easily build or download the correct firmware.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-02-19 18:37:55 +01:00
Shiji Yang
c77913be5b ramips: correct the PCIe port number for Zbtlink ZBT-WE1326
MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Zbtlink ZBT-WE1326.

According to the bootlog, MT7612E (5 GHz) is connected to pcie1, and
MT7603E (2 GHz) is connected to pcie2:
[4.197658] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[4.204609] mt7621-pci 1e140000.pcie: PCIE1 enabled
[4.209476] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[4.307988] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[4.367206] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-02-19 18:37:55 +01:00
Arınç ÜNAL
efbb623deb ramips: add support for Huasifei WS1208V2
The Huasifei WS1208V2 is an AC1200 router featuring 5 Ethernet ports with a
Quectel RM520N-GL cellular modem which supports QMI and MBIM modes.

Specifications:
- MT7621AT, 256 MiB RAM, 16 MiB SPI Flash
- MT7603EN 2.4 GHz & MT7612EN 5 GHz WLAN
- Quectel RM520N-GL Cellular Modem
- 2 WLAN & 4 Cellular Antennas
- 5 Gigabit Ethernet Ports
- 1 USB 2.0 port
- 1 PCI-E Slot
- 1 M.2 slot
- 1 SIM card slot
- 1 SD card slot

Installation:
- Install sysupgrade image via ROOter OS.

TFTP Recovery:
- Connect to serial console.
- Boot initramfs image by choosing option 1 when U-Boot prompts.
- Install sysupgrade image via OpenWrt.

Link: https://www.huasifei.com/a/Products/5G%20CPE/240.html
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-18 19:56:37 +01:00
Michael Pratt
6f6d24a00a ramips: add label MAC address for EPG600 and ESR600
set label mac for the current ESR600 and new EPG600
using the board.d scripts

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Michael Pratt
4ef86c620f ramips: add support for Senao Engenius EPG600
FCC ID: A8J-EPG600

Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)

this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.

**Specification:**

  - MT7620 SOC		MIPS 24kec, 2.4 GHz WMAC, 2x2
  - RT5592N WLAN	PCI chip, 5 GHz, 2x2
  - QCA8337N Gb SW	RGMII GbE, SW P0 -- SOC P5, 5 LEDs
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 64 MB RAM		NT5TU32M16
  - UART console	J2, populated
  - USB 2.0 port	direct to SOC
  - 6 GPIO LEDs		power, 2G, 5G, wps2g, wps5g, line
  - 3 buttons		reset, wps, "reg" (registeration)
  - 4 antennas		internal omni-directional plates

NOT YET SUPPORTED: VoIP

  - Si3050-FT + Si3019-FT	Voice DAA, SPI control, PCM data
  - Phone Ports "TEL", "LINE"	RJ11, 4P2C (2 pins)

**MAC addresses:**

  MAC address labeled as MAC ADDRESS
  MACs present in both wifi cal data and uboot environment

  eth0.1/phy1	----	*:82	rf 0x4
  phy0		----	*:83	factory 0x4
  eth0.2	MAC	*:b8	"wanaddr"

**Installation:**

  Method 1: Firmware upgrade page:

    (if you cannot access the APs webpage)
    factory reset with the reset button
    connect ethernet to a computer
    OEM webpage at 192.168.0.1
    username and password 'admin'

    Navigate to gear icon, "Device Management", "Tools"
    select the factory.dlf image
    Upload and verify checksum

  Method 2: Serial to upload initramfs:

    Follow directions for TFTP recovery
    upload and boot initramfs and do a sysupgrade

**TFTP recovery:**

  Requires UART serial console, reset button does nothing

  rename initramfs-kernel.bin to 'uImageEPG600'
  make available on TFTP server at 192.168.99.8
  power board, interrupt boot with "4"
  execute `tftpboot` and `bootm` (with the load address)

**Return to OEM:**

  Images from OEM are provided, but not compatible
  with openwrt sysupgrade. So it must be modified.

  Alternatively, back up all mtd partitions before flashing

**Note on switch registers:**

  The necessary registers needed for the QCA8337 switch
  can be read from interrupted boot (tftpboot, bootm)
  by using the following lines in the switch driver ar8327.c
  in the function 'ar8327_hw_config_of'
  where 'qca,ar8327-initvals' is parsed from DTS
  before the new register values are written:

    pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
    pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
    pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
    pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Michael Pratt
6b07d0c077 ramips: mt7620: split gsw hw_init to mac_init, ephy_init
in order for the option ephy-disable to work
without also needing ephy-base option,
we have to skip all the lines that write to mdio addresses that
assume those addresses do not have an external switch.

Otherwise, ephy ports will be disabled in hardware,
but register writes still happen as if they are enabled.

Split the functions so that other things are done first,
and ephy port setup can be skipped with a simple "return".

Tested on Engenius EPG600 (MT7620A ver:2 eco:3)
with QCA8337 external switch

Ref: cc6fd6fbb5 ("ramips: mt7620: add ephy-disable option to switch driver")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Karl Chan
8ef81b4a19 ramips: fix the name of ASUS AX54 because it has dupilcated twice
The name of ASUS AX54 has dupilcated in the DEVICE_ALT0_VENDOR/DEVICE_ALT0_MODEL

Signed-off-by: Karl Chan <exkc@exkc.moe>
2023-02-18 16:01:30 +01:00
Shiji Yang
748f7f1b9c ramips: backport mt7621 PCIs initialization delay patch
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Some devices like ZBT WE1326 and ZBT WF3526-P and some Netgear models need
to delay phy port initialization after calling the mt7621_pcie_init_port()
driver function to get into reliable boots for both warm and hard resets.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-02-18 11:41:54 +02:00
Rodrigo B. de Sousa Martins
77d061167c ramips: Switch default kernel to 5.15
I tested kernel 5.15 on my device for several times without any problems.
In my tests, 5.15 kernel has performance improvements such MGLRU.
Finally, initial kernel 6.1 support is imminent. All ramips subtargets have
5.15 as testing kernel. So, it's time to change.

Tested on my Archer C6 v3.2 (mt7621)

Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
[reformat commit subject and message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2023-02-17 16:31:53 +02:00
Mikhail Zhilkin
51e5f22096 ramips: fix wrong pcie port number for Arcadyan devices
Wrong pcie port number for WLAN causes missing 5g WLAN interface with 5.15
kernel. This changes port from pcie0 to pcie1 in dtsi.

[1.166330] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[1.180073] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[1.193889] mt7621-pci 1e140000.pcie: PCIE1 enabled

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-02-17 16:30:32 +02:00
Karl Chan
92276eef70 ramips: add support for ASUS RT-AX54
Specifications:
- Device: ASUS RT-AX54 (AX1800S/HP,AX54HP)
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x POWER (blue, configurable)
        1x LAN (blue, configurable)
        1x WAN (blue, configurable)
	1x 2.4G (blue, not configurable)
	1x 5G (blue, not configurable)

Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
   Select "2. Upgrade firmware"
   Press enter when show "Run firmware after upgrading? (Y/n):"
   Select 0 for TFTP method
   Input U-Boot's IP address: 192.168.1.1
   Input TFTP server's IP address: 192.168.1.2
   Input IP netmask: 255.255.255.0
   Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"

Signed-off-by: Karl Chan <exkc@exkc.moe>
2023-02-12 18:27:45 +01:00
Felix Baumann
d87482a8db
ramips: fix dts whitespace
Replace blanks with tabs
Remove whitespace from otherwise empty lines

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:52 +01:00
John Audia
64cf31f6ff kernel: bump 5.15 to 5.15.92
All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-08 00:21:28 +01:00
Rosen Penev
2630e5063d treewide: replace wpad-basic-wolfssl default
The newly merged mbedtls backend is smaller and has fewer ABI related
issues than the wolfSSL one.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-04 02:35:03 +01:00
Arınç ÜNAL
5155200f97 ramips: mt7621-dts: fix phy-mode of external phy on GB-PC2
The phy-mode property must be defined on the MAC instead of the PHY. Define
phy-mode under gmac1 which the external phy is connected to.

Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-03 14:11:19 +01:00
Arınç ÜNAL
c6e412378c ramips: mt7621-dts: fix compatible string for mt7530 on TP-Link EAP615-Wall
The correct compatible string for the multi-chip module MT7530 switch in
MT7621AT, MT7621DAT and MT7621ST SoCs is mediatek,mt7621. Remove the
property on TP-Link EAP615-Wall which will default to the said string.

Fixes: a1b8a4d7b3 ("ramips: support TP-Link EAP615-Wall")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-03 13:49:51 +01:00
Jan Hoffmann
c46584ab30 ramips: use on-flash partition table for Sercomm BZV/CHJ
These devices have a partition table stored in flash, which compensates
for any pre-existing bad blocks by enlarging the respective partition.
This means that the current static partition table is only correct for
devices without any bad blocks.

Typical results of this mismatch are degraded wireless performance and
wrong MAC addresses, when the factory partition is shifted due to a bad
block somewhere before it. If there is a bad block already before the
ubi partition, then OpenWrt may not run at all because the kernel can't
find the rootfs.

Use the on-flash partition table to fix these issues. Replace the two
reserved partitions by the full partition list, as the driver does not
allow merging them.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2023-02-03 13:47:04 +01:00
Mark Ceeha
d4c63c7786 ramips: add support for TP-Link Deco M4R v4
This commit adds support for the V4 hardware revision of the Deco M4R.
V4 is a complete overhaul of the hardware compared to V1 and V2,
and is much more similar to the Archer C6 V3 and C6U V1.

Specifications:

  SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads)
  RAM: Kingston D1216ECMDXGJD (256 MB)
  Wireless 2.4 GHz: MediaTek MT7603EN
  Wireless 5 GHz: MediaTek MT7613BEN
  Flash: 16 MB SPI NOR

Installation:

Flash the *-factory.bin image in the U-Boot recovery webserver.
You can trigger this webserver by holding the reset button until the LED
flashes yellow, or by hooking up to serial pads on the board (clearly
labeled GND, RX and TX) and pressing `x` early in boot.

Once the factory image has been flashed, you can use the regular upgrade
procedure with sysupgrade images for subsequent flashes.

Signed-off-by: Mark Ceeha <hi@shiz.me>
Tested-by: Mark Ceeha <hi@shiz.me>
2023-02-03 12:13:50 +01:00
Dmitry Sokolov
39e4f03fd3 ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2
Device is the same as Xiaomi Mi Router 4A Gigabit, except of:
- 5G WiFi is MT7663
- addresses of leds, wifi and eth ports are slightly changed

Specs:
  SoC:  MT7621
  CPU:  2 x 880 MHz
  ROM:  16 MB
  RAM:  128 MB
  WLAN: MT7603, MT7663

MAC addresses:
  WAN     ****  factory 0xe006 (label)
  LAN     *:f7  factory 0xe000
  2.4 GHz *:f8  factory 0x0000+0x4 (mtd-eeprom+0x4)
  5 GHz   *:f9  factory 0x8000+0x4 (mtd-eeprom+0x4)

Installation:

Factory firmware is based on a custom OpenWrt 17.x.
Installation is the same as for Xiaomi Mi Router 4A Gigabit.

Probably the easiest way to install is to use the script from
this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155

In a more advanced case, you can do everything yourself:
- gain access to the device through one of the exploits described
  in the link above
- upload sysupgrade image to /tmp
- overwrite stock firmware:
  # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1

Recovery:

Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit.
Possible options can be found here:
https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition

One of the ways is to use another router with OpenWrt:
- connect both routers by their LAN ports
- download stock firmware from [1]
- place it inside /tmp/test.bin on the main router
- configure PXE/TFTP on the main router
- power off 4Av2, hold Reset button, power on
- as soon as image download via TFTP starts, Reset can be released
- blinking blue wan LED will indicate the end of the flashing process,
  now router can be rebooted
[1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin

Signed-off-by: Dmitry Sokolov <e323w@proton.me>
2023-01-28 22:11:44 +01:00
Maxim Anisimov
3690c4a092 ramips: improve support for Zyxel Keenetic Extra II
- drop unneeded default-state for led_power
- concat firmware partitions to extend available free space
- increase spi flash frequency to 32 Mhz (value from stock firmware bootlog)
- drop broken-flash-reset because of onboard flash chip W25Q256FV has reset support
- add compatible for pcie wifi according to kernel documetation
- switch to wan mac address with offset 0x28 in rf-eeprom

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-28 21:45:34 +01:00
Maxim Anisimov
2fe29794b1 ramips: use hex value in zyimage command for Keenetic KN-3010
This is cosmetic change. The hex value is related to the device
model and more human friendly.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-28 21:40:37 +01:00
Nikolay Martynov
62dbcb8305 ramips: Fix root volume for tplink-er605-v2
This device has two sets of volumes: main ones (`kernel`, `rootfs`, etc) and
'backup' (`kernel.b`, `rootfs.b`, etc). Bootloader tries to determine which set of
volumes to use by looking at contens of `extra-para` and `extra-para.b` volumes.
These volumes contain JSON that looks like this:

```
{
	"dbootFlag": "1",
	"integerFlag": "1",
	"fwFlag": "GOOD",
	"score":1
}
```

It looks like the bootloader looks for `"fwFlag": "GOOD"` (as opposed to `BAD`)
then it compares `score` field - whichever 'good' volume has bigger score wins.
This determines which set of volumes to use to boot.

So for example if `extra-para` is good and has bigger score then `kernel`,
`rootfs`, etc volumes are used. This means bootloader needs to explain to the
kernel which volume to use for the rootfs. After looking at bootloader code with
disassembler I think it contains a bug. Relevant part of code looks something
like this:

```
  if (image_id == 0) {
    rootfs_volume_id = 8;
    rootfs_volume_name = "rootfs";
  }
  else {
    rootfs_volume_id = 0xf;
    rootfs_volume_name = "rootfs.b";
  }
  sprintf(
    &buffer,
    0x800,
    "console=ttyS0,115200 noinitrd ubi.mtd=3,2048 ubi.block=0,%s
    root=/dev/ubiblock0_%d DKMGT_IMAGE_ID=%d DKMGT_IMAGE_TYPE=ubi",
    rootfs_volume_name,
    rootfs_volume_id,
    image_id
    );
```

Where `image_id == 0` if 'normal' (not '*.b' set of volumes is used).
However from device dumps we know that from the factory `rootfs.b` has id 8 and
`rootfs` has id 15.

So from above we can see that ids and names of rootfs volumes do not match. More
over - they are hardcoded in the bootloader.

Both things are problematic for OpwnWRT which completely removes volumes on
update meaning that volume ids may actually change.

So instead of relying on bootloader to provide the kernel with root device this
patch forces kernel to determine root automatically - and it defaults to
`rootfs` volume which is correct for our purposes.

Overall this makes image boot fine from flash after sysupgrade from inirams.
assuming `extra-para*` volumes make bootloader use non-'*.b' set of volumes.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
2023-01-22 14:37:47 +01:00
Harm Berntsen
09f313bfd7 ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.

Specifications
--------------
SOC   : Mediatek MT7621AT
ETH   : Two 1 gigabit ports, built into the SOC
WIFI  : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED   : Power (green+red)
LED   : WiFi (green+blue)
LED   : WPS (green+red)
LED   : Followme (green+red)
Power : 12 VDC, 1A barrel plug

Winbond variant:
RAM   : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1

Macronix variant:
RAM   : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec  4 2017 - 11:37:57), Ralink 5.0.0.1

Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.

The pinout is: VCC (the square), RX, TX, GND.

Installation
------------
See the Wiki page [1] for more details, it comes down to:

1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
   connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
   environment located at 0x30000

Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.

MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use      | address          | example           |
+----------+------------------+-------------------+
| Device   | label            | 00:00:00:11:00:00 |
| Ethernet | + 3              | 00:00:00:11:00:03 |
| 2g       | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g       | + 1              | 00:00:00:11:00:01 |
+----------+------------------+-------------------+

The label address is stored in ASCII in the board_data partition

Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
  both partitions for more storage space.

Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
  macaddr_add
- Only the power LED is configured by default

References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653

Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
2023-01-15 13:41:02 +01:00
John Audia
2835df54ab kernel: bump 5.10 to 5.10.163
Removed upstreamed:
  generic/101-Use-stddefs.h-instead-of-compiler.h.patch[1]

All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.163&id=ddd2bb08bd99b7ee4442fbbe0f9b80236fdd71d2

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-14 22:31:38 +01:00
Filip Milivojevic
990419dac3 ramips: cudy wr1300v1 reduce SPI freq to 10000000
Reducing SPI flash frequency allows the build to boot on both old variants
with W25Q128 chip and new variants with XM25QH128C chip.

The old 80000000 value only boots on devices with the W25Q128 flash.

This is also the change Cudy themselves made in their openwrt builds and
their .dts file.

Removed m25p,fast-read as it is not needed with slower speeds.

Signed-off-by: Filip Milivojevic <zekica@gmail.com>
2023-01-14 19:25:06 +01:00
Keith Harrison
c13263ca07 ramips: add support for D-Link DIR-1935 A1
Add support for D-Link DIR-1935 A1 based on similarities to DIR-882 A1,
DIR-867 A1 and other DIR-8xx A1 models. Existing DIR-882 A1 openwrt
"factory" firmware installs without modificaitons via the D-Link
Recovery GUI and has no known incompatibilities with the DIR-1935 A1.

Changes to be committed:
       new file:   target/linux/ramips/dts/mt7621_dlink_dir-1935-a1.dts
       modified:   target/linux/ramips/image/mt7621.mk
       modified:   target/linux/ramips/mt7621/base-files/etc/board.d/01_leds

Specifications:
* Board: Not known
* SoC: MediaTek MT7621 Family
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615 Family (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
        WiFi 5G (green)

Notes:
* 160MHz 5GHz is available in LuCi but does not appear to work (i.e. no
  SSID is visible in wifi scanning apps on other devices) with either
  official DIR-882 A1 firmware or a test build for the DIR-1935 A1 based
  on the 22.03.2 branch. 80 MHz 5GHz works.

Serial port:
* Untested (potential user damage/error)
* Expected to be identical to other DIR-8xx A1 models:
	* Parameters: 57600, 8N1
	* Location: J1 header (close to the Reset, WiFi and WPS buttons)
	* Pinout: 1 - VCC
		  2 - RXD
	          3 - TXD
		  4 - GND

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

Signed-off-by: Keith Harrison <keithh@protonmail.com>
2023-01-14 19:09:56 +01:00
Felix Baumann
acd3b5e83b ramips: Alternative name Asus RT-AX1800U for Asus RT-AX53U
The Asus RT-AX1800U is identical to the already supported Asus RT-AX53U.
Use the ALT0 buildroot tags to show both devices.

Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-01-14 19:05:41 +01:00
Jo Deisenhofer
f204c812e9 ramips: add support for xiaomi RA75 Range Extender
This device is a 'Range extender' variant of the Xiaomi 4A router.
Its identical to the 100m non-intl/chinese version as much as it can run
the same firmware, differences being form factor, LEDs, WPS button
and one 100M port only.
The stock firmware differs significantly, being 'app managed only'.

Device specification
--------------------
SoC:      MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi:     MT7612EN 5G-ac 80MHz 2T2R
Flash:    16MB W25Q128BV
DRAM:     64MB built-in SoC
Switch:   built-in SoC
Ethernet: 1x10/100 Mbps
USB:      None
Antennas: 2 x external, non-detachable
LEDs:     2 programmable blue/amber
Buttons:  WPS and reset (hidden)
Housing:  Range Extender / Wall wart
Serial:   115200,8n1

MAC Addresses
-------------
All 3 MACs are read from flash and identical to stock.
Label MAC is WIFI 2G

Installation
------------
No HTML UI on this device, serial console only. The serial connector
is unpopulated but standard size and clearly marked. Flash from the
U-Boot shell at boot by choosing (2) and flashing the sysupgrade file
via tftp.

Recovery/Debricking procedures of the xiaomi 4A and variants should
work, but there currently is no official source for the stock firmware.

Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
2023-01-14 19:02:21 +01:00
Jo Deisenhofer
ab402f3d23 ramips: Move LED definition out of included dtsi into dts
Prepare for a new target with different led definitions that wants to
include this dtsi. The resulting dtb are unchanged, verified with dtdiff

Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
2023-01-14 19:02:20 +01:00
Mikhail Zhilkin
1a35edfbdb ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |              J2
    |
    +--- Don't connect

Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
   with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 't'
3. Load and run OpenWrt initramfs image:
      tftpboot
      bootm
4. Once inside OpenWrt, switch to the first boot image:
      fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Back to Stock
-------------
1. Run in the OpenWrt shell:
      fw_setenv BootImage 1
      reboot

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
   the OEM firmware

MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
|         | MAC example 1     | MAC example 2     | Algorithm   |
+---------+-------------------+-------------------+-------------+
| label   | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| LAN     | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WAN     | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2     |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).

Notes
-----
[1] WAN MAC address:
   a. First octet of WAN MAC is differ than others and OUI is not related
      to TP-Link company. This probably should be fixed.
   b. Flipping bits in first octet and hex delta are different for the
      different MAC examples:
      +-----------------+----------------+----------------+
      |                 | Example 1      | Example 2      |
      +-----------------+----------------+----------------+
      | LAN             | 68 = 0110 1000 | 50 = 0101 0000 |
      | MAC (1st octet) |         ^ ^ ^  |                |
      +-----------------+----------------+----------------+
      | WAN             | 72 = 0111 0010 | 54 = 0101 0100 |
      | MAC (1st octet) |         ^ ^ ^  |            ^   |
      +-----------------+----------------+----------------+
      | HEX delta       | 0xa            | 0x4            |
      +-----------------+----------------+----------------+
      | DEC delta       | 4              | 4              |
      +-----------------+----------------+----------------+
   c. DEC delta is a constant (4). This looks like a mistake in OEM
      firmware and probably should be fixed.
   Based on the above, I decided to keep correct OUI and make WAN MAC =
   label + 1.

[2] Bootloaders
   The device contains 3 bootloaders:
   - First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
     located on NAND Flash to load next full-feature Uboot.
   - Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
     bootloader includes recovery webserver. Requires special uImages to
     continue the boot process:
        0x00 (os0, os1) - firmware uImage
        0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
   - Additionally, both slots of the original TP-Link firmware contains
     Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
     magics and CRCs. We don't use this U-Boot with OpenWrt.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-14 18:36:33 +01:00
INAGAKI Hiroshi
1f5f2e588a ramips: add support for ELECOM WRC-2533GHBK2-T
ELECOM WRC-2533GHBK2-T is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC      : MediaTek MT7621A
- RAM      : DDR3 128 MiB
- Flash    : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN     : 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
  - Switch : MediaTek MT7530 (SoC)
- LED/keys : 4x/3x (2x buttons, 1x slide-switch)
- UART     : through-hole on PCB
  - J4: 3.3V, RX, GND, TX from SoC side
  - 57600n8
- Power    : 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-2533GHBK2-T normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

MAC addresses:

LAN    : BC:5C:4C:xx:xx:FD (Config,  "ethaddr" (text))
WAN    : BC:5C:4C:xx:xx:FC (Config,  "wanaddr" (text), Label)
2.4 GHz: BC:5C:4C:xx:xx:FE (Factory, 0x4       (hex))
5 GHz  : BC:5C:4C:xx:xx:FF (Factory, 0x8004    (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-14 15:41:00 +01:00
INAGAKI Hiroshi
9fe648166e ramips: separate and update dtsi of ELECOM WRC-2533GHBK-I/GHBK2-T
ELECOM WRC-2533GHBK2-T has the almost same hardware as WRC-2533GHBK-I,
so separate the common parts from dts to dtsi.
Additionaly, add color/function properties to LED nodes and change the
trigger of wlan2g/wlan5g LED to "phy*tpt" trigger.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-14 15:41:00 +01:00
John Audia
843e3dace7 kernel: bump 5.15 to 5.15.87
Removed upstreamed:
  generic/hack-5.15/290-net-dsa-mv88e6xxx-depend-on-PTP-conditionally.patch[1]

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.87&id=945e58bdaf6faf6e3f957d182244fa830acddab4

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-13 22:04:22 +01:00
Arınç ÜNAL
fc33c41c21 ramips: do not use GPIO function on switch pins on certain devices
The pins of the MT7530 switch that translate to GPIO 0, 3, 6, 9 and 12 has
got a function, by default, which does the same thing as the netdev
trigger. Because of bridge offloading on DSA, the netdev trigger won't see
the frames between the switch ports whilst the default function will.

Do not use the GPIO function on switch pins on devices that fall under this
category.

Keep it for:

mt7621_belkin_rt1800.dts: There's only one LED which is for the wan
interface and there's no bridge offloading between the "wan" interface and
other interfaces.

mt7621_yuncore_ax820.dts: There's no bridge offloading between the "wan"
and "lan" interfaces.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-01-08 12:31:52 +08:00
Sebastian Schaper
3c31f6b521 ramips: add support for D-Link DAP-X1860 A1
The DAP-X1860 is a wall-plug AX1800 repeater.

Specifications:
- MT7621, 256 MiB RAM, 128 MiB SPI NAND
- MT7915 + MT7975 2x2 802.11ax (DBDC)
- Ethernet: 1 port 10/100/1000
- LED RSSI bargraph (2x green, 1x red/orange), status
  and RSSI LEDs are incorrectly populated red/orange
  (should be red/green according to documentation)

Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
- Upload factory.bin, confirm flashing
  (seems to work best with Chromium-based browsers)

Revert to OEM firmware:
- tar -xvf DAP-X1860_RevA_Firmware_101b94.bin
- openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \
  -out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ==
- tar -xvf FWImage.st1
- flash kernel_DAP-X1860.bin via Recovery

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2023-01-07 17:56:10 +01:00
Shiji Yang
9a07895729 mt76: add stand-alone MT7622 firmware package
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
fc9dd3f083 mt76: add stand-alone MT7915 firmware package
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
3dbaf89296 ramips: use default lzma dictionary size for better performance
limit dictionary size patch was introduced to solve the well known
"LZMA ERROR 1 - must RESET board to recover" error.
09b6755946 "ramips: limit dictionary size for lzma compression"

It seems that it has failed recently and we can use lzma loader to fix
this error by adding "$(Device/uimage-lzma-loader)". So just remove it
to use the default parameter -d24 for a higher compression ratio.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 16:56:16 +01:00
David Bauer
8036fb8dd0 ramips: combine USW-Flex dual firmware-partitions
In order to maximize the available space on USW-Flex boards using a
dual-image partition layout, combine the two OS partitions into a single
partition.

This allows users to access more usable space for additional packages.

Don't limit the usable image size to the size of a single OS partition.
The initial installation has to be done with an older version of OpenWrt
in case the generated image exceeds the space of a single kernel
partition in the future.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-07 01:32:58 +01:00
Leon M. Busch-George
f6d394e9f2 ramips: add support for Cudy M1800
Specifications

  SoC:       MT7621
  CPU:       880 MHz
  Flash:     32 MiB
  RAM:       256 MiB
  WLAN:      MT7915 WiFi 6 (2.4/5 GHz)
  Ethernet:  2x Gbit ports

                  MAC
LAN        b4:4b:d6:2e:c7:b0 (label)
WAN        b4:4b:d6:2e:c7:b1
WiFi 2.4   00:0c:43:26:46:08
WiFi 5     00:0c:43:26:59:97

Installation

There are two known options:
1) The Luci-based UI.
2) Press and hold the reset button during power up.
   The router will request 'recovery.bin' from a TFTP server at
   192.168.1.88.

Both options require a signed firmware binary.
The openwrt image supplied by cudy is signed and can be used to
install unsigned images.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2023-01-06 19:22:52 +01:00
Maxim Anisimov
dbebfb88b5 ramips: add support for Keenetic KN-1613
Keenetic KN-1613 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7628AN.

Specification:
- System-On-Chip: MT7628AN
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 4x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): SoC Built-in 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-keenetic_kn-1613-squashfs-factory.bin"
   to "KN-1613_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-06 17:53:10 +01:00
Maxim Anisimov
4eeecf41cf ramips: enable mtd virtual concat support for mt76x8 subtarget
This is required for upcoming Keenetic KN-1613 support

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-06 17:53:10 +01:00
Vincent Tremblay
2fab942ce1 generic: fix silicon labs spidev bindings
Fix Silicon Labs bindings in the spidev driver

Some bindings for Silicon Labs chips already exists upstream.
These bindings can be found in trivial-devices.yaml.

The existing bindings are using "silabs" instead of "siliconlabs" to
identify the manufacturer.

This commit add two submitted patches for silabs chips and rename the
manufacturer in the different DTS for more coherence.

Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2023-01-06 16:01:10 +01:00
Ignas Poklad
7801e814dd ramips: add Unielec U7621-06 32M build target
Add 32M build target

Rest of the details as per commit 46ab81e405 ("ramips add support for
UniElec U7621-06")

Signed-off-by: Ignas Poklad <ignas2526@gmail.com>
2023-01-05 00:10:14 +01:00
Shiji Yang
6760c7cbe5 ramips: enable Wi-Fi LED support for Afoundry EW1200
Add LED properties to PCIe node to enable Wi-Fi LED support.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-04 23:32:27 +01:00
Shiji Yang
0eefea2ed7 ramips: enable Wi-Fi LED support for Zbtlink ZBT-WE1326
Add LED properties to PCIe node to enable Wi-Fi LED support.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-04 23:32:27 +01:00
Nikolay Martynov
665c2154ef ramips: add basic support for tp-link er605-v2
This is a MT7621-based device with 128MB NAND flash, 256MB RAM, and a USB port.
The board has headers to attach console. In order for them to work two solder
bridges near those pads need to be made.

The defice has the following partition table:

```
0x000000000000-0x000000080000 : "u-boot"
0x000000080000-0x000000100000 : "u-boot-env"
0x000000100000-0x000000140000 : "factory"
0x000000140000-0x000007e00000 : "firmware"
0x000007e00000-0x000008000000 : "panic-ops"
```

`firmware` partition contains UBI volumes. Unfortunately I accidentally wiped
partition and I no longer have access to it.

`firmware` partition contains 'secondary' U-Boot which is run by 'first' u-boot.
It also contains various configuration partitions that include device info and
MAC address. There also seems to be 'primary' and 'backup' set of 'main' volumes.

U-boot has `mtkupgrade` command that just overrides data on firmware partitions.
Firmware file provided by TP-Link cannot be used with that command.

U-boot also has 'recovery' http server. Unfortunately I was not able to make it
work with manufacturer's firmware.

Manufacturer's firmware essentially contains multiple UBI volumes along with
'partition table'. Unfortunately I no longer can properly run manufacturer's
firmware so I cannot at the moment try to a support for building 'factory' images.

This patch adds support for initramfs image as well as sysupgrade image.

This seems to be pretty standard MT7621 board otherwise.

Things that work:
* network
* leds
* usb
* factory MAC detection

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
2023-01-04 23:19:19 +01:00
Marian Sarcinschi
c4b806d5c4 ramips: add missing LEDs to Asus RT-AX53U
This patch adds the missing LEDs to Asus RT-AX53U.
Based on PR #10400 and patch provided in #11068
 - enable the two LEDs controlled by mt7915e for wireless;
 - add label to power LED so it works properly and fix formatting;
 - add the USB LED;
 - switch LEDs are best left to be controlled by hardware for now.

Co-Authored-By: Ivan Rozhuk <rozhuk.im@gmail.com>
Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Co-Authored-By: Hartmut Birr <e9hack@gmail.com>
Tested-by: Felix Baumann <felix.bau@gmx.de>
Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Marian Sarcinschi <znevna@gmail.com>
2023-01-04 21:56:49 +01:00
John Audia
738b04c881 kernel: bump 5.15 to 5.15.86
Removed upstreamed:
  pending-5.15/101-Use-stddefs.h-instead-of-compiler.h.patch[1]
  ipq806x/patches-5.15/122-01-clk-qcom-clk-krait-fix-wrong-div2-functions.patch[2]
  bcm27xx/patches-5.15/950-0198-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch[3]

Manually rebased:
  ramips/patches-5.15/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch[4]

Added patch/backported:
  ramips/patches-5.15/107-PCI-mt7621-Add-sentinel-to-quirks-table.patch[5]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=c160505c9b574b346031fdf2c649d19e7939ca11
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=a051e10bfc6906d29dae7a31f0773f2702edfe1b
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=ec1727f89ecd6f2252c0c75e200058819f7ce47a
4. Quilt gave this output when I applied the patch to rebase it:
% quilt push -f
Applying patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch
patching file arch/mips/ralink/Kconfig
patching file drivers/pci/controller/Kconfig
patching file drivers/pci/controller/Makefile
patching file drivers/staging/Kconfig
patching file drivers/staging/Makefile
patching file drivers/staging/mt7621-pci/Kconfig
patching file drivers/staging/mt7621-pci/Makefile
patching file drivers/staging/mt7621-pci/TODO
patching file drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
patching file drivers/staging/mt7621-pci/pci-mt7621.c
Hunk #1 FAILED at 1.
Not deleting file drivers/staging/mt7621-pci/pci-mt7621.c as content differs from patch
1 out of 1 hunk FAILED -- saving rejects to file drivers/staging/mt7621-pci/pci-mt7621.c.rej
patching file drivers/pci/controller/pcie-mt7621.c
Applied patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch (forced; needs refresh)

Upon inspecting drivers/staging/mt7621-pci/pci-mt7621.c.rej, it seems that
the original patch wants to delete drivers/staging/mt7621-pci/pci-mt7621.c
but upstream's version was not an exact match.  I opted to delete that
file.

5. Suggestion by hauke: 19098934f9
"This patch is in upstream kernel, but it was backported to the old
staging driver in kernel 5.15."

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-03 23:55:45 +01:00
INAGAKI Hiroshi
ef4e1ae18d ramips: enable BBT on NAND in I-O DATA devices
This patch enables MediaTek NAND BBT on I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.).

[WN-AX2033GR]
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[WN-AX1167GR2, WN-DX1167R, WN-DX1200GR, WN-DX2033GR]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-30 16:12:15 +08:00
Hauke Mehrtens
7272203022 ramips: Refresh patches
The patch was not applying cleanly any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-29 19:01:15 +01:00
Felix Baumann
3f1e9f6f3b
ramips: add support for read/write uboot env to Asus RX-AX53U
Add support for read/writing uboot env by renaming the second partition
to its stock label "nvram" and remove the deemed unnecessary
"read-only". Split the first partition "u-boot" in two, in order
to allow `fw_setenv` safe write-access to the uboot environment
variables.

This implements hauke's request from [1].
Based on the patch provided by Shiji Yang.

[1] https://github.com/openwrt/openwrt/pull/10400#discussion_r945153224

Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description, fix some whitespace problem ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-28 14:04:57 +01:00
Hauke Mehrtens
376eb2d924 ramips: Fix drivers/pwm/pwm-mediatek-ramips.c compile
The pwmchip_remove() function returns void now. Fix a compile problem in
the drivers/pwm/pwm-mediatek-ramips.c driver.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-23 00:43:39 +01:00
Hauke Mehrtens
92eb787d08 kernel: Move CONFIG_PWM_IMG and CONFIG_PWM_MEDIATEK to generic configuration
In the build of the ramips/mt76x8 target the user gets asked about these
two configuration options, add them to the generic kernel configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-23 00:43:33 +01:00
Julien Dusser
b893aa7992 ramips: add support for Linksys E5400 and clones
Linksys E5400 is a 2.4/5GHz dual band AC router, based on MediaTek
MT7628AN. This device is also sold as Linksys E2500v4, E5300 and E5350
with the same hardware, but software speed limitations in vendor
firmwares.

Specification:
 * SoC: MT7628AN (580 MHz)
 * RAM: DDR2 64 MiB
 * Flash: 16 MiB NOR (W25Q128BV)
 * Wi-Fi:
   * 2.4GHz: SoC Built-in
   * 5GHz: MT7612EN
 * Ethernet: 5x 100Mbps
   * Switch: SoC built-in
 * UART:
   * 115200, 8N1, 3.3V (real u-boot speed: 119050)
   * Pinout JB4: 1:[3V3] (TXD) (RXD) [NC] (GND)

Flash Layout:
  0x0000000-0x0030000 : "Bootloader"
  0x0030000-0x0040000 : "Config"
  0x0040000-0x0050000 : "Factory"
  0x0050000-0x0ff0000 : "Kernel"
  0x0ff0000-0x1000000 : "CBTinfo"

MAC address:
  LAN: factory 0x28
  WAN: LAN + 1
  2.4G: LAN + 2
  5G: LAN + 3

Installation:
1. Connect to UART, use LF as EOL (not CRLF)
2. Set IP address
  - Press 4 during boot
  - setenv serverip <TFTPSERVER_IP>
  - setenv ipaddr <DEVICE_IP>
  - setenv bootfile openwrt-ramips-mt76x8-linksys_e5400-initramfs-kernel.bin
  - saveenv
  - reset
3. Load Openwrt Kernel image from TFTP:
  - Press 1 during boot
  - IP and filename should be already set
4. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2022-12-18 21:24:57 +01:00
Alexey Bartenev
3f201d1f8e ramips: add support for SNR-CPE-W4N-MT router
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A

Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
 "Administration/Management/Firmware update/Choose File" in vendor's
 web interface (ip: 192.168.1.10, login: Admin, password: Admin).
 Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 file by "System/Backup/Flash Firmware/Flash image..." in
 LuCI web interface (ip: 192.168.1.1, login: root, no password).
 Wait ~240 seconds.

Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
 Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
 Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
 new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2022-12-17 22:34:44 +01:00
Shiji Yang
6361a952af ramips: improve support for SIM SIMAX1800T and Haier HAR-20S2U1
1. Use ARTIFACTS to build factory image. This change allows users to
   generate initramfs factory image using OpenWrt ImageBuilder.

2. Override the default bootargs property defined in "mt7621.dtsi".
   Although we use the "bootargs-override" property to set bootargs,
   the default "bootargs" property will still be written into the
   device tree, so it is better to override it.

Tested on SIM SIMAX1800T

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-17 21:08:14 +01:00
Shiji Yang
a7d8b54f86 ramips: improve support for H3C TX180x series devices
1. Explicitly declare gpio pin groups to ensure that gpio works properly.

2. Override bootargs in device tree to avoid modifying u-boot envs during
   initial installation.

Tested on H3C TX1801 Plus

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-17 21:08:14 +01:00
Mikhail Zhilkin
0ec8d991c2 ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1.  Login to the router web interface under admin account
2.  Navigate to Settings -> Configuration -> Save to Computer
3.  Decode the configuration. For example, using cfgtool.py tool (see
    related section):
       cfgtool.py -u configurationBackup.cfg
4.  Open configurationBackup.xml and find the following line:
    <PARAMETER name="Password" type="string" value="<your router serial \
       is here>" writable="1" encryption="1" password="1"/>
5.  Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6.  Encode the configuration. For example, using cfgtool.py tool:
       cfgtool.py -p configurationBackup.xml
7.  Upload the changed configuration (configurationBackup_changed.cfg) to
    the router
8.  Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
    ETxxxxxxxxxx is the serial number from the backplate label)
9.  Navigate to Settings -> WAN -> Add static IP interface (e.g.
    10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
    10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
    ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
       sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
       printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
       reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
      cd /tmp
      for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
      tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
      tftp -l mtd.md5 -p 10.0.0.2

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | *:50    |
| WAN | label + 11 | *:5b    |
| 2g  | label + 2  | *:52    |
| 5g  | label + 3  | *:53    |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000

cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker

Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-12-13 23:06:20 +01:00
John Audia
7b7d8fe60d kernel: bump 5.10 to 5.10.157
Manually rebased:
	backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch
	hack-5.10/645-netfilter-connmark-introduce-set-dscpmark.patch

Removed upstreamed:
	pending-5.10/706-netfilter-nf_flow_table-add-missing-locking.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.157&id=b8e494240e69f91517256adcd6fda62d0671772d

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00
John Audia
68426e54ed kernel: bump 5.15 to 5.15.82
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:42:52 +01:00
John Audia
424210b7be kernel: bump 5.15 to 5.15.81
Manually rebased:
	backport-5.15/715-v6.0-net-ethernet-mtk_eth_soc-add-the-capability-to-run-m.patch
	hack-5.15/645-netfilter-connmark-introduce-set-dscpmark.patch[1]

Removed upstreamed:
	pending-5.15/701-netfilter-nf_flow_table-add-missing-locking.patch[2]

All other patches automatically rebased

1. Rebase by Kevin 'ldir' Darbyshire-Bryant<ldir@darbyshire-bryant.me.uk>
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.81&id=8db9e60cdfdae5b049e32e82323da8f0f989066a

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:42:52 +01:00
Jan-Niklas Burfeind
dce66899bf ramips: add support for Wavlink WS-WN572HP3 4G
Wavlink WS-WN572HP3 4G is an 802.11ac
dual-band outdoor router with LTE support.

Specifications;
* Soc: MT7621DAT
* RAM: 128MiB
* Flash: NOR 16MiB GD-25Q128ESIG3
* Wi-Fi:
  * MT7613BEN: 5GHz
  * MT7603EN: 2.4GHz
* Ethernet: 2x 1GbE
* USB: None - only used internally
* LTE Modem: Quectel EC200T-EU
* UART: 115200 baud
* LEDs:
  * 7 blue at the front
    * 1 Power
    * 2 LAN / WAN
    * 1 Status
    * 3 RSSI (annotated 4G)
  * 1 green at the bottom (4G LED)
* Buttons: 1 reset button

Installation:
* press and hold the reset button while powering on the device
* keep it pressed for ten seconds
* connect to 192.168.10.1 via webbrowser (chromium/chrome works, at
  least Firefox 106.0.3 does not)
* upload the sysupgrade image, confirm the checksum, wait 2 minutes
  until the device reboots

Revert to stock firmware:
* same as installation but use the recovery image for WL-WN572HP3

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-12-07 12:30:45 +01:00
David Bauer
bc14925f3d ramips: define loadaddr for all UniFi devices
Define the load-address for the DTB of all Ubiquiti UniFi devices using
FIT images. From the GPL code we can assume these boards are affected by
the same relocating issue with the vendor bootloader.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-12-07 12:30:29 +01:00
Joonhyuk Song
25ede5170d ramips: mt7621: enable lzma-loader for netis WF2881
Fixes boot loader LZMA decompression issues (LZMA ERROR 1)

Signed-off-by: Joonhyuk Song <thenoface303@gmail.com>
2022-12-06 01:51:00 +01:00
John Thomson
7ea965b578 ramips: mt7621: mikrotik 760igs (hEX S) fix SFP
This device uses an AR8031/AR8033 chip to convert SoC gmac1
RGMII to 1000base-x or sgmii for the SFP fibre cage.
The SFP cage requires phy-mode rgmii-rxid, and without it will not
recieve any packets: ethtool -S sfp rx_fcs_errors will increase when
packets should be being received, but no other _rx counters will change.

Fixes: c77858aa79 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2022-12-06 01:47:36 +01:00
INAGAKI Hiroshi
a224412bbc ramips: use ARTIFACTS for initramfs-factory of I-O DATA WN-AX1167GR
Use ARTIFACTS to generate initramfs-based factory image of I-O DATA
WN-AX1167GR instead of redundant recipe which generate on
KERNEL_INITRAMFS.

Note:

WN-AX1167GR has 2x OS images on stock firmware.

stock log:

flash manufacture id: c2, device id 20 18
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"

1st image is "Kernel" and 2nd is "app" when booted from 1st image.
In OpenWrt, those 2x partitions are combined to "firmware" with
undefined (empty) areas (0x7e0000-0x7fffff, 0xf80000-0xf8ffff).

The size of an OS image partition is 0x780000 (7680 KiB = 7.5 MiB), so
check-size for initramfs-factory image needs to be called with the size.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-05 01:28:28 +00:00
Senis John
a8f3c97ce8 ramips: add support for HiWiFi HC5611
CPU: MediaTek MT7628AN @ 575 MHz
Flash: 16 MB
RAM: 128 MB
Ethernet: 10/100Mbps x 1
Wlan: 300 Mbps
USB: USB 2.0 x 1
LED: red/green x 1
Button: reset x 1

1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh
2. Upload the openwrt firmware to the router via SCP
3. Login the router via SSH
4. Run `mtd -r write path_to_firmware.bin firmware`

I have tested on my device.
- The LED will display RED on power-on, After system start completed, trun GREEN
- Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device
- USB can working under official u-boot

Signed-off-by: Senis John <thank243@gmail.com>
2022-12-04 15:21:12 +08:00
Bjørn Mork
8719f73fa2 ramips: mt7621: enable lzma-loader for ZyXEL WAP6805
Fixing "Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board
to recover".

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2022-12-03 21:04:38 +01:00
Felix Fietkau
3dff6b53db kernel: fix mtk_eth_soc issue when using secondary GMAC on MT7621/MT7622
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break

Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-25 01:56:53 +01:00
Maxim Anisimov
21762e4653 ramips: add support for Keenetic KN-3010
Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT.

Specification:
- System-On-Chip: MT7621DAT
- CPU/Speed: 880 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100/1000 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin"
   to "KN-3010_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2022-11-20 16:44:24 +01:00
Moritz Warning
c0fb12c42e treewide: uniform vendor name for ASUS
Their own website (https://www.asus.com)
always uses the upper case style name.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2022-11-16 23:30:11 +01:00
Ivaylo Ivanov
6afc355b2e ramips: Add support for D-Link DIR-3060 A1
Hardware specification:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HVSINA 128MB
RAM: Micron MT41K128M16JT-125 256MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7615DN 2.4GHz N 2x2:2
WiFi2: MT7615DN 5GHz AC 2x2:2
WiFi3: MT7615N 5GHz AC 4x4:4
Button: WPS, Reset

Flash instructions:
OpenWrt can be installed via D-Link Recovery GUI:

    Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
    Give it ~30 seconds, to boot the recovery mode GUI
    Connect your client computer to LAN1 of the device
    Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
    Call the recovery page for the device at http://192.168.0.1/
    Use the provided emergency web GUI to upload and flash a new firmware to the device

Signed-off-by: Ivaylo Ivanov <iivailo@mail.bg>
2022-11-13 22:36:06 +01:00
Daniel Fuchs
794d1645b3 ramips: add support for Amped Wireless B1200EX
This device is almost identical to the already supported Edimax
EW-7476RP5, the only differences are:
- There is no mode selection slider switch on this device
- The two wireless LEDs are green instead of blue
- Model name in the CSYS header is RN10

Additional changes:
- Moved WiFi LEDs and the slider switch to the individual dt files
- Added ieee80211-freq-limit to the mt7612e radio to properly disable
  2.4GHz band on this radio

Device specifications:
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS/RESET
LED:	- WiFi 5G (green)
	- WiFi 2.4G (green)
	- Signal Strength (green)
	- Power (green)
	- WPS (green)
	- LAN (green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the WPS button
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation:
Upload the sysupgrade image via the default web interface

Signed-off-by: Daniel Fuchs <software@sagacioussuricata.com>
2022-11-13 22:36:06 +01:00
Mikhail Zhilkin
0cfd15552e ramips: add support for Rostelecom RT-SF-1
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
   Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
   firmware
6. Update firmware using web interface with the OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
    printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+------------+
| use | address    | example    |
+-----+------------+------------+
| LAN | label      | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g  | label + 2  | *:74, *:d4 |
| 5g  | label + 3  | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-13 21:51:22 +01:00
Mikhail Zhilkin
e6b99a4e43 ramips: create common dtsi for Sercomm Dxx routers
This commit adds common dtsi for the following Sercomm devices with 256
MB NAND:
Beeline Smartbox TURBO (Sercomm DF3)
Rostelecom RT-SF-1 (Sercomm DKG)

Also fixed typo ("Container" mtd name should be with a capital).

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-13 21:51:22 +01:00
Martin Dziura
a0b25e17ae ramips: glinet_gl-mt300n-v2: allow to use I2C and UART1 pins as GPIO
This is explicitly intended by the official documentation at
https://docs.gl-inet.com/en/3/specification/gl-mt300n-v2/#pcb-pinout

Signed-off-by: Martin Dziura <m.dziura@tum.de>
2022-11-13 21:51:22 +01:00
Arne Zachlod
364550f9d9 ramips: fix MAC address assignment for rt1800, e7350
previous commit ffa4b5283b introduced a bug which broke the MAC address
assignment for belkin,rt1800 and linksys,e7350.

Fixes: ffa4b5283b ("ramips: add support for Mikrotik LtAP-2HnD")
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2022-11-13 15:17:49 +01:00
Óscar García Amor
62efb34071 ramips: add support for Cudy WR1300 v2
Specifications:
 - SoC: MediaTek MT7621AT
 - RAM: 128 MB (DDR3)
 - Flash: 16 MB (SPI NOR)
 - WiFi: MediaTek MT7603E, MediaTek MT7613BE
 - Switch: 1 WAN, 4 LAN (Gigabit)
 - Ports: 1 USB 3.0
 - Buttons: Reset, WPS
 - LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS
 - Power: DC 12V 1A tip positive

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:
 - Loads only signed manufacture firmware due to bootloader RSA verification
 - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
 - connect to any lan ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button for image to
   download
 - See http://www.cudytech.com/newsinfo/547425.html

Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
2022-11-12 18:15:55 +01:00
Szabolcs Hubai
18801f2648 ramips: mt7621: use seama-lzma-loader for D-Link DIR-860L B1
Fix the LZMA ERROR 1 with a single line of recipe instead of duplicating
"uimage-lzma-loader".

While reviewing my original submission of commit ce19571004 David
suggested to use $(Device/uimage-lzma-loader), but due to the specific
needs of the vendor bootloader that simple oneliner didn't work.

The new $(Device/seama-lzma-loader) is for those SEAMA capable
bootloaders.

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2022-11-12 18:15:55 +01:00
Szabolcs Hubai
c293b492df ramips: rt3883: use seama-lzma-loader for D-Link DIR-645
In the support topic [0] of the GitHub issue #10634 it was found out
(based on boot logs) that the uimage-lzma-loader (commit 09faa73c53)
never worked, as an earlier workaround (commit 6fba88de19) negated
the recipe:

    3: System Boot system code via Flash.
    ## Booting image at bc050000 ...
    raspi_read: from:50000 len:40
    .raspi_read: from:50000 len:c
    .raspi_read: from:50000 len:1fa000
    ................................We have SEAMA, Image Size = 2072512
    Verifying Checksum ...
    Uncompressing SEAMA linux.lzma ... OK
    ## Transferring control to Linux (at address 80000000) ...
    ## Giving linux memsize in MB, 64

    Starting kernel ...

    [    0.000000] Linux version 5.4.188 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022
    [    0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
    [    0.000000] printk: bootconsolde [early0] enabled
    [    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
    [    0.000000] MIPS: machine is D-Link DIR-645
    [    0.000000] Initrd not found or empty - disabling initrd

Using the new seama-lzma-loader it's able to boot OpenWrt 22.03
and OpenWrt SNAPSHOT too:

    3: System Boot system code via Flash.
    ## Booting image at bc050000 ...
    raspi_read: from:50000 len:40
    .raspi_read: from:50000 len:c
    .raspi_read: from:50000 len:48b004
    .........................................................................We have SEAMA, Image Size = 4763588
    Verifying Checksum ...
    Uncompressing SEAMA linux.lzma ... OK
    ## Transferring control to Linux (at address 80000000) ...
    ## Giving linux memsize in MB, 64

    Starting kernel ...

    OpenWrt kernel loader for MIPS based SoC
    Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
    Decompressing kernel... done!
    Starting kernel at 80000000...

    [    0.000000] Linux version 5.10.144 (xabolcs@ut2004) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20774+2-b71affaf8b) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 Tue Sep 27 23:02:30 2022
    [    0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
    [    0.000000] printk: bootconsole [early0] enabled
    [    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
    [    0.000000] MIPS: machine is D-Link DIR-645
    [    0.000000] Initrd not found or empty - disabling initrd
    [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
    [    0.000000] Zone ranges:
    [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
    [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
    [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
    [    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2

The OKLI Loader is unable to read the flash on this SoC:

    Looking for OpenWrt image... not found! ('0xddbaddba' at 0xbc051000)

0: https://forum.openwrt.org/t/136435

Fixes: GitHub issue #10634 ("V22.03.0 release currently does not work on D-Link DIR-645")
Fixes: 09faa73c53 ("ramips: rt3883: use lzma-loader for DIR-645")
Tested-by: Glenn Fowler <gfowler1@outlook.com>
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2022-11-12 18:15:55 +01:00
Szabolcs Hubai
e7ad68d682 ramips: define lzma-loader recipe for SEAMA devices
Define "Device/seama-lzma-loader" recipe for SEAMA devices to help
contributors avoid doing recipe mistakes.

In a forum topic [0] I was under the impression that the good old
uimage-lzma-loader didn't fix the LZMA ERROR 1 for a device.

It was found out, that the uimage-lzma-loader never worked because the
KERNEL variable was overriden earlier (also an LZMA ERROR 1 related
commit, 6fba88de19), and the "use lzma-loader" fix (commit
09faa73c53) didn't catch that to include the "loader-kernel" part.

I contributed an LZMA ERROR 1 fix (commit ce19571004) for the SEAMA
device D-Link DIR-860L B1, where I had to duplicate the whole
uimage-lzma-loader recipe because of the special needs of the vendor
bootloader.

This new recipe reuse most of uimage-lzma-loader's KERNEL definiton to
avoid duplication.

It uses "relocate-kernel" as it needed for D-Link DIR-860L B1 to
boot from flash, and it's compatible with D-Link DIR-645 too.

It repacks lzma-loader with lzma for kernel (without uImage), because
these weird hacked vendor bootloaders accepts only LZMA compressed
kernels from flash:

    We have SEAMA, Image Size = 4759794
    Verifying Checksum ...
    Uncompressing SEAMA linux.lzma ... OK

It uses uImage header for initramfs kernel to be little bit verbose.

0: https://forum.openwrt.org/t/136435/10

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2022-11-12 18:15:55 +01:00
Arne Zachlod
ffa4b5283b ramips: add support for Mikrotik LtAP-2HnD
Mikrotik LtAP-2HnD is a outdoor/automotive WLAN 4 router with integrated GPS
receiver and two mPCIe slots.

Specifications:
* SoC: MT7621A
* RAM: 128 MiB Nanya NT5CC64M16GP-DI
* Flash: 16 MiB winbond W25Q128JV
* WLAN:
  * Atheros AR9382 with power amplifier SKY 85330 (2x2 internal antennas,
    with RF switches for external connectors)
* Ethernet: 1 Gbps, single port
* USB Host: USB 2.0 Speeds
* Serial: 115200 baud
* LEDs: Power, System, GPS, 5* RSSI
*  mPCIe:
   * miniPCIe slot 1: PCIe and USB 2.0 Host (via switch shared with USB Host)
   * miniPCIe slot 2: USB 2.0 and 3.0
* SIM Cards:
  * Slot 1 Connected to mPCIe slot 1
  * Slot 2 and 3 connected to mPCIe slot 2 via switch
* GPS: MTK 3333 on serial port 2 (/dev/ttyS1), 115200 baud and PPS on gpio 14

gpios are exposed to /sys/class/gpio:

* usb-select: swithes USB 2.0 interface between external port and internal
mPCIe slot 1 default is the external USB interface
* gps-reset: resets the GPS interface chip
* sim-select: switches between sim slot 2 and 3 connected to mPCIe slot 2
* gps-ant-select: switches GPS antenna between internal antenna and SMA
connected antenna
* lte-reset: resets mPCIe slot 2

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2022-11-12 18:15:55 +01:00
Felix Fietkau
04b8ad60fd kernel: more fixes for mtk_eth_soc performance optimization
- fix features sync between netdevs
- fix crash in dsa_switch_rcv

Fixes: ceb1451c10 ("kernel: add mediatek soc ethernet performance improvements")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-10 22:27:18 +01:00
Felix Fietkau
ceb1451c10 kernel: add mediatek soc ethernet performance improvements
- implement multiqueue via qdma hardware shaper to deal with ports with different speeds
- implement hardware DSA untagging
- add NETIF_F_ALL_TSO to reduce unnecessary segmentation

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 18:18:27 +01:00
David Bauer
10ba380ec3 ramips: define loadaddr for U6 Lite DTB
The Ubiquiti UniFi 6 Lite does not correctly align the FDT by always
setting fdt_high to 0xffffffff when invoking the bootubnt command.

Work around this issue by loading the DTB to a valid,aligned address, so
the bootloader does not have to relocate the FDT automatically.

Note: The device does read the kernel before invoking bootm on the FIT
image to 0x86000000.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-11-08 12:16:43 +01:00
Michael Lyle
961e01fc67 ramips: gl-mt1300: downclock SPI to 50MHz
The SPI max frequency was set to 80MHz, considerably higher than the
vendor clocks it in their firmware (10MHz).  Multiple users reported
jffs2 corruption/instability in GitHub issue #10461.

My unit has a W25Q256; datasheet specifies maximum SPI frequency for
read command of 50MHz.

Thanks to @DragonBlueP for suggesting to eliminate m25p,fast-read;
and @MPannen1979 for identifying the problem.

Fixes: #10461
Signed-off-by: Michael Lyle <mlyle@lyle.org>
2022-11-07 12:54:31 +01:00
Sungbo Eo
02aa7a2bb9 ramips: fix TP-Link RE200 v3/v4 LEDs
Set power LED to gpio 43 instead of 44 for v3 and v4.
Set red wifi LED to gpio 40 (was assigned to `red:wifi5g`).

Tested by the author of the initial v3 and v4 commit.

Reported-by: Richard Fröhning <misanthropos@gmx.de>
Tested-by: Richard Fröhning <misanthropos@gmx.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-11-07 12:33:42 +01:00
Linos Giannopoulos
78110c3b5f ramips: add support for TP-Link MR600 V2(EU)
MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation
etc. and can reportedly achieve higher bandwidth with it.

- Specifications:

* SoC: Mediatek MT7621DAT 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* LTE Modem: Qualcomm MDM9240
* WiFi 5GHz: Mediatek MT7613BEN
* WiFi 2.4GHz: Mediatek MT7603EN
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console (115200 8n1), J1(GND:3)
* Buttons: Reset, WPS.
* LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2,
  Signal3

- MAC Addresses:

OEM firmware configuration:
54:af:97:xx:xx:7b : 2.4G
54:af:97:xx:xx:7a : 5G
54:af:97:xx:xx:7c : LTE
54:af:97:xx:xx:7b : LAN (label)
54:af:97:xx:xx:7c : WAN

- Installation:

1. Download the OpenWrt initramfs-image.

Place it into a TFTP server root directory and rename it to openwrt.img
Configure the TFTP server to listen at 192.168.0.5/24.

3. Connect to the serial console.

Attach power and interrupt the boot procedure when prompted (type `tpl`).

Credentials are admin / 1234

4. Configure U-Boot for booting OpenWrt from ram

 $ tftpboot
 $ bootm

5. Transfer the OpenWrt sysupgrade image to the device.

- LTE:

In order to setup the wwan0 interface:
1. Add a `qmi` proto interface under `/etc/config/network`, e.g.:
```
config interface 'wwan0'
        option device '/dev/cdc-wdm0'
        option proto 'qmi'
        option pincode 'XXXX'
        option apn 'your_isp_apn'
```

2. Add `wwan0` interface to the `wan` firewall zone
3. `/etc/init.d/network restart`

Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
2022-11-05 23:13:16 +01:00
Shiji Yang
f7f9203854 ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based
on Tenbay WR1800K. They have the same hardware circuits and u-boot.
SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile),
SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these
models run the same firmware.

Specifications:
 SOC:      MT7621 + MT7905 + MT7975
 ROM:      128 MiB
 RAM:      256 MiB
 LED:      status *3 R/G/B
 Button:   reset *1 + wps/mesh *1
 Ethernet:      lan *3 + wan *1 (10/100/1000Mbps)
 TTL Baudrate:  115200
 TFTP Server:   192.168.1.254
 TFTP IP:       192.168.1.28 or 192.168.1.160 (when envs is broken)

MAC Address:
 use        address               source
 label      30:xx:xx:xx:xx:62     wan
 lan        30:xx:xx:xx:xx:65     factory.0x8004
 wan        30:xx:xx:xx:xx:62     factory.0x8004 -3
 wlan2g     30:xx:xx:xx:xx:64     factory.0x0004
 wlan5g     32:xx:xx:xx:xx:64     factory.0x0004 set 7th bit

TFTP Installation (initramfs image only & recommend):
1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
   directory of the tftp server. (tftpd64 is a good choice for Windows)
3. Start the TFTP server, plug in the power supply, and wait for the
   system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin", we need
   it to back to stock firmware.
5. Use "fw_printenv" command to list envs.
   If "firmware_select=2" is observed then set u-boot enviroment:
   /# fw_setenv firmware_select 1
6. Apply sysupgrade.bin in OpenWrt LuCI.

Web UI Installation:
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs.
   If "firmware_select=2" is observed then set u-boot enviroment:
   /# fw_setenv firmware_select 1
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.

Recovery to stock firmware:
a. Upload "firmware.bin" to OpenWrt /tmp, then execute:
   /# mtd -r write /tmp/firmware.bin firmware
b. We can also write factory image "UploadBrush-bin.img" to firmware
   partition to recovery. Upload image file to /tmp, then execute:
   /# mtd erase firmware
   /# mtd -r write /tmp/UploadBrush-bin.img firmware

How to extract stock firmware image:
  Download stock firmware, then use openssl:
  openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \
  -out "firmware.tar.tgz" -k QiLunSmartWL

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 22:38:01 +01:00
Alexander Horner
53f2e438cb ramips: add support for Zbtlink ZBT-WG1602-V04
Description heavily based on commit
7e89421a7c by
Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have
been removed

Completed with great help from \x on IRC. Thanks, \x!

Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe
slots with USB and SIM only and another one which is a pure miniPCIe
slot as well as five Gigabit Ethernet ports (4xLAN + WAN).

Specification:

* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2)
* WLAN 5GHz: MT7662E (.11nac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 3.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled,
  1 power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)

Additional HW information:

* SoC USB port 1 is shared by internal miniPCIe slot and external
  Type-A USB port, USB D+/D- lines are toggled between ports using a
  GPIO controlled DPDT switch.

Installation:

The kernel image can be installed directly onto the device via a browser
to 192.168.1.1 using the built in firmware recovery Web UI available.
It can be accessed by pushing the reset button in, applying power and
holding the reset button for approximately 10 seconds. When the kernel
image has been flashed, you can access LuCI and upload the sysupgrade
as normal.

Signed-off-by: Alexander Horner <ahorner@programmer.net>
2022-11-05 21:12:25 +01:00
Shiji Yang
7a504c151d ramips: add support for Youku X2
Specifications:
  SOC:      MT7620AN + MT7612EN
  RAM:      128 MiB DDR2
  Flash:    16 MiB (Winbond W25Q28FVFG)
  WLAN:     2.4G + 5G
  LAN:      LAN ports *2
  WAN:      WAN port *1
  USB:      USB2.0 *1
  SD Card:  MicroSD *1
  Buttons:  Reset *1
  LEDs: ethernet *3, system, usb, wlan2g, wlan5g

MAC Address:
  use        address               source
  label      54:36:9b:xx:xx:ac     lan
  lan        54:36:9b:xx:xx:ac     factory.0x0028
  wan        54:36:9b:xx:xx:ad     factory.0x002e
  wlan2g     54:36:9b:xx:xx:ae     factory.0x0004
  wlan5g     54:36:9b:xx:xx:af     factory.0x8004

Installation:
1. Apply initramfs-kernel.bin in stock firmware Web UI.
2. Install sysupgrade.bin on OpenWrt and do not retain any configuration.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 21:12:24 +01:00
Shiji Yang
eba0a8deb6 ramips: improve compatibility for Youku YK-L2 and YK-L1 series
Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install
initramfs-kernel.bin from the stock firmware Web UI. At the same time,
this change makes it possible to boot OpenWrt with the official u-boot.

Notice:
Since the stock firmware is based on OpenWrt and the configuration
will be retained by default during the upgrade process, so we must use
initramfs-kernel.bin to do a initial installation. After the system
restarts, install sysupgrade.bin and do not retain any configuration.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 21:12:24 +01:00
John Audia
1eebe72a80 kernel: bump 5.15 to 5.15.77
Manually rebased:
   bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
   bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
   bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
   bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
   lantiq/patches-5.15/0028-NET-lantiq-various-etop-fixes.patch

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-05 16:26:38 +01:00
John Audia
87edb650c7 kernel: bump 5.10 to 5.10.153
Manually rebased:
  bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
  lantiq/patches-5.10/0028-NET-lantiq-various-etop-fixes.patch

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-05 16:26:00 +01:00
Volodymyr Puiul
08e153c3c3 ramips: add support for YunCore FAP690
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI NOR
- Wi-Fi:
    - MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 1x 1GiE via MT7530
- UART: J4 (115200 baud)
    - Pinout: [3V3] (TXD) (RXD) (GND)

- Bootloader: U-Boot
- Buttons:
    - SW1 - no label on the box, combined with led
- Led: Status. RGB controlled by
    - GPIO 14 - green color
    - GPIO 15 - red color
    - GPIO 16 - blue color

Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
it will not boot.

MAC addresses as verified by OEM firmware:
vendor   source
LAN      factory 0x4 (label)
5g       factory 0x4 (label)
2g       label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
	4-th byte

Example
label:  44:xx:xx:b7:xx:xx
lan:    44:xx:xx:b7:xx:xx
2g      46:xx:xx:c7:xx:xx
5g      44:xx:xx:b7:xx:xx

Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2022-10-31 22:01:49 +01:00
Volodymyr Puiul
3d14c610e8 ramips: add support for YunCore FAP640
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI
- Wi-Fi:
    - MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN
- UART: J4 (115200 baud)
    - Pinout: [3V3] (TXD) (RXD) (GND)
- Power: 802.11af/at PoE;

- Bootloader: U-Boot
- Buttons:
    - Reset
- LEDs:
    - Status - RGB controlled by
      - GPIO 14 LOW - green color
      - GPIO 15 LOW- red color
      - GPIO 16 LOW - blue color
    - WAN - gren color, controlled by switch GPIO 12 LOW
    - LAN1 - gren color, controlled by switch GPIO 9 HIGH
    - LAN2 - gren color, controlled by switch GPIO 6 LOW
    - LAN3 - gren color, controlled by switch GPIO 3 LOW
    - LAN4 - gren color, controlled by switch GPIO 0 LOW

Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
router will not boot.

MAC addresses with OEM firmware:
vendor   source
lan      factory 0x4 (label)
5g       factory 0x4 (label)
2g       label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
  4-th byte

Example
label:  44:xx:xx:b7:xx:xx
lan:    44:xx:xx:b7:xx:xx
2g      46:xx:xx:c7:xx:xx
5g      44:xx:xx:b7:xx:xx

Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2022-10-30 23:14:45 +01:00
Shiji Yang
288b36c2ea ramips: add missing WAN LED for Xiaomi Mi Router 4A / 4C
The blue WAN LED connected to GPIO37 is missing, so re-add it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-10-23 23:33:22 +02:00
David Bentham
67660d3667 ramips: fix WAN mac address allocation for Unielec 01 and 06 models
Manufacturer has predetermined mac address values for lan and wan ports.

This change keeps inline with other mt7621 devices mac address allocation
from factory mtd partition.

Example from hexdump output:

0xe000 0x6 (lan) -           0xe006 0x6 (wan)

0000e000  70 b3 d5 10 02 96 70 b3  d5 10 02 95 ff ff ff ff

Previous change had created an overlapping mac address situation as it
would increment by one based on the lan mac address location found in the
factory partition, which would sometimes increment to the same as the
mt7603 wifi chip.

Tested on Unielec u7621-01 model

Signed-off-by: David Bentham <db260179@gmail.com>
2022-10-23 01:45:52 +02:00
Robert Senderek
ac296f6210 ramips: rt3883: enable lzma-loader for Belkin F9K1109v1
Fixes boot loader LZMA decompression issues

Fixes: #10968
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
2022-10-23 01:45:52 +02:00
Alex Khodin
f6099d7974 ramips: mt7621: enable lzma-loader for Asus RT-N56U-B1
Fixes boot loader LZMA decompression issues.

Without this change the board end up in a boot loop.

Signed-off-by: Alex Khodin <mxktz1@gmail.com>
2022-10-23 01:45:52 +02:00
Chukun Pan
4f9b360f0b ramips: add A-040W-Q alternative name for MSG1500 X.00
The hardware of Nokia A-040W-Q and RAISECOM MSG1500 X.00 are
exactly the same, both of which are customized by operators.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-23 01:45:52 +02:00
Aleksander Jan Bajkowski
9226f1e419
kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic config
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.

Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....

Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
  If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
  option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
  the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC -  enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-21 13:47:01 +02:00
Andrey Butirsky
47d58afbdf ramips: kndrt31r19: set up wan interface by default
The only WAN port of the device is it's modem, so set it up as such

Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-10-19 23:00:40 +02:00
INAGAKI Hiroshi
00ddd29b65 build: move Build/edimax-header to image-commands.mk
To use from the following devices in ath79 target, move edimax-header to
image-commands.mk.

- ELECOM WRC-300GHBK2-I
- ELECOM WRC-1750GHBK2-I/C

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-19 22:58:12 +02:00
Rafał Miłecki
711f1a8bcb kernel: mtd: backport SafeLoader parser
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-19 07:07:14 +02:00
Petr Štetiar
b63d6d4730 mt7621: hiwifi_hc5962: fix reboot loop by using LZMA loader
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

References: https://github.com/openwrt/openwrt/issues/10645#issuecomment-1282607274
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-18 19:05:06 +02:00
Petr Štetiar
7dd1cab1c1 mt7621: netgear_ex6150: fix reboot loop by using LZMA loader
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

Fixes: #10645
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-18 09:01:39 +02:00
Du Cai
8ac69159f2 ramips: use lzma-loader on JCG Q20
Fixes the LZMA uncompression issue on JCG Q20.

Signed-off-by: Du Cai <caidu@smail.nju.edu.cn>
2022-10-09 22:50:57 +02:00
John Audia
9110126620 kernel: bump 5.15 to 5.15.72
Removed upstreamed:
  generic/pending-5.15/722-net-mt7531-only-do-PLL-once-after-the-reset.patch[1]
  bcm53xx/patches-5.15/082-v6.0-clk-iproc-Do-not-rely-on-node-name-for-correct-PLL-s.patch[2]

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72
Run-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72 (RB5009UG+S+IN)

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=5de02ab84aeca765da0e4d8e999af35325ac67c2
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=ab5c5787ab5ecdc4a7ea20b4ef542579e1beb49d

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-09 22:26:16 +02:00
Matthias Schiffer
149fc3a269
ramips: fix switch setup for ASUS RT-AX53U
The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface
corresponding to the non-existing port.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2022-10-03 13:23:41 +02:00
Alexey Kosmakov
a664d39c5b ramips: add support for SNR SNR-CPE-ME2-Lite
SNR SNR-CPE-ME2-Lite is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A.

Specification:
    - SoC           : MediaTek MT7621A
    - RAM           : DDR3 128 MiB
    - Flash         : SPI-NOR 16 MiB
    - WLAN          : 2.4 GHz 2T2R (MediaTek MT7603E)
                      5 GHz 2T2R (MediaTek MT7613BE)
    - Ethernet      : 10/100/1000 Mbps x5
      - Switch      : MediaTek MT7530 (SoC)
    - UART          : through-hole on PCB
      - J4: 3.3V, GND, TX, RX
      - 57600n8
    - Power         : 12 VDC, 1.5 A

Flash instruction via WEB (firmware 1.10.4 and later)
    1. Boot SNR-CPE-ME2-Lite normally with "Router" mode
    2. Access to "http://192.168.1.1/" and open "Administration -> Management" page
    3. Select the OpenWrt factory image in "Firmware update" section and click "Update" button
    4. Wait ~120 seconds to complete flashing

Flash instruction via TFTP (all version):
    1. Boot SNR-CPE-ME2-Lite to recovery mode (hold the reset button while power on)
    2. Send firmware via TFTP client:
       TFTP Server address: 192.168.1.1
       TFTP Client address: 192.168.1.131
    3. Wait ~120 seconds to complete flashing

Signed-off-by: Alexey Kosmakov <a.kosmakov@nagtech.ru>
2022-10-02 20:21:55 +02:00
Mark King
bf5b1a53d4 ramips: enable LZMA loader to fix Linksys RE6500 boot
At some point after 21.02.3 and before 22.03.0, the size limits of the
Linksys RE6500 were reached and prevent booting from the 22.03.0 release
or builds of current SNAPSHOT. This patch allows builds of master to boot
again and has been tested on my device.

Fixes: #8577

Signed-off-by: Mark King <mark@vemek.co>
2022-10-02 20:21:55 +02:00
Daniel Golle
ca0e7054d8 ramips: add led driver to UniFi FlexHD defaut package set
Add kmod-leds-ubnt-ledbar to the packages selected by default on the
UniFi FlexHD access point.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-30 13:29:58 +01:00