Commit Graph

538 Commits

Author SHA1 Message Date
David Bauer
5568c8a9fe ath79: add ar71xx support-list entry for Fritz4020
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-26 23:20:04 +01:00
Chuanhong Guo
3bd871ad52 ath79: fix wmac memory region for qca953x
According to /arch/mips/include/asm/mach-ath79/ar71xx_regs.h
the size of wmac register range for qca953x is only 0x20000.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-02-20 18:51:31 +01:00
INAGAKI Hiroshi
93d4439454 ath79: add support for I-O DATA WN-AC1600DGR
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- SoC:      Qualcomm Atheros QCA9557
- RAM:      128 MB
- Flash:    16 MB
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
  - Switch: QCA8337N
- LED/key:  6x/6x(4x buttons, 1x slide switch)
- UART:     through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Alternative flash instruction using initramfs image:

1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing

This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:15 +01:00
Santiago Piccinini
cc8bd77772 ath79: fix qca955x dual pci resource allocation
Tested with a dual pci QCA9558 board (LibreRouter v1) in three
configurations: enabling pcie0 only, pcie1 only and both enabled.

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
2019-02-14 16:56:15 +01:00
Santiago Piccinini
eea66c3227 ath79: fix qca955x pcie0 memory size
Datasheet states that both PCI ranges are of 0x2000000 size:
0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000.

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
2019-02-14 16:56:15 +01:00
Paul Wassi
dee8db441e ath79: proper indentation in image/common-tp-link.mk
Add two spaces for proper indentation in image/common-tp-link.mk

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
212892ce70 ath79: fix port order on TL-WR841ND-v7
The switch ports are seen one to one on the case.
Also remove unneeded secondary port numbers in this
case statement.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
97fcd2622a ath79: change ledtrig on GL.iNet AR150
Change the ledtrig for LAN from netdev to switch.
Although eth1 comes out of the device at a single port,
this port is a switch-port and therefore the LED
must be triggered by that.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
79cc48ff60 ath79: rename TP-LINK to TP-Link
Remove inconsistencies in the vendor's name.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
ff541c5ca2 ath79: rename TL-WR740ND-v4 to TL-WR740N-v4
Give the device the same name it had in ar71xx.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
da1107f8a5 ath79: fix TL-WR741ND-v4 switch port order
Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:13 +01:00
David Bauer
0c24b363a6 ath79: add support for Xiaomi Mi Router 4Q
Hardware
--------
CPU:   Qualcomm Atheros QCA9561
RAM:   64M DDR2
FLASH: 16M SPI-NOR
ETH:   1x WAN - 2x LAN
WiFi:  QCA9561 3T3R
BTN:   1x Reset - 1x WPS
LED:   1x Blue - 1x Red - 1x Yellow
UART:  TX - GND - RX - VCC (From ethernet port)
       115200n8 - 3.3V

Installation
------------
1. Connect to the device via UART.

2. Interrupt the U-Boot on power-on by pressing enter when prompted.

3. Connect you computer to one of the routers LAN ports.
   Assign yourself the IP 192.168.31.10/24.
   Copy the OpenWRT initramfs image to a tftp server root directory.
   Rename the image to 'x4q.bin'.

4. Load the initramfs image to the router by executing following command
   in U-Boot. The image will boot afterwards.

   > tftpboot 0x81000000 x4q.bin; bootm

5. SCP the sysupgrade-image into '/tmp'.
   Remember to assign yourself an IP in 192.168.1.0/24 for this step!

6. Install OpenWRT permanently by executing

   > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-11 19:04:06 +01:00
Petr Štetiar
5fd68d60e4 ath79: ag71xx: Fix tx queue timeouts during ifup
On ath79 and UBNT Bullet M XW (ar9342) I was experiencing weird issues during
network setup[1] which I was able to reproduce easily with following commands:

 uci set network.lan.ipaddr='192.168.1.20'
 uci commit network
 ifup lan

Which resulted after some time in:

 ...
 WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x16c/0x280
 NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out
 ...

Sometimes I wasn't able to use networking anymore, sometimes it was enough to
just ifdown/ifup lan and network was backup. On ar71xx it was all working just
fine.

I've found out, that it was happening because ag71xx_poll() wasn't called, thus
the TX queue wasn't emptied. The ag71xx_poll() is being called from napi
hrtimer, which is enabled by napi_schedule() in ar71xx_interrupt(), but since
no interrupts were ever fired again after ag71xx_stop() was called, it was
always leading to tx queue timeouts:

 *** ag71xx_hard_start_xmit()
 eth0: packet injected into TX queue
 eth0: raw intr=00000001 TXPS POLL
 eth0: enable polling mode
 eth0: processing TX ring, flush=no
 eth0: disable polling mode, rx=1, tx=1,limit=32

 ( `ifup lan done here` )

 *** ag71xx_stop()
 *** ag71xx_open()
 *** ag71xx_hw_enable()
 IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
 IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 *** ag71xx_hard_start_xmit()
 eth0: packet injected into TX queue
 *** ag71xx_hard_start_xmit()
 eth0: packet injected into TX queue
 ...
 WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274

So I've looked at ag71xx_stop() in ar71xx, added the missing bits to ath79 and
fixed this issue.

1. https://github.com/openwrt/openwrt/pull/1635#issuecomment-448638246

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[move ag->link before ag71xx_hw_disable to retain ordering as original]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-07 14:19:46 +01:00
Oldřich Jedlička
12310f05b7 ath79: add support for TP-LINK Archer C7 v4
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
2019-02-05 19:37:31 +01:00
Skirmantas Lauzikas
9c01273e5e ath79: add support for TP-Link Archer C2 V3 (AC900)
This commit adds support for the TP-link Archer C2 V3 (AC900).

Specifications:

 - CPU: QCA9563 750Mhz
 - Ram: 64MB (DDR2)
 - Flash: 8MB (SPI NOR)
 - Ethernet: 5x 10/100/1000
 - Wifi: QCA9563 bgn + QCA9887 an+ac
 - 9x Leds, 2x buttons

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin
via the router Web interface and flash as normal firmware update.

Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reorder entries, fix trailing whitespace in dts, add firmware partition
 compatible string, remove led default off states, use default on state
 for system led, reuse tplink-safeloader-uimage image build recipe, squash
 with dynamic partitioning commit, reword commit message, add
 installation instructions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-27 16:41:10 +01:00
Django Armstrong
1c2f7b5115 ath79: add support for Devolo WiFi Pro 1750e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN:   1x Reset
       1x WPS
       1x USB eject
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
       Dupont 4 pin header
       Rear RJ45 serial port non-functional
USB:   1x v2.0

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
2019-01-26 21:46:33 +01:00
Petr Štetiar
89afabf9f8 ath79: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[split up, removed entries where it could clash due to ath9k-leds]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-26 21:09:12 +01:00
Petr Štetiar
a012b3dfa8 ath79: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-26 21:09:12 +01:00
Jeff Kletsky
ee3120a9db ath79: fix GL.iNet AR300M family GPIOs/LEDs
Change the "status" LED to proper GPIO 12 and "red" naming.

Remove GPIO 2 from definition as a USB LED.

GPIO 2 is used to control power to the USB socket, not an LED.
As such, PWM on the line or typical LED triggers are inappropriate.

Users who wish to control the USB power for custom applications
can manipulate the GPIO through code, or for example, export it
through /sys/class/gpio/export.

Runtime-tested:  GL.iNet AR300M-Lite

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-01-26 10:40:06 +01:00
Koen Vandeputte
528508ae8b kernel: bump 4.14 to 4.14.95
Refreshed all patches.

Removed superseded patches:
- 0400-Revert-MIPS-smp-mt-Use-CPU-interrupt-controller-IPI-.patch

Compile-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370), x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Mathias Kresin <dev@kresin.me>
Tested-by: Robert Resch <openwrt@webnmail.de>
2019-01-24 10:10:45 +01:00
Sebastian Kemper
69dfdda157 ath79: fix port order for dir 825-c1 and 835-a1
LAN ports 1 and 4 and 2 and 3 are interchanged. Fix this in 02_network
so the ports show up in the correct order in luci.

The correct ucidef_add_switch line is already present. This commit moves
the blocks around to keep alphabetical order.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
2019-01-22 09:05:59 +01:00
Milan Krstic
76a629ee35 ath79: ag71xx: preserve port mirror flags during swconfig apply
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2019-01-22 09:05:59 +01:00
David Bauer
c8115167f9 ath79: add support for devolo WiFi pro 1200i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-05 21:55:22 +01:00
David Bauer
8d68be8057 ath79: add support for devolo WiFi pro 1750i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-05 21:55:22 +01:00
Paul Wassi
eb1887be93 ath79: merge cases in 02_network
Merge some duplicate cases in /etc/board.d/02_network

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-01-02 22:36:27 +01:00
Christoph Krapp
59b99e1924 ath79: align GL-AR750S boardname to other GL.iNet devices
As the official device name is GL-AR750S, rename the board accordingly.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-01-01 19:42:41 +01:00
Paul Wassi
54e3ee0215 ath79: fix case statement in 01_leds
Fix a missing 'end-of-case' recently introduced in 01_leds

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-01-01 01:38:51 +01:00
Mathias Kresin
8c485fbb25 ath79: rework elecom-header recipe
Replace the code with a more readable version. Rename the recipe
to reflect the real usecase.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 16:48:49 +01:00
Paul Wassi
28a5674e33 treewide: fix spaces vs. tabs
Fix spaces vs. tabs issues in ath79 and ramips.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 16:37:20 +01:00
Rosy Song
1c39dcc2bb ath79: tweak the position of factory partition for wr818
The 'factory' partition will move to 0x50000-0x60000 in 2019. As
the webserver in bootloader is compatible with different mtdlayout,
all the users still can upgrade firmware whatever on ath79 or ar71xx.

Signed-off-by: Rosy Song <rosysong@rosinson.com>
2018-12-31 16:37:09 +01:00
Roger Pueyo Centelles
3dfc07d186 ath79: add support for COMFAST CF-E110N
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.

Specifications:

 - 650/400/216 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, both with PoE-in support
 - 64 MB of RAM (DDR2)
 - 16 MB of FLASH
 - 2T2R 2.4 GHz, up to 26 dBm
 - 11 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new want, so a factory reset will be
 needed: once the new firmware is flashed, perform the factory reset by
 pushing the reset button several times during the boot process, while the
 WAN LED flashes, until it starts flashing quicker.

 The U-boot bootloader contains a recovery HTTP server to upload the
 firmware. Push the reset button while powering the device on and keep it
 pressed for >10 seconds. The recovery page will be at http://192.168.1.1

Notes:

 The device is advertised, sold and labeled as "CF-E110N", but the
 bootloader and the stock firmware identify it as "v2".

Acknowledgments:

 Petr Štetiar <ynezz@true.cz>
 Sebastian Kemper <sebastian_ml@gmx.net>
 Chuanhong Guo <gch981213@gmail.com>

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 16:25:11 +01:00
Georgi Vlaev
d03aae1a09 ath79: add support for TP-Link Archer C6 v2
This patch adds support for TP-Link Archer C6 v2 (EU)

Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board

Flash instructions:

Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
   tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
   button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing

According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
2018-12-31 16:25:11 +01:00
Guan-Hong Lin
9ebb44aef4 ath79: add support for EnGenius EWS511AP
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.

Short specification:

- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
   (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
   (ath)> erase 0x9f060000 +f50000
   (ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
   (ath)> reset

Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
2018-12-31 16:25:09 +01:00
Paul Wassi
48745221a8 ath79: add status LED on GL.iNet AR300M
This adds the triggers for the status LED of this device.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:24:55 +01:00
Paul Wassi
6e78d546d1 ath79: fix boardname of GL.iNet GL-AR300M
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 14:24:21 +01:00
Paul Wassi
cdbf2de777 ath79: Add support for TP-Link WR810N
Device specifications given in b23b0fb28b

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:18:19 +01:00
Paul Wassi
c2ecec07cc ath79: Add GL.iNet AR150 LED triggers
When switching from ar71xx to ath79 the default netdev LED
triggers for LAN and WAN got lost.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:05:26 +01:00
Paul Wassi
8ba76d6e74 ath79: fix boardname of GL.iNet GL-AR150
This device is called GL-AR150, therefore rename the board
to 'gl-ar150'

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:05:26 +01:00
INAGAKI Hiroshi
caf306ce91 ath79: add support for ELECOM WRC-1750GHBK2-I/C
ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac
routers, based on Qualcomm Atheros QCA9563.

This commit also includes small fix; use "0x0x03000101" as pll_1000
instead of "0x03000000".

Specification:

- SoC:      Qualcom Atheros QCA9563
- RAM:      128 MB (DDR2)
- Flash:    16 MB (SPI-NOR)
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 10/100/1000 Mbps
- LED/key:  4x/3x (2x buttons, 1x slide-switch)
- UART:     through-hole on PCB
  - Vcc, RX, GND, TX from switch (QCA8337N) side
  - 115200n8

Flash instruction using factory image:

1. Boot WRC-1750GHBK2-I/C normaly
2. Access to "http://192.168.2.1/" and open firmware upgrade page
("ファームウェア更新 手動更新(アップデート)")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, perform sysupgrade with
squashfs-sysupgrade image
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-31 21:38:53 +09:00
Paul Wassi
ab12913676 ath79: Fix UBNT Unifi AC LEDs
Both LEDs on these devices are ACTIVE_HIGH, change back to what
it is on ar71xx.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 13:28:31 +01:00
Paul Wassi
31dc0fbca3 ath79: Fix system LED on TP-Link WR740/741 v4
The system LED on these devices is ACTIVE_LOW, change back to what
it is on ar71xx.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 13:28:31 +01:00
Antonio Silverio
9601d94138 ath79: add support for TP-Link TL-WR841N/ND v8
CPU: Atheros AR9341 535MHz
RAM: 32MB
FLASH: 4MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9341 2x2:2 bgn
LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill
BTN: WPS, WiFi, Reset

Installation:
Upload the factory image via the vendor-GUI.

Signed-off-by: Antonio Silverio <menion@gmail.com>
[resolve merge conflicts, squash commits, fix commit title, remove
default default off led properties, mark sysupgrade image compatible
with the ar71xx version of the board, drop blank lines from dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 13:28:31 +01:00
David Bauer
98f826fdc0 ath79: use caldata patching for Archer C58/C59
With this commit the TP-Link Archer C58 and Archer C59 use caldata
patching in order to set the correct 5GHz MAC-address.

Tested on TP-Link Archer C59 v1.

For more details see commit 330965b.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-31 13:28:31 +01:00
Christoph Krapp
af28d8a539 ath79: add support for GL.iNet GL-AR750S
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.

Furtheremore support for the MicroSD port is not implemented as of now.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
  - Another LED can be accessed on GPIO 7 if soldered

Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 13:28:20 +01:00
David Bauer
06b1a6e885 ath79: fix OCEDO Koala ethernet configuration
The OCEDO Koala has incorrect PLL settings which result in ~3% packet
loss on ethernet connections.

Also omit the gmac-configuration as it's incorrect too.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-30 20:08:13 +01:00
Weijie Gao
abc7ed2c58 ath79: add support for D-Link DIR-859 A1
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880

USB is supported on the PCB but not connected.

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or the u-boot
   failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted. Otherwise the u-boot
   will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the firmware
   checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
   upgrade the factory.bin through the u-boot failsafe interface and then goto
   step 2.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
Eduardo Barros
335c69fbb2 ath79: Fix wrong TL-WR740N v4 switch port order
Fix the switch port order to have the correct order in LuCI.

Fixes: FS#1469

Signed-off-by: Eduardo Barros <geadas@gmail.com>
[trim commit title, add a proper commit message, add fixes tag, keep
alphabetical order of the blocks]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-29 16:12:41 +01:00
David Bauer
97dc323a4c ath79: fix Archer A7 v5 5GHz MAC adress
Currently all Archer A7 v5 have the same (incorrect) MAC address.
The address is currently derived from eth1 which is not present on the
QCA9563. Use eth0 to get the correct MAC address.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-29 12:35:47 +01:00
Petr Štetiar
6ab138fa84 ath79: ubnt-bullet-m-xw: Remove eth1 disabled node
It's redundant as eth1 is disabled by default in ath79.dtsi.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-27 16:02:25 +01:00
Petr Štetiar
74f46d90be ath79: ubnt-bullet-m-xw: Move eth0 mtd-mac-address to the common include
It's same for Bullet and Nanostation so far, so let's hope it's going to
be the same for other boards sharing the same platform.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-27 16:02:25 +01:00
Petr Štetiar
6935d73851 ath79: ubnt-bullet-m-xw: Remove pll-data property from eth0 node
It's not necessary as it's already defined in ar934x.dtsi to:

  pll-data = <0x16000000 0x00000101 0x00001616>;

And in ar71xx it's currently set to the same values:

 #define AR934X_PLL_VAL_1000	0x16000000
 #define AR934X_PLL_VAL_100	0x00000101
 #define AR934X_PLL_VAL_10	0x00001616

And dumping the value from the airOS v6.1.7 has the same value:

  AR934X_PLL_ETH_XMII_CONTROL_REG 0x1805002C 0x101

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-27 16:02:24 +01:00
Petr Štetiar
965ce07dbb ath79: ubnt-xw: Add LED aliases for diag and status LED support
Currently there is no LED signalization for various system states
implemented in diag.sh, so this patch adds support for it.

Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-27 16:02:23 +01:00
David Bauer
e67da34431 ath79: add support for devolo WiFi pro 1750c
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).

It is also not mentioned in the devolo manual.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-27 14:06:38 +01:00
David Bauer
1724d4e9ed ath79: add support for devolo WiFi pro 1200e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-27 14:06:38 +01:00
TOCK Chiu
8471944325 ath79: add support for TP-Link Archer C7 v5
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.

Specification:
-   QCA9563 SoC (750 MHz)
-   128 MiB of RAM (DDR2)
-   16 MiB of flash (SPI)
-   5x 1 Gbps Ethernet (1x WAN + 4x LAN)
-   2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
-   10x LED, 2x button
-   UART header on PCB

Flash instructions:
1.  Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
    via web interface.

Flash instructions using TFTP recovery:
1.  Plug PC to one of the LAN ports
2.  Set PC to fixed IP address 192.168.0.66
3.  Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
    TFTP root directory
4.  Turn on the router with the reset button pressed for about 15 secs
5.  Release the button and wait about 150 secs to complete flashing

Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
2018-12-27 14:06:38 +01:00
Christian Lamparter
87c5fd348d ath79: fix pinmux reg size for QCA955x
The range of pinmux reg property "<0x1804002c 0x40>" for QCA955x
SoC does not includes GPIO_FUNCTION register.

Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-24 19:18:07 +01:00
INAGAKI Hiroshi
c566439c9b ath79: add support for NEC Aterm WG800HP
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
  - Vcc, GND, NC, TX, RX from SoC side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-24 19:18:07 +01:00
INAGAKI Hiroshi
10a54e1442 ath79: fix pinmux reg value for QCA956x
The range of pinmux reg property "<0x1804002c 0x40>" for QCA956x SoC
does not includes GPIO_FUNCTION register.

If the device uses "&jtag_disable_pins", this causes the following
errors:

[    1.982937] pinctrl-single 1804002c.pinmux: mux offset out of range: 0x40 (0x40)
[    1.990622] pinctrl-single 1804002c.pinmux: could not add functions for pinmux_jtag_disable_pins 64x

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-24 19:18:07 +01:00
Mathias Kresin
38cae44e51 ath79: replace cameo-factory with existing build commands
Use pad-offset and append-string to create the cameo factory images for
the D-LINK DIR-825 C1/DIR-835 A1 factory images.

Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-17 23:21:40 +01:00
Christian Lamparter
b9501cecde ath79: dts: Remove newly added default-state=off property
I'm afraid that this will be "one of many" patches to come.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 14:22:28 +01:00
Christian Lamparter
f54ac91ef5 ar71xx/ath79: switch devices to the -ct driver and firmware
Since commit 61b5b4971e ("mac80211: make ath10k-ct the default ath10k")
select ath10k-ct and the -ct firmwares by default.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 14:22:28 +01:00
Petr Štetiar
0d23fd2ab2 treewide: dts: Remove default-state=off property from all gpio LED nodes
>From the Documentation/devicetree/bindings/leds/common.txt:

- default-state : The initial state of the LED. Valid values are "on", "off",
  and "keep". If the LED is already on or off and the default-state property is
  set the to same value, then no glitch should be produced where the LED
  momentarily turns off (or on). The "keep" setting will keep the LED at
  whatever its current state is, without producing a glitch.  The default is
  off if this property is not present.

So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:16:28 +01:00
Karl-Felix Glatzer
1e4ee63cc8 ath79: add support for TP-Link Archer A7
This patch adds support for TP-Link Archer A7

Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) SoC internal
  - 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
  - Vcc, GND, RX, TX from ethernet port side
  - 115200n8

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
   root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
   and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing

Changes since first revision:

  - Flash instructions using stock image webinterface
  - Changed "Version 5" in model string to "v5"
  - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
    and qca9563_tplink_archer-a7-v5.dts
  - Firmware image is now build with dynamic partitioning
  - Default to ath10k-ct

Changes since second revision:
  - Changed uboot@0 to uboot@20000 in DTS file
  - Fixed ordering issue in board led script
  - Specify firmware partition format in DTS file
  - Rebased Makefile device definition on common
    Device/tplink-safeloader-uimage definition
  - Merged switch section in network script
    (same configuration as tplink,tl-wdr3600
    and tplink,tl-wdr4300)

Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-17 08:09:13 +01:00
Petr Štetiar
d9753f0ec5 ath79, brcm63xx: Fix debounce-interval properties in gpio-keys-polled nodes
This patch fixes wrong usage of debounce-interval subnode property of
gpio-keys-polled nodes, which was used inproperly in parent node, but it
belongs to the subnodes, excerpt from the docs:

 Optional subnode-properties:
     - debounce-interval: Debouncing interval time in milliseconds.
       If not specified defaults to 5.

And the docs are up to date as the source code matches that description
as well:

 if (fwnode_property_read_u32(child, "debounce-interval",
                              &button->debounce_interval))
         button->debounce_interval = 5;

While at it, I've also re-formatted gpio-keys-polled nodes, usually just
adding new lines after every key subnode.

Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Cc: Matt Merhar <mattmerhar@protonmail.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:05:03 +01:00
Petr Štetiar
7bd2595b67 ath79: ag71xx: Fix code formatting in ag71xx_probe
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:04:19 +01:00
Petr Štetiar
a29df78c9f ath79: ag71xx: Unify debug output with ar71xx and make debugging easier
Currently it's quite hard to diff debugging output between ar71xx and
ath79, so this patch tries to improve it by adding the same
ag71xx_dump_regs function and placing debugging output from the
registers to relatively same places.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:04:05 +01:00
Sebastian Kemper
6c3c4436ee ath79: add d-link dir-825-c1 and dir-835-a1
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.

The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.

https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1
https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1

Installation:

1. Connect to the web interface of the vendor firmware (usually
   listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
   selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.

Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
2018-12-17 00:21:34 +01:00
Marcin Jurkowski
3c3eaa57d9 ath79: add support for TP-Link TL-WR842N/ND v1 router
This ports support for TP-Link TL-WR842N/ND v1 from ar71xx.

CPU: Atheros AR7241 400 MHz
RAM: 32 MiB
FLASH: 8 MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9287
LED: SYS, WiFi, LAN, WAN, 3G, QSS
BTN: WiFi, Reset/WPS

AR71xx target used "tl-mr3420" as board id so force flag is needed
if upgrading from old target.

Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
2018-12-15 21:35:45 +01:00
Mathias Kresin
0fdfdaef2d ath79: fix dtc compiler warnings
The qca9557/qca956x reset-controller aren't a simple bus. A simple bus
would require node unit addresses.

Add the node unit addresses for the qca9557 usb phys. Add the regs for
the USB_PWRCTL and USB_CONFIG registers even not yet used.

Fix the wrong ar7100 pcie controller node unit address as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 12:28:26 +01:00
Daniel F. Dickinson
32bc733796 ath79: dts: Use PowerCloud CAP324 bicolor status LED
PowerCloud Systems CAP324 has a bicolor power LED and OpenWrt DTS files /
base files support using both colours to better inform user of state
and to better match stock firmware, so use green power to indicate
normal operation.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-12-06 20:26:57 +01:00
INAGAKI Hiroshi
3358cae523 ath79: add support for I-O DATA WN-AG300DGR
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.

WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.

There is no eeprom data for 5 GHz wlan in "art" partition.

Specification:

- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
  - 2.4 GHz: SoC internal
  - 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-06 20:26:57 +01:00
Chuanhong Guo
9dd7147f6b ath79: add support for Winchannel WB2000
WB2000 is a dual-band 11N AP using AR9344.
The factory firmware used the original DB120 partition table
with a small kernel partition at the end of firmware and the
kernel will easily get oversized in the future. Since it has
to be flashed using UART I also swapped kernel/rootfs and
changed the default load address.

Specification:

- SoC: Atheros AR9344
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 10/100/1000 Mbps (Atheros AR8035)
- 2x USB 2.0
- WIFI: AR9344(2G) + AR9382(5G)
- RTC: DS1338

Known issue:
5G ath9k led doesn't work due to commit ccab68f.

Flash instruction:
Set up a TFTP server on your computer and configure static IP.
Connect UART (J11 TX/GND/RX) and press any key to enter U-boot
shell.
1. Change the default boot command:
   setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000'
   saveenv
2. Set your router ipaddr and server ipaddr. e.g.:
   setenv ipaddr 192.168.1.1
   setenv serverip 192.168.1.50
3. Load and flash the firmware:
   tftp 0x80060000 fw.bin
   erase 0x9f050000 +$filesize
   cp.b $fileaddr 0x9f050000 $filesize
4. Reset your router:
   reset

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Drop the i2c node unit address. Move the ath9k-leds node out of the spi
node, it doesn't belong there. Add the #gpio-cells property to the pci
wifi node. All fix dtc compiler warnings]
Signed-off-by: Mathias Kresin <dev@kresin.me>

merge
2018-12-06 20:26:30 +01:00
INAGAKI Hiroshi
e0c55760e6 ath79: fix ethernet configurations for I-O DATA ETG3-R
This commit fixes several issues in eth0 on ETG3-R, and solve slowdown
in NA(P)T speed.

- add gmac-config with correct configurations
- fix pll-data value

And I added ref clock-frequency.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-06 17:44:14 +01:00
Mathias Kresin
6e626477d5 ath79: drop unused mtd splitter
Neither the seama nor the wrgg splitter are used at the moment. Drop
them for now to not bloat the target from the beginning.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:47 +01:00
Mathias Kresin
dacd962cfd ath79: remove duplicate image build variables
Remove image build variables which are set to the same value as the
default image build recipe.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:22 +01:00
Mathias Kresin
9d8fcab77a ath79: fix GL.iNet GL-AR300M sysupgrade
The userspace boardname derived from the dts compatible was out of sync
with the expected board added to the image metadata. This way a
sysupgrade is refused.

Sync the userspace boardname and the baordname used in the image metdata
to allow a seamless sasupgrade.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:22 +01:00
Mathias Kresin
8d6f128d39 ath79: add SoC or family compatible
Add missing SoC specific compatibles and/or inherit the family
compatibles like "ubnt,xm".

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:22 +01:00
David Bauer
adfc8d8eca ath79: add AVM EVA firmware partition compatible
This commit adds firmware partition compatible for the
AVM FRITZ!Box 4020 and AVM FRITZ!WLAN Repeater 300E.

This allows to select the correct mtdsplit parser
instead of trying all available ones one by one.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-06 13:28:22 +01:00
Petr Štetiar
bc41fb7efe ath79: Define firmware partition format to all boards where applicable
Parsing "firmware" partition (to create kernel + rootfs) was implemented
using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With
recent upstream mtd changes we can do it in a more clean way for DTS
targets. It just requires adding a proper "compatible" string to the
"firmware" partition node.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-06 13:28:22 +01:00
Chuanhong Guo
c36ec336a3 ath79: rename qca9533.dtsi to qca953x.dtsi
qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE.
Rename the misleading dtsi names and fix the SoC type of gl-ar300m.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[apply the changes for the gl-x750 as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Petr Štetiar
9da6cd40eb apm821xx, ath79, ipq40xx, ipq806x, lantiq, ramips: base-files: Use generic diag.sh
I wanted to add status LEDs support to my imx6 based board and have found out,
that I could use diag.sh script found in ramips platform, which seems to be
also shared in a few other platforms:

 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh

And @chunkeey suggested to me, that I can also add lantiq, ipq806x and
apm821xx to the list of platforms which could share this generic
diag.sh.

I've extended the base diag.sh in a way, that if it detects any of the
DTS LED aliases, then it would use the generic DTS set_led_state code.
The code in platform's diag.sh has moved to base-files package in this
commit:

 base-files: diag.sh: Make it more generic towards DTS so it could be reused

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
2018-12-06 08:42:40 +01:00
Russell Senior
73127a878d ath79: add support for Ubiquiti AirRouter
Indoor low-power router with 2.4 GHz radio

CPU:    Atheros AR7241 rev 1
RAM:    32 MB
Flash:  8 MB NOR SPI
Switch: Atheros AR7240
Ports:  1x WAN, 4x LAN 10/100 Ethernet
WLAN:   Atheros AR9285 (2.4 GHz)
USB:    1x USB2 host port

Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.

UART settings: 115200, 8N1

                LEDs
        +--------------------------
        |
        |
        |
        |
        |
        |
        |
        |
    VCC | x x
     RX | * x
        | x x
        | x x
     TX | * x
    GND | * x
        |
        |
        |
        |
        +--------------------------
                ETHERNET PORTS

Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-03 07:58:56 +01:00
Russell Senior
20ec6af15e ath79: split ubnt outdoor device leds into separate dtsi
Move common LED configuration into a separate includible dtsi.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-03 07:58:49 +01:00
Petr Štetiar
1576666d67 ath79: ubnt-xw: Change DTS license to GPL-2.0-or-later OR MIT
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-29 13:10:50 +01:00
Petr Štetiar
9f563267d2 ath79: ubnt-bullet-m-xw: Change DTS license to GPL-2.0-or-later OR MIT
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-29 13:10:38 +01:00
Rosy Song
31469aebd4 ath79: add support for ROSINSON WR818 board
This commit adds support for the ROSINSON WR818 WiFi-Router

SoC:    Qualcomm Atheros QCA9563,
FLASH:  Winbond W25Q128FV 16MBytes,
WiFi:   QCA9563 b/g/n 3x3 450Mbit/s,
USB:    1x USB 2.0 Type A, 1x USB2.0 Type C,
IN:     WPS/Reset button GPIO1,
OUT:    Power LED red, Internet LED red, WLAN LED red,
        LAN1 LED red, LAN2 LED red, System LED red,
UART:   RX-GPIO18, TX-GPIO22,

Tested and working:
    - Ethernet (LAN + WAN)
    - WiFi
    - OpenWRT sysupgrade
    - Button
    - LEDs

Installation of OpenWRT from vendor firmware:
    - Connect to the Web-interface at http://192.168.1.1
    - Go to "Administration" -> "Firmware Upgrade"
    - Upload the OpenWrt sysupgrade image

Signed-off-by: Rosy Song <rosysong@rosinson.com>
2018-11-27 21:11:54 +01:00
Mathias Kresin
7574781337 ath79: merge glinet gl-x750 dtsi and dts
The board doesn't come in different flash type flavours, hence there is
no need to keep a dtsi + dts for this purpose.

While at it, fix some whitespace issues.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-27 21:11:54 +01:00
Mathias Kresin
68d77241cd ath79: rename glinet x750
The boardname is gl-x750 and is already used for the led names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-27 21:11:54 +01:00
David Bauer
a734450d6f ath79: add Archer C58/C59 partition compatible
This commit adds firmware partition compatible for the
TP-Link Archer C58 v1 and Archer C59 v1.

Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 21:27:17 +01:00
David Bauer
df2e6b64d1 ath79: add firmware partition compatible for OCEDO
This commit adds firmware partition compatible for the
OCEDO Raccoon and OCEDO Koala.

Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 21:26:56 +01:00
INAGAKI Hiroshi
37c848810c ath79: specify "firmware" partition format for I-O DATA devices
Specify firmware partition format (denx,uimage) by compatible string
for I-O DATA devices.

affected devices (&run tested)

- WN-AC1167DGR
- WN-AC1600DGR2

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 21:26:07 +01:00
INAGAKI Hiroshi
fa1a120a1a ath79: specify "firmware" partition format for ELECOM WRC-300GHBK2-I
Specify firmware partition format (denx,uimage) by compatible string
for ELECOM WRC-300GHBK2-I.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 21:26:06 +01:00
Mathias Kresin
f4abc962ec ath79: fix shebang
The shebang was accidentally changed with 9989fd5154 ("ath79: add
support for GL-iNet GL-X750").

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 19:40:31 +01:00
INAGAKI Hiroshi
879f2ef7c0 ath79: modify mtd partitions for Buffalo BHR-4GRV2
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.

In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.

0x50000                       0xe80000        0xff0000
  +-------------------------------+--------------+
  |            rootfs             |    kernel    |
  |           (14528k)            |    (1472k)   |
  +-------------------------------+--------------+

After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.

0x50000                                       0xff0000
  +----------------------------------------------+
  |                   firmware                   |
  |                   (16000k)                   |
  +----------------------------------------------+

However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".

This commit requires new flash instruction instead of the old one.

Flash instruction using initramfs image:

1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
  /dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
  fw_setenv ipaddr 192.168.12.1
  fw_setenv serverip 192.168.12.10
  fw_setenv ethaddr 00:aa:bb:cc:dd:ee
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing

And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 12:28:17 +01:00
Robert Marko
d6e92b18d9 ath79: Remove source-only flag
Remove the source-only flag from ath79, its supposed to replace ar71xx after next stable release but buildbots are not currently generating images for it.
So in order to expand testing as much as possible and prepare for moving to ath79 lets enable the buildbots to actually build the target.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-11-26 12:24:54 +01:00
INAGAKI Hiroshi
83f08aebb1 ath79: specify "firmware" partition format for Buffalo devices
Specify firmware partition format (denx,uimage) by compatible string
for Buffalo devices.

affected devices (&run tested):
- BHR-4GRV
- WHR-G301N
- WZR-HP-AG300H
- WZR-HP-G302H A1A0
- WZR-HP-G450H (WZR-450HP)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 12:09:25 +01:00
David Bauer
946ffe470d ath79: add support for Archer C58/C59 v1
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.

CPU:   Qualcomm QCA9561
RAM:   64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi:  QCA9561 bgn 3x3:3
       QCA9888 nac 2x2:2
LED:   Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
       Only C59: USB
BTN:   WPS, WiFi, Reset

Installation
------------

Via Web-UI:
Update factory image via Web-UI.

Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.

Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 12:05:45 +01:00
Luo chongjun
9989fd5154 ath79: add support for GL-iNet GL-X750
this patch adds supports for GL-X750.

Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)

Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2018-11-26 12:05:45 +01:00
Petr Štetiar
d42a7c4699 ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:

 All future airOS versions will be signed in this way and not allow
 unsigned firmware to be loaded except via TFTP.

U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:

 Hit any key to stop autoboot:  0
 Setting default IP 192.168.1.20
 Starting TFTP server...
 Receiving file from 192.168.1.25:38438
 Received 4981148 bytes
 Firmware check failed! (1)

By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:

 Received 3735964 bytes
 Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt
 Setting U-Boot environment variables
 Un-Protected 1 sectors
 Erasing Flash.... done

Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and
Nanostation M5 XW (ae6xe).

1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:44 +01:00
Petr Štetiar
db4b6535f8 ath79: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions

 A) Serial console, U-Boot and TFTP

   1. Connect to serial header J1 on the PCB
   2. Power on device and enter U-Boot console
   3. Set up TFTP server serving an OpenWrt initramfs build
   4. Load initramfs build using the command tftpboot in the U-Boot cli
   5. Boot the loaded image using the command bootm
   6. Copy squashfs OpenWrt sysupgrade build to the booted device
   7. Use mtd to write sysupgrade to partition "firmware"
   8. Reboot and enjoy

 B) Experimental factory image flashing over SSH from airOS v6.1.7

   1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware
      no other airOS version is currently supported
   2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing
   3. cd ubnt-bullet-m2hp-openwrt-flashing
   4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:38 +01:00
Rafał Miłecki
18c5e7ba91 ath79: specify "firmware" partition format for Ubiquiti UniFi
This affects:
1. Ubiquiti UniFi-AC-LITE/LR
2. Ubiquiti UniFi-AC-PRO
3. Ubiquiti UniFi-AC-MESH
4. Ubiquiti UniFi-AC-MESH PRO

Succesfully tested on UniFi AP AC Pro.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 19:04:29 +01:00
Hannu Nyman
3e19113d5d ath79: specify "firmware" partition format for WNDR3700 and v2
Specify the new "firmware" partition format for Netgear WNDR3700
and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third
device in the family.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-11-24 13:15:55 +01:00
Rafał Miłecki
c8a005fefd ath79: specify "firmware" partition format for TP-LINK Archer C7 v2
With this change it doesn't require trying parsers one by one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 12:46:00 +01:00
Rafał Miłecki
ffd082aa38 ath79: specify "firmware" partition format for Netgear WNDR3800
It doesn't require trying parsers one by one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 08:46:59 +01:00
Koen Vandeputte
c764b2b531 kernel: bump 4.14 to 4.14.79
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-05 16:00:00 +01:00
Mathias Kresin
374e646724 ath79: fix PQI Air Pen support
Use the correct dts filename. It has to be <soc>_<manufacturer>_<device>.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-28 11:03:49 +01:00
YuheiOKAWA
27eae6597e ath79: add support for PQI Air Pen
SoC: AR9330 (or AR9331 revision?)
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Flash 8MiB. (factory is dual image)
1. write image is use half 4MiB size from factory.
  write initramfs image to mtd6 and mtd7.
2. change next boot setting. next is mtd6 boot.
  echo -ne "\x01" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

3. rewrite sysupgrade image.
  change next boot setting. next is mtd4.
  echo -ne "\x00" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

OEM mtd.
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "ART"
mtd3: 00010000 00010000 "NVRAM"
mtd4: 00140000 00010000 "uImage"
mtd5: 00280000 00010000 "rootfs"
mtd6: 00140000 00010000 "uImage2"
mtd7: 00280000 00010000 "rootfs2"
mtd8: 00010000 00010000 "CONF"

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-10-28 10:59:14 +01:00
Roger Pueyo Centelles
23f9b2d9a9 ath79: Add support for Ubiquiti LiteAP ac (LAP-120)
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.

CPU:    Atheros AR9342 SoC
RAM:    64 MB DDR2
Flash:  16 MB NOR SPI
Ports:  1 GbE port (PoE in)
WLAN:   5 GHz QCA899X (PCI)

The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).

Installation procedure is the same as the NanoStation [loco] AC:

1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-10-28 10:59:09 +01:00
Fabio Bettoni
ddc11c3932 ar71xx/ath79: fix mtd corruption
In commit fec8fe8069 ("kernel: bump 4.9 to 4.9.116") [1], the following patch for removed:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch

This patch contained fixes for both write and erase functions.

While the chip-detects for erase got fixed upstream [2],
some modifications are still required, even with the fixes applied.

While at it, also apply the same fix for target ath79,
which suffers the same issue.

Not doing so results in following errors seen:

Collected errors:
 * pkg_write_filelist: Failed to open //usr/lib/opkg/info/luci-lib-ip.list: I/O error.
 * opkg_install_pkg: Failed to extract data files for luci-lib-ip. Package debris may remain!
 * opkg_install_cmd: Cannot install package luci-ssl.
 * opkg_conf_write_status_files: Can't open status file //usr/lib/opkg/status: I/O error.

[    0.780920] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    8.406396] jffs2: notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.423476] mount_root: switching to jffs2 overlay
[  270.902671] jffs2: Write of 1989 bytes at 0x005ce6f8 failed. returned -5, retlen 962
[  270.931965] jffs2: Write of 1989 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.939631] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.950397] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.957838] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.968584] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.976027] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.986735] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.994225] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero

[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=fec8fe806963c96a6506c2aebc3572d3a11f285f
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.9.133&id=a0239d83e1cb60de5e78452d4708c083b9e3dcbe

Fixes: fec8fe8069 ("kernel: bump 4.9 to 4.9.116")
Signed-off-by: Fabio Bettoni <fbettoni@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-17 18:55:37 +02:00
Mathias Kresin
80c61c161a treewide: use wpad-basic for not small flash targets
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-16 15:07:41 +01:00
Koen Vandeputte
f983956a8b kernel: bump 4.14 to 4.14.75
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-10 14:45:11 +02:00
David Bauer
35c314bdb2 ath79: add Fritz!Box 4020 switchconfig
In contrast to ar71xx, uci switchconfig is missing in the ath79 target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-10-07 17:26:30 +02:00
David Bauer
5815bb2e41 ath79: add support for TP-Link TL-WA901ND v2
This commit adds support for the TP-Link TL-WR901ND v2 access point.

CPU:   Atheros AR9132 400MHz
RAM:   32MB
FLASH: 4MiB
WiFi:  Atheros AR9103 3x3:2 bgn
LED:   Power (static on)
       LAN (controlled by PHY)
       SYS, WiFi, QSS toggleable
BTN:   Reset, QSS

Installation:
Upload the factory image via the vendor-GUI.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-10-07 15:49:25 +02:00
INAGAKI Hiroshi
6d1abbcab4 ath79: add support for Buffalo WZR-HP-G302H A1A0
Buffalo WZR-HP-G302H is a 2T2R 2.4 GHz 11n router, based on Atheros
AR7242.

It is Japanese market model of WZR-HP-G300NH2, but there are some
diffrences. This commit is based on WZR-HP-G300NH2 in ar71xx.
And, G302H has several hardware versions and hardware is different
dependent on the versions. This commit adds support for "A1A0"
version.

Specification:

- Atheros AR7242
- 64 MB of RAM (DDR2)
- 32 MB of Flash
  - 2x 16 MB SPI-NOR flash
- 2.4 GHz 2T2R wifi
  - Atheros AR9283
- 5x 10/100/1000 Mbps Ethernet
  - Atheros AR8316
- 7x LEDs, 5x keys
  - LED: 1x gpio-leds, 6x ath9k-leds
  - key: 3x buttons, 2x slide switches
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Boot WZR-HP-G302H normaly and connect the computer to its LAN port
2. Access to "http://192.168.11.1/" and move to firmware update page
("ファーム更新")
3. Select the OpenWrt factory image and click update ("更新実行")
button to perform firmware update
4. Wait ~200 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-10-07 15:44:19 +02:00
INAGAKI Hiroshi
d745eac636 ath79: add hwver parameter to buffalo-tag
In order to be able to set the value of "hardware version" other than
"3", I added the "hwver" parameter.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-10-07 15:44:19 +02:00
Robert Marko
adbd9d1f1f ath79: Add support for TP-Link TL-WR842N-v2
This PR adds support for TP-Link TL-WR842N-v2 router which is supported by ar71xx to ath79.

This is a low cost model with following specs:

CPU: Atheros AR9341 SoC
RAM: 32 MB DDR1
Flash: 8 MB NOR SPI
Switch: Internal AR9341 5 port 10/100 Mbit
Ports:  5x 10/100 Mbit(1x WAN, 4x LAN)
USB: 1x USB2.0
WLAN: 2.4 GHZ AR9341

Installation:

Simply flash the factory image through stock firmware WEB UI.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-10-07 15:44:19 +02:00
Mathias Kresin
b09992a7d9 ath79: fix build warning
The image build code for the Ubiquiti Nanostation AC series adds the
factory image as to be build image. The same is already done by an
included recipe which results into an expanded IMAGE variable of:

  IMAGES = sysupgrade.bin factory.bin factory.bin

The build system doesn't like these duplicates and issues the following
warning:

  Makefile:82: warning: overriding recipe for target...

Get remove the duplicate factory image to get rid of the warning.

Fixes: 5736af8024 ("ath79: Add support for Ubiquiti NanoStation AC loco")
       fa3c2676ab ("ath79: Add support for Ubiquiti Nanostation AC")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 15:44:19 +02:00
Tobias Schramm
fa3c2676ab ath79: Add support for Ubiquiti Nanostation AC
5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio

CPU:    Atheros AR9342 SoC
RAM:    64 MB DDR2
Flash:  16 MB NOR SPI
Switch: QCA8334
Ports:  2 GbE ports (1x PoE in, 1x PoE passthrough)
WLAN:   5 GHz QCA899X (PCI) and 2.4 GHZ AR9342

Successor to the old NanoStation M5 with AC wireless.

The integrated QCA899X is a Ubiquiti branded part with modified vendor and
product id (0777:11ac9).

Serial

Serial settings: 115200, 8N1

* = plated through hole
0 = nylon screw

      [Top of device]
+--------------------------+
|    [label]               |
|  0                       |
|                    0     |
|         [ubnt]           |
|         [logo]  3V3  *   |
|                  TX  *   |
|                  RX  *   |
|                 GND  *   |
|                          |
|                      *   |
|                      *   |
|                      *   |
|                      *   |
|    0                     |
|                 0        |
|                          |
|                          |

Installation

1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-10-07 10:46:20 +02:00
Tobias Schramm
5736af8024 ath79: Add support for Ubiquiti NanoStation AC loco
Atheros AR9342, 16 MB flash, 64 MB RAM

Successor to the old NanoStation M5 loco with AC wireless.

Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti
branded and customized QCA988X with vendor id 0777 and device id 11ac for
AC wireless.

Installation

1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-10-07 10:46:20 +02:00
Tobias Schramm
bc5761f90b ath79: Add generic device tree for Ubiquiti WA boards
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-10-07 10:46:20 +02:00
INAGAKI Hiroshi
4b9882eb92 ath79: fix MAC address for Buffalo BHR-4GRV
I added mtd-mac-address for WZR-HP-G450H and BHR-4GRV in
1df1ea4d7e, but that address in ART is
incorrect for BHR-4GRV.

WZR-HP-G450H has wlan eeprom and MAC address in ART, but BHR-4GRV
has only MAC address in ART.

- WZR-HP-G450H
  - eeprom: 0x1000
  - MAC:    0x1002

- BHR-4GRV
  - MAC:    0x0

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-10-07 10:46:20 +02:00
Koen Vandeputte
7bfe757bc4 kernel: bump 4.14 to 4.14.73
Refreshed all patches.

Removed upstreamed:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-02 13:44:36 +02:00
INAGAKI Hiroshi
81f7bdcb8d ath79: add support for Buffalo BHR-4GRV
Buffalo BHR-4GRV is a wired router, based on Atheros AR7242.

Specification:

- Atheros AR7242
- 64 MB of RAM
- 32 MB of Flash
  - 2x 16 MB SPI-NOR flash
- 5x 10/100/1000 Mbps Ethernet
- 3x LEDs, 2x keys
- 1x USB 2.0 Type-A
- UART header on PCB
  - JP1: Vcc, GND, TX, RX from reset button side

Flash instruction using factory image:

1. Boot the BHR-4GRV normaly and connect the computer to its LAN port
2. Access to
"http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html"
with user "bufpy" and password "otdpopy"
3. Select the OpenWrt factory image and click "OK" button to perform
firmware upgrade
4. Wait ~200 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-09-26 20:35:07 +02:00
INAGAKI Hiroshi
1df1ea4d7e ath79: fix support for Buffalo WZR-HP-G450H and split to dts/dtsi
There are many parts that are incorrect or missing in the current
code for Buffalo WZR-HP-G450H in ath79, so its support is broken.

I fixed that issues and split to dts/dtsi files to add support for
Buffalo BHR-4GRV.

And WZR-450HP has the same hardware as WZR-HP-G450H, so I change the
device name to "WZR-HP-G450H/WZR-450HP".

Specification:

- Atheros AR7242
- 64 MB of RAM
- 32 MB of Flash
  - 2x 16 MB SPI-NOR flash
- 3T3R 2.4 GHz wifi
  - SoC internal
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 5x keys
- 1x USB 2.0 Type-A
- UART header on PCB
  - JP1: Vcc, GND, TX, RX from reset button side

Flash instruction using factory image:

1. Boot the WZR-HP-G450H (or WZR-450HP) normaly and connect the computer
to its LAN port
2. Access to
"http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html"
with user "bufpy" and password "otdpopy"
3. Select the OpenWrt factory image and click "OK" button to perform
firmware update
4. Wait ~200 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-09-26 20:35:07 +02:00
INAGAKI Hiroshi
b6e6785c88 ath79: fix wrong pll-data value for I-O DATA WN-AC-DGR devices
The pll-data value "0x56000000" is wrong for I-O DATA WN-AC1600DGR2
and WN-AC1167DGR, so there was a problem of slowing down the speed of
ethernet.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-09-26 20:35:07 +02:00
John Crispin
61b5b4971e mac80211: make ath10k-ct the default ath10k
We select ath10k-ct by default, but it is still possible to build
the upstream version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
2018-09-26 16:39:44 +02:00
Koen Vandeputte
e9d92bf1e1 kernel: bump 4.14 to 4.14.72
Refreshed all patches.

Removed upstreamed:
- 203-MIPS-ath79-fix-restart.patch
- 0013-MIPS-ath79-fix-system-restart.patch
- 180-earlycon-initialize-port-uartclk-based-on-clock-frequency-property.patch
- 181-earlycon-remove-hardcoded-port-uartclk-initialization-in-of_setup_earlycon. patch
- 700-1-6-e1000e-Remove-Other-from-EIAC.patch
- 700-2-6-Partial-revert-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch
- 700-3-6-e1000e-Fix-queue-interrupt-re-raising-in-Other-interrupt.patch
- 700-4-6-e1000e-Avoid-missed-interrupts-following-ICR-read.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-26 15:54:18 +02:00
Robert Marko
b9ba32b2e3 ath79: Fix GL-AR300M USB trigger
Correct a typo preventing USB trigger to work on AR300M.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-09-22 21:20:48 +02:00
David Bauer
c6ecb83db4 ath79: flag FritzBox 4020 buttons as active low
Buttons of AVM FritzBox 4020 are incorrectly flagged as active high.

This was an oversight as RFKill button was working as expected even
with incorrectly flagged GPIO.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-09-22 19:26:26 +02:00
Koen Vandeputte
0dbdb476f3 kernel: bump 4.14 to 4.14.71
Refreshed all patches.

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-21 13:23:16 +02:00
Koen Vandeputte
0cda4af005 kernel: bump 4.14 to 4.14.70
Refreshed all patches.

Added new patch:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch

This fixes a bug introduced in upstream 4.14.68 which caused targets using
ubifs to produce file-system errors on boot, rendering them useless.

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-17 15:47:44 +02:00
Lech Perczak
4f93342d92 ath79: ubnt-xm: add rssileds package
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM family.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-09-10 09:58:31 +02:00
Lech Perczak
e440a9d73f ath79: ubnt-xm: create RSSI monitor on wlan0
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM family, the mapping for rssileds monitor was omitted
by mistake. Therefore create the mapping, so RSSI LEDs work without
additional configuration, after starting rssileds service.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-09-10 09:58:31 +02:00
Bernhard Frauendienst
480bf28273 ath79: add support for Buffalo WZR-HP-AG300H
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2

Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
    WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
    Diag red, Movie Engine blue, USB green)

It is already supported by the ar71xx target.

For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>

Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.

Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image

Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
  - via TFTP rescue
  - via factory image
    - on firmware v1.77 (28-05-2012)
    - on pro firmware v24SP2 r30356 (26-03-2018)
  - via sysupgrade from ar71xx
    (wlan devices don't work because of new names)
  - via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)

Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-09-10 09:35:07 +02:00
INAGAKI Hiroshi
7768f11534 ath79: add support for ELECOM WRC-300GHBK2-I
ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4 GHz wifi
  - SoC internal
- 5x 10/100/1000 Mbps Ethernet
- 3x LEDs, 4x keys(connected to GPIO: 3x)
- UART header on PCB
  - TX, GND, RX, Vcc from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Boot the WRC-300GHBK2-I normaly and connect the computer to its
LAN port
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新 手動更新(アップデート)")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, execute "mtd erase firmware" to
erase stock firmware and execute sysupgrade with squashfs-sysupgrade
image for WRC-300GHBK2-I
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-09-10 09:30:28 +02:00
Christian Lamparter
745dee11ac ath79: add support for WD My Net Wi-Fi Range Extender
This patch ports over support for the device from ar71xx.

SOC:	AR7370 (Wasp - AR9344 rev2 0001974c)
RAM:	Winbond W9725G6KB-25 32MiB
FLASH:	Winbond 25Q64FVSIG 8MiB
WLAN:	AR9380 Dual-Band 802.11abgn 3x3:3
INPUT:	WPS, RESET button (hardware on/off toggle button)
LED:    Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high)
Serial: Header Next to the winbond flash chip (labeld JP1)
	Pinout is GND - NC - RX - TX - 3V3 (JP1)
	The Serial setting is 115200-8-N-1.

- Installation via uboot's upgrade command
  0. attach serial cable
  1. interrupt uboot and enter "upgrade code.bin" into
      the u-boot prompt
	ar7240> upgrade code.bin

  2. rename openwrt...sysupgrade.bin to code.bin on PC
  3. run a tftp-client on the PC
	 (shell)$ tftp 192.168.1.230
	 binary
	 put code.bin
  4. wait for the device to finish

	[...]
	Copy buff to Flash from 0x9f040000 length 0x79f000
	Copy to Flash... write addr: 9f040000
	done

  5.  enter "go" in the u-boot prompt
	ar7240> go

- TFTP ramdisk image boot from the uboot prompt
  (tftp server defaults to serverip 192.168.1.254)
	=> tftpboot 81000000 initramfs.bin
	=> bootm

Tested and working:
	- LEDs
	- Buttons
	- Ethernet
	- Wi-Fi
	- OpenWRT sysupgrade

For flashing and debricking information see:
<https://openwrt.org/toh/wd/rext>

Users coming from ar71xx can use sysupgrade too. But I highly
advise to no save the old configuration and start from a clean
state.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-09-10 09:07:41 +02:00
Christian Lamparter
cd9c2492c1 ath79: port cybertan_part from ar71xx
This patch ports the cybertan_part code from ar71xx and converts the
driver to a DT-supported mtd parser. As a result, it will no longer
add the u-boot, nvram and art partitions, which were never part of
the special Cybertan header.

Instead these partitions have to be specified in the DT, which has the
upside of making it possible to add properties (i.e.: read-only), labels
and references to these important partitions.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-09-10 09:07:11 +02:00
Matt Merhar
9c26def64a ath79: fix unaligned access panic in ag71xx_mdio_probe
Without "syscon" being present in an ag71xx ethernet DT node's
compatible property, a panic occurs at boot during probe citing
"Unhandled kernel unaligned access".

With this modification, the panic no longer occurs and instead the probe
simply fails, allowing the boot process to continue.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-09-06 21:35:53 +02:00
Matt Merhar
b672550b32 ath79: add syscon compatible property to ar7100 ethernet nodes
This adds "syscon" to the compatible properties for the eth0/eth1 nodes
in ar7100.dtsi.

Without this, a kernel panic is encountered on boot with some ar7100
boards. This for some reason wasn't an issue for the WNDR3800, which
uses a Realtek switch chipset, but the panic was encountered on the
RouterStation Pro (using an AR8216 switch) and some other boards that
haven't yet been merged.

The panic message mentions an unaligned access and happens in
ag71xx_mdio_probe in drivers/net/ethernet/atheros/ag71xx/ag71xx_mdio.c.

Even if the unaligned access is fixed, the ag71xx_mdio probe still fails
without the "syscon" property.

This was already being worked around in
ar7161_ubnt_routerstation-pro.dts by overriding the compatible property,
so this commit removes that as well.

All of the other ath79 .dtsi already have this property, so no changes
are needed elsewhere.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-09-06 21:35:53 +02:00
Koen Vandeputte
01793e8752 kernel: bump 4.14 to 4.14.67
Refreshed all patches.

Removed upstreamed patches:
- 037-v4.18-0008-ARM-dts-BCM5301x-Fix-i2c-controller-interrupt-type.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-28 23:05:39 +02:00
John Crispin
fd20fdd0b8 ath79: fix remove irq code from pci driver patch
This patch got mangled in the void while rebasing it.

Signed-off-by: John Crispin <john@phrozen.org>
2018-08-28 11:58:50 +02:00
Dmitry Tunin
8132e06247 ath79: fix ar7100 PCI IRQ handling
Currently all PCI devices get the same IRQ that affects performance badly.

This commit adresses this problem and cleans the code.

ar7100 has a special PCI interrupt controller@18060018 that works exactly
the same way as misc interrupt controller.

This patch does the following:

1. Defines pci-intc interrupt controller@18060018 in dtsi.
2. Removes interrupt-controller property from PCI node.
3. Sets a correct interrupt mask for PCI devices.
4. Removes all IRQ handling code from the PCI driver.

"qca,ar7100-misc-intc" should be used as the compatible property, becuase on ar7100
the controlled status register is read-only and the ack method used in
"qca,ar7240-misc-intc" won't work properly.

There are two very minor downsides of this patch that don't affect perormance:

1. We allocate an IRQ domain of 32 IRQ, whan we need only 5. But ar7100 aren't tiny un terms of RAM
and that is not very important and can be tuned if we implement "nr-interrupts" property".

2. It reuses the same irg chip name "MISC" for both controllers.

Run tested on DIR-825 B1.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2018-08-28 11:26:53 +02:00
Chuanhong Guo
028daa9974 ath79: ag71xx: apply interface mode to MII0/1_CTRL on ar71xx/ar913x
We currently don't have any code configuring interface mode in ath79,
meaning that we relies on bootloader to set the correct interface mode.

This patch added code to set interface correctly so that everything works
even if bootloader configures it wrong.(e.g. on WNDR3800 u-boot set
the second GMAC mode to RMII but it should be RGMII.)

Introduced "qca,mac-idx" for the difference in MII_CTRL register value.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-28 11:26:53 +02:00
John Crispin
9300eda00f ath79: replace patches
replace our downstream version of the patches with the ones
that were sent upstream.

Signed-off-by: John Crispin <john@phrozen.org>
2018-08-28 11:26:53 +02:00
Matt Merhar
d03c89838e ath79: initial support for Ubiquiti RouterStation and RouterStation Pro
This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other
.dts files that utilize it, ar7161_ubnt_routerstation.dts and
ar7161_ubnt_routerstation-pro.dts.

The modifications to generic-ubnt.mk, config-default, and base-files
necessary for image generation, parsing RedBoot FIS partitions, network
configuration, and sysupgrade are also included.

This reintroduces vital bits from platform_do_upgrade_combined() and its
supporting functions to /lib/upgrade/platform.sh, which were previously
removed from ath79 in 3e9d9f6225 "ath79:
sysupgrade: drop unused platform checks". The new function is called
"routerstation_do_upgrade" and will *only* work for the RouterStation
series of boards. It does however retain the ability to downgrade (e.g.
from master -> 17.01.x using sysupgrade -F).

All hardware is functional including the AR8216 switch (for the Pro),
wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button,
and LED.

Switch and LAN/WAN configuration is the same as it is with the
equivalent ar71xx targets. MAC addresses are assigned based upon the
content stored in the RedBoot config partition.

Flashing via both sysupgrade and TFTP has been confirmed to work. Also,
the initramfs images are now raw .bin files instead of being wrapped in
a uImage (as they currently are in ar71xx), which makes them bootable
with RedBoot.

One notable difference to ar71xx is the inclusion of the RedBoot
"fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in
DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD
parser’s DT binding, whose proper usage is mutually exclusive to
defining a separate fixed-partitions node for "RedBoot config". This
config partition contains the board's base MAC address. The lack of a
hard-coded flash location means that the mtd-mac-address property cannot
be used in the .dts, so instead fconfig is used to read the MAC
addresses from flash in userspace during first boot.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-08-27 19:31:17 +02:00
Paul Wassi
e348ccc4e6 treewide: fix some cosmetic glitches in dts files
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-08-27 19:31:17 +02:00
Felix Fietkau
d45b5a061d ath79: fix mac address increment for embedded wireless Dorin
Use mtd-mac-address-increment-byte to match ar71xx behavior

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-08-25 19:18:08 +02:00
Lech Perczak
4f3d700138 ath79: ubnt-xm: create mapping for RSSI LEDs
Ubiquiti XM series boards contain a set of RSSI LEDs. Create an UCI
mapping for them, so visual feedback on RSSI is available, when using
userspace RSSI monitor daemon.

Runtime tested using rssileds.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-08-23 22:42:15 +02:00
Lech Perczak
d40956a74c ath79: ubnt-xm: hijack LED4 as booting/failsafe
Create aliases for led-booting and led-failsafe pointing at
ubnt:green:link4 LED, forUbiquiti XM series, so visual feedback
on device status becomes available, in order to enter failsafe mode
via button. led-running and led-upgrade aliases are omitted to avoid
conflicting with RSSI LEDs when in normal operation.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-08-23 22:42:15 +02:00
Lech Perczak
7782715373 ath79: ubnt-xm: disable WAN on (rocket|bullet)-m
ubnt,bullet-m and ubnt,rocket-m targets support only single Ethernet
port, therefore disable creation of WAN zone and interfaces for them,
as their intended purpose is a wireless bridge. This aligns the
configuration with one found in ar71xx target.

ubnt,nano-m target is kept as is, being a two-port device.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-08-23 22:42:15 +02:00
Lech Perczak
614199c81d ath79: ubnt-xm: support ath9k firmware loading
Enable ath9k EEPROM extraction on boot for Ubiquiti XM-series boards.
This is required for wireless interface to function.
Runtime tested on Nanobridge M5.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2018-08-23 22:42:15 +02:00
INAGAKI Hiroshi
30b4f78193 ath79: add support for I-O DATA ETG3-R
I-O DATA ETG3-R is a wired router, based on Atheros AR9342.

Specification:

- Atheros AR9342
- 64 MB of RAM
- 8 MB of Flash
- 5x 10/100/1000 Ethernet
  - AR8327N
- 2x LEDs, 1x key
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using initramfs image:

1. Connect serial cable to UART header on ETG3-R
2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in
the TFTP directory
3. Set IP address of the computer to 192.168.0.10, connect to the
LAN port of ETG3-R, and start the TFTP server on the computer
4. Connect power cable to ETG3-R and turn on the router
5. Press "Enter" key when the "Hit any key to stop autoboot:" message
is displayed on the console and enter the u-boot cli
6. execute following commands to change kernel address for u-boot
  setenv bootsf 1
  setenv mtd_kernel1 "bootm 0x9f050000"
  saveenv
7. execute "tftpboot; bootm" command to download the initramfs image from
TFTP server and boot with it
8. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for ETG3-R
9. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-23 22:42:15 +02:00
David Bauer
98d3770379 ath79: fix TL-MR3020 image metadata
Sysupgrading to ath79 from ar71xx currently fails because of mismatching
supported_devices. ar71xx is expecting "tl-mr3020" which is missing in
the ath79 image. Upgrading from ath79 is unaffected, as the image
contains the old string for ar71xx and the new one coming from the
device-tree.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-19 18:58:04 +02:00
Chuanhong Guo
f195ab766c ath79: cleanup PISEN WMM003N image metadata
PISEN WMM003N is never supported by ar71xx, this commit also removed
SUPPORTED_DEVICES for it because it's completely useless.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-19 18:52:24 +02:00
David Bauer
3f8c5d5476 ath79: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.

SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM:   Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
USB:   1x USB 2.0
IN:    WPS button, WiFi button
OUT:   Power LED green, Internet LED green, WLAN LED green,
       LAN LED green, INFO LED green, INFO LED red
UART:  Header Next to Black metal shield
       Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
       The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (LAN + WAN)
 - WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

The USB port doesn't work. Both Root Hubs are detected as having 0 Ports:

[    3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.723267] usbcore: registered new interface driver usbfs
[    3.729058] usbcore: registered new interface driver hub
[    3.734616] usbcore: registered new device driver usb
[    3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.758357] SCSI subsystem initialized
[    3.766026] ehci-platform: EHCI generic platform driver
[    3.771548] ehci-platform ehci-platform.0: EHCI Host Controller
[    3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[    3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[    3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00
[    3.824001] hub 1-0:1.0: USB hub found
[    3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    3.835825] ehci-platform ehci-platform.1: EHCI Host Controller
[    3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[    3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[    3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00
[    3.894011] hub 2-0:1.0: USB hub found
[    3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    3.908928] usbcore: registered new interface driver usb-storage
[    3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/*

A few words about the shift-register:

AVM used a trick to control the shift-register for the LEDs with only 2
pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple
shift-registers, pulls the latch, moving the shift register-state to
the storage register. It also pulls down MR (normally pulled up) to
clear the storage register, so the latch gets released and will not be
pulled by the remaining bits in the shift-register. Shift register is
all-zero after this.

For that we need to make sure output 7 is set to high on driver probe.
We accomplish this by using gpio-hogging.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1).
Firmware can be uploaded like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-19 18:52:22 +02:00
Christian Lamparter
1c6e0f57a7 ath79: add support for TP-Link Archer C7 v1
TP-Link Archer C7 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

 - 720 MHz CPU
 - 128 MB of RAM (Various chips)
 - 8 MB of FLASH (Various chips)
 - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
 - minipcie slot with 3T3R 5 GHz QCA9880-AR1A (unsupported by ath10k!)
 - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
 - 10x LEDs, 2x software buttons

For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c7-1750>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-08-19 18:48:43 +02:00
INAGAKI Hiroshi
ff4bc483fc ath79: add support for I-O DATA WN-AC1167DGR
I-O DATA WN-AC1167DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- Qualcomm Atheros QCA9557
- 128 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz wifi
  - 2.4 GHz: SoC internal
  - 5 GHz: QCA988x
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1167DGR
2. Connect power cable to WN-AC1167DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-16 21:20:57 +02:00
Johann Neuhauser
94ee5e3d1d ath79: fix leds and network for TP-Link TL-WR841 v9/v11
Adding tl-wr841-v11 and the rename of tl-wr841n-v9 to tl-wr841-v9 in 01_leds
and 02_network script files are missing in commits cc35c91 and 8db6522.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[merged with identical case in 02_network]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
3f09adaa55 ath79: don't use the pcs,cr5000 wps led as usb led
If it isn't a usb led, it shouldn't be used as one by default. It is up
to the user to add such a (mis)configuration for the board.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Dmitry Tunin
0c5a532553 ath79: add support for TP-Link MR-3040 v2
Add support for the ar71xx supported TP-Link MR-3040 v2.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2018-08-16 21:20:57 +02:00
INAGAKI Hiroshi
9e6f22e309 ath79: add support for Buffalo WHR-G301N
Buffalo WHR-G301N is a 2.4 GHz 11n router, based on Atheros AR7240.
Ported from ar71xx target.

Specification:

- Atheros AR7240
- 32 MB of RAM
- 4 MB of Flash
- 2.4 GHz 2T2R wifi
- 5x 10/100 Mbps Ethernet
- 9x LEDs, 4x keys
  - LED: 8x gpio-leds, 1x ath9k-leds
  - key: 2x buttons, 1x slide switch
- UART header on PCB
  - Vcc, GND, TX, RX from LEDs side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WHR-G301N
2. Connect power cable to WHR-G301N and turn on it
3. Access to "http://192.168.11.1/" and open firmware update page
("ファーム更新")
4. Select the OpenWrt factory image and click execute ("実行") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[fix the SUPPORTED_DEVICES to be compatible with the ar71xx image]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
be06c726c4 treewide: drop unused get_status_led functions
The function isn't used for targets getting the status leds from the
devicetree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Mathias Kresin
dd448cd276 treewide: fix upgrade led handling
The upgrade led is only used if a running led is defined. If no running
led is defined, the upgrade led is ignored and upgrade isn't indicated
at all.

Instead, turn off the running led prior to turning the upgrade led on.
In most cases there isn't any visual change, but it allows to use an
independent led for upgrade indication.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
Dmitry Tunin
ae9c3105a3 ath79: use both WNDR3x00 power leds for boot status indication
Use the orange led by default to match the bootloader/stock firmware
behaviour. Turn on the green power led after boot to indicate a
finished boot and the orange one off.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message, keep orange power led enabled during early
kernel boot]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00
Dmitry Tunin
3d9610aa13 ath79: use both DIR-825 B1 power leds for boot status indication
Use the orange led by default to match the bootloader/stock firmware
behaviour. Turn on the blue power led after boot to indicate a finished
boot and the orange one off.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message, keep orange power led enabled during early
kernel boot]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00
Dmitry Tunin
7a873974f7 ath79: add support for indicating the boot state using multiple leds
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which
supports different leds for the different boot states.

The existing led sequences should be the same as before.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00
Chuanhong Guo
1213504750 ath79: add support for TP-Link TL-WR941N/ND v2/v3
Specification:
- SoC: Atheros AR9132
- Flash: 4 MB
- RAM: 32 MB
- Ethernet: Marvell 88E6060 with 5 FE ports.

Flash instruction:
  Upload the generated factory firmware on web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-14 10:19:37 +02:00
Johann Neuhauser
8db6522531 ath79: add support for TP-Link WR841N/ND v11
Specification:
- SoC: Atheros AR9533
- Flash: 4 MB
- RAM: 32 MB
- Ethernet: 4x LAN (100M) / 1x WAN (100M)
- WiFi: 2.4G 300M

Flash instruction:
  Flash factory image from stock WebUI.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-08-14 10:19:37 +02:00
Johann Neuhauser
18f738d3c4 ath79: move TP-Link WR841v9 aliases node from dtsi to dts
Move the alias node of the TP-Link WR841v9 and rename the phandle of
the qss led to qss_led in preparation for adding the very similar
TP-Link WR841v11.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-08-14 10:19:37 +02:00
Johann Neuhauser
cc35c91f56 ath79: fix sysupgrade TP-Link WR841v9
Remove SUPPORTED_DEVICES from wr841-v9 because it´s not needed and
for consistency rename everything to tl-wr841-v9.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-08-14 10:19:37 +02:00
Hannu Nyman
437e35f8a3 ath79: Add wifi to WNDR3700, WNDR3700v2 and WNDR3800
Add ath9k wifi capabilities to WNDR3700 family.

* use kmod-owl-loader to load firmware from "art"
* add wifi to DTS
* add wifi LEDs

Avoid using the same MAC for eth0 LAN and wlan0 by
toggling the eth0 MAC into a locally administered MAC.
That is currently done by in user-space by adding a
uci config item into /etc/config/network
(More elegant solution might be setting it already in
preinit phase.)

Known issues:

* wifi firmware file may not get created on the first boot
  after flashing on time to bring wifi normally up. Likely
  the overlay jffs2 is not yet ready for creating the
  firmware file. "wifi up" may still bring wifi up.
  Wifi will work normally at subsequent boots.

* phy0 and phy1 may get assigned mixed, so that phy0 may
  be the 5GHz radio instead of the normal 2.4GHz, and vice
  versa for phy1. Does not happen always, but may happen.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[fix the wifi unit address in the dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-14 10:19:37 +02:00
Icenowy Zheng
b2a33d5463 ath79: add support for Pisen WMM003N (Cloud Easy Power)
Pisen WMM003N (sold under the name of Cloud Easy Power) is an
AR9331-based router and power bank combo device. The device uses a
stock firmware modified from OpenWRT for TP-Link TL-WR703N; however
some GPIO definition is different on this device with TL-WR703N. An
AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also
added, and the stock Flash/RAM configuration is 8MiB/64MiB.

The stock firmware is an old and heavily modified OpenWRT-based
firmware, which has telnetd defaultly open, and the root password is
"ifconfig" (quotation marks not included). The factory image format is
not known yet, however the stock firmware ships the OpenWRT's sysupgrade
command, and it can be used to install a newer firmware.

Due to the lack of the access to the STM8 embedded controller, the SD
slot is currently not usable (because it's muxed with the on-board USB
port) and the AXP PMIC cannot be monitored.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
2018-08-14 10:19:37 +02:00
Peter Lundkvist
3337f202d6 ath79: drop tl prefix for TP-Link RE450 v2
This router is called RE450 and the tl prefix was used to identify it
as a TP-Link device. Drop the tl prefix since we now have tplink in
dts and device name.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
2018-08-13 08:51:31 +02:00
Christian Lamparter
f3ffac90bc ath79: gmac: add parsers for rxd(v)- and tx(d|en)-delay for AR9344
Some AR9344 boards do very poorly with the default settings and
need custom rxdv-delay, rxd-delay, txd-delay, txen-delay flags
to perform reasonably.

In this case the WD My Net Wi-Fi Range Extender can not even
manage 10Mbps on a 1Gbit link:

root@AR9344:~# iperf3 -s
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from client [...]
[  5] local [...] connected to client
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  1.09 MBytes  9.16 Mbits/sec
[  5]   1.00-2.00   sec   895 KBytes  7.33 Mbits/sec
[  5]   2.00-3.00   sec   762 KBytes  6.25 Mbits/sec
[...]
[  5]  10.00-10.03  sec  17.0 KBytes  4.74 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.03  sec  9.00 MBytes  7.52 Mbits/sec

with but with the correct settings in place, it does much better:

root@AR9344:~# iperf3 -s
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from client [...]
[  5] local [...] connected to client
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  23.1 MBytes   193 Mbits/sec
[  5]   1.00-2.00   sec  23.1 MBytes   194 Mbits/sec
[  5]   2.00-3.00   sec  23.2 MBytes   195 Mbits/sec
[...]
[  5]  10.00-10.04  sec   710 KBytes   180 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.04  sec   237 MBytes   198 Mbits/sec

The tx data and enable delay bits definitions are taken from Atheros'
AR9344 Data Sheet Section "8.6.1 Ethernet Configuration (ETH_CFG)" on
page 153.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-08-13 08:48:37 +02:00
David Bauer
7d1b742b4d ath79: add QCA956x GMAC config
This commit adds the ability to configure the GMAC of the QCA956x.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-13 08:43:15 +02:00
Chuanhong Guo
cf50f72069 ath79: ar913x: fix eth pll register
PLL for eth0 internal clock on ar913x is at 0x18050014
and AR913X_ETH0_PLL_SHIFT is 20 instead of 17

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-13 08:37:19 +02:00
Chuanhong Guo
42b3fdf981 ath79: ag71xx: fix speed applied to MII0/1_CTRL on ar71xx/ar913x
Currently speed value is applied to interface mode field.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-13 08:37:19 +02:00
Hannu Nyman
4dc7cb792a ath79: add WNDR3700 and WNDR3700v2
Add support for WNDR3700 and WNDR3700v2.

They share most things with WNDR3800.
Only device IDs and partition structure needs to be set.

Note: WNDR3700 (v1) has no NETGEAR_HW_ID, but has
      also the NA version of the factory image.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-08-13 08:37:19 +02:00
Hannu Nyman
b58df9919e ath79: create WNDR3700 series .dtsi and adjust WNDR3800
Prepare for addition of WNDR3700 and WNDR3700v2 by
separating the common parts into wndr3700.dtsi and
leaving just the device-specific things into wndr3800.dts

The three routers are identical except
  * device IDs
  * WNDR3700 (v1) has only 8 MB flash, while others have 16 MB.
    Partition structure needs to be defined for each device.
  * (WNDR3800 has 128 MB RAM, but RAM size is not in DTS)

Also separate the common parts of the image recipe.
(Drop also the initramfs recipe.)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-08-13 08:37:19 +02:00
Chuanhong Guo
8e4e545ecb ath79: fix eth pll for ar913x
PLL node is missing syscon in compatible string.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-11 21:46:18 +02:00
INAGAKI Hiroshi
a6369206fe ath79: add support for I-O DATA WN-AC1600DGR2
I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- Qualcomm Atheros QCA9557
- 128 MB of RAM
- 16 MB of Flash
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 3T3R (QCA9880)
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR2
2. Connect power cable to WN-AC1600DGR2 and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-11 21:45:06 +02:00
Dmitry Tunin
97de133368 ath79: add support of D-Link DIR-825 B1
Add support for the ar71xx supported D-Link DIR-825 B1 to ath79.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2018-08-11 21:45:04 +02:00
Christian Lamparter
a441c86d93 ath79: add ath9k calibration data MAC addresses patching
This patch copies over the MAC patching helper functions from lantiq's
target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
file.

Not all vendors bothered to write the correct MAC addresses for the
ath9k wifi into the calibration data. And while ath9k does have some
special dt-properties to extract the addresses from a fixed position,
there are still devices that require userspace to edit or modify
the caldata.

In my case, the MAC address for the Wi-Fi device is stored in an
unsorted key-value based "nvram" database and there's an existing
userspace tool to extract the data.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-08-11 21:36:27 +02:00
Chuanhong Guo
d4e3a31f6c ath79: add support for TP-Link TL-WDR4900 v2
Specification:
- SoC: Qualcomm Atheros QCA9558
- Flash: 8 MB
- RAM: 128 MB
- Ethernet: AR8327N with 5 GE ports.
- Wireless radio: QCA9558 for 2.4G and AR9580 for 5G.

Flash instruction:
  Upload the generated factory firmware on web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-11 21:36:27 +02:00
David Bauer
c4931713df ath79: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-09 18:44:57 +02:00
Chuanhong Guo
387736af41 ath79: ag71xx: remove PHY reset
Bit 8/12 of reset controller which is marked as PHY_RESET/SWITCH_RESET
in datasheets will trigger either a reset for builtin switch or assert
an external ETH0_RESET_L/ETH1_RESET_L pin, which are usually connected
to external PHY/switch. None of them should be triggered every time an
interface is brought up in ethernet driver.

Remove PHY reset support from ag71xx and definition for them in dtsi.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-09 18:44:57 +02:00
INAGAKI Hiroshi
23519edbca ath79: add support for Buffalo BHR-4GRV2
Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros
QCA9558.
Ported from ar71xx target.

Specification:

- Qualcomm Atheros QCA9558
- 64 MB of RAM
- 16 MB of Flash
- 5x 10/100/1000 Ethernet
  - QCA8337N
- 4x LEDs, 2x keys
- UART header on PCB
  - Vcc, TX, RX, GND from LED side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of BHR-4GRV2
2. Connect power cable to BHR-4GRV2 and turn on it
3. Access to "http://192.168.12.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新実行")
button
5. Wait ~120 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-09 18:44:57 +02:00
David Bauer
6555612783 ath79: fix PLL settings for QCA955x
This adds PLL settings for the ethernet ports of the TP-Link TL-WR1043
v2/v3 and the Openmesh OM5P-AC-v2.

We also change the PLL-settings in the qca9557.dtsi to match the ones
used as default on the ar71xx target.

As of 4b9680f138 those devices have broken ethernet ports as the default
PLL settings defined in the QCA9557.dtsi are applied which are off for
those devices.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-09 17:24:39 +01:00
Kevin Darbyshire-Bryant
995a1ba841 ath79: add pll for archer c7
commit 4b9680f fixed pll settings and the correct pll set
by bootloader is overrided by value in qca9557.dtsi which
is incorrect for Archer C7 and breaks ethernet. Add pll
values for archer c7 to fix ethernet connection.

This individual pll tweak has been cherry picked from github pr 1260
which changes a couple of things in a single commit and should be
ideally split.  This commit get archer v7 back and working.

Tested: archer c7 v2

Original combined commit authored by:
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
c7 fix only split out by:
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-08-09 17:04:59 +01:00
David Bauer
4b9680f138 ath79: fix QCA9557 eth PLL settings
The QCA9557 dtsi is currently missing pll-handle and pll-regs for both
eth0 and eth1, therefore PLL settings won't be applied. This commit
fixes this behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-08 08:38:45 +02:00
Mathias Kresin
b94b4b0862 ath79: don't include tl-wdr3600 image build code for tl-wdr4300
Including the tl-wdr3600 image build code just to overwrite most of it
doesn't make much sense and only makes it hard to read.

Furthermore, the tl-wdr4300 image will be marked as compatible with the
tl-wdr3600 this way.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
Mathias Kresin
12121e643b ath79: cleanup netgear wnr612-v2 supported devices
The netgear,wnr612-v2 is included by default based on the device
define.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
Mathias Kresin
38877d8873 ath79: mark netgear variables as device specific
The variables are used in image build recipes and need to be marked as
per devices vars to be stored individual per image define. Otherwise
the last defined variable will be used for all boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
Chuanhong Guo
1edba538a9 ath79: Fix led nodes for TL-WR740N v2 and add its clones
This patch did the following things:
1. Separate ath9k-leds out of gpio leds so that all other leds will work
   before ath9k loded (e.g. during preinit/init stage).
2. Rename wps led to qss since that's how TP-Link mark it.
3. Rename LED prefix to tp-link because that dts is shared by many devices.
4. Rename to wr740n-v1 because v1 is the first and v2 just use the fw of v1.
   (This will require a forced sysupgrade if you comes from
   the previous wr740n v2 image.)
5. Remove SUPPORTED_DEVICES.
   (tl-wr740n-v2 doesn't exist anywhere so it's useless.)
6. Add all WR741ND v1 clones found in ar71xx.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-08 08:11:11 +02:00
Mathias Kresin
55ff2951ea ath79: fix dts warnings
Fix all issues found by the devicetree compiler like wrong address/size
cells as well as wrong/missing/superfluous unit addresses.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 08:11:11 +02:00
Mathias Kresin
bf078fcab6 ath79: fix node names
Use the standardized node names from the devicetree specification.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:22 +02:00
Mathias Kresin
a8ad7b6efa ath79: fix compatible strings
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:22 +02:00
Mathias Kresin
7b42247182 ath79: fix whitespace issue in dts files
Fixes spaces vs. tabs issues and remove indentation on blank lines.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:22 +02:00
Chuanhong Guo
18a2595315 ath79: rename tl-archer-c7 to archer-c7
This router is called Archer C7 and the tl was used to identify
TP-LINK. Since we have added tplink in dts/board name, the tl
prefix is useless now.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
2d5fee248c ath79: alphabetical order image/generic.mk
Move the wzr-hp-g450h in image/generic.mk to keep alphabetical order.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
8288af1e18 ath79: rename dts/image using manufacturer_board scheme
This helps getting rid of SUPPORTED_DEVICES which can be
auto-generated in image/Makefile.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
2da431e583 ath79: remove quotes for boardname in scripts
Quotes are not required in case statements.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
f9065e44a6 ath79: put all devices in alphabetical order in scripts
And remove specifying lan interfaces as eth1.1 because this is
handled by ucidef_add_switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
3804134369 ath79: fix support for TL-MR3020 v1
Change lan and it's LED to eth0
It's broken since c7c807cb8c
where I changed the dts but forgot to change default configurations.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
690c55e8cc ath79: fix support for TL-WR740N/WR741N v4
1. Swap eth0/eth1
 Both devices are using AR9331, the builtin switch on AR9331 is
 connected to gmac1 and gmac1 is named as eth1 in ath79.
 PS: gmac1 is eth0 and gmac0 is eth1 in ar71xx because of the
 reversed initialization order.
2. Fix the incorrect compatible string in dts

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
Chuanhong Guo
115e993adc ath79: remove useless phy-handle nodes
phy-handle is used to poll link status. They are useless when
we need fixed-link on these interfaces.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-06 07:31:54 +02:00
René van Dorst
0ae9396556 treewide: convert gpio-export to platform driver
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.

gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.

Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
1d18a14a90 ath79: really fix TP-Link Archer C7 v2 MAC address
Revert 290c54473e ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address")
which obviously aims to have a distinct MAC address per interface.

Unfortunally it doesn't match what is used by the stock firmware and we
shouldn'z use MAC Adresses not reserverd for/assigned to a particular
board.

The correct MAC adress increments for this board are:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

Fixes: FS#408

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Koen Vandeputte
f960490fc8 kernel: bump 4.14 to 4.14.60
Refreshed all patches

Removed upstreamed patches:
- 500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-03 16:10:38 +02:00
Daniel F. Dickinson
60cf71ede7 ath79: Forward port support for CR3000
The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct
NaaS offering.  It was previously supported under the ar71xx branch and
this forward ports that support with some notable differences:

1) Since reverting to stock firmware is now irrelevant there is is only
a single openwrt image generated which uses the entire flash rather than
preserving PowerCloud-specific partitions that are unneeded to openwrt--
those partitions will be erased and used by the openwrt image.

2) Rather than use a non-standard probe order for the ethernet devices,
this image uses a set of 'ip link set ethX name ethY' commands very early
in preinit (before the network is used at all), in order to have the the
switch and Wan use the same ethernet names as in previous images.

3) /etc/config/wireless will need to be regenerated as the path to the
wireless device has changed due to differences in ath79 DT for ar93x
compared to ar71xx images.

4) eth0 is wan and eth1 is lan (switch)

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:53 +02:00
Stijn Tintel
22b9f99b87 kernel: bump 4.14 to 4.14.59
Drop patch that was superseded upstream:
ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch

Drop upstreamed patches:
- apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch
- apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch
- ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch
- generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch
- generic/pending/900-gen_stats-fix-netlink-stats-padding.patch

In 4.14.55, a patch was introduced that breaks ext4 images in some
cases. The newly introduced patch
backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
addresses this breakage.

Fixes the following CVEs:
- CVE-2018-10876
- CVE-2018-10877
- CVE-2018-10879
- CVE-2018-10880
- CVE-2018-10881
- CVE-2018-10882
- CVE-2018-10883

Compile-tested: ath79, octeon, x86/64
Runtime-tested: ath79, octeon, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 05:11:07 +03:00
Matt Merhar
af3b1756f0 ath79: fix irq assignment for pci-ar71xx driver
In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being
called before populating the PCI controller's device_node struct member.
This led to no IRQ being assigned to connected PCI devices (e.g. ath9k
cards) and caused them to be non-functional aside from simply being
detected.

The previous errors encountered in dmesg were: "irq: no irq domain found
for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ
of 0 for the cards.

While this has been only been tested on a yet-to-be-merged RouterStation
Pro target, it should also fix the broken wifi people have reported for
the ath79 WNDR3800 target.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-07-30 20:22:44 +02:00
Lucian Cristian
accb67e582 ath79: add support for tl-wr841n-v9
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 16:14:49 +02:00
Chuanhong Guo
7a07b4cff0 ath79: Add switch reset definition in dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
f593020a28 ath79: ag71xx: assert a switch reset if defined in dts.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
a5fa6b3825 ath79: ar724x: Fix reset definition for gmac0/gmac1
reset bit 8 is for builtin switch and bit 12 is marked 'reserved' on datasheet.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
4e5ba50760 ath79: ar7240: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
f43e8f9004 ath79: ag71xx: Explicitly register mdio bus after ag71xx_hw_init() for ar7240
mdio bus isn't a standalone device on ar7240. (and maybe older SoCs?)
Use simple-mfd for ar7241 and later SoCs to get mdio1 ready before gmac0
For ar7240 and older chips, manually create platform device after
ag71xx_hw_init() in ag71xx_probe()to get mdio0 ready between
ag71xx_hw_init() and ag71xx_phy_connect().

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo
85189e4c00 ath79: ag71xx: Rework mdio clock settings
Allow specifying desired mdio clock frequency in dts.
Use default frequency around 5MHz for builtin switch and 2MHz for other mdio bus.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
bb7fac4369 ath79: ar7242: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
113b4cf90f ath79: ar7241: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
b6c8e5deae ath79: Fix support for TP-LINK Archer C7 v2
Remove mdio1 and phy1 handle. AR8327N is controlled through mdio0.
Add gmac-config for Archer C7.
Remove ucidef_set_interfaces_lan_wan. They can be determined by config_generate automatically.

The following are for adding support for WDR4900 v2/Archer C7 v1 and other
devices that shared the same machine file in ar71xx:
Move mtd partitions to archer-c7-v2.dts. Only Archer C7 v2 has 16M flash.
Flash on Archer C7 v1/TL-WDR4900 v2 is 8M.
Add label for wlan leds. The default trigger for archer c7/wdr4900 is different.
Move wlan5g led to archer-c7-v2.dts. 5G led on WDR4900 is connected to ar9380.
Move rfkill definition to archer-c7-v2.dts. There is no such a button on wdr4900 v2.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
18db385eb7 ath79: qca955x: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
b7a10772d1 ath79: qca956x: Update dts for current ag71xx driver
enable mdio1 by default because mdio1 node is a subnode of eth1
and eth1 node is a "simple-mfd", which makes mdio1 disabled when
eth1 isn't enabled.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
fc1f55ebf4 ath79: qca953x: Add chosen node and specify console in bootargs
Most qca devices use 115200n8 as it's default uart baudrate.
Add 'chosen' node for qca953x like other SoCs in ath79 target.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
e8245c5b3f ath79: qca953x: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Lucian Cristian
e6417390e0 ath79: update qca9533 to new irq driver
Commit c7efc93 renamed controller name
to qca,ar9340-intc and added some functions but qca9533.dtsi was overlooked.
Correct the dtsi and adust it to the new format

Add gmac and correct reset for cascaded irq and build-in switch
Also add the reference clock to soc dtsi so we don't have to have it in every dts

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>

Remove switch reset definition
Fix gmac compatible string (We only need SW_PHY_SWAP and SW_PHY_ADDR_SWAP on qca953x so use ar9330-gmac instead of ar9340-gmac.)

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo
c7c807cb8c ath79: ar933x: Update dts for current ag71xx driver
gmac0 is always connected to switch phy4 and mdio1 is always needed.
So add phy handle for eth0 and enable mdio1 by default.
Move fixed-link for gmac1 from device dts to ar9331.dtsi because gmac1 is always connected to builtin switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
f6c99241ba ath79: ar934x: Update dts for current ag71xx driver
Enable mdio1 by default because mdio1 is needed when eth1 is enabled.

PS: If a ar9341 device has only one port and you only want to use gmac0,
change compatible of gmac1 to "syscon", "simple-mfd" in dts.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
7ae9e63719 ath79: ag71xx: Make builtin switch driver a separated module
This patch did several things:
1. Probe the builtin switch as a separated mdio device.
2. Register a separated mdio bus for builtin switch.
3. Use generic mdio read/write function instead of calling ag71xx_mdio_mii_read/write directly.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
83d2dbc599 ath79: ag71xx: Split mdio driver into an independent platform device.
We need to have mdio1 belonging to gmac1 initialized before gmac0.
Split it into a separated mdio device to get both mdios ready before probing gmac.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
24cbe27bb7 ath79: ag71xx: Remove ar7240_set_addr and ag71xx_ar7240_start
The builtin switch has it's initial valid mac address(00:00:01:00:00:00).
Since the builtin switch is an independent device, setting mac address of gmac1 to builtin switch isn't a good idea and this makes it impossilbe to split builtin switch apart as an independent platform device.
Remove these functions and apply default VLAN during initialization as a preparation for further driver splitting.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
2d081addb5 ath79: ag71xx: Split gmac config into separated file and add support for ar934x/qca955x.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo
b346c37588 ath79: Fix mac reset and gmac compatible in ar934x.dtsi
Also add phy-mode and fixed-link as gmac1 is always connected
to the builtin switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Daniel F. Dickinson
915966d861 ath79: Port PowerCloud Systems CAP324 support
The CAP324 was an AP for a NaaS offering that is now defunct.  While
previously supported in the ar71xx arch, there were some errata (to
be fixed shortly).

Notable differences from ar71xx support:

1) The method of getting the ath9k firmware for the PCIe 2ghz wifi has
changed (due to changes in how the arch handles this), since this device
doesn't use the EEPROM except to get the MAC address of the wifi.

2) /etc/config/wireless will need to be regenerated as the path(s) to
the wireless device(s) have changed.

3) ath79 OpenWrt firmware no longer supports build an image that allows
reverting to stock firmware (as the cloud service no longer exists, the
stock firmware is useless), instead using all of the flash for image and
overlay (less u-boot/env and art).

4) Initial network config treats the ethernet port as a Lan port with
the standard default address (192.168.1.1 unless changed in .config
--e.g. via menuconfig) instead of using DHCP (this was the default for
the stock firmware, however for openwrt use this is rather confusion and
counter-productive as the user has a harder time finding the device on
the network.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:31 +02:00
Daniel F. Dickinson
4b93cbd172 ath79: Port PowerCloud Systems CR5000 support
Add ath79 arch support for PowerCloud Systems CR5000.  Previously
supported under ar71xx (however there are some errors in that support;
to be fixed shortly).

Info:

* This board is based on the Atheros DB120 reference design, but doesn't
  use the on-board switch.  Instead it attachs GMAC0 to an AR8327 switch.
* It only uses GMAC0 and the WAN is simply a VLAN in the stock firmware.
* It has 64MB RAM and 8MB flash.
* In the dts version we get rid of using 'open-drain' for the AR8327
  LED controls.
* As with the platform data version we disable JTAG as this conflicts
  with one of the pair of GPIO's required for the power/status LED
  (GPIO2 and GPIO4 are used for this LED).
* The pcie card wifi has an EEPROM but gets it's MAC address from
  the ART partition.
* The SoC wifi (2.4 GHz) is all from the ART.
* The USB is support comes from the SoC.

NB. This is actually an AR9342 rather than AR9344 but we use the 9344
definitions because there are no relevant differences for this board.

NB: Building only images that don't support reverting to the old
cloud-based firmware as the Skydog cloud service for the CR5000 no
longer exists.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:31 +02:00
David Bauer
5409dcffbd ath79: fix OCEDO Raccoon
The OCEDO Raccoon only has one ethernet port, but currently uci sections
for WAN and LAN are created.

Additionally, newer versions of the devices U-Boot (units with SteelWRT)
set the kernel-cmdline and therefore overwrite the partition-layout.
We fix this by overwriting the cmdline supplied by the bootloader.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-07-25 08:59:33 +02:00
Aleksandr V. Piskunov
290c54473e ath79: fix TP-Link Archer C7 v2 wlan1 MAC address
The mac address for the 2.4 wireless need to be decremented by one.

Correct MAC adress increments for this board are:
wlan0 (5GHz)   : -2
wlan1 (2.4GHz) : -1
eth1  (LAN)    :  0
eth0  (WAN)    :  1

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
2018-07-18 19:17:46 +02:00
Mathias Kresin
cf7154db07 kernel: only optimized for size if small_flash
Add a new config option to allow to select the default compile
optimization level for the kernel.

Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.

Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.

Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.

Exceptions to the above are:

  - lantiq, where the optimization for size is only required for the
    xway_legacy subtarget but was set for the whole target
  - mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
    plenty of space and an optimization for size doesn't make much sense
  - rb532, which has 128MByte flash

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:15:32 +02:00
David Bauer
6476148034 ath79: add support for OCEDO Raccoon
This commit adds support for the OCEDO Raccoon

SOC:	Atheros AR9344
RAM:    128MB
FLASH:  16MiB
WLAN1:  AR9344 2.4 GHz 802.11bgn 2x2
WLAN2:  AR9382 5 GHz 802.11an 2x2
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

	NOTE: The U-Boot won't boot with the serial attached.
	Boot the device without serial attached and attach it
	after 3 seconds.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'raccoon-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-07-08 00:04:27 +02:00
Lucian Cristian
2d268c0710 ath79: disable unused drivers for tiny target
Shrink the tiny kernel by moving all switch and ethernet phy drivers to
the generic kernel config instead of the target kernel config.

All boards in the tiny and nand target are either ar7240 or ar9331 based,
which don't support external xMII and therefore no external ethernet phy
can be connected. None of the boards uses a realtek switch either.

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-07 21:07:40 +02:00
Lucian Cristian
80e3a16fda ath79: optimize ath79 tiny target for size
the speed impact on tiny target is minimal and worth the size gained

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-07 21:07:40 +02:00
Christoph Krapp
e420b7b5c5 ath79: add support for UniFi AC-Mesh Pro
The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-07 21:07:40 +02:00
Christoph Krapp
8722c52b41 ath79: remove bs-partition ro-flag for UniFi AC devices
This removes the read-only flag from the bs (bootselect) partition
on UniFi AC devices. This allows to correct the indicator from which
partition the device is booting its kernel from.

See also:
 - freifunk-gluon/gluon#1301
 - https://bugs.lede-project.org/index.php?do=details&task_id=662

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-04 01:20:03 +02:00
Aleksandr V. Piskunov
63c9081c77 ath79: swap TP-Link Archer C7 v2 USB port LED and GPIO names
TP-Link Archer C7 v2 USB port LED and GPIO names are in incorrect order,
i.e. in order to match actual user visible labels, usb1 should be usb2,
and vice versa.
This patch swaps LED and GPIO power control node names.

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
2018-07-04 01:20:03 +02:00
Mathias Kresin
31aa62c5ec ath79: drop mv88e6063 switch driver
Due do a missing KCONFIG isn't selectable nor enabled in the target
kernel config. Drop it for now and enable/add the driver at the time it
is required.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-04 01:20:02 +02:00
Peter Lundkvist
781ad46206 ath79: add support for TP-Link RE450 v2
TP-Link RE450 v2 is a dual band router/range-extender
based on Qualcomm/Atheros QCA9563 + QCA9880.

Specification:

- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button
- UART header on PCB (needs unmounted R64 & R69 0201 resistors/jumpers)

Flash instruction:
Apply factory image in OEM firmware web-gui.

U-Boot does not seem to have any recovery functions, so
debricking requires connection via UART.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
2018-07-02 07:05:33 +02:00
Rocco Folino
4ff019722c ath79: port TP-Link TL-WR741ND v4 and TL-WR740ND v4
This patch ports the TP-Link TL-WR741ND v4 and TL-WR740ND v4 to the
ath79 target.

Because the two devices share the same hw layout, this patch adds a common
.dtsi which is included by the two .dts.

Signed-off-by: Rocco Folino <rocco@folino.io>
2018-07-02 07:03:21 +02:00
Rocco Folino
9b575288eb ath79: add pinmux to ar9330
This patch adds the pinmux support to the ar9330 used to disable the
JTAG or to enable switch LEDs

Signed-off-by: Rocco Folino <rocco@folino.io>
2018-07-02 07:00:20 +02:00
Adrian Schmutzler
4456dd4660 ath79: add support for Unifi AC Mesh
The Unifi AC Mesh is equivalent to the Unifi AC Lite. However,
for setting certain parameters with the flashed device it is
helpful that the devices know their variant (e.g. automatically
setting antenna gain for the different antennas in Lite and Mesh).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-28 20:31:48 +02:00