mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-18 21:28:02 +00:00
ath79: add support for I-O DATA WN-AC1600DGR2
I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM - 16 MB of Flash - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR2 2. Connect power cable to WN-AC1600DGR2 and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi
Mathias Kresin
parent
97de133368
commit
a6369206fe
@ -264,6 +264,11 @@ define Build/openmesh-image
|
||||
"$(call param_get_default,rootfs,$(1),$@)" "rootfs"
|
||||
endef
|
||||
|
||||
define Build/senao-header
|
||||
$(STAGING_DIR_HOST)/bin/mksenaofw $(1) -e $@ -o $@.new
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/sysupgrade-tar
|
||||
sh $(TOPDIR)/scripts/sysupgrade-tar.sh \
|
||||
--board $(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)) \
|
||||
|
||||
@ -46,6 +46,11 @@ ath79_setup_interfaces()
|
||||
glinet,ar300m)
|
||||
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
||||
;;
|
||||
iodata,wn-ac1600dgr2|\
|
||||
pcs,cr5000)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
||||
;;
|
||||
netgear,wndr3800)
|
||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
@ -66,10 +71,6 @@ ath79_setup_interfaces()
|
||||
"0@eth1" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
|
||||
ucidef_set_interface_wan "eth0"
|
||||
;;
|
||||
pcs,cr5000)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
||||
;;
|
||||
phicomm,k2t)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
|
||||
@ -152,6 +153,10 @@ ath79_setup_macs()
|
||||
lan_mac=$(mtd_get_mac_text "caldata" 65440)
|
||||
wan_mac=$(mtd_get_mac_text "caldata" 65460)
|
||||
;;
|
||||
iodata,wn-ac1600dgr2)
|
||||
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
||||
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
||||
;;
|
||||
phicomm,k2t)
|
||||
lan_mac=$(k2t_get_mac "lan_mac")
|
||||
wan_mac=$(k2t_get_mac "wan_mac")
|
||||
|
||||
@ -95,6 +95,17 @@ ath9k_patch_fw_mac_crc() {
|
||||
board=$(board_name)
|
||||
|
||||
case "$FIRMWARE" in
|
||||
"ath9k-eeprom-ahb-18100000.wmac.bin")
|
||||
case $board in
|
||||
iodata,wn-ac1600dgr2)
|
||||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
|
||||
;;
|
||||
*)
|
||||
ath9k_eeprom_die "board $board is not supported yet"
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
"ath9k-eeprom-pci-0000:00:00.0.bin")
|
||||
case $board in
|
||||
avm,fritz300e)
|
||||
|
||||
@ -87,6 +87,10 @@ board=$(board_name)
|
||||
case "$FIRMWARE" in
|
||||
"ath10k/cal-pci-0000:00:00.0.bin")
|
||||
case $board in
|
||||
iodata,wn-ac1600dgr2)
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
||||
;;
|
||||
ocedo,koala)
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
|
||||
|
||||
216
target/linux/ath79/dts/qca9557_iodata_wn-ac1600dgr2.dts
Normal file
216
target/linux/ath79/dts/qca9557_iodata_wn-ac1600dgr2.dts
Normal file
@ -0,0 +1,216 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca9557.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "iodata,wn-ac1600dgr2", "qca,qca9557";
|
||||
model = "I-O DATA WN-AC1600DGR2";
|
||||
|
||||
aliases {
|
||||
led-status = &power;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power: power {
|
||||
label = "wn-ac1600dgr2:green:power";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
copy {
|
||||
label = "wn-ac1600dgr2:green:copy";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
eco {
|
||||
label = "wn-ac1600dgr2:green:eco";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "wn-ac1600dgr2:green:wlan5g";
|
||||
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "wn-ac1600dgr2:green:wlan2g";
|
||||
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
notification {
|
||||
label = "wn-ac1600dgr2:amber:notification";
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
button_eco {
|
||||
label = "eco";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
auto {
|
||||
label = "auto";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
button_copy {
|
||||
label = "copy";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
router {
|
||||
label = "router";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x030000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "firmware";
|
||||
reg = <0x040000 0xe50000>;
|
||||
};
|
||||
|
||||
partition@e90000 {
|
||||
label = "manufacture";
|
||||
reg = <0xe90000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f90000 {
|
||||
label = "backup";
|
||||
reg = <0xf90000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fa0000 {
|
||||
label = "storage";
|
||||
reg = <0xfa0000 0x050000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x87600000 /* PORT0 PAD MODE CTRL */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x56000000 0x00000101 0x00001616>;
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "pci168c,003c";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
qca,no-eeprom;
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
@ -67,6 +67,18 @@ define Device/glinet_ar300m_nor
|
||||
endef
|
||||
TARGET_DEVICES += glinet_ar300m_nor
|
||||
|
||||
define Device/iodata_wn-ac1600dgr2
|
||||
ATH_SOC := qca9557
|
||||
DEVICE_TITLE := I-O DATA WN-AC1600DGR2
|
||||
IMAGE_SIZE := 14656k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
||||
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
||||
senao-header -r 0x30a -p 0x60 -t 2 -v 200
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k ath10k-firmware-qca988x
|
||||
endef
|
||||
TARGET_DEVICES += iodata_wn-ac1600dgr2
|
||||
|
||||
define Device/ocedo_koala
|
||||
ATH_SOC := qca9558
|
||||
DEVICE_TITLE := OCEDO Koala
|
||||
|
||||
@ -108,11 +108,6 @@ define Build/poray-header
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/senao-header
|
||||
$(STAGING_DIR_HOST)/bin/mksenaofw $(1) -e $@ -o $@.new
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/seama
|
||||
$(STAGING_DIR_HOST)/bin/seama -i $@ $(1)
|
||||
mv $@.seama $@
|
||||
|
||||
Loading…
Reference in New Issue
Block a user