mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 05:38:00 +00:00
ath79: add support for ROSINSON WR818 board
This commit adds support for the ROSINSON WR818 WiFi-Router
SoC: Qualcomm Atheros QCA9563,
FLASH: Winbond W25Q128FV 16MBytes,
WiFi: QCA9563 b/g/n 3x3 450Mbit/s,
USB: 1x USB 2.0 Type A, 1x USB2.0 Type C,
IN: WPS/Reset button GPIO1,
OUT: Power LED red, Internet LED red, WLAN LED red,
LAN1 LED red, LAN2 LED red, System LED red,
UART: RX-GPIO18, TX-GPIO22,
Tested and working:
- Ethernet (LAN + WAN)
- WiFi
- OpenWRT sysupgrade
- Button
- LEDs
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.1.1
- Go to "Administration" -> "Firmware Upgrade"
- Upload the OpenWrt sysupgrade image
Signed-off-by: Rosy Song <rosysong@rosinson.com>
This commit is contained in:
Rosy Song
Mathias Kresin
parent
7574781337
commit
31469aebd4
@ -111,6 +111,10 @@ ath79_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
|
||||
;;
|
||||
rosinson,wr818)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan" "2:lan" "3:wan"
|
||||
;;
|
||||
tplink,archer-c7-v1|\
|
||||
tplink,archer-c7-v2|\
|
||||
tplink,tl-wdr4900-v2)
|
||||
@ -230,6 +234,10 @@ ath79_setup_macs()
|
||||
lan_mac=$(k2t_get_mac "lan_mac")
|
||||
wan_mac=$(k2t_get_mac "wan_mac")
|
||||
;;
|
||||
rosinson,wr818)
|
||||
wan_mac=$(mtd_get_mac_binary factory 0)
|
||||
lan_mac=$(macaddr_setbit_la "$wan_mac")
|
||||
;;
|
||||
tplink,tl-wr1043nd-v4)
|
||||
base_mac=$(mtd_get_mac_binary product-info 8)
|
||||
wan_mac=$(macaddr_add "$base_mac" 1)
|
||||
|
||||
162
target/linux/ath79/dts/qca9563_rosinson_wr818.dts
Normal file
162
target/linux/ath79/dts/qca9563_rosinson_wr818.dts
Normal file
@ -0,0 +1,162 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
/ {
|
||||
model = "ROSINSON WR818";
|
||||
compatible = "rosinson,wr818", "qca,qca9560";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &system;
|
||||
led-failsafe = &system;
|
||||
led-running = &system;
|
||||
led-upgrade = &system;
|
||||
};
|
||||
|
||||
gpio_leds: leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
system: system {
|
||||
label = "wr818:red:system";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi_2g {
|
||||
label = "wr818:red:wifi2g";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
num-cs = <1>;
|
||||
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "firmware";
|
||||
reg = <0x050000 0xf80000>;
|
||||
};
|
||||
|
||||
info: partition@fd0000 {
|
||||
label = "factory";
|
||||
reg = <0xfd0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0>;
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "sgmii";
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&info 0x0>;
|
||||
phy-mode = "sgmii";
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
};
|
||||
|
||||
&usb_phy0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
@ -344,6 +344,14 @@ define Device/phicomm_k2t
|
||||
endef
|
||||
TARGET_DEVICES += phicomm_k2t
|
||||
|
||||
define Device/rosinson_wr818
|
||||
ATH_SOC := qca9563
|
||||
DEVICE_TITLE := ROSINSON WR818
|
||||
IMAGE_SIZE := 15872k
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
||||
endef
|
||||
TARGET_DEVICES += rosinson_wr818
|
||||
|
||||
define Device/wd_mynet-wifi-rangeextender
|
||||
ATH_SOC := ar9344
|
||||
DEVICE_TITLE := Western Digital My Net Wi-Fi Range Extender
|
||||
|
||||
Loading…
Reference in New Issue
Block a user