mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 05:38:00 +00:00
ath79: add support for TP-Link Archer C6 v2
This patch adds support for TP-Link Archer C6 v2 (EU) Hardware specification: - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q64CSIG (8MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: There's no UART header on the board Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing According to the GPL source the non-EU variant has different GPIOs assigned to some of the LEDs and buttons. The flash layout might be different as well. The wikidevi entry for Archer A6/C6 assumes they are identical. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
This commit is contained in:
Georgi Vlaev
Mathias Kresin
parent
9ebb44aef4
commit
d03aae1a09
@ -76,6 +76,10 @@ tplink,archer-c59-v1)
|
||||
ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x1E"
|
||||
ucidef_set_led_netdev "wan" "WAN" "tp-link:green:wan" "eth0"
|
||||
;;
|
||||
tplink,archer-c6-v2)
|
||||
ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x3C"
|
||||
ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x02"
|
||||
;;
|
||||
tplink,re450-v2)
|
||||
ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
|
||||
ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"
|
||||
|
||||
@ -154,6 +154,7 @@ ath79_setup_interfaces()
|
||||
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
||||
;;
|
||||
tplink,archer-a7-v5|\
|
||||
tplink,archer-c6-v2|\
|
||||
tplink,archer-c7-v5|\
|
||||
tplink,tl-wdr3600|\
|
||||
tplink,tl-wdr4300)
|
||||
|
||||
@ -155,7 +155,8 @@ case "$FIRMWARE" in
|
||||
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
||||
;;
|
||||
tplink,archer-c58-v1|\
|
||||
tplink,archer-c59-v1)
|
||||
tplink,archer-c59-v1|\
|
||||
tplink,archer-c6-v2)
|
||||
ath10kcal_extract "art" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary mac 8) -1)
|
||||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
|
||||
9
target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts
Normal file
9
target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts
Normal file
@ -0,0 +1,9 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "qca9563_tplink_archer-x6-v2.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "tplink,archer-c6-v2", "qca,qca9563";
|
||||
model = "TP-Link Archer C6 v2";
|
||||
};
|
||||
170
target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi
Normal file
170
target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi
Normal file
@ -0,0 +1,170 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &power;
|
||||
led-failsafe = &power;
|
||||
led-running = &power;
|
||||
led-upgrade = &power;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power: power {
|
||||
label = "tp-link:green:power";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "tp-link:green:wlan2g";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "tp-link:green:wlan5g";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "tp-link:green:lan";
|
||||
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "tp-link:green:wan";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_fail {
|
||||
label = "tp-link:amber:wan";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "tp-link:green:wps";
|
||||
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "Reset button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "WPS button";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
mac: partition@20000 {
|
||||
label = "mac";
|
||||
reg = <0x020000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x030000 0x7a0000>;
|
||||
};
|
||||
|
||||
partition@7d0000 {
|
||||
label = "tplink";
|
||||
reg = <0x7d0000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@7f0000 {
|
||||
label = "art";
|
||||
reg = <0x7f0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "sgmii";
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "sgmii";
|
||||
mtd-mac-address = <&mac 0x8>;
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&mac 0x8>;
|
||||
};
|
||||
@ -34,6 +34,16 @@ define Device/tplink_archer-c59-v1
|
||||
endef
|
||||
TARGET_DEVICES += tplink_archer-c59-v1
|
||||
|
||||
define Device/tplink_archer-c6-v2
|
||||
$(Device/tplink-safeloader-uimage)
|
||||
ATH_SOC := qca9563
|
||||
IMAGE_SIZE := 7808k
|
||||
DEVICE_TITLE := TP-LINK Archer C6 v2
|
||||
TPLINK_BOARD_ID := ARCHER-C6-V2
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||||
endef
|
||||
TARGET_DEVICES += tplink_archer-c6-v2
|
||||
|
||||
define Device/tplink_archer-c7-v1
|
||||
$(Device/tplink-8mlzma)
|
||||
ATH_SOC := qca9558
|
||||
|
||||
@ -548,6 +548,42 @@ static struct device_info boards[] = {
|
||||
.last_sysupgrade_partition = "file-system",
|
||||
},
|
||||
|
||||
/** Firmware layout for the C6v2 */
|
||||
{
|
||||
.id = "ARCHER-C6-V2",
|
||||
.vendor = "",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"{product_name:Archer C6,product_ver:2.0.0,special_id:45550000}\r\n"
|
||||
"{product_name:Archer C6,product_ver:2.0.0,special_id:52550000}\r\n"
|
||||
"{product_name:Archer C6,product_ver:2.0.0,special_id:4A500000}\r\n",
|
||||
.support_trail = '\x00',
|
||||
.soft_ver = "soft_ver:1.0.0\n",
|
||||
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x20000},
|
||||
{"default-mac", 0x20000, 0x00200},
|
||||
{"pin", 0x20200, 0x00100},
|
||||
{"product-info", 0x20300, 0x00200},
|
||||
{"device-id", 0x20500, 0x0fb00},
|
||||
{"firmware", 0x30000, 0x7a9400},
|
||||
{"soft-version", 0x7d9400, 0x00100},
|
||||
{"extra-para", 0x7d9500, 0x00100},
|
||||
{"support-list", 0x7d9600, 0x00200},
|
||||
{"profile", 0x7d9800, 0x03000},
|
||||
{"default-config", 0x7dc800, 0x03000},
|
||||
{"partition-table", 0x7df800, 0x00800},
|
||||
{"user-config", 0x7e0000, 0x0c000},
|
||||
{"certificate", 0x7ec000, 0x04000},
|
||||
{"radio", 0x7f0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "file-system",
|
||||
},
|
||||
|
||||
|
||||
/** Firmware layout for the C60v1 */
|
||||
{
|
||||
.id = "ARCHER-C60-V1",
|
||||
@ -1624,6 +1660,9 @@ static void build_image(const char *output,
|
||||
} else if (strcasecmp(info->id, "ARCHER-A7-V5") == 0 || strcasecmp(info->id, "ARCHER-C7-V4") == 0 || strcasecmp(info->id, "ARCHER-C7-V5") == 0) {
|
||||
const char mdat[11] = {0x01, 0x00, 0x00, 0x02, 0x00, 0x00, 0xca, 0x00, 0x01, 0x00, 0x00};
|
||||
parts[5] = put_data("extra-para", mdat, 11);
|
||||
} else if (strcasecmp(info->id, "ARCHER-C6-V2") == 0) {
|
||||
const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00};
|
||||
parts[5] = put_data("extra-para", mdat, 11);
|
||||
}
|
||||
|
||||
size_t len;
|
||||
|
||||
Loading…
Reference in New Issue
Block a user