This commit adds support for the Cisco Meraki MX64 and MX65 devices which
use the Broadcom NSP SoC, which is compatible with the bcm53xx platform.
MX64 Hardware info:
- CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
- RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
- Storage: 1 GB (Micron MT29F8G08ABACA)
- Networking: BCM58625 internal switch (5x 1GbE ports)
- USB: 1x USB2.0
- Serial: Internal header
MX65 Hardware info:
- CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
- RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
- Storage: 1 GB (Micron MT29F8G08ABACA)
- Networking: BCM58625 switch (2x 1GbE ports, used for WAN ports 1 & 2)
2x Qualcomm QCA8337 switches (10x 1GbE ports, used for LAN ports 3-12)
- PSE: Broadcom BCM59111KMLG connected to LAN ports 11 & 12
- USB: 1x USB2.0
- Serial: Internal header
Notes:
- The Meraki provided GPL source are available at [2].
- Wireless capability on the MX64W and MX65W exists in the form of 2x
Broadcom BCM43520KMLG, which is not supported. These devices will work
otherwise as standard MX64 or MX65 devices.
- Early MX64 units use an A0 variant of the BCM958625 SoC which lacks
cache coherency and uses a different "secondary-boot-reg". As a
consequence a different device tree is needed.
- Installation of OpenWrt requires changing u-boot to a custom version.
This is due to the stock u-boot "nand read" command being limited to
load only 2MB, in spite of the bootkernel1 and bootkernel2 partitions
both being 3MB in the stock layout. It is also required to allow
booting via USB, enabling cache coherency and setting up the QCA
switches and Serdes link on the MX65. The modified sources for U-boot
are available for the MX64[3] and MX65[4].
- Initial work on this device used a small bootloader within the OEM
partition scheme. To allow booting of larger kernels, UBI and bootm
support has been added, along with ability to store env variables to
the NAND. The Shmoo and newly created env partitions have been moved
to the extra space available after the nvram data.
- Users who installed the previous non-UBI supporting bootloader will
need to convert to the new one before flashing a compatible image.
These steps are detailed below.
References:
[1] https://www.broadcom.com/products/embedded-and-networking-processors/c
ommunications/bcm5862x
[2] https://dl.meraki.net/wired-14-39-mx64-20190426.tar.bz2
[3] https://github.com/clayface/U-boot-MX64-20190430_MX64
[4] https://github.com/clayface/U-boot-MX64-20190430_MX65
Installation guide:
Initial installation steps:
1. Compile or obtain OpenWrt files for the MX64 or MX65, including
u-boot[3][4], initramfs and sysupgrade images.
2. A USB disk with DOS partition scheme and primary FAT partition is
required.
3. If installing onto an MX64, set up a local web server.
4. On the device, boot into diagnostic mode by holding reset when
powering on the device. Continue to hold reset until the orange LED
begins to flash white. On used units the white flash may be difficult
to see.
5. Plug an Ethernet cable into the first LAN port, set the host to
192.168.1.2 and confirm telnet connectivity to 192.168.1.1.
U-boot installation - MX64 Only:
1. Newer fw versions require extra steps to support OpenWrt. To check,
please connect via telnet and run:
`cat /sys/block/mtdblock0/ro`
If the result is 1, your mtd0 is locked will need to perform extra
steps 4 and 5 in this section. If the result is 0 then skip these.
2. Check which SoC is in use by running the following command:
`devmem 0x18000000`
If devmem is not found then try:
`devmem2 0x18000000`
If the output begins with anything between "0x3F00-0x3F03" you will
need to use the A0 release. For any other output, eg "0x3F04" or
higher, use the regular MX64 image.
3 Confirm the size of the device's boot(mtd0) partition. In most
cases it should be 0x100000 or larger. If this is the case, please
proceed to use the uboot_mx64 image. If the reported size is
0x80000, please use the uboot_mx64_small image, then follow the
later guide to change to the larger image.
`cat /proc/mtd`
Example output:
`# cat /proc/mtd
cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00040000 "boot"
mtd1: 00080000 00040000 "shmoo"
mtd2: 00300000 00040000 "bootkernel1"
mtd3: 00100000 00040000 "nvram"
mtd4: 00300000 00040000 "bootkernel2"
mtd5: 3f700000 00040000 "ubi"
mtd6: 40000000 00040000 "all"`
4. Set up a webserver to serve the appropriate uboot_mx64 from the
following location and verify the SHA512:
https://github.com/clayface/U-boot-MX64-20190430_MX64
5. (Only if mtd0 is locked) You will also need the mtd-rw.ko kernel
module to unlock the partition from the same repo. An mtd executable
is also needed to write the mtd block. Place these on the web server
as well.
6. (Only if mtd0 is locked) Use wget to retrieve the files on the MX64:
`wget http://192.168.1.2/mtd-rw.ko`
`insmod mtd-rw.ko i_want_a_brick=1`
and confirm the unlock is set with dmesg
`mtd-rw: mtd0: setting writeable flag`
7. Download the appropriate u-boot image according to step 3. If you
did not need to unlock the mtd0 partition then use dd to write the
file, with caution:
`wget http://192.168.1.2/uboot_mx64`
`dd if=uboot_mx64 of=/dev/mtdblock0`
If you needed to unlock the mtd0 partition using the mtd-rw module,
run these commands instead to install u-boot instead:
`wget http://192.168.1.2/mtd`
`chmod +x mtd`
`wget http://192.168.1.2/uboot_mx64`
`./mtd write uboot_mx64 /dev/mtd0`
8. Once this has successfully completed, power off the device. If you
did not need to install the small u-boot image, proceed to
"OpenWrt Installation". Otherwise proceed to "UBI supporting
bootloader installation".
U-boot installation - MX65 Only:
1. Obtain telnet access to the MX65.
2. Confirm the size of the device's boot(mtd0) partition. In most
cases it should be 0x100000 or larger. If this is the case, please
proceed to use the uboot_mx65 image. If the reported size is
0x80000, please use the uboot_mx65_small image, then follow the
later guide to change to the larger image.
`cat /proc/mtd`
3. Prepare a USB drive formatted to FAT. Download the appropriate
uboot_mx65 to the USB drive from the following location and verify
the SHA512:
https://github.com/clayface/U-boot-MX64-20190430_MX65
3. Once you have telnet access to the MX65, plug in the USB disk and
run the following commands, with caution. The USB disk should
automount but if it does not, you will need to power off and on
again with reset held. Depending on step 2, use the uboot_mx65 or
uboot_mx65_small image accordingly:
`cd /tmp/media/sda1`
`dd if=uboot_mx65 of=/dev/mtdblock0`
4. Once this has successfully completed, power off the device. If you
did not need to install the small u-boot image, proceed to
"OpenWrt Installation". Otherwise proceed to "UBI supporting
bootloader installation".
UBI supporting bootloader installation:
These steps need to be followed if the older u-boot image was
installed, either because the Meraki diagnostic partition scheme used
0x80000 as the mtd0 size, or because you installed the u-boot provided
while OpenWrt support was still under development. If using OpenWrt,
please make a backup before proceeding.
1. Obtain the relevant image from the MX64(A0) or MX65 u-boot repo:
`openwrt-bcm5862x-generic-meraki_XXXX-initramfs-kernel.bin`
2. With the USB drive already inserted, power on the device while
holding the reset button. A white/orange flashing pattern will
occur shortly after power on. Let go of the reset button. The
device is now booting into OpenWrt initramfs stored on the USB
disk.
3. Connect by SSH to 192.168.1.1 and flash the embedded u-boot image,
changing X as appropriate:
`mtd write /root/uboot_mx6X /dev/mtd0`
You do not need to reboot as this image can handle "Kernel-in-UBI"
OpenWrt installation.
4. You can proceed to obtain and flash the appropriate OpenWrt image
at "OpenWrt Installation" Step 3.
5. Reboot will take significantly longer due to Shmoo calibration. In
case the device does not come online after several minute, power-
cycle the device and see if it boots. If you see an orange/white
flashing pattern, this indicates UBI booting was not successful and
you will need to copy a new bcm53xx image to a USB disk before
booting it and attempting to install OpenWrt again - refer to
"OpenWrt Installation" step 1. Do not attempt to reflash u-boot in
this scenario.
OpenWrt Installation:
1. Having obtained an OpenWrt image, please copy the file
`openwrt-bcm53xx-generic-meraki_XXXX-initramfs.bin`
to the base directory of a FAT formatted USB drive using DOS
partition scheme ,where XXXX is mx64, mx64_a0 or mx65 depending on
which device you have.
2. With the USB drive already inserted, power on the device. Boot time
will be longer than usual while Shmoo calibration takes place. A
different white/orange flashing pattern will eventually occur to
indicate device is now booting into OpenWrt initramfs stored on the
USB disk.
3. Ensuring Ethernet is plugged into a LAN port with IP set in the
192.168.1.0/24 subnet excluding 192.168.1.1, use SCP to copy the
sysupgrade file to 192.168.1.1:/tmp, eg:
`scp openwrt-bcm53xx-generic-meraki_XXXX-squashfs.sysupgrade.bin\
192.168.1.1:/tmp`
4. Connect by SSH to 192.168.1.1 and run sysupgrade:
`sysupgrade \
/tmp/openwrt-bcm53xx-generic-meraki_XXXX-squashfs.sysupgrade.bin`
5. OpenWrt should now be installed on the device.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
[ Rebase kernel configuration for 6.6,
fix failsafe by making kmod-eeprom-at24 and kmod-dsa-qca8k built-in,
resolve conflicts,
add LED aliases,
fix eth0 MAC address at probe ]
TODO:
- fix multiple LED colors not applied despite aliases - due to custom
/etc/diag.sh
- fix race condition between preinit and probing of the DSA tree,
causing no network interface available in failsafe mode (in general
case - to allow moving drivers back to modules)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable support for qca8k switch used in Meraki MX65. This is required to
properly support preinit networking on this device, otherwise unit won't
be accessible in failsafe mode.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required for the AT24 EEPROM holding MAC address on Meraki
devices to probe before preinit starts, so all network devices can be
available at the preinit network setup starts
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Meraki MX6x devices use them to store MAC address, so it is required to be
built-in for networking to probe properly, before preinit network setup
happens, which in turn is required for proper failsafe mode access.
Enable CONFIG_EEPROM_AT24 for the target.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch is required to support reading MAC address on Meraki MX64/65
line of devices, but also touches MR32, so let's backport it first.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds "REQUIRE_IMAGE_METADATA=1" requirement for the MR26 and
MR32, with REQUIRE_IMAGE_METADATA explicitly 0 elsewhere. This is based
upon bcm63xx's base-files/lib/upgrade/platform.sh.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Oversight from 8d302f5ebc , which requires
this to work. I couldn't test it as I ended up wiping my UBI volume by
accident.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is needed in order to get a MAC address from UBI.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
linux,ubi expects the volname variable, not volume.
This will fix NVMEM-on-UBI.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
make kernel_oldconfig doesn't seem to work with this. Handle manually.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adjusts the default config to modern kernels.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ImageBuilder when using the profile for the OpenWrt One has been
failing because the initramfs image included in the ubinized image could
not be found.
Fix that by using the staged initramfs instead when using the
ImageBuilder.
Fixes: 797904b3cb ("mediatek/filogic: add OpenWrt One support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Introduce EN7581 SoC support with currently rfb board supported.
This is a new 64bit SoC from Airoha that is currently almost fully
supported upstream with only the DTS missing. Setting source-only
waiting for the full upstream support to be completed.
Link: https://github.com/openwrt/openwrt/pull/16730
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport alloc_netdev_dummy patch from upstream needed for new Airoha
EN7581 SoC.
Refresh all affected patch with make target/linux/refresh.
Link: https://github.com/openwrt/openwrt/pull/16730
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In preparation for EN7581 SoC support, move en7523 in dedicated
subtarget.
This is needed as EN7581 is now 64bit but en7523 is 32bit hence have
very different kernel config.
Also rename patch to a more friendly number sequence.
Link: https://github.com/openwrt/openwrt/pull/16730
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9531 + QCA9886.
Short specification:
- 1x 10/100 Mbps Ethernet, with PoE support (wan/eth1)
- 1x 10/100/1000 Mbps Ethernet, with PoE support (lan/eth0)
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n (wlan2g)
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2 (wlan5g)
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- separate watchdog chip via GPIO (bottom of PCB?)
- UART header on PCB with proper labelling
Markings on PCB:
* R121QH_VER2.1 (silkscreen, bottom)
* CF-WA800 (sticker, top)
Initial flashing instructions:
Original firmware is based on OpenWrt.
a) Use sysupgrade image directly in vendor GUI.
b) Or via tftp:
ipaddr=192.168.1.1
serverip=192.168.1.10
bootfile="firmware.bin"
c) Or possibly via u-boot's `httpd` command.
MAC-address mapping follows original firmware:
* eth1 (wan) is the lowest mac address (art @ 0x0)
* eth0 (lan) uses eth1 + 1 (art @ 0x1002)
* wlan2g (phy1) uses eth1 + 2 (art @ 0x06)
* wlan5g (phy0) uses eth1 + 10 (not present in art)
* unused MAC (eth1 + 3) (art @ 0x5006)
Art dump (`hexdump /dev/mtd1 |grep ZZZZ`):
0000000 ZZZZ XXXX XXX0 ZZZZ XXXX XXX2 ffff ffff
0001000 0202 ZZZZ XXXX XXX1 0000 0000 0000 0000
0005000 202f bd21 0101 ZZZZ XXXX XXX3 0000 2000
Root access to original firmware (only via UART) can be achieved by
making a backup of configuration from web interface. Backup contains
whole `/etc` directory...
Signed-off-by: Priit Laes <plaes@plaes.org>
Link: https://github.com/openwrt/openwrt/pull/16556
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix conditions for handling offloaded packets
Fixes: #13430
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set the physical switch to KEY_RFKILL, since its previous value
(KEY_SETUP) is unsupported. This should also make the KEY_RESET button
functional, by allowing the gpio-button-hotplug kmod to load.
Signed-off-by: Chris Jones <cmsj@tenshu.net>
Link: https://github.com/openwrt/openwrt/pull/16564
Signed-off-by: Robert Marko <robimarko@gmail.com>
AT803X_PHY was replaced with QCA83XX_PHY which handles external switches.
But for internal ones like in the Meraki MR24, AT803X_PHY is needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16737
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qpic DMA controller is used by the parallel NAND Flash
interface. We don't need to enable it when nand-controller node
is marked as disabled.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mikrotik seems to prefer "hEX S" as general name for this model,
therefore include this in devicetree model name as well.
Signed-off-by: Priit Laes <plaes@plaes.org>
Link: https://github.com/openwrt/openwrt/pull/16658
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Increase usage of devm to get rid of goto and _remove.
Get rid of hw_reset_count. It's not really used for anything.
Use dev_err_probe to handle potential EPROBE_DEFER.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16588
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If LEDs are disabled, they should not be handled.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16651
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No longer need normal _remove function. Replaced with _disable.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16651
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WG1800HP2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 3T3R (Qualcomm Atheros QCA9880)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1800HP2 with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1800HP2 and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC addresses:
LAN : A4:12:42:xx:xx:44 (config, 0x6 (hex))
WAN : A4:12:42:xx:xx:45 (config, 0xc (hex))
2.4 GHz: A4:12:42:xx:xx:46 (config, 0x0 (hex))
5 GHz : A4:12:42:xx:xx:47 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WG1800HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 3T3R (Qualcomm Atheros QCA9880)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1800HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Downgrade the stock firmware to v1.0.2
4. After downgrading, select the OpenWrt initramfs-factory.bin image and
click update ("更新") button
5. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
6. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
7. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
8. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
9. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1800HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
- The data length of blocks in firmware image will be checked
(4M < threshold < 6M) on the stock WebUI on some versions (v1.0.28,
v1.0.30(latest), ...), so needs to be downgraded before OpenWrt
installation with initramfs-factory image.
MAC addresses:
LAN : 10:66:82:xx:xx:04 (config, 0x6 (hex))
WAN : 10:66:82:xx:xx:05 (config, 0xc (hex))
2.4 GHz: 10:66:82:xx:xx:06 (config, 0x0 (hex))
5 G : 10:66:82:xx:xx:07 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WG1400HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 2T2R (Qualcomm Atheros QCA9882)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1400HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1400HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC addresses:
LAN : 10:66:82:xx:xx:20 (config, 0x6 (hex))
WAN : 10:66:82:xx:xx:21 (config, 0xc (hex))
2.4 GHz: 10:66:82:xx:xx:22 (config, 0x0 (hex))
5 GHz : 10:66:82:xx:xx:23 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commonize function names of SGMII calibration functions of QCA955x added
for Meraki MR18, to use them for NEC Aterm series based on QCA9558 as
well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing reset bits of USB phys on QCA955x SoCs to qca955x.dtsi to
handle them.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems this was only used by one device in ar71xx. Might as well
reapply it.
Make use of the separate TX gain table for WZR-HP-G450H:
0f978bfaf2
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15949
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Gemtek WVRTM-127ACN is an indoor dual band wifi router
with internal antennas and 3 Gigabit Ethernet ports.
The Gemtek WVRTM-130ACN is an indoor dual band wifi router
with external antennas and 5 Gigabit Ethernet ports.
Hardware of WVRTM-127ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB
- Storage: 128 MB NAND SLC flash
- Ethernet: 3x 10/100/1000 Mbps LAN1,LAN2 & WAN
- Wireless: 2.4GHz: Mediatek MT7603EN (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 11x
- Buttons: 2x WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ IN (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-127ACN_V02" "19K-513-8500R" "RoHS" "1717"
Hardware of WVRTM-130ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB (Kioxia TC58BVG0S3HTA00)
- Storage: 128 MB NAND SLC (Winbond W971GG6SB-25)
- Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz and 5GHz Mediatek MT7615DN (802.11ac/b/g/n) (DBDC)
- LEDs: 10x
- Buttons: 3x Power, WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-130ACN_V01" "19K-515-4500R" "RoHS" "2112"
Enable access to uboot menu (needed in wvrtm-130acn):
- The access to uboot menu is blocked by `bootdelay = 0` set in ubootenv.
With stock firmware version 01.01.02.163 and previous, you can use CVE 2020-24365
command injection https://nvd.nist.gov/vuln/detail/CVE-2020-24365
python3 exploit.py -t 192.168.1.1 -c "fw_setenv bootdelay 3; fw_saveenv"
Backup the stock firmware:
- Connect via uart
- Connect via ethernet and assign your pc the address 192.168.15.x/24
- Power on the device; and start typing '4' to enter uboot menu
- Set factory mode and boot
MT7621 # setenv factory 2; saveenv
MT7621 # nand read 2800000 2000000 81000000; bootm
- Telnet and copy all mtd blocks
telnet 192.168.15.1
- Copy all mtd blocks and start webserver
for N in $(seq 0 6); do dd if=/dev/mtd$N of=/tmp/eeprom_mtd$N.bin; done
mount -o bind /tmp /www
lighttpd -f /etc/lighttpd.conf
- Backup stock rootfs_data (optional)
dd if=/dev/mtd7 of=/tmp/eeprom_mtd7.bin
dd if=/dev/mtd8 of=/tmp/eeprom_mtd8.bin
- Download to your pc from http://192.168.15.1/eeprom_mtd$N.bin
Installation:
- Connect via uart
- Connect via ethernet and assign your pc the address 10.10.10.3/24
- Start a tftp server and serve the image initramfs-kernel.bin
mkdir /tmp/ftpd;
cp initramfs-kernel.bin /tmp/ftpd/kernel.bin
dnsmasq --enable-tftp --tftp-root=/tmp/ftpd
- Power on the device; and start typing '4' to halt the bootloader
- Change the active mtd partition from mtd6 to mtd5 (needed by uboot)
MT7621 # setenv mtddevnum 5; saveenv
- Write the openwrt initramfs in ram via tftp and boot it
MT7621 # tftpboot 81000000 kernel.bin; bootm
- From the initramfs create the ubi device and install openwrt via sysupgrade
ubiformat /dev/mtd11 -y
sysupgrade -n -v /tmp/sysupgrade.bin
Recovery:
Restore the stock firmware from the backup of the mtd blocks
mtd write eeprom_mtd5.bin firmware
mtd write eeprom_mtd6.bin Kernel2
mtd write eeprom_mtd7.bin Storage1
mtd write eeprom_mtd8.bin Storage2
ubiformat /dev/mtd8 -y
reboot
Links to previous works on wvrtm-127acn:
https://github.com/digiampietro/hacking-gemtekhttps://forum.openwrt.org/t/add-support-for-gemtek-wvrtm-127acn-linkem-provider/168757
Signed-off-by: Samuele Longhi <agave@dracaena.it>
Link: https://github.com/openwrt/openwrt/pull/16685
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The swconfig-based b53 driver for the BCM53128 switch stopped working
after commits b2cfed48f6 (Revert "swconfig: fix Broadcom b53 support")
and e4e410733f (kernel: export switch_generic_set_link() symbol). This
rendered the 8 LAN ports of the EdgeSwitch 8XP non-functional, so the
image compilation for the device was disabled (5a1d7d8c1b).
This commit adds the kmod-dsa-b53-mdio and kmod-dsa-b53 packages
with the upstream B53 DSA driver, replacing the swconfig-based
kmod and kmod-switch-bcm53xx-mdio downstream ones that are not used by
any other device.
The 8 LAN ports of the EdgeSwitch 8XP are usable again. The 02_network
init script has been updated with the new DSA interfaces lan1 .. lan8.
Image building has been reenabled for the device, adding the usual DSA
incompatibility notice.
Tested on a Ubiquiti EdgeSwitch 8XP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Read WiFi calibration data via NVMEM framework. The MAC addresses are
stored inside a file on a filesystem and hence still have to be
extracted in userspace.
WiFI EEPROM extraction has already accidentally been partially removed
by commit 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran
devices").
Fixes: 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MAC-addresses are stored with colons, thus they can now be referenced
using NVMEM.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16310
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit 9ba0cae3cac07c21c583f9ff194f74043f90d29c made FSL_IFC
visible and selectable, which means that in order for MTD_NAND_FSL_IFC
to work, it needs these two extra CONFIG options.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16717
Signed-off-by: Robert Marko <robimarko@gmail.com>
In #16396, crashes were reported on MT7620, which were introduced by enabling
CONFIG_LIST_HARDENED. The cause seems to be random memory corruption somewhere
in the kernel. Unfortunately the crash traces do not point to the real cause
of the crash in any way.
Since MT7620 is really ancient hardware that likely only has few users left,
I don't expect that anybody will invest a significant amount of time to track
down the real cause. Because of that, let's disable CONFIG_LIST_HARDENED on
this target only, and leave it enabled on all other platforms.
Fixes: #16396
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add preinit script to rename network interfaces according to the
label provided in Device Tree.
Fixes: b6d8297510 ("mediatek: mt7622: add Adtran SmartRG SDG-841t6 device")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Two patches declared as accepted in v6.13 were already accepted for
v6.12. Fix filenames and order of patches applied.
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Fixes: 8cc049cec2 ("generic: phy: aquantia: move accepted patches to backport-6.6")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This driver allows retrieving MAC addresses and other factory information
via the NVMEM framework on Adtran devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building HWMON as module prevents some other drivers from getting built
into the kernel, e.g. mxl-gpy. Always enable HWMON and also set
THERMAL_HWMON.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport newly introduced support for 'active-high' property and use
it to correctly implement polarity assignment for Aquantia PHY LEDs.
Previously the 'active-low' property was used to switch a LED PIN to
active-high ("drive VDD" in Aquantia-speak) mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only add SerDes interface modes at lower speeds to host_interfaces.
Fixes: 5281033831 ("generic: net: phy: use all SerDes MAC interface modes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The snapshot builds for qoriq only contain ext4 images. Add squashfs to
FEATURES to also have the buildbots build squashfs images.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Dropping the source-only flag from qoriq and adding it to the buildbots
exposed a missing kernel config symbol: CONFIG_DRM_OFDRM. Addd it as
disabled to the qoriq kernel config, as the only device currently
supported in the qoriq target does not have any display hardware.
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The blamed commit adds a upgrade recipe for nas1dual to specify the
firmware partition name, but does not actually include the recipe that
will be called.
Since it previously relied on the default one, add that one.
Fixes: d21720fa90 ("mvebu: fix default partition name")
Link: https://github.com/openwrt/openwrt/pull/16704
Signed-off-by: Robert Marko <robimarko@gmail.com>
While the qoriq target currently supports only one device, the
WatchGuard Firebox M300, the feedback from people using it is that it's
a great bang for the buck. Additionally, people suggest having no
snapshots available hurts adoption.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The firmware partition name is specifc to ipTIME NAS1dual and should not be
set globally.
Fixes: #16148
Fixes: 6ff970bb51 ("mvebu: add support for ipTIME NAS1dual")
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16690
Signed-off-by: Robert Marko <robimarko@gmail.com>
73a9f9f857 added support. Let's use it.
Calibration data is not yet supported.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16256
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Beside the already existing control of the
Blue cover LED, this will also add the
Green and the Red cover LEDS available in the
Asus TUF-AX6000.
Signed-off-by: Magnus Sandin <magnus.sandin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution that is needed for some routers to provide proper
LED activity when controlled directly by the MV88E6xxx switch,
has just been merged in upstream Linux.
Make this patch 901 as other backports from earlier kernels
are in patch 896 and this is the first free number after
that.
Patch offsets in pending patches are augmented as part of
the refresh.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI driver framework can handle it automatically in
spi.c:spi_setup():spi_set_cs():gpiod_set_value_cansleep().
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16636
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ase subtarget supports two devices. ALLNET ALL0333CJ has one
Ethernet port and uses only the built-in MAC and PHY. The second
device is the Netgear DGN1000, which uses an AR8216 switch.
The driver for the adm6996 switch was probably accidentally
enabled instead of the ar8216 in commit that restores ase support
9b321bc60d ("lantiq: add Amazon-SE subtarget").
Before removing the ase subtarget, only ar8216 was enabled
c821836395 ("lantiq: remove unmaintained code").
Reduce uncompressed kernel size by 15.6 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15332
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15332
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport BLOCK OF support patch merged upstream and refresh pending
BLOCK patches.
This is a new way to declare partition table for BLOCK device (eMMC
currently supported) with the use of DTS.
Current pending patch are adapted to not cause regression with current
downstream implementation of a similar functionality.
Also enable the new OF_PARTITION config by default.
Link: https://github.com/openwrt/openwrt/pull/16663
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The bootloader can support zImage linux kernel which can decrease
the firmware image size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16662
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of forcing 2.5G PHYs into rate-adapter mode which results higher
energy consumption, lack of support for half-duplex modes and typically
worse performance when linked at speeds less than 2.5G, use SGMII mode
which allows the MAC to follow the PHY speed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Follow the advise of Russell King allows to greatly improve the driver
for RealTek's 1G and 2.5G Ethernet PHYs. The results are full/half
duplex as well as Gbit master/slave property being read from PHY
Specific Status Register (PHYSR), and fixes regarding link-partner
advertisement.
Fixes: #14504
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The previous iteration of MediaTek's PHY patches caused various weird bugs.
Drop culprit patch 733-10-net-phy-mediatek-Extend-1G-TX-RX-link-pulse-time.patch
and use the most recent iteration of the patchset which has been posted to the
netdev mailing list.
Link: https://patchwork.kernel.org/project/netdevbpf/list/?series=895513&state=*
Fixes: #16448
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
mutex_destroy is not called in any error paths or in _remove. Just use
devm to do so.
Removed a pointless platform_set_devdata call. Not needed with all of
the devm conversions.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16630
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also use devm for gpiochip_add_data.
Allows completely removing the _remove function.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16622
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification
-------------
- SoC : Qualcomm IPQ4019
- RAM : 256 MiB DDR3 (NT5CC128M16JR-EK)
- Flash : 64 MiB SPI NOR (Winbond W25Q512JVFQ)
- WLAN : IPQ4019 built-in
- 2.4 GHz : 2x2 MIMO WiFi4
- 5 GHz : 2x2 MIMO WiFi5
- Ethernet : QCA8075 10/100/1000 Mbps 1x WAN (ETH1, PoE); 1x LAN (ETH2)
- USB : 1x 2.0 Type-A
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
- LEDs : 1x RUN (lime & red)
1x WiFi 2.4 GHz (lime)
1x WiFi 5 GHz (lime)
2x ETH (lime), controlled by the QCA8075 phy
- Power : DC 12V & 802.3at PoE
- FCC ID : 2AHKT-WIA3300-20
- TFTP IP :
- client : 192.168.18.254
- router : 192.168.18.1
Installation
------------
1. Open uart console and start TFTP server. Copy initramfs image to
the TFTP root directory and rename it to 'ipqinitramfs.bin'.
2. Power on and press 'Enter' to exit to the u-boot console according
to the TTL log prompt.
3. Execute commands to load the initramfs image:
tftpboot && bootm
4. Enter into OpenWrt to backup the partitions if you want to restore
the stock firmware one day.
5. Override default 'bootcmd' environment variable in u-boot console:
env set bootcmd 'sf probe && sf read $loadaddr 0x980000 0x800000 && bootm $loadaddr'
env save
6. Repeat step 3 and flash 'sysupgrade' image in OpenWrt.
Recovery and return to stock
----------------------------
1. Restore the backup firmware partitions in the installation step 4.
2. Restore `bootcmd` environment variable via commands:
env set bootcmd bootipq && env save
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LABEL | xx:xx:xx:xx:xx:25 |
| LAN | xx:xx:xx:xx:xx:26 |
| WAN | xx:xx:xx:xx:xx:25 |
| WLAN 2g | xx:xx:xx:xx:xx:28 |
| WLAN 5g | xx:xx:xx:xx:xx:29 |
+---------+-------------------+
Notice
-----------
1. Some CH340 USB-TTL module doesn't work on this device.
2. The 'firmware' partition consists of four parts in the vendor
layout:
* Name Start Size
* rootfs 0x980000 0x1680000
* 0:HLOS1 0x2000000 0x800000
* rootfs_1 0x2800000 0x1400000
* rootfs_data 0x3c00000 0x350000
3. User can control the USB power supply via commands:
echo enabled > /sys/devices/platform/output-usb-power/state
echo disabled > /sys/devices/platform/output-usb-power/state
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16476
Signed-off-by: Robert Marko <robimarko@gmail.com>
It can be used to control the power on/off status for the fixed
voltage regulator via sysfs.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16476
Signed-off-by: Robert Marko <robimarko@gmail.com>
Even though optional is used, there's are still pointless NULL
assignments.
Use dev_err_probe to avoid manually handling EPROBE_DEFER.
Use devm_platform_iomap_resource. No struct resource needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Shiji Yang <yangshiji66@qq.com> on NETGEAR R6100.
Link: https://github.com/openwrt/openwrt/pull/16519
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
...conversion.
Commit 20736013e9 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
has causedt he device to no longer correctly read MAC address from its
onboard 24c64 EEPROM, because "at24" driver doesn't support legacy
nvmem-cell bindings [1] - and there was an explicit config option added
to mandate that behaviour in the following patch:
820-v6.7-0002-nvmem-add-explicit-config-option-to-read-old-syntax-.patch
But some of the devices, MR33 and MR74 included, weren't converted with
that as well.
Convert the definition to use proper fixed-layout binding to fix it.
The offending change was introduced between v23.05.0 and v23.05.1, and
found by bisection:
git bisect start
# status: waiting for both good and bad commits
# good: [bd4f415efa] OpenWrt v23.05.0: adjust config defaults
git bisect good bd4f415efa
# status: waiting for bad commit, 1 good commit known
# bad: [a58a86693f] OpenWrt v23.05.1: adjust config defaults
git bisect bad a58a86693f
# good: [3d0a78add2] qualcommax: only build initramfs if CONFIG_TARGET_ROOTFS_INITRAMFS is set
git bisect good 3d0a78add2
# bad: [21e5db97c4] build: add CycloneDX SBOM JSON support
git bisect bad 21e5db97c4
# good: [89184b15cf] mediatek: add build for MT7981 RFB
git bisect good 89184b15cf
# bad: [41f27bbb6d] bcm53xx: add the latest fix version of brcm_nvram
git bisect bad 41f27bbb6d
# good: [b649b0bf71] kernel: nvmem: fix "fixed-layout" & support "mac-base"
git bisect good b649b0bf71
# bad: [20736013e9] kernel: backport nvmem v6.6 fixes and v6.7 changes
git bisect bad 20736013e9
# good: [066971615f] kernel: backport v6.6 nvmem changes
git bisect good 066971615f
# first bad commit: [20736013e9] kernel: backport nvmem v6.6 fixes and v6.7 changes
Link: [1] https://github.com/openwrt/openwrt/issues/15393#issuecomment-2212300849
Fixes: 20736013e9 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
Fixes: https://github.com/openwrt/openwrt/issues/15393
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16623
Signed-off-by: Robert Marko <robimarko@gmail.com>
Avoids needing to call mutex_destroy in error paths, which is missing
anyway.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16620
Signed-off-by: Robert Marko <robimarko@gmail.com>
The u-boot,env driver does not have layout in compatible.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16616
Signed-off-by: Robert Marko <robimarko@gmail.com>
This fixes the build of the gemini and the apm821xx target.
The e2fsck application returns an error code now and that makes the
build fail. The tune2fs command adds an extra option and the e2fsck
should later fix the file system. It is intentionally broken in this
place.
e2fsprogs was patched before to ignore this error.
Fixes: 95e4664b5e ("tools: e2fsprogs: drop e2fsck patch")
Link: https://github.com/openwrt/openwrt/pull/16607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the absolute path to access the e2fsprogs applications. It is also
working with relative paths, but this makes sure that we use our
versions.
Link: https://github.com/openwrt/openwrt/pull/16607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set compatible string and specify redundant type U-boot environment.
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/16573
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable above drivers for mt7621 targets. They are needed for retrieving a MAC
address stored in a U-boot environment residing on an UBI volume.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/16573
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There's no specific fwnode handling here. Simpler to just use pdev.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16506
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use devm_gpiochip_add_data to get rid of the remove function. No need
for it.
Also use dev_err_probe to simplify the error path and avoid having to
handle -EPROBE_DEFER manually.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16506
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add CONFIG_ARCH_CONFIGURES_CPU_MITIGATIONS=y which was introduced
back in April of this year[1]
1. ce0abef6a1
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16535
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use more devm and remove _remove function.
Remove owner as the kernel sets it automatically.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16546
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently eth1 (which is the first "lan" interface) doesn't work on this device.
During boot the following can be seen in logs:
```
[ 2.252804] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.266060] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
[ 2.277889] mtk_soc_eth 1e100000.ethernet eth1: mediatek frame engine at 0xbe100000, irq 19
...
[ 2.355157] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.390312] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 2.398597] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 2.403872] mt7530-mdio mdio-bus:1f eth1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=21)
[ 2.416988] mtk_soc_eth 1e100000.ethernet eth0: error -17 registering interface eth1
[ 2.426973] mt7530-mdio mdio-bus:1f eth2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=22)
[ 2.440996] mt7530-mdio mdio-bus:1f eth3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=23)
[ 2.454405] mt7530-mdio mdio-bus:1f eth4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=24)
[ 2.467198] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 2.474117] DSA: tree 0 setup
...
[ 6.820998] mtk_soc_eth 1e100000.ethernet dsa: renamed from eth0
[ 6.919904] mtk_soc_eth 1e100000.ethernet wan: renamed from eth1
```
So the problem seems to be the fact that built-in gmacs get default
names (eth0/eth1) and are renamed after switch ports are initialized. This means
that when switch port with name `eth1` is brought up this name is still used by
gmac1 causing switch port's init to fail.
This patch just renames the ports to avoid name collision.
Note: this will break existing configs for this device because it renames all
the ports. This should not be major problem because this device doesn't have a
proper OEM image and is only flashable with serial access, meaning there should
not be many users.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15865
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification
----------------------
* RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
* 256MB DRAM
* 32MB NOR Flash
* 8 x 10/100/1000BASE-T ports
* 2 x SFP ports
* Power LED, Fault LED
* Reset button on front panel
* UART (115200 8N1) via populated standard pin header marked JP1
TODO: The SFP ports use a shared SCL GPIO that the driver cannot handle.
The left SFP port (lan9) is defined and fully functional while the laser
on the right SFP port (lan10) is off by default.
UART pinout
-----------
[o]ooo|JP1
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Installation using OEM webinterface
-----------------------------------
1. Make sure you are running OEM firmware in secondary slot
2. Install squashfs-factory.imag to primary slot by upload via http
Installation using serial interface
-----------------------------------
1. Press "a" "c" "p" during message "Enter correct key to stop autoboot"
2. Load image with "upgrade runtime <TFTP IP>:squashfs-sysupgrade.bin" command
3. Switch to primary slot with "setsys bootpartition 0"
4. Store config with "savesys"
5. Boot the image with `boota` command
Dual-boot with stock firmware using writable u-boot-env
-------------------------------------------------------
From stock to OpenWrt / primary image 1 (CLI as admin):
- > boot system image1
- > reboot
From OpenWrt to stock / boot image 2: (shell as root)
- # fw_setsys bootpartition 1
- # reboot
Debrick using serial interface
------------------------------
1. Press "a" "c" "p" during message "Enter correct key to stop autoboot"
2. Load vendor image with "upgrade runtime <TFTP IP>:LGS310xxxxx.imag"
3. switch to primary partition "setsys bootpartition 0"
4. safe config "savesys"
Further documentation
---------------------
See https://openwrt.org/toh/linksys/lgs352c
It has been developed and tested on device with v1 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16068
[Add missing 'w' in name of firmware partition]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Backport patch that fixes memory disclosure in packet padding.
The downstream driver supports statistics, so when a packet
cannot be padded the statistics of dropped packets are incremented.
The other patches do not introduce any functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/16563
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The cbr-reg DTS property uses a wrong name causing the RAC kernel
panic again on BCM6358 BCM6368 boards.
Use the correct cbr-reg name property.
Fixes: 7c9644a7b5 ("bmips: backport upstreamed RAC patches")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16561
Signed-off-by: Robert Marko <robimarko@gmail.com>
Select MT7996 2+3+3 firmware for the Adtran SmartRG SDG-8733A device
and also add it to the image for the BPi-R4 which supports both,
BE19000 (4+5+5) as well as BE14000 (2+3+3) Wi-Fi 7 modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This driver does not support more than 1 queue.
Fixes: ba24b94e0b ("ramips: use more devm in mtk_eth_soc")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
There are cases where an unavailable port is not an error, making
this error message a false-positive. The kernel log is flooded with
the messages like:
OF: graph: no port node found in /soc@0/bus@42000000/i2c@42530000/usb-typec@50
Silence this message by making it a debug message.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16524
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes some corner cases triggered by enabling fraglist GRO, where some
protocols may accidentally or intentionally linearize fraglist skbs.
Previously, these skbs became unusable and segmenting them led to crashes.
With this patch, they are properly handled by passing them to skb_segment
instead of skb_segment_list.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These got added to the kernel after this driver was written.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It automatically adds the error code at the end of the message. It also
deals with -EPROBE_DEFER automatically (doesn't output). Simpler code.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16350
Signed-off-by: Robert Marko <robimarko@gmail.com>
General hardware info:
----------------------
D-Link DGS-1210-28P rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC
@500MHz, DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE
capable with a total PoE power budget of 193W.
Power over Ethernet:
--------------------
The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU. In order to enable PoE, the
realtek-poe package is required. It is installed by default, but
currently it requires the manual editing of /etc/config/poe. Keep in
mind that the port number assignment does not match on this switch,
alway 8 ports are in reversed order: 8-1, 16-9 and 24-17.
LEDs and Buttons:
-----------------
On stock firmware, the mode button is supposed to switch the LED
indicators of all port LEDs between Link Activity and PoE status. The
currently selected mode is visualized using the respective LEDs. PoE Max
indicates that the maximum PoE budget has been reached. Since there is
currently no support for this behavior, these LEDs and the mode button
can be used independently.
Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.
Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd
OEM installation from Web Interface:
------------------------------------
1. Make sure you are booting using OEM in image 2 slot. If not,
switch to
image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image in vendor firmware via Tools > Backup / Upgrade
Firmware > image1
3. Toggle startup image via System > Firmware Information > Boot
from
image1
4. Tools > reboot
Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:
Boot initramfs image from U-Boot:
---------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000
openwrt-rtl838x-generic-d-link_dgs-1210-28p-f-initramfs-kernel.bin`
command
5. Boot the image with `bootm` command
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15938
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Before this commit, sysupgrade saved the settings backup data to
the area following rootfs even though the device has an actual
rootfs_data partition. The backup data was completely ignored on
the following boot, but since rootfs_data was not being cleared
during sysupgrade, the issue was not noticed earlier.
Note that this commit changes the filesystem of rootfs_data from
ext4 to F2FS (if OEM partitioning is used).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16463
Signed-off-by: Robert Marko <robimarko@gmail.com>
This board is also as known as Bananapi BPi-M7.
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
8/16/32GB LPDDR4/LPDDR4x RAM
2x 2500 Base-T (PCIe, rtl8125b)
2 LEDs (RED / GREEN)
16GB/32GB/64GB/128GB eMMC on-board
Micro-SD Slot
USB 2.0 Port
USB 3.0 Port
M.2 M-Key
40-Pin Header
USB PD 2.0 9/12/15V Power
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16462
Signed-off-by: Nick Hainke <vincent@systemli.org>
of_property_read_u32 returns -EINVAL when property does not exist,
according to the documentation -ENOENT is not a valid return code.
So, instead of checking for -ENOENT check for -EINVAL as otherwise the
blamed commit breaks AQR probe since it will return -EINVAL during probe.
Fixes: cb2a11f49c ("generic: phy: aquantia: add pending patch to force MDI pair order")
Link: https://github.com/openwrt/openwrt/pull/16466
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing ksym CONFIG_RUST
Building r27563 without this commit will fail due to this ksym
being undefined in the generic config.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16464
Signed-off-by: Robert Marko <robimarko@gmail.com>
We already have an kernel module package "kmod-phy-ath79-usb" to
drive the ath79 USB. It will be selected by the usb base package
"kmod-usb2" and "kmod-usb-ohci".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.
The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)
Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:
https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/
The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.
http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.
Alternatively, from a root shell on the running system, unlock the boot
partition with
echo 0 >/sys/block/mmcblk0boot0/force_ro
then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.
Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset
USB: Front V3.0 & Rear V2.0
MAC Table
Label xx:xx:xx:xx:xx:38
LAN xx:xx:xx:xx:xx:39
2.4Ghz xx:xx:xx:xx:xx:3A
5Ghz xx:xx:xx:xx:xx:3C
WAN xx:xx:xx:xx:xx:38
Flash Instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image
D-Link Fail Safe GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the fail safe GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the fail safe page for the device at http://192.168.0.1/
6. Use the provided fail safe web GUI to upload the factory.bin to the device
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16269
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Only one device uses the dtsi file "rt3883_belkin_f9k110x.dtsi".
So there is no need to split the device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16318
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 GHz WiFi doesn't work on the wmac of this device.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16318
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for W25N01JW, W25N02JWZEIF, W25N512GW, W25N02KWZEIR and W25N01GWZEIG.
Add support for W25N04KV.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16272
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SoC: MediaTek MT7621
Flash: 16MB (Macronix MX25L12805D)
RAM: 128MB
Serial: As marked on PCB, baudrate is 57600, DO NOT CONNECT 3.3V!!!
Ethernet: 4x 10/100/1000 Mbps (3x LAN + WAN)
WIFI0: MT7615 2.4GHz 802.11b/g/n
WIFI1: MT7615 5GHz 802.11ac
Antennas: 6x external (3 per radio), non-detachable
LEDs: Programmable power-LED (blue-colored)
Buttons: Reset
INSTALLATION:
Get rootshell using insructions from https://gist.github.com/ZIKH26/18693c67ee7d2f8d2c60231b19194c37
Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Download archive with firmware from Ruijie's site and
get .bin file from it. Then write that binary to firmware
partition. After reboot, factory-reset the router using
reset button.
Signed-off-by: Yahor Leonenka <staryjakau@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16202
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WSC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh extender,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 2x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/2x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 10.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:6E (Factory, 0x3fff4 (hex))
2.4 GHz: 04:AB:18:xx:xx:6F (Factory, 0x3fffa (hex))
5 GHz : 04:AB:18:xx:xx:70 (Factory, 0x4 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WMC-X1800GST is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh router,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 3x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/5x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:BF (Factory, 0x3fff4 (hex))
WAN : 04:AB:18:xx:xx:C0 (Factory, 0x3fffa (hex))
2.4 GHz: 04:AB:18:xx:xx:C1 (Factory, 0x4 (hex))
5 GHz : 04:AB:18:xx:xx:C2
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename the downstream ag71xx driver to ag71xx-legacy.
It allows both upstream and downstream drivers to be compiled into modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware Spec
-SoC: Rockchip RK3588S
CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
-RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
-Flash: 32GB/None eMMC, at HS400 mode
-Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
-USB: one USB 3.0 Type-A and one USB 2.0 Type-A
-PCIe: one M.2 Key M connector with PCIe 2.1 x1
-HDMI:
compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
support up to 7680x4320@60Hz
Support RGB/YUV(up to 10bit) format
-microSD: support up to SDR104 mode
-GPIO:
30-pin 2.54mm header connector
up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
-Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
-LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
-others:
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
MASK button for eMMC update
one user button
-Power supply: USB-C, support PD, 5V/9V/12V/20V input
-PCB: 8 Layer, 62x90x1.6mm
-Ambient Operating Temperature: 0℃ to 70℃
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
eMMC Installation:
Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport ir-receiver/minipcie/poweroff/spi/usb-c support and other
minor fixes for the NanoPC T6 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16443
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update sysupgrade script (fortinet.sh) for Fortinet devices in
mvebu/cortexa9 and fix the following issues,
- Some individuals of FortiGate/FortiWiFi 30E/5xE devices has wrong
kernel/rootfs offsets in "firmware-info" partition and they are not
updated with the current sysupgrade script for Fortinet devices
(fortinet.sh).
As a result, the bootloader tries to load kernel data from the wrong
address and boot with it after OpenWrt installation.
The new script handles offsets in addition to length values.
and improve the following points.
- Only 2 bytes are handled with the current sysupgrade script
(fortinet.sh) for kernel/rootfs length. The new script handles 4 bytes
instead.
- The image names of image0/image1 are not handled and not updated when
sysupgrade. The new sysupgrade script handles it and update to
"<dist> <version> <revision>" if firmware metadata is available.
(ex.: "OpenWrt SNAPSHOT r27440-25384026")
log of new sysupgrade script (fortinet.sh):
Tue Sep 17 10:29:16 UTC 2024 upgrade: Performing system upgrade...
Image Index: 0
Image Name : "OpenWrt SNAPSHOT r27440-25384026"
--> "OpenWrt SNAPSHOT r27441-b3a0806a05"
kernel:
old: 0x003c4e00@0x00200000
new: 0x003c4e00@0x00200000
rootfs:
old: 0x005c0200@0x00800000
new: 0x005c0200@0x00800000
Unlocking kernel ...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mdio bus number of mv88e6xxx was changed to '0' from '1' and the
"mv88e6xxx-1:<addr>:<speed>" triggers are unavailable now.
Update triggers for "SPEED" LEDs to make working that LEDs again.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver for fixed voltage regulater uses "regulator-fixed" for
compatible string, not "fixed-regulator".
Fixes: 102dc5a625 ("mvebu: add support for FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename the sysupgrade.tar step to sysupgrade.bin. The sysupgrade.tar is
used in other places and we prefer a sysupgrade.bin instead.
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.
This fixes the build of the ramips target.
Fixes: 665c2154ef ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change I2C pin flags to GPIO_ACTIVE_HIGH and change SDA to GPIO1.
On my late production GL-AR750 (purchased 2024):
SCL = GPIO16
SDA = GPIO1
Bug report:
I2C bus doesn't work in GL-AR750
https://github.com/openwrt/openwrt/issues/16319
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16406
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make the patches apply cleanly again.
Fixes: 3660ddb8ab ("generic: ar8216: remove support for Linux before version 6.1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification is similar to other devices of the MT Stuart series:
* Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 2500M/1000M/100M LAN port
* 10000M/5000M/2500M/1000M/100M/10M WAN port
* MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for the 2.5G port, 3x LED for the 10G port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The legacy swconfig switch driver framework supports kernels older than
Linux 6.6 by using #ifdef'ery with LINUX_VERSION_CODE. Remove all that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove folder with DTS files for Linux 6.1 which has already been
dropped.
Fixes: f142ce87d9 ("kirkwood: remove 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Support for Linux 6.1 has already been removed from the armsr target.
Remove left-over patches-6.1 folder as well.
Fixes: fd47fdf527 ("armsr: Remove kernel 6.1 configuration")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove left-over config-6.1 files which should have been removed
when removing kernel 6.1 support.
Fixes: f20987c161 ("layerscape: remove kernel 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the GPIO pin of the PoE passthrough switch on the Aruba AP-303H.
Power is activated when the pin is low. It enables a PSE chip, so power
is only supplied to downstream devices when they are 802.3af/at
compliant devices.
Ensure you use a sufficient power supply when chaining a consuming
device after the AP.
Signed-off-by: David Bauer <mail@david-bauer.net>
Increase QDMA RESV_BUF from 2K to 3K for netsys v2 to match Mediatek SDK.
This helps reduce the possibility of Ethernet transmit timeouts.
Link: 19d8456c30
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The purpose of resetting the TX queue is to reset the
byte and packet count as well as to clear the software
flow control XOFF bit.
MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.
Packets may stop being sent after reset and "transmit timeout" log may
be displayed.
Import fix from MediaTek's SDK to resolve this issue.
Link: 5746a94456
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This files are executable:
target/linux/ramips/dts/mt7621_openfi_5pro.dts
target/linux/ramips/dts/mt7621_winstars_ws-wn536p3.dts
Has to be fixed.
Fixes: 5560791 ("ramips: add support for OpenFi 5Pro Travel Router")
Fixes: 2da2705 ("ramips: add support for WINSTARS WS-WN536P3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of reading it from flash directly, let U-Boot assign the LAN
MAC address. Set label-mac-device while at it and sort aliases in DT
alphabetically.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kconfig symbols CONFIG_VIDEO_MICROCHIP_CSI2DC, CONFIG_VIDEO_MICROCHIP_ISC
and CONFIG_VIDEO_MICROCHIP_XISC are missing for sama5 and sama7 causing
the build to abort or waiting for user input. Add the symbols (disabled)
so build with Linux 6.6 succeeds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix a typo in the MAC address assignment script affecting SDG-8734.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware information:
---------------------
- SoC: RTL8393M
- Copper phy: 6×RTL8218B
- Fibre phy: RTL8214FC
- Flash: 32MiB SPI NOR, MX25L25635FMI
- RAM: 128MiB DDR3, Micron MT41K64M16TW-107
- Serial port: ±5V serial port to RJ45, ZT3232 (MAX3232 compatible)
- +370W POE on JG928A model
Note: SFP ports currently non-functional due to missing support for
RTL8214FC on the RTL8393M target.
Updated for Linux 6.6 kernel.
Installation:
-------------
- Initial installation follows same process as HPE 1920-24G (JG924A)
- Based on prior work of Jan Hoffmann <jan@3e8.eu>
- Additional work by Andreas Böhler <dev@aboehler.at>
- PoE updates and tidy-up by Stephen Howell <howels@allthatwemight.be>
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Now that there is 6.6 support for realtek, lets encourage testing it by
making it default so 5.15 can be dropped ASAP.
Link: https://github.com/openwrt/openwrt/pull/16408
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 'active-low' property was not applied correctly and two fixes
are required to make inverted LEDs work as expected.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The at91 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove obsolete patches no longer applicable to the 6.6 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove unnecessary dts files already included in the 6.1 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Siflower SF19A2890 is an SoC with:
Dual-core MIPS InterAptiv at 800MHz
DDR3 controller
One Gigabit Ethernet MAC with RGMII and IPv4 HNAT engine
Built-in 2x2 11N + 2x2 11AC WiFi radio
USB 2.0 OTG
I2C/SPI/GPIO and various other peripherals
This PR adds support for SF19A2890 EVB with ethernet support.
EVB spec:
Memory: DDR3 128M
Ethernet: RTL8367RB 5-port gigabit switch
Flash: 16M NOR
Others: MicroUSB OTG, LED x 1, Reset button x1
The built image can be flashed using u-boot recovery.
This target is marked as source-only until support for a commercial
router board comes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].
[0] https://forum.openwrt.org/t/206640
Signed-off-by: Andreas Böhler <dev@aboehler.at>
RELR is a relocation packing format for relative relocations.
Linux has supported using it for ARM64 since 5.4, and more recently
for LoongArch as well.
It requires compatible tooling as well, so only with binutils 2.43
TOOLS_SUPPORT_RELR is set and thus RELR available.
RELR should always decrease the binary size and while testing this
the default build for Dynalink WRX-36 (qualcommax/ipq807x) reduced
the compressed kernel size by 38k and uncompressed one by 640k.
So, lets enable it in the default config.
Link: https://github.com/openwrt/openwrt/pull/16403
Signed-off-by: Robert Marko <robimarko@gmail.com>
Merging of the realtek 6.6 series forgot to include some final fixes
for the new MDIO driver. What was changed in last second?
1. The MDIO driver used wrong constants to make use of the raw
page (for direct register access). Provide a rawpage variable in
the bus private structure, populate it during initialization and
make use of it at the proper places
2. We always used the variable portaddr for the bus index. Usually
our driver uses either addr or port for the same meaning. Remove the
duplication and reuse the normal addr variable.
3. Drop functions rtmdio_write_page() and rtmdio_read_page(). These
only call the PHY driver read/write page functions. We know that
these will only access page 0x1f. As we have only Realtek PHYs
and our driver only reacts to this special page, just hardcode it.
Benefit is that we can use these functions for PHY detection when
read/write page functions are not yet assigned.
4. Add two new helper functions phy_port_read_paged() and
phy_port_write_paged(). These allow to access arbitrary ports on
the MDIO bus when the packages are not initialized. These will be
needed for proper RTL8218B and RTL8214FC detection in forthcoming
patches.
5. The port tracking wrongly used index 0 to mark "normal" access.
This does not allow to make a "special" access to port 0. Use
index -1 to mark "normal" access.
Provide the fix for 5.15 and 6.6 to allow for easy version
comparison.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
With commit a22d359fa5 VLAN handling was fixed for kernel 6.6.
This restored network connectivity of the devices. For easy testing
backport the fix for 5.15 too.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
On the XGS1210-12 the RTL8218D is attached via XGMII. Add this to the
supported list in the DSA driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
We switched to 6.6, so lets remove 6.1 support now.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16099
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
