mirror of
https://github.com/openwrt/openwrt.git
synced 2025-02-20 09:26:28 +00:00
ath79: add support for NEC Aterm WG1400HP
NEC Aterm WG1400HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 2T2R (Qualcomm Atheros QCA9882)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1400HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1400HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC addresses:
LAN : 10:66:82:xx:xx:20 (config, 0x6 (hex))
WAN : 10:66:82:xx:xx:21 (config, 0xc (hex))
2.4 GHz: 10:66:82:xx:xx:22 (config, 0x0 (hex))
5 GHz : 10:66:82:xx:xx:23 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
INAGAKI Hiroshi
Hauke Mehrtens
parent
0e8af9f5a7
commit
2aed68b75f
371
target/linux/ath79/dts/qca9558_nec_aterm.dtsi
Normal file
371
target/linux/ath79/dts/qca9558_nec_aterm.dtsi
Normal file
@ -0,0 +1,371 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
#include "qca955x.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
/*
|
||||
* don't specify bootargs property in DeviceTree to
|
||||
* enable a console with a default baudrate (9600)
|
||||
* or passed console= parameter from the bootloader
|
||||
*/
|
||||
/delete-property/ bootargs;
|
||||
stdout-path = &uart0;
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
label-mac-device = ð0;
|
||||
};
|
||||
|
||||
i2c {
|
||||
compatible = "i2c-gpio";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmx_gpio_i2c_pins>;
|
||||
sda-gpios = <&gpio 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
gpio1: gpio@20 {
|
||||
compatible = "ti,tca6416";
|
||||
reg = <0x20>;
|
||||
reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
|
||||
usb-hub-reset {
|
||||
gpio-hog;
|
||||
gpios = <0 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&jtag_disable_pins>;
|
||||
|
||||
button-wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
button-eco {
|
||||
label = "eco";
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
switch-bridge {
|
||||
label = "br";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
switch-converter {
|
||||
label = "cnv";
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_2>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-0 {
|
||||
gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = "converter";
|
||||
};
|
||||
|
||||
led-1 {
|
||||
label = "green:converter";
|
||||
gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = "converter";
|
||||
};
|
||||
|
||||
led-2 {
|
||||
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = "tv";
|
||||
};
|
||||
|
||||
led-3 {
|
||||
gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = "tv";
|
||||
};
|
||||
|
||||
led-4 {
|
||||
gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WLAN_5GHZ;
|
||||
};
|
||||
|
||||
led-5 {
|
||||
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN_5GHZ;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
led-6 {
|
||||
gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
};
|
||||
|
||||
led-7 {
|
||||
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
led-8 {
|
||||
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WAN_ONLINE;
|
||||
};
|
||||
|
||||
led-9 {
|
||||
gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WAN_ONLINE;
|
||||
};
|
||||
|
||||
led_power_red: led-10 {
|
||||
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
};
|
||||
|
||||
led_power_green: led-11 {
|
||||
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
default-state = "on";
|
||||
};
|
||||
};
|
||||
|
||||
regulator {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "usb-vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
/*
|
||||
* since the OEM bootloader requires unknown
|
||||
* filesystem on firmware area, needs to be
|
||||
* replaced to u-boot before OpenWrt installation
|
||||
*/
|
||||
partition@0 {
|
||||
label = "bootloader";
|
||||
reg = <0x000000 0x020000>;
|
||||
};
|
||||
|
||||
/* not compatible with u-boot */
|
||||
partition@20000 {
|
||||
label = "config";
|
||||
reg = <0x020000 0x010000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_config_0: macaddr@0 {
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
|
||||
macaddr_config_6: macaddr@6 {
|
||||
reg = <0x6 0x6>;
|
||||
};
|
||||
|
||||
macaddr_config_c: macaddr@c {
|
||||
reg = <0xc 0x6>;
|
||||
};
|
||||
|
||||
macaddr_config_12: macaddr@12 {
|
||||
reg = <0x12 0x6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "art";
|
||||
reg = <0x030000 0x010000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
cal_art_1000: calibration@1000 {
|
||||
reg = <0x1000 0x440>;
|
||||
};
|
||||
|
||||
cal_art_5000: calibration@5000 {
|
||||
reg = <0x5000 0x844>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x040000 0xfc0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x00080080 /* PORT0_PAD_MODE_CTRL */
|
||||
0x08 0x00000000 /* PORT5_PAD_MODE_CTRL */
|
||||
0x0c 0x07600000 /* PORT6_PAD_MODE_CTRL */
|
||||
0x10 0xa12613a0 /* POWER_ON_STRAP */
|
||||
0x50 0xcc36cc36 /* LED_CTRL0 */
|
||||
0x54 0xca36ca36 /* LED_CTRL1 */
|
||||
0x58 0xc936c936 /* LED_CTRL2 */
|
||||
0x5c 0x03ffff00 /* LED_CTRL3 */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
0x94 0x0000007e /* PORT6_STATUS */
|
||||
0xe0 0xc74164d0 /* SGMII_CONTROL */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&macaddr_config_c>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
phy-handle = <&phy0>;
|
||||
qca955x-sgmii-fixup;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
|
||||
rgmii-enabled = <1>;
|
||||
rxdv-delay = <2>;
|
||||
rxd-delay = <2>;
|
||||
};
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&macaddr_config_6>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
pll-data = <0x03000000 0x00000101 0x00001616>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gpio {
|
||||
switch-reset {
|
||||
gpio-hog;
|
||||
gpios = <11 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "pci168c,003c";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cells = <&cal_art_5000>, <&macaddr_config_12>;
|
||||
nvmem-cell-names = "calibration", "mac-address";
|
||||
};
|
||||
};
|
||||
|
||||
&pinmux {
|
||||
/* mux GPIO19/20 as GPIO instead of native I2C on QCA9558 */
|
||||
pmx_gpio_i2c_pins: gpio-i2c-pins {
|
||||
pinctrl-single,bits = <0x10 0x0 0xff000000>,
|
||||
<0x14 0x0 0xff>;
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
dr_mode = "host";
|
||||
|
||||
/delete-node/ port@1;
|
||||
|
||||
/* NEC uPD720114 */
|
||||
hub@1 {
|
||||
compatible = "usb0409,005a";
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&cal_art_1000>, <&macaddr_config_0>;
|
||||
nvmem-cell-names = "calibration", "mac-address";
|
||||
};
|
||||
12
target/linux/ath79/dts/qca9558_nec_wg1400hp.dts
Normal file
12
target/linux/ath79/dts/qca9558_nec_wg1400hp.dts
Normal file
@ -0,0 +1,12 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca9558_nec_aterm.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "nec,wg1400hp", "qca,qca9558";
|
||||
model = "NEC Aterm WG1400HP";
|
||||
};
|
||||
|
||||
ð0 {
|
||||
pll-data = <0x5a000000 0x00000101 0x00001616>;
|
||||
};
|
||||
@ -189,6 +189,7 @@ ath79_setup_interfaces()
|
||||
;;
|
||||
belkin,f9j1108-v2|\
|
||||
belkin,f9k1115-v2|\
|
||||
nec,wg1400hp|\
|
||||
tplink,archer-c5-v1|\
|
||||
tplink,archer-c7-v1|\
|
||||
tplink,archer-c7-v2|\
|
||||
|
||||
@ -17,6 +17,15 @@ platform_check_image() {
|
||||
ubnt,routerstation-pro)
|
||||
platform_check_image_redboot_fis "$1"
|
||||
;;
|
||||
nec,wg1400hp)
|
||||
local uboot_mtd=$(find_mtd_part "bootloader")
|
||||
|
||||
# check "U-Boot <year>.<month>" string in the "bootloader" partition
|
||||
if ! grep -q "U-Boot [0-9]\{4\}\.[0-9]\{2\}" $uboot_mtd; then
|
||||
v "The bootloader doesn't seem to be replaced to U-Boot!"
|
||||
return 1
|
||||
fi
|
||||
;;
|
||||
*)
|
||||
return 0
|
||||
;;
|
||||
|
||||
@ -1,4 +1,5 @@
|
||||
include ./common-buffalo.mk
|
||||
include ./common-nec.mk
|
||||
include ./common-netgear.mk
|
||||
include ./common-senao.mk
|
||||
include ./common-tp-link.mk
|
||||
@ -2060,6 +2061,16 @@ define Device/nec_wg1200cr
|
||||
endef
|
||||
TARGET_DEVICES += nec_wg1200cr
|
||||
|
||||
define Device/nec_wg1400hp
|
||||
SOC := qca9558
|
||||
DEVICE_MODEL := Aterm WG1400HP
|
||||
IMAGE_SIZE := 16128k
|
||||
NEC_FW_TYPE := H040b
|
||||
$(Device/nec-netbsd-aterm)
|
||||
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
||||
endef
|
||||
TARGET_DEVICES += nec_wg1400hp
|
||||
|
||||
define Device/nec_wg800hp
|
||||
SOC := qca9563
|
||||
DEVICE_VENDOR := NEC
|
||||
|
||||
@ -741,5 +741,7 @@
|
||||
#define QCA955X_ETH_CFG_SGMII_GMAC0 BIT(6)
|
||||
|
||||
#define QCA955X_GMAC_REG_SGMII_SERDES 0x0018
|
||||
#define QCA955X_GMAC_REG_MR_AN_CONTROL 0x1c
|
||||
#define QCA955X_GMAC_REG_SGMII_CONFIG 0x34
|
||||
|
||||
#endif /* __ASM_MACH_AR71XX_REGS_H */
|
||||
|
||||
@ -51,7 +51,8 @@ static void tlwr1043nd_init(void)
|
||||
static inline void tlwr1043nd_init(void) {}
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BOARD_MERAKI_MR18)
|
||||
#if defined(CONFIG_BOARD_MERAKI_MR18) || \
|
||||
defined(CONFIG_BOARD_NEC_WG1400HP)
|
||||
|
||||
static int extract_qca955x_sgmii_res_cal(void)
|
||||
{
|
||||
@ -215,26 +216,14 @@ static inline void huawei_ap_init(void)
|
||||
static inline void huawei_ap_init(void) {}
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BOARD_NEC_WG600HP) || \
|
||||
#if defined(CONFIG_BOARD_NEC_WG1400HP) || \
|
||||
defined(CONFIG_BOARD_NEC_WG600HP) || \
|
||||
defined(CONFIG_BOARD_NEC_WR8750N) || \
|
||||
defined(CONFIG_BOARD_NEC_WR9500N)
|
||||
|
||||
#define AR934X_PLL_SWITCH_CLK_CTRL_REG 0x24
|
||||
#define AR934X_PLL_SWITCH_CLK_CTRL_SWITCHCLK_SEL BIT(0)
|
||||
|
||||
static inline void nec_aterm_init(void)
|
||||
static inline void nec_aterm_reset_common(void)
|
||||
{
|
||||
unsigned int reg, val;
|
||||
unsigned int reg = KSEG1ADDR(AR71XX_RESET_BASE);
|
||||
|
||||
printf("NEC Aterm series (AR9344)\n");
|
||||
|
||||
/* set REFCLK=40MHz to switch PLL */
|
||||
reg = KSEG1ADDR(AR71XX_PLL_BASE);
|
||||
val = READREG(reg + AR934X_PLL_SWITCH_CLK_CTRL_REG);
|
||||
val &= ~AR934X_PLL_SWITCH_CLK_CTRL_SWITCHCLK_SEL;
|
||||
WRITEREG(reg + AR934X_PLL_SWITCH_CLK_CTRL_REG, val);
|
||||
|
||||
reg = KSEG1ADDR(AR71XX_RESET_BASE);
|
||||
#ifndef LOADADDR
|
||||
/*
|
||||
* This is for initramfs-factory image.
|
||||
@ -264,6 +253,29 @@ static inline void nec_aterm_init(void)
|
||||
* booting from stock bootloader
|
||||
*/
|
||||
WRITEREG(reg + AR71XX_RESET_REG_WDOG, 0xffffffff);
|
||||
}
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BOARD_NEC_WG600HP) || \
|
||||
defined(CONFIG_BOARD_NEC_WR8750N) || \
|
||||
defined(CONFIG_BOARD_NEC_WR9500N)
|
||||
|
||||
#define AR934X_PLL_SWITCH_CLK_CTRL_REG 0x24
|
||||
#define AR934X_PLL_SWITCH_CLK_CTRL_SWITCHCLK_SEL BIT(0)
|
||||
|
||||
static inline void nec_aterm_init(void)
|
||||
{
|
||||
unsigned int reg, val;
|
||||
|
||||
printf("NEC Aterm series (AR9344)\n");
|
||||
|
||||
/* set REFCLK=40MHz to switch PLL */
|
||||
reg = KSEG1ADDR(AR71XX_PLL_BASE);
|
||||
val = READREG(reg + AR934X_PLL_SWITCH_CLK_CTRL_REG);
|
||||
val &= ~AR934X_PLL_SWITCH_CLK_CTRL_SWITCHCLK_SEL;
|
||||
WRITEREG(reg + AR934X_PLL_SWITCH_CLK_CTRL_REG, val);
|
||||
|
||||
nec_aterm_reset_common();
|
||||
|
||||
/*
|
||||
* deassert some RESET bits not handled by drivers
|
||||
@ -272,11 +284,59 @@ static inline void nec_aterm_init(void)
|
||||
* - ETH_SWITCH(_ANALOG): eth0
|
||||
* - RTC : wmac
|
||||
*/
|
||||
reg = KSEG1ADDR(AR71XX_RESET_BASE);
|
||||
val = READREG(reg + AR934X_RESET_REG_RESET_MODULE);
|
||||
val &= ~(AR934X_RESET_ETH_SWITCH | AR934X_RESET_ETH_SWITCH_ANALOG |
|
||||
AR934X_RESET_RTC);
|
||||
WRITEREG(reg + AR934X_RESET_REG_RESET_MODULE, val);
|
||||
}
|
||||
#elif defined(CONFIG_BOARD_NEC_WG1400HP)
|
||||
|
||||
#define QCA955X_GMAC_MR_AN_CONTROL_PHY_RESET_MASK BIT(15)
|
||||
#define QCA955X_GMAC_MR_AN_CONTROL_FULL_DUPLEX_MASK BIT(8)
|
||||
#define QCA955X_GMAC_MR_AN_CONTROL_SPEED_SEL1_MASK BIT(6)
|
||||
|
||||
#define QCA955X_GMAC_SGMII_CONFIG_SPEED_SHIFT 6
|
||||
#define QCA955X_GMAC_SGMII_CONFIG_SPEED_1000M 0x2
|
||||
#define QCA955X_GMAC_SGMII_CONFIG_FORCE_SPEED_MASK BIT(5)
|
||||
#define QCA955X_GMAC_SGMII_CONFIG_MODE_CTRL_SHIFT 0
|
||||
#define QCA955X_GMAC_SGMII_CONFIG_MODE_SGMII 0x2
|
||||
|
||||
static inline void nec_aterm_init(void)
|
||||
{
|
||||
unsigned int reg, val;
|
||||
int ret;
|
||||
|
||||
printf("NEC Aterm series (QCA9558)\n");
|
||||
|
||||
nec_aterm_reset_common();
|
||||
|
||||
printf("\nCalibrating SGMII\n");
|
||||
ret = extract_qca955x_sgmii_res_cal();
|
||||
if (ret >= 0)
|
||||
setup_qca955x_eth_serdes_cal(ret);
|
||||
|
||||
/* set SGMII force mode to make eth1 working */
|
||||
printf("\nConfiguring SGMII force mode\n");
|
||||
reg = KSEG1ADDR(QCA955X_GMAC_BASE);
|
||||
WRITEREG(reg + QCA955X_GMAC_REG_SGMII_CONFIG,
|
||||
QCA955X_GMAC_SGMII_CONFIG_SPEED_1000M
|
||||
<< QCA955X_GMAC_SGMII_CONFIG_SPEED_SHIFT |
|
||||
QCA955X_GMAC_SGMII_CONFIG_FORCE_SPEED_MASK |
|
||||
QCA955X_GMAC_SGMII_CONFIG_MODE_SGMII
|
||||
<< QCA955X_GMAC_SGMII_CONFIG_MODE_CTRL_SHIFT);
|
||||
printf(" SGMII_CONFIG : 0x%08x\n",
|
||||
READREG(reg + QCA955X_GMAC_REG_SGMII_CONFIG));
|
||||
val = QCA955X_GMAC_MR_AN_CONTROL_FULL_DUPLEX_MASK |
|
||||
QCA955X_GMAC_MR_AN_CONTROL_SPEED_SEL1_MASK;
|
||||
WRITEREG(reg + QCA955X_GMAC_REG_MR_AN_CONTROL,
|
||||
val | QCA955X_GMAC_MR_AN_CONTROL_PHY_RESET_MASK);
|
||||
printf(" MR_AN_CONTROL: 0x%08x\n",
|
||||
READREG(reg + QCA955X_GMAC_REG_MR_AN_CONTROL));
|
||||
WRITEREG(reg + QCA955X_GMAC_REG_MR_AN_CONTROL, val);
|
||||
printf(" MR_AN_CONTROL: 0x%08x\n",
|
||||
READREG(reg + QCA955X_GMAC_REG_MR_AN_CONTROL));
|
||||
}
|
||||
#else
|
||||
static inline void nec_aterm_init(void) {}
|
||||
#endif
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user