This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
With 6.6, all DTSes were moved to their vendor subdirectories. ARM64
DTSes already used this scheme, but 32 bit Cortex A9 did not, prior
to 6.6. Introduce a kernel version check to keep backward compatibility
with 6.1.
Suggested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
As of 6.6, all upstream DTSes are moved to their respective vendor subdir.
OpenWrt already followed this practice for ARM64, but not yet for 32 bit
ARM (Armada 37x/38x).
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
DTS paths for 32 bit ARM devices changed with 6.6, move files/ to
files-6.1 to prep for kernel 6.6 introduction.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Add pending patch fixing nandc with new kerenel due to broken convertion
to new nand API. Patch has been sent upstream and will be backported to
stable kernel if accepted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework kernel patches for new kernel. Mainly adaptation for patch
related to DTS and changes for the downstream div generalize patch that
now use determine_rate.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since with recent kernel version DTS moved to a dedicated directory,
it's required to split files to per kernel version to follow kernel
version directory structure.
Also makes use of DEVICE_DTS_DIR to target the correct DTS directory
based on the kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch fixing mtdcore with MTD OTP with a fragile detection
if Nand supports OTP. Patch has been sent upstream and will be backported
to stable kernel if accepted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework kernel patches for new kernel. Mainly adaptation for patch
related to DTS, OOB Tagger and SDHCI patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS to use reference for usb node instead of redefining
them since upstream usb node names changed from usb2/3 to usb.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since with recent kernel version DTS moved to a dedicated directory,
it's required to split files to per kernel version to follow kernel
version directory structure.
Also makes use of DEVICE_DTS_DIR to target the correct DTS directory
based on the kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh backport patches for kernel 6.1.82 with make target/linux/refresh.
Fixes: 06cdc07f8c ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 3 buttons (WPS, reset, LED on/off)
- 1 1Gbit WAN port
- 4 1Gbit LAN ports
Disassembly:
- There are four screws at the bottom: 2 under the rubber feets, 2 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes on the side of the board.
- Pins (from front to rear):
- 3.3V
- RX
- TX
- GND
- Settings: 115200, 8N1
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- The recovery web interface always flashes to the currently active partition.
- If OpenWrt is flahsed to the second partition, it will not boot.
- Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end.
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-recovery.bin
- The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt.
- If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are reuqired:
- Start the web recovery interface again and flash the **decrypted OEM image**. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1.
- Now flash the **encrypted OEM image** via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1.
- Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-initramfs-kernel.bin.
- Power on the device and select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.200.2, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M30 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware M30A1_FW101B05: ./m32-firmware-util M30 --DecryptFactoryImage M30A1_FW101B05\(0725091522\).bin M30A1_FW101B05\(0725091522\)_decrypted.bin
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Controlling the LEDs:
- The LEDs are controlled by a chip called "GCA230718" which is connected to the main CPU via I2C (address 0x40)
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Comparison to M32/R32:
- The algorithms for decrypting the OEM firmware are the same for M30/M32/R32, only the keys differ
- The keys are available in the GPL sources for the M32
- The M32/R32 contained raw data in the firmware images (kernel, rootfs), the R30 uses a sysupgrade tar instead
- Creation of the recovery image is quite similar, only the header start string changes. So mostly takeover from M32/R32 for that.
- Turned out that the bytes at offset 0x0E and 0x0F in the recovery image header are the checksum over the data area
- This checksum was not checked in the recovery web interface of M32/R32 devices, but is now active in R30
- I adapted the recovery image creation to also calculate the checksum over the data area
- The recovery image header for M30 contains addresses which don't match the memory layout in the DTS. The same addresses are also present in the OEM images
- The recovery web interface either calculates the correct addresses from it or has it's own logic to determine where which information must be written
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
The recovery image is reqired for D-Link M30 as well. So I moved it to include/image-commands.mk to be able to use it for MT7622 and filogic devices.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO
enterprise access point with two Gigabit Ethernet ports and PoE
support.
Hardware highlights:
- CPU: QCA9550 SoC at 720MHz
- RAM: 256MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: QCA9550-internal radio
- Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC
- Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY
- Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY
- PoE: input through Ethernet 1 port
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: SGM706 (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- eth1 = label MAC + 1
- radio0 (Wi-Fi 5GHz) = label MAC + 2
- radio1 (Wi-Fi 2.4GHz) = label MAC + 3
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script
"run ramboot". Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile
openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot
be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from
non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP5X30XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap5030dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues
-----------------------
- On initial power-up, the Huawei-modified bootloader suspends both
ethernet PHYs (it sets the "Power Down" bit in the MII control
register). Unfortunately, at the time of the initial port, the kernel
driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume
callback defined which would clear this bit. This makes the PHY unusable
since it remains suspended forever. This is why the backported kernel
patches in this commit are required which add this callback and for
completeness also a suspend callback.
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the CPU_CLK/4 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
[fixed 6.6 backport patch naming]
Signed-off-by: David Bauer <mail@david-bauer.net>
On x86, the build failed while trying to compile tools/lib/string.c because
of a clash with the system provided implementation for strlcpy
Add ifdefs to prevent the conflict.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This device only has 64 MiB RAM and ath10k wireless driver will
consume a lot of memory. Let's move it to the tiny sub-target to
get extra 7 MiB of free space. In this way, we can extend their
lifetime to receive support for the next OpenWrt LTS version. This
patch also trims the duplicate "recovery.bin" image as it's the
same as the "factory.bin".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
These devices only have 64 MiB RAM and ath10k wireless driver will
consume a lot of memory. Let's move them to the tiny sub-target to
get extra 7 MiB of free space. In this way, we can extend their
lifetime to receive support for the next OpenWrt LTS version. This
patch also trims the USB package for the non-existent USB port.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The upcoming D-Link devices to the tiny sub-target require it to
parse the u-env MAC address. The kernel size will increase by
about 1 KiB.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Move seama image recipe to the common Makefile in order for some
tiny sub-target D-Link devices can share it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: W632GU6NB DDR3 256MB
Ethernet: 1x 2.5G + 4x 1G
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
1. Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
2. Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-preloader.bin spi0.0"
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
3. Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download initramfs image, reboot router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Note:
1. Back up all mtd partitions before flashing.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
ttyS2 is the default console used for all rockchip boards.
The redundant 'console=tty1' parameter now breaks the console due to
recent procd update.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: e35c7ab51f ("rockchip: merge bootscript")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
6.6 has been in testing on qualcommax for a while so it should be in a
good shape, but lets default to it to get a wider audience.
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's required to support NAND controllers with WP pin on boards that
don't have it connected to NAND chip.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Key features:
Allwinner H618 SoC (Quad core Cortex-A53)
1/1.5/2/4 GiB LPDDR4 DRAM
1 USB 2.0 type C port (Power + OTG)
1 USB 2.0 host port
1Gbps Ethernet port
Micro-HDMI port
MicroSD slot
Installation:
Write the image to SD Card with dd.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Backport AXP15060, AXP313a and AXP192 support.
The AXP15060 PMIC is used for starfive boards,
and the AXP313a PMIC is used for sunxi boards.
Remove conflicting patches from starfive target.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix issue of transmitting abnormal data which leads to link problems
in 1G and 2.5G SerDes modes (SGMII, 1000Base-X, 2500Base-X) on the
MediaTek MT7988 SoC.
Link: b72d6cba92
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Zyxel GS1900-8 v2 or Rev.B1 is a newer variant of the GS1900-8, but
otherwise similar to the other GS1900 switches.
Differences
------------
* Front Button labeled RESTORE
* NO Power Switch on rear
* Serial Header next to the barrel power connector
* Part Number ends 0102F
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 8GB eMMC or 128 MB SPI-NAND
RAM: 256MB
Ethernet: 5x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
USB: M.2(B-key) for 4G/5G Module
Power: DC 12V 1A
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC RX TX GND | <= |
| ----------------- |
--------------------------
The U-boot menu will automatically appear at startup, and then select
the required options through UP/DOWN Key.
NAND Flash and eMMC Flash instructions:
1. Set your computers IP adress to 192.168.1.2.
2. Run a TFTP server providing the sysupgrade.bin image.
3. Power on the router, into the U-Boot menu.
4. Select "2. Upgrade firmware"
5. Update sysupgrade.bin file name, input server IP and input device
IP (if they deviate from the defaults)
6. Wait for automatic startup after burning
Signed-off-by: Allen Zhao <allenzhao@unielecinc.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
patch 150-arch-powerpc-simpleboot-prevent-overwrite-of-CPU1-sp.patch
was missed durring copy from 5.15 to 6.1.
This patch restore it.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Add support for Gateworks Venice imx8m family of boards:
- required kernel modules for on-board devices
- image generation
- initial network config
- sysupgrade support
The resulting compressed disk image
(bin/targets/imx/cortexa53/openwrt-imx-cortexa53-gateworks_venice-squashfs-img.gz)
can be installed on a Gateworks venice board via U-Boot:
u-boot=> tftpboot $loadaddr openwrt-imx-cortexa53-gateworks_venice-squashfs-img.gz && \
gzwrite mmc $dev $loadaddr $filesize
WARNING: this will overwrite any boot firmware on the eMMC user hardware
partition which if being used will brick your board requiring JTAG to
re-program boot firmware and recover
The compressed disk image contains the partition table and filesystems only
and that it is expected that boot firmware is installed properly on the
eMMC boot0 hardware partition. The easiest way to ensure this is to
use the Gateworks JTAG adapter/process to install the latest boot firmware
as follows from a Linux host:
wget http://dev.gateworks.com/jtag/jtag_usbv4
chmod +x jtag_usbv4
wget http://dev.gateworks.com/venice/images/firmware-venice-imx8mm.bin
sudo ./jtag_usbv4 -p firmware-venice-imx8mm.bin
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add imx8m support:
- add a cortexa53 subtarget to imx
- move ARCH and KERNELNAME to subtargets
- account for kernel modules that are not used for cortexa53
No device-specific targets or firmware images are created yet but all
imx8m* dtbs will be built.
enabling CONFIG_TARGET_ROOTFS_INITRAMFS results in
openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin which has been
successfully booted on an imx8mm-evk using the following:
u-boot=> tftpboot $fdt_addr_r image-imx8mm-evk.dtb && \
tftpboot $kernel_addr_r openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin && \
booti $kernel_addr_r - $fdt_addr_r
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a hotplug script and add ttyATH1 on ELECOM WAB-I1750-PS to
/etc/inittab while booting for using that console as an OpenWrt console.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Register ttyS0 and ttyATH1 as Linux console on ELECOM WAB-I1750-PS.
ttyS0 provides "SERVICE" port and internal pin header for debugging and
recoverying by maker, ttyATH1 provides "SERIAL" port for configuration
by users.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The 6.1 kernel has caused another increase in kernel size, and now
it's more than 3MB:
WARNING: Image file iom_ix4-200d-uImage is too big: 3170394 > 3145728
WARNING: Image file iom_ix2-200-uImage is too big: 3171494 > 3145728
WARNING: Image file linksys_e4200-v2-uImage is too big: 3171879 > 3145728
WARNING: Image file linksys_ea4500-uImage is too big: 3171871 > 3145728
WARNING: Image file linksys_ea3500-uImage is too big: 3171651 > 3145728
This causes problems for 5 devices:
- Iomega StorCenter ix2/ix4
- Linksys EA3500/EA4200/EA4500
They have enough resources for proper operation with 6.1, but all of
them had a 3MB kernel size limit. Let's keep them alive and
resize kernel partitions to 4MB.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
6.1 testing version was introduced some time ago. Kernel size issues
are resolved now. Time to bump kernel version.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
When build images with the 6.1 kernel for all devices and all kmods,
there is one dependancy error:
pkg_hash_check_unresolved: cannot find dependency kmod-thermal
for kmod-hwmon-gpiofan
This commit fix that issue.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Copied from original Andrew's Lunn commit message:
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Kirkwood Ethernet is an RGMII port. Set the
switch to impose the RGMII delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
This commit backport change from upstream and fix downstream EA3500 dts.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
TP-Link RE205 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with external antennas.
It's based on MediaTek MT7628AN+MT7610EN like the RE200 v3/v4 but with
external antennas.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 5x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)
There are 2.4G and 5G LEDs in blue which are controlled separately.
Installation
------------
Installation is identical to RE200 v3 devices as described at
https://openwrt.org/toh/tp-link/re200#installation
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
U-Boot seems to be locked on newer versions, if not it can be accessed over
the UART as described in the link above.
Signed-off-by: Steffen Loley <slo-src@web.de>
This service was unfunctional due to not having its executable bit set.
Furthermore, sysupgrade complains about the file being present in images.
Also, the tc654 driver doesn't provide pwm1_enable sysfs file, instead its
now called pwm1_mode.
Please note that the fan was always spinning. It should now turn off, when
there's enough the thermal headroom.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
D-Link DGS-1210-16 hangs when rebooting and has no support for the reset
button.
Fix both by enabling the same GPIOs for reboot and the reset button as
already used for D-Link DGS-1210-20 and D-Link DGS-1210-28.
Signed-off-by: Richard Kunze <kunze@tivano.de>
When rebasing patches on top of 6.1, a change that removed NF_TABLES
from NF_FLOW_TABLE's dependency was dropped accidentally, and iptables
flow offload module can only be built when nftables is selected.
Restore the change to fix it.
Fixes: 19a246bb65 ("generic: 6.1: manually refresh hack patches")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Installation:
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Kernel 6.6 has changed the path of WLAN devices as the soc node was updated
to include an adress as well because according to spec it needed one:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v6.6.21&id=da6aa1111a17db11367817ddc10c5a6c188cdc44
So, this will break existing configuration as device path was changed for
example:
"platform/soc/c000000.wifi" to "platform/soc@0/c000000.wifi"
"platform/soc/c000000.wifi+1" to "platform/soc@0/c000000.wifi+1"
PCIe attached devices also have their path changed, so lets add a script
that will migrate the paths based on the detected running kernel version
so returning to kernel 6.1 will work as well.
Co-developed-by: Sean Khan <datapronix@protonmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When building MT7629 with ALL_KMODS then we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot compilation.
It depends on I2C so the symbol is hidden until ALL_KMODS is used and I2C
support is available, so disable the LEDS_SMARTRG_LED symbol in 6.6 config
intentionally as is done in the 6.1 mt7629 config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Disable CONFIG_CRYPTO_SM4_ARM64_CE_CCM and CONFIG_CRYPTO_SM4_ARM64_CE_GCM
in the generic config like we do with similar CE symbols.
This avoids the need to disable them in individual targets.
Signed-off-by: Robert Marko <robimarko@gmail.com>
* have more defined PWM steps similar to the vendor's shell script doing
the same thing
* replace PWM values with experiencal values provided by forum users
* increase hyteresis to prevent changing fan speed every second
(just because it's annoying to listen to)
* add 'hot' trip point at 75 deg. to warn users that shutdown is imminent
Tested on Puzzle M902 only for now, PWM values for Puzzle M901 might be
slightly different but should quite certainly also be rised.
Suggested-by: Martin Gierschner <martin_gierschner@gmx.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The vendor u-boot knows nothing about UBI, and we used to have a
fixed-size kernel partition for vendor u-boot and UBI for rootfs.
However, that fixed partition becomes too small eventually, and
expanding it requires complicated procedure.
This commit changed the flash layout and added a second u-boot
where the kernel supposed to be.
Now the vendor u-boot chainloads our mainline u-boot, and our
u-boot reads kernel+rootfs from UBI, verifies it, and boot
into OpenWrt.
There are two possible ways to convert from the old fw:
Flash the factory image using mtd (provided by @rany2):
mount -o remount,ro /
mount -o remount,ro /overlay
cd /tmp
dd if=factory.bin bs=1M count=4 | mtd write - kernel
dd if=factory.bin bs=1M skip=4 | mtd -r write - ubi
Or, flash the 2nd u-boot via mtd and upload the firmware
to the 2nd u-boot using tftp:
1. prepare a tftp server at 192.168.1.254 to serve the
sysupgrade image:
openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-squashfs-sysupgrade.itb
2. upload the ubi-loader.itb to OpenWrt /tmp, and flash it to
the old kernel partition:
mtd -r write openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-ubi-loader.itb
3. The router should reboot and flash the sysupgrade image via TFTP.
Procedure for flashing from vendor firmware shouldn't change.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
With kernel 6.1 image size is too large for Edgerouter X current size
limit and is causing the buildbots to fail building so images for other
devices are not updated as well.
So, disable building Edgerouter X images until a workaround is found.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit e298d8a38b23 [0] changed method how to blink delays are pased
to function. Downstream commit must follow it.
[0] https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Currently, 6 MAC addresses are read from the "boarddata1" partition and set for network interfaces in sequence.
This partition only contains 3 MAC addresses:
1. lan mac
2. wan mac
3. wlan5g mac
As result only lan2, lan3 and lan4 have correct (OUI) MAC addresses.
lan1, lan5 and wan interfaces get MAC addresses with incorrect OUI from random data on "boarddata1" partition.
This commit fix this and use first MAC for lan and second MAC for wan interfaces.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
The port 5 of most ipq60xx devices is connected to qca8075,
a few are connected to qca8081. So assume that the default
connection is qca8075 and set the phy mode to psgmii.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Marvell's thermal sensors do not support interrupts, so we need to
poll them. Reading temperature every second should be enough to
control the fan.
While at it, also make sure fan speed is reduced again if temperature
goes down.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On Buffalo WXR-5590AX12, some LEDs don't have "function" property and
only "color" property is available for the newer binding of LED on
Linux Kernel.
2e659930d3 ("qualcommax: drop redundant label with new LED
color/function format") removes "label" property from LEDs, then,
multiple "<color>:" (ex.: "white:"/"red:") will be appeared as LED names
and renamed to "<color>:_<num>" ("ex.: "white:_1", "green:_2", ...) by
kernel.
logs:
[ 5.372863] leds-gpio leds: Led white: renamed to white:_1 due to name collision
[ 5.375796] leds-gpio leds: Led red: renamed to red:_1 due to name collision
/sys/class/leds:
root@OpenWrt:/# ls /sys/class/leds/
red: red:power white: white:power
red:_1 red:wlan white:_1 white:wlan
Fix this issue by adding missing "function" property to LEDs on Buffalo
WXR-5950AX12.
Note: there are no appropriate functions in dt-bindings/leds/common.h
for some LEDs, so use the hardcoded strings for them instead.
Fixes: 2e659930d3 ("qualcommax: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
On QNAP QHora-301W, all LEDs don't have "function" property and only
"color" property is available for the newer binding of LED on Linux
Kernel.
2e659930d3 ("qualcommax: drop redundant label with new LED
color/function format") removes "label" property from LEDs, then,
multiple "<color>:" (ex.: "amber:"/"green:"/"red:") will be appeared as
LED names and renamed to "<color>:_<num>" ("ex.: "green:_1", "green:_2",
...) by kernel.
logs:
[ 4.246494] leds-gpio leds: Led green: renamed to green:_1 due to name collision
[ 4.248978] leds-gpio leds: Led green: renamed to green:_2 due to name collision
[ 4.256345] leds-gpio leds: Led green: renamed to green:_3 due to name collision
[ 4.263770] leds-gpio leds: Led green: renamed to green:_4 due to name collision
[ 4.271105] leds-gpio leds: Led amber: renamed to amber:_1 due to name collision
[ 4.278487] leds-gpio leds: Led green: renamed to green:_5 due to name collision
[ 4.285856] leds-gpio leds: Led amber: renamed to amber:_2 due to name collision
[ 4.293257] leds-gpio leds: Led green: renamed to green:_6 due to name collision
[ 4.300616] leds-gpio leds: Led amber: renamed to amber:_3 due to name collision
[ 4.308002] leds-gpio leds: Led green: renamed to green:_7 due to name collision
[ 4.315384] leds-gpio leds: Led amber: renamed to amber:_4 due to name collision
[ 4.322760] leds-gpio leds: Led green: renamed to green:_8 due to name collision
[ 4.330135] leds-gpio leds: Led amber: renamed to amber:_5 due to name collision
/sys/class/leds:
amber: amber:_4 green:_2 green:_6
amber:_1 green:_5 green:_3 green:_7
amber:_2 green: green:_4 green:_8
amber:_3 green:_1 green:_5 red:
Fix this issue by adding missing "function" (and "function-enumerator")
property to LEDs on QNAP QHora-301W.
Note: there are no appropriate functions in dt-bindings/leds/common.h
for some LEDs, so use the hardcoded strings for them instead.
Fixes: 2e659930d3 ("qualcommax: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is needed recommended.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6281 @1GHz
- 128Mb RAM
- 256Mb NAND
- 1x GbE LAN (Marvell 88E1116)
- 1x USB 2.0
- 2x SATA
- PCF8563 RTC
- LM75 sensor
- TC654 PWM fan controller
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b ./u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 netgear_stora-u-boot.kwb
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-netgear_stora-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
The fan is controlled in 3 stages by a script running every minute
from cron, measuring the CPU temperature.
Snippets taken from bodhi <mibodhi@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The dir variable has been used uninitialized since the port to 5.10, and
somehow this remains undetected by GCC.
Fixes: b10d604459 ("kernel: add linux 5.10 support")
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Most mt7622 devices use the mt7531 switch, which have been
switched to dsa driver for a long time. So use dsa as the
default configuration and configure these rtl8367s devices
separately. This reduces the amount of code.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
In kernel 6.6, dts files for mediatek arm target are moved into
arch/arm/boot/dts/mediatek instead of legacy path arch/arm/boot/dts.
To avoid dts compile failure, change DTS_DIR to the mediatek subfolder
for kernel 6.6.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Also backport most recent MHI modem additions to Linux 6.6.
Adds support for generic SDX75-based modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing CLK_TOP_PEXTP_Px_SEL clock for each of the 4 PCIe interfaces
of the MT7988 SoC. Without that clock PCIe doesn't work reliable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CONFIG_NET_VENDOR_DAVICOM is needed to activate the CONFIG_DM9000 option
which builds the kmod-dm9000. This fixes the following warning:
logs/package/kernel/linux/compile.txt:WARNING: kmod-dm9000 is not available in the kernel config - generating empty package
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Many can kernel modules are now gated by the newly introduced
CONFIG_CAN_NETLINK configuration option. Activate it to build the can
drivers again.
This was changed in this upstream Linux commit:
https://git.kernel.org/linus/df6ad5dd838e0fa543ca28ca6154901fa65a9443
This should fix these warnings with kernel 6.1 and 6.6:
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can-pci is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can-platform is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-mcp251x is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-slcan is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-8dev is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-ems is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-kvaser is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-peak is not available in the kernel config - generating empty package
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove the remaining configuration entries that were omitted in the
previous commit.
Fixes: 1576474f55 ("ramips: switch to 6.1 kernel")
Signed-off-by: Nick Hainke <vincent@systemli.org>
The GL.iNet X3000 and XE3000 are Wi-Fi 6 5G cellular routers, based on
MediaTek MT7981A SoC. The XE3000 is the same device as the X3000,
except for an additional battery.
Specifications:
- SoC: Filogic 820 MT7981A (1.3GHz)
- RAM: DDR4 512M
- Flash: eMMC 8G, MicroSD card slot
- WiFi: 2.4GHz and 5GHz with 6 antennas
- Ethernet:
- 1x LAN (10/100/1000M)
- 1x WAN (10/100/1000/2500M)
- 5G: Quectel RM520N-GL with two nano-SIM card slots
- USB: 1x USB 2.0 port
- UART:
- 3.3V, TX, RX, GND / 115200 8N1
MAC addresses as verified by OEM firmware:
vendor OpenWrt address source
WAN eth0 label factory 0x0a (label)
LAN eth1 label + 1
2g phy0-ap0 label + 2 factory 0x04
5g phy1-ap0 label + 3
Installation via U-Boot rescue:
1. Press and hold reset button while booting the device
2. Wait for the Internet led to blink 5 times
3. Release reset button
4. The rescue page is accessible via http://192.168.1.1
5. Select the OpenWrt sysupgrade image and start upgrade
6. Wait for the router to flash new firmware and reboot
Revert to stock firmware:
1. Download the stock firmware from GL.iNet website
2. Use the method explained above to flash the stock firmware
Switch the modem network port between PCIe and USB interfaces:
1. Connect to the AT commands (/dev/ttyUSB2) port using
e.g. minicom: minicom -D /dev/ttyUSB2
2. Check the current modem mode with 'AT+QCFG="data_interface"':
- 0,0 indicates that the network port uses the USB interface
- 1,0 indicates that the network port uses the PCIe interface
3. Switch the active interface with:
- 'AT+QCFG="data_interface",0,0' to use the USB interface
- 'AT+QCFG="data_interface",1,0' to use the PCIe interface
4. Reboot
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Add new emmc groups in the pinctrl driver for the
MediaTek MT7981 SoC:
* emmc reset, with pin 15.
* emmc 4-bit bus-width, with pins 16 to 19, and 24 to 25.
* emmc 8-bit bus-width, with pins 16 to 25.
The existing emmc_45 group is kept for legacy reasons, even
if this is the union of emmc_reset and emmc_8 groups.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Reference: b40da332df
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport commit faa5f17fe2 ("kernel: mtk_eth_soc: release
MAC_MCR_FORCE_LINK only when MAC is up") to Linux 5.15 as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The 5.15 kenel config file, patches and version switches will be
removed in this patch. We will introduce kernel 6.6 support soon.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This commit adds support for Z-ROUTER ZR-2660 (also known as Routerich
AX1800) wireless WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (AMD/Spansion S34ML01G2)
- WLAN :
- 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2
- 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- USB : 1x 2.0
- UART : 3.3V, 115200n8, pins are silkscreened on the pcb
- Buttons : 1x Reset
- LEDs : 1x WiFi 2.4 GHz (green)
1x WiFi 5 GHz (green)
1x LAN (green)
1x WAN (green)
1x WAN no-internet (red)
- Power : 12 VDC, 1 A
Installation
------------
1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs
image (initramfs.bin) to the tftp root dir
2. Open the following link in the browser to enable telnet:
http://192.168.2.1/cgi-bin/telnet_ssh
3. Connect to the router (default IP: 192.168.2.1) using telnet shell
(credentials - user:admin)
4. Run the following commands in the telnet shell (this will install
OpenWrt initramfs image on nand flash):
cd /tmp
tftp -g -r initramfs.bin 192.168.2.2
mtd write initramfs.bin firmware
mtd erase firmware_backup
reboot
5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the
router
6. Connect to the router (IP: 192.168.1.1) using ssh shell and run
sysupgrade command:
sysupgrade -n /tmp/sysupgrade.bin
Return to stock
---------------
1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp
2. Run following command in the router shell:
cd /tmp
mtd write stock.bin firmware
reboot
Recovery
--------
Connect uart (pins are silkscreened on the pcb), interrupt boot process by
pressing any key, use u-boot menu to flash stock firmware image or OpenWrt
initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 24:0f:5e:xx:xx:4c | label |
| WAN | 24:0f:5e:xx:xx:4d | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 |
+---------+-------------------+-----------+
The WLAN 2.4 MAC was found in 'factory', 0x4
The LAN MAC was found in 'factory', 0xfff4
The WAN MAC was found in 'factory', 0xfffa
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
When kernel 6.6 is being compiled with GCC13 it will prompt for:
Compressed Debug information
> 1. Don't compress debug information (DEBUG_INFO_COMPRESSED_NONE)
2. Compress debugging information with zlib (DEBUG_INFO_COMPRESSED_ZLIB)
3. Compress debugging information with zstd (DEBUG_INFO_COMPRESSED_ZSTD) (NEW)
This is because kernel now also has support for compressing debug info
with ZSTD, so add the missing symbol and disable it by default.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The YunCore G720 is a dual band 802.11ax router with 5 GbE ports.
Specs:
- SoC: MediaTek MT7621
- Ethernet: 5x GbE ports (built-in MT7530)
- Wireless 2.4GHz / 5GHz: MediaTek MT7915E
- RAM: 256MiB
- ROM: 16MiB (W25Q128)
- 1 Button (reset)
- 8 LEDs (1x system, 2x wifi, 5x switch ports)
Flash instructions:
The vendor firmware is based on OpenWrt, the sysupgrade image can be
flashed using the '-F' (force) option on the CLI.
Make sure not to keep settings when doing so.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
We have had the testing kernel for several weeks now. Let's switch to 6.1
to have more testers. Additionally, 6.6 is already in the pipeline.
Signed-off-by: Nick Hainke <vincent@systemli.org>
CONFIG_HID_SUPPORT:
Set default value for kmod-hid
CONFIG_USB_CDNS3_IMX:
CONFIG_USB_CDNS3_PCI_WRAP:
CONFIG_USB_CDNSP_PCI:
Introduced by db0d7cf6a1 (usb: add cdns3 support)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This reverts commit 7ea82bc17d.
This commit does not meet formal requirments, and has been merged due to
my error.
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_DEBUG_INFO_COMPRESSED_ZSTD, required by GCC 13.0+
Compress the debug information using zstd. This may provide better compression than zlib, for about the same time costs, but requires newer toolchain support. Requires GCC 13.0+ or Clang 16.0+, binutils 2.40+, and zstd.
Signed-off-by: CharlesMengCA <58993776+CharlesMengCA@users.noreply.github.com>
As shared remove functions now returns void instead of int we need to
use .remove_new instead of .remove.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A new patch was added meanwhile which will go as fix via netdev tree.
Copy & refresh it for Linux 6.6 as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Avoid crashing the kernel when trying to detect early versions of
RealTek RTL8221B 2.5G Ethernet PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, the existing uncompressed kallsym support is causing qualcommax
boards to hang on boot, and only after earlycon and verbose BUG() prints
are enabled the trace is visible:
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] kernel BUG at kernel/kallsyms.c:340!
[ 0.000000] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
Felix has fixed up the uncompressed kallsyms support so modify the current
patch with the fix.
All credits for the code go to Felix.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update fitblk driver which has previously been backported to Linux 6.1
so it can build and work with Linux 6.6.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing symbols to config for 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Due to what seems to be an undocumented oddity in MediaTek's MT7988
SoC design the CLK_INFRA_PCIE_PERI_26M_CK_P2 clock requires
CLK_INFRA_PCIE_PERI_26M_CK_P3 to be enabled.
This currently leads to PCIe port 2 not working in Linux.
Reflect the apparent relationship in the clk driver to make sure PCIe
port 2 of the MT7988 SoC works.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Clearing bit MAC_MCR_FORCE_LINK which forces the link down too early
can result in MAC ending up in a broken/blocked state.
Fix this by handling this bit in the .mac_link_up and .mac_link_down
calls instead of in .mac_finish.
Suggested-by: Mason-cw Chang <Mason-cw.Chang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 16MB SPI NOR W25Q128WFG
- RAM: 128MB DDR3 W631GG6KB-15
- Ethernet: 1x 1000M, 3x 100M
- Wifi: BCM435F
- 1x USB 2.0 port
- 3x Button
- 12x LED
Flashing via serial
- Connect to the 3.3V TTL UART on the board
(J6 pinout Vcc Rx Tx Gnd) at 115200-8-N-1
- Press any key in the serial console when powering up the board to enter
the CFE prompt
- Configure an interface on your workstation to static IP 192.168.1.100
and connect it to the board
- Start a TFTP server with the firmware image
- On the CFE prompt, enter the command
"f 192.168.1.100:openwrt-bmips-bcm63268-smartrg_sr505n-squashfs-cfe.bin"
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Remove unneeded LED labels]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
CDNS3 is a SuperSpeed (SS) USB 3.0 Dual-Role-Device (DRD) controller from
Cadence. Add support for this device, and add the required symbols into
the generic configs.
Compile-tested: apm821xx, bcm4908, imx, mpc85xx, pistachio, starfive
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* Increase flash SPI frequency to 50MHz
The maximum SPI frequency of MX25L6406EM2I is 86 MHz,
but in this patch 50 MHz was chosen as a safe value.
* Update Ethernet MAC addresses
Till now LAN/WAN MAC addresses were flipped
compared to stock firmware.
* Fix Wi-Fi LEDs by adding mt76 led nodes
* Fix LAN port order
LAN ports are in reverse order of switch ports.
* Fix the well-known "LZMA ERROR 1" error by using lzma-loader
* Set uImage name, which enables installation via stock web interface:
1. Upload **initramfs** image file to the web page.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Unlike the recovery image, this initramfs-factory image can be flashed
using the stock firmware web interface (from any active boot partition),
as well as the bootloader recovery web page. Drop the recovery image in
favor of the factory image.
Installation via stock/recovery web interface:
1. Flash **initramfs-factory** image through the web page.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The "0x80001000" address logically comes from "loadaddr-y" variable for
mt7621 subtarget. Let's replace the hardcoded value with the predefined
variable. This change is purely cosmetic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Contrary to common ipTIME NOR devices, the "Config" partition of T5004
and AX2004M contain normal U-Boot environment variables. Renaming the
partition into "u-boot-env" serves for better description, and it also
conforms to common naming practice in OpenWrt.
This patch might also be extended to A3004T, but its u-boot-env
partition layout has not been confirmed yet.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
AX2004M uses NMBM on its NAND flash, but it was not enabled in DTS as the
device support [1] had been added before NMBM feature in mtk_bmt driver [2].
Let's enable it now.
With this change, there is a low possibility of boot failure after
sysupgrade from older versions. As AX2004M already has gone through
two stable releases in the meantime, it would be safe to warn users
by bumping DEVICE_COMPAT_VERSION.
[1] 37753f34ac ("ramips: add support for ipTIME AX2004M")
[2] 06382d1af7 ("kernel: add support for mediatek NMBM flash mapping support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The COVR-C1200 devices are sold as "Whole Home Mesh Wi-Fi"
sets in packs of two (COVR-C1202) and three (COVR-C1203).
Specifications:
* QCA9563, 16 MiB flash, 128 MiB RAM, 2x3:2 802.11n
* QCA9886 2x2:2 801.11ac Wave 2
* AR8337, 2 Gigabit ports (1: WAN; 2: LAN)
* USB Type-C power connector (5V, 3A)
Installation COVR Point A:
* In factory reset state: OEM Web UI is at 192.168.0.50
no DHCP, skip wizard by directly accessing:
http://192.168.0.50/UpdateFirmware_Simple.html
* After completing setup wizard: Web UI is at 192.168.0.1
DHCP enabled, login with empty password
* Flash factory.bin
* Perform a factory reset to restore OpenWrt UCI defaults
Installation COVR Points B:
* OEM Web UI is at 192.168.0.50, no DHCP, empty password
* Flash factory.bin
* Perform a factory reset to restore OpenWrt UCI defaults
Recovery:
* Keep reset button pressed during power on
* Recovery Web UI is at 192.168.0.50, no DHCP
* Flash factory.bin
used to work best with Chromium-based browsers or curl:
curl -F firmware=@factory.bin \
http://192.168.0.50/upgrade.cgi
since this fails to work on modern Linux systems,
there is also a script dlink_recovery_upload.py
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Include a statement about having to run the installer in the
sysupgrade compat warning for the Linksys E8450 (UBI).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Probing of the fitblk driver in some situations happens after the kernel
attempts to mount rootfs, which then fails.
Always use 'rootwait' when using fitblk for rootfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cleanup uart1-related node on ELECOM WAB-I1750-PS and enable it for
"SERIAL" port on the case.
"SERIAL" port can be used for OpenWrt console by adding the following
line to /etc/inittab and rebooting:
ttyATH1::askfirst:/usr/libexec/login.sh
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add aliases with "serialN = &uartN;" of uart0/1 on QCA955x SoCs to
qca955x.dtsi, to enable uart1 on Linux Kernel.
without this:
[ 0.342915] ar933x-uart 18500000.uart: unable to get alias id, err=-19
Additionally, remove "serial0 = &uart;" alias from QCA955x device
dts/dtsi files.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add HighSpeed UART support to QCA955x series SoCs as a secondary UART
(uart1). This UART is compatible with qca,ar9330-uart.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Rename the DT label of the primary UART on Qualcomm Atheros QCA955x
series SoCs to "uart0" from "uart" for the preparation to add HighSpeed
UART (uart1) support.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
with 6.1, the kernel no longer fitted into the 16 MiB and
kicking down the can and increasing KERNEL_SIZE to 20 MiB
didn't help as the device failed to boot.
Using 'kernel-bin | gzip | uimage gzip' didn't work since the
uboot does not have enough heap to decompress these big kernels.
And finally playing around with uboot was more a hassle than
converting this device to take the simpleImage-boot-route in
the future.
Note: The device now takes even longer on the first boot-up after
the flash due to JFFS2 initializing all the remaining flash.
Be prepared to wait up to 10 minutes before the green status LED
stops blinking and will shine a solid green!
(On the plus site: the device now has ~10 MiB of additional
space for rootfs+rootfs_data).
Note2: This patch includes a kernel patch refresh.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kernel and initramfs size grows. Now uncompressed initramfs image and
regular kernel image overlaps configured area:
Initramfs:
WRAP arch/powerpc/boot/simpleImage.br200-wp
INFO: Uncompressed kernel (size 0x1428688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1500000)
WRAP arch/powerpc/boot/simpleImage.tl-wdr4900-v1
INFO: Uncompressed kernel (size 0x1428688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1500000)
WRAP arch/powerpc/boot/simpleImage.ws-ap3715i
INFO: Uncompressed kernel (size 0x1428688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1500000)
Regular image:
WRAP arch/powerpc/boot/simpleImage.br200-wp
INFO: Uncompressed kernel (size 0x10e0688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1100000)
WRAP arch/powerpc/boot/simpleImage.tl-wdr4900-v1
INFO: Uncompressed kernel (size 0x10e0688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1100000)
WRAP arch/powerpc/boot/simpleImage.ws-ap3715i
INFO: Uncompressed kernel (size 0x10e0688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1100000)
Let's change wrapper address to safe value.
Tested on: TL-WDR4900, BR200-WP
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch replaces 'of_flat_dt_is_compatible' with 'of_machine_is_compatible'.
The TL-WDR4900 platform file won't compile in the 6.1 kernel. The platform
files for the rest of the routers have been reworked or based on newer
solutions.
Let's make the TL-WDR4900 consistent with them.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This fixes the following compile problem:
````
CC arch/mips/kernel/vpe-mt.o
arch/mips/kernel/vpe-mt.c: In function 'vpe_run':
arch/mips/kernel/vpe-mt.c:32:23: error: unused variable 'physical_memsize' [-Werror=unused-variable]
32 | unsigned long physical_memsize = 0L;
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:289: arch/mips/kernel/vpe-mt.o] Error 1
````
physical_memsize was removed from upstream kernel, see:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=5b4f6c5ff65c8551018ccea40c569afd759734c0
Fixes: 387fde0da0 ("kernel: bump 5.15 to 5.15.150")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 2d63d42f5e ("mediatek: convert to new LED color/function
format where possible") leaves Xiaomi Redmi AX6000 un-converted,
the two LEDs become dead.
Now, LEDs are alive again.
Fixes: 2d63d42f5e ("mediatek: convert to new LED color/function
format where possible")
Signed-off-by: Furong Xu <xfr@outlook.com>
ath25 has been on life support for the last couple of releases, eventually
leading to marking it as source-only in 2023.
It has been basically only touched to do a kernel bump so that we can make
the new OpenWrt release which was a challenge due to small RAM amount.
However, with the attempt of kernel 6.1 update it turns out that kernel
cannot even finish booting due to RAM constraints, so its time to let this
target go.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX214 is a 802.11 ax dual-band AP
with PoE. (similar to Engenius EWS357APV3)
Specifications:
• CPU: Qualcomm IPQ6010 Quad core Cortex-A53
• RAM: 512MB of DDR3
• Storage: 128MB NAND (Macronix MX30UF1G18AC)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WIFI:
2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
4 x GPIO-controlled LEDs
- 1 Power LED (orange)
- 1 LAN LED (blue)
- 1 WIFI 5g LED (blue)
- 1 WIFI 2g LED (blue)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An populated serial header is onboard, format is
1.25mm 4p (DF13A-4P-1.25H)
RX/TX is working, bootwait is active, secure boot is not
enabled.
The root password of the stock firmware is unknown,
but failsafe mode can be entered to reset the password.
Installation Instructions:
- obtain serial access
- stop auto boot (press "4", Entr boot command line
interface)
- setenv active_fw 0 (to boot from the primary rootfs,
or set to 1 to boot from the secondary rootfs
partition)
- saveenv
- tftpboot the initramfs image
- bootm
- copy
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
to the device
- write the image to the NAND:
- cat /proc/mtd and look for rootfs partition (should
be mtd11,
or mtd12 if you choose active_fw 1)
- ubiformat /dev/mtd11 -f -y
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
- reboot
Note: the firmware is senao-based. But I was unable to build
a valid senao-header into the image.
Maybe they changed the header format and senaoFW isn't
working any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
BCM63xx maintainance is a PITA since there's no full Device Tree support and
therefore every board needs it's own definition in board_bcm963xx.c
There's no DSA support for this board and there have been very few
contributions in the last years.
Moreover, BCM63xx SoCs >= BCM6358 are already supported in bmips target, so
any efforts to keep this target alive aren't worth the time.
Let's focus the community efforts on improving bmips instead.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The SolidRun ClearFog Pro is a router based on the SolidRun CN9130 SOM.
Specs:
- SoC: Quad-Core Cortex-A72 CN9130 SoC
- RAM: 4GiB DDR4
- Serial: Micro-USB port on front (FT232R, 115200 8n1)
- Storage: 8GiB eMMC, microSD card slot, 8MiB SPI NOR flash
- Ethernet: 7x GbE (1 port dedicated on SoC, 6 port switch with single GbE CPU port)
- SFP: 1x SFP+
- USB: 1x USB-A 3.1 Gen 1
- PCIe: 2x mini PCIe (one slot with USB and SIM card socket)
- SATA: 1x M.2 Key-B
In addition to the usual connectivity options this device also features
an internal mikroBUS expansion connector.
SATA is currently untested due to lack of a suitable M.2 SSD.
Installation
============
1. Write sdcard sysupgrade image to microSD card using dd or similar
2. Insert microSD card into router and apply power
3. Device boots into OpenWRT
4. (optional) dd sysupgrade image to /dev/mmcblk0 to install to eMMC
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
Upstream a patch adding support for cpufreq on AP807-based SoC like the
CN913x was submitted. Include it in patches to ensure best performance
under load and lowest power consumption in idle.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
ELECOM WAB-I1750-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 3T3R
- 2.4 GHz : Qualcomm Atheros QCA9558 (SoC)
- 5 GHz : Qualcomm Atheros QCA9880
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 2x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- "SERIAL" : RS232C (+-12V)
- port : ?
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- settings : 115200n8
- note : compatible with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1.04 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.26 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-I1750-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- "SERIAL" port is provided by HS UART on QCA9558 SoC that has
compatibility with qca,ar9330-uart, but QCA955x SoC's is not supported
on Linux Kernel and OpenWrt.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): 00:90:FE:xx:xx:0A (Config, ethaddr (text))
2.4GHz : 00:90:FE:xx:xx:0A (Config, ethaddr (text))
5GHz : 00:90:FE:xx:xx:0B
[original work]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[update for NVMEM and others]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9557.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S1167-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S600-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): 00:90:FE:xx:xx:04 (Config, ethaddr (text))
2.4GHz : 00:90:FE:xx:xx:04 (Config, ethaddr (text))
5GHz : 00:90:FE:xx:xx:05
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
ELECOM WAB-S600-PS is a 2.4/5 GHz band 11n (Wi-Fi 4) access point, based
on QCA9557.
This device also supports 11ac (Wi-Fi 5) with the another official
firmware.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S600-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S1167-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
2.4GHz : BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
5GHz : BC:5C:4C:xx:xx:7D
[original work of common dtsi part for WAB-I1750-PS]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[adding support for WAB-S600-PS]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The original commit had an invalid setting of the
led status for this device.
There is no gpio pin connected to that led so lets
remove these from the u7621-01 dtsi file.
Signed-off-by: David Bentham <db260179@gmail.com>
Update the default network configuration for Gateworks Newport boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge:
- gw610x/gw6903; single NIC: eth0
- gw620x/gw630x; two NIC's from left to right are: eth1 eth0
- gw640x; multiple NIC's from left to right: eth4 eth0 eth1 eth2 eth3
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
it is possible to boot and run OpenWrt from an image on an USB-Stick
on the MyBook Live DUO. (No, the MyBook Live Single does NOT have an
USB-Port and attempts at enabling it sadly all failed... so far).
To do that:
First, prepare a USB-Stick by writing the raw and uncompressed OpenWRT
factory image for the device onto the stick (i.e.
# gunzip -c openwrt-*wd_mybooklive*-factory.img.gz > /dev/sd$XX).
Then enter the u-boot via an attached TTL/CMOS 3.3V cable adapter and
give the following commands a try in the:
usb start; sata init
ext2load usb 0:1 ${fdt_addr_r} /boot/apollo3g.dtb
ext2load usb 0:1 ${kernel_addr_r} /boot/uImage
setenv bootargs 'root=/dev/sdc2 rw rootfstype=squashfs,ext4 rootdelay=5'
run addtty; bootm ${kernel_addr_r} - ${fdt_addr_r}
Notes:
- booting from USB-Sticks takes a long time! Be prepared to wait a few
minutes. (~3 minutes for 4 MiB /boot/uImage file on a USB 2.0 Stick)
- the bootargs part 'root=/dev/sdX2' depends on how many HDDs/SSDs are
slotted in. (if none: then use sda, if one: sdb. if two: sdc)
- rootdelay is important as the storage on the USB-Sticks do not show
up fast enough. 5 seconds might be excessive though.
- it's possible to concat these commands together in one line and
write it into u-boot's "bootcmd" environment variable and save the
environment to make the device to always boot from USB from then on.
if you have accidentally overridden the 'bootcmd' and want to return
to 'spec' enter the following commands :
setenv bootcmd 'run boot_sata_script_ap2nc'
saveenv
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Note about the MyBook Live.
The MyBook Live didn't have the encompassing fixed-partitions.
This is needed for the u-boot,env compatible to be read as otherwise
the kernel assumes this is a legacy NOR/NAND node and this binding
is unsupported.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Enable DEBUG_BUGVERBOSE by default on qualcommax as without it once BUG()
is called we will not get any output other than
"------------[ cut here ]------------"
which is not usefull at all, so since we dont have kernel size constraints
lets enable it by default.
Signed-off-by: Robert Marko <robimarko@gmail.com>
