openwrt/target/linux/mediatek/dts
Leon M. Busch-George 74df6ce9db mediatek: filogic: add support for Cudy M3000 v1
Hardware:
  SoC:     MT7981b
  RAM:     256 MB
  Flash:   128 MB SPI NAND
  Ethernet:
    1x 2.5Gbps (rtl8221b)
    1x 1Gbps (integrated phy)
  WiFi:    2x2 MT7981
  Buttons: Reset, WPS
  LED:     1x multicolor

Solder on UART:
  - remove rubber ring on the bottom
  - remove screws
  - pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
  - remove the (3) screws holding the board in the frame
  - remove the board from the frame to get to the screws for the silver, flat heat shield
  - remove the (3) screws holding the heat shield
  - solder UART pins to the back of the board
    - make sure to have the pins point out on side with the black, finned heat spread
    - the markings for the pins are going to be below the silver heat shield
    - Vcc is not needed

If you don't intend on using the UART outside of the installation process, you might not
want to solder:

  - carefully scrape off the thin layer of epoxy on the holes (not the copper)
  - place your pin header with the UART attached in the holes
  - the pins, starting with the one closest to the socket:
    - Vcc (not required)
    - GND
    - RX
    - TX
  - either wedge the header or hold it with your fingers so that the pins stay in contact with the board

Installation (UART):
  - attach an Ethernet cable to the 1Gbps port (black) on the router
  - hold the reset button while powering the router
  - press CTRL-C or wait for the timeout to get to the U-Boot prompt
  - prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
  - use 'tftpboot' in the U-Boot shell to pull the image
  - boot the image using 'bootm'
  - push the ..-sysupgrade to the router using your preferred method
  - perform the upgrade with 'sysupgrade -n'

There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit 20e4a18feb)
2024-07-15 16:12:33 +02:00
..
mt7622-buffalo-wsr-2533dhp2.dts mediatek: separate dts/dtsi for Buffalo WSR series 2024-02-27 17:42:30 +00:00
mt7622-buffalo-wsr-3200ax4s.dts mediatek: add support for Buffalo WSR-3200AX4S 2024-02-27 17:42:30 +00:00
mt7622-buffalo-wsr.dtsi mediatek: separate dts/dtsi for Buffalo WSR series 2024-02-27 17:42:30 +00:00
mt7622-dlink-eagle-pro-ai-ax3200-a1.dtsi mediatek: Add support for D-Link EAGLE PRO AI R32 2024-07-06 18:32:57 +02:00
mt7622-dlink-eagle-pro-ai-m32-a1.dts mediatek: Add support for D-Link EAGLE PRO AI R32 2024-07-06 18:32:57 +02:00
mt7622-dlink-eagle-pro-ai-r32-a1.dts mediatek: Add support for D-Link EAGLE PRO AI R32 2024-07-06 18:32:57 +02:00
mt7622-elecom-wrc-2533gent.dts mediatek: add an upstreamed spi-nand driver 2022-04-28 18:06:00 +08:00
mt7622-elecom-wrc-x3200gst3.dts treewide: remove label = "cpu" from DSA dt-binding 2023-02-26 22:22:48 +01:00
mt7622-linksys-e8450-ubi.dts mediatek: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
mt7622-linksys-e8450.dts mediatek: convert mtd-mac-address to nvmem implementation 2021-07-19 14:51:22 +02:00
mt7622-linksys-e8450.dtsi mediatek: mt7622: linksys-e8450: set driving strength for SPI-NAND 2024-03-20 16:32:25 +00:00
mt7622-netgear-wax206.dts mediatek: no longer hard-code WAN PHY of Netgear WAX206 2023-04-30 17:27:00 +01:00
mt7622-reyee-ax3200-e5.dts mediatek: also move &slot0 from dtsi down to board dts 2022-12-07 01:45:14 +00:00
mt7622-rfb1-ubi.dts mediatek: add an upstreamed spi-nand driver 2022-04-28 18:06:00 +08:00
mt7622-ruijie-rg-ew3200.dtsi treewide: remove label = "cpu" from DSA dt-binding 2023-02-26 22:22:48 +01:00
mt7622-ruijie-rg-ew3200gx-pro.dts mediatek: also move &slot0 from dtsi down to board dts 2022-12-07 01:45:14 +00:00
mt7622-totolink-a8000ru.dts mediatek: mt7622: add missing vbus regulator node to totolink-a8000ru dts 2022-07-07 00:22:23 +01:00
mt7622-ubnt-unifi-6-lr-v1-ubootmod.dts mediatek: mt7622: fix DTS compatible of UniFi 6 LR variants 2022-09-03 02:27:59 +01:00
mt7622-ubnt-unifi-6-lr-v1.dts mediatek: mt7622: fix DTS compatible of UniFi 6 LR variants 2022-09-03 02:27:59 +01:00
mt7622-ubnt-unifi-6-lr-v1.dtsi mediatek: add support for Ubiquiti UniFi 6 LR v3 2023-09-04 23:00:34 +01:00
mt7622-ubnt-unifi-6-lr-v2-ubootmod.dts mediatek: mt7622: fix DTS compatible of UniFi 6 LR variants 2022-09-03 02:27:59 +01:00
mt7622-ubnt-unifi-6-lr-v2.dts mediatek: add Ubiquiti UniFi 6 LR v2 targets 2022-06-11 19:51:33 +01:00
mt7622-ubnt-unifi-6-lr-v2.dtsi mediatek: add support for Ubiquiti UniFi 6 LR v3 2023-09-04 23:00:34 +01:00
mt7622-ubnt-unifi-6-lr-v3-ubootmod.dts mediatek: add support for Ubiquiti UniFi 6 LR v3 2023-09-04 23:00:34 +01:00
mt7622-ubnt-unifi-6-lr-v3.dts mediatek: add support for Ubiquiti UniFi 6 LR v3 2023-09-04 23:00:34 +01:00
mt7622-ubnt-unifi-6-lr-v3.dtsi mediatek: add support for Ubiquiti UniFi 6 LR v3 2023-09-04 23:00:34 +01:00
mt7622-ubnt-unifi-6-lr.dtsi mediatek: add support for Ubiquiti UniFi 6 LR v3 2023-09-04 23:00:34 +01:00
mt7622-xiaomi-redmi-router-ax6s.dts treewide: remove label = "cpu" from DSA dt-binding 2023-02-26 22:22:48 +01:00
mt7623a-unielec-u7623-02-emmc-512m.dts mediatek: u7623-02: enable early console also in legacy image 2022-01-31 00:10:38 +00:00
mt7623a-unielec-u7623-02.dts mediatek: mt7623: rework images for U7623-02 board 2022-01-23 20:20:37 +00:00
mt7623a-unielec-u7623-02.dtsi treewide: remove label = "cpu" from DSA dt-binding 2023-02-26 22:22:48 +01:00
mt7629-iptime-a6004mx.dts treewide: remove label = "cpu" from DSA dt-binding 2023-02-26 22:22:48 +01:00
mt7629-netgear-ex6250-v2.dts mediatek: add support for Netgear EX6250v2 series 2023-07-13 12:05:28 +01:00
mt7629-tplink_eap225-v5.dts mediatek: Add support for TP-Link EAP225v5 2024-02-27 17:42:30 +00:00
mt7981a-comfast-cf-e393ax.dts mediatek: add Comfast CF-E393AX support 2024-07-04 15:54:27 +02:00
mt7981a-ubnt-unifi-6-plus.dts mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+) 2023-12-07 09:45:33 +01:00
mt7981b-cetron-ct3003.dts mediatek: Cetron CT3003: fixes typo for spi properties 2024-02-27 17:42:30 +00:00
mt7981b-cmcc-rax3000m-emmc.dtso mediatek: add CMCC RAX3000M support 2023-11-07 00:46:00 +01:00
mt7981b-cmcc-rax3000m-nand.dtso mediatek: add CMCC RAX3000M support 2023-11-07 00:46:00 +01:00
mt7981b-cmcc-rax3000m.dts mediatek: fiilogic: device tree switch@1f fix 2023-12-12 09:54:52 +01:00
mt7981b-confiabits-mt7981.dts mediatek: add SPDX header for Confiabits MT7981 DTS 2023-12-18 08:34:10 +01:00
mt7981b-cudy-m3000-v1.dts mediatek: filogic: add support for Cudy M3000 v1 2024-07-15 16:12:33 +02:00
mt7981b-cudy-re3000-v1.dts mediatek: filogic: add support for Cudy RE3000 v1 2024-03-07 22:14:32 +01:00
mt7981b-cudy-tr3000-v1.dts mediatek: add support for Cudy TR3000 v1 2024-05-23 22:01:52 +02:00
mt7981b-cudy-wr3000-v1.dts mediatek: filogic: Cudy WR3000 v1 wps button fix 2024-02-27 12:46:06 +01:00
mt7981b-dlink-aquila-pro-ai-m30-a1.dts filogic: Add support for D-Link AQUILA PRO AI M30 2024-07-08 23:06:38 +02:00
mt7981b-glinet-gl-mt3000.dts mediatek: fix the name of buswidth to bus-width 2023-12-12 09:54:51 +01:00
mt7981b-h3c-magic-nx30-pro.dts mediatek: fiilogic: device tree switch@1f fix 2023-12-12 09:54:52 +01:00
mt7981b-jcg-q30-pro.dts mediatek: fiilogic: device tree switch@1f fix 2023-12-12 09:54:52 +01:00
mt7981b-qihoo-360t7.dts mediatek: fiilogic: device tree switch@1f fix 2023-12-12 09:54:52 +01:00
mt7981b-routerich-ax3000.dts mediatek: add support for Routerich AX3000 2024-01-04 21:47:43 +01:00
mt7981b-unielec-u7981-01-emmc.dts mediatek: filogic: add Unielec U7981-01 support 2024-03-31 20:45:20 +02:00
mt7981b-unielec-u7981-01-nand.dts mediatek: filogic: add Unielec U7981-01 support 2024-03-31 20:45:20 +02:00
mt7981b-unielec-u7981-01.dtsi mediatek: filogic: add Unielec U7981-01 support 2024-03-31 20:45:20 +02:00
mt7981b-xiaomi-mi-router-ax3000t-ubootmod.dts mediatek: filogic: add support for Xiaomi AX3000T 2024-05-23 21:50:00 +02:00
mt7981b-xiaomi-mi-router-ax3000t.dts mediatek: filogic: add support for Xiaomi AX3000T 2024-05-23 21:50:00 +02:00
mt7981b-xiaomi-mi-router-ax3000t.dtsi mediatek: filogic: add support for Xiaomi AX3000T 2024-05-23 21:50:00 +02:00
mt7981b-xiaomi-mi-router-common.dtsi mediatek: filogic: add support for Xiaomi AX3000T 2024-05-23 21:50:00 +02:00
mt7981b-xiaomi-mi-router-wr30u-stock.dts mediatek: filogic: add support for Xiaomi WR30U 2023-08-07 16:31:27 +01:00
mt7981b-xiaomi-mi-router-wr30u-ubootmod.dts mediatek: filogic: add support for Xiaomi WR30U 2023-08-07 16:31:27 +01:00
mt7981b-xiaomi-mi-router-wr30u.dtsi mediatek: filogic: add support for Xiaomi AX3000T 2024-05-23 21:50:00 +02:00
mt7981b-yuncore-ax835.dts mediatek: add support for YunCore AX835 2024-07-04 15:39:47 +02:00
mt7981b-zbtlink-zbt-z8102ax.dts mediatek: add support for Zbtlink ZBT-Z8102AX 2023-12-09 13:39:53 +01:00
mt7981b-zbtlink-zbt-z8103ax.dts mediatek: add support for Zbtlink ZBT-Z8103AX 2024-07-03 09:19:41 +02:00
mt7981b-zyxel-nwa50ax-pro.dts mediatek: add missing SPDX header 2024-07-08 12:33:11 +02:00
mt7986a-acelink-ew-7886cax.dts mediatek: filogic: add Acelink EW-7886CAX support 2023-12-12 11:02:39 +01:00
mt7986a-acer-predator-w6.dts mediatek: fiilogic: device tree switch@1f fix 2023-12-12 09:54:52 +01:00
mt7986a-asus-rt-ax59u.dts mediatek: filogic: add support ASUS RT-AX59U 2024-01-20 19:07:15 +01:00
mt7986a-asus-tuf-ax4200.dts mediatek: fiilogic: device tree switch@1f fix 2023-12-12 09:54:52 +01:00
mt7986a-asus-tuf-ax6000.dts mediatek: filogic: Asus TUF AX6000 fix inverted LED for 2.5Gb LAN port 2024-03-15 23:28:14 +01:00
mt7986a-glinet-gl-mt6000.dts mediatek: GL-MT6000: Change LED colors 2024-01-15 17:34:30 +01:00
mt7986a-jdcloud-re-cp-03.dts mediatek: add support for JDCloud RE-CP-03 2024-07-08 09:08:48 +02:00
mt7986a-netcore-n60.dts mediatek: filogic: add Netcore N60 support 2024-07-08 12:00:39 +02:00
mt7986a-smartrg-bonanza-peak.dtsi mediatek: add support for Adtran SmartRG Bonanza Peak series 2024-07-04 15:39:47 +02:00
mt7986a-smartrg-SDG-8612.dts mediatek: add support for Adtran SmartRG Bonanza Peak series 2024-07-04 15:39:47 +02:00
mt7986a-smartrg-SDG-8614.dts mediatek: add support for Adtran SmartRG Bonanza Peak series 2024-07-04 15:39:47 +02:00
mt7986a-smartrg-SDG-8622.dts mediatek: add support for Adtran SmartRG Bonanza Peak series 2024-07-04 15:39:47 +02:00
mt7986a-smartrg-SDG-8632.dts mediatek: add support for Adtran SmartRG Bonanza Peak series 2024-07-04 15:39:47 +02:00
mt7986a-tplink-tl-xdr4288.dts mediatek: sync MT7986 device trees with upstream 2023-06-09 19:23:03 +01:00
mt7986a-tplink-tl-xdr6086.dts mediatek: sync MT7986 device trees with upstream 2023-06-09 19:23:03 +01:00
mt7986a-tplink-tl-xdr6088.dts mediatek: sync MT7986 device trees with upstream 2023-06-09 19:23:03 +01:00
mt7986a-tplink-tl-xdr-common.dtsi mediatek: fiilogic: device tree switch@1f fix 2023-12-12 09:54:52 +01:00
mt7986a-xiaomi-redmi-router-ax6000-stock.dts mediatek: add new layout for Xiaomi Redmi Router AX6000 for OpenWrt U-Boot 2022-12-29 03:00:31 +00:00
mt7986a-xiaomi-redmi-router-ax6000-ubootmod.dts mediatek: add new layout for Xiaomi Redmi Router AX6000 for OpenWrt U-Boot 2022-12-29 03:00:31 +00:00
mt7986a-xiaomi-redmi-router-ax6000.dtsi mediatek: fiilogic: device tree switch@1f fix 2023-12-12 09:54:52 +01:00
mt7986a-zyxel-ex5601-t0-common.dtsi mediatek: add Zyxel EX5601-T0 with uboot custom partition 2024-02-27 17:42:30 +00:00
mt7986a-zyxel-ex5601-t0-stock.dts mediatek: add Zyxel EX5601-T0 with uboot custom partition 2024-02-27 17:42:30 +00:00
mt7986a-zyxel-ex5601-t0-ubootmod.dts mediatek: add Zyxel EX5601-T0 with uboot custom partition 2024-02-27 17:42:30 +00:00
mt7986a-zyxel-ex5700-telenor.dts mediatek: fix the name of buswidth to bus-width 2023-12-12 09:54:51 +01:00
mt7986b-mercusys-mr90x-v1.dts mediatek: fiilogic: device tree switch@1f fix 2023-12-12 09:54:52 +01:00
mt7986b-netgear-wax220.dts mediatek: fix the name of buswidth to bus-width 2023-12-12 09:54:51 +01:00