mirror of
https://github.com/openwrt/openwrt.git
synced 2025-04-09 04:15:47 +00:00
mediatek: add support for Zbtlink ZBT-Z8103AX
Specifications: SoC: MediaTek MT7981B RAM: 256MiB Flash: SPI-NAND 128 MiB Switch: 1 WAN, 3 LAN (Gigabit) Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7976CN UART: 115200n8 UART Layout: VCC-RX-TX-GND No. of Antennas: 6 Note: Upon opening the router, only 5 antennas were connected to the mainboard. Led Layout: Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi Buttons: Reset-Mesh Installation: A. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware B. Through TFTP Standard installation via UART: 1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin). 2. Power on the router. Make sure that you can access your router via UART. 3. Restart the router then repeatedly press ctrl + c to skip default boot. 4. Type > bootmenu 5. Press '2' to select upgrade firmware 6. Press 'Y' on 'Run image after upgrading?' 7. Press '0' and hit 'enter' to select TFTP client (default) 8. Fill the U-Boot's IP address and TFTP server's IP address. 9. Finally, enter the 'firmware' filename. Signed-off-by: Ian Oderon <ianoderon@gmail.com> (cherry picked from commit 4300bc668819a77226b6e8ea079d3067f216e7bb)
This commit is contained in:
Ian Oderon
Rafał Miłecki
parent
9988f8adf8
commit
77354213b7
@ -71,7 +71,8 @@ routerich,ax3000)
|
||||
;;
|
||||
cetron,ct3003|\
|
||||
netgear,wax220|\
|
||||
zbtlink,zbt-z8102ax)
|
||||
zbtlink,zbt-z8102ax|\
|
||||
zbtlink,zbt-z8103ax)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
||||
;;
|
||||
ubnt,unifi-6-plus)
|
||||
|
||||
269
target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts
Normal file
269
target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts
Normal file
@ -0,0 +1,269 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Zbtlink ZBT-Z8103AX";
|
||||
compatible = "zbtlink,zbt-z8103ax", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
led-boot = &led_status_green;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_green;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 loglevel=8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x10000000>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-mesh {
|
||||
label = "mesh";
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-wan {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
gpios = <&pio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-status-blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
gpios = <&pio 23 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_green: led-status-green {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
gpios = <&pio 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_status_red: led-status-red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
gpios = <&pio 25 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-wlan2g {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
gpios = <&pio 34 GPIO_ACTIVE_LOW>;
|
||||
function-enumerator = <0>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
led-wlan5g {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
gpios = <&pio 35 GPIO_ACTIVE_LOW>;
|
||||
function-enumerator = <1>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
/* LAN */
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_factory_4 2>;
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
/* WAN */
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_factory_4 3>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
switch: switch@1f {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <31>;
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand@0 {
|
||||
compatible = "spi-nand";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bl2";
|
||||
reg = <0x0000000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x100000 0x80000>;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x200000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x4 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x580000 0x4000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
label = "cpu";
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
nvmem-cells = <&eeprom_factory>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
};
|
||||
@ -44,6 +44,9 @@ xiaomi,redmi-router-ax6000-stock|\
|
||||
xiaomi,redmi-router-ax6000-ubootmod)
|
||||
ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan"
|
||||
;;
|
||||
zbtlink,zbt-z8103ax)
|
||||
ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx"
|
||||
;;
|
||||
zyxel_ex5601-t0-stock|\
|
||||
zyxel,ex5601-t0-ubootmod)
|
||||
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" "link tx rx"
|
||||
|
||||
@ -36,7 +36,8 @@ mediatek_setup_interfaces()
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan"
|
||||
;;
|
||||
cmcc,rax3000m|\
|
||||
h3c,magic-nx30-pro)
|
||||
h3c,magic-nx30-pro|\
|
||||
zbtlink,zbt-z8103ax)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1
|
||||
;;
|
||||
cudy,tr3000-v1|\
|
||||
|
||||
@ -113,6 +113,7 @@ case "$board" in
|
||||
;;
|
||||
routerich,ax3000|\
|
||||
zbtlink,zbt-z8102ax|\
|
||||
zbtlink,zbt-z8103ax|\
|
||||
zyxel,ex5601-t0|\
|
||||
zyxel,ex5601-t0-ubootmod)
|
||||
addr=$(mtd_get_mac_binary "Factory" 0x4)
|
||||
|
||||
@ -885,6 +885,23 @@ define Device/zbtlink_zbt-z8102ax
|
||||
endef
|
||||
TARGET_DEVICES += zbtlink_zbt-z8102ax
|
||||
|
||||
define Device/zbtlink_zbt-z8103ax
|
||||
DEVICE_VENDOR := Zbtlink
|
||||
DEVICE_MODEL := ZBT-Z8103AX
|
||||
DEVICE_DTS := mt7981b-zbtlink-zbt-z8103ax
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
|
||||
KERNEL_IN_UBI := 1
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE)
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += zbtlink_zbt-z8103ax
|
||||
|
||||
define Device/zyxel_ex5601-t0-stock
|
||||
DEVICE_VENDOR := Zyxel
|
||||
DEVICE_MODEL := EX5601-T0
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user