Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.
[*] As a funny side-fact, copy-pasting has led to almost all
hotplug.d files using the "+", while nearly all of the
02_network files are not using it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600
Descriptions:
Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
really different, the only hardware difference between the two models is flash
size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
compatible with YK-L1's firmware but it's better to split it to different models.
It is easy to identify the models by looking at the label on the bottom of the
device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
to install compatible firmware, so please backup config file before system upgrade.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove the USB status red and green LEDs for
- ADB P.DG A4001N A-000-1A1-AX
- Technicolor TG582N
- Technicolor TG582N Telecom Italia
After having mounted an SMD socket for the flash memory for
JTAG reverse engineering, and so be able to easly swap between
OpenWrt and the stock FW, it turned out that the stock FW does
not light up the red and green USB LEDs exactly as I remembered.
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[improve commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CPExxx and WBSxxx boards with AR9344 SOC
use the OKLI lzma kernel loader
with the offset of 3 blocks of length 4k (0x3000)
in order to have a fake "kernel" that cannot grow larger
than how it is defined in the now static OEM partition table.
Before recent changes to the mtdsplit driver,
the uImage parser for OKLI only supported images
that started exactly on an eraseblock boundary.
The mtdsplit parser for uImage now supports identifying images
with any magic number value
and at any offset from the eraseblock boundary
using DTS properties to define those values.
So, it is no longer necessary to use fixed sizes
for kernel and rootfs
Tested-by: Andrew Cameron <apcameron@softhome.net> [CPE510 v2]
Tested-by: Bernhard Geier <freifunk@geierb.de> [WBS210 v2]
Tested-by: Petrov <d7c48mWsPKx67w2@gmail.com> [CPE210 v1]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This adds support for the Askey RT4230W REV6
(Branded by Spectrum/Charter as RAC2V1K)
At this time, there's no way to reinstall the stock firmware so don't install
this on a router that's being rented.
Specifications:
Qualcomm IPQ8065
1 GB of RAM (DDR3)
512 MB Flash (NAND)
2x Wave 2 WiFi cards (QCA9984)
5x 10/100/1000 Mbps Ethernet (Switch: QCA8337)
1x LED (Controlled by a microcontroller that switches it between red and
blue with different patterns)
1x USB 3.0 Type-A
12V DC Power Input
UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V
Port settings are 115200n8
More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830https://deviwiki.com/wiki/Askey_RAC2V1K
To check what revision your router is, restore one of these config backups
through the stock firmware to get ssh access then run
"cat /proc/device-tree/model".
https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17
The revision number on the board doesn't seem to be very consistent so that's
why this is needed. You can also run printenv in the uboot console and if
machid is set to 177d, that means your router is rev6.
Note: Don't install this if the router is being rented from an ISP. The defined
partition layout is different from the OEM one and even if you changed the
layout to match, backing up and restoring the OEM firmware breaks /overlay so
nothing will save and the router will likely enter a bootloop.
How to install:
Method 1: Install without opening the case using SSH and tftp
You'll need:
RAC2V1K-SSH.zip:
https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip
initramfs and sysupgrade images
Connect to one of the router's LAN ports
Download the RAC2V1K-SSH.zip file and restore the config file that
corresponds to your router's firmware (If you're firmware is newer than what's
in the zip file, just restore the 1.1.16 file)
After a reboot, you should be able to ssh into the router with username:
"4230w" and password: "linuxbox" or "admin". Run the following commannds
fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as
it's in the same subnet as the server
fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next
steps
fw_setenv bootdelay 8
fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq"
Don't reboot the router yet.
Install and set up a tftp server on your computer
Set a static ip on the ethernet interface of your computer (use this for
serverip in the above commands)
Rename the initramfs image to initramfs.bin, and host it with the tftp
server
Reboot the router. If you set up everything right, the router led should
switch over to a slow blue glow which means openwrt is booted. If for some
reason the file doesn't get loaded into ram properly, it should still boot to
the OEM firmware.
After openwrt boots, ssh into it and run these commands:
fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts
mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi
read 0x44000000 kernel 0x6e0000 && bootm"
fw_setenv bootdelay 2
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Method 2: Install with serial access (Do this if something fails and you can't
boot after using method 1)
You'll need:
initramfs and sysupgrade images
Serial access:
https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case
Install and set up a tftp server
Set a static ip on the ethernet interface of your computer
Download the initramfs image, rename it to initramfs.bin, and host it with
the tftp server
Connect the wan port of the router to your computer
Interrupt U-Boot and run these commands:
setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer)
setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet)
setenv bootcmd "setenv mtdids nand0=nand0 &&
set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware
&& ubi read 0x44000000 kernel 0x6e0000 && bootm"
saveenv
tftpboot initramfs.bin
bootm
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Signed-off-by: Lauro Moreno <lmore377@gmail.com>
[add entry in 5.10 patch, fix whitespace issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2 and EA7500 v2.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Leon Poon (@LeonPoon) for the initial bringup.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
[add missing entry in 10_fix_wifi_mac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips. The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.
Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART: through-hole on PCB.
J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
pin3=GND, pin4=TX. Settings: 57600/8N1.
Note regarding dual system partitions
-------------------------------------
The vendor firmware and boot loader use a dual partition scheme. The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.
OpenWrt does not support this scheme and will always use the first OS
partition. It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.
Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used. We first flash an initramfs image, then
follow with a regular sysupgrade.
Installation:
Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
(Alternatively, you can use the TFTP recovery method below.)
You can use WiFi or Ethernet.
The direct URL is: http://192.168.3.1/07_06_00_firmware.html
a. No login is needed, and you'll be in their setup wizard.
b. You might get a warning about not being connected to the Internet.
c. Towards the bottom of the page will be a section entitled "Or
Manually Upgrade Firmware from a File:" where you can manually choose
and upload a firmware file.
d: Click "Choose File", select the OpenWRT "initramfs" image and click
"Upload."
2) The Router will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image. Note:
you may use the sysupgrade command line tool in lieu of the UI if
you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
of OpenWRT. Start by configuring a computer as a TFTP client:
a. Install a TFTP client (server not necessary)
b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
a. Do this by pressing and holding the reset button on the bottom while
connecting the power.
b. As soon as the LED lights up green (roughly 2-3 seconds), release
the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image. Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Backup the OEM Firmware:
-----------------------
There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.
The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem"). We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.
1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
2) Under "Save mtdblock contents," first select "firmware" and click
"Save mtdblock" to download the image.
3) Repeat the process, but select "oem" from the pull-down menu.
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow the TFTP recovery steps for the Extender, and use the
backup image.
* OpenWrt "Flash Firmware" interface:
Upload the backup image and select "Force update"
before continuing.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
This submission relied heavily on the work of Linksys EA7300 v1/ v2.
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: 128M DDR3-1600
* Flash: 128M NAND
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7603E/MT7613BE (2.4 GHz & 5 GHz)
* Antennae: 2 internal fixed in the casing and 2 on the PCB
* LEDs: Blue (x4 Ethernet)
Blue+Orange (x2 Power + WPS and Internet)
* Buttons: Reset (x1)
WPS (x1)
Installation:
Flash factory image through GUI.
This device has 2 partitions for the firmware called firmware and
alt_firmware. To successfully flash and boot the device, the device
should have been running from alt_firmware partition. To get the device
booted through alt_firmware partition, download the OEM firmware from
Linksys website and upgrade the firmware from web GUI. Once this is done,
flash the OpenWrt Factory firmware from web GUI.
Reverting to factory firmware:
1. Boot to 'alt_firmware'(where stock firmware resides) by doing one of
the following:
Press the "wps" button as soon as power LED turns on when booting.
(OR) Hard-reset the router consecutively three times to force it to
boot from 'alt_firmware'.
2. To remove any traces of OpenWRT from your router simply flash the OEM
image at this point.
Signed-off-by: Aashish Kulkarni <aashishkul@gmail.com>
[fix hanging indents and wrap to 74 characters per line,
add kmod-mt7663-firmware-sta package for 5GHz STA mode to work,
remove sysupgrade.bin and concatenate IMAGES instead in mt7621.mk,
set default-state "on" for power LED]
Signed-off-by: Sannihith Kinnera <digislayer@protonmail.com>
[move check-size before append-metadata, remove trailing whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Specifications:
SoC: QCA9533
DRAM: 32Mb DDR1
Flash: 8/16Mb SPI-NOR
LAN: 4x 10/100Mbps via AR8229 switch (integrated into SoC)
on GMII
WAN: 1x 10/100Mbps via MII
WLAN: QCA9530
USB: 1x 2.0
UART: standard QCA UART header
JTAG: yes
Button: 1x WPS, 1x reset
LEDs: 8x LEDs
A version with 4Mb flash is also available, but due to lack of
enough space it's not supported.
As the original flash layout does not provide enough space for
the kernel (1472k), the firmware uses OKLI and concat flash to
overcome the limitation without changing the boot address of the
bootloaders.
Installation:
1. Original bootloader
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
available via TFTP
tftpboot 0x80060000 openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
Reboot the board.
2. pepe2k's u-boot_mod
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
available via TFTP, as "firmware.bin"
run fw_upg
Reboot the board.
For the 16M version of the board, please use
openwrt-ath79-generic-qca_ap143-16m-squashfs-factory.bin
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
[use fwconcatX names, drop redundant uart status, fix IMAGE_SIZE,
set up IMAGE/factory.bin without metadata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8031 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
ar8xxx_soft_reset is effectively a NOP function. In the PHY state
machine, the availability and result of a soft_reset function
makes no difference for the code flow.
Thus, we can safely remove this method.
Signed-off-by: David Bauer <mail@david-bauer.net>
Modifying PHY capabilities in the probe function broke with upstream
commit 92ed2eb7f4b7 ("net: phy: probe the PHY before determining the
supported features").
AR8316 switches only support 10/100 Mbit/s link modes because of this
change.
Provide a get_features method for the PHY driver, so Gigabit link mode
will be advertised to link partners again.
Signed-off-by: David Bauer <mail@david-bauer.net>
Run `make kernel_oldconfig CONFIG_TARGET=subtarget`
This mostly aims at getting rid of redundant/unneeded symbols.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add missing symbol CONFIG_AHCI_XGENE.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[also add for 5.10, remove from layerscape target config]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug
wireless router. This device is also sold under the name SilverCrest
SWV 733 A2.
Device Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high
- Buttons: Reset, WPS
- Sliding mode switch: AP, repeater, client
- Small sliding power switch
Flashing instructions:
U-Boot launches TFTP client if WPS button is pressed during power-on.
Configure as follows:
- Server IP: 192.168.10.100
- Filename (rename sysupgrade file to this): firmware.bin
Flashing should not take more than a minute, device will reboot
automatically.
Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The patch was not applied to the v5.4 target, thus breaking Kernel 5.4
on devices with multiple flash chips attache to the SPI bus.
Fixes commit bd54e73954 ("ath79: set number of chipselect lines")
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications
SoC: MT7621
CPU: 880 MHz
Flash: 16 MiB
RAM: 128 MiB
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac
MT7603E / MT7615E
Ethernet: 5x Gbit ports
Installation
There are two known options:
1) The Luci-based UI.
2) Press and hold the reset button during power up.
The router will request 'recovery.bin' from a TFTP server at
192.168.1.88.
Both options require a signed firmware binary.
The openwrt image supplied by cudy is signed and can be used to
install unsigned images.
R4 & R5 need to be shorted (0-100Ω) for the UART to work.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[remove non-required switch-port node - remove trgmii phy-mode]
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for TP-Link Archer C6U v1 (EU).
The device is also known in some market as Archer C6 v3.
This patch supports only Archer C6U v1 (EU).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (Winbond 25Q128)
* WiFi 5GHz: Mediatek MT7613BEN (2x2:2)
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2)
* Ethernet: MT7630, 5x 1000Base-T.
* LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB
* Buttons: Reset, WPS.
* UART: Serial console (115200 8n1), J1(GND:3)
* USB: One USB2 port.
Installation:
------------
Install the OpenWrt factory image for C6U is from the
TP-Link web interface.
1) Go to "Advanced/System Tools/Firmware Update".
2) Click "Browse" and upload the OpenWrt factory image:
openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin.
3) Click the "Upgrade" button, and select "Yes" when prompted.
Recovery to stock firmware:
--------------------------
The C6U bootloader has a failsafe mode that provides a web
interface (running at 192.168.0.1) for reverting back to the
stock TP-Link firmware. The failsafe interface is triggered
from the serial console or on failed kernel boot. Unfortunately,
there's no key combination that enables the failsafe mode. This
gives us two options for recovery:
1) Recover using the serial console (J1 header).
The recovery interface can be selected by hitting 'x' when
prompted on boot.
2) Trigger the bootloader failsafe mode.
A more dangerous option is force the bootloader into
recovery mode by erasing the OpenWrt partition from the
OpenWrt's shell - e.g "mtd erase firmware". Please be
careful, since erasing the wrong partition can brick
your device.
MAC addresses:
-------------
OEM firmware configuration:
D8:07:B6:xx:xx:83 : 5G
D8:07:B6:xx:xx:84 : LAN (label)
D8:07:B6:xx:xx:84 : 2.4G
D8:07:B6:xx:xx:85 : WAN
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
The patch adds support for the TP-Link Archer A6 v3
The router is sold in US and India with FCC ID TE7A6V3
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated from serial console only.
Press 'x' while u-boot is starting
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Thanks to: Frankis for Randmon MAC address fix.
Signed-off-by: Vinay Patil <post2vinay@gmail.com>
[remove superfluous factory image definition, whitespacing]
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes Gateworks Ventana 'DEVICE_NAME' variable which value wasn't
adjusted during migration to common 'vendor_model' image naming scheme
(fixes: FS#3825).
Furthermore, drop unused 'Build/boot-scr' recipe, get rid of redundant
'BOOT_SCRIPT' variable (use already provided 'DEVICE_NAME' instead) and
drop custom 'DEVICE_NAME' variable from SolidRun CuBox-i image recipe
(use default one instead).
Fixes: cbc8bcfbaa ("imx6: image: use vendor_model scheme")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This updates the patches to match the versions included in the mtd
subsystem for the next Linux kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rid of kernel error message:
[ 0.780828] orion-mdio d0072004.mdio: IRQ index 0 not found
on Marvell targets backporting the kernel commit fa2632f74e57
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The higher 16-bit of EEE register was overwritten by mistake, fix that.
Fixes: 5b9ba4a93e ("generic: mt7530: support adjusting EEE")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
The previous config will only show 2.4G radio activity status
This change mr24:green:wifi4 and mr24:green:wifi2 to
show 2.4G and 5G radio on and off status
change mr24:green:wifi3 and mr24:green:wifi1 to
show 2.4G and 5G radio activity status
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Backport a pending patch already reviewed that fix some warning about tsens debugs already registered.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
With some talk with the ARM maintainer, it was notice that enlarging the limit
to the current value is VERY wrong and clash with other memory.
A better solution would be to reduce the IO space from 1MB to 64K as probably
it's a long lasting typo and even x86 arch doesn't have a IO space that big.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Removed upstreamed:
generic/pending-5.4/770-02-net-ethernet-mtk_eth_soc-fix-rx-vlan-offload.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Note that since I rebased the previous commit, I removed my Run-tested line
although I confirm building the image successfully.
Signed-off-by: John Audia <graysky@archlinux.us>
Removed upstreamed:
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
bcm63xx/patches-5.4/434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch*
Removed/code was included upstream and therefore redundant:
ramips/patches-5.4/999-fix-pci-init-mt7620.patch
All other patches automatically rebased.
* update_kernel.sh did not flag this yet it was included in 5.4.119[1], as a
result of the rebase, I removed my testing lines since I did not go back to
test built or to run test 5.4.119 with the removed patch present.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.4.119&id=e5b3e69eb36ac1178a7a2392616fd29afd288c4e
Signed-off-by: John Audia <graysky@archlinux.us>
This switches device names to the common 'vendor_model' approach as in
most of other targets in OpenWrt.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
- drop unused 'UBOOT' variable from 'Device/apalis' recipe
- fix 'KERNEL_SUFFIX' for 'Device/cubox-i' (should be '-zImage')
- drop redundant 'DEVICE_{VENDOR,MODEL}' from 'Device/ventana-large'
- other, minor fixes
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This reduces redundant instructions.
The solution is inspired by a different implemention of
Roman Kuzmitskii.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional
antenna. It is low cost and mostly available via Aliexpress, references can
be found at:
- https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383
- https://git.lsd.cat/g/openwrt-cpe46b
Specifications:
- Atheros AR9330
- 32MB of RAM
- 8MB of flash (SPI NOR)
- 1 * 2.4ghz integrated antenna
- 2 * 10/100/1000 ethernet ports (1 POE)
- 3 * Green LEDs controlled by the SoC
- 3 * Green LEDs controlled via GPIO
- 1 * Reset Button controlled via GPIO
- 1 * 4 pin serial header on the PCB
- Outdoor packaging
Flashing instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor
Telnet console is vulnerable to command injection and can be used to gain
a shell directly on the OEM OpenWrt distribution.
Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org>
[fix whitespaces, drop redundant uart status and serial0, drop
num-chipselects, drop 0x1002 MAC address for wmac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
COMFAST CF-E375AC is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
1) Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
2) TFTP
2.1) Set a tftp server on your machine with a fixed IP address of
192.168.1.10. A place the sysupgrade as firmware_auto.bin.
2.2) boot the device with an ethernet connection on fixed ip route
2.3) wait a few seconds and try to login via ssh
3) TFTP trough Bootloader
3.1) open the device case and get a uart connection working
3.2) stop the autoboot process and test connection with serverip
3.3) name the sysupgrade image firmware.bin and run firmware_upg
MAC addresses:
Though the OEM firmware has four adresses in the usual locations,
it appears that the assigned addresses are just incremented in a
different way:
interface address location
LAN: *:DC 0x0
WAN *:DD 0x1002
WLAN 2.4g *:E6 n/a (0x0 + 10)
WLAN 5g *:DE 0x6
unused *:DF 0x5006
The MAC address pointed at the label is the one assign to the LAN
interface.
Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com>
[add label-mac-device, remove redundant uart status, fix whitespace
issues, fix commit message wrapping, remove x bit on DTS file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ubiquiti EdgeRouter 6P is 6 port router with similar
specifications as the EdgeRouter 4, support for which was added
in commit dd651e54cc
There are five 10/100/1000 Mbps RJ/Copper ports and
one 1000 Mbps SFP port.
SoC: Octeon Cavium 7130 (Cavium 3) at 1000MHz
Memory: 1GiB DDR3
Flash: 2x2M chips with uboots (chainloaded) + 512K eeprom
LEDs: 1x for power status (white/blue, controllable)
and 6x for ethernet and SFP ports (no control over them)
Buttons: 1x Reset
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1
USB: 1x USB3.0 on front panel
MII: 1x QSGMII from SoC
PHY: 1x Vitesse VSC8504 of which 4 ports are used (phys 4-7)
1x Vitesse VSC8514 of which 2 ports are used (phys 8-9)
Network port mapping
- eth0 on device maps to lan0 and phy5
- eth1 on device maps to lan1 and phy6
- eth2 on device maps to lan2 and phy7
- eth3 on device maps to lan3 and phy8
- eth4 on device maps to lan4 and phy9
- eth5 (SFP) on device maps to lan5 and phy4
What is not working:
- There is no port status available before it goes up
- SFP have no additional status and presented as no different from eth
- Power-over-ethernet (passive) support has not been tested
How to flash the firmware:
- copy openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin and
openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar to
USB flash drive that is formatted to vfat/fat32
- connect USB flash drive to EdgeRouter 6P front USB port
- connect serial cable using front RJ45 port (115200 baud, 8N1)
- connect power to cable to EdgeRouter 6P
- connect terminal to the console to see uboot boot process
- interrupt boot by pressing button(s) on your keyboard to log
in to the uboot
- detect usb connected flash drives by typing to the console:
usb start
- after drive is detected load initramfs+kernel to the memory by typing:
fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin
- after initramfs+kernel is loaded to the memory load it by typing:
bootoctlinux 0 numcores=4 endbootargs mem=0
- boot process should finish and you will be greeted with console
after pressing enter
- create directory to mount usb flash drive to by typing:
mkdir /tmp/sda
- mount flash drive to that directory by typing:
mount /dev/sda1 /tmp/sda
- flash firmware to router internal storage by typing:
sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar
- device will reboot and after it gets up you will have
edgerouter 6p running openwrt
Signed-off-by: Dan Brown <danbrown@gmail.com>
[reorder/squash patches, move ethernet@0 to DTS, share image setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
EdgeRouter 4 and upcoming EdgeRouter 6P and 12 have similar setup,
so create a shared DTSI to prevent duplicate code.
Signed-off-by: Dan Brown <danbrown@gmail.com>
[reorder/squash commits, add description, move ethernet@0 to DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Vendor firmware expects model name without manufacturer name inside
'supported_devices' part of metadata. This allows direct upgrade to
OpenWrt from vendor's GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This fixes a small regression where the lzma-loader variable values
are being shared between boards that require different configurations.
If not set to "" globally, a device without these settings will just take
the last values another device has set before in the queue.
Fixes: 1b8bd17c2d ("ath79: lzma-loader: allow setting custom kernel magic")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[add detailed explanation to the commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. In most of the cases, I just saw warnings like this:
make: Entering directory '/home/.../package/gluon-status-page'
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
[...]
While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.
After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
Fixes following error while executing the init script on the buildhost:
Enabling boot
./etc/init.d/bootcount: line 5: /lib/upgrade/asrock.sh: No such file or directory
Enabling bootcount
While at it fix following shellcheck issue:
base-files/etc/init.d/bootcount line 11:
if [ $? -eq 0 ]; then
^-- SC2181: Check exit code directly with e.g. 'if mycmd;', not indirectly with $?.
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Cc: Pawel Dembicki <paweldembicki@gmail.com>
Cc: Christian Lamparter <chunkeey@gmail.com>
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
References: https://gitlab.com/ynezz/openwrt/-/jobs/1243290743#L1444
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The code uses get_mtd_device_nm() which must be followed by a call to
put_mtd_device() once the handle is no longer used.
This fixes spurious shutdown console messages such as:
[ 2256.334562] Removing MTD device #7 (soft_config) with use count 1
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
311-MIPS-zboot-put-appended-dtb-into-a-section.patch
commit d2e850e96183 in kernel, part of v5.11
499-mtd-don-t-lock-when-recursively-deleting-partitions.patch
commit cb4543054c5c in kernel, part of v5.13
103-MIPS-select-CPU_MIPS64-for-remaining-MIPS64-CPUs.patch
commit 5a4fa44f5e1b in kernel, part of v5.13
Move them to backports folder to make maintainance easier.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MAC addresses read from official firmware
value location
Wlan xx 71 de factory@0x04
Lan xx 71 dd factory@0x28
Wan xx 71 df factory@0x2e
Label xx 71 dd factory@0x28
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix sorting in 02_network, redact commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds the CPU port to the unknown multicast flooding port mask,
which fixes the VLAN issues introduced by the multicast group patches
Tested-by: Russell Senior <russell@personaltelco.net> [Netgear GS108Tv3]
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no> [whitespace fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz> [unknwon typo fix]
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E
- Switch: 1 LAN port (Gigabiti)
- 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
- SIM: 2 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/yellow under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable. Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.
A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.
MAC addresses:
OpenWrt OEM Address Found as
lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label
wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex)
wwan0 usb0 random
WARNING!!
ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled. Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.
Installation from OEM web GUI:
- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Installation from OEM ssh:
- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
nvram setro uboot DebugFlag 0x1
nvram setro uboot CheckBypass 0
nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Copying OpenWrt to the recovery partition:
- Verify that you are running a working OpenWrt recovery image
from flash
- ssh to root@192.168.1.1 and run:
fw_setenv CheckBypass 0
mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2
NOTE: This should only be done after successfully booting the OpenWrt
recovery image from the primary partition during installation. Do
not do this after having sysupgraded OpenWrt! Reinstalling the
recovery image on normal upgrades is not required or recommended.
Installation from Z-Loader:
- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image
NOTE: ATNR will write the recovery image to both primary and recovery
partitions in one go.
Booting from RAM:
- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
header
This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies! Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.
NOTE: U-Boot configuration is incomplete (on some devices?). You may
have to configure a working mac address before running tftp using
"setenv eth0addr <mac>"
Unlocking the bootloader:
If you are unebale to halt boot, then the bootloader is locked.
The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0. Setting it to 1 is therefore only temporary
when OEM firmware is installed.
- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt
NOTE:
OpenWrt does this automatically on first boot if necessary
NOTE2:
Setting the flag to 0x1 avoids the reset to 0 in known OEM
versions, but this might change.
WARNING:
Writing anything to flash while the bootloader is locked is
considered extremely risky. Errors might cause a permanent
brick!
Enabling management access from LAN:
Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:
- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"
Notes on the OEM/bootloader dual partition scheme
The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.
Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.
The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.
If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.
If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.
If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally. CheckBypass is set to 1 after each successful
validation of Image1.
Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger. But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.
The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.
Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.
Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
ath79, lantiq, ipq40xx, ramips all use the OpenWrt-specific gpio-export
functionality. Consolidate the patch that adds it under hack-5.10 since
this logic is obviously not target-specific. For those who want to
disable it, unsetting CONFIG_GPIO_SYSFS symbol will disable this code.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Kernel 5.10 support for ipq806x was added at the same time that these
patches were developed for kernel 5.4. This carries the patches forward
to kernel 5.10.
fa731838c5 ipq806x: dwmac: clear forced speed during probe
75ca641f1b ipq806x: Add "snps,dwmac" to all gmac compatible=
d62825dd77 ipq806x: dwmac: set forced speed when using fixed-link
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
d53be2a2e9 migrated 0069-arm-boot-add-dts-files.patch from patches-5.4
to patches-5.10, but a subsequent patch in that set, 1e25423be8,
erroneously removed several devices:
ipq8062/nec,wg2600hp3 from 3bb1618573
ipq8064/asrock,g10 from 98b86296e6
ipq8064/ubnt,unifi-ac-hd from 4e46beb313
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
fa731838c5 cleared the forced speed in the QSGMII PCS_ALL_CH_CTL
register during probe, but this is only correct for GMACs that are not
configured with fixed-link. This prevented GMACs configured with both
phy-mode = "sgmii" and fixed-link from working properly, as discussed at
https://github.com/openwrt/openwrt/pull/3954#issuecomment-834625090 and
the comments that follow. Notably, this prevented all communication
between gmac2 and the switch on the Netgear R7800.
The correct behavior is to set the QSGMII PCS_ALL_CH_CTL register by
considering the gmac's fixed-link child, setting the speed as directed by
fixed-link if present, and otherwise clearing it as was done previously.
Fixes: fa731838c5 ("ipq806x: dwmac: clear forced speed during probe")
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Run-tested: ipq806x/ubnt,unifi-ac-hd, ipq806x/netgear,r7800
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Ansuel Smith <ansuelsmth@gmail.com>
The routerbootparts driver dynamically discovers the location of MikroTik
partitions, but it cannot determine their size (except by extending them
up to the start of the next discovered partition).
The hard_config partition has a default size of 0x1000 in the driver,
while it actually takes 0x2000 on the hAP-ac2. Set the correct size in
the hAP-ac2 DTS.
On most devices, this isn't a problem as the actual data fits in 0x1000
bytes. However, some devices have larger data that doesn't fit in 0x1000
bytes. In any case, all devices seen so far have enough space for a
0x2000 hard_config partition before the start of the dtb_config partition.
With the current 0x1000 size:
0x00000000e000-0x00000000f000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"
With this patch extending the size to 0x2000:
0x00000000e000-0x000000010000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"
Other ipq40xx boards may need the same fix but it needs testing.
References: https://forum.openwrt.org/t/support-for-mikrotik-hap-ac2/23333/324
Acked-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Adds support for Layer 2 multicast by implementing the DSA port_mdb_*
callbacks. The Kernel bridge listens to IGMP/MLD messages trapped to
the CPU-port, and calls the Multicast Forwarding Database updates.
The updates manage the L2 forwarding entries and the multicast
port-maps.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This sets up all VLANs with a default configuration on reset:
- forward based on VLAN-ID and not the FID/MSTI
- forward based on the inner VLAN-ID (not outer)
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds SoC specific VLAN configuration routines, which
alsoe sets up the portmask table entries that are referred to
in the vlan profiles registers for unknown multicast flooding.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds support for the MMD access registers the RTL-SoCs use to access clause 45
PHYs via mdio.
This new interface is used to add EEE-support for the RTL8226
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Adds a hash-bucket size attribute for the different SoCs, in order to
accomodate the buckets with 8 entries of the L2-forwarding tables
on RTL93XX in contrast to only 4 on RTL83XX.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds snooping support for IGMP and MLD on RTL8380/90/9300
by trapping IGMP and MLD packets to the CPU.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Enables CRC calculation offloading on RTL8380/8390/9300.
Tested on Zyxel XGS1210-10 (RTL9302)/GS1900-48 (RTL8390)/GS1900-10HP (RTL8382)
On the Zyxel GS1900-10HP, an increase of 5% in iperf3 send throughput
and 11% in receive throughput is seen.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
wakeup-source is required for gpio keys to fix error
genirq: irq_chip msmgpio did not update eff. affinity mask
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
- Add new tsens node
- Add new cpufreq required nodes
- Drop arm cpuidle compatible
- Fix duplicate node set upstream
- Add voltage tolerance value for cpu opp
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
ipq806x have different ecc configuration for boot partition and rootfs partition. Add support for this to fix IO error on mtd block scan.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The spm driver now has dedicated support for krait cpu idle state. We don't need to add generic arm cpuidle support for qcom.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Patch 0030 wrongly disables gsbi1 instead of gsbi4.
Fix the wrong patch and also include other fix from the original qsdk source.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Various report and data show that the freq 384000 is too low and cause some
extra latency to the entire system. OEM qsdk code also set the min frequency
for this target to 800 mhz.
Also some user notice some instability with this idle frequency, solved by
setting the min frequency to 600mhz. Fix all these kind of problem by
introducing a boot init.d script that set the min frequency to 600mhz and set
the ondemand governor to be more aggressive. The script set these value only if
the ondemand governor is detected. 384 mhz freq is still available and user can
decide to restore the old behavior by disabling this script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
INABA Abaniact AML2-17GP is a 17 port gigabit switch, based on RTL8382.
Specification:
- SoC : Realtek RTL8382
- RAM : DDR3 128 MiB (SK hynix H5TQ1G63EFR)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FZ2I-10G)
- Ethernet : 10/100/1000 Mbps x17
- port 1-8 : RTL8218B (SoC)
- port 8-16 : RTL8218D
- port wan : RTL8214FC
- LEDs/Keys : 1x, 1x
- UART : pin header on PCB (Molex 530470410 compatible)
- J14: 3.3V, GND, RX, TX from rear side
- 115200n8
- Power : 100-240 VAC, 50/60 Hz, 0.21 A
- Plug : IEC 60320-C13
Flash instruction using initramfs image:
1. Boot AML2-17GP normally
2. Set the IP address of computer to the range of 192.168.1.0/24, other
than 192.168.1.248 and connect computer to "WAN/CONSOLE" port of
AML2-17GP
3. Access to "http://192.168.1.248" and open firmware setting page
-- UI Language: 日本語 --
"メンテナンス" -> "デュアルイメージ"
-- UI Language: ENGLISH --
"Maintenance" -> "Dual Image"
4. Check "イメージ情報 (en: "Images Information")" and set the first
image to active by choosing "アクティブイメージ" (en: "Active
Image") in the partition "0"
5. open firmware upgrade page
-- UI Language: 日本語 --
"メンテナンス" -> "アップグレードマネージャー"
-- UI Language: ENGLISH --
"Maintenance" -> "Upgrade Manager"
6. Set the properties as follows
-- UI Language: 日本語 --
"アップグレード方式" : "HTTP"
"アップグレードタイプ" : "イメージ"
"イメージ" : "アクティブ"
"ブラウズファイル" : (select the OpenWrt initramfs image)
-- UI Language: ENGLISH --
"Upgrade Method" : "HTTP"
"Upgrade Type" : "Image"
"Image" : "(Active)"
"Browse file" : (select the OpenWrt initramfs image)
7. Press "アップグレード" (en: "Upgrade") button and perform upgrade
8. Wait ~150 seconds to complete flashing
9. After the flashing, the following message is showed and press "OK"
button to reboot
-- UI Language: 日本語 --
"成功!! 今すぐリブートしますか?"
-- UI Language: ENGLISH --
"Success!! Do you want to reboot now?"
10. After the rebooting, reconnect the cable to other port (1-16) and
open the SSH connection, download the sysupgrade image to the device
and perform sysupgrade with it
11. Wait ~120 seconds to complete sysupgrade
Note:
- The uploaded image via WebUI will only be written with the length
embedded in the uImage header. If the sysupgrade image is specified,
only the kernel is flashed and lacks the rootfs, this causes a kernel
panic while booting and bootloops.
To avoid this issue, initramfs image is required for flashing on WebUI
of stock firmware.
- This device has 1x LED named as "POWER", but it's not connected to the
GPIO of SoC and cannot be controlled.
- port 17 is named as "WAN/CONSOLE". This port is for the upstream
connection and console access (telnet/WebUI) on stock firmware.
Back to stock firmware:
1. Set "bootpartition" variable in u-boot-env2 partition to "1" by
fw_setsys
fw_setsys bootpartition 1
2. Reboot AML2-17GP
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The Netgear GS308T v1 is an 8 port gigabit switch. The GS310TP v1 is an 8
port POE+ gigabit switch with 2 SFP Ports (currently untested).
The GS308T v1 and GS310TP v1 are quite similar to the Netgear GS1xx
devices already supported. Theses two devices use the same Netgear
firmware and are very similar to there corresponding GS1xx devices. For
this reason they share a large portion of the device tree with the GS108T
and GS110TP with exception of the uimage magic and model and compatible
values.
All of the above feature a dual firmware layout, referred to as Image0
and Image1 in the Netgear firmware.
In order to manipulate the PoE+ on the GS310TP v1 , one needs the
rtl83xx-poe package
Specifications (GS308T)
----------------------
* RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
* 32MB 3v NOR SPI Flash (Winbond W25Q256JVFQ)
* RTL8231 GPIO extender to control the LEDs and the reset button
* 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B)
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
* Power is supplied via a 12V 1A barrel connector
Specifications (GS310TP)
----------------------
* RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
* Nuvoton M0516LDN for controlling PoE
* 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
* 32MB 3v NOR SPI Flash (Winbond W25Q256JVFQ)
* RTL8231 GPIO extender to control the LEDs and the reset button
* 8 x 10/100/1000BASE-T PoE+ ports, 2 x Gigabit SFP ports,
internal PHY (RTL8218B)
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
* Power is supplied via a 54V 1.25A barrel connector
Both devices have UART pinout
-----------
J1 | [o]ooo
^ ||`------ GND
| |`------- RX [TX out of the serial adapter]
| `-------- TX [RX into the serial adapter]
`---------- Vcc (3V3) [the square pin]
The through holes are filled with PB-free solder which melts at 375C.
They can also be drilled using a 0.9mm bit.
Installation
------------
Instructions are identical to those for the similar Negear devices
and apply both to the GS308T v1 and GS310TP v1 as well.
-------------------
Boot initramfs image from U-Boot
--------------------------------
1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
2. Init network with `rtk network on` command
3. Load image with `tftpboot 0x8f000000
openwrt-realtek-generic-netgear_gs308t-v1-initramfs-kernel.bin` command
4. Boot the image with `bootm` command
The switch defaults to IP 192.168.1.1 and tries to fetch the image via
TFTP from 192.168.1.111.
Updating the installed firmware
-------------------------------
The OpenWRT ramdisk image can be flashed directly from the Netgear UI.
The Image0 slot should be used in order to enable sysupgrade.
As with similar switches, changing the active boot partition can be
accomplished in U-Boot as follows:
1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
2. Run `setsys bootpartition {0|1}` to select the boot partition
3. Run `savesys` followed by `boota` to proceed with the boot process
Signed-off-by: Raylynn Knight <rayknight@me.com>
This was introduced to gmac2 and gmac3 in 57ea767a53 without fanfare.
There's no indication of why it was added to those devices, but not to
gmac0 or gmac1. It was probably an unintentional omission. It should be
present on all four gmac devices.
This property is considered by
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
stmmac_probe_config_dt.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
The Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301) has two Ethernet ports,
labeled MAIN and SECONDARY, connected to gmac2 and gmac1, respectively.
The standard probe order results in gmac1/SECONDARY being eth0 and
gmac2/MAIN being eth1. This does not match the stock firmware, is
contrary to user expectation, causes the wrong (high) MAC address to be
used in a bridged configuration (the default for this device), and makes
the gmac2/MAIN port unusable in the preinit environment (such as for
failsafe). Until a recent patch, gmac1/SECONDARY (eth0) was not even
usable.
This reorders the ports so that gmac2/MAIN is eth0, and the now-working
gmac1/SECONDARY is eth1. eth0 has the low MAC address and eth1 has the
high; when bridged, the bridge takes on the correct low MAC address.
This matches the stock firmware. The MAIN port is usable for failsafe
during preinit.
This device does not have a switch on board, so there's no possibility
to remap ports via switch configuration. "ip link set $interface name"
is used instead, during preinit before networking is configured.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
Unlike many ipq806x devices, Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301)
has no switch on board. Its two Ethernet ports are connected to Atheros
AR8033 PHYs. It is not appropriate to use fixed-link in this
configuration. Instead, configure the correct PHYs in the device tree
configuration to allow the at803x driver to load.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
On a Ubiquiti UniFi AC HD (ubnt,unifi-ac-hd, UAP-AC-HD, UAP301), a
forced speed on gmac1 is set in the QSGMII PCS_ALL_CH_CTL register,
presumably by the bootloader (4.3.28), preventing the interface from
being usable. The QSDK NSS GMAC driver takes care to clear the forced
speed in nss_gmac_qsgmii_dev_init
(https://source.codeaurora.org/quic/qsdk/oss/lklm/nss-gmac/tree/ipq806x/nss_gmac_init.c?h=nss
at d5bb14925861).
gmac1 is connected to the port on the device labeled SECONDARY, and is
currently eth0 but will be switched to eth1 by a subsequent patch. By
clearing the QSGMII PCS forced speed during dwmac initialization when
SGMII is in use, this port becomes usable.
This patch is upstreamable, and will be sent upstream after successful
testing in OpenWrt.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
The kernel image is too big now and the build fails.
WARNING: Image file zyxel_nbg6716-kernel.bin is too big: 4205404 > 4194304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In order to allow easily updating the bootloader on eMMC also provide
artifacts for that. Support for updating bootloader via TFTP will be
added to the loader CLI menu in a follow-up commit.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is possible to select CONFIG_MTD_PARSER_TRX on the mediatek now. Add
this option to the kernel configuration file.
Fixes: 58c5e25664 ("mediatek: support non standard trx magic values")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This partly reverts commit 20a924d2ae.
This commit broke the build of the Mediatek target with kernel 5.4, for
kernel 5.10 it is fine.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The spi-ath79 driver performs the chipselect by writing to dedicated
register in the SPI register block. So the GPIO numbers were not used.
Tested-on: Enterasys WS-AP3705i
Signed-off-by: David Bauer <mail@david-bauer.net>
All chipsets from AR7100 up to QCA9563 have three dedicated chipselect
lines for the integrated SPI controller. Remove the number of
chipselects from the platform data, as there is no need to manually set
this to a different value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the SPI_MASTER_GPIO_SS flag for the spi-ath79 driver. Otherwise,
the custom chipselect function is never called. This breaks hardware,
where the three dedicated chipselect lines are used instead of generic
GPIO pins.
Signed-off-by: David Bauer <mail@david-bauer.net>
This came up in an upstream commit: "
b1dd9bf688b0 "net: phy: broadcom: Fix RGMII delays for BCM50160 and BCM50610M"
The PHY driver entry for BCM50160 and BCM50610M calls
bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in
order to configuration appropriate clock delays on the PHY, fix that."
So the "rgmii" phy-mode has always been wrong, but went unnoticed since
the broadcom phy driver didn't push the delay settings to the chip.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The CLK125 output pin at the ethernet PHY is connected via capacitor to
GND and nowhere else. Disable it. Also tune the LED masks.
The MPP56 and MPP60 pins at the SoC are conected to the μPD720202 USB3.0
chip:
- MPP56: wired to PCIe CLKREQ# (out)
- MPP60: wired to PCIe RESET# (in)
Configure the pcie pinmux for these pins.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
These have long been obsolete. For reference, here's the Linux version where
each symbol has been dropped:
CONFIG_IP6_NF_QUEUE - 3.5
CONFIG_IP6_NF_TARGET_LOG - 3.4
CONFIG_IP_NF_MATCH_DSCP - 2.6.19
CONFIG_NF_CONNTRACK_IPV4 - 4.19
CONFIG_NF_CONNTRACK_IPV6 - 4.19
CONFIG_NF_CONNTRACK_RTCACHE - out-of-tree, superseded by flow offloading
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This kmod is similar to macvlan with the difference being that the
endpoints have the same mac address.
It is useful on cloud where only one mac address allowed on port,
where macvlan not works but ipvlan would.
One use case is where multiple IPs and gateways assign on one net port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.
This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.
This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.
The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.
This increases the size of an uncompressed kernel by less than 1 KB.
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The new EEE patch is accepted upstream, so backport it and replace the
current one.
Cc: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
This CFI patch was accepted upstream for 5.13. Move it away from under
ath79 and place under backports to be removed in due time.
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93
Signed-off-by: John Audia <graysky@archlinux.us>
Since support for SFP on the MikroTik RouterBOARD 922UAGS-5HPacD was
added by 4387fe00cb, the MAC addresses for eth0 (Ethernet) and eth1
(SFP) were swapped. This patch fixes the 02_network script to assign MAC
addresses correctly, so they match the label and the vendor's OS.
Tested on a RouterBOARD 922UAGS-5HPacD board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Commit f724a583dc updated the nand-rb4xx driver to the 5.10 testing
kernel, but forgot to add the new kernel config symbol it introduces to
the 5.10 config.
Fixes: f724a583dc ("ath79: mikrotik: update nand-rb4xx driver")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Generating the sdcard.img.gz file requires the initramfs/recovery
image to be present. Use the newly introduced 'append-image-stage'
build command to fix the ImageBuilder for the BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build the driver for the in-SoC AHCI SATA host as module, just like for
the other subtargets. No board requires booting off SATA, so we don't
need to have it built-in. All boards with SATA support already select
kmod-ata-ahci-mtk which provides the module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It's in backports-5.4, but it wasn't ever merged. Upstream followed another
approach, with flow offloading, which has much better performance. Drop this
obsolete patch and refresh the kernel patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Make sure all compression algorithms are enabled, for the time being, in order
not to break sysupgrade. In the future, we'd like to disable all except zstd, as
it's the best all-around performer.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
