Commit Graph

28585 Commits

Author SHA1 Message Date
Glen Lee
0250e4e4bc ipq806x: sync config-6.1 with latest kernel
Ran "make kernel_oldconfig" to generate

Signed-off-by: Glen Lee <g2lee@yahoo.com>
2023-09-24 18:12:30 +02:00
Elbert Mai
75ee5546e9 mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)
Ubiquiti U6+ is a dual-band WiFi 6 PoE access point.
It is a drop-in upgrade of the U6 lite.

Specifications
---

- SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz
- RAM: 256 MB DDR3-2133 RAM
- Flash: 16 MB SPI NOR and 4 GB eMMC
- LAN: 1x Gigabit Ethernet with 802.3af/at support
- WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6
- LEDs: 1x blue and 1x white
- Buttons: 1x reset button

Installation
---

1. Power device using a PoE injector or switch
2. Connect via Ethernet to the device with static IP 192.168.1.2
3. SSH into the device with password: ubnt

        $ ssh ubnt@192.168.1.20

4. Unlock kernel partitions for writing

        $ echo 5edfacbf > /proc/ubnthal/.uf

5. Confirm correct partitions

        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent
        PARTNAME=kernel0
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent
        PARTNAME=kernel1
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent
        PARTNAME=bs

6. Set and confirm bootloader environment

        $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt"
        $ fw_setenv bootcmd_real "run boot_openwrt"
        $ fw_printenv

7. Copy sysupgrade image to /tmp/openwrt.bin via scp
8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively

        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6
        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7

9. Ensure device boots from mmcblk0p6

        $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8

10. Reboot the device

        $ reboot

Signed-off-by: Elbert Mai <code@elbertmai.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-09-24 17:16:16 +02:00
Andreas Böhler
191da23551 ramips: fix Mercusys MR70X LAN port assignments
A bug report in the forum found that the MR70X lists four LAN ports in LuCI
while it has only three. This adds the device to the network setup file
to fix the issue.

Identified-by: Forum User "Lexeyko"
Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-24 17:09:26 +02:00
Kristian Skramstad
76e419288f ipq807x: add support for Netgear WAX620
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
  Use the header closest to LED 4 and 5.
  They are marked with a white stroke.
  TX RX GND, beginning from "4". 115200n8.

Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)

Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)

Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```

```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1.  Download the OpenWrt initramfs image. Copy the image to a TFTP server
2.  Connect to console on the AP, and connect the LAN port to your LAN
3.  Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4.  Set active_fw in env
    # setenv active_fw 1
5.  Transfer the initramfs image with TFTP
    # setenv serverip 192.168.1.10 (IP of TFTP server host)
    # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
    # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6.  Reboot and load the image
    # bootm
7.  SCP factory image to the AP
    # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8.  Connect to device using SSH (use the LAN port)
9.  Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
    Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
    # cat /proc/mtd (To check MTD partitions)
    # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
    # /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
    # reboot
```

Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-09-24 13:09:16 +02:00
Mathew McBride
f86415085b armsr: ensure kmod-fs-vfat is selected for mounting ESP
vfat support is needed to mount the EFI System Partition (ESP)
during sysupgrade. If it is not available, the sysupgrade process
will not complete

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-09-24 12:51:14 +02:00
John Audia
2368cafbd8 kernel: bump 6.1 to 6.1.55
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.55

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-24 12:45:34 +02:00
Sijia Huang
ab12a01cd7 ramips: add support for WAVLINK WL-WN573HX1
Hardware
--------

Specifications:
- Device: WAVLINK WL-WN573HX1 Outdoor AP
- SoC: MT7621AT
- Flash: 16MB
- RAM: 256MB
- Switch:1 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x STATUS (blue, configurable)
		1x LAN (green)

Product link:
https://www.wavlink.com/en_us/product/WL-WN573HX1.html

Signed-off-by: Sijia Huang <engineer31@win-star.com>
2023-09-24 12:36:52 +02:00
John Audia
e3559fb445
kernel: bump 6.1 to 6.1.54
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.54

Removed upstreamed:
	generic/backport-6.1/020-v6.3-02-UPSTREAM-mm-multi-gen-LRU-rename-lrugen-lists-to-lru.patch[1]
	ipq806x/patches-6.1/140-v6.5-hwspinlock-qcom-add-missing-regmap-config-for-SFPB-M.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.54&id=a73d04c460521e45f257d28d73df096e41ece324
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.54&id=e93bc372dbc0bde133c854c03502a95617041972

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-23 13:10:28 +02:00
John Audia
2bda536a3d
kernel: bump 6.1 to 6.1.53
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.53

Removed upstreamed:
	bcm53xx/patches-6.1/032-v6.6-0005-ARM-dts-BCM53573-Drop-nonexistent-usb-cells.patch[1]
	bcm53xx/patches-6.1/032-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[2]
	bcm53xx/patches-6.1/032-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[3]
	bcm53xx/patches-6.1/032-v6.6-0011-ARM-dts-BCM53573-Fix-Tenda-AC9-switch-CPU-port.patch[4]

All other patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=ee1d740374aa73fb32857685eb05167ad87458cf
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=ab5154ae26c446136827451e907db45d7b92a76f
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=f5ff6897094fa161be55786cb9e5d5b1bf7a9049
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.53&id=0ef736fec61422794c4a991d46c4ec212b01d8d1

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-23 13:10:28 +02:00
John Audia
915f69ec6c
config-6.1: disable CONFIG_VIDEO_CAMERA_SENSOR
Disable new ksym globally as it is unconditionally selecting symbols.
See: 7d3c7d2a29

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-23 13:10:24 +02:00
Daniel Golle
ce7209bd21 mediatek: add build for MT7981 RFB
Add build for the MTK3943 reference board for MT7981B+MT7976C.

**Hardware specification:**

 - SoC: MediaTek MT7981B 2x A53
 - Flash: various options
 - RAM: 256MB DDR3
 - Ethernet: 4 x 10/100/1000 Mbps via MT7531AE switch
        EITHER 1 x 10/100/1000 Mbps built-in PHY
            OR 1 x 10/100/1000/2500 Mbps MaxLinear GPY211C
 - Switch: MediaTek MT7531AE
 - WiFi: MediaTek MT7976C
 - Button: RST, WPS

**Flash instructions for SPIM-NAND:**
 - write *mt7981-rfb-spim-nand-preloader.bin to 'BL2' partition
 - write *mt7981-rfb-spim-nand-bl31-uboot.fip to 'FIP' partition
 - erase 'ubi' partition
 - reset board
 - create ubootenv and ubootenv2 UBI volumes in U-Boot
 - edit environment and set bootcmd, e.g.
   setenv bootconf 'config-1#mt7981-rfb-spim-nand#mt7981-rfb-mxl-2p5g-phy-eth1'
   setenv bootcmd 'ubi read $loadaddr fit; bootm $loadaddr#$bootconf'
 - load initramfs image via TFTP:
   setenv serverip 192.168.1.254
   setenv ipaddr 192.168.1.1
   setenv bootfile openwrt-mediatek-filogic-mediatek_mt7981-rfb-initramfs.itb
   saveenv ; saveenv
   tftpboot
   bootm $loadaddr#$bootconf
 - Now use sysupgrade to write OpenWrt firmware to flash.

SNFI-NAND, SPIM-NOR and eMMC all work very similar, a bootable SD card image
is also being generated. However, as the board I've been provided only comes
with SPIM-NAND all other boot media are untested.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-21 10:15:08 +01:00
Daniel Golle
9f62abbb60 kernel: serial: 8250_mtk: track busclk state to avoid bus error
UARTs not used as boot console are currently broken on some MediaTek
targets due to register access depending on the bus clock being enabled.
Add patch to make sure this dependency is always met.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-21 10:15:08 +01:00
David Bauer
8037417744 mpc85xx: correct WS-AP3715i eth LED assignment
Ethernet LED assignments were incorrectly swapped. Fix the assignment
logic so the correct LED is illuminated for the LAN LEDs.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-09-21 01:10:40 +02:00
Andreas Böhler
7354d17ff4
ipq4019: add support for ZTE MF282 Plus aka DreiTube
The ZTE MF282 Plus is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF286/MF287 but in the form factor
of the MF282.

Specifications
==============

SoC: IPQ4019
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 1x GBit LAN
LTE: ZTE Cat6
WiFi: 802.11a/b/g/n/ac SoC-integrated

MAC addresses
=============

LAN: from config
WiFi 1: from config + 1
WiFi 2: from config + 2

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x84000000 openwrt.bin
  bootm 0x84000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m9
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd9 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd9 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock9 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 9
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to the MF286R, it provides an RNDIS interface
and an AT interface.

Other Notes
===========

There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-20 14:29:20 +02:00
John Audia
ac422c9788
kernel: bump 5.15 to 5.15.132
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.132

Removed upstreamed:
	bcm53xx/patches-5.15/037-v6.6-0006-ARM-dts-BCM53573-Add-cells-sizes-to-PCIe-node.patch[1]
	bcm53xx/patches-5.15/037-v6.6-0007-ARM-dts-BCM53573-Use-updated-spi-gpio-binding-proper.patch[2]
	bcm53xx/patches-5.15/037-v6.6-0008-ARM-dts-BCM5301X-Extend-RAM-to-full-256MB-for-Linksy.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=b35f3ca1877e024887df205ede952863d65dad36
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=2840d9b9c8750be270fb1153ccd5b983cbb5d592
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.132&id=f086e859ddc252c32f0438edff241859c0f022ce

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-20 14:13:00 +02:00
Robert Marko
d6ac365e42
mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.

The same image can be used on both versions as U-Boot will enable the
switch node and disable the unused ethernet controller.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
Robert Marko
0b6d62c50b
generic: 6.1: backport support for Marvell 88E6361 switch
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
Robert Marko
39227de5e5
generic: 5.15: backport support for Marvell 88E6361 switch
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.

Since 5.15 doesnt have phylink_get_caps I had to modify the backport to
use the old mv88e6393x_phylink_validate instead.
I had to fixup one more instance of port_max_speed_mode as well that is not
present in 6.5.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
Andreas Böhler
053f8f92d1
ipq40xx: ZTE MF287 series: move to gpio-export for modem-reset GPIO
Turn the "gpio-restart" node into a "gpio-export" node for all MF287
variants, similar to the MF287 Pro. Unfortunately, there doesn't seem to be
a "power button blocker" GPIO for the MF287 and MF287 Plus, so a modem
reset always triggers a system reset.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-19 11:43:36 +02:00
Andreas Böhler
9c7578d560
ipq40xx: refactor ZTE MF287 series
The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-19 11:43:36 +02:00
Pascal Coudurier
5602665255
x86: add 6.1 testing kernel
Enable building with 6.1 as testing kernel

Compile-tested: x86_64, x86_generic, x86_legacy, x86_geode
Run-tested: x86_64, x86_generic (qemu), x86_legacy (qemu)

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:38 +02:00
Pascal Coudurier
af52f72f94
x86: refresh kernel configs for 6.1
refresh and add missing symbols for target and subtargets

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:37 +02:00
Pascal Coudurier
2e89ef1824
x86: copy 5.15 configs to 6.1
Copy 5.15 configs to 6.1 as a starting point

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:36 +02:00
Pascal Coudurier
b2c0e75c25
x86: refresh patches for 6.1
Removed upstream merged patch:
113-v5.21-platform-x86-pmc_atom-Add-Lex-3I380NX-industrial-PC-.patch

Manually rebased:
103-pcengines_apu6_platform.patch

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:36 +02:00
Pascal Coudurier
f23015b18e
x86: copy 5.15 patches to 6.1
Copy existing patches from 5.15 to 6.1

Signed-off-by: Pascal Coudurier <coudu@gmx.com>
2023-09-19 11:38:36 +02:00
Zoltan HERPAI
6bf8193b25 sunxi: add support for Bananapi P2 Zero
CPU:     Allwinner H2+ quad-core Cortex-A7 @ 1.2GHz
Memory:  512Mb DDR3
Storage: SDcard, 8GB eMMC
Network: 10/100M ethernet, optional PoE support, Ampak AP6212 wifi + BT
USB:     1x USB 2.0 OTG
Other:   40-pin expansion header, mini-HDMI

Flashing instructions:
  Standard sunxi SD card installation procedure - copy image to SD card,
  insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-18 18:15:21 +02:00
Christian Marangi
c64a5d122f
sunxi: refresh kernel patches
Refresh kernel patches for sunxi target.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-09-18 13:44:50 +02:00
Chukun Pan
9889de3397
ipq40xx: add support for YYeTs LE1
Hardware Highlights:
SoC:	  Qualcomm IPQ4019 717 MHz
RAM:	  512M NT5CC256M16ER-EK
Flash:    32M SPI NOR MX25L25635F
WIFI1:    2.4 GHz 2T2R integrated
WIFI2:    5 GHz 2T2R integrated
Ethernet: QCA8075 (4x LAN, 1x WAN)
LEDS:     power, wlan2g, wlan5g, usb
USB:      1x 3.0
Button:   Reset

Installation:
  Upload factory.bin in stock firmware's upgrade
  page, and this will take a few minutes.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-09-18 12:20:04 +02:00
Andreas Böhler
a9cc3708e0
ipq40xx: fix image building for ZTE MF287 series
For the ZTE MF287 series, a special recovery image is built. The Makefile
worked fine on snapshot, but created corrupt images on the 23.05 images.
By using the appropriate variable, this should be fixed.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-09-18 11:49:37 +02:00
Zoltan HERPAI
12584395dc sunxi: add support for H616 SoC and Orangepi Zero 2
Specifications:

SoC:     Allwinner H616 @ 1.5 Ghz
DRAM:    1Gb LPDDR3
Power:   5V USB-C
Video:   HDMI (Type 2.0A - micro)
Network: 10/100/1000Mbps Ethernet (Realtek RTL8211F), AW859A BT+wifi
Storage: microSD / 2Mb SPI flash
USB:     1 USB2.0 Host
Debug    Serial UART

Flashing instructions:
  Standard sunxi SD card installation procedure - copy image to SD card,
  insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-18 00:08:19 +02:00
Max Qian
794349a28a ramips: RT1800: fix invalid octal number error
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.

Signed-off-by: Max Qian <public@maxqia.com>
2023-09-17 13:52:55 -07:00
Robert Marko
98bad1b4fc ipq40xx: 6.1: add missing secure QFPROM symbol
Kernel config for 6.1 on ipq40xx is missing the config for
CONFIG_NVMEM_QCOM_SEC_QFPROM which them makes the build stop with a prompt.

Symbol is there in 5.15 config but 6.1 config was based of a version that
does not yet have it set as it was introduced after the 6.1 PR.

So, disable CONFIG_NVMEM_QCOM_SEC_QFPROM to fix building on 6.1.

Fixes: 825cfa4e36 ("ipq40xx: 6.1: refresh kernel config")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 22:19:23 +02:00
Robert Marko
b50827fb10
ipq40xx: add 6.1 as testing kernel
Allow selecting 6.1 as the testing kernel.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:25 +02:00
Robert Marko
825cfa4e36
ipq40xx: 6.1: refresh kernel config
Refresh the kernel config via make kernel_menuconfig.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:24 +02:00
Robert Marko
cd9c721124
ipq40xx: 6.1: use latest DSA and ethernet patches
This pulls-in the latest version of qca8k based IPQ4019 driver as well as
the latest version of IPQESS that was sent upstream.

Both qca8k and IPQESS have been improved and cleaned up compared to current
version of patches.

PSGMII PHY mode and missing reset have been upstreamed and will be in
the kernel 6.6.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-09-17 21:00:24 +02:00
Robert Marko
4c010932a5
ipq40xx: 6.1: adapt and refresh patches
Adapt and refresh patches to apply.

DSA and ethernet driver patches are dropped as they will be replaced with
the latest version that was sent upstream.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:24 +02:00
Robert Marko
3d6d8bcd8f
ipq40xx: qca807x: adapt for 6.1
Kernel 6.1 has changed format of sfp_parse_support(), so lets adapt to
those changes so it works on newer kernels as well.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:23 +02:00
Robert Marko
bd242a42a6
ipq40xx: copy 5.15 patches and config to 6.1
Copy the 5.15 patches and config as a base for 6.1 support.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:23 +02:00
Robert Marko
70dfb696c0
ipq40xx: update ESS reset patch with pending upstream
Use the split version of ESS reset patch that was sent upstream.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:23 +02:00
Robert Marko
9bfbdfa778
ipq40xx: move DSA and ethernet driver to 5.15 specific directory
As a preparation to move to 6.1, we need to move the DSA and ethernet
drivers to a 5.15 specific directory as 6.1 will use the latest patchset
that was sent upstream which is too hard to backport to 5.15.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-09-17 21:00:22 +02:00
Matthijs Kooijman
d2ce3a61aa
ath79: fix packetloss on some WLR-7100
On some WLR-7100 routers, significant packet loss was observed. This is
fixed by configuring a delay on the GMAC0 RXD and RXDV lines.

The values used in this commit are copied from the values used by the
stock firmare (based on register dumping).

Out of four test routers, the problem was consistently observed on two.
It is unclear what the relevant difference is exactly (the two working
routers were v1 001 with AR1022 and v1 002 with AR9342, the two broken
routers were both v1 002 with AR1022). All PCB routing also seems
identical, so maybe there is some stray capacitance on some of these
that adds just enough delay or so...

With this change, the packet loss disappears on the broken routers,
without introducing new packet loss on the previously working routers.

Note that the PHY *also* has delays enabled (through
`qca,ar8327-initvals`) on both RX and TX lines, but apparently that is
not enough, or it is not effective (registers have been verified to be
written).

For detailed discussion of this issue and debug history, see
https://forum.openwrt.org/t/sitecom-wlr-7100-development-progress/79641

Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
2023-09-17 16:39:10 +02:00
Zoltan HERPAI
863444f9cb sunxi: use kernel 6.1 as default
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-16 22:27:17 +02:00
Roger Pueyo Centelles
8486c677b8 ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite)
This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as
hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one
with PoE in. The device was already supported by the ar71xx target.

Specifications:
 - SoC: Qualcomm Atheros QCA9533
 - Flash: 16 MB SPI NOR
 - RAM: 64 MB
 - Ethernet: 4x 10/100 Mbps LAN, 1x 10/100 Mbps WAN (PoE in)
 - LEDs: 5x Ethernet port activity (green), 1x user (green)
 - Buttons: 1x reset

 See https://mikrotik.com/product/RB750r2 for more details.

Not working:
 - Serial port (already not working in ar71xx)

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Only the
 "Internet" port will ask for an initramfs image. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2023-09-16 12:49:26 +02:00
Thomas Makin
3121bf4f13
ipq40xx: add support for Netgear RBX40
This adds support for the RBR40 and RBS40 (sold together as RBK40),
two netgear routers identical to SRR60/SRS60 in all but antennae (and
hardware id). See 2cb24b3f3c for details.

Signed-off-by: Thomas Makin <halorocker89@gmail.com>
2023-09-16 12:08:03 +02:00
Brian Norris
7b78a19e6a ipq806x: Correct OnHub sysupgrade config logic
There's a typo in here: board_name is a function, not a variable. This
issue was pointed out on the OpenWrt forum.

Closes: #13409

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-09-12 23:36:30 +02:00
Aviana Cruz
46d673033b
ramips: add support for mtk eip93 crypto engine
Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.

Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Co-authored-by: Richard van Schagen <vschagen@icloud.com>
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-09-12 14:57:54 +02:00
Jonas Gorski
09d13cd8d8 x86: geode: fix hwrng register accesses
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.

To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.

Closes #13417.

Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2023-09-11 21:34:16 +02:00
Daniel Golle
3b86c1f929 kernel: backport two fixes for MediaTek Ethernet driver
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-11 14:09:48 +01:00
Piotr Dymacz
f1aaa267f0 ramips: add support for ALFA Network AX1800RM
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.

Specifications:

- SOC:      MT7621A (880 MHz)
- DRAM:     DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash:    16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi:    2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
            (MT7905DAN doesn't support background DFS scan/BT)
- LED:      6x green, 1x green/red
- Buttons:  2x (reset, WPS)
- Antenna:  4x external, non-detachable omnidirectional
- UART:     1x 4-pin (2.54 mm pitch, J4, not populated)
- Power:    12 V DC/1 A (DC jack)

MAC addresses:

LAN:     00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN:     00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz:   00:c0:ca:xx:xx:4c (factory 0xa)

Flash instructions for web-based U-Boot recovery:

1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.

The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:

1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
   in forced mode, without preserving settings: 'sysupgrade -n -F ...'.

Other notes:

If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2023-09-11 11:41:57 +02:00
David Bauer
7f54d9ba1a Revert "ath79: use kernel 6.1 as default"
This reverts commit c94383de01.

THis commit was not meant to be pushed to main yet.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-09-09 08:42:50 +02:00
John Audia
5294b358aa kernel: bump 6.1 to 6.1.52
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.52

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-09 02:15:15 +02:00
Tomasz Maciej Nowak
eac1928430 mvebu: cortexa72: enable USB PHY
Since kernel 5.13 this is needed to enable USB ports on all devices in
subtarget. Previously TF-A and COMPHY driver might have set up this PHY,
but not anymore.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
2023-09-08 23:49:00 +02:00
Tomasz Maciej Nowak
8e0d43d569 mvebu: refresh 6.1 configs
This should be a part of kernel major bump. Fortunately it didn't stall
compilation, so no fixes tag.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2023-09-08 23:49:00 +02:00
Patricia Lee
907e9e0bd3 mediatek: add support for Cetron CT3003
**Hardware specification:**

- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
  | Layout:   |
  | :-------- |
  | <Antenna> |
  | VCC       |
  | GND       |
  | Tx        |
  | Rx        |

**Flash instructions:**

1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.

**Notes:**

If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.

Signed-off-by: Patricia Lee <patricialee320@gmail.com>
2023-09-08 23:17:26 +02:00
John Audia
58bb5e147a kernel: bump 5.15 to 5.15.131
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.131

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-08 21:24:48 +02:00
David Bauer
c94383de01 ath79: use kernel 6.1 as default
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-09-08 21:00:26 +02:00
Shiji Yang
aee2af0f74 ath79: enable variable sector size erasure for generic subtarget
Make use of minor sector size (4k) erasure on supported flash chips
to improve spi read/write performance.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-09-08 18:06:30 +02:00
Shiji Yang
7ba69a94f9 ath79: backport gpio immutable irq_chip support
This patch converts the driver to immutable irq-chip, which can
silence some gpio warnings.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-09-08 18:06:30 +02:00
Shiji Yang
54758cf24b ath79: ignore the abused interrupt-map on PCIe node
ath79 PCIe interrupt controller has stopped working correctly. This
is because the DT exposing a non-sensical interrupt-map property,
and their drivers relying on the kernel ignoring this property[1].

This patch fixes the PCIe init error:
ath9k 0000:00:00.0: of_irq_parse_pci: failed with rc=-14

Notice:
This is just a workaround, not a fix. PCIe driver and related dts
node need to be rewritten.

[1] https://lore.kernel.org/all/20211201114102.13446-1-maz@kernel.org/

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-09-08 18:06:30 +02:00
Shiji Yang
7189b45784 ath79: fix ethernet driver build errors on kernel 6.1
Some net APIs have changed on the new kernel. Update them to fix
compile errors.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-09-08 18:06:30 +02:00
Shiji Yang
5f59d28bc3 ath79: refresh patches and configs to introduce kernel 6.1 support
All kernel configs are refreshed by
'make kernel_oldconfig CONFIG_TARGET=target' and
'make kernel_oldconfig CONFIG_TARGET=subtarget'.

upstreamed patches:
010-v5.17-spi-ar934x-fix-transfer-and-word-delays.patch
011-v5.17-spi-ar934x-fix-transfer-size.patch
020-v5.18-spi-ath79-Implement-the-spi_mem-interface.patch
030-v5.18-ath79-add-support-for-booting-QCN550x.patch

build and run tested on:
ath79/generic/ar7241
ath79/generic/qca9563
ath79/nand/ar9344

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-09-08 18:06:30 +02:00
Shiji Yang
d9a9caf352 ath79: copy patches and kernel config from 5.15 to 6.1
This is preparation for kernel 6.1 support.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-09-08 18:06:30 +02:00
Shiji Yang
c60dd7bef9 ath79: rename and sort patches by OpenWrt naming rules
The patches in the ath79 target have not been sorted for a long time
and they are very chaotic now. This patch sorts them again according
to the OpenWrt naming rules[1], so that we can better manage them.

[1] https://openwrt.org/docs/guide-developer/toolchain/use-patches-with-buildsystem#naming_patches

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-09-08 18:06:30 +02:00
Shiji Yang
496280ef4e ath79: add missing symbols by refreshing kernel configs
Some symbols are outdated or missing due to daily kernel bumps. It's
better to re-add them. All configs are automatically refreshed by
'make kernel_oldconfig CONFIG_TARGET=taget' and
'make kernel_oldconfig CONFIG_TARGET=subtarget'

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-09-08 18:06:30 +02:00
Rafał Miłecki
703d667a0c kernel: switch back to fw_devlink=permissive
This reverts commit 5356462ce5.

Kernel switching to fw_devlink=on as default broke probing some devices.
Revert it until we get a proper fix.

It seemed that mtd OF_POPULATED hack resolved probing issues but
apparently not all of them. We got reports about reading MAC using NVMEM
not working and USB controllers not working.

Ref: #10232
Fixes: #13412
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-09-05 16:05:32 +02:00
Chen Minqiang
36746893ac mediatek: fix the name of buswidth to bus-width
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.

[1] Documentation/devicetree/bindings/spi/spi-controller.yaml

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2023-09-05 15:40:43 +08:00
Jayantajit Gogoi
1b15cb21db rockchip: add support for Radxa ROCK Pi E
This adds support for Radxa ROCK Pi E, rockchip rk3328 board.

Specification:

- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
    1 x 10/100/1000M Ethernet
    1 x 10/100M Ethernet
- Storage:
    1 x MicroSD Slot
    1 x eMMC Module Slot
- USB Host/OTG:
    1 x USB3.0 Type A HOST
    1 x USB2.0 HOST (40-pin pin-header)
- Wireless
    RTL8723DU/RTL8821CU
- Debug Serial:
    1500000 baud at UART2 ( 40-pin pin-header)
- Power Supply:
    Type-C 5V
    Optionally PoE

Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card

Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
2023-09-05 00:20:51 +05:30
Felix Fietkau
77c45ddd86 kernel: backport support for renaming netdevs while up
Will be used in upcoming hostapd changes

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-04 15:29:35 +02:00
Thomas Bong
8554a4a7e3 ipq40xx: compress kernel for Magic 2 WiFi next
The bootcmd limits the kernel to 4 MiB which is
exceeded when using Device/FitImage. Device/FitzImage
reduces the size to around 3 MiB.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
2023-09-03 23:11:51 +02:00
Thomas Bong
838bb0c03f ipq40xx: convert devolo Magic 2 WiFi next to DSA
Renamed the interfaces to match the other devices.
Name the interface connected to the builtin G.hn chip 'ghn'.
This might toggle at runtime while the G.hn chip is in the
bootloader.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
2023-09-03 23:11:40 +02:00
INAGAKI Hiroshi
5c65224d8f mvebu: add reset delays of PHYs for Fortinet FortiGate 50E
Add reset-(de)assert-us to ethernet PHYs on Fortinet FortiGate 50E to
solve instability after HW resetting of PHYs. (ex.: restarting "network"
service, etc...)

Fixes: #13391
Fixes: 102dc5a625 ("mvebu: add support for Fortinet FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-03 22:59:39 +02:00
Hank Moretti
02214ab8dc mediatek: fix sysupgrade error for WR30U
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.

It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-09-01 23:45:47 +02:00
John Audia
d1ac7230d0 kernel: bump 6.1 to 6.1.50
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.50

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod, ipq806x/R7800
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod, ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-01 21:01:08 +02:00
John Audia
1db566b692 kernel: bump 5.15 to 5.15.129
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.129

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-09-01 20:34:16 +02:00
Felix Fietkau
c5b7be8316 kernel: allow adding devices without hw offload to a hw flowtable
This allows supporting a mix of devices with or without hw offloading support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-01 12:43:10 +02:00
Rafał Miłecki
bcd76dc7d8 bcm53xx: store a copy of NVRAM content in NVMEM driver
This stops NVMEM driver from using MMIO access past booting and messing
with NAND controller state.

Link: https://forum.openwrt.org/t/asus-rt-ac88u-hw-a6-broken-in-22-03-3/147882
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-09-01 11:37:16 +02:00
Daniel Golle
a8cbee8e2d mediatek: mt7622: set DEVICE_DTC_ADDR for BPi-R64
Relocating the device tree is required for being apply to apply
device tree overylay at boot.

Fixes: 34bb33094a ("mediatek: use updated device tree overlay mechanism for BPi-R64")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-31 19:22:15 +01:00
Rafał Miłecki
79283e8fb5 kernel: add unset CONFIG_INPUT_IBM_PANEL symbol to config-6.1
This symbol was added by commit 2e6f34faa7e0 ("Input: Add IBM Operation
Panel driver") to v6.1. It depends on I2C so it's available to limited
amount of targets. It needs to be specified thought to allow kernel
configuration.

For bcm53xx this fixes:
IBM Operation Panel driver (INPUT_IBM_PANEL) [N/m/?] (NEW)

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2023-08-31 09:13:00 +02:00
Rafał Miłecki
52c365f055 kernel: backport v6.6 nvmem changes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-08-31 00:49:29 +02:00
Mathew McBride
abc536f547 kernel: ensure VFIO related suboptions are disabled
These suboptions (PLATFORM, FSL_MC and MLX5_VFIO_PCI)
may be prompted for when VFIO is enabled, regardless of
architecture.

These are not related to the main vfio use case
(passthrough of PCIe devices)

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-29 23:41:05 +02:00
Daniel Golle
8f5986355c mediatek: filogic: remove stray quote
When adapting the network configuration for MT7988 RFB a stray quote
was left in a script. Remove it to fix generating the default network
configuration.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 21:54:02 +01:00
Daniel Golle
f631c7bbb1 generic: sync MediaTek Ethernet driver with upstream
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Daniel Golle
a0f4eadf6a mediatek: add support for Ubiquiti UniFi 6 LR v3
Some recent models of the Ubiquiti Networks UniFi 6 LR access point
come with a RealTek RTL8211FS 1000M/100M/10M PHY instead of the
Aquantia AQR112 2500M/1000M/100M/10M PHY used in both v1 and v2. Add
build for this variant so we can support Ethernet with the PHY.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Daniel Golle
035a88ae55 mediatek: generate bootloader artifacts for mt7988_rfb
Switch to OpenWrt uImage.FIT bootmethod and include various bootloader
artifacts with the generated binaries.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Daniel Golle
3ef8760e87 mediatek: improve mt7981.dtsi
* re-factor WED components to boot fine also on limited loaders
 * add LEDs of integrated GE PHY

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 13:55:38 +01:00
Daniel Golle
9f8fde216d mediatek: filogic: improve pinctrl drivers
Set correct pull-type data and add additional uart groups for MT7981.
Assign functions to configure pin bias for MT7986.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 13:55:38 +01:00
Daniel Golle
2544dc34f2 mediatek: i2c: mt65xx: allow optional pmic clock
Using the I2C host controller on the MT7981 SoC requires 4 clocks to
be enabled. One of them, the pmic clk, is only enabled in case
'mediatek,have-pmic' is also set which has other consequences which
are not desired in this case.

Allow defining a pmic clk even in case the 'mediatek,have-pmic' propterty
is not present and the bus is not used to connect to a pmic, but may
still require to enable the pmic clock.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 13:55:38 +01:00
Daniel Golle
69a498f953 mediatek: re-add missing patch for Linux 6.1
The patch was wrongly tagged as being part of Linux 6.0 even though it
was only committed with Linux 6.2 and hence needs to be backported for
Linux 6.1.

Fixes: fa79baf4a6 ("generic: copy backport, hack, pending patch and config from 5.15 to 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 13:55:38 +01:00
Daniel Golle
06a150aed7 mediatek: re-add dropped properties on BPi-R3
Unfortunately some device tree properties have slipped under the table
when switching from our downstream device tree.

Bring back 3W power for SFP cages and restore thermal trip points to
make sense again.

Fixes: 7a0ec001ff ("mediatek: sync MT7986 device trees with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 13:55:38 +01:00
Linus Walleij
ef76b6ff3e bcm53xx: Add support for D-Link DIR-890L
The DIR-890L is very similar to DIR-885L, but has both USB2
and USB3. The signature for the wrgac36 board was copied from
DD-Wrt.

The DIR-890L bootstrap will only load the first 2 MB after
the SEAMA header in the NAND flash, uncompress it with LZMA
and execute it. Since the compressed kernel will not fit in
2 MB we have a problem. Solve this by putting a LZMA
compressed U-Boot into the first 128 KB of the flash
followed by the kernel. The bootstrap will then uncompress
and execute U-Boot and then we let U-Boot read the kernel
from flash and execute it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-08-28 08:13:39 +02:00
Brian Norris
1611c21ac6 ipq806x: onhub: Enable adm_dma node
One of our SPI devices references this node, but we never enabled it.
This clutters up probe deferral logs.

(NB: this SPI device still doesn't have a real driver, so it's just here
for documentation and/or tinkering.)

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-08-27 22:47:02 +02:00
Brian Norris
9ea5487ea5 ipq806x: chromium: Disable kernel's CONFIG_QCOM_SPM
The qcom spm driver is currently broken for IPQ8064 OnHub devices on
kernel 6.1, such that it hangs the system when booting, much to the
consternation of users. This is especially bad as these devices don't
yet have a fully-supported release branch, and are still sometimes
landing on snapshot builds.

OnHub devices have their own kernel config, so it's not that wide of an
impact to disable this.

I haven't fully gotten to the bottom of this, but:

(a) The vendor kernel didn't have any SPM driver at all, and didn't
    utilize cpuidle.
(b) The device tree has never included any (non-disabled) cpuidle
    states, so even when this driver was present on 5.15 (last
    known-working kernel), it didn't actually do anything -- it bailed
    early, before ever doing any SPM initialization.
(c) Refactoring in Linux 5.16 [1] caused the SPM driver to be activated
    unconditionally, including setting us into standby mode
    (PM_SLEEP_MODE_STBY) by default.

Removing the one PM_SLEEP_MODE_STBY line from drivers/soc/qcom/spm.c
seems to fix the problem, but that isn't much different than simply
disabling the driver, so I go with that for now.

I also disable CONFIG_ARM_QCOM_SPM_CPUIDLE, becuase it 'select's
QCOM_SPM.

NB: it's possible there's some other deeper root cause involved in here.
For one, I notice that CPU hotplug (e.g., echo 0 >
/sys/devices/system/cpu/cpu1/online, echo 1 > ...) doesn't work right
either. Perhaps there's some mismatch on upstream Linux qcom-scm
behavior and the old boot firmware used for these systems? It wouldn't
be the first time, as we've had some similar incompatibilities on the
next generation of these devices, Google WiFi [2].

[1] Commit 60f3692b5f0b ("cpuidle: qcom_spm: Detach state machine from
    main SPM handling")
[2] [RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
    https://lore.kernel.org/linux-arm-kernel/20200913201608.GA3162100@bDebian/

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-08-27 22:47:02 +02:00
Antonio Flores
f0138de3e5 rockchip: add support for PINE64 ROCK64
This add support for PINE64 ROCK64, rockchip rk3328 board.

Specifications:

 4 x ARM Cortex A53 cores @ 1.5 GHz
 ARM Mali 450 MP2 GPU
 LPDDR3 RAM (up to 4GB)
 Gigabit Ethernet
 Micro SD Slot
 eMMC module slot
 SPI Flash 128Mbit
 4K digital video out
 2x USB 2.0 Host
 1x USB 3.0 Host
 PI-2 bus
 PI-P5+ bus
 IR R/X port
 Real Time Clock (RTC) port
 Power Over Ethernet (POE) (when using optional HAT module)
 A/V jack
 Power, Reset and Recovery buttons
 3.5mm barrel power (5V 3A) port

To install write image to the sd using dd (dd if=*.img of=/*)

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2023-08-27 19:20:11 +02:00
Rani Hod
a4eb1ea331 ramips: add support for D-Link DRA-1360
The DRA-1360 rev A is a wall-plug AC1300 repeater.
Hardware is identical (same FCC ID, black case instead of white)
to D-Link DAP-1620 rev B, which is already supported, but a
different model name, revision, and hardware ID are needed.
Thus, the bulk of the DAP-1620 device tree is extracted to a
common dtsi included by the two models' device trees.

Repeating specs and installation instructions from e4c7703:
(note that the RAM size mentioned there was incorrect, oops)

Specs:
- SoC: MT7621AT (880MHz dual-core MIPS1004Kc)
- Memory: 128 MiB RAM, 16 MiB NOR SPI
- WiFi: MT7615DN 2x2 802.11n + 2x2 802.11ac (DBDC)
- Ethernet: 1 RJ45 port 10/100/1000
- Power/status LED: red+green
- LED RSSI bargraph: 2x green, 1x red+green

Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
  (pings are ignored, it listens only for http)
- Upload factory.bin, confirm flashing
  (seems to work best with Chromium-based browsers)

Revert to OEM firmware:
- tail -c+117 DRA1360A1_FW112B03.bin | \
  openssl aes-256-cbc -d -md md5 -out decrypted.bin \
  -k c471706398cb147c6619f8a04a18d53e9c17ede8
- flash decrypted.bin via D-Link Web Recovery

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-08-27 19:13:36 +02:00
John Audia
e80a387517 kernel: bump 5.15 to 5.15.128
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.128

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-27 16:15:22 +02:00
Fabian Bläse
b22d382ae4 ipq40xx: re-add label MAC address for FritzBox 4040
The MAC address of the GMAC is contained inside the CWMP-Account
number on the label.

The label MAC address alias was defined previously, but it has been
removed with the switch to IPQESS / DSA.

Restore the label MAC address alias.

Fixes: 27b441cbaf ("ipq40xx: drop ESSEDMA + AR40xx DTS nodes")
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2023-08-27 16:09:11 +02:00
Mathew McBride
8b1cc1582a x86: remove built-in vhost-net driver
This is now available as a kmod package (kmod-vhost-net).

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-26 14:08:10 +02:00
John Audia
4b3e3c3fd7 kernel: bump 6.1 to 6.1.47
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.47

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-26 00:07:16 +02:00
David Bauer
6dc0675e5b mediatek: enable NMBM remapping for NWA50AX Pro UBI
Don't skip remapping of the UBI area for the ZyXEL NWA50AX Pro. This is
due to the kernel being loaded from the UBI partition by U-Boot.

Link: https://github.com/openwrt/openwrt/pull/13335

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-25 21:42:31 +02:00
Zoltan HERPAI
f01982ec0b sunxi: add testing kernel 6.1
Compile-tested: all targets
Runtime-tested:
 - Cortex-A53: Pine64+
 - Cortex-A7:  Bananapro, Orange Pi 2
 - Cortex-A8:  pcDuino v2

Patches refreshed.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-08-24 18:52:06 +02:00
Zoltan HERPAI
939d4d0b70 sunxi: copy patches from 5.15 to 6.1
To start the migration, we copy the patches from 5.15 to 6.1.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-08-24 18:51:51 +02:00
Shiji Yang
12f53724c6 ath79: fix first reboot issue on Netgear WNDR4300 v2 and WNDR4500 v3
From the Netgear u-boot GPL code[1]. Bootloader always unconditionally
marks block 768, 1020 - 1023 as bad blocks on each boot. This may lead
to conflicts with the OpenWrt nand driver since these blocks may be good
blocks. In this case, U-boot will override the oob of these blocks so
that break the ubi volume. The system will be damaged after first reboot.
To avoid this issue, manually skip these blocks by using "mtd-concat".

[1] https://www.downloads.netgear.com/files/GPL/EX7300v2series-V1.0.0.146_gpl_src.tar.bz2.zip

Fixes: https://github.com/openwrt/openwrt/issues/8878
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-08-24 00:04:38 +02:00
Shiji Yang
0f9b8aa3f5 ath79: rework Netgear nand devices image recipe
In Netgear u-boot GPL code, nand devices uses this formula to locate the
rootfs offset.

offset = (((128 + KERNEL_SIZE) / BLOCK_SIZE) + 1) * BLOCK_SIZE;

Howerver, WNDR4500 source code incorrectly define the nand block size to
64k. In some cases, it causes u-boot can't get the correct rootfs offset,
which result in boot failure. This patch workaround it by padding kernel
size to (128k * n - 128 - 1). The additional char '\0' is used to ensure
the (128 + KERNEL_SIZE) can't be divided by the BLOCK_SIZE.

Fixes: https://github.com/openwrt/openwrt/issues/13050
Fixes: 3c1512a25d ("ath79: optimize the firmware recipe for Netgear NAND devices")
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-08-24 00:04:38 +02:00
David Bauer
4c0fdad7ea mediatek: enable NWA50AX Pro eth LEDs
Enable the ethernet LED's on the ZyXEL NWA50AX Pro to show link-state as
well as activity.

Both LED's are configured pulsing.

AMBER | 10/100
GREEN | 1000
A+G   | 2500

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-22 13:37:27 +02:00
Stefan Agner
4af06aaf33 mediatek: filogic: wax220: cleanup device tree
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2023-08-22 13:37:27 +02:00
Stefan Agner
fa9d977f97 mediatek: filogic: wax220: support factory image
Enable building a factory image which can be flashed through the OEM
firmware's web interface. It seems that the web interface requires a
minimum file size of 10MiB, otherwise it will not accept the image.

The update image is a regular sysupgrade tarball packed in a Netgear
encrypted image. The Netgear encrypted image is the same as used in
WAX202 or WAX206, including the encryption keys and IV.

This adds a script which creates the rootfs_data volume on first
startup. This is required since the OEM firmware's sysupgrade scripts
do not create such a paritition. Note that any script ordered after
70_initramfs_test will not get executed on initramfs. Hence this new
script 75_rootfs_prepare won't create the rootfs_data volume when
using the recovery initramfs.

Also, this deletes the kernel_backup and rootfs_backup volumes in case
we have to create the rootfs_data volumes. This makes sure that
OpenWrt is the actual backup firmware instead of the stock firmware.

References in WAX220 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX220-V1.0.2.8-gpl-src.tar.gz

* package/base-files/files/lib/upgrade/nand.sh:186
  Creation of rootfs_data is disabled

* Uboot-upstream/board/mediatek/common/ubi_helper.c
  Automatic creation of UBI backup volumes

Signed-off-by: Stefan Agner <stefan@agner.ch>
2023-08-22 13:37:27 +02:00
David Bauer
c35ff41ccc mediatek: add missing packages for Acer Predator W6
Add missing packages for creating the overlay filesystem.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-22 12:24:34 +02:00
INAGAKI Hiroshi
ac68fbf526 ramips: add support for I-O DATA WN-DEAX1800GR
I-O DATA WN-DEAX1800GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on MT7621A.

Specification:

- SoC         : MediaTek MT7621A
- RAM         : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash       : RAW NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN        : 2.4/5 GHz (MediaTek MT7915)
- Ethernet    : 5x 10/100/1000 Mbps
  - Switch    : MT7530 (SoC)
- LEDs/Keys   : 6x/3x
- UART        : through-hole on PCB (J2)
  - assignment: 3.3V, GND, TX, RX from "1" marking
  - settings  : 115200n8
- Power       : 12 VDC, 1 A

Flash instruction using initramfs-factory image:

1. Boot WN-DEAX1800GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs-factory.bin image and click update
   ("更新") button to perform firmware update
4. On the initramfs image, perform sysupgrade with the
   squashfs-sysupgrade.bin image
5. Wait ~120 seconds to complete flashing

Note:

- This device has 2x OS images on the flash storage. In this support,
  the first one will be used.

Warning:

- Do not use "saveenv" command on U-Boot CLI.
  This device has wrong u-boot-env data. The actual length of individual
  env data installed to the device is 0x1000 (4 KiB), but installed
  U-Boot requires 0x20000 (128 KiB). So U-Boot determines the data is
  invalid. Then, if you perform saving environment data with saveenv on
  U-Boot CLI, installed env data will be overwritten with too few
  default values without individual values (SSID, password, MAC
  addresses, etc...).

MAC addresses:

LAN    : 50:41:B9:xx:xx:F4 (Config, ethaddr (text))
WAN    : 50:41:B9:xx:xx:F6 (Config, wanaddr (text))
2.4 GHz: 50:41:B9:xx:xx:F4 (Config, rmac (text) / Factory, 0x4 (hex))
5 GHz  : 50:41:B9:xx:xx:F5 (none)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-08-20 01:26:15 +02:00
INAGAKI Hiroshi
9088b5445f ramips: improve sysupgrade helpers for I-O DATA devices
I-O DATA devices manufactured by MSTC (MitraStar Technology Corp.)
have some important flags for booting, "bootnum" and "debugflag".
The almost devices have both flags but some devices have only
"bootnum" flag.
So optimize helper functions in iodata.sh to set each flags.

- both:
  - WN-AX1167GR2
  - WN-AX2033GR
  - WN-DX1167R
  - WN-DX1200GR
  - WN-DX2033GR

- "bootnum" only
  - WN-DEAX1800GR

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-08-20 01:26:15 +02:00
Bjørn Mork
6cc14bf66a filogic: support Telenor branded ZyXEL EX5700
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.

Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
  cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
  back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree

Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
  unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
  refuses to boot if it doesn't. The chosen "rootfs" volume must contain
  a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
  variable to the label mac.  But "factoryparams" does not always
  exist.  Instead there is a "RIP" volume containing all the factory
  data.  Copying the "RIP" volume to  "factoryparams" will fix this

Hardware
--------
SOC:   MediaTek MT7986
RAM:   1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI:  Mediatek MT7986 802.11ax 5 GHz
       Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH:   MediaTek MT7531 Switch + SoC
       3 x builtin 1G phy (lan1, lan2, lan3)
       2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB:   1 x USB 3.2 Enhanced SuperSpeed port
UART:  3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)

Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
   reachable at 192.168.1.2/24. Rename the image to C0A80101.img.

2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
   console, Interrupt the autoboot process by pressing ESC when prompted.

3. Download and boot the OpenWrt initramfs image.

   $ env set uboot_bootcount 0
   $ env set firmware nominal
   $ tftpboot
   $ bootm

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
----------------

- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
  OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
  not configured by OpenWrt.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-08-20 01:14:06 +02:00
Bjørn Mork
1dd1ac2c35 mediatek: filogic: set wan label in preinit
Implement the functionality of
target/linux/ramips/patches-5.15/700-net-ethernet-mediatek-support-net-labels.patch
in userspace, since the driver patch has been rejected as a generic solution:
https://github.com/openwrt/openwrt/pull/11435

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-08-20 01:14:06 +02:00
Thomas Kupper
4d79a65d60 ipq807x: add support for Netgear RAX120v2
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.

The majority of the code is based on @jewwest's PR #11830.

Specifications:
    * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
    * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
    * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
    * Ethernet: 4x 10/100/1000 Mbps LAN,
                1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
                1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
    * Wi-Fi:
        * 2.4 GHz: Qualcomm QCN5024 4x4
        * 2x 5 GHz: Qualcomm QCN5054 4x4
    * USB: 2x USB 3.0
    * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
    * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
    * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
    * Power: 19 VDC, 3.1 A

Installation:
    * Flashing OpenWrt is done in two steps:
        a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
           This writes an initramfs based OpenWrt image onto the RAX120v2
        b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline

    * U-Boot allows booting an initramfs image via TFTP:
    - Set ip of your PC to 192.168.1.100
        - At the serial console interrupt boot at "Hit any key to stop autoboot:"
        - In u-boot run `tftpsrv`
        - On your PC send the OpenWrt initramfs image:

          tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb

Make 5G Aquantia phy work:
    For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
    u-boot by writing the firmware to the correct mtd partition.

    The firmware file found in the Netgear stock firmware under /lib/firmware/ named
    'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
    be converted to a MBN file.

    The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
    under 'git_home/u-boot.git/tools/mkheader.py'

    Convert the CLD file to MBN using:
    $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn

    This MBN file can then be flashed to the MTD partition to be used by u-boot.

    The necessary files can also be found in
        https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware

    * Write MBN file to MTD partition to be loaded automatically by u-boot:

      U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
      corresponds to `/dev/mtd25` in OpenWrt.

        - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)

          $ fgrep -i 'ethphyfw' /proc/mtd
          mtd25: 00080000 00020000 "ethphyfw

        - copy mbn file to /tmp/ folder of the router

          $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/

        - write mbn file to ethphyfw partition

          $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25

Revert to stock firmware:
    * Flash the stock firmware to the bootloader using TFTP/NMRP.

References to RAX120v2 GPL source:
    https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2023-08-19 17:12:46 +02:00
Robert Marko
8ae8612210 ipq40xx: qca8k: add ageing setting support
qca8k driver we are currently based of is rather out of date and is lacking
support for setting the ageing time or fast ageing so until we update the
driver lets just backport support for those from qca8k.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-19 16:48:33 +02:00
Andreas Böhler
edfe91372a ipq4019: add support for ZTE MF287 Pro aka DreiNeo Pro
The ZTE MF287 Pro is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF287+, but the hardware layout
and partition layout have changed quite a bit.

Specifications
==============

SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12
WiFi: 802.11a/b/g/n/ac SoC-integrated
USB: 1x 2.0

MAC addresses
=============

LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x82000000 openwrt.bin
  bootm 0x82000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m17
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd17 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock17 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 17
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.

Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.

Other Notes
===========

Contrary to the stock firmware, the USB port on the back can be used.

There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-08-19 16:31:39 +02:00
Christian Marangi
6b63fcf8df
generic: 6.1: backport patch adding support for LED PHY
Backport patch adding support for LED PHY directly in PHY ops struct.
Add new PHYLIB_LEDS config and refresh patches.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-08-19 12:51:08 +02:00
Arınç ÜNAL
2214bab350 bcm53xx: add support for ASUS RT-AC3100
ASUS RT-AC3100 is ASUS RT-AC88U without the external switch.

OpenWrt forum users effortless and ktmakwana have confirmed that there are
revisions with either 4366b1 or 4366c0 wireless chips.

Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-08-19 11:03:11 +02:00
Arınç ÜNAL
b7ee8c9f83 bcm53xx: backport DT changes for ASUS RT-AC3100 queued for v6.6
Backport the patch that adds the DT for ASUS RT-AC3100.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-08-19 11:03:11 +02:00
John Audia
973c5d4a1d kernel: bump 5.15 to 5.15.127
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.127

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-18 23:14:08 +02:00
John Audia
93fabc05dc kernel: bump 6.1 to 6.1.46
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.46

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-18 23:12:29 +02:00
Rafał Miłecki
5356462ce5 Revert "kernel: switch back 5.15 to fw_devlink=permissive"
This reverts commit 79af0593a3.

A hack adjusting fw_devlink value was added to workaround issue with
probing device drivers caused by of_platform_populate(). With upstream
mtd commit (the one adding OF_POPULATED) backported there is no need for
that hack anymore.

Ref: 3eebb91317 ("kernel: backport proper fix for mtd preventing devices probing")
Ref: #10232
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-08-18 10:51:01 +02:00
Robert Marko
46ed38adeb ipq40xx: remove DK01 and DK04 boards
DK01 and DK04 board support has been in a form of 2 patches that we have
been carrying for a long time.
Both of the patches contain weird changes, dont follow any DT syntax and I
honestly doubt they are even valid.
DK01 and DK04 also have not been converted to DSA even after a long time
and I doubt that anybody in the community even has these boards as they are
QCA reference boards that are not even obtainable anymore.

Since patches for these 2 boards have been just causing us pain when trying
to update the kernel to a new major release or even point releases lets
remove the support for these boards, and if there are users they can easily
be reinstated.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-15 16:41:22 +02:00
Robert Marko
0e6982b253 ipq40xx: Use SoC DTSI for Teltonika RUTX
Teltonika RUTX currently is the only device pulling in DK01 DTSI and thus
preventing removal of DK01 and DK04 support.

So, lets add the missing nodes from DK01 DTSI and use the SoC DTSI instead.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-15 16:41:22 +02:00
Robert Marko
7661e164c0 ipq40xx: add header to SCM cold boot address patch
Lets add a proper commit title and description to the SCM cold boot
patch so it applies with a git apply or git-am.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-15 16:38:50 +02:00
Robert Marko
a4aac5909e ipq40xx: update SCM SDI patches with pending upstream
SCM SDI disable support is pending upstream, so lets use that instead.

Since the board check needs to be split out, export it with a header so
it applies with git-am.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-15 16:38:49 +02:00
Martin Schiller
0af88d2512 linux/named-gpio-export: add support for OPEN_DRAIN and OPEN_SOURCE flag
This change makes it possible to use the GPIO_OPEN_DRAIN /
GPIO_OPEN_SOURCE Flags when exporting GPIOs via dts.

We need to emulate the open-source or open-drain functionalities for the
initial value, because the used functions (gpiod_direction_output_raw)
do not take this into account.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2023-08-15 16:07:04 +02:00
Mathew McBride
7770d08e2b armsr: armv8: fix invalid symbol value for FSL_ENETC_QOS
The kernel FSL_ENETC_QOS option is only a compile time
option, it does not result in a separate module being built.

Set it to 'y' to resolve a warning from the kernel compile:

.config:2654:warning: symbol value 'm' invalid for FSL_ENETC_QOS

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c3151b6f04 ("armvirt: 64: add support for other SystemReady-compatible vendors")
2023-08-15 15:55:00 +02:00
Mathew McBride
9cb173e9f1 armsr: armv8: enable AHCI/SATA controllers for mvebu,qoriq,juno
When comparing the generated OpenWrt .config to the Linux arm64
defconfig, I noticed these SATA controllers were not included.
As they may be used as a boot drive, they should be built into
the kernel.

CONFIG_SATA_MVEBU is for Marvell platforms.
CONFIG_SATA_QORIQ is for NXP Layerscape.
CONFIG_SATA_SIL24 is for Arm's Juno development board, see Linux
kernel commit d7c38ff1cd86 ("arm64: defconfig: Add Juno SATA
controller").

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
0018b33531 armsr: armv8: package and select MDIO driver for Thunder SoC's
This MDIO driver was already being built, but not installed due
to being selected by the ThunderX Ethernet driver.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
7c5bdff9c4 armsr: add Marvell (Cavium) ThunderX2 network driver
The initial armv8 module incorrectly labelled the Thunder(v1) as
supporting the ThunderX2, when they have different drivers.

Add kmod-octeon-tx2 to support the newer devices.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
15d3536c9d armsr: armv8: synchronize PCIE related options with arm64 defconfig
This turns on various PCI related options which are enabled
in the Linux kernel arch/arm64/configs/defconfig but not
yet in the OpenWrt config.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
911ee97774 armsr: armv8: add bcmgenet (Raspberry Pi 4 GENET) to profile
kmod-bcmgenet is needed for Ethernet support on the
Raspberry Pi 4.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
27ca83c627 armsr: armv8: add Broadcom GENET and MDIO modules
These are used by common Broadcom SoC's like
the BCM2711 (RPi4) and iProc network processor.

Tested on the RPi4B using the Raspberry Pi
UEFI+ACPI firmware[1].

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] - https://github.com/pftf/RPi4
2023-08-15 15:55:00 +02:00
Mathew McBride
df23eed179 armsr: armv8: enable Broadcom arch'es
This is part of an effort to reduce differences between
the OpenWrt armsr/armv8 config and Linux arm64 defconfig.

This enables CONFIG_ARCH_BCM and downstream
CONFIG_ARCH_BCM2835 (= BCM2711 like Raspberry Pi 4)
and CONFIG_ARCH_BCM_IPROC (Broadcom iProc packet processors).

The broadband specific SoC's (ARCH_BCMBCA) are left out
as it is assumed these will not be doing EFI boot.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
1ff4f4df23 armsr: armv8: enable CONFIG_ARCH_RENESAS
Renesas markets several embedded Arm64 SoCs in the
RZ series (RZ/G, RZ/V), so should be enabled in
a general purpose target.

Automotive (R-Car) SoC's are not enabled by this change.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
45b445498b armsr: armv8: fix NXP/Freescale i.MX family configuration
Due to an error on my part, Anton Antonov's
i.MX changes[1] did not fully make it into my
armvirt kernel 6.1 EFI pull request. I have updated
them using the options he supplied[1] as well
as comparing to the Linux arm64 defconfig.

The notable exception is:
CONFIG_USB_DWC3_OF_SIMPLE currently disabled
due to an issue with i.MX8P and i.MX8Q.

Fixes: 3efb3b8 ("armvirt: 64: Add NXP i.MX 8M Mini/Nano/Quad/Plus EVK support")

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] - ccf826c344
2023-08-15 15:55:00 +02:00
Mathew McBride
c4c60e4b19 armsr: enable ACPI_BUTTON
A review of the generated OpenWrt kernel .config
vs the Linux arm64 defconfig showed that this
option was not being enabled, as it is disabled
in OpenWrt's generic config.

ACPI_BUTTON is needed to report and respond to
power button events, so it should be enabled.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
22e0c7be47 armsr: armv8: sync CPU features, EFI, CMA and scheduler options with Linux defconfig
To bring the armsr/armv8 kernel configuration closer to the Linux
arm64 defconfig, synchronize options related to CPU features
(especially more recent Armv8.X variants), scheduler, EFI vars,
CMA and scheduler options.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
e505873e65 armsr: armv8: enable KVM host
x86/64 enables support for KVM so I can't see a reason why
not on armsr/armv8 as well.

Arm CPU errata workaround items related to virtualization
are also enabled by this change.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
5c4239ac3f armsr: armv8: sync Arm64 erratum options with kernel defconfig
To reduce differences with the Linux arm64 defconfig,
sync the enabled erratum items with defconfig.

There are still some options not selected due to
CONFIG_KVM or other options not enabled in OpenWrt
by default.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Hauke Mehrtens
54d470ed0e x86: Add virtualization time sync support
This compiles the CONFIG_PTP_1588_CLOCK support into the kernel binary
and activates the drivers for KVM and VMware which allow syncing the
host time with the VM when OpenWrt is running in a VM. With this change
the CONFIG_HYPERV_UTILS driver is now build into the kernel, because it
depends on the PTP framework being compiled in. CONFIG_HYPERV_UTILS was
build as a module, but not packages before.

Fixes: #13277
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-08-14 20:13:12 +02:00
Hauke Mehrtens
ff71035751 x86: Activate CONFIG_PCIEASPM
This activates PCI Express ASPM control in Linux. Without this option it
is completely controlled by the BIOS, now Linux will take over and apply
some workarounds if needed.

Fixes: #13248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-08-14 20:10:29 +02:00
Ivan Pavlov
54e5e396c5 ramips: improve Xiaomi mi-mini indications
Sets status indications led color on Xiaomi mi-mini router as other Xiaomi routers

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
2023-08-14 20:08:05 +02:00
Robert Marko
f1c80445bd ipq40xx: meraki: define DTB load address
It seems that the Meraki bootloader does not respect the kernel ARM booting
specification[1] that requires that address where DTB is located needs to
be 64-bit aligned and often places the DTB on a non 64-bit aligned address
and then kernel fails to find the DTB magic and fails to boot.
Even worse, there is no prints until early printk is enabled and then its
visible that kernel is trying to find the ATAG-s as DTB was not found or
is invalid.

Unifi 6 devices had the same issue and it can be solved by passing the
load adress as part of the FIT image.
It seems that the vendor was aware of the issue and is always relocating
the DTB to 0x89000000, so lets just do the same.

Now that booting is reliable, reenable default images for the Meraki MR33
and MR74 devices.

Reviewed-by: Lech Perczak lech.perczak@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-14 19:29:25 +02:00
Robert Marko
bb4a25860f ipq40xx: meraki: remove swconfig in DEVICE_PACKAGES
ipq40xx was converted to DSA and swconfig is not being included at all in
the default packages so there is no need to drop it from device packages.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-14 19:28:56 +02:00
Robert Marko
9e9dc1890c ipq40xx: commonize Meraki recipe
MR33 and MR74 share pretty much everything in the image recipe, so lets
extract a common recipe to avoid duplication.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-14 19:28:56 +02:00
Daniel Golle
e6f8b69918 generic: backport fix for Winbond SPI NAND
Avoid using stack allocated memory for DMA operations.

Fixes: 156c00dedc ("generic: backport Winbond W25N02KV SPI-NAND support")
Fixes: b71c870caa ("generic: 6.1: re-add two Winbond nand fixes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-13 15:01:37 +01:00
Daniel Golle
42e14d3ed8 generic: 5.15: rename patches to match correct version
Rename two patches which were only accepted in Linux 6.2, but were
marked as if they were accepted in Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-13 15:01:37 +01:00
Daniel Golle
c524a76f4c armsr: remove redundant phy-marvell-10g module
the Marvell 10G PHY driver is no way specific to ARM SystemReady
systems, it frequently occurs on SFP+ copper modules and is useful on
many targets.

Hence it been added to package/kernel/linux/modules/netdevices and we
can remove the now redundant target-specific module.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-13 15:01:36 +01:00
Daniel Golle
0454691960 mediatek: filogic: mt7988: mark RTC clock as critical
A dependency of the MT7988 MMC host controller on the SoC's RTC clock
being running has been discovered. Mark RTC clock as critical to fix
MMC host on MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-13 15:01:36 +01:00
John Audia
64782497db kernel: bump 5.15 to 5.15.126
1. Disable unneeded errata Kconfig symbols
2. Update kernel

Changelog: https://lore.kernel.org/stable/2023081111-unlocking-synopsis-d7d5@gregkh/

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-13 13:03:43 +02:00
Zoltan HERPAI
22d7ac4b80 sunxi: bananapro: add firmware files for Ampak 6181
The Bananapro board has an Ampak 6181 onboard (BCM43362/1), enable
the firmware files in the device profile, and add wpad-basic-mbedtls.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-08-12 14:00:18 +02:00
John Audia
093d317d20 kernel: bump 6.1 to 6.1.45
Changelog: https://lore.kernel.org/stable/2023081123-ion-ferment-1ce5@gregkh/

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #x86_64 (j1900)
Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-12 12:10:36 +02:00
Zoltan HERPAI
80edfaf675 sunxi: add support for Banana Pi M3
CPU	Allwinner A83t Octa-core Cortex A7 @ 1.2GHz
Memory  2Gb DDR3
Storage	SDcard, SATA (via USB), 8GB eMMC
Network	10/100/1000M ethernet, Ampak AP6212 wifi + BT
USB	2x USB 2.0

Flashing instructions:
 Standard sunxi SD card installation procedure - copy image to SD card,
 insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-08-11 18:04:44 +02:00
Zoltan HERPAI
dc122f4d9e sunxi: add modules for AC100 MFD and RTC
The X-Powers AC100 is a multi-function IC used to provide RTC
and audio codec via RSB (reduced serial bus, an Allwinner-
speciality). On some boards using the A80/A83T SoCs, aside
from the RTC functionality, the RTC is used as a clocksource
for the Ampak WiFi/BT modules.

Add modules for the core MFD support and the RTC.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-08-11 18:04:43 +02:00
Tomasz Maciej Nowak
5e6bab661a mvebu: mcbin-singleshot: enable hearbeat LED by default
This has been a part of modified upstream patch but got lost on major
kernel bump to 5.15, so bring it back.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Add patch for kernel 6.1 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-08-10 23:09:37 +02:00
Linus Walleij
c764a8c791 gemini: Fix up kernel v6.1 config
The v6.1 kernel has moved around the options for the RTL8366RB
DSA switch used in the DIR-685 so it was missing when building
the kernel. Fix it up by adding the right Kconfig options.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-08-10 19:31:37 +02:00
Robert Marko
95f5dadda6 qualcommax: remove upstreamed TRIM quirks
TRIM disable quirks for eMMC-s were merged upstreamed and backported to
stable in 6.1.39, however they were not dropped during the kernel update
and quilt is not complaining at all.

So, lets manually remove them as they are part of 6.1.39 [1] [2].

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/mmc/core/quirks.h?h=v6.1.39&id=182bf07a24c4c1022bf83c90be619d60427745c3
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/mmc/core/quirks.h?h=v6.1.39&id=69bc3203513c4fcd6ca84b0185de454bacf87883

Fixes: fec22f8375 ("kernel: bump 6.1 to 6.1.39")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-10 16:20:40 +02:00
Robert Marko
0edce7d5d9 qualcommax: refresh kernel config
Refresh the kernel config to keep in sync with the generic one.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-10 16:18:27 +02:00
John Audia
1e0ee72b72 kernel: bump 6.1 to 6.1.44
Changelog: https://lore.kernel.org/stable/2023080822-repost-unfiled-2f01@gregkh/

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 20:39:20 -04:00
John Audia
549e710fc0 kernel: bump 6.1 to 6.1.43
1. Disable Ampere errata fix in target/linux/generic/config-6.1

2. Update kernel Changelog: https://lore.kernel.org/stable/2023061431-modular-data-8489@gregkh/

Manually rebased:
        bcm27xx/patches-6.1/950-0359-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
        bcm27xx/patches-6.1/950-0362-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
        bcm27xx/patches-6.1/950-0390-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
        bcm27xx/patches-6.1/950-0469-usb-xhci-add-XHCI_VLI_HUB_TT_QUIRK.patch
        bcm27xx/patches-6.1/950-0520-xhci-constrain-XHCI_VLI_HUB_TT_QUIRK-to-old-firmware.patch

All other patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 20:39:20 -04:00
John Audia
daed3322d3 kernel: bump 5.15 to 5.15.125
1. Add new symbols to generic config
2. Bump kernel
   Changelog: https://lore.kernel.org/stable/2023080818-groin-gradient-a031@gregkh/

   All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 22:06:24 +02:00
John Audia
81c1172c36 kernel: bump 5.15 to 5.15.124
Changelog: https://lore.kernel.org/stable/2023080341-curliness-salary-4158@gregkh/

1. Needed to make a change to to package/kernel/linux/modules/netsupport.mk
   due to upstream moving vxlan to its own directory[1].  @john-tho suggested
   using the the 6.1 xvlan FILES to circumvent.
2. All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.124&id=77396fa9096abdbfbb87d63e73ad44d5621cf103

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-09 22:06:23 +02:00
David Bauer
7e7eb5312d mediatek: add support for Acer Predator W6
Hardware
--------
SOC:   MediaTek MT7986A
RAM:   1GB DDR4
FLASH: 4GB eMMC
WiFi:  2x2 2.4 GHz 802.11 b/g/n/ax MT7916 DBDC
       4x4 5 GHz   802.11 a/n/ac/ax MT7986
       2x2 6 GHz   802.11ax MT7916 DBDC
ETH:   4x LAN 1Gbit/s (MT7531)
       1x WAN 2.5Gbit/s (GPY211)
BTN:   RESET, WPS
LED:   Antenna LEDs (GPIO)
       Mood-LED (Kinetic KTD2601) - unsupported
UART:  Header nest to USB port - 3V3 115200 8N1
       [BUTTON] GND - RX - TX [USB]

Installation
------------

1. Connect to the device using serial console.

2. Interrupt the Autoboot process when promted by sending '0' twice.

3. Serve the OpenWrt initramfs image using TFTP at 192.168.1.66. Name
   the image "predator.bin" and conenct the TFTP server to the routers
   LAN port.

4. Configure U-Boot to allow loading unsigned images from MMC

   $ setenv bootcmd 'mmc read 0x40000000 0x00004400 0x0010000;
     fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 0x40000000';
     saveenv

5. Transfer the image from U-Boot

   $ setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1;
     tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr);
     fdt rm /signature; bootm

6. Wait for OpenWrt to boot

7. Transfer the OpenWrt sysupgrade image to the router using scp.

8. Install OpenWrt using sysupgrade.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-05 18:42:45 +02:00
Daniel Golle
1eb67cb070 mediatek: filogic: restore non-const type in pinctrl-mt7988 driver
When building with Linux 5.15 the 'const' type results in warnings.
Restore the original non-const type in those cases.

Fixes: 36d0aa9c2d ("mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDK")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-03 23:34:22 +01:00
Daniel Golle
64b99802a6 mediatek: filogic: update MT7988 device tree
* move ethernet to mt7988a.dtsi
 * move switch definition to mt7988a.dtsi
 * add PHY LEDs

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-03 15:47:51 +01:00
Daniel Golle
36d0aa9c2d mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDK
Update pinctrl driver for the MT7988 with driver from mtk-openwrt-feeds.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-03 15:47:51 +01:00
Stefan Kalscheuer
801c67b4e0 mvebu: add kernel 6.1 as testing kernel
With an initial set of patches and configs in place let's start testing
with kernel 6.1.

Run-tested on the cortexa9 subtarget (WRT1900ACS, Turris Omnia)

Tested-by: Etienne Champetier <champetier.etienne@gmail.com>
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
2023-08-02 16:21:19 +02:00
Stefan Kalscheuer
b1993f362a mvebu: copy 5.15 kconfigs to 6.1
Start 6.1 migration with a full copy of the current stable config.

Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
2023-08-02 16:21:19 +02:00
Stefan Kalscheuer
7f257296ec mvebu: refresh patches for 6.1
Remove the following patches:
100-ARM-dts-turris-omnia-configure-LED-0-pin-function-to [1]
101-ARM-dts-turris-omnia-enable-LED-controller-node [2]
702-net-next-ethernet-marvell-mvnetaMQPrioOffload [3]
703-net-next-ethernet-marvell-mvnetaMQPrioFlag [4]
704-net-next-ethernet-marvell-mvnetaMQPrioQueue [5]
705-net-next-ethernet-marvell-mvnetaMQPrioTCOffload [6]
710-v6.2-phy-marvell-phy-mvebu-a3700-comphy-Reset-COMPHY-regi [7]

Manually rebased:
902-drivers-mfd-Add-a-driver-for-IEI-WT61P803-PUZZLE-MCU

All other patches automatically rebased

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=94a29bffdd59498382131fd428fed221f5c96def
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=40624346b7ae0c2b1209fc9993ea30699e512c50
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=75fa71e3acadbb4ab5eda18505277eb9a1f69b23
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=e7ca75fe6662f78bfeb0112671c812e4c7b8e214
[5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=e9f7099d0730341b24c057acbf545dd019581db6
[6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=2551dc9e398c37a15e52122d385c29a8b06be45f
[7] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=cd1e1735aeab49abc679218a79ee764c0d394880

Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
2023-08-02 16:21:19 +02:00
Stefan Kalscheuer
04f6d674f6 mvebu: copy 5.15 patches to 6.1
To start migration to Kernel 6.1 we copy all existing patches from 5.15.

Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
2023-08-02 16:21:19 +02:00
Daniel Golle
dc4aafb309 mediatek: filogic: enable driver for MediaTek XS-PHY
Enable driver for MediaTek SuperSpeedPlus XS-PHY transceiver for the
USB3.1 GEN2 controllers found in the MT7988 SoC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-31 18:05:22 +01:00
Robert Marko
5757b21db0 qualcommax: ipq807x: fix Gen2 PCIe port
Gen2 PCIe port recently got broken on IPQ807x during update to 6.1.39 as
upstream backported:
("PCI: qcom: Remove PCIE20_ prefix from register definitions") [1]

So, fix it by adding a pending upstream fix for it [2].

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/pci/controller/dwc/pcie-qcom.c?h=v6.1.39&id=db962c7a711c3393a80a18219960cd54fb33c53d
[2] https://patchwork.kernel.org/project/linux-arm-msm/patch/20230724063429.3980462-1-quic_srichara@quicinc.com/

Fixes: fec22f8375 ("kernel: bump 6.1 to 6.1.39")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-07-31 12:08:34 +02:00
John Audia
c4a5fe6cee kernel: bump 6.1 to 6.1.42
Manually rebased:
	generic/pending-6.1/203-kallsyms_uncompressed.patch

All other patches automatically rebased.

Changelog: https://lore.kernel.org/stable/2023072749-gumming-selector-a081@gregkh/

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-07-30 18:53:00 +02:00
John Audia
8590531048 kernel: bump 5.15 to 5.15.123
Manually rebased:
	bcm4908/patches-5.15/071-v6.1-0001-net-broadcom-bcm4908_enet-handle-EPROBE_DEFER-when-g.patch
	bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
	ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch[*]

Removed upstreamed:
	backport-5.15/735-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1]
	backport-5.15/817-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[2]
	pending-5.15/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[3]
	pending-5.15/160-workqueue-fix-enum-type-for-gcc-13.patch[4]
	bcm53xx/patches-5.15/036-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[5]
	bcm53xx/patches-5.15/036-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[6]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=02474292a44205c1eb5a03634ead155a3c9134f4
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=86b93cbfe104e99fd3d25a49748b99fb88101573
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=79b9ab357b6f5675007f4c02ff8765cbd8dc06a2
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=d528faa9e828b9fc46dfb684a2a9fd8c2e860ed8
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=5899bc4058e89d5110a23797ff94439c53b77c25
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=95afd2c7c7d26087730dc938709e025a303e5499

Build system: x86/64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Audia <therealgraysky@proton.me>
[rebased ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch ]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-07-30 18:02:47 +02:00
Shiji Yang
96010bb17c ramips: mt7621-wdt: use phandle to access system controller registers
These patches allow the driver to access some watchdog registers via a
phandle to the system controller node[1]. To apply these changes, we
need to add "mediatek,sysctl" to the SoC dtsi. This commit also remove
the redundent clocks, interrupts and resets properties.

[1] https://lore.kernel.org/all/20230214103936.1061078-2-sergio.paracuellos@gmail.com

Tested on Motorola MWR03 (MT7628)

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-30 13:09:23 +02:00
Shiji Yang
1f818b09f8 ramips: add proper system clock and reset driver support for legacy SoCs
This series of upstream patches properly implement a clock and reset
driver for old ralink SoCs[1]. And it includes some related fixes[2] and
improvements[3][4]. All patches have been merged into linux-next. They
will be part of upcoming Linux 6.5. In order to switch to the new system
controller driver, all clocks and resets properties in SoC dtsi have been
updated, and kernel symbol "CONFIG_CLK_MTMIPS" have been added to the
kernel config files.

[1] https://lore.kernel.org/all/20230619040941.1340372-1-sergio.paracuellos@gmail.com
[2] https://lore.kernel.org/all/20230622-mips-ralink-clk-wuninitialized-v1-1-ea9041240d10@kernel.org
[3] https://lore.kernel.org/all/OSYP286MB03120BABB25900E113ED42B7BC5CA@OSYP286MB0312.JPNP286.PROD.OUTLOOK.COM
[4] https://lore.kernel.org/all/TYAP286MB03151148AF8C054621DD55C3BC23A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM

Tested on Motorola MWR03 (MT7628)
Tested on Haier HW-L1W (MT7620)

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-30 13:09:23 +02:00
Shiji Yang
8cacf2bda8 ramips: add proper system clock and reset driver support for mt7621
This series of upstream patches makes the system controller node as a
reset provider[1][2], and it also includes some clock and reset driver
fixes[3][4]. Meanwhile, all clocks and resets properties in the SoC
device tree have been updated to be compatible with the new driver.

[1] https://lore.kernel.org/r/20220110114930.1406665-2-sergio.paracuellos@gmail.com
[2] https://lore.kernel.org/r/20220210094859.927868-2-sergio.paracuellos@gmail.com
[3] https://lore.kernel.org/r/20221217074806.3225150-1-sergio.paracuellos@gmail.com
[4] https://lore.kernel.org/r/20230206083305.147582-1-sergio.paracuellos@gmail.com

Tested on RAISECOM MSG1500 X.00

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-30 13:09:23 +02:00
Rafał Miłecki
3eebb91317 kernel: backport proper fix for mtd preventing devices probing
Improper of_platform_populate() call caused issue with probing devices
drivers.

Fixes: 41e1e838fb ("kernel: backport mtd patch adding of_platform_populate() calls")
Fixes: #10232
Ref: 79af0593a3 ("kernel: switch back 5.15 to fw_devlink=permissive")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-30 01:05:49 +02:00
Rafał Miłecki
ca8868a511 bcm53xx: backport more DT changes queued for v6.6
Those sort out BCM53573 Ethernet info finally.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-29 17:04:53 +02:00
Shiji Yang
b4ea49ad44 ramips: pinctrl: support requesting different functions for same group
MT7620 wireless radio needs change the pin group function between
"gpio" and "pa" during the calibration process. However, ralink
pinctrl driver doesn't support requesting different functions for
the same group. This patch enables pinctrl consumers to perform
such operations.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-07-29 15:07:11 +01:00
Rafał Miłecki
03b3284805 ramips: use NVMEM cells with mt76 EEPROM for Netgear R6220 & WNDR3700 v5
This uses new upstream DT binding. It's more generic (NVMEM) compared to
the old one (MTD).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-28 19:42:46 +02:00
Rafał Miłecki
e6cf959d0e ramips: use fixed layout cell "mac-base" for Netgear WNDR3700 v5
This drops a use of downstream "mac-address-increment".

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-28 18:50:39 +02:00
Rafał Miłecki
daaa0c1b25 ath79: replace "mac-address-ascii" with "mac-base"
With upstream accepted "mac-base" binding there is no need for a
downstream "mac-address-ascii" workaround anymore.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-28 10:28:05 +02:00
Petr Štetiar
edd146c920
mediatek: filogic: fix broken sysupgrade script
Changes introduced in commit 54dc1cde48 ("mediatek: filogic: add
support for Xiaomi WR30U") missed to end the case item with mandatory
`;;` which lead to a broken sysupgrade.

Fixes: 54dc1cde48 ("mediatek: filogic: add support for Xiaomi WR30U")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-07-28 08:24:11 +02:00
Petr Štetiar
ba415af570
ipq807x: prpl-haze: fix sysupgrade flashing from bootloader
While flashing sysupgrade image from U-Boot, then the rootfs_data
overlay filesystem formatting is left for the fstools during firstboot,
but that wont work as mkfs.f2fs is missing in the sysupgrade image:

 mount_root: overlay filesystem in /dev/loop0 has not been formatted yet
 mount_root: no usable overlay filesystem found, using tmpfs overlay
 sh: mkfs.f2fs: not found

 Filesystem                Size      Used Available Use% Mounted on
 /dev/loop0              139.6M     46.9M     92.6M  34% /overlay

 Number  Start (sector)    End (sector)  Size       Code  Name
  20           98850          406349   150.1 MiB   FFFF  rootfs

So lets fix it by adding f2fs support to the sysupgrade image.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-07-28 08:19:18 +02:00
Hank Moretti
dcdcfc1511 mediatek: filogic: add specific layout for WR30U
Because this device enable NMBM by default, most users use custom
U-Boot with NMBM-Enabled in Chinese forums.

This layout is the same as the ubootmod layout but enabling NMBM.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-07-27 13:46:26 +02:00
Hank Moretti
54dc1cde48 mediatek: filogic: add support for Xiaomi WR30U
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: NT52B128M16JR-FL 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A

Flash instructions:

1. Get ssh access
   Check this link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000ne/153769/22

2. Backup import partitions
   ```
   dev:    size   erasesize  name
   mtd1: 00100000 00020000 "BL2"
   mtd2: 00040000 00020000 "Nvram"
   mtd3: 00040000 00020000 "Bdata"
   mtd4: 00200000 00020000 "Factory"
   mtd5: 00200000 00020000 "FIP"
   mtd8: 02200000 00020000 "ubi"
   mtd9: 02200000 00020000 "ubi1"
   mtd12: 00040000 00020000 "KF"

   ```

   Use these commands blow to backup your stock partitions.
   ```
   nanddump -f /tmp/BL2.bin /dev/mtd1
   nanddump -f /tmp/Nvram.bin /dev/mtd2
   nanddump -f /tmp/Bdata.bin /dev/mtd3
   nanddump -f /tmp/Factory.bin /dev/mtd4
   nanddump -f /tmp/FIP.bin /dev/mtd5
   nanddump -f /tmp/ubi.bin /dev/mtd8
   nanddump -f /tmp/KF.bin /dev/mtd12
   ```
   Then, transfer them to your computer via scp, netcat, tftp
   or others and keep them in a safe place.

3. Setup Nvram
   Get the current stock: `cat /proc/cmdline`

   If you find `firmware=0` or `mtd=ubi`, use these commands:
   ```
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=1
   nvram set flag_last_success=1
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   ```

   If you find `firmware=1` or `mtd=ubi1`, use these commands:
   ```
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=0
   nvram set flag_last_success=0
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   ```

4. Flash stock-initramfs-factory.ubi
   If you find `firmware=0` or `mtd=ubi`:
   `ubiformat /dev/mtd9 -y -f /tmp/stock-initramfs-factory.ubi`

   If you find `firmware=1` or `mtd=ubi1`:
   `ubiformat /dev/mtd8 -y -f /tmp/stock-initramfs-factory.ubi`

   Then reboot your router, it should boot to the openwrt
   initramfs system now.

5. Setup uboot-env
   Now it will be setup automatically in upgrade process,
   you can skip this step.

   If your `fw_setenv` did not work, you need run this command:
   `echo "/dev/mtd1 0x0 0x10000 0x20000" > /etc/fw_env.config`

   Then setup uboot-env:
   ```
   fw_setenv boot_wait on
   fw_setenv uart_en 1
   fw_setenv flag_boot_rootfs 0
   fw_setenv flag_last_success 1
   fw_setenv flag_boot_success 1
   fw_setenv flag_try_sys1_failed 8
   fw_setenv flag_try_sys2_failed 8
   fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),
   2048k(factory),2048k(fip),256k(crash),256k(crash_log),
   34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)"
   ```

6. Flash stock-squashfs-sysupgrade.bin
   Use shell command:
   `sysupgrade -n /tmp/stock-squashfs-sysupgrade.bin`
   Or go to luci web.

If you need to change to Openwrt U-Boot layout, do next. If you
do not need, please ignore it.

Change to OpenWrt U-Boot:

1. Flash ubootmod-initramfs-factory.ubi
   Check mtd partitions: `cat /proc/mtd`
   ```
   mtd7: 00040000 00020000 "KF"
   mtd8: 02200000 00020000 "ubi_kernel"
   mtd9: 04e00000 00020000 "ubi"
   ```

   Run following command:
   `ubiformat /dev/mtd8 -y -f /tmp/ubootmod-initramfs-factory.ubi`
   Then reboot your router, it should boot to the openwrt initramfs
   system now.

2. Check mtd again
   ```
   mtd7: 00040000 00020000 "KF"
   mtd8: 07000000 00020000 "ubi"
   ```
   Make sure mtd8 is ubi.

3. Install kmod-mtd-rw
   Run command: `opkg update && opkg install kmod-mtd-rw`
   Or get it in openwrt server, or build it yourself, then install
   it manually

   Then run this command:
   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Clean up pstore
   Run Command: `rm -f /sys/fs/pstore/*`

5. Format ubi and create new ubootenv volume
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
   ```

6. (Optional) Add recovery boot feature.
   ```
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
   ubiupdatevol /dev/ubi0_2 /tmp/ubootmod-initramfs-recovery.itb
   ```

7. Flash Openwrt U-Boot
   ```
   mtd write /tmp/ubootmod-preloader.bin BL2
   mtd write /tmp/ubootmod-bl31-uboot.fip FIP
   ```

6. Flash ubootmod-squashfs-sysupgrade.itb
   Use shell command:
   `sysupgrade -n /tmp/ubootmod-squashfs-sysupgrade.itb`
   Or go to luci web.

Now everything is done, Enjoy!

Go Back to stock from Openwrt U-Boot:

1. Force flash ubootmod-initramfs-recovery.itb
   Use shell command:
   `sysupgrade -F -n /tmp/ubootmod-initramfs-recovery.itb`
   Or go to luci web.
   Then it should boot to the openwrt initramfs system now.

2. Format ubi and Nvram
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   mtd erase Nvram
   ```

3. Install kmod-mtd-rw
   Run command: `opkg update && opkg install kmod-mtd-rw`
   Or get it in openwrt server, or build it yourself, then install
   it manually

   Then run this command:
   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Flash stock U-Boot and ubi
   ```
   mtd write /tmp/BL2.bin BL2
   mtd write /tmp/FIP.bin FIP
   mtd write /tmp/ubi.bin ubi
   ```
   Then reboot your router, waiting it finished rollback in minutes.

Go Back to stock from stock layout Openwrt:
   Just run command: `ubiformat /dev/mtd8 -y -f /tmp/ubi.bin`
   Then reboot your router, waiting it finished rollback in minutes.

Notes:
1. Openwrt U-Boot and ubootmod openwrt did not enable NMBM.
   Please make your backup safe.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-07-27 13:46:16 +02:00
Alexander Friese
6b11f0ec83 ipq4019: fix support for AVM FRITZ!Repeater 3000
new versions of the device have NAND with 8bit ECC
which was not yet supported before. This change removes
ECC restrictions.

Signed-off-by: Alexander Friese <af944580@googlemail.com>
2023-07-26 12:26:45 +02:00
Lu jicong
06d5c773fa rockchip: enable wifi support for NanoPC T4
wifi module: AP6356S (BCM4356) SDIO

Signed-off-by: Lu jicong <jiconglu58@gmail.com>
2023-07-26 12:15:20 +02:00
Lu jicong
ac9a2d6a35 rockchip: add FriendlyARM NanoPC T4 support
Hardware
--------
RockChip RK3399 ARM64 (6 cores)
4GB LPDDR3 RAM
1x 1000 Base-T
1 GPIO LED (status)
HDMI 2.0
3.5mm TRRS AV jack
Micro-SD slot
16GB eMMC
1x USB 3.0 Port
2x USB 2.0 Port
1x USB Type-C Port
1x M.2 PCI-E Port
AP6356S (BCM4356) SDIO WiFi & Bluetooth adapter
--------
Note: AP6356S is not supported yet due to the lack of firmware and NVRAM

Signed-off-by: Lu jicong <jiconglu58@gmail.com>
2023-07-26 12:15:20 +02:00
David Bauer
844bb4bfad ipq40xx: add support for Teltonika RUTX50
Hardware
--------
CPU:     Qualcomm IPQ4018
RAM:     256M
Flash:   16MB SPI-NOR (W25Q128)
         128MB SPI-NAND (XTX)
WiFi:    2T2R (2GHz 802.11n ; 5 GHz 802.11ac)
ETH:     4x LAN ; 1x WAN (Gigabit)
CELL:    Quectel RG501Q 3G/4G/5G

UART: Available on the goldfinger connector (Pinout silkscreened)
      115200 8N1 3V3 - Only connect RX / TX / GND

Installation
------------

1. Enable SSH in the Teltonika UI
   (System --> Administration --> Access Control)

2. Check from which partition set the device is currently running from.

   $ cat /proc/boot_info/rootfs/primaryboot

   In case this output reads 0, install a Software update from Teltonika
   first. After upgrade completion, check this file now reads 1 before
   continuing.

2. Transfer the OpenWrt factory image to the device using scp. Use the
   same password (user root!) as used for the Web-UI.

   $ scp -O openwrt-factory.bin root@192.168.1.1:/tmp

3. Connect to the device using ssh as the root user.

4. Install OpenWrt by writing the factory image to flash.

   $ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin

5. Instruct the bootloaer to boot from the first partition set.

   $ echo 0 > /proc/boot_info/rootfs/primaryboot
   $ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin
   $ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin
   $ mtd write /tmp/bootconfig.bin /dev/mtd2
   $ mtd write /tmp/bootconfig1.bin /dev/mtd3

6. Reboot the device.

   $ reboot

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-07-26 01:17:08 +02:00
David Bauer
dbc4be142e ipq40xx: move Teltonika RUT STM32 IO to specific DTS
Prepare to re-use the DTS for the RUTX50.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-07-26 01:17:08 +02:00
John Audia
d91f38a99e kernel: bump 6.1 to 6.1.40
Removed upstreamed:
	generic/backport-6.1/701-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1]
	generic/pending-6.1/160-workqueue-fix-enum-type-for-gcc-13.patch[2]
	qualcommax/patches-6.1/0022-v6.5-soc-qcom-mdt_loader-Fix-unconditional-call-to-scm_pa.patch[3]

Manually rebased:
	bcm27xx/patches-6.1/950-0359-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
	bcm27xx/patches-6.1/950-0362-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
	bcm27xx/patches-6.1/950-0390-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
	bcm27xx/patches-6.1/950-0469-usb-xhci-add-XHCI_VLI_HUB_TT_QUIRK.patch
	bcm53xx/patches-6.1/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=685b57a1221c38ec8b456f968264d2496715820c
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=2d57a1590f4d8c516f5aaf8fd5bb4f52d67275d8
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.40&id=33f8dff6e1cbba5c2ec85fa5649c0a759a7e685c

Build system: x86/64, filogic/xiaomi_redmi-router-ax6000-ubootmod
Build-tested: x86/64, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-07-25 00:24:21 +02:00
John Audia
fec22f8375 kernel: bump 6.1 to 6.1.39
Removed upstreamed:
	generic/backport-6.1/803-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[1]
	generic/pending-6.1/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[2]
	bcm27xx/patches-6.1/950-0034-drm-bridge-Introduce-pre_enable_upstream_first-to-al.patch[3]
	bcm27xx/patches-6.1/950-0439-nvmem-Use-NVMEM_DEVID_AUTO.patch[4]
	bcm4908/patches-6.1/040-mtd-parsers-refer-to-ARCH_BCMBCA-instead-of-ARCH_BCM.patch[5]
	bcm53xx/patches-6.1/031-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[6]
	bcm53xx/patches-6.1/031-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[7]
	mediatek/patches-6.1/351-cpufreq-mediatek-correct-voltages-for-MT7622-and-MT7.patch[8]
	qualcommax/patches-6.1/0008-v6.2-clk-qcom-reset-support-resetting-multiple-bits.patch[9]

Manually rebased:
	bcm27xx/patches-6.1/950-0035-drm-panel-Add-prepare_upstream_first-flag-to-drm_pan.patch
	bcm27xx/patches-6.1/950-0404-drm-panel-panel-ilitek9881c-Add-prepare_upstream_fir.patch
	bcm27xx/patches-6.1/950-0699-Bluetooth-hci_sync-Add-fallback-bd-address-prop.patch
	mediatek/patches-6.1/350-21-cpufreq-mediatek-Add-support-for-MT7988.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=ab0bd172d6289310a05a0cd15e1432e828d386ae
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=6df680709d901346831ef8f221cc90a42062c526
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=5044e5f2511c9afdf9880d2bb6b9d37dfc345dac
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=e27948f329f7e02591ed1feb9a7710c2ccf89a83
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=ad2928e7f3f6120a0bd18aa1056b3b24068027c5
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=2b55a985727833f37c39911f34096b3fdf2a367d
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=90d4c487cd658b51212eb65ae804ab11af193672
8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=7e3ee25e8c7c7be1eacdfc6d9f5f0e550a2af241
9. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.39&id=b20854ef6c4955be3310975a72f02d92cb01d6d4

Build system: x86/64
Build-tested: x86/64
Run-tested: x86/64

Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de>
Co-authored-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
[ rebase bcm27xx and mediatek patches, refresh commit description ]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[ minor fixup to bcm27xx patches, refresh commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-07-25 00:24:21 +02:00
Felix Fietkau
a110de8152 kernel: drop mips highmem offset start overrides
The maximum offset that can be supported is 0x20000000
Do not override it to to something bigger than that on MT7621, as that could
cause issues based on the fixed memory mappings. This makes the last 64 MB
RAM unusable on MT7621 devices with 512 MB but avoids incurring a heavy
performance hit

Fixes: cd2b74e01e ("ramips: mt7621: disable highmem support and remove highmem offset patch")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-24 14:45:29 +02:00
Felix Fietkau
cd2b74e01e ramips: mt7621: disable highmem support and remove highmem offset patch
On MT7621 it was observed, that enabling highmem support causes a significant
performance drop, as documented in: https://github.com/openwrt/openwrt/issues/13151
By adjusting the highmem start offset, we avoid leaving any RAM unaddressable,
even on devices with 512 MB

Fixes: https://github.com/openwrt/openwrt/issues/13151
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-24 13:36:39 +02:00
Rafał Miłecki
79fd3e62b4 bcm53xx: add BCM53573 Ethernet fix sent upstream for v6.6
It seems that DSA-based b53 driver never worked with BCM53573 SoCs and
BCM53125.

In case of swconfig-based b53 this fixes a regression. Switching bgmac
from using mdiobus_register() to of_mdiobus_register() resulted in MDIO
device (BCM53125) having of_node set (see of_mdiobus_register_phy()).
That made downstream b53 driver read invalid data from DT and broke
Ethernet support.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-07-23 22:49:13 +02:00
Christian Marangi
8912e386e3
bcm27xx: update dwc_otc driver with new kthread_complete_and_exit name
Kernel 6.1 renamed and moved complete_and_exit to
kthread_complete_and_exit.

This was just a rename and nothing is changed implementation wise.
Update to the new symbol name to fix compilation error.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-07-23 14:45:18 +02:00
David Bauer
36f7ececc2 mediatek: add missing SPDX header
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-07-22 17:41:22 +02:00
Daniel Golle
b1d10e0174 mediatek: filogic: set DEVICE_DTS_LOADADDR for BPi-R3
U-Boot complains that the overlayed DT needs relocation, so set
DEVICE_DTS_LOADADDR to have it relocated.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-07-22 12:31:31 +01:00