mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 13:48:06 +00:00
mediatek: filogic: add support for Xiaomi WR30U
Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: ESMT F50L1G41LB 128MB RAM: NT52B128M16JR-FL 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Mesh Power: DC 12V 1A Flash instructions: 1. Get ssh access Check this link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000ne/153769/22 2. Backup import partitions ``` dev: size erasesize name mtd1: 00100000 00020000 "BL2" mtd2: 00040000 00020000 "Nvram" mtd3: 00040000 00020000 "Bdata" mtd4: 00200000 00020000 "Factory" mtd5: 00200000 00020000 "FIP" mtd8: 02200000 00020000 "ubi" mtd9: 02200000 00020000 "ubi1" mtd12: 00040000 00020000 "KF" ``` Use these commands blow to backup your stock partitions. ``` nanddump -f /tmp/BL2.bin /dev/mtd1 nanddump -f /tmp/Nvram.bin /dev/mtd2 nanddump -f /tmp/Bdata.bin /dev/mtd3 nanddump -f /tmp/Factory.bin /dev/mtd4 nanddump -f /tmp/FIP.bin /dev/mtd5 nanddump -f /tmp/ubi.bin /dev/mtd8 nanddump -f /tmp/KF.bin /dev/mtd12 ``` Then, transfer them to your computer via scp, netcat, tftp or others and keep them in a safe place. 3. Setup Nvram Get the current stock: `cat /proc/cmdline` If you find `firmware=0` or `mtd=ubi`, use these commands: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ``` If you find `firmware=1` or `mtd=ubi1`, use these commands: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ``` 4. Flash stock-initramfs-factory.ubi If you find `firmware=0` or `mtd=ubi`: `ubiformat /dev/mtd9 -y -f /tmp/stock-initramfs-factory.ubi` If you find `firmware=1` or `mtd=ubi1`: `ubiformat /dev/mtd8 -y -f /tmp/stock-initramfs-factory.ubi` Then reboot your router, it should boot to the openwrt initramfs system now. 5. Setup uboot-env Now it will be setup automatically in upgrade process, you can skip this step. If your `fw_setenv` did not work, you need run this command: `echo "/dev/mtd1 0x0 0x10000 0x20000" > /etc/fw_env.config` Then setup uboot-env: ``` fw_setenv boot_wait on fw_setenv uart_en 1 fw_setenv flag_boot_rootfs 0 fw_setenv flag_last_success 1 fw_setenv flag_boot_success 1 fw_setenv flag_try_sys1_failed 8 fw_setenv flag_try_sys2_failed 8 fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata), 2048k(factory),2048k(fip),256k(crash),256k(crash_log), 34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)" ``` 6. Flash stock-squashfs-sysupgrade.bin Use shell command: `sysupgrade -n /tmp/stock-squashfs-sysupgrade.bin` Or go to luci web. If you need to change to Openwrt U-Boot layout, do next. If you do not need, please ignore it. Change to OpenWrt U-Boot: 1. Flash ubootmod-initramfs-factory.ubi Check mtd partitions: `cat /proc/mtd` ``` mtd7: 00040000 00020000 "KF" mtd8: 02200000 00020000 "ubi_kernel" mtd9: 04e00000 00020000 "ubi" ``` Run following command: `ubiformat /dev/mtd8 -y -f /tmp/ubootmod-initramfs-factory.ubi` Then reboot your router, it should boot to the openwrt initramfs system now. 2. Check mtd again ``` mtd7: 00040000 00020000 "KF" mtd8: 07000000 00020000 "ubi" ``` Make sure mtd8 is ubi. 3. Install kmod-mtd-rw Run command: `opkg update && opkg install kmod-mtd-rw` Or get it in openwrt server, or build it yourself, then install it manually Then run this command: `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Clean up pstore Run Command: `rm -f /sys/fs/pstore/*` 5. Format ubi and create new ubootenv volume ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB ``` 6. (Optional) Add recovery boot feature. ``` ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 /tmp/ubootmod-initramfs-recovery.itb ``` 7. Flash Openwrt U-Boot ``` mtd write /tmp/ubootmod-preloader.bin BL2 mtd write /tmp/ubootmod-bl31-uboot.fip FIP ``` 6. Flash ubootmod-squashfs-sysupgrade.itb Use shell command: `sysupgrade -n /tmp/ubootmod-squashfs-sysupgrade.itb` Or go to luci web. Now everything is done, Enjoy! Go Back to stock from Openwrt U-Boot: 1. Force flash ubootmod-initramfs-recovery.itb Use shell command: `sysupgrade -F -n /tmp/ubootmod-initramfs-recovery.itb` Or go to luci web. Then it should boot to the openwrt initramfs system now. 2. Format ubi and Nvram ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 mtd erase Nvram ``` 3. Install kmod-mtd-rw Run command: `opkg update && opkg install kmod-mtd-rw` Or get it in openwrt server, or build it yourself, then install it manually Then run this command: `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Flash stock U-Boot and ubi ``` mtd write /tmp/BL2.bin BL2 mtd write /tmp/FIP.bin FIP mtd write /tmp/ubi.bin ubi ``` Then reboot your router, waiting it finished rollback in minutes. Go Back to stock from stock layout Openwrt: Just run command: `ubiformat /dev/mtd8 -y -f /tmp/ubi.bin` Then reboot your router, waiting it finished rollback in minutes. Notes: 1. Openwrt U-Boot and ubootmod openwrt did not enable NMBM. Please make your backup safe. Signed-off-by: Hank Moretti <mchank9999@gmail.com>
This commit is contained in:
Hank Moretti
Hauke Mehrtens
parent
20603e764d
commit
54dc1cde48
@ -0,0 +1,34 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
#include "mt7981b-xiaomi-mi-router-wr30u.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Xiaomi Mi Router WR30U (stock layout)";
|
||||
compatible = "xiaomi,mi-router-wr30u-stock", "mediatek,mt7981";
|
||||
};
|
||||
|
||||
&spi_nand {
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
};
|
||||
|
||||
&partitions {
|
||||
// ubi_kernel is the ubi partition in stock.
|
||||
partition@600000 {
|
||||
label = "ubi_kernel";
|
||||
reg = <0x600000 0x2200000>;
|
||||
};
|
||||
|
||||
/* ubi is the result of squashing
|
||||
* consecutive stock partitions:
|
||||
* - ubi1
|
||||
* - overlay
|
||||
* - data
|
||||
*/
|
||||
partition@2800000 {
|
||||
label = "ubi";
|
||||
reg = <0x2800000 0x4e00000>;
|
||||
};
|
||||
};
|
||||
@ -0,0 +1,16 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
#include "mt7981b-xiaomi-mi-router-wr30u.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Xiaomi Mi Router WR30U (OpenWrt U-Boot layout)";
|
||||
compatible = "xiaomi,mi-router-wr30u-ubootmod", "mediatek,mt7981";
|
||||
};
|
||||
|
||||
&partitions {
|
||||
partition@600000 {
|
||||
label = "ubi";
|
||||
reg = <0x600000 0x7000000>;
|
||||
};
|
||||
};
|
||||
249
target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u.dtsi
Normal file
249
target/linux/mediatek/dts/mt7981b-xiaomi-mi-router-wr30u.dtsi
Normal file
@ -0,0 +1,249 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
led-boot = &led_system_yellow;
|
||||
led-failsafe = &led_system_yellow;
|
||||
led-running = &led_system_blue;
|
||||
led-upgrade = &led_system_yellow;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x10000000>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
mesh {
|
||||
label = "mesh";
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_9>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_system_blue: system_blue {
|
||||
label = "blue:system";
|
||||
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_system_yellow: system_yellow {
|
||||
label = "yellow:system";
|
||||
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_network_blue {
|
||||
label = "blue:network";
|
||||
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_network_yellow {
|
||||
label = "yellow:network";
|
||||
gpios = <&pio 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
nvmem-cells = <&macaddr_factory_4>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
mac-address-increment = <(-1)>;
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
switch: switch@0 {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <31>;
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand: flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-buswidth = <4>;
|
||||
spi-rx-buswidth = <4>;
|
||||
|
||||
partitions: partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x00 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "Nvram";
|
||||
reg = <0x100000 0x40000>;
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "Bdata";
|
||||
reg = <0x140000 0x40000>;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x200000>;
|
||||
read-only;
|
||||
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
reg = <0x4 0x6>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "crash";
|
||||
reg = <0x580000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5c0000 {
|
||||
label = "crash_log";
|
||||
reg = <0x5c0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7600000 {
|
||||
label = "KF";
|
||||
reg = <0x7600000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
@ -20,6 +20,10 @@ netgear,wax220)
|
||||
ucidef_set_led_netdev "wlan2g" "WLAN2G" "blue:wlan2g" "phy0-ap0"
|
||||
ucidef_set_led_netdev "wlan5g" "WLAN5G" "blue:wlan5g" "phy1-ap0"
|
||||
;;
|
||||
xiaomi,mi-router-wr30u-stock|\
|
||||
xiaomi,mi-router-wr30u-ubootmod)
|
||||
ucidef_set_led_netdev "wan" "wan" "blue:network" "wan"
|
||||
;;
|
||||
xiaomi,redmi-router-ax6000-stock|\
|
||||
xiaomi,redmi-router-ax6000-ubootmod)
|
||||
ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan"
|
||||
|
||||
@ -49,6 +49,8 @@ mediatek_setup_interfaces()
|
||||
tplink,tl-xdr6086)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2" eth1
|
||||
;;
|
||||
xiaomi,mi-router-wr30u-stock|\
|
||||
xiaomi,mi-router-wr30u-ubootmod|\
|
||||
xiaomi,redmi-router-ax6000-stock|\
|
||||
xiaomi,redmi-router-ax6000-ubootmod)
|
||||
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" wan
|
||||
@ -94,6 +96,8 @@ mediatek_setup_macs()
|
||||
wan_mac=$(macaddr_add "$lan_mac" 1)
|
||||
label_mac=$wan_mac
|
||||
;;
|
||||
xiaomi,mi-router-wr30u-stock|\
|
||||
xiaomi,mi-router-wr30u-ubootmod|\
|
||||
xiaomi,redmi-router-ax6000-stock|\
|
||||
xiaomi,redmi-router-ax6000-ubootmod)
|
||||
wan_mac=$(mtd_get_mac_ascii Bdata ethaddr_wan)
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
REQUIRE_IMAGE_METADATA=1
|
||||
|
||||
redmi_ax6000_initial_setup()
|
||||
xiaomi_initial_setup()
|
||||
{
|
||||
# initialize UBI and setup uboot-env if it's running on initramfs
|
||||
[ "$(rootfs_type)" = "tmpfs" ] || return 0
|
||||
@ -35,7 +35,15 @@ redmi_ax6000_initial_setup()
|
||||
fw_setenv flag_boot_success 1
|
||||
fw_setenv flag_try_sys1_failed 8
|
||||
fw_setenv flag_try_sys2_failed 8
|
||||
fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),30720k(ubi),30720k(ubi1),51200k(overlay)"
|
||||
|
||||
local board=$(board_name)
|
||||
case "$board" in
|
||||
xiaomi,mi-router-wr30u-stock)
|
||||
fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)"
|
||||
xiaomi,redmi-router-ax6000-stock)
|
||||
fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),30720k(ubi),30720k(ubi1),51200k(overlay)"
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
platform_do_upgrade() {
|
||||
@ -79,10 +87,12 @@ platform_do_upgrade() {
|
||||
tplink,tl-xdr4288|\
|
||||
tplink,tl-xdr6086|\
|
||||
tplink,tl-xdr6088|\
|
||||
xiaomi,mi-router-wr30u-ubootmod|\
|
||||
xiaomi,redmi-router-ax6000-ubootmod)
|
||||
CI_KERNPART="fit"
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
xiaomi,mi-router-wr30u-stock|\
|
||||
xiaomi,redmi-router-ax6000-stock)
|
||||
CI_KERN_UBIPART=ubi_kernel
|
||||
CI_ROOT_UBIPART=ubi
|
||||
@ -135,8 +145,9 @@ platform_pre_upgrade() {
|
||||
local board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
xiaomi,mi-router-wr30u-stock|\
|
||||
xiaomi,redmi-router-ax6000-stock)
|
||||
redmi_ax6000_initial_setup
|
||||
xiaomi_initial_setup
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
@ -365,6 +365,51 @@ define Device/tplink_tl-xdr6088
|
||||
endef
|
||||
TARGET_DEVICES += tplink_tl-xdr6088
|
||||
|
||||
define Device/xiaomi_mi-router-wr30u-stock
|
||||
DEVICE_VENDOR := Xiaomi
|
||||
DEVICE_MODEL := Mi Router WR30U (stock layout)
|
||||
DEVICE_DTS := mt7981b-xiaomi-mi-router-wr30u-stock
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
|
||||
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
|
||||
ARTIFACTS := initramfs-factory.ubi
|
||||
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel
|
||||
endif
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += xiaomi_mi-router-wr30u-stock
|
||||
|
||||
define Device/xiaomi_mi-router-wr30u-ubootmod
|
||||
DEVICE_VENDOR := Xiaomi
|
||||
DEVICE_MODEL := Mi Router WR30U (OpenWrt U-Boot layout)
|
||||
DEVICE_DTS := mt7981b-xiaomi-mi-router-wr30u-ubootmod
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
|
||||
KERNEL_IN_UBI := 1
|
||||
UBOOTENV_IN_UBI := 1
|
||||
IMAGES := sysupgrade.itb
|
||||
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
|
||||
KERNEL := kernel-bin | gzip
|
||||
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
||||
IMAGE/sysupgrade.itb := append-kernel | \
|
||||
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
|
||||
ARTIFACTS := preloader.bin bl31-uboot.fip
|
||||
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
|
||||
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot xiaomi_mi-router-wr30u
|
||||
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
|
||||
ARTIFACTS += initramfs-factory.ubi
|
||||
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
|
||||
endif
|
||||
endef
|
||||
TARGET_DEVICES += xiaomi_mi-router-wr30u-ubootmod
|
||||
|
||||
define Device/xiaomi_redmi-router-ax6000-stock
|
||||
DEVICE_VENDOR := Xiaomi
|
||||
DEVICE_MODEL := Redmi Router AX6000 (stock layout)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user