Qualcomm SSDK is driver for Qualcomm Atheros switches and PHY-s.
It is quite complicated and used by rest of the Qualcomm SDK stack for
anything switch or PHY related.
It is required for IPQ807x support as currently, there is no better driver
for the built-in switch or UNIPHY.
So, lets add the fixed-up version that supports kernel 5.15 for use on
ipq807x target until a better driver is available.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is the follow up to the PCI support commit now providing support for
AHB variant as well, though currently only for ipq807x as that is only
OpenWrt supported SoC ath11k supports as well.
Currently, we are disabling coldboot calibration on ipq807x as it does not
work, there is a remoteproc bug that makes it come late out of reset so
disable coldboot until that is fixed.
Also, as ath11k is quite memory hungry, we are introducing a config option
to use the limits for 512MB of RAM, similar to what QCA does downstream but
in way simpler and cleaner way so that 512MB save some RAM.
512MB profile is also set as the default for now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
* 5G: 2x2/80MHz (IPQ8070A)
* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)
Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.
SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a temporary workaround for supporting multiple cards or AHB+PCI.
There is ongoing upstream work to properly support this based of
advertised FW features, but that is still ongoing.
This is only supported on QCN9074 cards due to FW limitation, so HW ID
is checked in order to prevent breaking QCA6390 and other popular cards.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package ath11k firmware for AHB devices as well as QCN9074 which is a non
consumer card targeted as a companion for QCA WiSoC-s.
linux-firmware is always out of date for these, so fetch them from Kalle-s
repo like we do for ath10k.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.
Specifications
--------------
SOC : Mediatek MT7621AT
ETH : Two 1 gigabit ports, built into the SOC
WIFI : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED : Power (green+red)
LED : WiFi (green+blue)
LED : WPS (green+red)
LED : Followme (green+red)
Power : 12 VDC, 1A barrel plug
Winbond variant:
RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1
Macronix variant:
RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1
Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.
The pinout is: VCC (the square), RX, TX, GND.
Installation
------------
See the Wiki page [1] for more details, it comes down to:
1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
environment located at 0x30000
Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.
MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use | address | example |
+----------+------------------+-------------------+
| Device | label | 00:00:00:11:00:00 |
| Ethernet | + 3 | 00:00:00:11:00:03 |
| 2g | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g | + 1 | 00:00:00:11:00:01 |
+----------+------------------+-------------------+
The label address is stored in ASCII in the board_data partition
Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
both partitions for more storage space.
Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
macaddr_add
- Only the power LED is configured by default
References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
SOC: Qualcomm IPQ4019
WiFi 1: QCA4019 IEEE 802.11b/g/n
WiFi 2: QCA4019 IEEE 802.11a/n/ac
WiFi 3: QCA8888 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet: Qualcomm Atheros QCA8072 (2-port)
Flash 1: Mactronix MX30LF4G18AC-XKI
RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB)
LED Controller: NXP PCA9633 (I2C)
Buttons: Single reset button (GPIO).
- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.
Bluetooth:
========
- Fully working with the following caveats:
- RFKILL need to be enabled in the kernel.
- An older version of bluez is needed as bccmd is needed to configure the chip.
Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.
Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.
The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.
It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software )
Installation
1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :
VCC (3.3V). Do not use unless you need to source power for the converer from it.
TX
RX
GND
Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.
2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
3.Connect TFTP server to RJ-45 port (WAN/LAN1).
4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
bootm 0x84000000
5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:
WEB PARITION
cat /dev/mtd8 > /tmp/mtd8.bin
scp /tmp/mtd8.bin root@YOURSERVERIP:/
rm /tmp/mtd8.bin
ROOT PARITION
cat /dev/mtd9 > /tmp/mtd9.bin
scp /tmp/mtd9.bin root@YOURSERVERIP:/
rm /tmp/mtd9.bin
If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000
6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it
7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin
previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.
Back to Stock (!!! need original dump taken from initramfs !!!) -------------
Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000
This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000
After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router
As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
| J2
|
+--- Don't connect
Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
pressing 't'
3. Load and run OpenWrt initramfs image:
tftpboot
bootm
4. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
the OEM firmware
MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
| | MAC example 1 | MAC example 2 | Algorithm |
+---------+-------------------+-------------------+-------------+
| label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).
Notes
-----
[1] WAN MAC address:
a. First octet of WAN MAC is differ than others and OUI is not related
to TP-Link company. This probably should be fixed.
b. Flipping bits in first octet and hex delta are different for the
different MAC examples:
+-----------------+----------------+----------------+
| | Example 1 | Example 2 |
+-----------------+----------------+----------------+
| LAN | 68 = 0110 1000 | 50 = 0101 0000 |
| MAC (1st octet) | ^ ^ ^ | |
+-----------------+----------------+----------------+
| WAN | 72 = 0111 0010 | 54 = 0101 0100 |
| MAC (1st octet) | ^ ^ ^ | ^ |
+-----------------+----------------+----------------+
| HEX delta | 0xa | 0x4 |
+-----------------+----------------+----------------+
| DEC delta | 4 | 4 |
+-----------------+----------------+----------------+
c. DEC delta is a constant (4). This looks like a mistake in OEM
firmware and probably should be fixed.
Based on the above, I decided to keep correct OUI and make WAN MAC =
label + 1.
[2] Bootloaders
The device contains 3 bootloaders:
- First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
located on NAND Flash to load next full-feature Uboot.
- Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
bootloader includes recovery webserver. Requires special uImages to
continue the boot process:
0x00 (os0, os1) - firmware uImage
0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
- Additionally, both slots of the original TP-Link firmware contains
Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
magics and CRCs. We don't use this U-Boot with OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Support for MT7981 and MT7986 has been merged, remove patches.
Tested on a couple of MT7986, MT7622 and MT7623 boards.
MIPS builds are untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, ath11k will crash the crash if we try to bringup the monitor
mode interface.
Luckily, it has already been fixed upstream, so backport the patches
fixing it.
Fixes: 93ae4353cd ("mac80211: add ath11k PCI support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is currently a problem with making reproducible version of lldpd.
The tool version is generated based on 3 source:
1. .dist-version file in release tar
2. git hash with presence of .git directory
3. current date
Using the codeload tar from github results in getting the repo without
the .git directory and since they are not release tar, we don't have
.dist-version. This results in having lldpd bin with a version set to
the current build time.
Switch to release tar so that we correctly have a .dist-version file and
the version is not based on the build time.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
This fixes a security problem in ksmbd. It currently has the
ZDI-CAN-18259 ID assigned, but no CVE yet.
Backported from:
8824b7af40cc4f3b5a6a
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The bpf plugin provides functionality for loading and interacting with
eBPF modules.
It allows loading full modules and pinned maps/programs and supports
interacting with maps and attaching programs as tc classifiers.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
34cfbb922c96 README.md: various spelling and documentation fixes
ff32355ea645 build: make rtnl/nl80211 depend on linux instead of !APPLE
c0e413c21f7b include: add uc_fn_thisval()
1e4d20932646 Merge pull request #134 from nbd168/thisval
Signed-off-by: Felix Fietkau <nbd@nbd.name>
GCC 12.2.0 shows these error messages:
````
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c: In function 'rtw_mfree_stainfo':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:210:24: error: the comparison will always evaluate as 'true' for the address of 'lock' will never be NULL [-Werror=address]
210 | if(&psta->lock != NULL)
| ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:109,
from rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:22:
rtl8812au-ct-2021-11-07-39df5596/include/sta_info.h:95:17: note: 'lock' declared here
95 | _lock lock;
| ^~~~
````
````
CC [M] rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.o
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c: In function 'cfg80211_rtw_scan':
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:2176:32: warning: the comparison will always evaluate as 'true' for the address of 'ssid' will never be NULL [-Waddress]
2176 | if(ssids->ssid != NULL
| ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service_linux.h:88,
from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service.h:41,
from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:32,
from rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:22:
/home/hauke/openwrt/openwrt/staging_dir/target-mips_24kc_musl/usr/include/mac80211/net/cfg80211.h:2364:12: note: 'ssid' declared here
2364 | u8 ssid[IEEE80211_MAX_SSID_LEN];
| ^~~~
````
````
CC [M] rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.o
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c: In function 'phydm_cmd_parser':
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:873:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
873 | if(input[i+1]) {
| ^~~~~
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:894:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
894 | if(input[i+1]) {
| ^~~~~
````
This one was only seen on the rockchip/armv8 target:
````
CC [M] rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.o
In function '__nat25_add_pppoe_tag',
inlined from 'nat25_db_handle' at rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:909:10:
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:118:9: error: 'memcpy' reading between 2052 and 9220 bytes from a region of size 40 [-Werror=stringop-overread]
118 | memcpy((unsigned char *)ph->tag, tag, data_len);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c: In function 'nat25_db_handle':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:878:63: note: source object 'tag_buf' of size 40
878 | unsigned char tag_buf[40];
| ^~~~~~~
````
Most of them are looking like real errors to me, but some fixes need a
deeper understanding of the driver and probably bigger changes to the driver.
Ignore these error messages for now. It would be nice if someone would
fix them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
GCC 12.2.0 shows this false positive error message:
````
uqmi-2022-05-04-56cb2d40/dev.c: In function 'qmi_request_wait':
uqmi-2022-05-04-56cb2d40/dev.c:217:23: error: storing the address of local variable 'complete' in '*req.complete' [-Werror=dangling-pointer=]
217 | req->complete = &complete;
| ~~~~~~~~~~~~~~^~~~~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'complete' declared here
208 | bool complete = false;
| ^~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'req' declared here
cc1: all warnings being treated as errors
````
and this one:
````
In file included from uqmi-2022-05-04-56cb2d40/commands.c:28:
In function 'blobmsg_close_table',
inlined from 'cmd_nas_get_cell_location_info_cb' at /home/haukeuqmi-2022-05-04-56cb2d40/commands-nas.c:897:4:
/usr/include/libubox/blobmsg.h:256:9: error: 'c' may be used uninitialized [-Werror=maybe-uninitialized]
256 | blob_nest_end(buf, cookie);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from uqmi-2022-05-04-56cb2d40/commands.c:169:
uqmi-2022-05-04-56cb2d40/commands-nas.c: In function 'cmd_nas_get_cell_location_info_cb':
uqmi-2022-05-04-56cb2d40/commands-nas.c:713:15: note: 'c' was declared here
713 | void *c, *t, *cell, *freq;
| ^
cc1: all warnings being treated as errors
````
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
GCC 12.2.0 shows this false positive error message:
````
In function 'bigger_buffer',
inlined from '__libdw_gunzip' at gzip.c:374:12:
gzip.c:96:9: error: pointer may be used after 'realloc' [-Werror=use-after-free]
96 | b = realloc (state->buffer, more -= 1024);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
gzip.c:94:13: note: call to 'realloc' here
94 | char *b = realloc (state->buffer, more);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
````
GCC bug report: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=104069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update busybox to version 1.36.0
* refresh patches (remove the backported upstream fix)
* refresh config
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.36.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.36.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* Config-defaults.in: correct the default ports that get reset
BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT 80
BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT 23
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit a few Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The kmod-mt7615-common package does not contain any code that
related to mt7915e Wi-Fi6 driver, so remove it.
Tested on ramips/mt7621: SIM SIMAX1800T
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
A huge rewrite in libpcap was introduced by dc14a7babca1 ("rpcap: have
the server tell the client its byte order.") [0]. The patch
"201-space_optimization.patch" does not apply at all anymore. So remove
it.
Refresh:
- 100-no-openssl.patch
- 102-skip-manpages.patch
Update the "300-Add-support-for-B.A.T.M.A.N.-Advanced.patch" with latest
PR [1].
old ipkg size:
90964 bin/packages/mips_24kc/base/libpcap1_1.10.1-5_mips_24kc.ipk
new ipkg size:
93340 bin/packages/mips_24kc/base/libpcap1_1.10.2-1_mips_24kc.ipk
[0] - dc14a7babc
[1] - https://github.com/the-tcpdump-group/libpcap/pull/980
Signed-off-by: Nick Hainke <vincent@systemli.org>
It's necessary to be able to specify the length
for MAC addresses that are stored in flash, for example,
in a case where it is stored without any delimiter.
Let both offset and length have default values.
Add a sanity check related to partition size.
Also, clean up syntax and unnecessary lines.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This is a MT7621-based device with 128MB NAND flash, 256MB RAM, and a USB port.
The board has headers to attach console. In order for them to work two solder
bridges near those pads need to be made.
The defice has the following partition table:
```
0x000000000000-0x000000080000 : "u-boot"
0x000000080000-0x000000100000 : "u-boot-env"
0x000000100000-0x000000140000 : "factory"
0x000000140000-0x000007e00000 : "firmware"
0x000007e00000-0x000008000000 : "panic-ops"
```
`firmware` partition contains UBI volumes. Unfortunately I accidentally wiped
partition and I no longer have access to it.
`firmware` partition contains 'secondary' U-Boot which is run by 'first' u-boot.
It also contains various configuration partitions that include device info and
MAC address. There also seems to be 'primary' and 'backup' set of 'main' volumes.
U-boot has `mtkupgrade` command that just overrides data on firmware partitions.
Firmware file provided by TP-Link cannot be used with that command.
U-boot also has 'recovery' http server. Unfortunately I was not able to make it
work with manufacturer's firmware.
Manufacturer's firmware essentially contains multiple UBI volumes along with
'partition table'. Unfortunately I no longer can properly run manufacturer's
firmware so I cannot at the moment try to a support for building 'factory' images.
This patch adds support for initramfs image as well as sysupgrade image.
This seems to be pretty standard MT7621 board otherwise.
Things that work:
* network
* leds
* usb
* factory MAC detection
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
def7755c459d add missing copyright headers
f68307fd96d7 add hairpin mode support
9ee8f433ba4e nl: do not pass NDA_VLAN with vid=0
978c1f9eed07 add support for the bridge port isolated flag
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ABI of the wolfssl library changed a bit between version 5.5.3 and
5.5.4. This release update will trigger a rebuild of all packages which
are using wolfssl to make sure they are adapted to the new ABI.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This converts the trusted firmware arm build Makefile to make use of
the common trusted-firmware-a.mk file. This also fixes the build with
binutils 2.39.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without these changes it used the system LDFLAGS for the compilation of
the cryptopp library. This does not always work when we add
"-no-warn-rwx-segments" which is done to support binutils 2.39 inside of
OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make use of the definitions from trusted-firmware-a.mk to build the
Trusted firmware arm. This fixes the build with binutils 2.39.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is used to access footer data in firmare files, and is simpler and
less error-prone than using 'dd' with calculated offsets.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update the board name defined in DTS to match online documentation and the
name encoded into factory firmware. This helps supports flashing firmware
factory images using 'sysupgrade'.
Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB
instead of the correct 74 MB, and defines factory images which include
extra adjustments/padding that do not match OEM factory images and may
cause problems flashing. Update image size and build recipe to fix these.
Suggested-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/v2.28.2
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.
Fixes the following CVEs:
* CVE-2022-46393: Fix potential heap buffer overread and overwrite in
DTLS if MBEDTLS_SSL_DTLS_CONNECTION_ID is enabled and
MBEDTLS_SSL_CID_IN_LEN_MAX > 2 * MBEDTLS_SSL_CID_OUT_LEN_MAX.
* CVE-2022-46392: An adversary with access to precise enough information
about memory accesses (typically, an untrusted operating system
attacking a secure enclave) could recover an RSA private key after
observing the victim performing a single private-key operation if the
window size used for the exponentiation was 3 or smaller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2cffe0c44e62 treewide: correctly apply IFNAMSIZ limit
96bcbb2e4eb6 wireless: allow set_retry ubus notify command to trigger a wdev restart
a2e8cd75dbf6 wireless: add support for disabling multicast-to-unicast per virtual interface
e9f44189ade7 system: move netdev types to system-linux.c where they are used
a3fab0119ef1 utils: include utils.h last
7ce73fc16765 vlandev: propagate topology changes
81c1fbcba2f2 device: fix vlan device issues with disappearing lower devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The libraries libpthread, libdl, libutil, libanl have been integrated
into the libc library in version 2.34. it is not needed to explicitly
link them any more.
Most of the functions have been moved from the librt.so into libc.so
some time ago already.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It has been brought to my attention that recently added WCN6855 firmware
is broken as it is getting stripped during building due to being 2 ELF
binaries.
I am sure WCN6750 and any other ELF binaries are having the same issue,
so since stripping firmware binaries is clearly unwanted disable it.
Fixes: b4d3694f81 ("linux-firmware: package ath11k consumer cards firmware")
Signed-off-by: Robert Marko <robimarko@gmail.com>
U-Boot flash instructions:
0. OpenWrt U-Boot does not support stock layout, it comes with recovery
boot support, automatic tftp recovery and never blocks UART.
A new flash layout is introduced, we call it OpenWrt U-Boot layout,
stock flash layout and the old OpenWrt layout are not supported.
During the whole flash procedure, please do not reboot or power off
unless requested explicitly, or you will break your device.
1. Your device should already running OpenWrt.
If not, follow the instructions to flash OpenWrt:
https://github.com/openwrt/openwrt/pull/11115
2. Backup BL2 Nvram Bdata Factory and FIP in case you break something or
in case you want to go back to stock firmware one day.
cat /dev/mtdblock0 > /tmp/BL2.bin
cat /dev/mtdblock1 > /tmp/Nvram.bin
cat /dev/mtdblock2 > /tmp/Bdata.bin
cat /dev/mtdblock3 > /tmp/Factory.bin
cat /dev/mtdblock4 > /tmp/FIP.bin
And save all whose bin files to somewhere safe.
Then backup your configurations, since ubiformat for entire mtd device is
required to create new ubootenv volume for OpenWrt U-Boot.
3. Run the following cmd to boot into an initramfs with the new OpenWrt
U-Boot layout that expand ubi partion to the end of flash:
ubiformat /dev/mtd7 -y -f /tmp/ax6000-ubootmod-initramfs-factory.ubi
4. After boot into initramfs, check mtd partion info.
The ubi partion should be mtd5
root@OpenWrt:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 BL2
mtd1: 00040000 00020000 Nvram
mtd2: 00040000 00020000 Bdata
mtd3: 00200000 00020000 Factory
mtd4: 00200000 00020000 FIP
mtd5: 07a80000 00020000 ubi
5. Load kmod-mtd-rw to temporarily make the bootloader partions writable.
The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory
by default.
To install kmod-mtd-rw via opkg:
opkg update && opkg install kmod-mtd-rw
Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually
e.g:
https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/
Select your OpenWrt release version and kernel version accordingly.
Load kmod-mtd-rw:
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1
6. Run the following cmd to clean all pending crash dumps in pstore,
or OpenWrt U-Boot may boot into NAND recovery or tftp recovery.
rm -f /sys/fs/pstore/*
7. Format ubi and create new ubootenv volume:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
8. This is optional. Skip this if you do not want to have NAND recovery
boot feature offered by OpenWrt U-Boot. Don't worry, you always have
automatic tftp recovery feature enabled.
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/ax6000-ubootmod-initramfs-recovery.itb
9. Now, flash new U-Boot. Bye-bye ugly stock U-Boot.
mtd write /tmp/ax6000-ubootmod-preloader.bin BL2
mtd write /tmp/ax6000-ubootmod-bl31-uboot.fip FIP
10. Flash the squashfs-sysupgrade.bin as usual:
sysupgrade -n /tmp/ax6000-ubootmod-squashfs-sysupgrade.itb
Enjoy!
Signed-off-by: Furong Xu <xfr@outlook.com>
WCN6855 exists in 2 HW revisions, but both use the same FW so upstream
just has a symlink for hw2.1 to hw2.0 that I forgot to make.
Fixes: b4d3694f81 ("linux-firmware: package ath11k consumer cards firmware")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adds uboot-envtools support for ramips Asus RX-AX53U now that partition
can be correctly read.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
libpath.so uses host path in ld script causing other packages fail to
cross compile, e.g. perl:
"ld: cannot find /usr/lib/libbsd.so.0.11.6: No such file or directory"
Fixes: openwrt/packages#19390
Signed-off-by: Xuefer H <xuefer@gmail.com>
Most relevant feature for openwrt in this release, supports dynamically
removing hosts from 'hostsdir' supplied host files.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Ensure the MAC address for all NanoPi R1 boards is assigned uniquely for
each board.
The vendor ships the device in two variants; one with and one without
eMMC; but both without static mac-addresses.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S and R4S in case the EEPROM
chip is not present by generating the board MAC from the SD card CID.
[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R1#Hardware_Spec
Similar too and based on:
commit b5675f500d ("rockchip: ensure NanoPi R4S has unique MAC address")
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
brcmsmac needs bcma. bcma is build into the kernel for the other bcm47xx
subtargets, but not for the legacy target because it only uses ssb. We
could build bcma as a module for bcm47xx_legacy, but none of these old
devices uses a wifi card supported by brcsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Several sunxi devices come with multiple mmc devices. On such devices,
the mmc device order is unpredictable, so using /dev/mmcblk0p2 as root
device doesn't always work, which results in unbootable devices.
For the Banana Pi BPI-R3 in the mediatek target, this has been solved by
defining aliases for the mmc devices in the DTS. Ideally we would do the
same here, but for sunxi-a64 we already use UUID probing, so let's start
with that (5f2ff607e2 ("uboot-sunxi: a64: allow booting directly from
eMMC")).
Since we're building and including u-boot in each supported device
image, and this method has been proven to work fine for a64, let's just
change the default u-boot env file to do the same.
Fixes: #10080
Fixes: e6d9f6fdff ("sunxi: add support for FriendlyARM NanoPi R1")
Co-authored-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
[use UUID in default u-boot env, rewrite commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Changes since v1.2.8:
32aaf32 libxdp: Fix incorrect rx_ring_setup_done
6049671 headers: add bpf_endian.h for parsing_helpers.h
2682c1c export-man: Ignore errors when executing git shell command
8afda7a xdp-loader/README: Mention lack of support for HW mode in most cards
dc69919 libxdp: fix prog_fd checks for fd >= 0
3d7c22a libxdp: Allow falling back to single-program attachment for loaded programs
af00429 libxdp: Fix check in xdp_program__attach_single()
41703d2 libxdp: Make sure to set the the program autoload when loading a program
b1fd2e5 test-xdpdump: Only run tshark attribute test on newer versions of tshark
5dfe342 libxdp: Convert xdp-dispatcher to use strict section names
929a22e configure: Try to auto-detect versioned clang binaries
074fcfb libxdp: Check program name when determining if a program is a dispatcher
e13a191 Bump TOOLS_VERSION to 1.2.9
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ath11k is the upstream driver for Qualcomm 802.11ax radios, both for the
internal AHB and PCI based cards.
This commit does however only provide PCI support while AHB will follow
but its SoC specific so it will require an OpenWrt target first.
It differs a bit from ath10k as it requires stuff like QRTR, MHI and QMI
helpers.
PCI variant requires qrtr-mhi and mhi-bus which backports do provide,
however we are dropping those in a patch as they will conflict with
support for the AHB variant as that one requires qrtr-smd which in turn
requires RPMSG and GLINK and its not feasable to provide those in
backports as they are really SoC specific.
QRTR and MHI in kernel 5.10 are not usable and backporting the changes
is not easy as they have changed drastically from 5.10 to 5.15 ath11k will
only be available on targets that use kernel 5.15.
Signed-off-by: Robert Marko <robimarko@gmail.com>
QRTR is Qualcomm IPC router protocol and ath11k requires it for both
AHB and PCI support, so package it as a kernel module so it can be
added as a dependency to the ath11k module.
Only kernel 5.15 is currently supported due to various things missing in
5.10 whose backporting is out of scope for this patch.
SMD, TUN and MHI variants are packaged.
SMD variant depends on the ipq807x
target as it has dependency on the RPMSG drivers which are Qualcomm
and SoC specific anyway.
Signed-off-by: Robert Marko <robimarko@gmail.com>
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A
Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
"Administration/Management/Firmware update/Choose File" in vendor's
web interface (ip: 192.168.1.10, login: Admin, password: Admin).
Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
file by "System/Backup/Flash Firmware/Flash image..." in
LuCI web interface (ip: 192.168.1.1, login: root, no password).
Wait ~240 seconds.
Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing
Signed-off-by: Alexey Bartenev <41exey@proton.me>
libxxhash is now available in the OpenWrt package feed and gdb will link
against it if gdb finds this library. Explicitly deactivate the usage
of xxhash.
This should fix the build of gdb in build bots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The compatible in the device tree is "haoyu,a10-marsboard",
modify the board_name to keep it consistent.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Make use of KERNEL_MAKE in kernel packages were easily possible.
This moves some more code to common places and reduces the number of
lines.
It is defined like this:
KERNEL_MAKE = $(MAKE) $(KERNEL_MAKEOPTS)
KERNEL_MAKEOPTS = -C $(LINUX_DIR) $(KERNEL_MAKE_FLAGS)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.
1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
be helpful for users who may forget to do this before sysupgrade in
the initramfs.
New flash instructions:
1. Gain ssh access. Please refer to:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)
2. Check which system current u-boot is loading from:
COMMAND: `cat /proc/cmdline`
sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
if firmware=1, current system is ubi1
if firmware=0, current system is ubi0
3. Setup nvram and write the firmware:
If the current system is ubi1, please set it up so that the next time
it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
If the current system is ubi, please set it up so that the next time
it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```
4. After rebooting, the system should now boot into the openwrt initramfs.
Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.
For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:
1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```
2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
There are some devices putting kernel and rootfs on separated
ubi volumes. To make OpenWrt compatible with their bootloader,
we need to put kernel and rootfs into separated ubi volumes.
Add support for CI_KERN_UBIPART and CI_ROOT_UBIPART for this
situation.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
split ubi reformat/attach into nand_attach_ubi in preparation
for reusing this code in other functions.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Two WS2812B (NeoPixel) clones are used in Xiaomi Redmi AX6000 as
indicator lights. Add a driver for controlling it using SPI MOSI.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
When reloading modules and running wifi, a phy can sometimes be renamed
while in the middle of a hotplug call that tries to detect new phys
This can lead to bogus wifi-device sections being created
Signed-off-by: Felix Fietkau <nbd@nbd.name>
8d15809 cli: print current HT mode
8f86dd6 cli: use IWINFO_HTMODE_COUNT
f36b72b cli: use IWINFO_KMGMT_NAMES
91be7e0 cli: use IWINFO_CIPHER_NAMES
49b6ec9 cli: fix printing the scan channel width
b1c8873 cli: fix marking the active channel
9e14e64 utils: add iwinfo_band2ghz() and iwinfo_ghz2band() helpers
e084781 utils: add helper functions to get names by values
d09a77a utils: add iwinfo_htmode_is_{ht|vht|he} helpers
8752977 utils: add and use iwinfo_format_hwmodes()
02f433e lib: add IWINFO_80211_COUNT and IWINFO_80211_NAMES
1d30df1 lib: add IWINFO_BAND_COUNT and IWINFO_BAND_NAMES
aefd0ef lib: use common IWINFO_CIPHER_NAMES strings
a5b30de lib: add IWINFO_OPMODE_COUNT and use it for IWINFO_OPMODE_NAMES
9f29e79 lib: constify and fixup the string array definitions
fddc015 nl80211: mark frequencies where HE operation in not allowed
6d50a7c nl80211: add support for HE htmodes
4ba5713 nl80211: properly get available bands for the hwmode
91b2ada nl80211: update the kernel header nl80211.h
3f619a5 nl80211: fix frequency/channel conversion for the 6G band
a77d915 nl80211: don't guess if a name is an ifname
c27ce71 devices: add usb device MediaTek MT7921AU
14f864e nl80211: add ability to describe USB devices
a5a75fd nl80211: remove ancient wpa_supplicant ctrl socket path
dd4e1ff nl80211: fix wpa supplicant ctrl socket permissions
d638163 fix -Wdangling-else warnings
4aa6c5a fix -Wreturn-type warning
3112726 fix -Wpointer-sign warning
ebd5f84 fix -Wmaybe-uninitialized warning
5469898 fix -Wunused-variable warnings
462b679 fix -Wduplicate-decl-specifier warnings
ccaabb4 fix -Wformat-truncation warnings
50380db enable useful compiler warnings via -Wall
Fixes: https://github.com/openwrt/openwrt/issues/10158
Fixes: https://github.com/openwrt/openwrt/issues/10687
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface under admin account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following line:
<PARAMETER name="Password" type="string" value="<your router serial \
is here>" writable="1" encryption="1" password="1"/>
5. Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
ETxxxxxxxxxx is the serial number from the backplate label)
9. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:50 |
| WAN | label + 11 | *:5b |
| 2g | label + 2 | *:52 |
| 5g | label + 3 | *:53 |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
hostapd's compile time option CONFIG_IEEE80211N was removed almost 3 years
ago, 80.211n/HT is always included since then.
Noticed because `hostapd -v11n` confusingly returned an error.
See hostapd's commit:
f3bcd69603 "Remove CONFIG_IEEE80211N build option"
Signed-off-by: Andre Heider <a.heider@gmail.com>
eee80211_frequency_to_channel() isn't used anymore, which is a leftover from:
2a31e9ca97 "hostapd: add op-class to get_status output"
Signed-off-by: Andre Heider <a.heider@gmail.com>
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config
this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor
Signed-off-by: Tony Butler <spudz76@gmail.com>
Allow registration if the SIM is roaming or partner mode, by adding two
new options to the protocol.
Until now, such registration failed because umbim returns exit codes 4 and
5 for such situations.
Signed-off-by: Julio Gonzalez Gil <git@juliogonzalez.es>
378a9dd libtracefs: version 1.6.2
e6daa60 libtracefs: Add unit test to test mounting of tracefs_{tracing,debug}_dir()
32acbbf libtracefs: Have tracefs_{tracing,debug}_dir() mount {tracefs,debugfs} if not mounted
Signed-off-by: Nick Hainke <vincent@systemli.org>
9217ab4 ustream-openssl: Disable renegotiation in TLSv1.2 and earlier
2ce1d48 ci: fix building with i.MX6 SDK
584f1f6 ustream-openssl: wolfSSL: provide detailed information in debug builds
aa8c48e cmake: add a possibility to set library version
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes CVE-2022-1304:
An out-of-bounds read/write vulnerability was found in e2fsprogs 1.46.5.
This issue leads to a segmentation fault and possibly arbitrary code
execution via a specially crafted filesystem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
700a925 fw4: prevent null access when no ipsets are defined
6443ec7 config: drop input traffic by default
119ee1a ruleset: drop ctstate invalid traffic for masq-enabled zones
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add patch to fix compilation error with USE_CPUID_DEVICE enabled and musl
used as libc. Musl doesn't add limits.h header by default and this is
required if USE_CPUID_DEVICE is used.
The package currently compile because fortify headers include limits.h
by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Raise CONFIG_LMB_MAX_REGIONS to 64 as there are going to be more than
8 (the default value) reserved regions to allow supporting offloading
Wireless-to-Ethernet traffic on MT7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add new UCI list 'addn_mount' allowing the expose additional filesystem
paths to the jailed dnsmasq process. This is useful e.g. in case of
manually configured includes to the configuration file or symlinks
pointing outside of the exposed paths as used by e.g. the safe-search
package in the packages feed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
At this moment LS1012A-FRDM have uncompressed initramfs image.
Error was caused, because gzip extract area overlap image.
Let's change loadaddr and enable gzip initramfs images again.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
FCC ID: A8J-EAP1750H
Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
**Specification:**
- QCA9558 SOC
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16FG
- UART at J10 populated
- 4 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)
**MAC addresses:**
MAC addresses are labeled as ETH, 2.4G, and 5GHz
Only one Vendor MAC address in flash
eth0 ETH *:fb art 0x0
phy1 2.4G *:fc ---
phy0 5GHz *:fd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
NOTE: TFTP is not reliable due to bugged bootloader
set MTU to 600 and try many times
if your TFTP server supports setting block size
higher block size is better.
**Format of OEM firmware image:**
The OEM software of EAP1750H is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
openwrt-ar71xx-generic-eap1750h-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
With this patch you can change the pulse digit time by loading the Lantiq
FXS driver kernel module called ltq-tapi. This is relevant for old
rotaryphones that uses pulsedialing.
The default values are:
30-80ms for the low pulse
30-80ms for the high pulse
300ms for minimum Interdigit time
this is OK but on some Phones it can be usefull to customize the values
If you want to change the values to high and low pulse to 40-90ms and
minimum interdigit time to 400ms
than change /etc/modules.d/20-ltq-tapi to (without linebrakes):
drv_tapi min_digit_low=40 min_digit_high=90 max_digit_low=40 \
max_digit_high=90 min_interdigit=400
Signed-off-by: Jonas Albrecht <plonkbong100@protonmail.com>
The symbolic link introduced in 22e9d8bc89 is wrong.
Fixes: 22e9d8bc89 ("cypress-firmware: use symlink to provide firmware in brcm")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Fix mmc_write_vol hush script used by many boards to avoid timeouts on
slow SD cards:
Instead of erasing a complete partition, only erase blocks for the
to-be-written image when writing to MMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Since all NVRAM files in external repo are now upstreamed and to lower
future maintenance cost, disassociate the package from external source
repo.
All upstream pending NVRAM files shall be stored locally from now on.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[Remove outdated URL, add SPDX-License-Identifier]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
use defaults if no build opts selected
(allows build with defaults when mbedtls not selected and configured)
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
According to commit 6f6c2fb321, AP6335 module used in PICO-PI-IMX7D works
only with firmware from `linux-firmware`. However, firmware from
`cypress-firmware` suite is directly from the chip company (Infineon) and
is actually newer.
Instead of dropping the firmware from Infineon, create a package named
`brcmfmac-firmware-4339-sdio`, and keep the Infineon version of
`cypress-firmware-4339-sdio` around.
This gives us devs the option to choose. Also, it means that
- packages `brcmfmac-firmware-*` uniformly come from `linux-firmware`
- packages `cypress-firmware-*` uniformly come from `cypress-firmware`
so hopefully brings more clarity.
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This is to align the implementation with upstream `linux-firmware`.
Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware`
source repository, their NVRAM is provided through a symbolic link to
NVRAM of another board with an identical wireless design.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This is to align the implementation with upstream `linux-firmware`.
Instead of moving these firmware files to `brcm` subdirectory and changing
their names, leave them in `cypress` subdirectory, keep their names intact
and use symbolic links to provide compatibility with Broadcom FullMAC
driver.
This gives more context to where the firmware comes from.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This is to align the implementation with upstream `linux-firmware`.
Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware`
source repository, their NVRAM is provided through a symbolic link to
NVRAM of another board with an identical wireless design.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
PROVIDES for these packages will cause ambiguity and circular dependency
in planned changes.
For example, if there is a package `brcmfmac-firmware-43455-sdio-rpi-cm4`
that depends on `brcmfmac-firmware-43455-sdio-rpi-4b`, there is no way to
tell which one of below packages the system will go for.
- package named `brcmfmac-firmware-43455-sdio-rpi-4b`
- package named `cypress-nvram-43455-sdio-rpi-4b` that PROVIDES
`brcmfmac-firmware-43455-sdio-rpi-4b`
When ambiguity is unacceptable, PROVIDES (aliases) shall be removed and
packages shall only be used through their exact name.
So remove PROVIDES and keep only CONFLICTS.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Some copper SFP modules come with Marvell's 88E1xxx PHY and need this
module to function. Package it, so users can easily install this PHY
driver and use e.g. FINISAR CORP. FCLF-8521-3-HC SFP.
Without marvell PHY driver:
sfp sfp2: module FINISAR CORP. FCLF-8521-3-HC rev A sn XXXXXXX dc XXXXXX
mt7530 mdio-bus:1f sfp2: validation with support 0000000,00000000,00000000 failed: -22
sfp sfp2: sfp_add_phy failed: -22
With marvell PHY driver:
sfp sfp2: module FINISAR CORP. FCLF-8521-3-HC rev A sn XXXXXXX dc XXXXXX
mt7530 mdio-bus:1f sfp2: switched to inband/sgmii link mode
mt7530 mdio-bus:1f sfp2: PHY [i2c:sfp2:16] driver [Marvell 88E1111] (irq=POLL)
mt7530 mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ruckus ZoneFlex 7025 is a single 2.4GHz radio 802.11n 1x1 enterprise
access point with built-in Ethernet switch, in an electrical outlet form factor.
Hardware highligts:
- CPU: Atheros AR7240 SoC at 400 MHz
- RAM: 64MB DDR2
- Flash: 16MB SPI-NOR
- Wi-Fi: AR9285 built-in 2.4GHz 1x1 radio
- Ethernet: single Fast Ethernet port inside the electrical enclosure,
coupled with internal LSA connector for direct wiring,
four external Fast Ethernet ports on the lower side of the device.
- PoE: 802.3af PD input inside the electrical box.
802.3af PSE output on the LAN4 port, capable of sourcing
class 0 or class 2 devices, depending on power supply capacity.
- External 8P8C pass-through connectors on the back and right side of the device
- Standalone 48V power input on the side, through 2/1mm micro DC barrel jack
Serial console: 115200-8-N-1 on internal JP1 header.
Pinout:
---------- JP1
|5|4|3|2|1|
----------
Pin 1 is near the "H1" marking.
1 - RX
2 - n/c
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw,
but with much less manual steps, and is generally recommended, being
safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
work on some rare versions of stock firmware. A more involved, and
requires installing `mkenvimage` from u-boot-tools package if you
choose to rebuild your own environment, but can be used without
disassembly or removal from installation point, if you have the
credentials.
If for some reason, size of your sysupgrade image exceeds 13312kB,
proceed with method [1]. For official images this is not likely to
happen ever.
[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0x9f040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7025-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7025_fw1_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin
[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
it boots, hold the reset button near Ethernet connectors for 5
seconds.
1. Connect the device to the network. It will acquire address over DHCP,
so either find its address using list of DHCP leases by looking for
label MAC address, or try finding it by scanning for SSH port:
$ nmap 10.42.0.0/24 -p22
From now on, we assume your computer has address 10.42.0.1 and the device
has address 10.42.0.254.
2. Set up a TFTP server on your computer. We assume that TFTP server
root is at /srv/tftp.
3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
frmware is pretty ancient and requires enabling HMAC-MD5.
$ ssh 10.42.0.254 \
-o UserKnownHostsFile=/dev/null \
-o StrictHostKeyCheking=no \
-o MACs=hmac-md5
Login. User is "super", password is "sp-admin".
Now execute a hidden command:
Ruckus
It is case-sensitive. Copy and paste the following string,
including quotes. There will be no output on the console for that.
";/bin/sh;"
Hit "enter". The AP will respond with:
grrrr
OK
Now execute another hidden command:
!v54!
At "What's your chow?" prompt just hit "enter".
Congratulations, you should now be dropped to Busybox shell with root
permissions.
4. Optional, but highly recommended: backup the flash contents before
installation. At your PC ensure the device can write the firmware
over TFTP:
$ sudo touch /srv/tftp/ruckus_zf7025_firmware{1,2}.bin
$ sudo chmod 666 /srv/tftp/ruckus_zf7025_firmware{1,2}.bin
Locate partitions for primary and secondary firmware image.
NEVER blindly copy over MTD nodes, because MTD indices change
depending on the currently active firmware, and all partitions are
writable!
# grep rcks_wlan /proc/mtd
Copy over both images using TFTP, this will be useful in case you'd
like to return to stock FW in future. Make sure to backup both, as
OpenWrt uses bot firmwre partitions for storage!
# tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7025_firmware1.bin -p 10.42.0.1
# tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7025_firmware2.bin -p 10.42.0.1
When the command finishes, copy over the dump to a safe place for
storage.
$ cp /srv/tftp/ruckus_zf7025_firmware{1,2}.bin ~/
5. Ensure the system is running from the BACKUP image, i.e. from
rcks_wlan.bkup partition or "image 2". Otherwise the installation
WILL fail, and you will need to access mtd0 device to write image
which risks overwriting the bootloader, and so is not covered here
and not supported.
Switching to backup firmware can be achieved by executing a few
consecutive reboots of the device, or by updating the stock firmware. The
system will boot from the image it was not running from previously.
Stock firmware available to update was conveniently dumped in point 4 :-)
6. Prepare U-boot environment image.
Install u-boot-tools package. Alternatively, if you build your own
images, OpenWrt provides mkenvimage in host staging directory as well.
It is recommended to extract environment from the device, and modify
it, rather then relying on defaults:
$ sudo touch /srv/tftp/u-boot-env.bin
$ sudo chmod 666 /srv/tftp/u-boot-env.bin
On the device, find the MTD partition on which environment resides.
Beware, it may change depending on currently active firmware image!
# grep u-boot-env /proc/mtd
Now, copy over the partition
# tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1
Store the stock environment in a safe place:
$ cp /srv/tftp/u-boot-env.bin ~/
Extract the values from the dump:
$ strings u-boot-env.bin | tee u-boot-env.txt
Now clean up the debris at the end of output, you should end up with
each variable defined once. After that, set the bootcmd variable like
this:
bootcmd=bootm 0x9f040000
You should end up with something like this:
bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),7168k(rcks_wlan.main),7168k(rcks_wlan.bkup),1280k(datafs),256k(u-boot-env)
mtdids=nor0=ar7100-nor0
bootdelay=2
filesize=52e000
fileaddr=81000000
ethact=eth0
stdin=serial
stdout=serial
stderr=serial
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=192.168.0.1
serverip=192.168.0.2
stderr=serial
ethact=eth0
These are the defaults, you can use most likely just this as input to
mkenvimage.
Now, create environment image and copy it over to TFTP root:
$ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
$ sudo cp u-boot-env.bin /srv/tftp
This is the same image, gzipped and base64-encoded: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7. Perform actual installation. Copy over OpenWrt sysupgrade image to
TFTP root:
$ sudo cp openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin /srv/tftp
Now load both to the device over TFTP:
# tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
# tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin -g 10.42.0.1
Verify checksums of both images to ensure the transfer over TFTP
was completed:
# sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin
And compare it against source images:
$ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin
Locate MTD partition of the primary image:
# grep rcks_wlan.main /proc/mtd
Now, write the images in place. Write U-boot environment last, so
unit still can boot from backup image, should power failure occur during
this. Replace MTD placeholders with real MTD nodes:
# flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
# flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>
Finally, reboot the device. The device should directly boot into
OpenWrt. Look for the characteristic power LED blinking pattern.
# reboot -f
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Boot into OpenWrt initramfs as for initial installation. To do that
without disassembly, you can write an initramfs image to the device
using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Concatenate the firmware backups, if you took them during installation using method 2:
$ cat ruckus_zf7025_fw1_backup.bin ruckus_zf7025_fw2_backup.bin > ruckus_zf7025_backup.bin
3. Write factory images downloaded from manufacturer website into
fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
before installation:
# mtd write ruckus_zf7025_backup.bin /dev/mtd1
4. Reboot the system, it should load into factory firmware again.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- The 2.4 GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Inspired by commit 9565c5726a, and by
facts that all Ubiquiti XM devices share flash layout, and images are
mostly compatible between all of them - enable uboot-envtools support for
whole XM line.
Build tested on: Ubiquiti Airrouter, Bullet-M (7240,7241), Nanobridge-M,
Nanostation-M (+ Loco), Picostation-M, Powerbridge-M, Rocket-M.
Runtime tested on: Ubiquiti Nanobridge M5 (XM).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
firmware
6. Update firmware using web interface with the OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+------------+
| use | address | example |
+-----+------------+------------+
| LAN | label | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g | label + 2 | *:74, *:d4 |
| 5g | label + 3 | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
enable additional crypto algorithms for hostap
hostap uses local implementations if not provided by crypto library,
so might as well enable in the crypto library for shared use by others.
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
Passing all arguments to /etc/init.d/$service restores the
behaviour of openwrt 21.02. This is relevant for services
such as etherwake which take more then one argument, e.g.:
"service etherwake start <list of devices to wake>"
Signed-off-by: Andrew Ammerlaan <andrewammerlaan@gentoo.org>
It's not just required for the PCI version, but for USB and presumably
SDIO as well.
Tested with 0e8d:7961 Comfast CF-953AX (MT7921AU).
Signed-off-by: Andre Heider <a.heider@gmail.com>
Realtek bluetooth devices need firmware. Add packages for some of
these.
Tested on a WNDR3700v4 with rtl8761bu firmware.
Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
USB adaptors with the RTL8761B chipset are cheap and readily available
but so far support is missing in Openwrt. Enable the relevant kernel
options and add a module to the kmod-bluetooth package. Increases size
of kmod-bluetooth ipk from 279140 bytes to 285320 bytes on my ath79 build.
Tested on a WNDR3700v4 with rtl8761bu firmware.
Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
This add --filter-A and --filter-AAAA options, to remove IPv4 or IPv6
addresses from DNS answers. these options is supported since version 2.87.
Co-authored-by: NueXini <nuexini@alumni.tongji.edu.cn>
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Changes:
712460c linux-firmware: Update firmware file for Intel Bluetooth 9462
90d5f7e linux-firmware: Update firmware file for Intel Bluetooth 9462
48954ba linux-firmware: Update firmware file for Intel Bluetooth 9560
0e205fd linux-firmware: Update firmware file for Intel Bluetooth 9560
06b941e linux-firmware: Update firmware file for Intel Bluetooth AX201
ba958ff linux-firmware: Update firmware file for Intel Bluetooth AX201
02bdea2 linux-firmware: Update firmware file for Intel Bluetooth AX211
7044d46 linux-firmware: Update firmware file for Intel Bluetooth AX211
1b99bcd linux-firmware: Update firmware file for Intel Bluetooth AX210
4668ae9 linux-firmware: Update firmware file for Intel Bluetooth AX200
5bdfdba linux-firmware: Update firmware file for Intel Bluetooth AX201
b0f995c amdgpu: update DMCUB firmware for DCN 3.1.6
d991031 rtl_bt: Update RTL8822C BT UART firmware to 0xFFB8_ABD6
fd62f01 rtl_bt: Update RTL8822C BT USB firmware to 0xFFB8_ABD3
b15fc21 WHENCE: mrvl: prestera: Add WHENCE entries for newly updated 4.1 FW images
bf5a337 mrvl: prestera: Update Marvell Prestera Switchdev FW to v4.1
4a733c2 iwlwifi: add new FWs from core74_pv-60 release
7d2bb50 qcom: drop split a530_zap firmware file
7d56713 qcom/vpu-1.0: drop split firmware in favour of the mbn file
1431496 qcom/venus-4.2: drop split firmware in favour of the mbn file
cf95783 qcom/venus-4.2: replace split firmware with the mbn file
1fe6f49 qcom/venus-1.8: replace split firmware with the mbn file
abc0302 linux-firmware: Add firmware for Cirrus CS35L41 on new ASUS Laptop
20d9516 iwlwifi: add new PNVM binaries from core74-44 release
06dbfbc iwlwifi: add new FWs from core69-81 release
05df8e6 qcom: update venus firmware files for VPU-2.0
cd6fcdb qcom: remove split SC7280 venus firmware images
1612706 qcom: update venus firmware file for v5.4
ad9fdba qcom: replace split SC7180 venus firmware images with symlink
dae5d46 rtw89: 8852b: update fw to v0.27.32.1
a8e86ec rtlwifi: update firmware for rtl8192eu to v35.7
9aa8db1 rtlwifi: Add firmware v4.0 for RTL8188FU
8f86b5a i915: Add HuC 7.10.3 for DG2
48407ff cnm: update chips&media wave521c firmware.
bd31846 brcm: add symlink for Pi Zero 2 W NVRAM file
771968c linux-firmware: Add firmware for Cirrus CS35L41 on ASUS Laptops
6f9620e linux-firmware: Add firmware for Cirrus CS35L41 on Lenovo Laptops
1d18cb9 linux-firmware: Add firmware for Cirrus CS35L41 on HP Laptops
e497757 rtw89: 8852b: add initial fw v0.27.32.0
98b5577 iwlwifi: add new FWs from core72-129 release
604026c iwlwifi: update 9000-family firmwares to core72-129
Signed-off-by: Nick Hainke <vincent@systemli.org>
dtim_period is a bss property, not a device one.
It is already handled properly in mac80211.sh
Fixes: 30c64825c7 ("hostapd: add dtim_period, local_pwr_constraint, spectrum_mgmt_required")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB: 1 x USB 3.0 port
Button: 1 x Reset button
Switch: 1 x Mode switch
LED: 1 x Blue LED + 1 x White LED
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
Get rid of drivers that are either limited to 802.11b/g or don't even support
cfg80211/mac80211. Most of these are either limited to boards that we don't even
support anymore because of firmware size, or were only used for custom hacks by
a really small number of users in the past.
Let's get rid of those to reduce the maintenance effort and the number of useless
packages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add kernel package 'mt7916-firmware' with firmware files for MT7916E devices.
These share the same driver as the MT7915 chipset, but use their own firmware.
Tested using a pair of AsiaRF AW7916-NPD cards.
Signed-off-by: Andrew Powers-Holmes <aholmes@omnom.net>
Add build option for nftables sets. By default disable iptables ipset
support. By default enable nftable nftset support since this is what
fw4 uses.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
dnsmasq: nftset: serve from ipset config
Use existing ipset configs as source for nftsets to be compatible with
existing configs. As the OS can either have iptables XOR nftables
support, it's fine to provide both to dnsmasq. dnsmasq will silently
fail for the present one. Depending on the dnsmasq compile time options,
the ipsets or nftsets option will not be added to the dnsmasq config
file.
dnsmasq will try to add the IP addresses to all sets, regardless of the
IP version defined for the set. Adding an IPv6 to an IPv4 set and vice
versa will silently fail.
Signed-off-by: Mathias Kresin <dev@kresin.me>
dnsmasq: support populating nftsets in addition to ipsets
Tell dnsmasq to populate nftsets instead of ipsets, if firewall4 is present in
the system. Keep the same configuration syntax in /etc/config/dhcp, for
compatibility purposes.
Huge thanks to Jo-Philipp Wich for basically writing the function.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
dnsmasq: obtain nftset ip family from nft
Unfortunately dnsmasq nft is noisy if an attempt to add a mismatched ip address
family to an nft set is made.
Heuristic to guess which ip family a nft set might belong by inferring
from the set name.
In order of preference:
If setname ends with standalone '4' or '6' use that, else
if setname has '4' or '6' delimited by '-' or '_' use that (eg
foo-4-bar) else
If setname begins with '4' or '6' standalone use that.
By standalone I mean not as part of a larger number eg. 24
If the above fails then use the existing nft set query mechanism and if
that fails, well you're stuffed!
With-thanks-to: Jo-Philipp Wich <jo@mein.io> who improved my regexp
knowledge.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
dnsmasq: specify firewall table for nftset
Permit ipsets to specify an nftables table for the set. New config
parameter is 'table'. If not specified the default of 'fw4' is used.
config ipset
list name 'BK_4,BK_6'
option table 'dscpclassify'
option table_family 'ip'
option family '4'
list domain 'ms-acdc.office.com'
list domain 'windowsupdate.com'
list domain 'update.microsoft.com'
list domain 'graph.microsoft.com'
list domain '1drv.ms'
list domain '1drv.com'
The table family can also be specified, usually 'ip' or 'ip6' else the
default 'inet' capable of both ipv4 & ipv6 is used.
If the table family is not specified then finally a family option is
available to specify either '4' or '6' for ipv4 or ipv6 respectively.
This is all in addition to the existing heuristic that will look in the
nftset name for an ip family clue, or in total desperation, query the
value from the nftset itself.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When running sysupgrade from an existing configuration, move existing
ipset definitions to a dedicated config section. Later on, it will allow
to serve ipset as well as nftable sets from the same configuration.
Signed-off-by: Mathias Kresin <dev@kresin.me>
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based
on Tenbay WR1800K. They have the same hardware circuits and u-boot.
SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile),
SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these
models run the same firmware.
Specifications:
SOC: MT7621 + MT7905 + MT7975
ROM: 128 MiB
RAM: 256 MiB
LED: status *3 R/G/B
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP Server: 192.168.1.254
TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken)
MAC Address:
use address source
label 30:xx:xx:xx:xx:62 wan
lan 30:xx:xx:xx:xx:65 factory.0x8004
wan 30:xx:xx:xx:xx:62 factory.0x8004 -3
wlan2g 30:xx:xx:xx:xx:64 factory.0x0004
wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit
TFTP Installation (initramfs image only & recommend):
1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
directory of the tftp server. (tftpd64 is a good choice for Windows)
3. Start the TFTP server, plug in the power supply, and wait for the
system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin", we need
it to back to stock firmware.
5. Use "fw_printenv" command to list envs.
If "firmware_select=2" is observed then set u-boot enviroment:
/# fw_setenv firmware_select 1
6. Apply sysupgrade.bin in OpenWrt LuCI.
Web UI Installation:
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs.
If "firmware_select=2" is observed then set u-boot enviroment:
/# fw_setenv firmware_select 1
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.
Recovery to stock firmware:
a. Upload "firmware.bin" to OpenWrt /tmp, then execute:
/# mtd -r write /tmp/firmware.bin firmware
b. We can also write factory image "UploadBrush-bin.img" to firmware
partition to recovery. Upload image file to /tmp, then execute:
/# mtd erase firmware
/# mtd -r write /tmp/UploadBrush-bin.img firmware
How to extract stock firmware image:
Download stock firmware, then use openssl:
openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \
-out "firmware.tar.tgz" -k QiLunSmartWL
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Do not use find_vpid(), but get_task_pid() to get the pid from
pThrCntrl->tid. This is now a ponter to struct task_struct instead of
an integer.
This fixes the build of ltq-tapi with lantiq/xway.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not include asm/irq.h directly, but include linux/interrupt.h instead.
This fixes the build of ltq-tapi with lantiq/xway.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports a commit which fixes a use after free bug in awk.
CVE-2022-30065 description:
A use-after-free in Busybox 1.35-x's awk applet leads to denial of
service and possibly code execution when processing a crafted awk
pattern in the copyvar function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports a commit from upstream dnsmasq to fix CVE-2022-0934.
CVE-2022-0934 description:
A single-byte, non-arbitrary write/use-after-free flaw was found in
dnsmasq. This flaw allows an attacker who sends a crafted packet
processed by dnsmasq, potentially causing a denial of service.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In a254279a6c LS1012A-IOT kernel image was switched to FIT.
But u-boot config is lack of FIT and ext4 support.
This patch enables it.
It also fix envs, because for some reason this board need to use "loadaddr"
variable in brackets.
Fixes: #9894
Fixes: a254279a6c ("layerscape: Change to combined rootfs on sd images")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
In my commit da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_*
modules") I missed a few default config options and description entries.
Those should be gone as well.
Fixes: da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_* modules")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Changes between 1.1.1r and 1.1.1s [1 Nov 2022]
*) Fixed a regression introduced in 1.1.1r version not refreshing the
certificate data to be signed before signing the certificate.
[Gibeom Gwon]
Changes between 1.1.1q and 1.1.1r [11 Oct 2022]
*) Fixed the linux-mips64 Configure target which was missing the
SIXTY_FOUR_BIT bn_ops flag. This was causing heap corruption on that
platform.
[Adam Joseph]
*) Fixed a strict aliasing problem in bn_nist. Clang-14 optimisation was
causing incorrect results in some cases as a result.
[Paul Dale]
*) Fixed SSL_pending() and SSL_has_pending() with DTLS which were failing to
report correct results in some cases
[Matt Caswell]
*) Fixed a regression introduced in 1.1.1o for re-signing certificates with
different key sizes
[Todd Short]
*) Added the loongarch64 target
[Shi Pujin]
*) Fixed a DRBG seed propagation thread safety issue
[Bernd Edlinger]
*) Fixed a memory leak in tls13_generate_secret
[Bernd Edlinger]
*) Fixed reported performance degradation on aarch64. Restored the
implementation prior to commit 2621751 ("aes/asm/aesv8-armx.pl: avoid
32-bit lane assignment in CTR mode") for 64bit targets only, since it is
reportedly 2-17% slower and the silicon errata only affects 32bit targets.
The new algorithm is still used for 32 bit targets.
[Bernd Edlinger]
*) Added a missing header for memcmp that caused compilation failure on some
platforms
[Gregor Jasny]
Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
Calling /etc/init.d/uhttpd reload directly in the acme hotplug script
can inadvertently start a stopped instance.
Signed-off-by: Glen Huang <i@glenhuang.com>
This is necessary with firewall4 to avoid a hard-to-diagnose race
condition during boot, causing DNAT rules not to be taken into account
correctly.
The root cause is that, during boot, the ruleset is mostly empty, and
interface-related rules (including DNAT rules) are added incrementally.
If a packet hits the input chain before the DNAT rules are setup, it can
create buggy conntrack entries that will persist indefinitely.
This new default should be safe because firewall4 explicitly accepts
authorized traffic and rejects the rest. Thus, in normal operations, the
default policy is not used.
Fixes: #10749
Ref: https://github.com/openwrt/openwrt/issues/10749
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
The sector number must be stored in hex. Otherwise, the number (like 16)
will be parsed as hex and any write to the partition will end up with an
error like:
MTD erase error on /dev/mtd5: Invalid argument
Fixes: 9adfeccd84 ("uboot-envtools: Add support for IPQ806x AP148 and DB149")
Fixes: 54b275c8ed ("ipq40xx: add target")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@fungible.com>
Add a package for drm_ttm_helper.ko. CONFIG_DRM_TTM_HELPER is compiled
into the kernel on armvirt/64, x86/64, x86/generic and x86/legacy
because also some DRM drivers are compiled into the kernel. On x86/geode
it is not compiled into the kernel, but kmod-drm-amdgpu and
kmod-drm-radeon depend on it.
This fixes the x86/geode build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For kernel versions before 5.2, the required IPsec modes have to be
enabled explicitly (they are built-in for newer kernels).
Commit 1556ed155a ("kernel: mode_beet mode_transport mode_tunnel xfram
modules") tried to handle this, but it does not really work.
Since we don't support these kernel versions anymore and the code is
also broken, let's remove it.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[Remove old generic config options too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
a92c0a7 dhcpv6-ia: make tmp lease file hidden
4a673e1 fix null pointer dereference for INFORM messages
860ca90 odhcpd: Support for Option NTP and SNTP
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The kernel module gpio-mcp23s08 has been replaced by the new
pinctrl-mcp23s08* kernel modules.
There are now 3 kernel modules for this device
- Common module for both I2C and SPI kmod-pinctrl-mcp23s08
- Module for I2C kmod-pinctrl-mcp23s08-i2c
- Module for SPI kmod-pinctrl-mcp23s08-spi
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Adding a new method to `ubus call dsl` to retrieve DSL statistics
used to feed the DSL charts (bit allocation, SNR, QLN and HLOG)
Signed-off-by: Roland Barenbrug <roland@treslong.com>
[fix pointer error, clean up]
Signed-off-by: Andre Heider <a.heider@gmail.com>
DSL_G997_LineStatusData_t defines special invalid values, skip these
metrics.
Signed-off-by: Roland Barenbrug <roland@treslong.com>
[split patch]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Add support for the Linksys EA4500 v3 wireless router
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Winbond W971GG6KB-25)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
QCA9580 3T3R 802.11 an
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1, same as ea4500 v2
USB: 1 single USB 2.0 host port
BUTTON: Reset - WPS
LED: 1x system-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label 94:10:3e:xx:xx:6f caldata@cal_macaddr
lan 94:10:3e:xx:xx:6f $label
wan 94:10:3e:xx:xx:6f $label
WiFi4_2G 94:10:3e:xx:xx:70 caldata@cal_ath9k_soc
WiFi4_5G 94:10:3e:xx:xx:71 caldata@cal_ath9k_pci
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.1.0/24
(e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
initramfs image as "openwrt.bin"
3. To test OpenWrt only, go to step 4 and never execute step 5;
To install, auto_recovery should be disabled first, and boot_part
should be set to 1 if its current value is not.
ath> setenv auto_recovery no
ath> setenv boot_part 1
ath> saveenv
4. Boot the initramfs image using U-Boot
ath> setenv serverip 192.168.1.66
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm
5. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Note: Like many other routers produced by Linksys, it has a dual
firmware flash layout, but because I do not know how to handle
it, I decide to disable it for more usable space. (That is why
the "auto_recovery" above should be disabled before installing
OpenWRT.) If someone is interested in generating factory
firmware image capable to flash from stock firmware, as well as
restoring the dual firmware layout, commented-out layout for the
original secondary partitions left in the device tree may be a
useful hint.
Installation from Web Interface
------------
1. Login to the router via its web interface (default password: admin)
2. Find the firmware update interface under "Connectivity/Basic"
3. Choose the OpenWrt factory image and click "Start"
4. If the router still boots into the stock firmware, it means that
the OpenWrt factory image has been installed to the secondary
partitions and failed to boot (since OpenWrt on EA4500 v3 does not
support dual boot yet), and the router switched back to the stock
firmware on the primary partitions. You have to install a stock
firmware (e.g. 3.1.6.172023, downloadable from
https://www.linksys.com/support-article?articleNum=148385 ) first
(to the secondary partitions) , and after that, install OpenWrt
factory image (to the primary partitions). After successful
installation of OpenWrt, auto_recovery will be automatically
disabled and router will only boot from the primary partitions.
Signed-off-by: Edward Chow <equu@openmail.cc>
Several Broadcom targets were using the nand_do_upgrade_success
shell function which has been removed by commit e25e6d8e54
("base-files: fix and clean up nand sysupgrade code"). Refactor the
new nand_do_upgrade to bring back nand_do_upgrade_success with the
behavior expected by those users.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
When firmware images only contained compressed kernels and squashfs roots,
uncompressed tar files were a good option. We are now using UBIFS images,
both raw and tarred, as well as ubinized (full UBI partition) images, all
of which benefit greatly from compression.
For example, a raw ubinized backup taken from a running Askey RT4230W REV6
(such full backups can be restored via the LUCI's sysupgrade UI) is over
400 MB, but compresses to less than 10 MB.
This commit adds support for gzipped versions of all file types already
accepted by the nand sysupgrade mechanism, be them raw or tarred.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
It has been reported that ubinized nand sysupgrade fails under certain
circumstances, being unable to detach the existing ubi partition due to
volumes within the partition being mounted.
This is an attempt to solve such issues by unmounting and removing
ubiblock devices and unmounting ubi volumes within the target partition
prior to detaching and formatting it.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
- Never return from 'nand_do_upgrade', not even in case of errors, as that
would cause execution of sysupgrade code not intended for NAND devices.
- Unify handling of sysupgrade success and failure.
- Detect and report more error conditions.
- Fix outdated/incorrect/unclear comments.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Commit e8b5429609 included an unintended change and we now call
scan_wifi before a network reload.
Restore the original behaviour and call scan_wifi only after a network
reload.
Fixes: e8b5429609 ("base-files: wifi: tidy up the reconf code")
Signed-off-by: Bob Cantor <bobc@confidesk.com>
Commit b82cc80713 included an unintended change and we now call
scan_wifi before a network reload.
Restore the original behaviour and call scan_wifi only after a network
reload.
Fixes: b82cc80713 ("base-files: wifi: swap the order of some ubus calls")
Signed-off-by: Bob Cantor <bobc@confidesk.com>
CONFIG_MAC80211_MESH isn't defined for this package, rendering the patch
useless. Match protecting the access of sta_info.mesh with the very same
define declaring it.
Fixes 45109f69a6 "mac80211: fix compile error when mesh is disabled"
Signed-off-by: Andre Heider <a.heider@gmail.com>
This updates mac80211 to version 5.15.74-1 which is based on kernel
5.15.74.
The removed patches were applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changes:
084911c Release libbsd 0.11.7
3538d38 man: Discourage using the library in non-overlay mode
03fccd1 include: Adjust reallocarray() per glibc adoption
6b6e686 include: Adjust arc4random() per glibc adoption
da1f45a include: explicit_bzero() requires _DEFAULT_SOURCE
2f9eddc include: Simplify glibc version dependent macro handling
28298ac doc: Switch references from pkg-config to pkgconf
ef981f9 doc: Add missing empty line to separate README sections
6928d78 doc: Refer to the main git repository as primary
d586575 test: Fix explicit_bzero() test on the Hurd
be327c6 fgetwln: Add comment about lack of getwline(3) for recommendation
a14612d setmode: Dot not use saveset after free
f4baceb man: Rewrite gerprogname(3bsd) from scratch
f35c545 man: Lowercase man page title
b466b14 man: Document that some arc4random(3) functions are now in glibc 2.36
1f6a48b Sync arc4random(3) implementation from OpenBSD
873639e Fix ELF support for big endian SH
c9c78fd man: Use -compact also for alternative functions in libbsd(7)
5f21307 getentropy: Fix function cast for getauxval()
Signed-off-by: Nick Hainke <vincent@systemli.org>
struct of_device_id is not implicitly included anymore. Include
<linux/mod_devicetable.h> to fix compilation on Linux 5.15.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
MODULE_SUPPORTED_DEVICE is gone after Linux 5.15. Drop it's usage on
newer kernels to fix compilation with Linux 5.15.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The result of copy_to_user() now has to be checked explicitly. Also
MODULE_SUPPORTED_DEVICE is gone after Linux 5.10.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
MODULE_SUPPORTED_DEVICE was removed after Linux 5.10. Drop it from the
driver as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
struct of_device_id is not implicitly included anymore. Include
<linux/mod_devicetable.h> to fix compilation on Linux 5.15.
Also upstream commit a24d22b225ce15 ("crypto: sha - split sha.h into
sha1.h and sha2.h") from Linux 5.11 moves functionality from sha.h to
sha1.h.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
set_fs is no longer supported since kernel 5.13 for mips.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Support was added as variant of 7530 (DEVICE_ALT0_*) in:
cb6f4be1 "ipq40xx: add support for FRITZ!Box 7520"
u-boot has a distinct config for it [0], built it.
[0] https://github.com/chunkeey/FritzBox-4040-UBOOT/pull/6
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.
Suggested-by: Steffen Pfendtner <s.pfendtner@ads-tec.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.
Suggested-by: Steffen Pfendtner <s.pfendtner@ads-tec.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.
Suggested-by: Steffen Pfendtner <s.pfendtner@ads-tec.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.
Suggested-by: Steffen Pfendtner <s.pfendtner@ads-tec.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The of_mmc_spi.o resource is provider agnostic in kernels greater 5.13
and does not depend anymore on CONFIG_OF [0].
[0] - edd6021465
Suggested-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Similar to the implementation for the BPi-R3 use the same logic also
for determining the device to look for the U-Boot environment of the
BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This new NTFS driver was added in kernel 5.15. Avoid building empty
package for kernel 5.10.
Fixes: bd0db6017b ("kernel: 5.15: add new module")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix accessing the environment in case no OS is installed on the flash
media selected for boot as this is possible when booting initramfs.
In case of relying on the device specified to be mounted as rootfs to
be present, rather just use the kernel cmdline 'root' variable as a
hint to decide where to read/write the U-Boot environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ee54c6b libfstools: skip JFFS2 padding on block devices
Fixes config restore on the BPi R3 when using MMC storage.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove patches adding support for MT7621 which have been merged upsteam.
Patches for MT7981 and MT7986 have been merged too, but not in time to
be included in the 2022.10 release, so we have to keep carrying them
until the 2023.01 release.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make it possible to setup default WAN interface for devices with built-in LTE
modems, using QMI or MBIM.
Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Replace the extern inline with a static inline. With extern inline the
compiler will generate the function in all compile units including this
file which breaks linking later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Provide ATF support for Methode eDPU as well, this makes it easy for
OpenWrt users to update the included U-boot+ATF combo.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add support for building for Methode eDPU board, no patches are needed
as board has been upstreamed and is part of the 2022.10-rc releases.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Update mvebu U-boot to 2022.10 to avoid backporting patches in order
to support Methode eDPU.
It also allows dropping existing patches as they are all backports.
Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs
Tested-by: Russell Morris <github@rkmorris.us> # espressobin-v3-v5-1gb-1cs
Tested-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [Turris Omnia]
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
4fbf6d7 ruleset.uc: log forwarded traffic not matched by zone policies
c7201a3 main.uc: reintroduce set reload restriction
756f1e2 ruleset: fix emitting set_mark/set_xmark rules with masks
3db4741 ruleset: properly handle zone names starting with a digit
43d8ef5 fw4: fix formatting of default log prefix
592ba45 main.uc: remove uneeded/wrong set reload restrictions
b0a6bff tests: fix testcases
145e159 fw4: recognize `option log` and `option counter` in `config nat` sections
ce050a8 fw4: fall back to device if l3_device is not available in ifstatus
Fixes: #10639, #10965
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
On machines with a coarse monotonic clock (here: TP-Link RE200 powered
by a MediaTek MT7620A) it can happen that the two DNS requests (for A
and AAAA) share the same transaction ID. If this happens the second
reply is wrongly dropped and nslookup reports "No answer".
Fix this by ensuring that the transaction IDs are unique.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
This makes it clear, which phy a wlan device belongs to and also helps with
telling them apart by including the mode in the ifname.
Preparation for automatically renaming PHYs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These will be used to give WLAN PHYs a specific name based on path specified
in board.json. The platform board.d script can assign a specific order based
on available slots (PCIe slots, WMAC device) and device tree configuration.
This helps with maintaining config compatibility in case the device path
changes due to kernel upgrades.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Fixes: 590eaaeed5 ("mac80211: fix issues in HE capabilities")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add the measurement report value to the beacon reports send via ubus. It
is possible to derive from the measurement report if a station refused to
do a beacon report and why. It is important to know why a station refuses
to do a beacon-report. In particular, we should not request a beacon
report from a station again that refused a beacon-report before.
The rejection reasons can be found by looking at the bits defined by:
- MEASUREMENT_REPORT_MODE_ACCEPT
- MEASUREMENT_REPORT_MODE_REJECT_LATE
- MEASUREMENT_REPORT_MODE_REJECT_INCAPABLE
- MEASUREMENT_REPORT_MODE_REJECT_REFUSED
Suggested-by: Ian Clowes <clowes_ian@hotmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
This mainly affects scanning and beacon parsing, especially with MBSSID enabled
Fixes: CVE-2022-41674
Fixes: CVE-2022-42719
Fixes: CVE-2022-42720
Fixes: CVE-2022-42721
Fixes: CVE-2022-42722
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable HE SU beamformee by default
Fix spatial reuse configuration:
- he_spr_sr_control is not a bool for enabling, it contains multiple bits
which disable features that should be disabled by default
- one of the features (PSR) can be enabled through he_spr_psr_enabled
- add option to disable bss color / spatial reuse
Signed-off-by: Felix Fietkau <nbd@nbd.name>
CONFIG_CMD_MTDPART does not exist, fix it.
Fixes: e9ad412 ("uboot-mediatek: add build for Ubiquiti Networks UniFi 6 LR")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
CONFIG_CMD_MTDPART does not exist, fix it.
Fixes: ed50004 ("uboot-mediatek: add support for Linksys E8450")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
dhcpv6.script contained support for disabling prefix delegation of 464XLAT
sub-interface, but netifd protocol handler was missing the required
export to disable this. Add missing export, akin to DS-Lite and MAP.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
This fixes following compile error seen when
building mac80211 with mesh disabled:
.../backports-5.15.58-1/net/mac80211/agg-rx.c: In function 'ieee80211_send_addba_resp':
...backports-5.15.58-1/net/mac80211/agg-rx.c:255:17: error: 'struct sta_info' has no member named 'mesh'
255 | if (!sta->mesh)
| ^~
sta_info.h shows this item as being optional based on flags:
struct mesh_sta *mesh;
Guard the check to fix this.
Fixes: f96744ba6b ("mac80211: mask nested A-MSDU support for mesh")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
As wolfSSL is having hard time maintaining ABI compatibility between
releases, we need to manually force rebuild of packages depending on
libwolfssl and thus force their upgrade. Otherwise due to the ABI
handling we would endup with possibly two libwolfssl libraries in the
system, including the patched libwolfssl-5.5.1, but still have
vulnerable services running using the vulnerable libwolfssl-5.4.0.
So in order to propagate update of libwolfssl to latest stable release
done in commit ec8fb542ec ("wolfssl: fix TLSv1.3 RCE in uhttpd by
using 5.5.1-stable (CVE-2022-39173)") which fixes several remotely
exploitable vulnerabilities, we need to bump PKG_RELEASE of all
packages using wolfSSL library.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
mac80211 incorrectly processes A-MSDUs contained in A-MPDU frames. This
results in dropped packets and severely impacted throughput.
As a workaround, don't indicate support for A-MSDUs contained in
A-MPDUs. This improves throughput over mesh links by factor 10.
Ref: https://github.com/openwrt/mt76/issues/450
Signed-off-by: David Bauer <mail@david-bauer.net>
If you would like to compile the newest version of U-boot together with the stable
OpenWrt version, which does not have LibreSSL >= 3.5, which was updated
in the master branch by commit 5451b03b7c
("tools/libressl: bump to v3.5.3"), then you need these two patches to
fix it. They are backported from U-boot repository.
This should be backported to stable OpenWrt versions.
Reported-by: Michal Vasilek <michal.vasilek@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This issue was reported by @paper42, who is using Void Linux with musl
to compile OpenWrt and its packages and found out it is not possible to
compile U-boot for Turris Omnia (neither any other).
It fixes following output:
```
HOSTCC tools/kwboot
tools/kwboot.c: In function 'kwboot_tty_change_baudrate':
tools/kwboot.c:662:6: error: 'struct termios' has no member named 'c_ospeed'
662 | tio.c_ospeed = tio.c_ispeed = baudrate;
| ^
tools/kwboot.c:662:21: error: 'struct termios' has no member named 'c_ispeed'
662 | tio.c_ospeed = tio.c_ispeed = baudrate;
| ^
tools/kwboot.c:690:31: error: 'struct termios' has no member named 'c_ospeed'
690 | if (!_is_within_tolerance(tio.c_ospeed, baudrate, 3))
| ^
tools/kwboot.c:693:31: error: 'struct termios' has no member named 'c_ispeed'
693 | if (!_is_within_tolerance(tio.c_ispeed, baudrate, 3))
|
```
Tested-by: Michal Vasilek <michal.vasilek@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Remove upstremed patch:
- 100-tracecmd-add-NO_LIBZSTD-option-to-disable-libzstd.patch
Changes:
c65c02c trace-cmd: Version 3.1.3
14a7aca trace-cmd library: Add API for mapping between host and guests
9191b8e tracecmd extract: Allow using --compression.
d63ae35 trace-cmd report: Add callback for kvm plugin to show guest functions
0c7ef72 trace-cmd library: Add man pages for iterator functions
3cd1b55 trace-cmd library: Add tracecmd_follow_event()
27ea9e1 libtracecmd: Add documentation on tracecmd_set/get_private()
3c544ad libtracecmd: Add a man pages for handling of time stamps
5baf7a3 libtracecmd: Add check-manpages.sh
ee007a1 trace-cmd library: Make tracecmd_filter_match() local
cb04105 tracecmd library documentation: Use star and not underscore for function names
54931be trace-cmd: Do not return zero length name for guest by name
43ffa27 trace-cmd: Close socket descriptor on failed connection
4744ca3 trace-cmd record/agent: Add --notimeout option
e512b22 trace-cmd: Add compile time overrides for libraries
a6fe935 trace-cmd: README: Add note on installing libtracecmd
067f45f trace-cmd: libtracecmd: Fixing linking to C++ code
689a0d4 tracecmd: Add NO_LIBZSTD option to disable libzstd
6bbcd3e trace-cmd report: Use library tracecmd_filter_*() logic
955d05f trace-cmd report: Make filter arguments match their files
82ed4a9 trace-cmd library: Add filtering logic for iterating events
dbd8777 trace-cmd report: Use tracecmd_iterate_events_multi()
78a74b1 trace-cmd library: Allow callers to save private data in tracecmd_input handlers
b37903a tracecmd library: Add tracecmd_iterate_events_multi()
d83b662 tracecmd utest: Add test to test using the libraries to read
2cb6cc2 tracecmd library: Add tracecmd_iterate_events()
762839a tracecmd: Use make variable instead of if statement for zlib test
1504f3f trace-cmd: Document new proxy args for {agent,record}
9a1c5d7 trace-cmd record: Keep --proxy from being passed to agents
ef8a8d7 trace-cmd libs: Initialize msg to NULL tracecmd_msg_read_data()
39ec10a trace-cmd: Do not use instance from trace context
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
93f4d52 libtracefs: version 1.5
bc857db libtracefs: Add tracefs_u{ret}probe_alloc to generic man page
db55441 libtracefs: Add tracefs_debug_dir() to generic libtracefs man page
d2d5924 libtracefs: Add test instructions for openSUSE
4a7b475 libtracefs: Fix test suite typo
ee8c644 libtracefs: Add tracefs_tracer_available() helper
799d88e libtracefs: Add API to set custom tracing directory
1bb00d1 libtracefs: allow pthread inclusion overrideable in Makefile
04651d0 libtracefs sqlhist: Allow pointers to match longs
9de59a0 libtracefs: Remove double free attempt of new_event in tracefs_synth_echo_cmd()
0aaa86a libtracefs: Fix use after free in tracefs_synth_alloc()
d2d5340 libtracefs: Add missed_events to record
9aaa8b0 libtracefs: Set the number of CPUs in tracefs_local_events_system()
56a0ba0 libtracefs: Return negative number when tracefs_filter_string_append() fails
c5f849f libtracefs: Set the long size of the tep handle in tracefs_local_events_system()
5c8103e revert: 0de961e74f96 ("libtracefs: Set visibility of parser symbols as 'internal'")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
fda4ad9 libtraceevent: version 1.6.3
d02a61e libtraceevent: Add man pages for tep_plugin_kvm_get/put_func()
6643bf9 libtraceevent: Have kvm_exit/enter be able to show guest function
a596299 libtraceevent: Add tep_print_field() to check-manpages.sh deprecated
065c9cd libtraceevent: Add man page documentation of tep_get_sub_buffer_size()
6e18ecc libtraceevent: Add man page for tep_plugin_add_option()
6738713 libtraceevent: Add some missing functions to generic libtraceevent man page
deefe29 libtraceevent: Include meta data functions in libtraceevent man pages
cf6dd2d libtraceevent: Add tep_get_function_count() to libtraceevent man page
5bfc11e libtraceevent: Add printk documentation to libtraceevent man page
65c767b libtraceevent: Update man page to reflect tep_is_pid_registered() rename
7cd173f libtraceevent: Add check-manpages.sh
fd6efc9 libtraceevent: Documentation: Correct typo in example
5c375b0 libtraceevent: Fixing linking to C++ code
7839fc2 libtraceevent: Makefile - set LIBS as conditional assignment
c5493e7 libtraceevent: Remove double assignment of val in eval_num_arg()
efd3289 libtraceevent: Add warnings if fields are outside the event
Signed-off-by: Nick Hainke <vincent@systemli.org>
4f96e67 Up the release version to 2.66
60ff008 Fix typos in the cap_from_text.3 man page.
281b6e4 Add captrace to .gitignore file
09a2c1d Add an example of using BPF kprobing to trace capability use.
26e3a09 Clean up getpcaps code.
fc804ac getpcaps: catch PID parsing errors.
fc437fd Fix an issue with bash displaying an error.
7db9589 Some more simplifications for building
27e801b Fix for "make clean ; make -j48 test"
Signed-off-by: Nick Hainke <vincent@systemli.org>
As also ramips/mt7621 now has a user of the ubnt-ledbar driver, make
the package available on all targets by removing the dependency on
@TARGET_mediatek_mt7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes denial of service attack and buffer overflow against TLS 1.3
servers using session ticket resumption. When built with
--enable-session-ticket and making use of TLS 1.3 server code in
wolfSSL, there is the possibility of a malicious client to craft a
malformed second ClientHello packet that causes the server to crash.
This issue is limited to when using both --enable-session-ticket and TLS
1.3 on the server side. Users with TLS 1.3 servers, and having
--enable-session-ticket, should update to the latest version of wolfSSL.
Thanks to Max at Trail of Bits for the report and "LORIA, INRIA, France"
for research on tlspuffin.
Complete release notes https://github.com/wolfSSL/wolfssl/releases/tag/v5.5.1-stable
Fixes: CVE-2022-39173
Fixes: https://github.com/openwrt/luci/issues/5962
References: https://github.com/wolfSSL/wolfssl/issues/5629
Tested-by: Kien Truong <duckientruong@gmail.com>
Reported-by: Kien Truong <duckientruong@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit a596a8396b as I've
just discovered private email, that the issue has CVE-2022-39173
assigned so I'm going to reword the commit and push it again.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes denial of service attack and buffer overflow against TLS 1.3
servers using session ticket resumption. When built with
--enable-session-ticket and making use of TLS 1.3 server code in
wolfSSL, there is the possibility of a malicious client to craft a
malformed second ClientHello packet that causes the server to crash.
This issue is limited to when using both --enable-session-ticket and TLS
1.3 on the server side. Users with TLS 1.3 servers, and having
--enable-session-ticket, should update to the latest version of wolfSSL.
Thanks to Max at Trail of Bits for the report and "LORIA, INRIA, France"
for research on tlspuffin.
Complete release notes https://github.com/wolfSSL/wolfssl/releases/tag/v5.5.1-stable
Fixes: https://github.com/openwrt/luci/issues/5962
References: https://github.com/wolfSSL/wolfssl/issues/5629
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This will prevent `module is already loaded` lines from
appearing in the logs when a PPP connection is reconnecting
Signed-off-by: Manas Sambhus <manas.sambhus+github@gmail.com>
'rule inet dscpclassify dscp_match meta l4proto { udp } th dport { 3478 }
th sport { 3478-3497, 16384-16387 } goto ct_set_ef' works with
'nft add', but not 'nft insert', the latter yields:
"BUG: unhandled op 4".
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The luci ucode rewrite exposed the definition of START as being over 1K
from start of file. Initial versions limited the search for START &
STOP to within the 1st 1K of a file. Whilst the search has been
expanded, it doesn't do any harm to define START early in the file like
all other init scripts seen so far.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This reverts commit 6e9613844c.
The patch was wrong in the first place as we base everything on
backports package and the compilation error was caused by an ath11k
present downstream. (will be needed later when backports package will be
updated but not now)
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With kernel 5.15.61 the define IEEE80211_MAX_AMPDU_BUF got changed to
IEEE80211_MAX_AMPDU_BUF_HE. Add patch to fix compilation error on next
5.15 kernel versions.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rename libwolfssl-cpu-crypto to libwolfsslcpu-crypto so that the
regular libwolfssl version comes first when running:
opkg install libwolfssl
Normally, if the package name matches the opkg parameter, that package
is preferred. However, for libraries, the ABI version string is
appended to the package official name, and the short name won't match.
Failing a name match, the candidate packages are sorted in alphabetical
order, and a dash will come before any number. So in order to prefer
the original library, the dash should be removed from the alternative
library.
Fixes: c3e7d86d2b (wolfssl: add libwolfssl-cpu-crypto package)
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Move CONFIG_PACKAGE_libwolfssl-benchmark from the top of
PKG_CONFIG_DEPENDS to after PKG_ABI_VERSION is set.
This avoids changing the ABI version hash whether the bnechmark package
package is selected or not.
Fixes: 05df135cac (wolfssl: Rebuild when libwolfssl-benchmark gets changes)
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.
Specification:
- SoC : Qualcomm IPQ4019
- RAM : DDR3 512 MiB (H5TC4G63EFR)
- Flash : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet : 10/100/1000 Mbps x2
- Transceiver : Qualcomm QCA8072
- WWAN : Telit LN940A9
- Z-Wave : Silicon Labs ZM5101
- Bluetooth : Qualcomm CSR8811
- Audio DAC : Realtek ALC5629
- Audio Amp. : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
- RGB LED, Fan, Temp. sensors
- Touch Sensor : Cypress CY8C4014LQI
- RGB LED driver : TI LP55231 (2x)
- LEDs/Keys : 11x, 6x
- UART : through-hole on PCB
- J1: 3.3V, TX, RX, GND from tri-angle marking
- 115200n8
- Power : 12 VDC, 2.5 A
Flash instruction using initramfs image:
1. Prepare TFTP server with the IP address 192.168.132.100 and place the
initramfs image to TFTP directory with the name "C0A88401.img"
2. Boot NCP-HG100/Cellular and interrupt after the message
"Hit any key to stop autoboot: 2"
3. Perform the following commands and set bootcmd to allow booting from
eMMC
setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
saveenv
4. Perform the following command to load/boot the OpenWrt initramfs image
tftpboot && bootm
5. On the initramfs image, perform sysupgrade with the sysupgrade image
(if needed, backup eMMC partitions by dd command and download to
other place before performing sysupgrade)
6. Wait for ~120 seconds to complete flashing
Known issues:
- There are no drivers for audio-related chips/functions in Linux Kernel
and OpenWrt, they cannot be used.
- There is no driver for MINI54FDE Micro-Controller Unit, customized for
this device by the firmware in the MCU. This chip controls the
following functions, but they cannot be controlled in OpenWrt.
- RGB LED
- Fan
this fan is controlled automatically by MCU by default, without
driver
- Thermal Sensors (2x)
- Currently, there is no driver or tool for CY8C4014LQI and cannot be
controlled. It cannot be exited from "booting mode" and moved to "normal
op mode" after booting. And also, the 4x buttons (mic mute, vol down,
vol up, alexa trigger) connected to the IC cannot be controlled.
- it can be exited from "booting mode" by installing and executing
i2cset command:
opkg update
opkg install i2c-tools
i2cset -y 1 0x14 0xf 1
- There is a connection issue on the control by uqmi for the WWAN module.
But modemmanager can be used without any issues and the use of it is
recommended.
- With the F2FS format, too many errors are reported on erasing eMMC
partition "rootfs_data" while booting:
[ 1.360270] sdhci: Secure Digital Host Controller Interface driver
[ 1.363636] sdhci: Copyright(c) Pierre Ossman
[ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
...
[ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 1.528325] mmc0: new HS200 MMC card at address 0001
[ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
[ 1.550323] Alternate GPT is invalid, using primary GPT.
[ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
...
[ 8.841400] mount_root: loading kmods from internal overlay
[ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.240465] block: attempting to load /etc/config/fstab
[ 9.246722] block: unable to load configuration (fstab: Entry not found)
[ 9.246863] block: no usable configuration
[ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
[ 9.438915] urandom_read: 5 callbacks suppressed
[ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
[ 12.243332] mmc_erase: erase error -110, status 0x800
[ 12.246638] mmc0: cache flush error -110
[ 15.134585] mmc_erase: erase error -110, status 0x800
[ 15.135891] mmc_erase: group start error -110, status 0x0
[ 15.139850] mmc_erase: group start error -110, status 0x0
...(too many the same errors)...
[ 17.350811] mmc_erase: group start error -110, status 0x0
[ 17.356197] mmc_erase: group start error -110, status 0x0
[ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
[ 17.446910] mmc0: tuning execution failed: -5
[ 17.447111] mmc0: cache flush error -110
[ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
[ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
[ 18.198691] block: attempting to load /etc/config/fstab
[ 18.198972] block: unable to load configuration (fstab: Entry not found)
[ 18.203029] block: no usable configuration
[ 18.211371] mount_root: overlay filesystem has not been fully initialized yet
[ 18.214487] mount_root: switching to f2fs overlay
So, this support uses ext4 format instead which has no errors.
Note:
- The primary uart is shared for debug console and Z-Wave chip. The
function is switched by GPIO15 (Linux: 427).
value:
1: debug console
0: Z-Wave
- NCP-HG100/Cellular has 2x os-image pairs in eMMC.
- 0:HLOS, rootfs
- 0:HLOS_1, rootfs_1
In OpenWrt, the first image pair is used.
- "bootipq" command in U-Boot requires authentication with signed-image
by default. To boot unsigned image of OpenWrt, use "mmc read" and
"bootm" command instead.
- This support is for "Cellular" variant of NCP-HG100 and not tested on
"WLAN" (non-cellular) variant.
- The board files of ipq-wifi may also be used in "WLAN" variant of
NCP-HG100, but unconfirmed and add files as for "Cellular" variant.
- "NET" LED is used to indicate WWAN status in stock firmware.
- There is no MAC address information in the label on the case, use the
address included in UUID in the label as "label-MAC" instead.
- The "CLOUD" LEDs are partially used for indication of system status in
stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
connected to the MCU.
MAC addresses:
LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex))
WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))
partition layout in eMMC (by fdisk, GPT):
Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910
Number Start (sector) End (sector) Size Name
1 34 1057 512K 0:SBL1
2 1058 2081 512K 0:BOOTCONFIG
3 2082 3105 512K 0:QSEE
4 3106 4129 512K 0:QSEE_1
5 4130 4641 256K 0:CDT
6 4642 5153 256K 0:CDT_1
7 5154 6177 512K 0:BOOTCONFIG1
8 6178 6689 256K 0:APPSBLENV
9 6690 8737 1024K 0:APPSBL
10 8738 10785 1024K 0:APPSBL_1
11 10786 11297 256K 0:ART
12 11298 11809 256K 0:HSEE
13 11810 28193 8192K 0:HLOS
14 28194 44577 8192K 0:HLOS_1
15 44578 306721 128M rootfs
16 306722 568865 128M rootfs_1
17 568866 3958065 1654M rootfs_data
[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The "tx_burst" option which should control the value was
expecting more of a list and hence tx_queue_data2_burst
value wasn't updated.
Yes, it would make sense to have a list for this, the
existing code only updates tx_queue_data2_burst and
not the other tx_queue_data[0134]_burst values.
Signed-off-by: Alberto Martinez-Alvarez <amteza@gmail.com>
(formatted commit message, wrote extra information into commit,
moved tx_burst to existing json_get_vars)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Prevents build errors by ensuring that it is only selected when a wext based
driver that needs it is also selected
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_RELEASE
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_VERSION
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_VERSION
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_SOURCE_DATE
to better organize the downloads.
Define PKG_VERSION here
using PKG_SOURCE_DATE.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The currently used shell expansion doesn't seem to exist [0] and also
does not work. This surely was not intended, so lets allow default
naming to actually work.
[0]: https://pubs.opengroup.org/onlinepubs/9699919799/utilities/V3_chap02.html
Fixes: be09c5a3cd ("base-files: add board.d support for bridge device")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
46f04f3808e8 devices: add MediaTek MT7986 WiSoC
b3e08c8b5a8f ops: make support for wireless extensions optional
1f695d9c7f82 nl80211: allow phy names that don't start with 'phy'
b7f9f06e1594 nl80211: fix phy/netdev index lookup
4a43b0d40ba5 nl80211: look up the phy name instead of assuming name == phy<idx>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Also include the station auth_type in the ubus and log message in order
to detect, if clients used FT or FILS to associate
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All contents of staging_dir/image are included in Image Builder (IB) in
case some binary needs to be included in final image. But in case of
this package, all sources are stored there and those clutter the final
tarball of IB for no reason. Those sources are not used during image
creation and are just dead weight. To put it in perspective, the IB for
21.02.0 is 158 MiB, 22.03.0-rc6 is 366 MiB and snapshot is over 620 MiB!
To fix it, put them in package build directory, so they won't end up
included in IB tarball.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
b704dc72e tests: sigma_dut and updated ConfResult value for Configurator failures
89de431f2 DPP: Add config response status value to DPP-CONF-SENT
10104915a tests: sigma_dut and DPP PB session overlap
80d5e264c Enhance QCA vendor roam event to indicate MLO links after reassociation
662249306 Update copyright notices for the QCA vendor definitions
8adcdd659 tests: Temporary workaround for dpp_chirp_ap_5g
ddcd15c2d tests: Fix fuzzing/sae build
7fa67861a tests: Fix p2p_channel_avoid3
ee3567d65 tests: Add more time for scan/connection
1d08b238c nl80211: Allow more time for the initial scan with 6 GHz
ac9e6a2ab tests: Allow 6 GHz opclasses in MBO checks
faf9c04cb Remove a host of unnecessary OPENSSL_IS_BORINGSSL ifdefs
b9cd5a82f Always process pending QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH data
ef4cd8e33 QoS: Use common classifier_mask for ipv4/ipv6
93be02592 Add fixed FDD mode to qca_btc_chain_mode QCA vendor attribute
e7cbfa1c1 tests: sigma_dut and DPP Enrollee unsupported curves
5565fbee2 DPP: Check Enrollee supported curves when building Config Response
ceae05cec tests: sigma_dut and DPP MUDURL setting for hostapd
4cfb484e9 DPP: Allow dpp_controller_start without arguments in CLIs
c97000933 Fix ifdef condition for imsi_privacy_cert
2a9a61d6c tests: SAE with extended key AKM
e35f6ed1d tests: More detailed report on SAE PMKSA caching error case
f70db167a SAE: Derive a variable length PMK with the new AKM suites
91010e6f6 SAE: Indicate AKM suite selector in commit for new AKM suites
e81ec0962 SAE: Use H2E unconditionally with the new AKM suites
f8eed2e8b SAE: Store PMK length and AKM in SAE data
9dc4e9d13 SAE: EAPOL-Key and key/MIC length information for the new AKM suites
a32ef3cfb SAE: Driver capability flags for the new SAE AKM suites
91df8c9c6 SAE: Internal WPA_KEY_MGMT_* defines for extended key AKMs
5c8a714b1 SAE: Use wpa_key_mgmt_sae() helper
5456b0f26 Define new RSN AKM suite selector values
def33101c DPP: Clear push button announcement state on wpa_supplicant FLUSH
35587fa8f tests: DPP Controller/Relay with need to discover Controller
d22dfe918 DPP: Event message for indicating when Relay would need a Controller
ca7892e98 tests: DPP Relay and adding/removing connection to a Controller
bfe3cfc38 DPP: Allow Relay connections to Controllers to be added and removed
808834b18 Add a comparison function for hostapd_ip_addr
f7763880b DPP: Advertise Configurator connectivity on Relay automatically
ff7cc1d49 tests: DPP Relay and dynamic Controller addition
ca682f80a DPP: Dynamic Controller initiated connection on Relay
d2388bcca DPP: Strict validation of PKEX peer bootstrapping key during auth
a7b8cef8b DPP3: Fix push button boostrapping key passing through PKEX
69d7c8e6b DPP: Add peer=id entry for PKEX-over-TCP case
b607d2723 tests: sigma_dut and DPP PB Configurator in wpa_supplicant
1ff9251a8 DPP3: Push button Configurator in wpa_supplicant
b94e46bc7 tests: PB Configurator in wpa_supplicant
ca4e82cbf tests: sigma_dut DPP/PKEX initiator as Configurator over TCP and Wi-Fi
e9137950f DPP: Recognize own PKEX Exchange Request if it ends up being received
692956446 DPP: Note PKEX code/identifier deletion in debug log
dfa9183b1 tests: DPP reconfig after Controller-initiated operation through Relay
ae4a3a6f6 DPP: Add DPP-CONF-REQ-RX event for Controller
17216b524 tests: sigma_dut DPP/PKEX initiator as Configurator (TCP) through Relay
fb2937b85 DPP: Allow Controller to initiate PKEX through Relay
15af83cf1 DPP: Delete PKEX code and identifier on success completion of PKEX
d86ed5b72 tests: Allow DPP_PKEX_REMOVE success in dpp_pkex_hostapd_errors
0a4f391b1 tests: sigma_dut and DPP Connector Privacy
479e412a6 DPP3: Default value for dpp_connector_privacy
7d12871ba test: DPP Private Peer Introduction protocol
148de3e0d DPP3: Private Peer Introduction protocol
786ea402b HPKE base mode with single-shot API
f0273bc81 OpenSSL: Remove a forgotten debug print
f2bb0839f test: DPP 3rd party config information
68209ddbe DPP: Allow 3rd party information to be added into config object
0e2217c95 DPP: Allow 3rd party information to be added into config request obj
3d82fbe05 Add QCA vendor subcommand and attributes for SCS rule configuration
16b62ddfa QCA vendor attribute for DBAM configuration
004b1ff47 tests: DPP Controller initiating through Relay
451ede2c3 DPP: Allow AP/Relay to be configured to listed for new TCP connections
248654d36 tests: sigma_dut DPP PB test cases
697b7d7ec tests: DPP push button
7bbe85987 DPP3: Allow external configuration to be specified on AP for PB
8db786a43 DPP3: Testing functionality for push button announcements
37bccfcab DPP3: Push button bootstrap mechanism
a0054fe7c Add AP and STA specific P802.11az security capabilities (vendor command)
159e63613 QCA vendor command for CoAP offload processing
3b7bb17f6 Add QCA vendor attribute for TIM beacon statistics
09a281e52 Add QCA vendor interface for PASN offload to userspace
809fb96fa Add a vendor attribute to configure concurrency policy for AP interface
a5754f531 Rename QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY
085a3fc76 EHT: Add 320 channel width support
bafe35df0 Move CHANWIDTH_* definitions from ieee80211_defs.h to defs.h
92f549901 tests: Remove the 80+80 vs. 160 part from wpa2_ocv_ap_vht160_mismatch
c580c2aec tests: Make OCV negative test error cases more robust
3c2ba98ad Add QCA vendor event to indicate driver recovery after internal failures
6b461f68c Set current_ssid before changing state to ASSOCIATING
8dd826741 QCA vendor attribute to configure direct data path for audio traffic
504be2f9d QCA vendor command support to get WLAN radio combinations
d5905dbc8 OCV: Check the Frequency Segment 1 Channel Number only on 80+80 MHz
Signed-off-by: David Bauer <mail@david-bauer.net>
Don't select channels designated for exclusive-indoor use when the
country3 element is set on outdoor operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
The 'fxload' tool contained in the examples provided with libusb is
actually useful and turns out to be the only way to load firmware into
some rather ancient EZ-USB microcontrollers made by Cypress (formerly
Anchor Chips).
The original 'fxload' tool from hotplug-linux has been abandonned long
ago and requires usbfs to be mounted in /proc/bus/usb/ (like it was in
Linux 2.4...).
Hence the best option is to package the modern 'fxload' from the libusb
examples which (unsurprisingly) uses libusb and works on modern
systems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
e065a7627a46 pex: update last query sent timestamp
6c888f897862 unet-cli: add stun server list editing support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
21360a1b1ce6 cli: fix typo
abfebece0af1 wg-linux: ship a copy of linux/wireguard.h
1cbb1a543cb3 pex: reduce unnecessary ping traffic
0c2f39e52d5d pex: remove pex event debug spam
dcf1362c2104 pex: add support for sending/receiving global PEX messages via unix socket
df5f70b8858c ubus: notify on network updates
e58a56697131 add DHT discovery service
be175767bc67 pex: keep active pex hosts after the specified timeout
543e4a3d2ed7 pex: move rx header check to callback function
395659b9c415 pex: move raw ip send code to sendto_rawudp() in utils.c
dda15ea8b3b2 pex: add utility function to get the sockets based on type / address family
e88f2cd4d3f0 utils: add support for passings address family to network_get_endpoint()
639cdcdf6eda pex: add support for figuring out the external data port via STUN servers
9144339ebe1f pex: improve handling of a longer list of PEX hosts
38212218ecdd unet-cli: add DHT support
0d37ca75434d pex: automatically create host entries from incoming endpoint port notifications
035fcc56ef60 host: keep multiple endpoint candidates, one for each type
a089e8ae7504 pex: avoid sending a query to a host more than once every 15 seconds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
libwolfssl-cpu-crypto is a variant of libwolfssl with support for
cryptographic CPU instructions on x86_64 and aarch64.
On aarch64, wolfSSL does not perform run-time detection, so the library
will crash when the AES functions are called. A preinst script attempts
to check for support by querying /proc/cpuinfo, if installed in a
running system. When building an image, the script will check the
DISTRIB_TARGET value in /etc/openwrt_release, and will abort
installation if target is bcm27xx.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
cc4eb79 ubus: support obtaining numeric error code
01c412c ubus: add toplevel constants for ubus status codes
8e240fa ubus: allow object method call handlers to return a numeric status code
5cdddd3 lib: add limit support to split() and replace()
0ba9c3e fs: add optional third permission argument to fs.open()
c1f7b3b lib: remove fixed capture group limit in match() and regex replace()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
add Flow Queuing with Proportional Integral controller Enhanced (FQ-PIE) as an
optional kmod in network support and extract sched-pie from kmod-sched to
allow dependency on just kmod-sched-pie (PIE).
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
Add support for the TP-Link SG2210P switch. This is an RTL8380 based
switch with eight RJ-45 ports with 802.3af PoE, and two SFP ports.
This device shares the same board with the SG2008P and SG2008. To
model this, declare all the capabilities in the sg2xxx dtsi, and
disable unpopulated on the lower end models.
Specifications:
---------------
- SoC: Realtek RTL8380M
- Flash: 32 MiB SPI flash (Vendor varies)
- RAM: 256 MiB (Vendor varies)
- Ethernet: 8x 10/100/1000 Mbps with PoE (all ports)
2x SFP ports
- Buttons: 1x "Reset" button on front panel
- Power: 53.5V DC barrel jack
- UART: 1x serial header, unpopulated
- PoE: 2x TI TPS23861 I2C PoE controller
Works:
------
- (8) RJ-45 ethernet ports
- (2) SFP ports (with caveats)
- Switch functions
- System LED
Not yet enabled:
----------------
- Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
- PoE LEDs
Enabling SFP ports:
-------------------
The SFP port control lines are hardwired, except for tx-disable. These
lines are controller by the RTL8231 in shift register mode. There is
no driver support for this yet.
However, to enable the lasers on SFP1 and SFP2 respectively:
echo 0x0510ff00 > /sys/kernel/debug/rtl838x/led/led_p_en_ctrl
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.26
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.24
Install via serial console/tftp:
--------------------------------
The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.
The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWrt:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U7)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as sson as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWrt.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[OpenWrt capitalisation in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Serge Vasilugin reports:
To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
a) RF and BBP regs never be corrected for this mode
b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough
First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA
Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
35-40/30-35 Mbps for HT20
65-70/60-65 Mbps for HT40
Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Prepare patches for sending upstream by adding patch descriptions
generated from the original OpenWrt commits adding each patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)
Installation:
- Flash recovery image with TFTP recovery
Revert to stock firmware:
- Flash stock firmware with TFTP recovery
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
xdp-tools build currently breaks on build hosts which do not have
libbpf headers installed because the build system wrongly tries to
use the host's include path.
Properly pass path to libbpf headers to xdp-tools build system to
fix build e.g. on the buildbots.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for TP-Link Deco S4 wifi router
The label refers to the device as S4R and the TP-Link firmware
site calls it the Deco S4 v2. (There does not appear to be a v1)
Hardware (and FCC id) are identical to the Deco M4R v2 but the
flash layout is ordered differently and the OEM firmware encrypts
some config parameters (including the label mac address) in flash
In order to set the encrypted mac address, the wlan's caldata
node is removed from the DTS so the mac can be decrypted with
the help of the uencrypt tool and patched into the wlan fw
via hotplug
Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR
UART serial access (115200N1) on board via solder pads:
RX = TP1 pad
TX = TP2 pad
GND = C201 (pad nearest board edge)
The device's bootloader and web gui will only accept images that
were signed using TP-Link's RSA key, however a memory safety bug
in the bootloader can be leveraged to install openwrt without
accessing the serial console. See developer forum S4 support page
for link to a "firmware" file that starts a tftp client, or you
may generate one on your own like this:
```
python - > deco_s4_faux_fw_tftp.bin <<EOF
import sys
from struct import pack
b = pack('>I', 0x00008000) + b'X'*16 + b"fw-type:" \
+ b'x'*256 + b"S000S001S002" + pack('>I', 0x80060200) \
b += b"\x00"*(0x200-len(b)) \
+ pack(">33I", *[0x3c0887fc, 0x35083ddc, 0xad000000, 0x24050000,
0x3c048006, 0x348402a0, 0x3c1987f9, 0x373947f4,
0x0320f809, 0x00000000, 0x24050000, 0x3c048006,
0x348402d0, 0x3c1987f9, 0x373947f4, 0x0320f809,
0x00000000, 0x24050000, 0x3c048006, 0x34840300,
0x3c1987f9, 0x373947f4, 0x0320f809, 0x00000000,
0x24050000, 0x3c048006, 0x34840400, 0x3c1987f9,
0x373947f4, 0x0320f809, 0x00000000, 0x1000fff1,
0x00000000])
b += b"\xff"*(0x2A0-len(b)) + b"setenv serverip 192.168.0.2\x00"
b += b"\xff"*(0x2D0-len(b)) + b"setenv ipaddr 192.168.0.1\x00"
b += b"\xff"*(0x300-len(b)) + b"tftpboot 0x81000000 initramfs-kernel.bin\x00"
b += b"\xff"*(0x400-len(b)) + b"bootm 0x81000000\x00"
b += b"\xff"*(0x8000-len(b))
sys.stdout.buffer.write(b)
EOF
```
Installation:
1. Run tftp server on pc with static ip 192.168.0.2
2. Place openwrt "initramfs-kernel.bin" image in tftp root dir
3. Connect pc to router ethernet port1
4. While holding in reset button on bottom of router, power on router
5. From pc access router webgui at http://192.168.0.1
6. Upload deco_s4_faux_fw_tftp.bin
7. Router will load and execture in-memory openwrt
8. Switch pc back to dhcp or static 192.168.1.x
9. Flash openwrt sysupgrade image via luci/ssh at 192.168.1.1
Revert to stock:
Press and hold reset button while powering device to start the
bootloader's recovery mode, where stock firmware can be uploaded
via web gui at 192.168.0.1
Please note that one additional non-github commits is also needed:
firmware-utils: add tplink-safeloader support for Deco S4
Signed-off-by: Nick French <nickfrench@gmail.com>
FCC ID: U2M-CAP2100AG
WatchGuard AP100 is an indoor wireless access point with
1 Gb ethernet port, dual-band but single-radio wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP300 v2
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz AND 5 GHz WMAC, 2x2
- AR8035-A EPHY RGMII GbE with PoE+ IN
- 25 MHz clock
- 16 MB FLASH mx25l12805d
- 2x 64 MB RAM
- UART console J11, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 2 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
Label has no MAC
Only one Vendor MAC address in flash at art 0x0
eth0 ---- *:e5 art 0x0 -2
phy0 ---- *:e5 art 0x0 -2
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell
It may be necessary to use a Watchguard router to flash the image to the AP
and / or to downgrade the software on the AP to access SSH
For some Watchguard devices, serial console over UART is disabled.
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
reset button has no function at boot time
only possible with modified uboot environment,
(see commit message for Watchguard AP300)
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM reliably
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For AR934x series, the PLL registers for eth0
can be see in the DTSI as 0x2c.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x1805002c 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Steve Wheeler <stephenw10@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: U2M-CAP4200AG
WatchGuard AP200 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP600
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI card 168c:0030, 5 GHz, 2x2, 26dBm
- AR8035-A EPHY RGMII GbE with PoE+ IN
- 25 MHz clock
- 16 MB FLASH mx25l12805d
- 2x 64 MB RAM
- UART console J11, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 4 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
Label has no MAC
Only one Vendor MAC address in flash at art 0x0
eth0 ---- *:be art 0x0 -2
phy1 ---- *:bf art 0x0 -1
phy0 ---- *:be art 0x0 -2
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell
It may be necessary to use a Watchguard router to flash the image to the AP
and / or to downgrade the software on the AP to access SSH
For some Watchguard devices, serial console over UART is disabled.
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
reset button has no function at boot time
only possible with modified uboot environment,
(see commit message for Watchguard AP300)
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM reliably
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For AR934x series, the PLL registers for eth0
can be see in the DTSI as 0x2c.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x1805002c 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Steve Wheeler <stephenw10@gmail.com>
Tested-by: John Delaney <johnd@ankco.net>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: Q6G-AP300
WatchGuard AP300 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card 168c:003c, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 32 MB FLASH S25FL512S
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 6 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:3c art 0x0
phy1 ---- *:3d ---
phy0 ---- *:3e ---
**Serial console access:**
For this board, its not certain whether UART is possible
it is likely that software is blocking console access
the RX line on the board for UART is shorted to ground by resistor R176
the resistors R175 and R176 are next to the UART RX pin at J10
however console output is garbage even after this fix
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell access
downgrade XTM firewall to v2.0.0.1
downgrade AP300 firmware: v1.0.1
remove / unpair AP from controller
perform factory reset with reset button
connect ethernet to a computer
login to OEM webpage with default address / pass: wgwap
enable SSHD in OEM webpage settings
access root shell with SSH as user 'root'
modify uboot environment to automatically try TFTP at boot time
(see command below)
rename initramfs-kernel.bin to test.bin
load test.bin over TFTP (see TFTP recovery)
(optionally backup all mtdblocks to have flash backup)
perform a sysupgrade with sysupgrade.bin
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
server ip: 192.168.1.101
reset button seems to do nothing at boot time...
only possible with modified uboot environment,
running this command in the root shell:
fw_setenv bootcmd 'if ping 192.168.1.101; then tftp 0x82000000 test.bin && bootm 0x82000000; else bootm 0x9f0a0000; fi'
and verify that it is correct with
fw_printenv
then, before boot, the device will attempt TFTP from 192.168.1.101
looking for file 'test.bin'
to return uboot environment to normal:
fw_setenv bootcmd 'bootm 0x9f0a0000'
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM
(see installation method 2)
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Alessandro Kornowski <ak@wski.org>
Tested-by: John Wagner <john@wagner.us.org>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Ruckus ZoneFlex 7321 is a dual-band, single radio 802.11n 2x2 MIMO enterprise
access point. It is very similar to its bigger brother, ZoneFlex 7372.
Hardware highligts:
- CPU: Atheros AR9342 SoC at 533 MHz
- RAM: 64MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi: AR9342 built-in dual-band 2x2 MIMO radio
- Ethernet: single Gigabit Ethernet port through AR8035 gigabit PHY
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the 7321-U variant.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
JTAG: Connector H5, unpopulated, similar to MIPS eJTAG, standard,
but without the key in pin 12 and not every pin routed:
------- H5
|1 |2 |
-------
|3 |4 |
-------
|5 |6 |
-------
|7 |8 |
-------
|9 |10|
-------
|11|12|
-------
|13|14|
-------
3 - TDI
5 - TDO
7 - TMS
9 - TCK
2,4,6,8,10 - GND
14 - Vref
1,11,12,13 - Not connected
Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw,
but with much less manual steps, and is generally recommended, being
safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
work on some rare versions of stock firmware. A more involved, and
requires installing `mkenvimage` from u-boot-tools package if you
choose to rebuild your own environment, but can be used without
disassembly or removal from installation point, if you have the
credentials.
If for some reason, size of your sysupgrade image exceeds 13312kB,
proceed with method [1]. For official images this is not likely to
happen ever.
[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0x9f040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7321-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7321_fw1_backup.bin
$ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7321_fw2_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin
[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
it boots, hold the reset button near Ethernet connectors for 5
seconds.
1. Connect the device to the network. It will acquire address over DHCP,
so either find its address using list of DHCP leases by looking for
label MAC address, or try finding it by scanning for SSH port:
$ nmap 10.42.0.0/24 -p22
From now on, we assume your computer has address 10.42.0.1 and the device
has address 10.42.0.254.
2. Set up a TFTP server on your computer. We assume that TFTP server
root is at /srv/tftp.
3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
frmware is pretty ancient and requires enabling HMAC-MD5.
$ ssh 10.42.0.254 \
-o UserKnownHostsFile=/dev/null \
-o StrictHostKeyCheking=no \
-o MACs=hmac-md5
Login. User is "super", password is "sp-admin".
Now execute a hidden command:
Ruckus
It is case-sensitive. Copy and paste the following string,
including quotes. There will be no output on the console for that.
";/bin/sh;"
Hit "enter". The AP will respond with:
grrrr
OK
Now execute another hidden command:
!v54!
At "What's your chow?" prompt just hit "enter".
Congratulations, you should now be dropped to Busybox shell with root
permissions.
4. Optional, but highly recommended: backup the flash contents before
installation. At your PC ensure the device can write the firmware
over TFTP:
$ sudo touch /srv/tftp/ruckus_zf7321_firmware{1,2}.bin
$ sudo chmod 666 /srv/tftp/ruckus_zf7321_firmware{1,2}.bin
Locate partitions for primary and secondary firmware image.
NEVER blindly copy over MTD nodes, because MTD indices change
depending on the currently active firmware, and all partitions are
writable!
# grep rcks_wlan /proc/mtd
Copy over both images using TFTP, this will be useful in case you'd
like to return to stock FW in future. Make sure to backup both, as
OpenWrt uses bot firmwre partitions for storage!
# tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7321_firmware1.bin -p 10.42.0.1
# tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7321_firmware2.bin -p 10.42.0.1
When the command finishes, copy over the dump to a safe place for
storage.
$ cp /srv/tftp/ruckus_zf7321_firmware{1,2}.bin ~/
5. Ensure the system is running from the BACKUP image, i.e. from
rcks_wlan.bkup partition or "image 2". Otherwise the installation
WILL fail, and you will need to access mtd0 device to write image
which risks overwriting the bootloader, and so is not covered here
and not supported.
Switching to backup firmware can be achieved by executing a few
consecutive reboots of the device, or by updating the stock firmware. The
system will boot from the image it was not running from previously.
Stock firmware available to update was conveniently dumped in point 4 :-)
6. Prepare U-boot environment image.
Install u-boot-tools package. Alternatively, if you build your own
images, OpenWrt provides mkenvimage in host staging directory as well.
It is recommended to extract environment from the device, and modify
it, rather then relying on defaults:
$ sudo touch /srv/tftp/u-boot-env.bin
$ sudo chmod 666 /srv/tftp/u-boot-env.bin
On the device, find the MTD partition on which environment resides.
Beware, it may change depending on currently active firmware image!
# grep u-boot-env /proc/mtd
Now, copy over the partition
# tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1
Store the stock environment in a safe place:
$ cp /srv/tftp/u-boot-env.bin ~/
Extract the values from the dump:
$ strings u-boot-env.bin | tee u-boot-env.txt
Now clean up the debris at the end of output, you should end up with
each variable defined once. After that, set the bootcmd variable like
this:
bootcmd=bootm 0x9f040000
You should end up with something like this:
bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup)
mtdids=nor0=ar7100-nor0
bootdelay=2
ethact=eth0
filesize=78a000
fileaddr=81000000
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=10.0.0.1
serverip=10.0.0.5
stdin=serial
stdout=serial
stderr=serial
These are the defaults, you can use most likely just this as input to
mkenvimage.
Now, create environment image and copy it over to TFTP root:
$ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
$ sudo cp u-boot-env.bin /srv/tftp
This is the same image, gzipped and base64-encoded:
H4sIAAAAAAAAA+3QQW7TQBQAUF8EKRtQI6XtJDS0VJoN4gYcAE3iCbWS2MF2Sss1ORDYqVq6YMEB3rP0
Z/7Yf+aP3/56827VNP16X8Zx3E/Cw8dNuAqDYlxI7bcurpu6a3Y59v3jlzCbz5eLECbt8HbT9Y+HHLvv
x9TdbbpJVVd9vOxWVX05TotVOpZt6nN8qilyf5fKso3hIYTb8JDSEFarIazXQyjLIeRc7PvykNq+iy+T
1F7PQzivmzbcLpYftmfH87G56Wz+/v18sT1r19vu649dqi/2qaqns0W4utmelalPm27I/lac5/p+OluO
NZ+a1JaTz8M3/9hmtT0epmMjVdnF8djXLZx+TJl36TEuTlda93EYQrGpdrmrfuZ4fZPGHzjmp/vezMNJ
MV6n6qumPm06C+MRZb6vj/v4Mk/7HJ+6LarDqXweLsZnXnS5vc9tdXheWRbd0GIdh/Uq7cakOfavsty2
z1nxGwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAD+1x9eTkHLAAAEAA==
7. Perform actual installation. Copy over OpenWrt sysupgrade image to
TFTP root:
$ sudo cp openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin /srv/tftp
Now load both to the device over TFTP:
# tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
# tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin -g 10.42.0.1
Vverify checksums of both images to ensure the transfer over TFTP
was completed:
# sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin
And compare it against source images:
$ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin
Locate MTD partition of the primary image:
# grep rcks_wlan.main /proc/mtd
Now, write the images in place. Write U-boot environment last, so
unit still can boot from backup image, should power failure occur during
this. Replace MTD placeholders with real MTD nodes:
# flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
# flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>
Finally, reboot the device. The device should directly boot into
OpenWrt. Look for the characteristic power LED blinking pattern.
# reboot -f
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Boot into OpenWrt initramfs as for initial installation. To do that
without disassembly, you can write an initramfs image to the device
using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Write factory images downloaded from manufacturer website into
fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
before installation:
mtd write ruckus_zf7321_fw1_backup.bin /dev/mtd1
mtd write ruckus_zf7321_fw2_backup.bin /dev/mtd5
4. Reboot the system, it should load into factory firmware again.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- The 5GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- U-boot disables JTAG when starting. To re-enable it, you need to
execute the following command before booting:
mw.l 1804006c 40
And also you need to disable the reset button in device tree if you
intend to debug Linux, because reset button on GPIO0 shares the TCK
pin.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Ruckus ZoneFlex 7372 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point.
Ruckus ZoneFlex 7352 is also supported, lacking the 5GHz radio part.
Hardware highligts:
- CPU: Atheros AR9344 SoC at 560 MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344 built-in 2x2 MIMO radio
- Wi-Fi 5Ghz: AR9582 2x2 MIMO radio (Only in ZF7372)
- Antennas:
- Separate internal active antennas with beamforming support on both
bands with 7 elements per band, each controlled by 74LV164 GPIO
expanders, attached to GPIOs of each radio.
- Two dual-band external RP-SMA antenna connections on "7372-E"
variant.
- Ethernet 1: single Gigabit Ethernet port through AR8035 gigabit PHY
- Ethernet 2: single Fast Ethernet port through AR9344 built-in switch
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on "-U" variants.
The same image should support:
- ZoneFlex 7372E (variant with external antennas, without beamforming
capability)
- ZoneFlex 7352 (single-band, 2.4GHz-only variant).
which are based on same baseboard (codename St. Bernard),
with different populated components.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1
---
|5|
---
|4|
---
|3|
---
|x|
---
|1|
---
Pin 5 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
JTAG: Connector H2, similar to MIPS eJTAG, standard,
but without the key in pin 12 and not every pin routed:
------- H2
|1 |2 |
-------
|3 |4 |
-------
|5 |6 |
-------
|7 |8 |
-------
|9 |10|
-------
|11|12|
-------
|13|14|
-------
3 - TDI
5 - TDO
7 - TMS
9 - TCK
2,4,6,8,10 - GND
14 - Vref
1,11,12,13 - Not connected
Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw,
but with much less manual steps, and is generally recommended, being
safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
work on some rare versions of stock firmware. A more involved, and
requires installing `mkenvimage` from u-boot-tools package if you
choose to rebuild your own environment, but can be used without
disassembly or removal from installation point, if you have the
credentials.
If for some reason, size of your sysupgrade image exceeds 13312kB,
proceed with method [1]. For official images this is not likely to
happen ever.
[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0x9f040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7372-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7372_fw1_backup.bin
$ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7372_fw2_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin
[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
it boots, hold the reset button near Ethernet connectors for 5
seconds.
1. Connect the device to the network. It will acquire address over DHCP,
so either find its address using list of DHCP leases by looking for
label MAC address, or try finding it by scanning for SSH port:
$ nmap 10.42.0.0/24 -p22
From now on, we assume your computer has address 10.42.0.1 and the device
has address 10.42.0.254.
2. Set up a TFTP server on your computer. We assume that TFTP server
root is at /srv/tftp.
3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
frmware is pretty ancient and requires enabling HMAC-MD5.
$ ssh 10.42.0.254 \
-o UserKnownHostsFile=/dev/null \
-o StrictHostKeyCheking=no \
-o MACs=hmac-md5
Login. User is "super", password is "sp-admin".
Now execute a hidden command:
Ruckus
It is case-sensitive. Copy and paste the following string,
including quotes. There will be no output on the console for that.
";/bin/sh;"
Hit "enter". The AP will respond with:
grrrr
OK
Now execute another hidden command:
!v54!
At "What's your chow?" prompt just hit "enter".
Congratulations, you should now be dropped to Busybox shell with root
permissions.
4. Optional, but highly recommended: backup the flash contents before
installation. At your PC ensure the device can write the firmware
over TFTP:
$ sudo touch /srv/tftp/ruckus_zf7372_firmware{1,2}.bin
$ sudo chmod 666 /srv/tftp/ruckus_zf7372_firmware{1,2}.bin
Locate partitions for primary and secondary firmware image.
NEVER blindly copy over MTD nodes, because MTD indices change
depending on the currently active firmware, and all partitions are
writable!
# grep rcks_wlan /proc/mtd
Copy over both images using TFTP, this will be useful in case you'd
like to return to stock FW in future. Make sure to backup both, as
OpenWrt uses bot firmwre partitions for storage!
# tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7372_firmware1.bin -p 10.42.0.1
# tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7372_firmware2.bin -p 10.42.0.1
When the command finishes, copy over the dump to a safe place for
storage.
$ cp /srv/tftp/ruckus_zf7372_firmware{1,2}.bin ~/
5. Ensure the system is running from the BACKUP image, i.e. from
rcks_wlan.bkup partition or "image 2". Otherwise the installation
WILL fail, and you will need to access mtd0 device to write image
which risks overwriting the bootloader, and so is not covered here
and not supported.
Switching to backup firmware can be achieved by executing a few
consecutive reboots of the device, or by updating the stock firmware. The
system will boot from the image it was not running from previously.
Stock firmware available to update was conveniently dumped in point 4 :-)
6. Prepare U-boot environment image.
Install u-boot-tools package. Alternatively, if you build your own
images, OpenWrt provides mkenvimage in host staging directory as well.
It is recommended to extract environment from the device, and modify
it, rather then relying on defaults:
$ sudo touch /srv/tftp/u-boot-env.bin
$ sudo chmod 666 /srv/tftp/u-boot-env.bin
On the device, find the MTD partition on which environment resides.
Beware, it may change depending on currently active firmware image!
# grep u-boot-env /proc/mtd
Now, copy over the partition
# tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1
Store the stock environment in a safe place:
$ cp /srv/tftp/u-boot-env.bin ~/
Extract the values from the dump:
$ strings u-boot-env.bin | tee u-boot-env.txt
Now clean up the debris at the end of output, you should end up with
each variable defined once. After that, set the bootcmd variable like
this:
bootcmd=bootm 0x9f040000
You should end up with something like this:
bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
bootdelay=2
mtdids=nor0=ar7100-nor0
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup)
ethact=eth0
filesize=1000000
fileaddr=81000000
ipaddr=192.168.0.7
serverip=192.168.0.51
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
stdin=serial
stdout=serial
stderr=serial
These are the defaults, you can use most likely just this as input to
mkenvimage.
Now, create environment image and copy it over to TFTP root:
$ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
$ sudo cp u-boot-env.bin /srv/tftp
This is the same image, gzipped and base64-encoded:
H4sIAAAAAAAAA+3QTW7TQBQAYB+AQ2TZSGk6Tpv+SbNBrNhyADSJHWolsYPtlJaDcAWOCXaqQhdIXOD7
Fm/ee+MZ+/nHu58fV03Tr/dFHNf9JDzdbcJVGGRjI7Vfurhu6q7ZlbHvnz+FWZ4vFyFM2mF30/XPhzJ2
X4+pe9h0k6qu+njRrar6YkyzVToWberL+HImK/uHVBRtDE8h3IenlIawWg1hvR5CUQyhLE/vLcpdeo6L
bN8XVdHFumlDTO1NHsL5mI/9Q2r7Lv5J3uzeL5bX27Pj+XjRdJZfXuaL7Vm73nafv+1SPd+nqp7OFuHq
dntWpD5tuqH6e+K8rB+ns+V45n2T2mLyYXjmH9estsfD9DTSuo/DErJNtSu76vswbjg5NU4D3752qsOp
zu8W8/z6dh7mN1lXto9lWx3eNJd5Ng5V9VVTn2afnSYuysf6uI9/8rQv48s3Z93wn+o4XFWl3Vg0x/5N
Vbbta5X9AgAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAID/+Q2Z/B7cAAAEAA==
7. Perform actual installation. Copy over OpenWrt sysupgrade image to
TFTP root:
$ sudo cp openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin /srv/tftp
Now load both to the device over TFTP:
# tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
# tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin -g 10.42.0.1
Verify checksums of both images to ensure the transfer over TFTP
was completed:
# sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin
And compare it against source images:
$ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin
Locate MTD partition of the primary image:
# grep rcks_wlan.main /proc/mtd
Now, write the images in place. Write U-boot environment last, so
unit still can boot from backup image, should power failure occur during
this. Replace MTD placeholders with real MTD nodes:
# flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
# flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>
Finally, reboot the device. The device should directly boot into
OpenWrt. Look for the characteristic power LED blinking pattern.
# reboot -f
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Boot into OpenWrt initramfs as for initial installation. To do that
without disassembly, you can write an initramfs image to the device
using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Write factory images downloaded from manufacturer website into
fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
before installation:
mtd write ruckus_zf7372_fw1_backup.bin /dev/mtd1
mtd write ruckus_zf7372_fw2_backup.bin /dev/mtd5
4. Reboot the system, it should load into factory firmware again.
Quirks and known issues:
- This is first device in ath79 target to support link state reporting
on FE port attached trough the built-in switch.
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
The 5GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- U-boot disables JTAG when starting. To re-enable it, you need to
execute the following command before booting:
mw.l 1804006c 40
And also you need to disable the reset button in device tree if you
intend to debug Linux, because reset button on GPIO0 shares the TCK
pin.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- Stock firmware has beamforming functionality, known as BeamFlex,
using active multi-segment antennas on both bands - controlled by
RF analog switches, driven by a pair of 74LV164 shift registers.
Shift registers used for each radio are connected to GPIO14 (clock)
and GPIO15 of the respective chip.
They are mapped as generic GPIOs in OpenWrt - in stock firmware,
they were most likely handled directly by radio firmware,
given the real-time nature of their control.
Lack of this support in OpenWrt causes the antennas to behave as
ordinary omnidirectional antennas, and does not affect throughput in
normal conditions, but GPIOs are available to tinker with nonetheless.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958:
https://kroks.ru/search/?text=1958
See Kroks OpenWrt fork for support of other models:
https://github.com/kroks-free/openwrt
Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 5x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- USB: 1x
- SIM-reader: 2x (driven by a dedicated chip with it's own firmware)
- Buttons: reset
- LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.)
Flashing:
- sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254
- U-Boot launches a WEB server if Reset button is held during power up,
IP: 192.168.1.1
MAC addresses as verified by OEM firmware:
vendor OpenWrt source
LAN eth0 factory 0x4 (label)
2g wlan0 label
Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
Aka "Kroks KNdRt31R19".
Ported from v19.07.8 of OpenWrt fork:
see https://github.com/kroks-free/openwrt
for support of other models.
Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- mPCIe: 1x (usually equipped with an LTE modem by vendor)
- Buttons: reset
- LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status
Flashing:
- sysupgrade image via stock firmware WEB interface.
- U-Boot launches a WEB server if Reset button is held during power up.
Server IP: 192.168.1.1
SIM card switching:
The device supports up to 4 SIM cards - 2 locally on board and 2 on
remote SIM-injector.
By default, 1-st local SIM is active.
To switch to e.g. 1-st remote SIM:
echo 0 > /sys/class/gpio/modem1power/value
echo 0 > /sys/class/gpio/modem1sim1/value
echo 1 > /sys/class/gpio/modem1rsim1/value
echo 1 > /sys/class/gpio/modem1power/value
MAC addresses as verified by OEM firmware:
vendor OpenWrt source
LAN eth0 factory 0x4 (label)
2g wlan0 label
Signed-off-by: Kroks <dev@kroks.ru>
[butirsky@gmail.com: port to master; drop dts-v1]
Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
This patch adds libbpf to the dependencies of tc-mod-iptables.
The package tc-mod-iptables is missing libbpf as a dependency,
which leads to the build failure described in bug #9491
LIBBPF_FORCE=on set, but couldn't find a usable libbpf
The build dependency is already automatically added because some other
packages from iproute2 depend on libbpf, but bpftools has multiple build
variants. With multiple build variants none gets build by default and
the build system will not build bpftools before iproute2.
Fixes: #9491
Signed-off-by: Kien Truong <duckientruong@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an RTL8393-based switch with 802.3af on all 48 ports.
Specifications:
---------------
* SoC: Realtek RTL8393M
* Flash: 32 MiB SPI flash
* RAM: 256 MiB
* Ethernet: 48x 10/100/1000 Mbps with PoE+
* Buttons: 1x "Reset" button, 1x "Speed" button
* UART: 1x serial header, unpopulated
* PoE: 12x TI TPS23861 I2C PoE controller, 384W PoE budget
* SFP: 4 SFP ports
Works:
------
- (48) RJ-45 ethernet ports
- Switch functions
- Buttons
- All LEDs on front panel except port LEDs
- Fan monitoring and basic control
Not yet enabled:
----------------
- PoE - ICs are not in AUTO mode, so the kernel driver is not usable
- Port LEDs
- SFP cages
Install via web interface:
-------------------------
Not supported at this time.
Install via serial console/tftp:
--------------------------------
The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. To install OpenWRT:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U6)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as soon as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWRT.
Blind install via tftp:
-----------------------
This method works when it's not feasible to install a serial header.
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
3. Watch network traffic (tcpdump or wireshark works)
4. Power on the device.
5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6)
6. When 192.168.0.30 makes tftp requests, release pin 16
7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Some platforms lack an established way to name netdevs; for example,
on x86, PCIe-based ethernet interfaces will be named starting from
eth0 in the order they are probed. This is a problem for many devices
supported explicitly by OpenWrt which have hard-wired, standalone or
on-CPU NICs not supported by DSA (which is usually used to rename the
ports based on their ostensible function).
To fix this, add a mapping between ethernet device name and sysfs
device path to board.json; this allows us to configure ethernet device
names we know about for a given board so that they correspond to
external labeling.
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
The GPIO used for the RST button is also used for PCIe-CLKREQ signal.
Hence it cannot be used as button signal if PCIe is also used.
Wire up WPS button to serve as KEY_RESTART in Linux and "reset" button
in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It allows prepopulating /etc/config/network interface-s with predefined
metric. It may be useful for devices with multiple WAN ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
btusb fails to start on MT792[12] hardware without the appropriate
firmware being loaded first:
[ 9.750285] bluetooth hci0: Direct firmware load for mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin failed with error -2
[ 9.765723] bluetooth hci0: Falling back to sysfs fallback for: mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin
Package firmware for MediaTek MT792[12] Bluetooth from linux-firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable MediaTek protocol in btusb module to support e.g. the Bluetooth
part of the MT7921K NGFF/M.2 module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Pakedge WR-1 is a dual-band wireless router.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
1. 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Rename initramfs image to:
openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
reset button. Hold the button, on the lates bootloader version, when
Power and WiFi-5 LEDs will start blinking release it. For the older
bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
minute) the Power LED will start blinking, when stops, router is fully
booted.
4. Connect to one of LAN ports and use SSH to open the shell at
192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
at some point, You want to go back to original firmware. The firmware
provided by manufacturer on its site is encrypted and U-Boot accepts
only decrypted factory images, so there's no way to restore original
firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
LED will start blinking, wait till it stops, then router is ready for
configuration.
Additional information
U-Boot command line is password protected. Password is unknown.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Devices using GPT usually have FAT filesystem on boot partition and
that's where the intermediary backup of system configuration is stored
on sysupgrade. Automatic restoring of OpenWrt configuration after
sysupgrade will be inhibited if the driver is not loaded and file system
type is not specified in mount command.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Update host build of fiptool and use the new python sptool.py instead
of the previous sptool executable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There are two feature currently altered by the multicast_to_unicast option.
1. bridge level multicast_to_unicast via IGMP snooping
2. hostapd/mac80211 config multicast_to_unicast setting
The hostapd/mac80211 setting has the side effect of converting *all* multicast
or broadcast traffic into per-station duplicated unicast traffic, which can
in some cases break expectations of various protocols.
It also has been observed to cause ARP lookup failure between stations
connected to the same interface.
The bridge level feature is much more useful, since it only covers actual
multicast traffic managed by IGMP, and it implicitly defaults to 1 already.
Renaming the hostapd/mac80211 option to multicast_to_unicast_all should avoid
unintentionally enabling this feature
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit 0b7c66c ("at91bootstrap: add sama5d27_som1_eksd1_uboot as
default defconfig") changed default booting media for sama5d27_som1_ek
board w/o any reason. Changed it back to sdmmc0 as it is for all the
other Microchip supported distributions for this board (Buildroot,
Yocto Project). The initial commit cannot be cleanly reverted.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Commit adc69fe (""uboot-at91: changed som1 ek default defconfigs")
changed the booting media to sdmmc1 as default booting w/o any reason.
The Microchip releases for the rest of supported distributions (Buildroot,
Yocto Project) uses sdmmc0 as default booting media for this board.
Thus change it back to sdmmc0. With this remove references to sdmmc1
config. The initial commit cannot be cleanly reverted.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
f5d02c32f811 pex: add support for sending endpoint notification from the wg port via raw socket
c3b1127236a0 ubus: add support for querying active networks
8ad119715168 ubus: add support for adding auth_connect hosts at runtime
26dc52789d41 network: add support for configuring extra peers via a separate json file
d7fb9e5b065b ubus: add reload command
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f5fcdcf cli: introduce test mode and refuse firewall restart on errors
a540f6d fw4: fix cosmetic issue with per-ruleset and per-table include paths
695e821 doc: fix swapped include positions in nftables.d README
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Weijie Gao has submitted an updated version of the patchset adding
support for MT7986 and MT7981 to U-Boot. Use that v2 patchset.
Changes of v2:
- Add cpu driver for print_cpuinfo()
- Fix NULL pointer dereference in mtk_image
(was already fixed in OpenWrt)
- Fix coding style
- Minor changes
https://patchwork.ozlabs.org/project/uboot/list/?series=316148
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Create new mediatek_filogic file and add entries for environment on
MMC, UBI and NOR for the Bananapi BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bananapi BPi-R3 board can boot from eMMC, SD card, SPI-NAND and
SPI-NOR, depending on the position of switches controlling the BOOTSEL
bootstrap pins as we as hard-wired chip-select lines. The position of the
chip-select switch SW6 decides whether either SD card or eMMC can be
accessed, SW5 selects either SPI-NAND or SPI-NOR.
Generate U-Boot for all 4 boot options. The SD card version allows
installation to SPI-NAND and SPI-NOR (eMMC cannot be accessed
simultanously with the SD card), the SPI-NAND version allows installation
to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Testing has shown it to be very unreliable in variety of configurations.
It is not mandatory, so let's disable it by default until we have a better
solution.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
344fa9e lib: extend render() to support function values
89452b2 lib: improve getenv() and split() implementations
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
b75791a6db25 scripts/update-cmd.pl: reorder add/remove calls to better deal with dynamic changes
c29e1ad045d0 scripts/update-cmd.pl: set device up before adding routes/addresses
5ad35ce4beea scripts/update-cmd.pl: run update two times
5d79b88f00c1 add support for overriding peer-exchange-port for individual hosts
0041fcacb624 add support for disabling VXLAN/eBPF support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
5cbd55f60346 unet-cli: fix formatting of help text
59b97448b636 build.sh: force use of -fPIC on static libraries to fix build error
74a14c00abb0 pex-msg: fix siphash key initializer
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This forces a rebuild of the wolfssl package when the
libwolfssl-benchmark OpenWrt package gets activated or deactivated.
Without this change the wolfssl build will fail when it compiled without
libwolfssl-benchmark before and it gets activated for the next build.
Fixes: 18fd12edb8 ("wolfssl: add benchmark utility")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Older MT7623 ARMv7 SoC as well as new Filogic platforms come with
inside-secure,safexcel-eip97 units. Enable them in DTS and select the
driver kernel module by default on those platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Treat missing compression node in FIT image as IH_COMP_NONE.
This is implicentely already happening in most places, but for now
was still triggering an annoying warning about initramfs compression
being obsolete despite compression note being absent.
Fix this.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* updated SNAND/SNFI driver brings support for MT7981
* add support for MediaTek NAND Memory bad Block Management (NMBM)
(not used for any boards atm, but could be useful in future)
* wire up NMBM support for MT7622, MT7629, MT7981 and MT7986
* replace some local patches with updated version from SDK
* bring some legacy precompiler symbols which haven't been converted
into Kconfig symbols in U-Boot 2022.07, remove when bumbping to
U-Boot 2022.10:
100-28-include-configs-mt7986-h-from-SDK.patch
Source: https://github.com/mtk-openwrt/u-boot
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MediaTek's ARM Trusted Firmware v2.7+ allows the images inside a FIP
structure to be compressed. Make use of that for boards with NOR flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Truncating a UBI volume using `ubi write 0x0 volname 0x0` results in
segfault on newer U-Boot. Write 1MB of 0s instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The updated sources bring support for the MT798x Filogic SoC family.
Add builds for MT7986 with most supported storage types, each for DDR3
and DDR4 configurations.
A better solution for skipping bad blocks on SPI-NAND connected via the
SNFI interface has been implemented upstream, so drop local patch.
Add pending patches [1] and [2] to fix boot on existing MT7622 boards.
Tested on BananaPi BPi-R64 (SDMMC, eMMC, SPI-NAND), Linksys E8450 and
Ubiquiti UniFi 6 LR as well as upcoming Bananapi BPi-R3 board for which
support will be added in future patches.
[1]: https://github.com/mtk-openwrt/arm-trusted-firmware/pulls/#3
[2]: https://github.com/mtk-openwrt/arm-trusted-firmware/pulls/#4
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of relying on dtc being provided by the build host use the
dtc from $(LINUX_DIR) similar to how it's done also in u-boot.mk.
For this to work kernel.mk now needs to be included before
trusted-firmware-a.mk, add this include to all affected packages.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes from popt 1.16:
- fix an ugly and ancient security issue with popt failing to drop privileges on alias exec from a SUID/SGID program
- perform rudimentary sanity checks when reading in popt config files
- collect accumulated misc fixes (memleaks etc) from distros
- convert translations to utf-8 encoding
- convert old postscript documentation to pdf
- dust off ten years worth of autotools sediment
- reorganize and clean up the source tree for clarity
- remove the obnoxious splint annotations from the sources
Switch to new mirror:
http://ftp.rpm.org/popt/releases/
Switch URL to:
https://github.com/rpm-software-management/popt
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove upstreamed patch:
- 0001-meta-don-t-use-non-POSIX-formats-in-strptime.patch
Changes:
13248670 build: Bump version to 1.0.5
3432eebd tests/py: disable arp family for queue statement
180ce4d7 meta: don't use non-POSIX formats in strptime()
c1c223f1 src: allow anon set concatenation with ether and vlan
87c3041b evaluate: search stacked header list for matching payload dep
b1e3ed03 netlink_delinearize: also postprocess OP_AND in set element context
f680055c tests: add a test case for ether and vlan listing
dbd5f348 debug: dump the l2 protocol stack
0d9daa04 proto: track full stack of seen l2 protocols, not just cumulative offset
89688c94 netlink_delinearize: postprocess binary ands in concatenations
0542a431 netlink_delinearize: allow postprocessing on concatenated elements
8efab552 parser_json: fix device parsing in netdev family
76fae8f5 src: proto: support DF, LE PHB, VA for DSCP
446e76db doc: Document limitations of ipsec expression with xfrm_interface
a2ddb38f cache: report an error message if cache initialization fails
649b8ce3 cache: validate handle string length
64c74ba5 cache: prepare nft_cache_evaluate() to return error
46980cdd rule: crash when uncollapsing command with unexisting table or set
8a6cdfaf cache: release pending rules when chain binding lookup fails
e17337df evaluate: report missing interval flag when using prefix/range in concatenation
45c097c6 scanner: allow prefix in ip6 scope
6c23bfa5 segtree: fix map listing with interface wildcard
8623772a scanner: don't pop active flex scanner scope
994bf500 parser: add missing synproxy scope closure
ed2426bc tests/py: Add a test for failing ipsec after counter
27107b49 evaluate: fix segfault when adding elements to invalid set
0f82b07f mnl: store netlink error location for set elements
15b3be2e src: remove NFT_NLATTR_LOC_MAX limit for netlink location error reporting
f56e901a parser_bison: fix error location for set elements
6d1ee926 intervals: check for EXPR_F_REMOVE in case of element mismatch
5357cb7b intervals: fix crash when trying to remove element in empty set
d54510f8 netlink_delinearize: memleak when parsing concatenation data
12a223ce libnftables: release top level scope
b91bbf88 optimize: limit statement is not supported yet
45a61a75 optimize: assume verdict is same when rules have no verdict
fa409176 optimize: only merge OP_IMPLICIT and OP_EQ relational
29e62111 tests: shell: run -c -o on ruleset
887405df optimize: add unsupported statement
8f61a69e optimize: add hash expression support
ca8fd77a optimize: add numgen expression support
721efd64 optimize: add binop expression support
f7e901a2 optimize: add fib expression support
54b1e49f optimize: add xfrm expression support
0beaea37 optimize: add osf expression support
d07fe8e8 optimize: fix verdict map merging
38d48fe5 optimize: fix reject statement
f9939f89 optimize: remove comment after merging
8f10f33a optimize: do not print stateful information
3ac932e9 optimize: do not merge rules with set reference in rhs
64ebb03a optimize: do not compare relational expression rhs when collecting statements
59e3a592 intervals: Do not sort cached set elements over and over again
d434de8b intervals: do not empty cache for maps
87ba510f intervals: do not report exact overlaps for new elements
498a5f0c rule: collapse set element commands
8fafe4e6 tests: shell: runtime set element automerge
638af0ce Revert "scanner: flags: move to own scope"
Signed-off-by: Nick Hainke <vincent@systemli.org>
Instead of defining the MIN version it is enough to include "#include
<sys/param.h>".
Delete patch:
- 105-ipstats-Define-MIN-function-to-fix-undefined-referen.patch
Add patch:
- 010-ipstats-Add-param.h-for-musl.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Use 4k sectors when accessing the U-Boot environment on the 64MiB
SPI-NOR flash chip found in the UniFi 6 LR. The speeds up environment
write access as only 4kB instead of 64kB have to be written.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Image names as well as the calculation of the padded image size did
not work as intended. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
35fec487e3 fixed opkg usage,
but when using buildroot we were still defaulting to
ip(6)tables-legacy
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
This package simplifies setting up wireguard networks on OpenWrt by a wireguard
network as a JSON file, which can be shared across all participating nodes.
It can be signed with an authentication key and automatically kept in sync.
unetd also supports deterministically generating ipv6 addresses for each host
based on the public key and storing those in a hosts file that can be used with
dnsmasq. It also supports automatically creating VXLAN tunnels between multiple
endpoints.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
gcc 10 with -O2 reports following:
In function ‘strncpy’,
inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:244:4:
/usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation]
106 | return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function ‘strncpy’,
inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:227:4:
/usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation]
106 | return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Since it is not possible to avoid truncation by strncpy, it is necessary
to make sure the result of strncpy is properly NUL-terminated and the
NUL must be inserted explicitly, after strncpy has returned.
References: #10442
Reported-by: Alexey Smirnov <s.alexey@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
a4484d4 fw4: support automatic includes
ca7e3a1 fw4: honour enabled option of include sections
5a02f74 tests: add missing fs.stat) mock data for `nf_conntrack_dummy`
111a7f7 fw4: don't inherit zone family from ct helpers
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
e3395cd ucode: initialize search path before VM init
8cb3f85 ucode: initialize default library search path
188dea2 utils: accept '?' as path terminator in uh_path_match()
c5eac5d file: support using dynamic script handlers as error pages
290ff88 relay: trigger close if in header read state with pending data
f9db538 ucode: ignore exit exceptions
8ba0b64 cmake: use variables and find_library for dependency
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
bcdd2cb examples: add module search path initialization and freeing
ee1946f ubus: fix GCC strncpy() truncation warning
131d99c lib: introduce three new functions call(), loadstring() and loadfile()
8e8dae0 lib: introduce helper function for indenting error messages
476f02b lib: simplify include_path()
d84b53a source: avoid null pointer access in uc_source_runpath_set()
c43a54f types: gracefully handle unpatched upvalues in ucv_free()
e2fb11a README.md: document gc() function
b41cb2d main: introduce -g flag to allow enabling periodic gc from cli
85d7885 lib: implement gc()
47528f0 vm: support automatic periodic GC runs
381cc75 types: treat vm->exports as GC roots
fcc49e6 compiler: add import statement support for dynamic extensions
c9442f1 vm: introduce new I_DYNLOAD opcode
b6fd8a2 lib: internally expose new uc_require_library() helper
a486adc vm: don't treat offset 0 special for exceptions
41ccd19 compiler: don't treat offset 0 special at syntax errors
b4a3f68 compiler: improve formatting of nested syntax error messages
5d5dadc program: remove now unused uc_program_export_lookup()
304995b compiler: rework export index allocation
506cc37 compiler: fix deriving module path from source runpath
54b7fac compiler: enforce stricter module compilation rules
d62e372 vm: don't initialize upvalues for module functions
b856602 program: add serialization and deserialization for module function flag
d7d1bde compiler: add a flag denoting module functions
156d584 treewide: unexport libucode internal functions
10e056d compiler: add support for import/export statements
862e49d compiler: resolve predeclared upvalues
78dfb08 compiler: require a name in function declarations
afd78c1 compiler: fix reported source position in inc/dec operator error
e1c3db0 tests: run_tests.sh: substitute dynamic test directory path in output
3c168b5 vm, cli: move search path into global configuration structure
d85bc71 vm: introduce import and export opcodes
365782e vm: honor constant flag of objects and arrays
6becc64 vm: transparently resolve upvalue references
3418967 vm: gracefully handle unresolved upvalues
50cf572 program: add function to globally lookup exported name
c441f65 program: add infrastructure to handle multiple sources per program
2322468 program: fix reporting source position of first instruction
9c9a9ec program: fix en/decoding debuginfo upvalue slots in precompiled bytecode
41114a0 source: add tracking of exported symbols
70ae304 lib: honor constant flag of arrays
3c104f5 types: resolve upvalue references on stringification
3a6f9cb types: add ability to mark array and object values as constant
b738f3a lexer: recognize module related keywords
03c8e4b lexer: rewrite token scanner
fd433aa lexer: fix parsing with disabled block left stripping
557577a rtnl: fix parsing/creation of IFLA_AF_SPEC RTA for the AF_BRIDGE family
35c6b73 compiler: fix stack mismatch on continue statements nested in switches
f673096 uloop: end uloop on exceptions in managed code
2e5426c ubus: end uloop on exceptions in managed code
c024270 rtnl: expose IFLA_STATS64 contents
d3c58c0 rtnl: expose ifinfomsg.ifi_change member
c4dde50 rtnl: update NETLINK_GET_STRICT_CHK socket flag with every request
7ef0d02 nl80211: fix NL80211_SURVEY_INFO_NOISE datatype
9a2e592 compiler: fix stack mismatch on nonmatching switch statements with locals
03c8ca5 nl80211: recognize further NL80211_STA_INFO_* NLAs
a1ed566 struct: add optional offset argument to `unpack()`
230e595 rtnl: fix segmentation fault on parsing linkinfo RTA without data
523566d rtnl: zero request message headers
56be30d rtnl: fix premature netlink reply receive abort
1347440 rtnl: avoid stray "netlink: %d bytes leftover after parsing attributes."
44b0a3b struct: fix packing `*` format after other repeated formats
Also package uloop binding module which has been introduced by a previous
ucode update and introduce a host build with the basic set of modules.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
WPA3 enterprise requires group_mgmt_cipher=BIP-GMAC-256 and if 802.11r is
active also wpa_key_mgmt FT-EAP-SHA384. This commit also requires
corresponding changes in netifd.
Signed-off-by: Joerg Werner <schreibubi@gmail.com>
It is common for 802.11ax NICs to support more than just AP mode, which
results in there being a distinct set of HE capabilities for each mode. As
(bad) luck would have it, iw prints out info for each HE mode in sequential
order according to `enum nl80211_iftype`, and AP mode isn't always first.
As a result, the wrong set of HE capabilities can be parsed if an AP NIC
supports station (managed) mode or any other mode preceding AP mode, since
only the first set of HE capabilities printed by iw is parsed from awk's
output.
This has a noticeable impact on beamforming for example, since managed mode
usually doesn't have beamformer capabilities enabled, while AP mode does.
Hostapd won't be set up with the configs to enable beamformer capabilities
in this scenario, causing hostapd to disable beamforming to HE stations
even when it's supported by the AP.
Always parse the correct set of HE capabilities for AP mode to fix this.
This is achieved by trimming all of iw's output prior to the AP mode
capabilities, which ensures that the first set of HE capabilities are
always for AP mode.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
General hardware info:
-------------------------------------------------------------------------------
D-Link DGS-1210-10MP is a switch with 8 ethernet ports and 2 SFP ports, all
ports Gbit capable. It is based on a RTL8380 SoC @ 500MHz, DRAM 128MB and
32MB flash. All ethernet ports are 802.3af/at PoE capable
with a total PoE power budget of 130W.
File info:
-------------------------------------------------------------------------------
The dgs-1210-10mp is very similar to dgs-1210-10p so I used that as a start.
rtl838x.mk:
- Removed lua-rs232 package since it was a leftover from the old rtl83xx-poe
package.
- Updated the soc to 8380.
- Specified device variant: F.
- Installed the new realtek-poe package.
rtl8380_d-link_dgs-1210-10mp.dts:
- Moved dgs-1210 family common parts and non PoE related ports on rtl8231
to the new device tree dtsi files.
Serial connection:
-------------------------------------------------------------------------------
The UART for the SoC (115200 8N1) is available close to the front panel next
to the LED/key card connector via unpopulated standard 0.1" pin header
marked j4. Pin1 is marked with arrow and square.
Pin 1: Vcc 3,3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd
Installation with TFTP from u-boot
-------------------------------------------------------------------------------
I originally used the install procedure:
'OpenWrt installation using the TFTP method and serial console access' found
in the device wiki for the dgs-1210-16.
< https://openwrt.org/toh/d-link/dgs-1210-16_g1#openwrt_installation_using
_the_tftp_method_and_serial_console_access >
About the realtek-poe package
-------------------------------------------------------------------------------
The realtek-poe package is installed but there isn't any automatic PoE config
setting at this time so for now the PoE config must be edited manually.
Original OEM hardware/firmware data at first installation
-------------------------------------------------------------------------------
It has been installed, developed, and tested on a device with these OEM
hardware and firmware versions.
- U-boot: 2011.12.(2.1.5.67086)-Candidate1 (Jun 22 2020 - 15:03:58)
- Boot version: 1.01.001
- Firmware version: 6.20.007
- Hardware version: F1
Things to be done when support are developed
-------------------------------------------------------------------------------
- realtek-poe has been included in OpenWrt but the automatic config handling
has not been solved yet so in the future there will probably be some minor
updates for this device to handle the poe config.
- LED link_act and poe are per function supposed to be connected to the PoE
system.
But some software development is also needed to make this LED work and
shift the LED array between act and poe indication and to shift the mode
lights with mode key.
- LED poe_max should probably be used as straight forward error output from
the realtek-poe package error handling. But no code has been written for
this.
- SFP is currently not hot pluggable. Development is under progress to get
working I2C communication with SFP and have them hot pluggable.
When any device in the dgs-1210 family gets this working, I expect it
should be possible to implement the same solution in this device.
Signed-off-by: Daniel Groth <flygarn12@gmail.com>
[Capitalisation of abbreviations, DEVICE_VARIANT and update filenames,
device compatibles on single line]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Modify uencrypt to support any cipher provided by ssl library.
Original tool supported only AES-128-CBC to decrypt the config
mtd of Arcadyan WG430223/WG443223.
TP-Link Deco S4 has mtd configuration encrypted with DES-ECB,
so make the cipher generic to support both routers.
Signed-off-by: Nick French <nickfrench@gmail.com>
Reviewed-by: Eneas U de Queiroz >cotequeiroz@gmail.com>
Some Arcadyan devices (e.g. MTS WG430223) keep their config in encrypted
mtd. This adds mtd_get_mac_encrypted_arcadyan() function to get the MAC
address from the encrypted partition. Function uses uencrypt utility for
decryption (and openssl if the uencrypt wasn't found).
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
In the SDK the folder $(LINUX_DIR)/user_headers/include does not exist,
but it more or less contains the same content as
$(LINUX_DIR)/include/uapi which also exists in the SDK.
Since iproute2 commit 1d819dcc741e ("configure: fix parsing issue on
include_dir option") it checks if this folder exists and aborts the
build if it does not exists.
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/commit/?id=1d819dcc741e25958190e31f8186c940713fa0a8
With this commit the KERNEL_INCLUDE variable points to a valid folder
with the kernel include headers. I am not sure if they are actually
needed because the build worked before even with an invalid path.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is no WLAN_STA_MBO flag, but according to the hostapd source code,
when an STA does not support MBO, cell_capa will be 0. Use this to
indicate MBO support in the get_clients ubus method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: David Bauer <mail@david-bauer.net>
There is only one module in kmod-sched that depends on iptables. Move it
to its own kmod package so we can drop the kmod-ipt-core dependency from
kmod-sched. This makes it possible to disable all kmod-ipt-* packages
without having to disable kmod-sched. Since we now default to firewall4
and nftables, we should avoid iptables dependencies where we can.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This reverts commit cc24c4ed5e.
binutils does not compile with glibc:
Package binutils is missing dependencies for the following libraries:
libgprofng.so.0
libmsgpackc.so.2
libstdc++.so.6
libbpf does not compile against binutils 2.39 any more, see:
https://github.com/libbpf/bpftool/issues/30
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
8c213b0 libfstools: Rename move_mount() function to ovl_move_mount() for glibc 2.36
81785c1 block: Do not include linux/fs.h any more
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following build error:
Package kmod-hwmon-tps23861 is missing dependencies for the following libraries:
regmap-i2c.ko
Fixes: b664646db7 ("kernel: add kmod-hwmon-tps23861 support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changes:
* The ELF linker will now generate a warning message if the stack is made
executable. Similarly it will warn if the output binary contains a
segment with all three of the read, write and execute permission
bits set. These warnings are intended to help developers identify
programs which might be vulnerable to attack via these executable
memory regions.
The warnings are enabled by default but can be disabled via a command
line option. It is also possible to build a linker with the warnings
disabled, should that be necessary.
* The ELF linker now supports a --package-metadata option that allows
embedding a JSON payload in accordance to the Package Metadata
specification.
* In linker scripts it is now possible to use TYPE=<type> in an output
section description to set the section type value.
* The objdump program now supports coloured/colored syntax
highlighting of its disassembler output for some architectures.
(Currently: AVR, RiscV, s390, x86, x86_64).
* The nm program now supports a --no-weak/-W option to make it ignore
weak symbols.
* The readelf and objdump programs now support a -wE option to prevent
them from attempting to access debuginfod servers when following
links.
* The objcopy program's --weaken, --weaken-symbol, and
--weaken-symbols options now works with unique symbols as well.
Announcement:
https://sourceware.org/pipermail/binutils/2022-August/122246.html
Signed-off-by: Nick Hainke <vincent@systemli.org>
With the 5.18 and 5.19 update ip-tiny grows in size. Remove some
features bringing it back to the size before 5.18.
Remove
- Identifier-locator addressing (ila)
- MACsec Device Configuration (macsec)
- Multicast Routing Cache Management (mroute)
- mrule
- Virtual Routing and Forwarding (vrf)
- Segment Routing (sr)
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add patch:
- 105-ipstats-Define-MIN-function-to-fix-undefined-referen.patch
Refreshed:
- 170-ip_tiny.patch
- 195-build_variant_ip_tc.patch
Changes:
deb48554 v5.19.0
f8decf82 bpf_glue: include errno.h
71178ae0 rdma: update uapi/ib_user_verbs.h
96594fd2 vdpa: update uapi headers from 5.19-rc7
30c7b77f Revert "uapi: add vdpa.h"
c5433c4b ip neigh: Fix memory leak when doing 'get'
2cb76253 mptcp: Fix memory leak when getting limits
afdbb020 mptcp: Fix memory leak when doing 'endpoint show'
6db01afd bridge: Fix memory leak when doing 'fdb get'
1d540336 ip address: Fix memory leak when specifying device
325f706b uapi: add virtio_ring.h
291898c5 uapi: add vdpa.h
6e2fb804 uapi: update bpf.h
329fda18 ip: Fix size_columns() invocation that passes a 32-bit quantity
2a00a4b1 man: tc-fq_codel: add drop_batch
6bf5abef uapi: update mptcp.h
02410392 ip: Fix size_columns() for very large values
ed243312 man: tc-ct.8: fix example
2bb37e90 l2tp: fix typo in AF_INET6 checksum JSON print
855edb3d man: tc-fq_codel: Fix a typo.
4044a453 tc: declaration hides parameter
a44a7918 genl: fix duplicate include guard
703f2de6 uapi: change name for zerocopy sendfile in tls
248ad98e uapi: update socket.h
11e41a63 ip: Convert non-constant initializers to macros
8d3977ef Update kernel headers
5a1ad9f8 man: ip-stats.8: Describe groups xstats, xstats_slave and afstats
d9976d67 ipstats: Expose bond stats in ipstats
36e10429 ipstats: Expose bridge stats in ipstats
79f5ad95 iplink_bridge: Split bridge_print_stats_attr()
1247ed51 ipstats: Add groups "xstats", "xstats_slave"
c6900b79 ipstats: Add a third level of stats hierarchy, a "suite"
2ed73b9a iplink: Add JSON support to MPLS stats formatter
5ed8fd9d ipstats: Add a group "afstats", subgroup "mpls"
dff392fd iplink: Publish a function to format MPLS stats
72623b73 iplink: Fix formatting of MPLS stats
ce41750f ip: ipstats: Do not assume length of response attribute payload
40b50f15 bridge: vni: add support for stats dumping
c7f12a15 ip: iplink_vxlan: add support to set vnifiltering flag on vxlan device
45cd32f9 bridge: vxlan device vnifilter support
837294e4 libbpf: Remove use of bpf_map_is_offload_neutral
64e5ed77 libbpf: Remove use of bpf_program__set_priv and bpf_program__priv
ba6519cb libbpf: Use bpf_object__load instead of bpf_object__load_xattr
a6eb654d f_flower: add number of vlans man entry
5788732e f_flower: Check args with num_of_vlans
5ba31bcf f_flower: Add num of vlans parameter
b28eb051 man: Add man pages for the "stats" functions
a05a27c0 ipmonitor: Add monitoring support for stats events
0f1fd40c ipstats: Add offload subgroup "l3_stats"
179030fa ipstats: Add offload subgroup "hw_stats_info"
af5e7955 ipstats: Add a group "offload", subgroup "cpu_hit"
0517a2fd ipstats: Add a group "link"
df0b2c6d ipstats: Add a shell of "show" command
82f6444f ipstats: Add a "set" command
54d82b06 ip: Add a new family of commands, "stats"
5520cf16 ip: Publish functions for stats formatting
a463d6b1 libnetlink: Add filtering to rtnl_statsdump_req_filter()
38ae12d3 devlink: introduce -[he]x cmdline option to allow dumping numbers in hex format
bba95837 Update kernel headers
f6559bea ip-link: put types on man page in alphabetic order
ee53174b ip/iplink_virt_wifi: add support for virt_wifi
Signed-off-by: Nick Hainke <vincent@systemli.org>
The ip-tiny size grows from 124k (5.17.0) to 128k (5.18.0).
The update introduces a commit "configure: add check_libtirpc()" that
introduces a check for libtirpc. However, if libtirpc is already in the
staging directory due to an other dependency the check yields that the
library is installed and should be used resulting in failures like:
Package ss is missing dependencies for the following libraries:
libtirpc.so.3
To fix it add a patch making libtirpc optional again and setting it
"HAVE_TIRPC=n":
- 155-keep_tirpc_optional.patch
Fix patches:
- 130-no_netem_tipc_dcb_man_vdpa.patch
Refresh patches:
- 140-keep_libmnl_optional.patch
- 150-keep_libcap_optional.patch
- 180-drop_FAILED_POLICY.patch
- 200-drop_libbsd_dependency.patch
Changes:
6474b7c8 v5.18.0
4429a6c9 tipc: fix keylen check
6b6979b9 iplink: remove GSO_MAX_SIZE definition
19c3e009 doc: fix 'infact' --> 'in fact' typo
ed706c78 man: fix some typos
03589beb man: devlink-region: fix typo in example
b84fc332 tc: em_u32: fix offset parsing
b6d17086 uapi: update of virtio_ids
17bf51b7 libbpf: Remove use of bpf_map_is_offload_neutral
fa305925 libbpf: Remove use of bpf_program__set_priv and bpf_program__priv
9e0057b4 libbpf: Use bpf_object__load instead of bpf_object__load_xattr
e81fd551 devlink: fix "devlink health dump" command without arg
6f3b5843 man: use quote instead of acute accent
42d351fa man: 'allow to' -> 'allow one to'
d8a7a0f4 uapi: upstream update to stddef.h
5b2ff061 uapi: update from 5.18-rc1
292509f9 ss: remove an implicit dependency on rpcinfo
1ee309a4 configure: add check_libtirpc()
41848100 ip/geneve: add support for IFLA_GENEVE_INNER_PROTO_INHERIT
28add137 f_flower: Implement gtp options support
b25599c5 ip: GTP support in ip link
e4880869 man: bridge: document per-port mcast_router settings
9e82e828 bridge: support for controlling mcast_router per port
f1d18e2e Update kernel headers
8130653d vdpa: Update man page with added support to configure max vq pair
56eb8bf4 vdpa: Support reading device features
16482fd4 vdpa: Support for configuring max VQ pairs for a device
bd91c764 vdpa: Allow for printing negotiated features of a device
2d1954c8 vdpa: Remove unsupported command line option
93fb6810 Makefile: move HAVE_MNL check to top-level Makefile
2dee2101 man: ip-link: whitespace fixes to odd line breaks mid sentence
609b90aa man: ip-link: mention bridge port's default mcast_flood state
b1c3ad84 man: ip-link: document new bcast_flood flag on bridge ports
c354a434 ip: iplink_bridge_slave: support for broadcast flooding
909f0d51 man: bridge: add missing closing " in bridge show mdb
3b681cf9 man: bridge: document new bcast_flood flag for bridge ports
a6c848eb bridge: support for controlling flooding of broadcast per port
8acb5247 ip/batadv: allow to specify RA when creating link
0431d8e8 Import batman_adv.h header from last kernel sync point
239bfd45 Revert "configure: Allow command line override of toolchain"
a93c90c7 tc: separate action print for filter and action dump
d9977eaf bpf: Remove use of bpf_create_map_xattr
ac4e0913 bpf: Export bpf syscall wrapper
873bb975 bpf_glue: Remove use of bpf_load_program from libbpf
5e17b715 ss: display advertised TCP receive window and out-of-order counter
712ec66e tc: bash-completion: Add profinet and ethercat to procotol completion list
75061b35 lib: add profinet and ethercat as link layer protocol names
0a685b98 man8/ip-link.8: add locked port feature description and cmd syntax
d4fe3673 man8/bridge.8: add locked port feature description and cmd syntax
092af16b ip: iplink_bridge_slave: add locked port flag support
0e51a185 bridge: link: add command to set port in locked mode
04a0077d Update kernel headers
386ae64c configure: Allow command line override of toolchain
bea92cb0 mptcp: add port support for setting flags
2dbc6c90 mptcp: add fullmesh support for setting flags
5fb6bda0 mptcp: add fullmesh check for adding address
9831202f bond: add ns_ip6_target option
e8fd4d4b devlink: Remove strtouint8_t in favor of get_u8
2688abf0 devlink: Remove strtouint16_t in favor of get_u16
95c03f40 devlink: Remove strtouint32_t in favor of get_u32
7cb0e24d devlink: Remove strtouint64_t in favor of get_u64
7848f6bb Update kernel headers
4f015972 f_flower: fix indentation for enc_key_id and u32
25a9c4fa tunnel: Fix missing space after local/remote print
ff14875e Update documentation
8908cb25 Add support for the IOAM insertion frequency
cd24451e Update kernel headers
e4ba36f7 iplink: add ip-link documentation
5d57e130 iplink: add gro_max_size attribute handling
721435dc tc: u32: add json support in `print_raw`, `print_ipv4`, `print_ipv6`
c733722b tc: u32: add support for json output
5f44590d tc/f_flower: fix indentation
9948b6cb tc_util: fix breakage from clang changes
f4cd4f12 tc: add skip_hw and skip_sw to control action offload
ba5ac984 json_print: suppress clang format warning
bf71c8f2 libbpf: fix clang warning about format non-literal
5632cf69 tunnel: fix clang warning
c0248878 tipc: fix clang warning about empty format string
371c13e8 can: fix clang warning
8d27eee5 ipl2tp: fix clang warning
560d2336 tc_util: fix clang warning in print_masked_type
b2450e46 flower: fix clang warnings
4e27d538 netem: fix clang warnings
9d5e29e6 utils: add format attribute
343c4f52 tc: add format attribute to tc_print_rate
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove backports:
- 0001-lib-fix-ax25.h-include-for-musl.patch
Changes:
4c424dfd v5.17.0
7846496b link_xfrm: if_id must be non zero
eed4bb1a testsuite: link xfrm delete no if_id test
ac0a54b2 rdma: make RES_PID and RES_KERN_NAME alternative to each other
885e281e uapi: update vdpa.h
19c0def1 ipaddress: remove 'label' compatibility with Linux-2.0 net aliases
1808f002 lib/fs: fix memory leak in get_task_name()
62c0700c uapi: update magic.h
c8d9d925 rdma: Fix the logic to print unsigned int.
a42dfaa4 Revert "rdma: Fix res_print_uint() and add res_print_u64()"
9d0badec rdma: Fix res_print_uint() and add res_print_u64()
86a1452b uapi: update to xfrm.h
09c6a3d2 bridge: Remove vlan listing from `bridge link`
e4fda259 bridge: Fix error string typo
cc143bda lnstat: fix strdup leak in -w argument parsing
90bbf861 iplink_can: print_usage: typo fix, add missing spaces
1b5c7414 dcb: Fix error reporting when accessing "dcb app"
a38d305d tc: fix duplicate fall-through
f8beda6e libnetlink: fix socket leak in rtnl_open_byproto()
7f70eb2a tc_util: Fix parsing action control with space and slash
29da83f8 iprule: Allow option dsfield in 'ip rule show'
07012a1f ss: use freecon() instead of free() when appropriate
03b4de0b man: Fix a typo in the flag documentation of ip address
924f6b4a dcb: app: Add missing "dcb app show dev X default-prio"
5c9571bc uapi: update kernel headers from 5.17-rc1
d542543b tc/action: print error to stderr
52370c61 mptcp: add id check for deleting address
c556f577 dcb: Rewrite array-formatting code to not cause warnings with Clang
0dc5da8e f_flower: fix checkpatch warnings
ffbcb246 netem: fix checkpatch warnings
8bced38a lib: fix ax25.h include for musl
e27bb8e5 uapi: add missing virtio headers
26ff0afa uapi: add missing rose and ax25 files
eb4206ec q_cake: allow changing to diffserv3
db530529 iplink_can: add ctrlmode_{supported,_static} to the "--details --json" output
ac2e9148 Update kernel headers
bb4cc9cc rdma: Don't allocate sparse array
b8767168 rdma: Limit copy data by the destination size
167e33f3 vdpa: Enable user to set mtu of the vdpa device
384938f9 vdpa: Enable user to set mac address of vdpa device
a311f0c4 vdpa: Enable user to query vdpa device config layout
9d8882d5 vdpa: Update kernel headers
5cb7ec0c Update kernel headers and import virtio_net
26113360 mptcp: add support for changing the backup flag
4b301b87 tc: Add support for ce_threshold_value/mask in fq_codel
99d09ee9 bond: add arp_missed_max option
432cb06b mptcp: add support for fullmesh flag
2d777dfe Update kernel headers
a21458fc vdpa: Remove duplicate vdpa UAPI header file
Signed-off-by: Nick Hainke <vincent@systemli.org>
Beeline SmartBox TURBO is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 2 buttons (Reset & WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (admin:admin)
2. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
3. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
4. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
5. Connect to the router using SSH shell (SuperUser:SNxxxxxxxxxx, where
SNxxxxxxxxxx is the serial number from the backplate label)
6. Run in SSH shell:
sh
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface (admin:admin)
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
1. Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:54 |
| WAN | label + 1 | *:55 |
| 2g | label + 4 | *:58 |
| 5g | label + 5 | *:59 |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Co-developed-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Add support for the TP-Link SG2008P switch. This is an RTL8380 based
switch with 802.3af one the first four ports.
Specifications:
---------------
* SoC: Realtek RTL8380M
* Flash: 32 MiB SPI flash (Vendor varies)
* RAM: 256 MiB (Vendor varies)
* Ethernet: 8x 10/100/1000 Mbps with PoE on 4 ports
* Buttons: 1x "Reset" button on front panel
* Power: 53.5V DC barrel jack
* UART: 1x serial header, unpopulated
* PoE: 1x TI TPS23861 I2C PoE controller
Works:
------
- (8) RJ-45 ethernet ports
- Switch functions
- System LED
Not yet enabled:
----------------
- Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
- PoE, Link/Act, PoE max and System LEDs
Install via web interface:
-------------------------
Not supported at this time.
Install via serial console/tftp:
--------------------------------
The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.
The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWRT:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U7)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as sson as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWRT.
Blind install via tftp:
-----------------------
This method works when it's not feasible to install a serial header.
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
3. Watch network traffic (tcpdump or wireshark works)
4. Power on the device.
5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U7)
6. When 192.168.0.30 makes tftp requests, release pin 16
7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add patch to skip bad blocks when reading from SPI-NAND. This is needed
in case erase block(s) early in the flash inside the FIP area are bad
and hence need to be skipped in order to be able to boot on such damaged
chips.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The command 'opkg search /etc/config/fstab' does not return a package
name for this config file. In order to know to which package this config
file belongs to, a 'conffiles' entry was made for this file to package
'block-mount'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
While kmod-input-core was previously indirectly selected by
kmod-input-polldev, this is now only the case on Linux 5.10.
Select kmod-input-core as dependency independently of the kernel
version to fix build error:
Package kmod-input-gpio-keys-polled is missing dependencies for the following libraries:
input-core.ko
Fixes: 54878fbbdd ("kernel: kmod-input-polldev: Depend on kernel 5.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import a3ba6adb70 arm: dts: mt7622: remove default pinctrl of uart0
and apply also to locally added boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for randomly generating a MAC address for a wifi-iface
instance by setting `macaddr` to `random`
When set to `random`, a new locally administered unicast MAC address
is generated and assigned to the iface everytime it is (re-)configured
Signed-off-by: Manas Sambhus <manas.sambhus+github@gmail.com>
The input-polldev.ko kernel module was removed from kernel 5.11. The
normal input implementation now supports polling.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sps30.ko driver was split into a main sps30.ko driver and a
sps30_i2c.ko driver for the I2C interface with kernel 5.14. Add the
sps30_i2c.ko module to the package too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The isdn4linux drivers and subsystem was removed in kernel 5.3, remove
the kernel package also from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The rtc-pt7c4338.ko was never upstream under this name, the driver was
removed from OpenWrt some years ago, remove the kmod-rtc-pt7c4338
package too.
Fixes: 74d00a8c38 ("kernel: split patches folder up into backport, pending and hack folders")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the kmod-wwan package. This provides the generic wwan driver
core which is needed for some existing packages.
Currently the drivers/net/wwan/wwan.ko driver is compiled into the
kernel when one of the wwan module is activated, better build it as a
kernel module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ulog iptables target was removed with kernel 3.17, remove the kernel
and also the iptables package in OpenWrt too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nft NAT packages for IPv4 and IPv6 were merged into the common
packages with kernel 5.1. The kmod-nft-nat6 package was empty in our
build, remove it.
Multiple kernel configuration options were also removed, remove them
from our generic kernel configuration too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The w1_ds2760.ko driver was merged into the ds2760_battery.ko driver.
The driver was removed and this package was never build any more.
This happened with kernel 4.19.
Remove this unused package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The R8712U driver depends on cfg80211. cfg80211 is provided by mac80211
backports, we can not build any in kernel drivers which depend on
cfg80211 which is an out of tree module in OpenWrt.
The cfg80211 dependency was added with kernel 5.9.
We could add rtl8192su to backports and build it from there.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The malta target does not compile CONFIG_OF_MDIO into the kernel. On
malta the kmod-mdio-devres package depends on kmod-of-mdio.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_CACHEFILES configuration option makes the kernel build
cachefiles.ko, also package it. Build CONFIG_CACHEFILES as module and do
not try to build it into the kernel. This did not work because it
depended on CONFIG_FSCACHE which was already build as module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_NLS_CODEPAGE_932 Config option builds the nls_cp932.ko and
the nls_euc-jp.ko kernel module, package both of them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add dwc2_pci kernel module into own kernel package.
The dwc2_pci.ko kernel module was always build when kmod-usb-dwc2
was selected, but it was not packaged.
Add the missing kmod-usb-phy-nop dependency to the kmod-usb-dwc2-pci
package too. The CONFIG_USB_DWC2_PLATFORM option is already gone for
some time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ar8xxx.ko kernel module uses the devm_mdiobus_alloc() function
provided by kmod-mdio-devres, add the missing dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Musl libc does not support the non-POSIX "%F" format for strptime() so
replace all occurrences of it with an equivalent "%Y-%m-%d" format.
Fixes: #10419
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The curl developers found test case that crashed in their testing when
using zlib patched against CVE-2022-37434, same patch we've backported
in commit 7df6795d4c ("zlib: backport fix for heap-based buffer
over-read (CVE-2022-37434)"). So we need to backport following patch in
order to fix issue introduced in that previous CVE-2022-37434 fix.
References: https://github.com/curl/curl/issues/9271
Fixes: 7df6795d4c ("zlib: backport fix for heap-based buffer over-read (CVE-2022-37434)")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Musl libc does not support the non-POSIX "%F" format for strptime() so
replace all occurrences of it with an equivalent "%Y-%m-%d" format.
Fixes: #10419
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The soversion of the shipped libjansson.so library didn't change, so the
ABI version change is unwarranted and leads to opkg file clashes.
Also stop shipping an unversioned library symlink while we're at it as
it only needed at compile/link time and leading to file level clashes
between packages on future ABI bumps.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Both of these packages depend on CONFIG_WWAN
in the kernel.
Also fix the missing "wwan" subfolder in the path.
This fixes the missing devices in /dev after booting an MHI capable modem.
Fixes: 2519190fec ("kernel: package mhi wwan ctrl driver")
Fixes: 6af46796fa ("kernel: package mhi mbim driver")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Backports upstream fix from 5.19
lockdep complains use of uninitialized spinlock at ieee80211_do_stop() [1],
for commit f856373e2f31ffd3 ("wifi: mac80211: do not wake queues on a vif
that is being stopped") guards clear_bit() using fq.lock even before
fq_init() from ieee80211_txq_setup_flows() initializes this spinlock.
According to discussion [2], Toke was not happy with expanding usage of
fq.lock. Since __ieee80211_wake_txqs() is called under RCU read lock, we
can instead use synchronize_rcu() for flushing ieee80211_wake_txqs().
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
libzstd from the packages feed gets picked up. Add patch adding
NO_LIBZSTD option like in perf and enable it.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This extracts kmod-sched-act-police to allow using it without adding all
the packages from the big kmod-sched package.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Add the ipset/ip_set_hash_ipmac.ko file. The CONFIG_IP_SET_HASH_IPMAC
KConfig option is already set by the package.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This adds the act_sample.ko and psample.ko kernel module which allows
traffic sampling.
Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Extract the kmod-sched-prio and kmod-sched-red kernel modules from the
big kmod-sched package. This allows adding the two kernel modules to
OpenWrt without adding the kmod-sched and all its depdnecy.
Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This puts the kmod-sched packages into an alphabetical order.
I kept the kmod-sched-core at the top as this is the main package.
No changes other than reordering were done.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Change SCHED_MODULES_EXTRA to an explicit list of modules
instead of taking everything that is not filtered out.
This removes the need of updating the filter each time an extra
sch_*, act_* or similar is added with an own kmod definition.
Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
The sch_fq_codel.ko and the sch_fifo.ko are always compiled into the
kernel, they are activated in the generic kernel configuration. There is
no need to activate the build of these kernel modules in the kmod-sched*
packages.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
The ZyXEL LTE3301-PLUS is an 4G indoor CPE with 2 external LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7615E
- Switch: 4 LAN ports (Gigabit)
- LTE: Quectel EG506 connected by USB3 to SoC
- SIM: 1 micro-SIM slot
- USB: USB3 port
- Buttons: Reset, WPS
- LEDs: Multicolour power, internet, LTE, signal, Wifi, USB
- Power: 12V, 1.5A
The device is built as an indoor ethernet to LTE bridge or router with
Wifi.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
MAC assignment:
lan: 98:0d:67:ee:85:54 (base, on the device back)
wlan: 98:0d:67:ee:85:55
Installation from web GUI:
- Log in as "admin" on http://192.168.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- format ubi device: ubiformat /dev/mtd6
- attach ubi device: ubiattach -m6
- create rootfs volume: ubimkvol /dev/ubi0 -n0 -N rootfs -s 1MiB
- rootfs_data volume: ubimkvol /dev/ubi0 -n1 -N rootfs_data -s 1MiB
- run sysupgrade with sysupgrade image
For more details about flashing see
commit 2449a63208 ("ramips: mt7621: Add support for ZyXEL NR7101").
Please note that this commit is needed:
firmware-utils: add marcant changes for ZyXEL NBG6716 and LTE3301-PLUS
Signed-off-by: André Valentin <avalentin@marcant.net>
The Sophos AP15 seems to be very close to Sophos AP55/AP100.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15:
- Green and yellow LED
- 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
- No buttons
- No piezo beeper
- No 5.8GHz
Flashing instructions:
- Derived from UART method described in referenced commit, methods
described there should work too.
- Set up a TFTP server; IP address has to be 192.168.99.8/24
- Copy the firmware (initramfs-kernel) to your TFTP server directory
renaming it to e.g. boot.bin
- Open AP's enclosure and locate UART header (there is a video online)
- Terminal connection parameters are 115200 8/N/1
- Connect TFTP server and AP via ethernet
- Power up AP and cancel autoboot when prompted
- Prompt shows 'ath> '
- Commands used to boot:
ath> tftpboot 0x81000000 boot.bin
ath> bootm 0x81000000
- Device should boot OpenWRT
- IP address after boot is 192.168.1.1/24
- Connect to device via browser
- Permanently flash using the web ui (flashing sysupgrade image)
- (BTW: the AP55 images seem to work too, only LEDs are not working)
Testing done:
- To be honest: Currently not so much testing done.
- Flashed onto two devices
- Devices are booting
- MAC addresses are correct
- LEDs are working
- Scanning for WLANs is working
Big thanks to all the people working on this great project!
(Sorry about my english, it is not my native language)
Signed-off-by: Manuel Niekamp <m.niekamp@richter-leiterplatten.de>
Remove outdated patches:
- 100-musl.patch
- 110-mac80211_tracepoint.patch
Trace-cmd now uses libtracefs and livtraceevent as libraries.
The plugins moved to libtraceevent.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
debuginfod: Support -C option for connection thread pooling.
debuginfod-client: Negative cache file are now zero sized instead of
no-permission files.
addr2line: The -A, --absolute option, which shows file names including
the full compilation directory is now the default. To get the
old behavior use the new option --relative.
readelf, elflint: Recognize FDO Packaging Metadata ELF notes
libdw, debuginfo-client: Load libcurl lazily only when files need to
be fetched remotely. libcurl is now never
loaded when DEBUGINFOD_URLS is unset. And when
DEBUGINFOD_URLS is set, libcurl is only loaded
when the debuginfod_begin function is called.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The heartbeat trigger has the option to be inverted, however
openwrt/uci/luci have no way to set this.
This patch adds this support.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
zlib through 1.2.12 has a heap-based buffer over-read or buffer overflow
in inflate in inflate.c via a large gzip header extra field. NOTE: only
applications that call inflateGetHeader are affected. Some common
applications bundle the affected zlib source code but may be unable to
call inflateGetHeader.
Fixes: CVE-2022-37434
References: https://github.com/ivd38/zlib_overflow
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This change was included in the original pull request but later omitted
for some reason:
https://github.com/openwrt/openwrt/pull/4936
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Config partition contains uboot env for the first 0x20000 bytes.
The rest of the partition contains other data including the device MAC
address and the password printed on the label.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
"The MCP2221 is a USB-to-UART/I2C serial converter which enables
USB connectivity in applications that have a UART and I2C interfaces."
<https://www.microchip.com/en-us/product/MCP2221>
Signed-off-by: Leo Soares <leo@hyper.ag>
(replaced GPIOLIB KConfig with @GPIO_SUPPORT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
all other drivers depend on @GPIO_SUPPORT rather than
forcing CONFIG_GPIOLIB=y.
(I wonder what would happen if someone decides to try
UML with USBIP?)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The re-transmit counters can overflow the 32 bit representation resulting
in negative values being displayed. Background being that the numbers are
treated at some point as signed INT rather than unsigned INT.
Change the counters from 32 bit to 64 bit, should provide sufficient room
to avoid any overflow. Not the nicest solution but it works
Fixes: #10077
Signed-off-by: Roland Barenbrug <roland@treslong.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This fixes the libmnl build on macOS, which ships with an outdated bash
at /bin/bash. During the OpenWrt build, a modern host bash is built and
made available at staging_dir/host/bin/bash, which is present before
/bin/bash in the build's PATH.
This is similar to 8f7ce3aa6d, presently appearing at
package/kernel/mac80211/patches/build/001-fix_build.patch.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.
Specifications:
SOC: MT7621 + MT7915
ROM: 128 MiB
RAM: 256 MiB
LED: status *2
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP server IP: 192.168.124.99
MAC Address:
use address(sample 1) address(sample 2) source
label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr
lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1
wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label
WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode)
WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode)
WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7
WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7
Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.
TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
|GND|TX|RX|VCC|
1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
and open a TTL session, enter "reboot", then enter "Y" to confirm.
Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
# tftp 0x80010000 192.168.124.99:initramfs.bin
# bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
partitions if we want to back to stock firmwre due to official
website does not provide download link.
# dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
# dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
# fw_setenv bootargs
# fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
partitions that we backed up in step 4.
# mtd write /tmp/u-boot-env.bin u-boot-env
# mtd write /tmp/firmware.bin firmware
Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
