The commit [1] added support for Ubiquiti PowerBeam M (XW), tested
on the PBE-M5-400. But, it turns out the PBE-M2-400 has a different
ethernet configuration, so make the support specific to the m5 version
in anticipation of adding specific support for the m2 in a separate
commit.
[1] 12eb5b2384 ("ath79: add support for Ubiquiti PowerBeam M (XW)")
Signed-off-by: Russell Senior <russell@personaltelco.net>
[fix model name in DTS, format commit reference in commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Due to use of a script when migrating from mtd-mac-address, a few
of the definitions are redundant in DTSI and DTS files. Remove
those and consolidate the definitions in parent DTSI files in a
few cases.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since the nvmem-based approach for retrieving MAC addresses
appears to depend on the addresses being set up after the
partitions, it is no longer possible to keep the MAC address
setup in shared DTSI files while the partitions itself are
set up in DTS files for the individual devices.
In ath79 the firmware partition is typically located somewhere
"in the middle" of the partition table. Thus, it's not trivial
to share the partitions containing MAC address information in
a common DTSI (like we did in some cases on ramips).
In this commit, MAC address setup is thus moved to the relevant
partitions, and in most cases needs to be duplicated. While
the duplication is not really nice, it eventually provides a
cleaner and more tidy setup, making the DTS(I) file
fragmentation a bit more logical. This should also help
with adding new devices, as information is distributed across
less locations.
For consistency, this commit also moves the mtd-cal-data property
"down" together with the MAC address setup, so it's not based
on a partition before the latter is defined either. (This is
only done for those files touched due to nvmem conversion.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The GL-X300B is a industrial 4G LTE router based on the Qualcomm
QCA9531 SoC.
Specifications:
- Qualcomm QCA9531 @ 650 MHz
- 128 MB of RAM
- 16 MB of SPI NOR FLASH
- 2x 10/100 Mbps Ethernet
- 2.4GHz 802.11b/g/n
- 1x USB 2.0 (vbus driven by GPIO)
- 4x LED, driven by GPIO
- 1x button (reset)
- 1x mini pci-e slot (vcc driven by GPIO)
- RS-485 Serial Port (untested)
Flash instructions:
This firmware can be flashed using either sysupgrade from the GL.iNet
firmware or the recovery console as follows:
- Press and hold the reset button
- Connect power to the router, wait five seconds
- Manually configure 192.168.1.2/24 on your computer, connect to
192.168.1.1
- Upload the firmware image using the web interface
RS-485 serial port is untested and may depend on the following commit in
the GL.iNet repo:
202e83a32a
MAC addresses as verified by OEM firmware:
vendor OpenWrt address
WAN eth0 label
LAN eth1 label + 1
2g phy0 label + 2
The label MAC address was found in the art partition at 0x0
Based on vendor commit:
16c5708b20
Signed-off-by: John Marrett <johnf@zioncluster.ca>
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The LEDs for LAN1 and LAN3 were swapped. Link on port 1 would illuminate
the LED on port 3 and vice versa.
Signed-off-by: David Bauer <mail@david-bauer.net>
Without explicit configuration of these pins the ethernet as well as
status LED of the device do not work correctly.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
* QCA9531, 16 MiB flash (Winbond W25Q128JVSQ), 128 MiB RAM
* 802.11n 2T2R (external antennas)
* QCA9887, 802.11ac 1T1R (connected with diplexer to one of the antennas)
* 3x 10/100 LAN, 1x 10/100 WAN
* UART header with pinout printed on PCB
Installation:
* The device comes with a bootloader installed only
* The bootloader offers DHCP and is reachable at http://10.123.123.1
* Accept the agreement and flash sysupgrade.bin
* Use Firefox if flashing does not work
TFTP recovery with static IP:
* Rename sysupgrade.bin to jt-or750i_firmware.bin
* Offer it via TFTP server at 192.168.0.66
* Keep the reset button pressed for 4 seconds after connecting power
TFTP recovery with dynamic IP:
* Rename sysupgrade.bin to jt-or750i_firmware.bin
* Offer it via TFTP server with a DHCP server running at the same address
* Keep the reset button pressed for 6 seconds after connecting power
Co-authored-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
A missing quote in target/linux/ath79/patches-5.x/920-mikrotik-rb4xx.patch
produces:
...
scripts/kconfig/conf --syncconfig Kconfig
drivers/mfd/Kconfig:2016:warning: multi-line strings not supported
...
This patch adds missing closing quote, fixing the above warning.
Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.
This should make simplify the conversion of target to nvmem implementation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Looks like the symbol was forgotten for 5.4
Fixes: 820e660cd7 ("ath79: add NAND driver for MikroTik RB91xG series")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The MX25L12805D used on all ath79 OCEDO boards supports clock
speeds up to 50 MHz.
Thus, we can increase the maximum SPI frequency the flash chip is
controlled at to 50 MHz, increasing transfer speed.
Signed-off-by: David Bauer <mail@david-bauer.net>
The M25P80 used on the Siemens WS-AP3610 supports clock speeds up to 54
MHz. Thus, we can safely increase the maximum SPI frequency the flash
chip is controlled at to 50 MHz, increasing transfer speed.
Signed-off-by: David Bauer <mail@david-bauer.net>
Device specifications
* SoC: QCA9563 @ 775MHz (MIPS 74Kc)
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (EN25QH128)
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9988): a/n/ac, 4x4 MU-MIMO
* IoT Wireless 2.4GHz (QCA6006): currently unusable
* Ethernet (AR8327): 3 LAN × 1GbE, 1 WAN × 1GbE
* LEDs: Internet (blue/orange), System (blue/orange)
* Buttons: Reset
* UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
* Power: 12VDC, 1,5A
MAC addresses map (like in OEM firmware)
art@0x0 88:C3:97:*:57 wan/label
art@0x1002 88:C3:97:*:2D lan/wlan2g
art@0x5006 88:C3:97:*:2C wlan5g
Obtain SSH Access
1. Download and flash the firmware version 1.3.8 (China).
2. Login to the router web interface and get the value of `stok=` from the
URL
3. Open a new tab and go to the following URL (replace <STOK> with the stok
value gained above; line breaks are only for easier handling, please put
together all four lines into a single URL without any spaces):
http://192.168.31.1/cgi-bin/luci/;stok=<STOK>/api/misystem/set_config_iotdev
?bssid=any&user_id=any&ssid=-h%0Anvram%20set%20ssh_en%3D1%0Anvram%20commit
%0Ased%20-i%20%27s%2Fchannel%3D.%2A%2Fchannel%3D%5C%5C%22debug%5C%5C%22%2F
g%27%20%2Fetc%2Finit.d%2Fdropbear%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A
4. Wait 30-60 seconds (this is the time required to generate keys for the
SSH server on the router).
Create Full Backup
1. Obtain SSH Access.
2. Create backup of all flash (on router):
dd if=/dev/mtd0 of=/tmp/ALL.backup
3. Copy backup to PC (on PC):
scp root@192.168.31.1:/tmp/ALL.backup ./
Tip: backup of the original firmware, taken three times, increases the
chances of recovery :)
Calculate The Password
* Locally using shell (replace "12345/E0QM98765" with your router's serial
number):
On Linux
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5sum - | head -c8 && echo
On macOS
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5 | head -c8
* Locally using python script (replace "12345/E0QM98765" with your
router's serial number):
wget https://raw.githubusercontent.com/eisaev/ax3600-files/master/scripts/calc_passwd.py
python3.7 -c 'from calc_passwd import calc_passwd; print(calc_passwd("12345/E0QM98765"))'
* Online
https://www.oxygen7.cn/miwifi/
Debricking (lite)
If you have a healthy bootloader, you can use recovery via TFTP using
programs like TinyPXE on Windows or dnsmasq on Linux. To switch the router
to TFTP recovery mode, hold down the reset button, connect the power
supply, and release the button after about 10 seconds. The router must be
connected directly to the PC via the LAN port.
Debricking
You will need a full dump of your flash, a CH341 programmer, and a clip
for in-circuit programming.
Install OpenWRT
1. Obtain SSH Access.
2. Create script (on router):
echo '#!/bin/sh' > /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo '. /bin/boardupgrade.sh' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo 'board_prepare_upgrade' >> /tmp/flash_fw.sh
echo 'mtd erase rootfs_data' >> /tmp/flash_fw.sh
echo 'mtd write /tmp/openwrt.bin firmware' >> /tmp/flash_fw.sh
echo 'sleep 3' >> /tmp/flash_fw.sh
echo 'reboot' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
chmod +x /tmp/flash_fw.sh
3. Copy `openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin`
to the router (on PC):
scp openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin \
root@192.168.31.1:/tmp/openwrt.bin
4. Flash OpenWRT (on router):
/bin/ash /tmp/flash_fw.sh &
5. SSH connection will be interrupted - this is normal.
6. Wait for the indicator to turn blue.
Signed-off-by: Evgeniy Isaev <isaev.evgeniy@gmail.com>
[improve commit message formatting slightly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SOC: Qualcomm Atheros TP9343 (750 MHz)
Flash: 8 Mb (GigaDevice GD25Q64CSIG)
RAM: 64 Mb (Zentel A3R12E40DBF-8E)
Serial: yes, 4-pin header
Wlan: Qualcomm Atheros TP9343, antenna: MIM0 3x3:3 RP-SMA
3 x 2.4GHz power amp module Skyworks (SiGe) SE2576L
Ethernet: Qualcomm Atheros TP9343
Lan speed: 100M ports: 4
Lan speed: 100M ports: 1
Other info: same case, ram and flash that TP-Link TL-WR841HP,
different SOC
https://forum.openwrt.org/t/adding-device-support-tp-link-wr941hp/
Label MAC addresses based on vendor firmware:
LAN *:ee label
WAN *:ef label +1
WLAN *:ee label
The label MAC address found in "config" partition at 0x8
Flash instruction:
Upload the generated factory firmware on web interface.
Signed-off-by: Diogenes Rengo <rengocbx250@gmail.com>
[remove various whitespace issues, squash commits, use short 0x0]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the Ubiquiti PowerBeam M (XW), e.g. PBE-M5-400,
a 802.11n wireless with a feed+dish form factor. This device was previously
supported by the ar71xx loco-m-xw firmware.
Specifications:
- Atheros AR9342 SoC
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in
- Power and LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1)
Flashing via stock GUI:
- Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see
https://openwrt.org/toh/ubiquiti/powerbeam installation instructions)
- Upload the factory image via AirOS web GUI.
Flashing via TFTP:
- Use a pointy tool (e.g., unbent paperclip) to keep the
reset button pressed.
- Power on the device (keep reset button pressed).
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button.
- The device starts a TFTP server at 192.168.1.20.
- Set a static IP on the computer (e.g., 192.168.1.21/24).
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbeam-m-xw-squashfs-factory.bin
WARNING: so far, no non-destructive method has been discovered for
opening the enclosure to reach the serial console. Internal photos
are available here: https://fcc.io/SWX-NBM5HP
Signed-off-by: Russell Senior <russell@personaltelco.net>
The ar71xx GPIO driver only uses 0x24 registers, all following GPIO
registers are using to control pinmux functions, which are not handles
by the GPIO driver but the generic Linux pinctrl driver.
For some SoC conflicting address ranges were defined for these (AR7240 &
AR9330).
Resolve these cases and align the address space of the GPIO controller
between all SoCs, as the used address space of the driver is identical
for all these.
Signed-off-by: David Bauer <mail@david-bauer.net>
Analysis done by Denis Kalashnikov:
It seems that some ROS versions on some routerboard models have this bug:
after silence boot (no output to uart, no beeps) beeper clicks when wireless traffic is.
https://forum.mikrotik.com/viewtopic.php?f=3&t=92269https://forum.mikrotik.com/viewtopic.php?t=63399
From these links:
1)
Hello, I have RB951G-2HnD and I noticed strange thing
when I loaded the device with some wireless traffic it
produced strange sound - like hissing, fizzing etc.
2)
Same problem still on 6.33, with silent boot enabled
I hear buzzing noise on wireless load.
3)
The sound is fixed in v5.19, it was a bug that caused beeper to make clicks.
It also got fixed in RouterOS:
* What's new in 5.19 (2012-Jul-16 10:51):
fix ticking sound on RB411UAHL;
* What's new in 6.38.3 (2017-Feb-07 09:52):
rb3011 - fixed noise from buzzer after silent boot;
I've checked with an oscilloscope that:
* When on the ssr beeper pin is 0,
on the beeper itself is 1 (~5V),
and when on the ssr beeper pin is 1,
on the beeper is 0
The beeper doesn't consume power,
so 1 should be a default/idle value for the ssr beeper pin).
* When there is wireless traffic (ping packets)
in the background and the beeper clicks, I see
pulses on the beeper itself,
but no pulses on the ssr beeper pin (Q5 pin of 74hc595).
When I manually toggle the ssr beeper pin I see pulses on both.
So, it is likely that the phantom beeper clicks are caused by the EMI.
Suggested-by: Denis Kalashnikov <denis281089@gmail.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This commit adds support for the Teltonika RUT230 v1, a Atheros AR9331
based router with a Quectel UC20 UMTS modem.
Hardware
--------
Atheros AR9331
16 MB SPI-NOR XTX XT25F128B
64M DDR2 memory
Atheros AR9331 1T1R 802.11bgn Wireless
Boootloader: pepe2k U-Boot mod
Hardware-Revision
-----------------
There are two board revisions of the RUT230, a v0 and v1.
A HW version is silkscreened on the top of the PCBs front side as well
as shown in the Teltonika UI. However, this looks to be a different
identifier, as the GPl dump shows this silkscreened / UI shown version
are internally treated identically.
Th following mapping has been obtained from the latest GPl dump.
HW Ver 01 - 04 --> v0
HW Ver > 05 --> v1
My board was a HW Ver 09 and is treated as a v1.
Installation
------------
While attaching power, hold down the reset button and release it after
the signal LEDs flashed 3 times.
Attach your Computer with the devices LAN port and assign yourself the
IPv4 address 192.168.1.10/24. Open a web browser, navigate to
192.168.1.1. Upload the OpenWrt factory image.
The device will install OpenWrt and automatically reboots afterwards.
You can use the smae procedure with the stock firmware to return back to
the vendor firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
The beeper is currently not fully functional and has also
been removed from DTS.
Also remove the dependency for the gpio-beeper module.
Fixes: 695a1cd53c ("ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Without this patch we have to manually bring up the CPU interface in
failsafe mode.
This was backported from kernel 5.12.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Currently, the option to disable subpage writing is only set
when a HW ECC engine is used.
Some boards lack a HW ECC engine and use software for that.
In this case, this NAND option does not get set when the NAND chip
does not support it, resulting in mounting errors.
Move the setting of this option to a generic init location so it
gets set for all types where required.
While at it, also OR the option instead of just setting it
so we don't overwrite potential flags being set somewhere else.
Before:
[ 1.681273] UBI: auto-attach mtd2
[ 1.684669] ubi0: attaching mtd2
[ 1.688877] ubi0 error: validate_ec_hdr: bad VID header offset 2048, expected 512
[ 1.696469] ubi0 error: validate_ec_hdr: bad EC header
[ 1.701712] Erase counter header dump:
[ 1.705512] magic 0x55424923
[ 1.709322] version 1
[ 1.712330] ec 1
[ 1.715331] vid_hdr_offset 2048
[ 1.718610] data_offset 4096
[ 1.721880] image_seq 1462320675
[ 1.725680] hdr_crc 0x12255a15
After:
1.680917] UBI: auto-attach mtd2
[ 1.684308] ubi0: attaching mtd2
[ 2.954504] random: crng init done
[ 3.142813] ubi0: scanning is finished
[ 3.163455] ubi0: attached mtd2 (name "ubi", size 124 MiB)
[ 3.169069] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.176037] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.182942] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.190013] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0
[ 3.196102] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 3.203434] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1462320675
[ 3.212700] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20
[ 3.222124] ubi0: background thread "ubi_bgt0d" started, PID 317
[ 3.230246] block ubiblock0_1: created from ubi0:1(rootfs)
[ 3.235819] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 3.256830] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This board has been supported in the ar71xx.
Links:
* https://mikrotik.com/product/RB912UAG-2HPnD
* https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb912uag-2hpnd
This also supports the 5GHz flavour of the board.
Hardware:
* SoC: Atheros AR9342,
* RAM: DDR 64MB,
* SPI NOR: 64KB,
* NAND: 128MB,
* Ethernet: x1 10/100/1000 port with passive POE in,
* Wi-Fi: 802.11 b/g/n,
* PCIe,
* USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A
port -- both can be used for LTE modem, but only one can be
used at any time.
* LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED,
Ethernet phy LED,
* Button,
* Beeper.
Not working:
* Button: it shares gpio line 15 with NAND ALE and NAND IO7,
and current drivers doesn't easily support this configuration,
* Beeper: it is connected to bit 5 of a serial shift register
(tested with sysfs led trigger timer). But kmod-gpio-beeper
doesn't work -- we left this as is for now.
Flashing:
* Use the RouterBOARD Reset button to enable TFTP netboot,
boot kernel and initramfs and then perform sysupgrade.
* From ar71xx OpenWrt firmware run:
$ sysupgrade -F /tmp/<sysupgrade.bin>
For more info see: https://openwrt.org/toh/mikrotik/common.
Co-Developed-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Main part is copied from ar71xx original driver rb91x_nand
written by Gabor Juhos <juhosg@openwrt.org>.
What is done:
* Support of kernel 5.4 and 5.10,
* DTS support,
* New gpio API (gpiod_*) support.
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
This is a slighty modified version of ar71xx gpio-latch driver
written by Gabor Juhos <juhosg@openwrt.org>.
Changes:
* DTS support,
* New gpio API (gpiod_*).
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Specifications:
- QCA9533 SoC, 8 MB nor flash, 64 MB DDR2 RAM
- 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps
- 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100
- 1x WAN, LAN, Wifi, PWR, WPS, RE Leds
- Reset, Wifi on/off, WPS, RE buttons
- Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1
Label MAC addresses based on vendor firmware:
LAN *:ea label
WAN *:eb label +1
2.4 GHz *:ea label
The label MAC address in found in u-boot 0x1fc00
Installation:
Upload openwrt-ath79-generic-tplink_tl-wr841hp-v3-squashfs-factory.bin
from stock firmware webgui.
Maybe we need rename to shorten file name due to stock webgui error.
Revert back to stock firmware instructions:
- set your PC to static IP address 192.168.0.66 netmask 255.255.255.0
- download stock firmware from Tp-link website
- put it in the root directory of tftp server software
- rename it to wr841hpv3_tp_recovery.bin
- power on while pressing Reset button until any Led is lighting up
- wait for the router to reboot. done
Forum support topic:
https://forum.openwrt.org/t/support-for-tp-link-tl-wr841hp-v3-router
Signed-off-by: Andy Lee <congquynh284@yahoo.com>
[rebase and squash]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces the register bits for RGMII delay on the MAC side in favor
of having the RGMII delay on the PHY side by setting the phy-mode
property to rgmii-id (RGMII internal delay), which is supported by the
at803x driver. Speed 1000 is fixed as a result, so now all ethernet
speeds function.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Michael Pratt <mcpratt@pm.me>
NEC Aterm WF1200CR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9561.
Specification:
- SoC : Qualcomm Atheros QCA9561
- RAM : DDR2 128 MiB (W971GG6SB-25)
- Flash : SPI-NOR 8 MiB (MX25L6433FM2I-08G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : QCA9561 (SoC)
- 5 GHz : QCA9888
- Ethernet : 2x 10/100 Mbps
- Switch : QCA9561 (SoC)
- LEDs/Keys : 8x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- JP1: Vcc, GND, NC, TX, RX from "JP1" marking
- 115200n8
- Power : 12 VDC, 0.9 A
Flash instruction using factory image (stock: < v1.3.2):
1. Boot WF1200CR normally with "Router" mode
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button to
perform firmware update
4. Wait ~150 seconds to complete flashing
Alternate flash instruction using initramfs image (stock: >= v1.3.2):
1. Prepare the TFTP server with the IP address 192.168.1.10 and place
the OpenWrt initramfs image to the TFTP directory with the name
"0101A8C0.img"
2. Connect serial console to WF1200CR
3. Boot WF1200CR and interrupt with any key after the message
"Hit any key to stop autoboot: 2", the U-Boot starts telnetd after
the message "starting telnetd server from server 192.168.1.1"
4. login the telnet (address: 192.168.1.1)
5. Perform the following commands to modify "bootcmd" variable
temporary and check the value
(to ignore the limitation of available commands, "tp; " command at
the first is required as dummy, and the output of "printenv" is
printed on the serial console)
tp; set bootcmd 'set autostart yes; tftpboot'
tp; printenv
6. Save the modified variable with the following command and reset
device
tp; saveenv
tp; reset
7. The U-Boot downloads initramfs image from TFTP server and boots it
8. On initramfs image, download the sysupgrade image to the device and
perform the following commands to erase stock firmware and sysupgrade
mtd erase firmware
sysupgrade <sysupgrade image>
9. After the rebooting by completion of sysupgrade, start U-Boot telnetd
and login with the same way above (3, 4)
10. Perform the following commands to reset "bootcmd" variable to the
default and reset the device
tp; run seattle
tp; reset
(the contents of "seattle":
setenv bootcmd 'bootm 0x9f070040' && saveenv)
11. Wait booting-up the device
Known issues:
- the following 6x LEDs are connected to the gpio controller on QCA9888
chip and the implementation of control via the controller is missing in
ath10k/ath10k-ct
- "ACTIVE" (Red/Green)
- "2.4GHz" (Red/Green)
- "5GHz" (Red/Green)
Note:
- after the version v1.3.2 of stock firmware, "offline update" by
uploading image by user is deleted and the factory image cannot be
used
- the U-Boot on WF1200CR doesn't configure the port-side LEDs on WAN/LAN
and the configuration is required on OpenWrt
- gpio-hog: set the direction of GPIO 14(WAN)/19(LAN) to output
- pinmux: set GPIO 14/19 as switch-controlled LEDs
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch adds support for the Devolo dLAN pro 1200+ WiFi ac.
This device is a plc wifi AC2400 router/extender with 2 Ethernet ports,
has a QCA7500 PLC and uses the HomePlug AV2 standard.
Other than the PLC the hardware is identical to the Devolo Magic 2 WIFI.
Therefore it uses the same dts, which was moved to a dtsi to be included
by both boards.
This is a board that was previously included in the ar71xx tree.
Hardware:
SoC: AR9344
CPU: 560 MHz
Flash: 16 MiB (W25Q128JVSIQ)
RAM: 128 MiB DDR2
Ethernet: 2xLAN 10/100/1000
PLC: QCA75000 (Qualcomm HPAV2)
PLC Uplink: 1Gbps MIMO
PLC Link: RGMII 1Gbps (WAN)
WiFi: Atheros AR9340 2.4GHz 802.11bgn
Atheros AR9882-BR4A 5GHz 802.11ac
Switch: QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2
Button: 3x Buttons (Reset, wifi and plc)
LED: 3x Leds (wifi, plc white, plc red)
GPIO Switch: 11-PLC Pairing (Active Low)
13-PLC Enable
21-WLAN power
MACs Details verified with the stock firmware:
Radio1: 2.4 GHz &wmac *:4c Art location: 0x1002
Radio0: 5.0 GHz &pcie *:4d Art location: 0x5006
Ethernet ðernet *:4e = 2.4 GHz + 2
PLC uplink --- *:4f = 2.4 GHz + 3
Label MAC address is from PLC uplink
The Powerline (PLC) interface of the dLAN pro 1200+ WiFi ac requires 3rd
party firmware which is not available from standard OpenWrt package
feeds. There is a package feed on github which you must add to
OpenWrt buildroot so you can build a firmware image which supports the
plc interface.
See: https://github.com/0xFelix/dlan-openwrt (forked from Devolo and
added compatibility for OpenWrt 21.02)
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.100
2. Download the sysupgrade image and rename it to uploadfile
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Allow 1-2 minutes for the first boot.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
[add "plus" to compatible and device name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.
[*] As a funny side-fact, copy-pasting has led to almost all
hotplug.d files using the "+", while nearly all of the
02_network files are not using it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CPExxx and WBSxxx boards with AR9344 SOC
use the OKLI lzma kernel loader
with the offset of 3 blocks of length 4k (0x3000)
in order to have a fake "kernel" that cannot grow larger
than how it is defined in the now static OEM partition table.
Before recent changes to the mtdsplit driver,
the uImage parser for OKLI only supported images
that started exactly on an eraseblock boundary.
The mtdsplit parser for uImage now supports identifying images
with any magic number value
and at any offset from the eraseblock boundary
using DTS properties to define those values.
So, it is no longer necessary to use fixed sizes
for kernel and rootfs
Tested-by: Andrew Cameron <apcameron@softhome.net> [CPE510 v2]
Tested-by: Bernhard Geier <freifunk@geierb.de> [WBS210 v2]
Tested-by: Petrov <d7c48mWsPKx67w2@gmail.com> [CPE210 v1]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Specifications:
SoC: QCA9533
DRAM: 32Mb DDR1
Flash: 8/16Mb SPI-NOR
LAN: 4x 10/100Mbps via AR8229 switch (integrated into SoC)
on GMII
WAN: 1x 10/100Mbps via MII
WLAN: QCA9530
USB: 1x 2.0
UART: standard QCA UART header
JTAG: yes
Button: 1x WPS, 1x reset
LEDs: 8x LEDs
A version with 4Mb flash is also available, but due to lack of
enough space it's not supported.
As the original flash layout does not provide enough space for
the kernel (1472k), the firmware uses OKLI and concat flash to
overcome the limitation without changing the boot address of the
bootloaders.
Installation:
1. Original bootloader
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
available via TFTP
tftpboot 0x80060000 openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
Reboot the board.
2. pepe2k's u-boot_mod
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
available via TFTP, as "firmware.bin"
run fw_upg
Reboot the board.
For the 16M version of the board, please use
openwrt-ath79-generic-qca_ap143-16m-squashfs-factory.bin
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
[use fwconcatX names, drop redundant uart status, fix IMAGE_SIZE,
set up IMAGE/factory.bin without metadata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8031 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The patch was not applied to the v5.4 target, thus breaking Kernel 5.4
on devices with multiple flash chips attache to the SPI bus.
Fixes commit bd54e73954 ("ath79: set number of chipselect lines")
Signed-off-by: David Bauer <mail@david-bauer.net>
ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional
antenna. It is low cost and mostly available via Aliexpress, references can
be found at:
- https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383
- https://git.lsd.cat/g/openwrt-cpe46b
Specifications:
- Atheros AR9330
- 32MB of RAM
- 8MB of flash (SPI NOR)
- 1 * 2.4ghz integrated antenna
- 2 * 10/100/1000 ethernet ports (1 POE)
- 3 * Green LEDs controlled by the SoC
- 3 * Green LEDs controlled via GPIO
- 1 * Reset Button controlled via GPIO
- 1 * 4 pin serial header on the PCB
- Outdoor packaging
Flashing instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor
Telnet console is vulnerable to command injection and can be used to gain
a shell directly on the OEM OpenWrt distribution.
Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org>
[fix whitespaces, drop redundant uart status and serial0, drop
num-chipselects, drop 0x1002 MAC address for wmac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
COMFAST CF-E375AC is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
1) Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
2) TFTP
2.1) Set a tftp server on your machine with a fixed IP address of
192.168.1.10. A place the sysupgrade as firmware_auto.bin.
2.2) boot the device with an ethernet connection on fixed ip route
2.3) wait a few seconds and try to login via ssh
3) TFTP trough Bootloader
3.1) open the device case and get a uart connection working
3.2) stop the autoboot process and test connection with serverip
3.3) name the sysupgrade image firmware.bin and run firmware_upg
MAC addresses:
Though the OEM firmware has four adresses in the usual locations,
it appears that the assigned addresses are just incremented in a
different way:
interface address location
LAN: *:DC 0x0
WAN *:DD 0x1002
WLAN 2.4g *:E6 n/a (0x0 + 10)
WLAN 5g *:DE 0x6
unused *:DF 0x5006
The MAC address pointed at the label is the one assign to the LAN
interface.
Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com>
[add label-mac-device, remove redundant uart status, fix whitespace
issues, fix commit message wrapping, remove x bit on DTS file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes a small regression where the lzma-loader variable values
are being shared between boards that require different configurations.
If not set to "" globally, a device without these settings will just take
the last values another device has set before in the queue.
Fixes: 1b8bd17c2d ("ath79: lzma-loader: allow setting custom kernel magic")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[add detailed explanation to the commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. In most of the cases, I just saw warnings like this:
make: Entering directory '/home/.../package/gluon-status-page'
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
[...]
While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.
After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
ath79, lantiq, ipq40xx, ramips all use the OpenWrt-specific gpio-export
functionality. Consolidate the patch that adds it under hack-5.10 since
this logic is obviously not target-specific. For those who want to
disable it, unsetting CONFIG_GPIO_SYSFS symbol will disable this code.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
The kernel image is too big now and the build fails.
WARNING: Image file zyxel_nbg6716-kernel.bin is too big: 4205404 > 4194304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The spi-ath79 driver performs the chipselect by writing to dedicated
register in the SPI register block. So the GPIO numbers were not used.
Tested-on: Enterasys WS-AP3705i
Signed-off-by: David Bauer <mail@david-bauer.net>
All chipsets from AR7100 up to QCA9563 have three dedicated chipselect
lines for the integrated SPI controller. Remove the number of
chipselects from the platform data, as there is no need to manually set
this to a different value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the SPI_MASTER_GPIO_SS flag for the spi-ath79 driver. Otherwise,
the custom chipselect function is never called. This breaks hardware,
where the three dedicated chipselect lines are used instead of generic
GPIO pins.
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.
This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.
This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.
The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.
This increases the size of an uncompressed kernel by less than 1 KB.
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This CFI patch was accepted upstream for 5.13. Move it away from under
ath79 and place under backports to be removed in due time.
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93
Signed-off-by: John Audia <graysky@archlinux.us>
Since support for SFP on the MikroTik RouterBOARD 922UAGS-5HPacD was
added by 4387fe00cb, the MAC addresses for eth0 (Ethernet) and eth1
(SFP) were swapped. This patch fixes the 02_network script to assign MAC
addresses correctly, so they match the label and the vendor's OS.
Tested on a RouterBOARD 922UAGS-5HPacD board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Commit f724a583dc updated the nand-rb4xx driver to the 5.10 testing
kernel, but forgot to add the new kernel config symbol it introduces to
the 5.10 config.
Fixes: f724a583dc ("ath79: mikrotik: update nand-rb4xx driver")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This updates the NAND driver for MikroTik RB4XX series to work with
kernel 5.10, similarly to the ar934x-nand driver (fb64e2c3).
Support for kernel 5.10 was added to all ath79 subtargets except for the
mikrotik one by commit d6b785d, since patch 920-mikrotik-rb4xx.patch
needed to be reworked. Later, commit f8512661 enabled kernel 5.10 for
the mikrotik subtarget with the nand-rb4xx driver still pending, which
is updated and added back by this patch.
Compile-tested only.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch ist not required, as it only has an effect in case the GPIO
descriptors supplied to num-cs are valid.
As this is not the case for ath79, this patch can safely be omitted. The
issue it tried to fix is actually fixed with
0054-spi-sync-up-initial-chipselect-state.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD.
GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable
or disable transmission, but no change is observed. Therefore, it is
left as output high to ensure the SFP module is forced to transmit.
Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD
1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router
iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port
or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers
950 Mbps symmetric.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Fix the PLL register value for 10 Mbit/s link modes on TP-Link EAP
boards using a AR8033 SGMII PHY.
Otherwise, 10 Mbit/s links do not transfer data.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix the PLL register value for 10 Mbit/s link modes on the UniFi AC Lite
/ Mesh / LR. Otherwise, 10 Mbit/s links do not transfer data.
Signed-off-by: David Bauer <mail@david-bauer.net>
When adding the patch for the missing register, the patch file for the
testing kernel 5.10 was not included.
Fixes commit fbbad9a9a6 ("ath79: force SGMII SerDes
mode to MAC operation")
Signed-off-by: David Bauer <mail@david-bauer.net>
The mode on the SGMII SerDes on the QCA9563 is 1000 Base-X by default.
This only allows for 1000 Mbit/s links, however when used with an SGMII
PHY in 100 Mbit/s link mode, the link remains dead.
This strictly has nothing to do with the SerDes calibration, however it
is done at the same point in the QCA reference U-Boot which is the
blueprint for everything happening here. As the current state is more or
less a hack, this should be fine.
This fixes the issues outlined above on a TP-Link EAP-225 Outdoor.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Increase the spi-max frequency to 50 MHz, similar to the DIR-842.
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
[improve commit title, fix commit message alignment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
commit d6b785d477 ("ath79: add kernel 5.10 support") moved
KERNEL_TESTING_PATCHVER to a subtarget level,
but is looks like Mikrotik subtarget was forgotten.
Also add it for Mikrotik.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
pcie0 is the same for this generation of Senao APs
while eth0, eth1, and wmac can differ
the qca,no-eeprom property has no effect
for the ath10k drivers
Signed-off-by: Michael Pratt <mcpratt@pm.me>
use qca955x_senao_loader.dtsi
because it is the same hardware / partitioning
and some cleanup
Effects:
nodes to match similar boards
- keys
- eth0
- pcie0
bumps SPI frequency to 40 MHz
removes &pll node:
the property is defined in qca955x.dtsi
removes qca,no-eeprom:
has no effect with mtd-cal-data property
(also spelling)
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This device is a Senao-based product
using hardware and software from Senao
with the tar-gz platform for factory.bin
and checksum verification at boot time
using variables stored in uboot environment
and a 'failsafe' image when it fails.
Extremely similar hardware/software to Engenius EAP1200H
and other Engenius APs with qca955x
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Use a similar upgrade method for sysupgrade.bin, like factory.bin,
for Senao boards with the tar.gz OEM upgrade platform,
and 'failsafe' image which is loaded on checksum failure.
This is inspired by the OEM upgrade script /etc/fwupgrade.sh
and the existing platforms for dual-boot Senao boards.
Previously, if the real kernel was damaged or missing
the only way to recover was with UART serial console,
because the OKLI lzma-loader is programmed to halt.
uboot did not detect cases where kernel or rootfs is damaged
and boots OKLI instead of the failsafe image,
because the checksums stored in uboot environment
did not include the real kernel and rootfs space.
Now, the stored checksums include the space for both
the lzma-loader, kernel, and rootfs.
Therefore, these boards are now practically unbrickable.
Also, the factory.bin and sysupgrade.bin are now the same,
except for image metadata.
This allows for flashing OEM image directly from openwrt
as well as flashing openwrt image directly from OEM.
Make 'loader' partition writable so that it can be updated
during a sysupgrade.
tested with
ENS202EXT v1
EAP1200H
EAP350 v1
EAP600
ECB350 v1
ECB600
ENH202 v1
Signed-off-by: Michael Pratt <mcpratt@pm.me>
ath79/tiny kernel config has
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS=y
from commit
05d35403b2
Because of this, these changes are required for 2 reasons:
1.
Senao devices in ath79/tiny
with a 'failsafe' partition and the tar.gz sysupgrade platform
and a flash chip that supports 4k sectors
will fail to reboot to openwrt after a sysupgrade.
the stored checksum is made with the 64k blocksize length
of the image to be flashed,
and the actual checksum changes after flashing due to JFFS2 space
being formatted within the length of the rootfs from the image
example:
0x440000 length of kernel + rootfs (from sysupgrade.bin)
0x439000 offset of rootfs_data (from kernel log)
2.
for boards with flash chips that support 4k sectors:
saving configuration over sysupgrade is not possible
because sysupgrade.tgz is appended at a 64k boundary
and the mtd parser starts JFFS2 at a 4k boundary.
for boards with flash chips that do not support 4k sectors:
partitioning with 4k boundaries causes a boot loop
from the mtd parser not finding kernel and rootfs.
Also:
Some of the Senao boards that belong in ath79/tiny,
for example ENH202,
have a flash chip that does not support 4k sectors
(no SECT_4K symbol in upstream source).
Because of this, partitioning must be different for these devices
depending on the flash chip model detected by the kernel.
Therefore:
this creates 2 DTSI files
to replace the single one with 64k partitioning
for 4k and 64k partitioning respectively.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
By using the same custom kernel header magic
in both OKLI lzma-loader, DTS, and makefile
this hack is not necessary anymore
However, "rootfs" size and checksum
must now be supplied by the factory.bin image
through a script that is accepted by the OEM upgrade script.
This is because Senao OEM scripts assume a squashfs header exists
at the offset for the original "rootfs" partition
which is actually the kernel + rootfs in this implementation,
and takes size value from the header that would be there with hexdump,
but this offset is now the uImage header instead.
This frees up 1 eraseblock
previously used by the "fakeroot" partition
for bypassing the OEM image verification.
Also, these Senao devices with a 'failsafe' partition
and the tar-gz factory.bin platform would otherwise require
flashing the new tar-gz sysupgrade.bin afterward.
So this also prevents having to flash both images
when starting from OEM or 'failsafe'
the OEM upgrade script verifies the header magic numbers,
but only the first two bytes.
Example:
[ "${magic_word_kernel}" = "2705" ] &&
[ "${magic_word_rootfs}" = "7371" -o "${magic_word_rootfs}" = "6873" ] &&
errcode="0"
therefore picked the magic number
0x73714f4b
which is
'sqOK'
Signed-off-by: Michael Pratt <mcpratt@pm.me>
...and max flash offset
The mtdsplit parser was recently refactored
to allow the kernel to have custom image header magic.
Let's also do this for the lzma-loader
For example:
When implemented together,
this allows the kernel to "appear" to be a rootfs
by OEM software in order to write an image
that is actually kernel + rootfs.
At the same time,
it would boot to openwrt normally
by setting the same magic in DTS.
Both of the variables
have a default value that is unchanged
when not defined in the makefiles
This has no effect on the size of the loader
when lzma compressed.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label
on the case, not LAN.
This patch fixes this issue.
Fixes: 50fdc0374b ("ath79: provide label MAC address")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Straightforward refresh of patches using update_kernel.
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
