There are broken devices in the wild that handle duplicate IP address
detection by sending out ARP requests for the IP that they received from a
DHCP server and refuse the address if they get a reply.
When proxyarp is enabled, they would go into a loop of requesting an address
and then NAKing it again.
Fixes: https://github.com/openwrt/openwrt/issues/14309
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c1ad78318c)
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Power (green, unmanaged)
- 1x Status (green, gpio)
- 1x 2.4G (green, hardware, mt76-phy0)
- 1x 2.4G (blue, gpio)
- 1x 5G (green, hardware, mt76-phy1)
- 1x 5G (blue, gpio)
- 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (default http://192.168.0.1/)
under "admin" account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following block:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>
5. Replace <some value> by a new superadmin password and add a line
which enabling superadmin login after. For example, the block after
the changes:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit f3cdc9f988)
This fixes a well known "LZMA ERROR 1" error on Sercomm NA502,
reported on the OpenWrt forum. [1]
[1]: https://forum.openwrt.org/t/176942
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit d41b8a570f)
Add support for wireless offload package in default configuration for
-Cudy WR3000
-Confiabits MT7981
For some reason those ware missing. I confirm this work for my Cudy WR3000
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
(cherry picked from commit b42eea0c2f)
The label-mac of the repeater is the address used on the 2.4 GHz radio,
not the ethernet MAC.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 47818fbc01)
The Puzzle devices come with an I2C-connected Epson RX8130 RTC.
Disable the (dysfunctional) RTC units of the SoC and add driver
kmod-rtc-ds1307 to support the Epson RX8130 instead.
Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 6d546b3b4c)
Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981.
Specification:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 256 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN)
- USB 2.0 port
- Buttons: 1 Reset button, 1 Mesh button.
- LEDs: 7x light-blue, 2x warm-white
- Serial console: internal 4-pin header, 115200 8n1
- Power: 12 VDC, 1.5 A
MAC addresses in stock firmware and in this commit:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 00:0c:43:xx:xx:e1 | label+1 |
| LAN | 00:0c:43:xx:xx:e0 | label |
| WLAN 2g | 00:0c:43:xx:xx:e0 | label |
| WLAN 5g | 02:0c:43:xx:xx:e0 | |
+---------+-------------------+-----------+
The label MAC was found in 'Factory', 0x4
Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit 2af07eb853)
In 749237967a downstream dts was replaced with upstream accepted
patch. But in upstream version last partition was called "rootfs"
instead "ubi". OpenWrt require "ubi" label for ubi rootfs.
This patch restore proper label.
Fixes: 749237967a ("kirkwood: Replace dtses with upstream accepted")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cherry picked from commit 9075cfd609)
This service was unfunctional due to not having its executable bit
set.
Fixes#13500.
Signed-off-by: Eric J. Anderson <eric.j.ason256@gmail.com>
(cherry picked from commit 807acbce66)
We have a report in the forum, that lan/wan is non-functional
on the EAP102 (https://forum.openwrt.org/t/edgecore-eap102/178449)
Fixing that by swapping label and phy-handle of the dp-nodes and
updating the lan/wan bmp.
Note: the original commiter of the device support seems absent for a
long time in the forum and on the OpenWrt github group.
Tested-by: Antonio Della Selva <antonio.dellaselva@uniurb.it>
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9b598ec8d5)
[ fix conflicts errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi. There is no printed MAC label (on my unit).
My unit came with Mediatek's firmware (based on OpenWrt 21.02)
installed. It was possible to simply upgrade using OpenWrt's sysupgrade
tool.
Another verified upgrade method is using U-Boot (requires UART). During
every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
firmware" allows using U-Boot's tftp client to load and flash factory
image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 07765f28b7)
Quite a few `fiilogic` devices use the `mt7531` switch.
Some of them have a DT node that looks like:
```
switch: switch@0 {
compatible = "mediatek,mt7531";
reg = <31>;
...
};
```
This commit changes the DT node name to `switch@1f`.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(cherry picked from commit aaeb379023)
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.
[1] Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
(cherry picked from commit 36746893ac)
The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX
Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d99aed31a0)
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c8c2f52262)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: Winbond 128MB
RAM: DDR3 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
Power: DC 12V 1A
Flash instructions:
1. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
2. Attach UART, pause at u-boot menu.
3. Select "Upgrade ATF BL2", then use preloader.bin
4. Select "Upgrade ATF FIP", then use bl31-uboot.fip
5. Download the initramfs image, and type "reset",
waiting for tftp recovery to complete.
6. After openwrt boots up, perform sysupgrade.
Note:
1. Since NMBM is disabled, we must back up all partitions.
2. Although we can upgrade new firmware in the stock firmware,
we need the special fit image signature of MediaTek and
dual boot (hack kernel) to make u-boot boot it. So just
abandon these hacks and flash it via the serial port.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 626344c992)
Hardware
========
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
ETH: MediaTek MT7530 Switch (LAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
UART: 3V3 115200 8N1 (Do not connect VCC)
USB 3.1
Installation
============
Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.
Connect to the serial console, interrupt the auto boot process by
pressing '4' when prompted or press '1' and set client IP, server
IP and name of the image.
yOU don't need to open the case or even soldering anything.
use three goldpin wires, remove their plastic cover and connect
them to the console pinout via the case holes.
You can see three holes
From Bottom: RX, TX, Ground - partially covered
Download & Boot the OpenWrt initramfs image.
In case of option '4'
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 TUF-AX6000.bin
$ bootm 0x46000000
In case of option '1'
1: Load System code to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (TUF-AX6000.trx) ==:
Wait for OpenWrt to boot. Transfer the sysupgrade
image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
================
2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected
The cover yellow light is not supported. (only blue one)
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit d522ccecb2)
Commit mt76: drop default eeprom file for mt7986-firmware
(e3aa645b26) breaks eeprom loading for
Mercusys MR90X v1. As a result WiFi is not working at all.
This commit adds Mercusus MR90x to the caldata script (it works after the
commit mentioned above). And we can safely drop "81_fix_eeprom" script
as it's no longer required.
Fixes: 5a0bdab24c ("mt76: drop default eeprom file for mt7986-firmware")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 85b0d7592c)
[rmilecki: fix commit hash in Fixes]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The usb driver requires kmod-usb3, not kmod-usb2.
Remove the useless kmod-usb2 from default package.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit b74ae69596)
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
(cherry picked from commit 907e9e0bd3)
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.
Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree
Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
refuses to boot if it doesn't. The chosen "rootfs" volume must contain
a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
variable to the label mac. But "factoryparams" does not always
exist. Instead there is a "RIP" volume containing all the factory
data. Copying the "RIP" volume to "factoryparams" will fix this
Hardware
--------
SOC: MediaTek MT7986
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI: Mediatek MT7986 802.11ax 5 GHz
Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.2/24. Rename the image to C0A80101.img.
2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
console, Interrupt the autoboot process by pressing ESC when prompted.
3. Download and boot the OpenWrt initramfs image.
$ env set uboot_bootcount 0
$ env set firmware nominal
$ tftpboot
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
not configured by OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 6cc14bf66a)
The no-map property was incorrectly added, which kept the system-memory
available on the WS-AP3825 limited to 190MB. We are allowed to map the
page containing the CPU1 spin-table, we are just not allowed to write to
it.
Fixes: 57d7382cb1 ("mpc85xx: increase available RAM on Extreme Networks WS-AP3825i")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit d9271aa5b7)
The system-mamory size was page-aligned prior to this commit, only
enabling to use 192MB of system memory of the 256 available.
This was due to the system-memory being manually shrinked to reserve the
upper 1MB for the second-core bootpage in the loader as well as the OS.
Fix this properly in the loader and in Linux using reserved-memory
definitions. This enables the device to use 250MB of system memory.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 57d7382cb1)
This commit adds support for following wireless routers:
- Rostelecom RT-FL-1 (Serсomm RT-FL-1)
- Rostelecom S1010 (Serсomm S1010.RT)
The devices are almost identical and the only difference is one bit in the
factory image PID (thanks to Maximilian Weinmann <x1@disroot.org>
(@MaxS0niX) for the info and idea to make one PR for two devices at once).
Devices specification
---------------------
SoC: MediaTek MT7620A, MIPS
RAM: 64 MB
Flash: 16 MB SPI NOR
Wireless 2.4: MT7620 (b/g/n, 2x2)
Wireless 5: MT7612EN (a/n/ac, 2x2)
Ethernet: 5xFE (WAN, LAN1-4)
BootLoader: U-Boot
Buttons: 2 (wps, reset)
LEDs: 1 amber and 1 green status GPIO leds
5 green ethernet GPIO leds
1 green GPIO 2.4 GHz WLAN led
1 green PHY 5 GHz WLAN led
1 green unmanaged power led
USB ports: No
Power: 12 VDC, 1 A
Connector: Barrel
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Wait until green status led stops blinking (can take several minutes)
4. Login to OpenWrt initramsfs. It's recommended to make a backup of the
mtd partitions at this point.
4. Perform sysupgrade using the following command (or use Luci):
sysupgrade -n sysupgrade.bin
5. Wait until green status les stops blinking (can take several minutes)
6. Mission acomplished
Return to Stock
---------------
Option 1. Restore firmware Slot1 from a backup (firmware2.bin):
cd /tmp
mtd -e Firmware2 write firmware2.bin Firmware2
printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
reboot
Option 2. Decrypt, ungzip and split stock firmware image into the parts,
take Slot1 parts (kernel2.bin, rootfs2.bin) and write them:
cd /tmp
mtd -e Kernel2 write kernel2.bin Kernel2
mtd -e RootFS2 write rootfs2.bin RootFS2
printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
reboot
More about stock firmware decryption:
Link: https://github.com/Psychotropos/sercomm_fwutils/
Debricking
----------
Use sercomm-recovery tool. You can use "ALL" mtd partition backup as a
recovery image.
Link: https://github.com/danitool/sercomm-recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 48:3e:xx:xx:xx:1e | label |
| LAN | 48:3e:xx:xx:xx:1e | label |
| WAN | 48:3e:xx:xx:xx:28 | label+10 |
| WLAN 2g | 48:3e:xx:xx:xx:20 | label+2 |
| WLAN 5g | 48:3e:xx:xx:xx:24 | label+6 |
+---------+-------------------+-----------+
Co-authored-by: Vadzim Vabishchevich <bestmc2009@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 1b091311aa)
[fix rt2800_wmac eeprom load]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
This commit makes a common recipe to set bit in Sercomm factory pid since
this is necessary for several devices (WiFire S1500.nbn, Rostelecom
RT-FL-1) at different offsets.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit e900c45211)
Hardware:
- SoC: Mediatek MT7621 (MT7621AT)
- Flash: 32 MiB SPI-NOR (Macronix MX25L25635E)
- RAM: 128 MiB
- Ethernet: Built-in, 2 x 1GbE
- 3G/4G Modem: MEIG SLM828 (currently only supported with ModemManager)
- SLIC: Si32185 (unsupported)
- Power: 12V via barrel connector
- Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
- Wifi 5GHz: Mediatek MT7613BE 802.11ac/n/a
- LEDs: 8x (7 controllable)
- Buttons: 2x (RESET, WPS)
Installing OpenWrt:
- sysupgrade image is compatible with vendor firmware.
Recovery:
- Connect to any of the Ethernet ports, configure local IP:
10.10.10.3/24 (or 192.168.10.19/24, depending on OEM)
- Provide firmware file named 'mt7621.img' on TFTP server.
- Hold down both, RESET and WPS, then power on the board.
- Watch network traffic using tcpdump or wireshark in realtime to
observe progress of device requesting firmware. Once download has
completed, release both buttons and wait until firmware comes up.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit bc335f2967)
In addition to binary and ASCII-formatted MAC addresses, add support
for processing hexadecimal encoded MAC addresses from NVMEM.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7db87d7c68)
Another Qualcomm-based USB-connected modem, offering endpoints
0 : rndis_host (link to voip subsystem listening on 169.254.5.100)
1 : rndis_host (?)
2 : option (?)
3 : option (at)
4 : option (at)
5 : option (?)
6 : GobiNet (qmi)
7 : ?
Add support for this modem in rndis_host, option and qmi_wwan driver
which allows the modem to be used with ModemManager.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f32baf6a65)
Add support for COMFAST CF-EW72 V2
Hardware:
- SoC: Mediatek MT7621 (MT7621DAT or MT7621AT)
- Flash: 16 MiB NOR
- RAM: 128 MiB
- Ethernet: Built-in, 2 x 1GbE
- Power: only 802.3af PD on any port, injector supplied in the box
- PoE passthrough: No
- Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
- Wifi 5GHz: Mediatek MT7613BEN 802.11ac/n/a
- LEDs: 8x (only 1 is both visible and controllable, see below)
- Buttons: 1x (RESET)
Installing OpenWrt:
Flashing is done using Mediatek U-Boot System Recovery Mode
- make wired connection with 2 cables like this:
- - PC (LAN) <-> PoE Injector (LAN)
- - PoE Injector (POE) <-> CF-EW72 V2 (LAN). Leave unconnected to CF-EW72 V2 yet.
- configure 192.168.1.(2-254)/24 static ip address on your PC LAN
- press and keep pressed RESET button on device
- power the device by plugging PoE Injector (POE) <-> CF-EW72 V2 (LAN) cable
- wait for about 10 seconds until wifi led stops blinking and release RESET button
- navigate from your PC to http://192.168.1.1 and upload OpenWrt *-factory.bin firmware file
- proceed until router starts blinking with wifi led again (flashing) and stops (rebooting to OpenWrt)
MAC addresses as verified by OEM firmware:
vendor OpenWrt address
LAN lan\eth0 label
WAN wan label + 1
2g phy0 label + 2
5g phy1 label + 3
The label MAC address was found in 0xe000.
LEDs detailed:
The only both visible and controllable indicator is blue:wlan LED.
It is not bound by default to indicate activity of any wireless interfaces.
Place (WAN->ANT) | Num | GPIO | LED name (LuCI) | Note
-----------------|-----|-----------------------------------------------------------------------------------------
power | 1 | | | POWER LED. Not controlled with GPIO.
hidden_led_2 | 2 | 13 | blue:hidden_led_2 | This LED does not have proper hole in shell.
wan | 3 | | | WAN LED. Not controlled with GPIO.
hidden_led_4 | 4 | 16 | blue:hidden_led_4 | This LED does not have proper hole in shell.
lan | 5 | | | LAN LED. Not controlled with GPIO.
noconn_led_6 | 6 | | | Not controlled with GPIO, possibly not connected
wlan | 7 | 15 | blue:wlan | WLAN LED. Wireless indicator.
noconn_led_8 | 8 | | | Not controlled with GPIO, possibly not connected
mt76-phy0 and mt76-phy1 leds also exist in OpenWrt, but do not exist on board.
Signed-off-by: Alexey D. Filimonov <alexey@filimonic.net>
(cherry picked from commit ff95f859eb)
Add support for ComFast CF-E390AX. It is a 802.11 wifi6 cieling AP, based on MediaTek MT7261AT.
Specifications:
SoC: MediaTek MT7621AT
RAM: 128 MiB
Flash: 16 MiB NOR (Macronix mx25l12805d)
Wireless: MT7915E (2.4G) 802.11ax/b/g/n MT7915E (5G) 802.11ac/ax/n
Ethernet: 2 x 1Gbs
Button: 1 x "Reset" button
LED: 1x Blue LED + 1x Red LED + 1x green LED
Power: PoE
Manufacturer Page:
http://en.comfast.com.cn/index.php?m=content&c=index&a=show&catid=84&id=75
Flash Layout:
0x000000000000-0x000000030000 : "bootloader"
0x000000030000-0x000000040000 : "config"
0x000000050000-0x000000060000 : "factory"
0x000000090000-0x000001000000 : "firmware"
First install:
1. Set device into http firmware fail safe upload mode by pressing the reset button for 10 seconds while powering
it on. Once the LED stops flashing, safe mode will be running.
2. Set PC IP address to 192.168.1.2
3. Browse to 192.168.1.1 and upload the factory image using the web interface.
Signed-off-by: Usama Nassir <usama.nassir@gmail.com>
(cherry picked from commit f24c9b9d86)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 423186d7d8)
[rebased to 23.05]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The MAC-address of gmac0 matches the one printed on the bottom label.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ae500e62e2)
DT binding for MAC cells in fixed layout was upstream approved and
accepted. Add support for it. This can replace quite some of our
downstream hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 61f674df4f)
Add build for the MTK3943 reference board for MT7981B+MT7976C.
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: various options
- RAM: 256MB DDR3
- Ethernet: 4 x 10/100/1000 Mbps via MT7531AE switch
EITHER 1 x 10/100/1000 Mbps built-in PHY
OR 1 x 10/100/1000/2500 Mbps MaxLinear GPY211C
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: RST, WPS
**Flash instructions for SPIM-NAND:**
- write *mt7981-rfb-spim-nand-preloader.bin to 'BL2' partition
- write *mt7981-rfb-spim-nand-bl31-uboot.fip to 'FIP' partition
- erase 'ubi' partition
- reset board
- create ubootenv and ubootenv2 UBI volumes in U-Boot
- edit environment and set bootcmd, e.g.
setenv bootconf 'config-1#mt7981-rfb-spim-nand#mt7981-rfb-mxl-2p5g-phy-eth1'
setenv bootcmd 'ubi read $loadaddr fit; bootm $loadaddr#$bootconf'
- load initramfs image via TFTP:
setenv serverip 192.168.1.254
setenv ipaddr 192.168.1.1
setenv bootfile openwrt-mediatek-filogic-mediatek_mt7981-rfb-initramfs.itb
saveenv ; saveenv
tftpboot
bootm $loadaddr#$bootconf
- Now use sysupgrade to write OpenWrt firmware to flash.
SNFI-NAND, SPIM-NOR and eMMC all work very similar, a bootable SD card image
is also being generated. However, as the board I've been provided only comes
with SPIM-NAND all other boot media are untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ce7209bd21)
UARTs not used as boot console are currently broken on some MediaTek
targets due to register access depending on the bus clock being enabled.
Add patch to make sure this dependency is always met.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9f62abbb60)
Due to circuit issue or silicon defect, sometimes the WiFi switch button
of the Archer C7 v2 can be accidentally triggered multiple times in one
second. This will cause WiFi to be unexpectedly shut down and trigger
'irq 23: nobody cared'[1] warning. Increasing the key debounce interval
to 1000 ms can fix this issue. This patch also add the missing rfkill
key label.
[1] Warning Log:
```
[87765.218511] irq 23: nobody cared (try booting with the "irqpoll" option)
[87765.225331] CPU: 0 PID: 317 Comm: irq/23-keys Not tainted 5.15.118 #0
...
[87765.486246] handlers:
[87765.488543] [<85257547>] 0x800c29a0 threaded [<5c6328a2>] 0x80ffe0b8 [gpio_button_hotplug@4cf73d00+0x1a00]
[87765.498364] Disabling IRQ #23
```
Fixes: https://github.com/openwrt/openwrt/issues/13010
Fixes: https://github.com/openwrt/openwrt/issues/12167
Fixes: https://github.com/openwrt/openwrt/issues/11191
Fixes: https://github.com/openwrt/openwrt/issues/7835
Tested-by: Hans Hasert
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit e32f70e706)
HiWiFi HC5861 has a GbE port which connected to the RTL8211E PHY
chip. This patch adds the missing Realtek PHY driver package and
sets the correct external PHYs base address to make it work again.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit f025135f16)
This makes it possible to build the ipq807x netgear-wax218 without initramfs - which is required for downstream projects (gluon)
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
(cherry picked from commit b3d2008f92)
Kernel 5.15 already supports the NanoPi R1 and NanoPi R1S H5,
and they use new LED bindings that do not match the existing
settings in 01_leds. Update led settings to fixes that.
List the led node on NanoPi R1S H5:
root@OpenWrt:~# ls /sys/class/leds/
green:lan green:wan red:status
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit b25c7548e0)
This will help switching to newer 5.15 kernels. This backport required
rebasing Northstar's USB host patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit c25c1e28b7)
Designated initializers are required when using the randstruct GCC
plugin, otherwise an error like the following is seen:
./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init]
This was originally applied via 55643e469c, but was unintentionally
reverted in 483503603c.
Fixes: 483503603c ("generic: 5.15: rework pending patch")
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
(cherry picked from commit b2068f4aac)
[ drop change for unavailable kernel 6.1 ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Among other changes this commit makes Linux use correct switch ports
again.
Fixes: a4792d79e8 ("bcm53xx: backport DT changes from v6.5")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a67af19bc8)
We now have all raw ports defined in bcm-ns.dtsi. Leave only lables in
custom device files.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 08ce0c76d7)
So far every build of a single bcm53xx Target Profile (it means: when
NOT using CONFIG_TARGET_MULTI_PROFILE) resulted in all target devices
images being built. Now it only builds the one matching selected
profile.
Fixes: #13572
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
[rmilecki: update commit subject + body & move PROFILES line]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 802a5f5cb4)
ASUS RT-AC3100 is ASUS RT-AC88U without the external switch.
OpenWrt forum users effortless and ktmakwana have confirmed that there are
revisions with either 4366b1 or 4366c0 wireless chips.
Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 2214bab350)
As already documented in the wiki (https://openwrt.org/toh/wavlink/quantum_dax_wn538a8),
this router is based on the Phicomm K3. Just the flashing method is different
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
(cherry picked from commit f1136fe1fd)
1) clear nvram partialboots upon successful boot
This behavior is already defined for EA9500; enabled for EA9200 too.
2) fix MAC address in board.d/02_network
Use the correct nvram variable to derive lan/wan MAC address.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(cherry picked from commit 9c42d23c5f)
Set correct GPIO (10) for the WPS button. This matches GPIO settings in
vendor GPL sources. Note that GPL sources also mention a USB indicator
LED (GPIO 13) but the device has neither an external USB port nor a USB LED.
In addition, prefixes (button-, led-) are added to relevant DT entries,
as well as color and function specifications for LEDs.
Closes: #13736
Reported-by: Waldemar Czabaj <kaball@wp.pl>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(added led mitigations for wifi leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit fe5e498777)
This reverts commit 0c117e1f6c.
Activate the lantiq/xrx200 target again.
There are still some problems with the GSWIP, but it is not leaking
packets to the wrong bridge in normal operations.
It shows some error messages at configuration like these:
[ 54.308861] gswip 1e108000.switch: port 5 failed to add ce:9d:84:d1:81:f0 vid 1 to fdb: -22
[ 54.325633] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 0 to fdb: -22
[ 54.351242] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 1 to fdb: -22
[ 54.358311] gswip 1e108000.switch: port 5 failed to delete ce:9d:84:d1:81:f0 vid 1 from fdb: -2
The problems are described in this pull request:
https://github.com/openwrt/openwrt/pull/13200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e1aaa1defd)
prepend-dtb got extended to handle the Meraki devices too,
the problem here was that the Netgear WNDR4700 expects an
u-boot header in front of the DTB, whereas Meraki devices
don't.
Since the header was dropped, the WNDR4700's uboot started
to complain:
Bad Magic Number,it is forbidden to be written to flash!!
when flashing the factory.img since it expects an u-boot
header there.
Fixes: 5dece2d9355a ("apm821xx: switch over from DTB_SIZE to DEVICE_DTC_FLAGS")
Fixes: #13716
Reported-by: @kisgezenguz
Reported-by: Tamas Szabo
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit d6a11833ad)
Like with some other ipq40xx devices, the kernel image size for the WPJ428
is limited in stock u-boot. For that reason, the current release doesn't
include an image for the board.
By switching to the zImage format, the kernel image size is reduced which
re-enables the build process. The image boots and behaved normally through
a few days of testing.
Before the switch to kernel version 6.1, it was possible to reduce the
image size by enough when disabling UBIFS and its otherwise unneeded
dependencies.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit 2657e8cab7)
Doing a simple ping to my device shows this:
64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=2.00 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=2.02 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=1.68 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=1.91 ms
64 bytes from 10.0.253.101: icmp_seq=5 ttl=64 time=1.92 ms
64 bytes from 10.0.253.101: icmp_seq=6 ttl=64 time=2.04 ms
Some users even report higher values on older kernels:
64 bytes from 192.168.1.10: seq=0 ttl=64 time=0.612 ms
64 bytes from 192.168.1.10: seq=1 ttl=64 time=2.852 ms
64 bytes from 192.168.1.10: seq=2 ttl=64 time=2.719 ms
64 bytes from 192.168.1.10: seq=3 ttl=64 time=2.741 ms
64 bytes from 192.168.1.10: seq=4 ttl=64 time=2.808 ms
The problem is that the governor is set to Ondemand, which causes
the CPU to clock all the way down to 48MHz in some cases.
Switching to performance governor:
64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=0.528 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=0.561 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=0.633 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=0.526 ms
In theory, using the Performance governor should increase power draw,
but it looks like it really does not matter for this soc.
Using a calibrated precision DC power supply (cpu idle):
Ondemand
24.00V * 0.134A = 3.216 Watts
48.00V * 0.096A = 4.608 Watts
Performance
24.00V * 0.135A = 3.240 Watts
48.00V * 0.096A = 4.608 Watts
Let's simply switch to the Performance governor by default
to fix the general jittery behaviour on devices using this soc.
Tested on: MikroTik wAP ac
Fixes: #13649
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(cherry picked from commit b8e52852bd)
Copy configuration to boot partition (partition 1) instead of root
partition (partition 2) because the root partition is not writable if
it's a suqashfs image.
Move configuration back to root during preinit.
Fixes: https://github.com/openwrt/openwrt/issues/13695
Signed-off-by: Christian Buschau <cbuschau@d00t.de>
(cherry picked from commit 67ce60c5f9)
A typo snuck in with the addition of Cudy M1800, changing
"nr7101" to "nt7101". The result is a default network config
for NR7101 without the only ethernet interface on the NR7101,
thereby soft bricking it.
Fixes: f6d394e9f2 ("ramips: add support for Cudy M1800")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 2e57028424)
Hardware information:
---------------------
- RTL8380 SoC
- 8 Gigabit RJ45 PoE ports (built-in RTL8218B)
- 2 SFP ports (built-in SerDes)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
- PoE chip
- Fanless
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '65'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
(cherry picked from commit f4ee08677c)
There are two hardware models of the HPE 1920-8g-poe switch. The version
currently in the repository is the model with a PoE budget of 180W. In
preparation of the addition of the 65W model, the existing model is
renamed to clarify the hardware version it targets.
As suggested by Pawel, the 'SUPPORTED_DEVICES' includes the old target
name to enable an upgrade path of builds with the old name.
Suggested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
(cherry picked from commit 987c96e889)
The compex WPJ563 actually has both usb controllers wired:
usb0 --> pci-e slot
usb1 --> pin header
As the board exposes it for generic use, enable this controller too.
fixes: #13650
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(cherry picked from commit 9188c77cbe)
The USXGMII implementation of Realtek switches can not only support
10GbE but also 2.5Gb and 5Gb on top of the usual data rates.
Mark those as supported to allow them to be negotiated.
This change has been tested on a ZyXEL XGS1250-12 with the following link
partners:
- NWA50AX Pro (2.5Gb)
- RTL8152 USB NIC (2.5Gb)
- AQC111 USB NIC (2.5Gb & 5Gb)
Gbit and 10GbE has also been tested to still work fine with a variety of
devices.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
(cherry picked from commit cd56a68232)
Fix Spanning Tree Protocol (STP) by changing COPY2CPU which currently
makes switch to ignore Bridge Protocol Data Units (BPDUs).
Tested on Zyxel GS1900-8, 24 and 48.
Signed-off-by: Rudolf Vesely <i@rudolfvesely.com>
[ improve commit description and add new line in different sections ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 41fcc617f9)
This condition was introduced in commit 51c8f76612 ("realtek: Improve
MAC config handling for all SoCs") to correctly report the speed of the
internal serdes ports as 10G, but instead makes all ports read 10G
because the or-operator should have been an and-operator.
Fixes: #9953
Fixes: 51c8f76612 ("realtek: Improve MAC config handling for all SoCs")
Signed-off-by: Peter Körner <git@mazdermind.de>
[ wrap comment to 72 column and improve commit ref ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 9fb5082e25)
A bug report in the forum found that the MR70X lists four LAN ports in LuCI
while it has only three. This adds the device to the network setup file
to fix the issue.
Identified-by: Forum User "Lexeyko"
Signed-off-by: Andreas Böhler <dev@aboehler.at>
The reset button was missing from the Enterasys WS-AP3715i DTS.
Add the node required for making the reset button work.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 0e8641d3b0)
Label MAC detection does not work properly, as MAC address is assigned
on preinit. Thus, remove the label-mac definition.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cd14b17cb0)
Commit d5a05e69ac6e4 ("net: stmmac: Use hrtimer for TX coalescing") causes
high CPU usage due to hrtimer raw spin locks.
Fixes: #11676
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[ renumber and rename revert patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
While refactoring support for the MF287 series, an entry in platform.sh
was overlooked - this fixes sysupgrade on this devices.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 964b576fc1)
Since kernel 5.13 this is needed to enable USB ports on all devices in
subtarget. Previously TF-A and COMPHY driver might have set up this PHY,
but not anymore.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit eac1928430)
Turn the "gpio-restart" node into a "gpio-export" node for all MF287
variants, similar to the MF287 Pro. Unfortunately, there doesn't seem to be
a "power button blocker" GPIO for the MF287 and MF287 Plus, so a modem
reset always triggers a system reset.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 053f8f92d1)
The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 9c7578d560)
Ethernet LED assignments were incorrectly swapped. Fix the assignment
logic so the correct LED is illuminated for the LAN LEDs.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 8037417744)
For the ZTE MF287 series, a special recovery image is built. The Makefile
worked fine on snapshot, but created corrupt images on the 23.05 images.
By using the appropriate variable, this should be fixed.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit a9cc3708e0)
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.
Signed-off-by: Max Qian <public@maxqia.com>
(cherry picked from commit 794349a28a)
