mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 15:32:33 +00:00
ramips: add support for MeiG SLT866 4G CPE
Hardware: - SoC: Mediatek MT7621 (MT7621AT) - Flash: 32 MiB SPI-NOR (Macronix MX25L25635E) - RAM: 128 MiB - Ethernet: Built-in, 2 x 1GbE - 3G/4G Modem: MEIG SLM828 (currently only supported with ModemManager) - SLIC: Si32185 (unsupported) - Power: 12V via barrel connector - Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b - Wifi 5GHz: Mediatek MT7613BE 802.11ac/n/a - LEDs: 8x (7 controllable) - Buttons: 2x (RESET, WPS) Installing OpenWrt: - sysupgrade image is compatible with vendor firmware. Recovery: - Connect to any of the Ethernet ports, configure local IP: 10.10.10.3/24 (or 192.168.10.19/24, depending on OEM) - Provide firmware file named 'mt7621.img' on TFTP server. - Hold down both, RESET and WPS, then power on the board. - Watch network traffic using tcpdump or wireshark in realtime to observe progress of device requesting firmware. Once download has completed, release both buttons and wait until firmware comes up. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit is contained in:
Daniel Golle
parent
f8414f1a6f
commit
bc335f2967
245
target/linux/ramips/dts/mt7621_meig_slt866.dts
Normal file
245
target/linux/ramips/dts/mt7621_meig_slt866.dts
Normal file
@ -0,0 +1,245 @@
|
||||
#include "mt7621.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "meig,slt866", "mediatek,mt7621-soc";
|
||||
model = "MeiG SLT866";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_internet;
|
||||
led-failsafe = &led_internet;
|
||||
led-upgrade = &led_internet;
|
||||
label-mac-device = &gmac1;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
signal4 {
|
||||
label = "blue:signal4";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
lanwan {
|
||||
label = "blue:lanwan";
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_internet: internet {
|
||||
label = "blue:internet";
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wifi {
|
||||
label = "blue:wifi";
|
||||
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
signal3 {
|
||||
label = "blue:signal3";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
signal2 {
|
||||
label = "blue:signal2";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
signal1 {
|
||||
label = "blue:signal1";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
regulator-pa-5g {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "pa-5g";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
|
||||
&state_default {
|
||||
gpio {
|
||||
groups = "jtag", "uart2", "uart3", "wdt";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <20000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Bootloader";
|
||||
reg = <0x0 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "Config";
|
||||
reg = <0x30000 0x10000>;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "Factory";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
compatible = "nvmem-cells";
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x200>;
|
||||
};
|
||||
|
||||
eeprom_factory_8000: eeprom@8000 {
|
||||
reg = <0x8000 0x4da8>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "firmware";
|
||||
compatible = "denx,uimage";
|
||||
reg = <0x50000 0xf90000>;
|
||||
};
|
||||
|
||||
partition@fe0000 {
|
||||
label = "m_custom";
|
||||
reg = <0xfe0000 0x20000>;
|
||||
read-only;
|
||||
compatible = "nvmem-cells";
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_custom_0: macaddr@0 {
|
||||
reg = <0x0 0xc>;
|
||||
compatible = "mac-base";
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
macaddr_custom_40: macaddr@40 {
|
||||
reg = <0x40 0xc>;
|
||||
compatible = "mac-base";
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
macaddr_custom_100: macaddr@100 {
|
||||
reg = <0x100 0xc>;
|
||||
compatible = "mac-base";
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
macaddr_custom_140: macaddr@140 {
|
||||
reg = <0x140 0xc>;
|
||||
compatible = "mac-base";
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@1000000 {
|
||||
label = "fota_bak";
|
||||
reg = <0x1000000 0x1000000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
nvmem-cells = <&macaddr_custom_40 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "okay";
|
||||
label = "wan";
|
||||
phy-handle = <ðphy4>;
|
||||
|
||||
nvmem-cells = <&macaddr_custom_0 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
ethphy4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@3 {
|
||||
status = "okay";
|
||||
label = "lan";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
mt76@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cells = <&eeprom_factory_0>, <&macaddr_custom_100 0>;
|
||||
nvmem-cell-names = "eeprom", "mac-address";
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
mt76@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
ieee80211-freq-limit = <5000000 6000000>;
|
||||
nvmem-cells = <&eeprom_factory_8000>, <&macaddr_custom_140 0>;
|
||||
nvmem-cell-names = "eeprom", "mac-address";
|
||||
};
|
||||
};
|
||||
@ -1616,6 +1616,17 @@ define Device/mediatek_mt7621-eval-board
|
||||
endef
|
||||
TARGET_DEVICES += mediatek_mt7621-eval-board
|
||||
|
||||
define Device/meig_slt866
|
||||
$(Device/dsa-migration)
|
||||
IMAGE_SIZE := 15104k
|
||||
DEVICE_VENDOR := MeiG
|
||||
DEVICE_MODEL := SLT866
|
||||
DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
|
||||
kmod-usb-net-qmi-wwan kmod-usb-serial-option kmod-usb3 \
|
||||
kmod-usb-net-rndis
|
||||
endef
|
||||
TARGET_DEVICES += meig_slt866
|
||||
|
||||
define Device/mercusys_mr70x-v1
|
||||
$(Device/dsa-migration)
|
||||
$(Device/tplink-safeloader)
|
||||
|
||||
@ -138,6 +138,10 @@ linksys,ea8100-v2)
|
||||
ucidef_set_led_netdev "lan4" "lan4 link" "green:lan4" "lan4" "link"
|
||||
ucidef_set_led_netdev "wan" "wan link" "green:wan" "wan" "link"
|
||||
;;
|
||||
meig,slt866)
|
||||
ucidef_set_led_netdev "lan" "eth" "blue:lanwan" "lan" "link tx rx"
|
||||
ucidef_set_led_netdev "wwan0" "net" "blue:internet" "wwan0" "link tx rx"
|
||||
;;
|
||||
mikrotik,routerboard-760igs)
|
||||
ucidef_set_led_netdev "sfp" "SFP" "blue:sfp" "sfp"
|
||||
;;
|
||||
|
||||
@ -157,7 +157,8 @@ ramips_setup_interfaces()
|
||||
ucidef_set_interface "qtn" ifname "eth1" protocol "static" ipaddr "1.1.1.1" netmask "255.255.255.0"
|
||||
;;
|
||||
comfast,cf-e390ax|\
|
||||
comfast,cf-ew72-v2)
|
||||
comfast,cf-ew72-v2|\
|
||||
meig,slt866)
|
||||
ucidef_set_interfaces_lan_wan "lan" "wan"
|
||||
;;
|
||||
*)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user