Commit Graph

1332 Commits

Author SHA1 Message Date
David Bauer
7dceef5ee5 ramips: add support for TP-Link Archer AX23 v1
Hardware
--------
CPU:    MediaTek MT7621 DAT
RAM:    128MB DDR3 (integrated)
FLASH:  16MB SPI-NOR ()
WiFi:   MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
        LEDs - (3V3 - GND - RX - TX) - ETH ports

Installation
------------

Upload the factory image using the Web-UI.

Web-Recovery
------------

The router supports a HTTP recovery mode by holding the reset-button
when powering on. The interface is reachable at 192.168.0.1 and supports
installation using the factory image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-15 01:44:29 +01:00
Aleksey Nasibulin
d45659a571 ramips: add support for SNR-CPE-ME2-SFP
SNR-CPE-ME2-SFP is a wireless router with SFP cage manufactured by SNR/NAG company.

Specification:
- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB (GD25Q127CSIG)
- RAM:  256 MB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7615DN)
- Ethernet: 4x 10/100/1000 Mbps
- SFP cage (using RTL8211FS-CG)
- USB 3.0 port
- Power: 12 VDC, 2 A

Flash instruction via TFTP:
1. Boot SNR-CPE-ME2 to recovery mode
  (press reset button and power on device, hold button for ~10 seconds)
2. Send firmware via TFTP client:
 TFTP Server address: 192.168.1.1
 TFTP Client address: 192.168.1.131
3. Wait ~120 seconds to complete flashing
4. Do sysupgrade using web-interface

MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use      | address          | example           |
+----------+------------------+-------------------+
| Device   | label            | 6A:C4:DD:xx:xx:28 |
| Ethernet | + 1              | 6A:C4:DD:xx:xx:29 |
| 2g       | + 2              | 6A:C4:DD:xx:xx:2A |
| 5g       | + 3              | 6A:C4:DD:xx:xx:2B |
+----------+------------------+-------------------+

Notes:
- Reading sfp eeprom is not supported [1] (driver issue). Stock image has the same situation.

References:
1. https://forum.openwrt.org/t/mt7621-and-reading-sfp-eeprom/152249

Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
2023-03-08 23:44:59 +01:00
Mikhail Zhilkin
1f53fa2b83 ramips: fix wrong pcie port number for Arcadyan WE420223-99
Wrong pcie port number for WLAN causes missing 5g WLAN interface with 5.15
kernel on Arcadyan WE420223-99 (KPN Experia WiFi).

This changes port from pcie0 to pcie1.

[1.331556] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[1.345299] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[1.359116] mt7621-pci 1e140000.pcie: PCIE1 enabled

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-03-04 13:34:08 +01:00
Hang Zhou
e451957166 ramips: add support for D-Link Dir-853 A1
Specifications:
* SoC: MT7621AT
* RAM: 256MB (NT5CC64M16GP-DI)
* Flash: 16MB NOR SPI flash (GD25Q127CSIG, using GD25Q128C driver)
* WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC
* Ethernet: 4x1000M LAN, 1x 1000M WAN
* LEDs: Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue,
  USB Blue
* Buttons: Reset,WPS, Wifi
* Serial interface: on board but not populated, pinout (from the DC jack
side to the WAN port side) is "3.3V Input Output Gnd". Baud rate is 57600,
settings are 8 data bits, no parity bit, one stop bit, and no flow control.

Stock flash layout:
```
GD25Q128C(c8 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K)
.numeraseregions = 0
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "Config2"
0x000000060000-0x000000fb0000 : "Kernel"
0x000000fb0000-0x000001000000 : "Private"
```
The kernel partition will be replaced with the OpenWrt image, the other
partitions are left untouched.

"Config2" seems to be the config storage used by the stock firmware.

"Private" is a 320kB empty JFFS2 partition that comes with the stock
firmware. One can get a larger space for OpenWrt by merging it with
"Kernel".

OpenWrt flash layout:
```
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "u-boot-env"
0x000000040000-0x000000050000 : "factory"
0x000000050000-0x000000060000 : "config2_stock"
0x000000060000-0x000000fb0000 : "firmware"
0x000000fb0000-0x000001000000 : "private_stock"
```

The OpenWrt image must have 96 bytes of padding in the header.

MAC addresses on OEM firmware:
|      		| location on the flash 	| notes    	|
|------		|-----------------------	|----------	|
| lan (eth2) 	| factory + 0xe000      	| on label 	|
| wan (eth3) 	| factory + 0xe006      	|          	|
| 2.4g (rax0) 	| not on flash          	| lan + 1  	|
| 5g (ra0) 	| not on flash          	| lan + 2  	|

Mac addresses of the 2.4g and 5g interface are stored as ASCII strings in
the u-boot-env partition, but they are not used. OpenWrt calculates
Wifi Mac addresses based on the LAN Mac.

Flash and test instructions:
Flash the encrypted image (available in the OpenWrt forum) through the
stock D-Dink web interface.

1. Open the case, and solder the 4-pin header near the WAN port.
2. Connect it to a USB-UART TTL (3.3V) adapter, no need to connect VCC.
3. Open a terminal emulator (e.g. `screen /dev/ttyUSB0` on linux) with
the settings mentioned above.
4. Setup a TFTP server on your PC that can serve
`xxx-ramips-mt7621-dlink_dir-853-a1-initramfs-kernel.bin`.
5. Connect any LAN port to your PC and set a static IPv4 address to
192.168.0.101 (netmask 255.255.255.0).
6. Power on the device and keeps pressing 1 until you see the prompt.
7. Use default IP addresses and enter the file name accordingly, then hit
enter.
8. Wait until it boots to OpenWrt, the default IP address is 192.168.1.1,
you need to change your PC network adapter to use DHCP in order to access
LUCI.
9. So far, the OpenWrt runs in RAM and the flash contents are not touched.
You can try OpenWrt without having to overwrite the stock firmware, a
reboot clears all changes.
10. Optionally, backup the stock firmware (the "firmware" partition) in
Luci.
11. To permantly install OpenWrt to the device , click
on "System -> Backup/Flash Firmware" in Luci and flash
`xxx-ramips-mt7621-dlink_dir-853-a1-squashfs-sysupgrade.bin`

Known problems:
* WLAN0 defaults to 5G after a fresh installation, to enable 2.4G network,
you need to config it manually in LUCI.

* If you see jffs2 related warnings/errors after updating from the stock
web interface, you need to do a reset in LUCI. The error will be gone after
a cold reboot.

Signed-off-by: Hang Zhou <929513338qq@gmail.com>
2023-03-04 13:23:18 +01:00
Arınç ÜNAL
9df035b3ea treewide: remove label = "cpu" from DSA dt-binding
This is not used by the DSA dt-binding, so remove it from all devicetrees.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9cc115d8d6f73dd260de1609182f3645844d6907
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-26 22:22:48 +01:00
Felix Baumann
688697889c ramips: correct the PCIe port number for some mt7621 devices
MT7621 uses a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Netgear R6220, WAC104 and WNDR3700 v5.

According to bootlog, MT7612E (5GHz) is connected to pcie0, and
MT7603E (2GHz) is connected to pcie2:
[2.758986] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
[2.772862] mt7621-pci 1e140000.pcie: PCIE0 enabled
[2.782579] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[3.009151] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[3.125715] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000

Tested-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[felix.bau@gmx.de: adjust commit message for Netgear devices]
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-25 20:21:36 +01:00
Shiji Yang
c77913be5b ramips: correct the PCIe port number for Zbtlink ZBT-WE1326
MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Zbtlink ZBT-WE1326.

According to the bootlog, MT7612E (5 GHz) is connected to pcie1, and
MT7603E (2 GHz) is connected to pcie2:
[4.197658] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[4.204609] mt7621-pci 1e140000.pcie: PCIE1 enabled
[4.209476] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[4.307988] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[4.367206] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-02-19 18:37:55 +01:00
Arınç ÜNAL
efbb623deb ramips: add support for Huasifei WS1208V2
The Huasifei WS1208V2 is an AC1200 router featuring 5 Ethernet ports with a
Quectel RM520N-GL cellular modem which supports QMI and MBIM modes.

Specifications:
- MT7621AT, 256 MiB RAM, 16 MiB SPI Flash
- MT7603EN 2.4 GHz & MT7612EN 5 GHz WLAN
- Quectel RM520N-GL Cellular Modem
- 2 WLAN & 4 Cellular Antennas
- 5 Gigabit Ethernet Ports
- 1 USB 2.0 port
- 1 PCI-E Slot
- 1 M.2 slot
- 1 SIM card slot
- 1 SD card slot

Installation:
- Install sysupgrade image via ROOter OS.

TFTP Recovery:
- Connect to serial console.
- Boot initramfs image by choosing option 1 when U-Boot prompts.
- Install sysupgrade image via OpenWrt.

Link: https://www.huasifei.com/a/Products/5G%20CPE/240.html
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-18 19:56:37 +01:00
Michael Pratt
4ef86c620f ramips: add support for Senao Engenius EPG600
FCC ID: A8J-EPG600

Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)

this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.

**Specification:**

  - MT7620 SOC		MIPS 24kec, 2.4 GHz WMAC, 2x2
  - RT5592N WLAN	PCI chip, 5 GHz, 2x2
  - QCA8337N Gb SW	RGMII GbE, SW P0 -- SOC P5, 5 LEDs
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 64 MB RAM		NT5TU32M16
  - UART console	J2, populated
  - USB 2.0 port	direct to SOC
  - 6 GPIO LEDs		power, 2G, 5G, wps2g, wps5g, line
  - 3 buttons		reset, wps, "reg" (registeration)
  - 4 antennas		internal omni-directional plates

NOT YET SUPPORTED: VoIP

  - Si3050-FT + Si3019-FT	Voice DAA, SPI control, PCM data
  - Phone Ports "TEL", "LINE"	RJ11, 4P2C (2 pins)

**MAC addresses:**

  MAC address labeled as MAC ADDRESS
  MACs present in both wifi cal data and uboot environment

  eth0.1/phy1	----	*:82	rf 0x4
  phy0		----	*:83	factory 0x4
  eth0.2	MAC	*:b8	"wanaddr"

**Installation:**

  Method 1: Firmware upgrade page:

    (if you cannot access the APs webpage)
    factory reset with the reset button
    connect ethernet to a computer
    OEM webpage at 192.168.0.1
    username and password 'admin'

    Navigate to gear icon, "Device Management", "Tools"
    select the factory.dlf image
    Upload and verify checksum

  Method 2: Serial to upload initramfs:

    Follow directions for TFTP recovery
    upload and boot initramfs and do a sysupgrade

**TFTP recovery:**

  Requires UART serial console, reset button does nothing

  rename initramfs-kernel.bin to 'uImageEPG600'
  make available on TFTP server at 192.168.99.8
  power board, interrupt boot with "4"
  execute `tftpboot` and `bootm` (with the load address)

**Return to OEM:**

  Images from OEM are provided, but not compatible
  with openwrt sysupgrade. So it must be modified.

  Alternatively, back up all mtd partitions before flashing

**Note on switch registers:**

  The necessary registers needed for the QCA8337 switch
  can be read from interrupted boot (tftpboot, bootm)
  by using the following lines in the switch driver ar8327.c
  in the function 'ar8327_hw_config_of'
  where 'qca,ar8327-initvals' is parsed from DTS
  before the new register values are written:

    pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
    pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
    pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
    pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Mikhail Zhilkin
51e5f22096 ramips: fix wrong pcie port number for Arcadyan devices
Wrong pcie port number for WLAN causes missing 5g WLAN interface with 5.15
kernel. This changes port from pcie0 to pcie1 in dtsi.

[1.166330] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[1.180073] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[1.193889] mt7621-pci 1e140000.pcie: PCIE1 enabled

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-02-17 16:30:32 +02:00
Karl Chan
92276eef70 ramips: add support for ASUS RT-AX54
Specifications:
- Device: ASUS RT-AX54 (AX1800S/HP,AX54HP)
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x POWER (blue, configurable)
        1x LAN (blue, configurable)
        1x WAN (blue, configurable)
	1x 2.4G (blue, not configurable)
	1x 5G (blue, not configurable)

Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
   Select "2. Upgrade firmware"
   Press enter when show "Run firmware after upgrading? (Y/n):"
   Select 0 for TFTP method
   Input U-Boot's IP address: 192.168.1.1
   Input TFTP server's IP address: 192.168.1.2
   Input IP netmask: 255.255.255.0
   Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"

Signed-off-by: Karl Chan <exkc@exkc.moe>
2023-02-12 18:27:45 +01:00
Felix Baumann
d87482a8db
ramips: fix dts whitespace
Replace blanks with tabs
Remove whitespace from otherwise empty lines

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-02-09 03:03:52 +01:00
Arınç ÜNAL
5155200f97 ramips: mt7621-dts: fix phy-mode of external phy on GB-PC2
The phy-mode property must be defined on the MAC instead of the PHY. Define
phy-mode under gmac1 which the external phy is connected to.

Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-03 14:11:19 +01:00
Arınç ÜNAL
c6e412378c ramips: mt7621-dts: fix compatible string for mt7530 on TP-Link EAP615-Wall
The correct compatible string for the multi-chip module MT7530 switch in
MT7621AT, MT7621DAT and MT7621ST SoCs is mediatek,mt7621. Remove the
property on TP-Link EAP615-Wall which will default to the said string.

Fixes: a1b8a4d7b3 ("ramips: support TP-Link EAP615-Wall")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-03 13:49:51 +01:00
Jan Hoffmann
c46584ab30 ramips: use on-flash partition table for Sercomm BZV/CHJ
These devices have a partition table stored in flash, which compensates
for any pre-existing bad blocks by enlarging the respective partition.
This means that the current static partition table is only correct for
devices without any bad blocks.

Typical results of this mismatch are degraded wireless performance and
wrong MAC addresses, when the factory partition is shifted due to a bad
block somewhere before it. If there is a bad block already before the
ubi partition, then OpenWrt may not run at all because the kernel can't
find the rootfs.

Use the on-flash partition table to fix these issues. Replace the two
reserved partitions by the full partition list, as the driver does not
allow merging them.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2023-02-03 13:47:04 +01:00
Mark Ceeha
d4c63c7786 ramips: add support for TP-Link Deco M4R v4
This commit adds support for the V4 hardware revision of the Deco M4R.
V4 is a complete overhaul of the hardware compared to V1 and V2,
and is much more similar to the Archer C6 V3 and C6U V1.

Specifications:

  SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads)
  RAM: Kingston D1216ECMDXGJD (256 MB)
  Wireless 2.4 GHz: MediaTek MT7603EN
  Wireless 5 GHz: MediaTek MT7613BEN
  Flash: 16 MB SPI NOR

Installation:

Flash the *-factory.bin image in the U-Boot recovery webserver.
You can trigger this webserver by holding the reset button until the LED
flashes yellow, or by hooking up to serial pads on the board (clearly
labeled GND, RX and TX) and pressing `x` early in boot.

Once the factory image has been flashed, you can use the regular upgrade
procedure with sysupgrade images for subsequent flashes.

Signed-off-by: Mark Ceeha <hi@shiz.me>
Tested-by: Mark Ceeha <hi@shiz.me>
2023-02-03 12:13:50 +01:00
Dmitry Sokolov
39e4f03fd3 ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2
Device is the same as Xiaomi Mi Router 4A Gigabit, except of:
- 5G WiFi is MT7663
- addresses of leds, wifi and eth ports are slightly changed

Specs:
  SoC:  MT7621
  CPU:  2 x 880 MHz
  ROM:  16 MB
  RAM:  128 MB
  WLAN: MT7603, MT7663

MAC addresses:
  WAN     ****  factory 0xe006 (label)
  LAN     *:f7  factory 0xe000
  2.4 GHz *:f8  factory 0x0000+0x4 (mtd-eeprom+0x4)
  5 GHz   *:f9  factory 0x8000+0x4 (mtd-eeprom+0x4)

Installation:

Factory firmware is based on a custom OpenWrt 17.x.
Installation is the same as for Xiaomi Mi Router 4A Gigabit.

Probably the easiest way to install is to use the script from
this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155

In a more advanced case, you can do everything yourself:
- gain access to the device through one of the exploits described
  in the link above
- upload sysupgrade image to /tmp
- overwrite stock firmware:
  # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1

Recovery:

Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit.
Possible options can be found here:
https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition

One of the ways is to use another router with OpenWrt:
- connect both routers by their LAN ports
- download stock firmware from [1]
- place it inside /tmp/test.bin on the main router
- configure PXE/TFTP on the main router
- power off 4Av2, hold Reset button, power on
- as soon as image download via TFTP starts, Reset can be released
- blinking blue wan LED will indicate the end of the flashing process,
  now router can be rebooted
[1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin

Signed-off-by: Dmitry Sokolov <e323w@proton.me>
2023-01-28 22:11:44 +01:00
Maxim Anisimov
3690c4a092 ramips: improve support for Zyxel Keenetic Extra II
- drop unneeded default-state for led_power
- concat firmware partitions to extend available free space
- increase spi flash frequency to 32 Mhz (value from stock firmware bootlog)
- drop broken-flash-reset because of onboard flash chip W25Q256FV has reset support
- add compatible for pcie wifi according to kernel documetation
- switch to wan mac address with offset 0x28 in rf-eeprom

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-28 21:45:34 +01:00
Nikolay Martynov
62dbcb8305 ramips: Fix root volume for tplink-er605-v2
This device has two sets of volumes: main ones (`kernel`, `rootfs`, etc) and
'backup' (`kernel.b`, `rootfs.b`, etc). Bootloader tries to determine which set of
volumes to use by looking at contens of `extra-para` and `extra-para.b` volumes.
These volumes contain JSON that looks like this:

```
{
	"dbootFlag": "1",
	"integerFlag": "1",
	"fwFlag": "GOOD",
	"score":1
}
```

It looks like the bootloader looks for `"fwFlag": "GOOD"` (as opposed to `BAD`)
then it compares `score` field - whichever 'good' volume has bigger score wins.
This determines which set of volumes to use to boot.

So for example if `extra-para` is good and has bigger score then `kernel`,
`rootfs`, etc volumes are used. This means bootloader needs to explain to the
kernel which volume to use for the rootfs. After looking at bootloader code with
disassembler I think it contains a bug. Relevant part of code looks something
like this:

```
  if (image_id == 0) {
    rootfs_volume_id = 8;
    rootfs_volume_name = "rootfs";
  }
  else {
    rootfs_volume_id = 0xf;
    rootfs_volume_name = "rootfs.b";
  }
  sprintf(
    &buffer,
    0x800,
    "console=ttyS0,115200 noinitrd ubi.mtd=3,2048 ubi.block=0,%s
    root=/dev/ubiblock0_%d DKMGT_IMAGE_ID=%d DKMGT_IMAGE_TYPE=ubi",
    rootfs_volume_name,
    rootfs_volume_id,
    image_id
    );
```

Where `image_id == 0` if 'normal' (not '*.b' set of volumes is used).
However from device dumps we know that from the factory `rootfs.b` has id 8 and
`rootfs` has id 15.

So from above we can see that ids and names of rootfs volumes do not match. More
over - they are hardcoded in the bootloader.

Both things are problematic for OpwnWRT which completely removes volumes on
update meaning that volume ids may actually change.

So instead of relying on bootloader to provide the kernel with root device this
patch forces kernel to determine root automatically - and it defaults to
`rootfs` volume which is correct for our purposes.

Overall this makes image boot fine from flash after sysupgrade from inirams.
assuming `extra-para*` volumes make bootloader use non-'*.b' set of volumes.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
2023-01-22 14:37:47 +01:00
Harm Berntsen
09f313bfd7 ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.

Specifications
--------------
SOC   : Mediatek MT7621AT
ETH   : Two 1 gigabit ports, built into the SOC
WIFI  : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED   : Power (green+red)
LED   : WiFi (green+blue)
LED   : WPS (green+red)
LED   : Followme (green+red)
Power : 12 VDC, 1A barrel plug

Winbond variant:
RAM   : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1

Macronix variant:
RAM   : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec  4 2017 - 11:37:57), Ralink 5.0.0.1

Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.

The pinout is: VCC (the square), RX, TX, GND.

Installation
------------
See the Wiki page [1] for more details, it comes down to:

1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
   connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
   environment located at 0x30000

Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.

MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use      | address          | example           |
+----------+------------------+-------------------+
| Device   | label            | 00:00:00:11:00:00 |
| Ethernet | + 3              | 00:00:00:11:00:03 |
| 2g       | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g       | + 1              | 00:00:00:11:00:01 |
+----------+------------------+-------------------+

The label address is stored in ASCII in the board_data partition

Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
  both partitions for more storage space.

Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
  macaddr_add
- Only the power LED is configured by default

References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653

Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
2023-01-15 13:41:02 +01:00
Filip Milivojevic
990419dac3 ramips: cudy wr1300v1 reduce SPI freq to 10000000
Reducing SPI flash frequency allows the build to boot on both old variants
with W25Q128 chip and new variants with XM25QH128C chip.

The old 80000000 value only boots on devices with the W25Q128 flash.

This is also the change Cudy themselves made in their openwrt builds and
their .dts file.

Removed m25p,fast-read as it is not needed with slower speeds.

Signed-off-by: Filip Milivojevic <zekica@gmail.com>
2023-01-14 19:25:06 +01:00
Keith Harrison
c13263ca07 ramips: add support for D-Link DIR-1935 A1
Add support for D-Link DIR-1935 A1 based on similarities to DIR-882 A1,
DIR-867 A1 and other DIR-8xx A1 models. Existing DIR-882 A1 openwrt
"factory" firmware installs without modificaitons via the D-Link
Recovery GUI and has no known incompatibilities with the DIR-1935 A1.

Changes to be committed:
       new file:   target/linux/ramips/dts/mt7621_dlink_dir-1935-a1.dts
       modified:   target/linux/ramips/image/mt7621.mk
       modified:   target/linux/ramips/mt7621/base-files/etc/board.d/01_leds

Specifications:
* Board: Not known
* SoC: MediaTek MT7621 Family
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615 Family (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
        WiFi 5G (green)

Notes:
* 160MHz 5GHz is available in LuCi but does not appear to work (i.e. no
  SSID is visible in wifi scanning apps on other devices) with either
  official DIR-882 A1 firmware or a test build for the DIR-1935 A1 based
  on the 22.03.2 branch. 80 MHz 5GHz works.

Serial port:
* Untested (potential user damage/error)
* Expected to be identical to other DIR-8xx A1 models:
	* Parameters: 57600, 8N1
	* Location: J1 header (close to the Reset, WiFi and WPS buttons)
	* Pinout: 1 - VCC
		  2 - RXD
	          3 - TXD
		  4 - GND

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

Signed-off-by: Keith Harrison <keithh@protonmail.com>
2023-01-14 19:09:56 +01:00
Jo Deisenhofer
f204c812e9 ramips: add support for xiaomi RA75 Range Extender
This device is a 'Range extender' variant of the Xiaomi 4A router.
Its identical to the 100m non-intl/chinese version as much as it can run
the same firmware, differences being form factor, LEDs, WPS button
and one 100M port only.
The stock firmware differs significantly, being 'app managed only'.

Device specification
--------------------
SoC:      MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi:     MT7612EN 5G-ac 80MHz 2T2R
Flash:    16MB W25Q128BV
DRAM:     64MB built-in SoC
Switch:   built-in SoC
Ethernet: 1x10/100 Mbps
USB:      None
Antennas: 2 x external, non-detachable
LEDs:     2 programmable blue/amber
Buttons:  WPS and reset (hidden)
Housing:  Range Extender / Wall wart
Serial:   115200,8n1

MAC Addresses
-------------
All 3 MACs are read from flash and identical to stock.
Label MAC is WIFI 2G

Installation
------------
No HTML UI on this device, serial console only. The serial connector
is unpopulated but standard size and clearly marked. Flash from the
U-Boot shell at boot by choosing (2) and flashing the sysupgrade file
via tftp.

Recovery/Debricking procedures of the xiaomi 4A and variants should
work, but there currently is no official source for the stock firmware.

Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
2023-01-14 19:02:21 +01:00
Jo Deisenhofer
ab402f3d23 ramips: Move LED definition out of included dtsi into dts
Prepare for a new target with different led definitions that wants to
include this dtsi. The resulting dtb are unchanged, verified with dtdiff

Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
2023-01-14 19:02:20 +01:00
Mikhail Zhilkin
1a35edfbdb ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |              J2
    |
    +--- Don't connect

Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
   with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 't'
3. Load and run OpenWrt initramfs image:
      tftpboot
      bootm
4. Once inside OpenWrt, switch to the first boot image:
      fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Back to Stock
-------------
1. Run in the OpenWrt shell:
      fw_setenv BootImage 1
      reboot

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
   the OEM firmware

MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
|         | MAC example 1     | MAC example 2     | Algorithm   |
+---------+-------------------+-------------------+-------------+
| label   | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| LAN     | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WAN     | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2     |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).

Notes
-----
[1] WAN MAC address:
   a. First octet of WAN MAC is differ than others and OUI is not related
      to TP-Link company. This probably should be fixed.
   b. Flipping bits in first octet and hex delta are different for the
      different MAC examples:
      +-----------------+----------------+----------------+
      |                 | Example 1      | Example 2      |
      +-----------------+----------------+----------------+
      | LAN             | 68 = 0110 1000 | 50 = 0101 0000 |
      | MAC (1st octet) |         ^ ^ ^  |                |
      +-----------------+----------------+----------------+
      | WAN             | 72 = 0111 0010 | 54 = 0101 0100 |
      | MAC (1st octet) |         ^ ^ ^  |            ^   |
      +-----------------+----------------+----------------+
      | HEX delta       | 0xa            | 0x4            |
      +-----------------+----------------+----------------+
      | DEC delta       | 4              | 4              |
      +-----------------+----------------+----------------+
   c. DEC delta is a constant (4). This looks like a mistake in OEM
      firmware and probably should be fixed.
   Based on the above, I decided to keep correct OUI and make WAN MAC =
   label + 1.

[2] Bootloaders
   The device contains 3 bootloaders:
   - First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
     located on NAND Flash to load next full-feature Uboot.
   - Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
     bootloader includes recovery webserver. Requires special uImages to
     continue the boot process:
        0x00 (os0, os1) - firmware uImage
        0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
   - Additionally, both slots of the original TP-Link firmware contains
     Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
     magics and CRCs. We don't use this U-Boot with OpenWrt.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-14 18:36:33 +01:00
INAGAKI Hiroshi
1f5f2e588a ramips: add support for ELECOM WRC-2533GHBK2-T
ELECOM WRC-2533GHBK2-T is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC      : MediaTek MT7621A
- RAM      : DDR3 128 MiB
- Flash    : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN     : 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet : 10/100/1000 Mbps x5
  - Switch : MediaTek MT7530 (SoC)
- LED/keys : 4x/3x (2x buttons, 1x slide-switch)
- UART     : through-hole on PCB
  - J4: 3.3V, RX, GND, TX from SoC side
  - 57600n8
- Power    : 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-2533GHBK2-T normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

MAC addresses:

LAN    : BC:5C:4C:xx:xx:FD (Config,  "ethaddr" (text))
WAN    : BC:5C:4C:xx:xx:FC (Config,  "wanaddr" (text), Label)
2.4 GHz: BC:5C:4C:xx:xx:FE (Factory, 0x4       (hex))
5 GHz  : BC:5C:4C:xx:xx:FF (Factory, 0x8004    (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-14 15:41:00 +01:00
INAGAKI Hiroshi
9fe648166e ramips: separate and update dtsi of ELECOM WRC-2533GHBK-I/GHBK2-T
ELECOM WRC-2533GHBK2-T has the almost same hardware as WRC-2533GHBK-I,
so separate the common parts from dts to dtsi.
Additionaly, add color/function properties to LED nodes and change the
trigger of wlan2g/wlan5g LED to "phy*tpt" trigger.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-14 15:41:00 +01:00
Arınç ÜNAL
fc33c41c21 ramips: do not use GPIO function on switch pins on certain devices
The pins of the MT7530 switch that translate to GPIO 0, 3, 6, 9 and 12 has
got a function, by default, which does the same thing as the netdev
trigger. Because of bridge offloading on DSA, the netdev trigger won't see
the frames between the switch ports whilst the default function will.

Do not use the GPIO function on switch pins on devices that fall under this
category.

Keep it for:

mt7621_belkin_rt1800.dts: There's only one LED which is for the wan
interface and there's no bridge offloading between the "wan" interface and
other interfaces.

mt7621_yuncore_ax820.dts: There's no bridge offloading between the "wan"
and "lan" interfaces.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-01-08 12:31:52 +08:00
Sebastian Schaper
3c31f6b521 ramips: add support for D-Link DAP-X1860 A1
The DAP-X1860 is a wall-plug AX1800 repeater.

Specifications:
- MT7621, 256 MiB RAM, 128 MiB SPI NAND
- MT7915 + MT7975 2x2 802.11ax (DBDC)
- Ethernet: 1 port 10/100/1000
- LED RSSI bargraph (2x green, 1x red/orange), status
  and RSSI LEDs are incorrectly populated red/orange
  (should be red/green according to documentation)

Installation:
- Keep reset button pressed during plug-in
- Web Recovery Updater is at 192.168.0.50
- Upload factory.bin, confirm flashing
  (seems to work best with Chromium-based browsers)

Revert to OEM firmware:
- tar -xvf DAP-X1860_RevA_Firmware_101b94.bin
- openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \
  -out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ==
- tar -xvf FWImage.st1
- flash kernel_DAP-X1860.bin via Recovery

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2023-01-07 17:56:10 +01:00
David Bauer
8036fb8dd0 ramips: combine USW-Flex dual firmware-partitions
In order to maximize the available space on USW-Flex boards using a
dual-image partition layout, combine the two OS partitions into a single
partition.

This allows users to access more usable space for additional packages.

Don't limit the usable image size to the size of a single OS partition.
The initial installation has to be done with an older version of OpenWrt
in case the generated image exceeds the space of a single kernel
partition in the future.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-07 01:32:58 +01:00
Leon M. Busch-George
f6d394e9f2 ramips: add support for Cudy M1800
Specifications

  SoC:       MT7621
  CPU:       880 MHz
  Flash:     32 MiB
  RAM:       256 MiB
  WLAN:      MT7915 WiFi 6 (2.4/5 GHz)
  Ethernet:  2x Gbit ports

                  MAC
LAN        b4:4b:d6:2e:c7:b0 (label)
WAN        b4:4b:d6:2e:c7:b1
WiFi 2.4   00:0c:43:26:46:08
WiFi 5     00:0c:43:26:59:97

Installation

There are two known options:
1) The Luci-based UI.
2) Press and hold the reset button during power up.
   The router will request 'recovery.bin' from a TFTP server at
   192.168.1.88.

Both options require a signed firmware binary.
The openwrt image supplied by cudy is signed and can be used to
install unsigned images.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2023-01-06 19:22:52 +01:00
Maxim Anisimov
dbebfb88b5 ramips: add support for Keenetic KN-1613
Keenetic KN-1613 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7628AN.

Specification:
- System-On-Chip: MT7628AN
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 4x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): SoC Built-in 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-keenetic_kn-1613-squashfs-factory.bin"
   to "KN-1613_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-06 17:53:10 +01:00
Vincent Tremblay
2fab942ce1 generic: fix silicon labs spidev bindings
Fix Silicon Labs bindings in the spidev driver

Some bindings for Silicon Labs chips already exists upstream.
These bindings can be found in trivial-devices.yaml.

The existing bindings are using "silabs" instead of "siliconlabs" to
identify the manufacturer.

This commit add two submitted patches for silabs chips and rename the
manufacturer in the different DTS for more coherence.

Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2023-01-06 16:01:10 +01:00
Ignas Poklad
7801e814dd ramips: add Unielec U7621-06 32M build target
Add 32M build target

Rest of the details as per commit 46ab81e405 ("ramips add support for
UniElec U7621-06")

Signed-off-by: Ignas Poklad <ignas2526@gmail.com>
2023-01-05 00:10:14 +01:00
Shiji Yang
6760c7cbe5 ramips: enable Wi-Fi LED support for Afoundry EW1200
Add LED properties to PCIe node to enable Wi-Fi LED support.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-04 23:32:27 +01:00
Shiji Yang
0eefea2ed7 ramips: enable Wi-Fi LED support for Zbtlink ZBT-WE1326
Add LED properties to PCIe node to enable Wi-Fi LED support.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-04 23:32:27 +01:00
Nikolay Martynov
665c2154ef ramips: add basic support for tp-link er605-v2
This is a MT7621-based device with 128MB NAND flash, 256MB RAM, and a USB port.
The board has headers to attach console. In order for them to work two solder
bridges near those pads need to be made.

The defice has the following partition table:

```
0x000000000000-0x000000080000 : "u-boot"
0x000000080000-0x000000100000 : "u-boot-env"
0x000000100000-0x000000140000 : "factory"
0x000000140000-0x000007e00000 : "firmware"
0x000007e00000-0x000008000000 : "panic-ops"
```

`firmware` partition contains UBI volumes. Unfortunately I accidentally wiped
partition and I no longer have access to it.

`firmware` partition contains 'secondary' U-Boot which is run by 'first' u-boot.
It also contains various configuration partitions that include device info and
MAC address. There also seems to be 'primary' and 'backup' set of 'main' volumes.

U-boot has `mtkupgrade` command that just overrides data on firmware partitions.
Firmware file provided by TP-Link cannot be used with that command.

U-boot also has 'recovery' http server. Unfortunately I was not able to make it
work with manufacturer's firmware.

Manufacturer's firmware essentially contains multiple UBI volumes along with
'partition table'. Unfortunately I no longer can properly run manufacturer's
firmware so I cannot at the moment try to a support for building 'factory' images.

This patch adds support for initramfs image as well as sysupgrade image.

This seems to be pretty standard MT7621 board otherwise.

Things that work:
* network
* leds
* usb
* factory MAC detection

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
2023-01-04 23:19:19 +01:00
Marian Sarcinschi
c4b806d5c4 ramips: add missing LEDs to Asus RT-AX53U
This patch adds the missing LEDs to Asus RT-AX53U.
Based on PR #10400 and patch provided in #11068
 - enable the two LEDs controlled by mt7915e for wireless;
 - add label to power LED so it works properly and fix formatting;
 - add the USB LED;
 - switch LEDs are best left to be controlled by hardware for now.

Co-Authored-By: Ivan Rozhuk <rozhuk.im@gmail.com>
Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Co-Authored-By: Hartmut Birr <e9hack@gmail.com>
Tested-by: Felix Baumann <felix.bau@gmx.de>
Tested-by: Marian Sarcinschi <znevna@gmail.com>
Signed-off-by: Marian Sarcinschi <znevna@gmail.com>
2023-01-04 21:56:49 +01:00
INAGAKI Hiroshi
ef4e1ae18d ramips: enable BBT on NAND in I-O DATA devices
This patch enables MediaTek NAND BBT on I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.).

[WN-AX2033GR]
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[WN-AX1167GR2, WN-DX1167R, WN-DX1200GR, WN-DX2033GR]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-30 16:12:15 +08:00
Felix Baumann
3f1e9f6f3b
ramips: add support for read/write uboot env to Asus RX-AX53U
Add support for read/writing uboot env by renaming the second partition
to its stock label "nvram" and remove the deemed unnecessary
"read-only". Split the first partition "u-boot" in two, in order
to allow `fw_setenv` safe write-access to the uboot environment
variables.

This implements hauke's request from [1].
Based on the patch provided by Shiji Yang.

[1] https://github.com/openwrt/openwrt/pull/10400#discussion_r945153224

Co-Authored-By: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description, fix some whitespace problem ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-28 14:04:57 +01:00
Julien Dusser
b893aa7992 ramips: add support for Linksys E5400 and clones
Linksys E5400 is a 2.4/5GHz dual band AC router, based on MediaTek
MT7628AN. This device is also sold as Linksys E2500v4, E5300 and E5350
with the same hardware, but software speed limitations in vendor
firmwares.

Specification:
 * SoC: MT7628AN (580 MHz)
 * RAM: DDR2 64 MiB
 * Flash: 16 MiB NOR (W25Q128BV)
 * Wi-Fi:
   * 2.4GHz: SoC Built-in
   * 5GHz: MT7612EN
 * Ethernet: 5x 100Mbps
   * Switch: SoC built-in
 * UART:
   * 115200, 8N1, 3.3V (real u-boot speed: 119050)
   * Pinout JB4: 1:[3V3] (TXD) (RXD) [NC] (GND)

Flash Layout:
  0x0000000-0x0030000 : "Bootloader"
  0x0030000-0x0040000 : "Config"
  0x0040000-0x0050000 : "Factory"
  0x0050000-0x0ff0000 : "Kernel"
  0x0ff0000-0x1000000 : "CBTinfo"

MAC address:
  LAN: factory 0x28
  WAN: LAN + 1
  2.4G: LAN + 2
  5G: LAN + 3

Installation:
1. Connect to UART, use LF as EOL (not CRLF)
2. Set IP address
  - Press 4 during boot
  - setenv serverip <TFTPSERVER_IP>
  - setenv ipaddr <DEVICE_IP>
  - setenv bootfile openwrt-ramips-mt76x8-linksys_e5400-initramfs-kernel.bin
  - saveenv
  - reset
3. Load Openwrt Kernel image from TFTP:
  - Press 1 during boot
  - IP and filename should be already set
4. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2022-12-18 21:24:57 +01:00
Alexey Bartenev
3f201d1f8e ramips: add support for SNR-CPE-W4N-MT router
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A

Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
 "Administration/Management/Firmware update/Choose File" in vendor's
 web interface (ip: 192.168.1.10, login: Admin, password: Admin).
 Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 file by "System/Backup/Flash Firmware/Flash image..." in
 LuCI web interface (ip: 192.168.1.1, login: root, no password).
 Wait ~240 seconds.

Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
 Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
 Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
 new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2022-12-17 22:34:44 +01:00
Shiji Yang
6361a952af ramips: improve support for SIM SIMAX1800T and Haier HAR-20S2U1
1. Use ARTIFACTS to build factory image. This change allows users to
   generate initramfs factory image using OpenWrt ImageBuilder.

2. Override the default bootargs property defined in "mt7621.dtsi".
   Although we use the "bootargs-override" property to set bootargs,
   the default "bootargs" property will still be written into the
   device tree, so it is better to override it.

Tested on SIM SIMAX1800T

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-17 21:08:14 +01:00
Shiji Yang
a7d8b54f86 ramips: improve support for H3C TX180x series devices
1. Explicitly declare gpio pin groups to ensure that gpio works properly.

2. Override bootargs in device tree to avoid modifying u-boot envs during
   initial installation.

Tested on H3C TX1801 Plus

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-17 21:08:14 +01:00
Mikhail Zhilkin
0ec8d991c2 ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1.  Login to the router web interface under admin account
2.  Navigate to Settings -> Configuration -> Save to Computer
3.  Decode the configuration. For example, using cfgtool.py tool (see
    related section):
       cfgtool.py -u configurationBackup.cfg
4.  Open configurationBackup.xml and find the following line:
    <PARAMETER name="Password" type="string" value="<your router serial \
       is here>" writable="1" encryption="1" password="1"/>
5.  Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6.  Encode the configuration. For example, using cfgtool.py tool:
       cfgtool.py -p configurationBackup.xml
7.  Upload the changed configuration (configurationBackup_changed.cfg) to
    the router
8.  Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
    ETxxxxxxxxxx is the serial number from the backplate label)
9.  Navigate to Settings -> WAN -> Add static IP interface (e.g.
    10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
    10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
    ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
       sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
       printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
       reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
      cd /tmp
      for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
      tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
      tftp -l mtd.md5 -p 10.0.0.2

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | *:50    |
| WAN | label + 11 | *:5b    |
| 2g  | label + 2  | *:52    |
| 5g  | label + 3  | *:53    |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000

cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker

Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-12-13 23:06:20 +01:00
Jan-Niklas Burfeind
dce66899bf ramips: add support for Wavlink WS-WN572HP3 4G
Wavlink WS-WN572HP3 4G is an 802.11ac
dual-band outdoor router with LTE support.

Specifications;
* Soc: MT7621DAT
* RAM: 128MiB
* Flash: NOR 16MiB GD-25Q128ESIG3
* Wi-Fi:
  * MT7613BEN: 5GHz
  * MT7603EN: 2.4GHz
* Ethernet: 2x 1GbE
* USB: None - only used internally
* LTE Modem: Quectel EC200T-EU
* UART: 115200 baud
* LEDs:
  * 7 blue at the front
    * 1 Power
    * 2 LAN / WAN
    * 1 Status
    * 3 RSSI (annotated 4G)
  * 1 green at the bottom (4G LED)
* Buttons: 1 reset button

Installation:
* press and hold the reset button while powering on the device
* keep it pressed for ten seconds
* connect to 192.168.10.1 via webbrowser (chromium/chrome works, at
  least Firefox 106.0.3 does not)
* upload the sysupgrade image, confirm the checksum, wait 2 minutes
  until the device reboots

Revert to stock firmware:
* same as installation but use the recovery image for WL-WN572HP3

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-12-07 12:30:45 +01:00
John Thomson
7ea965b578 ramips: mt7621: mikrotik 760igs (hEX S) fix SFP
This device uses an AR8031/AR8033 chip to convert SoC gmac1
RGMII to 1000base-x or sgmii for the SFP fibre cage.
The SFP cage requires phy-mode rgmii-rxid, and without it will not
recieve any packets: ethtool -S sfp rx_fcs_errors will increase when
packets should be being received, but no other _rx counters will change.

Fixes: c77858aa79 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2022-12-06 01:47:36 +01:00
Senis John
a8f3c97ce8 ramips: add support for HiWiFi HC5611
CPU: MediaTek MT7628AN @ 575 MHz
Flash: 16 MB
RAM: 128 MB
Ethernet: 10/100Mbps x 1
Wlan: 300 Mbps
USB: USB 2.0 x 1
LED: red/green x 1
Button: reset x 1

1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh
2. Upload the openwrt firmware to the router via SCP
3. Login the router via SSH
4. Run `mtd -r write path_to_firmware.bin firmware`

I have tested on my device.
- The LED will display RED on power-on, After system start completed, trun GREEN
- Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device
- USB can working under official u-boot

Signed-off-by: Senis John <thank243@gmail.com>
2022-12-04 15:21:12 +08:00
Maxim Anisimov
21762e4653 ramips: add support for Keenetic KN-3010
Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT.

Specification:
- System-On-Chip: MT7621DAT
- CPU/Speed: 880 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100/1000 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin"
   to "KN-3010_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2022-11-20 16:44:24 +01:00
Ivaylo Ivanov
6afc355b2e ramips: Add support for D-Link DIR-3060 A1
Hardware specification:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HVSINA 128MB
RAM: Micron MT41K128M16JT-125 256MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7615DN 2.4GHz N 2x2:2
WiFi2: MT7615DN 5GHz AC 2x2:2
WiFi3: MT7615N 5GHz AC 4x4:4
Button: WPS, Reset

Flash instructions:
OpenWrt can be installed via D-Link Recovery GUI:

    Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
    Give it ~30 seconds, to boot the recovery mode GUI
    Connect your client computer to LAN1 of the device
    Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
    Call the recovery page for the device at http://192.168.0.1/
    Use the provided emergency web GUI to upload and flash a new firmware to the device

Signed-off-by: Ivaylo Ivanov <iivailo@mail.bg>
2022-11-13 22:36:06 +01:00